We used a new Dacor range vent only to have it go on and off. We called Dacor and they referred us to Desert Tech in La Quinta. The owner came out and said we needed a new unit for $775. We said just unplug it. He charged us $275 even though it took him less than 30 minutes. Stay away from Dacor AND Desert Tech!

I purchased all Dacor appliances when our home was built 3 years ago. The Refrigerator has been serviced 2 times already and now requires manual defrosting every month to keep it functioning. Now the double ovens broken! These appliances are expensive and a total nightmare...never buy them!

I have the Dacor 30 all gas range in my house and it is the best. The grates take up the whole top surface of the stove area, so I have a ton of room to cook on. Basically, I can fit 4 giant pots on the stove at the same time, so Im ready anytime a chili cookout might break out. This is also super convenient during tamale season and soup season because I can put up to 4 giant stockpots on the stove simultaneously. In the event that I spill, its easy to remove the grates and give the surface a nice wipe up. As far as the oven, I totally rule the holiday season because I can fit up to 3 full size 18x36 catering sheets in at the same time, so basically, I can cook 4 dozen or more cookies in one shot, leaving me tons more time with family and friends than if I was baking 1 sheet at a time. Thank you Dacor!

We bought our house in 2010 and our Dacor stove was supposedly newer. When I went to clean it, I found loose screws in the bottom. Apparently, the convection element is loosing its screws and washers. Ive had this appliance fixed once already when the cooktop kept clicking. The black plastic around the controls cracked mysteriously. It takes 3 hours longer to cook a turkey than it should. This is a strange stove, which supposedly cost a lot. I wonder if a convection part missing two screws should be used?

Lemon appliances. The dishwasher breaks every 6 month. The gas range top breaks every 6 month. The Microwave breaks every 6 month. Awful products!!!

Less than two years ago, we purchased a Dacor classic wall oven from a local high end appliance store in Durham, NC. Within a few months, the electronics started getting glitchy; the oven started beeping in the middle of the night. I turned off the beep, but other problems started popping up. I baked a pie which was half raw on one side and overcooked on the other side -- not exactly what you would expect from a nearly $5000 oven. Recently, the display has been blinking in codes and the oven has been turning itself off. When I tried to call customer service, I was repeatedly put on hold for 30 minutes after which the system disconnected me. When I finally spoke to a person, she was very rude. This is a horrible company, a horrible product and I deeply regret that the salesperson at the store talked me into buying this awful oven. I am extremely unhappy.

My oven would not work. Neither the broiler nor oven element would heat. The dealer from whom we purchased the range had gone out of business. So, I wrote to customer service on the Dacor site. Dacor customer service was back to me within 24 hours with a suggestion on what might be wrong. My husband followed the easy directions and my oven is now working! I am very happy with the prompt reply from Dacor customer service. They even provided a dedicated phone number if we had problems.

Most of my life, Ive always bought pretty low end appliances, and theyve always worked pretty well. When we remodelled our kitchen, we decided to go with a high end Dacor stove, and its been nothing but trouble. After just a few weeks, the igniters started to fire constantly on some burners. It was still under warranty, but it was very hard to find someone to honor the warranty. We got that fixed, then the oven light started to come on and off randomly. After our experience with the first problem, we just disconnected the light and let it go. A few months later, the bottom shelf jammed, and there was no way to collapse it to fit in the oven. This product is total junk. Dont buy it!

I had an issue with the wall oven light on my Dacor Preference double oven. To make a long story short, after contacting Dacor directly, they made sure that the unit was fixed by providing the part directly to me and confirming that the local repair company would be willing to install it. The oven is 8 years old and in the end, what I spent seemed reasonable to get a fully functioning oven (membrane switch). They were prompt, personal and courteous in their response to me. I came away feeling that Dacor takes pride in their history and their products! They also cleared up some misconceptions that I had regarding the status of their company. Although it was frustrating to have an appliance not work properly, I feel that the customer service Dacor provides makes their company one worth sticking with. That makes a big difference in todays impersonal world.

Dacor double oven range turns off by itself while baking - Disappointed in Dacor, especially today. Thanksgiving 2016: baking turkey. Sill baking turkey. I dont know when the oven decided to switch off this time, but I have an uncooked turkey and guests waiting. The oven has done this before, but because it was new I thought it was user error. Nope, the damn oven mysteriously turns off on its own. Incredibly irritated with Dacor. The range hood we also purchased is a joke. We remodeled our kitchen 1 year ago and wanted quality appliances. Bad move. Save your money, folks. Save your money.UPDATED ON 03/10/2017: Dacor sent a company out to fix the broken new oven. Oven still cannot hold its temperature (It takes FOREVER to heat then loses its heat while still showing a high temp). This time I have a recording on what happens when the oven automatically switches off. Disappointing when we spent nearly $10,000 in Dacor appliances for a kitchen remodel. DACOR, please have a rep contact me!!! Still waiting to hear back!!!

I have had my 30 inch Dacor Dual Fuel Range since 2002. In the past month, the oven door seems to be falling apart. I had to replace the oven door handle after the handle cracked in the spots on the right hand side where the screws go in. When I tried to screw the new handle in, I noticed that the front panel on the door is lifting away from the door. It is more separated on the right hand side which leads me to believe that it is the reason that the handle cracked on that side. As a result, the handle cannot be properly installed. The only way this can be repaired is to call someone in to do it and it will either have to be glued together or the whole door would need replacing. Reading these forums, Im worried that my oven problems are just beginning and I dont want to start sinking money into this oven. I purchased a Dacor as I believed it was a high quality product and that it would be worth the money and last a long time. This type of problem should not be occurring. I do not consider 10 years a long time for a product like this. My sister has had her Jenn Air oven for almost 20 years and it has no signs of wearing out.

My ovens have had to have a new board, dishwasher rarely works, my cooktop cant get parts needed! The worst appliances on the market!

It give the peace of mind, knowing that having a Dacor cooktop (RGC365) I have one less thing to worry about it. Food is always on time, and my wall oven is so simple to use and clean. Like I said one less thing to worry about it. I been a Dacor customer for over 12 years. There is no need to look any farther. My next kitchen will be a Dacor Set.

We bought a new house a couple years ago, and the kitchen came with a suite of new Dacor appliances - range, fridge, and dishwasher. They are all terrible.The led indicator on the dishwasher is scrambled. The icemaker in the fridge clogs up into a solid block of ice. We had this fixed, which involved a new control board and some caulking, but the problem returned not long after. The knobs on the range feel like theyll snap off any time. The lights in the oven arent seated properly and they interfere with the oven racks. It takes forever to get up to temperature. And Im starting to think I have a gas leak. How can these products be so expensive and such utter garbage? Oh, but they have wifi!

One year ago I completely changed out all appliances in my kitchen. My favorite of the four appliances is the range. We have enjoyed all kinds of new cooking techniques. As my wife put it, I did not realize how crappy my previous range was. Gourmet cooking is what Dacor is founded on and we could not be happier with the performance. Our favorite feature on the refrigerator is the in door water pitcher. Fresh cook water that can be taken to the table and refilled upon placing it back in the refrigerator. And the combi-microwave is an incredible second oven. All products have performed as advertised and promoted, and with a three year warranty whats not to love? Thanks Dacor for making amazing beautiful appliances.

We purchased the modernist collections 48” range, refrigerator and freezer, oven and microwave combo and dishwasher with a kitchen remodel 9 months ago. We had one issue with the dishwasher which was resolved, then another when is stopped mid-cycle. Repairman came out and was told we needed a new panel. Found out it was back-ordered. Well, it’s now been FOUR month without a dishwasher. We have contacted customer service and asked for other options and were told there was nothing they could do! When following up we have left messages and had our calls not returned, as has our service company. I have waited on the phone 3 times 30 minutes to talk to someone, because they won’t call back. We’ve asked to talk to a supervisor, and was told our information would be forwarded... 2 days later, no call. This is by far the WORST service I have ever had for ANY type of product.

My husband and I built our home and moved in November 2002. We purchased a Dacor Double Oven, Dacor 5-Burner Electric Cooktop and a Dacor Microwave. After the second year of living in our home, we started having problems with our double ovens. It would start beeping at different times. Sometimes it would last a few times to off and on for days. Then it would stop beeping and not return for a year. Now the beeping has started again and now it is displaying off. It wont come on. We have turned the breaker off and back on because sometimes that would reset it but not this time. Now before I could call anyone out to look at it, my 5 burner electric oven is dead. I called Metro in Tulsa, OK which is where we purchased them and they gave us the name of a repair person in our town. He came out and told us that we needed new boards for both appliances and charged us $50.00 a piece just for the evaluation. Now one week later, he is calling us and telling us that our 5 burner electric oven is discontinued! I dont want to have to purchase a new oven! I will also say that on my microwave, where the time is displayed it is blank across one line. I didnt even ask to have it look at. Please help!

We have a dual fuel Dacor oven purchased in 2001. We have the manual. For some reason, after cancelling a timer, the oven locked at :4. The owners manual was no help. The Dacor website was no help. We turned off the circuit breaker then turned it on again and finally, the oven worked.

We installed 2 Dacor wall ovens, a 5-burner cooktop, and a downdraft fan in 2000. The convection ovens bake perfectly and have performed without fail. After 7 to 8 years of daily use, we did have to replace the door hinge on the oven I use most often. We are in a rural area so the repairs are accomplished through Sears. The replacement parts arrived in a timely manner and the oven has worked perfectly since. The cooktop is easy to clean and the heat is even. The downdraft fan is effective and easy to clean. I would be confident to recommend Dacor products.

We did a major remodel in 2006 and were talked into Dacor Appliances by the kitchen planner. Big Mistake! The first time we tried to do the wall oven self-cleaning, the circuit board blew out. Since it was just past warranty and no one near us in West Virginia would work on it, I found a board online for $200.00 and replaced it. It has never heated evenly and now it wont heat past 350 F and maintain temp. The Dacor range hood sounds like a jet plane and the variable speed switch wont reduce rate. The bulbs burned out and after buying two online for $30 each, I removed the decorative housing and use a more standard $10 bulb. The Dacor gas cooktop is OK except that EVERY time you turn on a burner, one or two of other igniters start clicking and wont stop until you find which one it is (not always the same) and turn it on and off. Please heed this and all the other warnings from the choir. DO NOT BUY DACOR! It is all very expensive junk! I only gave it 1 star because there was no way to rate Dacor a zero!

Weve had these appliances for 15 years. The cooktop has worked well. However, it could be improved with a lower lever for heating on its small burners, allowing it to simmer water rather than boil. The Dacor exhaust we purchased is one of those type that pop up out of the counter. It works but leaves much to be desired. When it runs, it pulls so much air the flame goes out on the burners. It is still not efficient at getting rid of cooking smells or smoke either, but that is simply a problem with all of this design so I cant fault Dacor. We have the biggest problem with the double oven. There are three main issues: 1) Whenever we run the self cleaning function, it pops the heat safety switch inside the oven housing so I need to take it apart to fix it. Hence we work to keep it clean so we never use the cleaning cycle. 2) The oven door gaskets prevent to door from closing and sealing all the way. The door tilts out app. ¾ because of this. We were told by the service guy who came to fix problem 1 above that this is the way the doors are(!). Our bottom one also tilts out but not as much. Ive dealt with this for 14 years! 3) We have to sand the burner electrodes on the cooktop to ensure they spark to light the burners at least 2-4 times per year. Not sure if that is normal or not.

We have a Dacor Epicure 36 six burner range. It has been a regular source of trouble since it was installed as part of a kitchen remodel in 2006. The igniter for the broiler went out 18-24 months after we got the oven. A year or so after that the weld that holds the bottom oven rack bracket to the oven itself popped loose making it impossible to use the lowest rack position in the oven. Last year the circuit board that controls, among other things, turning the bottom oven element on stopped working. Not only is the board itself quite expensive, but it is buried deep under the top of the stove taking lots of expensive hours of repair time to remove and replace. And now the burner igniters have begun to over spark (e.g., continue to click long after the burner has been lit, burners sparking that have not been turned on). The repairman tells me that is a different circuit board so we could be heading to another $500 or so in repair bills or perhaps a trip to the dump and a much cheaper replacement range. We have had other Dacor equipment (cooktop, wall oven, warming drawer) and have not had a problem with any of them. But given our experience with the Epicure I cant imagine ever buying another.

Our Dacor wall oven (model MOH 1305) is the subject of my concern. Purchased with confidence in Dacor’s advertising in 2008. The oven has had multiple visits by a Dacor authorized repair company who along with a Dacor technician determined that the oven needed a relay board replacement. This relay board has been replaced twice and has failed after installation both times. The relay board provided by Dacor appears to be the problem. Each repair/service call costs approximately $300.00 with no guarantee that the next relay board will work. Our conversations with Dacor give us no satisfaction. Dacor now tells us that our “superior product” of 11 years is just too old. Additionally, they tell us that Dacor products are “superior products” that are designed to last somewhere between 10 to 15 years. There is no excuse for Dacor since the replacement relay boards they are sending us seem to be defective. Their excuse that we have an “old” oven is wrong since the problem is with their defective replacement parts. Beware consumers when thinking about purchasing Dacor products.

For the second time in 7 years our Dacor ERD 48 Range has failed us. Just in time for our New Years Day dinner. Neither of the two ovens will heat. We are now encountering the exact same problem. We spent $1000 the first time replacing the board. We cannot afford to do it twice.

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

DCT305SNGH - I have owned this stove for about 3 years already. From the very beginning it has been trouble. The lights that turn on when a burner is on broke immediately. The place where the gas comes out and ignites is black and hard to clean. The grates are rusty, the finish has come off. The indicator knobs dont reflect what is happening in other words if it is on the lowest setting you dont have any indicator marking. It is hard to clean and scratches very easily. I have had the service person out about 5 times until they decided to send me many new parts. These arent any better. It is just a bad product. Basically the warranty is useless if you keep calling for the same issue. They say, This is the last time we will fix this issue. Sadly I always heard this was a great company and I waited 7 years to save up for this stove and boom rotten appliance.

Dacor representative has been helpful in responding to my complaint and has sent new oven racks which I greatly appreciate. I was able to send them pictures of the damaged racks. I want to clarify that the warranty that was sold to me by an upscale appliance center was NOT a Dacor extended warranty and I believe that this caused my issues to slip thru the cracks. Nothing can be done about the interior that seems to have a film of sorts on it, short of replacing, but I am grateful that Dacor customer service went out of the way to correct the problem with the racks.

We remodeled our kitchen in 2002 and chose the Dacor 36 dual-fuel range. I was preparing a pork roast for a dinner party with the oven on Bake. The roast was just not coming up to temperature, though the display indicated that the oven was at the temperature I set. I wound up slicing the roast and cooking it on the griddle; my hungry guests were getting restless. Then I tracked the oven heat for an entire day with an oven thermometer. The oven would come up to temperature and then cool off. I sent these numbers to Dacor and asked customer service for an explanation. Believe it or not, the conversation was--Dacor: The temperature is going down because the fan is coming on. Youre not supposed to use the Bake setting, but only the Convection Bake or Pure Convection. Me: Why is the Bake button there, then? Dacor: Were taking it out in the next production run. (This hasnt happened. My sister-in-law bought a Dacor last year before I could warn her and the button is still there.) Also, after using the self-clean one time, I noticed a crack on the inside of the oven door, starting in the corner of the window. The inside of the window is now permanently spotted with baked-on grease. Now my oven does not work at all. The repairman says that the circuit board needs to be replaced, and if Im lucky, it will work for a couple of years. The repair will cost around $700 including labor. The repairman told me that some repairmen in our area will not even work on Dacors because there are so many problems. Im considering replacing the stove... a very expensive mistake. Beware of Dacor products.

Our Dacor oven is 2 years old and the oven door stopped closing all the way, rending it inoperable. The company is now owned by Samsung. I tried to schedule a service call to repair/replace the door hinges. This should be a simple process. However, because I purchased the oven through a designer and Dacor dealer, I had to track down the order verification to demonstrate that I am the original owner of the oven (this is in addition to providing a copy of the receipt or proof of purchase). It took several days to resolve this issue with my designer and rep who sold me the oven. Then, I scheduled the service call on the phone only to receive an email hours later advising me that the service call had been cancelled. No explanation was provided. After rescheduling the service call several times only to have each call cancelled, something finally worked with Samsungs tracking system and the service call actually took place.Dacor is the Mercedes of ovens and I expect a service call to be a little more expensive. However, other providers of luxury products facilitate the product support to minimize customer aggravation. Samsung needs to work on its product support and customer service. I would not purchase a Dacor product again since there are several other manufacturers that provide comparable luxury kitchen appliances with much strong customer support.

We purchased this unit 7 years ago, just a family of two with visiting grandchildren. Unit came, had a crooked door and a bent latch, which we had serviced and supposedly corrected. When self cleaning the latch still made grinding noises. Over a year ago the oven stopped working period. A December service call said needs a new latch, sensor and display -we are now in 4 figures($). Oven operates for month and a half. January 2019 Service call now new door latch, relay board and main wire harness 4 figures again double! Oven stops working yesterday (June). Service call today new latch, motherboard and something else and another 4 figure repair cost. Same repair parts same problem! Patience is a virtue, but repair costs are sinful! Next step, Boat Anchor! Problem from the beginning and still a problem now.

I replaced my Thermador Wall ovens with Dacor because the size and I would have to do less retro-fitting of my cabinetry, this was a grave mistake. Here are the issues with Dacor.1. The high heat sensor trips and you need to call a service professional to have it reset. This gets very expensive. I have tripped mine three times, once baking a cake at 350 degrees, once during self-cleaning and another during normal cooking. The Dacor Service Help said this was a common problem because the heat sensor is located near to the touch panel.2. The oven vents from the bottom of the unit into the room heating my kitchen.3. The glass window does not seal so I have stains in-between the panes of glass. Not very attractive to stare at large drip stains.4. It takes an exceptionally long time to pre-heat oven and convection mode even longer.5. The temperature cycles through and does not maintain its cooking temperature causing underdone results and longer cooking times. This is especially challenging when cooking roasts and large turkeys because they may take up to an hour longer than expected.Overall, I do not recommend this product.

After remodeling our kitchen, we purchased a professional line Dacor stand alone gas range/oven. Within a year, the heating element needed to be replaced. Subsequently, the control panel almost caught fire and needed replacement, following a second heating element. The oven is not reliable and has cost us over $600 in repairs, labor and parts. The Dacor company is not willing to recognize that this oven is a lemon, even though their rep admitted that the number of repairs seem to exceed the average number. The company refuses to pay for a tech to come in to examine why this range continue to have electrical problems. It is not working again, and the customer service rep wants us to pay out more money to have their tech diagnose the problem and pay the cost of repairs and labor, while they will cover the cost of the parts. I am done paying out more money on a defective appliance. I could have purchased two new less expensive (and more reliable) ovens by now.

Dacor range - After I posted my comments on August 8th, I was contacted by Dacor customer service immediately and the new part was sent to me free of charge. I do have to pay the labor, but the part was what was expensive before. They did give me an explanation as to why this was happening - the hinges on the door wear out and the door doesnt shut properly so that heat escapes. Should this be happening with a stove that was this expensive? I dont think so, but I am happy with the customer service I received from Dacor this time.

In 2008 I had the luxury of choosing kitchen appliances for our new home. I looked at them all and felt Dacor was the best choice. Choosing Dacor for our kitchen was the worst mistake I have made in kitchen appliances in any house in which I have lived (and there have been quite a few). The oven (48 dual fuel range) didnt work from day one. There was a problem with the temperature control. The oven would not shut off when it reached the desired temperature. Disappointing, but I told myself that sometimes things can go wrong and it should be an easy fix. Well, many service calls later and several re-wires of the unit, along with the installation of many new parts, the range still does not perform as well as the worst oven I have ever had.There is a tool that comes with the range that is used for taking the top off the unit to access the wires. My range was taken apart so many times that the tool wore out and had to be replaced. The front piece of the range no longer fits flush with the rest of the range. On one of our last service calls, I was told by the serviceman that Dacor said that under no circumstances would they consider replacement of my obviously faulty, beyond repair range. Eventually I got tired of repeated service calls. Sometimes servicemen would come out and say they didnt know how to fix it and leave. I would not expect such poor customer service from an entry level company. From a company touting themselves as a manufacturer of top of the line products, I would expect a greater desire to stand behind their products.The oven still does not work well. On convection bake, I must turn cookie sheets around or I will have doughy cookies on the same sheet as burned cookies. And forget using the convection setting to bake 2 sheets of cookies at once - it takes longer than baking them separately. I wish I could attach a picture! I also chose a Dacor microwave and refrigerator. One of the salesmen I spoke with about refrigerators said to make sure the unit we select did not have air transfer between the refrigerator and freezer, and the Dacor model did not do this. Well, when my 48 side-by-side arrived, it had the air transfer. I was disappointed but chose to live with it. Of greater concern to me is the noise the unit makes at times - sometimes loud enough I can hear it in other rooms of the house. I have not bothered to call for service. Im not interested in another fight to get Dacor to stand behind their poor quality overpriced products.At this point, I have no expectation of Dacor standing behind their products. I just want to share my experience with others who may be in the same situation I was - designing their dream kitchen - and save them the regret and continual disappointment in their Dacor products.

I have 2 single ovens side by side and have a cooktop and ventilation system - my experience with the cooktop and vent (2000) was so good that I did not hesitate to buy Dacor MorS130S ovens. They were installed in my new kitchen in September of 2012. I had my cooktop and ventilation system reinstalled. My daughter accidentally cleaned the oven without taking out the GlideRacks (which are hard to take out). We oiled them, etc., like the manual says if they are accidentally left in - they will not glide at all and now I am being told $300 each to replace excluding the cost of the service call. This is ridiculous. What kind of design is so poor that racks would get in this condition? I had Bosch ovens before and their warranty was wonderful and I, luckily, bought a Miele dishwasher which has a 10-year warranty. I would not buy Dacor again because of the warranty and because of this problem. I am beyond disappointed as I love my cooktop etc. I feel that Dacor should at least pay for part of these GlideRacks.

I did a kitchen remodel in 2008 and was convinced by the sales guy at Home Expo to go w/ the Dacor over the Wolf. I bought the dual-fuel 36... Within 2 years I had serious problems. The oven, when not on Convection Roast or Con Bake, just using Bake will consistently turn itself off... Ive ruined many a meals, usually big ones: Turkey, Prime Rib(long cook time items). This was by far my most expensive investment in my kitchen and by far my biggest disappointment. I have called Dacor in the past and was told they could refer me local repair people, I was on my own for fixing it. Again, huge disappointment.

We purchased a home with a 5 year old Dacor Discovery IQ Double Wall Oven. Model Number DYO230S. Great looking and it has a very sophisticated and functionally rich digital control system. Problem is the digital control system does not work. The stove has a mind of its own and will just shut off for 24 to 48 hours and return to function randomly. Shutting the power off and turning it back on has no effect. Dacor (Now Samsung) has been completely un-helpful. Bottom line response - tough. Product is no longer produced, replacement parts no longer in stock - maybe there is a part on eBay ** Honest that is the answer. I have called parts companies who also complain about Dacor (now Samsung). No luck. So we will now need to purchase a replacement product for anywhere from 4,000 to 10,000 dollars. To replace a 5 year old - 8,000 product. It will definitely not be a Dacor or Samsung product. And I will do my best to put similar reviews on the internet where ever I can.Just to add some balance - 21 years ago we custom built a home and purchased two Dacor ovens. Both were great. 21 years of flawless operation. When we saw this oven as we went through the home purchase process we were delighted. What a disappointment. Also - before the oven started to go wacky on us we needed to replace the bulbs (2) in the oven light fixture. Initially I contacted Dacor parts and had a very pleasant experience ordering the two replacements. However nothing came to our home. Called again and found that Dacor had been sold to Samsung and the price of the bulbs had doubled or more. No exaggeration. Stay away from Dacor and Samsung.

Perfect size burners and small oven. Cooks food perfectly about 25° less than you think. Great grill on top. Easy to clean.

We have enjoyed our Dacor oven for a number of years but cannot recommend this brand due to high cost and frequency of repairs. The relay board, at $400 a pop parts cost only, has had to be replaced twice within 5 years. The oven door hinges failed in normal use so that the door would not close tightly and had to be replaced. The halogen oven lights fail frequently requiring replacement. Parts cost is only part of the issue. The inconvenience of not being able to use the oven for extended periods of time and high appliance repair labor costs are significant. All in all, a very good oven but reliability and frequency of expensive repairs lead us to not recommend Dacor ovens.

If anyone else has this experience with Dacor ovens, we need to have a class action suit against Dacor! While baking Christmas cookies this week with my grandchildren, my ovens stopped working and started beeping. The error code was F3. I was able to get a technician rather quickly who diagnosed the problem as a failure of the control board which affected both ovens. The replacement part was discontinued from production in 2011. My ovens are 12 years old and cost over $4,000 at the time. What a pickle I was in a week before family coming for Christmas dinner!The technician said my only recourse was to send the control board to a refurbisher and he did not know when the board would be fixed - all for a whopping costs of over $600.00! I find it unacceptable that Dacor discontinues a control board and forces the consumer to either buy new ovens or pay the cost of a refurbished part that I hope will work. After spending thousands of dollars, how does this happen? What can be done so the consumers who purchase appliances with good intentions are protected from manufacturers that dont stand behind their products? DACOR I NEED ANSWERS!!

I have had nothing but trouble with a wall oven I bought in 2010. Basically just bad electronics. I finally replaced the oven in 2014 and had to get another Dacor to fit the opening. The new unit still does not heat evenly and is consistently off by about 50 degrees. Customer service is not helpful at all. Local repair shops cant really fix issues. Terrible company. Cant figure out how they stay in business.

Thank you for your attention. Since my post, a resolution has been reached and Dacor will be replacing my range with a new one. That is much more representative of the pride and reputation of Dacor. The executives were very responsive. Perhaps front line agents are not empowered to make these decisions, however, in my case, the escalation brought the matter into the right hands. Happy with the direction towards the final outcome, not the 4-month process that discounted the reputation and my perception.

We purchased a Dacor 30 Heritage Gas range and installed it in early Oct 2020. Within a day a gas leak from the back of the range was identified by our gas contractor. Dacor repaired it quickly (12 hours). I was impressed (though concerned it already had an issue). In December 2020 I noticed that the oven indicator light was not coming on. I contacted customer service and despite indicating that there was a problem, was simply told what the light was for. Then, in February 2021 (under 5 months after installation) the oven stopped working. The service technician indicated it was an electrical issue and the gas would not ignite. It has now been over two weeks and we still do not have it repaired nor any indication of when it will be repaired. We spent $5200 on this range. I do not recommend Dacor.

In September 2009 we did a complete remodel of our kitchen. Replaced everything but the refrigerator, with DACOR appliances. Within a few months we had problems with the dishwasher and finally replaced it with a GE in 2012. About that same time we had problems with the Dacor Epicure 30 Single Oven Model EO130SCH control panel and had to have the repairman out to work on the relay/computer board. At Christmas 2015 I had trouble baking, the temperature wasnt accurate and have had the repairman again. He says that the computer board is fried (his term). Ive tried calling Customer Service with no success. Ive e-mailed them with same results. The appliance repairman has told me that he cant find the part. All the distributors that hes called have been told that the part is on back order. Ive been without an oven for over two months now with no fix in sight. Have been told that IF we find the part it will probably run around $500.00. These are appliances that are only six years old and have had gentle use by senior citizens. Anyone reading this - PLEASE DONT BUY DACOR! Youll be sorry as I am.

Ive had this range for two years and am replacing the control panel for the second time. 1st time during product warranty and second time out of warranty. The range is beautiful but apparently the electronics are bad. And to add insult to injury Dacor doesnt stock replacements but has them assembled when needed. Estimated wait time for a new panel is 3 weeks; so no oven for 3 weeks and now not a lot of faith that the new board will be any better than the last one.

October 2013 we had the Dacor model# EORD230SCH installed. It broke just in time for Thanksgiving! After several attempts of repairs, Dacor replaced this oven model# EORD230SCH with the next newer model at no cost. Not more than one month later the replacement oven doesnt work. Service is painfully slow. We had a 03 year warranty on the original purchase and the clock keeps ticking from the date of the initial installation. WE have asked for and been denied by Dacor, to reinstate the 03 year warranty once the unit is actually working. We bought this unit, spent extra money, thinking we were buying quality. So, two ovens in less than one year, doesnt equate to a quality product to me. Keep getting the standard answer about the warranty - no added time will be assigned.

We purchased a Dacor oven stove top. It is about 10 yrs old now. 3 years ago we had a problem with the ignitor and had it repaired and paid over $200.00 for the repair. 3 Years later we are experiencing a similar problem with the ignitors clicking on and not turning off. I have called for repairs on this but expect this will cost me some more money. I have been online and have seen similar complaints leading to believe that this is a common problem and I would avoid purchasing Dacor ignitor products for the stove top, until resolved.

We have owned our dual-fuel Dacor stove for about four years. We purchased this stove because we needed a down-vent - this is how our kitchen was already configured. We had only the Dacor or Jenn-Air stoves as choices and went with the Dacor. I have been thoroughly pleased. Everything works consistently including the self-cleaning feature. Prior to this stove, we had a Thermador which was expensive and NEVER worked consistently. One feature or another was always on the brink. The Dacor is such a relief. And good looking, too.

I just had an appliance repair company come out to let me know what is wrong with my Dacor Stove door, since it wont close. He said the hinges are needing to be replaced. He said that he replaces these hinges on Dacor stoves ALL THE TIME and that the company really needs to file a recall on these hinges and/or reimburse consumers who have these installed. He said these should not go bad like they do. That this is poor manufacturing on Dacors part and they are not being held accountable. I agree 100%. It is going to cost me with labor and parts almost $ 400.00 to replace these hinges that should not go bad with the age of the stove. Thanks.

Like many of you on this site, when we remodeled our kitchen in 2000, I researched and decided to shell out the extra money for the highly recommended and higher priced Dacor everything. We got a double oven, glass 30 cooktop and an exhaust fan. 12+ years later, I wish I had bought GE! My ovens have had so many problems I cant even count. Basically, the temperature doesnt hold correctly. I have used oven thermometers and my husbands fancy gauge to check temp. I had a whole transformer and control panel changed out in hopes that it would correct the problem, but it didnt. I think it has something to do with the self-cleaning. I think it gets so hot that it fries the controller. I never use the broiler so its not like I left the door open and wasnt supposed to. This afternoon I set the oven to preheat to 350. I set my little cakes inside that I was making with my grandson. About 5 minutes later, it smelled like something was burning so I checked the little cakes. They were already charring on top and then I noticed that the top element was fiery red, basically on broil! What the heck?! This is ridiculous! Im not going to spend another $500 for another repair! I am waiting to see what the repairman says.On another note, my stovetop cracked twice! The last time, Dacor was nice enough to sell one to me at cost and my husband was able to install it. It didnt match the old one and I was told by Dacor that they dont make them anymore and that is made by a third party supplier now. The old one had a textured finish and this one is just very shiny and scratches so easily! I hate it. We also had a retractable exhaust fan put in because the stovetop is in an island. Every time I turn it on, my basement smells like whatever is cooking. Now the buttons dont work anymore. That is unless I jab them so hard with a sharp object that it finally makes enough contact to work! This is another part that we got at cost that my husband had to crawl around and repair that still doesnt work.So, all three Dacor appliances we bought have turned out to be very disappointing purchases. Dacor should stand behind their products better, offer longer warranties or better yet, build better products! I would never recommend these products to anyone!

We were incredibly disappointed, not only with the range but with the customer service from Dacor. We purchased this range in January 2016 and here we are in July with what is basically a pan holder sitting uselessly in our kitchen. Problems started immediately. The first time I used the oven, it locked with the cooking food inside. It turned out that the thermostats on both ovens were so out of whack that the oven temperature reached self-cleaning mode levels so the ovens locked with the food inside! We had both thermostats replaced twice and still had the same problem. Eventually, the thermostats were calibrated, but still within a range. In addition, the switch for the convection oven just stopped working. After 6 months of trying to deal with this problem, we will be returning the range and replacing it with a different brand. At no point did Dacor offer to exchange the range, they simply kept sending a repair person.

We built a new home in 2004. All appliances were Dacor. Since then, the oven has had to be repaired 4 times; the microwave had to be replaced; the cooktop has had two repairs and now will not light automatically; and the patio barbeque completely burned up and some of the parts melted. I did report that to the company and to the US Product Safety Commission. We have not abused any of these appliances and have followed the manufacturer recommendations all of the time. Dacor charges top dollar for their appliances, but they are not as good as cheaper brands. If you try to contact Dacor, they have a well-so-what attitude.

Dangerous condition! I purchased a Dacor 36 dual fuel range 5 years ago. I reported the issue to Dacor via email with no response from customer service. I believe the no response was an attempt by Dacor to distance themselves from their responsibility for this potentially dangerous condition. Specifics: When pre-heating the oven in convection/bake mode, if the oven door is opened before reaching the set pre-heat temperature, a ball of flame will explode up from the opened door. The ball of flame is basketball sized and has singed eyebrows and hair on several occasions. To reiterate - it is a ball of flame, not super-heated air that is the problem. As a result, after non-response from Dacor, we called a decor qualified repair technician who diagnosed the problem as a bad igniter. The igniter was replaced and the problem still exists. I fear that a small child may be severely burned by the engineering design fault.

I am writing to complain about our Dacor dual fuel stove that we purchased in 1998 when we built our house. Initially things went well, and I enjoyed baking in the oven and the convenience of the gas stove top when we had power issues. But then the honeymoon ended, and the problems started. After completing our first self clean cycle, we started getting the F1 code, and noticed cracks in the front on the stove. Our repair guy came out, took a look, and then informed me that Dacor had had numerous problems, and were not so good about living up to their warranty. He was right, Dacor felt in no way that they should help resolve our problem. With 4 kids, you cant just go without a stove, so we paid for the parts and repair. I figured it was just a one time thing, but I was wrong. We are now again looking at replacing the same part just 3 years later again with cracks and the F1 code. Dacor should be ashamed. Do the math. If they walk away from responsibility on all of these faulty products that average $5,000 a piece, shouldnt they have the money to pay for the fixes or maybe hire better engineers? They need to be held accountable for this mess. I need my oven back on!!!! And after the money we have paid for repairs, light bulbs, and parts...... the rest of the care should be free and on them.

My stove is 3 years old and I have had to change the LED lights on the burners 5 times. One of the burners warped and was changed. The computer went after 2 years, now I have a gas leak in the burner hose. I have bought the extended warranty. I would not recommend this stove if you like to cook. Just make it look pretty in the kitchen!

I had a Thermador kitchen for more than 25 years and I was very happy with their products; I had a Thermador slide-in range with downdraft vent and a dishwasher and a KitchenAid refrigerator, but it was time to upgrade. Now, I upgraded my whole kitchen with all Dacor products and I am super happy, my 30 inch range top has extra wide grates which allows my wife to cook with extra large pans when she prepares food for donation, my updraft vent catches smoke and grease much better than my downdraft, my refrigeration is very nice looking with french door and middle refrigeration for my cold drinks and my dishwasher is very quiet. I invited a few friends home and they have admire my new kitchen. It has been more than months since I bought it and no problems.

We purchased this oven February 2009. On 6/7/11, we had to replace the touch pad assembly. On 12/16/13, we again had to replace the touch pad assembly with a cost of repair to this point of over $900.00. The over cost $2,395.00 when purchased. On 3/16/14, while on convection/bake the oven switched over to broil. On 3/20/14, a repairman came to the house. The condition did not replicate but the repairman, in conversation with Dacor, determined that the fix, if this should happen again, would require the replacement of the relay board and ERC control at a cost of $700.00. On 3/27/14, while on convection/bake, the oven switched over to broil. I called Dacor and was forced to leave a message.

Follow-up to March 31 posting: In 2001, we installed two Dacor wall ovens and a gas (converted to propane) cook top. The cook top has been problem free and the brushed stainless steel surface still looks like new. Both ovens however, at that time, were problematic during the two year-warranty period. Knowledgeable service people were hard to come by in our region. After numerous service calls, Dacor replaced one of my wall ovens at or around the three-year mark (outside of the warranty period). That particular unit had only one minor issue since then and Dacor replaced the appropriate part free of charge. The other original unit has been problematic since the beginning. The latest problem being the internal light going on/off for no reason and then a lack of response to light button on the front control panel.Long story short, I posted my frustration here on March 31 and was contacted by a Dacor rep within two days. He asked me for detailed info on the problem and located the unit in their files. Some of the past repairs were known to Dacor, but others were not since we just did them ourselves. I was asked to send a detailed description of the current issue along with pictures, which I did. Based on Dacors analysis or the pictures and the exhibited problem, they sent me, free of charge, a control panel membrane, a door gasket and a set of door hinges. We installed these items and the unit is now in full working order.In looking back over the past years of problems with this particular unit, its clear to me the issues all stemmed from an original broken door hinge. It was compounded by the fact that the service and repair folks at the time considered the door gap to be within tolerance and we did not discover the broken hinge until the door glass shattered and we needed to replace it, which required removing the door. Anyway, at this stage in the game, I am very pleased with Dacors response. It is my impression that they are trying much, much harder to stand behind their products. So, while just a short time ago I would have never considered another Dacor product, when the time comes, they would still be on my list of considered vendors because when these ovens work, they work great.

I purchased my Dacor Distinctive #DT0127 wall oven in 2015 and have been very pleased with the product to date. However after running a self-clean cycle the oven does not work which was a surprise given the fact that I had previously done self-cleans before without any problems. I immediately contacted Dacor customer service who were amazing! The CSR that I spoke with kindly extended my warranty until 2018 even though I had not registered my oven with them upon purchasing it. He also arranged a service call for me that would be covered under the extended warranty. I am very impressed with the companys attention to service as I really love my oven. Even though I experienced this issue I would still recommend this product.

I built my home in 2003 and installed a Dacor 30 wall oven. After several years of poor performance, we started to get an error message. Dacor suggested replacing a board for $300. That didnt work so they had me replace another $300 board. That didnt work so they told me I needed a new front panel and it would run about $1,000. That board is on back order and they dont have a replacement date. Thinking that its bad business to sink $1600 into a troubled product that has terrible reviews on the internet. We found out that once you go with Dacor, you need to stay with Dacor due to an unusual, nonstandard size.Thinking that Dacor has improved their product we ordered a brand new $3,000 Dacor RO130 30 wall oven. It arrived promptly and I removed the defective $3,000 oven and put in the brand new $3,000 Dacor RO130 oven. What I got was a dead brick. The Dacor customer service has been awful, and will not allow me to talk to anyone in their technical side. The oven is getting power. Dacor customer service wouldnt help me unless I could prove that the unit was getting power. So I had to get an electrician in to prove that I had properly wired the 4 cords that came off the original defective Dacor wall oven. Get service help? No chance. I live 100 miles from Seattle and no one wants to work on Dacor. So here I sit with a $3,000 brick. No service and Dacor has no clue on how they will service this wonderful $3,000 RO130 30 wall oven that is an out of box failure. I dont see how a company that has this bad of a product, two generations of defective ovens, bad customer service, reluctance from the repair community to work on their products will be in business much longer. If you are considering Dacor appliances, consider the problems that I am having. The nonstandard size of their ovens will lock you into future purchases to replace their products that dont last 10 years.

I owned a 36 Dual Fuel Epicure range that required at least an annual repair for the same thing. The control pad (the pad with the buttons that controls the oven and light) would fry. This would cause the oven light to come on and off like a strobe light. Luckily, I purchased an extended warranty from the vendor, as each time this was replaced it was $750+ to repair. When I complained to Dacor on their support line, the representative actually told me that I was running the oven too hot!About 6 months ago, I sold the house and left the very expensive range behind. It was problematic from day one. Other repairs included replacing the ignitors. After a year of use, the insulation on the door came loose and was hanging in plain view through the window on the door. Every repairman that came to service the range said the same thing.... that they repair a lot of Dacors. When it worked, it was a great range. If you do buy a Dacor, do yourself a favor, buy the extended warranty. You will need it and it will pay for itself.

I have a induction Dacor stovetop. Its stopped working and blinks an error code. Called customer service who didnt know what the code meant. I was told my model was 2015 which the rep said was old. It was installed in 2017. All they would offer was cheaper replacement parts if I paid for someone to come and figure out what the problem was and install the parts. I was told the replacement parts were not cheap though. I was told that because were the second owner of the house they couldnt fix it under warranty (even though it should be covered under warranty) because they couldnt say how it was used before (commercially or residentially). Give me a break!It gives me almost no confidence in getting this thing fixed. Warranty is a joke and customer service is terrible. So far I had to leave a voicemail for the reps next level who will call me back after the weekend. Im waiting to see what (if anything) they will do but from the first rep. I dont have a lot of confidence in their products.

We remodeled our kitchen in 2006. I spent a fortune on a Dacor dual fuel gas cooktop with electric oven/convection oven. My Dacor problems seem so normal I mostly deal with it. My 2 biggest complaints are the glass oven door is not airtight, it is darkened between glass, very hard to monitor my baking. And the temp gauge has always been off by 15-25 degrees. I use an in oven temp gauge, which has been calibrated so I know it works. If anyone is planning on a Dacor, you will get the best looking range. It just wont work.

About 3 years ago, I spent almost $5,000 on a Dacor double oven. We had it less than 3 months when the motherboard had to be replaced. About 3 months ago, I started to get various error codes and a continuous beeping. An authorized Dacor service repairman has replaced the motherboard three times. He was on the phone each time with Dacor, however we still get the error codes and Dacor has told the service repairman that they are stumped and dont know how to fix it.Here I am, having a beautiful expensive oven to look at but was unable to cook a turkey for my family yesterday! It seems that there is a major error in this oven, and I am stuck with a huge repair bill and an oven that does not work. I can only hope that Dacor will step up to the plate and come up with a solution or replace the oven which obviously is a lemon.

We purchased our range (Dacor Dual Fuel Range RSD30) in about 1997 thinking we had a good investment. We have replaced the bezel 5 times (the area that encloses the control area). Today the door glass has cracked. Whooppee! Merry Christmas! Each time I called about the bezel, I was told that they had a design flaw. The last time we had to replace the bezel and also pay for installation ourselves. We decided if this happened again, we would get rid of it. Well, it will be sooner than later as the oven glass has cracked. Needless to say, we are not return customers.

My Dacor oven (DO130S, S/N V-A-10160044) is less than 18 months old. While it was in use, it popped, sparked, tripped the circuit breaker, and died. I called customer service, and voiced my concern on safety due to potential electrical defect. Steven, the customer service person advised me that this oven is no longer in warranty, and to call a repair service. I reiterated the concern for product safety. He placed me on hold, and the call was dropped. I called again, and Mike answered. I repeated the same info, and he was not willing to listen to any concerns. He hung up on me. This experience does reflect on published Dacors commitment to customer service, or product safety.

Dacor refuses to take responsibility for defects in their products. Our wall oven required two cooling fan motors and two relay boards over a relatively short period of time. In addition, all of the sensors had to be hard wired when the oven stopped working, and our service technician was informed by Dacor that moisture tended to get into the sensors on these ovens. We spent nearly $1500 on these repairs. Reaching a customer care representative at Dacor can take upwards of 20 minutes. Phone calls are not returned. Customers are left to pay the cost of defects in Dacor products.

Dacor dual fuel 30 inch range - First of all the look of the dacor is second to none in my opinion. The digital screen with blue lighting makes this a truly elegant part of any kitchen..... when it works. The range top itself worked flawlessly for me and the main burner was always more than enough. The problem with the range lies in the electronics. The unit has been in my home for over a year and has worked for less than a month total. An error code appeared when ever the oven gets hot. C33, C1, 0000, 1111, C11. Ive seen it all. I have had the main board replaced twice and my local repairman is on first name basis with even my dogs at this point. The final straw for me was when the oven door glass shattered while cooking and when dacor was contacted they said that happens. Im think Ill try Viking.....

We got a Dacor oven and microwave wall mounted Unit 7 model DMT 2420S when we remodeled our kitchen. I have had problems with the microwave with sparking on and off. I have stopped using it as I am worried about a fire.

I wrote yesterday, perhaps a little too hastily that our motherboard was dead on our Dacor stove. The repairman came today and fixed it by removing it from the front of the stove and unplugging two plugs and plugging them back in. Everything works fine now and we are vastly relieved. The repairman commented that most people are very happy with their Dacor appliances and he doesnt repair them very often.Total relief. Also hope this doesnt happen again because though extremely simple to repair, it would become very tiresome to remove the motherboard and fiddle with the sophisticated circuitry if we had to do it ourselves. I wasnt watching real closely what the guy did and dont know if I could do it myself.

Replacement light for the oven - I could not find anyone that carries the halogen bulbs for my oven and called Dacor parts line. The bulbs come in a package of two. They were $79.95. I was told I should have called two months ago, that they were $29.95. So would I buy another Dacor Appliance? I think not.

I purchased a 30 Dacor dual fuel range and matching hood in 2004. I paid $4009 for the range and $948 for the hood. The range and hood have been nothing but problems. I wrote to Dacor in April 2009 detailing the problems with the range with service history dating back to 2006. Problems include overheating when cleaning which is a safety risk, replacement of cooling fan, ignitor assay, part # 92309 membrane, and replacement of relay board in 2007, 2009 and again December of 2011. I attempted to purchase a Dacor extended service agreement in January 2009 but was declined due to the ranges past history and its age. I recently found this site which indicates that other consumers have had similar problems with Dacor products. Dacor has lost me as a customer as I will never buy another Dacor product! I have been disappointed and frustrated with their lack of response and support. I finally purchased a GE service contract which has helped absorb some of the cost of ongoing repairs. The overhead lighting has long since gone out in the hood. I was told the hood needs to be disassembled to replace the lights. Dacor should step up and support its products. When most people put out $4000 for a range, they expect to get a quality product that will last 15-20 years. With Dacor, this has definitely not been the case!

I bought a Dacor dual-fuel range in 2002 for my new house. Within 18 months, the control panel on the front had shorted, causing the stove to emit a continuous beeping. I got this repaired, and was advised that I should not use liquid cleaners on the stove! Two years later, the same thing happened again. Finally, about 4 years ago, another fault developed in the 3rd control panel, the circuit controlling the oven lights will not respond to touch, and the oven lights switch on and off continuously. Not prepared to pay for yet another control panel replacement, I switched off the power to the stove at the main fuse box. I have continued to use the gas cooktop only, lighting it with an ignition wand. The Dacor stove is only part-functional due to what is obviously a severe design fault in the front touch control panel, which causes the panel to short. I switch on the power to the unit twice a year to use the oven at Thanksgiving and Christmas for large roasts. This stove was a very expensive mistake. Luckily, I have a second (Wolf) oven in my kitchen, which I use instead for everyday cooking.

I purchase a home with a Dacor double oven. Unfortunately the oven begins transmitting multiple beeps and the touch panel will sometimes read off after beeping a while. I contacted the staff at Dacor requesting a service manual. They refused to send me a service manual and stated that only authorized technicians can service their equipment. Its obvious they used google or a local phone book and sent me contacts of appliance repair shops in my area.When I called, they had never heard of Dacor let alone be factory authorized. I called Appliance repair shops up to 50 miles away to find there were no Dacor Dealers. I found one 70 miles away but it was too far to send a technician. If I remove my oven from the wall and take it there they would attempt to look at it. I had to reverse engineer the thing to find that my touch panel has gone bad and now I cannot find a used one. I want to recommend that anyone considering an appliance DO NOT PURCHASE A DACOR! If you are looking for high end stick to SubZero / Wolf. Oddly enough I see that there hasnt been any reviews for the past 5 years. Maybe it appears people have stopped buying Dacor appliances.

Front bevel of my first rsd30 range purchased in California in 1999 cracked within nine months. Dacor said it was a defect in the design and would fix it for free. I sold the house in 2001 but the range was still not fixed. I moved to Nevada and bought a new rsd30 range and same thing happened within six months. It took a year to get it fixed at their expense. This bevel also cracked again for the second time in March 2011. Their response to this was to offer me a new bevel for $180 and I would have to pay for the installation. I declined the offer. The bevel is still cracked at this time. At the same time, I bought a PMOR30 over the range microwave and the front handle broke at least four times. And finally, the whole thing broke down and was not repairable. In Aug. 2008, I contacted Dacor and they agreed to replace it with a new DMT2420 over the counter microwave for half the price ($390). Last week, this one blew up on me. Sparks were coming out through the side and a big hole in the removable shield and burn damage to the wall of the unit. I do not believe this unit is repairable. I contacted Michael at Dacor. He apologized and said that theres nothing they can do about it as it is out of warranty but they will look into it. What I want at this point is my money back that I paid for ($390) and for them to pick up the unit and get it out of my house. I will never buy another Dacor product again.

We purchased a Dacor wall oven to replace a GE oven that was outdated. We thought we were getting a premium appliance, but after less than a year and just before the holidays it quit with a code on the control panel we couldnt find in the owners manual. We had a serviceman out and the cost of the part and the service call was more than we paid for the oven! It now sits there, useless and a reminder to never buy Dacor anything!

We bought the Dacor Wall Oven (ECS136SCH) in 2006 during a complete kitchen remodel. In 2009, the relay board was replaced twice. The first time, it was over $500 to replace. The second time, it was covered under the parts warranty when a terminal was bad. Now, I need another relay board and a new element which will cost over $700 to replace. For an oven that was originally over $3000, this is not acceptable, but what other choice do I have? The technician told me that Dacor has the worst mark up for replacement parts. I thought I had done my research and found that Dacor had a good product. I guess I was wrong.

This is our second Dacor wall oven. It is approximately 6 yrs old. December 22/14, I was cooking a Christmas turkey as per usual, and I noticed an odd smell about 40 mins. into cooking. Checking the turkey, the temp. was at 500 degrees and on broil. I burned holes in my oven mitts on the roaster taking it out. Even though I set the temp. at 325 convection roast, it reset itself to 500 broil. Nothing works except the clock. Called repair guy after the holidays. Said it is a control panel behind the keypad area. Ordered the part. Been waiting 4 months now for this part. Now, no Easter dinner either. After reading these complaints, I am worried that this part replacement may not be the end of it.

The Dacor ‘duel fuel’ ranger was $5,500, We have propone, and Dacor’s set up is for natural gas, so all the pots and pans got lots of dark residual. I wrote and called them many times, to no avail. Terrible customer service. Then the F1 error keeps beeping, non-stop. What a piece of junk. Non-stop issues. No service whatsoever from the manufacturer.

The Discovery Model 30 electric wall oven - After 6 years, the oven failed. The fan motor went out and at the same time, we were advised by a very reputable appliance repair recommended by Dacor that we need to also replace the computer or brain. Total cost of repair: $1150 with a warranty of one year.

We moved in our new home in June 2019. We had purchased 2 Dacor dishwashers, 2 ovens, a gas cooktop and a microwave. All the appliances are beautiful. That said, both of our dishwashers leaked so bad we had to stop using them as they were damaging our wood cabinets and floor. Dacor sent service persons out after multiple calls and replaced the seals, but they still leaked. Our cabinet company that sold the Dacor appliances stepped up and replaced them both with Bosch dishwashers.Our Dacor Refrigerator went out in mid February and will not cool anymore. After 2 hours on the phone with a Dacor representative, we finally were able to schedule a service person to come out a week later (Dacor has very few support companies so dont plan on anything happening too soon when there is a problem). Was not able to repair the fridge and said it could be another two weeks to get the part and return. That said our service person is a great guy and cares, but has to rely and wait on Dacor for responses and parts.Our ovens take twice as long to cook as any other oven we have ever had. We are asking them to look into that as well. Overall, very disappointed. We understand having problems, but expect Dacor customer service would be much better and support their own field service persons and clients or at least act like they care. Not looking forward to calling them back to see why we need to be without a fridge for 3-4 weeks total....

I purchased a 48 Dacor Epicure stove in October 2010. We moved into our home in November just in time for Thanksgiving. We remodeled the kitchen and the stove is the focal point. When I heated the two ovens, the pre-heat mode stayed on but the ovens went to 600 degrees plus. My oven thermometers only read to 600. That happens every time and the fans stay on for hours. After many service calls, we have determined that the oven is going into a cleaning mode every time and is wired backwards. Dacor is ignoring me.

We chose DACOR (8-burner double oven top of the line ERD60S06CH/LP) in 2006, new construction because we disliked the signature blue interior of another luxury brand. Last October I detected a gas leak from one of the burners. The authorized repair company was contacted, and the entire unit - all 8 burners and both ovens were out of commission while we waited for the replacement part. Six weeks later the repair guy returned with the wrong part. We had to wait an additional month for the repair guy to return. Apparently, not important that people might want to cook and bake before the Holidays! After the new valve was replaced the oven light began to turn on when any of the gas valves on the defective side was turned on. I write this review 8 months into the problem. I can fix for $700 by ordering a new control panel. I wish I had read these reviews earlier. I overheard the tech say that there was electrical interference and that the wires need to be insulated to stop the oven light from turning on and off. I am so FED up with both the Dacor California head office not caring and the horrible authorized service company. I will take this unit apart myself and fix it. DACOR IS GARBAGE. Go with Sub-Zero, Miele and forget this Brand. DACOR: Dont Accept Crap Or Rubbish! Made in America? Shame on you. No problems with 4 Sub-Zero fridges, or 4 Miele dishwasher the same age.

Purchased a Dacor Epicure ER36DSCH/NG RANGE and oven in 2007. Sad story, it never worked properly since day 1. Initially a gas burner did not light, they came and repaired it. Subsequently the door lock failed in the lock position - had that repaired. The door lock failed the next year again, this time thanksgiving, ruined the dinner. They fixed it but the following year the lower burner element failed at Thanksgiving. All my relatives know not to purchase a Dacor product. Problem is I am stuck with this boat anchor. The oven door motor has failed 3 more times and thankfully the service man showed me how to change it. Today we tried to bake some apple pies and found the oven temperature set at 450 was only 350 (bought an oven thermometer). This explains why it always takes so long to bake things. A complete piece of **, never ever buy one.

Years ago I purchased the Dacor Double Oven over a Thermador because the Thermador had a ridiculously long pre-heat time. The Dacor has performed reasonably well as a oven particularly in convection-bake mode. But over time, components started failing and repair parts were hard to find, unavailable or ridiculously overpriced. I am an an engineer with DIY skills honed from years working with high tech food manufacturing equipment and controls including ovens. In recent years, I have needed to replace a relay board, the main control board, hinges two times, and most recently the hinge receptacles. I have also replaced an inner panel on a door assembly. Just think what such repairs would have cost for an average consumer. I understand the parts can fail, but Dacor has shown little regard for consumers in my opinion. They have done very little to maintain an inventory of repair parts. Basically their message is that the part is now obsolete and unavailable. Thats some answer when the price of a new double oven is multiple thousands. Recently, the hinges on my upper oven failed again. As they failed, their failure caused increased wear on the hinge receptacles. Soon the receptacles failed as well. I was able to find hinges at a ridiculously high price but the receptacles were unavailable anywhere. I contacted a several parts suppliers who told me that they had no idea when the parts would be available. Moreover at least two of the suppliers mentioned that they had a backlog of orders for the receptacles - one had a backlog of over thirty. Yikes!. At that point I contacted Dacor customer service and asked what could I do to get the part. Answer: The part is unavailable and we have no estimate on when it will be available. I tried to escalate my request and got nowhere. Finally after many hours of online searching, I found one set of the hinge receptacles at a price 4X last years price. Lastly as I replaced the receptacles today, I realized that the mounting screws only hold one portion of the U shaped mount. If the screws were longer, the receptacle would be less prone to twisting and wear. Be aware that Dacor was sold to Samsung a few years back. Based on my experience, I could never recommend Dacor. Caveat Emptor!

Bought the DACOR WALL OVEN in late 2019. Top burner is over heating and burns everything, caused a fire in the oven. Can not even get any response from customer service. Warranty not worth the paper it is printed on. Stay away from DACOR.

When I pay top-dollars for a supposedly high-end product, I would expect performance and durability. That is not the case with Dacor. This manufacturer charges top-dollars for their appliances but their products do not live up to expectations. I purchased a Dacor gas cooktop range, and within a year several blue-indicator lights on the knobs (which indicate the gas is on) failed. At that time it was covered under warranty, and even then it was a hassle to get the repair technician to come out and take the range out to get to the electronic parts. After replacing two of the lights, the other lights failed as well, and then the replaced lights eventually went out. Now, only one out of the five lights work. After a year, the appliance is no longer under warranty, and it is too expensive to get it serviced. Its not only a cosmetic issue, but a safety one as well.Were in the market for a single wall-oven, and I considered a Dacor for its clean and stylish design. However, after reading the reviews about Dacor, Im veering away from this company. Sadly, as much as I want to support a Made in America company, the pride of workmanship and customer service doesnt live up to this companys branding.

Oh how I wish I never bought a Dacor! It has been nothing but problems. I figured I bought a lemon but after reading other reviews its just not a good product with not very good customer service either. I have had repairs every year, and even after repairs it still isnt functioning as it should. The first problem I had was the whole glass window blew out during baking, which seems to me is a huge liability. The company said that shouldnt happen but is out of warranty and would give me a discount on the glass. I thought that was better than nothing but then 6 months later the relay went out, then baking temps were all over the place in the oven so they said I needed a new motherboard and they said both ovens needed it. So those were repaired. Oh ya and the light in the bigger oven hasnt worked past the first year even after having the light changed and some electrical stuff done on it. Then I had the bulbs changed due to irregular oven temps. The temps are still all over the place to this day.The back right corner gets too dark. The front left doesnt brown and is a lower temp. Now Im having problems with the oven turning off during baking and when using broil in the small oven it causes the large ovens probe alarm to go on and offer at least for an hour. Dacor didnt help me with anything past the glass and its only been 7 months since the new motherboards were put in. I cant afford to buy a new oven at this time and so I only use the small oven mainly since the larger has so many problems. Do yourself a favor and never buy a Dacor!

We bought our Dacor 30” gas range in September of last year. We were tired of cheap stoves that lasted 5 years before they needed to be relegated to a landfill. We thought it was an investment that would provide us with a reliable appliance and worst case scenario, better warranty repair service than Home Depot or other big box store.After 15 months, the igniter for the oven stopped working. We tried the 800 number on the warranty registration website and no one there could bring up our registration, even though I could see it on the website. They gave me an email address to contact the people who could look it up and I heard nothing for two days. I called the 800 number again and they transferred me to another number and they finally found our warranty registration and issued a ticket for the repair.The company they use for warranty work in Toronto, is Home Appliance Repair GTA and they are absolutely horrible. They said they ordered the part on November 27, but they did not actually order it until December 6th. Dacor then sent the wrong part! I demanded that they send the proper part overnight and on December 13th they called and left a voicemail saying that the part would be here by today at the latest.It did not arrive and this evening I emailed them again and their response was that the part would be here on December 19th. How does it take a week in this day and age to deliver anything? I don’t believe that I will even have a functional oven for Christmas this year. I have already given up on any baking getting done. I will never buy a Dacor product again. I actually really love my stove, but I am beyond disappointed with their warranty service and customer care.

I purchased a Dacor Double Oven 5 years ago. It is a beautiful design, but unfortunately a piece of junk. Over the 5 years I have had the oven, I have had service technicians repair the oven on 7 different occasions. Unfortunately, my oven is not out of warranty and has failed once again. Today was my 8th attempt at service and the service technician could not get the oven working. I have called Dacor, pleading with them to stand behind their product and to replace this useless piece of equipment. I continue to get L22 error codes, and the main circuit board had been replaced twice. After persistently calling Dacor’s customer service, they finally said they would sell me a new oven at a discounted price to the tune of $4800 plus tax, shipping and installation. I ask myself, why would I want to buy another piece of junk? If Dacor wont stand behind their products, perhaps someone should initiate a class action suit against them.

I purchased entire kitchen of Dacor appliances - $30,000. The 48 refrigerator required 9 service calls to stop freeze up. Wall oven – the digital panel went bad. Stove top exhaust – the circuit is melting. The dishwasher had 17 service calls over 2 years - mid way they replaced the unit because they could not stop it from leaking and damaging our wood floors. The most recent service call was yesterday, 12/20/2011. After waiting since November, it is again not working. Does anyone else understand that spending $1700 on a dishwasher should allow you to use the dishwasher? I called the customer service and was told We are discussing the situation and will get back to you. Are you going to come wash dishes with me over Christmas when we have 25 guests? Were you there on Thanksgiving? If I hadnt been stupid enough to buy all Dacor appliances, I would throw it in the dumpster and buy a GE from Home Depot.

Wow! I wish I had read this website before we built our house 3 years ago. I have a 5 burner Dacor cook-top that has been nothing but trouble since day one! I have 5 different appliance brands in my kitchen and the Dacor is the only one that has caused continuous problems. I was so mad at the repair man today I hung up on him (poor guy, I see now Dacor is the problem). The cook-top has exploded three times. ow when I say exploded, I am not joking at all. I mean the explosion blew the cook-top up and burners off, blew the cabinet doors underneath open, flames shot out and the house shook. One of the times, my one year old son was standing next to it. I was so upset I ran into the other room with him and sat on the floor and we both cried. It was terrifying! I have had a repair man here 6 times over the last 5-ish weeks (Yes, I didnt have a stove over Thanksgiving and I was the host; its not looking good for Christmas either and we have 4 kids). They have replaced, cleaned and fixed everything possible. They then pointed the finger numerous times at the propane company (which they now have determined it is not a propane problem for sure). Today the repair company called me (by the way, they have been constant contact with their Decor rep Rob about the problems) and said they are done. My expensive 3 year old cook top is not repairable. They have exhausted every possibility. They have been here 6 times and the propane company three times. I have a hole in my granite counter top cut specifically for the cook-top and am told that every cook-top is a different size so I do not know what I am going to do. I called Dacor today and asked to speak to someone who could help me to no avail. I then asked for someone (anyone) to call me back today. You guessed it. Theres been no call back. This is getting really old. How many weeks does this need to go on (dont answer that)? Another problem that I have just lived with is that the stove continually clicks for quite a while after you are cooking. I was told to clean it a certain way. I did that and it didnt work. The repair man did it; it didnt work. The repair man said something was loose inside and tightened it. It still didnt work. I guess I could live with the click. It is the explosions that I need fixed.

The ovens needs a new latch kit and a mew control panel every year. It has been repaired 15 times. So many issues but those are the most consistent problem areas. Dacor should have replaced our range the first year. Even the repairman says everyone has had the same issues. For what I have paid in repairs I could have bought a new range.

I purchased my Dacor range in 07. After running the self clean cycle today, my oven wont heat up using convection or regular bake. Keep in mind, I had the entire electronic guts of the oven replaced in March 2011, 6 months ago after the same full failure. I paid $6,500 for this appliance. I wish I had my old GE oven back. This piece of equipment is only 4 years old. My husband and I dont use the oven often. What a huge disappointment! I will likely spend the next few days on the phone with customer service.

I would never buy another Dacor product. The microwave totally crashed and now the oven will not heat. I have had contact in the past regarding repairs and they are outrageous. I plan to replace both items rather than paying unreasonable costs. Very unhappy.

Updated on 06/14/2021: We placed a review about a month ago about a defective range. The company contacted us, took some information, but we have not heard from them since. It seems they just wanted an appearance of willingness to help but do not intend to help. After spending almost $4000 on a stove you would think it would last more than a few years before the motherboard malfunctioned. Dacor has provided no help. Very poor customer service and an extreme disappointment.Original Review: We bought our Dacor range for 3800$ in 2017. The self clean function did not work due to a defective locking mechanism. We had that repaired. Starting in 2019, the bake cycle was not heating up to set temperature. We followed recalibrate instructions. Then, the temperature went over the desired setting. I’ve tried adjusting baking times to deal with the problem. Convection bake started having temperatures above the set temperature.Several months ago we called for repair. The service technician tested the sensor and said it was fine. He stated that it was the motherboard which would cost $1200 to replace with parts and labor. That’s a lot of money to put into a high end stove that cost $3800 to begin with and is only 3 years old! We’ve had Frigidaire stoves that lasted 15+ years. This continues to be a problem. Unfortunately, we may have to replace this stove with Viking or Wolf. This is totally unacceptable considering the initial cost of the stove and the fact that Dacor markets their products to be long lasting and reliable. Never will I buy Dacor products again.

We own 3 Dacor appliances, gas cooktop, microwave & built in oven. From the day of installation of wall oven there was a problem. Without going into detail suffice to say it was repaired 3 times within several months, under warranty. We were having issues with our microwave not working consistently, after several service visits, not under warranty, we now are told it will cost over $600 for the part. We are now looking for another brand of microwave instead of fixing the Dacor. On a side note the rings for our Dacor gas cooktop never come clean no matter how hard you try. The material used are definitely inferior. We have another property with all KitchenAid and have been happy with the performance. Our fridge & dishwasher are KitchenAid and I regret not getting the same brand for our other appliances. If I could give a minus star for Dacor I most certainly would do so.

I have all Dacor Appliances in my kitchen and I am very disappointed and angry. The double wall oven has not worked since day one - cant roast a chicken or God forbid, I would want to roast a turkey for Thanksgiving. The ovens look great, but just wont cook anything. Raw on one side and burnt on the other. One time I roasted a 5lbs leg of lamb for 5 hours! It still wasnt cooked. Recently, my dishwasher has stopped working properly, stops midway through cycle, wont drain water and its just been a total waste of money. I will never recommend Dacor to anyone. Do not buy Dacor. I called customer service in the beginning, as we had problems from day one, but they were of no help so I gave up. I dont use my ovens anymore, they are just for display. Very, very shameful!

I purchased a single wall oven in 2008 and 30 days out of warranty, the oven broke. Service required two service calls to fix the door magnets. A third visit was required as the oven codes shut down the unit. The last two service calls have been with the cooling fan. Now that the fan was replaced, the relay board needs replacement, too. I have spent $650 in service alone, which is separate from the cost of parts. There’s no help from customer service; in fact, the rep was downright rude. I will never purchase this brand again and I have told anyone who will listen not to purchase.

I was a bit anxious when I purchased my Dacor range because I really didn’t know how it would perform. A year later and I couldn’t be happier. I love my Dacor 30” range. It has been one of the best purchases ever.