Our Profile over-the-range microwave failed after 2 years. (Warranty was for one year!) One day it suddenly died. The repairman ($100) said repeated twisting of the wire from the oven to the door (which contains all the electronics) is inevitable with opening and closing. The wire often breaks within its insulation: a bad design fault. No question of replacing the wire; we would have to order a new door, for nearly $400 plus $200 for installation, which requires 2 service technicians. This is more than the cost of a new OTR microwave. He advised us to get one with the controls beside, not in the door. Unfortunately GE is the only company that makes a microwave in the same colour as our range.

I have microwaved many types of food in mine! Remember, it’s not just for reheating leftovers! I have cooked fish, and chicken successfully. Those turned out juicy and tender. I follow directions from a microwave cookbook. It’s easy and clean up is a snap.

Wow, Donna from NJ, I could have written your dishwasher report! But since I didnt, I have never been so disappointed in an appliance purchase as my new GE dishwasher! Not only are some of the dishes & silverware coming out more dirty than they went in, it takes a ridiculously long time for a cycle. And if there are more than a couple of tablespoons of water on the door, it will pee out onto the floor when the door is closed! Not to mention that there is junk stuck to the floor just inside dishwasher, under the door, after the cycle has run! Yet the worst part is how dirty dishes are after even a Sani Wash cycle! Sometimes, the detergent lid is still closed. Sometimes its open, but the detergent is still there. Even then, dishes may be cleaner in appearance that time, than when the detergent is gone. A water glass, may have gritty stuff - not just detergent stuck and hiding down inside, or more obvious all over inside the glass. I have spent the past year experimenting with various things: detergents, amounts of detergents, arrangements of dishes, heat of water, pressure of water, rinsing dishes before cycle, etc. Glass and pottery normally fare better than plastics, but again the plastic may have started cleaner than they come out! The dealer has been out three times, finding nothing obvious the DW itself, nor anything I have done wrong. He has been told there is a kit that would fix the performance problem, but he cant purchase it, nor can his distributor. I have been told the length of cycle is because our government regulates the amount of water used. So my question is, then its okay to use more electricity?! Its totally embarrassing to serve someone a drink in a glass that is found not clean near the end of the drink! And I, too, have an old 12-years-dishwasher that still works! It was even a cheaper brand. I never had to think where pieces were arranged in that dishwasher. I just thought, in my newly built house, I should have new appliances!

My less than a year old GE microwave stopped working last week. My AT&T phone service died so I had to make repair arrangements online. Guy was here this morning. My microwave’s main board is fried. It does not conform to Repair Guy’s published schematics. Repair Tech could not upload new data to it. Repair guy did order three new parts including a main board. GE told Repair Guy that mainboard delivery ETA UNKNOWN. After three hours here repair tech left and told me to call GE customer care. Believe it or not, two hours on telephone with GE. First you need to talk to a customer service rep that cannot help you. They then determine you need a Customer Advocate. Then they need to input data on your file for the Customer Advocate.Then they need to transfer you to that department. Then you have to get a case number assigned. Then you give someone all the serial numbers and model numbers again. Then the Customer Advocate (CA) takes the call. The CA does not speak English as you and I speak English. After the CA puts me on hold to verify the purchase, then the appointment, then the tech and then the order they actually speak to me. In my case, the mainboard part is not available on CA’s computer. The CA has to electronically contact the parts department to find out if the part is in this universe. If the part can be delivered to my Repair Guy in Jackson, GA within 14 BUSINESS days from the date of the inquiry I have to take the part and wait for repair.In the event the part cannot be delivered in 14 days CA will start a process to get me a new microwave. The parts department has up to 48 hours to respond to the CA. When asked what happens if no response occurs in 48 hours, I was told, That never happens. It is the Christmas Holiday and I anticipated guests. My husband is disabled and his meals are pre-made frozen so I will have to decompose them and heat them on the cooktop. GE could care less about those issues. So after waiting five days for repair I have no working microwave. Someone told me not to replace my GE with a GE, but I did not listen. It is December, holidays, no microwave is an aggravation that I thought paying for a GE product would alleviate. So, on January 2nd I might get an answer. Part possible or new appliance COULD be ordered and delivered by someone sometime.

Its been a decent dishwasher. Usually residue left on something. Even with rinsing. And weve tried all brands of detergent. Rinse, China, speed cycle, normal, pots/pans and anti-bacteria cycles. 9 hour delay and extra hot wash and heat dry settings. It works for our family. A load every 2 days or so. Its almond/bone colour. The hoses are flimsy. They seem like they could leak at any moment. Not sure Id buy another GE.

Bought the unit about 2 years ago. The interior paint started coming off after about 1 year and several months. At 2 years, the unit stopped working and is reporting a shorted keyboard. I have had other over-the-counter microwaves that lasted over 12 years and were replaced just due to old age and style. I have read about others with the exact same issues. Ill stay away from GE products big time after this display of poor reliability.

GE DE68 00307A microwave was bought in June of 2011. Last weekend, August 25, I was heating water and the microwave started smoking and then failed. The entire apartment was filled with chemical smelling smoke. I have a parrot and had to get her out immediately as this type of smoke is highly toxic. I had to keep her out all night long.

In January 2013, my husband and I purchased new appliances from Home Depot, including the above referenced dishwasher. The first dishwasher was delivered broken. The display panel was detached from the body of the dishwasher. At that point, I was concerned about the quality of the product. From the way it was detached, it appeared to be very cheaply made. (It was also installed incorrectly, causing a leak under our sink and ruining the bottom of our cabinetry. We settled this with Home Depot, but I include this detail to help emphasize my frustration over this whole situation.)When I contacted Home Depot about the faulty product, they agreed to provide a replacement, so I decided to give it another try. I wish now that I had simply returned the product and purchased another brand. Upon receiving the new dishwasher, I noticed immediately that the edge of the inner rack was scratched so badly that the plastic coating was gone, and rust had already begun to appear. I had to call customer service and get replacement racks. (More on this to follow.) Allow me to detail our service call records:Call #1. Heat dry didnt work at all. The technician told me that I needed to run the water in the sink and make sure it was very hot before running the dishwasher, and he changed the settings. This created a slight improvement, but not much.Call #2. Soon after, detergent tabs started to get stuck in the dispenser cups. I was using the exact brand recommended in the manual. The technician told me that detergent tabs were just the worst, and that I should try gel detergent, even though this is contrary to what the manual states. The detergent ruined my silverware, and I have had to purchase a new set, which I now hand wash.Call #3. Using gel detergent did not work. Technician came back, and told me the wrong replacement racks were sent. That must be what was blocking the water from getting to the soap. He ordered another replacement rack. He brought a plastic door, watched the water, and told me the upper arm wasnt spinning fast enough. He made an adjustment and claimed to fix that.Call #4. Detergent still not emptying from the cup. A different technician came back and used the plastic door. He found a different problem, but did not have the parts to fix it, so, another service call had to be scheduled.Call #5. Technician comes back, and finally fixes the detergent cup problem. For now.Call #6. Heat dry now does not work at all. There is so much water on the dishes that I have to hand dry them, and afterward, I have to mop my floor. There is just a massive amount of water in the dishwasher. In addition, it will not start except on a one-hour delay. Pushing the delay button does nothing to change the settings, and does not allow me to scroll through like it should. This appointment is scheduled for today, but I am not hopeful that anything will change.At this point, I have no faith that this dishwasher will ever work. Customer service did extend my warranty for six months, but that is the only concession I have gotten from them. That extension will expire soon, and I fear that at that point I will simply have to spend another $600 on a new dishwasher and leave this one on the curb. Its unacceptable for any consumer to have to purchase a new dishwasher less than two years after purchasing from GE.

We moved into a new home in June of 2011 with the appliances already included. Ours came equipped with a GE, over-the-range microwave, model JVM1540DP1WW, manufactured in Malaysia, in April of 2010. Within several months, the revolving platter began to make a bumping noise while turning and then it eventually quit turning altogether. Five service calls later, we had the platter motor replaced, circuit board and four fan motors (apparently the platter has voltage supplied from that fan to make it run) and it still didnt work.It was taken back to the shop and eventually the problem was traced to a loose wire on a terminal connector. After a month of operation, it is again beginning to make the bumping noise while the platter turns. To top it off, Consumer Reports (the March issue) deals with problematic microwaves, especially the GE model and the unexpected fires that can occur. In addition, they can be susceptible to (not always however and only on certain models) wireless transmissions which could potentially cause them to start on their own. I know for a fact that it knocks off my XM Satellite Radio when it is running. Bottom line...its history and will be replaced with a check rated appliance before I too have a major problem.

I have had my GE microwave for over 6 years and the paint is flaking off the inside of the microwave, causing a health and fire hazard. Paint chips in the food and bare metal exposed can cause arching which in turn can be a potential fire hazard. After researching online I have found that this is not a uncommon problem with GE microwaves. Some have had this issue after 1 year. I contacted GE and told them of the problem and that I felt this was a manufactures defect.GE does not feel that this is a defect problem but advised me not to use the microwave any longer. Their solution was to discard this microwave and purchase a new one. I paid almost $300.00 for the original one plus $20.00 for a mounting kit. I was told that GE would offer me a discount on a new one from $339.93 to $319.93 total. This is not much of a offer considering this should be a obvious manufacturers defect. By ordering another I will have the same problem again. GE needs to stand by their products and admit fault.

I purchased a GE Microwave Oven model # JES1139WL03 in late May of 2010. In early July, the paint started coming off the inside of the door when I wiped it with a damp dishcloth. I called Lowes, where I had purchased it, but was told that their warranty was only 30 days. I called GEs Consumer Support line and was told that for $65, I could ship the microwave to a repair center who would determine whether the machine could be repainted or would need to be replaced. I was told that either would require me to pay for it, since the machine still worked and peeling paint was not considered to be a warranty item. I guess if it catches fire, then they might warranty it.

We purchased this dishwasher for our rental. The last dishwasher was over 30 years old and still working but the racks were coming apart so we opted for a new one from Home Depot. A year later our tenants called saying when they used the dishwasher it rained in the basement. Our maintenance man called and said the dishwasher melted a hole in the right side about 1.5 inches by a 1/4 inch. Midway to the heater element. He did a temp fix with silicone.I called GE Recall number and was told it was not on a recall list. I called customer service and was told they would waive the service call. I explained this was a FIRE HAZARD. They insisted all they could do is send their tech out for repair. Since I paid about 280 dollars for the dishwasher I decide a service call would probably run near that and told them NO! I am now sending all information to consumer affairs department with my STATE REPRESENTATIVE. I also am putting the fire hazard info out there on facebook and twitter. I am waiting for someone else to say they also had a fire hazard. This should be on a recall list!

Our GE microwave, manufactured in 2012, has been running fine, but the door handle has cracked on the bottom. Imagine my shock when I found the cheapest price for a PLASTIC handle was well over $100. How can this be?

JVM1540 - We replaced the microwave that came with our home above the stove. When we took the old one out, the blower was not installed properly for ventless. We thought that had to be the reason it just stopped working. We felt sure it wasnt GEs fault as we have always trusted them for a quality product worth the price. WRONG! I cant help but wonder if Lowes knows they are selling a costly piece of junk! When our new one quit working, we replaced the fuse 3 times, now it says keyboard is shorted service required. And thanks to this site I am tossing this piece of junk without spending any more money. GE shame on you!

My dishwasher is very quiet and effective in its use. I am very pleased with my unit as I saves water and power when in use. It also cleans very well and smells good as it drains completely. General Electric is very reliable and outstanding company and is made in the USA.

I bought this microwave about 2 years ago (2011). Yesterday the microwave turned on by itself, I tried to stop it by hitting the clear button that didnt work so I had to unplug it. When I plugged it back in it seemed ok so I reset the clock but within minutes it started again, this time the key pad read key pad short-circuit and then went blank. I am glad I was home when it happened. I am now wondering if I should repair it or replace it.

This is the second digital microwave I have owned. Both of them have been GE brand. There is nothing fancy about them but they are very Easy to use and get the job done. The first unit lasted about 15 years before it had to be replaced. It was used almost on a daily basis, so I feel I got my money’s worth from the unit!

Have used GE dishwashers before - were good. However GE no longer makes them, its just a name - now made by MABE (part of HAIER), Mexican with Chinese ownership, and this new one arrived with a factory fault - cracked tub which leaked immediately. Cracked tub seam and leak found immediately by service tech GEs site referred. Good news is the leak detector worked! Bad news - is we didnt install it right away (old one still worked and pandemic...) so it was a year before we got to it (was partly a gift). So - now MFR Mabe is giving us the run around and so far not doing anything about the faulty dishwasher they mfd and shipped through Home Depot. Dont be fooled as we were - GE is not actually GE anymore and the mfr HAIER/MABE are doing nothing to correct a factory mfg fault.

My parents owned the same GE microwave for over 25 years and had no problems with it. However, after theirs finally died 2-3 years ago, my parents made the mistake of purchasing another GE microwave. BIG MISTAKE!!! It wont turn off unless they unplugging it! They have already paid to have a tech come out to fix it but the problem started again 3 months later. I called 1800GECARES and they said you either need to have a tech come out or we can replace it. I said Do you mean your solution is that my parents who just spent several hundreds of dollars on your defective appliance should spend several more hundreds of dollars to purchase another one from GE? Why did their last one last over 25 years but this one only lasted around 2-3 years? Why dont you stand by your products? Their response was I can connect you to customer service for further help. I said I think Im going to stop wasting my time. and hung up on them. Dont trust the GE name, it doesnt mean what it used to!!!

I bought this replacement dishwasher based on its energy efficiency rating and recommendation of the salesman. Worst dishwasher I have ever had by far (in 27 years)! Salesman didnt know it doesnt have a water heater. It worked so poorly I had a company repairman to look at the dishwasher within a week of delivery. He recommended we run the sink water until boiling before turning it on, always use normal power, steam and boost settings. The cutlery is still often dirty - you have to scrub all food off the cutlery and rinse until clean before putting it into the dishwasher. A year later, the dishwasher is not nearly as quiet and a cycle takes 4 hours. Because of the design, this machine loads quite a bit less than my old dishwasher. Overall, I am sure this dishwasher uses way more energy and I use more cycles per week. I wouldnt take this dishwasher if they were giving them away for free!

The dishwasher is poor quality. Top is thin, top dish rack has trouble with tall glasses. Bottom rack doesnt slide in and out well. The power cord and water cords are too short. They are 2 ft shorter than our previous model dishwasher. Top was loose when delivered and had the wrong screw in one of the holes. The hose and cords are difficult to hook up because they are so short. We cant fit as many dishes in as our previous model of the same size and the unbiased reviewers are saying its washing quality is poor. We havent had it long and hate it. Home Depot wont take returns on portable dishwashers though. Out lots of money on this. This GE is thin plastic trash that costs lots of money with no return.

I have a newer (one-year-old) but base model GE microwave. I wasnt interested in lots of features, like convection cooking and such. I only use it to reheat coffee, occasionally heat a frozen meal, etc. It functions as designed, and Im very happy with it.

My experience with GE over range microwave oven (built in) as follows/ Unit Mod.JVM3160RF3SS. Ser.#GG248367A, this unit was produced April 2016. Review February 28, 2019, unit began to disconnect itself during normal use. This was done by way of throwing 15 amp breaker. New home with dedicated circuit = Yes. Online Problem shows indoor sensors interlocks not adjusted properly. Troubleshoot fee minimum $99 with parts estimate $250.00. We have been limping along for two months with frequent trips to basement resetting breaker, now the breaker trips when activated. Same thing happens on multiple circuits, via extension cord trial. Next step purchase NEW MICROWAVE that is not GE.

I give it stars for value because an extra step is needed to set cooking time. Most microwaves do not require pressing a cook time key before selecting # of seconds. Other than that, microwave is first-rate and very dependable. We use it several times a day for 1.5 years now with no problems.

I bought this over the range microwave in 2009 to go with my other Cafe appliances (dishwasher and range). After a few months, it stopped working and ge sent a repairman to fix it under warranty. He took it apart, replaced the touchpad panel, but told me that the old panel was still good and that I could keep it for the future in case I needed it. And I did. It stopped working a year ago. I took the whole machine apart, put in the original touchpad, and it worked. Until about a week ago. I went away on the Fourth, and when I returned 3 days later, I had the same problem for the third time. I just called ge service and was told that the replacement for the touchpad is $600. When I started to say that I could buy two Microwaves for that amount, the ge service person cut me off and asked if she could help me with anything else. Rude. In addition to this, the Cafe Range ($3000) has three unusable knobs because they were made of cheap PLASTIC and are cracked.They just spin and turn nothing on. When the third one broke, my wife had turned on the power boil and was unable to turn it off until I came home 2 hrs later. A huge FIRE HAZARD!! To replace the six knobs is, you guessed it, $300. I could buy an inexpensive stove for that. I have purposely used ge in lower letters because that is the way I feel about their appliances and their service.

Purchased a GE profile dishwasher two years ago. It stopped draining. After 4 service calls and $400 we had to buy a new dishwasher. Basically I threw $1000 down the drain. My recommendation is do not buy a GE dishwasher!!!

I bought a GE Profile dishwasher and have the same problems of residue on the dishes. My dishwasher is only 4 months old. I paid top dollar to get the same line as my refridgerator. This dishwasher should clean the dishes sparkling clean for what I paid for it. Disappointed in Cobden

We bought a brand new GE dishwasher from our local hardware store on Black Friday. It was $600 dishwasher on sale. It was installed on December 5th, it broke on December 6th, and we had a repair man come out to take a look at it. To be fair, the local hardware store did ask if we wanted to replace (2 week wait time) or repair (2 day wait time) it. Since it was a bolt that was severed (by opening the door to the machine, mind you), we figured it would be an easy fix. The first technician who visited said, Yeah, its broken. I have to order a new bolt and then come back out in a week to fix it. And oh, by the way, Ill have to drill a new hole for it too. Thats when I called GE customer service to request a new product. But since my 48 hour window had passed, and we opted to have it fixed, it was keep it or ask our local hardware store to replace it at their expense. I bit the bullet and just had it repaired. Now, less than 2 months later, the technician has been at our house three times. He’s soon to have a fourth visit because we need a new dispense modulator. After speaking with customer service several more times, and with a not very nice lady in the Chairmans office, I still have a defective product. Oh, did I mention that Im paid hourly and have now taken off 13 hours? So what’s the use of that $600 dishwasher that we bought? Its been out of commission for more than 2 weeks, in less than 2 months, and has now cost us $900. Thanks, GE! We’re so glad to see you stand behind your product.

We purchased a GE over-the-range microwave oven last November 2010 and it was installed in February 2011 when our addition was finished. Last week, it decided to stop responding to instructions. When the door is closed, it just continues to run--the turntable turns, the light stays on and the fan keeps running. It will respond to instructions, but when we want to shut it off if the door is shut, we have to unplug it--which is a real pain because it is over the range.We have an old microwave that was my wifes parents and it still works fine even though it is about 20 years old. The new one stops working in a little more than a year which is not acceptable. We contacted GE and were told that we would have to pay over $100.00 to get the thing fixed. I dont think so. We will not purchase anything GE again.

I purchased a full suite of GE Monogram Appliances about 5 years ago. All are fine except the microwave which was made in China. The back is rusting out, the inside is chipping at the door and moisture builds up in the door window. This progressive deterioration has taken place over the past 5 years. I paid $420 for the microwave plus $226 for the trim kit. Now, all GE wants to do is sell me a new unit and a new trim kit (will not fit old trim kit). I paid approximately $20,000 for the entire group. I bought GE because I trusted the name. Im stuck with GE if I want to match the remaining appliances. There are only two people living in this house so there is only minimal usage. To further complicate things, there is no serial number on the tag.

My GE dishwasher is just OK, I would say. It saves water and money. It is fairly efficient to load and pretty effective at washing on normal but many times I need to hand wash the big or hardened food off the dishes before loading, which feels like more work than should be necessary. Id rather not wash my dishes twice.

My GE microwave (Model: JVM1540SN1SS) that I bought new two years ago for $250.00 broke already. The table doesnt turn and nothing heats up even though the timer works. There are only two adults in the household using it, and we dont even use it very often. I find this pitiful service. My last microwave lasted about 15 years.

Update 4/14. GE finally conceded that the dishwasher is indeed broken last week, and set up a replacement unit to be delivered and installed. The company that delivered the new unit would not install it of course...why would they? So, we had to hire another place to install it. GE is supposed to reimburse us for the extra installation expense. Im glad it is finally resolved, but man, oh man...what a headache.

I purchased a new GE over the oven microwave to replace a 10-year old Spacemaker unit. After three weeks of use with no issues, the unit overheated excessively during a normal use. The heat was so intense that the pegs that hold the racks melted causing a severe burn on my sons thumb. I unplugged the unit fearing further injuries and/or fire. Are GE products manufactured poorly or did I get a lemon? Who knows? Anyone else have a similar issue? I am still waiting for GE to respond.

We have enjoyed this dishwasher for over 25 years. Over 25 years ago my husband gave me a portable dishwasher for Christmas. About 15 years ago we turned it into a built in. It doesnt look great, some rust and lost 2 of the prongs but it is still doing a great job.

After heating some water in the microwave, I opened the door and removed the water. A few minutes later, I heard a noise and noticed the microwave was running and the control panel indicated it was off. I opened the door it turned off. Closed it and it was on. Smelled something burning electrical in nature. I had to kill the circuit breaker to turn it off. I opened the door and felt the inside of the microwave and it was extremely hot. I was concerned that it could result in a potential fire, I continually checked it until I felt it was cool.

Needed to replace handle. Silver covering started to peel and actually got a splinter. Cheap plastic underneath covering. Called GE and while they did send out a replacement, I had to pay to have it installed. Instructions on internet were not helpful! Bill to replace was $142. Ouch. GE rep said they did not have prior complaints. I later Googled it and saw 1000 complaints!!!

The dishwasher malfunctioned and flooded our home. The dishwasher continued to run even with the door open and the display showing “leak detected”. We had started it before we left the house and it had been running for about 20 minutes when we left. When we came home hours later, hot water was still being produced by the dishwasher and had flooded our kitchen and basement. We could not stop the dishwasher with buttons at that point and had turn off electrical and water supply to it. The absolute worst part is they will not replace or refund it even though it’s less than six months old. They are only offering to service it and expect me to continue using it.

I have had the GE Unitized washer dryer for 4 months with no problems. It has the cycle choices I need for washer and dryer. It's easy to load and remove clothes, even if the washer tub is a little deep. It washes bulky comforters, coats, heavy denim, bathroom rugs just fine. The dryer is big and quiet. It works like a HE but uses all types of detergent. Great buy! Gave 4 stars for function only because all models do not have a "rinse only" choice.

GE Cafe Series dishwasher model # CDW9380N20SS is a fire hazard. Three days ago, our GE Cafe Series dishwasher nearly caused a fire. If I had not been home that day, it surely would have. I ran the dishwasher as usual and went about my day several hours later. I detected a strange acrid smell and with my five-year-old who was ill and at home that day, discovered the dishwasher door was burning hot to the touch. I needed a potholder to open the door. Once opened, there was a blast of heat and smoke. I needed to use oven mitts to protect my hands from the heat to pull the racks out and handle the dishes. The heating element did not deactivate at the end of the cycle.If I had not been at home, the house would have been destroyed as all the plastic items on the top rack in the dishwasher melted. In addition the plastic parts of the lower rack, the wheels and their clips; the silverware holder; covers; the clips that hold the pot tins in place were destroyed, to the point that the majority of our silverware was coated with plastic. The plastic on the lower water dispenser has been demolished; it completely melted more than 50% of the plastic covering on the arm and is charred and burned. We are so lucky to still have a home!The door must be kept open. When the door is closed, the element super heats and presents a major fire hazard. We have noticed that there is a recall for similar models with plastic tubs, but ours has a stainless tub. GE needs to broaden the recall to include all these models. This is a serious issue that needs to be addressed immediately. Our GE Cafe Series dishwasher model #CDW9380N20SS was installed on October 1, 2008. I would not be surprised to find that parts from the recall in April 2008 were also used in the Cafe Series. I have discovered in the few days since the DW units malfunction that there are over 1000 complaints listed with similar, even identical complaints, on multiple internet sites with the same problems.

I was heating up some Mexican food and smelled plastic burning and looked in the microwave and saw one plastic knobs that hold up the metal grill on fire. I blew it out. I have GE repairman come out to see if they could fix it, and he said that happens and they were not responsible for it. I told the repairman to get out of my house as GE has built a product that can burst into flames and will not address that they are at fault.

Dishwasher works fine; however, do not like the interior which is all plastic. It comes with several tray holders which I found awkward to use. I wish it took less time and water to get the dishes done.

I work as a service tech for a major insurance company. I am a master tech, and master electrician. The company that I work for owns an apartment complex which is used to house company executives whose offices are located at other sites, but often come to the Chattanooga Site to work short term. I was called to repair an old dishwasher in one of the apartments. Upon looking at the existing dishwasher, I decided to replace with a new one. I received a new GE model GDF 510 PGD 1WW dishwasher on November 8, 2013. As usual I unpackaged the appliance and examined the exterior. Finding no visible damage, and with the help of a master plumber, I removed the old dishwasher, and installed the new one. After all the connections were made, I opened the door, removed all the packaging from the dishwasher, and found the upper spray arm lying in disarray in the bottom of the machine. Assuming that this was the way that the machine was packaged, I installed the spray arm, plugged the machine up and started the machine as the operations manual instructed. The machine would not work. The power lamp would burn solid for a few seconds and start flashing. I tried to start the machine a number of times while reading the instructions, and while my partner read the instructions aloud, but with no results. Finally, I used a screwdriver to hold the door switch closed, pressed the start button and the unit started. The catch mounted on the door would not make the door switch, mounted on the machine body. We tried to adjust the switch and the catch, but with no success.The dishwasher did not show any signs of exterior shipping damage, but for some reason the upper spray arm was off and lying in the bottom of the unit, I found a small piece of broken plastic and a screw in the bottom of the machine, and the door switch would not make. Outside that I have no complaints. I am not sure where this machine was assembled, but it certainly was not equal to the machine that we removed. Thanks GE for making my job harder. I will have to find another dishwasher Monday and replace the damaged one, and perhaps send this one back, but the replacement will certainly be another brand.

I bought the GE dishwasher in the slate color, just after a colleague at work did - within a few weeks of each other. Hers has already been repaired twice and is still not working. Mine was installed last week - and did not work even one time. No water getting to it. Had the connection checked and installer confirmed the dishwasher was defective. Im sending it back and want nothing more to do with GE products. I wish I had seen/looked for these reviews before I bought it.

I thought that making a purchase of GE products would be a positive experience especially with GE Customer service - should they be needed for resolution of any complaints. Wow... was I wrong! I purchased a GE Microwave (junk), a GE refrigerator (junk & previously submitted a review), a GE Stove (no problem - so far) & a GE Dishwasher (junk) & this review is based on this product. All of the aforementioned GE products were purchased at the same time. The dishwasher began to leak & malfunction. I called GE & they put me through the paces - the beginning of another terrible experience. I was directed by GE & RC Willey to Consumer Electronics who send out a repairman who proceeded to rip me off for 165.00 for a part that didnt work! C.E. denied sending a serviceman to service the dishwasher! I returned to GE for help in getting my dishwasher back in service. The ONLY solution that they offered me was a replacement that I had to purchase! Bottom line the experience cost me close to 675.00!! The Original GE Dishwasher cost me 1,000.00!! GE refused to take the dishwasher back or even give me any type of credit for what I have. What I have now is another GE piece of junk that I had to pay full price for - $550.00 + tax, etc... The washer runs forever - does a terrible job in washing & rinsing & leaves a film & a white powder-like film on the glasses. Ive changed detergents in an effort to get a decent wash out of it & that hasnt worked. I am so sorry that I spent so much money for GEs Top of the Line appliances only to end up frustrated with GE Junk & a Customer Service Department that was just as good as their product. I would NEVER purchase or even think of purchasing another GE product!!! My advice to anyone considering purchasing ANY GE Product is Dont Do It.

Horrible experience. I wouldnt recommend GE appliances to anyone. My husband and I ordered our items on the day of closing on our new Home. Well the items were scheduled to arrive Aug 9, 2017. Every other Appliance arrived from Samsung, but my GE dishwasher was a no show. I received a phone call hours later stating they didnt know it was on Backorder and I wont receive it until Aug 11, 2017.I spoke with supervisor Krista because I didnt understand the lack of respect far as not knowing if the 11 was a good day or even so much as an apology! Until I expressed how upset I was! 2 hours later I received a automatic message stating the items it still on Backorder and now its not coming until Aug 17th! I spoke with Home Depot who apparently has nothing to do with the vendor handling and conducting business this way and now I have to go return the product & order a new product.I dont even want GE appliances AT ALL. After calling today being put on hold 30 mins still no supervisor came to the phone. Terrible Customer service and lack of communication of the vendor. Ill be sure to highly encourage my friends and family to not support this Brand! Feeling upset and totally let down. I know this cant be how such a popular brand conducts business.

Last summer GE replaced the peeling handle on my microwave oven. I have treated the new handle with kid gloves. No abrasive cleaning products have been used and the oven burner under the handle is used infrequently at very lower temperatures. One year later its peeling AGAIN. All the burner control bezels on my GE Cafe oven have also peeled. The handles look like plastic covered with aluminium foil. Cant believe GE hasnt fixed this problem or issued a recall. I will NEVER purchase another products made by GE!

I purchased a new GE washing machine, and a new GE dishwasher, less than 5 years ago. The washing machine started leaking suddenly, and the repairman stated it was due to a cracked basket. They stated this was very rare, but the warranty had expired. The repairs would cost as much as a new machine. The dishwasher stopped draining water. A repairman advised there were two pumps, and one or both may be out. Estimates to repair the unit were only slightly less than the cost of a new unit.I will never again purchase GE appliances. I believe the life of a home appliance should be longer than 5 years. The cheap units I bought in my younger years lasted 20 years, without any problems. The GE units are not quality machines, and repair costs are outrageous. Nice way to try and convince appliance owners to just go buy new units. I can guarantee, I will not buy GE products ever again.

This GE CVM2072SM1SS Microwave (over-range model) worked fine for five years. Then, we discovered the plastic film over the touchscreen starting to peel. After a bit of wrangling with Consumer Relations, they sent me a replacement touchscreen. The LCD didnt display properly, so they sent me another one. It worked for three months, then in the middle of programming to reheat some food, we got the following error message: Control Fault, Shorted touchscreen - F10. The control has detected a shorted touchscreen and has shut off the oven. It may still be possible to use the oven. However, if this message continues to appear, your oven will require service.The only way to clear the message was to unplug the unit. No amount of replugging in cleared the message. I called GE and they said they would replace the entire unit with a new model under some program they had. Sounded fine to me. I left the house. When I returned, I received a message that their representative called back to say they would not replace the unit, since the program had expired. Huh? I called again, and after a bunch more wrangling, they agreed to send a service tech out and replace whatever needed replacing or fixing at no charge. Of course, they never really made a notation of that, so when he got here, he had to get on the phone and sort it out. Finally, he replaced the touchscreen. Lets see how long it lasts this time.

First Profile microwave/oven caught on fire. Was replaced. Front panel on Profile refrigerator not reacting to touch. Repairman said that this model had problems. Fixed it - cost over $100.00. Dishwasher (Profile series) not worth the cost of heating the water to run it. Cleaned dishes by hand. Stove top died - not reacting to touch. $90.00 for repairman to visit us, and another $60.00 to tell us what was wrong. A lot of money for inferior products.

Dishwasher lasted just little over a year when it broke down first time. Power switch made out soft plastic jammed up. Next cheaply made door close switch cracked. Part prices are average price. Because poor quality, I predict replacing this within 3-5 years.

We have a lower end GE stainless steel model that came with the purchase of our new build home. The washer is just average and does not have a huge capacity. For only 2 people in the house it gets the job done in general.

I may be speaking too soon because I need to run my dishwasher again to make sure the minor leak truly has been fixed, but I am very impressed with the responsiveness of GE customer support. There was virtually no wait to talk to a rep about my 2-month-old dishwasher with a drip (plus water was collecting inside). Less than twenty four hours after my call, a friendly man was at my door to fully diagnose and then correct the issue. This was the cheapest, bottom-of-the line model that they so quickly came to service! Now in an ideal world, a new dishwasher wouldnt need any servicing at all, but I think all dishwashers are pretty finicky so at the moment, Im pleased.

Cleans ok but not sure if its detergent or dishwasher but never seems to get all dishes completely clean. It may leave a ring in my tea cup so sometimes Ill have to clean it slightly to make sure it comes off. Basic settings on mine, nothing special. Good for plates and some Pyrex cookware but it would be nice if I could put larger pots in it. Very basic white in color but it is over 10 years old.

My microwave on the inside paint start peeling off. I have this appliance 2 years, it has slowly been peeling since that time and now it has completely peeled and rusted on the inside. This WAS a gift. The outside looks great, the inside is so bad. The serial # is LT914637B model JES1451DN1BB manufactured in 2010, Made in Malaysia. Be Louisville ky 40225. Does the united States make anything except make us pay taxes. This is a piece of mess. The last 2 years my husband he suffered with LLC. Now I got to deal with this. Poor workmanship. I want GE to give me my money for the MW or total replace it. Rate 0.

Bought a PDT845SSJ2SS in June. Two months later, it has a leak. Good news, has a leak detector which shuts down the machine. Bad news is that it leaks and the leak detector worked! Called GE. We dont have an authorized service technician in your area. We will get back to you within 3-5 days. Three days later, after I had raised rain with my appliance dealer, he arranged for a local dealer to come look at the machine. Scheduled that appointment - it was Friday, and We only come to your area on Tuesdays and Thursdays. Next Tuesday is booked, so we will try for Friday. Then, someone from an organization called Platinum Services calls and says GE has assigned the ticket to them. Shes going to try to schedule a diagnostic appointment in the next 7-10 BUSINESS days. Told her to forget it (found out she was calling from Lowes and had to find a technician before she could schedule.) End of week 1. Following week, someone else from GE calls and asks if I was cancelling my service request. In the course of the conversation, she asks to confirm the model GE RANGE that I have. Kinda lost it on her... On Thursday serviceman from local dealer comes. Turns on the dishwasher - it leaks exactly where I had said it would. Need to order a part and GE will not expedite. End of week 2. Next week - crickets. Nothing, Nada, mushroom mode (in the dark and being fed BS). Called my appliance dealer today and told him to come pick up the dishwasher - says he cannot do that. I explained, “I will forfeit the money I paid - I dont want a dishwasher that leaks in the first two months of use.” He tell me GE released the part yesterday...whatever THAT means and he HOPES repairman will come next Tuesday to repair. So, I have had a new GE dishwasher for 3 months and it has only worked for 2. Be aware! I assume partial responsibility for this goat rope - I faithfully refer to Consumer Reports when purchasing appliances and electronics. I suggest you do the same... you will find GE listed AFTER BOSCH, KITCHENAID, KENMORE and others. Also, realize the GE brand is now a CHINESE company. Caveat Emptor!

Paint is peeling on the top part of the oven. It could fall into food. This seems to be a common problem. Called GE. They said it could not be repaired and to stop using it. Buy a new one. What kind of product do they put out that cannot be repaired? Not very good in my estimation. Customer Service did not offer much assistance to replace it. Be warned. Don’t buy GE products.

Our dishwasher has gotten very warm mid-cycle and now trips the breaker in the house each time we run the cycle. The problem became evident in April 2012. We have called in a GE repair person to fix it and they said it was a heating issue and not repairable. We have not used it since, but have not replaced it with a new one yet. In August, we read about the recall of a similar model number manufactured within same time frame. Our machine model is PDW7300J03WW, the recalled model is PDW7. Our machines serial # is **. Strangely, the serial number is not listed in the recall, even though symptoms are exactly the same!We have called GE Consumer Affairs at 1-800-386-1215 four times, the most recent today, 9/14/2012. Each time we call, we are left on hold for 59 minutes only to be disconnected automatically! I am sending a registered letter to GE CA with a copy of this link and intend to contact my local news if I do not receive sufficient response within the week. Does GE need to see an actual fire report from my fire department or worse in order to get their attention to replace the unit? It is disgraceful and extremely dangerous.

In 2008 I redid the entire kitchen and purchased all GE Profile stainless steel appliances thinking I was purchasing quality items. Well, it didnt take long before the dishwasher broke but it was fixed for free by GE under a recall. However, now the refrigerator has begun to leak under the right corner of the ice/water dispenser located on exterior of freezer door and the microwave touchpad has also failed as I need to press below the actual keys for it to work half the time. When I spoke with GE customer service they basically told me there was nothing they could do with the refrigerator, I would have to call a repairman and have it looked at or pay their $100 diagnosis fee.The microwave they told me had issues with that particular touchpad and had it broken within first 5 years they would have repaired it for free under their recall program. But since its 7 1/2 years old I would have to buy the touchpad which normally only lasts for 6 months to 1 year or buy a new GE microwave and they would offer a rebate. Im so unhappy with their customer service and poor reliability of their products that Ive passed on each offer as I dont want to contribute another penny to a company that in my opinion is unethical and has horrible reliability. 3 out of 4 of my fancy GE Profile stainless appliances have broken! Thats a 75% failure rate! No thanks, Ill buy elsewhere. No wonder they cant sell their appliance business and why the stock hasnt moved in years... Wake Up GE, do whats right for your customers!

My GE Washing machine did everything it was supposed to do, especially in cleaning clothes and very few if any machine problems and they last years and years, mine was 15 years old. It kept surprising me because it ran so smoothly, truly cleaned my clothes and ran forever. The Dryer couldn't keep up with my old washer, had to buy a newer more expensive machine that couldn't dry at 8 years old. I loved my reliable GE washer.

A few years ago, I purchased a brand new GE microwave oven. A week ago the microwave oven stopped working. I contacted an Appliance Repair company for repair. When the tech came & disassembled the microwave oven, he discovered pliers inside the oven. We took pictures of it (BTW, it wasnt the cause of the problem). I contacted GE to alert them of this & they told me that the robots that assembled the microwave oven probably dropped it in there. Then they said they will send a tech to my residence to investigate. I told them that the pliers was removed & the microwave oven is fixed & assembled. Nonetheless they sent a tech anyway. I told the tech what his Customer Service said & he said he wasnt surprised about the tool being inside an appliance from GE & GEs response. In summary, I would not recommend purchasing any GE products. They proved their products are a safety hazard & they dont care about the consumer nor their safety. All they care about is taking your $$$.

I also have a GE Profile dishwasher with malfunctioning wheels. I read this site, and was comforted and enraged that I was not alone with my melting wheels. I sent GE customer service a note, explaining my problem. I also included a link to this site in my note. I explained that I was a loyal GE customer and that they should stand behind their products although my unit was no longer covered under warranty and did not qualify for the recall. GE responded to my e-mail with in 12 hours. They sent me a complete set of new wheels for my bottom rack free of charge, and sent out a technician to install them, again free of charge. They also e-mailed me to make sure I was happy and no longer had concerns. I am thrilled with my experience. Let me say that again I e-mailed GE and within 8 days (a holiday included), I had new wheels and a technician to install them at no charge.

Dishwasher looks and works beautifully. It is slate black and I have never had to redo any dish or glass. It is located. About 12’ from our bedroom door and we turn in on before go to bed. It is so quiet that we never have our sleep disturbed.

We purchased a new home with a GE Profile dishwasher installed. Since the day we had it, we have never been satisfied with the cleanliness of the dishes. They frequently come out covered in food and must be rewashed. We now routinely prewash everything in the sink and we always use the cookware setting to wash everything. Despite this, we still have to re-run loads because they are not clean.I am convinced that there is a design error with our dishwasher, because the top dish shelf obstructs the door of the soap compartment and prevents it from fully opening. After a load has run, you can still see leftover soap dried and crusted in the soap container. If the dishwasher cannot even wash the soap out of the soap compartment, no wonder our dishes are not clean.

When I entered my home I notice the microwave door was open and light was on. I closed it and took packages to my room. When I entered the kitchen I seen flames coming from inside unit. I put out flames with a fire. The panel was off and microwave was empty. My son said he left the door open because when he closed it hummed. I am very blessed that my home or loss of life did not happen. I contacted GE to see if there was a recall and was offered a 20.00 discount. I really feel that this is a hazard waiting to happen.

After having my Cafe Stovetop for about a year and a half, there was a electrical component malfunction. During this, smoke came out of the stovetop and it smelled of electrical burning. I sent a complaint to GE since several components were damaged. Knowing that the warranty was only for 1 year, there would be nothing they could do except sell me the parts.

GE Dishwashers are very dependable and do a great job. I have not experienced any issues with mine. The pricing is very competitive and easy on the wallet. You may be able to find a cheaper dishwasher but just remember, you get what you pay for.

GE is the only manufacturer who still makes an under cabinet size microwave and therefore I use this product. I renovated my kitchen 14 years ago and on my second microwave. It is small, but does do its job, but when I work with a larger microwave I realize how different it is due to its size and less powerful.

Does not hold as many dishes, pots and pan as my previous dishwasher. In the bottom rack I cannot place plates and bowls side by side. Rack is too small and the gray interior is too dark. And the top rack does not hold the glasses in place, already had one break.

Bought the whole GE profile kitchen series 2 years ago. Last week the microwave went dark, blew a component, and is dead. With only two people using it off and on for reheating, hardly got our money worth. Called GE for assistance and went back to the store where it was purchased. No one offered any financial assistance with the loss. The microwave itself was $500. My husband and I are very disappointed in the product and service.

I have a GE Profile model JT965SK4SS micro/oven combo. It came new with my new home. A couple years into it, the paint (lining) interior of the microwave start to bubble and peel and eventually started rusting. Had SEARS come out (warranty had expired) who contacted GE and they concluded it was only cosmetic that it doesnt affect the functioning of the microwave. Well, its gotten a LOT WORSE now, bubbled peeling paint all over inside, rust, exposed metal, and the paint is falling onto food. I can NOT even wipe out the interior to clean it, it makes more stuff come off/fall down. I called GE last week, was told by 2 employees that it is NOT safe to use anymore, discontinue use. I had SEARS come again (per GE). The tech said he had NEVER seen anything like it before. He called GE to tell them its not safe, exposed metal, and its dangerous. They again said, well maam, youve gotten 8 years use of it. We wont replace it, but will offer you a discount for a new one ($2,500 out of pocket for me). The person who had offered me the discount (yes, I sent pictures, showed how bad it is) also gave me a tip regarding the unit I have now with the exposed metal and the chance of arcing (spelled? like Ark) if the unit catches on fire, make sure not to open the doors, the fire should contain itself. 2 employees told me its not safe, a 3rd gave me helpful info for if/when it catches on fire... and yet, they still wont replace the unit... and do not stand behind their own products. I plan to go to our local news station, see if they can get anywhere with this, since they wont do anything. Patiently waiting and unable to afford a new unit.

Beware of GEs scam! My new house came with a GE microwave oven model JVM1630. It no longer heats food so I called GE repair. Heres basically what they told me: It is likely the magnetron tube and it is still under warranty, so no charge to replace it but I would have to pay $99.95 for the repairman to come to my home to diagnose the problem. If I decided I didnt want to repair the microwave, I was offered a $100 coupon toward a new one but it had to be a GE and it had to be bought on their website only. If I decided to go ahead with the repairs, the $99.95 would be deducted from the bill and I would only have to pay for additional parts and labor. I repeatedly asked for a ball-park labor charge so I could make an informed decision as to whether it was cost effective to have the repairman come out or just get a brand new one elsewhere. The person on the repair line hung up on me! I called back and I was told the same thing; that no one could tell me what the labor cost estimate might be. I asked to talk to a supervisor and same story. I didnt schedule a repair because I was taking a long trip and wouldnt be using the microwave anyway. When I returned from my trip, I called GE repair and again they wouldnt give me a ball park figure. Frustrated, I decided to have the repairman just come out and repair the darn thing and an appointment was scheduled for the next Monday. I had to rearrange a Monday day trip to Wednesday and set the repair appointment. On Monday, it was starting to get late in the afternoon, so I called to find out if the guy was on his way. A recording said my call was noted and I would be receiving a follow-up call. About 10 minutes later, Kim in dispatch called to tell me she had to reschedule the repairman to Wednesday. I explained I already had an appointment on Wednesday. which was already changed because it conflicted with the repairman coming to my home. She told me the repairman couldnt come because his truck wasnt safe to drive so that whole day was shot. The appointment was rescheduled for Wednesday and I had to again reschedule my other trip. When the guy finally showed up on Wednesday, he told me to put a glass of water in the microwave and start it. Ten seconds later, he declared it to be the magnetron tube. He was at my house about 10 minutes, just long enough to take my $99.95 credit card payment and to give me an estimate of $246.90 to repair the microwave which included the free magnetron tube, a $20 part plus tax and labor. The estimate had instructions on how to get the $100 coupon if I decided to buy a new GE microwave, which he said is what most people do. He didnt seem like he came prepared to repair the microwave at all. I was so frustrated and already out the $99.95, so I told him to go ahead and repair it. He said I should call repair to schedule him to come back to repair it! I told him to just repair it now and he said he didnt think he had a magnetron tube in his truck. I asked him if he would go to the truck and check! He did, and nope, no tube and he left.I think this is a great scam GE and maybe others have going. Its entrapment. They get you to accept a repairman to come to your home and charge you nearly $100 for it, but give you a coupon for $100 for a new one but it has to be a GE and can only be bought from their website where they can go as high as $500 or $600. By the way, I got on the website to find a replacement. My model had been discontinued and the only one in my price range was also a discontinued model. They charge $75 to come out to install it and another $30 to take away your old one. I called local appliance stores to see if I could unload my old microwave for parts and they all said the same thing: stay away from GE products.

I moved into our house about 27 years ago, and have had to replace every single appliance except the microwave. The oven, fridge, washer, dryer, dishwasher—all replaced at least one time over. But this 90s GE microwave keeps humming along. I really should replace it just because it is this awful off-white color and everything else in our kitchen is part of a beautiful stainless steel/black/white scheme, but it is actually built right into a cabinet and I fear I will not be able to get another microwave in there. The only gripe I have about its performance is the fan comes on and roars full-blast anytime the stove or oven is on. It is so loud its difficult to talk over.

I was very impressed by the look of the GE over-the-range microwave oven but my impressed state faded not too long after I began using the oven. My typical usage ranges from heating something for 20 seconds to soups for three to four minutes. Within the first month of purchase, the paint on the floor of the oven was peeling off, exposing the metal color. I was only wiping/drying out the oven with a soft cloth, never using an abrasive product or cloth, so the peeling paint was only due to moisture. I have now owned the oven for just over 14 months and not only is the floor nearly completely devoid of the white painted surface but I just had a quick fire when thawing frozen onion chips for 10 seconds. My previous, much less expensive microwave lasted nearly 7 years, so its a shame that a supposedly better model cannot match the longevity of the GE model. Looks aside, I would not recommend a GE microwave oven to anyone looking for a new or replacement microwave.

GE microwave model JES1344ES. This is a stainless steel with black accent 1.34 cubic foot microwave oven. It looks great. The micro is heavy for its size. The stainless steel is brushed and low luster finish. The door handle is chrome as is some of the other accent pieces. The push button panel is easy to read and has a large knob for making manual time adjustments. The light inside is very bright. There is a rotating platter in the oven compartment that is not knocked off of its guide rollers very easy. The push button panel is a glossy black material that is easy to attract fingerprints. The preset times that are programmed in the microwave is the only part of the product that could be an issue. For example the popcorn button when used has burnt all of the different brands of microwave popcorn that we have tried. It is set about 30 seconds too long. There is no way to adjust the preset time that I can figure out. We set the time with the large knob manually and the popcorn comes out just fine. The preset times for the Auto Defrost are also a bit off. They are not long enough. We also have a Subzero freezer set at minus 20 degrees Fahrenheit so that may be too cold for the defrost presets. Overall the microwave is great except for the preset times that Ive mentioned. We use it daily and have done so for five years. It still looks excellent inside and out.

I was missing my wiring/ schematic diagram with my dishwasher and after spending hours on GE website to no avail I called the service center and was told they would send me an email that I would have to respond to and then they would email me a diagram in 8-10 business days. Email in 8-10 business days... WHAT!!!! I replaced the UI board after 2 1/2 years and the control board Fault code LED was blinking 7 times for a temperature sensor circuit has become inoperable. This is their fix; Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher. If the problem persists, contact service. No instructions on how to reset the dishwasher anywhere. American business at its best. Never GE again!

The WORST Customer Relations Department & GE Dishwasher EVER 1. Ordered dishwasher & Scheduled Delivery. 2. After my 4 hour window of waiting, I was called and informed the installation needed to be cancelled due to the installer calling in sick. 3. During installation, they dropped my dishwasher & dented the door. I rejected the dishwasher as my other one was already hauled out. 4. Due to my hectic work schedule, my dishwasher was installed about 2 weeks later. 5. Dishwasher was not cleaning. 6. Technician came out another week later and I was told it was MISSING parts from the manufacturing plant and should have never passed QC. In addition, It was missing the bottom spinner and the top spinner was snapped off. The technician glued it back on.7. Called Customer Relations to get the runaround saying, its not their fault it came from the manufacture missing parts.In closing, I own a large apartment complex and have many BUSINESS friends. I will NEVER buy a GE product EVER again and to think of all the people I know, Im going to share my horrid experience with everyone I know. This will make great conversation when golfing too.

We bought a microwave oven (CVM1790SS2SS, ZA301193K) for our new house some 4.5 yers ago. The flimsy, but very shiny, metal cover on the door handle split and the resulting sharp, but hidden, edge cut my finger. We covered it up with scotch tape, and ordered a replacement for the handle. We paid GE $102 (other folk sell it for $76, as we later discovered). There were no useable installation instructions. Our extremely competent handyman could not figure out how to do it and called GE for help at 800 636-2005. He was rudely dismissed and was told to look for instructions on Youtube! He spent 2 hours to install the replacement part. The screws that came with it, were not quite right. Ill never buy another GE appliance in my life. The Item was ordered by Ellen ** (It was shipped on 1/17/2017).

My GE dishwasher is 30 years old and has never had a service call. It has a built-in food grinder and my dishes almost always come out spotless. Standard size, upper rack, removable utensil basket. Almond with a dark faux instrument panel with rotary dial. It was a builders model. Works like a charm but very noisy. Even though Im a small family Ive tried to use it consistently to keep the seals lubricated. It has stayed really clean inside with just using the dishwasher detergent. Unit does have some kind of preheat Electrical for the dish water temperature. The new ones dont work so well so Im afraid to replace it.

It could clean better without pre-cleaning. Its necessary to pre-clean heavily dirty items. Works ok if dishes are just moderately dirty. Could also be quite a bit quieter. However it is about 15 years old and still running but sometimes motor freezes up if not run often.

Seems to be a lot of wasted space in this GE dishwasher. If it had a 3rd rack then I would rate it higher. The back has additional sprayers, but the sides do NOT. I would think that having sprayers all the way around would help with sanitation.

We have a GE profile dishwasher for about 14 months. I just found out last week that its out of warranty and that the 2 circuit boards inside are bad so the tech came out and didnt have a replacement board on his truck saying they never have problems with this dishwasher so hell order this part and be shipped to my house. He would install it on the following Thursday so Im sitting here waiting for service. I finally called to find out that GE decided that it is going to be repaired on Friday. I did not know this of course so I asked for a supervisor. I was put on hold with no answers, finally hung up in disgust.

Bought a new GE microwave cafe series in May 2014. Within one month the handle which was not stainless steel started to peel and cut my wifes hand. GE sent a replacement new door for the unit that did not close. Then he had to transplant the handle from the new door to the old door. A month later the unit failed. A new replacement unit took 2 months to replace. It has worked 3-4 weeks and has also now totally failed. Our experience with GE CAFE microwave and GE service process is poor to miserable. I would not recommend this product or their service to anyone.

18 Dishwasher Model GSM1860VSS - Cleans terrifically but I have a problem with either a leak or steam which is running the front of my dishwasher and marking it. It seems to be leaking from the black panel across the top. If I check inside behind the black panel I can see marks where water has been running. Please let me know how to fix this. The dishwasher was bought in 2015 and have the receipt from Home Depot. Thanks.

Needing some type of warning to indicate a clog or break down. Cycle: Pots & pans; heavy wash; normal wash; light wash; hot start; high temp. wash; heated dry; energy saver; cycle on: plate warmer; start delay (hrs) off, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1; Hot start plate; Pots & pans start; heavy/normal; high wash; heated dry off-rinse only. The color fits my kitchen arrangement. Needs to have a better warranty coverage. Needs a longer warranty on the basic coverage. Do away with extended coverage. Offer all parts and full labor for a longer time.

This GE Model JNM1541 is a 1500 watt, under counter microwave with quite a few features. It has plenty of cooking power and has not failed in its nearly 5 years of use. I have never used the included metal shelf.

We first noticed a problem with our two-year old dishwasher when the lower spray arm broke. Soon after, the door seals started to leak, and we noticed the seal at the bottom of the door had completely degraded becoming brittle and breaking off. Our warranty had expired, but I contacted Mabe. They agreed to replace the parts free of charge, which amounted to approximately $300. I expressed concern that the dishwasher may have been overheating, causing the above problems, but this wasnt given credence as the technician didnt speculate in his report on the cause of the damage.Within the next month, we had a massive water leak. Upon inspection, the dishwasher showed signs of extreme heat. The sound insulation had bubbled and melted off much of the exterior of the tub. The electrical supply cord had a scorch mark. Once again, Mabe was notified. After much negotiation, they agreed to refund the price of the dishwasher. Initially, they had offered a certificate valued at 50% of the cost of our dishwasher towards the purchase of another GE dishwasher. This offer was declined as we wont have another GE dishwasher in our home unless were convinced theres no fire hazard.There are significant repairs required to our home due to water damage but we consider ourselves lucky to have avoided a fire. GE has had problems with their dishwashers in the past which resulted in a massive recall. Its time for them to acknowledge that there is a problem with the Cafe line and take measures to rectify the problem before someone is injured.

Have a GE dishwasher put into operation June 2016 (new home). In Oct 2016 we noticed a leak and a serviceman came out and identified a loose soap dispenser - tightened it. Next time we used it, leaked as before. Same serviceman came again, this time replaced both the main seal & spinning water distribution wand assembly. Again, the unit leaked and on Dec 14th same serviceman replaced the soap dispenser. Before he got too far down the road, we called as the unit again leaked. He blamed it on excessive soap suds - which he removed manually. Following his departure, we again experienced a leak. Same serviceman returned on Dec 15th. After review, he advised us the DW would be replaced and we should get a call within 48 hrs to arrange. On Dec 17th (still no followup from GE) the DW leaked again - we video this time. On Dec 19th called customer relations and after much discussion it was apparent GE has NO CLUE what the heck they are doing. ONE MORE repair trip was scheduled - this time they would replace the inside and outside panel! We are fortunate to be retired otherwise this repair process would have cost us about $2000 so far! How idiotic is GE?? How much have they spent to avoid replacing this unit? Believe me this is the LAST GE appliance we buy from them. Dont know how they stay in business. We are awaiting the panel repair guy as of this writing. Will update once this service has been completed.

A durable microwave. Our microwave has stood up to 13 years of pretty heavy use and all functions continue to perform as when new. Has turntable but would be nice if it had two shelves instead of one. Guess that has to do with the spacemaker size of this microwave.

I purchased a GE Smart water heater and installed in October 2004. I have not had any issue or problem. 50 gallon natural gas unit for 5 people. 40,000 BTU I am looking to replace before there is a problem and will certainly look at GE again, but these more recent reviews are a concern. The trouble is, these websites attract those who are dissatisfied and may give a biased view of a product.

The GE microwave oven that was installed by the owners of my 130-something unit apartment complex caught fire in June 2014. The manufacture date is listed as December 2012. I moved into the unit in June 2013 and the microwave was brand new still and had never been used by anyone else. I myself rarely use the microwave and only use it for heating up cold food that I previously cooked on the stove top. After heating up rice using the 2 minute express option and removing the food from the microwave, I had gone to the restroom for 30 seconds only to return and find the microwave on fire. The fire ignited from the ceiling of the microwave. I had initially intended on going to the bathroom to take a shower but needed to open a new bar of soap, so I had only returned to the kitchen to throw the soap packaging in the trash. Had I not done the latter, my entire apartment could have caught fire and it would have been difficult if not impossible for me to escape from my third floor apartment. Reading all of these complaints it is really hard to believe that a government agency has not stepped in and forced GE to STOP MAKING MICROWAVES! From the complaints on this board it is clear to see that every year GE continues to make appliances that put consumers safety and lives at risk. You would think that after so many recalls that they would have perfected their product by now, but that is not the case. It almost seems as though they are just slapping new model and serial numbers on the same BAD product. The management in my building contacted GE and my microwave was replaced with another GE microwave manufactured in 2014. I did not want another GE microwave, but I only rent so I didnt have a choice. I used the microwave once so far and the fan automatically came on after 2 minutes of use. It does state inside the microwave that the fan may come on automatically, but I just dont trust this brand anymore. I have a countertop microwave that works perfectly fine that Ive owned for over 15 years that I will be using. I will unplug the GE microwave and just keep it for aesthetic purposes, since thats all its good for.

Our first microwave lasted 15 years now this one 1.5 year. No help just buy a new one. Or pay 100 for their service call. 100’s of consumers with same exact problem and they just get away with it. Ridiculous.

We moved into our new manufactured home in May of 2013. That is the month our above range built-in GE microwave was installed. In October of 2013, one of my sons heated a frozen chicken cordon bleu serving for 3 minutes, 45 seconds, according to packaging directions. He said that some of the inside of his food was cool, so my other son put in his serving for four minutes, zero seconds. All of the packaging was removed and each serving was placed on a separate Corelle plate and covered with Glad microwave-safe plastic wrap. While heating the second serving, the microwave started on fire. Fortunately, my son extinguished the fire before it spread. The food did not combust. The fire seems to have started from the ceiling behind the fan. The entire inside of our microwave is clean except for the soot that billowed out from the center of the ceiling. When the service tech came, he scrubbed the soot off of the ceiling with some paper napkins (which he left inside of the unit) and said that the microwave was a total loss. He also said the fire was caused by misuse, because plastic wrap is not meant to be used in the microwave, therefore even though the fire happened within a year of purchase and installation, our warranty was void. I asked GE to get a second opinion and they agreed to send a third party servicer (A&E) who stood me up three times! I finally got to schedule a GE tech to come at the end of December and they sent the same guy who said the fire was our fault! He told me that he never said plastic wrap is not meant for the microwave, but that we are being dishonest because fires only start when the food is left in the microwave for too long. He accidentally let it slip that he is seeing the same problem with GE microwaves in a lot of new construction for student housing in Tallahassee. (We live 20 minutes south of there.) He attempted to recover GEs reputation afterward by saying that of course it was the students faults, too, for misusing the microwave units. Anyway, GE has graciously offered to sell us a new microwave at slight discount. Haha, no thank you!

This is a review from another customer “Not only does this dishwasher do a lousy job of cleaning dishes, I have just found out it allows dirt to collect under the door flange==lots of dirt! There isnt enough hot water to clean this out. Very gross--do not buy.” I agree with this 100%. I have to use Clorox wipes to wipe out this disgusting sludge that builds up under the door flange every couple days. I have to buy a new dishwasher because my dishes smell, are still dirty and very unsanitary. Do not buy!!!! My dishwasher is only 3 years old.

Microwave lasted 6 months, very light duty, burnt metal smell. Purchased from Walmart, they told us to contact GE. All GE could offer is a Good Will certificate which means, we have to go buy another GE microwave up to $155 in value. We pay taxes, shipping etc. Not really a customer-centric return policy for a lousy designed product made from cheap components in Asia. These microwaves are a piece of junk. This isnt the only complaint about this model of microwave. Others are experiencing the same problem all within the past 6 months. From March 2018 thru August. Stay away from these microwaves.

Almost immediately after purchasing the GE microwave we started having problems with the circuit board. It is now totally on the blink after only 4 years. This was a high price appliance. Sometimes when setting the timer on 30 seconds, the microwave would still be running and after looking at the timer it would still have 4 or more minutes left to cook. This is a FIRE HAZARD! We have lost food from timer malfunctions. This is a product I would be afraid to purchase. I am wondering why cant there be recalls on these cheaply built defective microwaves since you read of the same malfunctions over and over. GOODBYE GE!

We purchased a GE Profile Microwave with our GE Profile range in 2010. In 2016 we noticed an area on the bottom of the back wall that was peeling. It is in an area where nothing is rubbing or touching it. After taking photos and contacting GE customer service I was offered a discount on a replacement microwave. I expressed my concern that a new microwave might do the same thing--peel. I was told that the newer microwaves have a moisture resistant paint. The area that has peeled is much larger now than is shown in the attached photo taken in 2016. I expected my oven to last longer than 6 years; its a GE Profile and we take excellent care of our appliances.

We purchased our new GE Over-the-Range Microwave (model HVM1750DPWW, 1.7 cu. ft.) for $269.00 in February of 2012 and in August of 2013 it started to malfunction. Specifically the microwave would start on its own whenever we would OPEN the door. Now the microwave does not work at all (with the door closed or open). Based on the feedback that I have read in some of the posts on this site, I will replace the microwave since the maker can no longer be trusted to manufacture units that are robust and safe. But what manufacturer can be trusted at this point? It is my understanding that all microwaves (from all major companies) are currently made overseas with poor materials and highly suspect safety and quality standards. (Note - previous GE Microwave [same type - over the range] lasted for 14 years.) Thanks to Consumer Affairs for allowing us to post unfavorable reviews.

I have used 4 dishwashers of various brands in my house over the past 30 years. The current one is a new GE dishwasher (Model No: GDT695SSJ0SS), which is by far the worst. The dishwasher never dry, no matter which cycle I choose. When it is done (green light on) water still flowing down everywhere inside - on the door, on dishes, at the bottom. When I called GE customer service it said I have to use rinse agent in order to get it dry. Of course that means we have to constantly buy that additional product (made by a GE subsidiary?).For those who dont remember this, our old dishwashers did not required the use of additional product and still dried dishes perfectly. GE is apparently producing products of lower quality, yet the repairman sent by GE claimed that this model is their best ever. Really? Is this company so arrogant that it pays no attention to the convenience of its customers? Since the repairman found no defect with the machine (even though it does not dry), GE refused to accept either a replacement or a return. From design to functions to price this is indeed a lousy machine. Ill never purchase another GE product again.

The dishwasher is new and looks great. However the dishes are not getting clean. After washing with a 200+ minute wash cycle utensils are still dirty and food particles are left on plates and bowls. This is occurring even with a good rinse prior to placing them into the dishwasher. I clean out the food particles filter after every two loads, makes no difference. Also the water bottle jets are a nice idea but water bottles are too tall to fit even with the third rack removed. I am very displeased with my purchase. This was not an inexpensive model.