Appliance Types


Appliance Brands


Article Categories


More Articles


Maytag Appliances
Maytag Appliances

Maytag Appliance Repair

The Maytag Washing Machine Company was founded in 1893 by businessman Frederick Maytag. In 1925, the Maytag Washing Machine Company became Maytag.


Dishwasher Repair

For the home, kitchen and beyond, Maytag manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Maytag appliance repair from experienced professionals, your local Appliance Helper can help.

Maytag Dishwasher not cleaning 
Water Inlet Valve. The water inlet valve opens to allow water to enter the dishwasher. If the valve is clogged or defective, the dishwasher won’t get enough water to clean dishes properly. If the water inlet valve is clogged, replace it. Do not attempt to clean the water inlet valve—cleaning the valve could make it more likely to fail. 

Maytag Dishwasher not draining 
Drain Impeller. The drain impeller pushes water through the drain hose and into the garbage disposer or drain line. If the impeller is broken, replace it. 

Maytag Dishwasher buttons not working 
Touchpad. First, confirm that the dishwasher display is working. If the display is still working, try pressing some of the touchpad buttons. If some of the buttons respond correctly but others don’t, it is likely that the touchpad is at fault. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.) 

Maytag Dishwasher lights flashing or blinking 
Heating Element. The heating element heats up the water to operating temperature. If the water doesn’t reach the proper temperature after a set amount of time, a light on the control panel might start flashing. To determine if the heating element has burned out, use a multimeter to test it for continuity. If the heating element does not have continuity, replace it. 

Maytag Dishwasher leaking 
Water Inlet Valve. The water inlet valve opens to allow water to enter the dishwasher. If the water inlet valve is stuck open, the dishwasher will continue to fill with water until the dishwasher leaks or overflows. If the water inlet valve is at fault, replace it. Water inlet valves are not repairable—if the valve is defective, you must replace it. 

Maytag Dishwasher leaking from motor area 
Impeller and Seal Kit. First, try to determine the source of the leak. If the water is leaking from the motor shaft area, the motor shaft seal is likely defective. If the seal is defective, replace it. (Some manufacturers sell the seal independently of the impeller. Other manufacturers require that you purchase the impeller and seal together. Still other manufacturers require that you purchase the entire pump and motor assembly instead of the impeller and seal. It is usually more cost effective to replace the impeller and seal kit rather than the pump and motor assembly.) 

Maytag Dishwasher won't start 
Door Switch. The door switch prevents the dishwasher from running while the door is open. If the door switch is defective, the switch will prevent the dishwasher from running even when the door is closed. To determine if the door switch is at fault, use a multimeter to test the switch for continuity. If the switch does not have continuity, replace it. 

Maytag Dishwasher won't latch 
Door Hinge. If the door hinges are damaged, the door won’t be able to latch properly. Inspect the door hinges for damage. If a hinge is bent or broken, replace it. 

Maytag Dishwasher dispenser not dispensing soap 
Bi-Metal. The bi-metal actuator is a metal loop which acts as a latch for the dispenser door. As electricity is applied to the bi-metal, it deforms and bends away from the latch, releasing it. If the bi-metal is burned out, it won’t release the dispenser door. To determine if the bi-metal has burned out, use a multimeter to test it for continuity. If the bi-metal does not have continuity, replace it. In addition, make sure that the dishwasher is getting enough water. If the water level is too low, the wash motor may not draw enough current through the bimetal, causing the bimetal not to bend enough to work properly. 


Dryer Repair

For the home, kitchen and beyond, Maytag manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Maytag appliance repair from experienced professionals, your local Appliance Helper can help.

My Maytag Dryer Isn't Starting 
Thermal Fuse. The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good. If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown. A multimeter can be used to test it for continuity. Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check the dryer venting when replacing a blown thermal fuse.  

Maytag Dryer stopped spinning 
Drive Belt. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. Over time, the belt can break from normal use. If the belt is broken, the dryer won’t turn. To quickly determine if the belt is broken, reach into the dryer and turn the drum by hand. If the drum spins very easily, the belt is likely broken. Next, inspect the belt to confirm that it is broken. If the belt is broken, replace it. 

My Maytag Dryer's Not Spinning 
Drive Belt. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. Over time, the belt can break from normal use. If the belt is broken, the dryer won’t turn. To quickly determine if the belt is broken, reach into the dryer and turn the drum by hand. If the drum spins very easily, the belt is likely broken. Next, inspect the belt to confirm that it is broken. If the belt is broken, replace it. 

Maytag Dryer takes too long 
Air Flow Problem. If the vent is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time. To ensure proper dryer performance, you should clean your dryer’s venting system at least once per year. 

Maytag Dryer overheating 
Heating Element. The heating element warms the air before the air enters the dryer drum. If the element is partially shorted out, it may produce heat continuously, even if the dryer has reached the proper temperature. When this happens, the dryer gets too hot. To determine if the heating element is at fault, use a multimeter to test each terminal for continuity to the case. If the heating element has continuity to the case, it is shorted out. If the heating element is shorted out, replace it. 

Maytag Dryer won't stop 
Air Flow Problem. If the vent is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time. To ensure proper dryer performance, you should clean your dryer’s venting system at least once per year. 

Why is My Maytag Dryer not Heating? 
Thermal Fuse. The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good. If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown. A multimeter can be used to test it for continuity. Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check the dryer venting when replacing a blown thermal fuse.  

Maytag Dryer tripping breaker 
The Circuit Breaker is Weak. Over time, circuit breakers can weaken. If the circuit breaker is weak, it may trip too often, even if the amperage draw is below the limit. If you have already checked all of the potentially defective dryer components, consider having an electrician replace the circuit breaker. 

Maytag Dryer makes noise 
Drive Belt. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor. Over time, the drive belt can become frayed or otherwise damaged. If the drive belt is frayed or damaged, the dryer will be noisy as it turns. Inspect the drive belt for signs of wear. If the drive belt is worn, replace it. 


Microwave Repair

For the home, kitchen and beyond, Maytag manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Maytag appliance repair from experienced professionals, your local Appliance Helper can help.

Maytag Microwave not heating 
Diode. The diode converts the A/C power output of the transformer to D/C, doubling the voltage to nearly 5,000 volts. This high voltage powers the magnetron to heat the food. If the diode burns out, the magnetron won’t receive enough voltage to operate, preventing the microwave from heating. When the diode fails, it is often visibly burned out. Inspect the diode and if the diode is burned out, replace it. If inspecting the diode proves inconclusive, test it with a multimeter that uses a 9-volt battery or put a 9-volt battery in series with the diode. When the leads are reversed, the diode should only have continuity in one direction. (Warning: The microwave oven can store a lethal amount of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the high running voltage and the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the diode.) 

Maytag Microwave not working 
Line Fuse. If too much current passes through the microwave circuitry, the line fuse will blow. If the line fuse blows, the microwave won’t start. To determine if the line fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it. In addition, you should investigate and resolve the problem that caused the fuse to blow. If you don’t resolve the underlying issue, the new fuse will blow too. (Caution: The microwave oven can store thousands of volts of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the line fuse.) 

Maytag Microwave light bulb not working 
Light Bulb. The light bulb itself might be burned out. Replace the light bulb before replacing any of the parts associated with the light bulb 

Maytag Microwave shuts off after a few seconds 
Door Switch. A door switch might be failing intermittently. Check each of the door switches for signs of overheating, arcing, or burning. If you don’t see any obvious signs of failure, use a multimeter to test each switch for continuity. If any of the switches is visibly damaged or only has intermittent continuity, replace it. 

Maytag Microwave turntable not turning 
Turntable Motor. Use a multimeter to test the motor for continuity. If the turntable motor does not have continuity, replace it. 

Maytag Microwave buttons not working 
Touchpad. To determine if the touchpad is defective, try pressing each of the buttons on the control panel. If some of the buttons respond correctly while others don’t, replace the touchpad. 

Maytag Microwave display not working 
Main Control Board. If the display goes out partially, the display board is more commonly at fault. If the display isn’t working at all, either the main control board or the display board could be at fault. 

Maytag Microwave turns on by itself 
Main Control Board. First, make sure that the touchpad is working properly. If the touchpad is working properly, the main control board is likely at fault. If the control board is defective, replace it. 

Maytag Microwave is sparking or arcing 
Waveguide Cover. The waveguide cover might be damaged and shorting out. Try removing the waveguide cover and see if the problem resolves. If the waveguide cover is burnt or will not stay in place, replace it. 


Range Repair

For the home, kitchen and beyond, Maytag manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Maytag appliance repair from experienced professionals, your local Appliance Helper can help.

My Maytag Oven's Not Heating 
Igniter. The igniter is the most commonly defective part for an oven not heating. The igniter has two main functions. First, the igniter draws electrical current through the oven safety valve to open it. Second, the igniter gets hot enough to glow and ignite the gas in the oven burner. If the igniter gets weak, it will fail to open the safety valve correctly. If the valve does not open, the oven will not heat. To determine if the igniter is defective, observe the igniter when the oven is on. If the ignit. 

Maytag Oven doesn't bake evenly 
Bake Element. If the bake element is burned out, the oven will only be heated by the broil element. This will cause the oven to heat unevenly. When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the element has burned out, it will be visibly damaged. Inspect the bake element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it. 

Maytag Oven broiler not working 
Broil Element. The broiler element may have burned out. When the broil element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the element has burned out, it will be visibly damaged. Inspect the broil element for holes or blisters. To determine if the broil element has burned out, use a multimeter to test the element for continuity. If the broil element does not have continuity, replace it. 

Maytag Stove heating element not working 
Surface Element Board. The surface element board has relays that regulate the power supply to the burners. If one or more of the relays fails, the surface element won’t work. If two or more burners fail at the same time, this indicates that the surface element board is likely at fault. If only one surface element won’t work, use a multimeter to test the element for continuity. If the surface element has continuity, the surface element board might be defective. 

Maytag Stove burner won't light 
Spark Module. The spark modules provides power to each surface burner spark electrode. If the burner is produces a weak spark, or if the burner sparks intermittently, the spark module might be defective. Before replacing the spark module, first check the spark electrode and the spark wire. If the spark electrode and spark wire are not at fault, the spark module is likely defective. If the spark module is defective, replace it. 

Maytag Oven temperature not accurate 
Bake Element. When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the heating element has burned out, it will be visibly damaged. Inspect the heating element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it. 

Maytag Oven light is out 
Light Assembly. If the oven light is out, the entire light assembly may need to be replaced. Often the light assembly components are not sold separately. 

Maytag Oven won't turn on 
Bake Element. When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the heating element has burned out, it will be visibly damaged. Inspect the heating element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it. 

Maytag Oven not self-cleaning 
Door Lock Motor and Switch Assembly. During the oven's self-cleaning cycle, the door lock switch activates the door lock motor to prevent the oven door from being opened. If the door lock motor and switch assembly is defective, the oven door will not unlock once the self-cleaning cycle is complete. On most ovens, you can open the oven door by removing certain screws or panels. Check your owner's manual for further instructions. 


Refrigerator Repair

For the home, kitchen and beyond, Maytag manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Maytag appliance repair from experienced professionals, your local Appliance Helper can help.

Why is My Maytag Refrigerator Not Cooling? 
Condenser Coils are Dirty. The condenser coils are usually located under the refrigerator. They dissipate heat as refrigerant passes through them. If the condenser coils are dirty, they won’t dissipate the heat effectively. As debris builds up on the coils, the refrigerator becomes less efficient, causing the refrigerator to work harder to cool down. If the coils are significantly dirty, the refrigerator will not be able to maintain the proper temperature. Check the condenser coils to determine if they are dirty—if the condenser coils are dirty, clean them. 

Maytag Refrigerator water dispenser not working 
Water Tube in Door is Frozen. To determine if the water supply tube is frozen, disconnect the tube at the bottom of the door and blow air through it. If air does not pass through, this indicates that the water supply tube is frozen. If the water supply tube is frozen, thaw it out. In addition, ensure that the freezer is kept at the proper temperature. The freezer temperature should be kept from 0-10 degrees Fahrenheit. If the freezer is too cold, the water line may freeze. 

My Maytag Ice Maker is not Working 
Freezer Temperature is Above 10 Degrees F (-12C). If the freezer temperature is above 10 degrees Fahrenheit (-12C), the ice maker will not produce ice cubes efficiently. The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly. If the freezer temperature is too high, ensure that the condenser coils are clear of debris and the condenser fan is working properly. In addition, check to see if frost has accumulated on the evaporator coils. If the evaporator coils are frosted over, part of the defrost system has likely failed. 

Maytag Refrigerator ice dispenser not working 
Dispenser Control Board. The dispenser control board governs most of the functions of the dispenser system. If the control board is faulty, it may stop supplying power to the entire dispenser system. If only one dispenser part is not working, test each of the dispenser components before testing the control board. It is more likely that a single part has failed. If the entire dispenser system is not working, the control board is more likely to be at fault. 

Maytag Refrigerator not defrosting 
Defrost Control Board. The defrost control board determines how often to run the defrost cycle. If the board fails, the refrigerator will not go into the defrost cycle. Before replacing the defrost control board, first test the defrost heater and defrost thermostat. If the defrost heater and defrost thermostat are working properly, the defrost control board is likely defective. 

Maytag Refrigerator is noisy or loud 
Fan Blade. If the refrigerator is noisy or loud, especially when one of the doors are opened, either the evaporator or condenser fan blade may be at fault. First, check out the evaporator fan blade in the freezer behind the back panel. Try turning it by hand. If the fan blade does not turn freely, check to see if the blade is rubbing against something or if something is caught in the blade. Additionally, check the condenser fan blade in the back underside of the refrigerator to determine if it has any obstructions. 

Maytag Refrigerator defrost drain clogged 
Clogged or Freezing Defrost Drain. The defrost drain might be clogged or frozen. If the defrost drain is frozen, the water will overflow the drain trough and drip down to the bottom of the compartment. If the defrost drain is frozen, thaw it out and ensure that the drain is clear of debris. 

My Maytag Refrigerator is not Cooling 
The Evaporator Coils are Frosted Over. The defrost heater assembly turns on a few times throughout the day to melt away any frost that may have accumulated on the evaporator coils. If the defrost heater assembly is defective, frost will continue to accumulate on the evaporator coils, and the coils will become plugged with frost. If the evaporator coils are frosted over, the airflow through the coils will be restricted, causing the refrigerator not to cool. Check the evaporator coils to determine if they are frosted over. If the evaporator coils are frosted over, test each component of the defrost system. 

Maytag Refrigerator leaking water 
Clogged or Freezing Defrost Drain. If the defrost drain is frozen, the water will overflow the drain trough and drip down to the bottom of the compartment. This water can eventually leak onto the floor. Check the defrost drain to determine if it is clogged or frozen. If the defrost drain is frozen, thaw the ice. In addition, flush the drain with hot water to ensure that it is clear of debris. 


Washer Repair

For the home, kitchen and beyond, Maytag manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Maytag appliance repair from experienced professionals, your local Appliance Helper can help.

My Maytag washer won't spin 
Lid Switch Assembly. The lid switch assembly prevents the washer from spinning when the lid is open. If the lid switch assembly fails, the washer will not spin. To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity. If the lid switch does not have continuity, replace it. 

My Maytag washer is making a loud noise during the spin cycle 
Bearing. The tub bearing is mounted in the middle of the outer tub. The tub bearing helps to keep the inner tub spinning smoothly. Replacing the tub bearing is a very involved repair and will require disassembling most of the washer. If the tub bearing is defective, we recommend replacing both the outer tub and bearing. 

Maytag Washer won't agitate 
Agitator Repair Kit. If the washer won't agitate, replacing the agitator repair kit may solve the problem. The kit contains the agitator components that are most likely to wear out and/or fail. If any of the parts are worn out, stripped, or damaged, replace the kit. 

Maytag Washer won't drain 
Drain Pump. Sometimes, small objects or articles of clothing can get caught in the drain pump. To determine if anything is blocking the drain pump, remove the drain pump and check the pump for obstructions. If the drain pump is clear of obstructions, but is still noisy during the drain cycle, replace the drain pump. 

Maytag Washer vibrating or shaking 
Shock Absorber. One or more of the shock absorbers might be broken or worn out. The shock absorbers dampen the vibration of the washer tub. If one or more of the shock absorbers are worn out, the washer will vibrate or shake. Sometimes, when a washer is moved to another location, the shock absorbers can separate. Check the shock absorbers to ensure that they are positioned correctly, and inspect them for damage and wear. If one or more of the shock absorbers are broken or worn out, we recommend replacing all of the shock absorbers as a preventative measure. 

Maytag Washer fills slowly or will not fill at all 
Water Inlet Valve. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the wash may fill slowly or not fill at all. The water inlet valve requires sufficient water pressure to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve. 

My Maytag Washer is Leaking 
Drain Pump. The drain pump pumps water out the drain hose. If the drain pump is cracked or damaged, or if the bearings are worn out, the drain pump may leak water. The drain pump is not repairable—if the pump is leaking water, replace it. 

Maytag Washer won't start 
Timer. The timer is frequently misdiagnosed—before replacing the timer, first check all of the more commonly defective parts. To determine if the timer is defective, consult your washer’s wiring diagram and use a multimeter to test the timer for continuity. 

Maytag Washer won't spin or agitate 
Drive Belt. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. 



Maytag Appliance Repair

Maytag appliance service

Maytag appliance help

Maytag appliance assistance

Maytag appliance maintenance


Product Reviews:

Maytag is supposed to be the best. I wanted a top loader again. This washer
Maytag is supposed to be the best. I wanted a top loader again. This washer is almost worthless because of the water control. I have to add buckets of water before I start the washer. Otherwise the clothes are not clean. The cycles are strange with the amount of agitation. I will continue looking for an OLD model. DO NOT BUY THIS WASHER.
Published: April 6, 2019
K of Gypsum, KS
Source: consumeraffairs.com

We had an old Maytag that we loved but Judy wore it out. Bought the new May
We had an old Maytag that we loved but Judy wore it out. Bought the new Maytag & dont like it at all. Takes forever to wash 1 load & never enough water in tub to clean anything. Cant regulate water level, time or cycles. Hate it but what can you do?
Published: February 7, 2019
James of Takoma Park, MD
Source: consumeraffairs.com

My husband and I purchased a brand new Maytag dryer in January 2012. Our fi
My husband and I purchased a brand new Maytag dryer in January 2012. Our first issue came when the sensors went out in March; then the belt slipped off the drum in June; then the thermistor was defective in July; and now, the same thermistor code has popped up twice since replacing it. I cannot afford to go to the Laundromat all the time thats why we bought a new dryer. Please give me a refund so that I may buy a different brand. Model number: MGDB850WR0, Serial #: M10301051
Published: August 10, 2012
Carrie of Deer Park, TX
Source: consumeraffairs.com

I have a Maytag Performa washing machine (model no. PAVT234AWW) and called
I have a Maytag Performa washing machine (model no. PAVT234AWW) and called the Maytag parts department to order a plastic pulley for the main drive motor. I was told I would have to purchase the 189 dollar motor just to get the plastic pulley. After two days web searching and calling local appliance stores I found that Whirlpool who uses the same drive motor sells the pulley (part no. 21001108) for 9 dollars. The Whirlpool pulley is even made out of stronger plastic. I just wonder how many Maytag customers have had to purchase a drive motor like I was told I had to by Maytag just to fix a 9 dollar pulley. I got lucky and my problem was solved, but only because a local store happened to have this particular problem so frequently that they were able to help me out when Maytag should be the ones helping out their customers better. Thank you for your time.
Published: August 10, 2015
Bill of Marietta, SC
Source: consumeraffairs.com

I purchased a very expensive set of Maytag washer & dryer (topload wash
I purchased a very expensive set of Maytag washer & dryer (topload washer) and heavy duty larger capacity. Firstly- I purchased this through Home Depot on Labor Day weekend and did not receive this set until December 2020. This set has all the electronics and Im going to tell you NOT to purchase either one. The dryer MUST have a metal solid vent. This sets your dryer out into the walkway of a laundry room. If you use a heavy flexible metal vent; your sensor will be going off constantly telling you your vent is plugged and to clean it. I had a dryer vent company out twice to clean and inspect the wall & roof vents yielding nothing. I also have a dryer vent cleaner which I hook up to my vacuum and I clean the dryer vent monthly. If you lose power. You will need to unplug your dryer and let it reset to be able to use it.The washer is also terrible for the outrageous price. Again; glass heavy duty top load with all the electronics. You cant get the washer to fill even on deep fill. Also; do NOT put a lot of clothes or jeans or blankets in this machine. It will not be able to level and spin. When you try to use the drain and spin cycle; the sensor keeps going off. I swift the contents around and around and finally end up having to take soaking wet cloths out into the garage until I have one sheet in the machine and it will spin out. In addition- the CLEAN with Afresh mess. This forces you to clean your machine- whether you are in the middle of trying to get clothes drained or not.Buy something thats a simple workhorse with one button. Stay away from any bells and whistles because its only going to cause you heartache in the long run. I wish I would have read reviews prior to spending $1,700 on a Maytag Washer Dryer set (ON SALE- for God sakes). This is the biggest piece of garbage I have ever purchased. Buyer beware.
Published: June 22, 2021
Donnasue of Fort Myers, FL
Source: consumeraffairs.com

I have the Maytag Direct Drive Motor washing & dryer set the is suppose
I have the Maytag Direct Drive Motor washing & dryer set the is supposed to be “commercial technology.” The washer is supposed to keep wet clothes fresh if they don’t make it to the dryer right away. After 2 years, I disagree in that it offers no better outcome than the much older machine I replaced. Furthermore the dryer cuts off leaving my clothes damp every single time, which I cannot stand. It leaves my clothes to wrinkle terribly and damp to stink if I do not collect them fast. I honestly wish I still had my old set. All the new features simply fail to measure up not to mention over complicate and add expense to repairs.
Published: May 19, 2020
Sheri of Montgomery, AL
Source: consumeraffairs.com

Bought this Maytag washer from Sears and the salesman told us it was the be
Bought this Maytag washer from Sears and the salesman told us it was the best washer on the market. Well the Maytag washer is a dud. It leave residue on clothes, clothes come out very wrinkle. This washer does not even have a filter. I would not recommend this washer to anyone. We are very dissatisfied. We dont blame Sears, we blame Maytag for even thinking about putting this washer on the market - Maytag model mav7757aww
Published: January 21, 2014
roy of Virginia Beach, VA
Source: consumeraffairs.com

This is just a heads up to anyone thinking about purchasing the front loadi
This is just a heads up to anyone thinking about purchasing the front loading Maytag Neptune washer and dryer. We spent $1900.00 on these machines and have had nothing but trouble from them. I will never purchase a Maytag or now, Whirlpool appliance again. As to the rating above, if I could post negative 150 stars I would. I have spent as much in repairs as the new dryer cost.
Published: August 22, 2011
Ruth of Mcleansville, NC
Source: consumeraffairs.com

I owned my double oven Maytag Gemini for 14 months and I was absolutely sat
I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.
Published: July 15, 2013
Michael of Vallejo, CA
Source: consumeraffairs.com

Maytag and Home Depot do not back their products or assist customers. While
Maytag and Home Depot do not back their products or assist customers. While repair my fathers home in Grand Junction Colorado, Home Depot workman grabbed the 30 year old washer and dryer by the controls and promptly destroyed the machines. No - Home Depot didnt do anything despite complaints. I bought a brand new Maytag Washer and Dryer for the Grand Junction, Colorado home. The famous Maytags that are called dependable only lasted 3 months. When I went to complain at the Grand Junction Home Depot - the manager - Cheryl - called me a lair when I said I left phone messages for her. Cheryl seems to represent the best of Home Depot when she doesnt assist customers - is nasty and calls them liars when they say they left phone messages for her. No - Home Depot would not back their selling Maytag, and worse, they wont assist you in finding how to contact Maytag. Cheryls response was - Contact Maytag. Good bye. I was not given a contact or phone number - nothing. I spent over $32,000 at Home Depot fixing up my fathers home and rentals and this is how Home Depot treats customers. Worse I have a worthless Maytag that ceased working after just 3 months. Yes - you may contact me, yes - you may use my name and yes - I will blog on the internet the nastiness of Home Depot in Grand Junction, and the poor quality and poor customer service with Maytag.
Published: November 16, 2017
Janet of Durango, CO
Source: consumeraffairs.com

We purchased all new appliances 3 years ago including a Maytag dishwasher.
We purchased all new appliances 3 years ago including a Maytag dishwasher. Same problem as a lot of others. We had the control board fail three times in just four months. Now today the repairman came and while he was here contacted other Sears technicians and Whirlpool technicians. They came up with the idea to replace the detergent dispenser which they said is causing the main control board to fail. However, while the tech was on the line with Sears and Whirlpool they done troubleshooting on the detergent dispenser and found that it was all within specifications. In fact, that was not a problem because it worked as it should. But in their wisdom they decided to replace the detergent dispenser. We now have to wait another ten days for the part to arrive and reschedule another appointment to have the detergent dispenser that works replaced. The serviceman that was at our house said that they are making him replace a part that is working and that this does not need to be done but he has to take instructions from Sears technicians. Our service person said that he doesnt anticipate that replacing the detergent dispenser will make the dishwasher work but he said if it does it will only last a few weeks as before and then fail once again. We have the dishwasher on extended warranty and there are about 22 months. I suspect that this one will be going to court to get resolved. Never Maytag again or Whirlpool.
Published: July 22, 2016
Jim of Torbay, NL
Source: consumeraffairs.com

Have had problems with the set since day one. Bought brand new from Home De
Have had problems with the set since day one. Bought brand new from Home Depot. Got a great deal and now know why. Never cleaned the clothes properly, water marks on so many items, musty smelling regardless of how many times we cleaned it, horrible at removing stains, and finally not even 5 yo the motor stopped worked. The dryer has been repaired too and hasnt ever done a stellar job. Will never buy another Maytag product again!
Published: September 25, 2015
Andrea of Overland Park, KS
Source: consumeraffairs.com

Maytag Neptune Stacked Electric Washer & Dryer. Had to buy a motor for
Maytag Neptune Stacked Electric Washer & Dryer. Had to buy a motor for Washer but lasted 12 years before giving problems again; then couldnt find anyone that would service for cheaper than $100 for just coming to your house plus $75 an hour for labor. Thats HIGHER than my billable rate! Rip-off Service & parts charges. Found out it was easier & cheaper to troubleshoot ONLINE myself using FIXYA site and others. Expense for an appliance above what most run ~ 1500 for both units. Plus if it doesnt have or offer a 5-year warranty then something is wrong with the quality! Maytag Neptune Series MLE2000AYW 27 Inch Electric Laundry Center with 3.34 Cu. Ft. Washer Capacity, 4 Wash Cycles and 6.0 Cu. Ft. Dryer Capacity, 3 Dry Cycles: White. Worst part on this model was a WAX MOTOR that they used for the Washer to control the door being closed or open. Next worst DESIGN error was they didnt put a drain hole in the plastic rim seal for the Washer door, that area would build up mold & mildew if you didnt learn to keep Washer door open at all times AFTER a wash. We learned by removing the light bulb! Therefore it was easy for my crew to learn to leave the door open after washing. This model was Energy star certified and had a long life here 12 years. Unfortunately I think they build these things to only last 10 years; then you have to replace them. In years gone by... the 1970s Washing machines and dryers would last 20 years!!
Published: April 20, 2016
C of Other
Source: consumeraffairs.com

I purchased My Maytag Washer and Dryer set from Lowe's, which was a ve
I purchased My Maytag Washer and Dryer set from Lowe's, which was a very good experience all the way, back in June 2017. After two years I can finally give an honest review. We love this set even though it is not as quiet as the old Maytag washers. Still is but not as. We have not had one bit of trouble from either the washer or dryer. The next size larger would have been the better choice for us since we now have king size bedspreads to wash. It still does the job though, just one piece at a time. A lot of people complain about the smaller amount of water used but it still cleans clothes quite well. If you need more water just use deep water wash or for even more water use the setting for bulky sheets which really fills up the water level.
Published: May 24, 2020
James of Springfield, Missouri
Source: consumeraffairs.com

We purchased washer at Sears 6 years ago. Have had same issues for 5 or mor
We purchased washer at Sears 6 years ago. Have had same issues for 5 or more years. Sears has been out to check it 6 to 7 times! They clean it out, tell me to use (expensive) Affresh tablets monthly, problem solved but it never is! When we run our washer and walk in laundry room it smells like a sewer. If we open lid its even worse. I use Norwex all naturally, biodegradable laundry detergent. There is nothing Ive done to create this smell. Its a manufactured problem that probably relates to ALL the other issues with this crappie washer that Maytag will do nothing about. I called Sears for 7th or 8th time, said they could send someone out AGAIN, I said thats a waste of my time and yours. They told me to call Maytag. They wont do anything (warranty is up). Of course there are NO ISSUES OR RECALLS on this washer and obviously there should be with not ONE good review! Im angry. You all should be too. We paid good $ for a product that used to have a good name and they are screwing us. I think we should ban together with a class action lawsuit. Please give me your thoughts. They know something isnt right and they shouldnt get away with this.
Published: June 4, 2015
joanne of Center Point, IA
Source: consumeraffairs.com

I love the fact that there is no agitator in this machine. It give lots of
I love the fact that there is no agitator in this machine. It give lots of room when washing bulky comforters. I also love the vast amount of settings for load size and the soil settings. The con of this washer is that it has broken down on us twice in the 2 years since we purchased it. The pump has gone out both times. Unfortunately it looks like we will be making a purchase of a new washer in the near future because another mechanical issue has arose.
Published: May 9, 2020
Tammy of Pembroke, GA
Source: consumeraffairs.com

Well bought this washer a little over 1.5 years ago in 2017. The display st
Well bought this washer a little over 1.5 years ago in 2017. The display started going haywire, flashing, going on and off and would only go to the normal setting, most of the time. Called Maytag and had service come out and Maytag would cover parts and labor. Turned out the control panel went bad. About a week later found out today part was still back ordered and not available with no ETA. So was told Maytag would replace the unit. So until I find out whether or not they will actually replace it, Im giving one star. Been holding for customer service for over 35 minutes now to verify what I was told. Its a shame because this washer was given a good review. It is a front loader.
Published: October 15, 2018
Janice of Vienna, VA
Source: consumeraffairs.com

Maytag Centurian is a terrible product. I dont think the designers of this
Maytag Centurian is a terrible product. I dont think the designers of this model have ever washed and dried a load of clothes. Washer problems: The lid (top loading) locks so user unable to determine if the correct amount of detergent is being used. There is an unlock button, but it takes quite a long time to unlock (maybe 15 seconds), then an even longer time (seems like a minute or 2 to restart). The machine is LOUD and at one point in the cycle BANGS. I actually returned the first as defective, but when the 2nd machine made the same noise, I was told, no, thats the way it is. It seems to take much longer to wash a load than my previous machine. The Power Wash tears my clothes. Even the regular wash puts holes in my thin tee shirts after a few washes. Really had to get spots out. I almost have to hand wash to get the spots out BEFORE putting in the machine. Dryer Problems: Takes 70 minutes or more to dry a normal load with a couple of towels. The cover to the lint catcher doesnt seem to be properly sealed. Lint particles get all over the top of my dryer. I bought this Washer/Dryer combo last year. Im annoyed every time I do laundry.
Published: April 29, 2016
A. of Safety Harbor, FL
Source: consumeraffairs.com

I hate this machine: Maytag bravo xl washer. Clothes come out extremely wri
I hate this machine: Maytag bravo xl washer. Clothes come out extremely wrinkled, drum so deep can barely reach bottom on my tip toes & Im 57 & clothes dont come out clean. I cant wait to replace it!!! Why are clothes so wrinkled, I want to hang dry things & everything has to be ironed.
Published: August 16, 2015
Paula of Ocala, FL
Source: consumeraffairs.com

Horrible washing machine. Cannot get clothes clean. It simply does not supp
Horrible washing machine. Cannot get clothes clean. It simply does not supply enough water to wash. Have tried everything. I want my money back. How do you start a class action lawsuit. Thousands of people are dissatisfied also.
Published: August 19, 2018
Wendell of Aberdeen, SD
Source: consumeraffairs.com

Less than 2 yrs old and starts giving UL error on spin cycle. I try replaci
Less than 2 yrs old and starts giving UL error on spin cycle. I try replacing the springs. No relief. Notice dark brown fluid under dryer. Thing sound like a plane taking off. A little more research and Im thinking its the bearings. Looks like an expensive repair, now I have to decide whether to cut my losses. Seriously? The reviews on here are just horrible, not like this was an dl hell machine.
Published: May 6, 2015
Shawn of Dorr, MI
Source: consumeraffairs.com

Have had the top freezer Maytag refrigerator for several years now, and it
Have had the top freezer Maytag refrigerator for several years now, and it has performed great. Exterior is easy to keep clean, and the interior shelves come out easy for washing. Three drawers for fruits, vegetables and meat/cheeses work out great, and keep those products at the correct temperatures. Settings for both freezer and refrigerator are easy to see and change, if needed. Would buy another Maytag unit. Easy slide out for cleaning coils behind the unit.
Published: September 1, 2019
Mary of Port Washington, WI
Source: consumeraffairs.com

Purchased this Calypso machine as a second machine for my ranch to handle r
Purchased this Calypso machine as a second machine for my ranch to handle really dirty clothes. Purchased from Sears Outlet as a refurb machine would be fine for the purpose. Machine was alleged to work by Sears. Paid several hundred for the machine, brought it home, and voila it does not work. New hoses, ran all the checks, and will not fill. Called Sears and, despite the statements of the manager, was told that I have to have a 3 day old machine repaired and not replaced. This POS did not even work out of the box. Years ago I had a Calypso which is now a flower pot. Junk, Junk, Junk. NEVER buy anything from Maytag or Whirlpool.
Published: March 3, 2017
Denis of Lancaster, CA
Source: consumeraffairs.com

Just like so many others, our Maytag 300 Quiet Series, just 2 years old, ha
Just like so many others, our Maytag 300 Quiet Series, just 2 years old, has a malfunctioning control panel. Repairman told us this has been an ongoing problem with Maytag dishwashers. Steam/water gets into the control panel.For a while it worked on and off and now it is dead. I am saving up to do the repair, but in the meantime the dishwasher sits idle.
Published: September 24, 2011
Lauren of Pittsford, VT
Source: consumeraffairs.com

Purchased a Maytag dishwasher 1 1/2 years ago and the panel went out. I pai
Purchased a Maytag dishwasher 1 1/2 years ago and the panel went out. I paid $550.00 for this item, wanted to get a nicer one hoping it would last. Of course they only have a year guarantee for parts and Labor. Will not buy another Maytag appliance again!!!
Published: March 3, 2014
Richard of Washougal, WA
Source: consumeraffairs.com

The ranges are getting great but are more so with digital than buttons and
The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.
Published: February 11, 2017
Elizabeth of Springfield, MA
Source: consumeraffairs.com

DO NOT BUY A MAYTAG BRAVOS MCT WASHING MACHINE!!! I have had the machine fo
DO NOT BUY A MAYTAG BRAVOS MCT WASHING MACHINE!!! I have had the machine for two and half weeks, it HAS NOT WORKED EVEN ONCE!!! Service was scheduled - again for a BRAND NEW machine - through Maytag/Whirlpool - and the service ordered never happened. We waited an entire day, 8 am - 4 pm, only to discover the service desk of Maytag doesnt work either. My service is now booked for another week away and I am working on returning this AWFUL Maytag washing machine which never worked even one time!!! Warning: Do not buy Maytag/Whirlpool appliances!!
Published: January 4, 2018
Tracy of Oak Park, MI
Source: consumeraffairs.com

Frigidaire makes a good fridge. It works good. It has an alarm when you lea
Frigidaire makes a good fridge. It works good. It has an alarm when you leave as door open. Great appliance. If I could afford it Id get another one when this old model I have gives up on me.
Published: April 29, 2018
James of Charmco, Wv - West Virgin
Source: consumeraffairs.com

Purchased a new set of Maytag Bravos appliances in 2010. Washer lasted 3 ye
Purchased a new set of Maytag Bravos appliances in 2010. Washer lasted 3 years -- had a failed bearing and repairman said not worth fixing as tub would most likely also need to be replaced. Replaced with a new Speed Queen which has been operating trouble-free. Today dryer quit heating -- repair person stated it needs a new board -- not worth it to me. I am off to now purchase a new Speed Queen dryer. What happened to Maytag quality???
Published: March 10, 2015
Patrick of Noble, OK
Source: consumeraffairs.com

Worst product I ever purchase. I have four kids which are boys. This washer
Worst product I ever purchase. I have four kids which are boys. This washer does not clean very good. I usually soak the clothes first before I put it in the washer. Never purchasing their product again. Now I am stuck with this washer because I cannot afford to purchase another one. Hate it.
Published: April 18, 2017
Lakeesha of St. Martinville, LA
Source: consumeraffairs.com

We bought this Maytag dishwasher two years ago with a two year warranty. We
We bought this Maytag dishwasher two years ago with a two year warranty. We paid close to $700. Six months after we bought it, it started having problems on and off. They are including: leaking water, lights going on and off, cycles are not completed. We changed the console once, and soon after that it broke down again, and this time is out of warranty. Total repair times are: 6 times in two years. My husband call the company, asked them if there is a recall for this model? They told that there is no recall. Then the repair person came. According to his repair experience he said this is the common problem and he got a lot of calls for the same problem. If he told the truth about this, then the company was lying to its consumers!!
Published: August 16, 2015
waiwai of Ajax , ON
Source: consumeraffairs.com

We purchased our Maytag dishwasher (model MDB7609AWW2) on November 14th, 20
We purchased our Maytag dishwasher (model MDB7609AWW2) on November 14th, 2009 from a local appliance shop in White Plains, NY. Total purchase price was $449, not including tax.Sometime in November of 2011, the unit stopped working. I tried every simple test I could think of to hopefully reset the unit. Finishing the obvious checks, I researched some possible problems on the internet latch micro switch, drainage problem, dirty latch, etc. Frustrated as nothing got it working again, I called a repairman recommended to us by the appliance store.The repairman charged me $75 for the visit just to tell me that the control board is shot. Even worse, and this is the reason for this letter, the part costs $329 plus $40 in labor! That is outrageous! If you do the math, I am facing the costs of a brand new unit to fix the old one. That might make sense if the unit was 8 years old but it is barely 2.I have sat on the decision now for a few days as I am beyond upset and I never make good decisions when I feel like this. But to recap, Maytag manufactures an appliance where its basic function - turning on - fails in 2 years and the repair cost essentially totals (to use insurance parlance) the unit. I find this absolutely unacceptable.I don’t expect Maytag to do anything for me. But I will say this; I plan on letting everyone I know just how this experience went. To make things worse, I am willing to pay for a quality unit but how does anyone know what that is anymore? For color, my grandmother has a KitchenAid dishwasher from the 1970s that is still running fine. No membrane controls, no delay functions or fancy BS super sanitary cycles and guess what, it has no control board, just plain old dials and buttons. Imagine that mechanical control? Built to last unlike the junk you see today.To remedy, I plan on picking up a used machine from the classifieds. I’ll install it myself and be able to do this for 9 years at $449, assuming it only lasts one year (I’m finding these units for $50 used). I may get lucky and find an old one from the 70s that will last a lot longer than that.
Published: January 10, 2012
Tom of Briarcliff Manor, NY
Source: consumeraffairs.com

Refrigerator failed in less than 7 years. In August 2005, I purchased a new
Refrigerator failed in less than 7 years. In August 2005, I purchased a new Maytag side-by-side refrigerator to match the Maytag appliances (stove, microwave and dishwasher) in the new house provided by builder. In October 2011, I called a repairman because of noise. The relay switch was replaced for $179. Now, I am told the compressor and defrost circuit board need to be replaced for over $700. I will never buy another Maytag appliance or Whirlpool. They make and sell crap and dont stand behind their crappy products.
Published: May 17, 2012
April of Rio Rancho, NM
Source: consumeraffairs.com

Was so excited to get this machine so that I could wash larger loads, inclu
Was so excited to get this machine so that I could wash larger loads, including blankets, but unfortunately the machine didnt really clean as expected. That was very frustrating, but even more upsetting was when it began to sound like a jet engine when in the spin cycle. In researching this online, we have discovered that it is probably the bearings. When we called for service from the local store where we purchased the washer and dryer, we were told that it will likely cost at least $600 to repair. We have looked online to see if it is something that we can do ourselves, but really dont want to attempt this as it will require some heavy lifting and a lot of time. I am amazed that a machine like this would fail in such a short period of time and would like to add my name to the list of people who will not buy Maytag again! If a class action suit is ever filed against Maytag for this poor excuse for a washer, count me in, but unfortunately I will probably need to buy a new one before much longer.
Published: August 29, 2017
Nancye of Tallahassee, FL
Source: consumeraffairs.com

Washer model mvwc200bw1 c43942055 -Worst washing machine ever! The clothes
Washer model mvwc200bw1 c43942055 -Worst washing machine ever! The clothes come out all twisted together, I cant even see how the washer works because the lid locks when washing! The sound the washer makes while washing sounds like its barely even washing the clothes! I will never purchase any Maytag products and I wish I could return this one!! So disappointed, Im sticking with Whirlpool!! Plus the clothes dont even get that clean!!
Published: June 27, 2015
Steve & Joyce of Mount Juliet, TN
Source: consumeraffairs.com

I have a fairly new washer Maytag model #MHWE500VW serial #CSY0303991. I ne
I have a fairly new washer Maytag model #MHWE500VW serial #CSY0303991. I need Part # W10415587 doesnt excist for my washing machine anymore. Its been on backorder since Apr-May 2011. Maytag/GE insists that they are not responsible. As long as they can say backorder technically they are not liable for anything and dont really care that me the customer is having a problem and they Blatantly refuse to even investigate. I spoke with a GE supervisor just today and she basically told me wont help you because my appliance is out of warrenty. And she explained to my that my complaint will go into a file that no one will ever see. I searched the internet only to find hundred of other consumers are waiting for this same part. Ive called distributors & manufactuers. Same answer, backorder. My warrenty people are trying very hard to help me but again Maytag/GE refuse to help. Very dissappointed with this company. Wont be purchasing Maytag/GE products again. Wheres that guy in the commercial with nothing to do when you need him??
Published: July 14, 2011
Judy of Camarillo, CA
Source: consumeraffairs.com

Maytag French door, bottom freezer - Water accumulating on the freezer draw
Maytag French door, bottom freezer - Water accumulating on the freezer drawer gasket. After a short period of time, mold forms which is a potential health hazard. We asked Maytag to look at the problem. So far, 3 service people have come around - each one with a solution, but none have been successful. I called Maytag again and left messages on two different occasions, and they have yet to get back to me. Am I on the blacklist? This I know for sure - this is the last Maytag product to ever get in to my house again. If anyone has a solution to our problem, we would love to hear from you.
Published: December 4, 2012
Joann of North Fort Myers, FL
Source: consumeraffairs.com

I had a Maytag dishwasher that I purchased around 2005. I had no issues wit
I had a Maytag dishwasher that I purchased around 2005. I had no issues with it at all. Then, I got a notice that it was being recalled due to a fire hazard. My options were to either get a repairman to come out and fix it, or get a credit towards a purchase of a new dishwasher. I chose the second option. Even after getting a credit, the purchase cost was way more than my original dishwasher. I purchased the new dishwasher in June of 2010. Last spring (May 2012), I noticed a gap in my hardwood floors around the sink. A flooring rep looked around and said he would bet that theres a leak either at the sink or the dishwasher. I took off the front kick-plate to the dishwasher and discovered a wet spot. I monitored that area and discovered the leak coming from under the dishwasher (around the float switch). It wouldnt leak all the time, but every now and then, it would leak half to a full cup of water. I had the hardwood floor fixed (cost $350). At the same time, I schedule a service repair through Maytag. They sent a rep from a local repair company (Convenient Appliance Service, Inc.). The service rep couldnt identify the cause of the leak but said it was more than likely the seal around the door. So, I paid another $160 to get the repair done. I monitored the leak for a week and had no problems, so I put the kick-plate back on. In September 2012, I noticed a wet spot in front of the dishwasher. I took off the kick-plate and discovered that the dishwasher was leaking again. This time the leak was worse. It would leak 1 to 2 cups of water during a wash cycle. I called the repair company and they came out free of charge to take a look at it. The service rep said the float switch had gunk build up in it. He cleaned it out and said that should fix the problem. I monitored the area for 2 weeks and everything seemed to be fine. Last week (March 2013), I noticed some gaps in the hardwood flooring around the sink and dishwasher. I pulled off the kick-plate and discovered a wet spot. I ran the dishwasher and discovered that it leaked a ton of water (over 4 cups). I contacted the repair company that came out last time, and they said they would have to charge me $100 plus to come out and take a look at the problem. The rep recommended contacting Maytag. I contacted Maytag and they said I would either have to pay $129 for a service call (not including cost for parts), or $269 to get covered under their Repair Plus 1 program (everythings covered and it adds 1 year of warranty my dishwasher). I asked at what point Maytag would replace a dishwasher. The rep said when it is deemed unfixable. Other than that, they just keep coming out if I have issues. Part of me thought I need to cut my losses and just rip out the dishwasher and get a new one (cost somewhere around $700). But I went with the Repair Plus 1 program in hopes that they can resolve the issue. But Im definitely going to have to get the hardwoods ripped out again. It looks worse than before. It’s probably going to run another $500.
Published: March 11, 2013
Chris of Cary, NC
Source: consumeraffairs.com

I purchased a Maytag Washer & Dryer Bravos XL in 2013, the washer is al
I purchased a Maytag Washer & Dryer Bravos XL in 2013, the washer is already in the junk yard, the drive system failed, the bearings failed and it began to leak. The dryer had a main control board failed, I was able to purchase a new one and replace it myself. The board was made in China, the machines were assembled in Mexico. I replaced the washer with a heavy duty Speed Queen washer made in the USA!
Published: September 5, 2017
Junius of Greer, South Carolina
Source: consumeraffairs.com

We purchased our Maytag Refrigerator Model # MBF2258DEHM on 12/21/2015. Jus
We purchased our Maytag Refrigerator Model # MBF2258DEHM on 12/21/2015. Just a couple of issues I would like to bring to your attention before you purchase your Maytag. The single refrigerator door does not close automatically. You have to close the door. The metal handle is metal and has a metal smell and feel to it. The stainless steel door and the handles are not the same finish. Although this might not be a problem for some who like the industrial look I prefer my hands to be free of chemicals while I am preparing food. The ice maker takes up too much room. The ice maker should have been an option, not a standard item. I had a Kitchen Aid for 10 years and loved it. I thought I was going to have my Kitchen Aid for 15 years or more. I would have purchased another Kitchen Aid, but the reviews were not good.
Published: December 22, 2015
Chris of Norton, OH
Source: consumeraffairs.com

In 2003, I purchased a brand new Maytag washer and dryer set, I chose Mayta
In 2003, I purchased a brand new Maytag washer and dryer set, I chose Maytag because of their reputation. Within the first 6 months, I had a bearing go bad on it and that had to be fixed. It has become noisier and noisier throughout the years and now it is leaking all over the floor when I do a load. I am single, I live alone, I do laundry very seldom and do not do large loads. I am so disappointed with Maytag. When the repairman came out initially to fix it, he said that the brand he fixes most often is Maytag. Expensive lesson learned, Ill never buy any type of Maytag product again.
Published: June 4, 2014
K. D. of Newberry, FL
Source: consumeraffairs.com

Purchased a Maytag Bravos XL less than 3 years ago Model MVWB725BW0. We hav
Purchased a Maytag Bravos XL less than 3 years ago Model MVWB725BW0. We have had several repair calls. From reading complaints from others, I have the same: clothes balloon, clothes rip, dark clothes have a scum on them, even a blanket goes off balance and it is hard to start the cycle. It goes off balance all the time, makes a squeaky sound when agitating and the housekeeper can never figure out what cycle to run the clothes on because they always go off balance, there is a loud vibration, etc. The last repair call was for an actual leak on the floor! The appliance company charged us $95 for the service call, did nothing, and told us the parts would be more expensive than a new washing machine. Went to Home Depot today and purchased an LG washer and dryer for over $1500. I am not even going to try to recoup anything from Maytag because this is the second Maytag that I have had a bad experience with and didnt learn a lesson in the first place. Junk. :(
Published: January 16, 2018
Melanie of West Palm Beach, FL
Source: consumeraffairs.com

We bought a Maytag appliance package when we built our house in 2015. So fa
We bought a Maytag appliance package when we built our house in 2015. So far the exchange Fan burned out in the fridge. The element burned out on the range. The wheels broke off inside the dishwasher on the racks inside and the outside of the white dishwasher is rusting worse than 1959 Edsel. 3.5 years old. Broken and rusty. I called and emailed Maytag customer service and all they say is it’s out of warranty and they’re sorry. Things break I get it but if they said on the box when I purchased it that it would rust in 3.5 years I would have looked at and purchased another brand. Beware of the cheaply made poor customer service of the new Maytag.
Published: August 23, 2019
D of Big Lake, MN
Source: consumeraffairs.com

I would never buy a Maytag dryer again. It has been serviced 3x since purch
I would never buy a Maytag dryer again. It has been serviced 3x since purchasing in 2010.
Published: December 15, 2013
Londa of Philadelphia, PA
Source: consumeraffairs.com

The salesman tried to convince me to purchase a Bosch dishwasher, but I wan
The salesman tried to convince me to purchase a Bosch dishwasher, but I wanted one with a fingerprint-resistant finish. That narrowed my selection to several manufacturers. This dishwasher has a food grinder in it. It gets my dishes spotlessly clean, and I have been very happy with it.
Published: February 20, 2021
Renee of Tulsa, OK
Source: consumeraffairs.com

Same issue as everyone else. After about 15 months the control panel on my
Same issue as everyone else. After about 15 months the control panel on my Maytag dishwasher model#MDBH979SAM1 has malfunctioned. First it would only let me choose the rinse option but now all the lights are turning on and the dishwasher will not stop washing but yet the dishes are still dirty. I called Maytag and they quoted me 249.00 to fix the issue. But if its a common problem with this make and model why do I have to pay to replace the panel. They should recall this model or replace the panel with an updated one that wont have the same issues! I cant imagine paying 249.99 every year to replace this panel that seems to malfunction no matter what you do!!! I paid around 550.00 at the home Depot for this dishwasher! It did not even last me two years!!! I want a lawsuit filed against this company and I want my money back or my dishwasher replaced with one that works and wont have the same issues!!!
Published: December 8, 2014
Jessica of Yuma, AZ
Source: consumeraffairs.com

My Neptune has been a great washing machine. I did have to change the door
My Neptune has been a great washing machine. I did have to change the door gasket twice and just recently changed the bearings. My machine sounded like a jet engine. I ordered the parts on eBay, watched a YouTube video, and fixed my Neptune washing machine. Its still working and runs quietly.
Published: January 31, 2017
Jacqueline of New London, CT
Source: consumeraffairs.com

Belt broke in inside under tub after 13 months $150. Now another year and I
Belt broke in inside under tub after 13 months $150. Now another year and I am getting an error message F51 and it stops washing. Im done. Old Maytag lasted 14 years. This is done in 2. Im not paying any more to have it fixed for whatever F51 is. Im cutting my losses now. Hate this machine the way it washes anyway. Always feel like its gonna take off for Mars to join Matt Damon. HA. I try to laugh to stop being mad. Dont buy these. It gets no stars. And after reading other reviews, it deserves none. Shame on this company! Ugh, its making me put a star rating. But I say none.
Published: July 7, 2016
Kimberly of Belvidere, IL
Source: consumeraffairs.com

I bought a new stainless steel Maytag refrigerator last year. It had a one-
I bought a new stainless steel Maytag refrigerator last year. It had a one-year warranty. Wouldnt you know, 14 months after my purchase, the icemaker stopped working. Did not take out the extended warranty, as I thought I had purchased a quality appliance. I contacted the store where I purchased it. Was told it would cost $150 to replace. I have a feeling this appliance wont last very long. Suffice it to say, I will never purchase another Maytag appliance.
Published: January 12, 2015
Mary of Springfield, MA
Source: consumeraffairs.com

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled &a
Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.
Published: December 5, 2018
Janet of Blairsville, GA
Source: consumeraffairs.com

DO NOT PURCHASE UNLESS you want dirty clothes that smell.... Water level no
DO NOT PURCHASE UNLESS you want dirty clothes that smell.... Water level not correct, binding laundry together and replaced the same parts with cheap parts over and over... just wanted clean clothes in a no frills washer. NOT with this washer. Owned it 3 yrs and disliked it the first half washed load... $869.00 heap of junk.
Published: May 21, 2020
Mary Jo of Upper Sackville, NB
Source: consumeraffairs.com

Spent $2,000 on Maytag washer and dryer in September of 2020 thinking we we
Spent $2,000 on Maytag washer and dryer in September of 2020 thinking we were buying quality and a company that backs their products. Forward to January 2021 and were not able to schedule service through their website. Not able to get anyone to answer their phones. Called what used to be our local Maytag service and they told me Whirlpool took over Maytag warranty service and cancelled all the contracts for local repair shops. So, not only do we have a 4 month old washer I wish we had never bought, we cant even the Maytag to service it under their warranty! Never again...
Published: January 27, 2021
Quiteno of Fairfield, CA
Source: consumeraffairs.com

I have a French door fridge Maytag like everyone else. The bottom freezes o
I have a French door fridge Maytag like everyone else. The bottom freezes over and I have to de-ice it. Now the freezer doesnt want to cool. Its 3 years old. Total piece of junk.
Published: November 18, 2015
Ryan of Beaver, PA
Source: consumeraffairs.com

I bought a new smart washer and dryer from Maytag in mid-2019. Beginning in
I bought a new smart washer and dryer from Maytag in mid-2019. Beginning in the first few weeks the machine did not perform as expected--cut off in middle of cycle, door failed to unlock at end of a cycle, constant error messages that made no sense (power failure when power didnt fail, codes that arent defined in the owners manual). To make a long story short, the company that does their warranty repair, which has worked on the machine approximately 8 times, tells me there is nothing else they can do, the machine is a lemon. But their customer service department refuses to replace it. They say it must be repaired, yet again. But the parts are out of stock (which should be a pretty good indication that theres a problem with product quality). So I am to wait. How long? They dont know. Call again tomorrow.Do NOT buy a Maytag appliance. Customer service does not stand behind their products and the products are no longer up to the quality I had previously expected from Maytag. Additionally, telephone wait times on the customer experience line can exceed an hour and are customarily over 30 minutes. Never had an experience like this with any other major appliance customer service department.
Published: June 8, 2020
Fran of Greensboro, NC
Source: consumeraffairs.com

DO NOT BUY THIS MAYTAG REFRIGERATOR. Purchased 9-30-19. Delivered 10-4-19.
DO NOT BUY THIS MAYTAG REFRIGERATOR. Purchased 9-30-19. Delivered 10-4-19. 12-9-19 - Not Cooling, Called Whirlpool on hold for exactly 1 hour. 12-11-19 - Repair service here - ordered new Control Panel. 12-17-19 - New Control Panel Replaced. 1-6-20 - Freezer is not freezing. Control Panel going up and down and blinking constantly. Called Whirlpool - on hold for exactly 1 hour. They called service repair. 1-8-20 - Service Repair here and ordered 2 thermostats: 1 for freezer and 1 for refrigerator. 1-15-20 - Service Repair here to install 2 thermostats - At this time I purchased the extended warranty for $119.30 for 3 years.3-1-21 - Control Panel completely went out again. I called Whirlpool - on hold exactly 1 hour before they answer phone. I am so pissed. They call Service Repair. 3-3-21 - Service Repair here. They order new Control Panel. States these panels are continuously going out and they are having to replace them everywhere. 3-12-21 - I called Service Repair since we havent heard anything. ETA on control panel from Whirlpool is not scheduled until 3-19. I am really pissed by now.In the meantime I have been on hold with Whirlpool for 47 minutes. At exactly 1 hour being on hold, they answer my call. Im told I have to wait. There is nothing they can do. I told her we were buying ice every other day at $10.07 for 2 20# bags and they wont replace money. Told me to throw my items away and they would replace all the food for $250.00 one time during the 3 year contract period. The service is Customer service on their contract is terrible. Waiting for parts is even worse. This is a piece of crap appliance and we will never buy another Maytag.
Published: March 12, 2021
Richard and Sherrie of Herrin, IL
Source: consumeraffairs.com

One time at around yr 2 of our 10 yr warranty the repair guy removed my agi
One time at around yr 2 of our 10 yr warranty the repair guy removed my agitator, spline gone. Couldn’t find one anywhere! After a month of using a laundromat, I called the company in Montreal and they had the new agitator in my post office in 4 days. I am unable to wash anything that puts the Bravo washer out of balance ie: towels. The sides are busting out on the machine!! We have only had it 4 years so far. Not impressed! Does the warranty cover busting out sides? As it is a major part of the structure of the machine.
Published: December 21, 2018
Terry of Canada
Source: consumeraffairs.com

The microwave does everything I need and want it to do perfectly. It has ne
The microwave does everything I need and want it to do perfectly. It has never needed to be repaired or replaced in five years. We bought it on sale from Best Buy and consider it one of the best bargains we have ever made. Easy to operate, easy to clean, sleek and, for an appliance, quite personable. I find it refreshing to say something nice about an inanimate object.
Published: July 16, 2019
Barbara of Exton, PA
Source: consumeraffairs.com

My 20 yr old Kenmore washer broke last month so I replaced it with a Maytag
My 20 yr old Kenmore washer broke last month so I replaced it with a Maytag I bought from Lowes. I wanted a simple washer that would maybe last 10 years. The Maytag has a sensor for everything. So you can’t fill the washer, it determines how much water to use and it never fills enough to cover the clothes. It doesn’t agitate really. It’s more like a slow on & off movement. It does everything in an on & off way. The water fill goes on & off, it “washes” on & off. Even the spin is a spin, slow to almost stop - spin again - almost stop - spin again. It also stops filling if you open the lid, I tried to let some water fill before adding clothes (so the liquid detergent could dilute a bit) but every time I opened the top there was no water in the drum, I heated the water running and the drum was wet but it wouldn’t gill at all. I think it only puts water enough to “sense” the clothes have been soaked. I will call Lowes and try to return it.
Published: November 4, 2018
Coreen of Shirley, MA
Source: consumeraffairs.com

Maytag gas range 5 burners. Maytag is quality. Period. I doubt that other b
Maytag gas range 5 burners. Maytag is quality. Period. I doubt that other brands are made as well. From the handle of the oven door to the ease of cleaning the burners, you wont find better for the price. I look for quality and reliability. I read reviews. A deal breaker on any major purchased would be too many bad reviews and shoddy materials or construction. This range has 3 regular burners, one large burner and one small burner. The oven shelves easily adjust from one level to another. The controls are easy to reach and the timer and bake controls are easy to operate.
Published: March 16, 2016
William of Riverside, CA
Source: consumeraffairs.com

Side by side refrigerator model #msd255oveu01. I bought this refrigerator A
Side by side refrigerator model #msd255oveu01. I bought this refrigerator Apr. 2011... The 1st year, the ice kept sticking in machine or freezing up. Now they have had to replace the modules 3 times. Once fall of 2012 and and again yesterday, 3/19/14 and they had to come back today to replace that one. I have called Maytag and they wont stand behind it since the warranty is over. I have told them that this is an ongoing thing with the ice maker and I have had to have it serviced ever since I have bought it. I told them from the git go that the ice maker needed replace. The ice dispenser also drops an ice cube on the floor on occasion and if I use crushed ice it jams up. This product is defective and is not a good product.
Published: March 20, 2014
Mitzi of Lima, OH
Source: consumeraffairs.com

Maytag washer. The worst I have ever had... Never again. The tub does not w
Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.
Published: May 16, 2019
Gina of Duluth, GA
Source: consumeraffairs.com

We recently purchased a Maytag Washer/Dryer set, but shortly after it arriv
We recently purchased a Maytag Washer/Dryer set, but shortly after it arrived, we realized it was way too big for our needs, so traded it in for a smaller model (Model #MVWB765FC3). After a few washes, it developed a loud clicking noise during the entire wash cycle. Inquired about it at the retailer we purchased it from (showed them video of it) and was told it was not supposed to make that noise. Subsequently the Maytag Repairman paid us a visit and told us theres nothing wrong with the machine and that the retailer should not have told us what they did.#1). The machine did not make that noise initially. It started after a few loads of laundry. #2). The first machine we brought home was the same model (only larger) and that one didnt make that noise. To add insult to injury, the repairman has the audacity to tell my husband, Well, this visit didnt cost you anything. Really?! It cost him 4 hours of pay while he sat home waiting for you! In addition, we were delivered two cosmetically defective dryers that had to be returned. Furthermore, when I was washer/dryer shopping, I sent Maytags Customer Service Dept. an e-mail through their website asking questions about the product. To this day, I have still not received a response. I had a bad experience about 20 years ago with Maytag, but thought Id give them a second chance. I tell you...there will not be a 3rd time.
Published: June 4, 2019
Sue of Arlington, WI
Source: consumeraffairs.com

Our Maytag ref. is not quite 4 years old and it is leaking water on to our
Our Maytag ref. is not quite 4 years old and it is leaking water on to our floor. The ref. is a French door with water and ice in the door and freezer on the bottom. We have to clean up puddles of water at least 3 or 4 times a day. I see that this is not an isolated problem, as others have complained about this defect doing the same thing with their Maytag refs. Why hasn’t Consumer Affairs demanded a recall on these expensive defective refrigerators to date?
Published: October 23, 2016
Joseph of Derry, PA
Source: consumeraffairs.com

I spent a lot of money for top-of-the-line Maytag. It sanitized and worked
I spent a lot of money for top-of-the-line Maytag. It sanitized and worked to perfection. Delay wash, force wash, grinds everything you could possibly ever want. Fantastic and I can move the racks around. Beautiful. Stainless steel tub. Stainless outside. It has a ribbon cord in the controller. They didnt seal the controller head enough. So the dishwasher stops working after an almost guaranteed 2 yards from the ribbon cord rusting. Well you got to buy another one and it comes as a fill unit at 250 IF you replace it yourself. About 500 for a plumber. And you replace it every 2 years. Maytag is having class actions about it, it knew it has the problem. Its just very profitable to continue having the problem.
Published: February 24, 2016
Joanne of Washington, Washington
Source: consumeraffairs.com

After 2 years and 1 month, the machine stopped spinning the clothes on any
After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.
Published: January 12, 2015
Phyllis of Bellmore, NY
Source: consumeraffairs.com

Purchased Maytag dishwasher model # MDB4709PAB3 8/2012 @ Lowes in NY with e
Purchased Maytag dishwasher model # MDB4709PAB3 8/2012 @ Lowes in NY with extended warranty. After a while, noticed wood floor warping in front of appliance. Called repair and after several tries, they couldnt repair leak under door. After many complaints to Lowes and Maytag, was finally issued a new dishwasher 8/2013 same model #. Person that hooked it up couldnt wait around to see if all was okay. Ran dishwasher after he left and as usual for this model it leaks worse than before. Called Maytag complaint dept and they said they would issue me another dishwasher of my choice and same price through Lowes. But they never spoke to Lowes and Maytag will not call me back. I would think there must be a leak problem with this model. Do not buy. It is not worth the trouble!
Published: September 30, 2013
Blake of Islip Terrace, NY
Source: consumeraffairs.com

I bought the Maytag Bravos XL HE washing machine because I needed a machine
I bought the Maytag Bravos XL HE washing machine because I needed a machine that could handle large loads to save me time doing multiple loads for everyday items like jeans to towels, blankets as well as delicates. This machine is a COMPLETE disappointment. It does NOT get anything clean unless I wash it 4 times with bleach and pre-stain 4 times. You know what bleach does to your clothes! The water level is so low I can only wash 4 things at a time and I still have to wash additional times. It doesnt get the smell or food stains out. Not a good choice for an active family or person. Ive had clothes come out with suds still on them after washing three times. I use less than the recommended amount of HE detergent. There was a $250 agitator washer by GE at Lowes but it was smaller - how I wish I bought it. These impeller HE machines dont work. My advice steer clear of this Maytag product unless you like to waste your time re-doing loads of laundry.
Published: September 5, 2015
Cyndi of Lincroft, NJ
Source: consumeraffairs.com

In reading the reviews of a Maytag Dishwasher, I am also frustrated in the
In reading the reviews of a Maytag Dishwasher, I am also frustrated in the dishwasher is only 3 years old and the start button does not work. It cost $75.00 for the repair person to come in to take a look at it which they deduct from the cost, total repair cost $300.00. Did not make sense at this time to have to pay the $75.00 repair person and then purchase another $500.00 dishwasher so paid the total $300.00 hoping to get a few more years out of Maytag dishwasher. By the other reviews, may not be possible. Just very frustrating.
Published: May 20, 2014
Shar of Tonawanda, NY
Source: consumeraffairs.com

Bought a Bravos, large capacity, top load washing machine few years ago. (P
Bought a Bravos, large capacity, top load washing machine few years ago. (Purchased at a Lowes.) Been nothing, but one problem after the other!! I hate it! NO MORE MAYTAGS FOR ME. Has required several repairs of various parts. Now again, after being repaired few months ago, something else has gone wrong. Would have been cheaper to replace a 3-4 year old machine than keep having repairs.
Published: August 14, 2013
Renee of New Orleans, LA
Source: consumeraffairs.com

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home
In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.
Published: February 21, 2014
DONNA of Oakdale, CA
Source: consumeraffairs.com

I purchased both a Maytag washer and dryer and I am very disappointed in bo
I purchased both a Maytag washer and dryer and I am very disappointed in both products. Both appliances have electronic controls and are substandard. For the dryer if you do not touch the start area exactly right it will not start, can take multiple tries. For the washer, my town turned off my water to switch out the meter, once done the washer did not know how to clear the air in the lines and gave a LF error and no one at Maytag customer service could help me solve the issue and then could not set up a service call as their computers were down and did not have a process to call back the customer. This is terrible Customer Service - never again Maytag or any of their other products????
Published: March 3, 2020
Claire of Leesburg, FL
Source: consumeraffairs.com

My Maytag refrigerator, model number mff2557heb, serial number 10375839gv,
My Maytag refrigerator, model number mff2557heb, serial number 10375839gv, was purchased in 5/2005. Two weeks ago, this refrigerator stopped working. I called the Maytag technician and then right away came to my house and find out it is the compressor that needs to be replaced. He told me to search if it is under warranty. I searched in the internet Maytag compressor warranty and I found it and then called the Maytag representative. I told them I have found in their website that compressor of this Maytag is covered for 10 years but labor is not included. Then they asked me to fax it. I faxed the copy on 6/20 and they responded on 6/22. He said they received the copy and he said, Yes, it is covered for 10 years but you will shoulder the labor. So to make the story short, this Maytag representative scheduled Friday, 6/29 for the Maytag technician to fix my refrigerator. My husband did not go to work yesterday, 6/29, Friday, so he will be home for this Maytag tech. Maytag tech came at about 2pm yesterday and when he confirmed that it is the compressor that is the problem, he asked for the warranty paper. And when my husband present the proof, the copy of their warranty coverage that came from the Maytag website, he refused to work with my refrigerator because he said the one in the internet is not valid. It is really upsetting because I faxed the copy of it to them on 6/20/12 and they honored it. Thats why they arranged the technician to come to my house and then my husband did not work for them to work with our refrigerator and then asking me $79 for just saying that it is not covered by the warranty. I even gave them the model number and the serial number of the refrigerator so they can verify if it is covered. He said yes 10 years warranty on the compressor. In fact, two employees that I have spoken to both agreed that it is 10 years coverage except for the supervisor named Rachel. Her employees agreed to 10 years based on the paper that I have faxed them and it came from their website and they dont want to honor it after they sent the technician to my house. Thank you so much for your time and for reading about my grievances against Maytag employees.
Published: June 30, 2012
Raquel of Buena Park , CA
Source: consumeraffairs.com

Faulty control board. Have owned a Maytag dishwasher model MDB6769PASI for
Faulty control board. Have owned a Maytag dishwasher model MDB6769PASI for 2.5 years. The unit started beeping at random times for about a week - then went dead! Sounds like other reported failures and it is unlikely repairs will be permanent! Never again Maytag.
Published: February 20, 2017
Bill of London, ON
Source: consumeraffairs.com

In 2007, we bought a Maytag Neptune Washer Dryer Combo from Lowes. By 2008,
In 2007, we bought a Maytag Neptune Washer Dryer Combo from Lowes. By 2008, the washer started stopping operation at every rinse setting, requiring someone to constantly monitor the machine to assure that the button was pushed to fulfill the entire cycle. We called a repair company and were told that the machine was shutting down because the screen in the water intake was getting clogged with debris and was making the machine feel that the water was shutting off. Thus, according to the repair man, the machine was shutting itself off. He showed me how to clean the screens in the intake line and charged me about $150 for the service call. Within a week the machine was doing the same thing again. I pulled out the screens and they were clean. We continued to watch over the washer whenever it was doing the wash and continued to push the button to restart the machine. We live in a very rural area and there are really no repair services available without paying enormous fees just to get them to make a call and the wait is often more than a week.Shortly after the intake incomplete cycle problem, the washing machine stopped getting the water out of the clothes in the spin cycle, forcing us to wring out the clothes before putting them in the dryer. Then we noticed that the washer was leaking from the bottom rear all over our hardwood flooring. We went out and bought a new washer dryer based on reading consumer reports.The cost to replace this piece of crap from Maytag was in excess of $1600. We are only in this house part of the year so this Maytag product not only did not work very well over the short time that we owned it, but it was only being used for a few months out of the year. We have since learned that there was a class action suit over this product line and would like to know how to join the suit. We are so far out in the woods that we will not get our new washer / dryer until some 2 weeks out from our purchase. We have spent nearly $3,000 since 2008 on washer dryers, an average of $1,000 a year.
Published: August 21, 2011
William of Indian Lake, NY
Source: consumeraffairs.com

How is this fair that only a couple of washers recalled...I knew of no reca
How is this fair that only a couple of washers recalled...I knew of no recalls either...My old Kenmore top loader outdated by far. Guess I should have kept it.
Published: September 23, 2013
Gayle of Denham Springs, LA
Source: consumeraffairs.com

I bought my microwave in Nov of 2015. We began having problems in April 201
I bought my microwave in Nov of 2015. We began having problems in April 2017. When you cook or warm something up it gets hot. The light wont come on and the display continues to say open/close door. After about 4 hours of cool down time it may or may not restart. After contacting Maytag I was told I should have purchased the warranty. They also informed me that they do not have repairman in my area. We have just replaced all appliances with Maytag so now I am concerned they are all junk. We did buy warranties on the major appliances, but how will they repair with no repairman in my area. Maytag used to be the best appliances but after this experience and now I have a broken microwave after only a year and a half that they dont stand behind, I will never purchase any Maytag again. It also seems that this is not the only issue they are having with their microwaves. I have contacted my Lowes where we purchased and they even made a Maytag call with no results. Maybe the suppliers should stop promoting and selling their items. We replaced a 22 yr old Kenmore microwave that was still working thats why this is so heart breaking. Stand behind your products. No wonder you dont have repairman. They would never get a day off from repairing your junk.
Published: August 5, 2017
Jackie of Carrsville, VA
Source: consumeraffairs.com

Barbara ** purchased a Maytag Bravos X washer. The washer did not perform a
Barbara ** purchased a Maytag Bravos X washer. The washer did not perform anywhere near the advertised and EXPECTED performance. A letter was written to the Maytag Customer Center on July 12, 2014 complaining about the washers inability to clean or rinse clothes effectively. As of this date we have had NO direct contact from Maytag. After reading many reviews and noting that I have seen over 700 people which had issues with this machine, I wish that I had never purchased from Maytag. I have had to purchase a new machine to replace this useless Maytag. When I ask a used appliance dealer if he would be interested in purchasing my Maytag Bravos, his reply was, I dont want any Maytag Bravos in my store.I have made an effort to obtain some type of satisfaction from Maytag, but to no avail. I would like 100% refund for this purchase. If Maytag does not meet the expectations of its customers, then I feel that a class action law suit should be started through consumer affairs. When you cant even get a used appliance dealer to purchase a used Maytag Bravos, then there is a real problem with the product. The purchase price was $616.55. A total waste!!
Published: December 31, 2014
Jimmie and/or Barbara of Sevierville, TN
Source: consumeraffairs.com

Maytag Bravos Quiet Series 300 - Our motherboard on the washer went out aft
Maytag Bravos Quiet Series 300 - Our motherboard on the washer went out after 2 years from purchase - just out of warranty. Motherboard was $550 so we bought a Samsung. Now our dryer has gone out for the second time. First time was the pulley assembly came apart. We self-repaired after watching YouTube. Now the motherboard has gone out on the dryer! I will NEVER buy another Maytag product. They are a waste of hard-earned money and have left me with piles of laundry numerous times. Maytag, you need a class action suit filed against you!
Published: September 26, 2015
Robert of Buckeye, AZ
Source: consumeraffairs.com

My stove has been reliable and efficient. I bought it about 11 years ago an
My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.
Published: February 20, 2021
Valerie of Aberdeen, WA
Source: consumeraffairs.com

The Maytag Neptune TL washing machine has always been extremely loud! It sm
The Maytag Neptune TL washing machine has always been extremely loud! It smells awful and now our clothes too! I have found mold in the washer and cannot get it all out even with bleach. My children are extremely allergic to mold and they have had problems because of this. I am very disappointed in this washer and find it sad that no kind of action has taken place to help people who have bought them.
Published: September 4, 2011
Sarah of Rogers, AR
Source: consumeraffairs.com

I bought my Maytag in 2013. It worked fine at first but for the last year i
I bought my Maytag in 2013. It worked fine at first but for the last year it isnt getting clothes clean. In fact, some look like theyve never been washed. I have to run the rinse cycle 2-3 times and they still seem somewhat soapy. The washer still leaves clothes drippy after running the spin cycle. It takes 2-3 hours to complete a small load. I wish I had my old Kenmore back. It worked fine for nearly 20 years!
Published: August 11, 2015
Nell of St. Petersburg, FL
Source: consumeraffairs.com

A refrigerator we have had for just two years has been leaking water from t
A refrigerator we have had for just two years has been leaking water from the freezer and damaged our hardwood floor. We thought it was someone dropping ice or leaving the freezer drawer open but no, there is an admitted problem with the mechanism. No coverage from Maytag for the cost of fixing THEIR MISTAKE. The company doesnt seem to care. Got the run around from their management.
Published: October 6, 2015
Brenda of Killarney , MB
Source: consumeraffairs.com

This is the noisiest washing machine ever manufactured - cannot do laundry
This is the noisiest washing machine ever manufactured - cannot do laundry at night or no one sleeps, during the evening it overpowers the television. Dark washes are a nightmare as there is a white smear (soap scum?) on everything (guess you don’t see it on whites) - extra rinse does not help. What happened to this “reliable company”???
Published: November 20, 2017
Virginia of Ft. Myers, FL
Source: consumeraffairs.com

Purchased this machine to replace the recalled Samsung washer that was expl
Purchased this machine to replace the recalled Samsung washer that was exploding. I should have kept my Samsung. I loved it and had no complaints, but since there were reports of it exploding I took the rebate and purchased the Maytag Bravo Nightmare. Everything you have read or will read here is true. I would spend hours, I mean hours trying to do a load of laundry. If the cycle would complete itself, the clothes would be soaking wet, and they never smelled clean. I would try rinsing again and the cycle would start out with 18 minutes and I would return to the machine 1 hour later and it would be still running water and still have 18 minutes or more left. I watched it complete the spin cycle and start the rinse cycle again. We had the service guy out several times - he would call the techs and they would test the machine and say nothing was wrong other than it was off balance. They said I was using the wrong detergent - when proving that I was using an HE detergent, they counseled me on how to lay the laundry into the machine, and said I was using too much laundry detergent. After babysitting this machine for more than a year, and being told by Lowes Customer Service that the techs say there is nothing wrong with the it, I was fed up. I called Lowes and told them to send their techs to my house to do the laundry. I threatened to call for service every week until my extended warranty was exhausted. They finally gave me a merchandise card valued worth the purchase of the machine. Now, I have the painful decision of deciding what to buy next - It wont be a Maytag!
Published: April 13, 2018
Kathey of Wagram, NC
Source: consumeraffairs.com

I purchased a French Door, Bottom Freezer refrigerator in the summer of 200
I purchased a French Door, Bottom Freezer refrigerator in the summer of 2006. Less than 3 years later, the ice maker door kept opening and closing and the lights on the door panel kept flashing. I called Maytag and found out there was a problem with the circuit board, and that it was under recall. The refrigerator was fixed at no charge and I was happy. Approximately 2-1/2 months ago, less than 7 years after I bought the fridge, it started getting too cold inside and then too warm and then too cold, etc. Then it stopped cooling altogether. From what I read, it was either a problem with the compressor or the relay on the compressor. There was a recall on the relay on some models, but not on mine. I cant even afford a service call. Let alone a repair charge. If the compressor is the problem, Im looking at a repair bill in the hundreds of dollars. The online price for a compressor is over $300. I dont have the money. So the beautiful refrigerator that I paid $2,000 for sits in the kitchen, unplugged. I never figured that Id pay that kind of money for a refrigerator and have 2 major problems with it in less than 7 years. I just got off the phone with Maytag and, of course, they cant do anything to help me. I was hoping to never buy another refrigerator, but if I have to or if I have to buy any other appliance, I will never ever buy another Maytag or Whirlpool. I will post everywhere I can about my experiences with this refrigerator.
Published: June 4, 2013
Linda of Irwin, PA
Source: consumeraffairs.com

We purchased a Maytag Gas range MGR8674AB in November 2012. The contents of
We purchased a Maytag Gas range MGR8674AB in November 2012. The contents of the drawer (oven mitts, trivets, hot pads) caught on fire. As we pulled out the drawer, it scorched the front of the range.
Published: January 31, 2013
Erika of Pound, WI
Source: consumeraffairs.com

I have been the latest victim in purchasing a Maytag Refrigerator. Somethin
I have been the latest victim in purchasing a Maytag Refrigerator. Something needs to be done about the defective products they are putting on the market. I received 9/7/13 (yesterday) a new Model FW: 555 Complaints and Reviews about Maytag Refrigerators bottom freezer refrigerator. After being plugged in for 3 hrs, the temp was 60 degrees.. After 8 hrs same and 24 hrs same. I lost everything because of the defect. I notified the store 3 hrs after purchasing it and because I had it delivered on a Saturday I have to wait till Monday to get this resolved. I want everyone to read before buying a Maytag product.
Published: September 8, 2013
Grace of Monroe, NJ
Source: consumeraffairs.com

13 months after purchasing my Maytag dishwasher, it started operating by it
13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.
Published: June 29, 2014
Deb of Reeders, PA
Source: consumeraffairs.com

I bought two sets of Maytag washer and dryer. We have had them for less tha
I bought two sets of Maytag washer and dryer. We have had them for less than a year and the tubs had to be replaced out of both of them. Now, its less than six months later and they are doing the same thing, so the tubs have to be replaced again. What kind of equipment are you making? This is just an outrage. You are scamming people to buy your products by your so called advertising and rep. Well, this is false advertising on your part. I will never buy another Maytag anything or Whirlpool either. I also see there are a lot of others having the same thing being done to them. I would be ashamed to even have these products to sell. Shame on you. Scammer.
Published: April 11, 2013
Linda of Marengo, OH
Source: consumeraffairs.com

My Maytag refrigerator was purchased from Home Depot less than 3 years ago.
My Maytag refrigerator was purchased from Home Depot less than 3 years ago. It is a French door, bottom freezer draw model #MFI2569VEA1. Every four days, there is a huge puddle of water at the base of the unit and it is starting to ruin my ceramic tiles. I tried the online video solutions to no avail. Home Depot wont repair it, they told me to contact Maytag. Maytag wants me to purchase a $375 warranty, which is 30% of what I paid for the refrigerator. I will never buy a Maytag refrigerator again, or any Maytag product for that matter. They once stood for solid reliability and peace of mind, now you get a piece of junk instead. I cant even sell it on Craigslist if I wanted to because who would want it? If a class action suit is ever initiated, Ill be on board. I hope Consumer Affairs contacts me.
Published: February 4, 2014
Catherine of Bordentown, NJ
Source: consumeraffairs.com

Maytag 7000 series front loaders bought in 2013 on basis of high ratings fr
Maytag 7000 series front loaders bought in 2013 on basis of high ratings from Consumer Reports. Also durable and look good in the process. Had for 3 years. Machines highly rated by Consumer Reports and bought on sale. They were a very good value. Both W & D have steam feature but find Ive rarely used it. Durability is key, as is the ability to balance wide variety of loads, which our machines do well. Capacity of 5 cu ft or better sufficient for a household of 2. Maytag reputation for durability and reliability and made in US, though a clone of Whirlpool. These are big, heavy machines, best for side by side but they can be stacked. The units are quiet, have more features than weve ever used and so far have been reliable, gentle on clothes incl delicates and drum bearings really help with keeping loads balanced. Door hinges built like a tank but the chassis theyre attached to arent up to par. W & D have stainless drums. Washer is resistant to mold & odors but dryer lint system convoluted in design and hard to clean out.
Published: April 20, 2016
Greg of Green Valley, AZ
Source: consumeraffairs.com

My complaint sounds just like the others listed here. Purchased Maytag dish
My complaint sounds just like the others listed here. Purchased Maytag dishwasher MDBH979SAB1 at Home Depot 2/2013. In June 2014, the control panel started to malfunction. When I called Maytag, these were the options given: 1--have it serviced out of warranty at $89-$150 for repairmans trip & diagnostic, which doesnt include parts & labor or 2--obtain something called Repair plus one, which covers the cost of repair and reinstates the warranty for one year at the low cost of $264.95. So either way, Im going to have to pay almost 1/2 of the original purchase price. Ridiculous! We had our previous dishwasher (not a Maytag) for over 13 years, with only minor repairs. We purchased a Maytag because we thought it was a reputable company that stands behind their products---well dont believe it! I would NEVER recommend any of their products.
Published: September 19, 2014
Marguerite of Glenmoore, PA
Source: consumeraffairs.com

My husband bought a washing machine for me, February 2019, based on my requ
My husband bought a washing machine for me, February 2019, based on my request for a top load and a quick cycle time. The first issue was that the washer and dryer was the wrong color. I didn’t realize that he had ordered a stainless steel set before I accepted it. When he got home and discovered it, he called and tried to get the correct color, and Maytag refused to correct the mistake. When the technician starts the washer and dryer before they leave to make sure it’s working, it immediately becomes a used item that they can’t sell is what they explained to my husband! The technician also didn’t remove a plastic bag from the dryer vent that I asked him to check on before he attached the hose to the wall! Took me 2 days to figure out why the machine wasn’t drying the clothes properly!This Maytag washer has the longest quick washing time ever! 40 minutes! I have had trouble from day one with getting laundry clean with this brand new machine! And I’ve been washing clothes for almost 30 yrs! I discovered today that this washer only washes for 10 minutes in the soapy water and then begins draining! Unbelievable! This washing machine that takes 40+ minutes to complete a load of laundry! This is the worst experience I’ve ever had with a washer in 30 years of doing laundry! Don’t waste your money or your time even to look at this machine! It’s a poor buy!
Published: August 17, 2019
Tiffany of Ladson, SC
Source: consumeraffairs.com

We bought a top-loading Maytag washing machine in January 2020, and are ver
We bought a top-loading Maytag washing machine in January 2020, and are very disappointed. Clothes do not come out clean. We called the Maytag call-center and were told that “high efficiency machines are different”. They use much less water to be green, but now I have to wash items several times, negating any energy conservation. This also takes more of my time. If we use the “deep water” option and power cycle, clothes are almost clean; however, it takes 1 hour and 45 minutes per cycle. My 18-year-old Whirlpool washed clothes beautifully in under 45 minutes. This brand-new Maytag is NOT an improvement. We use the correct HE detergent and have tried with warmer water, and all of the different cycles, but still do not get acceptable results. The Maytag washing machine is not effective at the one thing it is designed to do, clean clothes. Our specific model is MVWC565FW1, however the saleperson told us that all models are similar.
Published: March 18, 2020
Lucia of Victoria, BC
Source: consumeraffairs.com

I purchased our Maytag Dishwasher in 2014 (Model # MDB77495B) and after a l
I purchased our Maytag Dishwasher in 2014 (Model # MDB77495B) and after a little over a year, of course after the warranty had expired the panel started to act up. I did get it repaired costing over $300 for parts and service thinking all is well. The repairman that came out had to come out twice once to look at and then again to fix after the part came in. We had a conversation and he said that was common with this brand, the steam sometimes affects the panel. I spoke with Maytag about getting an extended warranty but after looking at the cost passed on it. Well now the panel is acting up again. If Maytag thinks I am going to have another repairman come out well think again. I will see how much the part cost and do it myself if it cheap enough, if not I guess Ill be back to washing dishes by hand for awhile. I bought this brand feeling that it was American made and the cost was on the expensive side that it would last. I am disappointed that this has happened again. For the money spent it should last at least 10 years. My old dishwasher that was given to me used lasted over 15 years with not one problem. Its a shame we cannot get good working appliances as we did back in the day.
Published: July 22, 2016
Donna of Levittown, PA
Source: consumeraffairs.com

I am very frustrated and disappointed with all of the appliances I purchase
I am very frustrated and disappointed with all of the appliances I purchased from Maytag, 3 1/2 years ago. The stove has never cooked evenly, and they replaced both heating elements, and it still does not bake properly. I just called customer service, because my pies for the holidays burned once again. They told me there was nothing they could do. I cannot believe a customer that spent this much money with Maytag (purchased a washer, dryer, microwave and oven), gets no help from the company. The transmission has been replaced in the washer, and is still noisy. The dryer is also very noisy. The stove does not bake properly, and the microwave quit within a few months of purchasing. The quality of Maytag is very poor, and the customer service is obviously poor too, when they said there is nothing they can do for me. I guess they do not care about customer loyalty.
Published: December 28, 2011
Dean of Lawton, IA
Source: consumeraffairs.com

Maytag washer leaves clothes more wrinkled after a wash than they were in b
Maytag washer leaves clothes more wrinkled after a wash than they were in before being cleaned. And these are not full laundry loads. Then using the Maytag dryer is a joke. Need to run double times or extended times on most of the settings to get them completely dry. When it comes to the wrinkle free setting... what a joke. Clothes might be close to dry but wrinkled. Have always had Maytag products since forever. Tried Samsung for the last set-----washer lasted 6 years and then needed a full overhaul. Cheaper to buy a new set. Went back to Maytag. MISTAKE. Samsung did a lot better job of washing and drying. Now stuck with Maytag until... when? Retired and dont have the funds to get new replacements. Just my opinion though.
Published: February 12, 2019
Bob of The Villages, FL
Source: consumeraffairs.com

I have done widespread reading and realize that the front panel flashing an
I have done widespread reading and realize that the front panel flashing and a clanging noise coming from the fridge, as well as it not cooling or freezing or the water dispenser not working, is a common issue. My extended warranty had run out, and as I rely on the fridge given Im insulin-diabetic and have meds to store, I phoned Maytag to see if they would help regarding the part. No joy. It means that as I cannot to pay a repairman hundreds of dollars to repair it, I have to order the HV board myself and will attempt to fix it. I am hugely disillusioned with Maytag and would never recommend it to anyone.
Published: July 13, 2013
Fiona of Gadsden, AL
Source: consumeraffairs.com

I have a Model MBF 1958XES4 which I bought from Home Depot in June of 2012.
I have a Model MBF 1958XES4 which I bought from Home Depot in June of 2012. It has leaked repeatedly onto my wood floor. The water also collects and freezes on the floor of the freezer. I already have warped floor boards as a result. I just got it fixed. The repair person said he has done over 200 of these repairs in the last year. He also said Maytag knows its a defect and has supplied them with replacement parts. The company apparently tells its repair companies not to discuss this with their customers. I have yet to contact Maytag, although apparently from others experiences that will be futile. Im willing to join others in pursuing this. I had a 40 year old Kelvinator which was still working well which I replaced with this refrigerator when I redid my kitchen.
Published: September 5, 2014
Linda of Akron, OH
Source: consumeraffairs.com

I bought a every expensive Maytag Neptune (washer and dryer one unit) and i
I bought a every expensive Maytag Neptune (washer and dryer one unit) and it is now sitting in the carport. The washer broke and I had to have service people come to my house continuously. Over a period of 6 months I had to pay for 3 motor control boards plus service calls. Thats when I had I moved to the carport. In 2012 I bought a Whirlpool Duet washer and dryer so I would be able to stack them. I had to put them at Sears because I had to use layaway. I paid for them over 12 weeks and had to use a laundromat during that time. Last week I got a F01 E02 error code which means replace motor control board. These boards cost over $300 each not counting the cost to install it.I did talk to Sears since the washer was only bought 4 years ago. They were nice to me but could do anything for me. Truly sad when a washer only lasts 4 years for the amount of money I had to pay to purchase it. I dont know what I going to do now since I am now retired but I WILL NEVER BUY A WHIRLPOOL OR MAYTAG AGAIN.
Published: August 25, 2016
Martha of Julian, NC
Source: consumeraffairs.com

Visa MasterCard

Site Secured By The Website Guardian
TOP