Appliance Types


Appliance Brands


Article Categories


More Articles


Whirlpool Appliances
Whirlpool Appliances

Whirlpool Appliance Error Codes

The company markets Whirlpool, Maytag, KitchenAid, JennAir, Amana, Gladiator GarageWorks, Inglis, Estate, Brastemp, Bauknecht, Ignis, Indesit, and Consul. Their website also mentions Diqua, Affresh, Acros, and Yummly brands.


Air Conditioner Error Codes

CODE: UA. 
PROBLEM: Setting error, indoor and outdoor unit abnormal. 

CODE: E6. 
PROBLEM: Communication malfunction. 

CODE: PL. 
PROBLEM: DC input voltage is too low. 

CODE: PH. 
PROBLEM: DC input voltage is too high. 

CODE: F0. 
PROBLEM: Lack of Freon or block protection. 

CODE: P7. 
PROBLEM: Temperature sensor malfunction of carbon fin. 

CODE: UU. 
PROBLEM: DC overcurrent. 

CODE: P8. 
PROBLEM: Overheat of carbon fin. 

CODE: F4. 
PROBLEM: Break-circuit and short-circuit of outdoor condenser temperature sensor. 

CODE: F5. 
PROBLEM: Break-circuit and short-circuit of outdoor discharge temperature sensor. 

CODE: E4. 
PROBLEM: Discharge protection of compressor. 

CODE: F3. 
PROBLEM: Outdoor ambient temperature sensor malfunction. 

CODE: U5. 
PROBLEM: Current diction malfunction of complete unit. 

CODE: H7. 
PROBLEM: Sync failure. 

CODE: EE. 
PROBLEM: Storage slug. Indoor PCB malfunction. 

CODE: E2. 
PROBLEM: Anti-freezing protection. 

CODE: H4. 
PROBLEM: Overload of system. 

CODE: H6. 
PROBLEM: No motor of indoor unit feedback. 

CODE: F2. 
PROBLEM: Indoor pipe temperature sensor malfunction. 

CODE: F1. 
PROBLEM: Internal ambient temperature sensor malfunction. 

CODE: UF. 
PROBLEM: Zero passage abnormal. 

CODE: H3. 
PROBLEM: Overload of compressor. 

CODE: LC. 
PROBLEM: Startup failure. 

CODE: UH. 
PROBLEM: No motor of outdoor unit feedback. 

CODE: E5. 
PROBLEM: Overcurrent protection. 

CODE: U7. 
PROBLEM: 4-way valve conversion abnormal. 

CODE: U1. 
PROBLEM: Phase current detection malfunction of compressor.


Dishwasher Error Codes

CODE: 1-1 
PROBLEM: Electronic control board is detecting a stuck electrical relay on the circuit board 
FIX: Remove power to the dishwasher for 5 minutes to try and reset. If the error code comes back when power is applied then check the wiring and the components. If the wiring and components check out then replace the electronic control board. 

CODE: 1-2 
PROBLEM: All the lights are on as the user interface control is not compatible with the electronic control board 
FIX: This error code will show when the wrong user interface control is installed. 

CODE: 2-1 
PROBLEM: Electronic control board detects a stuck key button on the control panel 
FIX: If no keys work replace the electronic control panel. If the control panel is damaged then replace the electronic control panel. If the control panel is in working order then the problem may be within the electronic control board. 

CODE: 2-2 
PROBLEM: User interface control unable to communicate with the electronic control board 
FIX: Remove power to the dishwasher. Check the wiring between the user interface control and the electronic control board. If the wires and connections check out then replace the user interface control board. If the problem comes back then replace the electronic control board. 

CODE: 3-1 
PROBLEM: There may be a break in the electrical wiring OR the thermistor (water temp sensor) component failed. The optical water indicator that detects the amount of debris in the water may have also failed. 
FIX: Remove power to the dishwasher and check the wiring for the thermistor and optical water indicator circuit. If the circuit wiring checks okay then replace the thermistor and optical water indicator component. 

CODE: 3-2 
PROBLEM: The Thermistor / Optical Water Indicator circuit is electrically shorted 
FIX: Remove power to the dishwasher and check the wiring for the thermistor / optical water indicator circuit. If the circuit wiring checks okay then replace the thermistor / optical water indicator component. 

CODE: 3-3 
PROBLEM: Optical Water Indicator (OWI) has failed 
FIX: Remove power to the dishwasher and clean the optical water indicator. If the error code comes back once you apply power then replace the optical water indicator (OWI). 

CODE: 4-3 
PROBLEM: Communication stopped from the wash pump motor and the electronic control board 
FIX: Remove power to the dishwasher and check the wiring from the wash pump motor to the electronic control board. If the wiring checks to be okay then replace the wash pump. If the problem comes back then replace the electronic control board. 

CODE: 5-1 
PROBLEM: Dishwasher door will not shut (Door Latch Issue) 
FIX: Press start button and close the dishwasher door. If the code shows then remove power to the dishwasher. Check the door latch assembly and the wiring for the door switch. If the latch assembly and the wiring are in place and check good then replace the door switch. 

CODE: 5-2 
PROBLEM: Dishwasher door will not open 
FIX: Check to be sure the wiring in the door switch checks good. If the door switch wiring checks good then replace the door switch. 

CODE: 6-1 
PROBLEM: Electronic control board does not detect water coming into the tub 
FIX: Remove power and turn off the water supply to the dishwasher. Be sure the water supplying the dishwasher has proper flow and good pressure. Check wiring to the water inlet valve. If the wiring checks good and the water supply checks out then replace the water inlet valve. 

CODE: 6-2 
PROBLEM: The water inlet valve is having an electrical issue 
FIX: Remove power and turn off the water supply to the dishwasher. Be sure the water supplying the dishwasher has proper flow and good pressure. Check wiring to the water inlet valve. If the wiring checks good and the water supply checks out then replace the water inlet valve. If the problem persists then replace the electronic control board. 

CODE: 6-3 
PROBLEM: Air or SUDS are in the water pump 
FIX: Check the water fill level. Check for suds in the fill water at the bottom of the dishwasher tub. If the water fill level is low then replace the water inlet valve. If you find excess suds then check the detergent dispenser and replace it if damaged. 

CODE: 6-4 
PROBLEM: The float switch is electrically open or stuck 
FIX: Check the overfill float switch and make sure it is not stuck under there is something under it holding it up. Be sure the water inlet fill valve is shutting off the water when the dishwasher is turned off. 

CODE: 6-6 
PROBLEM: Water coming into dishwasher is too cold 
FIX: Use thermometer to check the water temperature coming into the dishwasher. If the water is lower than 110F degrees then check your water heater. Adjust water heater if needed. If the water temperature coming into the dishwasher is between 110F to 120F degrees then replace the thermistor / optical water indicator or as last resort the electronic control board. 

CODE: 6-7 
PROBLEM: Flow meter is not connected or faulty 
FIX: Remove power to the dishwasher. Check the wires to the flow meter. If the wiring checks good then replace the flow meter. 

CODE: 7-1 
PROBLEM: Heating element not heating 
FIX: Remove power to the dishwasher. Check the heating element and replace it if you find it to be burned or faulty. If the heating element checks good then check the wires to the heating element. If the wiring checks out then replace the heating element. 

CODE: 7-2 
PROBLEM: Heating element will not turn off – constant heat 
FIX: Remove power to the dishwasher for 10 minutes. If the error code comes back when you turn power back on then replace the electronic control board. 

CODE: 8-1 
PROBLEM: Water is draining too slow 
FIX: Remove power to the dishwasher and turn off the water supply to the dishwasher. Check the drain path to see if something is blocking it. If the drain path is clean and completely clear then check the wires on the drain pump. If the wiring check out then replace the drain pump. 

CODE: 8-2 
PROBLEM: Electrical problem with drain pump 
FIX: Remove power to the dishwasher and turn off the water supply to the dishwasher. Check the wires on the drain pump. If the wiring checks out then replace the drain pump. 

CODE: 8-3 
PROBLEM: Drain pump is stuck ON constantly 
FIX: Remove power to the dishwasher and check the drain pump wires. If there is damage to the the wire harness replace it. If the wiring harness checks out then replace the electronic control board. 

CODE: 10-1 
PROBLEM: Electrical problem with dispenser 
FIX: Remove power to the dishwasher. Remove the outer door panel. Check the wires in the detergent dispenser. If the wiring check out then replace the detergent dispenser. 

CODE: 10-3 
PROBLEM: Drying fan issue 
FIX: Remove power to the dishwasher. Check the wires for the the drying fan. If the wiring checks out then replace the drying fan.


Dryer Error Codes

CODE: F01 — Electronic circuit board fault 
PROBLEM: Tumble Dryers is not operating – some or all functions are not selectable. 
FIX: Disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again. 

CODE: F02 — Motor circuit fault 
PROBLEM: Intermittent or no drum rotation during wash cycle. 

CODE: F03 — Temperature sensing fault 
PROBLEM: Tumble Dryers not heating on wash or dry settings. 

CODE: F05 — Waste pipe blockage or pump issue 
PROBLEM: Tumble Dryers door will not open / the door can be opened but water remains inside the drum. 
FIX: Please check for blockages in your pump filter (if applicable to model – please see user handbook). Also check for any blockages in waste water hose and in any under-sink plumbing. If none of the above solutions work, it is likely you have a pump failure and will need further assistance. 

CODE: F06 — Door lock fault 
PROBLEM: Tumble Dryers door cannot be opened or closed / when the door is closed the machine the programme will not start. 
FIX: If your tumble dryers door will not close, please check for any obstructions in the door lock.  

CODE: F07 — Electronic circuit board fault / heating circuit fault 
PROBLEM: During a wash cycle the programme pauses part way through/ the machine is not heating and the pump runs continuously. 

CODE: F08 — Heater fault 
PROBLEM: During a wash cycle the programme pauses part way through. 

CODE: F09 — Software fault 
PROBLEM: Tumble Dryers isn’t operating multiple flashing lights and/or display. Unable to select a programme. 

CODE: F11 — Pump circuit fault 
PROBLEM: Water remains in Tumble Dryers / not pumping out. 

CODE: F12 — Electronic control fault 
PROBLEM: Tumble Dryers is not operating (turning on). 

CODE: F13 — Dryer temperature sensing fault (washer dryers only) 
PROBLEM: Washer dryer is not drying clothes. 

CODE: F15 — Heater control fault (Washing Machine and Washer Dryers) 
PROBLEM: Tumble Dryers is not heating water or pauses during a wash cycle / not drying or pauses during drying cycle. 

CODE: F16 — Drum lock position sensor fault (top loading machines only) 
PROBLEM: Tumble Dryers drum is stopping in the wrong position or is not locked in the correct position. 

CODE: F18 — Internal data error 
PROBLEM: Some or all display / functions do not work on my tumble dryers. 
FIX: Please disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply, wait 30 seconds and try starting the machine again. 

CODE: F19 — Fan motor or heating fault (washer dryers only) 
PROBLEM: Tumble Dryers is not drying / stops during drying cycle.


Furnace Error Codes

CODE: O P. 
PROBLEM: Normal operation. 

CODE: E 0. 
PROBLEM: Lockout due to excessive retries. 

CODE: E 1. 
PROBLEM: Low-stage pressure switch stuck closed at start of heating cycle. 

CODE: E 2. 
PROBLEM: Low-stage pressure switch stuck open. 

CODE: E 3. 
PROBLEM: Open high-limit switch. 

CODE: E 4. 
PROBLEM: Flame detected when no flame should be present. 

CODE: E 5. 
PROBLEM: Open fuse. 

CODE: E 6. 
PROBLEM: Low flame signal. 

CODE: E 7. 
PROBLEM: Igniter fault or improper grounding. 

CODE: E 8. 
PROBLEM: High-stage pressure switch stuck closed at start of heating cycle. 

CODE: E 9. 
PROBLEM: High-stage pressure switch stuck open. 

CODE: E A. 
PROBLEM: Reversed 115 VAC polarity. 

CODE: d 0. 
PROBLEM: Data not yet on network. 

CODE: d 4. 
PROBLEM: Invalid memory card data. 

CODE: b 0. 
PROBLEM: Blower motor not running. 

CODE: b 1. 
PROBLEM: Blower communication error. 

CODE: b 2. 
PROBLEM: Blower HP mismatch. 

CODE: b 3. 
PROBLEM: Blower motor operating in power, temperature or speed limit. 

CODE: b 4. 
PROBLEM: Blower motor current trip or lost rotor. 

CODE: b 5. 
PROBLEM: Blower motor locked rotor. 

CODE: b 6. 
PROBLEM: Over/under voltage trip or over temperature trip. 

CODE: b 7. 
PROBLEM: Incomplete parameters sent to motor. 

CODE: b 9. 
PROBLEM: Low indoor airflow. 

CODE: C 1. 
PROBLEM: Low-stage cooling. 

CODE: C 2. 
PROBLEM: High-stage cooling. 

CODE: L O. 
PROBLEM: Low-stage heat. 

CODE: H I. 
PROBLEM: High-stage heat. 

CODE: F. 
PROBLEM: Continuous fan. 

CODE: 1 2. 
PROBLEM: CFM/100; Alternates with C1, C2, LO, HI, F.


Microwave Error Codes

CODE: ":" or "." 
PROBLEM: There has been a power failure, or the clock time has been turned off.  
FIX: 
Power unit down by turning off the circuit breaker(s) for one (1) minute. 
Power unit up by turning on the circuit breaker(s). 
Monitor the oven for one (1) minute to ensure the error code does not display again. 
Verify oven operation. 

CODE: DOOR or OPEN and CLOSE DOOR 
PROBLEM: If a message about the door appears in the display, the door has been closed for 5 minutes or more without the microwave oven being started. 
FIX: 
Remove all packing material from the Microwave.    
Be sure no packing material is blocking the door lock system. 
Close the door firmly. 
Check that the cooking rack (if equipped) is not out of position and not allowing the door to close. 

CODE: Err7  
PROBLEM: There may be a problem with the User Interface or Keypad, the Control, or the associated wiring. 
FIX: 
Power unit down by turning off the circuit breaker(s) for one (1) minute. 
Power unit up by turning on the circuit breaker(s). 
Monitor the oven for one (1) minute to ensure the error code does not display again. 
Verify oven operation. 

CODE: ERROR during sensor cooking 
PROBLEM: The sensor is not detecting humidity. 
FIX: 
Power unit down by turning off the circuit breaker(s) for one (1) minute. 
Power unit up by turning on the circuit breaker(s). 
Monitor the oven for one (1) minute to ensure the error code does not display again. 
Verify oven operation. 

CODE: Feature Not Available or Fault Detected 
PROBLEM: This message will scroll across the display when a fault is detected while you are programming a cook cycle. 
FIX: 
Power unit down by turning off the circuit breaker(s) for one (1) minute. 
Power unit up by turning on the circuit breaker(s). 
Start a bake cycle. 
Monitor the oven for one (1) minute to ensure the error code does not display again. 
Verify oven operation. 

CODE: Flashing Time, Clock, 12:00, Power Loss or Enter Time 
PROBLEM: When power is first supplied to the oven, after a power interruption or failure, the "Time", or “12:00”, or “POWER LOSS” will be displayed.  
FIX: 
Press CANCEL to clear the display. 
Set time of day. 

CODE: Locked, Lock or Loc 
PROBLEM: The Control Lock shuts down the panel controls to avoid unintended use of the microwave oven. When the control panel is locked, none of the controls will function. 
FIX: 
Power unit down by turning off the circuit breaker(s) for one (1) minute. 
Power unit up by turning on the circuit breaker(s). 
Monitor the oven for one (1) minute to ensure the error code does not display again. 
Verify oven operation 

CODE: No Beeps or Tones 
PROBLEM: Is the tone function turned off? 
FIX: 
If the range is in Energy Save mode (select models), the display will be blank when not in use. The Energy Save mode puts the product into sleep mode and reduces energy consumption. 
To Deactivate the Energy Save Mode: 
1.  Press and hold SETTINGS/CLOCK for 3 seconds.  "Energy saver off" will appear in the display. 
2.  The clock will reappear in the display and the range can be operated as usual. 
To Activate the Energy Save Mode: 
1.  Press and hold SETTINGS/CLOCK for 3 seconds.  "Energy saver on" will appear in the display.   
2.  The setting will be activated after 5 minutes. 

CODE: Press Cancel to Reset 
PROBLEM: This message will be displayed when a fault or error has been detected. 
FIX: 
Power unit down by turning off the circuit breaker(s) for one (1) minute. 
Power unit up by turning on the circuit breaker(s). 
Start a bake cycle. 
Monitor the oven for one (1) minute to ensure the error code does not display again. 
Verify oven operation. 

CODE: Probe or Insert Probe 
PROBLEM: The Control is "looking" for an input from the Meat Probe. 
FIX: 
Power unit down by turning off the circuit breaker(s) for one (1) minute. 
Power unit up by turning on the circuit breaker(s). 
Monitor the oven for one (1) minute to ensure the error code does not display again. 
Verify oven operation.


Range Error Codes

CODE: F0 
PROBLEM: Default F code-no failure 
FIX: The F0 code displays if there are no previous fault codes and you hold the CANCEL key for 5 seconds. Press CANCEL to clear the display. 

CODE: F1 
PROBLEM: Defective electronic oven control (EOC) 
FIX: Disconnect power or unplug the range. Replace the electronic oven control (EOC). 

CODE: F2/E0 
PROBLEM: Keypad wire harness is disconnected 
FIX: Disconnect power or unplug the range. Reconnect the keypad wire harness if loose. Restore electrical power to the range and press CANCEL. If the error code returns after 60 seconds, replace the keypad. If the problem persists, replace the electronic oven control. 

CODE: F2/E5 or F2/E6 
PROBLEM: Cancel key is defective 
FIX: Disconnect power or unplug the range. Reconnect the keypad wire harness if loose. Restore electrical power to the range and press CANCEL. If the error code returns after 60 seconds, replace the keypad. If the problem persists, replace the electronic oven control. 

CODE: F3/E0 
PROBLEM: Defective oven temperature sensor or open oven temperature sensor circuit 
FIX: Disconnect power or unplug the range. Reconnect the oven temperature sensor wire harness connection if loose. Replace the wire harness if damaged. Measure the oven temperature sensor resistance using a volt/ohm meter. If the resistance isn't 1080 ohms at room temperature (70 degrees F), replace the oven temperature sensor. If the oven temperature sensor resistance and wire harness connections are okay, replace the electronic oven control (EOC). 

CODE: F3/E1 
PROBLEM: Defective oven temperature sensor or shorted oven temperature circuit 
FIX: Disconnect power or unplug the range. Reconnect the oven temperature sensor wire harness if loose. Replace the wire harness if damaged. Measure the oven temperature sensor resistance using a volt/ohm meter. If the resistance isn't 1080 ohms at room temperature (70 degrees F), replace the oven temperature sensor. If the oven temperature sensor resistance and wire harness connections are okay, replace the electronic oven control (EOC). 

CODE: F3/E2 
PROBLEM: Oven temperature is over 575 degrees F in Bake mode. 
FIX: Disconnect power or unplug the range. Reconnect the oven temperature sensor wire if loose. Replace the wire harness if damaged. Measure the oven temperature sensor resistance using a volt/ohm meter. If the resistance isn't 1080 ohms at room temperature (70 degrees F), replace the oven temperature sensor. If the oven temperature sensor resistance and wire harness connections are okay, replace the electronic oven control (EOC). 

CODE: F3/E3 
PROBLEM: Oven temperature is over 950 degrees F in Clean mode 
FIX: Disconnect power or unplug the range. Reconnect the oven temperature sensor wire if loose. Replace the wire harness if damaged. Measure the oven temperature sensor resistance using a volt/ohm meter. If the resistance isn't 1080 ohms at room temperature (70 degrees F), replace the oven temperature sensor. If the oven temperature sensor resistance and wire harness connections are okay, replace the electronic oven control (EOC). 

CODE: F4/E1 
PROBLEM: Meat probe shorted 
FIX: Disconnect power or unplug the range. Unplug the meat probe and measure the resistance of the meat probe using a volt/ohm meter. If the resistance isn't 59,000 ohms at room temperature, replace the meat probe. If the resistance of the meat probe is okay, insert the meat probe in the jack and check for a firm connection between the probe and jack in the oven. If the jack is damaged or worn out, replace it. Reconnect the wire harness connection on the meat probe jack if loose. Replace the wire harness if damaged. 

CODE: F5/E0 
PROBLEM: Door is open, but latch is locked (door switch communicates an open door, but latch switch communicates a locked door) 
FIX: Test the oven door switch operation using the oven light. Open and close the oven door to see if the oven door switch turns the oven light on and off when the oven door is opened and closed. If the oven door switch is defective, replace it. Disconnect power or unplug the oven. Reconnect any loose wires on the oven door lock assembly wire harness. Replace the wire harness if damaged. Check the door lock assembly for visible damage and replace it if broken. 

CODE: F5/E1 
PROBLEM: Self-clean latch won't lock/unlock 
FIX: Disconnect power or unplug the range. Reconnect any loose wires on the oven door lock assembly wire harness. Replace the wire harness if damaged. Check the door lock assembly for visible damage and replace it if broken.


Refrigerator Error Codes

E0 - Ice maker fault (if fitted) 
Issue: The ice maker in my appliance is not working correctly. 

E1 - Refrigerator sensor fault 
Replace sensor 

E2 - Freezer sensor fault 
Issue: The compartment temperature in my freezer is incorrect. 

E3 - Defrost sensor fault 
Issue: The compartment temperature in my fridge is incorrect. 
Advice: We recommend you check that the drain pipe and under sink plumbing for any blockages. 

E4 - Fridge defrost sensor fault 
Issue: The compartment temperature in my fridge is incorrect. 

E5 - Freezer defrost sensor fault. 
Issue: The compartment temperature in my freezer is incorrect. 

E6 - Main control-board and display board fault. 
Issue: The display or controls on my appliance are not operating correctly. 

E7 - Environmental temperature sensor fault. 
Issue: A number of things affecting the temperature in your appliance could be happening if you see this error code displayed. 

E8 - Environmental temperature sensor fault 
Issue: A number of things affecting the temperature in your appliance could be happening if you see this error code displayed. 

E9 - Freezer high temperature alarm 
Issue: The freezer door may have been left open which has resulted in the food in freezer defrosting. 
Advice: Please check to see if your door is closed properly. 

EE - Ice maker circuit fault (if fitted). 
Issue: The ice maker in my appliance is not working correctly.


Washer Error Codes

CODE: LOC or LC 
PROBLEM: Control Lock has been activated  
FIX: Touch the Control Lock button, or (on older models) determine which button activates control lock from your Owner's Manual. Some models require you to press and hold the button. 

CODE: dET  
PROBLEM: Detergent cartridge not detected in the dispenser.  
FIX: This is on select models. If you are using single-load doses of detergent, ignore this message. Ensure the dispenser cartridge is inserted correctly and the dispenser drawer is shut completely. 

CODE: Int  
PROBLEM: The cycle was paused or canceled.  
FIX: The washer may take 20 to 30 minutes to stop spinning and drain, and will display this error code during that time. To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. 

CODE: rL or F34  
PROBLEM: Items were detected in the washer during the Clean Washer cycle.  
FIX: Remove items from the drum and restart the Clean Washer cycle. 

CODE: Sud or Sd  
PROBLEM: There are too many suds in the washing machine.  
FIX: The washer will not be able to spin out water with the excess suds. When "Sud" or "Sd" is displayed, the washer automatically extends the rinse time to remove the excess suds. During this time, the washer pauses the tumbling and adds water for additional rinsing. This pause allows the bubbles in the suds to break. This pause and rinsing are necessary and may occur several times to eliminate the suds. 

CODE: F5 E2  
PROBLEM: The door is not locking properly.  
FIX: Check that there are no items blocking the door and it is closing completely. Press the Pause or Cancel button twice and the Power button once to clear the code. 

CODE: F7 E1  
PROBLEM: Indicates a motor speed sensing error,  
FIX: The motor can not achieve the correct speed for the cycle selection. Check that All the shipping bolts have been removed, the washer has not been overloaded, press the Pause or Cancel button twice and the Power button once to clear the code. 

CODE: F8 E1 or LO FL  
PROBLEM: The washer is sensing a low flow of water.  
FIX: Check that, the household water supply is turned on and both the cold and the hot water faucets or valves are fully open. The water inlet hoses are not kinked (learn more about How to check your Fill Hoses if your Washer is not Filling). There are no anti-flood hoses and controls in the water line connected to the washer (learn more about Should I use Flood Safe Devices on my Front Load Washer. Press the Pause or Cancel button twice and the Power button once to clear the code. 

CODE: F8 E2  
PROBLEM: Indicates there is a problem with the Dispenser System  
FIX: This is on select models. Verify detergent drawer or detergent cartridge is not clogged with detergent.  

CODE: F9 E1  
PROBLEM: Indicates that drain times are longer than expected, typically over eight (8) minutes.  
FIX: Make sure the drain hose is not kinked or clogged. Use the U-shaped drain hose form on the drain hose. The standpipe (drainpipe) height requirements are 96" (244 cm) maximum and 39" (99 cm) minimum. 

CODE: Other F# E# code  
PROBLEM: Indicates other error  
FIX: Unplug the washer or disconnect the power for one minute and reconnect it again. Reselect the cycle and press Start. 


Water Heater Error Codes

CODE: E01 
PROBLEM: Electrical power on with the tank empty or not completely full of water 
FIX: Turn off electrical power at breaker. Open a hot water faucet in the house and then turn the cold water supply on to the water heater and allow time for the tank to fill with water. Once you see water coming out of the hot water faucet, turn the hot water faucet off. Restore power and then allow the water heater to run a system diagnostic. This typically takes 8 minutes. 

CODE: E02 
PROBLEM: Water temperature exceeded high limit 
FIX: Switch the two house circuit breakers dedicated for the water heater to OFF and then press the reset button located behind the control panel on the water heater. Flip the house circuit breakers to the ON position. If error returns, call a service technician for assistance. 

CODE: E03 
PROBLEM: Upper thermistor sensor failure 
FIX: Switch the two house circuit breakers dedicated for the water heater to OFF. Replace the electronic thermostat located behind the control panel. 

CODE: E04 
PROBLEM: Upper element failure 
FIX: Switch the two house circuit breakers dedicated for the water heater to OFF. Remove the control panel to access the upper heating element. Disconnect the upper heating element and measure across the element terminals for ohm resistance. Using a multi-meter, check the wires at the element and electronic thermostat for damage. The heating element should measure 5-25 ohms of resistance. Drain the water heater and then replace the heating element if it's defective. If this error condition continues, replace the electronic thermostat. Refill the water heater before you flip the house circuit breakers ON and restoring power. 

CODE: E05 
PROBLEM: Lower element failure 
FIX: Switch the two house circuit breakers dedicated for the water heater to OFF. Remove the lower cover to access the lower heating element. Disconnect the lower heating element and measure across the element terminals for ohm resistance. Drain the water heater and then replace the heating element if it failed. If this error condition continues, replace the electronic thermostat. Refill the water heater before you flip the house circuit breakers ON and restore power. 

CODE: E06 
PROBLEM: Electronic thermostat failure 
FIX: Switch the two house circuit breakers dedicated for the water heater to OFF. Next, flip the breakers to ON to see if error clears. If the error does not clear, switch the circuit breakers OFF and replace the electronic thermostat located behind the control panel. 

CODE: E07 
PROBLEM: Lower thermistor sensor failure 
FIX: Switch the two house circuit breakers dedicated for the water heater to OFF. Remove the control panel and check the electrical connections on the electronic thermostat. If the wiring and connections are okay, replace the lower thermistor sensor located above the lower heating element. 

CODE: E08 
PROBLEM: Energy smart module failure (ESM) 
FIX: Switch the two house circuit breakers dedicated for the water heater to OFF. Check the wires and the energy smart module (control panel) for damage. If this error condition continues, replace the energy smart module (ESM). You can override the ESM by unplugging the harness connector. The water heater electronic thermostat will continue to operate and hot water will still be available. Replace the ESM. 

CODE: E9, E10, E11, E12 
PROBLEM: Electronic thermostat (ET) error 
FIX: Switch the two house circuit breakers dedicated for the water heater to OFF. Check the wiring at electronic thermostat for damage. Restore electrical power at the breaker. If this error code continues to flash, replace the electronic thermostat.



Whirlpool Appliance Error Codes

Whirlpool appliance fault codes

Whirlpool appliance diagnostic codes

Whirlpool appliance error symbols

Whirlpool appliance common faults


Product Reviews:

Whirlpool gold model GI6FDRXXQ06 - This fridge is 3 years old and we are ab
Whirlpool gold model GI6FDRXXQ06 - This fridge is 3 years old and we are about to put the fifth ice maker in it. Vegetables freeze in the vegetable drawer (yes, its set correctly). Our repairman even says the design is faulty but since the warranty is out, we have to keep replacing the units!
Published: March 3, 2015
dan of Calhoun, LA
Source: consumeraffairs.com

I have tried to contact Whirlpool, email and telephone call. Finally someon
I have tried to contact Whirlpool, email and telephone call. Finally someone called me but Customer Service was poor. I asked her to have a Manager call me, but she never did. They also never responded to my email. We Purchased our new Refrigerator 21 c.f. side by side 2 months ago. The ice maker is driving us crazy. It is very loud. There are white plugs on the 2 bottom corners that make the appliance look extremely cheap. I am not happy with this Refrigerator!
Published: February 16, 2021
Diana of Marietta, GA
Source: consumeraffairs.com

I dont think I ever bought another product where one of its highlighted fea
I dont think I ever bought another product where one of its highlighted feature does absolutely nothing. Using the Aqua Lift cleaning process is a waste of time and electricity. We were told this range had a self-cleaning oven when we bought it. If a self-cleaning oven is important to you buy something else.
Published: August 25, 2016
denis of Chandler, AZ
Source: consumeraffairs.com

My whirlpool refrigerator relay switch caught on fire and customer service
My whirlpool refrigerator relay switch caught on fire and customer service told me that my model wasnt on their list of problems refrigerators, but they know there are a lot of units out with the chance that it could start a fire if anyone has a whirlpool product refrigerator. I would call 1-888-923-8502 and check to see if it is on there list to replace the switch.
Published: October 25, 2011
Greg of Louisville, KY
Source: consumeraffairs.com

I recently purchased a Whirlpool Slide in Oven replacing my Amana stove of
I recently purchased a Whirlpool Slide in Oven replacing my Amana stove of 15 years. My Amana was a very basic model, and I thought this WP was an upgrade. But it is so poorly made its ridiculous. First of all the bottom storage drawer, is so flimsy, it does not slide out easily, and the top lip doesnt even have a finished edge. Additionally there is a 1 inch gap between the top of the drawer and the bottom of the stove door. But the BIGGEST disappointment was the oven racks, totally flimsy.We used a Lodge Dutch Oven (which we have used many times with our old stove) and the oven rack sagged under the weight. Had I known I would have pulled the racks from my old stove. I contacted that seller about these issues, and they said they are ALL like that even the higher end ones, and I contacted Whirlpool to see if I could buy better quality racks and they said no, this is all they have.
Published: October 17, 2019
Rebekah of Gurnee, IL
Source: consumeraffairs.com

Whirlpool oven aqua lift - This oven is the worst in the world. I cant even
Whirlpool oven aqua lift - This oven is the worst in the world. I cant even imagine cooking a turkey in it. After cooking a pizza it took four cleanings and a lot of scrubbing. Self cleaning --- not, you clean and clean and clean. I have had ovens that were not self cleaning and easier to clean than this. Do not buy. And Lowes is no help at all. Run as fast as you can.
Published: November 11, 2015
lucy of Addison, IL
Source: consumeraffairs.com

I bought a Whirlpool High Efficiency top load washer. It does not get the c
I bought a Whirlpool High Efficiency top load washer. It does not get the clothes clean. Dark clothes come out with spots all over them. There is not enough water to rinse out the dirt. It is left on the clothes in spots. I have to take my clothes to the laundry mat to wash them to get them clean. I am 74 years old and have used Whirlpool appliances all my life. I have dt3 rental houses I keep Whirlpool appliances in. But I wont be buying any more. I had to call the repair man one month after I bought it. He had to recalibrate the machine. If all you want to wash or maybe rinse out is a pair of slacks or a shirt, it might be o.k. but not a load of dirty clothes. It is just a JOKE.
Published: December 30, 2013
Elva of Anton, CO
Source: consumeraffairs.com

I have replaced the damper control unit three times the last three years. T
I have replaced the damper control unit three times the last three years. The part begins to fail after nine months in used. The temperature becomes too cold in the refrigerator and the food started frozen because the damper door wont closed as cold air flows from freezer to the refrigerator. It adds to the displeasure that Whirlpool is not taking care of the shipping cost even the part is under warranty.
Published: January 28, 2018
Homer of Vernon Hills, Illinois
Source: consumeraffairs.com

Whirlpool oven WOD93ECOA501 - This oven will most likely lock up if you use
Whirlpool oven WOD93ECOA501 - This oven will most likely lock up if you use the clean cycle. I wish there was a class action suit in California. This happened first time I used the oven. Very expensive to fix, and though it was 9 months after a kitchen remodel, it was not under warranty because we bought it early and it sat in garage, and Whirlpool could only use purchase date. This is not new technology. Upper and lower oven both locked. Wish I had bought a Blue Star oven, as my Blue Star cook top is fantastic and a pleasure to use. HAS ANYONE GONE TO SMALL CLAIMS COURT?
Published: February 12, 2015
Germaine of Santa Ana, CA
Source: consumeraffairs.com

We bought a Whirlpool washing machine two years ago and bought the extended
We bought a Whirlpool washing machine two years ago and bought the extended warranty. The machine quit working so we called the warranty service number. We have had a repair man sent here 5 times from them. The technicians have put two new control boards and a new door lock on it. They have another part ordered for this week.The machine is still not working after five visits from service technicians and they say they cant fix it. The extended warranty service plan says if it cant be fixed they will replace it or send us a check for it. We have contacted them several times and they dont want to make good on it. So we have a broke down washing machine and have to go to a Laundromat every week.
Published: October 9, 2011
Vernon of LaGrande, OR
Source: consumeraffairs.com

DO NOT BUY THIS MACHINE. Mine is less than 2 years old. First one month aft
DO NOT BUY THIS MACHINE. Mine is less than 2 years old. First one month after warranty expired, the clear lid cracked...$350 to replace! Then a few days ago a rusted circuit board came apart and jammed up my washer. This should NEVER happen. I contacted customer service and they told me that they are not covering this problem and that the service call is $175 and cannot estimate the repair cost. They also could not send a repair person out for 5 days. The washer has not been repaired yet so I do not know the entire cost but it will be expensive!
Published: August 14, 2013
Yvonne of Huntington Beach, CA
Source: consumeraffairs.com

Update Review on 10/15/2020: New refrigerator 12/31/19. 4/27/20 Fridge terr
Update Review on 10/15/2020: New refrigerator 12/31/19. 4/27/20 Fridge terribly noisy, called Whirlpool directed to local provider. 5/5/20 Fan replaced, drawer clip broken. 5/11/20 Drawer repaired. 5/21/20 Fridge not keeping up, repair company said new compressor needed. 7/6/20 After numerous calls and literally hours on hold with Whirlpool compressor install but still seemed noisy. 9/30/20 Fridge partially cooling, no ice and water dispenser not working. Repair company ordered new evaporator cover and UI panel.10/15/20 Neither the repair company or Whirlpool know when the parts will be delivered. Whirlpool has no record of their being a service call or parts ordered. I talked to one rude, unhelpful and uninformed service rep. After following their instructions and using their recommended warranty provider, they claim not to have the issues in their system and cant be used to determine the repair/replacement of their unit. He indicated, You need 3 major repairs in 30 days to get a replacement fridge. It took them 6 1/2 weeks to repair the compressor. How can it break that many times in 30 days with that bad of service. Nothing is repaired in 30 days. The current rep seems to care and have a working knowledge. She is sending a request to determine when a part might be delivered. She couldnt give any indication of when the part might be delivered to complete the repair. Days? Weeks? Or again Months? An hour and a half on the phone with very little progress. New refrigerator with 3 major repairs and one small one in 9 months. Terrible refrigerator and extremely poor service! Go with another brand.Original Review: Refrigerator new in January 2020. The first issue was an extremely loud fan.It was replaced. While being repaired, service tech broke a tab on the door. (It happens) Another call to replace the tab. During May I notice its not making ice and freezer isnt keeping up. Lose all items in freezer. Now the 4th call on new refrigerator, tech says needs a compressor and orders while at my house. Soon the refrigerator isnt keeping cool. Now 34 days later, still not fixed. Whirlpool service provider blames Whirlpool. Whirlpool says they are shipping compressors but cant exactly say mine is delivered. Apparently, 4 service calls in 5 months and over a month with a totally broken refrigerator is their bar for a good product and service. Neither their approved service provider or Whirlpool care in the least. Awful service. Try another brand!
Published: June 24, 2020
Doug of Erie, CO
Source: consumeraffairs.com

Bought Whirlpool electric range in Dec. 2005..expensive..so the warranty
Bought Whirlpool electric range in Dec. 2005..expensive..so the warranty expired a few months ago. The electronic keypad that controls the oven and lights doesnt work. The repairs will be $408 plus tax which is obscene, and are guaranteed only for 90 days.This after only 5 years of minimal use...just me using it.I will never buy whirlpool again.
Published: August 1, 2011
Val of Murrells Inlet, SC
Source: consumeraffairs.com

My not yet 3yr old ($2100.00) Whirlpool refrigerator started having problem
My not yet 3yr old ($2100.00) Whirlpool refrigerator started having problems. I thought it was related to the ice maker. When the repairman came out, he said it had leaked the Freon, so I thought it should have been a simple fix. Boy was I wrong. It turns out it has a sealed system so no one can access this to fix it. It is now junk and I have to buy a new one. I will never purchase Whirlpool anything ever again and I will also tell anyone who will listen about my experience. My repairman said this happens all the time, and 7 or 8 yrs ago Whirlpool went from being one of the top models to being junk.
Published: May 26, 2015
Renee of Flushing, MI
Source: consumeraffairs.com

August 15, 2011 - We purchased a new Whirlpool Water Heater Model N50T61-40
August 15, 2011 - We purchased a new Whirlpool Water Heater Model N50T61-403 for $398 from Lowes. We used their recommended installer (that was our first mistake!). He made the following installation mistakes: 1. He connected the hot water to the cold water & the cold water to the hot water. 2. He installed DRYER venting instead of HVAC venting. 3. He used flammable tape on the venting instead of screws. 4. He had incompatible metals touching near the gas line which can create an electrical charge & thus, a sparking situation. 5. He left us with a gas leak. 6. He did not install the screen that is supposed to surround the base of the water heater.7. He failed to strap down the expansion tank.These failures were discovered by an HVAC person who was in our basement to give an estimate on a replacement of the furnace & AC coil at the same time this genius was installing our water heater. The installer overheard the comments & literally... he disappeared & we never saw him again! We told all of this to Lowes & they were not phased in the least -- indeed, they didnt even seem surprised! They sent out a few other guys from the same company to correct the errors. So, it finally was installed & passed the county inspection & we had hot water again... for a little while. Within a few months the water heater pilot light would not stay lit. I was having to relight it once a week or so. After much arm twisting, we were finally able to get Whirlpool to send out a new pilot light assembly and pay for the installation. It was installed July 25, 2012. And.... it worked for 8 months. After returning from a trip on April 30, 2013, we went to take showers & the water was cold. The same problem was happening again... The pilot light had gone out while we were out of town & it will not stay lit & I have to relight it every 2-3 days.We talked to an assistant manager at the Lowes store where it was purchased. He talked to Whirlpool & Whirlpool said they would pay for the parts but not the service call which would be $149. I also learned today from the same manager that Whirlpool will not replace the product until they have replaced the same parts three times. Hmmmm.... Lets do some basic math here. $149 x 3 = $447! Thats MORE than the water heater cost! We believe that the water heater has been defective from day one & we also contend that their replacement part for the pilot light assembly is also defective (by design??). A pilot light assembly should last longer than 8 months!We are getting ready to build a new home within the next year. We will get to choose our supplier & the manufacturer of the appliances that will be in our home. Needless to say, Lowes will not be on the list. They keep saying, Our hands are tied. (Not buying it!) And Whirlpool will definitely be off of our list as their customer service is the worst Ive ever seen & their product quality is sub par. The other thing I experienced with Lowes was that when I tried to leave a review on their site for this specific product... twice... both reviews were rejected. The reviews presented the facts as Ive stated here, but because they showed Lowes & Whirlpool in a negative light, they were not posted on lowes.com. So, consumer beware -- their reviews are heavily screened so that the negative reviews rarely get posted. The consumer should be aware that the reviews on Lowes website are heavily screened & therefore do not equally represent consumers who have had a negative experience. This is an integrity issue.
Published: July 27, 2013
Wendy of Highlands Ranch, CO
Source: consumeraffairs.com

My $700 Whirlpool Cabrio washing machine just broke after only 16 months of
My $700 Whirlpool Cabrio washing machine just broke after only 16 months of having it. The error code that comes up is f 51. With some research, I found that these machines are notorious for breaking down just after warranty with an f 1 code for older machines and an f 51 code for newer machines. Whirlpool is well aware of the breakdowns and the defect inherent in these machines and still sells them with no warning or no recall to fix the problem. I contacted the company and they refused to fix it for free and I understand the fix will now cost me another $300 to $400! What a scam! I will never buy Whirlpool or any of their other products again!
Published: July 20, 2012
Richard of Raleigh, NC
Source: consumeraffairs.com

My wife and I went and bought a new Whirlpool 27 cubic foot French door fri
My wife and I went and bought a new Whirlpool 27 cubic foot French door fridge model WRF767SDEMO1 in 3-13-17 from Lowes and I have all the paperwork. And on Monday the May-28-2018 it stopped making ice, so I called a repairman and he came out May-31-2018 and he said it was leaking gas and it cannot be FIXED and it is JUNK. He told me to, Call Whirlpool and tell them you want a new one. I called Whirlpool and they are sending one of their repairmen out June -5- 2018 to check it and by that time I will lose everything in the fridge because it stopped working.
Published: May 31, 2018
Bill of Memphis, TN
Source: consumeraffairs.com

Re: wdf7payw6. I purchased this unit last February. It has never washed pro
Re: wdf7payw6. I purchased this unit last February. It has never washed properly. In the last month 2 separate warranty service reps have been out. The first one told me that I have not been doing a good enough job of prewashing the dishes so the arms were clogged. While cleaning them, he broke the top arm. When he came back to replace the top arm, he added that the dishes were not drying because I didnt use enough jet dry so I would have to dry by hand, and that the arms were clogging because I didnt prewash well enough. I told him to leave and never come back. I called customer service and they sent out a new company.The rep today told me that even on time delay or overnight settings I must run the hot water prior to starting the unit. And that since the water wasnt hot enough; the undissolved detergent was clogging the spray arms. This was confirmed by your phone support person who told me that for best results thats what I had to do. The result I want is for the thing to wash dishes. It doesnt do that. The current rep ordered a heater, motor pump and spray arms. My previous dishwasher operated perfectly (until the pump failed) for the 18 years I have lived in this house plus however long it was here before I moved in. I will never buy a Whirlpool product or anything built by subsidiaries or parent AGAIN.
Published: December 10, 2014
michael of Libertyvile, IL
Source: consumeraffairs.com

Such an expensive refrigerator but poor quality. Bought at Home Depot back
Such an expensive refrigerator but poor quality. Bought at Home Depot back in November of 2019. The bottom Freezer freezes up messing up everything only three months after purchase. I wouldn’t recommend it at all to anyone.
Published: February 11, 2020
B of West Palm Beach, FL
Source: consumeraffairs.com

Broke within a year, company wouldnt back its product. Went out for another
Broke within a year, company wouldnt back its product. Went out for another range, chose a different brand. Make sure you know the companys policy in case of breakdown. Sometimes, even though it might be an off brand, might turn out to be the option. Think outside your norm, listen to employee, other consumers. Just because its on sale doesnt mean it actually does its job.
Published: March 16, 2016
Joan of Carolina Shores, NC
Source: consumeraffairs.com

I cant believe the list of people here with poor quality of their washing M
I cant believe the list of people here with poor quality of their washing Machine. My first problem was covered under warranty. I have paid for two service visits from A&E and now every 5 minutes get the LF error. My fabric softener does not drain into load either. My only option is repair again and I got a sorry from Whirlpool. I think Im going to look for an old fashion cheap machine as it cant be of worse quality than this Cabrio wtw6400sw1.
Published: December 1, 2011
Darlene of Fenton, MO
Source: consumeraffairs.com

I bought a refrigerator from Lowe’s and the refrigerator had a lot of man
I bought a refrigerator from Lowe’s and the refrigerator had a lot of manufacturing defects. I called Whirlpool and 3 techs were sent to my house. After the last tech, Whirlpool decided to exchange the refrigerator. Since then, Whirlpool has been playing games with me.
Published: January 30, 2013
Martin of 0, tx
Source: consumeraffairs.com

The washer was 5 months old and broke. Three service appointments and multi
The washer was 5 months old and broke. Three service appointments and multiple phone calls, it still wasn’t fixed. Whirlpool sent rusty parts out to my home and that was the second excuse for not fixing the washer. The poor service guy must have been 70 years old. Hello, how do washer parts get rusty when they are not even used and are kept in a box?
Published: May 4, 2012
Jeanne of Hamilton, NJ
Source: consumeraffairs.com

I feel Whirlpool has a terrific portable dishwasher. I really like the way
I feel Whirlpool has a terrific portable dishwasher. I really like the way it is set up and it is a very nice looking unit. They could improve on their customer service towards their customers. My dishwasher got a crack in it at the top of the door where you open it and they would not send anyone out to fix it for me. I paid a pretty penny for this dishwasher and felt they should have fixed it for me. This happened in the 1 year warranty period. Otherwise I am very happy with it. I had previously had another one that lasted me 14 years.
Published: January 29, 2018
Louise of Costa Mesa, Calif
Source: consumeraffairs.com

A-10 error on display ultimately means needs a new pump. The washer (model
A-10 error on display ultimately means needs a new pump. The washer (model WFC7500VW 2) is 3 months, 9 days old and is now unusable. I cannot get any service (under 1-year manufacturers warranty) because the sticker inside the door with the model and serial # is missing (i.e., it was sold to me by Homedepot.com without a serial # on the door label, sticker is intact and is brand new and apparently was printed without a serial #).I made multiple calls to Whirlpool in Benton Harbor, Michigan and finally spoke with Courtney (who states she was a supervisor) pretty much said all they will do is to reprint a label from the factory and I should have it in 7-10 business days. They refuse to stand behind their product and authorize timely repair of their product they sold to my without a serial # on the door tag from the factory. I have to wait to schedule factory warranty repair until I get the new label (probably 3 weeks plus without a usable washer). Courtney refused to contact me via email for any of her contact information or to supply verification of conversation or promise of a new factory label. Also, she refused to try to authorize any type of manufacturers warranty to fix the brand new unusable washer!
Published: January 9, 2013
Tim of 29455, SC
Source: consumeraffairs.com

After 1 year and 5 months, my old side by side Whirlpool refrigerator stopp
After 1 year and 5 months, my old side by side Whirlpool refrigerator stopped working. The melted ice caused floor damage and ceiling damage of the floor under.
Published: September 28, 2011
Wei of Potomac, MD
Source: consumeraffairs.com

I bought a Whirlpool fridge 4/23/2013. Thanksgiving it went out. I had a re
I bought a Whirlpool fridge 4/23/2013. Thanksgiving it went out. I had a repair company come look at it to see how much it would be to repair. He said the compressor was out, it has a freon leak, and the electric board has a relay that is acting up. Basically it would cost $600 or more to fix. I only paid $750, mind you. Whirlpool customer service said if we pay to have it fixed then send them the paid receipt. They would then give me a 6 month service plan for future repairs if needed. Please tell me how that helps me now? A voucher for $200 or offer something to help me now. Not a happy customer. Thanks for nothing Whirlpool.
Published: December 11, 2015
Ruth of Saint Cloud, MN
Source: consumeraffairs.com

I purchased this Cabrio top loader washing machine (model #WTW5640XW3) afte
I purchased this Cabrio top loader washing machine (model #WTW5640XW3) after I had a Kenmore front loader for 14 years with not one problem. I bought the Cabrio thinking it was good for the price. Well, let me tell you first of all, I dont like the no agitator. The salesman said it was a big seller. I started doing wash and it was smelling like dirty socks when it was done. I own the machine for two months. I cleaned the machine with Afresh thinking the smell on my clean clothes was from being a new machine. Imagine that I have to use extra fabric softener, vinegar. I dont know what to do. This machine stinks. I am going to try to return it. Wish me luck. I dont think it washes right.
Published: December 15, 2012
Donna of Lewisburg, TN
Source: consumeraffairs.com

This is an EXTREMELY dangerous range. The burner knobs leak - turn on with
This is an EXTREMELY dangerous range. The burner knobs leak - turn on with just a bump and leak gas. Any slight movement causes the knob to move and allows the gas to leak before the igniter ignites the gas. Has happened THREE times!!!! Has this product been recalled???
Published: July 23, 2014
Cynthia of Oxford, MS
Source: consumeraffairs.com

Purchased this electric range Maytag model YMES8800FZ1 in September 2017. T
Purchased this electric range Maytag model YMES8800FZ1 in September 2017. Thought it was just like my old range with self cleaning mode. Beware! Do Not buy this or anything with this new AquaLift self clean technology. That means youre down on your hands and knées, scrubbing. It doesn’t work. Read all the reviews about this new technology. Salesman never informed us. We innocently bought the range with self cleaning, paid lots of money, for crap! Very upset. Will spread the word for all future buyers, pay attention to the self clean mode on what youre buying, cause no one will tell you. Now trying to reach Maytag, but apparently they don’t care.
Published: February 23, 2018
Gina of Vaudreuil Dorion, QC
Source: consumeraffairs.com

The lid stopped locking just over one year after I purchased a Whirlpool Ca
The lid stopped locking just over one year after I purchased a Whirlpool Cabrio top load washer, which disabled the washer from washing. After investigating, it seems the electronic control board needs to be replaced, which will cost $400 just for the part. I have a large family, including a disabled child, and a washing machine is mandatory necessity that I cant afford to replace after only one year.
Published: June 25, 2012
Elaine of Howell, MI
Source: consumeraffairs.com

Ive had the WDF510PAY dishwasher for 3 years and the circulation pump broke
Ive had the WDF510PAY dishwasher for 3 years and the circulation pump broke. To be more specific the impeller inside the circulation pump warped and then basically got lodged because it became oblong and then it wouldnt pump water to the spray arms etc. I bought a new pump because the warranty only last a year. The pump cost around 90 bucks. After not even 1 full year this factory replacement pump failed again. I reviewed other Whirlpool dishwashers more expensive and I found they all have this same junky circulation pump. Im not sure of a better dishwasher but I would never recommend a Whirlpool dishwasher again. They also use the same circulation pump in Maytag and many other brands. Whirlpool or whoever designed and sold this pump to Whirlpool should be tracked down and beaten. Simple products like dishwashers should last more than 3 years. The technology is nothing new. A product should last 10 years at least.
Published: July 19, 2016
Joe of Martell, NE
Source: consumeraffairs.com

Its just a plain refrigerator. No bells and whistles. It could have more sp
Its just a plain refrigerator. No bells and whistles. It could have more space in the bottom and well as a ice machine or ice maker. Nothing special about it. Just a place to keep food. The light in top could be higher so food does not touch it.
Published: February 15, 2021
Sherrell of Little Rock, Ar, AR
Source: consumeraffairs.com

Purchased Model # wtw5000DW0 Jan 3, 2015. Aug 15, 2015 started leaking wate
Purchased Model # wtw5000DW0 Jan 3, 2015. Aug 15, 2015 started leaking water. Certified technician came to repair. Aug 17 - new transmission. Sept 3 replaced new transmission with another new transmission. Sept 8 called master technician at Whirlpool, needs new clutch assembly. Both technicians stated they dont know what is wrong with the machine. Sept 10 new clutch assembly and agitator replaced. The machine still makes a horrible grinding noise and is unusable. The technician has replaced everything but Whirlpool says it is still fixable. The Master technician has no idea what is wrong with my machine yet he refuses to call it broken. I have been without a washing machine for 3 1/2 weeks. They refuse to offer a return authorization number. I have spoken to a Supervisor on the phone. She states the warranty is for repair. They wont admit their product is a piece of garbage. They have lost a customer. She stated she will put my complaint in a file.
Published: September 10, 2015
Nancy of Cypress, TX
Source: consumeraffairs.com

Purchased a Whirlpool double oven (WGE745COFH) in September 2018. It is now
Purchased a Whirlpool double oven (WGE745COFH) in September 2018. It is now May 2019. After 5 service technicians verified the erratic temperature fluctuations in the ovens, Whirlpool insists that a +25 degree to -25 degree fluctuation in a heating cycle is normal. The motherboard was changed 3 times, and the sensors were changed 3 times, including hard-wiring the last set of sensors. I called Whirlpool and customer service says that is normal. Ever tried baking at a 350 degree setting that fluctuates from 375 degrees down to 312 degrees while trying to maintain a 350 degree setting? I understand there has to be some fluctuation, but either it took a lot of extra time or burned my food consistently. Ridiculous.So, with the help of wonderful people at Lowes (where I purchased the double oven) Whirlpool is refunding my money and Lowes has taken back the slide-in double oven. In my quest to replace it, multiple appliance sellers have told me that all the new ovens having motherboards and sensors have big fluctuations in the oven heating cycles. I find that unacceptable. My husband and other family members have worked daily in an industry where temperatures were critical. They used ovens that could maintain temperature within 5 degrees of set temperature with analog controls. The home consumers are being ripped off with cheap, sub-standard parts making throw away appliances and getting away with it. What do I buy? Havent figured that out yet, but have purchased a countertop toaster oven that bakes beautifully.
Published: May 13, 2019
Kathy of Venice, FL
Source: consumeraffairs.com

We bought this dishwasher because it was rated on the quieter side... It wa
We bought this dishwasher because it was rated on the quieter side... It was purchased in 1999 and is still operating like new. I am amazed it has never broken down. I have wanted to replace it but my wife says Why?
Published: January 8, 2016
W of La Habra, CA
Source: consumeraffairs.com

We purchased a Whirlpool Cabrio washer brand new from Lowes. It did great f
We purchased a Whirlpool Cabrio washer brand new from Lowes. It did great for about 6 months when a terrible grinding noise started. Then it also would not spin dry the clothes - they would come out completely soaked. Repair guy came out and fixed it. Lasted for about 1 year - same thing again. Lasted about 1.5 years this time and now the loud grinding is back and my wife - who Ive heard cuss just a couple times in 20+ years - said, This ** thing sucks. The clothes are soaked. I cant stand this washing machine. So, Off we go to buy a new machine. Definitely not a Whirlpool though. Id give this machine 1 star because it does a decent job for a while but major repairs 3 times in five years is not what I deem an acceptable appliance.
Published: April 14, 2014
Scott of Belvidere, IL
Source: consumeraffairs.com

Whirlpool Duet 3.9 cu ft High-Efficiency WFW9451XW00 - Hear my first experi
Whirlpool Duet 3.9 cu ft High-Efficiency WFW9451XW00 - Hear my first experience with Whirlpool. I purchased a washer machine 30 April 2014. Guess what - machine stop working suddenly on July 30th, just about three months later. I had a lot of guest from overseas. While they visit me, I did not have my washer machine. How embarrassing. It was big mistake to buy Whirlpool. It is all made plastic inside and they uses cheap Chinese material. Anyway, technician came house to check what the problem was... all control system was burned. He ordered almost 10 parts from Whirlpool on 04 August. Whirlpool scheduled delivery for 20 of August. I called them for them to send the parts faster so my guests could wash their clothes. They send them little faster for August 16. After a day, technician was in the house again. I waited about 3 hours for him to fix my machine. He was really nice guy. He put install all new parts. Just in front of me, new parts broke after 5 minute. Whirlpool still did not contact me about their decision. Today is August 26th... I called them 5 time already - Nobody give me useful info. NO Whirlpool, guys - bad service.
Published: August 26, 2014
Huseyin of San Antonio, TX
Source: consumeraffairs.com

After reading all the reviews about the Whirlpool Cabrio washing machine, a
After reading all the reviews about the Whirlpool Cabrio washing machine, all I can say its just a piece of junk. We have replaced the agitator 3 times at $80.00 each, not including labor. Our clothes are never cleaned properly and it always seems to be out of balance. I will never purchase another Whirlpool product.
Published: January 9, 2015
Sheila of Emporia, KS
Source: consumeraffairs.com

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my las
I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).
Published: April 4, 2012
Robert of Cypress, TX
Source: consumeraffairs.com

Weve had our Whirlpool Cabrio washer and dryer just over a year. I like the
Weve had our Whirlpool Cabrio washer and dryer just over a year. I like them both but then we are having problems with our lid. The first one cracked after 9 months and they replaced the lid. Two months later, the new one cracked and they replaced the hinges and lid again. I assure you we are very careful when lowering and lifting the lid. I do 80% and my husband does 20%, and we are very cautious of it especially after the second one broke. Now, I was just putting laundry in and the third one cracked while lifting the lid. There is obviously a problem, and Im wondering if anyone else is having the same issues. Eventually, it will crack all the way through which will cause the glass to pop up and the lid wont lock. I will not buy anything with a glass lid again!
Published: March 27, 2013
Ricky of Myrtle Beach, SC
Source: consumeraffairs.com

Whirlpool washer WTW7800 Cabrio - I bought this machine in Oct 2010 for $90
Whirlpool washer WTW7800 Cabrio - I bought this machine in Oct 2010 for $900.00. This October, the lid started not closing. Next thing I know, the glass is popping out. After waiting on hold for 20 minutes, I was told there is nothing they could do but refer me to a repairman at a cost of $179. The glass is popping out. This is a defect not caused by washing clothes but poor workmanship. I am on hold again. I am calling channel 3 news to do a story and will not stop until it is fixed.
Published: October 8, 2012
Ann of North Haven, CT
Source: consumeraffairs.com

My 4-year old water heater has upper/lower sensor issues for the fourth tim
My 4-year old water heater has upper/lower sensor issues for the fourth time this year. The rep was supposed to send replacement parts to arrive today (day four with no hot water), but the wrong ones were shipped. A different rep called and offered to exchange the unit for a new one. The expense to me will be $350-$450 for the plumber to uninstall my unit, take it to Lowes and bring the new one back to install. The plumber suggested I take my $450 and just buy a new non-Whirlpool unit. He knew immediately that I had a Whirlpool hot water heater because its the most common repaired vendor. Whirlpool should be covering this expense for re-installation of their inferior product. Poor customer service. Day 4 with no hot water during the holidays with no solution in sight short of me purchasing a new hot water heater. Whirlpool finally got the right parts to me and I paid a plumber $190 to install. One week to the day later, my pilot light will not stay lit. No change in ventilation since it has been installed. I will say I have been dealing with their rep Chris on the phone who is extremely nice and I feel sorry for him. But we all have the exact same issue which is not being resolved.
Published: January 12, 2012
Christine of Roxana, IL
Source: consumeraffairs.com

We bought a Whirlpool gas range about a year and half ago. The oven started
We bought a Whirlpool gas range about a year and half ago. The oven started giving lighting problems we had to light with a match every once in a while. Then the broiler igniter started giving same problems so I replaced the igniter, still did not work. Then I tried the control panel, still nothing. The igniters were about 45.00 each. The control panel was 250.00. Then I replaced the spark module and it is now working. Some models the spark module dont control oven and broiler but mine does. That was 200.00. The best thing was the part place I was ordering from would exchange the parts that you try and they also can answer questions either online or by phone, Appliancepartspros.com. My oven model # is wfg371lvs3.
Published: March 23, 2014
mark of Parlin, NJ
Source: consumeraffairs.com

I have previously owned a Maytag washer for 16 years that went through thre
I have previously owned a Maytag washer for 16 years that went through three children. They are older now and two years ago I decided to buy a Whirlpool Cabrio for the upgrade and large capacity. Well just like every other customer that purchased these crappy machine, I now own one of the worst washers in the history of washing machines. It started about 13 months after I bought it and now is completely broken. I am so angry that I spent the amount of money I did to be so disappointed. I have not abused this washer and I can hardly believe the customer service or lack there of, that this company supports. I would hope that people do their research before ever purchasing a whirlpool anything. TERRIBLE COMPANY and my Cabrio is heading to the landfill.... Thanks Whirlpool. YOU SUCK!
Published: June 2, 2014
Angela of Winston Salem, NC
Source: consumeraffairs.com

I feel as though they could use some additional features, it’s also hard
I feel as though they could use some additional features, it’s also hard to change out some of the wiring in the back. I’ve had some issues with smells coming from the washers as well from them. Hopefully they can start to look into tweaking smaller details to improve the overall machine.
Published: May 11, 2020
Kayla of Alpharetta, GA
Source: consumeraffairs.com

I am very upset about this Washing Machine and Dryer. I did my research in
I am very upset about this Washing Machine and Dryer. I did my research in 2012 and found good reviews on drum size, water usage, bells and whistles. I purchased the set in Feb of 2013 (its on Jan of 2017). NOT EVEN 3 years later, I write to say that my washing Machine is ready for replacement! I paid 989.00 for each and last year the Spring on the Glass Top was worn away, I am told because bleach was splashing up in the spring area. Cost to fix with a local repairman... $235.00. Now I noticed a small amount of water on the floor, move the washer and there is a LARGE amount of water Stain and my cycles keep popping up UL. Two separate repairmen (because I didnt believe my trusted first one) tell me the cost for the shot bearings and seals will cost almost as much as a new washer! I am a family of 3. I have a daycare so do a few extra loads, but am not using this any more than average to low use. Not to mention that on top of all of this the computer appears to be shorting out and to order a new panel the repairman places that at an EXTRA 300.00. SO UPSET! The dryer dries very nicely and is quiet however, the motor went out 6 months ago and we replaced that, not wanting to but better fix than scrapping it only 3 years into a product expected to last well over 10! The little clip on the door to lock it is also loose and hardly locks now. The repairman is having trouble even finding the small part. Young Couple Expecting to have a brand new 1900.00 washer dryer set last a long time only to be out of warranty and already needing to buy a new set! DONT EVER BUY A CABRIO WHIRLPOOL.
Published: January 31, 2017
Heather of Perham, MN
Source: consumeraffairs.com

Whirlpool Gold Refrigerator, #GI6FDRXXY07 ICE MAKER PROBLEM - Ever since we
Whirlpool Gold Refrigerator, #GI6FDRXXY07 ICE MAKER PROBLEM - Ever since we bought this ref in 2012, we have been facing problems one after the other. First the refrigerator was shutting off on itself thawing the food the ref & freezer. (When we were on vacation, in summer of 2012 , it was a disaster when we returned home.) This a continuous on going problem... not fixed. Second 2012 Spring the Icemaker shuts off spilling water at the dispenser, when called customer service they sent a technician who replaced the ice maker. But again the icemaker is spilling water or leaking now. Third 2013 Winter, the bottom freezer was leaking and ice buildup at bottom. We have been having problems ever since we got this. WHIRLPOOL YOU HAVE DISAPPOINTED US, its been an exasperating experience. Please Help, its not our fault for your poor design & faulty product.
Published: July 4, 2014
Bashera of Louisville, KY
Source: consumeraffairs.com

The washer never uses enough water ever. The clothes are not clean and it s
The washer never uses enough water ever. The clothes are not clean and it sucks! The clothes are half dry when agitation is going. The bulky setting doesnt clean the clothes either. Ive tried every detergent on the market to see if it would help. No different results. I paid a lot of money in 2015 for this washer and Ive had bad experiences ever since. No change in my water bill since I have to usually wash clothes and towels twice. I want my money back so I can buy a better washer! Im beyond aggravated! I have looked for my receipt but its been awhile. I did get insurance on it. I bought it at Lowes it should be on my card they scan.
Published: December 28, 2017
Holly of French Creek, WV
Source: consumeraffairs.com

The washer can not spin dry, as the unit will not balance. When it spins,
The washer can not spin dry, as the unit will not balance. When it spins, it will get out of balance, and shuts off. I have had a repairman out, but he said he can not fix it, and that this is common with your units, He suggested we get a new one, but not from Whirlpool.
Published: December 5, 2011
Wayne of Surfside, CA
Source: consumeraffairs.com

This product is JUNK!! We replaced out hot water tank 1-07-11. Worked good
This product is JUNK!! We replaced out hot water tank 1-07-11. Worked good for almost 9 months. Then the pilot light keeps going out. We have replaced everything three times already. Now we cant get it lit for nothing. Its blinking 7 times!!! This should not be happening. When you call Whirlpool, you always get some smart ** rep trying to solve your problems over the phone, telling you what its doing. Excuse me, your not here with it, I am. I even had the plumber on the phone, he got so mad at them, he handed me my phone back and said he is not dealing with stupid. They have no clue what they are talking about!! Its crap that we have to pay $30 for them to express mail a part when its the middle of the winter and we have no hot water. Im at my wits end with this hot water tank. Im ready to sue their butts. Sounds like to me by reading all these reviews, a lot of people are having the same issue. We need to do something about this. They had a suite against them but not for my water tank. They were replacing the parts. Ive spent over $1000 from buying it new, having it installed and paying for repairs on the hunk of junk!!!What can we do??? We need to take a stand against Whirlpool. We need to exchange information and contact an attorney and make them pay!!
Published: February 22, 2015
Summer of Reynoldsburg, OH
Source: consumeraffairs.com

I have had the washer for 3 years now and it started to make a loud noise d
I have had the washer for 3 years now and it started to make a loud noise during spin cycle. I made a service call and found out the bearings are damaged. Something that cost this much money should last a lot longer. I have researched on the internet and found this to be the problem for a lot of consumers and would like to see something happen.
Published: December 24, 2011
Jasen of Lee, ma
Source: consumeraffairs.com

Four years ago, my wife and I also purchased a Whirlpool washer and dryer s
Four years ago, my wife and I also purchased a Whirlpool washer and dryer set, washer model no. WTW6600SB2. Within the first year we had to replace both pumps twice, user interface, and control board. (I think that’s what it was called). Of course, that was all covered under warranty. But I to had to wait a week for the part and then another week for the repairman to make it. The user interface and control board had to be replaced because moisture got into the control panel and caused corrosion on the circuit boards which caused them to short out. Then it wasn’t long after warranty ran out, the whole wash tub and drum just dropped to the floor with a full load in it. I don’t remember exactly what was the cause of it, but I do remember it cost me $580 to fix it. Then it wasnt more than two weeks later, the repairman had to come again and replace the control board again. There went another $600 for the parts, labor and service call because this time they had to come from 40 miles away and it’s a minimum fee of $89 just for them to drive up here and another $60 for diagnostics, and then the part and their time to install new board. I paid for this machine twice in the first year and a half. Then after all of that, it was finally working like it should and worked great for about 6 months, then came the UL,LD, and Lid Lock codes over and over unplug, plug in, unplug, plug in. That lasted for about a month, and then all of a sudden, it straightened out. And we only got the occasional UL code. Now in the last year, I have had to replace the drain pump twice and then the drum and motor dropped on the shaft allowing any loose change or other items if accidentally missed during pocket searches to fall into the outer wash tub and get sucked into the drain pump and causing a quarter to be shoot through the drain pump making a hole and caused my laundry room to flood. Well, I decided I wasn’t going to buy another part so I used a plastic repair kit to fix the hole and got it up and running. A week later, the washer won’t wash. It will fill and that’s it. So upon my own diagnostic, I came to the conclusion that it was the user interface that went out due to corrosion I found on it. So for another $120 I can fix it, but I’m not sticking another dime into the washer, nor will I ever buy another Whirlpool appliance. Once all of my Whirlpool appliances die, I will replace them one at a time with LG. I to contacted Whirlpool about my problems and all they did for me was send me an extended warranty offer for 50% off, really that’s it, that’s all I get is a big GFY after all the money I have stuck into this piece of scrap-metal. Well, never again will you have my business as long as I live. Whirlpool, you need to take your hoo-ya and do something about all of these complaints.
Published: January 26, 2012
Chad of Ellendale, ND
Source: consumeraffairs.com

We purchased a Duet from Lowes just a few months ago. Within 2 weeks we had
We purchased a Duet from Lowes just a few months ago. Within 2 weeks we had an inoperable machine. After 2 phone calls a service technician came out and looked it over. He had to come back a total of three times to replace the motherboard. That worked for about six weeks and it died again. He came out again and replaced the motherboard again. Fast forward two months and the machine is once again inoperable. When plugged in, it makes an ominous growling sound but nothing else happens. The idiot who designed this thing has no common sense. Its programmed so that it will LOCK on any failure. Not only has every one of these episodes left us with a load of clothes in there getting moldy, you cant even get to the model number or serial numbers; both of which are only visible inside the rim of the machine.So adding insult to injury, your machine is broken, your clothes are in there getting ruined, and YOU CANT EVEN GET TO THE INFORMATION YOU NEED TO SET UP THE SERVICE CALL. If it had only happened once, Id laugh, but this is the third time and its not funny. We bought this machine because it said proudly made in USA. Next time, Ill support the Korean economy and buy a reliable, durable Samsung. The only positive I can offer is that the Whirlpool live chat person was able to set up the service call for me even though I cant get to the relevant data inside the machine. DONT BUY A WHIRLPOOL WASHER. Despite their legacy and US-feel-good associations, the sad truth is that they are poorly engineered and poorly manufactured.
Published: December 30, 2013
Mark of Weddington, NC
Source: consumeraffairs.com

I also fell for the Consumer Reports BEST BUY of the Whirlpool Cabrio set.
I also fell for the Consumer Reports BEST BUY of the Whirlpool Cabrio set. The dryer has had the heating element replaced 2 times already in 3 years. The washer reads all errors, and the repairman said today, “dont bother fixing, buy a new SPEEDQUEEN.” With the Board going out, and also the faulty bearings--will NEVER buy anything Whirlpool again.
Published: July 26, 2011
Lisa of Lexington, IL
Source: consumeraffairs.com

Two years ago, I bought your new stove. It was under warranty. The computer
Two years ago, I bought your new stove. It was under warranty. The computer is messed up. They came and they did not fix it. Warranty is off. It hasnt worked right since I got this stove. Who is going to make it right? Its only two years old. Fr2 v comes on when turn on. Oven have to turn power off to get it to work. This stove sucks.
Published: January 31, 2012
Charlotte of Christiana, TN
Source: consumeraffairs.com

I bought washing machine Whirlpool Cabrio Model WTW7300XWO two years ago. I
I bought washing machine Whirlpool Cabrio Model WTW7300XWO two years ago. It only lasted 2 years and the tub seal and tub bearing went bad. I called Whirlpool and they wouldnt replace defective part on their dime. I talked to supervisor and they still refused to admit they needed to fix this broken product on their dime and make it last longer than 2 years. They claimed only a 1-year warranty. This is totally unacceptable to have a supposedly good washer that you pay $700 for (manufacturer price $899) last only 2 years! Very, very disappointed! I wouldnt buy from this company again!
Published: January 11, 2013
E of Avon, IN
Source: consumeraffairs.com

Whirlpool Cabrio Washer Model WTW6400SW2 Serial CU0272414: I replaced my wo
Whirlpool Cabrio Washer Model WTW6400SW2 Serial CU0272414: I replaced my wonderful 25+ year old Kenmore washer with the Cabrio, 4 years ago. Within the first year I had to have a computer board replaced that was covered under the warranty. This last 6 months I replaced the suspension rods, was constantly showing that the load was unbalanced. Also have a LD error, long drain, probably because a sensor is bad. Today, restarted a load several times and could never complete the entire cycle. I resorted to unplugging, and starting a drain spin cycle and the washer just flooded my house. So Im done with this unit. Waiting for a class action suit. Lets get started. What type of unit should I buy now. I guess Im going to subscribe to Consumer Report before I buy another. Laundromat for me in the meantime.
Published: February 15, 2014
Patty of Boaz, AL
Source: consumeraffairs.com

I waited years to buy this machine. I hate it!!! I agree with the other bad
I waited years to buy this machine. I hate it!!! I agree with the other bad reviews. It destroys clothes. There is barely enough water in it to cover the bottom of the machine much less the laundry. Even deep water is a joke. It does not clean. I put it on the hottest water temp and I can put my hand in there and it is barely warm (it is not my hot water heater). My lightweight comforters come out all tacky and grungy in the middle. The softener dispenser (I use vinegar) dumps in the laundry (no it is not over full) (no I do not slam it shut). I can not let anything soak because the machine will drain after a few minutes and all my detergent, scent crystals etc. are all wasted. I feel like I have to take a survey and complete a questionnaire every time I do laundry. Can someone tell me how to put a comforter in there and leave that little middle eye open? They say the water saver is government regulated? Yup I need the government to do my laundry... I believe in saving water. I have a water saver toilet, shower, faucets. However I can not clean dirty jeans in a gallon of water. My clothes do not even get wet. How does whirlpool get away with advertising this machine can do king size comforter? The gentle cycle will tear apart anything I might put in there because there is no water and that blooming thing just twist and turns so it tears anything delicate. This is the 21st century. I think I should not have to babysit my washing machine. Why should I have to readjust everything in hopes it might be almost clean??? Place this here and that there, wipe the lint out before doing dark laundry. This machine belongs in the dark ages. It is so complicated yet it achieves nothing. A big rip off. I so tired of crying over this purchase. I hate this machine!!!
Published: May 11, 2016
ANN of Santee, SC
Source: consumeraffairs.com

Large tub capacity. Door opens wide without stopping. White Finish has not
Large tub capacity. Door opens wide without stopping. White Finish has not faded or chipped. Quiet and rarely makes noise even when overloaded. Machine bought 12 years ago and has never needed a repair visit. It has been moved from 2 different locations by using the special brackets. Easy to use detergent holder and fabric softener.
Published: May 14, 2020
Pat of Atlanta, GA
Source: consumeraffairs.com

Bought Whirlpool Gold refrigerator, microwave, and stove. The bottom where
Bought Whirlpool Gold refrigerator, microwave, and stove. The bottom where the freezer is located leaks if you dont slam the drawer shut - many times leaking regardless. The microwave needs to be unplugged/reset about once a month or so because the power dies - light comes on, food rotates, no heat. And the small stove light indicating the burner is on for the front left burner suddenly doesnt light up. 0 for 3 on satisfaction. Appliances are 2-3 years old. Did not get extended warranty. Everyone tries to get you to buy but didnt realize I was buying junk. Will not recommend or buy this brand again.
Published: January 9, 2015
Michael of Castleton, NY
Source: consumeraffairs.com

As a consumer, Im very disappointed in this Whirlpool Cabrio Platinum washe
As a consumer, Im very disappointed in this Whirlpool Cabrio Platinum washer. It does NOT clean your clothes. Many times Im washing my clothes twice, only loading a 1/3 of a load of laundry in it because of this problem. No matter what you do, it just doesnt clean your clothes. Has anyone considered putting a law-suit against the company. They will NOT stand behind this issue, NOR replace your washer with something that works. Maybe that is what it will take. DO NOT ever ever ever ever ever ever buy this piece of crap washing machine. You will waste your money, your time, your extra detergent it takes to wash your clothes AND the cost of the machine too! The MILDEW SMELL is horrible and no matter what you do you CANT GET IT OUT! Ive tried it all. Im just angry because I had to save money to purchase this set and it is a piece of crap! The customer service is just a runaround, they wont help you! They will just give excuse after excuse. They need to replace EVERY ONE of our washers with something that works!!! For the cost of this machine alone, they should do something to resolve this issue!
Published: May 25, 2016
Debi of Wilburton, OK
Source: consumeraffairs.com

My hot water tank wont stay lit. I replaced the heating element, and the th
My hot water tank wont stay lit. I replaced the heating element, and the thermo couple. It will light up now but it only stays on for about 10 minutes.
Published: October 27, 2011
Shawn of Marietta, OH
Source: consumeraffairs.com

My new Whirlpool Stove, has two grill like tops, heavy duty and awesome loo
My new Whirlpool Stove, has two grill like tops, heavy duty and awesome looking. It has a special burner to keep food warm, a stainless steel front and bottom drawer for broiler storage. Broiler is also on top in oven, broiler flame.
Published: January 5, 2017
Kathy of Celina, Ohio
Source: consumeraffairs.com

I have had my washing Machines since 2011 and have had continuous problems
I have had my washing Machines since 2011 and have had continuous problems with the washing machine during spin cycle sounding like a freight train going through my house. Whirlpool has had people to my house 5 times to fix. When warranty was up in 2012, I was told they would continue to cover this particular issue. They came out again in April 2013 and now I am being told, Too bad; if you want fixed then you will need to pay for it.
Published: April 1, 2014
Katrina of Smyrna, TN
Source: consumeraffairs.com

Owner of 20 apartments, 16 of them have electric water heaters and 4 have n
Owner of 20 apartments, 16 of them have electric water heaters and 4 have natural gas units. Have replaced over the years all 20 water heaters. 19 of them were replaced with Whirlpool units bought at our local Lowes. It is my opinion that they are very unreliable. The tanks rust out in NO time. The electric units last just a little better than the gas units but still terrible. Of the 4 gas units so far I have had to replace 3 of them and the longest one lasted 6 years and 7 months!! One of them was just over 6 years and the other was 9 days away from warranty expiring. They replaced that one. If you have no other choice make sure to buy extended warranty if available. They just dont last!!
Published: October 14, 2020
James of Campbellsville, KY
Source: consumeraffairs.com

We purchased the Cabrio washer and dryer due to the companys past reputatio
We purchased the Cabrio washer and dryer due to the companys past reputation and our own past experience with Whirlpool appliances fully expecting to receive great performance and durability. We have had the pair just about 2 years and the washer started experiencing problems during the spin cycle. The unit would get out of balance easily and then it would stop without spinning, leaving the clothes very wet. Well, as our past experience had indicated to us the washer is usually much more reliable than the dryer, or thats the way it had been for us. So we only purchased the extended warranty on the dryer. Not being covered on the washer we located a local technician and he promptly diagnosed the problem as the transmission failed causing the noisy bearing and the failure of the unit to spin properly.Our tech quickly repaired the unit but this failure disappointed me to the point of contacting Whirlpool. Thats where I came upon this site and saw the multitude of complainers with the same type of problems and some that are worse than ours. Our purpose in this review is to add to the 1100 or more reviews that report the same kind of issues. We are now in the same mindset as the 1100. Will we ever buy another Whirlpool? Probably not, especially since it doesnt look like Whirlpool wants to stand with their customers to make it right. Customer support is just as important to us as the reliability we seek. I would much rather spend a bit more in the price than replace or repair the unit after the purchase. A little economics lesson for our friends at Whirlpool is that if you abandon your 1100 customers you will save about $440,000.00, but those 1100 will tell everyone they know of their problems with that product and as a result many thousands will never purchase a Whirlpool. So if we all influence 5 of our friends not to buy, then 1100 X 5 = 5500 people X an average price of $800 which equals about 4.4 million dollars of lost sales. Seems like a no brainer to want to stand behind your customers. We dont believe that any washing machine on the market should fail after a few months to 2 years. These products should be built to last many years and the maker of these products should have that goal.
Published: February 13, 2014
Ted of San Angelo, TX
Source: consumeraffairs.com

I purchase newly Whirlpool washing machine but it was not working from the
I purchase newly Whirlpool washing machine but it was not working from the first day of my purchase. So many service Engineer came but nobody can solve the problem, so I suggest to all please don’t buy washing machine from Whirlpool. I am very disappointed from this company.
Published: May 8, 2018
Shashank of Lucknow, Other
Source: consumeraffairs.com

In January 2011, we bought several appliances and a refrigerator was one of
In January 2011, we bought several appliances and a refrigerator was one of them. The model number is G15VAXVQ01 which is a side by side, French Door Ref with water and ice on outside. We have had problems with the very cheap plastic drawers that are at the bottom of the refrigerator to hold vegetables and meat. We have to be extremely careful so they will not break when opening the drawers. As of late, the fruit and vegetables have been freezing. I went to change the temperature on the outside gauge and dropped the control to 33 degrees and it stuck there. I tried to unplug the refrigerator to reboot the system, to no avail. The temperature is stuck at 33 degrees which will freeze most of our food in a few hours. The freezer side temperature gauge does work.We also have problems with the ice/water machine. I pushed the water button a week ago and from then on, I couldnt get the ice to come on. I did unplug the refrigerator to reboot and then I was able to switch over to the ice, but I could not get back to the water side. Also, there is no crusher on this machine so the ice comes out in chunks. If we had to do over again, we would not buy a Whirlpool as it appears that they are not interested anymore in quality products and consider cheap junk something to be desired. Not by us! We will get this albatross fixed and see about getting rid of it. It is a buyer beware market so I suggest others beware of Whirlpool products.
Published: September 12, 2012
Dr. Thomas of Billings, MT
Source: consumeraffairs.com

Wish there was a no stars. This is the second refrigerator in 3 yrs or less
Wish there was a no stars. This is the second refrigerator in 3 yrs or less. Had first one for less than 8 months before it stopped working. Needed to be replaced and now second one made it a little over a year and now just stopped working. Washers were also garbage and I’ve been slowly buying all new appliances with other brands. I’ll never buy a single Whirlpool product ever again.
Published: October 3, 2017
Mikey of Peoria, AZ
Source: consumeraffairs.com

I have had problems with my electric range (Whirlpool) since day one. It al
I have had problems with my electric range (Whirlpool) since day one. It always ran hot. I wrote letters to Whirlpool and received one very condescending phone call. Now two days before Thanksgiving it is running terribly hot from 350 to 500 degrees. When I called Whirlpool they said the best they could do was offer me a maintenance plan for 293.00.
Published: November 22, 2016
georgette of Pleasantville, NY
Source: consumeraffairs.com

I purchased a brand new Whirlpool Cabrio washer and dryer set not even 2 ye
I purchased a brand new Whirlpool Cabrio washer and dryer set not even 2 years prior. When I first started using it, I pulled shirts out of the wash after being ran through and found deodorant marks still on the inside of the shirts. I had to wash all of my loads on heavy soil and still had to run some loads through more than once. The wash machine quit working about 1 month ago, so I had a service man out to look at it. It ended up being the control panel and the part itself was going to cost me $300 and by the time I paid to have it repaired, the total cost was just under $400. The service man proceeded to tell me that Whirlpool had another company actually make the control panels for the Cabrio model and he has serviced several of these washers and when he would repair one part, another part would stop working. I was very upset and bought a new wash machine. I would like to add, I am a single mom with a 2 1/2 year old, so the wash machine was not used excessively in any way. I dont work outside so my clothes are never soiled heavily. Needless to say, my washer was not under warranty so Whirlpool couldnt do anything for me. A wash machine should last longer than less than 2 years. I would not recommend this model to anyone. And for Whirlpool to put their name on such a poor product is very disappointing since I have had good experiences with their products in the past.
Published: February 7, 2013
Krista of Ashley, MS
Source: consumeraffairs.com

We bought a Whirlpool French Door refrigerator in July of 2018 and it has g
We bought a Whirlpool French Door refrigerator in July of 2018 and it has gone out twice (quit cooling and has completely frozen over). The first time it went out at 6 months and the second was two days after the factory warranty expired (the warranty for the Whirlpool repair company lasted only 90 days for parts and labor which is useless). I’ve called the company to come take a look and it will cost over $100 just to have someone come out since we are outside the factory warranty window by four whole days. I was basically told there is nothing they will do even though the same problem keeps happening. This refrigerator was brand new and didn’t even make it six months.Now we will need to either pay hundreds of dollars for repairs (knowing that the issue will likely happen again) or buy a new refrigerator. Even though we have barely had this appliance a year. I will never, ever buy Whirlpool products ever again. I also posted my negative rev on their official website and it never got published. They only show their 4-5 star reviews (all of which say the customer has been incentivized in some way). This is a misleading and sneaky process.
Published: August 2, 2019
Jennifer of Buda, TX
Source: consumeraffairs.com

I have 1 month old gas range, bought from Costco.. I was cooking chicken an
I have 1 month old gas range, bought from Costco.. I was cooking chicken and it is just explode.. Called to Whirlpool company and they act like they don’t really care about it... I am shocked.. I search google and you can find other incidents with whirlpool explosion.. Just google it.. I am sooo upset with this company.. My kids were with me when it happened.. Do not buy whirlpool products...
Published: January 14, 2020
Anastasiia of Brooklyn, NY
Source: consumeraffairs.com

Only problem is you have to open door to access functions. 30 second increm
Only problem is you have to open door to access functions. 30 second increments and stop are on outside. Beautiful to look at and inside is easy to clean. 4 fan levels, vent inside or outside. 2 light settings. Nice and bright. Low profile over stove but big enough to hold large casseroles.
Published: July 13, 2019
Lisa of Sodus Point, NY
Source: consumeraffairs.com

It was about 6 years after purchase that the ice maker completely quit maki
It was about 6 years after purchase that the ice maker completely quit making ice. To change the filter you have to get down on your hands and knees to do so. If youre elderly, this can cause a problem. Overall, it was a good refrigerator.
Published: September 4, 2019
S. S. of Pacoima, CA
Source: consumeraffairs.com

Takes 2 or 3 full cycles to dry small load. Big disappointment, drying is s
Takes 2 or 3 full cycles to dry small load. Big disappointment, drying is such a horrible experience since the clothes never dry when I expect them to. Not satisfied at all.
Published: February 14, 2019
Dorothy of Conroe, TX
Source: consumeraffairs.com

I have front loader, Ive left the door open after washes, run cleaning cycl
I have front loader, Ive left the door open after washes, run cleaning cycle once a month, never had any issues, like with anything. If you take care and service it regularly it will last a lifetime.
Published: May 17, 2020
Jennie Lee of Homosassa Springs, FL
Source: consumeraffairs.com

Avoid Whirlpool refrigerators and dishwashers. Fridge sounds like someoneâ€
Avoid Whirlpool refrigerators and dishwashers. Fridge sounds like someone’s trying to get out. Repair person said it’s icemaker and typical. Dishwasher has little friction gaskets that keeps the door from falling open. They’ve been replaced twice and found one on floor today. Plastic end of slider for upper shelf keeps falling off repairman replaced it showed me how to put it back on. This falls off regularly. Range has coils underliner of oven. Takes forever to preheat and self cleaner cycle is a joke. Million dollar condo with upgraded crap appliances.
Published: December 29, 2018
William of Naples, FL
Source: consumeraffairs.com

This is my second water heater in three years. The problem is the thermocou
This is my second water heater in three years. The problem is the thermocouple thermostat. Also, when I drain the water, it comes out of the heater black because of the corrosion in side. I spoke to people in the company, and they were nasty to me. This happened to my two heaters in 2 1/2 years. Please, do not buy a Whirlpool heater.
Published: October 1, 2011
Susan of North bergen, nj
Source: consumeraffairs.com

We recently bought a home and our dishwasher came with the home. We saw our
We recently bought a home and our dishwasher came with the home. We saw our basement leaking and got 2 plumbers come over and check the pipes out, paying almost $600, only to realize that the leak was actually from the broken plastic in our dishwasher, and not any pipe. When we called the Customer Service to get it replaced as it comes with a 20 year warranty on the plastic body, they said they would replace the part, but I would have to pay $81 for the first 15 min & $19 every additional 15 min. for labor, which means I would end up paying at least close to $400 or more, depending on how long the technician takes to replace the fiber body. Neither their policy nor warranty make any sense to me. Its frustrating to see that in spite of being covered, I would be the one paying money out of my pocket.
Published: July 14, 2014
Neha of Brantford, ON
Source: consumeraffairs.com

I purchased a 40-gal Whirlpool water heater model 40t91-403 last week and p
I purchased a 40-gal Whirlpool water heater model 40t91-403 last week and paid a plumber to have it installed. The old one (GE 40 gal) worked fine except for a leak. The new one used all of the old connections except the 2-inch in and out pipes. Same connections, hot, cold and gas. At first I got about a quart of hot water and then all cold. Whirlpool changed the valve and cold water pipe (inside the tank) and still the same. They are trying to tell me that the tank is fine - I have a plumbing problem. Two plumbers have told me different, but still they insist. Yes, I am upset. The old GE, even with a leak, performed better!
Published: May 29, 2013
Sam of Columbus, OH
Source: consumeraffairs.com

I purchased a refrigerator Model# WRF736SDAW12 on 8/9/14 and from day two,
I purchased a refrigerator Model# WRF736SDAW12 on 8/9/14 and from day two, Ive had nothing but problems with the ice maker. We NEVER use crushed ice, but we get a lot of crushed along with cubed and crushed/shards of ice all over my fridge, hands and floor. My daughter (wearing her heels) already slipped and fell while walking past the fridge, not realizing that there was ice lying on the floor because my floor is light/multicolored, so we cant see the ice.After several calls, the repair person replaced all the components of the ice maker and the repair person was told (2/26/15) from the Whirlpool tech that we would just have to live with the problem because its normal and he was advised to tell me to get a larger glass. The repair person looked at my glass, seeing that it was already large, shook his head and said Whirlpool must want me to start using a bowl to catch all the ice. I couldnt believe it?! I bought this fridge expecting to receive ONLY cubed ice and yet I dont, so Im sure why they put that cubed feature on there when I cant utilize it. I only want a little ice, but the first thing that comes out is the crushed ice, and in order for me to receive more cubed ice, I have to fill up the entire cup that includes the crushed/shards of ice which floats to the top and ends up in my mouth. Thats the purpose of me selecting cubed, so I dont have to drink it!After the repair man left, I called customer service (2/26/15) and she told me that ice gets stuck in the chute?, so thats why I get crushed ice, but its normal she says. How is that normal? Please read all the reviews/complaints from both the Whirlpools and on Home Depots website for this model and you’ll see this is a problem, there is a flaw in the design.I cant believe a big company such as Whirlpool would treat me so poorly and brush me off like this. After the many posts I put on their Facebook page, they over and over say they will be in contact with me. I have yet to hear from them. I found another story on Pissed Consumer where a senior fell due to the ice falling all over the floor, so its not just me that it has happened to. Theyre putting people in a hazardous situation and they dont care.I have an autistic son who gets ice constantly, I can’t supervise his every move and I’m not able to keep up with his dropped ice nor can he remember to look down for it. I’m concerned that next time my daughter falls; she won’t be so lucky and could sprain or break something. How about my visitors? Do I worry about them suing me when they fall? I’m not so annoyed at the fact that I step on water with my dry socks or the 24/7 noise from the motor or the left door not shutting all the way than I am with the safety of my family.
Published: March 5, 2015
annette of Palmdale, CA
Source: consumeraffairs.com

I purchased a high-end Whirlpool dishwasher (WDT710PAYM) a few months ago t
I purchased a high-end Whirlpool dishwasher (WDT710PAYM) a few months ago thinking I was making a wise upgrade. Poor design and it wont dry dishes or properly wash utensils when theyre placed in the utensil rack on the door panel. The unit heavily condenses after using heat dry mode and large water droplets completely cover the top of the inside cabinet. Eventually, they all fall down into the dishes and you now have wet dishes again. The Whirlpool tech’s response was to scratch the cabinet plastic with a scratchy pad, smear rinse aid over the plastic cabinet and that should stop droplets from forming. Whirlpool’s customer service told me they shouldve never told me that and what I should do is be there during the drying cycle and open the cabinet door to let the steam out. This is completely ludicrous. Dont walk but run away from Whirlpool products.
Published: April 27, 2012
Glen of Austin, TX
Source: consumeraffairs.com

Fridge is over 20 years old. Definitely got money worth. Need to replace al
Fridge is over 20 years old. Definitely got money worth. Need to replace all appliances soon??? Which model next. So many models to choose. Love one with freezer on bottom.
Published: April 23, 2018
Patricia of Brockton, 189 North Ave
Source: consumeraffairs.com

Purchased this simple 30 wide fridge July 2017 to fit a short kitchen slot.
Purchased this simple 30 wide fridge July 2017 to fit a short kitchen slot. It worked adequately, but it only had 3 temp settings. The highest setting was too warm and coldest froze food in the fridge within days. The middle setting was a little cold but the best option. Food in the back did occasionally freeze and we had to be careful for vegetables in the drawer freezing. Often we wrapped lettuce and more fragile veggies in towels to absorb moisture and slow down freezing. Two years after buying - almost to the day - the fridge stopped cooling below 45F. The freezer still worked, so I thought it might be fixable. I tried some DIY repairs from a couple of websites but nothing worked. Within a week, the fridge temps were up to 50-55F. I gave up on buying ice and keeping food in coolers. I bought a GE and havent looked back.
Published: May 25, 2019
SC of Denver, CO
Source: consumeraffairs.com

My husband and I, purchased this washer on November last year, I used twice
My husband and I, purchased this washer on November last year, I used twice before and I noticed that the clothes felt hot, but the cycle was COLD water. Now use it again until June 2015. In every cycle the clothes were hot, I started calling to get an appointment in June at the 1800-253-1301, but the system was down twice. Then in July then again the system was down, then August 10, system was down. I did not wait more and called back the next day, August 11, got appointment for the 20. A technician came, he told me that the hoses was switched, but I know the hoses was installed correctly, my husband was here at the installation. He knows the proper installation of the washers.
Published: August 23, 2015
Sandra of Cibolo, TX
Source: consumeraffairs.com

I purchased a Whirlpool dishwasher from Home Depot on 2/5/2015. It was deli
I purchased a Whirlpool dishwasher from Home Depot on 2/5/2015. It was delivered damaged on 2/9/2015. Home Depot refused to take it back and Whirlpool sent a tech out to see the damage. I told them I did not want a refurbished dishwasher that I paid almost $1000 for. Whirlpool advised Home Depot that the machine can be repaired. Once again I told both whirlpool and Home Depot that I did not want this dishwasher and to pick it up. Home Depot stated that there would be a 15 percent restocking fee along with a $65 to pick up the washer. Why should we have to pay anything? I am so disgusted for the treatment I received.
Published: February 22, 2015
Patricia of Peabody, MA
Source: consumeraffairs.com

We bought this washer from Sears with big hope. Within the first year, we h
We bought this washer from Sears with big hope. Within the first year, we had 14 service call covered by the warranty but required 2 to 3 weeks in doing without. Whirlpool replaced the washer at no charge but continued to have various issues over the years. The new one is the control module that Whirlpool knew was faulty but did not let their customers know. The control module went over the weekend but I repaired it myself and do not have any more issues. I literally went in and tightened all of the hardware, removed and install the pulleys, motors pumps and replaced a lot of keep components with better quality. Guess that year the CEO made only 20 million rather than 19 million. Being an American company I was disappointed by the consumer relations people but everything is a throw away nowadays. Will not buy a Maytag or Whirlpool product again. Where has American product pride gone?
Published: February 7, 2014
Larry of Willimantic, CT
Source: consumeraffairs.com

My elderly mother purchased a Whirlpool Cabrio washing machine in 2013 (Mod
My elderly mother purchased a Whirlpool Cabrio washing machine in 2013 (Model Number WTW8600YW1). It never filled properly with water. It evolved to a sensor and circuit board issue that Whirlpool never totally remedied. Hence, the machine never worked properly. This 800 dollar purchase on an elderly persons limited budget had to be utilized minimally. Now fast forward in 2015, even with minimal usage and white glove handling, the machine is displaying an F51 error. You guessed it, Whirlpool will not remedy the issue, although it is well-documented to be a widespread complaint hence clearly a product defect. Shame on Whirlpool, their business practices, and what amounts to theft of an elderly womans finite income. I have advised my mother to trash the useless Whirlpool appliance and purchase a Kenmore washing machine, of which I have been the proud owner for 10 years, doing laundry for a family of 5.
Published: December 8, 2015
Kim of Yonkers, NY
Source: consumeraffairs.com

My fridge is only 8 months old and stopped working about 5 weeks ago. They
My fridge is only 8 months old and stopped working about 5 weeks ago. They have sent repair techs out 5 times, replaced the compressor, condenser, some fan thing and evaporator. It worked for 2 days then the compressor started leaking again. Ive lost 2 refrigerator full of groceries. It damaged my floor. I was unable to have family over for Christmas and Ive been using a mini fridge. The Whirlpool customer service people have been no help and some have been very rude. I have no idea when this will ever be fixed. There is no way I would ever buy any appliance from Whirlpool again. Terrible experience.
Published: January 5, 2017
Sherry of Pinellas Park, FL
Source: consumeraffairs.com

This Whirlpool Water heater was purchased through Lowes on March 29, 2011.
This Whirlpool Water heater was purchased through Lowes on March 29, 2011. This past weekend, water started leaking out of the thermostat/natural gas control located on the side of the tank. I called a plumber to take a look. He stated that a new thermostat/natural gas control was needed. Although the tank has a 12 year warranty, this item does not. Whirlpool did agree to replace the part but would charge me $30 to overnight the item which still would have taken 4 days because of a weekend. To install the item would have cost me almost $500.00.To purchase a new Rheem Water heater was $999. I chose the second choice as the first choice would have still left me with a subpar water heater obviously already out of warranty. The reason for my review is that I saw the number of complaints on the failure of this part. When I purchased this water heater, it was the better model due to the 12 year tank warranty. What use is the tank warranty when the other items dont last? There should be some type of reimbursement but Im not holding my breath. Please buy a contractor grade water heater and not the cheaper models.
Published: December 19, 2016
Mark of Cleveland, OH
Source: consumeraffairs.com

I did not purchase the washer (Cabrio Top Load Clothes Washer) but inherite
I did not purchase the washer (Cabrio Top Load Clothes Washer) but inherited it in a home sale. Never had a non agitator. I was excited for this new washer. After a week I knew why they left it! My clothes did not seem clean; stains were still on them, when I used the delicate cycle a pair of pants went in folded and came out folded!!! I also would have to redistribute the clothes every time I had a load that was larger than five pieces, because it would stop. I would actually have to take clothes out and spin what was remaining then put those in the dryer and put the other clothes back in and spin those again. I was told I needed to use OxiClean on top of my normal detergent in order to get my clothes clean. Never again will I purchase a Whirlpool. Just bought an LG; fingers crossed.
Published: July 1, 2017
Robyn of Montverde, FL
Source: consumeraffairs.com

Its a great machine but the temperature control button is easily moved at t
Its a great machine but the temperature control button is easily moved at times. The machine does a great job in washing clothes. Ive had mine for 10 years now and hope that I never have to replace it.
Published: May 11, 2020
Pamela of Cartersville, GA
Source: consumeraffairs.com

We have a Whirlpool Gold fridge that was manufactured in 2009. MOD: GS2KVAX
We have a Whirlpool Gold fridge that was manufactured in 2009. MOD: GS2KVAXS01. SER: HRY0570897 and it has not been cooling properly for the last few weeks. Some days it is fine, the next day not and we have had to throw our a lot of rotting food. We got the fridge checked out and were told the Electronic Control Box for the fridge was not working. My question is, why would a Whirlpool Gold fridge that costs $1800 or so have such a large issue with 3 years? Its practically a brand new fridge and Im outraged that a large part of the fridge is not working. I understand parts break and there is warranty but its pretty bad that after the warranty expires the control box would become defective. I have been a loyal Whirlpool customer and solely buy the brand and this break upsets me very much. Especially since replacing the part will cost me $400 plus labor, we are talking about a part costing 30% of the total fridge cost! That is ridiculous. I am hoping there is something you can do to rectify this, as a fridge manufactured by what I thought was a great company should not cause such an issue and I would like to continue to buy Whirlpool products but not if this is the case.We have called Whirlpool customer service many times to be ignored, berated, told I cannot speak to a supervisor and nothing will be done. Never in my entire life have I ever known a company so horrible to exist. I have had bad service before but this takes the cake. Plus, no company that I have ever dealt with would ignore you and not provide any discount or remedy. I cant believe this is a big brand with the way they carry on. You would assume they would be some one person owned company who doesn’t have a penny to spare. I don’t respect this company at all and expect a resolution because they are truly insulting in all the channels.
Published: July 31, 2012
Shenba of Toronto, ON
Source: consumeraffairs.com

We purchased a 4.8 Cu FT High Efficiency Front Load Washer in February of 2
We purchased a 4.8 Cu FT High Efficiency Front Load Washer in February of 2016. What a nightmare. Just a few months after having it, we kept getting an E3 error message that would not go away. After 2 weeks of waiting before a tech could come out there replaced a door mechanism said it would be fine. After the next wash same thing, same problem. Could not even open the door to get my laundry out. Again they could not get a tech out for at least 2 weeks so Im stuck with the cost of getting my laundry done elsewhere. This time it was the motherboard. Had to wait a week for that to be shipped out. This was all completed in June 2016. We are now the beginning of September and same problem. Again we are told at least 1-2 weeks to get a tech out. Seriously Whirlpool, we are your customer. I have a family and we need to wash our clothes. We spent $1200 on this machine only to have to take our laundry to a public laundry mat because your machine keeps breaking down. They will not replace the machine even though this is the 3rd time with the same problem. The customer service is horrible. They are not willing to help in any way to get this fixed much sooner for her or give us a new machine. This one is obviously a lemon! I will never purchase any Whirlpool appliance again and I suggest based on some of the reviews on here no one does. Next appliance I buy I will do more research for sure.
Published: September 6, 2016
Johnna of Edmonton, AB
Source: consumeraffairs.com

I am writing to inform you of my dissatisfaction with the Whirlpool Duet wa
I am writing to inform you of my dissatisfaction with the Whirlpool Duet washer and dryer I purchased in December of 2011. The model and serial numbers are YWED94HEXL0/M12602088 and WFW94HEXL2/c12350046. After using them for several months, I have found that the performance of the washer and dryer to be poor. I find the clothes do not come out very clean. I used my mother-in-law’s GE washer to compare and found that the clothes came out much cleaner in her washer. I was astonished at the difference. The white clothes, especially, were so much cleaner than in my washer in which white clothes, especially, come out looking like they have not even been washed. I am unhappy with the dryer as well, which continues to shrink my clothes a lot. I am distraught with this situation as this was a big purchase for me. I believe the quality of the washer and dryer is simply poor and I would like an exchange with a better quality set which actually cleans my clothes. I rely heavily on my washer/dryer as I have three young boys who go through a lot of clothes. Please let me know what can be done on your end. Thank you kindly.
Published: September 6, 2012
Arif of Richmond Hill, ON
Source: consumeraffairs.com

Im no longer buying Whirlpool products. They do not all up and are made lik
Im no longer buying Whirlpool products. They do not all up and are made like crap. My Cabrio washer being the most recent problem. Hinges broke on the lid and the drum spring broke. Out the door it goes! Im having my American made Speed Queen delivered tomorrow, the last Speed Queen I owned last over 30 years.
Published: November 5, 2015
sharon of Indialantic, FL
Source: consumeraffairs.com

We purchased our 4 French door refrigerator in November 2014. It started ma
We purchased our 4 French door refrigerator in November 2014. It started making a loud noise, like an air compressor about a month ago. So loud that when we are watching TV in the bedroom we have to close the door! It continued to get louder and more frequent so I called Sears. It is under warranty so they sent a repairman out. When he came, he said it was because we had the refrigerator too cold & it was causing ice to be stuck around the fan??? We had it at 5 and the coldest is 7... He suggested we put it on 3. 2 days later and it is making the same noise again. Will be calling Sears again. I saw a similar review saying the same thing!!!! This is a five month old refrigerator! Very disappointed in product and service.
Published: June 17, 2015
Alexis of St. Gabriel, LA
Source: consumeraffairs.com

Bought the Duet front loader washer and dryer. Nothing but problems and rep
Bought the Duet front loader washer and dryer. Nothing but problems and repairs. When I decided to throw in the towel and buy new machines my repair man convinced me to buy Whirlpool again - Cabrio. Said they are amazing. Love them except the holes in my shirts. I bag my delicates but apparently I have to bag everything. So sorry I bought them. There was a day when you could count on Whirlpool. Replacing my crappy Whirlpool gold refrigerator right now too. Hoping LG will be better. Already replaced my Whirlpool dishwasher. Went to Maytag. This company has gone downhill. My mom had these appliances for 20 plus years - I spend thousands and cant get 5 years!!! Dont buy Whirlpool!
Published: July 5, 2017
Robin of Chandler, AZ
Source: consumeraffairs.com

Visa MasterCard

Site Secured By The Website Guardian
TOP