Appliance Types


Appliance Brands


Article Categories


More Articles


Whirlpool Appliances
Whirlpool Appliances

Whirlpool Appliance Troubleshooting

The company markets Whirlpool, Maytag, KitchenAid, JennAir, Amana, Gladiator GarageWorks, Inglis, Estate, Brastemp, Bauknecht, Ignis, Indesit, and Consul. Their website also mentions Diqua, Affresh, Acros, and Yummly brands.


Air Conditioner Troubleshooting

Whirlpool Air Conditioner Not Cooling 
If the air filter is clogged, air cannot flow properly through the air conditioner. This greatly reduces the cooling capacity of the air conditioner. In addition, if the air filter is clogged, the evaporator coils will frost over. To remove debris from the air filter, try cleaning the filter. If it is not possible to clean the air filter, replace it. 

Whirlpool Air Conditioner Fan Not Working 
The dual shaft fan motor (or circulation fan motor) might be defective. The circulation fan motor has two fan blades: one on either side of the motor. On one side, the fan blade draws in outside air over the condensing coil to dissipate the heat. On the other side, the fan blade directs the air over the evaporator coil. The dual shaft fan motor has bearings that can loosen or bind over time. To determine if the motor bearings are defective, wiggle the motor shaft. If the motor shaft is loose, or if it won’t turn at all, replace the fan motor. 

Whirlpool Air Conditioner Compressor Won't Run 
The temperature control board provides voltage to the fan motor and compressor. If the control board is defective, it may stop providing voltage to the compressor. Control boards are often misdiagnosed. Before replacing the temperature control board, make sure you check more commonly defective parts—particularly the compressor overload, capacitor and the compressor itself. If you are certain that all of the other components are working properly, replace the temperature control board. 

Whirlpool Air Conditioner Won't Turn Off 
The condenser coils dissipate the heat as the refrigerant passes through the coils. If the condenser coils are dirty, they won’t be able to dissipate the heat as effectively. As debris builds up on the coils, the air conditioner will become less efficient, causing the air conditioner to work harder to cool down. If the coils are significantly dirty, the air conditioner will not be able to maintain the proper temperature, and the compressor will run continuously in an attempt to cool the room. Check the condenser coils to determine if they are dirty. If the condenser coils are dirty, clean them. 

Whirlpool Air Conditioner is Loud or Noisy 
When the compressor is wearing out, it generates more noise than usual. When this happens, it is not necessary to replace the compressor—compressors often last for years after they become noisy. However, if you would prefer to have a new compressor, have a licensed professional replace it. 

Whirlpool Air Conditioner Leaking Water 
If the window or through-wall air conditioner is leaking water from the front, this indicates that the air conditioner is leaning too far forward. The air conditioner is designed to expel the condensate water from the back of the unit. Because of this, the air conditioner must be installed so that it leans back on a 1-2 degree angle.


Dishwasher Troubleshooting

Beginning Steps 
Before starting any troubleshooting, make sure you have allowed the dishwasher to complete its full cycle. A Whirlpool Gold dishwasher can run for more than three hours before its cycle is complete. 
Make sure you are properly loading the dishes into the dishwasher. The detergent dispenser should be free from blockage, and there should be enough distance between the dishes for water and detergent to flow freely. 
If your dishwasher won't start, make sure the door is tightly closed and the latch is locked. 

Basic Troubleshooting 
If your dishes aren't getting clean, make sure you are using a high-quality dishwasher detergent. Use the recommended amount for your specific Whirlpool Gold dishwasher. Too much or too little can prevent your dishes from getting clean or leave spots on your dishes. 
If your dishes are coming out still wet, make sure you are using a quality rinse agent. Whirlpool Gold dishwashers rely on a rinse agent, such as Jet Dry, to aid in the proper drying of dishes. 
Make sure the overfill protection float can move up and down freely. If it is locked, press down on it to release it. 

Advanced Troubleshooting 
Make sure the water inlet and drain hoses are properly connected to your Whirlpool Gold dishwasher, and the water supply is turned on. 
Check the power to the dishwasher. Make sure that a circuit breaker hasn't been flipped and that the dishwasher has power. 
Also, check to see if your water supply has the proper temperature, pressure and hardness. Whirlpool recommends the water temperature be at least 120 degrees Fahrenheit, and the pressure should be between 20 and 120 PSI to properly fill the dishwasher. If you have unusually hard water, Whirlpool recommends using a rinse aid with the high-temp option or installing a home water softener.


Dryer Troubleshooting

Does Not Run 
Step 1 
Inspect household fuses or breakers. Replace blown fuses or reset tripped breakers. The dryer is likely using two fuses or breakers. If the dryer continues to blow fuses or trip breakers, discontinue use and call an electrician. 
Step 2 
Close the dryer door firmly. The dryer will not operate if the door is ajar. 
Step 3 
Press and hold the "Start" button for five seconds. Large loads require holding the button in for a longer period of time. 

Error Codes 
Step 1 
Check the display on the dryer for error codes. 
Step 2 
Press the "Start" button and hold for several seconds to restart the dryer if "PF" appears on the display. This code indicates that a power failure occurred during a drying cycle. 
Step 3 
Call a service technician if the display shows any code that begins with the letter "E." The dryer has encountered a problem that requires servicing. 

Not Drying or Takes Too Long to Dry 
Step 1 
Clean the lint screen. Clean the screen after each load has dried. 
Step 2 
Restrict the amount of fabric softener sheets used. Use one sheet per load to avoid blocking the grille. 
Step 3 
Check the temperature of the room. The dryer requires a room temperature above 45 degrees Fahrenheit to function properly. 
Step 4 
Avoid using the "Air Only" temperature setting. Clothes will take longer to dry. Use an appropriate temperature setting for the type of clothing in the dryer. 
Step 5 
Remove some of the clothing in the dryer and dry smaller loads. Large loads cannot tumble freely and take longer to dry. 

Noises 
Step 1 
Inspect the inside of the dryer for buttons, coins or other small objects. Remove loose objects in the drum and empty all pockets before drying. 
Step 2 
Level the dryer. Turn the legs clockwise or counter-clockwise to adjust. Continue adjusting until the dryer is level. 
Step 3 
Separate clothing that is tangled. This will cause the clothing to bounce when tumbled, and the dryer will make a vibrating noise.


Furnace Troubleshooting

Furnace Not Heating 
The igniter gets very hot and glows bright orange to light the gas burner. If the igniter fails or cracks, the furnace won’t heat. To determine if the igniter is faulty, remove the igniter and inspect it for cracks. If the igniter is cracked, replace it. If the igniter is not cracked, use a multimeter to test the igniter for continuity. If the igniter does not have continuity, replace it. 

Furnace is Noisy or Loud 
The blower wheel blows air out of the furnace and through the house. The blower wheel is attached to the blower motor shaft with a set screw. If the set screw is loose, the blower wheel will wobble on the motor shaft, and the wheel will be noisy as it turns. Check the set screw to ensure that it is properly tightened. Next, inspect the wheel for damage. If the blower wheel is damaged, replace it. 

Furnace Starts Then Stops 
The flame sensor monitors the burner to detect whether or not a flame is present. If the flame sensor is defective, it might fail to detect a flame. If the flame sensor does not detect a flame, the control board will shut off voltage to the gas valve to prevent the furnace from heating. Sometimes, if the flame sensor is dirty, it will fail to detect a flame. Try cleaning the flame sensor with a fine abrasive pad. If the furnace still doesn’t heat, replace the flame sensor. 

Furnace Blower Not Running 
The blower motor blows air through the return vent, past the heat exchanger, and into the home’s venting. First, make sure that power is getting to the motor. If power is getting to the blower motor, but the motor does not run, the motor may be burned out. If the blower motor is burned out, replace it. If the blower motor hums, check the blower fan to ensure that it spins freely. If the blower fan is unobstructed but does not spin freely, replace the blower motor. 

Furnace Blower Runs All The Time 
The control board has relays that regulate the voltage to each component in the furnace. If the relay that controls the blower motor fails while it is closed, it will send continuous voltage to the blower motor, causing the motor to run continuously. If the control board is at fault, replace it.


Microwave Troubleshooting

General Troubleshooting 
Step 1 
Plug the microwave in fully. Check the household fuse or breaker box. Push thrown breakers to the "On" position or replace blown fuses, if needed. 
Step 2 
Press and hold the "Off" key for five seconds to unlock the controls if "Locked" is shown on the display. 
Step 3 
Turn off "Demo Mode" if the timer counts down rapidly when a cooking cycle is started. Press and hold the "Timer Set/Off" key for five seconds. 
Step 4 
Place 1 cup of cold water inside the microwave. Close the microwave door and set a two minute cooking cycle. Open the door and test the temperature of the water. If the water is not warm, call for service. The magnetron is not working properly. 

Turntable 
Step 1 
Start the microwave oven and watch the turntable. If the turntable does not rotate, proceed to Step 2. 
Step 2 
Place the turntable on the turntable support correctly if the turntable does not work. 
Step 3 
Remove the turntable and clean the hub, rollers and support with mild dish detergent and warm water. Rinse and dry. Replace the hub, support and turntable. 

Display Messages 
Step 1 
Reset the clock if ":" is shown on the display. Press the "Clock" key. Use the number keys to enter the correct time. Press the "Clock" key to set the time. 
Step 2 
Unlock the controls if "Locked" appears on the display and you wish to start a cooking cycle. Press and hold the "Off" key for five seconds to unlock the controls. 
Step 3 
Press the "Timer Set/Off" key two times to cancel the timer if the time is counting down on the display and the timer is no longer in use.


Range Troubleshooting

Nothing Works 
If your entire range won’t turn on, check for a power issue. Make sure the range’s power cord is plugged into an operational, grounded outlet. You can test the outlet by plugging a small appliance like a lamp into it and seeing if it turns on. If the outlet doesn’t have power, check your home’s circuit breaker or fuse box and reset the breaker or replace a blown fuse as necessary. Consult an electrician if the range still won’t turn on. 

Stovetop Doesn't Work 
If the cooktop portion of your range won’t operate, ensure that you’ve set the control knob properly. You must push the knob in to turn it to a setting. If your model has a control panel instead of knob, ensure that you’ve touched the display area on the panel to select one of the burners before choosing a function. For models with ceramic glass cooktops, verify that the Control Lockout feature hasn’t been set. This setting locks all of the controls so the cooktop won’t operate. Usually, the control panel will indicate that the setting is engaged with “LOCKED” on the display. Consult your owner’s manual to determine what pads need to be pressed to unlock the controls. 

Oven Doesn't Work 
When your range’s oven won’t operate, start your troubleshooting by verifying that the electronic oven control is set properly. Check your owner’s manual to determine the proper way to set your model’s controls when using the oven. Next, make sure that the range’s Delay Start feature, which programs the oven to turn on at a future time, hasn’t been activated. The oven also won’t operate if the Control Lockout feature has been set; check your owner’s manual to see how to unlock the controls if necessary. 

Makes Strange Noises 
You may near some noises that cause concern when your range is in operation. They are often normal operating sounds. If your range features a convection oven, you may hear a humming sound when cooking at high power. The sound should quiet or go away completely when you turn down the power. With a ceramic glass cooktop, you may hear a whirring sound during use. The cooktop has a fan that runs at various speeds to keep the electronics at a controlled temperature. It may continue to run after the cooktop is turned off, if the temperature is very high. 


Refrigerator Troubleshooting

You may be experiencing Whirlpool refrigerator problems, like the freezer isn't freezing or some other temperature control issue. The answer may be as simple as the door is ajar or the defrost timer is malfunctioning. But you may have a more complicated problem, like the refrigerator runs constantly or is noisy. The good news is you've clicked over to the right place for understanding the problem and finding the right solution.

PROBLEM: Refrigerator not cooling. 
RESULT: Condenser Coils are Dirty 
SOLUTION: The condenser coils are usually located under the refrigerator. They dissipate heat as refrigerant passes through them. If the condenser coils are dirty, they won’t dissipate the heat effectively. As debris builds up on the coils, the refrigerator becomes less efficient, causing the refrigerator to work harder to cool down. If the coils are significantly dirty, the refrigerator will not be able to maintain the proper temperature. Check the condenser coils to determine if they are dirty—if the condenser coils are dirty, clean them. 

PROBLEM: Refrigerator not cooling. 
RESULT: Condenser Fan Motor 
SOLUTION: The condenser fan motor draws air though the condenser coils and over the compressor. If the condenser fan motor is not working properly, the refrigerator won’t cool properly. To determine if the fan motor is defective, first check the fan blade for obstructions. Next, try turning the fan motor blade by hand. If the blade does not spin freely, replace the condenser fan motor. If no obstructions are present and the fan blade spins freely, use a multimeter to test the fan motor for continuity. If the condenser fan motor does not have continuity, replace it. 

PROBLEM: Refrigerator not cooling. 
RESULT: Evaporator Fan Motor 
SOLUTION: The evaporator fan motor draws air over the evaporator (cooling) coils and circulates it throughout the refrigerator and freezer compartments. Some refrigerators have more than one evaporator fan motor. On refrigerators with only one evaporator, the evaporator is located in the freezer compartment. If the evaporator fan is not working, it will not circulate the cold air to the refrigerator compartment. If this occurs, the freezer may still get cold, while the refrigerator will not get cold. To determine if the evaporator fan motor is defective, try turning the fan blade by hand. If the fan blade does not turn freely, replace the fan motor. Additionally, if the motor is unusually noisy, replace it. Finally, if the motor does not run at all, use a multimeter to test the motor windings for continuity. If the windings do not have continuity, replace the evaporator fan motor. 

PROBLEM: Refrigerator not cooling. 
RESULT: Start Relay 
SOLUTION: The start relay works in conjunction with the start winding to start the compressor. If the start relay is defective, the compressor may sometimes fail to run or may not run at all. As a result, the refrigerator will not be cold enough. To determine if the start relay is defective, use a multimeter to test it for continuity between the run and start terminal sockets. If the start relay does not have continuity between the run and start terminal sockets, replace it. In addition, if the start relay has a burnt odor, replace it. 

PROBLEM: Refrigerator not cooling. 
RESULT: Temperature Control Thermostat 
SOLUTION: The temperature control thermostat directs voltage to the compressor, evaporator fan motor, and condenser fan motor (if applicable). If the temperature control thermostat is not working properly, it may prevent the refrigerant system from running. To determine if the thermostat is defective, rotate the thermostat from the lowest setting to the highest setting and listen for a click. If the thermostat clicks, it is not likely defective. If the thermostat does not click, use a multimeter to test the thermostat for continuity. If the temperature control thermostat does not have continuity at any setting, replace it. 

PROBLEM: Refrigerator not cooling. 
RESULT: Start Capacitor 
SOLUTION: The start capacitor provides a boost of power to the compressor during start-up. If the start capacitor isn’t working, the compressor may not start. As a result, the refrigerator will not cool. To determine if the start capacitor is defective, test it with a multimeter. If the start capacitor is defective, replace it. 

PROBLEM: Refrigerator not cooling. 
RESULT: Temperature Control Board 
SOLUTION: The temperature control board provides voltage to the compressor and fan motors. If the temperature control board is defective, it will stop sending voltage to the cooling system. However, this is not a common occurrence. Control boards are often misdiagnosed—before replacing the control board, first test all of the more commonly defective components. If none of the other components are defective, consider replacing the temperature control board. 

PROBLEM: Refrigerator not cooling. 
RESULT: Thermistor 
SOLUTION: The thermistor monitors the refrigerator temperature and sends the temperature reading to the control board. The control board regulates power to the compressor and evaporator fan based on the thermistor readings. If the thermistor is defective, the compressor and evaporator fan may not run when necessary. As a result, the refrigerator will not be cold enough. To determine if the thermistor is defective, test it with a multimeter. The thermistor resistance should change in conjunction with the refrigerator temperature. If the thermistor resistance does not change, or the thermistor does not have continuity, replace the thermistor. 

PROBLEM: Refrigerator not cooling. 
RESULT: Compressor 
SOLUTION: The compressor is a pump which compresses the refrigerant and circulates the refrigerant through the evaporator and condenser coils. If the compressor is not working, the refrigerator won’t cool. However, this is rarely the case. Before replacing the compressor, first check all of the more commonly defective parts. If you have determined that all of the other components are working properly, check the compressor. Use a multimeter to test the continuity between the electrical pins on the side of the compressor. If there is an open circuit, the compressor is likely defective. If the compressor is defective, it must be replaced by a licensed technician. 

PROBLEM: Refrigerator not cooling. 
RESULT: Main Control Board 
SOLUTION: The main control board might be defective. However, this is almost never the cause. Before replacing the main control board, test all of more commonly defective parts. If none of the other components are defective, consider replacing the main control board. 
 


Washer Troubleshooting

Duet Washer Won't Turn On 
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. 
Attempt a Duet Washer Quick Diagnostic Test 
Check the power supply at the wall with some other device. If the wall plug has power... 
Check the Duet Line power filter 
Check power at the control. 

Duet Washer Won't Start 
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. 
Attempt a Duet Washer Quick Diagnostic Test 
Does The Washer Have Power?  

Duet Washer's Door Won't Lock 
Duet Washer Wont Unlock 
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. 
Attempt a Duet Washer Quick Diagnostic Test 
Check the Duet door lock. (Duet Door Lock Check) 

Duet Washer's Door Won't Unlock 
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. 
Attempt a Duet Washer Quick Diagnostic Test 
You can manually unlock the washer by removing the top (remove screws on the back of the top panel and slide the top panel back to lift off. then with the washer unplugged reach down and pull a small ring on the top of the door lock to manually open the door lock. 
Check the Duet door lock (Duet Door Lock Check) 

Duet Washer Wont Fill fish 
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. 
Check your home water valves 
if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test. 
Check the Duet water valves (Duet Washer Valve Check) 

Duet Washer's Drum Won't Rotate 
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. 
Attempt a Duet Washer Quick Diagnostic Test 
Check the Duet Motor and motor control unit (Duet Motor Check) 

Duet Washer Leaking 
The most common cause of a Duet washer leaking is a hole in the washers door boot / bellows. However, a leak can come from many of the washer's parts. the best way is to narrow your problem down, is it leaking all the time, even when the washer is off? (valve or water supply) or only when the washer is running? (hose, drain pump, door boot / bellows) Visually inspect the washer for the source of the leak, be careful of moving parts that may remove your parts! 

Duet Washer Vibration 
Make sure your Duet washer is on solid footing… can you rock the washer by pressing on one of the corners.(adjust the washer legs) 
Does the washer go out of balance EMPTY during a Duet Washer Quick Diagnostic Test? No => What if you have a heavy load of like items (all towels) on a short normal cycle? If it can balance an all towel load, your problem is probably load related. (Read the users manual) If it is off balance empty or the all towel load went off balance move to step #3. 
Press down on the inner drum and feel for a popping movement (The inner drum support may be broken… this is bad) Try rotating the drum a few degrees and try several times… the inner and outer drums should move together as a unit. Sometimes the three point support that suspends the inner drum inside the outer drum can crack. If there is movement you may need a new inner wash drum. 
Unplug the washer and remove the back panel to check the tub shocks. They should all be attached. 
If all that checks out your probably safe to replace the washer's shocks. 

Duet Washer Not Cleaning Well 
Duet Washing Machine Cleaner 
Your washer can get extremely nasty inside in places you can't see. Try leaving the door open a crack when the washer is not in use and make sure to use the Clean washer cycle from time to time. Run a Duet Washer Quick Diagnostic Test and make sure that the washer is mechanically working correctly. If it is then you may want to try a different detergent.


Water Heater Troubleshooting

Step 1 
Check for leaks from the tank. There is no fix for a water heater with a leaking tank. It must be replaced. 

Step 2 
Check the breaker to be sure power is on for the water heater. It is necessary to check the working condition of a water heater with power supplied to the unit. Put on rubber sole work shoes and be sure the floor near the tank is completely dry. 

Step 3 
Unscrew the cover plates on the upper and lower access panels with a Phillips head screwdriver. Put on work gloves to remove the insulation cut-outs. 

Step 4 
Check the limiter switch. Some problems will cause the heat limit switch to trip and cut power to the unit. Press the "Reset" button to restore power. Continue testing to find the problem that tripped the switch. 

Step 5 
Troubleshoot water heaters that put out cold water. Check the power running to the upper element. If the voltage tester shows power, but the element is not heating, then the element is bad. If there is no power coming to the element, then the thermostat has failed and must be replaced. 

Step 6 
Troubleshoot water heaters giving warm water or small amounts of hot water. Check the temperature setting. Adjust the setting with a slotted screwdriver if necessary. Set the temperature between 110 and 125 degrees F. Check the cold intake tube and fastener ring. If cold water is pouring into the upper tank it reduces the output temperature. Make sure both thermostats are pressed firmly against the tank. Check the power at the upper thermostat connection terminals that transfer power to the lower thermostat. If the tester shows no power at these terminals, then the upper thermostat is faulty. If power registers, then test the terminals at the lower element. If no power shows, the lower thermostat has failed. If there is power but no heat at either element, then that element is bad. 

Step 7 
Troubleshoot a water heater that puts out overly hot water. Check the temperature set screw. It should not be set above 125 degrees F. If the temperature is properly set, then one of the thermostats is to blame. Check for power at both elements. Any element that is getting power while the water is too hot has a faulty thermostat. 

Step 8 
Correct the problem of popping sounds. Elements that have mineral build-up make popping sounds when they are working. Drain the tank and shut off power and water supply to the unit before removing an element to clean or replace it. 

Step 9 
Get rid of bad odors in hot water. Magnesium anode rods cause bad smells when exposed to some of the minerals common in tap water. Drain the tank, shut off the power and water supply and clean the tank thoroughly with bleach water. Replace the anode rod with one made of aluminum.



Whirlpool Appliance Troubleshooting

Whirlpool appliance problems

Whirlpool appliance broken

Whirlpool appliance issue

Whirlpool appliance difficulty


Product Reviews:

Whirlpool Cabrio Washer WTW6200VWO & Cabrio Dryer WED6200SW1 - My Cabri
Whirlpool Cabrio Washer WTW6200VWO & Cabrio Dryer WED6200SW1 - My Cabrio washer ties clothes in knots but the big issue is that if it goes to UL (uneven load). There is no alarm. Washer stops all operations except one. It fills up over the top, all over the rec room, out the door and down the street until someone alerts me! I run down, hit cancel and it drains. I unknot the clothes and start over. Then I mop up! Help! My Cabrio dryer has been through four door latches and I finally realize that the issue is that the latch and the protruding part do not line up evenly. This breaks the latches. Help!
Published: February 4, 2013
Mary Ann of Woodstock, CT
Source: consumeraffairs.com

We moved to a new house Nov. of 2012 and I went to Lowes to buy a new refri
We moved to a new house Nov. of 2012 and I went to Lowes to buy a new refrigerator. The last refrigerator we bought was a Maytag. It was a LEMON and probably had every part replaced because we had the warranty. At Lowes I thought the Whirlpool Refrigerator would be a good choice. We didnt purchase the warranty, big mistake. After only 4 YEARS, the refrigerator is DEAD, not in working order and would too expensive to fix says our reliable repair serviceman.
Published: November 2, 2016
Jo of Buda, TX
Source: consumeraffairs.com

We purchased a higher end cabrio model only 3 years ago. Last year, on abou
We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.
Published: November 18, 2014
Brian of Thunder Bay, ON
Source: consumeraffairs.com

Burners always needed replacing and now do not work anymore - Whirlpool ran
Burners always needed replacing and now do not work anymore - Whirlpool range looks nice, but very expensive to maintain. The burners constantly needed replacing, they do not heat up. I got a repair technician to look at it. He replaced the parts that the burners hook into. Now they do not heat up at all. Well, one of four barely boils water. The oven still works, oh great. The thing is only 7 years old. I have had ovens that lasted 20+ years at my dads house or 15 years at another house I lived in. With all the negative comments and the repair guy who tried to fix it, I think it is time to get the kids Easy-Bake Ovens out of the storage or buy a new range. Obviously, it will not be a Whirlpool. So many negative comments people left, my useless top burners seem mild comparatively.
Published: February 22, 2012
Nancy of Monroe, NC
Source: consumeraffairs.com

I owned a Kenmore washer for approx. 20 yrs that endured 6 kids for most of
I owned a Kenmore washer for approx. 20 yrs that endured 6 kids for most of that time period. When time came for a new one, I had to have the latest model, and settled on a Maytag Bravos approx 3 yrs ago. This was a huge mistake - I paid between 600-800 for this machine, and it is a piece of garbage. The repairmen here yesterday explained to me that Maytag and Whirlpool are now the same company, and also that all these machines are now made overseas because of cheap labor. In a nutshell, I was given an estimate of at least 300 to repair this piece of crap - he explained that they are only made to last a few yrs -where is the justice in this situation? I really dont get how these big companies get away with selling crap, knowing all the while that the consumer is getting screwed - yet people continue to buy them..
Published: April 14, 2016
catherine of Lex, SC
Source: consumeraffairs.com

Purchased Whirlpool Cabrio model WTW6400SW washer and dryer 1/7/2007. The m
Purchased Whirlpool Cabrio model WTW6400SW washer and dryer 1/7/2007. The matching dryer was dead on arrival and the second dryer motor died within a year. Washer: 1year 2 month the washer motor died. Whirlpool paid for the part and I paid the labor. The following year, the bearing went out and the outer tub was replaced (the bearing is inside the plastic outer tub - bad design. Whirlpool paid for the part and I paid the labor. Feb. 2011 had one of the F errors. Whirlpool repair tech came out as the tub would not drain and it was a wire that had come loose underneath washer - another service call charge. Dec. 20, 2011, I had an error F50. The Whirlpool repair tech came out, verified no clothes or money stuck in the machine. All clear. He called higher level whirlpool tech and they paid parts and labor to replace the main control board and the RPS Sensor. Im single and am not abusing this machine. Like everyone else who posted. I paid close to $1,000 for this washer (not including the dryer) and I have been a faithful Whirlpool customer for 3 generations, but if Whirlpool doesnt offer some kind of compensation/trade in credit to customers who purchased this (knowing that the design is bad/faulty) washer and discontinue this model. This will be my last Whirlpool. I will have lost all faith in Whirlpool. The Whirlpool service tech that I found is op notch. I will miss him if I have to switch brands. Im putting 1 star as I know this machine will not be operational for 9 years which is the minimum that I would expect. If it makes it to 6 years without another service call, it will be a miracle.
Published: December 21, 2011
Kimber of Salem, VA
Source: consumeraffairs.com

I purchased at Lowes and they say was without warranty. I have had all kind
I purchased at Lowes and they say was without warranty. I have had all kinds of trouble. The pilot light was replaced in the burner easily because of recall. Now the pilot will not stay lighted unless you tap on the gas valve. Then as soon as the water temperature comes up, the burner and the pilot light go out. I went to Lowes for a new gas valve. They have one for natural gas of $58. They do not stock for propane. I have to purchase from Whirlpool which costs $228. Their comment is that it is more expensive to build another. They do not change offices any longer because of PSi difference bull crap. I purchased a Whirlpool gas stove 2 to 3 years ago and I had to purchase an LP change over kit to use it. This is nothing but a case price extortion. I will never purchase another Whirlpool product again and I would advise no one else either!
Published: December 23, 2011
Edward of Clark, MO
Source: consumeraffairs.com

Whirlpool Gold Series - I bought this dishwasher less than 2.5 years ago. T
Whirlpool Gold Series - I bought this dishwasher less than 2.5 years ago. The thing already broke. The motor needs to be replaced at a cost of about $250. The thing never did a good job anyway and often had to run it more than once to get dishes clean. I paid about $650 for the machine so I guess its just a throw-away appliance. Whirlpool makes complete junk. I will buy a different brand that is known to have long-lasting dishwashers. I guess you get what you pay for.
Published: November 9, 2015
Dave of Toronto, ON
Source: consumeraffairs.com

We purchased a Whirlpool washer/dryer set 19 months ago and the washer just
We purchased a Whirlpool washer/dryer set 19 months ago and the washer just stopped working. Our trusted fix-it man came out and diagnosed it as a spin bearing problem assuring me it was not anything we had done. He stated it was a defected part or Whirlpool had never put grease in the bearings. A 450.00 part not counting diagnosis and labor. When I called Whirlpool, the first response I got was that they were sorry but we didnt buy the extended warranty, and of course the warranty it had was only a year. I asked to talked to a supervisor and finally she agreed to supply the part, but I was still responsible for the diagnostic and labor fee, which will be a couple of hundreds of dollars! Not happy with Whirlpool and will NEVER buy any product with their name again. Beware consumers!!!
Published: October 13, 2014
Pam of St Joseph, MO
Source: consumeraffairs.com

This washer has no agitator. Drum will shake back and forth while load of c
This washer has no agitator. Drum will shake back and forth while load of clothes will stay in the same place sliding towards the opposite direction of the movement for 20 minutes. Clothes are not turning, no going up or down, just staying still and not getting washed as expected. Baseball cap and construction worker jeans didn’t washed as it should have been.
Published: January 22, 2020
J. B. of Miami, FL
Source: consumeraffairs.com

I have purchased a Whirlpool refrigerator and it has passed only 1.5 years
I have purchased a Whirlpool refrigerator and it has passed only 1.5 years and I have repaired it twice. The cost of repairing is also very high. Service charge is very high so I called a local party to solve the issue. They checked and found that a capacitor and a compressor relay is not working. They replaced the two and debited a cost of Rs.1500.
Published: March 11, 2012
Sudarsh of Pune-411019., OTHER
Source: consumeraffairs.com

I have a refrigerator model WRT359SFYM00 that is 4 months old. It suddenly
I have a refrigerator model WRT359SFYM00 that is 4 months old. It suddenly just stopped getting cold. Trying to contact Whirlpool warranty/service department has been a nightmare. Once I did get them they spent almost a week trying to locate someone in my area to service it. I was in constant contact with the phone support person, but they kept telling me its out of my hands a special unit was making calls to find a repair person. After almost a week they informed me they could not find anyone but if I could find someone to service it they would reimburse me (max $250 labor). I spent 5 minutes and 1 phone call and I found someone.They wasted a week bumbling around with wanton disregard for their customer. Their service after the sale is deplorable. They are staffed by people who answer calls but have no ability or authority to fix a problem. Worse yet, they kept telling me it was out of their hands. If not in their hands, then whose? I assure you I will never buy another Whirlpool appliance simply based on this warranty experience. What a horrible way to treat your customers. Shame on Whirlpool!
Published: May 22, 2015
Thomas of Pioneer, CA
Source: consumeraffairs.com

A couple of years ago, we had 2 natural gas hot water heaters installed. We
A couple of years ago, we had 2 natural gas hot water heaters installed. We immediately had a service call to replace the thermostat on one of them. Then recently, the other one had to be replaced because of the leaky tank. It was still in warranty, and we had to pay $425 for the old one to be removed and the new one installed. Now, this one has a bad thermostat and the A & E Factory Service is coming tomorrow to install the new thermostat. We have been inconvenienced by this for a couple of weeks as we have no hot water in the master bath. We were just lucky that we had one hot water heater working in the other part of the house. I think that Whirlpool should have paid the $425 for the installation as the original hot water heater was in warranty. Now, I hope that tomorrows visit will be covered by the warranty. Next time we need an appliance, we will not be purchasing a Whirlpool.
Published: January 15, 2013
Elsie of Montgomery, TX
Source: consumeraffairs.com

IM single, and my current refrigerator meets my basic needs quite well. One
IM single, and my current refrigerator meets my basic needs quite well. One drawback -- it has an ice making machine which I never use. Therefore, that takes up room in the freezer which could be used for frozen foods.
Published: January 12, 2017
Louis of Aurora, CO
Source: consumeraffairs.com

Whirlpool side by side model WR5571CIDM. Unit rattles EVERY time refrigerat
Whirlpool side by side model WR5571CIDM. Unit rattles EVERY time refrigerator is opened or closed + plus every hour or so spontaneously. Rattle seems to come from the water filter area. Whirlpool serviceman says its normal for this model and calls to Whirlpool customer service say just live with it. Hard to believe Whirlpool considers this acceptable performance in a new model.
Published: October 25, 2017
Bart of Pasadena, CA
Source: consumeraffairs.com

Immediately after install, the oven door face kept coming loose, they did s
Immediately after install, the oven door face kept coming loose, they did send someone to fix & replace. Ive used the self cleaning twice, first time was fine, second time not so much. The cleaning process left major scrum below the window inside the door & below, which wasnt there before I did the clean. I take great pride in keeping my oven clean, do not allow build up because then you cant get it clean. This stove is less than a year old & has only been in place for 6 1/2 mths (I purchased before remodeling was complete).My last stove I sold easily, it was clean & guess what. It was 32 years old, only replaced because of updating our kitchen!!! I contacted whirlpool & they said its cosmetic & not covered. I called Lowes, they refer me to the service advance phone #. Well that was Whirlpool, not Lowes. Still nothing being done, other than they sent me cleaning stuff to try and get it cleaned (still working on that). Im concerned this stove is going to continue to have issues & will be out of warranty soon. Whirlpool is not standing behind their products & we have been Whirlpool customers for a long time. If I have more issues with this stove, we will never purchase Whirlpool again. Dont buy their products, they dont stand behind them!
Published: October 16, 2019
Keith of New Haven, IN
Source: consumeraffairs.com

Whirlpools front load washers do not have easy access to the drain pump fil
Whirlpools front load washers do not have easy access to the drain pump filter. The entire front of the machine including the door has to be taken off to access the filter. When putting washer back together the parts are cheap and screws break. Most companies that sell front load washers provide easy access to the drain pump filter. Buy one of those instead of a Whirlpool and you will save yourself a lot of time and hassle.
Published: November 12, 2017
Nikki of Bozeman, MT
Source: consumeraffairs.com

My experiences using Whirpool ranges and ovens have been very positive. As
My experiences using Whirpool ranges and ovens have been very positive. As a matter of fact, that is the brand preferred by my family through several generations. Durability, reliability and warranties have been the main features we have found useful. Most of the ranges and ovens have been replaced at home, always with Whirlpool brand, but with added improvements that manufacturer come up with, in order to integrate our devices to the latest technologies. I would recommend this brand to the readers, friends and neighbors.
Published: February 13, 2021
Mauricio of Harlingen, TX
Source: consumeraffairs.com

Whirlpool Cabrio HE washing machine - I was very excited when buying this p
Whirlpool Cabrio HE washing machine - I was very excited when buying this product. It never really washed clothes thoroughly. I kept getting strange stains on them and even after emptying it as soon as it finally was able to finish a load without saying UL constantly... the clothes would stink. Im sick I ever bought it! Plus, it rusts terrible.
Published: August 25, 2015
Lindsay of Roscoe, IL
Source: consumeraffairs.com

This is a replacement of a similar model, that lasted 23 years. This modest
This is a replacement of a similar model, that lasted 23 years. This modest, white, 2 door, side by side refrigerator, was purchased without the optional ice maker. It was bought specifically for the dimensions, of our custom cabinets. There are obvious differences, from the previous incarnation. The textured doors were replaced with a smooth glossy finish and their height extends higher than the refrigerator cabinet. The adjustable shelves were replaced with less adjustable pre fixed shelf supports. The LED interior lighting is much brighter that the incandescent bulbs they replaced. Overall, so far a very capable refrigerator, for a moderately sized kitchen and if the life, lasts as long as the one it replaced, this was a very good purchase.
Published: February 15, 2021
Bernard of Bronx, NY
Source: consumeraffairs.com

I have a Whirlpool built-in double oven. It is 7 years old. The top oven ha
I have a Whirlpool built-in double oven. It is 7 years old. The top oven has overheated 3 times with food in it and it locks the door. The oven beeps and says, Too hot, and locks the door. Luckily I was in the kitchen when it overheated, so I could turn the oven off. After turning the oven off, the oven has to cool off before the door will unlock and the food can be taken out. By then, the food is really burnt.I called Whirlpool to see if there is a recall and they said, No recall, and the oven was out of warranty. So I called the repair shop. They said it was the control board and they were not sure they could get a new control board. I may have to find someone that can rebuild this control board. They said not to use the oven. It could cause a fire. I would think that they should recall these ovens. They should have a safety switch that shuts the oven off if it overheats like mine has done.
Published: August 30, 2016
Debbie of Minneapolis, KS
Source: consumeraffairs.com

Cabrio washer Model # wtw5840bw - I purchased this washer one year ago. It
Cabrio washer Model # wtw5840bw - I purchased this washer one year ago. It has a defect that comes along with it. You think your clothes are getting clean. But in reality they are not. This washer does not fill enough water to wash a small load of clothes. It has ruined three large bags of my clothes. Stained they smell in general they are not clean. Worst washer I have ever bought. General public Please be aware of this issue if you are going to purchase this washer. It is a big expense to be put out to the curb.
Published: April 22, 2015
lori of Pilot Point, TX
Source: consumeraffairs.com

We came home from work and all was well. About an hour later, there was a s
We came home from work and all was well. About an hour later, there was a strong burning smell in the kitchen, like wires burning. Sourced it to our refrigerator. Brought our grandson upstairs to the second floor apartment to get him away from the smell and possible smoke and/or fire. This unit has been repaired several times but not recently. After reading all the same reviews on this problem, we are definitely concerned that a fire may arise. Unfortunately we may wind up buying another, very expensive, refrigerator in the very near future but it will definitely not be a Whirlpool. I wish I could give Whirlpool a ZERO star because that is even too good for this company.
Published: September 20, 2016
Mary Lynn of Elmwood Park, NJ
Source: consumeraffairs.com

Whirlpool Gas Range WFG540H0es - Purchased 2 months ago. After 2 weeks ther
Whirlpool Gas Range WFG540H0es - Purchased 2 months ago. After 2 weeks there was a spill. The black burner caps are powder coated. After cooling we washed it with dish detergent & a sponge. The powder coating came off. Called the company. They replaced burner caps. Last week there was a spill and it stained the burner bases which are powder coated in a silver color. We tried 409 cleaner, Windex, dish detergent with a sponge. Could NOT get the stain out started removing powder coating. Called the company they ONLY guarantee cosmetic appearance 30 days. They wanted $139.00 for a new set of burner bases. I am going to go back to Lowes & see if we can return this Whirlpool range.
Published: November 10, 2016
Arnold of Lawrenceville, GA
Source: consumeraffairs.com

Whirlpool gold series refrigerator leaks water from freezer after 14 months
Whirlpool gold series refrigerator leaks water from freezer after 14 months because ice builds up causing the door not to shut properly and rime ice forms over food. I called Whirlpool and theyve not heard this problem before and stated I should have gotten the extended warranty. This is ridiculous. The internet is flooded with people having the same problem.
Published: June 24, 2013
Peter of Lynn, MA
Source: consumeraffairs.com

Purchase a brand new Whirlpool fridge at the Fry’s Electronic in 2017. Br
Purchase a brand new Whirlpool fridge at the Fry’s Electronic in 2017. Broke down in 2018 almost 1 year after. Called Whirlpool company for replacing a new one. They didn’t replace before they had sent out a certified technician for fixing 3 times. It took forever to fix it, and still had the same problem after months. Finally, they agreed to replace a new one. Now I still have the same problem with a newer one which they replaced it over a year ago (including fixing and placing time). Just called to the Whirlpool company today for fixing or replacing, spoke to rep Sara, she said that it’s no longer under warranty because it’s more than 1 year. I told her that because the company didn’t replace right away; therefore, it has been more than 1 year; but from the time they replaced it, it hasn’t been 1 year. Ill never buy any Whirlpool products again.
Published: April 1, 2019
Chau of Garden Grove, CA
Source: consumeraffairs.com

I purchased this Whirlpool washing machine in July 2009. The repairman just
I purchased this Whirlpool washing machine in July 2009. The repairman just gave us a $1400 estimate for repairs due to failure of bearings. This is an energy efficient, expensive appliance that we expected to last for years and we feel that 2 1/2 years of service is unacceptable. We did not purchase an extended warranty and Whirlpool said they would help with the cost of parts - not labor. We cannot afford to repair a lemon and so purchased an LG front-loading washing machine today. Hopefully we will have a better experience with LG as we will not be purchasing any more Whirlpool appliances ever.
Published: February 25, 2012
Julia of Noblesville, IN
Source: consumeraffairs.com

If I fix this washer I will have been on 3 motherboards in the 5 years I ha
If I fix this washer I will have been on 3 motherboards in the 5 years I have owned this machine. That is inexcusable and indicative of crap quality control and manufacturing process. I should not have to replace the control board at these intervals or, within 5 years, at all. I will never touch another Whirlpool appliance again.
Published: November 18, 2016
John of Batavia, OH
Source: consumeraffairs.com

Weve been in our new home less than a year and a half and our brand new Whi
Weve been in our new home less than a year and a half and our brand new Whirlpool French door fridge is dead. Service is a week away. Updates to follow.
Published: August 18, 2015
Kenny of Fairdale, KY
Source: consumeraffairs.com

Contacted Whirlpool - unit (Cabrio washer 7600xt) is out of 12-mo warranty.
Contacted Whirlpool - unit (Cabrio washer 7600xt) is out of 12-mo warranty. Spoke with manager, Tracy **. She said they would not help - out of warranty. Called local parts/service center - ea. hinge is $42 plus shipping and labor to install. Obviously this is a defective design. The lid is too heavy. I was having a difficult time deciding to spend 150-200 dollars every 2-3 years for hinges on a $700 washer and then I read all the other complaints about Whirlpool washers. I will sell it for scrap and buy a better brand.
Published: May 21, 2014
dennis of Tampa, FL
Source: consumeraffairs.com

What a POS. Havent even used the thing to cook a meal yet and already some
What a POS. Havent even used the thing to cook a meal yet and already some chunk of metal fell out from the port at the top left inside the oven (behind the vent). It was clearly cheap pot metal. What else is this thing made out of?
Published: November 29, 2014
Jims of Arlington, MA
Source: consumeraffairs.com

Purchased this washer in 2009 from Lowes, believing the hype that it was ef
Purchased this washer in 2009 from Lowes, believing the hype that it was efficient. Since we only needed a Washer at the time, we overpaid (it is more cost effective when you buy both washer and dryer). So we paid $1000.00 for this machine (we purchased the stand as well). After the 1st year, there seemed to be a significant decrease in how fast the washer spun, as the clothes were coming out wetter. I didnt pay much attention, but 2 years later, the machine has a weird problem where it couldnt complete the cycle, and by this time, every time it Spun, the noise was louder and louder.I contact Whirlpool, placed a service call and the Technician came out. $225.00 later, there was a hose that was pinched that was sending a wrong signal to the washer. He fixed that and told me I should get a contract on the machine through Whirlpool since I seemed to be having problems. I purchased the contract, for $300.00, and 2 1/2 weeks later placed another service call, as the noise from the machine was happening every time I did laundry. The service guy came out, indicated that it seemed to be the Agitator, and that he would need to order parts, and that they had a SPECIALIST who only does this type of repair, since they have many! He also indicated that the hose may have crimped due to the movement of the entire agitator!Well, after not hearing from ANYONE for 2 weeks, I called the repair company who told me WHIRLPOOL was supposed to call and let me know that they would NOT fix the machine, as the parts cost more than the Washer, which is now valued at $500.00! No one from WHIRLPOOL EVER CALLED, and I cant understand how a $1000.00 Washing machine touted to be so efficient and environmentally friendly has been THROWN OUT after 3 years!!! And now I am out the $225.00 repair, have no washing machine, $1000.00 down the drain (and I forgot to mention a year later we bought the matching WHIRLPOOL DRYER and OVERPAID) and now have to purchase another machine, which I assure you WONT BE WHIRLPOOL! As most of us have experienced, WASHING MACHINES last for many years! The washer I had before this was over 20 years!!!! So much for efficient and environmentally friendly... The only thing GREEN about this machine is how much of my $$$ has gone to Whirlpool!
Published: October 25, 2013
Patti of Pompton Plains, NJ
Source: consumeraffairs.com

Quiet running, does a great job cleaning and drying the dishes, experienced
Quiet running, does a great job cleaning and drying the dishes, experienced some cloudiness on the glassware but found that if I position them in the middle of the upper rack that issue was solved.
Published: January 23, 2018
Palma of Eldersburg, MD
Source: consumeraffairs.com

I bought a Whirlpool gold side by side with freezer on bottom and the ice m
I bought a Whirlpool gold side by side with freezer on bottom and the ice maker in refrigerator part in March of 2013. Ice maker dropped ice one time. In 5 days Lowes brought me a new one out and swapped it because it was in their 7 day policy. Ok this one worked good for about 2 months. Ice maker quit again. Service came out, changed out some parts that didnt work. 2 months roll by the new parts they ordered came in. Service came out again, put those parts in. Worked for about 3 weeks then stopped again. 3 times new service guy comes out and replaces some more parts and he had the wrong motherboard so guess what, had to order. It took 4 weeks to get it here. They came, put it on. It worked for around 2 months. I asked Whirlpool for my money back, they said that that was not a going to happen. I asked for another refrig, they said they would have to have 3 more service calls on the frig before they could do that. Well I have got a $3000 dollar refrigerator that has no working ice maker and Im sick and tired of the runaround. Whirlpool sucks. I will never buy another thing with their name on it. Matter fact I wouldnt take it if you give it to me. (Why) you ask, because in a short time Im going to have to haul it off for junk and its not going to bring nowhere near what I gave for it at the scrap yard.
Published: September 22, 2014
Mitchell of Comer, GA
Source: consumeraffairs.com

We bought a Whirlpool oven in Costa Rica. Wanted a good oven from a reputab
We bought a Whirlpool oven in Costa Rica. Wanted a good oven from a reputable manufacturer. Oven has had numerous problems over the past 2 months. Local vendor is worthless and trying to run out guarantee time. Whirlpool U.S.A. says it will not help with problems for products sold outside US or Canada. Fair enough. THEN DO NOT SELL THE WHIRLPOOL BRAND WHERE YOU DO NOT SUPPORT YOUR PRODUCT.
Published: August 27, 2014
David of Puerto Viejo, Other
Source: consumeraffairs.com

I opened the door of my Whirlpool oven purchased last year and pulled out t
I opened the door of my Whirlpool oven purchased last year and pulled out the rack to remove my food and the rack completely tilted towards me causing the food to fly out of the pan into the oven bed with juice and barbecue sauce falling between the storage bin and the floor. This could have easily poured out on me. The rack support is not strong enough to support the weight of the food pan.
Published: October 17, 2014
Deana of Durham, NC
Source: consumeraffairs.com

We purchased a Whirlpool Cabrio model # WTW6400SW3 in 04/08. Approx. 6 mont
We purchased a Whirlpool Cabrio model # WTW6400SW3 in 04/08. Approx. 6 months ago, the washer started to be un-level during the spin cycle. This has progressively become worse, it now becomes un-level during the rinse cycle. We spoke with the appliance store where we purchased it, ;hey said the repairs could cost $400 or more. Thats nearly half of what it cost new. Like other complaints Ive read, cheaper washers have lasted years longer than the Whirlpool. Our last washer, a Kenmore, lasted 15 years.
Published: January 7, 2012
Doug of Waller, TX
Source: consumeraffairs.com

Whirlpool Cabrio Top Load Washer Model: WTW7800XWO purchased at Lowes 8/26/
Whirlpool Cabrio Top Load Washer Model: WTW7800XWO purchased at Lowes 8/26/2010. The lid was broken at the hinge in less than a year and was replaced under factory warranty. Lid falls down and pinches fingers. The second lid broke in the same location in less than a year. Lid falls down and strikes the eye. I’m speaking with repair technicians and researching complaints on this product. It appears to be a design defect that is not being addressed by the manufacturer.
Published: July 19, 2012
Gary of Woodhaven, MI
Source: consumeraffairs.com

We will never, I repeat, never buy another Whirlpool, Kitchen Aid or Maytag
We will never, I repeat, never buy another Whirlpool, Kitchen Aid or Maytag (other than the Maytag dishwasher) product again. After just two years on the Cabrio washing machine, the bearing on the wash tub began to go out. As it was out of warranty, the cost to fix was greater than just buying a new machine. This was a known problem and Whirlpool failed to remedy the problem. Based on this experience, we went with an LG as a replacement. Before you buy anything, research it.
Published: September 7, 2013
Keith of Seabrook, TX
Source: consumeraffairs.com

After reading all of these reviews, Im not surprised at the negative commen
After reading all of these reviews, Im not surprised at the negative comments. My husband and I owned a Whirlpool washer and dryer for 25 years prior to them both dying the same summer four years ago. I absolutely would not purchase anything but another set of Whirlpool washer and dryer because of the longevity of our previous set.We bought the Cabrio set 4 years ago this summer. After two years, we discovered it had a slow leak at the back hot water valve and underneath it somewhere when it spun and it had slowly leaked under the wall into our living room which eventually caused our hardwood floors to buckle. We had to replace the flooring in that section at a cost I will not even say and had a repairman come out and fix the lid lock, leak where for some reason there wasnt a washer in the valve area, underneath and the problem with the spin cycle. This was at a cost of around $200.00. Of course our one year warranty had run out. The next year it did the SAME THING AGAIN!!! Although we caught it quicker, we STILL had to replace a small section of hardwood flooring and have the machine repaired yet again at the tune of approximately $200.00. Now, as I type, our machine has yet again flooded our laundry room one year later and I will have to call a repairman in the morning yet again! Its becoming an annual and costly thing!!!I came across this site while looking to see if by chance this machine had been recalled and we would be able to get another one at no cost since we have already paid a fortune for the errors it has caused. I will be reporting to the Better Business Bureau and writing YET ANOTHER letter to the Whirlpool company with the hopes that they will recall this machine!! If enough people protest and report this shoddy workmanship, maybe they will!!!
Published: July 10, 2014
PL of Mount Airy, NC
Source: consumeraffairs.com

The unit had all the features that we wanted and considered essential. The
The unit had all the features that we wanted and considered essential. The unit only weak issues is temperature(s) in both sections. The freezer is very poor with ice build up on the food stored for more than a couple of days. The manufacturer has been very weak in support as to how to solve this problem.
Published: August 23, 2020
Paul of Silver Spring, MD
Source: consumeraffairs.com

In 2013, my husband purchased a Whirlpool Hot Water Heater model #E2F40RD04
In 2013, my husband purchased a Whirlpool Hot Water Heater model #E2F40RD045V 40 gal. from Lowes in Vancouver, WA. On 12/12/15, had to call a plumber, the hot water heater was intermittent hot/cold. He flushed it, checked all power connections and changed the elements. On 3/18/16, NO hot water. Having a 6 year warranty, I called Whirlpool. They gave all kinds of excuses and told me to try a bunch of tests. By the time I got back to call them they were closed. I called them again on Monday 3/21/16 and said nothing worked and it had popped the breaker. They said change the elements. I told them I had just changed the elements 3 months before. I told them it was faulty wiring. They said the top element must be faulty. I gave up at that point and called the plumber. He came right out the next day. I had purchased a Rheem hot water heater to install and asked him to check the Whirlpool hot water heater elements he installed before he removed it. That is when it was discovered that under the insulation around the bottom element it was all scorched from FAULTY wiring. I called Whirlpool again and told them I could send them a picture and they said dont bother and immediately gave me an RA to return the hot water heater to Lowes. I told them I had already purchased another hot water heater and it was not a Whirlpool. I am going to request a refund.
Published: March 23, 2016
Deanna of Curlew, WA
Source: consumeraffairs.com

Just about three years old our washing machine started making a horrible no
Just about three years old our washing machine started making a horrible noise and soon after a horrible smell. Won’t complete spin and dry. The bearing inside the drum has failed. The pump is making an unusual noise. I see a lot of reviews about this product. I find it strange that it appears to have a good rating at all the advertisers but in reality it’s really a horrible machine. Shame on Whirlpool for our landfills, dumps and recycle bins with absolute garbage plastic and metal Has to be recycled. We have only disposable garbage for appliances.
Published: April 10, 2019
Randy of Chatsworth, CA
Source: consumeraffairs.com

I have always liked Whirlpool products but it seems lately they are lagging
I have always liked Whirlpool products but it seems lately they are lagging in this department. My washer/dryer combo each separate I dont feel are doing the job they should be. Washer is the bigger problem. Softner dispenser not distributing the softner correctly and now I have to clean out after each use. These are about 10 years old now. Is not spinning all the water out and not at all sure if clothes are getting clean. Most of their products usually lasted much longer back a few years.
Published: March 28, 2019
Sharon of Hansen Hills, California
Source: consumeraffairs.com

In January 2021 I purchased a front load Whirlpool washer and matching drye
In January 2021 I purchased a front load Whirlpool washer and matching dryer. They were delivered on February 6 2021. The first load we found water on the floor. I thought I didnt close the detergent drawer so I proceeded with the next load. Again I found water this even through the ceiling tile in room below. So with the next load I sat in laundry room to see what was happening. When on the rinse cycle water shoots out the front of the dispenser drawer.Contacted service, they sent repair man. He ordered new parts and I waited over 3 weeks for next repair call to find out that whirlpool had part all along. Repair man came again and still no resolution to issue. He was told to order same parts again - still no resolution yet again. I fought with Whirlpool till they said they would give me a new machine. Now fighting because delivery people wont uninstall 1st washer and install new machine. Today is June 28 2021 and I still DONT HAVE A WASHER TO USE. I havent even used the dryer yet. I have $3400 and numerous hours with Whirlpool trying to resolve this issue! Can you help? Whirlpool continues to string us along, telling us to be patient, theyre doing their best.
Published: June 28, 2021
Patti of Springdale, PA
Source: consumeraffairs.com

Two Whirlpool washers in six years that the barren in back of tub goes out.
Two Whirlpool washers in six years that the barren in back of tub goes out. When the first one went out in the same month the warranty expired, I was told by a repair man that it was not worth repairing because of the cost. I purchased a brand new Whirlpool and only months later, the same parts are broken on this new front loader. How cheap is the Whirlpool app. made? Whirlpool wants to only send me a tech. to fix washer instead of replacing unit altogether. After all, the unit is only a few months old. I cannot believe I have to deal with this again.
Published: December 21, 2011
Lisa of Cut Off, LA
Source: consumeraffairs.com

Bought this washer in 2013 for close to $800. About a year and half old it
Bought this washer in 2013 for close to $800. About a year and half old it got real loud sounds like a freight train. Asked whirlpool repairman about it, and was told it is a main bearing going out. He said it would cost over $500 to fix it. Whirlpool warranty sucks - only one year. Called whirlpool, told them the problem and asked if this is a problem with this washer. Got told no they have no problems with it. Found out later not only do they have this problem with it they change design because of it. Repairman said his own daughter had same problem and he had many service calls on this model all with same problem. WHIRLPOOL WILL NOT REPAIR OR REPLACE PRODUCT WHICH IS A MANUFACTURE DEFAULT. It sets in our house unusable. I will never buy a whirlpool product again. Sad because that use to be all I would buy.
Published: March 26, 2016
Dan of St Francis, KS
Source: consumeraffairs.com

The Whirlpool Quiet Partner II is a horrible dishwasher and should have nev
The Whirlpool Quiet Partner II is a horrible dishwasher and should have never made it to a store to be sold. We have had the dishwasher for 4 years and about 6 months ago it started shutting off minutes after it was started. We would have to press the Cancel Button and try it again several more times prior to it finally completing the wash. After contacting our home warranty for help the tech said it is not worth fixing and will only give us a SMALL amount towards a new dishwasher.
Published: December 1, 2015
Danielle of Houston, TX
Source: consumeraffairs.com

I have a Whirlpool Duet Steam Washer that will be two years old in Septembe
I have a Whirlpool Duet Steam Washer that will be two years old in September 2013. It has been making terrible, loud noises during the spin cycle for a few months now. Repair tech told me it was the bearings and very costly. It will cost me over half of the original cost to repair a less than two year old washer. This is my second Duet front loader from Whirlpool. The first one was a drum issue and the rod ended up snapping. Again, very costly so I bought a new one. I should have learned my lesson the first time. I do not agree with extended warranties and it is just an additional money maker for the manufacturer. They should be making the product so people do not have to purchase those. Anyway, back to the washer at hand. I refuse to spend that much on a newer washer and will never purchase a Whirlpool product again. I will let this thing bang for as long as it is going to last. Unfortunately have also just purchased the dryer that matches this washer since I still had the old model Duet Dryer, so kind of stuck with them. Spent an hour and a half yesterday on the phone talking to people at Whirlpool and they really dont care if you have an issue or not no matter how old your machine is. They just want you to have purchased the extended warranty or forget it. There should be a recall and they should be helping these customers who all seem to be having the same issue. Done with them!!
Published: July 18, 2013
Debra of Janesville, WI
Source: consumeraffairs.com

My washing machine quit working with one month left on the warranty. In try
My washing machine quit working with one month left on the warranty. In trying to schedule repair I was never able to talk to a live person. Via chat and online scheduling they could not or would not come out for 10 days. Also they would not approve use of a local repairman who was willing to work on it in 2 days. Waiting 10 days for service on a washing machine is crazy.
Published: August 20, 2021
Barbara of Red Boiling Springs, TN
Source: consumeraffairs.com

The dishwasher chopper blade broke, and the check valve is gone. My over-th
The dishwasher chopper blade broke, and the check valve is gone. My over-the-stove microwave handle came off in my hand, and the top cover for the fan fell off in a pan of hot grease and almost burned me. What the hell is wrong with this picture? I paid a lot of money for inferior products, and I cant find replacement parts anywhere. And they are expensive when you can find them.I have tried to get this resolved before I talked to a rep, and your computers were down. I will never buy another Whirlpool again, and I am spreading the word. Dont buy Whirlpool. I am thinking of posting this on Facebook.
Published: January 29, 2012
Linda of Palmdale, CA
Source: consumeraffairs.com

When we bought our house the Matching set of Whirlpool Cabrio Platinums cam
When we bought our house the Matching set of Whirlpool Cabrio Platinums came with it as they were new. I decided to keep them and sell my LG Troms.Absolutely the worst mistake was keeping these Whirlpools. Who in their right mind would consider a washer with no agitator a washing machine? The clothes just sit and do nothing. They don’t get clean at all. Its a complete pile of useless junk and the person or persons who engineered it shouldn’t even be in charge of designing birdhouses.Whirlpool themselves should be ashamed to put out such a pile of garbage to the consumer. Our house came with all new Whirlpool appliances and we are going to replace them all and never give Whirlpool a look again. Whatever you do don’t fall for the shiny unit, slick salesmen. Because all youre going to get with Whirlpools washer is all talk and zero action. Thanks for the not so clean clothes Whirlpool. The local laundry mat thanks you when I need to actually clean my clothes.
Published: November 12, 2017
Curt of Rosemount, MN
Source: consumeraffairs.com

I have had this washer for a little over one year, it now does not work! I
I have had this washer for a little over one year, it now does not work! I had a service tech out to look at it.. The motor gets too hot and the switchboard stops working. I have called Whirlpool twice and the options they have given me are not good! Basically it would be about half the price of a new washer! I should not be having these problems with a washer this new! I am very disappointed with Whirlpool and wont purchase this brand again!
Published: June 5, 2015
Dayna of Oregon, OH
Source: consumeraffairs.com

Bought Model# wtw4800xq4 washer @ Lowes 9/01/13. Started having problems wi
Bought Model# wtw4800xq4 washer @ Lowes 9/01/13. Started having problems within months at our beach cottage unrented, our use only, no more than 4 small loads a month. Replaced circuit board, still same problem - stuck in rinse, never drains, wont spin. Another company came out, replaced solenoid. Thank God we bought year extended warranty. Quit again. Have to wring out clothes by hand, rinse out soap in sink. Another company comes, replaces shifter, breaks again. I go to Lowes, demand new unit. They send another company out, broke next day 1 load later. Got new washer from them same model. Within months problems start again. Now broken again. After new shifter 3 months ago, songs like rocks in coffee can. PIECE OF JUNK. CALLING again for service after Christmas. Absolutely disgusted with Whirlpool and the whole lack of admission of design flaws. NEVER WHIRLPOOL, new mantra here.
Published: December 13, 2015
Stephen of Oak Island, NC
Source: consumeraffairs.com

I purchased a Whirlpool Cabrio washing machine in October of 2016. This has
I purchased a Whirlpool Cabrio washing machine in October of 2016. This has to be the worst purchase ever. I agree with most of all complaints I have read. I am using more water, electricity and time to get one load half clean. How can this be efficient? The only problem I dont have is the noise; very quiet as if it goes to sleep. Seems to me the company has misrepresented this machine in its claim of being high efficient, washing (cleaning) machine. I too say Do Not Buy this Machine!
Published: May 19, 2017
Susan of Lavernia, TX
Source: consumeraffairs.com

The microwave keypad is worn down after 10 uses making it difficult to read
The microwave keypad is worn down after 10 uses making it difficult to read the pad. I just discovered the microwave was missing the front leg and they do not have a replacement part so I am stuck with a virtually new microwave that will not balance. It took 4 phone calls to their customer service department to try and sort out the problem. Poor product and extremely weak customer service department.
Published: June 27, 2016
Kate of New York, NY
Source: consumeraffairs.com

I absolutely hate this Cabrio machine. This should be off the market. Shame
I absolutely hate this Cabrio machine. This should be off the market. Shame on them for selling this. Salesman sold me a bill of goods on this washer and dryer. I have to wash some clothes 3x or hand wash. Whirlpool told me to use bulky or delicate cycles, as this puts more water into the machine so my clothes will rinse clean (doesnt work). When I wrote, they didnt even offer to make a service appointment. They know they have a bad product! I agree. Greed.
Published: August 17, 2012
Nancy of Haddonfield, NJ
Source: consumeraffairs.com

I bought a Whirlpool washer WTW4800XQ top loader. I have owned it for about
I bought a Whirlpool washer WTW4800XQ top loader. I have owned it for about two years and now it has tore up, the repair bill will cost almost what I paid for the washer. I feel it is bad business to sale something and it not last any longer than it has. No one should have to buy a washer every two years!!!! When it gets to the spin cycle it works fine and then all of a sudden it will beat and bang and if you dont get it stopped it will be in the middle of the floor. Im very upset and put out with Whirlpool!!!!
Published: January 30, 2015
Amy of Maysville, GA
Source: consumeraffairs.com

I am extremely dissatisfied with my Whirlpool refrigerator. After less than
I am extremely dissatisfied with my Whirlpool refrigerator. After less than two years, the entire cooling system has gone out basically rendering it a piece of trash. Unfortunately, Whirlpool is only going to absorb the cost of parts, so I still have to shell out $4500 to have a refrigerator repaired that is nearly new. This is not acceptable. I will never purchase a Whirlpool appliance again.
Published: February 16, 2015
Heather of Boulder, CO
Source: consumeraffairs.com

Purchased my Whirlpool dishwasher in 2005 model number GU2500XTPQ3. So it w
Purchased my Whirlpool dishwasher in 2005 model number GU2500XTPQ3. So it worked for about 10 years and I am fairly happy with that but I have a warning, my control panel shorted out putting out thick black smoke and I was unable to turn off the dishwasher. I had to turn off the switch at the breaker box. If my wife had of been the only one home she would not have known how to turn it off and would have had to call the fire department. I dont know if the short would have led to an actual fire but with that much heat I have to believe it would have. Warning, dont run the dishwasher when no one is home. Hope this helps someone.
Published: January 25, 2016
mark of Westland, MI
Source: consumeraffairs.com

DO NOT buy Whirlpool branded electric ovens. Whirlpool put out an update an
DO NOT buy Whirlpool branded electric ovens. Whirlpool put out an update and it fried the control board of our electric built in oven. They refuse to fix it. They have kept us on hold for two hours and then tell us there is nothing they can do to fix it. We had an extended warranty that just “disappeared from their system.” They told us someone would call back us but no one has. This was an update we were told we had to run in order to use the associated APP. Our oven is only 2-years old. We now will need to pay for the repair ourselves. DO NOT BUY.
Published: October 27, 2020
Leigh of Coatesville, PA
Source: consumeraffairs.com

I bought my first Cabrio set in 2008 to replace Maytags that lasted forever
I bought my first Cabrio set in 2008 to replace Maytags that lasted forever but looked their age on the outside. No problem with cleaning and drying, just wanted something new. What a mistake! I looked in Consumer Report Guide to pick and found the Cabrio set. Had problems after the first 4 months - UL uneven load codes flashing up, and had to replace suspensions and bearings, boards, etc. Unfortunately within that 4 months I bought another Cabrio set to put in my vacation home. Started with the same issues and really hard to get a service technician to come out because of where we were located. Customer service with Whirlpool sucks as well as Sears service. It is AMAZING to me that Whirlpool will NOT stand behind this product. I am writing this as I see an F1 code flashing on my washer here at my second home. I have a load of towels in it and house guests arriving in the morning! I will be trashing this washer and dryer and finding something old school and reliable. I want no bells and whistles, just clean and dry clothes. Whirlpool, you should be ashamed.
Published: June 30, 2014
Leslie of Lago Vista, TX
Source: consumeraffairs.com

Whirlpool Dryer Model #108409 - This dryer has given me problems within a y
Whirlpool Dryer Model #108409 - This dryer has given me problems within a year of purchasing it. I thought that I was investing into a good product by paying more money, $1677 to be exact. Technicians have been to my house on three different occasions and yesterday the repairman wrote that the dryer in not repairable. Badcock Furniture store in Hinesville, Georgia said that they can do nothing. BWG, who is responsible for the warranty, wants to charge me to have it repaired even against the report of the repairman saying its non repairable. VERY FRUSTRATED WITH WHIRLPOOL... I will never by another Whirlpool product. I bought this product in April of 2012 and it did not make one year before it started giving us problems. The repairman also said that the dryer was probably dropped in transporting it and it could not be detected from just looking from the front view.
Published: June 11, 2013
Larry of Hinesville, GA
Source: consumeraffairs.com

I purchased our brand new double ovens on 9/27/11. I was happy until 11/3/1
I purchased our brand new double ovens on 9/27/11. I was happy until 11/3/11 when the inside glass exploded, shooting shards of it all over our kitchen during the self-cleaning cycle. I immediately called Kitchen Aides corporate office in Michigan. She said that she could send a technician out to access the damages but didnt see that this was a product issue. Like I dont know how to properly push buttons to self clean! The technician came out the next day and said that he was only authorized to replace the glass, nothing else. He couldnt tell me why it shattered, he thought perhaps there was a bubble in the glass during manufacturing. I said I think it needs a whole new door at the very least, but more likely a new unit. I just paid $3000 for what will be a refurbished oven after one month of use. Today, I called once again to tell them that I am not satisfied with new glass, not to mention my oven is unusable in its current state and still has glass sipping out. I spoke to a woman in their safety committee department, who told me that Whirlpools warranty is replacement of broken parts, nothing more, and since only one pane of glass broke and not the door physically, they couldnt authorize a new door or new oven. Mind you, that we still dont know why it broke, was it just faulty glass or could it be a heating problem? She didnt care, only that they could only repair the glass. I asked if the glass could be overnighted since I have been without an oven for four days now. She said that she had no way of doing that, so I asked if I could speak to the parts department and she said I could not, that only techs could contact them. I asked if she could do anything for me? Could she assure me that it would be fixed within the week? No. Could she assure me that it would be fixed by Thanksgiving? No. Whirlpools policy clearly is that once you purchase their products, they have no intentions of listening to their customers complaints or concerns only to do the very minimum required.
Published: November 8, 2011
Janice of Ladera Ranch, CA
Source: consumeraffairs.com

The Worst experience with Gold Series Mod WRF 757SDEM01. Purchased from Bes
The Worst experience with Gold Series Mod WRF 757SDEM01. Purchased from Best Buy June 2016. $2215.00. Within 6 months The interior light began going dark within 6 months. Our very reputable warranty repair service ordered a part that did not repair it. Was only temporary. They did figure out that the circuit board was bad and promptly took care of our problem. Next I kept noticing water appearing on our wood flooring. Let it go because it only appeared sporadically. Called Whirlpool only to find out they switched to a warranty repair service that was inept and inexperienced. Said he could fix it. Blamed it on a freeze-over so I let floor dry up then re-started and refilled. Thought he did fix it cause it made sense. When reassembling he broke to upper freezer try glide. Then 3-4 weeks later I notice one morning water again on my wood floor. The dripping had been running beneath the wood slats and had seeped up through the joints. Now the flooring wood has swollen and will need to be replaced because of this. This is the second time I had to unload all food and store at neighbors and give away. Extremely poor engineering designs as each time the ice dispenser is used, nothing prevents ice from flying out onto the floor ever since day one. Same with water. The release does not shut down to prevent water or ice from pouring out onto the floor when removing any size cup. The refridge doors must both be opened to use the lower level drawer. Loses much cooling with having to always open both. Next, weve come home MANY times with the left refridge door partially open because of the difficulty of the mechanism to secure at closing. This happens to us 5 times a week for three years-honestly!. This was the only refridge we could find that would fit our opening in a 20-yr-old home. The fridge is so heavy one man cant pull it out of its opening. Only 2 very small wheels in front and skids in rear stick due to weight. Weve confirmed this is not a spigot leak from the ice maker. Finally (but probably not) the ice container allow much air in because of having to open the left door that your ice is always melted together plus it too small for a family of two and ice must be purchased when entertaining. And to top it off, the human that took the warranty call this time is foreign and my wife could not get them to get our last name spelled correctly nor the phone number correct after constantly repeating it. This unit and model is an absolute lemon. Im going out today to find another unnecessary $2500.00 to buy another.
Published: September 16, 2019
Ran of Edmond, OK
Source: consumeraffairs.com

Cabrio washer lid warps twist and cracks the frame. Not a proper lid design
Cabrio washer lid warps twist and cracks the frame. Not a proper lid design apparently.
Published: August 2, 2013
Steven of Hamilton, MI
Source: consumeraffairs.com

Whirlpool WRF993FIFMOO: Refrigerator Problems: the doors do not close, both
Whirlpool WRF993FIFMOO: Refrigerator Problems: the doors do not close, both ice makers went out, The computer on the filtration will go off. Refrigerator had problems maintaining temperature since 8.12.17. The refrigerator no longer works. This is my second unit since 11.09.16. It came from nfm.com.
Published: August 26, 2017
Marquette of Lavon, TX
Source: consumeraffairs.com

Just cleaning the outside of our piece of ** oven. Must have hit either the
Just cleaning the outside of our piece of ** oven. Must have hit either the on or off button to lock because the damn thing locked. Tried unplugging it, pushing all the buttons suggested on these websites, etc. Hell, even tried to call Whirlpool, where I just talked to a computer. Lesson learned: Whirlpool wont get our business again. Period.
Published: January 24, 2014
el of New York, NE
Source: consumeraffairs.com

Our 2 yr old Whirlpool Gold refrigerator (French doors, bottom freezer) sto
Our 2 yr old Whirlpool Gold refrigerator (French doors, bottom freezer) stopping freezing/cooling. When we got a repairman to come take a look at it, he said the compressor is not working. The warranty on the fridge is only 1 year. However, the compressor is the main component of a refrigerator, and the repairman said 5-6 years is the minimum it should last before breaking. I called Whirlpool and asked them to pay for the repairs of what is quite obviously a defective part. They refused. Needless to say, I will never, ever buy another Whirlpool product again.
Published: July 26, 2013
Chris of Arlington, MA
Source: consumeraffairs.com

As you have heard from 700 other people we bought a whirlpool refrigerator
As you have heard from 700 other people we bought a whirlpool refrigerator because GE sucks, brand new refrigerator died in 4 years with 4 service bill costing more than the refrigerator. So we did some research and whirlpool was being recommended by several stores and the reviews were better than most. Well we bought the Whirlpool refrigerator and it has been nothing but problems from the start. Everything that can go wrong has and of course our warranty ran out. And we are sitting here with no water, no ice, water tray falls out and breaks. Called whirlpool many times and their answer every time is, we will send someone out for you, and then we get a 300 to 400 dollar bill. Whirlpool sucks as bad as GE. Its crazy these companies get away with this crap. They can build good refrigerators they have in the past. My grandparents have one for 25+ years, now you cant get 2 years out of them. Pure Junk! I dont know what a good brand is anymore, they all seem to suck. Good luck.
Published: October 30, 2014
Chad of Sarasota, FL
Source: consumeraffairs.com

We brought this in Jun 2015, within 1 weeks it developed its problems. Ive
We brought this in Jun 2015, within 1 weeks it developed its problems. Ive had service men out 10 times for ice buildup on the freezer side, and the refrigerator side not cold even on max setting, and the problem hasnt been solved yet.
Published: December 17, 2015
Sandy of Orlando, FL
Source: consumeraffairs.com

I had a kitchen fire in 1999. All appliances were replaced with Stainless S
I had a kitchen fire in 1999. All appliances were replaced with Stainless Steel Whirlpool. My old fridge was an 18 y.o. Whirlpool and still works fine in the garage. My old above range microwave was 12 y.o. and worked fine, I should have kept it. I had to replace my new Whirlpool Microwave after 4 years and 4 repairs. (Main Power Diode kept failing). Now my Whirlpool Gold fridge is not defrosting, even the freezer light switch is frozen. This French door freezer also seems to have less capacity than my old upright freezer. The retailer seemed sympathetic and pathetic. They would not budge on repairs. I told the contractor that did the rehab on my house what happened, he said he would stay away from Whirlpool and that retailer.
Published: July 5, 2015
Joseph of Perris, CA
Source: consumeraffairs.com

We purchased a Whirlpool Overhead microwave and Quiet Dishwasher in May of
We purchased a Whirlpool Overhead microwave and Quiet Dishwasher in May of 2017. Within the first year, the microwave needed new sensors installed. The repair person said this was a design flaw and he was getting many calls. Then at 13 months, the dishwasher wouldnt drain. The repair person fixed the problem and left reset directions because this can commonly happen. Now at 18 months later, the drainage problem wont resolve even with the reset. Whirlpool extended the warranty by 6 months but wont cover this repair. Two appliances, two problems. Dont buy Whirlpool.
Published: December 5, 2018
Laura of Thompsons Station, TN
Source: consumeraffairs.com

Our Whirlpool refrigerator has been an extraordinary kitchen appliance, it
Our Whirlpool refrigerator has been an extraordinary kitchen appliance, it may even be 28 years old. The ice maker worked until just four years ago and thats amazing. Its never been serviced and never needed a repair. I dont know what one can say about something thats worked so flawlessly. This seems a little bit trivial when considering the cost of a new appliance, but the plastic veneer on the handle had fallen off and needed glued back on, but thats about it as far as maintenance and repairs go. Overall its been an ideal purchase and I wish wholeheartedly all my purchases were as good as our whirlpool refrigerator.
Published: February 12, 2021
Ron of Raleigh, North Carolina
Source: consumeraffairs.com

I have posted on here in the past about the problems with the Cabrio Washer
I have posted on here in the past about the problems with the Cabrio Washer from Whirlpool. Our third top load lid was just ordered since 2011. There is a design flaw where the plastic frame around the lid cracks and causes the lid to hump up. While shopping at a local appliance store recently, I saw a new Cabrio washer and the lid and hinge system has be re-designed. I wonder why?????
Published: December 10, 2013
Frank of Dover, OH
Source: consumeraffairs.com

We have had a Whirlpool hot water heater for 6 years and 14 days. Note the
We have had a Whirlpool hot water heater for 6 years and 14 days. Note the 14 days. It has been nothing but trouble and we have called the company repeatedly for help. It finally stopped working altogether 14 days after the warranty ran out. Thank you Whirlpool for nothing! It had a filter on the bottom of the heater that constantly had to be cleaned which was next to impossible. We had to buy a special brush to try to reach it. My husband had to take it apart several times a year and clean it to keep it running. Whirlpool should have replaced it within the first year but instead offered many suggestions about cleaning and etc. so they would not have to replace. Today it is out of my house for good and I would advise anyone reading this to beware! Horrible product!!!
Published: June 23, 2018
Sherry of Ava, MO
Source: consumeraffairs.com

I purchased it in 2011 for $1100 Canadian. Smooth glass top and true convec
I purchased it in 2011 for $1100 Canadian. Smooth glass top and true convection. The controls were easy to use, and understand. What bothered me was that it stopped working just after the warranty ran out. I did my research, and found that the newer ranges that have the controls on top at the back have issues with the motherboard overheating, and causing this problem. I did speak to Whirlpool customer service, and managed to convince them to supply the replacement part at no cost. I paid my local dealer to install it. This repair lasted for just over 1 year. Same problem again.This time I could not convince Whirlpool to supply the part. FYI The part in question is the controller. Essentially a motherboard. All the controls are operated through this small computer. It is the only replacement part that costs over $100. Last I checked it was around $450 Canadian. The reason for the fault is overheating. According to the tech that fixed it the first time, it is the most common problem with this style of range. I find this concerning considering the only thing a range does is create heat!Keep in mind that you are virtually held over a barrel. There are only two companies that market their products under multiple names adding up to over 80% of the appliances on the market. They battle for that market by offering more bells and whistles, and less quality. The Range I replaced four years ago was 20 years old. I just replaced my Whirlpool 3 months ago. I went outside of the 80%, and bought a Samsung. Im rolling the dice, and went with induction top. My theory is it will produce less heat because it just heats the pot, not the stove top.Low quality drives me nuts. I want fewer bells and whistles, and more long lasting reliability. I should be able to go my lifetime and only buy two or three ranges. We really like the induction top. It works fast, and doesnt produce too much excess heat. Dual zone oven is a good idea. We werent looking for it, but there was a deal on. The dual zone induction range was only $50 more than the regular one beside it. Now my wife uses it all the time. She will have cookies in one zone, and a casserole for supper in the other. True convection is the other must have. It does a great job cooking everything evenly.
Published: March 16, 2016
Steven of Clarington, ON
Source: consumeraffairs.com

I purchased a Whirlpool Cabrio washer and dryer from a local appliance cent
I purchased a Whirlpool Cabrio washer and dryer from a local appliance center. Everything was working great. After some time, the washer began to have error codes. I would have to turn it off and restart using more detergent, more water and more electricity to attempt to get a load washed. I did purchase an extended warranty. I reported the issue to Whirlpool and I have had 7 home repair visits while still under Whirlpools warranty. The first time, the repair tech went under the washer and tightened a screw. REALLY! The next visit, the motherboard was changed and the issues kept coming back. Well, the Whirlpool warranty was now over so the extended warranty had to be picked up from the appliance center. Things got worse and had continued repair calls. After I had enough, I called Whirlpool and spoke to everyone under the sun. I tossed it outside and bought another brand washer. Several weeks went by and this washer still under the shed, Whirlpool contacted me and bought back my washer, GREAT.Now, here it starts all over again with the dryer, same issues with motherboard. Only this time, I am 1 month out of Whirlpool warranty and need $385 for a new motherboard plus cost to replace. I call Whirlpool again but only this time, they show no issues with this dryer and are not budging. I toss it out and again, purchase another brand dryer. I grew more angry by the day looking at this dryer sitting useless outside. I had it hauled off as trash. My question is how does a consumer protect themselves against these manufacturers? I do understand warranties but if it smells like a lemon, acts like a lemon, it must be a lemon!
Published: August 27, 2013
Jim of Denham Springs, LA
Source: consumeraffairs.com

In all of my 50 years of marriage and buying stoves, I have never had an ov
In all of my 50 years of marriage and buying stoves, I have never had an oven breakdown. I live in Canada - I purchased three appliances, all Whirlpool 2 years ago. I had to have a service call on the fridge three weeks ago - a little rubber nipple was clogged up and water was running into my freezer. Bill $100.00 - two weeks ago, the broil element in my stove would not turn off when the bake cycle heated up. Actually, you did not have to press the fast heat button as the broil came on by itself. I have been waiting almost two weeks for the part - today I was told it would be another week. The part has to come from the US - what ever happened to Whirlpool Canada???? - I am told the bill will be $350.00 and maybe more plus the service call. I do not find this acceptable. What do you do when you have already invested the money in the product. Bring back the old Moffat stoves. I would like to be reimbursed for the money I have put out and will put out.
Published: October 2, 2013
Mary Ellen of Elora, ON
Source: consumeraffairs.com

In August 2011, I purchased and had installed a Whirlpool Wall Oven RBS305P
In August 2011, I purchased and had installed a Whirlpool Wall Oven RBS305PVQ04 for $1000+. In July 2014, the oven failed with blown internal fuses and a thermostat $225+. In November 2014, the oven failed again, this time with a failed controller board. Whirlpool claims there are no replacement parts after just three years! In calling Whirlpool customer service for help, they basically said tough luck! NO parts, NO adjustments, NO service, you own a boat anchor. I tried to buy American; boy, was that a mistake. So it cost me $415 per year to own this LEMON. DO NOT DEAL WITH THE WHIRLPOOL COMPANY!
Published: November 12, 2014
Jeffrey of Gardnerville, NV
Source: consumeraffairs.com

I really like my new 5 burner gas double oven gas range made by Whirlpool.
I really like my new 5 burner gas double oven gas range made by Whirlpool. Except for 1 minor flaw where the backsplash panel warped at the beginning and was promptly replaced by whirlpool I have had no problems with my range, love having 5 burners and a double oven. Plus the left front burner has a much bigger burner with higher btu which helps water come to a boil way faster than any other ranger I have ever had. That is a real nice feature and I really like having 2 ovens, When cooking on an average day for my small family there is no need to heat up the big oven and the little oven is just the perfect size to bake 1 or 2 dishes. And on holidays when I am cooking for more people or many more dishes I have the capacity to cook more items.
Published: February 7, 2021
Teresa of Clayton, Ohio
Source: consumeraffairs.com

I suppose the idea was good - less water. However, when you are washing clo
I suppose the idea was good - less water. However, when you are washing clothes, water and agitation are key. Without an agitator, clothes are just spun around with water and detergent. This washing machine (WTW4950XW2) couldnt clean any dirt off clothes. Clothes go in dirty. They come out damp, wrinkled, and dirty. I got this washing machine free from my father and am thinking I got ripped off. No wonder he gave it away. Piece of junk.
Published: October 24, 2013
Stanley of Delmont, PA
Source: consumeraffairs.com

We have had this washer for a year and the longest it has run before breaki
We have had this washer for a year and the longest it has run before breaking down is 3 weeks. Since it takes longer than that to get a repairman out to look at it and another 2 to 4 weeks to get parts, it has run less than half of the time we have owned it. This thing is a hunk of junk. Dont ever consider purchasing one of these lemons.
Published: August 8, 2015
William of Opelika, AL
Source: consumeraffairs.com

When I bought this stove, I already had a glass top (Sears) which was satis
When I bought this stove, I already had a glass top (Sears) which was satisfactory but I changed to get a convection oven, never had a problem cleaning the glass top. To me, Whirlpool was, and I emphasize WAS, a reputable manufacturer and the stove offered everything I needed. Not so, the glass top is a nightmare to clean; no amount of elbow grease works. It is like cooking on a mirror. Talked to everyone I contacted but, it seems, I am the faulty element in this problem: I DONT KNOW HOW TO CLEAN!!! YOU NEED A FIRST OF SOMETHING FROM TIME TO TIME AND THIS WAS A FIRST FOR ME.They told me the only solution they could offer was to buy their own cleaner. Why do they need to market their own cleaner? I did not buy a museum piece that needed to be treated with special care, I bought a stove to cook on. I want as many people as possible to know about that uncleanable glass top. Every time I need to cook, I cringe at the amount of time and effort I will have to spend to get it clean. I am not a novice, I have been doing housework for the past 60 years. Beware, it is a most frustrating situation to having paid top dollars and to be stuck with a product that brings such frustrations. By the way, it was bought at The Brick in Canada. They were not helpful either.
Published: August 3, 2016
Joan of Cornwall, ON
Source: consumeraffairs.com

I purchased this washer about 3 years ago to replace a dishwasher which las
I purchased this washer about 3 years ago to replace a dishwasher which lasted 20 years. Within a year the racks began to rot, the front panel plastic started to peel off. Within two years half of the racks rods completely rotted away. 3 years later the washer is busted - most likely pump which was probably blocked by one of the pieces of the rack rods. I am replacing it with Bosch - German engineering. Needless to say I will NEVER buy a Whirlpool - formerly reputable company again. Good-riddance Whirlpool.
Published: October 23, 2014
Radomir of Lawrenceville, NJ
Source: consumeraffairs.com

Purchased Whirlpool dishwasher and range approximately 16 months ago. Dishw
Purchased Whirlpool dishwasher and range approximately 16 months ago. Dishwasher must stop in middle of rinse cycle because the dishes always feel filmy and there is an inch or two of water in bottom. Must be bailed out by hand. Piece of garbage. Called Whirlpool and they can get us a service man from 8-4 (who waits an entire day these days) on New Years Eve. Next appointment is following week to examine and will fix (if it is their fault and for a fee). The last two dishwashers I purchased lasted 10 and 7 years respectively. Stay away if you dont want bad equipment, uncooperative service, and aggravation. Range I bought was OK but the oven temperature is always off 10-15 degrees from what it says it is. I honestly wanted to buy American but I feel cheated. Next time Ill try Samsung and see if they give a damn.
Published: December 24, 2020
Noah of Brooklyn, NY
Source: consumeraffairs.com

I love the large capacity of the washer. But something is turning my whites
I love the large capacity of the washer. But something is turning my whites YELLOW! I have never had this problem in 40 years of washing clothes. All of my whites come out yellowish and I am getting what could be rust stains on heavier cloth (white denim). Also, I regularly used the soak setting on my old Whirlpool. That setting is not available in the Cabrio. I have tried catching between cycles and the drum is constantly emptied. I wish Id read these reviews before I bought.
Published: September 2, 2013
Kathy of Bakersfield, CA
Source: consumeraffairs.com

Very durable. Not pretty but will last a long time. The dishwasher will run
Very durable. Not pretty but will last a long time. The dishwasher will run forever. The appearance is bland so the product is nothing fancy. It gets the job done. The machine is very quiet. I think this feature is the best one.
Published: March 12, 2020
Tryphenna of Stonecrest, Georgia
Source: consumeraffairs.com

I purchased this washer 4.5 years ago. I have always been a Whirlpool custo
I purchased this washer 4.5 years ago. I have always been a Whirlpool customer. My parents had Whirlpool washer and dryer while I was growing up in the 60s. When I got married in 1976 I bought a Whirlpool washer, dryer and refrigerator. They lasted 19 years!!! Then I replaced all 3 in 1995. Again, lasted 16 years. I gave the washer and dryer to my sons when they moved out--its still working.So I thought I would reward myself with a new Whirlpool washer and dryer in August 2011. I didnt know about the pitfalls with the high efficiency washers. The dryer is great, but I HATE my washer! The lid lock is ridiculous, we should be given an option to override it. The sensing takes forever. The low water level leaves clothes unclean, and with detergent residue, causing the need for another rinse cycle. This saves no water if you have to run it twice. Not to mention how long it takes to do a load. Then it doesnt spin all the water out and you have to run a spin cycle. It aggravates me every time I do laundry. After being a Whirlpool customer for over 35 years, its time to move on. I just ordered a GE machine that is old school, no sensors, no lid lock, and I can control the level of water. Whirlpool doesnt make these simple machines anymore. Youre going to lose a lot of customers if you keep selling the trash. This is the worse washer I have ever had. My adult son went into a rage last night trying to use it, he forced the lid open and broke the lock, and of course it wont work at all without the lock. Good thing I ordered the GE washer the day before, it will be here in a few days. Cant wait to bash the Whirlpool with a sledge hammer, it will give us great satisfaction! Are you listening Whirlpool? Your designers need to go back to the drawing board. I realize this is not just a Whirlpool problem. Ive seen complaints about kenmore and every other manufacturer that makes these stupid low water sensing machines with lock lids. If consumers are too stupid to keep their kids out of the washing machine, maybe they should have their kids taken away.
Published: March 8, 2016
l. e. of Brea, CA
Source: consumeraffairs.com

We saw water all over my wood floor and traced it to the lower freezer unit
We saw water all over my wood floor and traced it to the lower freezer unit of my 15-month old refrigerator/freezer. We had to call a repairman which traced the problem to a frozen defrost. He put in a new thermometer at the tune of $200 and now we have to deal with a wood floor problem on top of it. I purchased because Whirlpool was always known to be a quality product. I wont make that mistake again.
Published: March 13, 2012
Sandra of Oshkosh, WI
Source: consumeraffairs.com

I purchased a washer 6 months ago and it was starting by itself so I called
I purchased a washer 6 months ago and it was starting by itself so I called to get a technician out and it took them 3 days to tell me that they did not service in our area. Long story short I was out of a washer for 2 weeks talking back & forth with Whirlpool which was absolutely a nightmare. Kept me on hold forever and hung up on me several times so they didnt have to deal with the situation. Absolutely no customer service at all. When it came down to it they were going to issue me a new washing machine and I had to go to the store to get it and when I got to the store they told me I had a $415.00 credit to spend. Thats less than what I had paid for the washing machine and then I am having to spend an extra $200.00 out of pocket to get another washing machine.My warning to you is not to purchase any Whirlpool appliances unless you want to go thru pure hell. These people do not care about anyone after the product is sold. Their customer service sucks, their appliances suck and Whirlpool just sucks all the way around!! Worst experience I have ever had and I hope they never sell another appliance again!!
Published: December 14, 2017
Michael of King William, VA
Source: consumeraffairs.com

We purchased a Whirlpool refrigerator in 2010, model #ED2KHAXVB01, side by
We purchased a Whirlpool refrigerator in 2010, model #ED2KHAXVB01, side by side with ice maker. Fortunately, we purchased a 5-year service contract at the same time because the ice maker has broken twice. Unfortunately, I have had to replace the shelves while still under warranty quite a few times. The sides of these glass shelves are made of poor quality plastic and crack constantly. The drawers are the same way. The refrigerator is no longer under the warranty and Whirlpool wants $109 per shelf. I told them I would pay for replacement shelves only if they could send shelves that were made with better quality materials. Otherwise, I might be spending $1000 per year replacing shelves. The Whirlpool representative told me there is nothing that they can do. I see many people with this problem posting complaints on the internet. Do not buy a Whirlpool refrigerator. I have been married for 37 years and never had to replace one shelf in any refrigerator and still have a 40-year old refrigerator in my basement with no broken shelves!
Published: August 30, 2012
Donna of Centerport, NY
Source: consumeraffairs.com

Right from the start of buying a new suite of Whirlpool appliances, the lig
Right from the start of buying a new suite of Whirlpool appliances, the light over the range burnt out. We figured it was just a bad bulb so we replaced it. Soon it burnt out again, replaced it again, then again it burnt out. I finally called Whirlpool about the problem and found out it is the electronic panel that needs to be replaced... Of course at a full charge to me! I am so over WhirlPoo, (yes I spelled it that way on purpose) every single appliance has had issues. I have just lived without a light over my range because fixing it is more expensive than buying a whole new microwave. Never again will I buy any WhirlPoo appliance!
Published: April 18, 2019
Patrice of Gig Harbor, WA
Source: consumeraffairs.com

I bought a Cabrio from Costo less than 2 years ago. Dryer so far so good (b
I bought a Cabrio from Costo less than 2 years ago. Dryer so far so good (big barrel with hair dryer so what could go wrong?). Washing machine is HORRIBLE. Lid latch broke (couple hundred to repair). Now out of the blue I get an F2 error & machine is completely inoperable. I am only user & very careful with it. There should be a recall on this expensive junk. NEVER buy Cabrio or maybe any Whirlpool appliances again. Ive never written a bad review btw.
Published: November 10, 2015
Mis of Jax, FL
Source: consumeraffairs.com

I love the look and performance of my Whirlpool Dishwasher. It could be a b
I love the look and performance of my Whirlpool Dishwasher. It could be a bit quieter, but overall I have no complaints. My washer was already installed in my home when I purchased it and I must say, it helps when the family gets together and you don't feel like washing the dishes. The dual chamber pod holder is great if you need to use and the heat function works wonderful. I don't have the problem of the left over water that a lot of dishwashers leave behind and no spots!
Published: March 17, 2020
Latisha of Houston, Texas
Source: consumeraffairs.com

Whirlpool electric range oven wont turn off. Used the oven 2 or so times pe
Whirlpool electric range oven wont turn off. Used the oven 2 or so times per year.... Very unsafe, expecting internal breaker that would shut the thing down. Whirlpool Range/Oven PT3196685 happened on 6-10-2014, was baking cookies with timer on for 9 min. First batch turn out good, 2nd batch on fire before even get to 6 min, the burner is brightly hot and cant shut off from the panel... Saw ERR then COOL indicator... Tried but no respond from panel. The burner element wont turn off and temp keep rising white hot... The only way to shutoff is the house circuit breaker. But soon you turn on the breaker, the oven would turn on by itself and you cant switch it off. Where is the safety breaker on these range/oven when something goes beyond 500 degree..... UNSAFE PRODUCT. Ordered a new Whirlpool Gold 700 series but canceled after discovered others experienced similar situation with the new product. Could have burn down the house and worst when lives involved. WONDER IF ANYTHING WAS DONE TO CORRECT THESE SAFETY ISSUE.
Published: June 16, 2014
john of Savage, MN
Source: consumeraffairs.com

We bought a new Whirlpool washer/dryer 6 months ago. Dryer is ok, seems to
We bought a new Whirlpool washer/dryer 6 months ago. Dryer is ok, seems to take a long time to dry. Washer is horrible. It constantly goes off balance and shakes all over the floor. Once opened, the clothing may be a little off, but not enough to cause such commotion. SO FRUSTRATING! If we could afford to replace these, they would be out on the curb today!
Published: January 12, 2019
kerri of Holland, MI
Source: consumeraffairs.com

This is our second Whirlpool refrigerator that has the same defrost water d
This is our second Whirlpool refrigerator that has the same defrost water drainage problem. I was told this newer model had updated technology, not so, actually it is worse. My older refrigerator went about 8 years before I started noticing water on the floor and this newer model is 4 years old and it started having water overflow at 3 1/2 years. Then in April we replaced the water filter and the ice-maker stopped working. My freezer also stinks like stale water (my reason for replacing the old refrigerator plus the water on the floor). I followed a YouTube video for defrosting the drainpipe, it was very tedious, labor intensive, and time consuming and worked for 3 weeks. This is very upsetting. After spending $2500 to have such problems and my expensive $150 4-year extended warranty expired just weeks before the ice-maker went out. This is obviously a design problem that Whirlpool refuses to address since my other model was a year 2000 model and my 2013 has the exact same problem. VERY POOR customer care in addressing these design failures of both the defrost drainage (just make a larger drain port!!!) and the ice-maker.
Published: June 2, 2017
Donna of Rociada, NM
Source: consumeraffairs.com

The Whirlpool refrigerator I ordered from Home Depot came to my house dente
The Whirlpool refrigerator I ordered from Home Depot came to my house dented. I then had to get Maytag/Whirpool to send me the same model refrigerator which they then subsequently forgot to include the ice maker with the refrigerator. It has been nothing short of an act of Congress to get in touch with someone from their Customer Service department for them to send the ice maker that they forgot to include. Ive had to call them at least 15 times to get them to resend the missing ice maker. Absolute nightmare. 10/10 will avoid buying Whirlpool in the future.
Published: October 15, 2018
Tyler of New Orleans, LA
Source: consumeraffairs.com

My wife and I bought a Whirlpool water heater NU50T121-403, SER# 0733323 as
My wife and I bought a Whirlpool water heater NU50T121-403, SER# 0733323 as we researched online the best efficient water heater for the money... which was actually more than we budgeted for. We purchased it from LOWES and our Plumber had to return the first heater due to a huge dent on the outside of the body once it was removed from the box. LOWES replaced it, no problem and he installed it. GREAT, HOT water for about six (6) months. Pilot light went out and has continued failing after relighting numerous times! Now we have the four (4) blinks indicating that the Honeywell gas control needs to be replaced only after 27 months of use. Whirlpool offers 12 year warranty on tank & parts, but come to find out, not this part. We were both raised on Whirlpool products and thought we based on our parents successes of various Whirlpool products, we were buying quality brand. We were soon disappointed and will never buy another Whirlpool manufactured Brand again!!
Published: January 18, 2015
Mark of Atwater, CA
Source: consumeraffairs.com

Visa MasterCard

Site Secured By The Website Guardian
TOP