[Model WTW6300WW0, Type 580] A few years ago Whirlpool goofed - they left out the Perma-press cycle on a high-efficiency washing machine model.We noticed the absence of Perma-press (or Casual as it sometimes now called) on the shop floor, and were assured we could arrive at the same results with the dizzying array of buttons that allow the consumer to tailor the cycles to their wash load. It turns out that it doesnt allow this. Buttons are disabled on some of the cycles, thereby preventing recreating a Perma-press cycle. No amount of prodding... Whirlpool has provided me with an override for the combination of a normal wash and a gentle spin that comprise a typical Perma-press cycle.On contacting Whirlpool about the missing cycle, they claim consumers no longer want the Perma-press cycle. Puzzled by this statement, I returned to the showroom floor to see for myself. All the washers have Perma-press cycles. Whirlpool goofed with this model. They left it out. They have not provided a replacement machine for a consumer who blows this whistle on their goof. Among the solutions their customer support DID provide: add softeners to the rinse cycle and add dryer sheets to the dryer to reduce wrinkles [by purchasing a high-efficiency machine, we aimed to reduce waste, not increase it]. Among their invalid suggestions: choose the Casual cycle [there is no Casual cycle setting on this machine]; choose Normal cycle, then set spin speed to low [this machine disables the low speed choice on the Normal cycle]; on this machine the Perma-press cycle is renamed Delicate [Wrong. Delicate only swishes clothes back and forth, not robust enough for business shirt colors and cuffs]; on this machine the Perma-press cycle is renamed Colors [Wrong. Business shirts come out too wrinkled on Colors]. There has been nothing I can do to convince Whirlpool that they produced a lemon in this model [Model WTW6300WW0, Type 580] and should replace it with a normal washing machine. I have tried for years, only for Whirlpool to come to the same conclusion: its the consumers problem now, not theirs.

First of all, Whirlpool is fully aware of the problems with water heaters and intentionally places requirements on the consumer until they give up. This info from a distributor. I bought 30 gal. gas water heater 7 months ago. Six days ago the pilot light went out. Went to Lowes (purchased there) and bought a replacement. Wrong one. Returned to store and was told they dont stock repair parts, call factory. Monday called warranty number. They offers to send thermopile, it would arrive in 5 days. I paid $30 for overnight. Plumber installed new part. Still doesnt work. Whirlpool says have the plumber call them theyll walk him through troubleshooting. I ask, Whos paying the plumber? They reply, You are. Plumber calls Whirlpool. They tell him to clean the screen. He does. They tell him to disassemble the burner. I stop plumber. I ask Whirlpool, What if its not the burner? They reply, Then well troubleshoot something else. Meanwhile Im 5 days without hot water. I go to Lowes where heater was purchased. The manager thought it funny Im another victim. I ask, Why doesnt Lowes stock heater parts? He says because Whirlpool doesnt let them carry parts. Im beat. I surrender. Parts from Whirlpool would take another 5 days and theres no assurance itll work. Lowes refuses to assist.I go to Sutherlands and buy a $450 Rheem on recommendation from plumber. Manager from Sutherlands hears my sad story and writes on receipt: Any warranty failure and Sutherlands will replace water heater free. He signs his name on receipt. I pay plumber to swap out heaters. Anybody want a 7 month old Whirlpool water heater. Like new. Cheap! By the way... I originally went to a major appliance parts store asking for a thermocouple for a Whirlpool. The three guys at the counter started laughing Hey we got another one looking for Whirlpool parts. They didnt have them either. Lesson learned.

Our Whirlpool water heater needs a burner assembly replaced. Second time within the warranty period of six years. Parts have to be ordered, so you will be without hot water for several days to a week. The worst part is reaching them. Between my wife and I, we have almost 4 hours invested in sitting on hold waiting for someone in three different calls. They never answer the phone. They give an option to call back. They never call back. Im so frustrated. No Whirlpool products ever again. Im sitting at my desk, hoping someone will eventually answer the Whirlpool line. I dont even have the part ordered yet after two days of no hot water. Who knows how many more hours I will need to sit here and listen to this music on hold. It is incredible in 2021 a company can remain open while offering this kind of customer experience.

I purchased the Whirlpool Cabrio washer in 2011. It has been nothing but trouble since. I have had repair people out here several times, because the machine twists and tangles the clothes, doesnt get the clothes clean. Sometimes the clothes come out dry without even getting them wet. There are lots of soap scum too. I would NEVER buy another one of these. SO DISAPPOINTED.

I have owned a Whirlpool Gold Series Refrigerator for one year and 9 months. During that time I have had 7 repair issues. Each of the past ones took at least two weeks to repair. This past repair has to be redone because the new parts are also bad. The part is now on factory backorder. It will be at least two months for this to be repaired. Whirlpool says its too bad, we just have to deal with being without a working refrigerator for months. Do not buy this product!!! The warranty only means that you are forced to wait months for repairs. They will not replace, refund, or even extend the warranty for all this downtime. You have no recourse with the company.

We brought this in Jun 2015, within 1 weeks it developed its problems. Ive had service men out 10 times for ice buildup on the freezer side, and the refrigerator side not cold even on max setting, and the problem hasnt been solved yet.

Bought the hot water heater, installed it. It leaked from bottom. Whirlpool warranties it. Replace it with new heater. It too leaks. I Google problems with Whirlpool hot water heaters. Found over 1500 complaints.

I purchased a Whirlpool hot water heater several years back with every bit of the Bells & Whistles that Lowes could bestow on it paid for and documented on the tank; Limited Lifetime Warranty and Lowes Professional Installation. It failed after several years with multiple problems. First, the bottom heating unit failed at the same time, noticing a leak from the top heating units external cover where a supporting screw had popped out, leaking down to the floor. Not only was the Whirlpool 800 number a scham of silence, with no estimated wait time and after approximately 20 minutes, a rep picks up as I could hear their legal department on an alternated line instructing and listening in, then dropping off when those crooks felt I had been placated enough to go onto to the next sucker. I have all Whirlpool Gold & KitchenAid Superba appliances in my kitchen and never thought I would be saying this but I will never purchase another Whirlpool Appliance or shop at Lowes again!

Bought this model from Bad Boy in 2006 and just after the warranty ended the problems began. We kept getting the F1 error code so with a little internet research we found it was a known problem with Whirlpool. I contacted them and was told they knew nothing about this issue being nationwide, however I emailed them copies of the complaints and responses. They sent out a technician who had to replace the motherboard free of charge. Next issue was a loud noise coming from washer sounding like a jet plane taking off. Hubby ripped machine apart to find the bearings blown apart and in tiny pieces. We ordered new ones and also found that when the new ones arrived they came with a tube of grease and a sealer to use so water would not get in later and cause more problems. Funny there was no sealer on the original bearings.Next the lid lock finally failed, ordered a new one but did NOT install it back into the machine, now it sits beside the machine. In case it fails again we will have total access to the laundry this time. Finally the UL error code keeps coming up. I refuse to put any more money into this machine again so I am allowing hubby to fix it if he chooses, whichever way he wants as long as no money is involved. So right now we have bungee cords holding the suspension rods tight to help with the uneven load code coming up all the time. Personal thoughts - DO NOT BUY WHIRLPOOL washer/dryers. They are crap and the company just does not care and they try to lie their way out of repairs if people have not done their homework.

I purchased a gas hot water heater from Whirlpool. I have had problems with it since it was new. Whirlpool kept sending repair parts, which I installed, until the warranty expired. Now they say “Sorry Charlie, the warranty has expired.” The water heater has never been fixed. They just dragged it along until the warranty expired. Whirlpool has no complaint department or the repair place will not give it to you. They told me there would be no use for a complaint department. They would just tell the same thing the repair was telling me.

My son bought a Mastermind 250-L refrigerator on 09.09.2009 (invoice no. **) from the Good Morning store in Alleppey (phone no. 0477-23253809). The cooling effect was lost with a loud sound. I requested customer care. Three times, four people came and they gave a receipt of RS 890. After they left, it is in the same condition. I requested so many times, but there’s no reaction. Before I could go for legal proceedings, I would like to make you aware of the conditions prevailing in Kerala in sales and services. The young trainees who dont know to repair have broken down the entire system and it is fully collapsed. The franchise office washed their hands. This will spoil the entire name and fame of the company. Kindly look in to the matter and do the needful immediately.

I love my Whirlpool refrigerator, its great. I have not had any major issues with this brand. I only wish that the freezer was made a little different. Im not a big fan of the side-by-side doors. I would much rather have the one with the freezer at the bottom and the fridge at the top...

First, I was put on hold by the first female for 44 minutes, and then a second woman finally answered, and said she didnt know why she would send me to her, because she was in the sales department, and she put me on hold for another 25 minutes. I finally had to go, because I had an appointment. When I got home, I called back, and got a man by the name of John, and at least he recommended he could schedule a repairman. The problem I told him is, the inside wall of my refrigerator has 2 cracks on the side, and a crack on the back wall. I dont want a repairman to come, just to tell me he cant put 2 new walls inside of my refrigerator. I could not find an email, so I could email Whirlpool about this problem, and definitely, they were of no help. I bought the refrigerator at Lowes late 2003. I have never, in my life, seen the inside walls of a fridge do this. I spent a lot of money for this, for it to crack on the inside walls. It does not seem like something is right with this.

I purchased the Whirlpool washer and dryer three years ago and I absolutely wish that I hadnt. After three years of use, the bearings on the tub are shot. I need to replace them but it will cost $400.00 to repair. This is the second time that this machine is for repair. I am going to dispose this machine and purchase a new model other than Whirlpool. The overall performance is poor and not as advertised. It does not use enough water and does not wash clothes well enough. At times, you can see that the water never reached parts of the garments. I am totally disappointed in its value and quality.

Ill be just as responsible as Whirlpool and Nasons has been... I bought my Whirlpool stove less than 2 yrs ago from a reputable business in a nearby community, CROWN POINT, INDIANA! I have had trouble w/ the burner knobs ever since I bought it...just brushing up against them turns them on. Enough gas escapes into the kitchen... I bought knob covers to prevent that (they did NOT work)! So I called the place I bought the stove from and they sent out a repairman...he said there was no fix for it... but that I owed him $69.99 for the service call. And every time I turn the oven on to heat it to bake something you smell gas also... Im almost afraid to use it... 3 nights ago I woke up to the kitchen filled w/ gas...knob covers on but still one was still on a bit... it was a whopping -25 and we had to open windows to clear out the gas... you shouldnt have to check the knobs once youve turned them off. Nor should they come on when you brush by them...when youre not even cooking... Granted I am short but the serviceman said I should move everything I needed to cook w/ closer to me so I didnt have to brush up against the stove... what????? I have cabinets above and all around the stove. What I cant use those cabinets????? Something is terribly wrong w/ the stove and the service... If youre in the market for a new stove, dont buy a Whirlpool and for certain DONT buy anything from NASONS appliances in Crown Point Indiana... They along with whirlpool dont stand behind their product... They told me they never had that complaint before. WRONG, I read it more than once on this site...liars all of them!

Bought the Cabrio washer dryer set back on 1-12-13 for my new home and thought it was a good purchase. Well now its March on 2017 and the washer has been slowly getting louder during spin cycle to the point where yup you guessed it the bearing is bad because on a cheap seal that suppose to keep water out. It just cost me just under $600 to get the repair done and from reading other reviews and the fact that I have worked on cars and machines at my employment this will happen again. I wanted to save money on water for the city that I live in charges gold prices per cubic units of water but for the price of repairs to the water saved I am in the red. So once it goes again going back to conventional unit and will never buy anything from this company again. I work in the second largest printing company in the world for 28 years on press and know a bit about quality workmanship. Its really sort of typical on how over the years some good manufacturers cut quality and design in planned obsolescence into their product just to make money for the useless corporate bloat that has taken over. I made the mistake in buying what I thought was a good product from a great company but they just proved me wrong. People do not buy any products from this manufacture and find out what other unit they make and steer away from them too.

In August 2012 I purchased a side-by-side fridge with indoor water/ice dispenser. The appliance was purchased from Sears and delivered and installed by their employees or contractors. In November 2014 the refrigerator abruptly stopped making ice and began continuously cycling through the ice making process without creating ice cubes. Repairman told me the ice maker needs to be replaced for $300. He stated the control board went bad and the only recourse is an out of pocket replacement of the entire ice maker. A two year old fridge. The fridge has never been moved, abused, misused or dirty. It has only been used in a two adult home under normal household conditions. I would have thought an item that cost $1000 would last longer than two years!

Cabrio Platinum Washing Machine - We received this washer and dryer set as a gift so I cant complain on the cost. However, it does NOT clean your clothes. Water smells at the start of each load, clothes are left with soap scum and several clothes have been ruined by oil stains!

Whirlpool Cabrio 8kg washing machine - Purchased this washing machine because of the size, water efficiency, no agitator. Have purchased Whirlpool products before and havent had a problem but this washing machine is absolutely a piece of garbage. At first our water bill was hugely excessive so tested the machine and it was using 269 litres per wash when it was only supposed to use 98 litre as stated on the machine. When doing 2 washes a day you can imagine the water bill we had. Lint on washing, continually out of balance no matter how much was in the wash. Had it fixed under warranty then just out of warranty. Water wouldnt turn off. Had to turn it on and off at the top lid. Could now be opened during washing cycle. Started turning itself on in the middle of the night and day. Had to unplug it to stop it, wont spin out clothes. Still sodden. After cycle finished with the lid open it would start to fill up with water again and going out of balance again. Had the appliance people out for the 4th time. Had to have the motherboard and a valve replaced. Its still leaving lint. Washing is not even getting wet so it cant possibly be cleaned. Contacted warranty people. They came out and said it is running as it should be but they advised us this is a common problem with this brand of washing machine. Personally I wish I could throw it away if I had another $900 to waste on another machine.

My Whirlpool has been in use about three years. It was purchased on sale at a very reasonable price. My only complaint is the heat dry function which somewhat fulfills its purpose, but I usually have to hand dry some dishes. Overall, it is an average dishwasher that gets the job done. The best feature is that it is very quiet; you barely notice that it is running.

The only reason I am giving it one star is because it looks good in my kitchen. This dishwasher does not clean the dishes. I’ve had it serviced twice, both having to wait for parts, I am very disappointed. Having to run the dishwasher two times to find myself hand washing... Is annoying. Dissatisfied. I don’t put certain dishes in and run very scant loads. Family of six is not happy!

Purchased a Whirlpool Cabrio 4 years ago. It worked fine until last October when I had to call a Repair Service as all the Digital Controls would not work. It was the Digital Board had to be replaced at a cost of $ 315.00. That was October 2016 and in October of this year 2017 it started doing the same thing again. I call the Repair Service and they told me not to waste any more money on this machine as it is a piece of junk. I guess he was right as when I read all the bad reviews it got today, I realize I will be better off to buy another machine. It will not be a Whirlpool product. I purchased a Sears Kenmore Washer & Dryer back in 1995 and the washer lasted 20 years and I still have the dryer. This is what you refer to as a good product.

Freezer froze up and water runs into refrigerator part. I am 80 years old and have never had any problems with any of my ref (except ice makers) before, but I have never owned a Whirlpool ref before. We have purchased Sears chest type deep freezers without any problems and have been very satisfied with freezers. This frig/freezer is a real bummer.

I bought this Whirlpool America dishwasher because it was cheap. Even though Im Canadian, I like patriotism and I could get behind the American flag logo on the washer. Let me just say, if you like when food comes off your plates, and attaches to your cups, then this is the dishwasher for you. It is always a surprise when you open the door to discover which dishes have been cleaned, and which dishes have inherited the food particles from the now clean dishes. This appliance really helps you work on time management as you are required to wash all your dishes before you put them into the dishwasher. 0/10 would not recommend for anyone who wants clean dishes.

I purchased a 30 gallon gas hot water heater from Lowes in 2013. Within the first 3 months, it went out. I contacted whirlpool who troubleshot the heater 4 different times. Final contact was in early 2014, I requested a tech to look at the heater. Was informed it is now over a year old, it would be at my cost. Replacement parts $30. Shipping the water heater is great if you like cold showers. After a little searching, I find they know this water heater is junk as does Lowes but dont care.

They stink. Major issues with most all of these Whirlpool water heaters. I have had issues with 3 different units. I own properties and these are pure junk. Cant find parts and have to pay for shipping on warranty parts! 2 years old units junked, Ridiculous... never buy Whirlpool!

Microwave did not last one year and magnetometer blew up. Customer service would not honor request to help with purchase. Repair call was more than a new microwave. In essence, I would not purchase this manufacturers appliances.

I bought a Whirlpool gas stove (WFG745H0FS1) 2/1/18. The front control knobs (W11122880) position ink began rubbing off after a year. I sent them pics, their solution was to pay $45 each for new knobs.

We wanted the ease of use and longevity of a top loader WITHOUT a full touch screen. Whirlpool has such units in a choice of price levels to accommodate most everybody. The agitator free design and automatic water level feature is amazing. Clothes are nice and clean and uses about the same amount of water as flushing a toilet.

Cabrio (h2low system) top load washer ..USA 120 volt - A true piece of crap... Bought 2010... Even when it does work, 5% of any load will NOT spin out... The damn thing will refill its tub with rinse water to redistribute load so as to get a spin out. SOMETIME month ago, thing just dies... nothing. Technician comes out for two hours its the shift sensor. Replace for 200+ bucks... done. Works for three weeks, dies, tech is back. 4 hrs... its a bad processor board. Ordered 140$ rebuild, comes in mail few days later. Tech is back, replaces board. We have smoke!! Looks like a bad motor part. I could go on... but why. Never ever buy one of these sorry pieces of dreck. Absolutely the worst. Poor quality even when it works. Horrible wash quality. Never again Cabrio. Remember it.

We purchased a Whirlpool Accubake Drop-in Stove (Model # RS675PXG015) on 10/21/2006 from Lowes Companies, which cost $1,100.00. In 11/2012, we had an error message E1-F2, and we tried everything to get it to clear - all suggestions given by electrical repairman who does repair for Lowes Cos. The stove is porcelain, which also has problems of staining that cant be cleaned. We were told the repair would cost $200 for the panel, and if that doesnt work, another $400 for the other panel. In reviewing other complaints for this Whirlpool stove, there are enough complaints to recall this item or at least give deep cuts for the parts to repair this stove. We have purchased other Whirlpool items, and this one is not well made and too costly to repair. It should last at least 15 years or more. Cant Whirlpool do something about this obvious problem?

We have owned the Whirlpool Quiet Partner II for about 2.5 years. We purchased this from our local Lowes store (on sale). For the first few months, everything was fine. Then, the dishwasher stopped completing a full cycle and left the dishes somewhat dirty. I found online that I could reset the controls by pressing heated dry-normal-heated dry-normal quickly.When the cycle starts, I press cancel and then set the cycle I want and it will do it correctly. I do this every time I wash the dishes since I dont know when it will decide to stop working (wasting water and soap to redo).Now, the dishes are not drying and water collects on the ceiling of the tub. I saw this after a smell was coming from the tub (like mold) and when I looked up at the top of the tub, I saw water droplets hanging there and mold forming around the sprayer and back of tub. I have to wipe the ceiling dry now or just run vinegar through it often. I cant see paying someone to come out since service calls start around $70 just to come to my home. I did look at reviews for the dishwasher before buying but I wished that I had seen this site first. I would not ever recommend this dishwasher to anyone!

Purchased a Whirlpool washer/dryer pair @ least 5 years ago. Great machines. Washer washes very clean. My only beef is that once the cycle starts I cannot open the lid. Dryer will dry almost anything in 10 minutes or less.

I purchase newly Whirlpool washing machine but it was not working from the first day of my purchase. So many service Engineer came but nobody can solve the problem, so I suggest to all please don’t buy washing machine from Whirlpool. I am very disappointed from this company.

My Whirlpool Duet washer was purchased on August 2006. The first one had to be replaced as it flooded my laundry room on the first floor and the basement – not once but twice. When I was told that they would send yet another service person out to try and fix it, I told them it would be at the curb and that I was looking forward to filing a lawsuit. Then after being on hold for forever and getting the company that sold me the unit involved, they replaced the washer at no charge.From day one I hated this washer machine. If you failed to take the clothes out immediately after washing, they would get a musty type odor and I never felt the clothes got cleaned enough. Yesterday, I went to empty a load of laundry and it was soaking wet with water pooling in the bottom of the barrel. Today, I had a certified Whirlpool tech come and look at the washer and he told me to put it at the curb as the rear bearing is shot and needed to be replaced. He also told me not to buy another front loader and the cost of the repair would be approximately $800.Thank you to Whirlpool for manufacturing a true hunk of crap that, may I say, cost me $1300. I will make sure I tell everyone I know that your products are crap and I would rather wash my clothes by hand. I did call the WP customer service number and was told that this is unheard of and that these machines rarely have any problems. After just reading multiple complaints of the exact same problem, I now know that this product is inferior and the design of the bearing assembly is seriously flawed. A major recall is probably in the near future and Whirlpool is hoping that most people will just dump them before the recall is made public.

Piece of crap! Approximately 18 months of aggravation. Clothes don’t come clean, leaves residue on them. Just absolutely the worst experience I have had in six plus decades of doing laundry. When next I get a washer...it won’t be a Whirlpool or anything made by the company. There should be recalls on these washers.

We purchased a Whirlpool French Door Refrigerator in December 2016. About 3 months later the back panel was frozen preventing it to cool. We unplugged it and called customer service. They sent out a repairman, but by then it had thawed out. He told me he couldnt fix what he couldnt see, but he didnt even check it out. Two months later it did the same thing. Then he said I must have left the door open. He made me look stupid. During that year he came out 4 times until he finally changed all parts. We kept telling customer service we wanted a new one. After going back and forth with them they finally are reimbursing us, but they charged us $300.00 because we didnt want another Whirlpool product... now we found out they have the worst ratings and we certainly had a very bad experience not to mention all the food I had to throw out because of it. They did not care at all. So please do not purchase any Whirlpool products. I would not recommend that product to anyone.

I have had my Maytag (Whirlpool) Centennial Commercial machine for 10 years and it has not required any repairs or have given me any issues. I love the water level sensor that doesnt require me to select a load size. I would highly recommend the Whirlpool brand to consumers.

The washer was 5 months old and broke. Three service appointments and multiple phone calls, it still wasn’t fixed. Whirlpool sent rusty parts out to my home and that was the second excuse for not fixing the washer. The poor service guy must have been 70 years old. Hello, how do washer parts get rusty when they are not even used and are kept in a box?

The washing machine continued to display an F1 error code. I contacted the manufacturer and was told that they will not do anything about the problem due to it being out of warranty. This is the first time I have complained about a product or service and want to try and assist anyone who may be thinking of purchasing a washer from Whirlpool. I do not recommend purchase of these units.

We purchased our Whirlpool Refrigerator, oven, and microwave a little more than a year ago. Not a single negative event with any of these products and my wife and I wholeheartedly recommend Whirlpool for operation and last ability, unlike the products we replaced them with.

WARNING: Do not get the warranty plan through Whirlpool if you have stackable washer and dryer, you will have to remove the dryer yourself before they come out to service your appliances. I was willing to pay extra to have them take it down, the contractor said I had to call the extended plan service, yet 6 telephone numbers later to include the complaints department to no avail... Whirlpool contracts out so get your own and you may save a few dollars!

Whirlpool Cabrio Top Load, Short Agitator to protect clothing, cost reasonable, on sale $800.00 both (Aug. 2013) - Sears credit no interest. Moved, and had to sell after a year, but I anticipated a long life r/t rating/reviews online. One Problem: no setting to soak clothing that may need it. I bought the largest Whirlpool Cabrio to make sure my Queen bedspread (heavy blanket type fur on one side) would fit. Because of the short agitator I could have bought the smaller one I discovered. I could fit 6 regular side and 4 beach heavy beach size towels in it easily, or two Queen quilts in at a time. I rarely needed an Xlg water setting. The dryer had a steam only setting but I never tried it because it was set up in the apartment when I arrived and the delivery people were not very bright. Put the Dryer farthest from the vent, washer farthest from faucets, and put hot and cold hoses on opposite spigots. I did not want to chance they set up the steam section wrong, as well. I moved across country 1 year later, but have trust the W/D would do well. My last Sears brand (made by Whirlpool) only had one minor problem (on warranty) and lasted a good 8-10 years before moving and selling them to another couple. They were still in wonderful working order (front loader).

Reliability. I have bought Whirlpool used and new and they have been the best washers that last so much longer than other brands. They also have more than enough settings to truly take care of everything in your home that can be washed.

Ive owned my Whirlpool appliances for almost a year. So far Ive had 4 maintenance calls for my dishwasher to be fixed (over and over) and once for my refrigerator. Yes, its currently under warranty, but Im afraid to keep it without an extended warranty due to all the issues Ive had with them. So, now Im going to be spending hundreds on an extended warranty. I will never buy another Whirlpool.

I have purchased a Whirlpool Water Heater on May 21, 2005 from Lowes Model number FG1F4040S3NOV, Product number 0730261, Serial number 05181291061. It is one of the Flame Lock heaters that was part of a class action law suit. The lawsuit has been settled however. I have had three thermocouples to date installed and each time the heater has gone out after three to four days. The technicians I have contacted at Whirlpool all have stated something else is wrong with the heater even knowing that this model has been seriously defective from the beginning. They always tell me to do this and that to repair it. I do not have hot water as of the date of this writing. The original problem began June 19, 2011.

My Whirlpool stove and oven have been absolutely wonderful. My Appliance is 18 years old and Ive never had a problem with it since the day I bought it. I recommend Whirlpool appliances for the whole house.

Home is new construction. Moved into our home in May 2015. All appliances are Whirlpool. The Microwave (model WMH32519CS-1) stopped heating in September 2015, service tech replaced the tube and capacitor. Microwave stopped heating again on Nov 16, 2015. Service tech notified again. Each time it takes 3+ days to get the service tech to look at the oven. This will be the 3rd Magnetron Tube in 6 months. This should not be happening. Contacted Whirlpool direct, asked if we could get the entire oven replaced with a new one. I was informed that this was not a company policy. It was a real waste of time talking to customer service. They are clueless and could care less about what is happening with our oven. I have had microwave ovens for years and have never had this kind of issue. Whirlpool has a real problem here.

Purchased 9/23/2013 on 5/20/2014 no hot water. Called Whirlpool, unit has a 6 yr warranty. Brian advised me no one close to our area to service. He told me to contact a local plumber, they would pay for parts and $75.00 in labor. I attempted a couple of calls and could not find a plumber that was willing to come out and let us pay just the difference, after parts and $75.00 in labor and them bill Whirlpool for the remainder. They wanted between $225.00 and $300.00 plus parts. Lowes where we purchased the water heater told me to call Whirlpool back and get an RA# and they would be happy to exchange the water heater. I called Whirlpool and they (Leigh) refused but did say they would pay 200.00 in labor plus the cost of parts. The unit was only $231.23, but they would rather pay upwards of $300.00 than just let us get a new one. I asked Leigh if this made sense to her, she said it did. I guess Im just ignorant because it doesnt make sense to me. Whirlpool COULD NOT even find a plumber that would come out to our small town to do repairs under their OUTSTANDING WARRANTY. I have laughed at these people and cried over this whole situation. I can honestly say I will NEVER buy another Whirlpool product and will let everyone I know and even some I dont know (lol) how horrible this experience has been.

I purchased this washer 4.5 years ago. I have always been a Whirlpool customer. My parents had Whirlpool washer and dryer while I was growing up in the 60s. When I got married in 1976 I bought a Whirlpool washer, dryer and refrigerator. They lasted 19 years!!! Then I replaced all 3 in 1995. Again, lasted 16 years. I gave the washer and dryer to my sons when they moved out--its still working.So I thought I would reward myself with a new Whirlpool washer and dryer in August 2011. I didnt know about the pitfalls with the high efficiency washers. The dryer is great, but I HATE my washer! The lid lock is ridiculous, we should be given an option to override it. The sensing takes forever. The low water level leaves clothes unclean, and with detergent residue, causing the need for another rinse cycle. This saves no water if you have to run it twice. Not to mention how long it takes to do a load. Then it doesnt spin all the water out and you have to run a spin cycle. It aggravates me every time I do laundry. After being a Whirlpool customer for over 35 years, its time to move on. I just ordered a GE machine that is old school, no sensors, no lid lock, and I can control the level of water. Whirlpool doesnt make these simple machines anymore. Youre going to lose a lot of customers if you keep selling the trash. This is the worse washer I have ever had. My adult son went into a rage last night trying to use it, he forced the lid open and broke the lock, and of course it wont work at all without the lock. Good thing I ordered the GE washer the day before, it will be here in a few days. Cant wait to bash the Whirlpool with a sledge hammer, it will give us great satisfaction! Are you listening Whirlpool? Your designers need to go back to the drawing board. I realize this is not just a Whirlpool problem. Ive seen complaints about kenmore and every other manufacturer that makes these stupid low water sensing machines with lock lids. If consumers are too stupid to keep their kids out of the washing machine, maybe they should have their kids taken away.

In 2007 and 2008, I purchased 7 natural gas heaters: 1 for my home and 6 for rental properties. I have had nothing but problems from all of them. Two of them failed this weekend (one 40-gallon and one 50-gallon). I called the 800 number and have to pay $63.50 for parts for the 40-gallon and was given a PO number to pick up parts for the 50-gallon at Lowes. They do not have the parts. I have spent over $250,000 at Lowes since 2000. I have all Whirlpool appliances in rentals and my own home. The discussion I had at two Lowes stores today really showed me how they take care of their customers. I told both stores that I will never buy the Whirlpool brand again!

May 4 I ordered a washer and it was to be delivered on the 21st and on the 20th a salesperson calls me to say my ordered washer is out of stock and she gives me a substitution washer that wont ship to me until june 20th a month away even though I already had been waiting a month, I was very upset and said, I wont accept it but let me think about it, I thought there must not be anything sooner (BIG MISTAKE). So I called back and accepted but after getting off the phone looked online and found a washer that would be delivered on May 28th and it was just delivered no problem but now no one at WHIRLPOOL can find the subbed order to cancel and give me my refund from the out of stock washer... So I have paid for 2 washers and every time I try to get help I have an hour wait to get a person. I am a 65 yr old woman who has been put thru so much stress and it is not good for my health. All I want to do is cry.

We purchased the Whirlpool double oven with convection to go into our new home 18 months ago. I used the self-cleaning cycle on the bottom oven for the first time last weekend. Halfway through the cycle the control panel went blank. Basically both ovens died, and the bottom oven door is locked. After researching online I learned that this has been an issue with the self-cleaning feature on Whirlpool ovens for some time now. So buyer beware, if you decide to purchase, dont use the self-cleaning feature.

Bought the Cabrio washer in March 2011. Have had the same problems as everyone else. The machine is constantly off-kilter, does not wash well due to lack of water. Sounds like a freight train when spinning. Bulky clothes dont drain properly and have to be rinsed and drained a second time. After one year of ownership, the entire control panel had to be replaced. The next year, the same control panel had to be replaced again plus a water valve had to be replaced. Thank God I bought the extended warranty. The repairs would have cost me $1000, more than I paid for the washer in 2011. Total piece of junk. AVOID AT ALL COST!!!!

We purchased this dishwasher in June 2014 while putting home back together following fading of our home. Within 6 months of purchase the dishwasher was doing dry washes, and getting very hot touch. Whirlpool sent out repairman who replaced parts that had melted inside dishwasher and the control panel. This same thing happened 2 more times. A repairman came and repaired and replaced parts. In May 2016 it once again was running so hot that it burned hand when opened. Once again repaired but this time it started leaking from front dishwasher. When we talked to whirlpool they sent out repairman and assured us they would pay for any and all damage it had caused. They also replaced dishwasher with Maytag of our choice which they covered all cost. When installers pulled out the unit we learned the dishwasher had most likely been leaking the entire time, water damage up entire wall, cabinets ruined, countertops had been bubbling and separating from wall, floors ruined. We followed all instructions and had three contractors come to do estimates that were from 27,500-30,680. Whirlpool then sent outside adjuster because of cost. We have now received offer of 6700 and told we could take this or submit to our insurance company. Also we now have Mold in kitchen which they are aware of and we think the flooring is now rotting and breaking.

MODELGR673LXOQ WHIRLPOOL RANGE - I purchased this range in January 2014. It is a good-looking range with a ceramic top and a convection oven. It has burned more food in a year than I had burned in several years. The top burners get red hot no matter where you have them set. They turn on very hot, then turn off and after a while they are red hot again. Cooking anything that requires a medium or less heat burns to the pan bottom. The oven works alright as a regular oven but when put on convection it burns the food closest to the fan before the rest is cooked. The company sent a technician to check the stove. He checked the temperature of the oven and said it was running too hot. He changed that setting and the first time I tried to bake it took forever. I reset the oven back to where it had been. The tech made no attempt to check the top burners as he said they couldnt all be bad. I hate this stove I had my former stove for thirty years and never had problems with it.

I purchased model #GI7FVCXWY01, SERIAL #KY4234335, and it arrived in Jan 2010. It is now going in the trash! Two repair companies came out and both told me the ice maker had issued a recall, but in reality, Whirlpool told me to buy the replacement part for $348.73 to fix their poor design! I called the 1-866-698-2538 customer service and so sorry is all you get! By the way, neither of the repair were willing to install the replacement part, as it takes too long to install and these compressors are never the same after the ice maker has these issues! Both repairmen said to trash the refrigerator. How sad that a $2500 refrigerator only last from Jan 2010 until June 1, 2014!!! I will never buy a Whirlpool anything!

Bought microwave two years ago, almost immediately when stove area got warm, the microwave would not work properly. It would beep, the info keypad would cycle, then freeze up. After unplugging and letting it sit for a while, it would work fine for a time. Now it doesnt work properly at all. We keep it unplugged until we need it then it may or may not work. I have had a service company look at it and the only thing they could figure was that was an electronic failure from the heat. I am concerned that it is a fire hazard and leave it unplugged. Not what I expected from a $1000 appliance. I wish there was a class action suit that I could join.

Purchased a GGE388LXS04 electric range in June of 2013 from Lowes. In September 2013 one of the top burners went out, under warranty Whirlpool repaired the burner. Now after attempting to use the self cleaning mode for the oven, the ovens (top and bottom) along with warmer device do not work at all. This issue is evidently a major issue with Whirlpools electric ovens. Will call Whirlpool tomorrow as the oven is still under warranty, will also call Lowes and see if they will replace the oven with an oven with a comparable brand. Wish I had read this site before we purchased this oven. A very bad experience.

Whirlpool Cabrio Washer and Dryer - The washer does not stay balanced even with a very small load (even though advertised can wash King size comforter). Even with a light load, we have to put the dryer on Heavy Duty or Bulky...and usually have to dry a second time. When attempted to contact Whirlpool, no help available. WORST PRODUCT I HAVE EVER PURCHASED... Would not even want to GIVE this set to a friend or family member. DO NOT PURCHASE THIS PRODUCT.

The machine is two years old. It cost over $1,000 to buy. From the beginning, we have had mold issues with the machine. The entire house fills with the smell of rotten eggs every time we use it. The machine is used daily so it doesnt sit for long periods. Despite all the complaints online about their machines, Whirlpool refused to acknowledge that there is a design problem with the machine. They refused to make any repairs or buy the machine back and their only suggestion was to buy more chemicals from them to use to clean the machine. We have done this in the past to no avail. Oh, they did offer to send out a service company but on my dime. Whirlpool needs to be sued and I only wish that someone would start a class action suit against them. It really stinks when you try and do the right thing and buy American only to have the company not give a crap about their customers or the fact that their product is garbage. About 10 years ago, I had a Maytag front loader washing machine with the same problem. Maytag bought the machine back on a pro-rated basis, no problem, no question. Of course, Maytag is now owned by Whirlpool. Too bad they didnt adopt Maytags customer service policy. I cant wait for them to go out of business - something they deserve.

Whirlpool Cabrio - This washer and dryer have been garbage since the beginning. It does not clean soiled clothes and the dryer (gas) has always taken forever to dry a load. I have always had GE prior to this. I will never purchase another Whirlpool product again. We even purchased the extended warranty and the repair guy was out yet again and said it is not repairable. Now we are without a washer for 5+ days and its going to be reviewed. Review? I want my money back. Theres a lemon law for cars, there should be one for these machines.

I have bought what I thought my dream washer and would never need to buy another one. I told people about it and could have sold many of them. That was in my first year. Now I am into our second year with them and it quits. It cost right at 500.00 and when I called Sears, the company I bought it from, they charged me a service call and says it will be $585.00 to fix. WHAT? This is a lemon. If I were to buy a car and have this sort of problem they would warranty it. Why not appliances? This is an outrage. This should be illegal to sell.

We have a Whirlpool double oven that is about 3 years old. Today we used the oven for lunch and about 2 hours later we heard a loud sound from the kitchen. When I went to see what had happened I found glass shards all over the kitchen, some as far as 10-12 feet away. The outside glass of the top oven was spider-webbed and had apparently exploded. Nothing had come into contact with the oven and nobody had been in the room with it for over an hour, it just randomly exploded. I am going to contact Whirlpool but judging by the other posts I dont expect much help from them.

My washer and dryer have been a great experience. Doing laundry has never been my favorite chore but these energy efficient and state of the art machines live up to their advertising. One of the best things I like about the washer is the ability to set the run time for a future time. I do wish the dryer had something similar.

Shortly after the warranty expired my refrigerator started building ice on the floor of the freezer. With the build-up of ice the freezer started leaking on the bottom. Sometimes it gets so bad I have a hard time closing the freezer door properly. The Model# GB9FHDXWS06, Serial# K31505096 of my Whirlpool refrigerator. I do not recommend any Whirlpool product. Do your research before you buy any Whirlpool product.

I purchased Whirlpool washer in 12/2011. Immediately, I noticed the noise and called service. It was a whistling noise. The clerk told me nothing was in the manual and it would cost $65 to have a tech come out. He advised me to wait until it was louder and more consistent. I called again when it was. Gear case was replaced on 5/2/2012 five months after purchasing the machine. I called Whirlpool again in 5/2013 - same problem. I was told the diagnostic call would be $95, labor which is extended for a major job is $85 and the part would be $290. It would cost $470 to repair as the gear case was guaranteed for only three months. This machine is a lemon since the gear case is now shot again prior to the machine being 1-1/2 yrs. old. I called Whirlpool and spoke to Amy (Esc. Sup.) who advised they would replace the part only. The appointment was scheduled; the tech came, did diagnostics reading a manual and said the gear case is shot. I inquired, Well, you are going to fix it today right? The reply was, Oh no, it has to be ordered and its a two-man job. When I arranged for this appointment, this was clearly explained and what I was expecting, two men and the part to be replaced with them. Now its a five-day wait to get the part and then a scheduling issue when they could do it. This machine is a lemon and Id like to have the machine replaced or my money refunded. This is a runaround, scheduling the appointment and having someone show up with the manual and having no parts and not knowing that it was the part which broke again from previously being replaced.

I just bought a Whirlpool Gas Range from Home Depot on 11/11/2014 and I am having problems with the oven. It is still under warranty and have five year protection plan. I called to have the problem fixed. Two technicians and the oven still doesnt work.

Whirlpool Cabrio Washer WTW7340XW sounds like a small jet during spin cycle. The Whirlpool Cabrio Washers have a very well known and well documented problem with the tub bearings failing. Many many disgruntled owners have posted their complaints online, and there are many videos showing the issue on youtube. This issue is so prevalent that the manufacturer has created a tub bearing failure repair kit for $350. The repair is so expensive and labor intensive that many of the certified Whirlpool repair shops no longer work on the Cabrio washer stating that a better washer can be purchased for the cost of this repair.That said, the manufacturers customer service group denies that the Cabrio tub bearing failures is a common problem and are quick to state that Whirlpool holds no liability for this problem. Ramping the complaint up to a customer service supervisor is met with the same canned response. Regardless of the thousands of complaints Whirlpool is claiming that it is normal wear and tear for the tub bearings to fail. The manufacturer should recall the units for this manufacturing defect in the Cabrio design.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

Unfortunately, I can not rate this machine LESS than one star. I would rate it ZERO. We purchased the Whirlpool Cabrio washing machine model WTW7800XW0, 2 1/2 years ago in 2011. Since that time, we have had nothing but trouble from this machine. The machine basket gets off center when you have heavy items in there like jeans or a large load of towels and just stops working until you raise the lid and even out the clothing in the basket. If you wash something like a throw or a set of sheets in it, they get all twisted and wrapped around the thing in the center and end up in a big mound. We have had the glass top lid replaced on this machine TWO times over the last 2 years because the plastic frame on the lid around the glass cracked and broke and became warped in a raised position. This caused the machine to stop working because the machine will not wash clothing unless the door is locked down, and the door cant lock if the lid is cracked and warped and broken. So you have to set something heavy on top of the lid to get the lid to lock so you can wash a load of clothing! TWO times we have had repair people out to our home to replace the lid and now the lid is cracked and broken again, for the THIRD time! This is THREE broken lids in just over 2 years. Unacceptable!! The hinges on the lid that attach the lid to the machine are also rusted. This rusting has happened on all the lids that we have had replaced in the last 2 years. I will never, NEVER purchase another Whirlpool product again, EVER. Their products are inferior quality and JUNK. We have the Whirlpool dryer also to match the junk washing machine and the quality is just as bad but we are living with it because we have no choice right now. It takes 2 hours to get a load of clothing dry and forget drying jeans or towels; it takes forever! Whirlpool makes a dreadful product and their customer service is even more dreadful. =(

Bought this washer 5 days ago!!!! Broke after 4 loads of laundry. Store manager says they will deliver new washer. ERROR CODE LD LONG DRAIN and heavy duty humming sound. Unplugged washer to prevent further damage to washer and reduce risk of electrical fire in home. Consumer affairs wants me to rate my experience - rate my experience on what? Ill give 4 stars dissatisfied here, but field wont let me go more than 2 stars. If its this website they want me to rate I give 2 stars dissatisfied, as for the washer, dole out 7 Benjamins for a product that dont work and you tell me!

I have always used Whirlpool products and have grown up with them. From washing machines to dishwashers. Not only is it made in the USA but its reliable. The only problem is space and it can do with more freezer space. Other than that its a great refrigerator.

If everyone would submit their complains to Whirlpool, they might do something about this. Submit your complaint to ALL of the followings emails: investor_relations@whirlpool.com media@whirlpool.com whirlpool_customerexperience@whirlpool.com B2Bdevelopment@whirlpool.com. Here is what I wrote to Whirlpool: Model: WTW7800XWO, Serial number: C02670320. I purchased the 4.6 Cu. Ft. Cabrio Platinum Top Load Washer in June 2010. The washer lid has broken 3 times now. Its snapping by the hinges. I have been charged about $300 per lid. I believe the hinges are not durable enough to support the weight of the glass lid. I have read hundreds of reviews regarding the same model and issues, I also have a friend who has the same model and is experiencing the same issues and has had to replace the lid twice now. Im disappointed that Whirlpool has not taken accountability for this and either issue a recall or replace the lid at no charge to the customer. If there has been so many complaints, why hasnt Whirlpool taken action on this? I am requesting that the Whirlpool Headquarters address this issue immediately.When I called customer service to complain about this issue, the rep informed me that they have never heard about this issue before. From all the reviews I have read online, it seems that customer service is telling them the same thing. By not addressing this defect, Whirlpool will lose thousands of customers. This is not the way to retain or have returning customers. This is the first time I have purchased a Whirlpool appliance. I will not be a returning customer if this matter is not resolved.

Was weary due to not a name associated with furnaces, but we installed a 100,000 Btu unit 2 stage and have not had any issues thus far.

I have been unhappy with my Whirlpool Cabrio washer since I purchased it from Lowes. I should have looked online before I bought it and then I would not have made the mistake of buying it. The washer leaves soap deposits on the clothes and sometimes leaves a colored soil. It has ruined numerous clothing by tearing out hems of towels and wash cloths and tore a hole in a favorite sweater. I prefer an agitator in my washer. From what I read, I will soon begin to have other major problems and then I will replace it, but not with a Whirlpool.

I had purchased a washing machine trough CSD canteen and go for AMC for five years on September 25, 2006. In September 2010, I lodged a complaint and the Engineer visited and asked for a replacement of the bottom cover. I said okay, but later on he told me that I have to replace the complete outer cover. I agreed and asked them to replace it. The cost is fixed for 2,500Rs. They replaced the cover but did not replace the bottom cover.I talked to the agency and they agreed to hold to 1,000Rs for the bottom cover and I paid to them 1,500Rs. Later they brought an old cover and I refused to replace that. They told that the bottom cover is not available. Then they never tried to replace the bottom cover. I arranged for the same from the local marketing for 600Rs and replaced it. I paid the service charge for the engineer.Later, I lodged a complaint that the machine was not drying the cloth. The engineer visited and told me that the belt will be replaced on payment. I agreed and he told me that I will visit the next day and replaced the belt. But he did not come until it was late.On September 18, 2011, with number DL0911018283, my machine was not switching on and I lodged a complaint to customer care. But no engineer visited me. Then I regularly complained but there was no response from the agency. On September 23, I talked to customer care, Mr. **, that I am going out of station and I lodged a complaint from the last five days that no engineer visited me. My AMC is expiring on September 25, 2011. I will come back on October and then send the engineer. On October 9, I reminded them that they refresh my complaint with number DL1011007031. The engineer visited and told me that the PCB of the machine is faulty and I have to pay 3,500Rs.I told him that I complained for this problem during the AMC period, hence they are supposed to repair my machine free of cost but he refused. I talked to customer care and tried to resolve the issue but I was not successful. Then I talked to Mr. **, the head of Customer care in Delhi, on October 12. He promised to resolve the issue but no engineer visited me and my machine is still defective. On October 13, I tried to contact Mr. ** several times but he or his PA is not picking up the phone. Now, how will I get to repair my machine?

We purchased this washer (Whirlpool Cabrio) about two months ago and we have been extremely dissatisfied with its performance. Quite simply, it does not get clothes or anything else clean! I have tried every possible setting and still the dirt remains on anything that is even slightly soiled. So, I cant believe that things that dont look dirty are getting cleaned either. They probably arent even getting rinsed, even with the extra rinse option. It seems almost nobody likes this machine, so why is Whirlpool risking their formerly sterling company reputation by keeping it on the market? I would be happy if I could return it to the store for a refund, but that is not a possibility as far as I can tell. If you are considering buying this machine - dont!

Perhaps I am fortunate, but when I read complaints regarding products on the Consumer Affairs site, it makes me wonder because I never have any problems whatsoever with anything I buy. The only time was with a cheap $20 dvd player which lasted just a year. I was given a 10 year old whirlpool fridge 7 years ago. It still works great. Very cold freezer and great features such as frost free freezer. Also Whirlpool Estate budget line dishwasher, washer and dryer ten years ago. No problems!Why do people spend thousands on refrigerators, washers, dryers, and dishwashers? Just buy the basics. It is not important to buy french door refrigerators, dishwashers with stainless-steel interiors, washers/dryers on pedestals and the like. You are only impressing shallow people. All in all, I will always purchase no-frills Whirlpool appliances. They are the best! And you can be like me and have no credit card bills and plenty of money in the bank with the result of low stress.

Purchased a Whirlpool hot water heater from Lowes. Heater has 6 year warranty. Hot water heater is 1 year old and the pilot would not light. Contacted Whirlpool warranty department to what the failure cause. A new control was sent and replaced by a qualified journeyman plumber; still not working. Called whirlpool warranty department, told control valve must be faulty. We have gone 5 days with no hot water. I am not waiting another 5 days to get hot water. I am having the plumber take out this worthless Whirlpool heater and haul to the scrap metal business. That is where I should have sent it from the get go. Dont purchase a Whirlpool product. The money should be spent on a product that works and will last.

I have spent more money in the last year to fix this piece of crap. So very disappointed!!! I have lost $$ of food because fridge does not cool.. Ice maker is a joke... I am going to call someone out for the 4th time... Costing me a fortune... Very disgusted with this product.

I love this stove! It is nearly perfect. I wish it was easier to clean the glasstop, but I imagine that comes with any glasstop stove. The stove is easy to use, and I love the cooktime option. My only complaint is that the timer is very quiet, and when it is a timer while something is cooking, it only beeps once. If its a timer when nothing is cooking then it will go off repeatedly until you turn off the timer.

We bought the refrigerator end of November 2017 but didnt start using till February 2018. March/April stopped working completely. Since it was on warranty, we got repaired. End of December stopped working completely again. Few days after the warranty expired. We got few Whirlpool products with our order in November. Washer was already repaired too. We will never buy Whirlpool again!

Whirlpool Washing Machine WTW4800XQ4 - This is an expensive piece of garbage. My clothes come out with lint still on them. They do not smell clean and in fact, I wonder if they even are. My blankets come out heavy and soaking wet, so much so that I have to repeat a rinse and drain cycle before I can place into the dryer. The machine is always off balance and its so loud that my almost deaf grandmother who cant hear a thing wants to know what that noise is when shes halfway across the house each time Im doing laundry. Ive called Whirlpool and they have sent a tech out who insisted it was I who did not know how to load a washer and that was causing all of the problems. I found this interesting since I am 37 and never encountered difficulty with a washing machine before. Our visit concluded when he insisted it was user error and went on his way. The next day, the washer was not even cycling, and I phoned whirlpool back. This time, there was a computer problem and there was no arguing about it. The technician came back out reset the internal computer. The machine seemed to run more quietly for about a week, but went right back to its old loud self. The only improvement Ive noted since then is it does not move across the floor now while washing. I wish I never bought this thing and would certainly never recommend it.

Gas control not working. I have replaced the thermostat twice in three years. Now, the hot water tank pilot will not light. The igniter works; a new thermostat has been properly installed, and the pilot will not light. The gas is on, and the tank has functioned. I just want a new gas control.

Owner of 20 apartments, 16 of them have electric water heaters and 4 have natural gas units. Have replaced over the years all 20 water heaters. 19 of them were replaced with Whirlpool units bought at our local Lowes. It is my opinion that they are very unreliable. The tanks rust out in NO time. The electric units last just a little better than the gas units but still terrible. Of the 4 gas units so far I have had to replace 3 of them and the longest one lasted 6 years and 7 months!! One of them was just over 6 years and the other was 9 days away from warranty expiring. They replaced that one. If you have no other choice make sure to buy extended warranty if available. They just dont last!!

I have a model FG1F4034T3NOV water heater that was a problem since day one. The pilot will not stay lit, and apparently, there was some sort of class action lawsuit due to a defective part that I missed out on because I didnt know about it. The telephone representative is quick to point out that it is out of warranty due to the date of manufacture and that it needs about $200 in parts because I cant find the receipt from 4 years ago, when I bought it from Lowes. The company flat out refused to do a courtesy replacement for parts or discount them.

I like the looks with brushed stainless steel and black. The most difficulty was getting someone to help get it and load it. But other than that, Ive had no problems with the dishwasher.

In addition to my refrigerator dying after 3 years, my microwave died after 4.

We have already filed a complaint but could not get any satisfactory reply. Our washing machine is not working properly & we are very angry with your service. It has created a lot of problem to us. Kindly do something regarding this.

This washing machine is awful. It takes twice as long to wash clothes. My older washing machine did clothes in 30 minutes or less. This thing takes over and over stop go, stop go, stop go. Open lid it fills again and removes water, when spinning the lid locks and you cannot open it without unplugging and starting all over again. The wash doesnt even circulate to clean the clothes properly arggghhh. Annoying as all get up. The washer has no control for the water level. The clothes dont have enough water to clean or rinse. I spent over $500 on this and cant get rid of it as most people are selling these on local websites as they hate them as well. Whirlpool thank you for taking my money and producing this junk. Never ever again! I think the seller is also responsible for not telling me what to expect of this junk.

I have always purchased Whirlpool products and when we were hit with a flood I had to purchase a new washer & dryer. Naturally I bought Whirlpool. I have regretted this purchase ever since. I wish I had known about this website before my purchase & been able to read the reviews. This washing machine is the worst appliance I have ever purchased. The clothes get clean SOMETIMES. It takes FOREVER to do a normal size load of wash. I will have to think long and hard before ever buying a Whirlpool appliance again. I cant believe you ever made such an inferior product. You should be ashamed of yourselves for duping the public.

My parents bought a Whirlpool washer machine and the machine was fine for the first two years, then water started leaking from the bottom of the machine and no one has yet to fix the problem! They have the worst customer service department. The A&E worker who came to my parents house smelled, wasted a bunch of time working on the machine and didnt fix anything! The A&E worker visited my parents house over 10 times and the problem still wasnt fixed! They (worker) have ordered parts after parts and still water keeps running from the bottom of the machine! Someone, please help and cut Whirlpool from the stores! Ive spent almost a whole on the phone trying to help out my elderly parents! Its ** and a lot of headache! Never use Whirlpool; theyre all crap!

I called Whirlpool to have my dishwasher and fridge fixed. I knew exactly what was wrong with my fridge. I asked how much it would cost and was told $129.99. I asked why so much. I was told that it included the labor and service charge. I asked if I would need to pay for both units if I did it the same day. She said that the company provided a 30-dollar discount. I decided to only service the fridge at this time. I spent the entire day today, waiting for the service person to come. And when he showed up, I told him that the fridge needed a computer board. He then started telling me that it would cost $200 for labor. I explain that I was told that it should be $129.99 for service call and labor. And he said, No lady, its $70 for the service call and labor is $200. I then called Whirlpool where I spoke to multiple people within a forty-minute call to explain that this is absolutely wrong and that I am not going to pay for the service call. I then spoke to a Niki (3544) who is supposed to be a manager, who basically said my problem now is with the service company, not with Whirlpool and that there is nothing they can do even if they misquoted me. I agreed to pay $129.99 for service and labor, not an $70 service plus labor. I am so upset because I have been a client of Whirlpool for ten years. I have called for service on multiple items in my home, and I have never had a problem. This is so outrageous. I absolutely expect Whirlpool to rectify this mistake. I am also going to report this matter to the BBB and to Fox News. Whirlpool representatives should be able to provide a quote for one thing, and then when the service comes to your home, its a different amount.

In January 2011, we bought several appliances and a refrigerator was one of them. The model number is G15VAXVQ01 which is a side by side, French Door Ref with water and ice on outside. We have had problems with the very cheap plastic drawers that are at the bottom of the refrigerator to hold vegetables and meat. We have to be extremely careful so they will not break when opening the drawers. As of late, the fruit and vegetables have been freezing. I went to change the temperature on the outside gauge and dropped the control to 33 degrees and it stuck there. I tried to unplug the refrigerator to reboot the system, to no avail. The temperature is stuck at 33 degrees which will freeze most of our food in a few hours. The freezer side temperature gauge does work.We also have problems with the ice/water machine. I pushed the water button a week ago and from then on, I couldnt get the ice to come on. I did unplug the refrigerator to reboot and then I was able to switch over to the ice, but I could not get back to the water side. Also, there is no crusher on this machine so the ice comes out in chunks. If we had to do over again, we would not buy a Whirlpool as it appears that they are not interested anymore in quality products and consider cheap junk something to be desired. Not by us! We will get this albatross fixed and see about getting rid of it. It is a buyer beware market so I suggest others beware of Whirlpool products.

19 gallon Electric Whirlpool water heater Model #e1f20us015v - Purchased this water heater from Lowes to provide hot water to small apartment with no kitchen for my son, built in my garage. Had unit professionally installed within 1 foot of bath to provide hot water for shower and sink in bath only. Hot water lasts only 5 to 6 minutes and takes approx. 2 hours to recover. My son cannot even take a normal shower! ntacted Lowes who was unable to help and told me to contact Whirlpool. Contacted Whirlpool after my model number would not even come up on their website. I asked tech what was the normal expected amount of time before hot water depleted. She did not know. I asked what was the normal recovery rate. She did not know. I asked for information on the energy rating. She said there was no information available. I asked how I could receive a refund. She said that they could only send a plumber to check unit and that nothing would be done if it was heating water. I asked to speak with a supervisor. She said none were available and said one would call me. I never received a return call. VERY DISSATISFIED with Whirlpool on this issue. It appears my only recourse is to purchase a new water heater and scrap the present one.

We purchased our washing machine on October 12, 2011 from Lowes. Our washing machine broke on 04/19/12. We have been dealing with Whirlpool and Advanced since 04/23/12, trying to have our machine repaired. Whirlpool sent A&E out on 05/09/12. A repair person from Advanced has been to our home 3 times, and A&E has been to our home twice already. Advanced came to our house on 04/23/12, 05/07/12 and 05/09/12. A&E came to our house on 05/09/12, and again today, 05/11/12.Finally the repair person from A&E said he needed to order parts which are supposed to be shipped to our house. At this point in time we have very little faith that Whirlpool or A&E will do the right thing and repair our machine. We do not understand how a company like Whirlpool keeps getting away with horrible customer service. Whirlpool is the only company we have found where you cannot get in touch with someone who can resolve your problem. Whirlpool told me today that since a repair person is already trying to resolve our problem, we have no choice but to wait until they repair it.

Water began accumulating on the floor, dripping out of the freezer 16 months from installation. Upon investigating I found the bottom of the freezer had a solid sheet of ice on it. Water was dripping out from the back of the freezer and collecting until it froze. I followed a YouTube video that explained the problem, the freezer drain clogs. The video continued with a how-to dismantle the freezer to defrost the drain and drain the water. Apparently the drain is too small and the fix is a new grommet which costs approximately $27.00. I followed the YouTube video and TEMPORARILY fixed the trouble myself. This is a Whirlpool defect, aka, poor design. What is Whirlpool offering to customers to permanently solve this problem at no cost?

I purchased a new Whirlpool Cabrio washing machine from DeWaard & Bode at Bellingham, WA in January of 2007. The serial number is **** and the model number is ****. Several months ago, the dreaded F1 code appeared. The code initiates when the washing machine is started and must be cancelled and started 3 times to continue washing. Later, with approximately 19 minutes left in the cycle, the code reappears and requires canceling and restarting another 3 times, at times 4. I have no extended warranty so I have no coverage for repairs. I also dont want to pay for a service call for what is most likely the computer module as evidenced from the majority of complaints online. This washing machine still looks new and works other than the inconvenience of having to stand by when starting the cycle to reset the code and then having to run upstairs later to reset the machine when its partially through the cycle. At some point, it will likely quit operating all together. I have purchased several appliances over the years from DeWaard & Bode and will be replacing all kitchen appliances again next year due to a planned remodeling but at this time, I do not intend to get them locally due to this issue. I have reviewed several comments online and feel that Whirlpool has a real problem with this particular machine that they refuse to be responsible of. I was offered an extended service plan for 1 year at $132.01 or 3 years for $336.61 but Id have to wait to be allowed to utilize it due to existing circumstances. Im not sure if a fix is actually available. The local dealer did not offer any assistance.

Very disheartening to know that an established company such as Whirlpool does not stand behind their products or acknowledge known product defects. Based on the quantity of complaints logged on this site alone, Id think a recall would be required. Identical to other consumer posts within, we purchased the Cabrio Platinum washer/dryer set (WTW8000BW0). Exactly 24 months to the purchase date, jet planes began flying through our home with the noise concentrated in the laundry room. The dryer has been fine; however, the washer is a whole other issue. The bearings are shot (as many users have cited) and the noise is deafening... even with the laundry door closed, TV on high, dogs barking and flurry of activity in the kitchen! We made a switch to the Whirlpool brand 2yrs ago due to reputation and longevity. Ooops. Lesson learned and $700 out the window. Back to GEs. If youre reading this and concur with our review, just remember... customers always have a choice! Unfortunately, Whirlpool will figure this out the hard way. Just like other iconic brands... Smith-Corona, Blockbuster, Polaroid, Nokia, Saturn, Pontiac/Oldsmobile, Sony and many others. There is typically a reason a company offers tremendous sales incentives (price cut, rebate, special financing) to unload products. We found out why. Thanks for the memories Whirlpool!