Washing clothes is a nightmare. I am constantly removing clothing from the washing machine that have been torn and left with holes. I am utterly frustrated. Because the machine is more than three years old, there has been no solution to my problem. I have now replaced clothing items in excess of $2,000. I am always here that they will send a repairman and yet there is still the problem. This machine is costing me too much money. The newer machines have fixed the problem. There is no gap between the drum and the doorway or rubber piece. I want that piece to stop this nightmare. This machine has taken a dream of mine and demolished the experience. I hate washing clothes but more so having a machine at home and then going to the laundromat to stop the chaos with doing laundry at home.

I used the Whirlpool website contact form, and described an issue I have with the Cabrio washing machine. When the form is submitted, it states that the company will respond in three business days. Two weeks later, after no response, I submitted a second contact form. It has been five days, and I still have not received a response.

Purchased a Whirlpool top loading washer. The agitation cycle is unreasonably loud. So loud you can hear it everywhere in my home and cannot have a conversation within about 30 feet of it. When I ran it for the first time I thought it was malfunctioning and when I called Whirlpool I thought they would send a technician to fix the problem but they told me that the sound was perfectly normal for high efficiency washers! My other high efficiency washers were very quiet. The fact that they think this type of noise is not only normal but quite acceptable makes me quite certain to never buy any of their products again. Very disappointed to see what once was a quality company to be so lame.

Front-loading does not do good job of rinsing. The Whirlpool Duet will not last longer than 2 years. Whirlpool recommends that owners purchase a new washer every 2 years. Whirlpool suggests owners purchase new clothes each week to avoid washing. Any owner would be required to quit their job in order to wash clothes. The Whirlpool Duet front-loader requires 12 hours per load. This means that only 2 loads can be washed in a 24-hour period. Each load requires 10 rinse cycles to remove suds.

This washer is an extremely poor choice if you wash clothes. It has so little water it does not dissolve HE detergent, Clorox 2, or OXI Clean. After even one wash it does not clean your laundry. If you choose to wash your sheets (even though there is a sheets and deep washer setting) its a joke. I could do better by washing things in the tub. I realize its a low usage water washer but you cannot even add more water unless you put it in with a bucket.

My Whirlpool Cabrio Washer is a bucket of junk. I bought the washer in about 2008. I was smart and bought the warranty for approximately 3 years. Since I bought it, I have had them replace 3 water pumps, the tub, the computer, and it still knocks and shakes. It also leaves small frayed holes in my beach towels. This machine should be recalled. It needed a warranty from day one. Washer cost $1,000 warranty every year $130.00 per year which covered the repairs at about $900.00 for repairs. I hate it. I just hate it. I can’t stand it anymore. I need a new washer, someone has got to listen.

Oh what a tangled mess you weave! Inappropriate water usage and bad agitator. The brain is not flexible. Most of all it locks me into a contract of this is it, do or die, you have no other options but to start again. It puts my clothes in abused mode! I say no more, taxes will bring me to buy your competitor. It is very large and way too heavy to move anywhere. No!!! I will never buy another. To the point with all required letters involved, No I will not recommend this (Cabrio washing machine) to anyone, or give it to a friend!

This is the worst washing machine Ive ever purchased. Bought 12/19. The water level never never goes up high enough, to cover the cloths. I have to add water no matter what setting. I hate that. The sensor isnt working. You arent able to adjust it yourself, its computerized. The water shuts off when you lift the lid so you cant rinse out the soap or fabric softener caps. I hate that. The lid locks when the rinse cycle starts so I have to unlock the lid to add fabric softener. Why lock the lid so soon, wait till its in spinning mode. Really really badly designed!!!! Will never buy anything by Whirlpool ever again!

Purchased a Whirpool Cabrio washer. We bought this on sale at a Lowes and paid half the original price. Get it delivered and set up no issues. After about a week of washing clothes, there is a God awful smell coming from the washer because the water does not drain completely! I have used refresh washer cleaner to try and get it to go away. Most of the time there is no smell, but about once every other week, the smell is so bad it permeates through my home and makes it smell of rotten garbage. I do not recommend this washer. The cycle times jump around from the original time it tells you and the smell is just so bad. The little tray where you put liquid detergent doesnt even have a way to drain the detergent into the laundry properly and after every wash I have to dump the tray out because it stays filled with water where the water comes in and causes the detergent to rise out of the tiny hole on top. You might as well just add the detergent directly onto your clothes. I use an excellent brand of detergent that has top reviews and my clothes still dont come out smelling good from this washer. I have tried other detergents too to make sure it wasnt that one. I wish my hubby and I wouldve never paid for this thing and gone with a different one.

I purchased the Whirlpool Cabrio Washer WT5500XW2 from Lowes on 9/12/2012, which turned out to be the worst purchase of my life. It did ok for over a year. It had always been noisy. Now it sounds like a jet airplane when it is on the spin cycle. This machine is not yet 2 years old. Do not buy a whirlpool washer. They are Junk. Plan on getting rid of this piece of junk and buying a new washer. Dont waste your money on Whirlpool!

I have been unhappy with my Whirlpool Cabrio washer since I purchased it from Lowes. I should have looked online before I bought it and then I would not have made the mistake of buying it. The washer leaves soap deposits on the clothes and sometimes leaves a colored soil. It has ruined numerous clothing by tearing out hems of towels and wash cloths and tore a hole in a favorite sweater. I prefer an agitator in my washer. From what I read, I will soon begin to have other major problems and then I will replace it, but not with a Whirlpool.

My wife and I purchased a Whirlpool Cabrio washer 1 year and 4 months ago. Its just three of us in the house. We never overload the washer. Now the drum bearings in the washer have gone bad. I feel that a washer should last longer than 1 year and 4 months. I signed up for the Whirlpool Repair Plus 1 Service Plan which is supposed to cover repair plus 1 year additional warranty. I was told that it would cost more than $1000 to repair so they would only return service plan cost. Whirlpool used to have a dependable product and dependable service. I dont think I will be buying another Whirlpool.

My complaint is basically the same as all the others. Clothes do not come clean in my brand new Whirlpool washer. Ive had two other Whirlpools, and they were fine. This one, however, is a piece of junk. One of the main problems is that the washer is designed to use only lukewarm water, even on the hot setting, it does not use hot water. Another problem is too little water. Another irritating factor is the constant locking of the lid. Another problem is the constant starting and stopping of the agitator. This cannot be good for the motor. Im at the point of giving away my new washer which Ive had for exactly one week. This is a totally inferior product, and I feel that I have been really ripped off.

I purchased this washer two months ago and have been greatly disappointed with it. I put in a large load on wash cycle, but the rinse cycle is barely any water, and is all soapy water, so then I have to turn it back to wash cycle to get more water and then back to rinse to finish it properly. I was never told about the short water cycle, why not? It is still under warranty, but said I have to deal with Whirlpool, and all they can do is send a repairman out and if it is not a defect, it will cost me $130.00 for the service.

I am very sorry I bought this machine. CU rated it pretty good. Nope. 1 - It rarely dries everything completely. e.g., the collars of t-shirts or turtleneck shirts are damp after the load is finished. I have to run the machine again....Energy efficient? Energy schmefficient. and I havent even TRIED to use the low heat delicate cycle. 2 - The cute modern buttons are hard to push in. 3 - The top of the machine doesnt have a level lid... Its curved. Not very useful for setting anything on while you work at any part of your laundering process.

It was time to put the old Frigidaire Washer out to pasture. I researched for quite some time online to find just the right new one. Its all so confusing as they all claim to be the best. The Whirlpool WTW500DW Top Load is the one I chose to look at along with 2 comparable others. I have had Whirlpool appliances in the past and was always happy with them, so I will be honest, I was leaning towards Whirlpool. I purchased the WTW500DW and matching Dryer after looking at the 2 others first. Price was lower, features were more to my liking and better quality/sturdiness was very apparent to me. This was the lower priced machine out of the 3 but had everything I wanted and a little more. The HUGE wash basket is wonderful. I have literally cut our laundry down from 4-5 loads a week to 2! Our clothes have truly never been cleaner.I am amazed at the great job this machine does with a minimum amount of time and water. It is quiet, efficient and the cycles do what they are supposed to do. The absence of electronic pad buttons is greatly appreciated. Its standard dials are easy to read and set. In my opinion, Whirlpool has done it again. Its a great Washing Machine at a price that is lower than others without as many nice features, it is well built and does the job perfectly.

I have a front load Whirlpool Washer and it has leaked within 6 months of having it. The rubber piece was replaced and it still leaked. Whirlpool wont take responsibility for its product. I have to put towels down around the washer every time I use it because it leaks. I purchased this because it is more economical to use a front load but not when water is leaking from the washer.

I had bought from S C Shah & Co, Mylapore a Whirlpool ac 1 ton split magicool dlx cop in March 2016 and installed in March 29 2016 by Cool Control System, kodambakkam From the installation period we had a cooling issue and informed Shah & Co, Mylapore where we bought the ac. They came and checked and informed Whirlpool customer care. Within two months i.e. in May 2016 of installation Whirlpool again uploaded/charged the gas (the service engineers told us this is due to hot summer). Though again we had a cooling issue, we were under the impression as this is due to summer as explained by the technician. After that rainy season came and we didnt use the ac.As we are in December when we complained Whirlpool they said this is due to the copper wire gas is leaking and it has to be replaced and informed that though under WARRANTY, the customer has to pay for replacement (we have used only the 3 mtr copper wire which came with the ac only. we have not used any our own copper wire). Whether WHIRLPOOL GIVES SUCH A QUALITY COPPER WIRE which has to be replaced within 9 months. Now they are informing that you are calling us after 6 months of gas charging, so we cannot service. If you could have called within 3 months we could have serviced you. BUT WE ARE UNDER WARRANTY. NOT EVEN AN YEAR FROM THE DATE OF PURCHASE.Not responding to calls, disconnecting to the calls even if we call their Delhi number 011-49308500. Though under warranty they are not ready to do service and very rude saying, we cant do anything. So, if we buy WHIRLPOOL ac we have to beg them even for their technicians to visit our place. Or we have to do our own service EVEN UNDER WARRANTY. Their local toll free customer care numbers/service executives always give a recorded message saying they cannot service. SUCH A PATHETIC SERVICE.

I have had no issues with my washing machine. Love the different settings. Washes clothes well. Dryer has minor issues like the drying dial stopped moving so I need to manually turn it off. It’s more of an inconvenience, but for the price it should work.

Whirlpool Cabrio Platinum top loader 2014 model - This washer is an over engineered piece of junk. It takes forever to wash anything and it never gets anything clean. I wish I would of just bought the repair parts for my old machine which I had for twenty-three years.

Large tub capacity. Door opens wide without stopping. White Finish has not faded or chipped. Quiet and rarely makes noise even when overloaded. Machine bought 12 years ago and has never needed a repair visit. It has been moved from 2 different locations by using the special brackets. Easy to use detergent holder and fabric softener.

My 4- to 5-year-old Whirlpool Cabrio 6300 began to display errors recently. F1 was the 1st error code I encountered. After giving the washer a hard shove and rocking, it began to work properly again... for a while. I noticed on some large loads that I was getting an LD Long Drain error. I could hear the pump running but with little water flow. Eventually, it would time out and give the LD error. A service tech was called and determined that the water pump was defective, although the impellers inside appeared okay and had no foreign objects to impede its spinning. After spending $225 for the service call, the LD error resurfaced about an hour after the tech left. Tonight I got the F1 error again, and once again the washer responded to a sharp rap. The replacement control board, which the F1 error code involves, is $220 plus labor. $440+ for a repair to a $600-$700 washer? Im going to dissect the main control board tomorrow and look for loose or corroded connections. I cant understand why the LD code occurs when I can hear the drain pump running... just very little comes out. Other times it empties like Niagara falls... I cant understand why it works sometimes and fails others. The pump is either on or off. It doesnt have multiple speeds as far as I know. Im not sure what to do next... probably try to re-sell the new pump that was installed to recoup some of the money I paid for a non-working Cabrio. This seems to be a very common occurrence.. Have any class action suits been mentioned? If so, please feel free to contact me.

My Whirlpool Cabrio cannot wash sheets, blankets or any of this size. It balls up in the middle and form a bubble and only part of the items is washed and washing powders are trapped. I have purchased more sheets in the past 4 years than I have in the past 45 years of doing laundry, because the washing powders are not washed out. I wash on second rinse also, never fails and it still does not get all of it out. The clothing gets off balance if it was more than 3 small items. I have a leveling tool that I put on it often to make sure it is level. It’s something within the machine. I will never, never, never purchase any more Sears’ product. If anyone has jury-rigged this machine to work, please let me know. Sears has refused to help me, even today.

The main control panel on my Whirlpool Cabrio Washing Machine broke twice in the second year of ownership. I bought this in 2006. The part was replaced in March 2007 and then again in October 2007. Now, it is broken again and Whirlpool says too bad, they will not replace it again and will cost us $275 to fix it. People have posted about this problem all over the internet. How can they not help their customers and recall this washer part?

The machine meets our needs and just the right capacity. It has just the right number of selection for proper washing. Very easy to load clothes and remove from the washer. There were a number of colors to select.

About two months ago the washer starting stopping and the UL light continued to come on during every spin cycle. So I would adjust the clothes and start it again. So I decided that I should call a certified serviceman to come out and access the problem. Today a certified serviceman came out to access the problem. After about twenty minutes I was told the tub needed to be replaced and the cost and labor would be $600 or more. I do realize that the washer is about 8 years old but to completely need a repair like a new tub. I am very upset and have no idea what to do.

Purchased a Whirlpool Cabrio Washer a few years back... Started getting F1 error message and just proceeded thru it like most did initially, but now has become pain in the rear just to do one load of laundry as we get the error 2-3 times when we start each load - then on every load w/ 21 minutes left on the cycle. From the looks of things online this is a chronic problem and should be fixed by manufacturer. I called Whirlpool customer service and first person I talked with said they understand it is an issue but no longer are any recalls or reworks on that machine. I asked to speak w/ supervisor and sat on hold until I got one. Was then informed they do know it was a problem but was not something they could do anything about other than schedule a service company to come take a look. I specifically asked if there was at one time a recall or if they were fixing this issue for a while. She said Yes, they took care of some of their customers but are no longer doing that for this model. So basically because I didnt call in at the right time I need to fix my machine myself. I said it will be the last Whirlpool or Whirlpool associated appliance I ever purchase if this is the kind of customer service I can expect... The supervisor just said she was sorry to hear that and to have a nice day. Hopefully enough people read these reviews as I wish I would have before purchasing my Cabrio and dont buy Whirlpool.

This Cabrio Washer and Dryer are horrible!!! Dont ever buy one, they will not fix the F1 code, and Whirlpool customer service is non existent!! I hate this company, and will never buy a product made by them again! Be aware that Whirlpool makes products for Kenmore, Maytag, and a few others!!! I just want to spread the word about this washer! If you just bought one try and take it back for something else!!! STAY AWAY FROM WHIRLPOOL!!!

I bought a Whirlpool washing machine from Home Depot 4 years ago. It immediately started to grow mold in the seal even though I wiped it clean after usage. I called a certified technician to replace the seal. As he was removing one screw on the lock the Washing machine shorted out essentially destroying the panel and rendering the machine broken. I called Whirlpool and told them that the machine was defective otherwise, why would it do that? My technician has worked on hundreds of machines and this is the first time this has happened. The two managers I talked to refused to help me because I didnt have an extended warranty.It is true that I dont have an extended warranty but also, I had faith that Whirlpool had sold me a good product. There is no other explanation for the washing machine to do that other than it was defective. I asked the managers to send me replacement parts, but they refused to do that. The last machine I had was a Maytag that lasted 20 years and when I gave it away, it was still working. I expected no less from the Whirlpool I purchased at Home Depot.

First off, took five weeks to get the damned thing delivered after buying it at Lowes Home Improvement. Have problems with the drain overflowing when the washer tries to empty. Major plumbing work to rectify that. My complaint with Whirlpool is the washer doesnt work. It will partially fill and then stops. The wash light then lights up and nothing happens. I let it sit for three hours and the clothes never washed. It took an act of God to get the washer to empty. It never did spin the clothes. The washer refuses to work through the cycles. $1500 wasted on this POS! Trying to get an appointment scheduled is equally frustrating on Whirlpools website. Never again will I buy Whirlpool!

The machine has an infinite water level setting, an agitator which I feel cleans clothes better, separate settings for water temperature for both wash and rinse cycles, and the ability to soak prior to washing by just leaving the lid up. You can add bleach and fabric softener to dispensers that will add to the tub at the time needed. My machine has been a really good one.

Bought at Lowes. Washer was horribly out of balance on first use. Called warranty # to get service. Was made appointment by Whirlpool for next day. Too good to be true I thought and I was right. A week later, repair company called to make their own appt, chuckled and said Whirlpool does NOT make appointments for them. They came out to see washer and at the time of appointment, the guy said sometimes they come from the factory not hooked up right inside and after he went back to a lady in the office, Jonnys Appl Repair, Bozeman, MT said they would not fix it because washer was not sitting on a concrete floor. They are idiots. Finally, washer completely broke 7 months later. There was no service that would honor ANY appointment Whirlpool made. Went through 6 repair companies trying to get a close appointment date. Hopefully next week will be the magic repair. GO WITH SEARS. Repair is directly through them and they show up when they say they will. Ive never had a new product not working right when purchased at Sears.

My comments are similar to all the other comments on here regarding the Whirlpool Cabrio washer: I bought a Whirlpool Cabrio 5 years ago and have been sorry every wash day since. I have to wash my clothes twice because the machine doesnt fill the tub with enough water to get the clothes clean. I have tried using the bulky setting for all loads to try to get the water level high enough to at least cover the clothes. This is a terrible design and the worst piece of junk. I will never buy a Whirlpool product again...

Since buying a Whirlpool Cabrio washer about 3 years ago have had several breakdowns. Within 6 months the computer completely failed. Since then it failed again. About every six months it costs me around $125 to get it running. The thing is a piece of junk. If the load is slightly unbalanced it just shuts down during the spin cycle. The old Maytag we had ran for over 25 years with the belt replaced once. No other problems. Will not buy another Whirlpool again.

I am so unhappy with your product. Constantly have to restart machine. Never had a problem with my other washer. Takes forever to do laundry. Hate it.

Whirlpool Cabrio Washing Machine F1 code - We have had this washing machine for over 6 years now, and ever since our 3 year warranty time was up, the washing machine will only stop, and display the F1 code as soon as the wash cycle has completed, with 23 minutes left. To start off, with this problem, it is causing me more water, and electricity that should not have to be wasted if the machine worked properly. I called the place where I got the machine, and was told to give Whirlpool a call. I did this, and was told that there was nothing that could be done, and if I would like to schedule an appointment for a tech to come out and work on it, they could do that. YES, I would have to pay for it. Needless to say, the washer has been doing this for over 6 years, and if there is a way to get it fixed WITHOUT having to pay for the repairs, that would be wonderful.

I purchased my Whirlpool Cabrio Washer (WWT5640xw0) at Lowes in East Orlando in 2009. It has worked without issue (other than a slight odor) from then until today, 5-1-12. It has now refused to agitate or spin any clothing, it emits a slight burning smell from the basket, and the basket, when it does decide to spin, spins about as fast as a merry-go-round, banging into the sides of the washer (causing the metal on the sides to bulge out every time it strikes them). It is self-destructing.I called Whirlpool, and they simply refused to address any questions, once I told them that I did not have an extended service plan and that my unit was older than 12 months. I informed them that I refused to pay for an ESP, because I refuse to pay additional monies in order for the product to perform as advertised. They were rude. I said bad words. The call ended.$600 was gone. And I now have to run out and buy another washer, and I can promise you it will not be a Whirlpool. I am a local law enforcement officer. I would love to speak with an attorney about this if a class action suit is pending. I am beyond pissed. My moms chartreuse-colored Maytag still works after almost 30 years of service to our family. It required a new drive belt at somewhere around year 17. The belt cost $45.The Whirlpool CS rep informed me in a surprisingly snarky fashion that it would probably cost over $360 for the total cost of repair and that the only way to know exactly how much is to schedule a service call. I was also told that I would be on the hook for $100 for the service call even if I declined the repair.

We bought this Whirlpool he washer two months ago, and it is the most aggravatingly frustrating washer weve ever had the displeasure to use. There are times when it washes just fine, but I always have to put the mode on deep water wash because the normal mode uses very little water (like its supposed to) but it doesnt clean the clothes. However, most of the time it doesnt wash at all. All the lights will turn off and youll hear this sound and itll drain the water without having been in the wash cycle. Worthless piece of equipment! I prefer the old washer where I have more control. Whirlpool used to be such a good brand, What Is Happening? The new design for their washing machine nowadays generates a lot of complaints, and with good reason (because they suck).

Bought this machine June 23, 2016. First use, I called Lowes where I purchased it to say there is something wrong as it makes a grinding noise. I was informed that is normal for agitatorless machines. I asked if he could hear the noise, and he said yes, thats it. So I disconnected thinking, Wow, who makes a machine in todays technology that is so loud you think something or someone is in serious pain?! Now am at the point where I want this design in pain out of my house! Going to Lowes today to try and talk rationally for a complete refund so I can purchase an LG or Samsung which is what I should have done originally.

Whirlpool front load washer was not working. I waited two and a half weeks for parts. The parts came but they cant fix it. I waited for answer for two more weeks. They decided to replace. After waiting two more weeks, no washer. Its going on eighth week, still no washer. Theres no reason we have to wait so long after paying for the extended warranty in this day and age, and paying good money for the washer.

Bought a Whirlpool Cabrio HE washer over a year ago. Recently, the spin and drain cycle stopped working. Went to find a repair person only to learn that many dont work on this model because of all of its problems. Did find a company who replaced a part ($100). Now sounds like a thrashing machine when it spins. However, now the machine wont even go through a regular cycle. Dont buy this brand!

My washing machine would not spin dry. I had a new pressure switch replaced to a tune of $180.00 which was only 26 months old. I have always bought Whirlpool but this will be my last whirlpool appliance.

When I purchased my Cabrio washer 31/2 years ago I didnt bother to check reviews since Whirlpool was suppose to be the best of the best. An expensive lesson! A washer that spits out codes?!?! Whos got time for this? We paid 899.00 plus taxes for it, now we paid a repairman 99.00 to tell us its not worth fixing. He said the bearings were completely shot. As he was leaving he said his next service call was for the same type of washer! Whatever happened to appliances that last! Going green is all the rage but yet everything from cars to appliances is built to last only a short while. Judging by these reviews I cant believe Whirlpool didnt recall their garbage!

Whirlpool Cabrio washer - Its very expensive and it quit after 3 years. Repairman said computer component went out and it would cost $450-$520 to repair and it wasnt worth it. He also told me I should have read reviews first. Whirlpool said I should have bought extended warranty. No more Whirlpool appliances will be bought for our homes or business.

The washing machine (WFS10055CD) was working fine until two months after the warranty period...It worked the night before, but in the morning, there were no lights. I emailed Whirlpool, but I received no reply. So, I called their number to ask if they would honor their faulty product JUST out of warranty...They wouldnt accept this...I live in an area with no service agents for them so I would also require freight costs of 1,000 km away...I have had an electrician examine the unit to find it may be the control panel/mother board...seems funny many issues with Whirlpool machines JUST out of warranty!!!

The washer in this set is my biggest complaint. I have followed all instructions and tried different methods time and time again and the clothes never come out fully clean. I too experience all the other complaints on this site as well, stuff still left on clothes, dry spots, stains not removed after being pretreated etc. I did some research before buying this set and saw some good reviews, dont know who wrote them but obviously they were highly inaccurate. This is my biggest purchase regret ever, as this set cost about $2500, so disappointed.

Whirlpool Cabrio Model Wtw8000BW - Purchased machine Jan. 2014. It does not wash my clothes clean. Clothes come out with dirty streaks all over them. The clothes I dry on a line smell dirty, like they werent rinsed properly. I have been cleaning the machine the first of every month per the instructions. I will never buy another HE washer again, this is my second one. Purchased a new one with an agitator.

Cabrio washer - What a piece of junk! My washer is 2 years old, it now does its own thing - stopping when it wants, doesnt finish cycle, beeps finished and the clothes are so wet and the washer is not emptied. Then, I put it on drain and spin. One time, it kept going for almost an hour of off and on. My clothes were so out of shape and that was on low spin. I finally took them out and put them outside. The clothes from day one have always come out so wrinkled and that too is on low spin. Im afraid to use high spin. I know you have to for towels, but it still does not drain. It shuts off and on when it feels like it. My first contact with Whirlpool was, Well, did you buy the extended warranty? I hate it when asked that when purchasing any product. Its like saying, This is a piece of crap. Im warning you now so buy the extended. So right there, I felt Whirlpool isnt willing to help. What else can we all do here? Please advise.

I purchased my Whirlpool Cabrio H2Low from Sears 6 years ago. After numerous problems with clothes not getting clean (soap spots, stain transfers, etc) I learned the only setting I could use that actually cleaned was bulky with an extra rinse (so much for the energy efficiency). My first major repair was in the first year. Weve since had 3 more and the darn thing died again this morning. First the motherboard died and needed replacement, the drain pump failed, the door lock failed, and twice now it stopped spinning. At first I thought maybe I was just unlucky and bought a defective machine but repair sites are filled with reports of similar problems with these machines. I will never buy another Whirlpool product again.

Whirpool Cabrio Washer - Do not buy this washer. Clothes are not clean. They are twisted with residue still trapped in the wadded up mess. Even if you select deep water clean, your clothes will still have the same dirty marks on them as when they went in. Also, there is no spin cycle. If youve got a bunch of wet towels you just want to spin the water out, you can forget it. You will have to do a complete wash. And the 1 star is not even appropriate but there is no choice of a big fat zero. Wasted a lot of money on this when Ive had great luck with Kenmore.

I am a very unhappy owner of a Whirlpool Cabrio Model: wtw5640xw0 & matching Dryer. About 4 years ago, my husband chose to replace our 11 year-old Maytag Performa Washer & Dryer instead of fixing a part that needed to be replaced in the Washer. I was upset with the very first load of laundry in the Cabrio and I was extra upset that my husband had junked my perfectly awesome working Performa Dryer. )-: First of all, the Cabrio set is Extremely LOUD! Secondly, I often have to wash loads more than once because they do not get clean the first time. Next, the Washer is Always knocked off balance. Ive resorted to using the settings on the Washer with the low spin every time, no matter how light the load. And, now there is something wrong with the lid lock mechanism (which has always sucked anyway), but this is a new problem... I was just checking on the internet to try to figure it out when I stopped to write this review. The lid will not lock & the lid lock light wont go off, so the Washer wont do anything at all! I can not express enough what a piece of junk this Washer is & Im never going to allow my husband (who doesnt even do the laundry) to choose my Washer & Dryer again!

Bought a Whirlpool Cabrio. Noticed it was getting really loud less than a year into owning it. Called while it was under warranty. The tech said it was fine. Within the next year and a half it got so loud, you cant hear anything else in the house while it is running. Now it is leaking from the tub seals and the bearings are going out according to two service techs I have had come look at it. They say it is more expensive to fix than the washer is even worth. This is due to the parts that would be used to fix it are the same cheap Whirlpool parts that were put in it in the first place. They both said that these are not good washers and commonly go out about a year and half to three years old. Shame on Whirlpool for making such a low quality product and not being willing to do anything about it.

I purchased a Whirlpool Cabrio in 2009. It worked so-so over the years but recently stopped completing cycles, citing false load balance errors and leaving towels and sheets sopping wet at the end of a cycle. Three repair appointments later, and still no success. I am thoroughly disgusted that such an expensive machine only lasts four years. Based on the service techs attitude toward the machine and other consumer comments, Im guessing I will have to replace it. You can guess it will not be with a Whirlpool machine!

I had this washer (WTW7990XGO) 5 years and finally had to replace it. It started with the touchscreen. No matter how often it was calibrated it was very frustrating to get it to respond. It would start dinging and going thru all the cycles at random times. Then there was the error code for the door lock. The door lock wasnt the problem, the surround was slightly warped and the door wasnt catching. Warped Im sure from having to literally climb into the machine to retrieve the clothes! Then a few months later it was another error code - the machine wasnt draining fast enough. It didnt drain at all. We had to use a water hose to drain it. After the second time with that, I went and bought a new washer - different brand, dials - no touch screen, and it has an agitator. Unfortunately, I ran into other customers in the appliance department who were having the same issues from 2 other brands of electronic washers. We all went back to as old school as was available.

Have had this washer for one year. Clothes have never been clean since day one. Dark clothes come out with white marks all over. Having to use an extra rinse cycle or set on bulky items - whats the point of a high efficiency appliance? Still not clean after that anyways. Stains such as chocolate and toothpaste still remain after washing and my husband complains of finding small holes in his clothes. Lid needs to be left open at all times or you get a funky smell. I am using the HE liquid detergent, even tried a cold water product for cold washes. I hate this washer. Wish I had my 20 year old Kenmore still.

Whirlpool Duet $1300, in the past we had great service from other Whirlpool products. Just a more modern look and knowing it was a company we had used in the past with very little or no problems so we expected the same only with energy and water savings. We are energy aware and believe in conserving energy and water where we can. My wife wanted to stick with the brand that gave us good service in the past and chose one of their most conservative units on the market (I believe it was based mainly on looks). What burns me the most about this unit is its constant consumption of clothing, the repair guy found nothing askew with the unit and suggested smaller loads. So we reduced the load size smaller and smaller till we were washing each outfit separately and guess what, it still ate clothes, just chews them up.We lose about a hundred dollars a month in clothing. This washer tears holes and shreds clothing on almost every load, I have to put shirts and lighter clothes to the back of the washer then load the heavier blue jeans and such toward the front and hope they finish in the same position or something is ruined. The fabric becomes distressed, stretched, shredded or has holes, or any combination of the above. We have taken to going to a laundromat or sending clothes to the cleaners. These units are three years old and we are now looking for a replacement for the washer because the local service guy won’t even come out any more. This problem surfaced within a week of the first use of the machine and has remained steady, as we are retired and travel a lot we are not always using them so they are what I would term very lightly used.

I purchased a Whirlpool Cabrio washer in 2007 and had to replace the control panel for $300 each time twice.

We purchased our a model WTW7800XWO 7 years ago. Our lid kept falling down when loading and unloading. Very annoying. 3 years ago it failed to lock down which means the washer will not start. We learned to press down on the lid sides to get it to lock. Then it became loose where it connects to washer and we duct taped it to make it work. We put up for that for a year before having a repairman attach a new lid. 1 year later it did the same thing... And we put up with it hoping it wouldnt totally fail. Today it failed. Since the 1st repair cost 250.00 we decided that we will get a new washer rather than spend another 250.00. We will go with American made Speed Queen. We have had Whirlpool appliances since we were married 50 years ago.

We purchased a 4.8 Cu FT High Efficiency Front Load Washer in February of 2016. What a nightmare. Just a few months after having it, we kept getting an E3 error message that would not go away. After 2 weeks of waiting before a tech could come out there replaced a door mechanism said it would be fine. After the next wash same thing, same problem. Could not even open the door to get my laundry out. Again they could not get a tech out for at least 2 weeks so Im stuck with the cost of getting my laundry done elsewhere. This time it was the motherboard. Had to wait a week for that to be shipped out. This was all completed in June 2016. We are now the beginning of September and same problem. Again we are told at least 1-2 weeks to get a tech out. Seriously Whirlpool, we are your customer. I have a family and we need to wash our clothes. We spent $1200 on this machine only to have to take our laundry to a public laundry mat because your machine keeps breaking down. They will not replace the machine even though this is the 3rd time with the same problem. The customer service is horrible. They are not willing to help in any way to get this fixed much sooner for her or give us a new machine. This one is obviously a lemon! I will never purchase any Whirlpool appliance again and I suggest based on some of the reviews on here no one does. Next appliance I buy I will do more research for sure.

I purchase newly Whirlpool washing machine but it was not working from the first day of my purchase. So many service Engineer came but nobody can solve the problem, so I suggest to all please don’t buy washing machine from Whirlpool. I am very disappointed from this company.

I am writing this complaint because of the very poor service of Whirlpool. My washing machine broke after 1 year of use. Luckily, I was on my 2-year insurance. The wiring fully collapsed and I needed to change the whole drum. I called Whirlpools customer service and they said that they would fix the problem after 2 weeks. They came on the day and found out the problem and ordered a new drum. They said they would fix it up on the 5th of December, and it has already been over 3 weeks. On the 4th of December, Whirlpool called me and said that the item they had ordered for me has been damaged. I am not satisfied by these products because it is only a drum (it cant break that easily). I cannot recommend this company to my friends and family due to the quality of the products and the poor customer service as I was waiting on the phone for almost an hour trying to get through.

Cabrio Top Load Washer model WTW6800WW1 - Although we were very happy with the vendor where this was purchased and happy with the majority of the washer function; there is a problem with the cabinet & lid connectors rusting. Specifically, the lid connector on the left side totally rusted out, and also around the bleach cup, rust. There are also rust spots where the seam of the top section of the washer meets the bottom part. The washer was purchased in 2009. We have had it serviced in the past, prob 5 years ago, it needed a new motor and the rust was beginning to show then, while under warranty. I recently called Whirlpool and the associate told me that she had never received a call with regard to this type of problem. She did give me names and phone numbers of appliance repair in my area. I find it odd that Whirlpool would not make their associates aware of issues like this. I searched online and saw more than a few complaints about rust. So on it goes, no recourse, and as I read about the problem from others reporting this; it was mentioned that the vapors from the bleach cup etc, contribute to the rust. Additionally, even if it was under warranty, I was told that this is considered cosmetic and it would not be covered. Until... and I can only suppose, that until the lid possibly falls off while lifting, the cosmetic ruling may then turn into a function problem. Now there is also a squeaking sound, so off to call the appliance repair, check the cost and next time... buyer beware. I guess a lesson in science as well, hopefully this design flaw will be corrected for the next models in process.

I had my Whirlpool front load washer stop working all together. Well the pump went out it filled up with water and shorted out the circuit board/control panel. Was going to cost more to repair it than to just go get a new one. I will never get a whirlpool ever again.

I purchased a Whirlpool Cabrio set 3 years ago based on their brand reputation and consumer reports. It has been a terrible experience since the moment the warranty expired. First, about 1 month after warranty expired, I had to replace the main electrical board. Then about 3 weeks ago, the drain pump failed. I purchased the $110 pump and installed it myself. Now this week, the spin cycle sounded like a jet engine. I took it apart to find that the bearings were shot on the drive shaft. I figured, well it is just a wear item, understandable right? So I went to order parts and got told that I have to order the whole outer tub for $250 with shipping! For some bearings! I called Whirlpool directly and was given no explanation other than Call some parts distributors. They may be able to help you get the bearing separate, but we dont do that and there is nothing that we can do. Amazing. I equate that to having a faulty brake on my car and being told that I have to replace the whole axle!Fortunately, the washer never really did a great job. It was loud and tore clothes up, so the decision to part ways was not too difficult. I have the list of brands they make and will be sure to never buy another. Im selling this one for parts. Im sure there are others out there that will need a pump and control board soon!

Weve had this washer for about 9 months now. We noticed that the loads being washed small or large werent coming out clean. When wash cycle finished items were covered in soap residue and or had large dry spots where water had never touched the area. When our sheets were washed in bulky/sheet cycle and deep water this happened. Maytag sent out repair person to find the water pump went bad, pump was replaced. After repair same bad washing results as stated previously. Maytag then sent out repair person for the second time. This time the main electrical board was replaced. Still after two repairs wash loads are still coming out dirty, soapy, dry in spots in any of the selected wash cycles large or small. Third call to Maytag and a third scheduled repair date coming up in a few day. Over the phone the Maytag employee only words of wisdom was, Did you buy the extended warranty. So unless there is a third failure I believe that this washer is just a poor design.

I have read most of the reviews and it seems like I have ALL those problems with my Whirlpool Cabrio, but I also need to add that there is rust around the bleach dispenser and I DONT use bleach. The inside is also rusted, but its not visible until you take a good look inside because its under the white paint but its all around the inside. So I had to stop using the machine because I now realize what was the cause of the damage done to some of our clothes. We all need to get our money back and have this washing machine picked up and thrown away!!!

I have had my whirlpool top loader washer 2/12 years. There are 3 adults in our household, but we do at least 1 load per day. During a spin cycle we heard a loud bang and then the washer starting spinning very fast. I called for repair and was told the cost was 500.00. Now I must buy a new washer as that cost is excessive and I see this is a common problem. This new washer will not be a whirlpool!!!

I will never purchase from Whirlpool again. After 3 years of use in a 2 - person (adult) household, my Whirlpool Duet (WFW94HEXW2) washer suddenly stopped working with an F6 E2 error code. I unplugged / plugged in the machine, took off the top & checked connections, and let it sit overnight. I could not get it working. Speaking to a local repair technician via phone, he indicated it is likely the control board. Whirlpool changed that part from part number W10406632 to part number W10427967. Before spending the money on a service call, he suggested I contact Whirlpool to see if it is under recall. I contacted Whirlpools customer service. They told me the washer is not under recall but I may qualify to purchase their Repair + 1 service. When I expressed frustration at spending so much on a product that lasted only 3 years I was told This is not a known quality issue or recall. I will document a complaint for you. The chat session was then terminated by the customer service representative. We will spend over $300 to replace the part that Whirlpool obviously knows is flawed. However, I will not pay for an additional Whirlpool repair service to fix something that should not have broke in the first place. And Whirlpool (including Maytag, KitchenAid, Jenn - Air, etc.) will never get our business again.

WTW5640X The machine is tearing up clothes of many including mine. I gave them the benefit of the doubt and thought I had over-loaded the machine. Not so. There has been nothing run through the machine other than clothes and bedding. When I called for service 1 1/2 months after warranty is out of date I am told I can have a service call including parts and labor and another year warranty for almost $400. If it werent for the numerous reports online of the machine doing the same to others I might have gone for it. Shame on you Whirlpool. Are you the next GM?

I purchased a Whirlpool Cabrio Washer In July 2014 for $937 cd. What a waste of my hard earned money! I have had nothing but issues with it since I purchased it. The retailer no longer sells them as they have seen nothing but complaints with them yet Whirlpool did nothing to help me as a client. It does not wash the clothes, there is such a foul smell even when cleaning it once a month as requested and the clothes comes out soaking and not rinsed properly. The technician came out and advised the washer was not broken. That is just the model. I have requested supervisors to call me back and most recently wrote the corporate office. I am out almost $1000 and in a situation where I have to go purchase a new washer as I just cant stand to use this product any longer. I am shocked they have not placed a recall on this model. What a poor product.

Bought it less than 2 months ago. It doesnt wash. It doesnt spend. It works every 2-3 hours if Im lucky. Its the worst product ever. Its not like it was refurbished. It was brand new. Smh. I thought it would save me money by buying a washer. Off to the laundromat I go. I do not recommend this product especially to someone who has a family and on a budget.

In the first year of my Whirlpool Washing Machine, the motor quit working entirely. Fortunately, the machine was under a 1-year warranty and the motor was replaced by a Whirlpool service technician. My big complaint with this washing machine is this: Even though you select hot water for the wash cycle, the machine has sensors in it that only allow the water to get lukewarm. If it senses the water getting too hot, it adds cold water to bring the wash temperature back down to 78 degrees F. Next time I will do my research and buy a machine that actually allows one to use hot water.

I have called Whirlpool multiple times because our washing machine model #WFW9290FW has been out of service for 5 weeks now. I have been informed that I need part #W10604640, which is on back-order and they wont give me any idea of how long it is going to take to get this part replaced. Apparently, there are 96 total people who also need this part. I find it hard to believe that a company this big would not have this part on hand and they would not have any idea how long it would take to get it replaced. I asked them to give me a new washing machine for free to replace it because of the poor service and the unreliable washing machine. They told me they could give me another washing machine at 40% off, but based on the lack of follow-up and the amount of time that has passed since my initial call, I dont want another Whirlpool product. This is the worst customer service ever.

Duet Washer GHW9150PH0 - The washer is about nine years old. Last year I got the dreaded F-11 error code, and had to purchase a new controller board and install it. Now the spider arm on the basket has snapped (cast part). Ive been on the phone with Whirlpool for over a half hour now, and all I get is We have to send a service tech out, and you have to pay for them. I have the broken part in hand, I know the Whirlpool part number, yet they want me to pay for a tech to come see the part and confirm it. Ive been unable to talk to a manager yet, none are available.Eventually the lady agreed to replace the broken basket, after telling me at least five times she could not, but she refused to replace the tub which was destroyed when the basket broke. Ill be calling back to talk to another agent soon.

Whirlpool front loader duet washer WF9400SW01 - I bought this washer brand new in 2007. The rubber ring by the door started to grow mold after 2 years, the washer collects water after wash. Water was dripping down to the drum and sit there. If I forget to check and drain it by turning on in the rinse cycle, it wets the entire floor. And it sounds like a freight train after 4 yrs when it spins. My last washer lasted 20 years and it was a whirlpool top loader. Thought I might get that with this one.. but NOT.

I purchased a compact frontload washer. At first, I was getting a code f30, which took the technician weeks of coming to my home and changing different parts to finally accomplish that problem. After that, the machine would not go into high spin to wring the clothes out. So everything comes out soaking wet. After two different companies (Herbs Appliance and DanMarc Appliance which I got from my service contract) changed speed control, board, latch control, main computer, and top control board, the machine finally worked for a little while. Not long after, the machine is no longer wringing out once again. I am no longer under contract but had a repairman out three times to inform me this machine is a lemon. Whirlpool tells me I am no longer under contract, but my argument is this is not a new problem but a preexisting one.

I purchased a front loading Whirlpool washing machine March 2017. I have need to have the drain pump replaced and the motherboard replaced. Each repair took 30 to 45 days to get parts and service. I would not recommend the washing machine.

Has multiple wash Cycles. Big enough to wash a comforter. Has a delay setting so I can set it 8 hours in advance. Easy to load, easy to add the wash ingredients. Its a top load so its easy to get everything in and out.

Whirlpool cabrio mod. WTW7300XW1 - I purchased this washer Nov. 2013. It did not work right from the day of delivery. Our clothes come out dirtier than before washing. Machine smells awful. I spend more in machine cleaner than in laundry soap. I have always purchased Whirlpool. Very dissatisfied with this model.

So far this washing machine has been perfect. Its a top load not front load which I prefer. Im not a big fan of how it locks and I cant throw other stuff in once it started. Other than that Im very satisfied.

Bought the Cabrio washer in March 2011. Have had the same problems as everyone else. The machine is constantly off-kilter, does not wash well due to lack of water. Sounds like a freight train when spinning. Bulky clothes dont drain properly and have to be rinsed and drained a second time. After one year of ownership, the entire control panel had to be replaced. The next year, the same control panel had to be replaced again plus a water valve had to be replaced. Thank God I bought the extended warranty. The repairs would have cost me $1000, more than I paid for the washer in 2011. Total piece of junk. AVOID AT ALL COST!!!!

Agreeing with many. How disturbing to buy a Cabrio Whirlpool washing machine about 5 years ago. I might as well go down to the river and wash my clothes. The bearings went out which means I have to be the spin cycle. I am hanging out my clothes on the line - very wet - until my husband buys the part and fixes it himself. I had my maytag for 25 years. An awesome, dependable machine that we laid to rest because of rust. We should have gotten another drum instead of buying this machine. Where are the engineers that are making dependable appliances to last a LONG time? We have not gotten smarter. Or we only care about the all mighty dollar. Make something to last a short time so that you have to buy again. We will do some extensive research the next time we buy a washing machine. Do not buy this machine!

Whirlpool washing machine #WTW58ESVW1 - I bought this thinking Whirlpool was a good brand name. I was totally wrong. My machine is two years old and the auto sensor switch has quit working 6 times. One time it only did 6 loads of laundry. Another it only worked for 6 weeks. That time I replaced the switch myself to save money on a repairman. Ironically the switch is still under warranty but they will not replace it unless a serviceman comes to confirm that the switch is dead again. This is because 2 have already been returned to them. Obviously, there is a problem with the switch. The company will do nothing. They used the excuse that I did not purchase an extended warranty. This is merely an excuse. Do not purchase any Whirlpool products. You will be wasting your money and time having to end up going to go out to do laundry.

The washer (Cabrio WTW7800XWO) was less than 2 years old and we had a motor go out, so we paid a repairman to come out and repair the machine. The total cost was over $300. Now 2 months later, we get another code on the machine and Whirlpool says, We are sorry but there is nothing we can do, but if you would like to pay $219, we can get a repairman out there to check out the machine and repair it. Theyre also giving the machine an additional year warranty. Shortly after that, I noticed the lid was not staying up when I opened to put clothes in it to wash. So since I was wondering what was happening, I looked at the lid and to my surprise, the springs that hold the door up when open are built into the plastic lid cover that has a see-through glass on it. Right where the springs are located, it must be a stress point and the plastic lid has since cracked and is almost about to break off. I am now in the process of ordering another lid and Whirlpool offered to sell me a lid for $226 but I think I shall buy it from someone else as I dont want to put any more money into Whirlpools pockets. We paid over $1000 when we bought this machine. Now it is about 2.5 years old. I hope there is a class action lawsuit on Whirlpool as I will definitely join in if there is. This company needs to go out of business if they continue to sell machines like this that have so many problems especially when they are less than 2.5 years old. Goodbye Whirlpool. You have lost many more customers as I shall be letting everyone I know about all the problems and complaints about this machine.

We purchased a Whirlpool Duet Sport Front-Loading washing machine December 5, 2006. Approximately six months later, the machine would not come on! Service determined the motherboard was faulty. Since it was under warranty, they replaced it. We continued to have the same issue with turning the machine on. The technician instructed us to hold the start button down for a minute or unplug the machine to reset it. The problem persisted. Now, we are told it needs yet another motherboard. Cost - $500! We paid about $650 for the machine! (The manufacturer only offers a one year warranty on the motherboard) What incentive do I have to purchase this part? After all, Whirlpool only warranties it for a year! That in itself, tells me they cant guarantee the quality of their product.

Whirlpool washer Model WGD4815EW1. Bought this washer just about 4 months ago and right away I hated it but was told by people that all the machines had gone to the lid lock and that the government had mandated the energy saving devices on the machines so the machine will only put just a little water in the machine. I have been VERY VERY unhappy with this machine. My husband figured out a way to bypass the lid lock mechanism. Then after washing clothes many times I found out in order to get my clothes clean I had to just set the dial to Bulky every time OR I had to wash the clothes 2 times to get clean if I didnt. Once we bypassed the lid lock and then I figured out where to put the knob so the clothes would come clean I was fine until last week the machine just would NOT wash or do anything... it filled with water and just sat there until my husband got the water out. I located a Speed Queen from an appliance store and I am much happier. It does not have the CRAZY lid lock on it. I realize that some children are apt to mess with the washers. But I dont have children anymore and when I did I had a laundry room with a lock up high on the door so they could not play in the laundry room. I dont understand why this so called mandate could not have been done in a way as to allow those with kids to have the option on the machine with a built in code device to set the machine so the lid will lock and those of us without children in the house to opt out of the code to set the lid lock. NO REASON why we cant have a CHOICE. As far as I see it is a way for the government to try control more where they need to keep out. The cars have been designed with safety locks for children to keep them safe, but it is up to you to choose to use them. Same principle! Now for the mechanism to make it so the machine will only put so much water in the machine to wash. Youre NOT SAVING any ENERGY or WATER if you have to wash the loads twice!! This whole mandated business with the newer washer machines is a huge JOKE on everyone. I will be searching out used machines and having them rebuilt because I dont EVER plan on buying another one of these newer machines. If enough people stop buying them the manufacturing companies can raise some cane with the government to get the mandate lifted. NO I will not buy another Whirlpool washer. I encourage some of you out there who LOVE a challenge to figure a way to change the stupid motherboards on the newer machines and create a great business for yourself because if someone else can create it you can recreate it.

I purchased this Whirlpool washing machine model# WTW4950XW2 and after 10 months of use, it broke down. The repairman fixed it (gear box) and said that the motors and the control boards went bad. I didnt get a weeks use out of it because the motor went bad. He came and fixed the motor and it didnt work once after that. I called Whirlpool up and they sent their serviceman out twice and they didnt do much but reprogram it and both times it didnt do one full cycle. Now they (Whirlpool) are going to put a new control board in and hope it works. Whirlpool wants me to get another years warranty on the machine & charge me $100 and not do anything about all the money I spent going to the laundromat (2 months worth) while this machine was not working. There should be a recall on this machine for replacement & reimbursement of all the time and money lost.

I have been blessed with my washing machine. I have never had one problem with it. I have had my machine for over three years now. It is a reliable machine, with five different water levels from small to super. It also has three different water temperatures (just great). I am very pleased with my washing machine. I cannot tell you how many machines we looked at before selecting our Whirlpool, thank goodness we did.

Error f1e2 error. Washer less than 2 years old.

I always seem to get Whirlpool washers. They are dependable but when they break down theyre down and usually its better to replace than to fix it....I would rather have a Samsung product because theyre more modern and have better styles to them.

In March 04 2014, I purchased a Whirlpool washing machine. After having had a Whirlpool for 17 years without any problems with it, I purchased another one. This last one is a piece of junk. I dont even want to talk about the noise, I think it is expiring or on its last leg. They should fire the engineers that invented this model and bring back the other engineers that invented the one I had for such a long time, they far surpassed these space scientists that they now have. On August 8, I called Whirlpool, they sent me someone from Dinos appliances. This man tells me that there is nothing wrong with this machine and that he re-calibrated it. Whatever that means, it is still not wringing the clothes properly. There are only 2 people in my household, so my loads are not very large. I even tried this Drain & Spin cycle after the wash was completed and the clothes still came out too wet. I also have a Whirlpool Dryer and I will not replace it with the same brand. I also will never buy a Whirlpool product again and will make sure that I will share my experience with everyone I know.

I purchased a very expensive Cabrio top-loading washer thinking I would never have to worry because supposedly it’s the top of the line, right? Well, I have it a few years; the first week they replaced the basket because it was ruining my clothes. And then I had to replace the pump because of a coin getting caught and putting a hole in the pump. Really? What the heck? Now the basket is all shredded at the top. Obviously that isn’t right, so what do I do now? Replace the basket again? Who gives them the right to charge so much for a piece of junk? Plus, it’s supposed to save on water, but I feel that the clothes don’t really clean well. They hardly feel wet coming out of the machine.

This Whirlpool Washer Mod # 4800XQ2 eats holes in all of my clothes, came from Lowes. I still have the sorry machine.

This washer was expensive, platinum line. Clothes never smelled fresh and clean like they should. There is not enough water to cover and clean. After 4 years it started smelling dank and unpleasant even after cleaning cycle is run. Now I discover it has been leaking for quite a while. It will be 6 years old in July. The top wont stay up. This happened months ago. The part alone is 250.00 according to several sites. I just prop it up. Very displeased with this poorly constructed, expensive rip off!

Im so tired of the mold smell that never goes away, even after following their cleaning cycle many times over. I dont know what to do but I spent extra $ to purchase my washer and now this!

I was a salesperson for GE for years and thought that they made the best washer for several reasons, but eventually had to purchase another washer which was a Whirlpool. Have been very pleased with my choice and would purchase a Whirlpool again. Washer is 14 years old.

I just love the durability of my machine and the features that it offers. It does a great job washing my clothes and I feel like its a solid appliance that lasts for many years and its good quality for the price.

I have owned a Whirlpool Cabrio HE WTW6400SW3 for two years and have had nothing but issues from the start. Control panel was replaced twice under warranty. Also the clothes (socks underwear) were under the tub blocking the drain. This is not covered under the warranty. I was told by the repairman that this is the usual issue. He told me they took the front loader design and just stood it up with no protection from garments and coins getting under the tub, through the under tub filter often and into the drain pump. You are kidding me? Almost $1000 for this washer and its so ill designed. I have read forums that this has been an ongoing issue for several years yet Whirlpool continues to build these. I dont vent to forums often but just now I finished removing the tub to remove 2 socks and 7 cents. Also, I had to remove the drain pump and found another 16 cents inside it. So far the pump has not been ruined but this time water is coming out from the machine so will probably be ordering another pump for it as well. The wife wants it out of the house tomorrow and not another cent spent on it. But it is only two years old. What do you do? If you are reading this because you are searching for a new washer do not purchase a Whirlpool! I have gotten nothing but grief and was put off by their customer service dept as well. I guess after fielding so many calls about the same thing they have been told to just put all the calls off as no big deal. I am sure Whirlpool is making a killing off the sales on this unit. The claims made during the sale convinced me. What a joke. Look around the internet and you will find hundreds if not thousands of the same issues.

I purchased a new Whirlpool washer, from day one it did not work, for the past month I have been trying to fix the problem with service people. The service people were at my house 5 times without any positive results. I was told by Whirlpool representative that they will not replace the washer or give me my money back, they have 12 months to fix the problem. I have never seen such a bad customer service and arrogance towards a customer. I will never buy anything manufactured by this company.

This washer never worked right. It simply mixes the clothes up with little water. A real piece of crap. See the 2000 other complaints. Time for class action suit.