Purchased Whirlpool Washer Mod# WTW57ESV1 12/9/2011. Washers transmission blew on 1/20/2012. Requested Whirlpool replacement. No results. Will never purchase Whirlpool products again.

In October 2009, we purchased a Whirlpool Cabrio topload washing machine for almost $900, because my wifes sister had a 1-year-old one and had been pleased. The Cabrio replaced a 3 1/2-year-old Maytag that died with a seized-up transmission. Maytag is also a Whirlpool product for those of you who do not know. We had issues at first with it going off balance but dealt with it. It was also taking 40+ minutes to do even a small load of laundry, but again, we dealt with it. Fast forward about 3 years, and we notice the machine is making really loud sounds during the spin cycle. I checked for any obvious issues but found none. The noise kept getting louder with each use. Finally, I called a repairman to check it out. His diagnosis was quick. The bearings were going bad in the machine, and he said it would eventually fail. He quoted me a price of between $400-$500 to repair because the job is very labor-intensive. I declined the repair but still had to pay him a trip charge. Then I checked with my wifes sister about hers, and she said hers had been making a very loud sound for several months but they were just ignoring it. I told her about the diagnosis of mine and advised her to tilt the machine back to look under it. Sure enough, there were oil stains under her machine, just like mine, indicating the bearings were failing. So we have 2 Cabrio machines, one 3 years old and the other 4 years old with the exact same problem. I called Whirlpool since I had registered the machine when I purchased it. They basically told me to go fly a kite since I had not purchased the extended warranty. They said I could attempt to repair it myself to save money, but they advised to have their repairman do the work. Well, no kidding. What a joke. They expect you to buy a $900 machine and have to replace it every 3 years. I am done with Whirlpool products. FYI, Kenmore products are also made by Whirlpool, so Sears is not an option. My wifes sister and we bought new GE washing machines, and both of us purchased the extended warranty this time. For $129 (5 years), its cheap, peace of mind. Whirlpool is crap. I would suggest never buying any of their products. I know we never will. Once they have your money, they dont care.

Had washer since 2016. Have NEVER washed a load where there was not a problem from washer dancing to having clothes come out without water ever touching them. Would NEVER recommend Whirlpool! Tried to contact Whirlpool website to register a rating & even their website is defective - could not get through after several attempts.

I wish I had read all these reviews before buying this junk/lemon of a machine. Havent had the machine for a year yet and lots of problems. Only can wash five towels at a time and thats pushing it. Decided I would deal with it, until it gave other problems. First sometimes skipped cycles, then water came in when it was spinning. Called for service. Checking to see if we even can get you service in your area, representative says.About a week later tech comes and puts two parts in and left. Happy to get laundry going but, guess what??? Washes only doesnt do anything else and trying desperately to drain water out. Of course I have to take clothes out and bring to laundry. Tech comes back next day. Now he cant get any cycles to work either. Fried, tech says. Sets me up for next Saturday, fine.Now get a call on Monday, not coming. Tuesday is next appointment. Apparently inventory representative says. Didnt know that before??? Call Whirlpool, service first, then company. I want a new one, this is definitely a lemon. Nope, tech will be there on Tuesday. I hope Whirlpool reads this. They should be ashamed of their company. They used to be good, always bought their products. Dont buy these machines, trust me you dont need the aggravation. Totally disgusted.

I had this washer (WTW7990XGO) 5 years and finally had to replace it. It started with the touchscreen. No matter how often it was calibrated it was very frustrating to get it to respond. It would start dinging and going thru all the cycles at random times. Then there was the error code for the door lock. The door lock wasnt the problem, the surround was slightly warped and the door wasnt catching. Warped Im sure from having to literally climb into the machine to retrieve the clothes! Then a few months later it was another error code - the machine wasnt draining fast enough. It didnt drain at all. We had to use a water hose to drain it. After the second time with that, I went and bought a new washer - different brand, dials - no touch screen, and it has an agitator. Unfortunately, I ran into other customers in the appliance department who were having the same issues from 2 other brands of electronic washers. We all went back to as old school as was available.

I bought a Cabrio three years ago. Unless you wash everything on gentle and turn items with zipper inside out, it puts holes in everything. Then exactly one week after the warranty was up, it started giving an error code. I called the company and was told this was a common error and they would send someone to look at it for $150+. It would likely be another $300-$400 for parts and labor! I had someone else (not Whirlpool) come look at it and they said it was a bad computer that I should just replace the washer, because it would cost more than it was worth. So for two years, we have had to wait exactly 11 minutes for the washer to fault then restart it and repeat 3-6 times. It takes 2.5 hours to complete one cycle. If this is such a common error, why havent they fixed it or recalled the piece of junk?! Because they can make a lot more money this way! Three people I know have Cabrios and all have the same issue and all happened within a month of the warranty expiring. I am starting to think there is some sort of timer that makes it go bad just after the warranty expires on purpose. I will never buy another Whirlpool, Maytag, KitchenAid, Jenn-Air, or Amana (all the same company with different names).

My whirlpool Cabrio washer top load had the rust problems, bearing problems, support arms replaced along with the complete drive assembly motor bearings and all the parts. My bearings have failed 3 times since 2009. This machine is junk. Customer service at Whirlpool is a joke. They treat you as if you have had to do something wrong. Finally I spoke with a salesman who said speak with the warranty company. I have the extended warranty which I advise everyone who purchases an appliance to get one. So I spoke with them and they sent me a check for a new machine. I must say our warranty company has been very helpful. So THIS IS MY WARNING TO ALL. PLEASE DO NOT BUY FROM WHIRLPOOL. IF YOU DO YOU DESERVE WHAT YOU GET, SORRY TO SAY... Have a great day.

Whirlpool Cabrio Model Wtw8000BW - Purchased machine Jan. 2014. It does not wash my clothes clean. Clothes come out with dirty streaks all over them. The clothes I dry on a line smell dirty, like they werent rinsed properly. I have been cleaning the machine the first of every month per the instructions. I will never buy another HE washer again, this is my second one. Purchased a new one with an agitator.

This piece of junk just broke down not even one year after the purchase. Every singe Whirlpool washing machine has broken one way or another. This one will set the wash time for 57 minutes, and exactly 24 minutes left in the cycler, you hear this big crash and then everything stops. Another dumb thing about this piece of crap is that when the problem happens, the POS keeps the lid locked so that you cant tell what the problem is. What morons would put a lock on the lid? Its not like someones going to take a jacuzzi bath!Restarted the POS again, and exactly 24 minutes left on the wash cycle, there was another crash. Both times, exactly 24 minutes. NEVER BUY FROM WHIRLPOOL!

We purchased a Whirlpool Cabrio Washer and Dryer in 2007. The washer sounded like it was going to take off and started leaking water. Two repair techs later, we found out it was the center bearing. They actually laughed and said they saw it all the time. It could be replaced (you need to replace the whole drum) for $300-$500, but I was told it would never be the same. I spoke with Whirlpool numerous times and they said they would do nothing, and I should have purchased the extended warranty. All I ask is for a company to stand behind their product. Im very disappointed.

We bought a Whirlpool front load about six years ago. We have had nothing but trouble with since we have owned it. First, the sensors went out on it. We had to pay over $300 to have that fixed. Then, it wouldnt run right. We had to pay another charge for that. Now they tell me the water valve is bad on it. If I had known at the time the problems I was going to experience with this washer, I would never have bought it. I fell for the price. We paid for it. We should be getting better service from it than we are. I could have bought 6 regular washers for what I paid for this one that doesnt perform like it should.

Cabrio Washer - I am so disgusted with this product. After only a few months service came out and the repairman told me it was normal for a load to run for 8+ hours. Second repairman replaced the circuit boards and it has lasted 11 weeks. Now it is not working again. Calling tomorrow. I have a bad feeling about what the end result will be. Expect I will be buying a new washer, will not be a Whirlpool. Just went and tried what another reviewer does to get it to run... Pause/start/pause/start. After 8 tries it is now running. I will not live with this. Not going to spend a dime to fix this piece of garbage. Still have 36 days left on extended warranty.

In March 04 2014, I purchased a Whirlpool washing machine. After having had a Whirlpool for 17 years without any problems with it, I purchased another one. This last one is a piece of junk. I dont even want to talk about the noise, I think it is expiring or on its last leg. They should fire the engineers that invented this model and bring back the other engineers that invented the one I had for such a long time, they far surpassed these space scientists that they now have. On August 8, I called Whirlpool, they sent me someone from Dinos appliances. This man tells me that there is nothing wrong with this machine and that he re-calibrated it. Whatever that means, it is still not wringing the clothes properly. There are only 2 people in my household, so my loads are not very large. I even tried this Drain & Spin cycle after the wash was completed and the clothes still came out too wet. I also have a Whirlpool Dryer and I will not replace it with the same brand. I also will never buy a Whirlpool product again and will make sure that I will share my experience with everyone I know.

I love the brand. I just do not care for the lock lid on all the new washers. I could do without it. I do not have kids to worry about getting hurt. Im looking into finding a brand without a lock lid. I just replaced one before this one. For the lid breaking.

Whirlpool Cabria Washing Machine hold down switched failed in just 18 months of use. It took the Technician 5 days to serviced and repair our Whirlpool top loading washing machine. The washer is till acting up and stop working unless you put a weight on the top loader cover.

I wish I had gone on this website and read the reviews before I bought my washer about two years ago. I thought the Whirlpool Cabrio was going to be a good machine because of the brand name and because it is one of the more expensive washers. Like many others have said, I am disappointed with this washer. I bought it because it has a large capacity, but mostly because it has a hand wash cycle and a deep water soak. I have found that the only cycle that actually may get clothes clean is the Bulky Items cycle, because it actually covers the clothes in water. Some of the other cycles dont even get the clothes entirely wet. And the deep water soak doesnt wash the clothes, rinse them, or spin them dry. I might as well pre-soak clothing in my laundry tub, and then put them in the machine to wash them. Prior to this machine, I had a Maytag Neptune front loader, which did alright, but it had a few problems. I am ready to go back to the inexpensive agitator machine my mother used to have, if anyone still makes them. They at least got the clothes clean, and you could soak clothing if you wanted to. Im sorry that I bought this expensive washer. I wish I had bought a relatively inexpensive, simple machine. One good thing about this machine though is that I was able to wash a sleeping bag on the Bulky Items cycle. So, I didnt have to take the sleeping bag to the laundromat. Whirlpool needs to improve this machine or go back to the drawing board and create a new one.

Cabrio - In Dec 2013: Ran the Clean washer cycle and it would not cut off. I had to shut off manually. Called the company and they sent a technician, who said he fixed it and that everything was good. Fast forward to Feb 2015: Tried cleaning the washer again. When I left the house there were 10 minutes left in the cycle. When I arrived home 7 hrs later, the washer was still running and my hot water heater had cut off. I had to reset via the circuit breaker. This will be my last Whirlpool appliance for a long while.

I purchased a washer from Whirlpool through Home Depot on August 7, 2014 and on Dec 31st, 2014 the washer broke. I called Home Depot and was told to call Whirlpool since I was still under a year warranty. After numerous calls I was referred to Advantage |Appliances, a company that provides repair services for Whirlpool. After a week the technician showed up and briefly inspects the machine to conclude that there were two problems with the machine: The controller is defective and there might be another problem since the water is not draining. An order was placed for the part and another week went by with still no part. I called the corporate office only to hear that it might take 5 to 7 days to receive it. In the meantime I had laundry piling up. I was forced to go to the laundromat with one arm in a cast and a painful lower back. I finally received the part on Friday and the technician arrived on Saturday to install the part and then announces that she was willing to fix the water pump but had to get paid in cash since this was not included in the warranty. Now mind you! This woman knew about the problem from her last visit but made believe that it wasnt a problem. Advantage Appliance makes money by extorting their customers out of money. This young lady stood there without blinking asking me to pay her $89.50 to do the job she was suppose to do in the first place. I purchased an extended warranty from Home Depot only to find out that they would not be able to do anything since I was still under warranty. I have never been so angry and want Whirlpool to take responsibility. I am sitting with a washer half full with water and no one is stepping up to do something! Whirlpool is disgusting! The corporate office was not friendly or nice about this situation. They dont care! Why do businesses like Whirlpool get away with this? This is not acceptable.

We purchased a Cabrio model WTW6600SB2 washer, it has lasted 4 years, then when the pump went out, we paid $200. To fix it then on the 2nd load, it went out, now the tech man says the motor is cracked and Im not sure if the motor is replaced, it will even work. I looked at the motor and it is made of plastic! Can you believe this? Plastic! I didnt believe it until I saw it with my own eyes. I will never purchase a Whirlpool appliance again nor will any of my relatives or friends if they ever ask my opinion.

Purchased Whirlpool front load washer 2010. Had it repaired 2013. Paid $599 for washer & $648 for the repair. Mailed copy of sales and repair to Whirlpool customer service. Received call from customer service and was told to have a nice day.

I purchased a Whirlpool® 4.5 cu. ft. Front Load Washer with Load & Go Dispenser in 2017. By August of 2020 the washing machine was no longer working. The machine would continue to fill with water and not shut off. The machine would then give an error of E01 and F03 and drain all water within 5 minutes of the wash load starting. I had a certified Whirlpool technician come and diagnose the problem for $99. The technician said these error codes happen ALL THE TIME on Whirlpool washers. The technician tried to replace the water pressure switch with no success. He then spoke to a corporate office and was told we would have to replace the motherboard for over $500. The total cost for the diagnosis and repair was almost the exact price I paid for a new washer just 3 years earlier. I will NEVER purchase any Whirlpool appliance ever again.

Im so tired of the mold smell that never goes away, even after following their cleaning cycle many times over. I dont know what to do but I spent extra $ to purchase my washer and now this!

This washer (Cabrio 6th Sense Washer) is less than 4 years old and now needs $500.00 worth of repair. You have to replace the tub in order to replace the bearings. If your washer starts to make noises during the spin cycle, you are in for a big repair bill. I still havent decided if I am going to repair it or junk it. The towels always smell sour even if you wash them twice.

Whirlpool has been a well known brand for many years producing well made appliances. With strong customer support and appreciation. I myself have owned many appliances made by Whirlpool from Fridges to Washers and Dryers with no problems.

This washing machine has been nothing but a problem from the beginning. Theres always something wrong with it. Things that cost so much should last much longer than a couple of years! I have to clean out the drain about every 3rd time I use it or it wont spin out as well.

Last July 2010, I bought a Whirlpool Washer with model # WFW975OWW01. It broke down Sept 2011. Fourteen months so its out of warranty. I paid a serviceman $136 to tell me it needs $1,350.00 worth of parts and service. I sent an email to Whirlpool for help but no response.

I purchased a new Whirlpool 3.6-cu ft Top-Load Washer (White-On-White) Model #: WTW4800BQ from Lowes on 11/1/14, which was only 3 ½ years ago. The washer began making noise during the spin cycle so we called for service. The technician claimed that the bearing pack needed to be replaced and the repair would cost $400. This amount is $20 higher than the amount I paid to purchase the washer. Because the warranty is only one year, I contacted Whirlpool today and spoke with a representative. The representative said they could repair it under the warranty. When I asked how to proceed, she then asked me if I had an extended warranty. When I replied that if I had an extended warranty, I would be using it. She declined any assistance. I now have to purchase a new washer after only 3 and ½ years. I own 10 rentals. I promise that none of them will ever include a Whirpool product again.

I bought a Whirlpool CABRIO washing machine. I was assured it would do large & bulky. I didnt realize that being so called energy efficient meant that it didnt put enough water in to get my clothes saturated! On large loads or bulky items when I put in my laundry detergent only to find out I had to try to wash them again. Parts of the clothes would still be unwashed & dry after going through a whole cycle! After washing the clothes that did get clean comes out looking like I took them to a stream and washed them on rocks. After taking care of my clothes so they didnt look as old as they were, they are now faded & old looking. I hate this washing machine!

Whirlpool Cabrio Platinum Washer - I have a 2 1/2 year old washer that has been serviced twice. This week 10/2/14 the service technician informed me that we had a bad tub bearing. The bearing failure caused a leak which corroded the rotor & stator. It was more cost effective to buy a new washer than to repair our unit!!!! Ive never heard of a washing machine needing to be totally replaced after 2 1/2 years. Any ideas how to deal with Whirlpool?

Cabrio WTW8200YWO - We purchased this washer five years ago. About a year ago it started getting noisier and noisier on spin cycle. Now it sounds like a jumbo jet taking off. A Google search quickly revealed this is a ubiquitous problem with these washers. As we are in our 70s and dont have kids at home, we are very light users of the washer. First, I would suggest that no one buy this washer. Second, I suggest that Whirlpool should recall these washers. I called Whirlpool and it turns out they clearly know about this issue. The good news is they will offer you a discount on repairs or even on a new machine. The bad news is it will still cost you several hundred dollars to fix their design defect. I suggest that you avoid purchasing Whirlpool products both because of their defective design and because of Whirlpools unwillingness to take responsibility for these problems.

The agitation is too loud. I called Whirlpool customer service and said I wanted to return the washing machine because it was so noisy. Whirlpool customer service agreed that it was noisy and said they would send a technician out. Whirlpool customer service never told me the technician they were sending would cost me 25% of the washing machine cost. The technician said this is normal all machines are this loud. Now I am out the cost of the washing machine plus the cost of the technician and all I have is a very noisy washing machine. Im a real satisfied customer. The machine was bought 12 days ago.

whirlpool Cabrio Washer - I replaced my front loading Duet with this, thinking I was done with front loader. Designs are set to fail, liked the idea of no agitator, thinking can clean a lot clothes at once, boy was I wrong, heavy loads wont spin dry, forget sheets or blankets. The machine just stops, leaving everything soaked and you basically screwed, you can invoke a spin cycle but to help make rinse and spin out, sooo disappointed. Whats wrong with the designers of this product? They didnt try sheets to see if it would even work. I am far from over loading this too. Dont buy this.

This washer never worked right. It simply mixes the clothes up with little water. A real piece of crap. See the 2000 other complaints. Time for class action suit.

The washer never uses enough water ever. The clothes are not clean and it sucks! The clothes are half dry when agitation is going. The bulky setting doesnt clean the clothes either. Ive tried every detergent on the market to see if it would help. No different results. I paid a lot of money in 2015 for this washer and Ive had bad experiences ever since. No change in my water bill since I have to usually wash clothes and towels twice. I want my money back so I can buy a better washer! Im beyond aggravated! I have looked for my receipt but its been awhile. I did get insurance on it. I bought it at Lowes it should be on my card they scan.

I bought this nightmare machine one year ago, and stop working. If I try to program a cycle it put itself lock so I can not use or program any cycle. I can not open the door and start a noise like it was draining without clothes at all. And when finally it ends, the machine is like dead, no works, no programs no nothing. I am sick of this appliance. It is almost new and just does not work as it should be. But the worst is customer service, OMG. They lie about everything. The technician came to see what was the problem and told me it was the card, so he could not do anything until the factory send the piece to the place where I live. Well this happened one month ago and I am still waiting for the service. My guarantee was still on time, but every day at customer service they have a excuse/lie that the piece is on my way and service will be completed. Well I am still waiting and nothing happens. I am desperate. No one cares about the customer. If I would have known or read the bad reviews about these washing machines I would have never bought it. I got it at Walmart. I regret deeply. I do not know where or what else to do. Nobody cares or listen. Shame on you Whirlpool.

I purchased a Whirlpool washer in 2005. After the extended warranty expired, our washer broke. The Whirlpool manufacturer did not have parts in stock. It’s on backorder, so what does that tell you? So we have had to wait for over a month for the repair shop to receive parts from Whirlpool’s manufacturer. Service is very slow and the quality of product is very poor. After five weeks and no repair parts, we are going to have to purchase a new washer since we do not have our washing machine repaired yet. I promise to never purchase a Whirlpool product again.

We bought our Cabrio set 2 yrs ago. They have worked fine, until about 4 weeks ago when we begun getting what looks like bleach stains on our dark and colored clothes. I blamed my wife for using bleach or splashing it accidentally. So today it happened again, and no bleach was used or even open near the machine. This was the third load today and the first one was towels, no damage, 2nd load whites and light underwear with some spotting, third load pair of pants and pair of shorts ruined. What is happening?

Mine is a stacked unit...saves space and I just love the stooping over factor... BUT, its an energy saver and I always have to add about 5 gallons of water to it for it to cover even half a normal load...ugh!!!

Whirlpool washing machine model WCW4950XW2 - We have a barely two year washing machine that we purchased at Best Buy and it no longer drains or spins. After $100 repair call we were told that this is a common problem with this model. It is a transmission problem, and with the way the machine is built a repair person cannot get into the transmission to fix it. He suggested we buy a new washing machine. This is a travesty on so many levels! If whirlpool know it has a problem it should offer a partial refund for the purchase of a newer better machine. I keep thinking about what our landfill in this world look like with the proliferation of appliances that are engineered to last a year or two. I can guarantee you I will never purchase any Whirlpool produce again, and I will research whether other brands are associated with the whirlpool brand before I buy it. Sad that a once good company has gone to hell.

Model WTW7600XOW, installed 12/9/2010. For about 4 months this washer has sounded like a jet plane when spinning. I called Whirlpool to see if it was recalled or what they recommended. They provided 2 repair places near me. The repair shops recommended buying a new washer since the repair is so costly. A 4 year old washer used by 2 people should have bearings that last more than 4 years.

We bought our washer (Whirlpool Cabrio) from a rent to own company about 2 years ago, and finally got it paid off. About a week ago, the lid started sticking when it was done washing. I went to open it last night to start some laundry, and it BROKE. Now theres a piece stuck in the bottom part of the lock, and the washer wont start. Anyone else have this issue?

Very unhappy with my top load washing machine. I use more water. Can wash fewer clothes and clothes do not come as clean as with my older Whirlpool. This machine needs a SERIOUS AGITATOR. Will not buy another Whirlpool.

I have been using this brand for many years. My first washer lasted for 30 years..so I will stick with what I know is reliable. It is a great machine. Very simple. I dont need anything fancy. 3 different cycles to choose from.

I bought the HE Whirlpool Cabrio 2 years ago. It has all the bells and whistles, fancy cycles, etc. but doesnt clean ANYTHING. I have to wash three times to get things clean... So much for energy efficiency. It also gets out of balance with larger loads. What a waste of money and time.

Whirlpool Cabrio washer Model WTW6500WW1 Ser C02670098 Type 580 is the worst appliance I have ever had. All the bad comments from people are all true! The washer leaves clothes wet. I get F1 error code or it just locks up and I have to unplug it and plug in again, twists clothes up and doesnt get clothes clean. I have always bought Whirlpool appliances because they were good but this washer has changed my mind about Whirlpool.

All of sudden without any notice there was such a clatter. We dashed downstairs to see what was the matter. My washer Cabrio was on its side off balance. I hollered what is the matter. We sit it up, see the back side bulge out and with some searching we discovered the balance thingy was broke. Now I bought April 2012 while going through Chemo May 2014. I burying my washing. Call Whirlpool. Well they say I file this away sorry about your luck - lol. Do not buy this washer unless you want another one in two years junk and they will not help. Well they will if you give them more. The 1400 dollars I already gave them for the set is not enough.

We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.

In addition to that I find the HE rating a joke as it takes 2+ hours to run a load of whites despite it saying on the read out that it will be 1 hour and 4 minutes, it literally tears up my clothes. I have now gone through 3 sets of sheets, 4 towels, 5 baby onesies... How can a washer that doesnt have an agitator cause holes and shredding in a garment? I honestly dont know what to do anymore. It takes two days to do the wash for 2 people when I could get it done in hours with my old machine. And to think I spent close to $900 on this washer makes me sick! I want to go back to my old agitator type washer from Maytag!

I have purchased 2 Whirlpool washers in the past 6 years. Both have been a huge disappointment in quality and dependability. The 2nd washer I bought May 8, 2015 had problems from the initial purchase. In just a little over 2 years I have had to replace the suspension rods, and now the transmission is broken. Both washers had transmission problems. I have bought my last Whirlpool products. I recommend persons considering buying a Whirlpool product check the reviews before you purchase! I cannot believe this company continues to survive.

This is the worst washing machine Ive ever purchased. Bought 12/19. The water level never never goes up high enough, to cover the cloths. I have to add water no matter what setting. I hate that. The sensor isnt working. You arent able to adjust it yourself, its computerized. The water shuts off when you lift the lid so you cant rinse out the soap or fabric softener caps. I hate that. The lid locks when the rinse cycle starts so I have to unlock the lid to add fabric softener. Why lock the lid so soon, wait till its in spinning mode. Really really badly designed!!!! Will never buy anything by Whirlpool ever again!

Cabrio washer - What a piece of junk! My washer is 2 years old, it now does its own thing - stopping when it wants, doesnt finish cycle, beeps finished and the clothes are so wet and the washer is not emptied. Then, I put it on drain and spin. One time, it kept going for almost an hour of off and on. My clothes were so out of shape and that was on low spin. I finally took them out and put them outside. The clothes from day one have always come out so wrinkled and that too is on low spin. Im afraid to use high spin. I know you have to for towels, but it still does not drain. It shuts off and on when it feels like it. My first contact with Whirlpool was, Well, did you buy the extended warranty? I hate it when asked that when purchasing any product. Its like saying, This is a piece of crap. Im warning you now so buy the extended. So right there, I felt Whirlpool isnt willing to help. What else can we all do here? Please advise.

As I write this my Whirlpool is roaring because a bearing is probably going bad. Ive owned this washer for maybe 5 years. They designed this washer poorly. If you leave change in your pocket as everyone does then it will end up in the bottom below the basket and get trapped. And it dislodges, and it will, when the drain pump engages it will blow the coin through and it will break the plastic housing. It needs two beads so that NO COINS can get through if you wash them. Very disappointed customer.

We purchased our Consumer Reports rated #1 best washer, seven yrs. ago with a five-yr warranty. We have had nothing but repair after repair starting in the first year. The mother board replaced twice, the entire inside had been replaced within four years. It is only a household of three, the washer looks like new! The machine is now making a noise like a freight train... We had a repairman out $95.00 just to look at it! Cost of repair $1,116.21!!!! More than what the machine is worth. The replacement parts wore out in the last 2.5 yrs, again poor design. I contacted Whirlpool during the last repair issue and demanded a full replacement. The customer service rep, as RUDE as can be, checked with her higher-ups and said they would replace it for $845.00!!! WHAT A JOKE. I could buy a new one for that! The repair person said they are one of the highest repair units and the most costly out of warranty. He had one with the same issue just two days prior. I will never buy another Whirlpool product or purchase from H&H Gregg. They sold our warranty twice losing all of our repair records! It looks like I had an extra load size dumped on me!

Purchased this washer 7 months ago. We are a family of 5 with A LOT OF LAUNDRY!!! I adequately researched a machine that could do large loads of laundry, WELL. I read at least 100 reviews and went forth. (Note to self that anyone giving this machine a decent rating, is a DIRTY, SMELLY, FILTHY LINEN WEARING FOOL who doesnt take much pride in their clothing cleanliness.) I proceeded onward and after paying A LOT OF MONEY for this 4.8 Whirlpool Cabrio Washer, I found out within the first two days of owning it, that IT IS GARBAGE! Regardless of the 4.8 drum size, you can only fill it less than 1/4 of the way with clothes, to even hope they will be touched by water. My clothes come out DETERGENT STAINED & DRY! Insanity... A washer that doesnt wet the clothes!!! We have had 4 repairmen come out within this time, because I am fed up! I have been physically shown and told now, by all 4 guys, that the washer will not fill more than 9 inches with water. They advised me to fill Home Depot buckets and throw them into the drum. THIS IS WHAT I DO, TO SATISFY THAT I AM WETTING MY LAUNDRY - PURE CRAZINESS! The repairmen told me to set all loads to bulky sheets + extra rinse + highest soil. This is a 1 hour, 26 minute initial setting. Note that my adding water messes up the computer readings and it will reset throughout the washing cycle multiple times. Even with all of this... the machine still doesnt wet the clothes!! The top and center of the load is BONE DRY! This machine will not wash sheets, blankets or comforters, either. Dont waste your time trying!!! Dont be fooled by the drum size. Your great grandmothers 1930s 1.6 cu ft washer washed more clothes in any given load. #1 My water bill is through the roof. #2 The washer constantly resets and runs on any single load for over 2.5 hours AND #3 MY LAUNDRY PILES HIGHER AND HIGHER, as you cannot put more than a smattering of clothes in the machine, at any given time! GARBAGE, GARBAGE and MORE GARBAGE!!! I would be better served to find a stream and a flat rock and start doing my laundry colonial day style! I am done... Finally had enough of this insanity! RETURNED THE MACHINE THIS MORNING!!!

If 0 stars was an option, I would have chosen that. Ive had my own home for 34 years and have had many washing machines over the years. My Whirlpool Cabrio is absolutely the worst washer I have ever encountered. It doesnt get clothes clean and constantly gets out of balance. Whirlpool did a service call and said it is functioning as designed so I was unable to get a replacement. I really hate being wasteful and adding a huge appliance to a landfill but I will be replacing this machine as soon as it fits into my budget. I dont have a receipt to submit because it was purchased by my builder at my request. Do not buy this machine!

I will never buy another Whirlpool again or recommend them to anyone, and discourage anyone from buying one. I bought a Cabrio washing machine just over 2 years ago and yesterday I received an F51 error code. The manual says that this code requires a technician to come a check for repairs. Well, before I do anything I google the problem, and lo and behold there are thousands of complaints about this issue with the Cabrio models. Some saying that what needed to be replaced were a control board ($280) and a rotor (unknown amount), not including the price of labor. Some said that Whirlpool knows about this problem and they covered the parts and repair. This didnt get my hopes up, but I called customer service and of course they said that there were no reported issues with the model and that what I found on the internet was probably an older model. Of course! The lady on the phone told me that they would not cover the costs and it would be anywhere from $300 to $500 depending on the route I wanted to take. That is a 1/3 to 1/2 the price I paid for the machine. This is ridiculous! I am tempted to just get rid of the washer and go with a better company that actually cares about their customers. This error code was definitely something they know is a big deal if there was nothing I could do about it other than call a technician. I paid almost $1000 for a machine that has barely lasted 2 years before I have to pay money to have it fixed. Not a company I would ever purchase anything from again!

I have been blessed with my washing machine. I have never had one problem with it. I have had my machine for over three years now. It is a reliable machine, with five different water levels from small to super. It also has three different water temperatures (just great). I am very pleased with my washing machine. I cannot tell you how many machines we looked at before selecting our Whirlpool, thank goodness we did.

The Whirlpool duet model wfw9150ww01 washing machine is a piece junk. After using it for two years, the bearing has gone out on it and it sounds like a freight train. It will cost $600 to repair it. We only paid $575 for it. What a rip off. Whirlpool makes junk only. Buy something else.

I am very disappointed in my Cabrio washer. I have had it for two year and now I have to spend $ 250.00 on a machine that sounds like Im in a machine factory. It is so loud in the spin cycle that you cant hear a TV or radio. Also the lit of the washer broke in the start of the second year. I had my previous washer for 15 years before requiring a service call. I have to agree with all the reviews that this washer should be recalled. Maybe if we all call the media in on this problem Whirlpool will be forced to pay for a recall or repairs. Another case of big business ripping off the consumer.

My model # is WTW4800BQO. Purchased 05/20/14 and, under warranty, had repair come several times and they finally supposedly replaced the brain of machine and said nothing further could be done. So all this time I operate the machine manually - timing everything from wash to spin. On all cycles I have to manually - actually turn off machine when first wash is completed and reset to rinse and spin otherwise it only partially fills and drops the water right away on the 1st rinse (besides also dropping water on 2nd rinse). Also I came home one day, after completing a wash load earlier, and found the machine filling up with water automatically so now I always have to be sure the machine is unplugged when washing is completed.

Seems to use very little water. When I take the clothes out, they are bone dry in places which means they havent even seen any water! Clean (?) clothes end up smelling musty and I end up having to wash them two or three times which completely goes against any eco argument! I am really disappointed with this product and would never buy Whirlpool again. I have just washed our dog blankets. The cycle finished so took them out, had to check that the detergent had been used as the blankets were almost completely dry. The blankets still completely smell of dog so have had to put them through another wash (with more detergent – waste of money) and with a pre-wash cycle. Rubbish! We also have a Whirlpool drier and that is no better. Washing never comes out completely dry. It always has to be fully aired, sometimes more than others. There is no consistency in how wet or dry the clothes come out. Avoid at all costs.

My machine has been ripping clothes for a few years but I thought, initially, that it was a snap, zipper or hook causing the problem. I recently got fed up and found this: **. It makes it pretty clear that it is a manufacturing defect. I called their customer service centre and spoke to a supervisor that told me it is normal wear and tear and that perhaps the glass in the door had worn out. Yes, thats right, she said maybe the glass has worn out.They are offering ZERO assistance in what would be a $500+ repair for me. Admittedly, my machine is five years old and out of warranty, but to me, when the repair is to install an entirely new style of door so that the clothes no longer get caught underneath, it is a defect. 43 different models of their machines are included in this issue and it was identified in 2012, a year before my machine was made. Why didnt they correct it before that?

Everything I have read is what I am going through... First the clothes didnt come clean. Lint piles on everything dark... Then at 1 yr and 7 months old, the drum and spin mechanism breaks. It cost me $333 in labor... Should have cost me nothing as far as Im concerned. 2 weeks later, its putting a code up that the hot and cold lines are crossed. Nope, its the whole computer board. Whirlpool again said they will just pay for parts... piece of crap. I paid for the best... Sure didnt get it.

I bought a washer from Lowe’s Home Improvement in September 2017, called a couple weeks after the purchase. They sent someone to repair machine. It is still not working. Called Lowe’s back. Was given an 800 number. Talked with someone at this number got nowhere. Was given another 800 number. I am waiting to find out what is going to be done. This is terrible customer service.

I purchased a Whirlpool Washer/Dryer set in June 2014. Yesterday, Sept 9, the motor stopped working. The machine was on but nothing happened. Called the repairman who said the motor burned out and had to be replaced at a cost of $180 plus $75 for his labor. I paid around $400 for it a little over a year ago and now I have to pay $255 to get it repaired which is ridiculous for a ONE YEAR OLD machine. I will never buy Whirlpool again. I should have read the reviews first before buying but I always thought this was a good brand. Lesson learned, never buy Whirlpool.

This washing machine is terrible. It barely cleans my clothes and frequently gets off balance. I am now on my second repair call in less than 3 years. (I bought the unit in the summer of 2013. It is now the winter of 2016.) The last repair guy tried to blame me, suggesting that I was filling it too much and with heavy materials. Last night, I washed 5 or 6 doggie towels. Not even large, bath sized towels. And the whole thing just stopped. It wont spin and wont unlock. What a piece of crap.

Whirlpool Cabrio HE washer - Purchased my set in 2007. Has not worked properly most of the time we have owned. Lid locks our clothes in when the machine malfunctions and we have to barter with the machine for hours of Google suggestions to get the clothes back out. Still dirty. Or still soaking wet, not spun. Ive never seen so many error codes from one machine. I would never purchase this brand again. The only pro is the load size, which trust me - we have spent more time, water, energy & $$$ with the washer not properly working than the large capacity has saved us.

Ive always had a Whirlpool washing machine and it has been extremely dependable. I have not had any problems with my Whirlpool washer. A Whirlpool has came a long ways with their pricing. It was very affordable for somebody like me and I cant afford a lot but I could afford this. I was very pleased with my purchase and with the product. They havent let me down so far.

I just love the durability of my machine and the features that it offers. It does a great job washing my clothes and I feel like its a solid appliance that lasts for many years and its good quality for the price.

I wish I could give negative stars! My Cabrio Model #WTW6600SG2 sounds like a jet airplane on the spin cycle (this started 2 months ago). Now, Im getting the UL error, its not an an uneven load!

I suppose the idea was good - less water. However, when you are washing clothes, water and agitation are key. Without an agitator, clothes are just spun around with water and detergent. This washing machine (WTW4950XW2) couldnt clean any dirt off clothes. Clothes go in dirty. They come out damp, wrinkled, and dirty. I got this washing machine free from my father and am thinking I got ripped off. No wonder he gave it away. Piece of junk.

Cabrio washer - This was a huge disappointment, clothes not clean, sometimes still dry in middle even with small loads! Have had washer just over a year, second time it has quit working! This time it wont even give a code to why it wont spin out! Living on a budget, I cant afford such a shoddy product! Never again will I buy any product associated with whirlpool!

In 2009 I bought 2 (yes 2) machines (one was for our daughter). I also took out 5 year warranties on both (good job I did). Within the first month on our machine the paddles flew off and after a bit of a debate with the insurers we had another machine (same model). Within a short period from date of purchase both machines had a number of faults - circuit boards, weights that came loose! and bearings going. There are other bits but too extensive to list. To be fair to the insurers they were no trouble (it really is the inconvenience of being without a washer and having to schedule time to get it sorted out). I will never ever buy a Whirlpool as all of these (3 in total) have been a nightmare and ours is sounding noisy again (it only had a new drum 12 months ago for bearings - yes you need a new drum for that £200 in all!!) so I am really glad that we have the insurance. When that runs out and the machine is dead (whichever comes first) I think we will will be buying either a Beko or a Samsung that are getting really high ratings. Anyone reading this might wonder why did we buy these in the first place. Well a colleague of mine at work had one and said it was fantastic (she had children so used hers a lot) hence me buying them (and they were not cheap by any means, so thought we were getting a cracking pair of machines....cracking, yes they might as well be as a chocolate fireguard has more reliability...WARNING DO NOT BUY A WHIRLPOOL WASHING MACHINE - IT COULD DAMAGE YOUR SANITY! AND FAITH IN HUMAN BEINGS TOO!!!!!

Its a great machine but the temperature control button is easily moved at times. The machine does a great job in washing clothes. Ive had mine for 10 years now and hope that I never have to replace it.

Purchased Cabrio washer in June 2011; in May of 2014 repairman said tub seal was leaking and new bearings were needed at a cost of $400. The washer was still working, but sounded like a freight train, very loud. My trusted repairman said to purchase a replacement, this time with an agitator (the Cabrio has no agitator). 2 additional points : the Cabrio took 63 minutes to wash sheets; other loads required similar long cycles, something they dont mention with new efficient washers. Also, agitators will no longer be manufactured in washing machines within the next 2 years. : (

On Saturday afternoon, March 31 at 4:30 PM Eastern Time, my roper washer that was purchased on April 17, 2011 overflowed from the top. Water went into the air ducts and completely fried my security system. My husband was out of town at this time on business. The water went into the terrace level of my house and ruined the carpet, walls and ceiling. The restoration and insurance companies came immediately and were a tremendous help. I felt very safe with them even though they were in my house until 1:00 AM Sunday morning. My husband and I visited our Lowe’s store where we had purchased the washer. They told us to contact Whirlpool which we did on Monday, April 2. We were assured by Whirlpool that we would have a Whirlpool employee in our home to fix the washer. We were also told that we could not move the washer. After speaking with a Whirlpool representative, we received an email confirming the repair person would be in our home on Wednesday to repair the washer. During this time, I had to go to the laundry to wash clothes. This cost me $26.00. On Wednesday afternoon when no one had shown up to repair the washer, my husband had to call Whirlpool only to be told that the repairman would not be coming but he would be there on Thursday between 10:00 and 1:00. He arrived at 12:45 and the nightmare began. He had an “I dont care” attitude and if my husband had not been at home, I would have been very uncomfortable. After looking at the washer, he said a part would have to be ordered and it would be the next week before he could fix it. I asked him what I was to do about clothes to be washed. He replied go to the laundry, he was just the repairman. He also said I could use the washer but not to put a full load. On Tuesday night, April 8th, I was washing and I had the washer on medium load and the washer started leaking from the bottom. We still have not heard from the repairman, today is Thursday. Also, my husband and I work outside the home. It would have been so much easier to have the washer replaced but instead we have to wait. We had a washer to be delivered on Tuesday, April 2nd, but we are still waiting on them. Most of the restoration work other than the washer has been completed. Thank you.

We bought the Whirlpool Duet set for $1,000 18 months ago. About four months ago, it started shredding our clothes. I would get them out with holes in them, but there was nothing sharp in the washer. Then the grey outside seal started deteriorating and getting tiny balls of rubber all over my clothes, ruining several white shirts. It always smells like mold. I just went to get my clothes out of it to find out it leaked water all over with that disintegrated rubber from the seal. The seal had completely ripped from the top to the bottom drain for no apparent reason. Now we are replacing the below. We JUST paid it off this month. It is crazy, it is already breaking!

We bought a Cabrio washer four years ago for over 1,000 dollars. It lasted two years. The cost to repair was too high. We bought a low-end simple machine two years ago from Whirlpool. Now we are told it needs a new control panel, which again is going to make it not worth fixing. Two machines in four years. I called their customer service and there was nothing they could for me. The person they recommended to fix it told me it wasnt worth fixing and didnt even come out. I am done with Whirlpool.

Whirlpool top loading piece of junk! I would give it a zero star review if I could! Do not buy this machine!!! I agree with many other reviews. It doesn’t get the clothes cleaned and now a completely doesn’t work. We reset it, we’ve had the service guy come in and replace a bunch of parts on it. It’s past its one year warranty and doesn’t work anymore. Piece of junk! Junk, junk, junk!!! Waste of money. Do you not buy the Whirlpool tub loading washing machine!

I have a front load washer by Whirlpool and a motor stopped working on the drain. When I called them, they told me it would be $200.00 for the part. I dont understand why they dont stand behind there product. What can be done to make these people fix there stuff? This is there product, if they cant do it right, then find a new job!

Whirlpool - good price for pair. I have had this pair for over 10 years and they work good and are reliable even though they were not the top of the line models. Large capacity is a must - energy efficient is also a must. Discounts are nice to get but if not available I will go with a name brand. I want a washer with an agitator not one of the new ones that dont have one. Reliability is the most important factor so repairs are not needed. I want a full size washer with several cycles and all cycles have a cold rinse to save energy. Having a center agitator is a must - cant stand the newer ones.

The machine is two years old. It cost over $1,000 to buy. From the beginning, we have had mold issues with the machine. The entire house fills with the smell of rotten eggs every time we use it. The machine is used daily so it doesnt sit for long periods. Despite all the complaints online about their machines, Whirlpool refused to acknowledge that there is a design problem with the machine. They refused to make any repairs or buy the machine back and their only suggestion was to buy more chemicals from them to use to clean the machine. We have done this in the past to no avail. Oh, they did offer to send out a service company but on my dime. Whirlpool needs to be sued and I only wish that someone would start a class action suit against them. It really stinks when you try and do the right thing and buy American only to have the company not give a crap about their customers or the fact that their product is garbage. About 10 years ago, I had a Maytag front loader washing machine with the same problem. Maytag bought the machine back on a pro-rated basis, no problem, no question. Of course, Maytag is now owned by Whirlpool. Too bad they didnt adopt Maytags customer service policy. I cant wait for them to go out of business - something they deserve.

My complaint no. ** date 11/07/2014 till date 06/08/2014. Its noted solved by services department after 100 calls by me. They Reply no parts available from company so if you buy washing machine, be careful about Whirlpool washing machine.

Whirlpool front loader duet washer WF9400SW01 - I bought this washer brand new in 2007. The rubber ring by the door started to grow mold after 2 years, the washer collects water after wash. Water was dripping down to the drum and sit there. If I forget to check and drain it by turning on in the rinse cycle, it wets the entire floor. And it sounds like a freight train after 4 yrs when it spins. My last washer lasted 20 years and it was a whirlpool top loader. Thought I might get that with this one.. but NOT.

Without being too critical, I would not recommend this washer for medium to large loads or for throw blankets. I have to wash throw blankets 2 to 3 times to get the entire blanket wet even on deep water cycle. I would not buy this washer again.

Yesterday I purchased this Whirlpool top load washer model WTW4816FW with agitator and we installed it at our vacation home and I started a small load to wash. Yikes, it made noises like a machine that is on its last legs. I knew from washing clothes for 40 years that this is NOT right. We, hubby and I waited and listened to this piece of junk to finish the cycle. Thank god I had set it for a short wash. We also videoed this contraption while it was grinding. I called Lowes and politely told them I was returning it. Thankfully they never had a problem with us bringing it back. (This must happen often.) I go back to the appliance department and decide on a Maytag. I noticed that it looked like the junk we just returned. I stood there and looked up the model number online and lo and behold there was a video of it doing exactly the same noise. It was virtually the same machine I just returned with just a name change. Needless to say we left the store washerless until I can research this further. I then found out that Whirlpool now owns Maytag. Thing is I just bought a front loader Maytag for my main home and it works good. It was a replacement for a Whirlpool without a agitator which worked well too. The YouTube videos seem to be washers with agitators doing this. I just wish I could post the video for all to hear. I guess we are all at the mercy of big companies who dont care if they make a good product as long as they can make it cheap.

Purchased top loading Whirlpool Washer WTW5000DW0 10/12/2015 at Best Buys, first no agitator machine for us. Two weeks later I call for repair service because of the noise from tub. Explained in other reviews as earthquake or jet engines. The machine is in the garage and can be heard through the walls into the house. Repair tells this is normal for the machine and it must be our first none agitator machine.I then purchased a extended warranty policy through Whirlpool. 12/13/2016 machine no longer washing clothes. Call Whirlpool for service. Repair came out 01/17/2017 (a month later). Washer plate had to be replaced. The gear was completely shredded. Not in stock, waited 2 weeks to get repaired. Tension springs on outer tub replaced at same time. Was told the excessive grinding and bumping of the tub was not the reason for the gear shredding.06/30/2017 same problem, I set a repair date 07/01/2017 between 8:00 a.m. and 12:00 p.m. No one shows and no call. I call Whirlpool and they are sorry and set the appointment the same day for before 5:00 p.m. No one shows our calls. I call back. Already closed. I call the next day. Sets a new date 07/05/2017, 8:00 a.m. to 12:00 p.m. Same problem. I called back speak to a supervisor who says hell get to problem and find out whats wrong. Sets a new date 07/08/2017 8:00 to 12:00 p.m. 07/07/2017 I get a call after 5:00 p.m. that the repairman is not available and can we reset for 07/13/2017. I hung up and called back the next day and spoke to a supervisor I had previously spoke with. He called an outside repair company that Whirlpool uses in this area. New date 07/12/2017. Repairman shows and I explain the washer plate was loose again and I smelled metal burning. I had told my wife to continue to use the machine to wash the clothes. The repairman tells me I voided the warranty by doing this. Im standing in the garage while he has his head in the machine trying to get the washer plate out. He shuts the lid and turns the machine on wash/spin says the machine is ok. We have an exchange of words and tell him I want to see the washer plate gears. He says he cant get the plate out now and I wasnt there for him to show it to me. This continued until he forced the plate off. He called Tech Support to say I voided the warranty. He told them customer claims loud noises and banging. I asked to speak to Tech but he tells me they dont speak with the customer. I looked at the gears on the washer plate and the transmission. Both had metal shavings. He tells me he is going to do me a favor and replace both. Its supposed to take a week. Wait and see. I have asked for a replacement or money for the machine through Whirlpool. I was told there has to be at least 4 repair requests for the same problem and the repairman has to determine that there is a problem or that its a lemon. I will not recommend or purchase another Whirlpool product.

I thought with the big tub I would be able to wash my king size bedding and other large things. Theres barely enough water to wash a small regular wash. Since it has no water it does not clean my clothes. Why the big tub if you cant use but one fourth of it?

My elderly mother purchased a Whirlpool Cabrio washing machine in 2013 (Model Number WTW8600YW1). It never filled properly with water. It evolved to a sensor and circuit board issue that Whirlpool never totally remedied. Hence, the machine never worked properly. This 800 dollar purchase on an elderly persons limited budget had to be utilized minimally. Now fast forward in 2015, even with minimal usage and white glove handling, the machine is displaying an F51 error. You guessed it, Whirlpool will not remedy the issue, although it is well-documented to be a widespread complaint hence clearly a product defect. Shame on Whirlpool, their business practices, and what amounts to theft of an elderly womans finite income. I have advised my mother to trash the useless Whirlpool appliance and purchase a Kenmore washing machine, of which I have been the proud owner for 10 years, doing laundry for a family of 5.

Me and my wife bought a Whirlpool top load washer June 2011. Two months later the motor locked up and they repaired it; then the transmission started whining the next month. It was repaired. Now a bearing is going out all in the first seven months of ownership and they will not exchange washers, they just want to keep fixing this one until the warranty runs out. Whirlpool washers are a piece of junk and I will tell everybody not to buy anything Whirlpool.

The washer (Cabrio WTW7800XWO) was less than 2 years old and we had a motor go out, so we paid a repairman to come out and repair the machine. The total cost was over $300. Now 2 months later, we get another code on the machine and Whirlpool says, We are sorry but there is nothing we can do, but if you would like to pay $219, we can get a repairman out there to check out the machine and repair it. Theyre also giving the machine an additional year warranty. Shortly after that, I noticed the lid was not staying up when I opened to put clothes in it to wash. So since I was wondering what was happening, I looked at the lid and to my surprise, the springs that hold the door up when open are built into the plastic lid cover that has a see-through glass on it. Right where the springs are located, it must be a stress point and the plastic lid has since cracked and is almost about to break off. I am now in the process of ordering another lid and Whirlpool offered to sell me a lid for $226 but I think I shall buy it from someone else as I dont want to put any more money into Whirlpools pockets. We paid over $1000 when we bought this machine. Now it is about 2.5 years old. I hope there is a class action lawsuit on Whirlpool as I will definitely join in if there is. This company needs to go out of business if they continue to sell machines like this that have so many problems especially when they are less than 2.5 years old. Goodbye Whirlpool. You have lost many more customers as I shall be letting everyone I know about all the problems and complaints about this machine.

I purchased a Whirlpool duet front load washer 1/2013 new from Lowes. In 5 yrs it is my 2nd washer of Whirlpool. After 2 1/2 yrs, the bearings have gone out, also every time I run the cleaning cycle, water leaks out under the washer. My boyfriend looked the parts to fix the washer, since I called Lowes concerning the warranty and its out. Cost to repair, just in parts would be around $400, I paid a lot of money for a product to last only 2 1/2 yrs. Such a lack of quality in workmanship. With these price, there should be better quality. Do not purchase a whirlpool. 2 washers for them in 5 yrs is not a great track record.

This is Whirlpool model MVWP835DC2. I bought brand new. Recently used about once a week. Got an alarm that indicated no communication to core unit. Talked to Whirlpool service and unit is out of warranty (20 months) and advised I should use authorized service company to come and diagnose. This took 2 weeks. Service man came, washer did not power up. He quoted that repairs would be $750 and not worth it, buy a new one. I went on internet and found YouTube videos that showed how to diagnose and fix. I called Whirlpool for new console, $350 and one month. Went to parts house and got part for $250. This fixed problem.I have a few problems with this machine and company. 1) This now turns out to be a known problem with these machines. The console fails. I am not sure how this is going to last 30 years. 2) Service man took nothing apart and could not diagnose problem with no power. He quoted $350 for the console and the balance for the core. He was guessing or pulling a scam. Take your choice.3) Part not available from Whirlpool because so many are failing.Thanks for making a great product.

I bought this machine in September of 2014. Six months later I HATE IT!! It does NOT get the clothes clean and dont even try to bleach white towels or socks, it doesnt pump the correct amount of hot water and things come out just as dirty as when they went in. It tangles everything together and frequently stops working because it unbalances the load with its lack of water. Ive always been proud of how my familys laundry looked and now Im just embarrassed. Im considering donating this to a human society for dog towels. Stay away from this washer, its horrible. Im going to the laundromat and shopping for a new machine ASAP!

The company I work for bought a new washing machine a couple of months ago to make it easier for those that do the laundry here. The washer was suppose to be this great washing machine which has turned out to be the biggest piece of trash on the property!! Every couple of loads you have to turn it off and hopefully the computer in this Whirlpool cabriolet will reset so you can wash a load of clothes. You have a 50/50 chance it will work. DO NOT PURCHASE THIS MACHINE. IT IS THE WORST WASHING MACHINE IVE EVER USED!!

This machine was my dream machine for about two years. Then the noise started during the spin cycle. It gradually got louder and louder, until it got so loud that it sounded like a jet engine taking off. You could not be near the wash room and hear each other talk. Then it began to aggravate me with the UL flashing. I know how to load a washing machine. It was just a defect. Then it started making a grinding sound to add to the roaring spin noise. We were told that it would take over $500.00 to fix, so we just sat back and waited for it to die. Well, the other day it began to leak some water out of the bottom of the machine. Now today we are paying our last respects to a piece of junk that Whirlpool calls a washing machine! It is less than 5 years old. This was a $900.00 washer. There should be a recall. We should ban together and demand a recall! Now I will be forced to go buy a new washer. I can tell you which name brand I will not buy, Whirlpool!

Cabrio washer - I have always had a Whirlpool appliances and have always been satisfied with them, but this is the worst washer ever manufactured. I bought it to wash heavy loads of jeans and it takes me all day to wash 1 load because it is always out of balance. No matter what setting I put it on I have to keep rearranging the load. Without putting up with that, the load takes 87 minutes on bulky wash. That is far too long and then you add all the time I spend rearranging it to get it to work. I think there should be a recall or at least admit you have a poor design. My son works for Whirlpool, but Im not sure I will be supporting this company again.

Overall, I am happy with my Cabrio BUT we purchased a Whirlpool WTW7000DW0 Cabrio top loading washer w/ electronic touch panel in May 2016. We experienced water hammer from day one. I finally had enough yesterday and knowing that the plumbing could be suffering (15 year old condo), purchased 2 Sioux Chief MiniRester, Model 660-H arresters (Lowes at $9.99 each) and had a plumber install them today. I could have but am nursing a fractured rib. Long story short, they work perfectly. There is NO indication elsewhere in the unit that water is even entering the tub unless youre standing right beside it.Ive been told that hammer problems exist in ALL high efficiency washers, all are prone to this problem. I was also told by a Whirlpool support person that the Cabrio is a Samsung design and the pulsing of supply water off and on, over and over is normal operation. If I had been informed when purchasing that hammer is a common problem, I would have installed arresters from the get-go. At the very least, manufacturers should include arresters as a part of the sale; installers should make sure that every new installation includes arresters. All told, I am out just under $200.00 for new technology that really could have been engineered out in the beginning.

Lu ** is a mgr. at Whirlpool customer service. Shame on you for the way you spoke to me. Then giving me a joke # to call... Karma sucks is all Ill say to you. I have to wait on the phone to speak to anyone is over 30 mins. Just to get pushed off to the side like I dont matter. Im trying to get help to have mine looked at to pass the time for another Whirlpool to come to me! Mind you mine didnt last 4 yrs. Yes I was trying to buy another Whirlpool but after this sloppy customer service. You dont need this stress... Stressful enough that these washers dont last anymore. Ya GE AND MAYTAG ARE LOOKING BETTER AND BETTER.

I couldnt wait to get a front loader and hated it. As soon as I saved up enough money, I bought the water saver Whirlpool top loader. I love it! The clothes get cleaner and dont smell musty. Im very happy with whirlpool.