After 2 years the motherboard failed on my Top load Cabrio washer. We had to spend $300.00 dollars to get fixed. When we called Whirlpool to see what they would do about it, they actually offered to sell us the board for $345.00 dollars and a 1 year warranty on the board. They actually wanted us to pay more from them than a local repair service. DO NOT BUY THIS MACHINE OR ANY OTHER WHIRLPOOL PRODUCTS. Also does anyone know of any class action lawsuits surrounding their obvious use of defective parts?

Whirlpool Energy Efficient Top Loader - I re-wash at least 20% of all clothes because they have dark spots AFTER washing them, but NOT before! It is a moving target, wash out one dark mark; get another somewhere else. I bought great quality sheets that are permanently stained, because of this. No matter how you load this machine, anything with arms and legs gets entangled into a big knotted mess. It is difficult to separate them and time-consuming. This puts a lot of stress on the clothes, especially as the load spins. I also re-wash entire loads at least 4 loads because the clothes dont rinse properly. I bought a 5 yr. extended warranty and have had this serviced at least 4 times to no avail. THE PROBLEM IS IN THE DESIGN! I am POSITIVE of it. If you have these problems, as well, please contact me. I would love to investigate a class action suit. I am THAT mad.

My husband and I bought a new Whirlpool Cabrio Platinum Series Washer and Dryer in November 2012 from Lowes. My clothes, especially towels, smell like mildew and mold since I have used it. I thought it was just me. I have even thrown some items away when they smelled so bad. I love doing laundry but this not being able to have clean smells was driving me crazy. I tried everything I could think of but to no avail. Finally in October of this year 2015 my washing machine began to make a loud noise. My husband said sounds like a bearing is going out. I immediately sought a repairman thinking that it would be a simple fix. $420 later I had a new bushing, bearing, sleeve, etc. The machine was still making noises even louder and my repairman came back, this time to the tune of $180. So far weve spent $600 on a washer that we gave a little over $800 for. Now I have a UL code showing up when my load is almost completely done and guess what? My repairman says he has yet another part that should take care of the noise but he wasnt so sure about the panel. He may have to do a little research on that. I think all I have is a repairman that is a parts replacer so we were forced to purchase a new washer yesterday and my Cabrio is sitting in my garage. If someone needs a boat anchor just please contact us. I wrote a letter to the corporate office of Whirlpool before I even knew that so many consumers were having problems. Two repairmen told me that the Cabrios were junk. Most of them belonged in the landfill. Whirlpool customer service called me and offered me a discount coupon on a new washer. I told them that I didnt think I needed another piece of crap. I also questioned them as to why they could foist these crappy machines off on the American public. They had no apologies whatsoever. While researching what brand washing machine to invest in, I realized that there were numerous complaints regarding the Whirlpool Cabrio. With as many consumers who have been taken advantage of with this awful product, why cant someone do something?

This Whirlpool Cabrio washing machine just does not do the job. It smells inside and does not get clothes clean, just normal everyday laundry. I usually have to put them through twice. It is supposed to be a water save, but I dont think it uses enough. I use minimal he detergent, yet you can see detergent residue on the clothes after they are washed, I think because there is not enough water running through to rinse clothes very well.

Purchased top loading Whirlpool Washer WTW5000DW0 10/12/2015 at Best Buys, first no agitator machine for us. Two weeks later I call for repair service because of the noise from tub. Explained in other reviews as earthquake or jet engines. The machine is in the garage and can be heard through the walls into the house. Repair tells this is normal for the machine and it must be our first none agitator machine.I then purchased a extended warranty policy through Whirlpool. 12/13/2016 machine no longer washing clothes. Call Whirlpool for service. Repair came out 01/17/2017 (a month later). Washer plate had to be replaced. The gear was completely shredded. Not in stock, waited 2 weeks to get repaired. Tension springs on outer tub replaced at same time. Was told the excessive grinding and bumping of the tub was not the reason for the gear shredding.06/30/2017 same problem, I set a repair date 07/01/2017 between 8:00 a.m. and 12:00 p.m. No one shows and no call. I call Whirlpool and they are sorry and set the appointment the same day for before 5:00 p.m. No one shows our calls. I call back. Already closed. I call the next day. Sets a new date 07/05/2017, 8:00 a.m. to 12:00 p.m. Same problem. I called back speak to a supervisor who says hell get to problem and find out whats wrong. Sets a new date 07/08/2017 8:00 to 12:00 p.m. 07/07/2017 I get a call after 5:00 p.m. that the repairman is not available and can we reset for 07/13/2017. I hung up and called back the next day and spoke to a supervisor I had previously spoke with. He called an outside repair company that Whirlpool uses in this area. New date 07/12/2017. Repairman shows and I explain the washer plate was loose again and I smelled metal burning. I had told my wife to continue to use the machine to wash the clothes. The repairman tells me I voided the warranty by doing this. Im standing in the garage while he has his head in the machine trying to get the washer plate out. He shuts the lid and turns the machine on wash/spin says the machine is ok. We have an exchange of words and tell him I want to see the washer plate gears. He says he cant get the plate out now and I wasnt there for him to show it to me. This continued until he forced the plate off. He called Tech Support to say I voided the warranty. He told them customer claims loud noises and banging. I asked to speak to Tech but he tells me they dont speak with the customer. I looked at the gears on the washer plate and the transmission. Both had metal shavings. He tells me he is going to do me a favor and replace both. Its supposed to take a week. Wait and see. I have asked for a replacement or money for the machine through Whirlpool. I was told there has to be at least 4 repair requests for the same problem and the repairman has to determine that there is a problem or that its a lemon. I will not recommend or purchase another Whirlpool product.

My family purchased a Whirlpool Cabrio washing machine approximately 4 years ago. The first two years were fine. I had no issues out of the machine at all. The last two years (just as my warranty expired) have been terrible. It was serviced twice just before the warranty was up and my husband has serviced it twice since. On two separate occasions, the bearings have worn-out and the bottom seal leaks water all over my floors. I would never recommend one of these machines to anyone!

I have always chosen Whirlpool or a Whirlpool product such as Kenmore or KitchenAid. Preferably with an actual agitator in the tub. As a very capable handyman, repairs have been easy and relatively reasonable in cost. My units are 15 years old and going strong.

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

My NEW Machine Top loader HUGE drum. Have problems with clothes not looking like they’ve even been washed, Spun so hard they are twisted all to heck. And white stuff - my oxy powder maybe? Not dissolved. My old machine was a Kenmore 30 yrs old. Thought I’d be able to trust whirlpool but not sure. Am I missing something in the loading process. Seems to read something bout not Covering the knob on the bottom. Is this true?

2 years of use the wash plate went. $150 later, one year later wash plate went again (the wash plate is all plastic, the motor spline in metal total stripes the plastic teeth in the wash plate) I replace myself. 3 weeks later the shift actuator failed which cost another $60 which I replaced. Now the bearing is going. There are only 3 people living in the house. I would stay away from the top loader washers from Whirlpool h2 low series. Huge disappointment.

After 2-1/2 years we started having trouble with the spin cycle on our Maytag washer. We live in an area with no repairman. Whirlpool want us to pay just to talk to us. Now the timings off. It will not spin out.

Havent even had the Cabrio washer for three years & Ive hated it since day one!!! First, our clothes dont come out clean OR come out with white streaks (changed soap, still happened!). Washing bedding is a nightmare! They are sopping wet & I have to wring it out. Finally broke down today & the repairman quoted over $600 to fix (paid $800). Take this piece of junk away!!! It cost me less to replace than get fixed; way to help the environment!

Never again will I buy a Whirlpool product. I paid over $800 for a new washer 51/2 years ago. I had it worked on twice under extended warranty. Now the bearings are out of the tub and it sounds like a jet taking off when it spins. I had whirlpool products in the past and they lasted for years with no problems. I have a friend who has a relative who is an engineer for whirlpool and his job is to engineer their products so they fail within a certain time frame. They dont want them to last like they use to. They now have gotten their product line to the point where they can tell when it will fail. This is crap. What happened to products that lasted like they use to. NEVER BUY WHIRLPOOL.

We acquired the Cabrio Six Sense washing machine through the purchase of our new home, and quickly realized why it was left behind. This thing is pretty and has lots of bells and whistles, but that is where it ends. I am very surprised to find out that Whirlpool put such a piece of junk out for purchase. I have owned Whirlpool products in the past and had great performance and quality. We will be pulling this hunk of junk from our laundry room and installing the GE washer that we already owned immediately. Anyone want a free washer?

Whirlpool cabrio washing machine is 3 years old and the bottom leaks heavy bearing oil everywhere. I now see it is a common complaint and the seal was incorrectly installed by the manufacturing plant. They should be forced to offer a recall and they should stand behind their product. I will never buy whirlpool again. I see thousands of complaints online.

Weve had this washing machine only a few years, and our household of 2 probably averages 1 load of laundry per week. Weve always had the same problem everyone has with the detergent stains on clothing and having to rewash loads, and the only remedy weve found was using the oversized loads setting and rewashing a load. The last straw was 6 months ago. It quit going through a complete cycle and would not spin out without resetting it. Then it quit spinning out at all. Service Guard, a 3rd party warranty company, diagnosed a faulty motor and ordered a replacement. After a long delay Whirlpool advised it was back-ordered for 3 months. A week ago Whirlpool advised them it was now back-ordered until 5-27. They did not know whether wed ever obtain a replacement motor. After taking clothes to our sons house for a couple months to wash, we purchased another used machine to use until ours is repaired. It is beginning to appear that machine may be our permanent machine. This is a pretty sad testimonial about whirlpool. We have always used Whirlpool appliances but appears we may have to switch brands. And it certainly does appear these low water machines are garbage. Very disappointed in Whirlpool.

We bought this Whirlpool he washer two months ago, and it is the most aggravatingly frustrating washer weve ever had the displeasure to use. There are times when it washes just fine, but I always have to put the mode on deep water wash because the normal mode uses very little water (like its supposed to) but it doesnt clean the clothes. However, most of the time it doesnt wash at all. All the lights will turn off and youll hear this sound and itll drain the water without having been in the wash cycle. Worthless piece of equipment! I prefer the old washer where I have more control. Whirlpool used to be such a good brand, What Is Happening? The new design for their washing machine nowadays generates a lot of complaints, and with good reason (because they suck).

Cabrio Top Load Washer model WTW6800WW1 - Although we were very happy with the vendor where this was purchased and happy with the majority of the washer function; there is a problem with the cabinet & lid connectors rusting. Specifically, the lid connector on the left side totally rusted out, and also around the bleach cup, rust. There are also rust spots where the seam of the top section of the washer meets the bottom part. The washer was purchased in 2009. We have had it serviced in the past, prob 5 years ago, it needed a new motor and the rust was beginning to show then, while under warranty. I recently called Whirlpool and the associate told me that she had never received a call with regard to this type of problem. She did give me names and phone numbers of appliance repair in my area. I find it odd that Whirlpool would not make their associates aware of issues like this. I searched online and saw more than a few complaints about rust. So on it goes, no recourse, and as I read about the problem from others reporting this; it was mentioned that the vapors from the bleach cup etc, contribute to the rust. Additionally, even if it was under warranty, I was told that this is considered cosmetic and it would not be covered. Until... and I can only suppose, that until the lid possibly falls off while lifting, the cosmetic ruling may then turn into a function problem. Now there is also a squeaking sound, so off to call the appliance repair, check the cost and next time... buyer beware. I guess a lesson in science as well, hopefully this design flaw will be corrected for the next models in process.

This washer is only a year old and out of warranty. At first I was getting white stains on dark clothes and now I am getting unremovable oil stains on all of my clothes. With the white stains I cut back on dry detergent and went to liquid. It did not help. On black stains I sorted clothes very carefully so that nothing dark or black was in with other color or white clothes, still the same stains. Brand new capri pants ruined with first washing. I have tried cleaning the machine with bleach as recommended, did not work. Whirlpool and Sears deny they have ever had a complaint. Yet there are hundreds of the same complaints on the internet. Is there anything that can be done.

My parents bought a Whirlpool washer machine and the machine was fine for the first two years, then water started leaking from the bottom of the machine and no one has yet to fix the problem! They have the worst customer service department. The A&E worker who came to my parents house smelled, wasted a bunch of time working on the machine and didnt fix anything! The A&E worker visited my parents house over 10 times and the problem still wasnt fixed! They (worker) have ordered parts after parts and still water keeps running from the bottom of the machine! Someone, please help and cut Whirlpool from the stores! Ive spent almost a whole on the phone trying to help out my elderly parents! Its ** and a lot of headache! Never use Whirlpool; theyre all crap!

Cabrio he washer wtw6400sw2 - I bought this washer about 6 years ago at the time we paid around $900. Now my bearings went bad and the repair person told me it would cost around $300 to $400 to replace the bearings and seal and shaft but that I should call Whirlpool and see if they could replace the part or give me some discount cause it is becoming an issue with all the Cabrio washers. So I called and spoke with a so called manager - as far as I know it could of been a cleaning person there. She told me that she could not do nothing about the issue. So if a lawyer would be nice to help me and the rest of the world that are having all these issues to file a suit against Whirlpool Corp.

The first Front load Whirlpool washer leaked. 5 repair techs visits. Wasted days. Finally located the leak, in the main basket. Replaced washer. Second washer the clothes come out smelling like a horse blanket. Mold. Clean the washer every month still mold. Plan on junking the washer a getting a new model. Never expected this much trouble and time on a basic appliance.

We purchased it from Best Buy. It was a good thing we got the extended warranty. They completely rebuilt it two times. In the 6 years we have had the washer. The motherboard went out. The bearings went out. The only thing nice I can say is that it’s a top loader and doesn’t get smelly like the front loaders do.

Our 2005 whirlpool duet washer steel drum and plastic tub broke. My husband diagnosed the problem and opted to fix it to save money. The parts are under warranty but you still pay labor and technician visit running up to $250-$300. The plastic tub was obtained only if we paid for it $100 and the steel drum they sent under warranty. The plastic tub has a hole with a black plug and sensor in it. There is a discrepancy in the measurement of the old tub and new tubs hole that is slightly larger, therefore when installed a steady stream of water leaks out. I now have 3 plastic tubs as that was their solution, to send more of the same that did not measure correctly. An investigation was done to determine they were the correct parts. As asked we had a whirlpool technician come to verify parts were correct and being installed correctly and the parts sent would not fix the machine due to the hole discrepancy. Many calls were made to whirlpool and they continue to give me the runaround. They now are not taking their technicians information. The technician has given the information to 3 sales reps in the new england area and made several phone calls to whirlpool and no one is willing to give us a solution.

A top loading washing machine with an agitator in my opinion, gets my clothes 100xs cleaner than one without. Ive owned front loaders and top without agitators. Never again. Top with agitator is my personal preference from now on. Also Whirlpool has never failed me unlike other brands.

We purchased the washing machine on February 2, 2013 and initially noticed that some of the clothes were still dry when the complete load was over. Meaning that I am not saving water cost because I then have to rewash the clothes and pre-scrub the clothes. Then a little over a year later, the machine is making this extremely loud piercing noise when spinning. The cost to replace the part is $250.00+ the repairmans fee. Whirlpool says there is nothing they will do. From reading the other reviews, this is really sad because of the numerous people having the same issueS with a capital S. I definitely would support a class action suit.

We bought our Cabrio set 2 yrs ago. They have worked fine, until about 4 weeks ago when we begun getting what looks like bleach stains on our dark and colored clothes. I blamed my wife for using bleach or splashing it accidentally. So today it happened again, and no bleach was used or even open near the machine. This was the third load today and the first one was towels, no damage, 2nd load whites and light underwear with some spotting, third load pair of pants and pair of shorts ruined. What is happening?

Bought Cabrio 3 years ago, started getting ul code and f1 code. We leveled machine, but cycle kept getting stuck mid-cycle. Called repair guy, they say it is going to cost between 6 to 800.00 to fix???? Really. Its three bloody years old. Very disappointed. Do I now get it fixed or break down and buy another washer. I would not buy Whirlpool again. Very pissed.UPDATED ON 02/05/2015: We called an appliance repair company and initially paid $440.00. After installing a motherboard computer system, it still did not work. We were then told that the other part would be another $120.00. We were already soaked for $440.00 so we decided to pay. After that was repaired the washing machine was still stalling mid cycle. We were then told that it has something to do with the wiring and it would cost another $120.00-$140.00. Needless to say, we declined. Complained to whirlpool that machine was three years old. We are pissed and $570.00 out of pocket. Just bought a lg front loader and paid for a 5 year warranty!!

Recently bought and had a Whirlpool Cabrio Washer (from Orvilles appliances) installed in my home. The very first day I hated it. Worst purchase I have ever made. I spent over an hour picking hair out of my clothes, and hair was also stuck in the crevices of the drum. This is the very worst machine and company I ever had to deal with. They told me, Too bad. Since there was no mechanical problem there is nothing they will do. I will never deal with either of these companies again. I cant wait to see what the hair build up will do to the machine itself, Had it less than a week.

I have posted on here in the past about the problems with the Cabrio Washer from Whirlpool. Our third top load lid was just ordered since 2011. There is a design flaw where the plastic frame around the lid cracks and causes the lid to hump up. While shopping at a local appliance store recently, I saw a new Cabrio washer and the lid and hinge system has be re-designed. I wonder why?????

In the past 8 years, I have had to replace 2 Whirlpool Calypso washing machines and 1 Cabrio washing machine. All 3 washing machines worked great for the first 2 years. I purchased the Whirlpool extended warranty on all 3 washers. The first Calypso had 12 repairs done on it. Finally A&E repair service deemed the washer not repairable. Whirlpool replaced the Calypso with a new Calypso. Based on the problems with the first one, I again, purchased the extended warranty. Again, after the manufacturers warranty expired, I again had issues. After numerous repairs, A&E deemed the washer unrepairable. I contacted Whirpool warranty service and was told that they would reimburse me 75% of the cost of their choice of a Whirlpool washer! Since I have had 10 hand surgeries, I need a washer that does not have an agitator (hence the original Calypso purchase). The model that Whirpool warranty deemed as a replacement had an agitator and was also a much lower energy efficiency rating. I found that the Cabrio was a comparable replacement model and finally Whirlpool agreed to replace the washer at 75%. I was angry that they didnt cover the total replacement, but felt at least I got a totally new problem-free washer. I again purchased the extended warranty. I got the Cabrio in March of 2008. In April of 2011, the washer started getting rust around the bleach dispenser and also I would get UL code (Uneven Load). A&E tech came out and replaced a bearing. He said that the rust was not covered under the warranty. I asked how it was okay to have rust around the bleach dispenser if the washing machine is always wet with water. A month later, I was still having a UL code and the rust was getting worse. A&E came out again and said that even though I saw rust around the bleach dispenser, the rust was in fact underneath the tub and had eaten away at the parts. He called the warranty company to authorize repairs and the Whirlpool warranty company denied any more repairs on the washing machine.

I purchased my Whirlpool washer on June 28, 2011. Within 4 months, I had to call for a repair. It is now going to be a year and I am on my seventh repair call. The repairs have been everything from loose pulleys, new belts, and new valves. When I called to complain, they said there is nothing they could do and I should take out the extended warranty. I have had washing machines last up to 15 years. Needless to say, they werent Whirlpools. I really would like to have it replaced. I dont think its fair to me that I should have to wait for a repairman to come out and tell me he doesnt have the part and has to come back. I did take out the extended warranty, which cost approximately $150.00 and that should not have to be.

I too expected a whole lot more for the price I paid for Whirlpool WTW5000DW1 HE washer top load. Fuzz, grass, pet hair and food remain after washing. Had a repairman out to look at it. There is nothing wrong with it. He says they do not use much water to save money. Well, if I a have to wash everything at least twice am I saving money? Think. Will look into an old fashioned washboard next time. Frankly I think it is a scam. The HE Tide is more concentrated and my clothes do not come clean! Tried to get my money back from the company that sold it to me and I was told only if I were to buy the $900 Speed Queen. Someone’s making a lot of money from consumers who need washing machines.

Whirlpool Cabrio Washer Model WTW6400SW2 Serial CU0272414: I replaced my wonderful 25+ year old Kenmore washer with the Cabrio, 4 years ago. Within the first year I had to have a computer board replaced that was covered under the warranty. This last 6 months I replaced the suspension rods, was constantly showing that the load was unbalanced. Also have a LD error, long drain, probably because a sensor is bad. Today, restarted a load several times and could never complete the entire cycle. I resorted to unplugging, and starting a drain spin cycle and the washer just flooded my house. So Im done with this unit. Waiting for a class action suit. Lets get started. What type of unit should I buy now. I guess Im going to subscribe to Consumer Report before I buy another. Laundromat for me in the meantime.

When washing towels or a blanket or quilt, anything substantial it wont spin the water out of the laundry. This washer is only 5 months old.

I love my Whirlpool 4.7 cu. ft. top load washer because it has a pretreat station that is super handy for pretreating stains in a handy little place. The agitator is stronger than my old washer and really gets my clothes cleaner. Its also very quiet and easy to use all the buttons. The best feature is the deep water fill that you can select for more water.

Since buying a Whirlpool Cabrio washer about 3 years ago have had several breakdowns. Within 6 months the computer completely failed. Since then it failed again. About every six months it costs me around $125 to get it running. The thing is a piece of junk. If the load is slightly unbalanced it just shuts down during the spin cycle. The old Maytag we had ran for over 25 years with the belt replaced once. No other problems. Will not buy another Whirlpool again.

The washer works well for the age of it. However, I would say it is not designed as nicely as some of the others I have seen. I found it performed okay doing the wash, but it didnt hold up as well I as I would have liked. Seems cheaply made. The machines plastic parts have stained from rust and seem tinny.

Our Whirlpool Cabrio Washer is barely over one year old, and its getting increasingly louder (I cant hear the TV in the other room). I researched this issue and found this is a common problem with the upper and lower bearings. Check it out on YouTube; its easy to find. Whirlpool should buy these back! Is anyone aware of a class action lawsuit against Whirlpool regarding these pieces of junk?

We purchased Whirlpool Cabrio Washer WTW5600 series in October of 2010. I bought the machine from Sears and also bought the extended warranty. Less than 6 months after I had been using it, I noticed that all my husband’s shirts were getting sweat stains under the arms and my hand towels were very smelly after drying with them one time. I called Sears to have someone come out and tell us what the problem was. He said I was using too much detergent so I reduced the amount of what I was using. It did not help the problem so I started using the extra rinse each time I washed, still did not fix the problem. I called them out 3 more times in 2011. One tech told me I was still using too much detergent so I reduced down to 1 tablespoon like he suggested. I stopped using softener in my washer because he said I needed to clean my machine more than one time a month, to clean it every 3 weeks. No solution to the problem still. I have had a tech from Sears and one from Whirlpool (who incidentally was the same man, he was from A&E Appliances). When he came in the door, my husband told him he had been here before and I said 2 times. He lied and said he had not been out before. Are we blind? No. He ran the cycle but sat in his truck while he was running it. None of the techs have ever put a tool on the machine to check if the water level is right. They just stand there and tell us to change the amount of detergent or clean the machine with Clorox more often. I cleaned it 8 days in a row and the clothes still smell and still do not get cleaned. We talked to main man at Whirlpool and said they couldnt do anything because their 1 year warranty had run out. We have been using Whirlpool appliances for over 30 years but I will not ever buy another one. I have probably had 5 Whirlpool washers over the years but never had a problem until we got this Cabrio top loader without an agitator. I would not recommend this washer to my worst enemy, if I had one.

Purchased the Whirlpool Cabrio washer January 2010. Purchased the extended 2 year warranty from Lowes. After about a year I noticed around the bleach dispenser it was starting to rust. Over some time it worsened and grew bigger around all sides. I was unhappy about it, but thought it was just cosmetic and didnt pursue the issue. Now it must be on the inside and has started putting yellow spots on all of our clothes. It was only a towel or two at first and now it is on everything. I called Whirlpool and Lowes customer service center and they are just sorry and will not do anything. Lowes warranty does not cover any rust whatsoever although I cant find that stated on the warranty papers. I will never buy another Whirlpool product, ever. $600 for a washer and $70 for an extended plan to last on 3 years. I know people who have washers for 10 or 15 years. Im so disappointed.

The machine has an infinite water level setting, an agitator which I feel cleans clothes better, separate settings for water temperature for both wash and rinse cycles, and the ability to soak prior to washing by just leaving the lid up. You can add bleach and fabric softener to dispensers that will add to the tub at the time needed. My machine has been a really good one.

I bought a washer from Lowe’s Home Improvement in September 2017, called a couple weeks after the purchase. They sent someone to repair machine. It is still not working. Called Lowe’s back. Was given an 800 number. Talked with someone at this number got nowhere. Was given another 800 number. I am waiting to find out what is going to be done. This is terrible customer service.

Purchased washer Aug 2012 and has increasingly been leaving white residue after wash cycles. Have used the Extra Rinse function to no avail and use half the recommended amount of HE Tide. Now I have to run the Rinse, Drain, Spin function twice with darks to remove the residue. I have also been doing the monthly maintenance which has not helped at all. This machine seriously detracts from the Whirlpool name and if they are unwilling to fix the problem, it only publicly displays the companys integrity.

Have had this washer for one year. Clothes have never been clean since day one. Dark clothes come out with white marks all over. Having to use an extra rinse cycle or set on bulky items - whats the point of a high efficiency appliance? Still not clean after that anyways. Stains such as chocolate and toothpaste still remain after washing and my husband complains of finding small holes in his clothes. Lid needs to be left open at all times or you get a funky smell. I am using the HE liquid detergent, even tried a cold water product for cold washes. I hate this washer. Wish I had my 20 year old Kenmore still.

If 0 stars was an option, I would have chosen that. Ive had my own home for 34 years and have had many washing machines over the years. My Whirlpool Cabrio is absolutely the worst washer I have ever encountered. It doesnt get clothes clean and constantly gets out of balance. Whirlpool did a service call and said it is functioning as designed so I was unable to get a replacement. I really hate being wasteful and adding a huge appliance to a landfill but I will be replacing this machine as soon as it fits into my budget. I dont have a receipt to submit because it was purchased by my builder at my request. Do not buy this machine!

My NEW Whirlpool top loader just stopped working. I bought it in June 2015. The extended warranty I purchased ended at the end of June of this year. Guess what happened a few weeks later? The thing died. Seems totally fishy! My parents washing machine lasted 20 years. Why does this one die weeks after the warranty expired?

My complaint is basically the same as all the others. Clothes do not come clean in my brand new Whirlpool washer. Ive had two other Whirlpools, and they were fine. This one, however, is a piece of junk. One of the main problems is that the washer is designed to use only lukewarm water, even on the hot setting, it does not use hot water. Another problem is too little water. Another irritating factor is the constant locking of the lid. Another problem is the constant starting and stopping of the agitator. This cannot be good for the motor. Im at the point of giving away my new washer which Ive had for exactly one week. This is a totally inferior product, and I feel that I have been really ripped off.

Whirlpool cabrio mod. WTW7300XW1 - I purchased this washer Nov. 2013. It did not work right from the day of delivery. Our clothes come out dirtier than before washing. Machine smells awful. I spend more in machine cleaner than in laundry soap. I have always purchased Whirlpool. Very dissatisfied with this model.

I bought a pair front loading washer & Dryer May this year and took Delivery in June. First problem was with touch controls. I should have Known then it would be trouble, they replaced it then we went home to Fl. - Aug. Returned in Oct - used the machine eight times total and it locked up with our Clothes inside in water. Called for service, was told it would be a week before someone could come, then was told after four days it was the mother Board and it would take at least another week to get our clothes out. Their Service is the worst I ever have dealt with. The whole house - we Bought Whirlpool based on the Maytags we bought for our House in 2004. Never a problem but those Maytags were Maytag - not whirlpool. I would never buy any Whirlpool Appliances again. It is sad because I try to buy American made to support our fellow Brothers and sisters in the work Force but now I will buy made anywhere as long as it works and has reasonable service. Whirlpool is not the same as I Remember from years ago.

From day one I was not happy with the new auto fill washer, I was told I just needed to get used to it! Well I have tried every cycle available and no matter what I try cloths don’t come out clean, using the deepwash cycle Sheets on top were still dry once cycle was completed!! Give me back my old washer! Washed much much better.

This washer is an extremely poor choice if you wash clothes. It has so little water it does not dissolve HE detergent, Clorox 2, or OXI Clean. After even one wash it does not clean your laundry. If you choose to wash your sheets (even though there is a sheets and deep washer setting) its a joke. I could do better by washing things in the tub. I realize its a low usage water washer but you cannot even add more water unless you put it in with a bucket.

This is the loudest washing machine I have ever had. Sounds like it is grinding. Called Whirlpool and said that is normal. Will never buy another one and will let everyone I know how noisy it is and not buy one.

We have had this Whirlpool Duet WFW9150 washer for 7 years, doing 2-4 loads a week. Overall we are quite satisfied with it. A few complaints: We are on a well, and so get the odd bit of crud in the water. The machine has filters on the inlet lines, but you must pull it out from the wall to get at them. The filters are hard to remove. If something goes wrong--power blip, or sensor something, you have to restart the cycle. There is no way to continue from where you left off. There are features I wish it had: Rinse with warm or hot water, a spin only cycle, And Im in a hurry and it isnt very dirty cycle (Shortest cycle is almost 2 hours). Whirlpool doesnt have a service center for our area. If we need repair we need to take it into town. This is inconvenient.

We purchased a Whirlpool Cabrio washer in 2009. It makes awful sounds during the draining and spinning cycles, has started leaking in the past month and now, several error codes and will not finish a load of laundry. We have a family of eight and thought that we had bought a very dependable product for what we need. Boy, we were wrong!

The lid stopped locking just over one year after I purchased a Whirlpool Cabrio top load washer, which disabled the washer from washing. After investigating, it seems the electronic control board needs to be replaced, which will cost $400 just for the part. I have a large family, including a disabled child, and a washing machine is mandatory necessity that I cant afford to replace after only one year.

We purchased this washer in 2017, its the top loading Cabrio washer and it has been nothing but junk since day one. Purchased from RC Wiley in Boise and unfortunately did not buy the extended warranty because we trusted that this American company would make a washer that would last longer than 3 yrs. This washer barely washes clothes, leaves a residue on them since there is no agitator, also constantly gets unbalanced or gives and error of LF which means water supply issue when there isnt one. My 15 yr old about has a heart attack when he uses the quick setting and his clothes arent done in an hour and a half. Ive even resorted to turning the thing on to just rinse and spin so things get done sooner, still the stupid washer just sits. I would sell it but I dont want to pass on the pain, so its going to the dump to or to Goodwill cause its not worth the headache. Too bad you cant trust an American company to make a good product. Sad I really wanted to like this washer.

On October 29, 2009, we bought a new Whirlpool 30 gallon gas hot water heater to replace a Rheem we had for 20 years. We immediately had problems with the relief valve leaking, so we ran at the local hardware store and bought another valve. Next, we had trouble lighting it (husband was a plumber years ago) but a call to the hotline and we were in business. Now just over 3 years later, the pilot light started to cut off at will. Troubleshooting solved nothing. We called the hotline again and were given a part number, an authorization number and told to go back to Lowes for a replacement part. Figuring how our luck runs, I called first and was told there was no such part number. Trip saved. Now after reading all of these reviews, we have decided to cut our losses and buy another Rheem. You can find the Whirlpool hot water heater sitting beside our 2-year-old Kenmore HE washing machine (also made by Whirlpool) on the garbage pile. No more Whirlpool!

I purchased Duet washer 3 years ago, but it wasnt installed until a little over a year and a half ago. Machine started making loud noise during spin cycle, and eventually would not spin the water out of the machine. I contacted Whirlpool and was told there was a defect in that particular WP model and if it was confirmed by a provided tech, WP would provide the parts for the repair. The tech confirmed the problem, and I was told the repair would still cost over $450, even with the free parts. When I approached WP and asked them to fix the machine since it was a known defect, it was denied that there was a defect.

We purchased a Whirlpool Cabrio washer 6 years ago. This washer has been such a terrible appliance, I would not recommend that anyone buy one. The top of the washer has broken 2 times. Whirlpool will do nothing about it. It is a manufacturers defect where the glass pops out of the top and then breaks the frame it is in. We had it replaced last year and the new one is now broken - same problem. It also does not get clothes clean and the clothes get ruined because they become all entangled in one another. We will never purchase a Whirlpool appliance again. I did have a 5 year service contract on these appliances but once out of warranty - you are on your own.

I have the top load Whirlpool. Its very roomy for my covers, rugs & towels. It has a setting for me to just clean my washer or if I need to just rinse it. It has a cycle just for that. Or if I need a quick wash or a just cold water wash it has those cycle. When my cycles are done it makes a cute jingle sound to let me know its done.

I have a Whirlpool Duet front loader. Sick of it since I bought it! Not enough water to wash & rinse clothes. After consulting sites on internet, husband decided to try adjusting part. He just took off the 3 screws & lifted top off. On the outside part that has a white plastic housing, he turned the longer screw 2 1/4 times clockwise. EUREKA! We have more water! You may need to start out adjusting 1 turn & work up till you see a water level you like. Just dont let the water come over the wide rubber water guard.

I purchased a new Whirlpool Cabrio Platinum washing machine 2 years ago. Do not like it at all. Does not get my clothes clean. Pulls threads in my clothing. When I wash clothes on the normal cycle they are barely damp when the cycle is finished. When I use fabric softener it leaves blue spots on my clothes. I cannot afford to buy another washer so Im stuck with this one until it breaks. I would NOT buy another Whirlpool high-efficiency washing machine ever again.

I agree with all the unsatisfied customers with the Whirlpool Cabrio! Clothes do not come out clean! I called Whirlpool also and was told to be sure to place my clothes around the sides of the tub, which I always did. If Whirlpool was smart, they would take the complaints about the Cabrio and offer the customers a small amount of money towards purchasing another Whirlpool washer. I know I would have appreciated that. Instead Ill go out and buy another washer and not a Whirlpool. Even my kids dont want this washer and its practically new!

I purchased a Whirlpool washer (WTW4800Q) in November 2011. Already, it has rust in the tub. The warranty does not cover this. I never really liked the thing since I have had it. It takes much too long. Lid locks and then starts over. Also, warranty is not good. I wouldnt ever buy their product again and suggest no one else should either. I loved Maytag before Whirlpool bought them out. Im putting this one on Craigslist and buying a real washer, a Speed Queen! Yes, Speed Queen has all metal parts and makes a home washer. Just have to find a local dealer. They are there.

I do like washer to be efficient and quick at what they do.. I also like the way they are economical and use less water he energy economical it what I need.. I do like clean clothes. Right now I am using an ancient one and the sound drives me nuts..

About two months ago the washer starting stopping and the UL light continued to come on during every spin cycle. So I would adjust the clothes and start it again. So I decided that I should call a certified serviceman to come out and access the problem. Today a certified serviceman came out to access the problem. After about twenty minutes I was told the tub needed to be replaced and the cost and labor would be $600 or more. I do realize that the washer is about 8 years old but to completely need a repair like a new tub. I am very upset and have no idea what to do.

First off, took five weeks to get the damned thing delivered after buying it at Lowes Home Improvement. Have problems with the drain overflowing when the washer tries to empty. Major plumbing work to rectify that. My complaint with Whirlpool is the washer doesnt work. It will partially fill and then stops. The wash light then lights up and nothing happens. I let it sit for three hours and the clothes never washed. It took an act of God to get the washer to empty. It never did spin the clothes. The washer refuses to work through the cycles. $1500 wasted on this POS! Trying to get an appointment scheduled is equally frustrating on Whirlpools website. Never again will I buy Whirlpool!

Does everything its supposed to except get the clothes clean! Nothing gets clean, even on bulky setting when theres supposed to be more water in the machine!

Purchased this washer 7 months ago. We are a family of 5 with A LOT OF LAUNDRY!!! I adequately researched a machine that could do large loads of laundry, WELL. I read at least 100 reviews and went forth. (Note to self that anyone giving this machine a decent rating, is a DIRTY, SMELLY, FILTHY LINEN WEARING FOOL who doesnt take much pride in their clothing cleanliness.) I proceeded onward and after paying A LOT OF MONEY for this 4.8 Whirlpool Cabrio Washer, I found out within the first two days of owning it, that IT IS GARBAGE! Regardless of the 4.8 drum size, you can only fill it less than 1/4 of the way with clothes, to even hope they will be touched by water. My clothes come out DETERGENT STAINED & DRY! Insanity... A washer that doesnt wet the clothes!!! We have had 4 repairmen come out within this time, because I am fed up! I have been physically shown and told now, by all 4 guys, that the washer will not fill more than 9 inches with water. They advised me to fill Home Depot buckets and throw them into the drum. THIS IS WHAT I DO, TO SATISFY THAT I AM WETTING MY LAUNDRY - PURE CRAZINESS! The repairmen told me to set all loads to bulky sheets + extra rinse + highest soil. This is a 1 hour, 26 minute initial setting. Note that my adding water messes up the computer readings and it will reset throughout the washing cycle multiple times. Even with all of this... the machine still doesnt wet the clothes!! The top and center of the load is BONE DRY! This machine will not wash sheets, blankets or comforters, either. Dont waste your time trying!!! Dont be fooled by the drum size. Your great grandmothers 1930s 1.6 cu ft washer washed more clothes in any given load. #1 My water bill is through the roof. #2 The washer constantly resets and runs on any single load for over 2.5 hours AND #3 MY LAUNDRY PILES HIGHER AND HIGHER, as you cannot put more than a smattering of clothes in the machine, at any given time! GARBAGE, GARBAGE and MORE GARBAGE!!! I would be better served to find a stream and a flat rock and start doing my laundry colonial day style! I am done... Finally had enough of this insanity! RETURNED THE MACHINE THIS MORNING!!!

I have purchased a Whirlpool Washing Machine Mode W/P WM ROY 6212SD(31089) Sl.No.INF 153400517) GRAY/CHR TN 6.5 on 05.12.2015 with two years warranty on complete washing machine. The warranty period over on 04.12.2017. Exactly after over 3 months the machine start giving noise and we had been in touch Whirlpool and registered the complaint during last week of March 2018 and their local service center people visited, charged Rs.500/- service charge and informed that the machine to be taken to their service center to ascertain the complaint. After over a week informed that the machine complaints of Tub Support, Seal, Bearing, Drive etc. and the estimate is Rs.5,900/- including transportation (hardly 6 kms). The machine cost was only Rs.16,900/- then. I am surprised to know that just after 3 months of expiration of warranty the machine went wrong and the cost or repair costs me Rs.5,900/- is very huge. I hope the concerned will examine this.

I purchased this machine three years ago. It is junk. I have had two washing machines and they lasted for years and years. Never had a problem with either machine. I purchased them from Sears. When I the Cabrio, I was told it was the top of the line washer for Whirlpool. Three weeks ago it started making a noise like a plane taking off. It wouldnt spin the clothes. The repair person said that it could be three different things the parts, for which, would cost in the vicinity of $200. However, since it was making such a loud noise and water was coming out from underneath the washer, he was certain the transmission was out. He said the noise was an indicator the bearings were gone. I didnt see much point in repairing the washer if the transmission was out because it couldnt be fix.There was a couple at Lowes purchasing a machine at the same time as myself. They said they had a Cabrio also and it was only two years old. It wasnt spinning the clothes either and making a tremendously loud noise. They told us this before we mentioned that we had a Cabrio also. I will neither purchase another Whirlpool product. Junk!

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.

I purchased a Whirlpool front loader as well as an extended warranty. The machine worked well for about a year and a half until i noticed rust patches beginning to form on the front of the machine. We contacted the retailer that we purchased it from and they suggested that we call the people that we had bought the warranty from. Unfortunately, the warranty does not cover rust, so we have to wait for it to rust out and just buy another one. It is only 2 and a half years old and is totally rusted across the front of the machine! It is extremely unsightly. This is the second Whirlpool washer that we have bought and the second one to rust out on us. I would never buy another Whirlpool appliance, and extended warranties are not worth the paper they are written on, let alone the amount that you pay for them!

Whirlpool has a terrible customer service! I have an almost new washer broken and I had it repaired. The company is having the same issues in another model and yet, they would not offer to even refund the repair.

Purchased the matching set. Have had four years and need my second service on the machine for issues. It is a top loader and does a good job but the tub is very deep and not made for short people with a few delicate items cuz they are hard to retrieve. I have to use tongs to get them out.

We purchased this machine new less than 6 months ago. We found that it is not cleaning our jeans. We cant even work cattle and get our jeans clean. I called Sears and Whirlpool and told them it does not clean our jeans. They said it was under warranty and that they would come out to see if it was working properly. Well they said it was and then sent us a bill for $77. They said Customer Instruct was not covered under warranty. I already read the instructions and I knew how to operate this machine. The technician said this is not the first time he has had this type of complaint. Anyway I am VERY dissatisfied with this washing machine and I want Sears and Whirlpool to take it back and give me a better machine. I want one that can get clothes clean. If you are satisfied with dirty clothes then I guess you will like this machine.

ECO friendly top load Whirlpool washing machine - I bought this machine September 2013. Now it has a continuous clicking sound. It appears to be the lid locking mechanism and the washing machine will not turn on. It is under warranty and I am finding it hard to get a repair service in my area that is directed to Whirlpool to come and fix it. The only appliance repair in our area states that they will charge for trip and service if they find that is not a defect within the Whirlpool perimeters. I could be charged up to $200 for trip and service which is half of what I paid for. Whirlpool states this is not the case, and I am now having to wait a week to even set up yet another appointment. I have other machines that lasted 7-10 years until they wore out. I am frustrated and what could be a simple fix has turned into a financial nightmare.

I have the original (gak!) Whirlpool Calypso Washer and Senseon Dryer pair. They have given great service, and I find them easy to use. I wanted a top-loader but I didnt want an agitator. These fit the bill. How long have I had them? Gosh, must be 12+ years. A recent service call indicated that other folks havent had the same luck - apparently the knee-action is troublesome - and I found the Whirlpool-trained service techs werent very knowledgeable and was able to fix the thing myself with parts off eBay! All in all, I would definitely look at Whirlpool for my next pair.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

I bought A Washer Whirlpool and right after 30 day of the purchase my washer went bad and I called the Whirlpool Services and they told that will take about 30 days to come out and take a look at it. Are you crazy!!!! Freaking garbage that is what is. Never would want to buy Whirlpool again specially with that type of customer services they have..

The washing machine continued to display an F1 error code. I contacted the manufacturer and was told that they will not do anything about the problem due to it being out of warranty. This is the first time I have complained about a product or service and want to try and assist anyone who may be thinking of purchasing a washer from Whirlpool. I do not recommend purchase of these units.

I have the same lid closure issue expressed by many consumers and whirlpool refuses to acknowledge this as an issue, only recommends purchasing a new lid at $225. Lid design is flawed, metal L bracket connects to plastic housing/trim/side of lid, causing glass to pop out and stress cracks between screws. New models of same washer have redesigned lid, no cross reference part number or dimensions listed to determine if new lid will fit.

Whirpool has its main washers, then the off brand of Whirlpool. After using the washer after a few months the balance starts to get off balance. Trying to find parts and get them put in is easy, hard part is replacing them after they wear off after use a few months.

Very reliable and cleans clothes very well. I have used almost every machine on the market, and none compare. Very quiet and I use very little detergent and CLOTHES come out very clean every time. I am just very satisfied with my experience.

Purchased my Whirlpool Duet front load washer WFW9150WW00 new in 2010. Also purchased extended warranty. After four years, just before my extended warranty was up, the entire inside needed replacing (drums, bearings). Now at only five years old, it keeps making a beeping noise in middle of wash cycle and wont continue working. Serviceman was told by a Whirlpool tech. that it could be two things, one being the door jamb, the other being the control panel. Door jamb was fine. Ordered new control panel ($240), had it installed and yet the washing machine still keeps beeping and doing the same thing. The serviceman doesnt know what else it could be. So, I am forced to return the part and purchase a new washing machine. I would never recommend Whirlpool to anyone!

I bought Whirlpool top-loading high-efficiency low-water washer Sept 2018, model WTW5000DW, Serial # C83444466. Worst washing machine ever! No matter which water level you choose, it will not dispense enough water to cover the top of the clothes load, therefore the clothes are just moved from side to side with only the bottom layer of clothes getting wet; top clothes stay dry. Not enough water to fully agitate to clean the clothes!Whirlpool serviceman came today (Jan 13, 2020) to recalibrate the settings. VERY NICE MAN BUT THERE WAS NOTHING HE COULD DO TO SOLVE THE LOW WATER LEVEL. Recalibrating settings did nothing to solve the problem of not enough water. I am 81 years old and I have to manually add at least 4 buckets of water to an average load of clothes. This is unacceptable. Wont someone please initiate a class action lawsuit against Whirlpool for selling this very obvious poorly designed machine? NEVER EVER BUY A WHIRLPOOL WASHING MACHINE. It is a waste of money.

Whirlpool Cabrio washing machine WTW8800YC0 - My washing machine that I purchased a little over 3 years ago apparently is a piece of junk. Ive noticed a smell in the past few months, even while using Affresh. Now, its making so much noise that we must close the laundry room door while the washer is on. I called customer service and they will sell me a new 1-year warranty for about $345.00. Customer service thinks it sounds like the motor or the gear box! After reading the reviews on this washer, its not worth it to repair. More trouble looms for us. Whirlpool doesnt stand behind the product and as many complaints as there are, the washer shouldnt even be sold anymore! Never buy Whirlpool!

Back in the day GE appliances were made to last and last - the only one I have found close is Whirlpool. They have style, dependability and long lasting products. My washer machine has a ton of features and I didnt pay more for any of them.

I dont like the sensing feature that takes away my choice of water level control. I dont like the locking lid. It doesnt clean the heavily soiled clothes and I have to wash them twice because of the low water level. When the water is running in during the spin cycle, after the rinse cycle it washes away all the fabric softener. It takes longer from start to finish, so I dont see how it could be energy efficient. I dont like anything about the so-called energy efficient models. My opinion is they should not have changed from the old model. If it is not broken, dont try to fix it! I will never buy another Whirlpool product unless I see some significant improvements.

Whirlpool washer Model WGD4815EW1. Bought this washer just about 4 months ago and right away I hated it but was told by people that all the machines had gone to the lid lock and that the government had mandated the energy saving devices on the machines so the machine will only put just a little water in the machine. I have been VERY VERY unhappy with this machine. My husband figured out a way to bypass the lid lock mechanism. Then after washing clothes many times I found out in order to get my clothes clean I had to just set the dial to Bulky every time OR I had to wash the clothes 2 times to get clean if I didnt. Once we bypassed the lid lock and then I figured out where to put the knob so the clothes would come clean I was fine until last week the machine just would NOT wash or do anything... it filled with water and just sat there until my husband got the water out. I located a Speed Queen from an appliance store and I am much happier. It does not have the CRAZY lid lock on it. I realize that some children are apt to mess with the washers. But I dont have children anymore and when I did I had a laundry room with a lock up high on the door so they could not play in the laundry room. I dont understand why this so called mandate could not have been done in a way as to allow those with kids to have the option on the machine with a built in code device to set the machine so the lid will lock and those of us without children in the house to opt out of the code to set the lid lock. NO REASON why we cant have a CHOICE. As far as I see it is a way for the government to try control more where they need to keep out. The cars have been designed with safety locks for children to keep them safe, but it is up to you to choose to use them. Same principle! Now for the mechanism to make it so the machine will only put so much water in the machine to wash. Youre NOT SAVING any ENERGY or WATER if you have to wash the loads twice!! This whole mandated business with the newer washer machines is a huge JOKE on everyone. I will be searching out used machines and having them rebuilt because I dont EVER plan on buying another one of these newer machines. If enough people stop buying them the manufacturing companies can raise some cane with the government to get the mandate lifted. NO I will not buy another Whirlpool washer. I encourage some of you out there who LOVE a challenge to figure a way to change the stupid motherboards on the newer machines and create a great business for yourself because if someone else can create it you can recreate it.

We had a Whirlpool washing machine 650s, fully automatic on 28.07.2011 at M/s. Next Showroom Reference bill number 910, Sr no INF **. We had attended, 2 times, a problem with the digital board. After advice from your Whirlpool service person, we had fixed it cutout (make whirlpool), but now, its the same fault with the digital board. Kindly take further action regarding this same problem and sort this out immediately without any further reminder.

We purchased a Whirlpool Cabrio Washer (Mod #WTW7300XW1) and Dryer in 2011. Ever since we have had the washer it has eaten clothing, towels, sheets etc. It now has a main bearing that is so noisy that we have to close the door to the laundry room to be able to hear in the rest of the house. Also the sealed tank around the drum is now leaking. We invested close to $1000.00 in this washer and in my opinion it is a piece of junk. The washer repairman told me that he has had 3 (three) other Cabrios with the same problem in the last month, but Whirlpool says that there is nothing they can do as they have had no issues with this problem. Last Whirlpool product that I will buy.

We bought a Whirpool Cabrio, model WTW62000W9, and it is junk! We bought higher-end thinking that it would last. It is less than two years old and averages three loads per week. The transmission is out. It needs to be loaded on the boat back to China.

My washer is less than a year old and wont spin out all the water. Ive called out a repair person and they told me there was nothing wrong with the machine, and to read the manual!

This Whirlpool washing machine is incredibly annoying and slow in everything it does. First off when you press the START button it takes 2-3 minutes before it decides to do anything, like maybe add water (except click, click and more click). If you have pressed the start button and you want to stop it to add something... again you have to wait almost 2-3 minutes before the lock is released and you can open the door. I am at 2 hrs and 15 minutes as I write this on the LIGHT WASH cycle with extra rinse and its still going. I have never seen anything like it. Cant imagine how long a HEAVY CYCLE takes. Cannot even try to measure the time. I put the load in and go to work and hope its complete when Im done 8 hrs later.We had a Maytag for 15 years with no issues (other than a drain hose cracked and had to be replaced) and it was time for a new one with a move to a new place. The sales associate convinced us this was the best machine at the time... Well what a mistake that was. There are no complaints about the actual washing. Everything comes out clean but I suppose taking that long I cant imagine why it wouldnt. I certainly cant recommend a Whirlpool washer to a friend, because I dread the thought of doing laundry at this point.

It is a very reliable and efficient washing machine. I enjoy the energy saving features as well as how clean my laundry is, no matter how soiled they may be. I would definitely recommend a Whirlpool washing machine to a friend.

Bought this washer two years ago. First experience was when a load of towels became wrapped around the agitator. Called in service tech who told me to load the bin with the cloths pressed against the bin wall away from agitator, as if the cloths/towels would stay away from agitator. Two years later, Im ready to the machine to the street. Forget sheets and bedding. The agitator wraps them so tight that I almost rip the cloths/sheets to unravel. I had to wash a pair of work pants that were soiled with mud three times and there was still a stain. I will NEVER EVER buy another Whirlpool product.

I purchased this washer brand new just 2 years ago. It started making loud crackling noises approximately 3 mos ago. Yesterday it decided it did not want to spin or drain. Today a repairmen tells me its a wash. The computer screen has gone wacky and the cost to replace that will be well over $400, almost to the penny what I spent 2 years ago. This is not a good product Whirlpool and i trusted you since my previous washer lasted over 15 years. I need a refund and a new washer! Disgusted!

I purchased Whirlpool washer in Dec.2017 and used it in winter months only (Nov to March). It kept leaking and had to get appliance repair service for $50 and was told that machine is defective and whirlpool should repair it or replace it. I phoned whirlpool and they told me I have to use their appliance repair shop to evaluate the machine for cost of $130. The inlet valve was leaking and needed replacement for a cost of $253.55 and whirlpool shirked all and any responsibility. Dont buy whirlpool as it is not a good product and service is poor.