Twice purchased washers Cabrio and both after 5 to 6 years break down showing f1, f2, UL codes. Shame on this company. They refuse to give us a particular time to fix it and have the nerve to charge us for the visit without fixing it first.

WTW6340WW0 - When washing clothes, on the last spin it stops and gives an UL error message. I make sure all the clothes are level and restart at that point but still the UL error message appears and water starts leaking from the underneath of the machine. Weve reset the and unplug the machine but no difference. Please help on what else to do.

Does everything its supposed to except get the clothes clean! Nothing gets clean, even on bulky setting when theres supposed to be more water in the machine!

I purchased a front loading Whirlpool washing machine March 2017. I have need to have the drain pump replaced and the motherboard replaced. Each repair took 30 to 45 days to get parts and service. I would not recommend the washing machine.

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

I purchased this machine from Sears on 04/23/2016 and have had nothing but problems and issues with it. It is loud and makes different sounds every time I use it. It has overfilled and underfilled with water a few times, the machine shuts down while washing and I have had to restart the machine. Half the time the clothes come out covered in soap and I have to put them through another rinse cycle. My bedding always has to either go through a second rinse cycle due to being covered in soap or I have to rewash it because it is all packaged together in the fitted sheet and never got washed. During the spin cycle it sounds like it is getting ready launch into outer space and it vibrates excessively. On numerous occasions I have had to untie my clothes as they are tied in knots. There have been times that I had to put the clothes through another spin cycle because the clothes contained too much water. The final straw was last week (03/27/2019). I washed my sheets and they came out bundled up in the fitted sheet full of soap stains and I had to rewash them. When the sheets were done I put the comforter in the wash and started to clean the house. When I went into the laundry room the washer was not running but the wash light was on so I opened the lid and felt the comforter and found it to be dry. I closed the lid and pushed the start button. After a few seconds the washer shifted to rinse without even washing the comforter. When the washer stopped running and the ready light came on I removed the comforter, unplugged the machine, shut off the water, disconnected the water hoses, placed the machine on a dolly and took it to my scrap pile. I could not find any Whirlpool washers with any good reviews so I purchased a Speed Queen with a 5 year parts and labor warranty.

I have had this front loader for 5 or 6 years. My clothes absolutely stick, I cant stand the smell of them. I have used Affresh, the recommended cleaner 3 days in a row, multiple cycles, no improvement. I did the vinegar treatment, leave the door open etc. What is upsetting is I have read Whirlpool has been aware of the mold and mildew problems of front loaders yet continue to manufacture them. The gasket in the front enclosure pockets at least a cup of water and other gunk from the wash. A waste of money!!!

We purchased a Duet from Lowes just a few months ago. Within 2 weeks we had an inoperable machine. After 2 phone calls a service technician came out and looked it over. He had to come back a total of three times to replace the motherboard. That worked for about six weeks and it died again. He came out again and replaced the motherboard again. Fast forward two months and the machine is once again inoperable. When plugged in, it makes an ominous growling sound but nothing else happens. The idiot who designed this thing has no common sense. Its programmed so that it will LOCK on any failure. Not only has every one of these episodes left us with a load of clothes in there getting moldy, you cant even get to the model number or serial numbers; both of which are only visible inside the rim of the machine.So adding insult to injury, your machine is broken, your clothes are in there getting ruined, and YOU CANT EVEN GET TO THE INFORMATION YOU NEED TO SET UP THE SERVICE CALL. If it had only happened once, Id laugh, but this is the third time and its not funny. We bought this machine because it said proudly made in USA. Next time, Ill support the Korean economy and buy a reliable, durable Samsung. The only positive I can offer is that the Whirlpool live chat person was able to set up the service call for me even though I cant get to the relevant data inside the machine. DONT BUY A WHIRLPOOL WASHER. Despite their legacy and US-feel-good associations, the sad truth is that they are poorly engineered and poorly manufactured.

We purchased this washer in 2017, its the top loading Cabrio washer and it has been nothing but junk since day one. Purchased from RC Wiley in Boise and unfortunately did not buy the extended warranty because we trusted that this American company would make a washer that would last longer than 3 yrs. This washer barely washes clothes, leaves a residue on them since there is no agitator, also constantly gets unbalanced or gives and error of LF which means water supply issue when there isnt one. My 15 yr old about has a heart attack when he uses the quick setting and his clothes arent done in an hour and a half. Ive even resorted to turning the thing on to just rinse and spin so things get done sooner, still the stupid washer just sits. I would sell it but I dont want to pass on the pain, so its going to the dump to or to Goodwill cause its not worth the headache. Too bad you cant trust an American company to make a good product. Sad I really wanted to like this washer.

Purchased this beautiful sleek Cabrio washer in May 2012 from Appliance Smart, with its modern looking glass top, it looked so nice. The washer itself works ok for now, but it does unbalance a lot, thats not main issue. We deal with that. The poor design of holding that sleek glass top in is the problem. After a little over two years, it started cracking at the hinge that is just mounted in Plastic which holds the whole lid down, including the heavy glass. The glass started raising up, causing steam to escape. The lid is rubbing and very difficult to open. Appliance Smart is gone now.. We called the service repair person about 6 months ago, he looked at it, said its a problem that is not covered on our warranty and it would be approx $350.00 to repair!! So today, tomorrow or next week it will stop working because the lid is popping off! Its a terrible design, dont be fooled by its sleek look. The manufacturer takes no responsibility for this major design flaw. Beware, the very thing you need to be fixed wont be covered under warranty, lemon law, or just good customer service. We have owned several Whirlpool appliances and doubt that we will own one again, due to the way this issue was handled by Whirlpool.

Whirl Pool Duet Wash WFW9400SW - I had this washer for 5-1/2 years. I use it about 3 times a month. Warranty ran out this last February. Machine stopped working. Called tech and he came and said I need a new console and power board. Two weeks later I get told they dont make it anymore and sorry about your luck. I used this washer under 200 times in 5 and half years. Whirlpool offered nothing and I will never buy a Whirlpool product again.

I have had Whirlpool appliances for a very long time. However, I am extremely dissatisfied with the purchase of my last Whirlpool washer a couple of years ago. The washer is extremely noisy, to begin with, and I complained to hhgregg about this. They delivered a couple of other machines, all of which were very noisy. The latest problem with this machine has been with the tearing my clothes. My clothing gets caught under the agitator and the items tear. This is a poorly designed washer and I wish I had never purchased it. I was thinking and wrongly so, that the washer would be as good as my previous washers. Well, I was so very wrong.I wish to know what you are going to do for me with this problem which is so very annoying and costly.Marjorie **

1.0 out of 5. This is the absolute worst washer that I have ever owned. Do NOT fall for the top loader hype. The clothes do not get clean. Anything black constantly comes out with a white residue and whites are dingy. Ive tried numerous detergents and used as little as a tablespoon and still get the same results. The company just insists that its too much detergent or that I need to run the clean cycle after every 4-5 loads. The service guy that came out said this is the number 1 complaint with these washers and Ive talked to plenty of friends that experience the same issue. The company would have you think this is the first time they have heard of it.I have spent hours on the phone with whirlpool and Home Depot over the past year and neither accept responsibility or offer any solution other than some free cleaning tablets from Whirlpool and Home Depot offered $200 off the purchase of another washer. This was when the washer was only 6 months old. The only way around this is to rewash the clothes and a second cycle and to wash all loads on bulk load with an extra rinse. Yep. Great water savings there! Save yourself the headache and dont buy a top loader of any brand and I would never buy another appliance of any kind from Whirlpool and Home Depot because of their poor customer service in handling this common issue.

I HATE this washer!!! Did I say hate this washer? YES. Do not buy it. Delicate cycle. Ha ha ha. NO!!! Good thing Im retired because I need to check it every 5 min to see if its getting clothes wet or untangle a mess. I find I use the rinse and spin cycle once with a little soap and run it again to rinse. A lot of extra work. Sheets washed in the deep water cycle turn into a giant twisted mess if you dont stop machine and untangle everything. Hate it. Hate it. Do not buy this machine. I use more water by washing things twice or fewer items. What a waste of time!!! Locking lids are the worst thing ever designed. Why?? Dont tell me some stupid kid is going to climb in it. We should have a choice or be able to disable it!!! Worst machine ever designed???

I purchased the Cabrio washer about 2 years ago. This summer, I began to hear a roar in my washer when it was spinning. I called a repairman and in order to fix it, the tub has to be replaced and it will cost $258 plus service call. My sister purchased her Cabrio 3 years ago and her washer has the same problem. This sounds like a recall issue to me. I think Whirlpool needs to recall this washer or pay my bill.

My wife and I purchased this Cabrio washer 6 years ago when we got our new home. I have replaced the discharge pump 2 times, and approximately 2 months ago, we developed a noise so loud it was like a jet engine landing. I called our appliance store and paid $100 for an estimate, only to find out it will cost $973.00 to fix it. When we bought this, I was told it will be the last washer we will ever need. Ill never use Whirlpool again and recommend no one else does, either. I wrote to your customer chat line and basically the reply was Sorry about your luck. I know Im not the only one with this issue.

I purchased the Whirlpool Cabrio about five years ago. Last year, the motherboard had to be replaced. This year, it started load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $100 to have someone look at it, and was going to cost almost $400 to repair, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. Do I have Stupid tattooed on my forehead? I will never buy a Whirlpool again!!!

Purchased an expensive, Cabriolet Washer in 2014 to replace a well used Kenmore washer. Sucked into the, Whirlpool is a good brand and spent more than I would have. Lid lock fault started about 3 months ago, googled fix and found this to be a very common problem with this brand. Have been able to override and reset it but it is very frustrating to deal with. Called in a repair person this morning who, for $140 told us we had a faulty lid lock and for $360 he would replace it. I contacted Whirlpool and asked if they were aware of this very common complaint (just google it) and they were not but offered to make a record of mine. Please do not buy Whirlpool. Very disappointed with their product and their response.

I bought a whirlpool washer because we thought it was the best. It does not clean our clothes especially my husbands jeans. They are on their third wash at this minute. I use Gain HE detergent. I bought clorox 2, I use spray & wash & I have even started using a little clorox but the red dirt still doesnt come out. I never had this problem with my old washer. If there is any help for me here please let me know. If this is supposed to be a water saver I dont see how I have saved any after washing jeans for the third time. If they are not clean this time, I guess he will wear them dirty.

We bought our Whirlpool washer (WTW5700XWO) in April 2011. This machine has so many issues. Lets start with it not getting our clothes clean. Some clothes never even get wet. Then on the other hand, there are times when the clothes come out soaking wet, like it never went through the spin cycle. (We know it did because its super loud!) Recently, it started shutting off during the wash cycle. Sometimes, it doesnt release the soap or the fabric softener. I am so frustrated with this machine. There should be a recall. We paid $700 and now well need to go and shell out more of our hard earned money to buy something that actually works. I will never buy another Whirlpool appliance.

I purchased a new Whirlpool Cabrio washing machine from DeWaard & Bode at Bellingham, WA in January of 2007. The serial number is **** and the model number is ****. Several months ago, the dreaded F1 code appeared. The code initiates when the washing machine is started and must be cancelled and started 3 times to continue washing. Later, with approximately 19 minutes left in the cycle, the code reappears and requires canceling and restarting another 3 times, at times 4. I have no extended warranty so I have no coverage for repairs. I also dont want to pay for a service call for what is most likely the computer module as evidenced from the majority of complaints online. This washing machine still looks new and works other than the inconvenience of having to stand by when starting the cycle to reset the code and then having to run upstairs later to reset the machine when its partially through the cycle. At some point, it will likely quit operating all together. I have purchased several appliances over the years from DeWaard & Bode and will be replacing all kitchen appliances again next year due to a planned remodeling but at this time, I do not intend to get them locally due to this issue. I have reviewed several comments online and feel that Whirlpool has a real problem with this particular machine that they refuse to be responsible of. I was offered an extended service plan for 1 year at $132.01 or 3 years for $336.61 but Id have to wait to be allowed to utilize it due to existing circumstances. Im not sure if a fix is actually available. The local dealer did not offer any assistance.

The duet washer is just over one year old and started showing F25 code on screen. It had been making a really loud noise in the spin cycle. Last week, a really loud noise and then the loads wouldnt be spun. There was a puddle of water on the floor near the machine. We had a repairman out today and he stated that theyre repairing these machines all the time. He stated it was the bearing and that theyd been told that Whirlpool had installed bad bearing from a different supplier. I called the Whirlpool experience and after 4 minutes and 19 seconds, I actually spoke with a service rep. She said since my machine is less than one month over the one year warranty, Id have to call the extended warranty people. I asked for a supervisor and after 2 minutes and 38 seconds, she came in line and wouldnt budge from her story. They also stated that there are no service issues with this model washer. Extremely poor attitude and Whirlpool is doing everyone, whoever purchased a duet washer, a terrible job on these washers. At least, Ive now found out that there are a lot of other folks out there with the same problem. We need to get some attorneys to start a class action just like the mold/smell customers did already. Sad, sad day for Whirlpool as Id been a customer all my life.

Whirpool WFW9550WW-00 Front Load Washer - Washer was purchased 08/09/12. No problems until 07/12/15 when washer stopped working mid-cycle. Motor control board needs to be replaced, actuator needs to be replaced. $500+ Our local appliance store suggested we call the Whirlpool customer relations number and ask for the parts to be sent free of charge. We would pay labor. They gave us the model number, serial number, the diagnostic info. Long story short, customer service told me she didnt know why I was told to contact them. They can not predict the life of a machine. Less than 3 years for this machine. 22 years for my old Kenmore. Our old Kenmore never had a problem, but we thought that we should replace it in 2012 in case something happened with old machine. WISH WE KEPT THE 22 YEAR OLD KENMORE.

Dryer panel broke washer. The smell is so gross I will need to throw it out. I used only HE detergent.

We have had the washing machine about four months. When washing sheets, they twist up badly. The machine does not seem to get the clothes very clean. It seems that it does better when we put it on the bulky setting for all washing that we do. More water is needed I guess.

Do NOT buy this washing machine. It looks nice but that is all. My elderly parents bought this washing machine based on the past experiences with Whirlpool but the quality of the product has changed. This machine constantly errors and does not allow them to wash clothes. I have followed the instructions in the manual to try and clear the errors. I ended up calling Whirlpool and the response I got was... It will be anywhere from $80 to $125 for someone to come out and look at it. This is a product which should not stop working after 2 years. I guess Whirlpool only stands by their products for a year because they think it is only built for a years worth of service. I wish I had better things to say because the previous Whirlpool machine lasted over 20 years.

Bought this washer in 2013 for close to $800. About a year and half old it got real loud sounds like a freight train. Asked whirlpool repairman about it, and was told it is a main bearing going out. He said it would cost over $500 to fix it. Whirlpool warranty sucks - only one year. Called whirlpool, told them the problem and asked if this is a problem with this washer. Got told no they have no problems with it. Found out later not only do they have this problem with it they change design because of it. Repairman said his own daughter had same problem and he had many service calls on this model all with same problem. WHIRLPOOL WILL NOT REPAIR OR REPLACE PRODUCT WHICH IS A MANUFACTURE DEFAULT. It sets in our house unusable. I will never buy a whirlpool product again. Sad because that use to be all I would buy.

Uses little soap. Not sure on clean. Don’t think front loader clean as well as top loaders. Would recommend top loaders with no agitation. Also would recommend white as a standard color. I am unhappy with the way a front loader works. I am happier with a top loader, cleans better.

I purchased the washer 1.5 years ago. At about 9 months, the latch was in need of replacing. The washer was locked and would not unlock. That was fixed. Fast forward to 1.5 years old and the control board needs replacing. The washer stopped in the midst of a cycle, filled with water. The repairs are over $400 -- nearly the price of a new washer. Ive never had a washer to go out on me. I willingly gave away my previous washer for the purchase of a newer model and did not expect this fiasco. I will recommend against purchasing a Whirlpool washer.

The smell from the washer has gotten so bad we have to keep the door closed to our laundry room, or the smell will permeate the whole front part of the house, as it is we have to keep the door to garage which is adjacent to laundry room open to air out laundry room. Our friends and guests, are aways telling us we have water leak or something mildewing, or rotting in our house. The washer works well, and I cant find any buildup. We frequently run it through clean washer cycle, it smells OK for a hour or two, and odor returns!

I purchased washer (Whirlpool Cabrio wtw5600xwg) on April Fools Day 2011. The first repair was check on 1-27-12. I complained the machine was too loud and clothes seemed too wet - the call was under warranty but tech was unable to verify complaint. So guess what? On Jan. 21, 2013, machine sounds like a stressed jet engine. Now we are diagnosed with a bad gear case for a total repair of $439. Now we are not under warranty and Whirlpool takes no responsibility. Doesnt the consumer have any rights? Do you think Ill buy Whirlpool again?

When I purchased my Whirlpool Cabrio washer and dry, I was told by the sales associate that this was the top of the line. I paid a higher price for what I thought was quality only to find out that this washing machine (WTW6600SW2) Serial number CU2973872 is in fact poor quality, made of components that are cheap, unreliable and made to last only as long as the initial warranty. Prior to buying Whirlpool, I owned Kenmore and had a washer and dry that raised four kids, now I own a Top of the line Cabrio that cant wash the clothes of two adults. I think it is funny that two days after the washer started sounding like a jet plane taking off during the spin cycle, I received your sign up for an extended warranty letter. Then I take the washer apart to locate the trouble and find it is a single bearing on the top of the drive shaft, but can I buy the bearing and replace it? No, I have to buy the entire outer tub and drive shaft. So a $10.00 bearing will now cost me $200.00. I am sure that helps your profit margins considering all you have to do is a search for Cabrio problems to find 350,000 hits, or to ask a professional technician and receive the reply that they are replacing 2-3 of these tub and drive shafts per week. I would recommend that Whirlpool tell its shareholders that you have compromised customer satisfaction to line their pockets with profits. If that was your intent then you have succeeded, however you need to also tell them to sell their shares now as you will have no return customers. Most corporations have core values that deal with safety first and then always followed by quality. I can say with confidence that your quality can be nowhere near the top five with this many problems with your top of the line product.

Bearing on washer drum began getting louder at two years. Service man stated that Tide and a few other detergents were destroying the washer bearing seal. He told us that neither Tide nor Whirlpool will admit the problem exists. The cost of repairing the washer is close to the purchase price. Whirlpool should be subject to a class action lawsuit!

I call in to Customer Service to get someone to fix my washing machine because it wasnt working and when I called, I forgot to have my washing machine serial number at hand. The person on the other side told me that she cant wait for me to get the serial number more than 2 minutes and I ask myself, if they cant wait for me more than 2 minutes to get my serial number, then why should I wait a week to have someone fix my washing machine?

I purchased a Whirlpool CABRIO H2Low top load washing machine approximately 12-15 months ago from Lowes in Columbus, GA. I have been very dissatisfied with it from the beginning. I contacted Lowes and discussed the machine and expressed my complaints. I realize that it has a sensor and fills the machine with the amount of water according to the weight of the clothes but have found that regardless of what cycle I place the machine in, it doesnt place over 2 inches of water in the machine. It does not clean the linens, under garments or any type clothes. In fact, it has ruined my designer clothes. It is impossible to get the wrinkles out with an iron. Im very disappointed in the service we have received with this washer.

I bought this Cabrio Washing Machine just over a year ago and it never drained water when I was doing towels and bed sheets. Life got in the way, and I managed to run smaller loads in the regular settings. Now, the machine is just over a year old and it will not spin unless I put it on the rinse and spin issue. It takes well over 2 hours to wash a load of laundry. From looking at other reviews, this is a big problem. I would not recommend this washer to anyone. It cost a ton of money and was the worst washing machine I have ever used.

Whirlpool Cabrio washer - Its been a month now and still the washer is not fixed. The repairman through Lowes warranty service is the worst by far I have ever dealt with. I had new transmission put on, still wont agitate and smells hot. The washer is only 18 months old, well taken care of. This expensive hunk of junk is worthless and the aggravation for all this mess is worse. I called Whirlpool 2 times. The first time, I got a call with the standard oh so sorry bit. Oh boy, that gets the washer fixed. Not. I blasted them and Lowes again. I have had it with this mess. The repairman is supposed to contact Lowes a week ago for replacement. He has done zero. I called Lowes to check. How can they sell this junk to customers who pay for this washer? They know it is junk, Lowes and Whirlpool, so do the right thing and recall the junker for refunds to consumers.

Whirlpool Cabrio washer - Do not buy this washer. I have never placed a comment on the web before, but after reading about the same problems over and over, there should be a class action suit. The spin cycle will not balance. You have to stand over the washer and readjust the laundry. I called Whirlpool and I was told to unplug unit for 5 mins. This is a $800 washer that lasted about 2 years.

Clothes come out of washer are soaking wet. Despite multiple repairs within the warranty period (1 year), the problem was not fixed. Each time a separate part was replaced. I would consider this as a manufacturer defective product. Despite multiple complaints to Whirlpool customer service, they would not replace the unit. Problem continues and now the warranty period is over and I am paying for fixing the same problem. I would not buy a WP washer again.

Whirlpool Cabrio Model WTW6500WW1 - Have had good luck with previous Whirlpool Washers so thought I would purchase this one 2 years ago from Menards. Paid more than I normally would and thought it would be worth the extra money. Not so.......As many others, it has a foul odor that will not go away and now sounds like a freight train in the house. Called Whirlpool about this issue and parts are not covered. Total cost of parts including the tool that is needed for this repair is $187.00 not including shipping. Whirlpool has lost my business moving forward as like many others, Im sure. Very disappointed!

This is the worst washer Ive ever owned. It consistently gets off balance, doesnt clean the clothes, and is a perfect example of poor design. I have owned the washer for approximately 9 months, and hate it. Im getting rid of it as soon as possible.

Whirlpool cabrio top loader is junk from the first month. My washer has had way too many repairs. A&E repair has been a frequent at my home. Now Im getting ready to repair it again! Hub gasket or pump not sure this time. All has been replaced previously. Never ending - always something wrong with it!!!

Whirlpool Calibri washing machine - I have the washer for 4 years and have replaced four computer boards to the tune of nearly $300 each. When Whirlpool was told of my experience, they said they were sorry. Obviously, I am too and will not buy again. You would think they would give me one board at no cost, but I guess words are cheap.

We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.

Whirlpool washer WTW7800 Cabrio - I bought this machine in Oct 2010 for $900.00. This October, the lid started not closing. Next thing I know, the glass is popping out. After waiting on hold for 20 minutes, I was told there is nothing they could do but refer me to a repairman at a cost of $179. The glass is popping out. This is a defect not caused by washing clothes but poor workmanship. I am on hold again. I am calling channel 3 news to do a story and will not stop until it is fixed.

I have had this washer for a little over one year, it now does not work! I had a service tech out to look at it.. The motor gets too hot and the switchboard stops working. I have called Whirlpool twice and the options they have given me are not good! Basically it would be about half the price of a new washer! I should not be having these problems with a washer this new! I am very disappointed with Whirlpool and wont purchase this brand again!

Whirlpool Cabrio Washer Model WTW6400SW2 Serial CU0272414: I replaced my wonderful 25+ year old Kenmore washer with the Cabrio, 4 years ago. Within the first year I had to have a computer board replaced that was covered under the warranty. This last 6 months I replaced the suspension rods, was constantly showing that the load was unbalanced. Also have a LD error, long drain, probably because a sensor is bad. Today, restarted a load several times and could never complete the entire cycle. I resorted to unplugging, and starting a drain spin cycle and the washer just flooded my house. So Im done with this unit. Waiting for a class action suit. Lets get started. What type of unit should I buy now. I guess Im going to subscribe to Consumer Report before I buy another. Laundromat for me in the meantime.

I dont know who is the bigger idiot. The designer of this washer or me for not reading the countless bad reviews. I bought a Whirlpool 4.3 CU FT TL WTW5000DW machine on 7/19/2015. It does not come close to cleaning clothes. It now takes me three times longer to do laundry because I have to check every piece of clothing for any stains. These are minor stains mind you but, they will not come out unless I use something like Spray and Wash. My time is valuable, maybe I should drag my clothes to the river and beat them on a rock. Very disappointed.

The cabrio washer that we purchased in 2010 did a good job of cleaning the clothes but the case started rusting within 6 months. After service calls and e-mails and phone calls, there have been no helpful suggestions beyond buy a complete new case. I hesitate to do that because I am convinced there is a design flaw in the area where the soap dispenser is located which allows the soap to flow between the case and the drum and it eats away theinside of the case through the inadequate paint covering on the outside of the case. It is a mess. Now the instruction panel is bubbling and lifting. I carefully care for my equipment and have kept two washers over 15 years and they still were in good shape with cases still looking new. This is not something I am doing wrong. It is a piece of junk with a terrible paint job and it cost more than any washer I have ever had. I wish I had some recourse. I am on a fixed income and had hoped this would be the last washer I would have to buy. I have photos.

After reading all reviews online on the lid of the Whirlpool Cabrio Washer, it upsets me that there has not been a recall on this. Our lid has snapped & has to be held down until the lock light comes on. Often times during the cycle it must sense the lid is broken & thinks it is not locked & sets the load off line. I have to pause the load & then reset the load & hold the lid down tight until it restarts.

This is our second Cabrio w10550273a. The first one was just as bad as this one. It was replaced under an extended warranty we bought. This washer just like the last one constantly gives a UL code. Thought the washer and load are level.

If you are in the market for a new washing machine, steer clear of the Whirlpool Cabrio (or any Whirlpool for that matter). We have had issues with ours from the beginning. We had Whirlpool techs come out and were continually unable to fix the issues. Eventually they told them that it was not broken, even though one tech told us it definitely was. After four service calls they just stopped sending out techs and told us too bad. Now after less than two years it is leaking from the bottom. Yeah, Whirlpool, theres no problem with it. Save yourself the potential headache and get something else. Anything else.

We purchased a Whirlpool Cabrio Washer (Mod #WTW7300XW1) and Dryer in 2011. Ever since we have had the washer it has eaten clothing, towels, sheets etc. It now has a main bearing that is so noisy that we have to close the door to the laundry room to be able to hear in the rest of the house. Also the sealed tank around the drum is now leaking. We invested close to $1000.00 in this washer and in my opinion it is a piece of junk. The washer repairman told me that he has had 3 (three) other Cabrios with the same problem in the last month, but Whirlpool says that there is nothing they can do as they have had no issues with this problem. Last Whirlpool product that I will buy.

Have had this washer for one year. Clothes have never been clean since day one. Dark clothes come out with white marks all over. Having to use an extra rinse cycle or set on bulky items - whats the point of a high efficiency appliance? Still not clean after that anyways. Stains such as chocolate and toothpaste still remain after washing and my husband complains of finding small holes in his clothes. Lid needs to be left open at all times or you get a funky smell. I am using the HE liquid detergent, even tried a cold water product for cold washes. I hate this washer. Wish I had my 20 year old Kenmore still.

Whirlpool cabrio wtw7800xwo - During the 12th month of the use of this washer, the lid broke. I called Whirlpool to schedule a repair on it. I got someone here to repair it, and it was 7 days over the 1 year warranty. I don’t think this is fair when they sent the repair guy out too late when I scheduled this right before the 1 year was up. I came about looking this up online, and I find I’m not the only one with a 1 year lid. My next washer will be a 1980s built to last. This was the worst $1,100 I ever spent. I had to choose 1 star. Wish it had a choice of - ★★★★★.

I purchase this machine over 15 years ago. It’s still working, washes the clothes. The only problem the section where the bleach is poured is completely rusted out. The machine has definitely lasted beyond the 15-year cycle. I intend to purchase a new one. I probably would buy the same brand.

I wish I could give negative stars! My Cabrio Model #WTW6600SG2 sounds like a jet airplane on the spin cycle (this started 2 months ago). Now, Im getting the UL error, its not an an uneven load!

We purchased this Whirlpool Cabrio washing machine from Sears about four, maybe five years ago and have complained repeatedly. We have had repairmen out numerous times. Of course, they have had to order parts. My clothes are not getting clean and they now have an odor to them. The machine is getting noisier and noisier and it is rocking like crazy (I had to put plyboard underneath to protect the floor) during the rinse cycle. The water sprays out erratically and sprays even slower for cold water, then warm water, which was weird! Thankfully, I still have it under warranty (I got the extended warranty). I am now getting ready to call them again. I will never buy this brand again.

Washer is very mobile. Dryer does not dry. Refrigerator temp is never correct. After reading complaints, I firmly believe you know what the consequences of your products. I would never recommend Whirlpool again. I have used Whirlpool products since 1970 and always had good appliances. Your new products are worthless and you are spending more money on legal protection and lobbying than making a worthy product that actually cleans clothes and cools food. You are charging thousands of dollars for a worthless product and paying thousands of dollars for legal protection with warranties written to excuse your worthless product. Put your money on improving your products.

I just love the durability of my machine and the features that it offers. It does a great job washing my clothes and I feel like its a solid appliance that lasts for many years and its good quality for the price.

The machine has an infinite water level setting, an agitator which I feel cleans clothes better, separate settings for water temperature for both wash and rinse cycles, and the ability to soak prior to washing by just leaving the lid up. You can add bleach and fabric softener to dispensers that will add to the tub at the time needed. My machine has been a really good one.

What happened to the Whirlpool Corporation that we grew up with? I purchased a Cabrio Washer on 8-29-11. Here it is, 4-24-13 and the transmission is shot. Two loads of clothes were ruined and sensors went bad. All in all, over $500 to repair it. I called the customer service line, what a joke - bad product and worse customer service. Not even and Im sorry. Well it is out from under warranty and when I buy something, I research it first, she said. Wow! Thanks Reena for all your care and concern. I dont know if Ill ever buy Whirlpool again.

Our Whirlpool Dishwasher model WDT710PAYW is less than 2 years old and is rusting on the outside of the door where the steam vent is. Apparently the hole that was made in the door for the vent was not sealed, now the paint is blistering up due to the rust. Will not purchase another Whirlpool.

We wanted the ease of use and longevity of a top loader WITHOUT a full touch screen. Whirlpool has such units in a choice of price levels to accommodate most everybody. The agitator free design and automatic water level feature is amazing. Clothes are nice and clean and uses about the same amount of water as flushing a toilet.

I have had my Cabrio for a year now and quite frankly, I find more satisfaction taking all of my laundry to a local laundromat. There is no soak cycle and when you have a kid in sports, that doesnt help. There is no agitator, and I am now convinced that they were originally in all washers for a reason. My clothes have all worn out and are shredding, not to mention my very expensive bath towels that I am now cutting into rags. This was the worst purchase I have ever made in my life and will never even look at a Whirlpool again. When I bought my house, I had a Maytag that was 35 years old and it did a better job than the new Cabrio. Should have stuck with that brand!

Two-year old Whirlpool Cabrio top load washer; absolute piece of junk! Bearing on the drum howls like a train. Now the master board or some other sensor (under drum) is out. Serviced for the third time and the service repairman states its cheaper to replace than to repair. For a 2 person household, it is reasonable for us to expect more than 2 years from a washing machine. Same experience with Whirlpool 15 years ago. 1st time shame on you; second time shame on me.

I had my washing machine for about 10 days before it stopped working. I did about 4 loads of laundry. We have had 3 repair people come check it out, all referred by Whirlpool. They each had a different theory on why it wasnt working properly. Im now waiting for parts to be delivered and then service to be scheduled. When I contacted customer service, I was told (after waiting on hold for about 1 hour) that it was customer misuse. Ahem, first I heard that, and I think I know how to use a washing machine. I asked to speak with a supervisor. More waiting. Tina (#**) told me she will contact the service company about the parts. I told her to please conference me in on the call because I want to hear the outcome (and I dont want to wait another 1+ hour to reach customer service again). She put me on hold and then disconnected me! Really, all this time and 3 service people... Would be cheaper to just replace the machine altogether. What a headache!

In the first year of my Whirlpool Washing Machine, the motor quit working entirely. Fortunately, the machine was under a 1-year warranty and the motor was replaced by a Whirlpool service technician. My big complaint with this washing machine is this: Even though you select hot water for the wash cycle, the machine has sensors in it that only allow the water to get lukewarm. If it senses the water getting too hot, it adds cold water to bring the wash temperature back down to 78 degrees F. Next time I will do my research and buy a machine that actually allows one to use hot water.

I cant believe the list of people here with poor quality of their washing Machine. My first problem was covered under warranty. I have paid for two service visits from A&E and now every 5 minutes get the LF error. My fabric softener does not drain into load either. My only option is repair again and I got a sorry from Whirlpool. I think Im going to look for an old fashion cheap machine as it cant be of worse quality than this Cabrio wtw6400sw1.

My old 25 yr old Whirlpool died and was shopping for a new one. I saw the Cabrio and was really impressed by the features and large capacity interior. I can say that I thought my clothes were getting clean until I looked closely. I have never been so disappointed with this washer. I wish I had my old one back! Clothes arent clean, they are so twisted when I take them out and theres a horrible smell, like oil burning when it runs. The machine would fill up and when it would start to wash, it wouldnt, it would stop. And a loud humming noise was coming from the back.I shut it off and turned it back on and it wouldnt clear. I had to unplug it and plug it back in to clear it and start over. The bearings are gone now and I was going to have a repairman come and look at it, but now I wont bother! After reading everyones comments this Cabrio is a piece of junk and Im sorry I ever bought it! So now Ill be shopping for a new one tomorrow with an agitator!!! Im not impressed with the HE appliances!!! Ive owned this POS for not quite 6 yrs. Expensive to purchase and I will not recommend Whirlpool to anyone! Its sad that companies today make cheap products!! Built to last... ha!! Well never see those again!!

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

This is one of the best washers I have had 4 years now. The spin cycle is great. Feel almost dry when done. My daughter was going to order this set but cant get them anymore. I guess it is because it is too good of a washer.

I purchased my whirlpool washer on 01/24/2011 and I purchased a 5 yr extended warranty at the time of purchase. My washer broke down. I called the whirlpool co. After 5 mins getting through the phone prompts and another 30 mins on hold I finally spoke with a rep name Ashley who state that there was no account or record of my warranty. She connected me to another department where I spoke with Eva. I was advised that since the company that sold me the warranty was out of business whirlpool would set up an account for me if I faxed the information documenting my original purchase. I faxed the information, waited three days without a response. I called today went through the phone prompts and could not reach the reps I spoke with before. The reps today were not helpful and refused to even try to get me to the reps I spoke with before. I was advised that the previous reps provided inaccurate information.If an appliance comes with a one year warranty and a consumer purchases a 5 yr extended warranty should it be added to the 1 yr or is the first year included in the 5yrs? Wouldnt it only be a 4 yr extended warranty if that were the case? I am very disappointed in the lack of quality of my washer and misrepresentation that was communicated by whirlpool reps. At the very least they should answer the phone promptly and honor the commitment to repair products. This is the case number (**) I was provided the first time I called, but it is not recognized by the reps I spoke with the 2nd time. I was provided 866.368.6478 as a contact# and a fax#. I faxed my receipts to that number as instructed.

I am writing to you all today to urge you to not purchase Whirlpool products specifically Whirlpool 2-cu ft High-Efficiency Front-Load Washer. I purchased a front loader washing machine for our tenants through Sears back in June of 2013. When it was hooked up it had an error code on it so we contacted Sears and 3 weeks later they sent out a repairman telling us it needed a new motor (this machine had not even washed 1 load of laundry). They ordered the part and Sears paid 1200 to replace a part on an 800.00 washer.....yeah I know dumb right. Well the part replacement did not work. (Surprised) They ordered and delivered a new washer 1 month later....same error code. Lets try again with another washer......same error code. How about another one......water would not stop running into the machine because the sensor was broken. Wait we are not done how about another one.....same error code. No I am not kidding, 10 months later 5 washing machines and my tenants have yet to have been able to wash a single load of laundry. I have been reimbursing my tenants every month for not having a washer for the past 10 months. I finally had Sears reimburse for the washer which they will pick up soon. I am out all the interest for the past 10 months for a product never used. To top it all off I called Whirlpool directly to see if they would be willing to at least give me a coupon for any amount toward the purchase of a different washer. They told me quote We dont do anything to compensate our customer for their troubles. That is the icing on the cake folks!!! I will never purchase another Whirlpool product and I encourage you all to not as well. I want to show them how not caring for their customers can impact them. Please share if you can, but more importantly please pass the word!!!!!

Cabrio top loading washer - I have had this set for 3 years. The first 8 months it was fine, then came all the rust. I had to go to the BBB and file a complaint as everyone at Whirlpool would not help. Last year they finally replaced the top, and now, its rust yet again. I rinse and dry the machine when I am done using it. The repair man said it was because manufacturers are not using primer and just one coat of cheap paint. What now? Ill see if I can get the lid off and sand it and use rust preventer on it. Never again, I should just junk this piece of crap and Whirlpool should shut down if they cant make anything worth our hard earned money.

We purchased a 4.8 Cu FT High Efficiency Front Load Washer in February of 2016. What a nightmare. Just a few months after having it, we kept getting an E3 error message that would not go away. After 2 weeks of waiting before a tech could come out there replaced a door mechanism said it would be fine. After the next wash same thing, same problem. Could not even open the door to get my laundry out. Again they could not get a tech out for at least 2 weeks so Im stuck with the cost of getting my laundry done elsewhere. This time it was the motherboard. Had to wait a week for that to be shipped out. This was all completed in June 2016. We are now the beginning of September and same problem. Again we are told at least 1-2 weeks to get a tech out. Seriously Whirlpool, we are your customer. I have a family and we need to wash our clothes. We spent $1200 on this machine only to have to take our laundry to a public laundry mat because your machine keeps breaking down. They will not replace the machine even though this is the 3rd time with the same problem. The customer service is horrible. They are not willing to help in any way to get this fixed much sooner for her or give us a new machine. This one is obviously a lemon! I will never purchase any Whirlpool appliance again and I suggest based on some of the reviews on here no one does. Next appliance I buy I will do more research for sure.

Bought this machine in Feb 2007 as a pair Whirlpool Cabrio. I loved it for almost two years. The control board went out, Whirlpool replaced it. A couple of weeks later, the F-1 codes started then the F-51 codes. On July of 10, it was code after code. It sounded like a jet taking off and constant unbalanced load. I called repairman and was told to go buy new machine as repairs would start at $500 and since I live in a rural area, no one wanted to waste their time. Two repair techs told me point blank they wouldnt even touch it. We paid $1000 for this machine and we live pay check to pay check. I spent four months trying to get Whirlpool to do something. I kept getting told I should have bought extended warranty. Machine has been sitting under stairs for over year waiting to see if class action or recall can be done. Also when control board was replaced, the repair man told me it was rusting away from the inside out. My husband had to find us a used washer and this thing has done nothing but cost us money. So much for efficiency. Everyone posting here also needs to go to Whirlpools Facebook page and post there.

I have on more than one occasion and with small or normal loads had the washer stop and will not drain. My landlord says he bought the washer 2 years ago and it is my fault the washer wont drain. I read the instructions and can manually drain it but I shouldnt have to do this every time I wash. This has happened 5 times now and I am considering moving because of it since my landlord wont call a repairman to get it fixed.

The salesperson was great but we are not happy with our washer. We already had it swapped out once because of white spots showing up on our clothes. The only thing they could think of was that the bleach I used wasnt rinsing out completely so it showed up on our clothes. Recently, I washed a table runner by itself and it had some red in it. Now there are red spots on a couple of items that I washed after the runner. My husband just now asked why there were red spots on a shirt that he wears all the time. I explained. Also, we have had some white spots on clothes and I could scratch it out without leaving a permanent mark. Were no longer using bleach and we use only liquid detergent and all of it is HE. So I dont understand the machine. I hate it.

I bought this machine in September of 2014. Six months later I HATE IT!! It does NOT get the clothes clean and dont even try to bleach white towels or socks, it doesnt pump the correct amount of hot water and things come out just as dirty as when they went in. It tangles everything together and frequently stops working because it unbalances the load with its lack of water. Ive always been proud of how my familys laundry looked and now Im just embarrassed. Im considering donating this to a human society for dog towels. Stay away from this washer, its horrible. Im going to the laundromat and shopping for a new machine ASAP!

In the past 8 years, I have had to replace 2 Whirlpool Calypso washing machines and 1 Cabrio washing machine. All 3 washing machines worked great for the first 2 years. I purchased the Whirlpool extended warranty on all 3 washers. The first Calypso had 12 repairs done on it. Finally A&E repair service deemed the washer not repairable. Whirlpool replaced the Calypso with a new Calypso. Based on the problems with the first one, I again, purchased the extended warranty. Again, after the manufacturers warranty expired, I again had issues. After numerous repairs, A&E deemed the washer unrepairable. I contacted Whirpool warranty service and was told that they would reimburse me 75% of the cost of their choice of a Whirlpool washer! Since I have had 10 hand surgeries, I need a washer that does not have an agitator (hence the original Calypso purchase). The model that Whirpool warranty deemed as a replacement had an agitator and was also a much lower energy efficiency rating. I found that the Cabrio was a comparable replacement model and finally Whirlpool agreed to replace the washer at 75%. I was angry that they didnt cover the total replacement, but felt at least I got a totally new problem-free washer. I again purchased the extended warranty. I got the Cabrio in March of 2008. In April of 2011, the washer started getting rust around the bleach dispenser and also I would get UL code (Uneven Load). A&E tech came out and replaced a bearing. He said that the rust was not covered under the warranty. I asked how it was okay to have rust around the bleach dispenser if the washing machine is always wet with water. A month later, I was still having a UL code and the rust was getting worse. A&E came out again and said that even though I saw rust around the bleach dispenser, the rust was in fact underneath the tub and had eaten away at the parts. He called the warranty company to authorize repairs and the Whirlpool warranty company denied any more repairs on the washing machine.

Whirlpool Cabrio Platinum Washer - The seal on the top of the drum is breaking down. It is cracking at the bleach and soap dispenser. Somewhere in the washer drum or plate is causing holes and cuts in the clothes. The machine is only 2 years old.

We purchased a Whirlpool Cabrio washer 6 years ago. This washer has been such a terrible appliance, I would not recommend that anyone buy one. The top of the washer has broken 2 times. Whirlpool will do nothing about it. It is a manufacturers defect where the glass pops out of the top and then breaks the frame it is in. We had it replaced last year and the new one is now broken - same problem. It also does not get clothes clean and the clothes get ruined because they become all entangled in one another. We will never purchase a Whirlpool appliance again. I did have a 5 year service contract on these appliances but once out of warranty - you are on your own.

Whirlpool Cabrio WTW8500DW0. Like: Top loading, Handsome appearance, clear glass lid, easy access soap dispenser plus separate Oxi dispenser. Dislike: Does not have a soak cycle. We didnt realize until after we replaced our old Sears Calypso what a really poor job it was doing. It damaged the clothes and never really got them clean. Also, the small capacity made it nearly impossible to wash large items such as bedspreads or comforters. The Whirlpool Cabrio WTW8500 has be a delight.

Purchased on Nov 2010 at Lowes. Washer machine sounds like an airplane on the wash and worst on the spin cycles. Bearings are gone!! Customer service was no help. Basically was told I was ** out of luck. Have service bulletin addressing this issue, yet they refused to help. $1300 learning experience about Whirlpool. Social media here we come. Goal: to keep at least 1 million customers away from their scrap!!

I owned a Kenmore washer for approx. 20 yrs that endured 6 kids for most of that time period. When time came for a new one, I had to have the latest model, and settled on a Maytag Bravos approx 3 yrs ago. This was a huge mistake - I paid between 600-800 for this machine, and it is a piece of garbage. The repairmen here yesterday explained to me that Maytag and Whirlpool are now the same company, and also that all these machines are now made overseas because of cheap labor. In a nutshell, I was given an estimate of at least 300 to repair this piece of crap - he explained that they are only made to last a few yrs -where is the justice in this situation? I really dont get how these big companies get away with selling crap, knowing all the while that the consumer is getting screwed - yet people continue to buy them..

Duet Washer GHW9150PH0 - The washer is about nine years old. Last year I got the dreaded F-11 error code, and had to purchase a new controller board and install it. Now the spider arm on the basket has snapped (cast part). Ive been on the phone with Whirlpool for over a half hour now, and all I get is We have to send a service tech out, and you have to pay for them. I have the broken part in hand, I know the Whirlpool part number, yet they want me to pay for a tech to come see the part and confirm it. Ive been unable to talk to a manager yet, none are available.Eventually the lady agreed to replace the broken basket, after telling me at least five times she could not, but she refused to replace the tub which was destroyed when the basket broke. Ill be calling back to talk to another agent soon.

Never ever plan to buy a Whirlpool product. I took the washing machine in December 2008. System was not got at first time also. I called service center, and he came and asked to put this and that. Again, it got a problem. This time, he told me to change powder. I was shocked how a powder became a problem for its failure in washing clothes. Next, he told me to put a stand. After a long interval of 6 to 7 months, I got fed up and called him again. He told me it was not in the warranty. Its the worst service. Zero percent satisfaction Hats off to Whirlpool service. Please, friends, never buy cheap Whirlpool products.

Purchased this washer 7 months ago. We are a family of 5 with A LOT OF LAUNDRY!!! I adequately researched a machine that could do large loads of laundry, WELL. I read at least 100 reviews and went forth. (Note to self that anyone giving this machine a decent rating, is a DIRTY, SMELLY, FILTHY LINEN WEARING FOOL who doesnt take much pride in their clothing cleanliness.) I proceeded onward and after paying A LOT OF MONEY for this 4.8 Whirlpool Cabrio Washer, I found out within the first two days of owning it, that IT IS GARBAGE! Regardless of the 4.8 drum size, you can only fill it less than 1/4 of the way with clothes, to even hope they will be touched by water. My clothes come out DETERGENT STAINED & DRY! Insanity... A washer that doesnt wet the clothes!!! We have had 4 repairmen come out within this time, because I am fed up! I have been physically shown and told now, by all 4 guys, that the washer will not fill more than 9 inches with water. They advised me to fill Home Depot buckets and throw them into the drum. THIS IS WHAT I DO, TO SATISFY THAT I AM WETTING MY LAUNDRY - PURE CRAZINESS! The repairmen told me to set all loads to bulky sheets + extra rinse + highest soil. This is a 1 hour, 26 minute initial setting. Note that my adding water messes up the computer readings and it will reset throughout the washing cycle multiple times. Even with all of this... the machine still doesnt wet the clothes!! The top and center of the load is BONE DRY! This machine will not wash sheets, blankets or comforters, either. Dont waste your time trying!!! Dont be fooled by the drum size. Your great grandmothers 1930s 1.6 cu ft washer washed more clothes in any given load. #1 My water bill is through the roof. #2 The washer constantly resets and runs on any single load for over 2.5 hours AND #3 MY LAUNDRY PILES HIGHER AND HIGHER, as you cannot put more than a smattering of clothes in the machine, at any given time! GARBAGE, GARBAGE and MORE GARBAGE!!! I would be better served to find a stream and a flat rock and start doing my laundry colonial day style! I am done... Finally had enough of this insanity! RETURNED THE MACHINE THIS MORNING!!!

We have had this washer for a year and the longest it has run before breaking down is 3 weeks. Since it takes longer than that to get a repairman out to look at it and another 2 to 4 weeks to get parts, it has run less than half of the time we have owned it. This thing is a hunk of junk. Dont ever consider purchasing one of these lemons.

I bought this top loading, low water machine 1.5 years ago, $500.00, did not buy extended warranty, expect major appliance to last at least 5 years. Motherboard is out, will not spin, will cost at least 200 to $300 to get it fixed! Selling on Craigslist for 50. So sad. Will never buy whirlpool again, waste of hard earned money!

We just purchased this Whirlpool Washer. It is so awesome. Has all the many features I was looking for & we purchased it on sale. But really since using my washer I would buy it again even if it wasnt on sale. I love it. I have never been disappointed with Whirlpool. Everything I own in appliances is Whirlpool.

I purchased my Whirlpool Duet Steam Washer and Dryer 4 years ago. My laundry never had that moldy smell. I paid for the set almost $2,900.00! Never again Whirlpool for sure!!!

The Cabrio washing machine I was told by salesman best made so I spent big $$, makes sense right?! Wrong! During spin cycles sounds like jet plane taking off, was told barrings or drive shaft is at fault cause water seeping inside, causing rust, Whirlpool didn’t seal it or designed it to ensure no seepage. Never again Whirlpool. I’m done with your ineptitude, Type: 580. mod. WTW6500WW1. Set.# CY4970595.

I bought a whirlpool Washer in 2011 which I bought an extended warranty. Thank Goodness! It has broken every year. At first I was ok since they always fixed it. It is very inefficient and the clothes are not clean. But today I am so ticked. It broke in Sept. and they have come out twice and cant fix it. Now they say it will be Dec. before they can fix it as part is backordered. REALLY!!! Im expected to not have a washer from Sept. to Dec. with no compensation! I have called both Whirlpool and the warranty company and they say thats just the way it is. I WILL NEVER BUY A WHIRLPOOL AGAIN. The warranty service is through Federal Warranty Service.

These washers are known to rust terribly from underneath the bleach dispenser. Please note that if not detected within the 1st twelve months from purchase, then Whirlpool will not stand behind their product. I would highly recommend not purchasing the Cabrio top load washer. Extremely dissatisfied with this product and warranty.

I purchased the Whirlpool Cabrio washer in 2011. It has been nothing but trouble since. I have had repair people out here several times, because the machine twists and tangles the clothes, doesnt get the clothes clean. Sometimes the clothes come out dry without even getting them wet. There are lots of soap scum too. I would NEVER buy another one of these. SO DISAPPOINTED.

I purchased a brand new Whirlpool Cabrio Washer from Sears less than 5 years ago and am junking it! It has all the same problems everyone else has mentioned. I have had it serviced for faulty motherboard, unbalanced tub, broken lock mechanism. It had rusted out on the inside. Clothes are never clean and it constantly becomes unbalanced in spin cycle. We have to stop and rebalance every single load 3 or 4 times--or more if trying to wash a set of sheets or two or more towels. Cant leave the machine unattended for even a few minutes. I might as well be hand washing on a scrub board at the edge of a river! Waste of money and Whirlpool Customer Service wont say anything but should have purchased extended warranty! What a load of crap from what was once a reputable company that used to make a reliable product. WARNING--NEVER BUY A WHIRLPOOL WASHING MACHINE!!!!!

This is the worst washing machine Ive ever purchased. Bought 12/19. The water level never never goes up high enough, to cover the cloths. I have to add water no matter what setting. I hate that. The sensor isnt working. You arent able to adjust it yourself, its computerized. The water shuts off when you lift the lid so you cant rinse out the soap or fabric softener caps. I hate that. The lid locks when the rinse cycle starts so I have to unlock the lid to add fabric softener. Why lock the lid so soon, wait till its in spinning mode. Really really badly designed!!!! Will never buy anything by Whirlpool ever again!

I have owned the machine for 1yr and 6 months, bought new from reputable company. The washer always had kind of a clunk sound which the manual says is normal. Clothes would have white marks and streaks after was but disappear when dry. Clothes would seem damp, never like they were completely washed. Went to do a load last night and thats when it stopped working. Powered on, cycle selection was fine, lid locked, typical clunk noise, then nothing, no water. Paused the cycle, lock lid light flashed but didnt unlock. Machine powered off on its own and unlocked. I powered it back on after 30 minutes and it wouldnt let me change the cycle, panel selection was frozen. So I powered it off and contacted repair. They think its the water inlet? Pending repair to see for sure. This is not OK! I had an older machine from the 90s that was still working before I bought this one. So sad to have this type of product from this company.