Purchase 2009 Duet Washer & Dryer (WFW9700VW00). Recently have had error codes coming up - F35 for one. Could not get washer to reset. Had to keep unplugging and plugging back in. Service was called and the tech knew right away what was wrong. He ordered and installed an analog pressure switch. While he was working he mentioned that this was a known error and if we had called with this problem a couple years ago Whirlpool would have replaced the washer. Im not looking for a replacement but I feel Whirlpool should cover the part having been a known issue.

Im so tired of the mold smell that never goes away, even after following their cleaning cycle many times over. I dont know what to do but I spent extra $ to purchase my washer and now this!

We bought the Whirlpool Cabrio set from Sears in February 2010, for our second home. We counted up the weeks we have actually been here since then, it is about 10 weeks. We figure we used the washer about three times per week. So, we have gotten about 30 wash loads from this washer and it dies mid-cycle. We assume the motherboard crashed. It kicked the breaker. Lid was locked and we couldnt get it open. The washer would not power up. Repairman arrived three days later, got the latch opened but couldnt figure out what was wrong with it. He said it is probably a board and it might be better for us to replace. He wants to pick it up tomorrow to take to his shop. I called Whirlpool to complain. I know the one year warranty is up but to get 30 uses out of this expensive piece of junk and not get any consideration from the manufacturer is not right. I wish I had seen all these complaints before I bought it. No Whirlpool ever!

Whirlpool Cabrio - This expensive machine should be called the Presidential. First it spins, spins, spins. It sprays tiny amounts of water, so little, that there is 2 inches or less. There isnt enough water to cover the clothes so no agitator to stir and mix them. There are ridges on the bottom of the tub called aggrivators to twist everything into pretzels. This twisting spreads the dirt around, but does NOT remove it, the utter lack of water giving it no where to go. I use a hose to add extra water, and I hand soap dirty spots. I stop the washer frequently to hand rub and slop the clothes around and un-twist them. Explain to me how running this machine 3 times plus adding water saves water and energy. I cant, in good conscience, sell this POS to someone else, and I cant afford something else. I sure miss my simple reliable old Maytag. I could say even more about this atrocity, but not now. I HATE THIS POS!

Ive spent more repairing this washer than what I paid for it new!!! Its really ridiculous that Whirlpool isnt more responsible for their equipment that doesnt stand up to their name! Ive replaced more things than I want to type but just to start the computer board, pump, bearings just to name a few. Each time I had my repairman out it was a minimum of $300 to repair. Ive had my repairman out 5 times to repair things. Thinking each time its cheaper to fix it than buy another which I surely didnt think I would be repairing it several time! At this point Im just sick to death that a washer that is for a home of myself and my daughter has broken down so much. I cant imagine what a family would go through. Even after all the repairs it still isnt right but Im done sinking money into this sinking ship of a washer! Its loud constantly stops due to un level so I have to move the clothes around usually having to repeat this several times before I can get the load to finish!!! Then they come out wrinkled more than they went in and I have to iron clothes. A person should NOT need to iron! May as well wash them in the river on a rock. It would be easier!!! SO DISAPPOINTED!!!

My brand new top-loading, high efficiency washer has squealed like a banshee from day one. Whirlpool replaced the main agitator part, with no success. It still squeals so loud, you cant have a conversation in the same room. Now, Whirlpool says that it is normal. No, it is not normal for a washer to squeal so loud. I am still waiting on Whirlpool to replace the same part they replaced the last time. We are still not abe to hear each other over the squeal of our new Whirlpool washer. This is not normal.

On October 21st 2011, Michael sent their technician, Steve, to my residence to check my washing machine. I was in the house the whole duration of his visit. After testing he concluded that the control board of my machine is faulty. Although he brought with him his own control board but he never showed me my machine working when he installed his control board, even though I was in the house at the time. With my lack of knowledge at the time, I missed requesting that he show me the machine working with his control board. But he should have involved me in the diagnosis since I was just home and should have been his initiative. Anyway, Steve then said that the total cost of the control board plus service is $194.03 on top of the diagnosis fee of $81.19. I was taken aback with the cost since working used washing machine on Craigslist just cost $150. So I said I can only pay him for his diagnosis of $81.19 by personal check. He issued me an invoice with account number **. I also thought that I also could get a cheaper control board online which I did. Also, I know I have the right not to purchase control board from them as long as the diagnosis was accurate since I paid for it. So I ordered a control board from ApplianceZone.com and also chatted with a technician named Kelly. Based on the symptoms I related to her, Kelly confidently said that the issue is not with the control board but the Control panel is the one that is faulty. Kellys diagnosis was different from Steves but since Steve has personally checked my machine, I decided to purchase a control board. When the board arrived on Octpber 25th, I immediately installed it as its easy to install since I followed simple instructions how to install it myself. But when I installed the new control board it manifested the same issue as the original part.. So I called Steve over the phone and he said the new control board.I purchased also faulty and that I have to replace it which I did. Then the second new control board arrived on November 8th and when I installed it, exactly same issue again manifested. That was then I suspected probably Steve misdiagnosed my Washing Machine. So I tried calling Depew the same day but wasnt able to reach Steve. Instead another guy named Kenneth answered the phone. He said that Steve has the right diagnosis but I insisted that I recalled Steve never showed me the washing machine working with his control board installed so Im doubting he got the correct diagnosis. Since it wasnt helping me at all, I decided to visit personally their store on November 8,th 2011 at 5933 Burnet Rd Austin TX, to request an audience with their manager. Then I met the manager named Michael ** who I believe is also the owner of the company. After introducing myself and explained the issue and told him that I wasnt satisfied with the service rendered by Steve because with two new control boards why is my machine still not working so I believe Steve got an incorrect diagnosis. I was a dissatisfied customer and I was hoping they would find a way to help me since I already paid them $81.19 but to my surprise, this Michael ** was so rude, his response was We have done our job, you are on your own now. We dont need your business. Good Bye I said Is this how you treat your customers? he answered me This is how I treat you.. I felt discriminated and insulted by his unprofessionalism. I couldnt imagine an owner of a business treating a customer like that. Before I left, I told him that I will report him to Whirlpool since they referred Depew to me and I would also report to the Texas Attorney General. He just said Go ahead and do what you want to do. We have nothing to do with you; I couldnt believe we have a business owner like this here in Austin TX. I really appreciate you helping me with this issue with Depew Appliance especially with this issue with their manager Michael Depew. I also demand refund of $81.19 for the diagnosis as they dont deserve to be paid and also they should pay me the cost of the control board $85.13. Lastly, I like to request that whatever license this company is holding must be reviewed as his dealing with me as customer is nothing short of discriminatory.

We purchased the Whirlpool washer less than a year ago and are now having the 4th transmission put into it. We are also having the 3rd timer put into it. We purchased this from Sears and bought the extended warranty (thank God). One of the times the technician ordered the parts to repair the machine. The service center sent the wrong parts and we had to wait an additional week for the correct parts to arrive. The 3rd transmission they installed lasted a week before it leaked gear oil all over our floor. When you do get a service call scheduled it will get rescheduled to a later date. This happened twice. They also cancelled the service call once before they fixed the machine. If I could give a zero star for this I would. DO YOURSELF A FAVOR AND DO NOT BUY A WHIRLPOOL WASHER AND DO NOT I REPEAT DO NOT GO TO SEARS FOR ANYTHING. Worst company to business with. I will say this that the service guy that comes out to do the work is a good guy. He stayed until almost 9:00 pm on one of the service calls. Hes been here so many times our dog knows him and doesnt bark at him anymore.

I purchased a Whirlpool Washer at Lowes on 02/29/16. After 3 weeks it simply stopped after the last rinse, never drained the water or starting the spin circle. One and a half month later after 5 service calls still no working washer. Whirlpool customer service just adds insult to injury. They refuse to replace to washer or to issue a refund. Apparently they dont care if their customers have to use a laundromat indefinitely after buying one of their washers.

I purchased a new Whirlpool Cabrio washing machine from DeWaard & Bode at Bellingham, WA in January of 2007. The serial number is **** and the model number is ****. Several months ago, the dreaded F1 code appeared. The code initiates when the washing machine is started and must be cancelled and started 3 times to continue washing. Later, with approximately 19 minutes left in the cycle, the code reappears and requires canceling and restarting another 3 times, at times 4. I have no extended warranty so I have no coverage for repairs. I also dont want to pay for a service call for what is most likely the computer module as evidenced from the majority of complaints online. This washing machine still looks new and works other than the inconvenience of having to stand by when starting the cycle to reset the code and then having to run upstairs later to reset the machine when its partially through the cycle. At some point, it will likely quit operating all together. I have purchased several appliances over the years from DeWaard & Bode and will be replacing all kitchen appliances again next year due to a planned remodeling but at this time, I do not intend to get them locally due to this issue. I have reviewed several comments online and feel that Whirlpool has a real problem with this particular machine that they refuse to be responsible of. I was offered an extended service plan for 1 year at $132.01 or 3 years for $336.61 but Id have to wait to be allowed to utilize it due to existing circumstances. Im not sure if a fix is actually available. The local dealer did not offer any assistance.

I bought a whirlpool washer from Whirlpool on February 27, 2011. Since then, they have come out and repaired the washer for 5 times. They have even taken the whole motor out, and replaced it. The last time they came, they said I would have to pay for the next time. Now, it has broken again, and I have to pay for a washer repair that is less than a year old. We bought the Whirlpool washer at Sears, and neither Sears, nor Whirlpool will stick by their product. We cannot afford another new washer, and to pay for repairs is a stretch too. Is there anything you can do?

I am a retiree after 35 years and 5 months, the last 20 plus years on salary. I purchased a new Whirlpool washer on April 18, 2012 at Lowes in Tiffin, Ohio. The clerk said to take the receipt to Clyde to apply for my rebate. I was informed by a receptionist that we only get a rebate if our purchase is from Sears. I only went to Lowes because of the urgency and was not aware of this change in your policy. I consider this a real slap in the face after all the years of what I consider excellent service to Whirlpool Corporation.

I bought a Whirlpool 3.4 Cu Ft. Top Load Washer, Model: WTW4800XQ on Sunday. Today is Tuesday morning, but the machine broke last night. It lasted for about 5 loads and they were not big loads, unbalanced, and yes I had the right amount of soap. Whirlpool is saying that I washed something that was not machine washable. However, that is simply not true. I washed the bathroom rugs (which have been washed many times before) and they are saying the pump is clogged. If I had a washing machine 48 hours ago, do I really have to pay a service repairman to fix it? I will never buy any Whirlpool product again.

After having an expensive front loader (ugh) we purchased the Whirlpool Cabrio top loader (wow)! Best washer ever owned, wouldn’t trade it for any on the market! It has been as great and problem free as the front loader was terrible with cleaning and smell.

My Whirlpool Cabro washer does not get clothes clean. When I contacted the manufacturer, I was told that it is water saving. What kind of water-saving is it if it does not clean my clothes. I would think cleaning clothes require water. If this feature renders the product ineffective, this product should not be in the market.

Bought this machine June 23, 2016. First use, I called Lowes where I purchased it to say there is something wrong as it makes a grinding noise. I was informed that is normal for agitatorless machines. I asked if he could hear the noise, and he said yes, thats it. So I disconnected thinking, Wow, who makes a machine in todays technology that is so loud you think something or someone is in serious pain?! Now am at the point where I want this design in pain out of my house! Going to Lowes today to try and talk rationally for a complete refund so I can purchase an LG or Samsung which is what I should have done originally.

My whirlpool Duet Washer has been repaired twice in three years for more than half the cost of the original product. Now it faces another repair--not worth it!Shouldnt a major appliance last longer than three years? Whirlpool will do absolutely nothing.

I purchased Whirlpool top loading washing machine model # WTW57ESVW less than 2 years ago. It stopped working yesterday. I had a trusted professional repairman evaluate it today. The motor needs to be replaced after less than 2 years?! The customer service reps basically said sorry. I should have purchased the extended warranty. Is it not reasonable to trust that a Whirlpool washing machine motor should last more than 2 years.I am very unhappy and very angry that Whirlpool will not stand behind their product. The last customer service rep I spoke to suggested she could send one of their repairmen and replace the motor at a cost to me of $299.00. So, after less than 2 years, I am offered an amount to pay of about half the cost I paid less than 2 years ago for the brand new washing machine. My home is full of Whirlpool appliances. I have been a good and loyal customer for over 30 years. I am very angry and upset with Whirlpool. Please explain to me why it is not reasonable for me to trust and believe that a Whirlpool top loading machine that is well cared for and not abused in any fashion should last longer than 2 years? Is this being a loyal Whirlpool customer gets you, I should have purchased the extended warranty”? We are talking about a motor here, not a fabric or bleach dispenser that breaks. Although, those parts should not break either, there is a big difference from something like that and a motor. Please contact me as soon as possible at either number listed above. Thank you.

I have no problem with Conns. My complaint is with Whirlpool for making such a terrible machine with the Cabrio Washer. Its a piece of junk.Fortunately, I bought the extended warranty – which was used many times to replace computer modules and pumps. Now that the warranty is out, once again the machine is doing the same thing. Bad codes, not filling, etc... Some cycles you cant use it at all. The cleaning cycle is never ended (literally). I am debating on having it fixed or just getting another machine.

This Whirlpool washing machine is incredibly annoying and slow in everything it does. First off when you press the START button it takes 2-3 minutes before it decides to do anything, like maybe add water (except click, click and more click). If you have pressed the start button and you want to stop it to add something... again you have to wait almost 2-3 minutes before the lock is released and you can open the door. I am at 2 hrs and 15 minutes as I write this on the LIGHT WASH cycle with extra rinse and its still going. I have never seen anything like it. Cant imagine how long a HEAVY CYCLE takes. Cannot even try to measure the time. I put the load in and go to work and hope its complete when Im done 8 hrs later.We had a Maytag for 15 years with no issues (other than a drain hose cracked and had to be replaced) and it was time for a new one with a move to a new place. The sales associate convinced us this was the best machine at the time... Well what a mistake that was. There are no complaints about the actual washing. Everything comes out clean but I suppose taking that long I cant imagine why it wouldnt. I certainly cant recommend a Whirlpool washer to a friend, because I dread the thought of doing laundry at this point.

I bought a whirlpool washer because we thought it was the best. It does not clean our clothes especially my husbands jeans. They are on their third wash at this minute. I use Gain HE detergent. I bought clorox 2, I use spray & wash & I have even started using a little clorox but the red dirt still doesnt come out. I never had this problem with my old washer. If there is any help for me here please let me know. If this is supposed to be a water saver I dont see how I have saved any after washing jeans for the third time. If they are not clean this time, I guess he will wear them dirty.

This is the worst product (Whirlpool Cabrio Washer) I have ever purchased. I paid $999 for it new. I had to have it repaired at the cost of $500 at just two years old. My sister bought and had the exact same repair needed. I used to trust Whirlpool but not anymore. I wont buy Maytag either since it is a Whirlpool product as well.

I purchased this Cabrio top loader washing machine (model #WTW5640XW3) after I had a Kenmore front loader for 14 years with not one problem. I bought the Cabrio thinking it was good for the price. Well, let me tell you first of all, I dont like the no agitator. The salesman said it was a big seller. I started doing wash and it was smelling like dirty socks when it was done. I own the machine for two months. I cleaned the machine with Afresh thinking the smell on my clean clothes was from being a new machine. Imagine that I have to use extra fabric softener, vinegar. I dont know what to do. This machine stinks. I am going to try to return it. Wish me luck. I dont think it washes right.

So I have had the washer for a few years - bought it new or at least I thought. First came a clunking noise - fixed that. Next came the F1 code and installed a new pump $90 plus dollars. After installation, Im still getting F1 code and am now being told it is the ERC control board or water inlet valve either way a guessing game which in the end will have cost me over $400 to fix myself. I wish companies like this would stand behind their merchandise.

I purchased the Whirlpool Cabrio (wtw6600sw2) about five years ago. Last year, the motherboard had to be replaced. This year, it started to have load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $75 to have someone look at it, and to fix it will cost almost $400, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. I called Whirlpool and my model does not have a recall, but models with same problems have been recalled. I will never buy a Whirlpool again!!!

Two months ago, I bought a Whirlpool duet washer and the computer went out, two days after the warranty was up. It went bad that I disconnected the detergent mechanism, which made it work, for now.

We bought a Whirlpool washing machine, and what a mistake! I just got off the phone with their customer we dont care department. It spins everything into a tight ball so when the clothes come out of the washing machine everything needs ironed, even permanent press. It also changes the water temperature. I like to wash some clothes in cold water, but the representative at Whirlpool told me it will sometimes add hot water to make the water warm. I am hoping this review will save others from purchasing a Whirlpool washing machine. We will stay clear of all of Whirlpool appliances due to the problem with this washer and Whirlpools lack of concern of an inferior product!

We purchased Whirlpool Cabrio Washer WTW5600 series in October of 2010. I bought the machine from Sears and also bought the extended warranty. Less than 6 months after I had been using it, I noticed that all my husband’s shirts were getting sweat stains under the arms and my hand towels were very smelly after drying with them one time. I called Sears to have someone come out and tell us what the problem was. He said I was using too much detergent so I reduced the amount of what I was using. It did not help the problem so I started using the extra rinse each time I washed, still did not fix the problem. I called them out 3 more times in 2011. One tech told me I was still using too much detergent so I reduced down to 1 tablespoon like he suggested. I stopped using softener in my washer because he said I needed to clean my machine more than one time a month, to clean it every 3 weeks. No solution to the problem still. I have had a tech from Sears and one from Whirlpool (who incidentally was the same man, he was from A&E Appliances). When he came in the door, my husband told him he had been here before and I said 2 times. He lied and said he had not been out before. Are we blind? No. He ran the cycle but sat in his truck while he was running it. None of the techs have ever put a tool on the machine to check if the water level is right. They just stand there and tell us to change the amount of detergent or clean the machine with Clorox more often. I cleaned it 8 days in a row and the clothes still smell and still do not get cleaned. We talked to main man at Whirlpool and said they couldnt do anything because their 1 year warranty had run out. We have been using Whirlpool appliances for over 30 years but I will not ever buy another one. I have probably had 5 Whirlpool washers over the years but never had a problem until we got this Cabrio top loader without an agitator. I would not recommend this washer to my worst enemy, if I had one.

I purchased the Whirlpool Duet June 2011. Within two weeks, it was tearing my clothes. It didnt matter how little of a load it was, they still ripped. Five months later, my machine was leaking water. The repair man came out. I told him it was also tearing my clothes. His only response was dont load it to full. Well, I called the store where I purchased it and they are sending a repair man out again. I told them to either fix this from ripping my clothes or I was going to take a hammer to the machine and never buy a Whirlpool again or give them a good reference. I also called Whirlpool directly and told them of my problem and they acted like they had never heard of this happening before. I told them to search the internet because everyone is having the same complaint! I had a Fridgidaire front loader for 9 years and never had a problem with it eating my clothes.

We purchased a Whirlpool Cabrio Washer (Mod #WTW7300XW1) and Dryer in 2011. Ever since we have had the washer it has eaten clothing, towels, sheets etc. It now has a main bearing that is so noisy that we have to close the door to the laundry room to be able to hear in the rest of the house. Also the sealed tank around the drum is now leaking. We invested close to $1000.00 in this washer and in my opinion it is a piece of junk. The washer repairman told me that he has had 3 (three) other Cabrios with the same problem in the last month, but Whirlpool says that there is nothing they can do as they have had no issues with this problem. Last Whirlpool product that I will buy.

We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.

I purchased the Cabrio washer about 2 years ago. This summer, I began to hear a roar in my washer when it was spinning. I called a repairman and in order to fix it, the tub has to be replaced and it will cost $258 plus service call. My sister purchased her Cabrio 3 years ago and her washer has the same problem. This sounds like a recall issue to me. I think Whirlpool needs to recall this washer or pay my bill.

I just bought a new home, and it came with what was described as top of the line Whirlpool appliances. The Cabrio toploading washer worked for two loads then just stopped. After arguing with Customer Service for a while (They insisted this must be an installation error.), I talked with the builders. They gave me a different customer service number. My second call got me a repair appointment, during which the repairman discovered that the pump was in fact dead. Because this is a new model, they didnt have a replacement on hand. So, I will have to wait an additional week and a half before the part is installed. This is a product that retails for around $1000, and it lasted less than one day. My last washer cost $400 and was still running fine when I sold it after 10 years. I can already see the handwriting on the wall. After my warranty is up, I will have to replace this hunk of junk with something that has some reliability.

The Whirlpool washing machine I bought is a piece of crap! I only do laundry every 3 weeks/3 loads and the machine broke in 13 months. Now it has broken a fourth time/same part - I have had the machine for 5 years and they can not do anything about it. I will not be buying Whirlpool again - of any kind.

I hadnt had the machine. In no time, I started noticing brown rust looking spots on my whites and light colored clothing. I got to looking and had rusted out all around the bleach dispenser, entire area on the entire top. I was told to replace it. This would be about $200. Ridiculous!

I purchased the front load washer 4 years ago and the board went bad in 2 years. It costs more to fix it than the washer is worth. Stupidly, I purchased the top loading Cabrio and it has gone downhill from there. Has always sounded like a jet taking off in the spin cycle. Then 18 months into the purchase, it started with grinding noises and load balance issues on the spin cycle. Seems like they have a lot of issues with these Cabrios. Spent a lot of money for nothing. I will never buy a Whirlpool again!!!

I purchased this machine in February 2019. The standard one-year warranty covered the first service call less than one year later. This call was related to the main control board. If this part goes out it will prevent the washer from advancing through the cycles. A technician was able correct this problem by resetting control board. That was sometime the first year. The next call was for the same problem and it cost me $90 to have a technician reset the board again. I then learned how to do it myself through online research. However, I had to do it more regularly and this got old as you can imagine. I did buy myself about two months of time by purchasing a used part but it soon failed as well. This main control board cost $564 if you get it from the manufacturer. This exceeds the cost of the machine. It was purchased in 2019. (The same machine has gone up to $740 today.) I had no other problems with that appliance however, it appears nowadays with electronics taking over cycles vs. mechanical parts you will not enjoy the same longevity as I did when I got 16 years out of a GE washer before this one. I have replaced this machine with a competitors product that costs less than the part except for the 5-year warranty from Lowes.

We have had our washer just over a year when the plastic hose that fills the detergent tray began leaking. The entire assembly is plastic and poor quality. Whirlpool customer service says since it is after 1 year, that I would need to pay for the parts & service ($489). I would not recommend this machine or anything Whirlpool.

My new energy-saving Whirlpool washer sucks. Laundry comes out smelling as bad as it went in. Washcloths are as dirty as they were when they went in. I have to take my dogs bed blankets to my sons home to wash them because this new washer will not even clean blankets.UPDATED ON 08/21/2015 - I have had two Whirlpool washers in 38 years. They were great. I buy a new up to date energy-saving Whirlpool washer and it doesnt last a year and a half. Now it is costing me $433 to have it repaired. I am preparing a washer and I am very unhappy with to start with. I will never recommend these washers.

I sold my 4 yr old Maytag and bought the Cabrio 3 yrs ago because of all the manufacturer promising advertising. Its a top load with agitator, but it takes 2 hrs to wash a load and buzzes the entire time. So relaxing coming home and spending my evening listening to this buzz, so loud I have to max out my tv to hear it. With 2 hrs spent washing a load, I can only do one per evening. Whirlpool you owe all of us a replacement or a major discount coupon toward another (50%) if you are worth anything at all. You are scum!

The features on the washer is a wider size wash basket, no non-snag agitator with 5 load size choices, 5 water temperature choices, type of wash includes soak, quick wash, normal, deep water, heavy duty, bulky, hand wash, gentle, some other choices Along with a choice to wash your machine, one rinse or two rinses without fabric softener, one rinse or two rinses with fabric softener. And finally a selection for Pre-soak on or off. Also has a 3 light display for what it’s doing, lid lock, pause, cancel and start button. It’s an HE. Clothes come clean.

I just replaced a 4 year Cabiro washer with a Samsung. The washer was making terrible loud noise when spinning. It sounded like a jet plane. The repairman said it was a bearing that was going out and that it was a common problem in the Cabiro washers. Cost to repair it would be $500.00. Last week, it finally started spewing oil from underneath so had to buy a new washer. I will never, ever buy anything made by Whirlpool. Whirlpool said it was off the one year warranty (duh) and they wouldnt help with repairs.

On its 1st year, the water pump went out. It cost $200.00 to replace it. On its 2nd year, the circuit board went out, and it took $300.00+ to replace it. On its 5th year, the bearings went out and cost $250.00 to replace it. I bought this for $900.00, and I already have paid $750.00 plus the price of purchase which makes this washer $1,600.00. Whirlpool should compensate all of us who have worked hard and have purchased this product! I will never purchase from Whirlpool again. I can’t afford them. I should get a refund from Whirlpool. Don’t they care? Email me for these problems at **. I am so dissatisfied with this product.

This is a top loading, with agitator, purchased from Costco over five years ago. It took some time finding a top loader, which I will always prefer. Very reliable. Have only needed repaired once. Have other Whirlpool appliances, very reliable.. Fridge over 20 years old and no problems, except needing new ice maker. Also, other whirlpool washer we had over 15 years.

I bought a Whirlpool Cabrio Top Load washing machine September of 2012. It has never cleaned the clothes well. For the last month the machine has a very loud spin cycle. I am very unhappy with this purchase and it is 2 months out of warranty. I emailed WHIRLPOOL and was told that all appliances have problems and wear out. WOW! It is 14 months old and has been used with care. I will never buy another Whirlpool product.

So I had a problem with the water heater after 2 years and had the sensor fix by my heating people. Now the water heater is 3 years old and started leaking from the top of the water heater. Called my heating people and they fix the pipe and coupling on top but he told me the water was still bubbling up at the top. He told me it could stop and 70% it would be ok. Went to check on it and it continues to leak so I called Whirlpool because it was still under warranty. They are the most horrible people to deal with. First of all I told the guy it was leaking from the top but he asked me if it was leaking out of the side pipe. Didnt know what he was talking about and he kept sighing on the phone. If I knew about water heaters I wouldnt be calling them. After all the questions it came down to it was leaking where I told him at the top. He gave me a number and told me to take the water heater back to Lowes and get a new one and then call them and they would move the warranty over to the new heater. Really???? We are not talking about clothes you want to bring back to a store. Asked him how I should do this and he told me to call a heating contractor. So does he think that the heating contractor and going to run the water heater back for a new one??? In the end I just called my heating people and they are going to send somebody out to install a new heater. So much for Whirlpools warranty. If this is under warranty and it is exclusive to Lowes then they should be having Lowes bring a new one and install it.

After reading all the reviews about the Whirlpool Cabrio washing machine, all I can say its just a piece of junk. We have replaced the agitator 3 times at $80.00 each, not including labor. Our clothes are never cleaned properly and it always seems to be out of balance. I will never purchase another Whirlpool product.

I purchased a Whirlpool Cabrio set 3 years ago based on their brand reputation and consumer reports. It has been a terrible experience since the moment the warranty expired. First, about 1 month after warranty expired, I had to replace the main electrical board. Then about 3 weeks ago, the drain pump failed. I purchased the $110 pump and installed it myself. Now this week, the spin cycle sounded like a jet engine. I took it apart to find that the bearings were shot on the drive shaft. I figured, well it is just a wear item, understandable right? So I went to order parts and got told that I have to order the whole outer tub for $250 with shipping! For some bearings! I called Whirlpool directly and was given no explanation other than Call some parts distributors. They may be able to help you get the bearing separate, but we dont do that and there is nothing that we can do. Amazing. I equate that to having a faulty brake on my car and being told that I have to replace the whole axle!Fortunately, the washer never really did a great job. It was loud and tore clothes up, so the decision to part ways was not too difficult. I have the list of brands they make and will be sure to never buy another. Im selling this one for parts. Im sure there are others out there that will need a pump and control board soon!

This machine, like all other water sensor machines, will not let you wash a few items that are lightweight without filling the whole machine up almost all the way. The reason being is that if the items are light, they will float in the water above the water level and the sensor thinks it needs to put more water in and even with putting something in to weigh it down like a wet towel doesnt always work, nor should you have to do this. You will waste more water in the long run if you only have a few items to wash, ie baby clothes, underwear, rags, etc. I am so disappointed that I had no other choice but to get this machine.

Whirlpool Cabrio Washing Machine F1 code - We have had this washing machine for over 6 years now, and ever since our 3 year warranty time was up, the washing machine will only stop, and display the F1 code as soon as the wash cycle has completed, with 23 minutes left. To start off, with this problem, it is causing me more water, and electricity that should not have to be wasted if the machine worked properly. I called the place where I got the machine, and was told to give Whirlpool a call. I did this, and was told that there was nothing that could be done, and if I would like to schedule an appointment for a tech to come out and work on it, they could do that. YES, I would have to pay for it. Needless to say, the washer has been doing this for over 6 years, and if there is a way to get it fixed WITHOUT having to pay for the repairs, that would be wonderful.

I purchased a Whirlpool washer 7 months ago, and a month ago, it broke. I have been without my washer for 1 month, and it has been repaired 4 times in that month. It is still not working. All I get is that, its under warranty, and there isnt anything they can do, but to keep trying to fix it. I have been having to take my clothes to a laundromat, and pay to have them washed. I have asked for them to deem it defective, but they refuse.

Installers left and Home Depot Cabrio washer stopped with water left in tub. I reset GFIC outlet, tried again and it stopped. Did some research and tried different outlets. Same result. I discovered that if you shut off machine as soon as the GFIC is reset, then the washer will drain no matter what. I have been on the phone with Home Depot and they have no solution but to wait one week for a repairman. Very dissatisfying service. Now I am running a 20 foot, 3 prong, heavy duty extension cord into living area where there are no GFIC outlets and it has been running. I believe there is a fault in the washer, but they must not care if we get electrocuted from the faulty grounding of their Whirlpool product.

I owned a Maytag washer for 30 wonderful years, so I of course bought a new one. I have battled with my Maytag (Whirlpool) front loading stackable top of the line washing machine for 2 1/2 years. It will not drain, yet sometimes it will. I have played every game with this machine to figure why. I had a repair company out 5 times while it was under warranty and they could never find the problem. It is totally unpredictable. If I could bill Whirlpool for my time and anguish I would own this company!They now say it is the computer board and I will have to pay $350 for a new service contract to fix the machine. I not very politely said that they should pay me for all my emotional abuse. They offered me another option saying they would pay for a service company to come out and look again. However, I would have to pay the labor and material cost. Since I have a stackable unit and it would take 2 technicians I would have to pay $90 for the second person. I was so mad that I called Whirlpool back and they refused to offer me that $350 charge and just said sorry. I are fortunate to have a lake house which needs a new washer. Guess what? It will NOT be a Whirlpool product. I wish I could go to the store where I purchased this holy terror and picket!

I bought a high-efficiency Whirlpool washing machine in August 2011. One week after the warranty ran out, it stopped working. I called Whirlpool who, of course, would not fix my problem because I no longer had a warranty but did put me in touch with a repair company in my area. They came out and fixed it for 100 bucks, service and parts (service, of course, cost more than the part/labor). I didnt mind the hundred bucks, whatever. My washer was working again.Two weeks ago, I experienced yet another problem with my washing machine. Now, I understand machines getting used a lot over the years and eventually burning out, but this machine is a little more than a year old. I should not be experiencing problems with such a new machine. The problem was when the machine reached the spin cycle, it would just stop working and then lights would start blinking, blah, blah, blah. I called the repairman again who came out and reset my machine, hoping that that would work. He then told me if it happened again to let him know and he would have to replace the motherboard. Okay, I can live with that. Another 73 bucks, thats fine. Of course, this didnt work, and we ended up replacing the motherboard. Another 178 bucks - thats $324 that I have now invested in a washing machine, half of what it cost to begin with. But its an investment, right? And I need clean clothes so whatever.I was a little wary when the repairman told me that a problem with the motherboard may be related to a problem with the motor, that it can send signals to the motherboard if its not working and is just a symptom of the actual diagnosis. I guess he was right because 3 loads into using my newly repaired washing machine and the same problem has arisen, yet again. I refuse to invest any more money into what is obviously a lemon. Rest assured I will never again purchase a Whirlpool product, regardless of what type of appliance it is.

I hate this machine. I stress whenever I have to do laundry. The worse machine I ever owned. Stay away from it. It is a total rip off... I wanted to replace my front loader machine with a top loader. Based on good reviews at the time I purchased the Cabrio. Nothing gets clean. The detergent stays on the clothes and unless I use the Bulk senor. Otherwise I get horrible white marks on all the dark clothes. I cant even get the marks off with a wet rag. So washing only a few items I have to use Bulk. The sound is so bad from the machine, my dog runs in the closet and shakes. I feel so bad for her. How can a popular name like Whirlpool make such an inferior product? They dont even stand behind it. Customer service stinks. Never will I buy a Whirlpool product again. Now, I am trying to save up to buy a new machine. Shame on you Whirlpool.

I owned a Whirlpool Cabrio washing machine for 3 years (a two person household). The repairman just quoted $700 to repair a faulty center hub seal and bearing. This machine was not inexpensive. I expect more from a quality machine. A telephone call to Whirlpool resulted in two ten minute holds while being shuffled between representatives and each representative tried to sell me an extended warranty for another $289. Whirlpool should take full responsibility for this faulty product and not act like a telephone support center located in Eastern Europe. I am not pleased with this (lack of) resolution and do not plan to purchase another Whirlpool product.

I bought a Cabrio washer in late 2015. All Ive had is trouble with this joke of a product. After three years it wont do any cycle, the people at Whirlpool dont care. Please dont buy any Whirlpool product.

It is a top of the line washing machine. I have had it for almost four years. It is the best washing machine I have ever had. I have really enjoyed it, because; I am able to wash my comforters in this washing machine.

The washer has rust under the rim in the inside - also the paint is bubbling and peeling under the rim of the washer. I contacted Whirlpool and was told that is a cosmetic problem. There is no warranty for rust or peeling paint. I will never buy another Whirlpool washer. I paid over $700.00 for this washer and I dont think I should have a rust problem after 5 years.

Purchased this Whirlpool Duet washer WFW920ww00 in 2011. 6 service calls while under 1 year warranty. The mother board was replaced..... after I smelled smoke and burning. Had trouble draining.... error codes F9E2 and F9E1 and SD (suds) and low flow were the usual. At times took 4-6 runs to get it through to point where I could open door. Often need to unplug for 20 minutes in order for it to progress. Clothes would not ring out... or be floating in water. Lately had to run on medium spin just to get it to work at all. The odor/smell was horrible and the rubber ring was black with mold after the 1st year. Completely stopped working this week, no power to panel. The repair shop said to not bother.... he has had customers replace 2 or 3 major parts in these and still keep getting the annoying error codes and difficulty making it through a complete wash. Moving on and buying something else.

I have had a Whirlpool washer for less than 1 year and have had it serviced over 7 times with drain problems - code A10 being displayed. Have not been able to resolve the problem with neither the dealer nor the manufacturer. What a lemon!

I purchased a Whirlpool cabrio mod. wtw5840bwo washing machine in Oct. of 2014. As of June 2015 I am ready to kick it to the curb. The washer works to it design and hasnt broke down but it doesnt clean our clothes. We load the machine, add the right amount of clothes and recommended detergents and 1hr later after the wash cycle is completed, the clothes still stink with the smell of daily perspiration. I went back to using our old washer that has a worn out agitator. It does a better job.

I have called and emailed Whirlpool numerous times, complaining about the fungal odor emitted by my Whirlpool Duet front-loading washing machine (model #WFW9400SU01, serial#CSW0416732). I did everything they suggested that I do to no avail. A customer service representative said that the only thing left to do was to schedule a repair with a Whirlpool service person which I did. He called me when he was on his way and asked me what the problem was, and he told me I would be charged for nothing because hed seen this problem many times before and theres nothing he can do. Please advice.

We purchased a Whirlpool Cabrio Washer in 2010. I have had nothing but problems trying to wash black/dark clothes, it leaves white stuff. I assume its soap scum all over the clothes. Ive tried cleaning the machine with Refresh more often than recommended and it still has the same problem.

Whirlpool Cabrio - What a nightmare. One year in… from the beginning the washer completes a cycle without attention. It gets stuck in a rinse cycle and eventually stops with an FF error display. Because of this it wastes HUGE quantities of water and takes far too long to actually wash clothes. It is so frustrating. We will buy a new Bosch and THROW this way. We cant even pass it on to our grandchildren.

I replaced our old Whirlpool washer that we had for 10 years with a new Whirlpool high-efficiency front load washer in August 2020 - it quit working on December 11, 2020. Got a repair person through Whirlpool on December 22nd who said I need a new motherboard. I am still waiting!!! 42 days with no washer and Whirlpool has no answers regarding the parts arrival and I can’t even sell the thing and get another brand because it doesn’t work! I’m beyond angry!!

My son purchased a Whirlpool Cabrio washing machine about two years ago and now it doesnt work. It was an almost $1,000 machine. You would expect a higher quality product. I always bought Whirlpool products because they were so dependable so I recommended my son to go with Whirlpool. Big mistake, the panel lights up but when you press the power button, nothing happens. I do not recommend this machine to anyone. Im wondering if anyone else that has purchased this has had the same trouble.

I bought my washer machine because my other one died on me. I was nearly everyday so I needed a dependable machine but also good price. This machine is both and I would definitely recommend Whirlpool.

We just purchased this Whirlpool Washer. It is so awesome. Has all the many features I was looking for & we purchased it on sale. But really since using my washer I would buy it again even if it wasnt on sale. I love it. I have never been disappointed with Whirlpool. Everything I own in appliances is Whirlpool.

Whirlpool Cabrio 4.3-cu ft High-Efficiency Top-Load Washer - I wanted to buy American. My Sears front loader (I had for 13 years) died and I couldnt get someone from Sears here to fix it. So I bought this Whirlpool from Lowes 4/20/15. I want to be able to wash sheets, towels, clothing and sometimes a blanket or a sleeping bag. I re-use my washer water for the garden and use no chemicals or fragrance in my washer soap. When I bought this, my washer had died. I was kinda desperate to buy a new washer. I went to Best Buy and Home Depot. There were ads all over Lowes advertising: Same Day Free Delivery + Installation. While there was no one in the Appliance department, I went to track someone down so I could pay and get out of there. I was told that it would take 10 days to get any of the washers I was interested. I didnt have 10 days, so I called my appliance repairman and he came to get the washer and install it. The deal breaker is that this machine vibrates the clothes clean - not water, so the fabrics are trashed and the sheets get all tied up. I had the factory repairman come and he told me you cant do comforters, more than a sheet or towels in this washer because its energy efficient! I should take my towels and sheets to a commercial place!! I called Whirlpool and wanted to exchange for another and they were not at all agreeable. No one else complains. Even after I looked on the internet for reviews on this machine 250 out of 350 had the same complaints as I did. I cant even donate this to a homeless or animal shelter if they dont suggest you wash sheets and towels in it!!! This rule was nowhere in the literature and the info on the top door doesnt say that either! Imagine my dissatisfaction!!! What homeowner doesnt wash towels and sheets???

My Whirlpool Cabrio Washer is less than one year old and quit working. Sears was supposed to come out and fix it (I even have the extended warranty till 2014). Service never showed up; when we called, they told us we had been rescheduled. Here it is the rescheduled day time slot and they still have not arrived. Im getting the runaround from them and I am supposed to be grateful because they gave me a $75 gift card for my inconvenience. Im on hold with Whirlpool because I just want them to take the washer back. I have been told by Sears since it is over 90 days, they cannot refund my money. I just have to wait for a repair which may or may not happen since they may not have the parts. This is unsatisfactory service from both Sears and Whirlpool. I have always bought my appliances through Sears and they have always been Whirlpool. I wish I would have read all these reviews before I purchased this model.

I purchased a brand new Whirlpool washing machine only 2 yrs ago. Rather than lasting upward of 10 yrs with normal use as advertised, the machine is nothing more than a giant wash tub. It doesnt Drain and Spin properly. The clothes are still wet at the end of the cycle and I have to either attempt to wring all items by hand or set the machine to Drain and Spin for a second time. Now, it no longer agitates the clothes during either the wash or the rinse. I am SO disappointed in this and very angry that I trusted this well known brand with my hard-earned money. I am also angry at myself for not reviewing internet posts as I am hearing the exact same experiences by others time and again.

I purchased my Cabrio washer in April 2011 from Lowes. Huge mistake. The washer has broken 4 times under normal family of 5 conditions. The last time was in March 2015 - the barring was stuck on the drum failed to allow it to spin. It was stuck to the point where the unit needed to be shop repaired. It took 2 weeks to remove and replace the fail part. I just called service again today for the same noise as last time. It kills me that I spent so much $ on a product from a well-known company only to have it fail so often.

I called customer service line regarding my Cabrio Automatic Washer (Model No: WTW6600SW2; Serial No: CU2171019) purchased on 11/24/07, to report and ask for assistance with a chronic ongoing service problem. Several calls in the past and service visits (at my cost) did not rectify the problem. Although there are many similar complaints on this machine regarding the loud noise and resulting problems during the spin cycle that involve the tub and rods, the representative said So sorry or Too bad we cannot not help you.My machine now does not run and is less than 4 years old --just like every other report. I get an error message F which the representative alluded to something involving the electronics. Machines purchased in 2004 from Whirlpool have across-the-board similar problems that Whirlpool refuses to take ownership for. This machine is their top of the line model. I dont feel the financial burden of repair or purchase of a new machine should be on the shoulders of the consumer. We bought in good faith from Whirlpool and expect Whirlpool to live up to their responsibilities. Thank you for any help you can provide.Rae **

Absolutely read the reviews on this machine before deciding on a purchase. I have experienced with great frustration every issue addressed in other reviews. Clothes constantly have to be rewashed. The Quick cycle will leave your clothes in a puddle of water. But then there is no spin only cycle to correct that. I have purchased Whirlpool washers before with great satisfaction but this machine is not worth the money I paid for it and does not save me on water or electricity costs because of all the rewashing I have to do. Like others I am stuck with this machine until it dies. You lost me as a customer, Whirlpool.

Whirlpool Duet Washer Trouble. Im having the same issue as Tom in Oakville. The F35-Sud errors pointed to the pressure sensor - NOT. 2 parts, a technician visit, and $800 later, Im still waiting on a Main Board replacement that is on nationwide back order. Time frame unknown.

Since there is only two people in this home, we decided to go for the smaller front-loading machine. This was purchased in 2012, still running. It does a clean wash, however common sense does remind people to not over-load a front load washer. If one follows directions, it gets the job done, and ones machine lasts longer without problems. Thanks.

We purchased our new Whirlpool Cabrio washer on November 1, 2013. From the start this machines performance has been a disappointment. We bought the machine at The Brick (I should have known better) where we had made several purchases over the years ( I guess Im a slow learner). Right off the hop, my wife and I noticed that the clothes were not coming out clean. Even though the machine is Eco and therefore advertises that it uses less water, there should be enough water that the clothes at least get evenly wet. That may be a problem with the agitator not seeming to have the guts required to pull the clothing down to the bottom of the drum. We went back to The Brick and told them that we were not happy with the machine they had sold us and quite predictably they told us that we should call Whirlpool (This was less than a week after we had it delivered. Did I mention that I may be a slow learner?). We called Whirlpool and they told us they would have a tech out to take a look at it on November 11th. Wow, I thought. Hows that for service. A repair guy coming out on a statutory holiday. Of course it didnt happen. When we called them back to ask if their repair guy had made it home okay, they claimed that we werent there when the repairman tried to call to confirm his arrival time at our home. We hadnt left the nest the entire day. They then told us to go back to The Brick. We went back once again and told them, yet again, that we were not satisfied. This time they agreed to send their own man over to take a look. He came over yesterday and watched the machine go through an entire wash cycle and then said that there really wasnt anything he could do, as even though it may do a crappy job of washing the clothes, it at least appeared that mechanically speaking there didnt seem to be anything wrong with it. We called Whirlpool back today and they said that there isnt anything wrong with it mechanically so from their end, at least, the story is over. What kind of customer service is that????? Maybe Whirlpool and The Brick deserve each other, but I think we should get better treatment than that

I purchased an extended warranty with my product purchase and only a year and a half into using this brand washer the lid broke on one side at the hinge, it looked really rusty and like others I thought I was making a very decent purchase because all of my previous appliances were Whirlpool so figured Id keep up with the brand. Sad to say that was the worst decision I could have ever made for 13/1400 dollars for a washer with a light inside. Never again. They wouldnt even keep up the warranty because they said it was too expensive to repair it. Whirlpool is very bad for business...

What is the brilliant idea of a mode dial on a washing machine that needs to be pushed in or pulled out to engage its function??? In other words, why is there a free-spin mode of THE DIAL itself? Okay. IN OTHER WORDS, why not just let the handle part of the dial stay affixed to the red line mark, so that they continuously turn together at ALL times???

Had the washer 3 years. After 1st year had to replace motherboard and lid locking mechanism. Beginning of year 3 the basket came loose, the machine wouldnt spin the water out of the clothes completely and then it quit cycling into the next cycle, ie, the tub filled up with water for the wash cycle but then would not begin agitating. The water sat in the tub until the wash cycle was done and then would drain but would not spin. Each cycle had to be manually started by pressing the pause button, raising the washer lid, and then pressing the pause button again. I called a repair person who ran a diagnostic on the machine and said it needed a new pump, new motherboard again and something else to make it spin properly. Sorry I dont remember what the something is. The estimate to repair was approximately $759 so I am now shopping for a new machine thats not a Whirlpool.

They contacted me to replace the washer. And the uninstall/install will be at my own cost. Its more generous than I expected. I thought they would send another technician and make everything go back and forth. This solution does save my time. I hope the new machine wont have all the series of issues.

I am getting numerous F1 codes on my Whirlpool Cabrio washing machine, Model #WTW6600SW2. By doing thorough research on this issue I can see the problem is in a known defective control board (part #W10130544). This part has even been replaced by Whirlpool with a new control board costing around $300 for just the part. After calling for repair service, two people (1 agent and 1 supervisor) refused to acknowledge any known issues with this part and further refused to any type of repair or replacement of the part. It is impossible for anyone in that position to not have knowledge of this problem. Simply look on the internet for a countless number of people with this very same complaint. Even though my washer is eight years old it has had very little use. There are only two grown adults in this household and the machine has never been abused or overused. It still looks new. Whirlpool should be honest and responsible when dealing with this type of problem. They should agree to pay for the part and repair service... at the very least they should agree to pay for the part.

We bought our Whirlpool Cabrio 7 years ago and it was great at first. I have not had any trouble with it ripping clothing. The clothes are clean. Its constantly breaking down. First it was the drain pump. Then the main computer board went! I called Whirlpool and of course the lady says its not covered. I had back up though. Google is amazing! I asked why this wasnt a recall as all over the web, people had this same problem. I pushed and pushed and she put me on hold. Came back to say it was in fact covered. What? Really? What changed your mind? She wasnt allowed to tell me. Supposedly had something to do with the date of manufacture. So okay, they send the repair guy out, its fixed. Now tonight, the lid locks and nothing happens! This repair was about 6 months ago. Grrrrr. Its been one thing after another with this hunk of expensive junk. When I buy an appliance I expect it to be problem free for far longer than this. I am not getting a code or anything, just dead air. So frustrating with three kids not being able to do laundry when I need it randomly :( Has anyone else had this problem? The lid locks, then does nothing. I unplugged it, pressed off and restarted it. Changed settings. Nothing is working.

We purchased this Whirlpool pair after our upright machine was unable to be repaired... because of parts coming from China and being hard, if not, impossible to get. We have had this pair for about 2 years now (Lowe’s). It still doesnt clean the clothes and it continually goes off balance when doing sheets, comforters etc. Myself I feel since they have taken the middle agitator out of the machine - it no longer performs the way a washer should and that its main function is to get the clothes clean! I did write a letter to Whirlpool about it and they pretty much told me, “Well too bad.” So much for buying American made products... at least the upright did last 6 years!

Whirlpool washer cabrio WTW7800X - Lid broke for the second time in less than a year. It is a defective part. Whirlpool should recall it. I will never buy Whirlpool again. The lid costs more than $200 + labor to replace.

My front load washer doesn’t get my clothes clean. I have to rinse twice and still there is soap in my towels and they smell bad. I’ve followed all the tips without much luck. Now I use only Oxyclean and rinse with 1/4-1/8 c vinegar. The machine doesn’t pump all of the water out of the machine either. To me it is low-efficiency!

The washer is only a couple of years old. It does the job but its not something wonderful or great. The previous one was a Kenmore but it was built by Whirlpool. It works. Thats all I can say about it.

As with other posts here, the rear bearing is going out of Whirlpool Duet front loading washer. I purchased mine in late 2008. Moderate use always according to recommendations. I called Whirlpool and same story--no recall and it would be expensive to have it repaired. I cant see putting $400 to $500 in parts even if I repair it myself. I cant believe that with such a common problem, Whirlpool wouldnt either honor a repair or offer a reasonable bearing package to fix. It requires the entire back, half of a new drum. Poor design, but whats worse is no effort by Whirlpool to rectify the situation.

I bought this washer because we are a family of 6 that washed a lot of laundry. I bought the extended warranty from Lowes but not sure if this thing can even be fixed. The guy has been out twice. Replaced the control panel. I cannot wash more than 3 towels or it comes unbalanced and goes crazy. I need this fixed. I am so irritated. A recall needs to happen.

Whirlpool washing machine model WCW4950XW2 - We have a barely two year washing machine that we purchased at Best Buy and it no longer drains or spins. After $100 repair call we were told that this is a common problem with this model. It is a transmission problem, and with the way the machine is built a repair person cannot get into the transmission to fix it. He suggested we buy a new washing machine. This is a travesty on so many levels! If whirlpool know it has a problem it should offer a partial refund for the purchase of a newer better machine. I keep thinking about what our landfill in this world look like with the proliferation of appliances that are engineered to last a year or two. I can guarantee you I will never purchase any Whirlpool produce again, and I will research whether other brands are associated with the whirlpool brand before I buy it. Sad that a once good company has gone to hell.

Whirlpool duet - This washing machine is absolutely horrible!!! I pull clothes out and they are tore up! We have replaced parts that we were told could be causing the damage and its the same thing! I am very unhappy! Ill be calling Whirlpool again but Ill probably get the same runaround - oh we are very sorry we dont have any known issues with that machine. Clearly when you look online it is a very known issue!! I doubt all of these people lied about calling!!

We spent a lot of time researching to make sure we were making the right choice, found the one that was right for us. When it got delivered there was a problem though, the plastic scratch protector film they put on the doors for delivery left an adhesive residue that looked like dull spots all over our new shiny black doors. I immediately opened up the owners manual to see how they recommend removing this blotchy sticky residue, assuming we werent the first ones to ever come across this problem, unfortunately they only provide generic cleaning tips. So I went to their website and found what I was looking for. I tried all of the cleaning methods they provide, none of them even came close to working. So I grabbed some adhesive remover and tried that, it worked great to remove the residue however my microfiber cloth (which they recommend explicitly) started leaving scratches all over the finish.I called the customer service to see about getting a new door delivered, thinking this wont be more than a 5 minute phone call since I had followed all of their steps they provide both in the owners manual and on their website. Heres where I find out that their policy DOES NOT cover scratches/cosmetic damage, period. I tried reasoning with them, I had them read their own recommended cleaning procedures, and we both concluded that I had followed their procedures to the T! You might think that if the all of the typical procedures didnt resolve the issue, that would be the point where the customer service reps would have the ability to make a decision that satisfy the customer, you would be wrong! They kept telling me over and over that their policy doesnt cover cosmetic, therefore there was nothing they could do. It was delivered with a defect of sorts, how is the customer responsible for that? The only way I can see it having worked out in my favor is if I had never tried to clean it myself and immediately called customer service, I still fear they would have given me the same line of cosmetic damages are not covered even if I would have tried each procedure with them walking me thru it over the phone. Lesson learned, I will never purchase another Whirlpool product!

The Whirlpool engineers need to go back to design room sober on this machine. It is only a year old and still I have to run one load two sometimes three times just to get clothes clean. How is this energy-efficient? I have tried all of their so-called remedies. Paying such good money for a lousy and lazy appliance is hard to swallow!

I bought a HD Whirlpool in April 2011 and I hate the machine. It does not use enough water to wash clothes. I open the lid every wash and cannot believe Whirlpool can label this as a washing machine; it spits a little water now and then. I am demanding Lowes and Whirlpool to replace the washer. I have used two Kenmore washer for 45 years and I never had any problems. I use hot water to kill germs -- well there is not enough water to drown a fly. How can these manufacturers sell such product and then give the consumer such a hard time when they ask for help. Dark clothes have white residue stuff all over them. I have to hand-wash a lot of my clothes. I have never in 45 years had to do this. I am so mad that Whirlpool is taking everyone for suckers. Now I am sure that there are a lot of people who just never take the time to complain; too much trouble and just go buy another brand of machine. We consumers need to demand that manufacturers sell quality products.

I purchased a Whirlpool Cabrio washing machine April 2016. I was so excited to have a new washing machine. I thought the 1st couple times I used it I just didnt have settings right. It uses so little water it doesnt get all clothes wet. If they are not wet they cant be clean. So I started doing very small loads. Then clothes were not clean. They stink. So I have tried every detergent out there. Nothing helps. Another thing it takes an hour or longer per wash to get not so dirty clothes. Not to mention it puts holes in my towels. I tried reaching out to Lowes where we bought it only less than 4 months ago only to be told they would contact Whirlpool. Whirlpool wanted to send tech that I would have to pay for just to tell me that the piece of crap washing machine is doing everything the manufacturer made it to do. I told him I was not going to pay so. I think with all the problems people there should be a class action lawsuit. DO NOT BUY CABRIO!!!

Cabrio top loading washer - I have had this set for 3 years. The first 8 months it was fine, then came all the rust. I had to go to the BBB and file a complaint as everyone at Whirlpool would not help. Last year they finally replaced the top, and now, its rust yet again. I rinse and dry the machine when I am done using it. The repair man said it was because manufacturers are not using primer and just one coat of cheap paint. What now? Ill see if I can get the lid off and sand it and use rust preventer on it. Never again, I should just junk this piece of crap and Whirlpool should shut down if they cant make anything worth our hard earned money.

We bought our Whirlpool Cabrio Platinum top-loading high efficiency machine Model #WTW8000BWG in Feb. 2015. It cleans well, and is easy to select water temp, spin speed, etc. It's simple to load, but because I am short, I have difficulty reaching stuff at the bottom of the tub. A stool is needed. LOL. In the 5 years that I have owned it, I have not needed any kind of service to be done on it. Very reliable. I have had Whirlpool washers and dryers before and my success with them is why I purchased the set I have now. And so far, so good. Highly recommend.

We purchased it from Best Buy. It was a good thing we got the extended warranty. They completely rebuilt it two times. In the 6 years we have had the washer. The motherboard went out. The bearings went out. The only thing nice I can say is that it’s a top loader and doesn’t get smelly like the front loaders do.

My husband and I, purchased this washer on November last year, I used twice before and I noticed that the clothes felt hot, but the cycle was COLD water. Now use it again until June 2015. In every cycle the clothes were hot, I started calling to get an appointment in June at the 1800-253-1301, but the system was down twice. Then in July then again the system was down, then August 10, system was down. I did not wait more and called back the next day, August 11, got appointment for the 20. A technician came, he told me that the hoses was switched, but I know the hoses was installed correctly, my husband was here at the installation. He knows the proper installation of the washers.