Weve had this washing machine only a few years, and our household of 2 probably averages 1 load of laundry per week. Weve always had the same problem everyone has with the detergent stains on clothing and having to rewash loads, and the only remedy weve found was using the oversized loads setting and rewashing a load. The last straw was 6 months ago. It quit going through a complete cycle and would not spin out without resetting it. Then it quit spinning out at all. Service Guard, a 3rd party warranty company, diagnosed a faulty motor and ordered a replacement. After a long delay Whirlpool advised it was back-ordered for 3 months. A week ago Whirlpool advised them it was now back-ordered until 5-27. They did not know whether wed ever obtain a replacement motor. After taking clothes to our sons house for a couple months to wash, we purchased another used machine to use until ours is repaired. It is beginning to appear that machine may be our permanent machine. This is a pretty sad testimonial about whirlpool. We have always used Whirlpool appliances but appears we may have to switch brands. And it certainly does appear these low water machines are garbage. Very disappointed in Whirlpool.

My husband and I purchased a Whirlpool Washing Machine & Dryer a year and a half ago. As of current, the machine has stopped working. The machine will turn on but will not agitate. It makes a horrible grinding noise. The type of washer we purchased was a WTW4900BW0. Whirlpool told us we should have purchased the extended warranty. But, I feel we should get more than a year and a half out of a machine that cost $650.

Bought this model #WTW8500DC from Lowes in 2015. Ever since had problems. Stopping in the middle, not starting, recently keeps running water, lid lock issues, had multiple service calls and multiple hardware changes, paid extra for extended warranty from Whirlpool hoping that within a year all problems would be gone after so many repairs. Boys I was wrong. After spending around $1200 between this machine and the extended warranty, three year later after the warranty expired now I am stuck with this non-functional piece of junk and looking for another washing machine. Would love to hear from Whirlpool if I stumbled upon a lemon, or three year is expected life of their $1000 plus machines.

I purchased the Whirlpool Duet Steam Washer and Dryer in the spring of 2010. Washer bearings just broke. I was told that the bearings in these machines are not strong enough to support the spin cycles. It is very disappointing to think that a company like Whirlpool would have their customers pay $1000 for a machine they know is not going to last. I agree with Julie. Maybe a class action lawsuit needs to be filed. Is there a lemon law for washing machines?

Whirlpool Cabrio washer - Do not buy this washer. I have never placed a comment on the web before, but after reading about the same problems over and over, there should be a class action suit. The spin cycle will not balance. You have to stand over the washer and readjust the laundry. I called Whirlpool and I was told to unplug unit for 5 mins. This is a $800 washer that lasted about 2 years.

This Whirlpool Cabrio washing machine just does not do the job. It smells inside and does not get clothes clean, just normal everyday laundry. I usually have to put them through twice. It is supposed to be a water save, but I dont think it uses enough. I use minimal he detergent, yet you can see detergent residue on the clothes after they are washed, I think because there is not enough water running through to rinse clothes very well.

We purchased a Whirlpool Duet front load washing machine Model #WFW9550WL in July 2009. In July 2016, the guide on the door hinge broke, making the machine unusable. When performing a national search for the part number (#8183202) to replace the broken hinge, I found that there were none available anywhere in the United States. When talking to Whirlpool, they indicated that during 2015, they only sold 142 of this part, and were currently looking for a new manufacturer for the part. They further indicated that the part would not be available until late September or early October of this year.

The Whirlpool duet front loading washing machine came with our new house five years ago. That machine has destroyed multiple clothing items including very expensive sweaters and undergarments. It has destroyed biking shorts and just about anything of value. Even destroyed the bags fur delicate clothing. I have to get a repair guy out every year to replace the bellow too! It is terrible!!!

We owned a Whirlpool Duet washer that went out in late December 2011. We bought another Whirlpool Duet washer on January 8, 2012. On July 31, 2012, it stopped working with the error message F24. In WV, Whirlpool contracts their insurance/warranty through ACE Appliance. We scheduled with ACE the next day. They came out on August 6, 2012. The repairman told me it would be 7-10 days for the part. The part was on back-order, so in reality it took 17 days before they returned. It was repaired on August 23, 2012. Today, September 17, 2012, the washer stopped working again with the same error: F24. Whirlpool will do nothing to replace the washer, even though it is less than a year old and we paid $900 for the washer. This is the second Whirlpool we have owned that has crashed. I have two small children (4 and 2) and I am due with number 3 in 3 weeks. While the washer was broken, I spent nearly $80 at the laundromat for washing only - I carried baskets of wet laundry home to dry. And now I get to repeat the same exact struggle less than a month after it was fixed. When asked, the customer service rep told me that no matter how many times it broke, all they would do is send a repairman. They never ever replace appliances regardless of the problem. I am unbelievably frustrated and I want to tell everyone that I possibly can to stay away from Whirlpool appliances! Do not buy them new! Their manufacturers warranty is a joke!

Two-year old Whirlpool Cabrio top load washer; absolute piece of junk! Bearing on the drum howls like a train. Now the master board or some other sensor (under drum) is out. Serviced for the third time and the service repairman states its cheaper to replace than to repair. For a 2 person household, it is reasonable for us to expect more than 2 years from a washing machine. Same experience with Whirlpool 15 years ago. 1st time shame on you; second time shame on me.

I bought my washer machine because my other one died on me. I was nearly everyday so I needed a dependable machine but also good price. This machine is both and I would definitely recommend Whirlpool.

I purchased this washing machine December 16, 2011. I paid $737.07 for this machine. 14 months later I had to repair the top of it which cost me $255 for the lid which the plastic around the lid was cracked. I had to pay $136 installation fee and two years later the exact same thing happened again, the plastic cracked. I have contacted Whirlpool which took a complaint - said that was all they could do. Ive contacted the store where I purchased it, they can do nothing. I read online there are many complaints about the lid on this washing machine. It shouldve been a recall. I will never purchase a Whirlpool product again. I will not pay to have it repaired again. I will give it away and purchase something else not whirlpool and not from Lowes. I expected some kind of compensation from whirlpool on this. I have all my receipts.

I purchased a Whirlpool washer in March 2007. That washer is now leaking from the bottom. I called Whirlpool. I was told that the machine only had a one-year warranty, so repairs would be at my expense. The CSR then offered to schedule a service call for me at $139, which I refused. A few weeks later, I received in the mail an offer for an extended warranty on my Whirlpool washer.

Does not clean clothes as well as I was told it would. Very dissatisfied with the price and performance and would not recommend this brand to family members as well as friends. With the way the current economy is, companies like Whirlpool should reduce their prices!

I have had a lot of washing machines in my life and trusted that Whirlpool would have good products. Well, with this top-loader, I couldnt be more wrong! I have never had a machine that just sloshes clothes around - at best - leaving them just as dirty! Our water bill has greatly increased on top of that - I AM SO VERY DISAPPOINTED! Unfortunately I cant return the bad merchandise since I bought at a Scratch and Dent store (just a dent on the outside does not interfere with performance...).

They are good washers but they are overpriced. They have way too many functions for doing laundry. I know everyone wants their washer to do it all but the machines just can’t. There is no washing machine in the world that can sense a stain and pinpoint it and remove it.

I was not impressed with the new HE washers but could not find any traditional ones anymore. I bought a Amana and am disgusted that it is only 3 years old and needs to be replaced because of a transmission problem with it not agitating. It costs more to repair than it is worth. As a consumer, I should be given a choice whether I want to upscale or be satisfied with older model features. I will never buy or recommend a Amana HE washer to anyone. My mother also has one, has had it for a year and it is already giving her problems. Shame on you Whirlpool.

The washer can not spin dry, as the unit will not balance. When it spins, it will get out of balance, and shuts off. I have had a repairman out, but he said he can not fix it, and that this is common with your units, He suggested we get a new one, but not from Whirlpool.

What a horrible experience. I purchased a Whirlpool Duet HE Front Loading Steam Washer in 9/9. I have used it no more than 15 times. It has an error code F70. I called Whirlpool and used one of their recommended technicians. He was there for no more than five minutes and he informed me that it was one of the two parts--one is $300, the other is $500. Both these parts are computer chips. He instructed me to call Whirlpool stating that they would give me the parts for free. I did, and they refused stating that the product is now out of the one-year warranty. This is clearly defective. I am now faced with $1,000 fix. I feel that I was further misled by Whirlpool because they should have told me before the service call that I was going to have to pay $1,000. The customer service reps and the manager were both unresponsive and rude.

Installers left and Home Depot Cabrio washer stopped with water left in tub. I reset GFIC outlet, tried again and it stopped. Did some research and tried different outlets. Same result. I discovered that if you shut off machine as soon as the GFIC is reset, then the washer will drain no matter what. I have been on the phone with Home Depot and they have no solution but to wait one week for a repairman. Very dissatisfying service. Now I am running a 20 foot, 3 prong, heavy duty extension cord into living area where there are no GFIC outlets and it has been running. I believe there is a fault in the washer, but they must not care if we get electrocuted from the faulty grounding of their Whirlpool product.

All of sudden without any notice there was such a clatter. We dashed downstairs to see what was the matter. My washer Cabrio was on its side off balance. I hollered what is the matter. We sit it up, see the back side bulge out and with some searching we discovered the balance thingy was broke. Now I bought April 2012 while going through Chemo May 2014. I burying my washing. Call Whirlpool. Well they say I file this away sorry about your luck - lol. Do not buy this washer unless you want another one in two years junk and they will not help. Well they will if you give them more. The 1400 dollars I already gave them for the set is not enough.

Whirlpool has been a trusted name for us for many years. The large tub has cut my wash load in half. Large towels to delicates have never been a problem. My washer is going on 12 yrs old and runs like a champ.

My old 25 yr old Whirlpool died and was shopping for a new one. I saw the Cabrio and was really impressed by the features and large capacity interior. I can say that I thought my clothes were getting clean until I looked closely. I have never been so disappointed with this washer. I wish I had my old one back! Clothes arent clean, they are so twisted when I take them out and theres a horrible smell, like oil burning when it runs. The machine would fill up and when it would start to wash, it wouldnt, it would stop. And a loud humming noise was coming from the back.I shut it off and turned it back on and it wouldnt clear. I had to unplug it and plug it back in to clear it and start over. The bearings are gone now and I was going to have a repairman come and look at it, but now I wont bother! After reading everyones comments this Cabrio is a piece of junk and Im sorry I ever bought it! So now Ill be shopping for a new one tomorrow with an agitator!!! Im not impressed with the HE appliances!!! Ive owned this POS for not quite 6 yrs. Expensive to purchase and I will not recommend Whirlpool to anyone! Its sad that companies today make cheap products!! Built to last... ha!! Well never see those again!!

Cabrio washer lid warps twist and cracks the frame. Not a proper lid design apparently.

Whirlpool Cabrio Platinum Washer - I have a 2 1/2 year old washer that has been serviced twice. This week 10/2/14 the service technician informed me that we had a bad tub bearing. The bearing failure caused a leak which corroded the rotor & stator. It was more cost effective to buy a new washer than to repair our unit!!!! Ive never heard of a washing machine needing to be totally replaced after 2 1/2 years. Any ideas how to deal with Whirlpool?

When we bought our house the Matching set of Whirlpool Cabrio Platinums came with it as they were new. I decided to keep them and sell my LG Troms.Absolutely the worst mistake was keeping these Whirlpools. Who in their right mind would consider a washer with no agitator a washing machine? The clothes just sit and do nothing. They don’t get clean at all. Its a complete pile of useless junk and the person or persons who engineered it shouldn’t even be in charge of designing birdhouses.Whirlpool themselves should be ashamed to put out such a pile of garbage to the consumer. Our house came with all new Whirlpool appliances and we are going to replace them all and never give Whirlpool a look again. Whatever you do don’t fall for the shiny unit, slick salesmen. Because all youre going to get with Whirlpools washer is all talk and zero action. Thanks for the not so clean clothes Whirlpool. The local laundry mat thanks you when I need to actually clean my clothes.

We purchased 2 whirlpool commercial coin operated washer machines and both computer boards had to be replaced twice each - model CAE2743bqo and CAE27438qd.

Ive had so many problems with this washer. Everything has been replaced on the machine and it is still a failure! It has overflowed 5+ times. Stopped draining 4 times (fun getting water out of it...). Have been without a washer for a total of two months! My In-Laws have the same and theirs hasnt been a problem (however it isnt used as much as mine.). Hopefully mine is just a Lemon! Ill never buy another one!!!!! Especially from Lowes. They deem it only a lemon if it has had the same issue for 4-5 times. That is with the extended warranty! TO THE DUMP IT GOES!

We relied on consumer reports as the primary source for a recommendation on this washer. Just under two years old, it started making a noise, which suddenly went away. Then one day the machine would not spin and drain, and we could not decipher the error code into anything useful. I turned the machine over to find that the drive belt was half-on/half off the pulley on the drive motor. This caused the belt to ride against the belt guard and wear right through it. I removed the belt and determined that the cause of the problem was that the large pulley on the drum was loose. For some reason the nut which holds that pulley on was slightly loose, causing the pulley to wobble. Not sure why they didnt use some Loctite on that nut. I put everything back together and tightened the nut. No problems and I checked it a month later, everything was still good. Fast forward to last week, when the machine was not yet 3 years old. Same thing, washer would not spin and drain. Tipped machine over to find that the belt had fallen off, the drum pulley was again loose. But this time the belt had damaged the pulley on the motor. I figured, no problem, just order a new pulley. Well you can buy just the pulley on the drum, but the pulley on the motor is part of the motor, it cannot be ordered by itself. The cheapest I could find the motor online was $250. We decided to cut our losses and buy a new machine. We will NEVER buy another Whirlpool appliance (or anyone elses by the same manufacturer, i.e. Maytag). Our last Kenmore washer lasted 23 years. Oh but it had an agitator and wasnt listed as HE (High Efficiency), so I suppose the environmentalists would get the dry heaves thinking about the impact of that washer on the environment. But it was useful for 23 years. Now this High Efficiency Whirlpool is headed for the recycling pile. Sorry, I think this hurts the environment more than an appliance which just works year after year. Yep, they took a design that worked and now we have energy/water efficient washers that dont last very long and are so expensive to repair that the solution is to just buy a new one.

Purchased this washer 5 months ago. Have had service 3 times as dark clothes come out with white residue. I have done everything possible to correct the problem. They recommended from cleaning the machine, using less detergent, minimizing the load, using extra rinse, deep water and still the clothes come out with the residue. And it takes way too long to wash a batch of clothes. This is a known problem with this model. Repair company recommended a replacement and Whirlpool insists that it is a usage problem. One thing they said Could be water is too cold, I live in Florida there is no cold water! Whirlpool refuses to replace it. DONT BUY IT!!!

We bought our Duet washer in 2007 with a three-year warranty. In 2010, the washer started banging so we called it in for repair. It was determined that the bearing on the drum was bad, so the entire drum assembly was replaced because the poor design of integrating the bearing into the drum. Almost one year to the day, our washer started banging again. The washer is no longer under warranty. We were told the parts are around $400 plus and another $400 for labor.The repairman was from the store we bought the washer and he is a certified Whirlpool repairman. He related to us that this is a very common occurrence for Whirlpool washers because they are using cheap foreign made bearings. He services this problem on a weekly basis and Whirlpool will not do a recall because unless it is a safety hazard, it is not a concern to them if consumers have to pay out the nose for cheaply made parts. This repairman informed us that during training at a Whirlpool class, he learned that on the main board of the washers, they could put a 2 cent lamp that would indicate a bad board which would simplify diagnosis, expedite repair and reduce service time, but Whirlpool wont do it because it isnt cost effective. The repairman told us that we can call customer service until we are blue in the face, but Whirlpool wont give a ** because it is out of warranty. He sees this happen all the time with Whirlpool. My wife called Whirlpool Customer Service just to be told we are ** even though the cheap, crappy bearing that went bad was done under warranty, a year earlier.Well Whirlpool, I guess you lost another customer who will make sure that you lose a lot more customers. We are going to take our business elsewhere and we will make sure all our family, friends, neighbors and coworkers know how bad your customer service and poor attitude is toward consumers. If you cant back your products when you put cheap foreign garbage parts in your product, then you need to lose business and get out of the market.

WTW5640X The machine is tearing up clothes of many including mine. I gave them the benefit of the doubt and thought I had over-loaded the machine. Not so. There has been nothing run through the machine other than clothes and bedding. When I called for service 1 1/2 months after warranty is out of date I am told I can have a service call including parts and labor and another year warranty for almost $400. If it werent for the numerous reports online of the machine doing the same to others I might have gone for it. Shame on you Whirlpool. Are you the next GM?

Bought this washer 3 months ago. Absolutely hate it! Leaves white film on my clothes. Have to run all washes through a quick wash to get the film off. Hammers the water through the pipes, causing the fittings to come lose and leak! The spin cycle practically dries the clothes leaving them so wrinkled that I have to dry them longer to get the wrinkles out. Waste of my time and MONEY!

This company has terrible, deceitful, and pass the buck practices. I purchased a Bravos MCT top loading Maytag washer from Home Depot. Maytag is now owned by or has been acquired by Whirlpool. First I was a little disappointed to learn that because I had previously purchased two Whirlpool made washers and got no more than six years of service out of both them. But from the day this washer was delivered it did not perform as it should. I called and texted with the hours provided for rejection of the washer and was told by a customer service representative that it would be replaced. The main problem was the spin cycle. With only a few clothes in it, it jumped all around and moved so much that it was sitting in the middle of the washroom. Thinking that occurrence was a one time thing, I stopped it; cancelled the cycle; and reset it. It finished the load. This occurrence was reported and simply fell on deaf ears. I was lied to and told a replacement would be made; it was not. I have sent numerous emails and have made several calls for more than a year now and I still have the same defective washer in my home. Each time I emailed, I received a different message from the customer service person. This company wants me to pay for a service call or buy an additional warranty for a defective machine they produced and refuse to honor their replacement policy— which they now say is the responsibility of Home Depot. Luckily I have kept every email and document I was provided. I am being forced to file a claim against this company to get their attention and to remedy this situation. The expense of the claim will be greater the cost of purchasing another machine, but it is this kind of behavior, on the part of A corporate giant, that is makes life tough for everyday people like me. Stay away from the Whirlpool name for washers—even a prior good name brand like Maytag.

On its 1st year, the water pump went out. It cost $200.00 to replace it. On its 2nd year, the circuit board went out, and it took $300.00+ to replace it. On its 5th year, the bearings went out and cost $250.00 to replace it. I bought this for $900.00, and I already have paid $750.00 plus the price of purchase which makes this washer $1,600.00. Whirlpool should compensate all of us who have worked hard and have purchased this product! I will never purchase from Whirlpool again. I can’t afford them. I should get a refund from Whirlpool. Don’t they care? Email me for these problems at **. I am so dissatisfied with this product.

I owned a Whirlpool Cabrio washing machine for 3 years (a two person household). The repairman just quoted $700 to repair a faulty center hub seal and bearing. This machine was not inexpensive. I expect more from a quality machine. A telephone call to Whirlpool resulted in two ten minute holds while being shuffled between representatives and each representative tried to sell me an extended warranty for another $289. Whirlpool should take full responsibility for this faulty product and not act like a telephone support center located in Eastern Europe. I am not pleased with this (lack of) resolution and do not plan to purchase another Whirlpool product.

We live in Hawaii, so the price for our stacking closet size unit was exorbitant. It was over $1,000.00. It is small so the size of loads are small too. We bought one that is supposed to sense the load size and deliver the correct amount of water. It does NOT do this. Reviews online show complaints of this same nature. It does clean well but we have to do very small loads to get that.

Dryer panel broke washer. The smell is so gross I will need to throw it out. I used only HE detergent.

I have had this Whirlpool Cabrio washer for 4 years. I had to rebuild the drive unit once and now the control board is bad. If I didnt do my own repairs I would have spent well over the cost of the washer in the 4 years I have owned it. This is the worst washer on the market. Not to mention Whirlpool support will not work with you at all. DO NOT BUY THIS PRODUCT.

Purchased this washer 7 months ago. We are a family of 5 with A LOT OF LAUNDRY!!! I adequately researched a machine that could do large loads of laundry, WELL. I read at least 100 reviews and went forth. (Note to self that anyone giving this machine a decent rating, is a DIRTY, SMELLY, FILTHY LINEN WEARING FOOL who doesnt take much pride in their clothing cleanliness.) I proceeded onward and after paying A LOT OF MONEY for this 4.8 Whirlpool Cabrio Washer, I found out within the first two days of owning it, that IT IS GARBAGE! Regardless of the 4.8 drum size, you can only fill it less than 1/4 of the way with clothes, to even hope they will be touched by water. My clothes come out DETERGENT STAINED & DRY! Insanity... A washer that doesnt wet the clothes!!! We have had 4 repairmen come out within this time, because I am fed up! I have been physically shown and told now, by all 4 guys, that the washer will not fill more than 9 inches with water. They advised me to fill Home Depot buckets and throw them into the drum. THIS IS WHAT I DO, TO SATISFY THAT I AM WETTING MY LAUNDRY - PURE CRAZINESS! The repairmen told me to set all loads to bulky sheets + extra rinse + highest soil. This is a 1 hour, 26 minute initial setting. Note that my adding water messes up the computer readings and it will reset throughout the washing cycle multiple times. Even with all of this... the machine still doesnt wet the clothes!! The top and center of the load is BONE DRY! This machine will not wash sheets, blankets or comforters, either. Dont waste your time trying!!! Dont be fooled by the drum size. Your great grandmothers 1930s 1.6 cu ft washer washed more clothes in any given load. #1 My water bill is through the roof. #2 The washer constantly resets and runs on any single load for over 2.5 hours AND #3 MY LAUNDRY PILES HIGHER AND HIGHER, as you cannot put more than a smattering of clothes in the machine, at any given time! GARBAGE, GARBAGE and MORE GARBAGE!!! I would be better served to find a stream and a flat rock and start doing my laundry colonial day style! I am done... Finally had enough of this insanity! RETURNED THE MACHINE THIS MORNING!!!

We purchased the extended warranty (service plan number **). The washing machine has been giving trouble. It locks out during every wash cycle and each time, we have to unplug the machine to reset it. Sometimes it makes it through the next cycle and sometimes, not. The first couple of calls we made, we were told to make sure it was cleaned, to make sure it was leveled. All this was done and we still have the same problem. Finally, a technician was sent out. He could not duplicate the problem and left. Thirty minutes after he left, the machine locked out again. We put in for another call, we were told it would be two more days. In the meantime, we actually video taped the next three times it locked up. This time, when the technician came out, he was able to see our video as well as saw the machine lock up. He stated, It did not give me a code so I do not know what else to do. He left and ten minutes after he left, it locked out again. We immediately called back and they informed us they could not get anyone out again until next week. This is very frustrating to have an obvious problem and have an extended warranty and the problem cannot be solved. We feel as if we are being blown off. Is there anything you can do to help us and/or give us advise of how to get this problem resolved?

I had my washing machine for about 10 days before it stopped working. I did about 4 loads of laundry. We have had 3 repair people come check it out, all referred by Whirlpool. They each had a different theory on why it wasnt working properly. Im now waiting for parts to be delivered and then service to be scheduled. When I contacted customer service, I was told (after waiting on hold for about 1 hour) that it was customer misuse. Ahem, first I heard that, and I think I know how to use a washing machine. I asked to speak with a supervisor. More waiting. Tina (#**) told me she will contact the service company about the parts. I told her to please conference me in on the call because I want to hear the outcome (and I dont want to wait another 1+ hour to reach customer service again). She put me on hold and then disconnected me! Really, all this time and 3 service people... Would be cheaper to just replace the machine altogether. What a headache!

In 2011 we bought a Whirlpool Washer (WTW4950XW). We had a one year warranty. There have been problems ever since we bought it. Of course it is no longer under warranty. In the last few months we have encountered brown spots on clothing. The washer has always spent an inordinate amount of time Scanning. It does not matter how much I readjust the load. I ALWAYS must do an extra Spin and Drain. Sometimes Rinse and Drain helps...sometimes not. Sometimes the machine indicates it MIGHT be finished washing but only the clothing on the bottom of the load is damp. It does not rinse the soap out. Recently when I washed my husbands coat several times -- he had to finally hang it in the shower when he bathed to get the soap out.We had repairmen out once when we had the warranty. They said the drainage hose was wrong. We adjusted that. I called Whirlpool more than once about our problems. They said they could not help because we had no warranty. OK. One young lady said we could get a 5 year warranty for $353. For $499 we might get a machine without all the 747 dials and tweets and fewer government, EPA amenities. Whats wrong with this picture? My old washer lasted 30 years. We are very, very sorry we did not repair it. All I want is a washer that will provide me with clean clothing, towels, sheets and blankets in a timely manner. That does not seem to me to be too much to expect. I am considering a washboard! Or the shower for ALL my laundry! I am angry and frustrated. I always considered Whirlpool a good brand.

I bought a Whirlpool washer and after a few months it started acting up when spinning. I contacted your so called customer service and they gave me the runaround. Told me I wasnt loading it right. Im 60, I know how to load a washer. Well it got worse and worse and finally went kaput. Its going to cost over $100 to fix the springs and I was told it was your lemon and all that brand was bad. I will never buy another Whirlpool product because you wont stand behind them....

I like the newer technology that is built into the washer. My only complaint is that the wash time is automatically set depending on your load choice. For instance, a delicate load is set to wash for 45 minutes. I dont feel that amount of time is required.

Cabrio he washer wtw6400sw2 - I bought this washer about 6 years ago at the time we paid around $900. Now my bearings went bad and the repair person told me it would cost around $300 to $400 to replace the bearings and seal and shaft but that I should call Whirlpool and see if they could replace the part or give me some discount cause it is becoming an issue with all the Cabrio washers. So I called and spoke with a so called manager - as far as I know it could of been a cleaning person there. She told me that she could not do nothing about the issue. So if a lawyer would be nice to help me and the rest of the world that are having all these issues to file a suit against Whirlpool Corp.

CABRIO GETS A ZERO RATING. We are sorry we ever bought this washer in 08. The unit had a defective main control board and was replaced in 2012. The factory authorized service agent from A&E literally robbed us of jewelry while in our home. Now the main electronic control board needs to be replaced again. Neither Whirlpool or their authorized agents are truly customer service oriented on the defective product. Neither are willing to make an honest attempt at regaining our trust. I have contacted both and neither will acknowledge or offer reconciliation. The problem with the main board and the recurrent F-50 error has been denied by Whirlpool although acknowledged in numerous consumer forums as this. Our family is now without a wash machine. We have not even received a simple apology for the theft from the service agency - even though their employee has been arrested. BEWARE!

I thank the folks at Whirlpool for building a washer (Cabrio tub bearing failure) that lasted 22 days just shy of four years, better than the Whirlpool Duet that lasted 14 months, tub bearing failure also. Now I have high confidence that Whirlpool pre-engineers failure into every washer they build.

Havent had any issues with it. Works great but does end up off balanced quite easily and halfway across the garage. Washes clothes like a maid. Is kinda small for bedding.

Everything comes out clean and it doesn’t cause items to be tangled around each other. It has a setting for every possible type of load. I especially like the option of having “deep water”. Not having a “glass” lid is a plus.

In the past 8 years, I have had to replace 2 Whirlpool Calypso washing machines and 1 Cabrio washing machine. All 3 washing machines worked great for the first 2 years. I purchased the Whirlpool extended warranty on all 3 washers. The first Calypso had 12 repairs done on it. Finally A&E repair service deemed the washer not repairable. Whirlpool replaced the Calypso with a new Calypso. Based on the problems with the first one, I again, purchased the extended warranty. Again, after the manufacturers warranty expired, I again had issues. After numerous repairs, A&E deemed the washer unrepairable. I contacted Whirpool warranty service and was told that they would reimburse me 75% of the cost of their choice of a Whirlpool washer! Since I have had 10 hand surgeries, I need a washer that does not have an agitator (hence the original Calypso purchase). The model that Whirpool warranty deemed as a replacement had an agitator and was also a much lower energy efficiency rating. I found that the Cabrio was a comparable replacement model and finally Whirlpool agreed to replace the washer at 75%. I was angry that they didnt cover the total replacement, but felt at least I got a totally new problem-free washer. I again purchased the extended warranty. I got the Cabrio in March of 2008. In April of 2011, the washer started getting rust around the bleach dispenser and also I would get UL code (Uneven Load). A&E tech came out and replaced a bearing. He said that the rust was not covered under the warranty. I asked how it was okay to have rust around the bleach dispenser if the washing machine is always wet with water. A month later, I was still having a UL code and the rust was getting worse. A&E came out again and said that even though I saw rust around the bleach dispenser, the rust was in fact underneath the tub and had eaten away at the parts. He called the warranty company to authorize repairs and the Whirlpool warranty company denied any more repairs on the washing machine.

I purchased this washer over 8 years ago and we have been using it 3 to 4 times a week/ 52 weeks a year since. It has performed flawlessly up until about a year ago when it kept given me uL error. Everytime I wash the basket always spins wobbly and unbalanced it seems. I checked the Internet and it turns out others have had the same problem. The solution was to replaced the 4 springs supporting basket and that fixed the problem. Been working ever since.

I purchased a Whirlpool front loader as well as an extended warranty. The machine worked well for about a year and a half until i noticed rust patches beginning to form on the front of the machine. We contacted the retailer that we purchased it from and they suggested that we call the people that we had bought the warranty from. Unfortunately, the warranty does not cover rust, so we have to wait for it to rust out and just buy another one. It is only 2 and a half years old and is totally rusted across the front of the machine! It is extremely unsightly. This is the second Whirlpool washer that we have bought and the second one to rust out on us. I would never buy another Whirlpool appliance, and extended warranties are not worth the paper they are written on, let alone the amount that you pay for them!

Just bought the Whirlpool 3.5 cu ft, Top Load HE washer (model WTW4815EW), but of course, the sales person did not explain that HE meant LOW WATER USAGE. Wish I had done my homework. FIRST LOAD, clothes seem to be beaten to death, and must pour in detergent before you load clothes. So, Oxyclean detergent I always used in my regular (NOT HE) washer put a hole in one towel and discolored (faded out) the others. Also seems that the fast and hard agitator would not (logically) last very long. It seems to be working very hard. Im SO disappointed. Called Whirlpool to say I dont like it. They said to call Home Depot and see what they will do about an exchange. When I did, my sales person said that almost all the washers he sells are HE. I want the old type washer back that allows me to add more water if I want, change the cycle and water levels at my discretion, add detergent when I want to, and soak clothes if I wish.

Im on Whirlpool Cabrio washer top number 4. Well over $300.00 each, and washer doesnt work with a broken top. I sent a letter to Whirlpool telling them, NEVER again Whirlpool and my reason is the 4th top in 6 years. I received a form letter back... apologizing for a delay in response and, we hope you enjoy the rest of your day, lol. They dont get my level of dissatisfaction or better just dont care. Never again Whirlpool.If you search Cabrio Washer tops you can see thousands of dissatisfied customers... and still Whirlpool has the arrogance to say, occasionally failures do occur, but we can not explain. Really is your engineering that bad? A high school kid could figure out that the spring is to strong for the plastic housing and over time the plastic cracks. Really Whirlpool? A multi billion dollar company? Never again Whirlpool.

Purchased both Cabrio washer (wtw6200sw2) & dyer brand new in 2007 for $1200. Within 4 years the motherboard went out. Whirlpool didnt want to fix it. They said it was past warranty. After many complaints to corporate, they sent someone out to repair it for $496 (they paid). Repairman said these models had motherboards from Japan & Whirlpool was aware of the many issues, but wouldnt do a recall. 2009, the springs went out, 2011 F codes began to appear. Clothes dont get clean; not enough water. 2014 & 2015 DU & DL codes appear. Now I need a new Lid latch assembly. These washing machines are not worth buying. Never again will I buy another Whirlpool!! My mom had an old Kenmore that lasted 20 years and only needed a replacement belt. No more fancy high end washers for me!

I have read the reviews and agree with all negative comments. There is no point in investing in a high efficiency machine when I have to rewash many dark items several times in spite of always adding the extra rinse cycle. The clothes appear cleaner if I do not add liquid fabric softener, but as I prefer to use my clothes line when possible, I am unable to use fabric softener. Also, although it is supposed to be a high capacity machine, I only fill the tub about one third of its capacity, hoping this will increase the cleanliness of your clothes. It doesnt seem to help.I have contacted Whirlpool several times and the final suggestion was that pay for a technicians visit, approx. $100, plus extra for repairs. I have decided not to throw good money after bad and to buy another brand of washer. This is the WORST appliance I have ever owned even though it is supposedly high-end. PLEASE do not buy a Whirlpool appliance. If the Cabrio washing machine is an indication of the quality of their appliances, you will be wasting your money.

Just bought this washer, its making a lot of noise, sounds like something is grinding (metal, gears, etc). I thought Whirlpool was suppose to be good. I just had my Maytag go out after 18 years of service, thought about getting another Maytag but found out Whirlpool makes those. As many complaint as I see, seems there needs to be a class action lawsuit against Whirlpool for shoddy work.

Purchase whirlpool washer model W2W4800xQ2 in Sept. 2012. Had problem with lid lock after warranty. Now lid lock does not work, takes 1/2 hour to start wash and does no spin. Called whirlpool and they will do nothing. Repair will be $200. I opt to just purchase new machine. This machine is one piece of garbage.

If you want clean clothes dont buy this machine(Cabrio Washer)! First of all I find that my clothes have dry spot on them when I pull them out of the machine. Whirlpools response is that the machine spins at such a high rate that the cloth will actually seem dry. Doesnt make sense to me that a shirt that has another garment on top of it gets dry in an unexposed area. I have also been told to always use the high water setting. This helps but the clothes still are not clean. Also my dark slacks come out with residue lines on them - Whirlpools solution; never wash anything in cold water. In addition the machine is very noisy. It sounds like the water pipes are being kicked out of the wall. And forget about washing a king size comforter as advertised, a twin comforter doesnt get clean or even thoroughly wet and residue lines are left behind. Hate this machine! So glad I didnt buy the extended warranty since my attempts to have them stand behind this product have failed. I feel the money would be better used towards a different brand.

My Calypso washer is broken AGAIN. I have spent more in repairs than the machine cost originally. After more than a dozen emails to customer service they have still not answered me even once. Its obvious they put as much pride in their customer service as they put into the assembly of their products.

My husband and I, purchased this washer on November last year, I used twice before and I noticed that the clothes felt hot, but the cycle was COLD water. Now use it again until June 2015. In every cycle the clothes were hot, I started calling to get an appointment in June at the 1800-253-1301, but the system was down twice. Then in July then again the system was down, then August 10, system was down. I did not wait more and called back the next day, August 11, got appointment for the 20. A technician came, he told me that the hoses was switched, but I know the hoses was installed correctly, my husband was here at the installation. He knows the proper installation of the washers.

Purchased a matching set, Whirlpool Cabrio Platinum Washing Machine and Dryer in November of 2012. After just over 2 years, Im stuck replacing the Washing Machine at my expense! The washing machine began leaking water out of the bottom of the unit and became extremely loud when operating it. The repair technician said it was a seal and bearing that needed replaced and the cost of repairing the unit would be cost prohibitive versus replacing the unit all together ($800+)! Originally paid over 2K to purchase these units and have them installed. I do not want to trust or rely on the Whirlpool brand again. I would appreciate any recommendation for a better quality, high capacity, HE washing machine brand to replace the Whirlpool unit with (Samsung, GE, LG)??

The machine is two years old. It cost over $1,000 to buy. From the beginning, we have had mold issues with the machine. The entire house fills with the smell of rotten eggs every time we use it. The machine is used daily so it doesnt sit for long periods. Despite all the complaints online about their machines, Whirlpool refused to acknowledge that there is a design problem with the machine. They refused to make any repairs or buy the machine back and their only suggestion was to buy more chemicals from them to use to clean the machine. We have done this in the past to no avail. Oh, they did offer to send out a service company but on my dime. Whirlpool needs to be sued and I only wish that someone would start a class action suit against them. It really stinks when you try and do the right thing and buy American only to have the company not give a crap about their customers or the fact that their product is garbage. About 10 years ago, I had a Maytag front loader washing machine with the same problem. Maytag bought the machine back on a pro-rated basis, no problem, no question. Of course, Maytag is now owned by Whirlpool. Too bad they didnt adopt Maytags customer service policy. I cant wait for them to go out of business - something they deserve.

I bought a Whirlpool washer and drying matching set (model 6400sw3). I liked it because it was extra large without agitator in the middle. Ive had it for about 2-3 years and I have already replaced the drain pump, motor and barrens, it has cost me over 500.00. I thought now OK its working fine, but now its giving me a code every time I wash of LD. I am so fed up with this!! I should have bought a new washer but I felt as much as I put into it, I basically built a new one. And now this code comes up every time and I have to power it off. Im not sure if anyone else has had this problem but I just dont know what else could go wrong with this. I will never ever buy a piece of junk like this again!!

I bought a Cabrio top loader in 2007. Have now replaced a pump for the 2nd time. Replaced a circuit board once. Thank goodness the machine was purchased at a local appliance store who stand behind what they sell and are very prompt in their response time.

These washers are known to rust terribly from underneath the bleach dispenser. Please note that if not detected within the 1st twelve months from purchase, then Whirlpool will not stand behind their product. I would highly recommend not purchasing the Cabrio top load washer. Extremely dissatisfied with this product and warranty.

I cant even tell you how disappointed I am. This washer has destroyed my clothes and towels. Ive tried to reach out to company but they want me to call for service. What would I call for? Washer works, it just makes holes in clothes, in towels. There are so many complaints about this. If anyone know how to begin a process like this, please let me know. Trust me, when I write a review about something, its got to be either really good or really bad. I dont have time to write things like this.

I purchased my Whirlpool Cabrio washing machine a couple years ago at Lowes. It sucks. First of all, my washer stinks all the time. It smells like sewer even after the cleaning cycle. My dark clothes come out with a white residue, and my whites come out with dirt on them that wasnt on them before washing... All this even after running an additional rinse cycle. How is this energy efficient? Not to mention, time efficient??? Crazy that once you buy something like this for this amount of money youre pretty much stuck with it... Isnt there a lemon law for appliances? This was so expensive and such piece of crap. I will never buy a Whirlpool washer ever again!

Whirlpool Cabria Washing Machine hold down switched failed in just 18 months of use. It took the Technician 5 days to serviced and repair our Whirlpool top loading washing machine. The washer is till acting up and stop working unless you put a weight on the top loader cover.

I purchased a very expensive Cabrio top-loading washer thinking I would never have to worry because supposedly it’s the top of the line, right? Well, I have it a few years; the first week they replaced the basket because it was ruining my clothes. And then I had to replace the pump because of a coin getting caught and putting a hole in the pump. Really? What the heck? Now the basket is all shredded at the top. Obviously that isn’t right, so what do I do now? Replace the basket again? Who gives them the right to charge so much for a piece of junk? Plus, it’s supposed to save on water, but I feel that the clothes don’t really clean well. They hardly feel wet coming out of the machine.

The washer is only a couple of years old. It does the job but its not something wonderful or great. The previous one was a Kenmore but it was built by Whirlpool. It works. Thats all I can say about it.

I called customer service line regarding my Cabrio Automatic Washer (Model No: WTW6600SW2; Serial No: CU2171019) purchased on 11/24/07, to report and ask for assistance with a chronic ongoing service problem. Several calls in the past and service visits (at my cost) did not rectify the problem. Although there are many similar complaints on this machine regarding the loud noise and resulting problems during the spin cycle that involve the tub and rods, the representative said So sorry or Too bad we cannot not help you.My machine now does not run and is less than 4 years old --just like every other report. I get an error message F which the representative alluded to something involving the electronics. Machines purchased in 2004 from Whirlpool have across-the-board similar problems that Whirlpool refuses to take ownership for. This machine is their top of the line model. I dont feel the financial burden of repair or purchase of a new machine should be on the shoulders of the consumer. We bought in good faith from Whirlpool and expect Whirlpool to live up to their responsibilities. Thank you for any help you can provide.Rae **

I purchased my Whirlpool Duet washer about 14 months ago. After about 8 months, I noticed that it had started leaking. It was under warranty and the seal was replaced no problem. I then started to notice that my clothes were getting small tears in them. Around January (13 months after purchase), I got tired of finding new clothes and jackets with rips and tears in them. I finally found that the plastic piece around the entrance to the washer was rough and jagged. I called Whirlpool and they told me they could send out a service tech to file down the jagged edges. They told me this was a common problem caused by the zippers on jackets hitting the plastic and causing it to become rough. Because it was one month out of warranty, I would have to pay for the service call. The lady told me I could try filing it down myself. I feel like I should not have to file down anything 14 months after purchasing a new washer. I feel like I should not have to worry that my clothes are ruined every time I wash them. If this is a common problem as the lady told me, it appears to me to be a design flaw and should have a recall. I have lost several outfits and jackets due to this machine and I am very frustrated that Whirlpool would not stand behind their product.

Our 2005 whirlpool duet washer steel drum and plastic tub broke. My husband diagnosed the problem and opted to fix it to save money. The parts are under warranty but you still pay labor and technician visit running up to $250-$300. The plastic tub was obtained only if we paid for it $100 and the steel drum they sent under warranty. The plastic tub has a hole with a black plug and sensor in it. There is a discrepancy in the measurement of the old tub and new tubs hole that is slightly larger, therefore when installed a steady stream of water leaks out. I now have 3 plastic tubs as that was their solution, to send more of the same that did not measure correctly. An investigation was done to determine they were the correct parts. As asked we had a whirlpool technician come to verify parts were correct and being installed correctly and the parts sent would not fix the machine due to the hole discrepancy. Many calls were made to whirlpool and they continue to give me the runaround. They now are not taking their technicians information. The technician has given the information to 3 sales reps in the new england area and made several phone calls to whirlpool and no one is willing to give us a solution.

Purchased washer Aug 2012 and has increasingly been leaving white residue after wash cycles. Have used the Extra Rinse function to no avail and use half the recommended amount of HE Tide. Now I have to run the Rinse, Drain, Spin function twice with darks to remove the residue. I have also been doing the monthly maintenance which has not helped at all. This machine seriously detracts from the Whirlpool name and if they are unwilling to fix the problem, it only publicly displays the companys integrity.

I purchase a new Whirlpool Calypso with Catalyst Washing Machine in 2006 after a house fire. Thinking that I was buying a great machine. I was so upset with my house burning that I never thought about the washing destroying my towels, rugs and sweaters until it was too late on the guarantee. I called the company and ask if there were any more complaints about this machine, and of course they said no. I ask if there was a recall and they said no. I told them that there needed to be a recall of this machine. I so want them to see the towels that I have to use. I am so embarrassed of my towels that I have to buy new when company comes. I made no difference on the price that I paid for the towels. They all were destroyed by this Whirlpool Washer. I have had enough, I am buying a new Washer and it will not be a Whirlpool. I believe that the right thing to do is for the Whirlpool company to put a recall on this machine and give our money back. I had a friend that is in charge of another washer company and had him to look at it. He said that if that was his customer complaining about his washer that they would automatically bring the customer another new machine. I wish I had went with his company. Shame on Whirlpool for treating their customers like they have.

Cabrio washer - This was a huge disappointment, clothes not clean, sometimes still dry in middle even with small loads! Have had washer just over a year, second time it has quit working! This time it wont even give a code to why it wont spin out! Living on a budget, I cant afford such a shoddy product! Never again will I buy any product associated with whirlpool!

Its a great machine but the temperature control button is easily moved at times. The machine does a great job in washing clothes. Ive had mine for 10 years now and hope that I never have to replace it.

My washer is a top load, energy and water efficient model. I am amazed at how little water it uses and how well it cleans. I do have two issues, the capacity looks huge but it will not take a queen size and double sheet set in the same load. It unbalances and then cant seem to get going again. The other issue is that you cant pause the wash and adjust things, you have to cancel and start over.

I had bought from S C Shah & Co, Mylapore a Whirlpool ac 1 ton split magicool dlx cop in March 2016 and installed in March 29 2016 by Cool Control System, kodambakkam From the installation period we had a cooling issue and informed Shah & Co, Mylapore where we bought the ac. They came and checked and informed Whirlpool customer care. Within two months i.e. in May 2016 of installation Whirlpool again uploaded/charged the gas (the service engineers told us this is due to hot summer). Though again we had a cooling issue, we were under the impression as this is due to summer as explained by the technician. After that rainy season came and we didnt use the ac.As we are in December when we complained Whirlpool they said this is due to the copper wire gas is leaking and it has to be replaced and informed that though under WARRANTY, the customer has to pay for replacement (we have used only the 3 mtr copper wire which came with the ac only. we have not used any our own copper wire). Whether WHIRLPOOL GIVES SUCH A QUALITY COPPER WIRE which has to be replaced within 9 months. Now they are informing that you are calling us after 6 months of gas charging, so we cannot service. If you could have called within 3 months we could have serviced you. BUT WE ARE UNDER WARRANTY. NOT EVEN AN YEAR FROM THE DATE OF PURCHASE.Not responding to calls, disconnecting to the calls even if we call their Delhi number 011-49308500. Though under warranty they are not ready to do service and very rude saying, we cant do anything. So, if we buy WHIRLPOOL ac we have to beg them even for their technicians to visit our place. Or we have to do our own service EVEN UNDER WARRANTY. Their local toll free customer care numbers/service executives always give a recorded message saying they cannot service. SUCH A PATHETIC SERVICE.

We purchased this washer (Whirlpool Cambrio #WTW8000BWO) in December of 2014. It is now 3 1/2 years old and while the washer worked great til just recently, we now have to purchase a different one because this one will cost too much to repair. We did not get the extended warranty. I have since read that the Cambrio has had a lot of problems. Always check the long term owners and what they have to say about the item, would never have purchased this washer had I known what the problems were and that they even were having them they should have taken it off the market til they got the situation fixed.

I like my machine even though there is no agitator. It is a top loader so it does not smell. It is a water saver which, when I first got it, I thought that it could never clean the clothes in that small amt of water...but it does clean the clothes very well.

I bought this machine in September of 2014. Six months later I HATE IT!! It does NOT get the clothes clean and dont even try to bleach white towels or socks, it doesnt pump the correct amount of hot water and things come out just as dirty as when they went in. It tangles everything together and frequently stops working because it unbalances the load with its lack of water. Ive always been proud of how my familys laundry looked and now Im just embarrassed. Im considering donating this to a human society for dog towels. Stay away from this washer, its horrible. Im going to the laundromat and shopping for a new machine ASAP!

I purchased my washer about 1 month ago and I used daily. I went away for the weekend, and now it does not work. Washer will not wash, fill or spin, gives a LF error. All lines have been checked. I need to call service.

The washer buttons stopped responding after 19 months. Lid lock sensor didn’t work. Replaced control board because new sensor did not fix it. Went bad again after a week. I have to replace it. I think 1 year warranties are not enough for a major appliance.

These reviews re Whirlpool washer proves I can no longer trust Consumer review. This washer is junk. Does not clean, Takes over an hour to not clean your clothes. I have to add water to cover the clothes. They come out as dirty as they went in. Want an honest review? Check out the ones on Amazon.

My Cabrio washing machine is 3 years old, and is working the way it has been designed to work. It does not clean clothes and it consistently has a foul odor. Due to the odor, I must use the cleaning cycle with Affresh (pricey product) 3-4 times weekly. Even that is insufficient. Because it is in an indoor laundry area, the odor permeates the hallway and nearby bedrooms. The extra cleaning cycles are contrary to the energy efficiency of the washer, and detrimental to the severe drought conditions in California. When I contacted Whirlpool about my situation, they recommended I substitute bleach for the Affresh to keep the cost down.

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

This thing absolutely is total junk. It doesnt clean at all. I have to wash my sons sweaty uniform 3 times because the first two wash didnt clean it. A tub and washboard cleans better than this unit. A 600+ washer should clean the basic stuff. I remove clothes after it was finished and some of the clothes have dry spots where the water couldnt make it to. What kind of washer leaves clothes dry?I wish I came across this site when I was at the store. I did a search and the manufacture website and retail gave it positive reviews. I pretty sure the Whirlpool is paying people to write positive reviews. Technicians have come and gone telling me that there isnt anything wrong with it. That their diagnostic isnt detecting anything. Well when I call them again I will have the tech wait while I wash my sons sweaty uniform and then they can smell it after it goes through the wash. Im going call out a service tech until it works as advertise or they replace it. If I have to call them out once a week. That is what I will do.

Cabrio Washer - We were getting unbalanced load messages and the washer would stop. I called in a serviceman and he said it wasnt worth fixing. It would be cheaper to buy a new one. This washer is only 5 years old.

It was not a good experience after I purchased a Whirlpool washer in Feb 2014. I have been going to Laundromat 5 months since I found the door did not able to secure. I reported in January 2015 and technicians from 3 different contractors made more than 10 visits for checking and replacing parts. Not only nothing gets done, I also missed work for all these days. Then I escalated to the Supervisor, ** and Miss ** in Executive Office of North American Region. Both of them are very nice that they understand the situation and how frustrate it is. Finally, ** said Whirlpool would replace it. ** told me that I should get phone call from H.H. Gregg within 48 hours. However, it has been two weeks and seems no one care. In this three days memorial weekend, I still need to go to Laundromat while they are enjoying BBQ with their friends and families. I dont know how long it take to replace it.

Awful customer service. We bought a washing machine in 2010 and it has shredded a ton of clothes over the years. I called customer service to see what they could do to help me with this problem. After about 45 minutes of trying to get more than a service that I would have to be responsible for, the supervisor offered me a new washer at a discounted price. I went online to compare and found out I could purchase the exact same washing machine at home depot & best buy for $50 cheaper. I called back to see if there was anything they could have done and they would not budge.Shame on you Whirlpool. You have lost a customer and I will make sure no one I know buys one of your products ever again. I cannot believe that you would not make any accommodations for us. We bought that washing machine with the intention of keeping it for 15 years. It has cost us countless amounts of blankets, shirts, pants, etc. I cant believe you wouldnt help us after all the money this piece of junk cost us.

The machine never allows enough water to clean the clothes and I do not have the option to add more water or to spin the clothes again. The maker of this machine must think that people do not have the ability to know how to wash clothes or think for themselves. I need a washer that I can tell to add more water or just spin these clothes again. Very disappointed. I need an older model that I can control.

I hadnt had the machine. In no time, I started noticing brown rust looking spots on my whites and light colored clothing. I got to looking and had rusted out all around the bleach dispenser, entire area on the entire top. I was told to replace it. This would be about $200. Ridiculous!

I bought a front loading Whirlpool washer a few years ago after having my old top loading Kenmore for 25 years. It seemed okay, but I did always have to leave the front door open and it always smelled musty, which was of some concern. My clothes never smell totally fresh. The biggest current problem is that several months ago it started with a failure code, alternately would stop without draining, wouldnt fill, or wouldnt drain, and ultimately ended up flooding my basement. So we called for service and they replaced a sensor and said these machines seem to have a lot of service issues with sensors blowing and motors dying. So I paid them that time. Now its a month or two later, failure code again, calling for service one more time. But if it costs too much I will join the legions of dissatisfied Whirlpool customers and will switch to an upright competitors brand.

All of these awful reviews and you continue to sell the Made in China JUNK!!! And shame on the stores that advertise and sell Whirlpool JUNK!! They should put a warning on these machines stating Will not last, gets off balance and does not clean your clothes. Yes we bought the Cabrio like the others, our clothes would not get clean, because like sheets, would end up looking like a doughnut without a hole and all of the dirty water would drain through the middle and make a spot. Then you have to wash them over and over. But that is not the worse part! It only lasted 13 months, YES I said 13 months just past the warranty LOL!!When the man came to make repairs, it was the gear box and was going to cost almost $600. Almost as much as we paid for the machine. He recommended getting a Speed Queen, we did and I LOVE it!! I think it is the BEST MACHINE I have ever had. They are a little hard to find though, but I found where they were sold on the internet and the dealer had to order it. Well worth the time and trouble, (trouble) which I dont expect to have with this machine. Like I said it is a wonderful beast. And I will never buy another product made by Whirlpool. Before my husband retired he made prototypes for autos so he knows about testing and Whirlpool had to know this product had bad flaws before they put it on the market, I call that fraud. Bad taste in my wallet, Michigan.

I have always chosen Whirlpool or a Whirlpool product such as Kenmore or KitchenAid. Preferably with an actual agitator in the tub. As a very capable handyman, repairs have been easy and relatively reasonable in cost. My units are 15 years old and going strong.

After 2-1/2 years we started having trouble with the spin cycle on our Maytag washer. We live in an area with no repairman. Whirlpool want us to pay just to talk to us. Now the timings off. It will not spin out.

My son purchased a Whirlpool Cabrio washing machine about two years ago and now it doesnt work. It was an almost $1,000 machine. You would expect a higher quality product. I always bought Whirlpool products because they were so dependable so I recommended my son to go with Whirlpool. Big mistake, the panel lights up but when you press the power button, nothing happens. I do not recommend this machine to anyone. Im wondering if anyone else that has purchased this has had the same trouble.