I have a Whirlpool cabrio washer (Model: wtw6300 Serial Number: CT3573525) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. At the beginning, I didnt care because I had warranty with BrandsMart. I had to call at least four times. But now, I bought the automatic control and it didnt work. For two days, I was trying to balance this machine but it is impossible since the beginning.I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool. Two of the gas burners of my Whirlpool kitchen, after two years of use, are no longer working. I will definitely contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!

I purchased the Whirlpool Duet June 2011. Within two weeks, it was tearing my clothes. It didnt matter how little of a load it was, they still ripped. Five months later, my machine was leaking water. The repair man came out. I told him it was also tearing my clothes. His only response was dont load it to full. Well, I called the store where I purchased it and they are sending a repair man out again. I told them to either fix this from ripping my clothes or I was going to take a hammer to the machine and never buy a Whirlpool again or give them a good reference. I also called Whirlpool directly and told them of my problem and they acted like they had never heard of this happening before. I told them to search the internet because everyone is having the same complaint! I had a Fridgidaire front loader for 9 years and never had a problem with it eating my clothes.

This is about my Whirlpool Cabrio top load washer machine (model number WTW6200SWD, serial # CT3670597). I bought this machine in 2007, and soon after, I was having problems with the F1 code. After several trips back and forth to reset the code, so I can get the laundry done, and many frustrations, it was time to call Whirlpool to resolve the problem. I find out that there was a recall for this ongoing issue. They sent a technician to replace the mother board, and everything was fine for some time. Soon after, the machine was giving us more problems with the F1 code, and the UL code. It doesnt matter which way I try to balance the load. This piece of junk will not work. Whirlpool needs to stand behind this issue, and recall this washing machine for good. Every customer should be entitled to a full refund, and a compensation for the many hours of electricity, aggravation, and frustration, wasted trying to get this junk to work.

The agitator is higher than any I have seen and when we washed aprons that have plastic buckles on them, they get stuck under the agitator. When complained their solution was to use laundry bags to wash 15 aprons in, they are long aprons. Paying a lot of money for the machine and it being commercial I didnt think we would not be able to use it. The whole machine shut down when three of the buckles got stuck. The washer is model # CAE2793BQ and I would suggest that no one purchase one of these machines.

I have the 4.3 cu. ft. washer. This washer worked OK, but the lid lock does fail after about one year if the washer is in an environment where moisture may be present.I noticed the lid lock not working all the time about two months before the warranty expired. If this happens, call the warranty department immediately. After checking the ground wire and resetting the washer power over and over again, the lid lock finally stopped working completely. Here is how to fix it:There are two screws on the back of the top portion of the washer. Unscrew them from the silver straps. The washer lid will now push forward and up and off. Prop it up with a stick.Unscrew the two screws on the lid lock and start taking it apart (after reading this entire review). Be careful not to lose any parts and be sure to know where everything goes for re-assembly. Take pictures if necessary. Take the lid lock completely apart including any small pieces.The plastic slide needs to be cleaned. It has a spring that may fall when you pull it apart.The metal contact points inside the lid lock mechanism need to be cleaned. Be extremely careful when pulling the red cover off of the housing assembly. Pull the four metal contact points completely out of the plastic assembly. Be real careful with the black plastic slide piece, the metal rocker switch and the switch actuating motor. Use a small file and rubbing alcohol to clean off any green or white corrosion. Make sure to check all contact points.Re-assemble and you will immediately notice the lock switch working better. Re-install onto the machine. Re-install the upper portion of the washer. Start your laundry. Repeat after one year or when the lid lock becomes faulty again. These points should have been made out of a less corrosive material. Poor craftsmanship. Would not recommend.

IM OLD AND DISABLED WOMAN. Bought a brand new $800 Whirlpool top loader washer and it wont work after not even a month. Called whirlpool and had the worst customer service from Tammy. I have to wait to compose myself to call back cause the washer is junk... F9E1 SENSOR. IM NOT A MAN! Worst customer service. Thought my washer would last longer. Its been 1 hour 45 minutes. Wont turn off. I CANT unplug TAMMY! IF I COULD I WOULD!

My washing machine is a front loader. Previously I would not have purchased one, but after using it for a year or so I have changed my mind. As long as I do not overload it my clothes come out perfectly clean using cold water, and partially dry so needing less drying time.

I bought a Whirlpool Duet Front Load Washer in 2008 and it began showing F71 and F70 error code in 2011. I paid approximately $1,000 for the machine. The washer wont finish the cycles and often wont start. When I press the power button, I hear the 3 beeps and after a while, shows the F71 error over and over. The information I gathered online indicates that many people have the same problem. The repair cost is at least $550 to replace the user interface circuit board and is no guarantee. This is ridiculous.How could GE sell consumers this kind of junk that fails to work only after 2 years. I had a top loader for 12 years with no problems, not a single repair call. My wife and I are extremely frustrated with piles of dirty clothes and no washer to clean them. I want GE to refund the cost of the washer on a 10-year prorated basis. This is only fair.

These washers are known to rust terribly from underneath the bleach dispenser. Please note that if not detected within the 1st twelve months from purchase, then Whirlpool will not stand behind their product. I would highly recommend not purchasing the Cabrio top load washer. Extremely dissatisfied with this product and warranty.

We bought a washer in Sept. 2014 and it was used for 4 months before we left and went south for the winter. When we came back in May, we started hearing a loud banging noise so we notified Whirlpool since we were still under warranty. They sent a repairman and he said he needed to take the washer in so he could repair it. They have sent the part out 3 times and they said it was chipped or cracked so another would need to be sent. This has been going on for 2 months that weve been without the washer and today we checked and supposedly another part should be coming. They tell us our warranty is only for parts and labor not replacement. Help would be appreciated. Thank you.

Whirlpool has been a trusted name for us for many years. The large tub has cut my wash load in half. Large towels to delicates have never been a problem. My washer is going on 12 yrs old and runs like a champ.

Worst appliance of any kind that I have ever used. Has only on/off button, in effect. Wastes water. There is no option to change anything once cycle has begun. No soaking. Occasionally, the machine simply decides to stop and drain itself so that you can start all over again!! No idea how long cycle is. Nearly done? No idea. No matter what temp or how much detergent or how much water, the clothes are not clean. The lid locks and so there is no way to know whats going on. I suspect there is very little water during rinse cycle. All of the whirlpool appliances are similarly horrible. Washer is the WORST. Shame on you Made in America.

Contacted Whirlpool - unit (Cabrio washer 7600xt) is out of 12-mo warranty. Spoke with manager, Tracy **. She said they would not help - out of warranty. Called local parts/service center - ea. hinge is $42 plus shipping and labor to install. Obviously this is a defective design. The lid is too heavy. I was having a difficult time deciding to spend 150-200 dollars every 2-3 years for hinges on a $700 washer and then I read all the other complaints about Whirlpool washers. I will sell it for scrap and buy a better brand.

I purchased my Whirlpool Cabrio H2Low from Sears 6 years ago. After numerous problems with clothes not getting clean (soap spots, stain transfers, etc) I learned the only setting I could use that actually cleaned was bulky with an extra rinse (so much for the energy efficiency). My first major repair was in the first year. Weve since had 3 more and the darn thing died again this morning. First the motherboard died and needed replacement, the drain pump failed, the door lock failed, and twice now it stopped spinning. At first I thought maybe I was just unlucky and bought a defective machine but repair sites are filled with reports of similar problems with these machines. I will never buy another Whirlpool product again.

Whirlpool Cabrio - This expensive machine should be called the Presidential. First it spins, spins, spins. It sprays tiny amounts of water, so little, that there is 2 inches or less. There isnt enough water to cover the clothes so no agitator to stir and mix them. There are ridges on the bottom of the tub called aggrivators to twist everything into pretzels. This twisting spreads the dirt around, but does NOT remove it, the utter lack of water giving it no where to go. I use a hose to add extra water, and I hand soap dirty spots. I stop the washer frequently to hand rub and slop the clothes around and un-twist them. Explain to me how running this machine 3 times plus adding water saves water and energy. I cant, in good conscience, sell this POS to someone else, and I cant afford something else. I sure miss my simple reliable old Maytag. I could say even more about this atrocity, but not now. I HATE THIS POS!

We spent a lot of time researching to make sure we were making the right choice, found the one that was right for us. When it got delivered there was a problem though, the plastic scratch protector film they put on the doors for delivery left an adhesive residue that looked like dull spots all over our new shiny black doors. I immediately opened up the owners manual to see how they recommend removing this blotchy sticky residue, assuming we werent the first ones to ever come across this problem, unfortunately they only provide generic cleaning tips. So I went to their website and found what I was looking for. I tried all of the cleaning methods they provide, none of them even came close to working. So I grabbed some adhesive remover and tried that, it worked great to remove the residue however my microfiber cloth (which they recommend explicitly) started leaving scratches all over the finish.I called the customer service to see about getting a new door delivered, thinking this wont be more than a 5 minute phone call since I had followed all of their steps they provide both in the owners manual and on their website. Heres where I find out that their policy DOES NOT cover scratches/cosmetic damage, period. I tried reasoning with them, I had them read their own recommended cleaning procedures, and we both concluded that I had followed their procedures to the T! You might think that if the all of the typical procedures didnt resolve the issue, that would be the point where the customer service reps would have the ability to make a decision that satisfy the customer, you would be wrong! They kept telling me over and over that their policy doesnt cover cosmetic, therefore there was nothing they could do. It was delivered with a defect of sorts, how is the customer responsible for that? The only way I can see it having worked out in my favor is if I had never tried to clean it myself and immediately called customer service, I still fear they would have given me the same line of cosmetic damages are not covered even if I would have tried each procedure with them walking me thru it over the phone. Lesson learned, I will never purchase another Whirlpool product!

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

My Duet Sport washer drum is damaged due to the poor quality of the bearings. I replaced the Whirlpool Duet Front Loader Washer Bearing & Seal Kit W10253866, W10253856 but because the bearings were damaged the drum is also damaged. When I opened the rear panel of the washer the bearings had literally come apart and bearings fell out. All of the floor and the oil/grease was everywhere. I replaced the bearings but it didnt matter because the drum is warped. Priced the drum and it is nearly $400.00 to replace the assembly. The cost of the drum assembly is about half the cost of a new washer. I will never buy another Whirlpool product again. Just a shame that the cost of a replacement drum is so high. What caused the bearings to just explode and damage the drum. What did I do to cause this? Absolutely nothing. I have since discovered that this is has happened to scores of people with this same washer.

After owning the Cabrio washing machine (WTW5700XW, purchase price $629) for approximately 18 months, it began stalling at the spin cycle, leaving the clothes sopping wet. We found we had to unplug the machine to reboot the computer, and then we were able to manually choose the drain and spin cycle to complete the cycle. Before beginning a new wash cycle, we have to unplug to reboot again, or it sticks in a perpetual pump cycle.I scheduled a repair appointment from the Whirlpool automated service system. The repair man determined the computer control panel has to be replaced. Diagnostic service call was $136, repair est, $321.67, repair service call, $60-130. Total repair cost on an 18-month old machine was $520+. I declined the repair in hope of getting extended warranty coverage from Whirlpool. Nobody has responded to my email complaint from one week ago, not even a computer acknowledgment of receipt of my email.

I purchased the Cabrio washer during the black Friday sale. The washer was a pretty slate gray. I loved the color and the fact it was a Whirlpool, which I thought meant quality. It was expensive but we were updating our appliances as our 10 year plus washer needed replacing. Big mistake. This washer is terrible. It keeps me stressed. There is not enough water to clean the clothes, my husbands white underwear is always dingy and dirty looking. The sheets are dirty and smells. I try putting bleach on whites before washing and the whites still come out with underarm stains. I tried all the recommendations to no avail. This machine is awful. This was a big financial mistake. As soon as I am able this machine is gone. Will go back to the agitator in the middle, and NOT a Whirlpool. I DO NOT recommend this machine unless you want something pretty because this is NOT a washing machine.

We purchased a new Whirlpool washer in March 2010. Yesterday, 2/19/12, the washer stopped working. We called a repairman who checked the machine and told us the motor needs to be replaced. We called Whirlpool today, 2/20/12, and were told by their customer service department that since we did not have an extended warranty. We told them that we believe the motor should last more than 2 years. Their response was that if the motor lasted more than a year that was all they cared about. The only thing they would do is replace the motor if we gave them $299.00. I think it is very clear that Whirlpool knows it makes inferior products as they fail to stand behind what they make. I will never buy another Whirlpool product and would advise anyone who is looking for a washer to buy something other than Whirlpool.

Whirlpool Duet 2009 Model WFW9400SW02 - Worst experience ever with a new Whirlpool front Load washing machine. It broke down with error codes F28, F70, F71 13th month just after warranty and was leaking water. Bought 1 yr 153.00 Whirlpool extended warranty. Many reviews in internet have same complaint. Immediately had it repaired after waiting my 60 days to use warranty, but did not work after the door latch switch and one of 3 main circuit boards was replaced which was over $600.00. That was 2 visits. Fired them and had warranty company send different repair Co. They came twice with a cost of $840.00 and worked for 30 days and then had no power. 3rd repair company came out and wanted $350.00 to order part. I was offered $1195.00 cash or $1499.00 replacement top of line Whirlpool WFL98HEBU. Nice! But only 1 year warranty and I had to pay 200.00 shipping. I decided to take the money since I did not want to risk the break down on the new washer. The reviews on the new washer were not favorable with break down as the main complaint. 4 repairs in 1 year is lemon law on my warranty. My repairs were 4 in 45 days.

My husband and I purchased a new Maytag top load washing machine from Best Buy in May 2017. On June 19th, a month later, as I am washing, all of a sudden the machine dies down. I checked everything from the outlet, the plug to the circuit breaker, and nothing seemed to help get my washer to start up again. Unfortunately I had wet clothes inside and the lid is one of those that locks itself and it would not open. :( I called Whirlpool/Maytag to explain my situation and could not believe that they told me that they only have 1 authorized appliance repair dealer they work with in my area and that they didnt show any available appointments until 4 weeks from now? WHAT? Are you kidding me? I could not wait that long, especially since I had soaking wet clothes sitting inside the washer.I asked if I called someone else myself and have it repaired sooner, would they reimburse me for the expenses. They refused to do that and told me I need to wait for their own authorized repair dealers. Talk about bad customer service here :( My husband called them back and asked to speak to a supervisor at Whirlpool and was told that it shouldnt have to be that long for us to wait for repair so why was I told that in the first place? The supervisor proceeded to tell my husband that we will get a call back in 5 days? ARE YOU KIDDING ME? 5 days just for someone to CALL us? And then have to wait longer to get our service done? No way!We think that Whirlpool sold Best Buy a lemon and we are paying for it! Why cant they say that they will get in touch with Best Buy so they can deliver a new working machine and take this lemon back? We are not happy with their responses so we will be paying Best Buy a visit to see what else we can do. I already spent unnecessary money to go to a laundromat to wash clothes :( I would recommend that people stay away from Whirlpool products. Well see if we can exchange ours for another brand.

My landlord replaced our old Whirpool topload washer with a Whirlpool HE topload machine last year. Looks sleek, lots of settings BUT IT DOES NOT GET CLOTHES CLEAN - not on any setting, not if loaded as recommended or under-loaded, not if I use more or less detergent, and not if I follow all the tips for getting rid of residue. This machine so under-performs I have to spot clean my clothes AFTER I was them. And were not talking deep dirt or grime here, or things that need special treatment, Just ordinary dirt dirt, to which the machine adds gray streaks of dirty water residue. Thank God I didnt buy this turkey for myself -- I will NEVER buy one of these machines. I did two small rugs today and they came out dingier than they went in. These machines should be recalled. If I could give it less than one star, I would.

I purchased Whirlpool top loading washing machine model # WTW57ESVW less than 2 years ago. It stopped working yesterday. I had a trusted professional repairman evaluate it today. The motor needs to be replaced after less than 2 years?! The customer service reps basically said sorry. I should have purchased the extended warranty. Is it not reasonable to trust that a Whirlpool washing machine motor should last more than 2 years.I am very unhappy and very angry that Whirlpool will not stand behind their product. The last customer service rep I spoke to suggested she could send one of their repairmen and replace the motor at a cost to me of $299.00. So, after less than 2 years, I am offered an amount to pay of about half the cost I paid less than 2 years ago for the brand new washing machine. My home is full of Whirlpool appliances. I have been a good and loyal customer for over 30 years. I am very angry and upset with Whirlpool. Please explain to me why it is not reasonable for me to trust and believe that a Whirlpool top loading machine that is well cared for and not abused in any fashion should last longer than 2 years? Is this being a loyal Whirlpool customer gets you, I should have purchased the extended warranty”? We are talking about a motor here, not a fabric or bleach dispenser that breaks. Although, those parts should not break either, there is a big difference from something like that and a motor. Please contact me as soon as possible at either number listed above. Thank you.

I purchased my new washing machine in September 2011. When I removed the clothes from the washer after the first wash, I noticed that there was soap on several of the items. I ran them through another rinse and spin cycle, and there was still soap on several items. In an effort to avoid this problem, I no longer use the soap dispenser tray, and use the bulky cycle to get more water in the tub. Like most of the others, the clothes are tangled and stretched from one side of the tub to the other. Also, it takes 1 hour and 36 minutes to run a complete cycle. The manager of Sears tells me, that because of government regulations, that in a few years, you will not be able to buy any other type of washer. I purchased this machine, because it was highly recommended by Consumers Report magazine. I filed a complaint with them eight days ago, but have not had a response.

I am so disappointed with this washer. I totally dread doing laundry. The following are the complaints: Every load comes out totally twisted and wrinkled!! The soap/fabric dispenser holds water after each load (I have to take paper towels and get the dispenser empty!!!). There is not enough water to properly clean the clothes. I have never noticed a reduction in my water bill and have had this piece of junk since 4-25-13. There is NO short cycle on this junk machine. There is an odor to my towels - like they are musty - after I dry them and use them. I use Tide HE detergent and clean the washer with Affresh (you shouldnt have to clean a washer). I should have taken the time to write a review much sooner, but decided today was the day after doing laundry. DO NOT BUY THIS WASHER.

I purchased a Whirlpool front loader as well as an extended warranty. The machine worked well for about a year and a half until i noticed rust patches beginning to form on the front of the machine. We contacted the retailer that we purchased it from and they suggested that we call the people that we had bought the warranty from. Unfortunately, the warranty does not cover rust, so we have to wait for it to rust out and just buy another one. It is only 2 and a half years old and is totally rusted across the front of the machine! It is extremely unsightly. This is the second Whirlpool washer that we have bought and the second one to rust out on us. I would never buy another Whirlpool appliance, and extended warranties are not worth the paper they are written on, let alone the amount that you pay for them!

We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.

Whirlpool Cabrio washer (WTW6400SW2) - After a few years of working, my washing machine lists a code of F50 and will not spin. After three visits from a repair company, they couldnt fix it and said we need to buy a new one. It seems like an electronic problem, but we have to replace the whole machine. Consumer Reports says a machine should last 10-14 years. Numerous people online have stated the same issue with the same model. More than one person stated there is already a class action lawsuit on this machine? Please help. Who can afford a new expensive machine after a few years of service?

We purchased a Whirlpool Cabrio Washer and Dryer in 2007. The washer sounded like it was going to take off and started leaking water. Two repair techs later, we found out it was the center bearing. They actually laughed and said they saw it all the time. It could be replaced (you need to replace the whole drum) for $300-$500, but I was told it would never be the same. I spoke with Whirlpool numerous times and they said they would do nothing, and I should have purchased the extended warranty. All I ask is for a company to stand behind their product. Im very disappointed.

I purchased an extended warranty with my product purchase and only a year and a half into using this brand washer the lid broke on one side at the hinge, it looked really rusty and like others I thought I was making a very decent purchase because all of my previous appliances were Whirlpool so figured Id keep up with the brand. Sad to say that was the worst decision I could have ever made for 13/1400 dollars for a washer with a light inside. Never again. They wouldnt even keep up the warranty because they said it was too expensive to repair it. Whirlpool is very bad for business...

I purchased this washer model WTW4950XW0 new. Within 6 months, it stopped spinning and was repaired under warranty. The spin actuator was defective. Great. A few months later, it stopped spinning, repaired under warranty and the spin actuator was bad. A few months later it stopped spinning, repaired under warranty, and the actuator was bad. Great. Another few months it stopped spinning again. This time, Whirlpool sent someone to repair it, another bad spin actuator. This time we had to pay for the part. So now that we are completely on our own, it stopped spinning yet again. Let me guess. The spin actuator is bad!!! Incredible. What a piece of crap. This washer was never used heavily.

Purchased an expensive, Cabriolet Washer in 2014 to replace a well used Kenmore washer. Sucked into the, Whirlpool is a good brand and spent more than I would have. Lid lock fault started about 3 months ago, googled fix and found this to be a very common problem with this brand. Have been able to override and reset it but it is very frustrating to deal with. Called in a repair person this morning who, for $140 told us we had a faulty lid lock and for $360 he would replace it. I contacted Whirlpool and asked if they were aware of this very common complaint (just google it) and they were not but offered to make a record of mine. Please do not buy Whirlpool. Very disappointed with their product and their response.

I am 72 years old and this Whirlpool Energy Star HE Washing Machine is just useless. It does not clean clothes properly. It always leaves a stinky washing machine smell which never goes away despite no matter what you do. A completely useless, faulty washing machine! Never ever buy a Whirlpool HE washing machine! Some websites say that you need to buy a washer fan at a cost of $69.99 and attach it to the back of your washing machine as this is the only way you can get rid of the smell. Who has that kind of money? Why is this fan not already included in this washing machine if Whirlpool is aware of the smelly washing machine/smelly clothes problem? This is such a joke! We would like to be reimbursed for our deficient Whirlpool Washing Machine or at the very least, have a recall of this inefficient, poorly designed washing machine. Report them to the Better Business Bureau and anyone else you think can resolve this problem - thanks!! - Unhappy camper

We bought the Whirlpool top loader washer and the drum broke down and after several attempted fixes it was replaced by new one as we were being financed through a business. So here comes the new one - same exact washer. Not only did it not clean well (normal soiling) then it goes to ul which means not balanced... not because clothes arent but because the thing that balances - it went only after a yr!! It would also keep filling draining again to no drain leaving clothes SOPPING wet... So very disappointed to say the least. What a piece of junk this washer is!! Its going to the curb tonight and being replaced by GE - NO MORE WHIRLPOOL AGAIN !!

Purchased a Whirlpool WTW7800XW a year and a half ago. The left top of the washers glass pops up, making it impossible to use the washer unless I weigh it down. Apparently a screw has popped out to hold the glass in place. Whirlpool used to make a decent product, but thought I should pay them $129 for their time, just to come out and then an additional part fee. How about the 30 minutes I spent on the phone with no satisfaction. My time is also valuable. I gave them the choice to come out and replace the screw (which shouldnt have fallen out in the first place) or lose a customer. Fortunately, I have a husband that can repair it, but I am extremely disappointed that Whirlpool is now making substandard products. We are a family of 3, so its not like Im doing laundry daily. Am I wrong to think I can get at least 3 years out of a product?

After reading all reviews online on the lid of the Whirlpool Cabrio Washer, it upsets me that there has not been a recall on this. Our lid has snapped & has to be held down until the lock light comes on. Often times during the cycle it must sense the lid is broken & thinks it is not locked & sets the load off line. I have to pause the load & then reset the load & hold the lid down tight until it restarts.

I paid for an extended warranty. Dishwasher not functioning properly- it stops mid-cycle. Had a tech out twice who insisted nothing was wrong. Extended Warranty customer service refused to honor my claim. Will never buy another Whirlpool product again. And buy an extended warranty! SAVE YOUR MONEY!

The wife and I are retired and when it came time to purchase a new washer, we thought we would spend the money and buy top of the line so it would possibly outlast us. So we went to Lowes and spent $1000.00 plus on a Cabrio. Within the first year, the control board went bad, replaced under warranty, now no matter how little or much of a load the wife puts in this piece of crap, it goes off balance!!!Of course as previously stated, customer service doesnt give a crap because we also saw no need for an extended warranty having made such a large investment in a washing machine that we thought was built with a high standard of quality, SHAME ON US, SHAME ON YOU, WHIRLPOOL!!! You have lost a customer who has been buying your products for a long time but will never buy another and will be warning everyone we can to do the same.

I have a 1 year old Whirlpool washing machine (Model: WFW94HEXSW Serial:C04151969). The grease from the drum is found to be the cause of clothes being ruined during the wash cycle. I waited over 3 months for a replacement. The drum arrived broken. I ordered again, and it was then said to be on back order. The water shut off developed a slow leak, causing the water to fill, and flow out the front door, causing carpet damage. We have been forced to throw away good clothes, and pay to have our clothes washed, at a not so local laundromat. We feel it would be more than reasonable to have our washer replaced, and professionally installed immediately.

I purchased a Whirlpool duet set on sale at Lowes about two years ago. The front loading washer has been leaking when I put in a full load of clothes. It usually floods the floor when it leaks. I am upset and very angry because this leak has ruined the doors to my washer doors. Apparently, the defects with this machine was known by Lowes and the Whirlpool company at the time that I purchased it (thus the sale price). This was not forementioned at the time of purchase. What a lousy way to do business. Whirlpool screwed me. Shame on me. Never again.

We purchased Whirlpool sports model on 2/1/2011. We faced a problem with the motor in a month’s time. The service man told that there are fluctuations in the power so it went wrong. They replaced it after 15-20 days’ time. We also complained that it’s making noise and then he told that we should keep it on the stand. We did so, even then, it’s still noisy. Now about 3 weeks back, suddenly it stopped working during the wash. I never overloaded the washing machine. We complained to the dealer. The mechanic came and told that we had to replace some parts and he will get in a couple of days, but he never turned up. When we contacted the dealer, he said that the parts were unavailable and he will send them in a couple of days. I am fed up of that answer. We could have purchased IFB instead of this.

So I had a problem with the water heater after 2 years and had the sensor fix by my heating people. Now the water heater is 3 years old and started leaking from the top of the water heater. Called my heating people and they fix the pipe and coupling on top but he told me the water was still bubbling up at the top. He told me it could stop and 70% it would be ok. Went to check on it and it continues to leak so I called Whirlpool because it was still under warranty. They are the most horrible people to deal with. First of all I told the guy it was leaking from the top but he asked me if it was leaking out of the side pipe. Didnt know what he was talking about and he kept sighing on the phone. If I knew about water heaters I wouldnt be calling them. After all the questions it came down to it was leaking where I told him at the top. He gave me a number and told me to take the water heater back to Lowes and get a new one and then call them and they would move the warranty over to the new heater. Really???? We are not talking about clothes you want to bring back to a store. Asked him how I should do this and he told me to call a heating contractor. So does he think that the heating contractor and going to run the water heater back for a new one??? In the end I just called my heating people and they are going to send somebody out to install a new heater. So much for Whirlpools warranty. If this is under warranty and it is exclusive to Lowes then they should be having Lowes bring a new one and install it.

Purchased Model # wtw5000DW0 Jan 3, 2015. Aug 15, 2015 started leaking water. Certified technician came to repair. Aug 17 - new transmission. Sept 3 replaced new transmission with another new transmission. Sept 8 called master technician at Whirlpool, needs new clutch assembly. Both technicians stated they dont know what is wrong with the machine. Sept 10 new clutch assembly and agitator replaced. The machine still makes a horrible grinding noise and is unusable. The technician has replaced everything but Whirlpool says it is still fixable. The Master technician has no idea what is wrong with my machine yet he refuses to call it broken. I have been without a washing machine for 3 1/2 weeks. They refuse to offer a return authorization number. I have spoken to a Supervisor on the phone. She states the warranty is for repair. They wont admit their product is a piece of garbage. They have lost a customer. She stated she will put my complaint in a file.

Whirlpool Energy Efficient Top Loader - I re-wash at least 20% of all clothes because they have dark spots AFTER washing them, but NOT before! It is a moving target, wash out one dark mark; get another somewhere else. I bought great quality sheets that are permanently stained, because of this. No matter how you load this machine, anything with arms and legs gets entangled into a big knotted mess. It is difficult to separate them and time-consuming. This puts a lot of stress on the clothes, especially as the load spins. I also re-wash entire loads at least 4 loads because the clothes dont rinse properly. I bought a 5 yr. extended warranty and have had this serviced at least 4 times to no avail. THE PROBLEM IS IN THE DESIGN! I am POSITIVE of it. If you have these problems, as well, please contact me. I would love to investigate a class action suit. I am THAT mad.

Whirlpool Clothes Washer Model WTW4930XW1 - We have experienced tub overfilling on (2) separate occasions with this washer model in a period of time of less than (2) years. Through extended warranty service purchased, a technician came out the first time; declared nothing explainable to cause the malfunction, re-calibrated the control panel, and off he went. This second event occurred much the same as the first; happened to walk in to notice water on laundry room floor and witnessed overflow out the lid on top. We have carefully washed additional loads after this second event without a similar malfunction. From my online research, this sure sounds like a faulty pressure switch not sensing high water level in the tub. Any other thoughts?

We purchased Model WTW81920758200YW0 on September 8, 2012. Its performance has been unsatisfactory, not cleaning the clothes as advertised. Not long after the warranty expired the main bearing failed, bringing a local service technician and we were left with a bill of over $300.00. Yesterday, the machine stopped in mid-cycle. The display went blank and the lid lock would not release. I called a local service company for a visit and the soonest a repairman could show up was next week.A call to a service we had used for the bearing surmised that without knowing the cause of the failure they could only guess that a circuit board was at fault. That visit would be over $300.00 with labor and materials. That was the last straw. We broke the lid lock to retrieve the contents and took a ride to buy another brand of washer. We went back to the appliance store where we purchased this machine to buy a Samsung front loader. The salesman apologized for selling the Cabrio in the first place. Good money after a bad product.

A top loading washing machine with an agitator in my opinion, gets my clothes 100xs cleaner than one without. Ive owned front loaders and top without agitators. Never again. Top with agitator is my personal preference from now on. Also Whirlpool has never failed me unlike other brands.

I purchased a Whirlpool Washer at Lowes on 02/29/16. After 3 weeks it simply stopped after the last rinse, never drained the water or starting the spin circle. One and a half month later after 5 service calls still no working washer. Whirlpool customer service just adds insult to injury. They refuse to replace to washer or to issue a refund. Apparently they dont care if their customers have to use a laundromat indefinitely after buying one of their washers.

This was the first new appliance that I had actually ever had and I purchased it in October of 2010. After four months, it started make a grinding sound. I called Whirlpool and the repair man replaced the motor. Approximately four months after that, the lid got stuck and the machine would not respond. Same routine as before, but this time the transmission was replaced. While the machine was apart, I noticed the white insulating panel from the bottom was brown in a spot and looked as if it had gotten hot. A month before the 1 year warranty expired, the washer started making an intermittent grinding sound nearly identical to the sound made when the motor went out. This time a different service company was sent out my Whirlpool and the said that nothing was wrong. Now, the machine is out of warranty and has stopped cleaning close and during the spin cycle the you can hear water running into the machine constantly. Last months water bill shows a 40% increase in water consumption when nothing has changed to incur a larger bill. Seeing all these comments makes me wonder why the heck nothing is being done to force recalls on such poor products. Consumers should be treated with a lot more respect than this. I will never recommend a Whirlpool product to anyone I meet. In fact, I will strongly discourage anyone who is contemplating buying a Whirlpool washer machine.

Overall, I am happy with my Cabrio BUT we purchased a Whirlpool WTW7000DW0 Cabrio top loading washer w/ electronic touch panel in May 2016. We experienced water hammer from day one. I finally had enough yesterday and knowing that the plumbing could be suffering (15 year old condo), purchased 2 Sioux Chief MiniRester, Model 660-H arresters (Lowes at $9.99 each) and had a plumber install them today. I could have but am nursing a fractured rib. Long story short, they work perfectly. There is NO indication elsewhere in the unit that water is even entering the tub unless youre standing right beside it.Ive been told that hammer problems exist in ALL high efficiency washers, all are prone to this problem. I was also told by a Whirlpool support person that the Cabrio is a Samsung design and the pulsing of supply water off and on, over and over is normal operation. If I had been informed when purchasing that hammer is a common problem, I would have installed arresters from the get-go. At the very least, manufacturers should include arresters as a part of the sale; installers should make sure that every new installation includes arresters. All told, I am out just under $200.00 for new technology that really could have been engineered out in the beginning.

Not enough water to separate/agitate the clothes, so theyre as dirty coming out as going in. We bought an older washer that takes on more water and, presto....clean. We bought new Whirlpool for over $500.00 & sold it for $150.00.

After much frustration and disappointment, as well as 2 huge repair bills with my front loading washing machine I sent it off to the scrap yard, still looking brand new, and went back to a top loading machine. I purchased a Whirlpool top loading, high efficiency, low water machine. I have had it for almost 2 years now and am extremely happy with it. I would highly recommend it. Fairly quiet and easy to use and takes very little detergent. It does not have an agitator so it is gentle on clothes. I know some users have complained about tangled clothes but, in my opinion, if it is loaded correctly this should not be a problem.

I purchased this machine about a year ago and it is the biggest piece of garbage on the planet. The biggest problem is that it will not spin if the load is even slightly unbalanced. It does not clean the clothes. If you try to rebalance and spin the load, it adds more water and then gets stuck in a cycle where it drains and adds water forever. Do not buy one of these. I am finally surrendering and buying a different machine. A total waste of money.

I purchased a Whirlpool Washer/Dryer set in June 2014. Yesterday, Sept 9, the motor stopped working. The machine was on but nothing happened. Called the repairman who said the motor burned out and had to be replaced at a cost of $180 plus $75 for his labor. I paid around $400 for it a little over a year ago and now I have to pay $255 to get it repaired which is ridiculous for a ONE YEAR OLD machine. I will never buy Whirlpool again. I should have read the reviews first before buying but I always thought this was a good brand. Lesson learned, never buy Whirlpool.

I bought in 2008 a Whirlpool Cabrio washer because it was the best. It cost me $900 plus 170 extended warranty for four years.This month, my washer showed an f1 code. I call the Maytag store and guess what, they are not there anymore. They closed the store. I called for my extended warranty and guess what, they are not with Maytag and they filed a chapter 7. So, I spent over $1000 in a machine that only worked three years and now I have to buy another just because no one wants to take the responsibility on the warranty. I have to pay another $300 to fix the problem and even doing that, theres no guarantee that it wont fail again. So, and this is to the people of Maytag and their cheats, you may take my money but you lose me as a customer forever. Thank you for nothing. I will keep that in mind next week when Ill be in the store buying another washer.

The washing machine has been through 4 boots. The boot material is so flimsy, that they tear constantly causing water to leak out of the machine. There are times it is minimum water, and other times a lot of water.

I bought this nightmare machine one year ago, and stop working. If I try to program a cycle it put itself lock so I can not use or program any cycle. I can not open the door and start a noise like it was draining without clothes at all. And when finally it ends, the machine is like dead, no works, no programs no nothing. I am sick of this appliance. It is almost new and just does not work as it should be. But the worst is customer service, OMG. They lie about everything. The technician came to see what was the problem and told me it was the card, so he could not do anything until the factory send the piece to the place where I live. Well this happened one month ago and I am still waiting for the service. My guarantee was still on time, but every day at customer service they have a excuse/lie that the piece is on my way and service will be completed. Well I am still waiting and nothing happens. I am desperate. No one cares about the customer. If I would have known or read the bad reviews about these washing machines I would have never bought it. I got it at Walmart. I regret deeply. I do not know where or what else to do. Nobody cares or listen. Shame on you Whirlpool.

I purchased a Cabrio washing machine and discovered multiple repair issues over the last few months. I have had to replace a pump for $85 and now the machine will not complete a cycle. I found out the the whole thing is rusted above the barrel which is causing a leak in the back and leaving our floors covered in rust shavings. From my research and reading others reviews and issues, they pay for a serviceman to come out and still it does not solve the problem. My husband is a student in college and we are living off student loans. We bought this machine because we trusted that a Whirlpool would last and be a good investment. I am very displeased on this machine and doubt I will ever put my trust in Whirlpool again. I called to complain and got the typical response I have read others got. I am not paying for a service call when it will not fix the washer in the end. I plan to file complaint after complaint and encourage any class action suit against Whirlpool for producing a poor washing machine and misadvertisement on this machine. I will move forward in this. I feel that as consumers we have a right and should have a sense of ease when you spend $900 on a product that it should work and not give out as it has so quickly. If there has been multiple people with common complaints, then there should be a recall on this washing machine.

Whirpool Cabrio Washer - Do not buy this washer. Clothes are not clean. They are twisted with residue still trapped in the wadded up mess. Even if you select deep water clean, your clothes will still have the same dirty marks on them as when they went in. Also, there is no spin cycle. If youve got a bunch of wet towels you just want to spin the water out, you can forget it. You will have to do a complete wash. And the 1 star is not even appropriate but there is no choice of a big fat zero. Wasted a lot of money on this when Ive had great luck with Kenmore.

We bought a Whirlpool Cabrio washing machine a year and a half ago. It started making loud noises over time and finally stopped. Whirlpool did advise us that it was out of warranty but suggested they send a factory repairperson out. They told us depending on the problem they might pay the bill. It turned out that a nut holding the pulley had not been tightened up properly at the factory and had no restraining device, so it simply rattled off over time. Since we dont use the machine that much, the problem went past the 1-year warranty. It cost us two hundred and fourteen dollars for repairs. I could have put the nut back on myself for free. The service guy also said they had multiple similar problems and I should contact Whirlpool and they would probably work with me. No chance. They only kept repeating that it was out of warranty. I even talked with a supervisor who said the same thing. I asked to appeal further and she refused to give me anyone else I could contact. I asked for their legal department information, and she said she did not have that and I would have to get that through my attorney. What a joke. No more Whirlpool for me.

Ive had trouble with my washing machine since the end of May 2011. I have had over 5 service/repair calls which still resulted with the same problem. By the way, I do have a warranty on this product (which hasnt seem to have helped at all). I have never had such poor customer service in my life as I have had from Sears and can assure you, I will never buy another product from Sears or Whirlpool considering the experience I have had. I have missed numerous days at work only to wait for a repair appointment that never happened. Needless to say, I am very disappointed and would not recommend anyone to buy from Sears or Whirlpool.

My husband and I purchased a Whirlpool Washing Machine & Dryer a year and a half ago. As of current, the machine has stopped working. The machine will turn on but will not agitate. It makes a horrible grinding noise. The type of washer we purchased was a WTW4900BW0. Whirlpool told us we should have purchased the extended warranty. But, I feel we should get more than a year and a half out of a machine that cost $650.

After owning the highly recommended Cabrio for only 2 years, I was told it would cost $300 for the motherboard!! I have always used Whirlpool but this machine is terrible. Water saving is not an option when washing clothes. Unless I use the bulky cycle, my clothes come out dry and smell dirty.

Im happy with my 9 year old purchase. They are front loaders and they sit too low for my comfort. The available pedestals cost hundreds of dollars for a pair...that I do not want to spend. I have not had any repairs needed.

My Whirlpool Cabrio Washer is less than one year old and quit working. Sears was supposed to come out and fix it (I even have the extended warranty till 2014). Service never showed up; when we called, they told us we had been rescheduled. Here it is the rescheduled day time slot and they still have not arrived. Im getting the runaround from them and I am supposed to be grateful because they gave me a $75 gift card for my inconvenience. Im on hold with Whirlpool because I just want them to take the washer back. I have been told by Sears since it is over 90 days, they cannot refund my money. I just have to wait for a repair which may or may not happen since they may not have the parts. This is unsatisfactory service from both Sears and Whirlpool. I have always bought my appliances through Sears and they have always been Whirlpool. I wish I would have read all these reviews before I purchased this model.

I agree with all the unsatisfied customers with the Whirlpool Cabrio! Clothes do not come out clean! I called Whirlpool also and was told to be sure to place my clothes around the sides of the tub, which I always did. If Whirlpool was smart, they would take the complaints about the Cabrio and offer the customers a small amount of money towards purchasing another Whirlpool washer. I know I would have appreciated that. Instead Ill go out and buy another washer and not a Whirlpool. Even my kids dont want this washer and its practically new!

I purchased this washer two months ago and have been greatly disappointed with it. I put in a large load on wash cycle, but the rinse cycle is barely any water, and is all soapy water, so then I have to turn it back to wash cycle to get more water and then back to rinse to finish it properly. I was never told about the short water cycle, why not? It is still under warranty, but said I have to deal with Whirlpool, and all they can do is send a repairman out and if it is not a defect, it will cost me $130.00 for the service.

I bought my Whirlpool Cabrio Washing Machine in 2010. I hate it 100%. I have never used bleach in the machine. I use liquid detergent only. 2 things happen every day: #1: When I wash a load of colors, I take them out when complete and there is dry white powder like substance over the black clothes. It looks dirty but it just got washed. #2 About once a week, I will pull something out of the washer and there is a bleach spot on it. The last item that this happened to was a $200 sweater. It went in the garbage. This should never of happened with an $800 washing machine.

I dont know who is the bigger idiot. The designer of this washer or me for not reading the countless bad reviews. I bought a Whirlpool 4.3 CU FT TL WTW5000DW machine on 7/19/2015. It does not come close to cleaning clothes. It now takes me three times longer to do laundry because I have to check every piece of clothing for any stains. These are minor stains mind you but, they will not come out unless I use something like Spray and Wash. My time is valuable, maybe I should drag my clothes to the river and beat them on a rock. Very disappointed.

Hi team, I have to lodge this complaint after because of getting continuous problems I have suffered with my Whirlpool fully automatic washing machine top load 11 kg bloom wash 360 degree. I purchased the abovesaid brand new washing machine on 1st Jan 2017. Since the purchase I am struggling with this machine. I raised the fault in the beginning itself and the service was done on 5th of Feb. Jobs sheets enclosed here with.Similar issues kept on arising and whenever I raised those issues with the whirlpool team, they mentioned that company policy is to repair the faulty part if it’s in warranty and they will not replace. They suggested me to go for the AMC and to be on the safer side, I also took AMC under warranty period only. (AMC card - My cheque dates and service details all are mentioned onto it.) Recently I faced another issue on 26th Feb for which ticket was raised. Engineer visited on 27th Feb and advised us to replace the motor part. On 3rd March they replaced motor mechanism and ball-bearings. Then engineer advised us to check the working by giving a trial wash.I started the machine to wash clothes and after 20 mins machine started making abnormal noise. (I have made video of it, audio of the video captured the noise). I again called up the service engineer immediately and informed him about the voice coming out of machine and he gave a lame answer by saying “It is normal sound”. Then I again called Whirlpool and requested senior engineer visit to resolve the issue. Senior engineer visited and told us that one of motor screw wasn’t tighten properly. It opened while running the machine which completely damaged the motor.After that I am continuously calling to service centre to get the updates on my machine motor replacement. Finally they mentioned that they dont have motor part available with them due to company ceased this model productivity. When I raised this issue with the Whirlpool team they mentioned that they can only pay 40% of the machine value, because I had AMC. However, I did mention that this damage is caused by the negligence of their service engineer, but they didn’t discuss anything about it.When I continuously chased them they dropped me an email to refund only the 40% of the machine value. I feel cheated and harassed!! When I bought the machine they gave us 10 years warranty now they mention that motor is not available as it’s a 5 years old model. My grievance is that since I had already taken the AMC and the damage was also caused by their engineer, why I have to bear the loss. I have already struggled a lot with this machine since last 5 years from the day I bought this machine and now I am losing my hard earned money. Kindly do the needful. Documents attached as follows: 1. Serial number of this machine 2. Bill/ Invoice copy from dealer 3. Job sheets4. AMC card (with 3 years extended warranty) Thanks,Pratibha

On the 27th March 2012 I bought a new Whirlpool 6th Sense washing machine S/N 411048002028 AWOE 9210 - 30 9Kg for E499.00. I brought it home and plumbed it adding in a lime filter on the water line to protect it from limescale. On the 14th September 2016 a service technician replaced the entire drum as the old one made so much noise and the ball bearings are part of the drum. On the 7th June 2013 a technician replaced the drive belt claiming that it moved if a light load was put into the machine. On the same day I added an extension of 3 years Guarantee at Euro 89.00. On the 14th October 2013 a technician examined the machine for a water leak but found nothing and charged me for the call. Out E25.00. I lived with the noise of the spin cycle ever since. The noise got steadily worse until 27th September 2016 when the machine finally packed in. I stripped the machine down to find the ball bearings on the drum completely rusted over so the drum was rotating without the cushioning. On the same day I bought a Bosch machine and decided to forget about the extra guarantee as the offending parts had already been replaced once and did not even last 4 years. I will bring it to the recycling yard later today as that is all it is good for. It was bought in Media World, Orio Center, Bergamo. It was paid for by Gianni ** who is my father-in-law and had a loyalty card for the shop.

Whirlpool cabrio top load washing machine sounded like a jet engine taking off on spin cycle then started spewing grease on the floor. Called hotline with make mod ser #. Repairman came out 5 days later. OOPS! Whirlpool made a mistake, repairs not covered. Please pay repairman $450. Should have had him make the repairs then threw him out of my house.

The features on the washer is a wider size wash basket, no non-snag agitator with 5 load size choices, 5 water temperature choices, type of wash includes soak, quick wash, normal, deep water, heavy duty, bulky, hand wash, gentle, some other choices Along with a choice to wash your machine, one rinse or two rinses without fabric softener, one rinse or two rinses with fabric softener. And finally a selection for Pre-soak on or off. Also has a 3 light display for what it’s doing, lid lock, pause, cancel and start button. It’s an HE. Clothes come clean.

I purchased Whirlpool front load washing machine (Sport 1072 CB) in March 2013 and since then it has been my worst nightmare. Buying a Whirlpool washing machine was one of the worst decisions I took. The problems started to come from the first month itself. Many parts have changed and are still being done. I am continuously requesting them to replace the machine but they have decided not to listen. The after sale service of Whirlpool is the worst in the industry.

Whirlpool Duet Steam Front Loading Washer Model #WFW9750WW01 - The washer is only 5 years old and sounds like the space shuttle landing while in the spin cycle. Cost to repair parts only will be $896.87. The bearings among other parts are shot. I will NEVER own another Whirlpool appliance under any circumstance. Angry is putting it lightly!!!

I purchase this machine over 15 years ago. It’s still working, washes the clothes. The only problem the section where the bleach is poured is completely rusted out. The machine has definitely lasted beyond the 15-year cycle. I intend to purchase a new one. I probably would buy the same brand.

Why would I, and others buy Whirlpool made washers, with all of these service problems? Now I understand why they have profit/loss statement problems, and stock prices in the pits.

The repairman said the shaft, which of course is one piece with the outer drum, is corroded. Really? Did we not expect water in our washing machine? The repair is $500. After reading all the bazillion complaints on this model (on the internet), I have decided not to repair the piece of junk!

Buyer beware! I purchased a Whirlpool Cabrico topload and with my second wash, I realized I had a mess of a new washer. Ive called the call center on 3 separate occasions and I have spoken to other customers who have the sample complaint. The clothes are not washed clean. They have a residue left on them. My advice to all potential buyers, dont even consider buying a Whirlpool Cabrio washer. It is the worst purchase I ever made in an appliance. Im very unhappy with my washer.

We purchased our Duet in July 2010. It worked great until two weeks ago when the washer sounded like a 40-year-old washer. The bearing sounds like an extremely high-pitched “wrr”. We can hear it in the back of the house. I looked online to get parts and noticed that you cannot replace the bearing. You must replace the entire rear drum ($358.00). This does not include the labor. I talked with a technician, and they said the whole drum must be removed, not a one-man job, and to take the whole thing apart. Now, theres no price for installation. Lets go low ($200.00). Probably more. I cannot get a price nailed down without a visit. Now add those together ($558.00), I could put almost $600.00 into a washer that this could happen to in another 2 years. Wow.We had a washer that lasted us 15 years without any parts. Is there anything that you can do to help me? This is totally outrageous. Please help. Thank you. This was part of my chat to Whirlpool. Whirlpools response was I understand your problem but cannot help you. It is out of warranty. No help, no discount, nothing. I will and have all my friends never to purchase Whirlpool. This is from a so-called American company. Im very disappointed.

It was time to put the old Frigidaire Washer out to pasture. I researched for quite some time online to find just the right new one. Its all so confusing as they all claim to be the best. The Whirlpool WTW500DW Top Load is the one I chose to look at along with 2 comparable others. I have had Whirlpool appliances in the past and was always happy with them, so I will be honest, I was leaning towards Whirlpool. I purchased the WTW500DW and matching Dryer after looking at the 2 others first. Price was lower, features were more to my liking and better quality/sturdiness was very apparent to me. This was the lower priced machine out of the 3 but had everything I wanted and a little more. The HUGE wash basket is wonderful. I have literally cut our laundry down from 4-5 loads a week to 2! Our clothes have truly never been cleaner.I am amazed at the great job this machine does with a minimum amount of time and water. It is quiet, efficient and the cycles do what they are supposed to do. The absence of electronic pad buttons is greatly appreciated. Its standard dials are easy to read and set. In my opinion, Whirlpool has done it again. Its a great Washing Machine at a price that is lower than others without as many nice features, it is well built and does the job perfectly.

As I write this my Whirlpool is roaring because a bearing is probably going bad. Ive owned this washer for maybe 5 years. They designed this washer poorly. If you leave change in your pocket as everyone does then it will end up in the bottom below the basket and get trapped. And it dislodges, and it will, when the drain pump engages it will blow the coin through and it will break the plastic housing. It needs two beads so that NO COINS can get through if you wash them. Very disappointed customer.

Cabrio washer - What a piece of junk! My washer is 2 years old, it now does its own thing - stopping when it wants, doesnt finish cycle, beeps finished and the clothes are so wet and the washer is not emptied. Then, I put it on drain and spin. One time, it kept going for almost an hour of off and on. My clothes were so out of shape and that was on low spin. I finally took them out and put them outside. The clothes from day one have always come out so wrinkled and that too is on low spin. Im afraid to use high spin. I know you have to for towels, but it still does not drain. It shuts off and on when it feels like it. My first contact with Whirlpool was, Well, did you buy the extended warranty? I hate it when asked that when purchasing any product. Its like saying, This is a piece of crap. Im warning you now so buy the extended. So right there, I felt Whirlpool isnt willing to help. What else can we all do here? Please advise.

I purchased the Whirlpool Cabrio about five years ago. Last year, the motherboard had to be replaced. This year, it started load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $100 to have someone look at it, and was going to cost almost $400 to repair, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. Do I have Stupid tattooed on my forehead? I will never buy a Whirlpool again!!!

We purchased our Whirlpool Duet model WFW9150WW01 13 months ago. The warranty was up at the one year mark. We chose not to purchase the extended service plan. After all, a washer should last at least five years right? Wrong! The front seal has gone bad. It is an $85 part plus shipping, plus hours of my time. So, I purchased a product that is supposed to conserve water and instead I am having to purchase a petroleum-based product (the rubber seal), as it would seem, every year or so! These companies have us snowed with the whole conservation bull! CFLs, High Effeciency, Bio Fuels, etc., its all a hoax! And it is a hoax at our expense. Does anyone just produce a good product anymore? Oh yeah, I forgot... Japan does! Our economy continues to go to hell while other countries are coming online. Get your act together, guys, before we lose everything!

We bought a Whirlpool washer in 2010. It started making a loud noise on the rinse cycle in 2012. We called Whirlpool. They sent out a repairman from A and E Repair. Was told tub bearing shot, repair over $700.00. Contacted Whirlpool, was told machine out of warranty. After talking to them, they agreed to send parts if we paid labor. Machine lasted less than a year making the same sound again. A and E sent out same thing, bearing gone. Repair cost $997.17, charged us $136.74 service call after 2 minutes to shake the drum and saying same problem. Was told by Whirlpool, no warranty, tough luck.

I purchased a washing machine in year 2002. It was working perfectly. Recently, its drive belt started slipping. I called local service center, S. R. Enterprises, with mobile number 9204792391.The technician came after 3 days and declared that the gear box is leaking and will have to be replaced. They had no gearbox in stock for model f45, top loading, fully automatic.After a wait, they took away the machine to their workshop on 30.09.2011 and returned it on 04.10.2011.They charged me Rs. 4,730. I will have to be replaced. I found that its LID, which was perfectly okay, is now making a terrible sound when opened and would fall down, not allowing to load the machine. I informed the service center immediately. After many reminders, a man turned up yesterday and declared that the LID will have to be replaced and I will have to pay Rs. 2,000 for that. I rang up the service center to say, Since it has been damaged in your workshop, you should replace it free of cost to me. Their reply was evasive and negative. I called your call center and they registered my complaint - customer number **, comp. number **. I was assured that the LID will be replaced within 24 hours.

I am writing this complaint because of the very poor service of Whirlpool. My washing machine broke after 1 year of use. Luckily, I was on my 2-year insurance. The wiring fully collapsed and I needed to change the whole drum. I called Whirlpools customer service and they said that they would fix the problem after 2 weeks. They came on the day and found out the problem and ordered a new drum. They said they would fix it up on the 5th of December, and it has already been over 3 weeks. On the 4th of December, Whirlpool called me and said that the item they had ordered for me has been damaged. I am not satisfied by these products because it is only a drum (it cant break that easily). I cannot recommend this company to my friends and family due to the quality of the products and the poor customer service as I was waiting on the phone for almost an hour trying to get through.

Reliability. I have bought Whirlpool used and new and they have been the best washers that last so much longer than other brands. They also have more than enough settings to truly take care of everything in your home that can be washed.

In 2009 I bought 2 (yes 2) machines (one was for our daughter). I also took out 5 year warranties on both (good job I did). Within the first month on our machine the paddles flew off and after a bit of a debate with the insurers we had another machine (same model). Within a short period from date of purchase both machines had a number of faults - circuit boards, weights that came loose! and bearings going. There are other bits but too extensive to list. To be fair to the insurers they were no trouble (it really is the inconvenience of being without a washer and having to schedule time to get it sorted out). I will never ever buy a Whirlpool as all of these (3 in total) have been a nightmare and ours is sounding noisy again (it only had a new drum 12 months ago for bearings - yes you need a new drum for that £200 in all!!) so I am really glad that we have the insurance. When that runs out and the machine is dead (whichever comes first) I think we will will be buying either a Beko or a Samsung that are getting really high ratings. Anyone reading this might wonder why did we buy these in the first place. Well a colleague of mine at work had one and said it was fantastic (she had children so used hers a lot) hence me buying them (and they were not cheap by any means, so thought we were getting a cracking pair of machines....cracking, yes they might as well be as a chocolate fireguard has more reliability...WARNING DO NOT BUY A WHIRLPOOL WASHING MACHINE - IT COULD DAMAGE YOUR SANITY! AND FAITH IN HUMAN BEINGS TOO!!!!!

We purchased a Whirlpool Cabrio washer brand new from Lowes. It did great for about 6 months when a terrible grinding noise started. Then it also would not spin dry the clothes - they would come out completely soaked. Repair guy came out and fixed it. Lasted for about 1 year - same thing again. Lasted about 1.5 years this time and now the loud grinding is back and my wife - who Ive heard cuss just a couple times in 20+ years - said, This ** thing sucks. The clothes are soaked. I cant stand this washing machine. So, Off we go to buy a new machine. Definitely not a Whirlpool though. Id give this machine 1 star because it does a decent job for a while but major repairs 3 times in five years is not what I deem an acceptable appliance.

On its 1st year, the water pump went out. It cost $200.00 to replace it. On its 2nd year, the circuit board went out, and it took $300.00+ to replace it. On its 5th year, the bearings went out and cost $250.00 to replace it. I bought this for $900.00, and I already have paid $750.00 plus the price of purchase which makes this washer $1,600.00. Whirlpool should compensate all of us who have worked hard and have purchased this product! I will never purchase from Whirlpool again. I can’t afford them. I should get a refund from Whirlpool. Don’t they care? Email me for these problems at **. I am so dissatisfied with this product.

I bought a pair front loading washer & Dryer May this year and took Delivery in June. First problem was with touch controls. I should have Known then it would be trouble, they replaced it then we went home to Fl. - Aug. Returned in Oct - used the machine eight times total and it locked up with our Clothes inside in water. Called for service, was told it would be a week before someone could come, then was told after four days it was the mother Board and it would take at least another week to get our clothes out. Their Service is the worst I ever have dealt with. The whole house - we Bought Whirlpool based on the Maytags we bought for our House in 2004. Never a problem but those Maytags were Maytag - not whirlpool. I would never buy any Whirlpool Appliances again. It is sad because I try to buy American made to support our fellow Brothers and sisters in the work Force but now I will buy made anywhere as long as it works and has reasonable service. Whirlpool is not the same as I Remember from years ago.

Whirlpool Cabrio Platinum WTW8500BWO - It doesnt wash anything very well. I hate it. Dont want it. Wish I didnt buy it. I do all kinds and sizes of loads. My clothes come out dirty - I have to wash my clothes 2 or 3 times.

My washer worked less than a year. I finally called Whirlpool and they basically said, were a big company and you must for the rusty, broken drive shaft, pay for all new computer face plate, and service repair. I contacted the FTC and they told me they needed more complaints in order to make them do a recall on Cabrios. Good luck!

I purchased my washer about 1 month ago and I used daily. I went away for the weekend, and now it does not work. Washer will not wash, fill or spin, gives a LF error. All lines have been checked. I need to call service.

A total loss of money. Does not use enough water to clean clothes. Gets out of balance all the time. Do not buy.

My Whirlpool Cabrio cannot wash sheets, blankets or any of this size. It balls up in the middle and form a bubble and only part of the items is washed and washing powders are trapped. I have purchased more sheets in the past 4 years than I have in the past 45 years of doing laundry, because the washing powders are not washed out. I wash on second rinse also, never fails and it still does not get all of it out. The clothing gets off balance if it was more than 3 small items. I have a leveling tool that I put on it often to make sure it is level. It’s something within the machine. I will never, never, never purchase any more Sears’ product. If anyone has jury-rigged this machine to work, please let me know. Sears has refused to help me, even today.