I purchased by first Whirlpool Cabrio washer in 2007 with an extended warranty (my husband did not want me to buy). Thank goodness I did. The machine had repeated issues to the point that the service repairman and I were on first name basis. Finally, the mother board went out. The rust on the sides was excessive and of course my expensive sheets and towels were being shredded. Lowe’s extended warranty plan did honor this and replaced my machine with a new Cabrio washer (big mistake!). The new machine; receipt for this was over $1,600.00, including the new extended warranty that ends in 2014, was bought on 3-25-09. It now requires a new drum and bearings which are being replaced today (9-19-12); however, the corrosion is just as bad and my clothes are still being shredded. Oh, also the lid no longer locks and to get the machine to actually run. I have to physically hold down the lid until the lid locks. The repairman said that there is nothing he can do as the company will not repair this or replace the machine again under warranty! The joints where the lid attaches have rusted through and that is why the lid cant lock. The whole lid needs to be replaced and the company says it would cost about the same as a new machine about $690.00. What a rip-off this company is for the consumer! I will never, ever deal with Whirlpool again and I mean never, ever again! (sans Taylor Swift)!

What happened to the Whirlpool Corporation that we grew up with? I purchased a Cabrio Washer on 8-29-11. Here it is, 4-24-13 and the transmission is shot. Two loads of clothes were ruined and sensors went bad. All in all, over $500 to repair it. I called the customer service line, what a joke - bad product and worse customer service. Not even and Im sorry. Well it is out from under warranty and when I buy something, I research it first, she said. Wow! Thanks Reena for all your care and concern. I dont know if Ill ever buy Whirlpool again.

I bought a Whirlpool Duet Washer and Dryer in September 2013 and washer is already broken. It leaks out the front of the front loading door (yes, I clean it as advised, including leaving door open to air dry etc). I am a retired senior citizen and my wife and I spend 6 months of the year in Florida so the washer has barely been used since we are barely home and its not like we are trying to wash load after load of heavily soiled items daily. I would not recommend this product at all!! The repair people said it would cost approximately $300 to fix and offered a plan to fix it for $350 with a 1 year warranty. Why should I bother to do either if I will have to do same after 1 year? This machine is barely used and broke?! The customer service people were not helpful and seemed only interested selling me the repair plan to fix what should not need fixing. So, to recap - I bought the machine in 9/13 then went to Florida from 10/13 to 4/14 (so it was used 1 month). Then, it was used from 4/14 until 10/14 (6 months). I returned from Florida this year in April 2015 and it started leaking in June 2015 (2 months). So, my machine has been used for a grand total of 9 months and it is already broken!!! Stay far away. Whirlpool should come and replace this machine for us for free if they care anything about customer service and senior citizens but clearly they do not. In Florida we have an old Sears Kenmore machine that has lasted for over 20 years!!

I bought a Whirlpool washer WTW4800XQ top loader. I have owned it for about two years and now it has tore up, the repair bill will cost almost what I paid for the washer. I feel it is bad business to sale something and it not last any longer than it has. No one should have to buy a washer every two years!!!! When it gets to the spin cycle it works fine and then all of a sudden it will beat and bang and if you dont get it stopped it will be in the middle of the floor. Im very upset and put out with Whirlpool!!!!

It is a top of the line washing machine. I have had it for almost four years. It is the best washing machine I have ever had. I have really enjoyed it, because; I am able to wash my comforters in this washing machine.

I just bought a Whirlpool Duet Front Loader, and it vibrates excessively and wont fully rinse out all of the detergent. I have to take the tray out each time and rinse. Also, it has a musty smell.Whirlpool sent a repairman out to replace the shocks on a washer that is less than 2 months old. The repairman told me to use less detergent, but I am only using a teaspoon of powder detergent which is recommended and using Affresh once a month. There is nothing they can do about it till it is deemed unrepairable.

Machine wont go through the whole wash cycle., Wash, Rinse, Spin. It stops and shows an error message and then I have to keep rearranging contents, over and over. This is worse if you try to wash a small load.

My NEW Machine Top loader HUGE drum. Have problems with clothes not looking like they’ve even been washed, Spun so hard they are twisted all to heck. And white stuff - my oxy powder maybe? Not dissolved. My old machine was a Kenmore 30 yrs old. Thought I’d be able to trust whirlpool but not sure. Am I missing something in the loading process. Seems to read something bout not Covering the knob on the bottom. Is this true?

We purchased a Whirlpool washer model WTW7500 in November of 2017. I found the clothes were not getting clean and also noticed that even after a full wash some parts of the clothing or sheets had dry spots! I checked all connections and called for service. As soon as the serviceman saw the machine he said, “yes, that’s a problem with those machines”. They are low water/water saving as per some American regulation and that’s what happens... you’re going to have to live with it. He also suggested running an extra rinse and using “deep water” function. I did this and it made very little difference except now a wash cycle for bedding is 104 minutes! Also, still had a big dry spot on my sheets!When I called again to Whirlpool they scheduled another repairman for a second opinion, turned out to be the same person with the same answers... I called Whirlpool again and was informed that my washing machine is working as designed! I argued that a washing machine is designed to wash and clean clothes so this one does not do what it is designed for... I spoke to the supervisor, she was actually just rude, also said I not had 30 days to make a complaint and I was outside of that, when I asked to speak to her supervisor she said there was no one above her although she denied being the owner of Whirlpool! (That’s my little joke). Anyway wish someone had warned me prior to this purchase.

I bought a Whirlpool 3.4 Cu Ft. Top Load Washer, Model: WTW4800XQ on Sunday. Today is Tuesday morning, but the machine broke last night. It lasted for about 5 loads and they were not big loads, unbalanced, and yes I had the right amount of soap. Whirlpool is saying that I washed something that was not machine washable. However, that is simply not true. I washed the bathroom rugs (which have been washed many times before) and they are saying the pump is clogged. If I had a washing machine 48 hours ago, do I really have to pay a service repairman to fix it? I will never buy any Whirlpool product again.

After happily using Maytag washers at my old address for 30 some years, I moved to my current address and in 2006 I purchased a new Maytag. In 2010 I needed service. I was advised it had a bad bearing and was not advised to repair as it would cost well over $600.00. I purchased a Whirlpool Cabrio top loading HE appliance.The Cabrio worked well until one day it made a horrible noise. Although it still worked, I called for service and was told it had a bad bearing and would cost $670.00 to fix and they advised against it. After the service call, it never worked again. I know things dont last like they used to but 4 years is ridiculous. I have been advised that Whirlpool bought Maytag. Is this what to expect from so called reputable companies?

I bought a new house 2.5 years ago with all new whirlpool appliances. This week Im told the washer transmission is defective. Unbelievable! I only wash 4 average loads per week. This is a problem I would expect in 8-10 years. I am going to replace the unit with another brand.

Its now Nov 8 and Ive been officially dealing with this issue since Sept 26. This washer was installed in a new home. After less than 10 loads, my washer stopped draining and I was left with a load of towel soup for over a week while waiting for a service call. I still have the same defective non functioning washer sitting in my home and have been unable to do laundry at home in all that time. So far Ive spoken with 2 customer service representatives. The first was incapable of scheduling a service call. She clearly did not understand how to operate the database used for scheduling. I was finally able to schedule appointment on my own but had to wait a week before the technician was able to come by. It was determined that either the latch mechanism or the mother board or both are defective from the factory.The second was just plain dismissive and completely unhelpful. I sat on hold for about an hour each time before getting to speak to a person. Ive also received two canned emails in response to my poor review of this washer on the Whirlpool website. They basically blame COVID for the delays and state the parts delivery should take 3-4 weeks. I was originally told 14 working days for delivery of the parts. We are already past both deadline with no end in sight. At this point, Id like the defective washer replaced rather than repaired. And for the record, this was a new washer (less that one month old) installed in a new house that now stinks to high heaven because slimy, scummy water that will not drain out has been there since September 26. Id really just like for someone at Whirlpool to honestly care about this and take a moment to address this issue.

I purchased a Whirlpool front loading washer from PC Richards in January of 2010. The warranty was only for one year (the washer was new, not used). The model # is WFW9050XW. Anyway, the washer had to be repaired by PC Richards twice in the first year I had it. Once because the belt that makes the washer spin broke, then because the pump got clogged. Unfortunately, when you wash your clothes, your socks and underwear can get sucked into the pump. After that warranty expired, I purchased a warranty from my utilities company (PSE&G). I have had to contact them four times for repairs to this machine. The most recent problem is my clothes are still wet after the washer stops. I actually have to wring them out by hand to get the excess water out. When I contacted my utilities company about servicing the washer, I was informed that if the repair is more than the washer is worth they dont have to fix it. I canceled the repair and now got to the laundrymat. I figured if I wait until the end of the year, maybe the repairs wont seem excessive. I contacted Whirlpool about the problems and was informed that I should have been using a garment bag to wash my socks and underwear in. More or less the person I spoke with made it seem as though it was my fault the machine sucked up my underwear and socks. I, on the other hand, disagreed with her. I told her the washer should have been build so that it would not suck up these items. I was so totally pissed off I ended the conversation. I also informed her that I would not be purchasing any other appliances manufactured by Whirlpool or Maytag as they are affiliated. They obviously have no integrity when it comes to their product. However, I am totally baffled. Why do the Maytag machines work better and last longer than the Whirlpool machines? The washer I replaced was a Maytag. I had that machine for 17 years!!!!

I purchased my Cabrio a little over three years ago. Within the first month, the computer board had to be replaced and the tech informed me that it was not a malfunction in the unit; rather, it was because I did not have a sock bag for my socks and panties. I replaced the board, bought a sock bag and had no problems for about 1.5 years. A little over a year ago, the un-level started. I did research and found that I needed to replace the rods and add couplers as they were not thought of when the unit was created. This worked for an entire month. Now, I am in the same position again. It takes about 6 tries per load and the amount of water I am using is increasing with each failed attempt to wash. There should be a recall on this product. I notice there are many other complaints that match my frustrations exactly.

We wanted the ease of use and longevity of a top loader WITHOUT a full touch screen. Whirlpool has such units in a choice of price levels to accommodate most everybody. The agitator free design and automatic water level feature is amazing. Clothes are nice and clean and uses about the same amount of water as flushing a toilet.

We get the error code F1 in the start of the cycle and when there is 21 minutes left, we have to stop and reset at least 7 times before the water fills. We put a new sensor in for over $200. The second problem is it goes off balance no matter what the load is. I was going to have it fixed (if possible). After reading all the above I wont waste any more money on it and go buy an old fashioned reliable washer. What a piece of money sucking machine especially when I dont have any extra money to waste down the drain. I wish I knew before. There are a lot of people this time of year I would have rather given the money for a needy cause. How disappointed we are with Whirlpool!

We purchased this washer in April two years ago. I have had service people out twice to replace the lid. Tonight, my husband comes into the kitchen with chunks of something that I could not readily identify. He tells me the entire frame holding the light has rusted out and that the light is hanging into the tub! I followed him into our air conditioned interior laundry room and placed my hand under the rim. It’s filled with rust and the light is dangling down into the tub!

I purchase newly Whirlpool washing machine but it was not working from the first day of my purchase. So many service Engineer came but nobody can solve the problem, so I suggest to all please don’t buy washing machine from Whirlpool. I am very disappointed from this company.

Whirlpool Cabrio Washer - A total waste of money. My clothes are never clean. The low water system is rubbish. It doesnt work! Check out my pictures below. That is the result of a 63 minutes wash cycle. Dont buy this piece of crap.

My washer worked less than a year. I finally called Whirlpool and they basically said, were a big company and you must for the rusty, broken drive shaft, pay for all new computer face plate, and service repair. I contacted the FTC and they told me they needed more complaints in order to make them do a recall on Cabrios. Good luck!

We purchased a Whirlpool Cabrio, top load washing machine WTW6600SW back in 11/07. Last week (todays date is 8/19/11), the machine sounded like a plane taking off when it spins out. When the local service technician came out this week, he said that the bearings are shot. Since the tub and bearings are all one part, we were told by the technician that the part and labor costs would be $379.99 to repair it. We originally paid $799.00 for the Cabrio, less than four years ago. Whirlpool would not even give us a concession of a new tub and bearing part as it was out of the 1 year warranty.

Cabrio - In Dec 2013: Ran the Clean washer cycle and it would not cut off. I had to shut off manually. Called the company and they sent a technician, who said he fixed it and that everything was good. Fast forward to Feb 2015: Tried cleaning the washer again. When I left the house there were 10 minutes left in the cycle. When I arrived home 7 hrs later, the washer was still running and my hot water heater had cut off. I had to reset via the circuit breaker. This will be my last Whirlpool appliance for a long while.

Bought the Whirlpool Duet washing machine. It lasted around eight years. In the meantime I was replacing the rubber door seal cleaning out the pump constantly. The plastic pieces inside the drum all broke. Every few months I would get an error code. And During spin cycle it would literally shake my entire house. The problem with all the front loaders is the construction of the drum and the drum bracket. They are made of dissimilar materials. (Stainless and zinc) When you add soap to the water then the bracket becomes an anode and the drum becomes a cathode, which creates electrolysis which corrodes the bracket. When the bracket breaks your machine is totaled. I’m finished with every manufacture except Speed Queen. I bought a Top loader Speed Queen and I love it, it is built like a tank.

My husband and I purchased a Whirlpool Washing Machine & Dryer a year and a half ago. As of current, the machine has stopped working. The machine will turn on but will not agitate. It makes a horrible grinding noise. The type of washer we purchased was a WTW4900BW0. Whirlpool told us we should have purchased the extended warranty. But, I feel we should get more than a year and a half out of a machine that cost $650.

My 5-year-old Cabrio started coming up with error codes, and not draining and spinning the clothes. I called a week ago, they offered me 2 options, one being put $339 on a credit card and that would cover all parts, labor, and a 1 year extended warranty. They charged the credit card immediately for the biggest piece of crap washing machine. Someone came out 2 days later and told me he has worked on a lot of Cabrios but never one in quite that condition. I was led to believe that after charging the credit card, boxes would be arriving with parts to fix it. I called 2 days later to find out the status of when it would be repaired and they told me they already put a credit thru on the credit card because to fix it would be equal to the price of 2 brand new washing machines, and they will do nothing to honor that agreement. So I now have a piece of ** in my laundry room and takes me two days to do a load of laundry. DO NOT BUY THE CABRIO! In fact Im not going with a Whirlpool ever again!

I bought this Whirlpool Cabrio Top Load Washing Machine in December and have hated it ever since. The energy efficiency this item claims means that you will spend a ridiculous amount of time waiting for your load to finish. My family hates this machine and I regularly have to hear about how long the load is taking because the timer adjusts continually. Put in a QUICK load and it said 38 minutes, came back in 30 and it said 24 minutes. It is so frustrating!!! We are afraid to put anything on a heavy soil setting or anything other than quick, because it can take 2-3 hours to complete. I have to schedule a day to wash my bedding and there isnt any convenience in doing a quick load. I am going to have to sell this one and purchase another washer. What a loss!! This machine has been a time and money waster! I will NEVER BUY WHIRLPOOL again!!! I bought this machine through Best Buy.

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.

Its a great machine but the temperature control button is easily moved at times. The machine does a great job in washing clothes. Ive had mine for 10 years now and hope that I never have to replace it.

I bought a whirlpool washer because we thought it was the best. It does not clean our clothes especially my husbands jeans. They are on their third wash at this minute. I use Gain HE detergent. I bought clorox 2, I use spray & wash & I have even started using a little clorox but the red dirt still doesnt come out. I never had this problem with my old washer. If there is any help for me here please let me know. If this is supposed to be a water saver I dont see how I have saved any after washing jeans for the third time. If they are not clean this time, I guess he will wear them dirty.

I purchased a Whirlpool Duet washer in Jan. 2011 and there has been 3 problems. There has been water leaking, loud/banging noises during the spin cycle, and torn clothing. Technicians have visited 4 times in 7 months. At this point, I forsee more problems in the future. I spoke to a supervisor at Whirlpool and I asked if the washer could be exchanged. I was told, If it is repairable then we will continue to repair it. I was also told that I could purchase an additional 1 or 2 year warranty. A comment like that makes me believe that the company foresees problems in the future as well. A company like Whirlpool should realize that customers should not have to spend time leaving work early or taking off to meet with a technician about an appliance so often or at all! I have owned a washer in the past but it was left when we sold the home and I never experienced any problems!

We purchased our washer approximately six months ago. It is an energy-efficient top loader without a central agitator. If I wanted a washer just for lingerie then I would be satisfied. But I need a washer that will clean farm clothes. My husband works hard and his clothes show it. This washer does not clean them. I even tried putting very few items in at a time. They still arent clean. I have to take my heavily soiled laundry to the laundromat. My other main complaint is the baffling feature of a lock mode. I spend countless minutes standing by my washer waiting for it to unlock so I can toss in an extra item or add fabric softener, etc. When we removed the latch, the washer didnt work at all. Replaced the item at a cost of $40. Infuriating!

We have had our washer just over a year when the plastic hose that fills the detergent tray began leaking. The entire assembly is plastic and poor quality. Whirlpool customer service says since it is after 1 year, that I would need to pay for the parts & service ($489). I would not recommend this machine or anything Whirlpool.

Purchased Whirlpool clothes washer Cabrio Platinum about one year ago. Never sufficient water to clean items. Appears that there is no way to add additional water to ensure that items are cleaned. Many items come out dry and still soiled.

I bought washing machine Whirlpool Cabrio Model WTW7300XWO two years ago. It only lasted 2 years and the tub seal and tub bearing went bad. I called Whirlpool and they wouldnt replace defective part on their dime. I talked to supervisor and they still refused to admit they needed to fix this broken product on their dime and make it last longer than 2 years. They claimed only a 1-year warranty. This is totally unacceptable to have a supposedly good washer that you pay $700 for (manufacturer price $899) last only 2 years! Very, very disappointed! I wouldnt buy from this company again!

Purchased a Whirlpool Cabrio WTW7340XW2 washer approx 2 years ago. The machine runs so loud on the spin cycle you cant have a phone conversation or hear the TV over it and is leaking grease from the bottom. My mistake to not purchase the extended warranty but you would think a machine would last more than 2 years. I contacted Whirlpool online and by mail and they do not stand behind their product. I did contact a local repair shop and by our phone conversation was told it would be approx 300-350 to fix it and Im not putting that kind of money into a repair. Just want to let consumers know this machine is junk and spend your money on quality appliances, not Whirljunkpool.

On 12-22-13 we purchased a new Whirlpool Washer- Model=Top Loading-WTW4800BQ. We also purchased Lowes extended warranty. Washer was delivered on 12-24-13 around 1:00pm. Connected washer. Washer filled with water. System started but would not wash. 10 minutes later it rinsed and drained but would not go thru wash cycle. We clicked the cancel button for 3-seconds to restart. Same problem. Called Lowes - Lady name Kelly continued to tell us we did something wrong. She would not listen and continued to say its Christmas EVE. Finally the workers came out to check it out around 4:00. Confirmed washer is defective and new washer will be delivered on 12-26-13. Confused as to the label on the machine says made with pride in America. Our 20yr. old Cabrio only lasted two years and went up. Never buy another Whirlpool product!

I purchased my Cabrio Whirlpool washer five years ago. In the past two months I have had three service calls for repairs. I had water leaking out from underneath the machine which was the result of a failed drum seal. Now I get a ul message (there was one blouse being washed on delicate) and the washer is making a terrible banging sound. I dont think it is spinning. I have not been happy with this washer. My previous washer was 30 years old.

I was not impressed with the new HE washers but could not find any traditional ones anymore. I bought a Amana and am disgusted that it is only 3 years old and needs to be replaced because of a transmission problem with it not agitating. It costs more to repair than it is worth. As a consumer, I should be given a choice whether I want to upscale or be satisfied with older model features. I will never buy or recommend a Amana HE washer to anyone. My mother also has one, has had it for a year and it is already giving her problems. Shame on you Whirlpool.

The washing machine started leaking and making a noise like a freight train 6 months after purchasing it. We complained in February 2011, but the parts were not available until March 31, 2011. The same problem occurred in September 2011, and we are still waiting for the parts until October 18, 2011. In the mean time, I have been spending hundreds of dollars doing wash at the laundromat.

This washer is a piece of junk!! It doesnt use enough water to clean the clothes and now it wont spin them dry. I have maybe two loads a week on a regular basis. I have always used HE detergent. Never overload. It is only three years old and I have been having to go to the laundromat because I cant afford a service call and especially if it is what they say which costs almost much as the washer. Be ahead to buy a used washer or a cheap one. It wasnt getting the clothes spun out dry enough - dripping wet. Then it flashed od and ul and sd and f51 and then it kidnapped my clothes - couldnt get the door to unlock with the pause or power until I unplugged and still had to wait several minutes. They refuse to help. Do not buy this machine!!! The customer service was not one bit of help. Instead she wanted to charge me $350.00+ dollars for some plan.

I was excited to have an energy efficient washing machine and chose the Whirlpool Cabrio top loader. I truly wish I had read reviews rather than trust the salespersons advice. It does not clean clothes properly at all. They come out smelling dirty and are covered in white goo, even when the machine has just been cleaned. Stains never come out despite all of my efforts. Now I have water leaking out of the bottom as it fills. Not impressed at all. What a giant waste of money.

When I purchased my Cabrio washer 31/2 years ago I didnt bother to check reviews since Whirlpool was suppose to be the best of the best. An expensive lesson! A washer that spits out codes?!?! Whos got time for this? We paid 899.00 plus taxes for it, now we paid a repairman 99.00 to tell us its not worth fixing. He said the bearings were completely shot. As he was leaving he said his next service call was for the same type of washer! Whatever happened to appliances that last! Going green is all the rage but yet everything from cars to appliances is built to last only a short while. Judging by these reviews I cant believe Whirlpool didnt recall their garbage!

I have a Whirlpool Cabrio WTW5640XW and I was able to get the belt back onto the pulley, about a month back and it ran, loudly, but it ran. Last week the belt popped off again and now the pulleys are screwed, so I probably won’t buy another motor (for the sake of the pulley). Ill get a front loaded Kenmore or something as I was never completely happy with how this thing washed and (didnt dry) our clothes.

Very reliable and cleans clothes very well. I have used almost every machine on the market, and none compare. Very quiet and I use very little detergent and CLOTHES come out very clean every time. I am just very satisfied with my experience.

We have had this washer for a year and the longest it has run before breaking down is 3 weeks. Since it takes longer than that to get a repairman out to look at it and another 2 to 4 weeks to get parts, it has run less than half of the time we have owned it. This thing is a hunk of junk. Dont ever consider purchasing one of these lemons.

Ordered this two days after my son came home from college. He had to be out of his apartment July 31 2016 and brought 4 years worth of laundry with him. Monday my machine breaks, Tuesday I order this thing from Lowes Arrives at 2:30 on Thursday and as it is being installed I ask why the water fill is so slow. It is trickling out like a childs toy. Delivery man tells me the water is completely turned on. He hears this remark a lot from people who buy this model. I put in my first load of laundry, a small load of about 6 things that I am washing for my mother who is in a nursing home. They have that nursing home smell. I push pause as the machine is cleaning to unlock the lid and peek inside. Oh my God the clothes are sitting on top of each other not even covered in water. I then shut the lid and listen to the tiny slush of the machine agitating. At the end of the cycle they smell exactly the same. Dirty.I had read to use the deep fill so I rewash them on deep fill. Look inside halfway through and what do I see? Wet clothes piled on top of each other, still not floating in water. How are these clothes getting clean when they are in a wet pile on the bottom of the machine? I take them out. Still not clean. Not smelling quite as bad, but not smelling like soap. I then washed sheets, a blanket, and some clothing of my sons. Nothing smelled particularly dirty but NOTHING smelled like soap. The quilt was covered in hairs (my son and roommates had a dog) and soap residue. I had read this in reviews online also. I am wasting time since each load takes from 50 to 130 minutes (yes). I am wasting soap, oh but I am saving water - not really.Well Lowes has a 30 day return policy so I went down there and am expecting a GE machine with an agitator tomorrow, Saturday! Cant wait. The only one saving money are these manufacturers They no longer are spending cash on producing the agitator out of plastic, attaching it with nuts and bolts, or using gaskets between the parts. DO NOT BUY THIS PIECE OF JUNK, do not even look at it. I question all the HE machines at this point. You need to use HE soap cause you cant wash away suds in a machine with no water. What a con - the whole thing is.

It was time to put the old Frigidaire Washer out to pasture. I researched for quite some time online to find just the right new one. Its all so confusing as they all claim to be the best. The Whirlpool WTW500DW Top Load is the one I chose to look at along with 2 comparable others. I have had Whirlpool appliances in the past and was always happy with them, so I will be honest, I was leaning towards Whirlpool. I purchased the WTW500DW and matching Dryer after looking at the 2 others first. Price was lower, features were more to my liking and better quality/sturdiness was very apparent to me. This was the lower priced machine out of the 3 but had everything I wanted and a little more. The HUGE wash basket is wonderful. I have literally cut our laundry down from 4-5 loads a week to 2! Our clothes have truly never been cleaner.I am amazed at the great job this machine does with a minimum amount of time and water. It is quiet, efficient and the cycles do what they are supposed to do. The absence of electronic pad buttons is greatly appreciated. Its standard dials are easy to read and set. In my opinion, Whirlpool has done it again. Its a great Washing Machine at a price that is lower than others without as many nice features, it is well built and does the job perfectly.

This washing machine has been the worst machine I have ever owned - I have called Paddys Market on several occasions to have a repairman come out and take a look at this machine, which they did - but the machine never got any better - it has never ever washed my clothes properly its a piece of garbage - clothes come out dirtier than when they went in and sometimes come out dry. Its so busy trying to save water - it doesnt use hardly any - and forget doing bigger loads - I WILL NEVER BUY ANOTHER WHIRLPOOL product again.

My washing machine is just over a year old and it has ruined so many clothes... They come out with brown stains on them... Almost like a oily stain. Not sure where its coming from but its either Im gonna have to buy a different machine or keep buying clothes. My husbands t-shirts look terrible... If any suggestions to what it can be please respond back to me. Thanks. Model# wtw4815ewo. Serial# c51433710.

I just purchased this washer Whirlpool Cabrio. Im experiencing the worst with it because it seems to take forever for it to wash. I came to look at reviews to see if other people were having problems like me. My issue is when I put it on quick wash it seems to say 41min then to 56min then goes down again and up again. I feel like its using more water as many times I hear it filling and washing. I didnt see anyone complain on that part but for the price its a big headache and upsetting because I spent that much thinking you get what you pay but I rather have the old washer I had than this. If anyone has had this issue please let me know and was it an ongoing thing. Not sure if you can comment back to reviews but shame on them to see all these unhappy people and not trying to make things better for them. I wish I read reviews before getting it. Yes it looks good on the outside but is crap.

We relied on consumer reports as the primary source for a recommendation on this washer. Just under two years old, it started making a noise, which suddenly went away. Then one day the machine would not spin and drain, and we could not decipher the error code into anything useful. I turned the machine over to find that the drive belt was half-on/half off the pulley on the drive motor. This caused the belt to ride against the belt guard and wear right through it. I removed the belt and determined that the cause of the problem was that the large pulley on the drum was loose. For some reason the nut which holds that pulley on was slightly loose, causing the pulley to wobble. Not sure why they didnt use some Loctite on that nut. I put everything back together and tightened the nut. No problems and I checked it a month later, everything was still good. Fast forward to last week, when the machine was not yet 3 years old. Same thing, washer would not spin and drain. Tipped machine over to find that the belt had fallen off, the drum pulley was again loose. But this time the belt had damaged the pulley on the motor. I figured, no problem, just order a new pulley. Well you can buy just the pulley on the drum, but the pulley on the motor is part of the motor, it cannot be ordered by itself. The cheapest I could find the motor online was $250. We decided to cut our losses and buy a new machine. We will NEVER buy another Whirlpool appliance (or anyone elses by the same manufacturer, i.e. Maytag). Our last Kenmore washer lasted 23 years. Oh but it had an agitator and wasnt listed as HE (High Efficiency), so I suppose the environmentalists would get the dry heaves thinking about the impact of that washer on the environment. But it was useful for 23 years. Now this High Efficiency Whirlpool is headed for the recycling pile. Sorry, I think this hurts the environment more than an appliance which just works year after year. Yep, they took a design that worked and now we have energy/water efficient washers that dont last very long and are so expensive to repair that the solution is to just buy a new one.

Never again will I buy a Whirlpool product. I paid over $800 for a new washer 51/2 years ago. I had it worked on twice under extended warranty. Now the bearings are out of the tub and it sounds like a jet taking off when it spins. I had whirlpool products in the past and they lasted for years with no problems. I have a friend who has a relative who is an engineer for whirlpool and his job is to engineer their products so they fail within a certain time frame. They dont want them to last like they use to. They now have gotten their product line to the point where they can tell when it will fail. This is crap. What happened to products that lasted like they use to. NEVER BUY WHIRLPOOL.

Whirpool Product VMW TL WASHER with impeller absolutely is crap. I have it almost a year and it smells, and it noisy like a dog was in the machine and someone started it. Its off balance constantly. I hate it and will place on every blog the worst review I can write. Its a nightmare. It has a fake bleach dispenser a door but no holder underneath. Even the repairman thought the bleach went in the dispenser. My clothes were ruined along with sheets, etc on numerous washes. The bleach partially dispensed on dark clothes at least 8 washes.The washer was purchased at BrandsMart 11 months ago and so theres no returns.

I bought a new washer thinking I was upgrading. Wrong!! Well the new so called technology they put into these machines is overrated. They took a good thing and instead of advancing they have took two step backwards in time. I wish I had kept the old washer I had. I think I would rather use an old time wringer washer my great grandmother used. They are probably faster by hand. This new Whirlpool grabs every string on my hoodies and twist my clothes so tight in knots. I cant even remove my clothes until I fight and get mad enough to write a review. Whats up with these new washers?? Get rid of the slots on the Agitator!!

My family purchased a Whirlpool Cabrio washing machine approximately 4 years ago. The first two years were fine. I had no issues out of the machine at all. The last two years (just as my warranty expired) have been terrible. It was serviced twice just before the warranty was up and my husband has serviced it twice since. On two separate occasions, the bearings have worn-out and the bottom seal leaks water all over my floors. I would never recommend one of these machines to anyone!

We have had our Whirlpool Cabrio washer for quite a few years. I agree that the machine is a piece of garbage. Every load is unbalanced. You have to stand there when the spin cycle starts, with your finger on the pause button, so you can rebalance the load, which is no easy task. My 80 minute whitest whites cycle took 2 1/2 hours to complete. Thank goodness I started the load at 5:30am. I hate this washer and anytime I am in an appliance store and see someone looking at it, I inform them it is a piece of junk. I havent contacted Whirlpool because I know they wont help with any issues were having.

Purchased a Cabrio Top Loading Washer and Dryer 3 years ago from Lowes and our clothes have NEVER even come close to coming clean without spending a ton on stain removing aids, which only work part time. So I approached the salesperson at Lowes and I was informed (after the fact) that the Cabrio top loaders had poor ratings due to the fact the basket only spun 30 times a minute whereas the front loaders spun 300 times a minute. So after 3 years Im forced to bite the bullet and purchase another washer. Ever since they purchased Maytag, their quality control has gone down the crapper. Now Im going back to the old reliable, the agitator washer. Newer is not better in this case.

Oftentimes when we take out the dark loads there is a white line left. It appears to be detergent that does not go into suspension. We are using HD. Just lately we switch to liquid. Question in our minds is if it does not move the water enough to put the detergent in suspension, how in the world is it even cleaning? I do not see the turnover of the clothes. Where is the quality control with this?

We purchased a new Cabrio top loading washer in June of 2011 to replace a Maytag Neptune (thinking at the time that wed gone as low as possible). We didnt abuse the machine. In fact, because it had a tempered glass lid (in a plastic frame), we were careful with the lid on the machine. It broke during a wash cycle. Because its heavy, the lid has spring supports on both sides; these are stronger than the plastic frame and over time the frame will break, rendering the machine inoperable. The discounted price for a new lid is over $200, and Maytag (I mean Whirlpool) tells us that it lasted through the 365 day warranty, so the bill is on us. It may be green when it works, but taking 18 month appliances to the landfill is not very green. And others on the web report say that the lid only lasts a year or so. The ratings scale needs to have negative values. Id give this appliance a -5.

I purchased this washer two months ago and have been greatly disappointed with it. I put in a large load on wash cycle, but the rinse cycle is barely any water, and is all soapy water, so then I have to turn it back to wash cycle to get more water and then back to rinse to finish it properly. I was never told about the short water cycle, why not? It is still under warranty, but said I have to deal with Whirlpool, and all they can do is send a repairman out and if it is not a defect, it will cost me $130.00 for the service.

We purchased a front loader Duet in August of 2011. It is now January 2013 and we had to have a service person come out. We did not buy the extended warranty because a washer should last longer than 1 year 5 months, but not ours! We need to have the drum replaced at $600. Are you kidding me! I will never buy another Whirlpool product.

This washing machine has been nothing but a problem from the beginning. Theres always something wrong with it. Things that cost so much should last much longer than a couple of years! I have to clean out the drain about every 3rd time I use it or it wont spin out as well.

Bought a new Cabrio, worked ok but in less than 2 yrs the bearing is bad. It will cost almost as much to repair as a new washer. Will never buy a Whirlpool product again. Would give negative rate!

Whirlpool cabrio mod. WTW7300XW1 - I purchased this washer Nov. 2013. It did not work right from the day of delivery. Our clothes come out dirtier than before washing. Machine smells awful. I spend more in machine cleaner than in laundry soap. I have always purchased Whirlpool. Very dissatisfied with this model.

We purchased a new Whirlpool washer in March 2010. Yesterday, 2/19/12, the washer stopped working. We called a repairman who checked the machine and told us the motor needs to be replaced. We called Whirlpool today, 2/20/12, and were told by their customer service department that since we did not have an extended warranty. We told them that we believe the motor should last more than 2 years. Their response was that if the motor lasted more than a year that was all they cared about. The only thing they would do is replace the motor if we gave them $299.00. I think it is very clear that Whirlpool knows it makes inferior products as they fail to stand behind what they make. I will never buy another Whirlpool product and would advise anyone who is looking for a washer to buy something other than Whirlpool.

The machine is two years old. It cost over $1,000 to buy. From the beginning, we have had mold issues with the machine. The entire house fills with the smell of rotten eggs every time we use it. The machine is used daily so it doesnt sit for long periods. Despite all the complaints online about their machines, Whirlpool refused to acknowledge that there is a design problem with the machine. They refused to make any repairs or buy the machine back and their only suggestion was to buy more chemicals from them to use to clean the machine. We have done this in the past to no avail. Oh, they did offer to send out a service company but on my dime. Whirlpool needs to be sued and I only wish that someone would start a class action suit against them. It really stinks when you try and do the right thing and buy American only to have the company not give a crap about their customers or the fact that their product is garbage. About 10 years ago, I had a Maytag front loader washing machine with the same problem. Maytag bought the machine back on a pro-rated basis, no problem, no question. Of course, Maytag is now owned by Whirlpool. Too bad they didnt adopt Maytags customer service policy. I cant wait for them to go out of business - something they deserve.

We bought this washer from Sears with big hope. Within the first year, we had 14 service call covered by the warranty but required 2 to 3 weeks in doing without. Whirlpool replaced the washer at no charge but continued to have various issues over the years. The new one is the control module that Whirlpool knew was faulty but did not let their customers know. The control module went over the weekend but I repaired it myself and do not have any more issues. I literally went in and tightened all of the hardware, removed and install the pulleys, motors pumps and replaced a lot of keep components with better quality. Guess that year the CEO made only 20 million rather than 19 million. Being an American company I was disappointed by the consumer relations people but everything is a throw away nowadays. Will not buy a Maytag or Whirlpool product again. Where has American product pride gone?

Buyer beware! I purchased a Whirlpool Cabrico topload and with my second wash, I realized I had a mess of a new washer. Ive called the call center on 3 separate occasions and I have spoken to other customers who have the sample complaint. The clothes are not washed clean. They have a residue left on them. My advice to all potential buyers, dont even consider buying a Whirlpool Cabrio washer. It is the worst purchase I ever made in an appliance. Im very unhappy with my washer.

I made the mistake of buying a whirlpool product and was wondering if there is a support group for angry unsatisfied customers? I have owned a duet washer and after 2.5 years is giving F1E2 error and is junk.

I bought it 1 week 1/2 ago and cannot wash correctly the clothes in it, have to rewash 2 or 3 times and bedding? Forget it. Still is dirty. Water does not go over the clothes, it suck for the price I paid.

I have a Whirlpool cabrio washer (Model: wtw6300 Serial Number: CT3573525) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. At the beginning, I didnt care because I had warranty with BrandsMart. I had to call at least four times. But now, I bought the automatic control and it didnt work. For two days, I was trying to balance this machine but it is impossible since the beginning.I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool. Two of the gas burners of my Whirlpool kitchen, after two years of use, are no longer working. I will definitely contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!

I bought my Whirlpool top loading washing machine 07-22-14. I so dislike the locking mechanism and will be certain to never, ever buy a machine with that feature again. It is so irritating to try to add something but cant because its locked so have to hold the button 3 seconds to unlock and start all over. If there was any way to get around it I would. I will stay away from Whirlpool products in the future and will be sure to check the next time I buy that the lid of the washer can be lifted when not spinning. Also, I do not like that it sticks on rinse sometimes and the only way to end a cycle is to hold the button and then start over with much wasted water.

The washer does clean simple stains. The clothes end up all twisted (sleeves & pant legs). Antiperspirant gets transferred to dark clothing. Large loads do not get clean and the response from Whirlpool was run everything on hot and for longer than normal times. The enviro rating and low water usage claim has resulted in a machine that does NOT fully clean clothes. Look elsewhere and do not buy.

This is the worst washing machine I have ever owned. I have had the Whirlpool Cabrio for less than three years, (4 people I use it for), and it is so loud when it is in the spin cycle, you think a jet airplane is taking off inside your house! Apparently the bearings go out of these machines when you use them! I called the company and all they want to do is sell me an extended warranty for over $300.00 for another year! Not doing that! I paid over $1,000.00 for this machine. I thought it would last a long time! Wrong! Please save your money and get a simple old fashioned one! I sure wish I had! Whirlpool doesnt care about their customers, or they would stand behind their products!

This Whirlpool top load washer has been an awesome product. I have had it for 9 years and havent had a bit of trouble. Its very quiet and very reliable. The only maintenance is running a cleaning tablet on the cleaning setting once per month, and it tells you when its due... No musty smell problems that I hear from people with front loaders. Its a great product.

I cant believe the list of people here with poor quality of their washing Machine. My first problem was covered under warranty. I have paid for two service visits from A&E and now every 5 minutes get the LF error. My fabric softener does not drain into load either. My only option is repair again and I got a sorry from Whirlpool. I think Im going to look for an old fashion cheap machine as it cant be of worse quality than this Cabrio wtw6400sw1.

This washing machine was already in the house when we purchased the house two years ago. In those two years, it has performed well for the most part. It has many different cleaning options, the clothes come out clean, it saves on the amount of water it uses, it’s quiet and I like the fact that it is a front loading washer.

Whirlpool Cabrio Washer WTW7800XW2 - After buying my American made washer..... at nearly $900 with extended warranty about 2 years ago. This week noticed small cracks in plastic that surrounds and holds glass lid. Now lid will not sit flat and glass is emerging from encasement. Called extended warranty claim center and was told it was a cosmetic issue. Called Whirlpool, and was told they were unaware of this flaw, even though countless websites, chat sites, and Youtube. My frustration is how they claim to be unaware of this flaw and refusal address it, after countless consumers have called. I would be willing to start a class action on this matter!

Bought a Whirlpool Cabrio Washer, which I see has MANY complaints. I had a problem with the F1 issue during the first year. Same issue and I was also told Whirlpool knows it was bad design yet they refuse to help the consumer in anyway. Maybe 50% a new WP washer. Upon my call they will fix it for 389.00 and give a 1 year warranty again. Im no longer confident in WP products.

I feel as though they could use some additional features, it’s also hard to change out some of the wiring in the back. I’ve had some issues with smells coming from the washers as well from them. Hopefully they can start to look into tweaking smaller details to improve the overall machine.

I bought a Whirlpool Cabrio washer on 11/07/10. I brought it home, hooked it up, turned it on and water came pouring out the bottom. I should have known better then, but I took it back and got another one, same model. I dont even have it 2 years and its locked up. I had a repairman here and was told it needed a new water pump ($200 plus). There are 3 adults in my home so its not like I use it hard. I am really disgusted. This is the 3rd washer I bought from Whirlpool in less than 10 years. I went on the Whirlpool site and voiced my disappointment and my problems with their washers. I was told they take pride in their products and I should have a nice day. Yeah, right, they dont have to drag clothes up and down the stairs and then to a laundromat when theyre in their 50s with a bad knee and back. Yes, I will have a nice day when I get that piece of junk out of my house. I will never buy anything made by Whirlpool again.

My new washer quit working properly. It does not spin or wash properly.

My agitator-free washer began tearing small holes in my clothing and sheets about one year after purchase. I contacted Whirlpool and they sent out a service person, who ran a diagnostic test on the washer and said it was fine and I should learn how to wash clothes and load the washer, etc. The barrel of this washer has little holes and I believe that when it spins the clothing, some pieces may stick in one of those holes causing tearing. The service person also told me that my clothes were old. I guess that means this washer is not for washing old clothing. The tears in my clothing are in places that are very unlikely to tear, like the back of my jeans behind the calf of a leg, about half way up from the ankle. There are holes in my tee shirts at the bottom of the back. Even if I were a smoker, which I am not, I would not likely burn holes in those areas. Whirlpool obviously does not want to accept responsibility for this problem, even though there are many other people having the same problem with this type of washer.

My Whirlpool Cabrio has been a real workhorse of a machine. It has been able to take large loads and small loads and get them equally clean and fresh. This was a more expensive model but it was worth the purchase price as I have used the various features provided. I also have appreciated that if you leave clothes on the washer overnight they are still fresh in the morning.

Its a front loader and has lots of cycles and temperature to choose from. Its setting on a pedestal so its not too low. I dont like the way the soap is dispensed.. If you still have the door open when you pour it in the dispenser it almost comes out on you. It also knots your clothes up and makes them hard to get out. The rest is good.

Whirlpool Cabrio washer - I had all the same problems as all the 900 others on this site. After 7 months, it died. The factory repairman told me it needed a new transmission and motor. I returned it to Costco for a full refund and did a lot of research and bought a Speed Queen. It has no computer. It’s just an old-school washer that cleans, and best of all, it’s made in the USA with a 10-year warranty.

The tub mounts of my 6 years old Whirlpool washer are broken. It’s too expensive to replace. Seems like built in obsolescence! Ive also had mold/odor issues. Finally, I know how to fix that, now this. I just want to warn others, these machines are not designed for the long haul.

Whirlpool Duet 3.9 cu ft High-Efficiency WFW9451XW00 - Hear my first experience with Whirlpool. I purchased a washer machine 30 April 2014. Guess what - machine stop working suddenly on July 30th, just about three months later. I had a lot of guest from overseas. While they visit me, I did not have my washer machine. How embarrassing. It was big mistake to buy Whirlpool. It is all made plastic inside and they uses cheap Chinese material. Anyway, technician came house to check what the problem was... all control system was burned. He ordered almost 10 parts from Whirlpool on 04 August. Whirlpool scheduled delivery for 20 of August. I called them for them to send the parts faster so my guests could wash their clothes. They send them little faster for August 16. After a day, technician was in the house again. I waited about 3 hours for him to fix my machine. He was really nice guy. He put install all new parts. Just in front of me, new parts broke after 5 minute. Whirlpool still did not contact me about their decision. Today is August 26th... I called them 5 time already - Nobody give me useful info. NO Whirlpool, guys - bad service.

Whirlpool Cabrio Washer-Dryer - Bought a set a few years ago at Lowes. They are a very attractive set and I was pleased at first. Now, I have had to have repairmen out for these units 3 times. The bearings keep going out on the washer because it spins so fast, it wears them out. Now the thing is leaking. Whatever happened to the days when appliances lasted 15-20 years. For the high cost of these things, they are junk. I am very disappointed. I will never buy one of these again.

I join the many who have posted about the Whirlpool Cabrio Washer cracked lid issue. Our Whirlpool Cabrio WTW7800XW2 glass-lid washer suffered the same (inevitable) fate – cracked plastic on the lid at the hinge stress points, after the washer was beyond warranty. Same story - runaround/no help from Whirlpool. Finally bit the bullet and shelled out the $200 for a new lid. HOWEVER, I didnt want to just replace it and have the same issue down the road. I removed the spring-loaded units that support the hinges, hoping to just remove the springs to release the pressure. I found that the springs are integral to holding all the components together in this unit. These are extremely heavy-duty extension springs, so I took them to my hardware store (TrueValue) and found springs the exact same length, but with a smaller wire diameter and thus requiring less force to extend. I replaced the original springs with these (Century Spring Corp. - #C-143 - 9/16”x3”x.054”). The lid operates perfectly, and now there is very little resistance at the hinge stress point. The only difference is there is no longer a “damping” effect when lowering the lid - it must be lowered manually rather than being allowed to fall on its own. That’s a small correction in habit, but will ensure that the replacement lid lasts for the life of the washer.

I have a Whirlpool Cabrio washer. It was great for almost year. After that it has been nothing but trouble. The body of the washer has rust coming through the paint and large areas that is so rusted that the paint has chipped off completely. A washer is expected to deal with water and not rust through the body. I have a 10-year old Ford truck without a speck of rust. Dont they undercoat? The circuit board has had to be replaced because of rust. I have to take several Q-tips and go under the cover to remove all the rust if I dont it gets rust stains on my clothes, which is impossible to remove. The customer service is non existent. They have left me on the line for over 40 minutes. I hang on only because it would be another hour or so of my time to get someone to answer. I was without a washer for a month while waiting for parts. Why dont they have parts for their products? I had to slop my way too dirty laundry mats 3 times a week as I do 2 to 3 loads a day.My washer is downstairs and stops and gives me the unbalanced message even when its not, running up and down the stairs several times to complete one load. I also get the F51 message for no perceivable reason. The extra rinse button only works 1/2 the time. This was an expensive washer ($1,000.00) and I feel that I deserve my money back. They are knowingly making an inferior product.

Whirlpool Duet Sports washer purchased 11-08 was found defective by service technician due to improperly secured bolts on counterweight at factory. I contacted Whirlpool service and was informed that warranty will not cover any parts or labor. I ordered parts for repair. It will take at least 2 weeks until arrival and repair of item. Clothes washing now were taken to town for washing at additional expense. After repair, only 90 days of warranty was given by the service technician. The cost of $260 to repair item for a possible life cycle of only 90 more days seems ridiculous.

Ive had my Whirlpool Gold for over a decade and absolutely love the quality and performance of the unit. No maintenance issues whatsoever throughout the years. I recommend this washer to everyone I know and continue to enjoy the performance and reliability of Whirlpool. I will continue to buy this brand every time as needed.

I purchased a Whirlpool front loader as well as an extended warranty. The machine worked well for about a year and a half until i noticed rust patches beginning to form on the front of the machine. We contacted the retailer that we purchased it from and they suggested that we call the people that we had bought the warranty from. Unfortunately, the warranty does not cover rust, so we have to wait for it to rust out and just buy another one. It is only 2 and a half years old and is totally rusted across the front of the machine! It is extremely unsightly. This is the second Whirlpool washer that we have bought and the second one to rust out on us. I would never buy another Whirlpool appliance, and extended warranties are not worth the paper they are written on, let alone the amount that you pay for them!

I love my Whirlpool 4.7 cu. ft. top load washer because it has a pretreat station that is super handy for pretreating stains in a handy little place. The agitator is stronger than my old washer and really gets my clothes cleaner. Its also very quiet and easy to use all the buttons. The best feature is the deep water fill that you can select for more water.

My new energy-saving Whirlpool washer sucks. Laundry comes out smelling as bad as it went in. Washcloths are as dirty as they were when they went in. I have to take my dogs bed blankets to my sons home to wash them because this new washer will not even clean blankets.UPDATED ON 08/21/2015 - I have had two Whirlpool washers in 38 years. They were great. I buy a new up to date energy-saving Whirlpool washer and it doesnt last a year and a half. Now it is costing me $433 to have it repaired. I am preparing a washer and I am very unhappy with to start with. I will never recommend these washers.

I have the top load Whirlpool. Its very roomy for my covers, rugs & towels. It has a setting for me to just clean my washer or if I need to just rinse it. It has a cycle just for that. Or if I need a quick wash or a just cold water wash it has those cycle. When my cycles are done it makes a cute jingle sound to let me know its done.

whirlpool Cabrio Washer - I replaced my front loading Duet with this, thinking I was done with front loader. Designs are set to fail, liked the idea of no agitator, thinking can clean a lot clothes at once, boy was I wrong, heavy loads wont spin dry, forget sheets or blankets. The machine just stops, leaving everything soaked and you basically screwed, you can invoke a spin cycle but to help make rinse and spin out, sooo disappointed. Whats wrong with the designers of this product? They didnt try sheets to see if it would even work. I am far from over loading this too. Dont buy this.

I have had the same lid problem with our washer. New in 2010. The lid just broke in the same place for the 3rd time! Called Whirlpool customer service. Yes they can find my account. No, they dont have a record of this happening to this washer before. Even though I called them and got the lids through them two other times!!! But they will be happy to send me a new lid for $260!!! Also love the fact that they dont acknowledge the lid is a problem. Time to find a new washer that isnt Whirlpool!!