Our Whirlpool Dishwasher model WDT710PAYW is less than 2 years old and is rusting on the outside of the door where the steam vent is. Apparently the hole that was made in the door for the vent was not sealed, now the paint is blistering up due to the rust. Will not purchase another Whirlpool.

I purchased a Whirlpool Cabrio Set from a local store. Just over a year later, the washer got very loud like a jet engine. Called the registered repairman, he came out took a look and said he would get back to me. Called him 3 times over 3 weeks, no show (Hoodland Appliance). Called someone else, repaired it for $400.00. Called Whirlpool, they are not interested. 2 years later now and the machine is getting loud again. This is due to the spin throws water up and it is able to get out of the tub and down into the barring and the soap residue wears the barring out. Bad design. Called Whirlpool again and again they are not interested but can put me in touch with a repairman. I will not repair again but will use until dies and buy something else not related to Whirlpool. So much for energy efficiency.

I dont know who is the bigger idiot. The designer of this washer or me for not reading the countless bad reviews. I bought a Whirlpool 4.3 CU FT TL WTW5000DW machine on 7/19/2015. It does not come close to cleaning clothes. It now takes me three times longer to do laundry because I have to check every piece of clothing for any stains. These are minor stains mind you but, they will not come out unless I use something like Spray and Wash. My time is valuable, maybe I should drag my clothes to the river and beat them on a rock. Very disappointed.

Last year, our clothes started coming out too wrinkled. And until recently, its making a loud noise like an airplane. I called Whirlpool, and the only help they can give me is finding a company that would do service and would charge a lot.

This is the worst washing machine Ive ever purchased. Bought 12/19. The water level never never goes up high enough, to cover the cloths. I have to add water no matter what setting. I hate that. The sensor isnt working. You arent able to adjust it yourself, its computerized. The water shuts off when you lift the lid so you cant rinse out the soap or fabric softener caps. I hate that. The lid locks when the rinse cycle starts so I have to unlock the lid to add fabric softener. Why lock the lid so soon, wait till its in spinning mode. Really really badly designed!!!! Will never buy anything by Whirlpool ever again!

Purchased Feb 2013 - worked okay until one month ago. Now stalls in the drain and spin cycle. The rotation of the drum sounds awful, makes a loud grinding noise. I tried doing the diagnostic reset of holding the Temp button in for 3 sec, release, 3 sec more but that didnt work. Also, I have noticed clothes are DRY after the Wash cycle! Managed to interrupt the wash and unlock the lid and was very disappointed. This is not a good quality piece of equipment. This seems to be a very common problem. How unfortunate.

We bought our Whirlpool Cabrio Platinum top-loading high efficiency machine Model #WTW8000BWG in Feb. 2015. It cleans well, and is easy to select water temp, spin speed, etc. It's simple to load, but because I am short, I have difficulty reaching stuff at the bottom of the tub. A stool is needed. LOL. In the 5 years that I have owned it, I have not needed any kind of service to be done on it. Very reliable. I have had Whirlpool washers and dryers before and my success with them is why I purchased the set I have now. And so far, so good. Highly recommend.

We get the error code F1 in the start of the cycle and when there is 21 minutes left, we have to stop and reset at least 7 times before the water fills. We put a new sensor in for over $200. The second problem is it goes off balance no matter what the load is. I was going to have it fixed (if possible). After reading all the above I wont waste any more money on it and go buy an old fashioned reliable washer. What a piece of money sucking machine especially when I dont have any extra money to waste down the drain. I wish I knew before. There are a lot of people this time of year I would have rather given the money for a needy cause. How disappointed we are with Whirlpool!

We purchased the Cabrio Whirlpool washer from ABC Warehouse October 18, 2014. They said if we purchased a washer of higher quality it would last longer. We have bought Whirlpool washers for over 40 years. When our last one only lasted for three years they convinced us to spend more money over 1000.00 witha purchase of a 5 year warranty 6 days over the warranty. It is junk. The bearing went out costing 600.00. They graciously offered to sell me another washer. WOW, everyone is sorry that we have this problem BUT you are out of luck. Are they kidding? I will never buy another Whirlpool. They use to be the top of the line but now I feel we are in a throw away world and talk about consumer rip off. FLEECING OF AMERICA AT WORK!!!!

The washer has rust under the rim in the inside - also the paint is bubbling and peeling under the rim of the washer. I contacted Whirlpool and was told that is a cosmetic problem. There is no warranty for rust or peeling paint. I will never buy another Whirlpool washer. I paid over $700.00 for this washer and I dont think I should have a rust problem after 5 years.

Completely disgusted and angry with Whirlpool! We own a Cabrio and just after 1.5 years of owning it the stupid washer has broke down. It wont spin or rinse or wash! Pretty sure its the bearings as I have seen several peoples complaint about this same issue! I contacted Whirlpool to only be told that they only offer 1-year warranty and after that the consumer is out of luck. They only stand behind their products for 1 year and after that its on you! They refused to help me in any way including sending someone out to look at it! Im very upset and will never buy another product of theirs! They need a class action lawsuit brought against them!

I purchased a Whirlpool Washing Machine in November, 2015 and today, I had a repair person out who said the bearing had ruptured and the washing machine cannot be repaired - 2 1/2 years later. Contacted Whirlpool Customer Service who would do nothing other than try to explain to me that I should have purchased an extended warranty as they could not stand behind the machine past the one year. Would not even offer sending a tech out on their dime to confirm what my repairman had said that this is a failed production process of these machines - it was nothing that I had done caused this issue. But yet they wanted to sell me another machine. It will be a cold day before I purchase another Whirlpool product.I was shocked at the lack of customer service to assist with a situation that both the location I purchased it from and my own repair tech said that they are seeing so often with these machines. I would never purchase another item from Whirlpool again nor would I recommend any of their items. I will go to great lengths to give others the background on how Whirlpool will not stand behind their products, lack of customer service to resolve a situation or can work outside of what is given to them to correct a situation - this is not OK!

I purchased this monster in 2012 and after six years of enduring not enough water to actually wash the clothes for years, now the bearings have gone out making it sound like a jet engine is in my family room when it spins. After researching the bearing issue, I find it will cost $250 to $300 to have them replaced. Its also a common problem in this model even when the washer isnt at all worn out and old. That combined with the fact that my clothes dont smell clean and some blankets come out not even wet at all, Im done. I wont ever buy a water efficient washer again. Churning the dirty underwear around with a few cups of water isnt acceptable. NOTE: The bearings left months after the extended warranty expired. Just like clockwork. I purchased a much cheaper - center agitator - washer with a deep water option available. It was half the price of this top of the line Whirlpool Cabrio Washer.

I purchased the Whirlpool Cabrio Washer WT5500XW2 from Lowes on 9/12/2012, which turned out to be the worst purchase of my life. It did ok for over a year. It had always been noisy. Now it sounds like a jet airplane when it is on the spin cycle. This machine is not yet 2 years old. Do not buy a whirlpool washer. They are Junk. Plan on getting rid of this piece of junk and buying a new washer. Dont waste your money on Whirlpool!

This machine is junk. It does not get clothes clean. I had jeans that I soaked and were fairly clean when I put them into wash and had another pair of jeans with a little dried mud. My whole load came out filthy. I am having to rewash the whole load after hand cleaning the washing machine. I replaced a machine that was 25 years old that did a better job than this piece of junk now sitting on its place.

I purchased Whirlpool Cabrio on 04/06/2017 at Best Buy in Lake Worth. The washer stopped working last month. I went to Best Buy to complain. I was told to contact Whirlpool which l did. Was on the phone for over 2 hours with representatives. Finally l was told a service person will come take a look and tell me whats wrong with it. The service person came after one week out. Told me he has to order parts and it will take a week for the parts to come in. That his company may send some else to come and fit the washer. Meanwhile l took off the day from work.Now today 08/08/2017 the service company that Whirlpool contract with sent another service person with the parts only for him not to be able to repair the washer. He has to order more parts and it will take another week or so. I was so upset called Whirlpool, spoke with two different representatives. All they could say is sorry for the inconvenience that l have to wait until the service person comes out again with the parts. And if he cant fit thats when they will be able tell me if it will be replace. Bottom line is that l will never ever buy Whirlpool products again.

Whirlpool Cabrio - This expensive machine should be called the Presidential. First it spins, spins, spins. It sprays tiny amounts of water, so little, that there is 2 inches or less. There isnt enough water to cover the clothes so no agitator to stir and mix them. There are ridges on the bottom of the tub called aggrivators to twist everything into pretzels. This twisting spreads the dirt around, but does NOT remove it, the utter lack of water giving it no where to go. I use a hose to add extra water, and I hand soap dirty spots. I stop the washer frequently to hand rub and slop the clothes around and un-twist them. Explain to me how running this machine 3 times plus adding water saves water and energy. I cant, in good conscience, sell this POS to someone else, and I cant afford something else. I sure miss my simple reliable old Maytag. I could say even more about this atrocity, but not now. I HATE THIS POS!

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

I purchased this machine three years ago. It is junk. I have had two washing machines and they lasted for years and years. Never had a problem with either machine. I purchased them from Sears. When I the Cabrio, I was told it was the top of the line washer for Whirlpool. Three weeks ago it started making a noise like a plane taking off. It wouldnt spin the clothes. The repair person said that it could be three different things the parts, for which, would cost in the vicinity of $200. However, since it was making such a loud noise and water was coming out from underneath the washer, he was certain the transmission was out. He said the noise was an indicator the bearings were gone. I didnt see much point in repairing the washer if the transmission was out because it couldnt be fix.There was a couple at Lowes purchasing a machine at the same time as myself. They said they had a Cabrio also and it was only two years old. It wasnt spinning the clothes either and making a tremendously loud noise. They told us this before we mentioned that we had a Cabrio also. I will neither purchase another Whirlpool product. Junk!

Have used washer since 2005. Still runs today. Minor repairs done. Is reliable brand. Whirlpool gold model washer purchased at navy exchange. Will buy another whirlpool again. Have bought other brands which lasted 7yrs and then needed replacing. This whirlpool is the best. Lasted 15 yrs and still working fine doing 5 loads a week.

I had my washing machine for about 10 days before it stopped working. I did about 4 loads of laundry. We have had 3 repair people come check it out, all referred by Whirlpool. They each had a different theory on why it wasnt working properly. Im now waiting for parts to be delivered and then service to be scheduled. When I contacted customer service, I was told (after waiting on hold for about 1 hour) that it was customer misuse. Ahem, first I heard that, and I think I know how to use a washing machine. I asked to speak with a supervisor. More waiting. Tina (#**) told me she will contact the service company about the parts. I told her to please conference me in on the call because I want to hear the outcome (and I dont want to wait another 1+ hour to reach customer service again). She put me on hold and then disconnected me! Really, all this time and 3 service people... Would be cheaper to just replace the machine altogether. What a headache!

The washer in this set is my biggest complaint. I have followed all instructions and tried different methods time and time again and the clothes never come out fully clean. I too experience all the other complaints on this site as well, stuff still left on clothes, dry spots, stains not removed after being pretreated etc. I did some research before buying this set and saw some good reviews, dont know who wrote them but obviously they were highly inaccurate. This is my biggest purchase regret ever, as this set cost about $2500, so disappointed.

I have had the machine pair (Whirlpool Cabrio Platinum) for almost 4 years and up until a few months ago I LOVED the washer. I was advised when I bought the machine to make sure to read the manual, which was very helpful in learning to use it properly. I have never had residue on my dark clothing or ever had the clothes come out partially dry. I use liquid HE detergent nothing powder goes in the machine. I also read many reviews before buying it and a got some advice from them. I have washed king size comforters with no problems. Everything has always cleaned very well. The only issues I have are that when bleach was used in a previous cycle. Ive had a problem with the bleach not being fully dispensed and ending up in the next load. Fortunately it was just towels and not darks!!! Although, I had just bought the towels and now they look tie died which was very upsetting to me. I learned to add water to the bleach dispenser to dilute it and that issue seemed to dissipate. BUT NOW... I COULD THROW A TANTRUM. I PAID 1800+ FOR THE PAIR AND THE WASHER IS SHOT!!! A pretty common problem with the Cabrio from what Ive read. It started by making a very loud noise when spinning, like a helicopter was landing in my laundry room! I continued using it, I even thought the sound was getting better after I did the clean cycle. The last load I did would not complete the cycle because it kept reading that it was unbalanced and unfortunately it was a load of heavy wet towels. I was far from happy when I had to remove them and go to a Laundromat. Needless to say its the bearings and to fix its very costly. I cant even fathom that a less than 4 year old machine needs to be repaired and the cost is roughly half of what I paid for it!!! I do know I will NEVER buy another Whirlpool. What happened to making things to last??? Next machine I will definitely get extended warranty. I can honestly agree with all the other reviews... THIS MACHINE IS HORRIBLE!!!

I purchased a new Cabrio Washing Machine and Dryer in March 2015. I have had 3 new washing machines thanks to the Customer Service provided by Lowes in Lindale Texas. The third washing machine has again lost its brain and the sensor to operate the machine. I have been waiting for the parts since December 2. Called it is still on back order. Unacceptable! It cost almost $60 dollars every 2 weeks for our washing at the Laundromat. Again unacceptable. All Whirlpool can say is We are sorry. When the machine works my clothes are beautifully cleaned using the new HE soap. Takes large loads and I love that part.I am sorry I bought a Whirlpool. Whirlpool would not work with me except to apologize and say the parts are on back order and I will get a call in 5 days for an update. These machines cost $900 each plus tax. They should work more than 3 months at a time. The first repairman could not explain anything. Said they were too new and he could not figure out what to do. The second repairman was more knowledgeable and explained what was wrong. Does not help that Whirlpool does not have an inventory of parts to take care of their customers.

Purchase 2009 Duet Washer & Dryer (WFW9700VW00). Recently have had error codes coming up - F35 for one. Could not get washer to reset. Had to keep unplugging and plugging back in. Service was called and the tech knew right away what was wrong. He ordered and installed an analog pressure switch. While he was working he mentioned that this was a known error and if we had called with this problem a couple years ago Whirlpool would have replaced the washer. Im not looking for a replacement but I feel Whirlpool should cover the part having been a known issue.

We purchased 2 whirlpool commercial coin operated washer machines and both computer boards had to be replaced twice each - model CAE2743bqo and CAE27438qd.

2 years of use the wash plate went. $150 later, one year later wash plate went again (the wash plate is all plastic, the motor spline in metal total stripes the plastic teeth in the wash plate) I replace myself. 3 weeks later the shift actuator failed which cost another $60 which I replaced. Now the bearing is going. There are only 3 people living in the house. I would stay away from the top loader washers from Whirlpool h2 low series. Huge disappointment.

I absolutely hate this washing machine. When I bought it a couple of years ago I thought it would be great for large items... NOT! It leaves white residue on dark colors but the MOST important issue is going off balance. The lid stays locked and you have to start the cycle from the beginning... What a waste!!! Never again will I get a Whirlpool.

My washer worked less than a year. I finally called Whirlpool and they basically said, were a big company and you must for the rusty, broken drive shaft, pay for all new computer face plate, and service repair. I contacted the FTC and they told me they needed more complaints in order to make them do a recall on Cabrios. Good luck!

My Whirlpool Cabrio Washer is only 4 years old. I have had balancing & spin issues since day one. Thought it was just me. Constantly had to drain and spin after rebalancing. Now 10 days ago it cost me $250 to have it fixed. The aqcuator (?) Went. It wouldnt spin out. Now 10 days later it stops again. The appliance guy reads code. F7E7. He tells me the bearings are no good. Will cost another $400 and they need some special tool to fix it. IM DONE. My last set was 15 years old. The price is ridiculous and quality not worth what this triple capacity set cost.

Back in the day GE appliances were made to last and last - the only one I have found close is Whirlpool. They have style, dependability and long lasting products. My washer machine has a ton of features and I didnt pay more for any of them.

I purchased a Whirlpool Cabrio top loading machine approx 3 yrs. ago. When I first bought it, the machine was super quiet... loved it. I loved the capacity of it. About a yr ago I noticed it started making all kinds of noise, we cant have a conversation downstairs because its so loud. Turns out the bearings are broken. The technician was nice enough to explain to me that its a common problem with those machines. However, Whirlpool is not willing to stand by their product and repair it free of charge. Any other product would of been recalled and repaired. That goes for cars, baby products, and so on. But not Whirlpool, I called and spoke to Andrea in Michigan who told me that there is nothing that they are willing to do. After reading the other reviews and their terrible one star average rating it doesnt surprise me. Shame on me for not researching this product before buying. I hope this saves someone else from making the same mistake. In case your wondering, it cost me $117.00 to have the tech look at the machine. The labor would of cost $125.00 and the part is $251.00........

I purchased the Whirlpool Duet Steam Washer and Dryer in the spring of 2010. Washer bearings just broke. I was told that the bearings in these machines are not strong enough to support the spin cycles. It is very disappointing to think that a company like Whirlpool would have their customers pay $1000 for a machine they know is not going to last. I agree with Julie. Maybe a class action lawsuit needs to be filed. Is there a lemon law for washing machines?

I purchased this washer from Lowes 5 months ago. I did not purchase a store warranty. Started having problems 60 days later. I have to deal with a Whirlpool rep. The company is 150 miles away. They have been to my home 3 times to resolve the issue. They replaced an air trap. The problem... my clothes still wont spin dry!!!

The washer worked well the first year and has gone downhill since. There is mold on the rubber seal where the door closes. This was supposed to be a recall and was never sent the replacement part. We have to constantly use bleach to clean the rubber.

Whirlpool Cabrio Platinum WTW8800 model - In the words of the service technician who came out finally to service the machine. This machine is a piece of crap that should be recalled from the market. It is a low level-water unit that has no agitator ability in it and does not provide enough water to even slightly clean clothes. Everything must be sorted into the smallest loads possible and even then the clothes dont clean because they beehive into a ball and do not agitate. Technician says the machine cannot be fixed and simply recommends it be trashed (it is 1 1/2 years old). Technician recommends going back to front loaders where at least the clothes agitate. Called Whirlpool for help and was told all system are down...duhhhh. Call back in an hour and Good Luck.

We purchased a Whirlpool Cabrio washing machine on 3-18-16. In February of 2017 the washer died. I was bleaching my whites at the time so most of the clothes, whites fell apart because they sat in bleach and water for 2 days. I had to figure out how to get them out without getting bleach and water all over my clothes. I called whirlpool and they got someone to come fix it. The tech came and said we needed a new control panel. We waited 3 weeks for the panel. He came on 3-24-17. He put the part in. Took less than 10 min and said, All set. I went downstairs and put a few things in. I was a bit leery and the machine started. I went back upstairs and I hear beeping. I go back down and the machine is flashing again. I called the repair people they said, Unplug it for 10 min. It may reset itself. If it doesnt, call back. It didnt. I called back and wanted me to wait till the following week. I told her I had clothes in there.Someone came the next morning and said it needed a harness and they would order it. Well its the 28th and I havent heard anything. I have called whirlpool several times with no satisfaction. We had the machine less than a year and its been dead for 2 months. I am disabled. I have multiple sclerosis so every day is a new issue. I hate to put that in here but I want you to know what Im dealing with along with a dead washer. Any help you can offer would be appreciated.

We purchased Whirlpool Cabrio 8.8 cubic ft Electric Dryer with Steam Cycles (Chrome Shadow) Energy Star Model WED8500DC and Whirlpool Cabrio 5.3 cubic ft High-Efficiency Top-Load Washer with Steam Cycle Model WTW8500DC and have had no issues at all, only personal issues, such as me being 54 tall and cant reach the bottom of the washer tub to take out all my clothes, so my husband helps, he is 5 9 tall and can reach in it fine, so we do laundry together now! We have washed very small loads to large loads such as, bedding sets without any issues at all. We love the gorgeous look as well. We have only owned these since November 2015... so about 4 months now, but we are completely satisfied! We have always owned Whirlpool, our old set we bought in 1998 and they finally gave out in 2015! Whirlpool for life for us!

Whirlpool Duet Front Loading Washer. Purchased date was 1/09/10 and I paid $629.00. It failed in 7/1/11 and got a service call for $60.00. The result of service call: Bearing shot and crank shaft broke. Im very disappointed. Whirlpool should be liable for the malfunction of their product. Whirlpool was contacted and they were sorry that there is nothing they can do.

A total loss of money. Does not use enough water to clean clothes. Gets out of balance all the time. Do not buy.

We purchased a Whirlpool Cabrio model # WTW6400SW3 in 04/08. Approx. 6 months ago, the washer started to be un-level during the spin cycle. This has progressively become worse, it now becomes un-level during the rinse cycle. We spoke with the appliance store where we purchased it, ;hey said the repairs could cost $400 or more. Thats nearly half of what it cost new. Like other complaints Ive read, cheaper washers have lasted years longer than the Whirlpool. Our last washer, a Kenmore, lasted 15 years.

Model CAE2745FQ0, Serial #C72680766 - Purchased this coin op clothes washer 2/2/2018 at Brandsmart, Deerfield Beach FL. Would not empty or spin correctly; 1st service call 2/28/2018. (Less than 30 days from purchase date). 3/21/2018 called Whirlpool again as same problem continues (as listed above). Washer is not being overloaded. Whirlpool repair visit scheduled again for 3/23/2018. This is the 2nd repair time since we purchased the washer on 2/28/2018. Purchased the same model 2 years ago, and experienced repeated problems to the point where we got rid of that machine and purchased the most current model referenced here. We are looking for a full refund of the purchase price as it appears that this recently purchased machine is on its way to be a repeat performance of the 1st machine that we got rid of (that was purchased 2 years ago). Again, we want the full purchase price refunded, which is $900.88. This machine is not even 2 months old. Thank you.

This washer is a piece of junk!! It doesnt use enough water to clean the clothes and now it wont spin them dry. I have maybe two loads a week on a regular basis. I have always used HE detergent. Never overload. It is only three years old and I have been having to go to the laundromat because I cant afford a service call and especially if it is what they say which costs almost much as the washer. Be ahead to buy a used washer or a cheap one. It wasnt getting the clothes spun out dry enough - dripping wet. Then it flashed od and ul and sd and f51 and then it kidnapped my clothes - couldnt get the door to unlock with the pause or power until I unplugged and still had to wait several minutes. They refuse to help. Do not buy this machine!!! The customer service was not one bit of help. Instead she wanted to charge me $350.00+ dollars for some plan.

I thank the folks at Whirlpool for building a washer (Cabrio tub bearing failure) that lasted 22 days just shy of four years, better than the Whirlpool Duet that lasted 14 months, tub bearing failure also. Now I have high confidence that Whirlpool pre-engineers failure into every washer they build.

DOES NOT MEET CONSUMER NEEDS AS PROMISED. I wish I read the reviews. Very expensive machine I purchased specifically for the large drum for large loads. The machine cannot handle large loads (if you consider one blanket large load). I have to unplug the machine mid wash, as the load gets stuck on one side and moves my machine across the floor. The noise in the spin cycle with even small amount of laundry sounds like a helicopter is about to land. Then last night I noticed black oil splattered all over my floor. This is a $800.00 machine. Never ever met my exceptions as the machine promised to deliver. Theres very little water that enters the drum... Not even my towels come out clean. DO NOT BUY WHIRLPOOL... EVER EVER EVER.

We bought a Whirlpool Cabrio in April 2012 and in July 2012, it started giving problems. It wouldnt start. It started humming. We heard money-like jingling noises. It stopped spinning and rinsing clothes. I called for service. No luck with that. So in order to wash, I had to drag the washer to the back door (which ripped up my new floors) hang hose outside for it to finish the load. Well a few months later, that didnt work so the assistant where it was purchased told us to cut the pipe down in the wall. Now we have a big hole in the wall. My floors are ruined and we are out getting another washer. This one is not even a year old. That was a $750 loss.

I purchased this Whirlpool washing machine in July 2009. The repairman just gave us a $1400 estimate for repairs due to failure of bearings. This is an energy efficient, expensive appliance that we expected to last for years and we feel that 2 1/2 years of service is unacceptable. We did not purchase an extended warranty and Whirlpool said they would help with the cost of parts - not labor. We cannot afford to repair a lemon and so purchased an LG front-loading washing machine today. Hopefully we will have a better experience with LG as we will not be purchasing any more Whirlpool appliances ever.

They are good washers but they are overpriced. They have way too many functions for doing laundry. I know everyone wants their washer to do it all but the machines just can’t. There is no washing machine in the world that can sense a stain and pinpoint it and remove it.

Whirlpool Cabrio washing machine: The washer was purchased in March of 2012 and malfunctioned in December 2014. After phoning Whirlpool, the machine was scheduled for repair with a factory-authorized company. The first repair attempt was unsuccessful due to a lack of parts. It took 10 days for the parts to arrive, and another unsuccessful repair attempt was made. The verdict is that a new motor control board, costing $350 plus labor, is necessary. With the delay in service and cost of repairs, I may as well buy a new machine.

I got a Whirlpool washer front loader model number wfw9151yw. Every time I wash sheets, they go into a ball. I called Whirlpool. They sent out a service guy. He said do not wash sheets in a front loader. I called the store. They said call Whirlpool again. Then the second service guy moved the legs down about 1 in. The machine still not right. I feel Whirlpool should replace the machine or give me my money back.

We purchased our Whirlpool Cabrio platinum washer about 3 years ago. I am completely frustrated with it. When it is on spin cycle, it sounds like a freight train going through my house. During the rest of the washing... it squeaks. And right now this is the 5th attempt to wash the same load of laundry. Because it keeps getting unlevel and it will not continue after I move the clothes around to get it level. So I have to start all over. There is not a spin cycle option that is available by itself. Every time I have to choose the rinse/drain/spin option. Obviously it is not under warranty anymore! Only a one year warranty... really pathetic! And when we called they offered us a little discount to buy another one. No thank you!!! Wont ever buy Whirlpool again.

Cabrio washing machine WTW8600YW0 - Had this washer for 3 years. Its been repaired a few times, but this last time theyve replaced the bearings 3 times and it only lasts less than 1 week. This $1000 washer is now going on the trash. I tried to get help from WP, to no avail. There is a reason these are only warranted 1 year. One thing I liked about it: the fast spin speed gets clothes drier. Every other aspect is crap. Cleans very poorly. You cant make it use enough water. The tub looks huge because it doesnt have a conventional agitator. But if you put much in there you will end up rewashing in small loads because then it REALLY cleans poorly. I bought this because my trusted appliance store owner buddy said he owned one. When I asked him lately he doesnt talk much except admits that yes they have had a LOT of trouble with these machines. The life is very short on them. The wonderful fast spin speed destroys the light bearings quickly. And it gets worse the more its worked on. Its a disposable $1000 piece of trash. Im an engineer, and whoever designed this should have his degree revoked. The type of agitator it has and the extreme low water is very hard on your clothes. One zipper left loose will shred your clothes. I wanted to love the thing, but I have to hate it because it is unrepairable. If you could control the water and if it lasted at least 5 years without having to rebuild it several times at greater cost than it was purchased for, I might be less than rabidly angry at WP. They know they are junk but dont care. You have few choices as they now own most brands, and they know this. I have a Speed Queen on order. Just a plain old simple washer.

We bought a Whirpool Cabrio, model WTW62000W9, and it is junk! We bought higher-end thinking that it would last. It is less than two years old and averages three loads per week. The transmission is out. It needs to be loaded on the boat back to China.

I paid over $1,000.00 for a washer based upon previous experience with Whirlpool appliances. I am single, over 65, and use this machine infrequently, as compared to when I had children. The only thing Whirlpool is offering is another of their machines at a discounted price. I value principles more than dollars. I refuse to give them another $600+ as a reward for making junk which apparently should have been recalled. The part I need is not available any place Ive found online. And it completely controls the power to the machine. You cannot open the door, you cannot turn it on. I had two service calls to discover this part is not available.

Purchased washer 8/2015. Washer quit working 12/2015. Would not drain or do anything. Repairman dispatched and came 3 business days later. (They dont work weekends.) Repairman looked at old receptacle cover and immediately stated, Problem with polarity of plug. No prior problems with plug running appliances. Plugged into it for over 8 years. When I advised him of that then he started troubleshooting circuit board. He cleaned out the machine and got it to work. (Still under warranty) 4 days from repair, and machine quits. Same problem. Wont drain and wont do anything. Call for service again on Weds. morning and given following Tues for service call. Online consumer reports complaints #ered at over 1,7000. Same machine, same problems. Call Whirlpool directly, given runaround. Talk to Whirlpool mgr. (Robert) complaint # **. He states, Have to wait for service. But calls Brandt Melb., FL to try to get sooner service. Brandt calls me stating they have ordered a lid lock and CCU board for machine and will be out Monday. How would they know to order these parts if it is not a constant issue? Im thinking class action suit for shoddy product... LOWES Indian Harbour Beach, FL. Transaction #**.

Rust started forming early on our washer and spread quickly. Our house is air conditioned and not near the ocean. There was no reason for the rust. Poor quality finishing is the only explanation. When I called to complain I got nowhere. I wish I could show a photo on this website. It would dissuade anyone from ever buying a whirlpool.

When I purchased my Whirlpool Cabrio washer and dry, I was told by the sales associate that this was the top of the line. I paid a higher price for what I thought was quality only to find out that this washing machine (WTW6600SW2) Serial number CU2973872 is in fact poor quality, made of components that are cheap, unreliable and made to last only as long as the initial warranty. Prior to buying Whirlpool, I owned Kenmore and had a washer and dry that raised four kids, now I own a Top of the line Cabrio that cant wash the clothes of two adults. I think it is funny that two days after the washer started sounding like a jet plane taking off during the spin cycle, I received your sign up for an extended warranty letter. Then I take the washer apart to locate the trouble and find it is a single bearing on the top of the drive shaft, but can I buy the bearing and replace it? No, I have to buy the entire outer tub and drive shaft. So a $10.00 bearing will now cost me $200.00. I am sure that helps your profit margins considering all you have to do is a search for Cabrio problems to find 350,000 hits, or to ask a professional technician and receive the reply that they are replacing 2-3 of these tub and drive shafts per week. I would recommend that Whirlpool tell its shareholders that you have compromised customer satisfaction to line their pockets with profits. If that was your intent then you have succeeded, however you need to also tell them to sell their shares now as you will have no return customers. Most corporations have core values that deal with safety first and then always followed by quality. I can say with confidence that your quality can be nowhere near the top five with this many problems with your top of the line product.

I purchased a washer from Whirlpool through Home Depot on August 7, 2014 and on Dec 31st, 2014 the washer broke. I called Home Depot and was told to call Whirlpool since I was still under a year warranty. After numerous calls I was referred to Advantage |Appliances, a company that provides repair services for Whirlpool. After a week the technician showed up and briefly inspects the machine to conclude that there were two problems with the machine: The controller is defective and there might be another problem since the water is not draining. An order was placed for the part and another week went by with still no part. I called the corporate office only to hear that it might take 5 to 7 days to receive it. In the meantime I had laundry piling up. I was forced to go to the laundromat with one arm in a cast and a painful lower back. I finally received the part on Friday and the technician arrived on Saturday to install the part and then announces that she was willing to fix the water pump but had to get paid in cash since this was not included in the warranty. Now mind you! This woman knew about the problem from her last visit but made believe that it wasnt a problem. Advantage Appliance makes money by extorting their customers out of money. This young lady stood there without blinking asking me to pay her $89.50 to do the job she was suppose to do in the first place. I purchased an extended warranty from Home Depot only to find out that they would not be able to do anything since I was still under warranty. I have never been so angry and want Whirlpool to take responsibility. I am sitting with a washer half full with water and no one is stepping up to do something! Whirlpool is disgusting! The corporate office was not friendly or nice about this situation. They dont care! Why do businesses like Whirlpool get away with this? This is not acceptable.

I purchased a Whirlpool Washer/Dryer set in June 2014. Yesterday, Sept 9, the motor stopped working. The machine was on but nothing happened. Called the repairman who said the motor burned out and had to be replaced at a cost of $180 plus $75 for his labor. I paid around $400 for it a little over a year ago and now I have to pay $255 to get it repaired which is ridiculous for a ONE YEAR OLD machine. I will never buy Whirlpool again. I should have read the reviews first before buying but I always thought this was a good brand. Lesson learned, never buy Whirlpool.

This is one of the best washers I have had 4 years now. The spin cycle is great. Feel almost dry when done. My daughter was going to order this set but cant get them anymore. I guess it is because it is too good of a washer.

This Whirlpool washing machine is incredibly annoying and slow in everything it does. First off when you press the START button it takes 2-3 minutes before it decides to do anything, like maybe add water (except click, click and more click). If you have pressed the start button and you want to stop it to add something... again you have to wait almost 2-3 minutes before the lock is released and you can open the door. I am at 2 hrs and 15 minutes as I write this on the LIGHT WASH cycle with extra rinse and its still going. I have never seen anything like it. Cant imagine how long a HEAVY CYCLE takes. Cannot even try to measure the time. I put the load in and go to work and hope its complete when Im done 8 hrs later.We had a Maytag for 15 years with no issues (other than a drain hose cracked and had to be replaced) and it was time for a new one with a move to a new place. The sales associate convinced us this was the best machine at the time... Well what a mistake that was. There are no complaints about the actual washing. Everything comes out clean but I suppose taking that long I cant imagine why it wouldnt. I certainly cant recommend a Whirlpool washer to a friend, because I dread the thought of doing laundry at this point.

The washer (Cabrio WTW7800XWO) was less than 2 years old and we had a motor go out, so we paid a repairman to come out and repair the machine. The total cost was over $300. Now 2 months later, we get another code on the machine and Whirlpool says, We are sorry but there is nothing we can do, but if you would like to pay $219, we can get a repairman out there to check out the machine and repair it. Theyre also giving the machine an additional year warranty. Shortly after that, I noticed the lid was not staying up when I opened to put clothes in it to wash. So since I was wondering what was happening, I looked at the lid and to my surprise, the springs that hold the door up when open are built into the plastic lid cover that has a see-through glass on it. Right where the springs are located, it must be a stress point and the plastic lid has since cracked and is almost about to break off. I am now in the process of ordering another lid and Whirlpool offered to sell me a lid for $226 but I think I shall buy it from someone else as I dont want to put any more money into Whirlpools pockets. We paid over $1000 when we bought this machine. Now it is about 2.5 years old. I hope there is a class action lawsuit on Whirlpool as I will definitely join in if there is. This company needs to go out of business if they continue to sell machines like this that have so many problems especially when they are less than 2.5 years old. Goodbye Whirlpool. You have lost many more customers as I shall be letting everyone I know about all the problems and complaints about this machine.

Whirlpool Cabrio Platinum top loader 2014 model - This washer is an over engineered piece of junk. It takes forever to wash anything and it never gets anything clean. I wish I would of just bought the repair parts for my old machine which I had for twenty-three years.

I cant even tell you how disappointed I am. This washer has destroyed my clothes and towels. Ive tried to reach out to company but they want me to call for service. What would I call for? Washer works, it just makes holes in clothes, in towels. There are so many complaints about this. If anyone know how to begin a process like this, please let me know. Trust me, when I write a review about something, its got to be either really good or really bad. I dont have time to write things like this.

I bought washing machine Whirlpool Cabrio Model WTW7300XWO two years ago. It only lasted 2 years and the tub seal and tub bearing went bad. I called Whirlpool and they wouldnt replace defective part on their dime. I talked to supervisor and they still refused to admit they needed to fix this broken product on their dime and make it last longer than 2 years. They claimed only a 1-year warranty. This is totally unacceptable to have a supposedly good washer that you pay $700 for (manufacturer price $899) last only 2 years! Very, very disappointed! I wouldnt buy from this company again!

We have a Whirlpool Cabrio mod. WTW5600 XW2, ser. C12830447 he... H2O.. low wash system. Less than two years old. It does not get clothes or towels clean. I put 2 jackets in on bulky items and part of one of the jackets was still dry. They were two small childrens jackets. My husband and I wash as long as possible and on hot wash (which is not hot!). Should not take 70+ minutes to try & get normal clothes clean!Now the softener is draining into the wash with the detergent. Another service call. Learned you can only fill the softened bin half full or less. WHAT??? Our extended warranty is up soon and not sure what to do. We would like to get rid of this pile of junk but cant afford another washer bill. Also wouldnt want anyone else to get stuck with it. Its a shame a company cant put out #1 good product and #2 stand behind it. Bring all of the company production back to the USA or put out a better product and stop worshiping the almighty dollar. Im done with Whirlpool (which was the product to buy), but stuck with this washer for now until we are sure that the brand we buy performs as it should. What happened to the PRIDE in & RESPONSIBILITY of making a good product and standing by what youve made. As my hubby has said, if you have to buy an extended warranty, whats wrong with your product! Again worshiping the almighty dollar or is it you just dont care about the people who buy your product or its quality. Maybe both.P.S. Have contact you before without a response.

We just purchased this Whirlpool Washer. It is so awesome. Has all the many features I was looking for & we purchased it on sale. But really since using my washer I would buy it again even if it wasnt on sale. I love it. I have never been disappointed with Whirlpool. Everything I own in appliances is Whirlpool.

Washer is not worth the cost. After 4th year of use in a two person household the washer bearings are gone and require replacement. The washer sounds like an airplane. I was told based on my description of the issue that the water has leaked due to washing and spinning into the bearing assembly and has caused it to have friction. The Whirlpool warranty is just as costly as the machine.

I have not use wash machine for 46 years, however, since I the caregiver for my wife (with Parkinson), Im the user of our washing machine, High Efficiency Whirlpool for 8 months. It Is very easy to use including the dials. It is very efficient to use.

Whirlpool washing machine model WCW4950XW2 - We have a barely two year washing machine that we purchased at Best Buy and it no longer drains or spins. After $100 repair call we were told that this is a common problem with this model. It is a transmission problem, and with the way the machine is built a repair person cannot get into the transmission to fix it. He suggested we buy a new washing machine. This is a travesty on so many levels! If whirlpool know it has a problem it should offer a partial refund for the purchase of a newer better machine. I keep thinking about what our landfill in this world look like with the proliferation of appliances that are engineered to last a year or two. I can guarantee you I will never purchase any Whirlpool produce again, and I will research whether other brands are associated with the whirlpool brand before I buy it. Sad that a once good company has gone to hell.

I purchased the Whirlpool Cabrio washer in 2011. It has been nothing but trouble since. I have had repair people out here several times, because the machine twists and tangles the clothes, doesnt get the clothes clean. Sometimes the clothes come out dry without even getting them wet. There are lots of soap scum too. I would NEVER buy another one of these. SO DISAPPOINTED.

I purchased this Whirlpool washer (model WTW7600XW2) on October 2011. Fabric softener dispenser is full of water at end of cycle. Repairman has replaced parts three times, but the problem is still not corrected. Today, I talked with a Whirlpool supervisor. She says this is normal. She told me to take the cup out and empty it. The cup is not removable, so she said I could blot it out with a cloth or sponge. I paid $800.00 for a washer with an automatic fabric dispenser that I must empty manually. I have used whirlpool appliances for 50 years of marriage, but this is my last one. I am very disappointed with customer service.

Whirpool Product VMW TL WASHER with impeller absolutely is crap. I have it almost a year and it smells, and it noisy like a dog was in the machine and someone started it. Its off balance constantly. I hate it and will place on every blog the worst review I can write. Its a nightmare. It has a fake bleach dispenser a door but no holder underneath. Even the repairman thought the bleach went in the dispenser. My clothes were ruined along with sheets, etc on numerous washes. The bleach partially dispensed on dark clothes at least 8 washes.The washer was purchased at BrandsMart 11 months ago and so theres no returns.

I had this washer (WTW7990XGO) 5 years and finally had to replace it. It started with the touchscreen. No matter how often it was calibrated it was very frustrating to get it to respond. It would start dinging and going thru all the cycles at random times. Then there was the error code for the door lock. The door lock wasnt the problem, the surround was slightly warped and the door wasnt catching. Warped Im sure from having to literally climb into the machine to retrieve the clothes! Then a few months later it was another error code - the machine wasnt draining fast enough. It didnt drain at all. We had to use a water hose to drain it. After the second time with that, I went and bought a new washer - different brand, dials - no touch screen, and it has an agitator. Unfortunately, I ran into other customers in the appliance department who were having the same issues from 2 other brands of electronic washers. We all went back to as old school as was available.

I purchased a Whirlpool® 4.5 cu. ft. Front Load Washer with Load & Go Dispenser in 2017. By August of 2020 the washing machine was no longer working. The machine would continue to fill with water and not shut off. The machine would then give an error of E01 and F03 and drain all water within 5 minutes of the wash load starting. I had a certified Whirlpool technician come and diagnose the problem for $99. The technician said these error codes happen ALL THE TIME on Whirlpool washers. The technician tried to replace the water pressure switch with no success. He then spoke to a corporate office and was told we would have to replace the motherboard for over $500. The total cost for the diagnosis and repair was almost the exact price I paid for a new washer just 3 years earlier. I will NEVER purchase any Whirlpool appliance ever again.

These reviews re Whirlpool washer proves I can no longer trust Consumer review. This washer is junk. Does not clean, Takes over an hour to not clean your clothes. I have to add water to cover the clothes. They come out as dirty as they went in. Want an honest review? Check out the ones on Amazon.

We purchased a Whirlpool Cabrio washer in 2009. It makes awful sounds during the draining and spinning cycles, has started leaking in the past month and now, several error codes and will not finish a load of laundry. We have a family of eight and thought that we had bought a very dependable product for what we need. Boy, we were wrong!

My elderly parents had everything they own destroyed in Hurricane Sandy. After rebuilding their home, the new Whirlpool washing machine was broken. Whirlpool refused to disconnect and remove the machine that was obviously broken before it arrived. This is something that no one should have to go through. It is appalling and bad business. Through the kindness of friends, we had several male friends help with the removal. Truly shocking, that this is how Whirlpool handled this situation.

Originally, I loved my machine. At the one year mark, my washing machine began a f51 error code. I looked it up and it had a recall. The entire board had to be replaced. Now, I keep getting a ul code and it will not quit. Also, the inside of the top is rusting out so badly that chunks of rust fall into the washing machine and stain my clothes. I wish Whirlpool would fix these common errors. I see many other people complaining online that the same thing is happening over and over.

I bought Whirlpool Cabrio washer two months ago (Model number : WTW7300DW0). They indicate washer use less water and clean better, but that is not true. Some clothes on top of the load were not even getting wet and clothes smell bad after washing. Even worse is that clothes got holes in many places and some clothes were totally destroyed after washing. In just two months, I have to throw away many of my towels and clothes. I dont believe this kind of washer should be sold again. This should be a recall to give us a replacement ASAP and remove any products still in the market. There are many complaints online, I hope someone will stop this and do the right thing.

Contacted this am. See through top glass lid is separating from plastic causing sensor to turn washing machine off. Looked complaints up on this machine and it is a common occurrence and is a defect. The machine is a little over 2 or 3 years old and out of warranty. Was told not a common occurrence and I would be responsible for repair. Model # wtw7800xw2. Serial # c12270139. Thank you.

Just purchased Whirlpool top load large capacity washing machine with no agitator at Lowe’s three months ago. I sit at the kitchen table in my freshly washed exercise clothes and smell body odor. There were six exercise items in the load and supposedly enough soap. The load washed for 45 minutes last evening. Yard work clothes washed yesterday are not clean. I had to remove grass from the bottom of the tub. When I iron my smocks for work, since I work with animals, I pick pet hair off of them as I iron. Judging from other reviews, this torture won’t last long, before I need to replace this piece of junk. My last washer lasted 20 years. If it didnt leak water, it would still be running. Thanks Whirlpool, I guess the joke is on me!

Why would I, and others buy Whirlpool made washers, with all of these service problems? Now I understand why they have profit/loss statement problems, and stock prices in the pits.

I purchased a new Whirlpool Cabrio washer 3 years ago. It is the worst washer I have ever owned. During the first year it had to be repaired. It continuously flashes F51 when I try to wash a load of towels or bedding. I am beyond fed up with this machine and will NEVER purchase another Whirlpool product. If you are considering purchasing one of these I would tell you not to waste your money.

I bought a Whirlpool built washing machine on Jan. 8, 14. It stopped working on Aug. 9, 14. It is now Sept. 2, 14 and I am still waiting for it to be repaired. I am age 75 and it is difficult to load and unload clothes to take them to the laundry. The repairman order a part Aug. 26. Pony Express has not deliver the part at this time.

We purchased a Whirlpool Duet machine in September 2010. About a year ago, I started noticing tears and stains on clothing. Luckily, it was always on a washcloth or blanket, nothing special. Last week, it tore a 3-inch hole in my good jacket. I was not happy! My husband and I checked inside the drum and all around the seal. Neither of us found any rough edges. I thought if I called Whirlpool, they might have had a recall. They assured they had never heard of this problem. REALLY!!! Just look at all these e-mail complaints. Back to the old top loading - basic wash machine. Definitely not a Whirlpool!!!

I purchased a washer 6 months ago and it was starting by itself so I called to get a technician out and it took them 3 days to tell me that they did not service in our area. Long story short I was out of a washer for 2 weeks talking back & forth with Whirlpool which was absolutely a nightmare. Kept me on hold forever and hung up on me several times so they didnt have to deal with the situation. Absolutely no customer service at all. When it came down to it they were going to issue me a new washing machine and I had to go to the store to get it and when I got to the store they told me I had a $415.00 credit to spend. Thats less than what I had paid for the washing machine and then I am having to spend an extra $200.00 out of pocket to get another washing machine.My warning to you is not to purchase any Whirlpool appliances unless you want to go thru pure hell. These people do not care about anyone after the product is sold. Their customer service sucks, their appliances suck and Whirlpool just sucks all the way around!! Worst experience I have ever had and I hope they never sell another appliance again!!

As with other posts here, the rear bearing is going out of Whirlpool Duet front loading washer. I purchased mine in late 2008. Moderate use always according to recommendations. I called Whirlpool and same story--no recall and it would be expensive to have it repaired. I cant see putting $400 to $500 in parts even if I repair it myself. I cant believe that with such a common problem, Whirlpool wouldnt either honor a repair or offer a reasonable bearing package to fix. It requires the entire back, half of a new drum. Poor design, but whats worse is no effort by Whirlpool to rectify the situation.

The Whirlpool duet front loading washing machine came with our new house five years ago. That machine has destroyed multiple clothing items including very expensive sweaters and undergarments. It has destroyed biking shorts and just about anything of value. Even destroyed the bags fur delicate clothing. I have to get a repair guy out every year to replace the bellow too! It is terrible!!!

We bought a Whirlpool washer in 2010. It started making a loud noise on the rinse cycle in 2012. We called Whirlpool. They sent out a repairman from A and E Repair. Was told tub bearing shot, repair over $700.00. Contacted Whirlpool, was told machine out of warranty. After talking to them, they agreed to send parts if we paid labor. Machine lasted less than a year making the same sound again. A and E sent out same thing, bearing gone. Repair cost $997.17, charged us $136.74 service call after 2 minutes to shake the drum and saying same problem. Was told by Whirlpool, no warranty, tough luck.

Piece of junk that tears up clothes but doesnt clean. Company has ZERO care for their customers. I will never buy Whirlpool again. We called and called and called. Washer took two hours for a normal load. Crust and odors still there. Dryer was fine.

I purchased the Whirlpool Cabrio, Model no. WTW5640XW2, on March 3, 2012. I have tried every setting and water temperature and am totally dissatisfied with the washer. It does not clean clothes, tangles them into a twisted mess which requires that they be vigorously shaken out, destroys anything with a draw string. I had an online chat with a representative and was told she was sorry. I posted to Facebook and did receive a call from a repairman, which I will return; however, I do not anticipate receiving any satisfaction. The machine is worthless for washing clothes. I was better off with my 12-year old agitator Whirlpool washer. I do not understand how this machine can be allowed to stay on the market. Id be better off at the river beating my clothes against rocks. I hope someone will get on Whirlpool to give consumer refunds. I have been brought to tears by this machine and I am one tough cookie. Please help!

Whirlpools front load washers do not have easy access to the drain pump filter. The entire front of the machine including the door has to be taken off to access the filter. When putting washer back together the parts are cheap and screws break. Most companies that sell front load washers provide easy access to the drain pump filter. Buy one of those instead of a Whirlpool and you will save yourself a lot of time and hassle.

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

I bought my Whirlpool Duet set with pedestal in February 2008. I just had a tech here to figure out why my machine is so loud during agitation and that I cant hear anything else. He said its the drum hitting something. I never overload my machine - just normal use for 4 years. It costs more to repair the machine than to buy a new one. Now, after seeing this information, Im not the only one who has this problem with my Whirlpool washer. I am disappointed that there isnt anything else the Whirlpool company tech can do for me - just a receipt that shows the parts alone cost $600.00. Now, I have to pay about $50.00 just to get rid of what from the outside looks like a perfectly good machine.

This thing absolutely is total junk. It doesnt clean at all. I have to wash my sons sweaty uniform 3 times because the first two wash didnt clean it. A tub and washboard cleans better than this unit. A 600+ washer should clean the basic stuff. I remove clothes after it was finished and some of the clothes have dry spots where the water couldnt make it to. What kind of washer leaves clothes dry?I wish I came across this site when I was at the store. I did a search and the manufacture website and retail gave it positive reviews. I pretty sure the Whirlpool is paying people to write positive reviews. Technicians have come and gone telling me that there isnt anything wrong with it. That their diagnostic isnt detecting anything. Well when I call them again I will have the tech wait while I wash my sons sweaty uniform and then they can smell it after it goes through the wash. Im going call out a service tech until it works as advertise or they replace it. If I have to call them out once a week. That is what I will do.

We bought our Duet washer in 2007 with a three-year warranty. In 2010, the washer started banging so we called it in for repair. It was determined that the bearing on the drum was bad, so the entire drum assembly was replaced because the poor design of integrating the bearing into the drum. Almost one year to the day, our washer started banging again. The washer is no longer under warranty. We were told the parts are around $400 plus and another $400 for labor.The repairman was from the store we bought the washer and he is a certified Whirlpool repairman. He related to us that this is a very common occurrence for Whirlpool washers because they are using cheap foreign made bearings. He services this problem on a weekly basis and Whirlpool will not do a recall because unless it is a safety hazard, it is not a concern to them if consumers have to pay out the nose for cheaply made parts. This repairman informed us that during training at a Whirlpool class, he learned that on the main board of the washers, they could put a 2 cent lamp that would indicate a bad board which would simplify diagnosis, expedite repair and reduce service time, but Whirlpool wont do it because it isnt cost effective. The repairman told us that we can call customer service until we are blue in the face, but Whirlpool wont give a ** because it is out of warranty. He sees this happen all the time with Whirlpool. My wife called Whirlpool Customer Service just to be told we are ** even though the cheap, crappy bearing that went bad was done under warranty, a year earlier.Well Whirlpool, I guess you lost another customer who will make sure that you lose a lot more customers. We are going to take our business elsewhere and we will make sure all our family, friends, neighbors and coworkers know how bad your customer service and poor attitude is toward consumers. If you cant back your products when you put cheap foreign garbage parts in your product, then you need to lose business and get out of the market.

Our Duet Whirlpool washing machine is less than 3 years old. It would not always turn on when we would start it, or it would start and then it would give me an F70 error. If we pushed the start button again, it would continue to go through the wash cycle. There was nothing in the manual about that error. I called the service department and they could not tell me what an F70 error was either. The service department wanted to schedule a service call right away and offered me an extended warranty for $345.00, for one year. Since it was less than 3 years, and it didnt seem too serious (since the wash cycle would complete after pushing start again), I figured that it wouldnt be that much of a repair bill, so I declined. Also, I might add, that my previous 25 year old washer had only had one repair bill for a total of $200.00.When the service tech left, he handed me a repair bill for $741.00! I nearly fainted! He put in a new board. I immediately called the service department back and they said, Sorry, the extended warranty was a one-time offer and no assistance was offered when I asked. I could have bought a brand new washing machine for that price. Bottom line is, I would not buy a Whirlpool appliance again, and I would never contact Whirlpool for a problem. I would contact someone local. Had I known that a repair bill could have remotely cost over $300.00 on a new washing machine, I would have waited until it completely died and then bought a new one, and not a Whirlpool!

This Cabrio Washer and Dryer are horrible!!! Dont ever buy one, they will not fix the F1 code, and Whirlpool customer service is non existent!! I hate this company, and will never buy a product made by them again! Be aware that Whirlpool makes products for Kenmore, Maytag, and a few others!!! I just want to spread the word about this washer! If you just bought one try and take it back for something else!!! STAY AWAY FROM WHIRLPOOL!!!

It was time to put the old Frigidaire Washer out to pasture. I researched for quite some time online to find just the right new one. Its all so confusing as they all claim to be the best. The Whirlpool WTW500DW Top Load is the one I chose to look at along with 2 comparable others. I have had Whirlpool appliances in the past and was always happy with them, so I will be honest, I was leaning towards Whirlpool. I purchased the WTW500DW and matching Dryer after looking at the 2 others first. Price was lower, features were more to my liking and better quality/sturdiness was very apparent to me. This was the lower priced machine out of the 3 but had everything I wanted and a little more. The HUGE wash basket is wonderful. I have literally cut our laundry down from 4-5 loads a week to 2! Our clothes have truly never been cleaner.I am amazed at the great job this machine does with a minimum amount of time and water. It is quiet, efficient and the cycles do what they are supposed to do. The absence of electronic pad buttons is greatly appreciated. Its standard dials are easy to read and set. In my opinion, Whirlpool has done it again. Its a great Washing Machine at a price that is lower than others without as many nice features, it is well built and does the job perfectly.