My Whirlpool Gold Star aqualift oven stopped working right at three years, when the warranty ended. I paid the $650 for repairs to the stovetop, hoping this was a one-time situation. Six months later, my oven has quit. This product is not a good investment. Im very disappointed.

I purchased this machine from Sears on 04/23/2016 and have had nothing but problems and issues with it. It is loud and makes different sounds every time I use it. It has overfilled and underfilled with water a few times, the machine shuts down while washing and I have had to restart the machine. Half the time the clothes come out covered in soap and I have to put them through another rinse cycle. My bedding always has to either go through a second rinse cycle due to being covered in soap or I have to rewash it because it is all packaged together in the fitted sheet and never got washed. During the spin cycle it sounds like it is getting ready launch into outer space and it vibrates excessively. On numerous occasions I have had to untie my clothes as they are tied in knots. There have been times that I had to put the clothes through another spin cycle because the clothes contained too much water. The final straw was last week (03/27/2019). I washed my sheets and they came out bundled up in the fitted sheet full of soap stains and I had to rewash them. When the sheets were done I put the comforter in the wash and started to clean the house. When I went into the laundry room the washer was not running but the wash light was on so I opened the lid and felt the comforter and found it to be dry. I closed the lid and pushed the start button. After a few seconds the washer shifted to rinse without even washing the comforter. When the washer stopped running and the ready light came on I removed the comforter, unplugged the machine, shut off the water, disconnected the water hoses, placed the machine on a dolly and took it to my scrap pile. I could not find any Whirlpool washers with any good reviews so I purchased a Speed Queen with a 5 year parts and labor warranty.

Whirlpool Cabrio does not clean clothes and leaves white residue. I have had it for 1 year. Spent so much money on this set of washer and dryer and it is a piece of junk. Whirlpool customer service does not care or respond. Worst purchase ever.

I bought the Cabrio Whirlpool washer and dryer thinking Whirlpool was the best! Wrong! Worst washer and dryer ever! Washer doesnt get clothes clean! Leaves white residue on dark clothes! Cant put over two blankets in large tub because it gets off balanced! It wont spin water out of delicate clothes done on quick cycle! Doesnt put enough water in to wash anything! Dryer wrinkles clothes so bad I have to iron! Paid $1,200 each! So noisy you cant stay in the house when you are washing! So disappointed I will never buy Whirlpool again!!!

I have used Kenmore products for about 50 years, so when it came time to replace my old washer I looked at Kenmore/Whirlpool. I upgraded to the top of the line. I had been warned by 2 service techs (2 different companies) that had tried to keep my old Kenmore alive that the new ones are not up to par compared to the old ones. The first very small load that I tried, was not even thoroughly wet when I took it out to put in the dryer. 1st service call, tech suggested that I put machine on extra water.That helped sort of. A few weeks later, wash is not getting clean. Called Whirlpool, they suggested getting the washer cleaner and clean the washer. Went out and bought a special cleaner, $10-12 and two cleanings later using the extra water and extra wash water I now was getting cleaner clothes. They said I would need to clean the washer every 2 to 4 weeks. I have continued to use washer but frequently have to rewash about 1 in every 5 to 10 loads as it doesnt always clean everything in the load. Called the Co., they sent service out, they said its OK!In Jan. We went out of town for 2 weeks. The washer had not been used for 4 days before we left. Came home to water all over the floor which are hardwood. Needless to say our hardwood is all warped! Service came out, ran the washer for about 15 min. and said it was fine, nothing wrong! Called Whirlpool again! Washer is now out of warranty. They said call a local service, out of their hands as it is out of warranty! Nothing more than they can do.I have used Kenmore/Whirlpool Appliances all my life and they have been wonderful. The new ones are garbage as far as I can tell. I have a Refer that is now 3-4 years old and I have had problems with that, a new dishwasher that is 2ish and have had service out on that one, now my brand new washer top of the line and it is so bad I am afraid to use it unless I am sitting right in front of it watching it! Further if you have the rinse cycle on the clothes come out so wrinkled that you need to get out your iron out and iron everything including sheets and linens. Lucky that I did not replace my old dryer! Do I recommend Whirlpool anymore? Not on your life. I wish I knew what to replace them with!

Purchased washer 8/2015. Washer quit working 12/2015. Would not drain or do anything. Repairman dispatched and came 3 business days later. (They dont work weekends.) Repairman looked at old receptacle cover and immediately stated, Problem with polarity of plug. No prior problems with plug running appliances. Plugged into it for over 8 years. When I advised him of that then he started troubleshooting circuit board. He cleaned out the machine and got it to work. (Still under warranty) 4 days from repair, and machine quits. Same problem. Wont drain and wont do anything. Call for service again on Weds. morning and given following Tues for service call. Online consumer reports complaints #ered at over 1,7000. Same machine, same problems. Call Whirlpool directly, given runaround. Talk to Whirlpool mgr. (Robert) complaint # **. He states, Have to wait for service. But calls Brandt Melb., FL to try to get sooner service. Brandt calls me stating they have ordered a lid lock and CCU board for machine and will be out Monday. How would they know to order these parts if it is not a constant issue? Im thinking class action suit for shoddy product... LOWES Indian Harbour Beach, FL. Transaction #**.

Bought the Cabrio washer in March 2011. Have had the same problems as everyone else. The machine is constantly off-kilter, does not wash well due to lack of water. Sounds like a freight train when spinning. Bulky clothes dont drain properly and have to be rinsed and drained a second time. After one year of ownership, the entire control panel had to be replaced. The next year, the same control panel had to be replaced again plus a water valve had to be replaced. Thank God I bought the extended warranty. The repairs would have cost me $1000, more than I paid for the washer in 2011. Total piece of junk. AVOID AT ALL COST!!!!

Model no. WTW4950XW is a piece of pure junk. Bought this machine 2yrs, 4 months ago. I just replaced it and to be sure not with another Whirlpool. The machine went out. Just quit. Nothing on control panel (computer). Didnt call for service tech as this machine has been crap since I bought it. Tried to return it but couldnt after I first used it. It would only give hot water on 2 cycles and that was on bulk or delicate. The regular cycle would only give warm but actually it was cold. Not enough water for 6 pieces of small clothes on regular. More water on delicate. Didnt wash very well. Clothes were not really as clean as they should have been. I used to only buy Whirlpool appliances but have now switched. They are bilking the consumer with subpar machines.

We purchased a Whirlpool Refrigerator Model Number WRS555SIHZ06 Serial Number HRA2506806 on July 15th 2021 from Lowes. First one from Lowes came off the truck damaged so working out of a cooler in the kitchen for 2 more weeks. Now 4 months later the compressor is out and all the food spoiled like $400 bucks gone and food is expensive these days. I called and Whirlpool said no food allowance and no replacement. Fridge can be brought over - so repairman will come out in 6 days and then say he has to order parts then I wait two more weeks then the repair. So 3 weeks without a fridge with the holidays coming up and people to feed and food to cook. This is going to be interesting. I hate Whirlpool Refrigerator - never again will I purchase one of this appliances. The GE I had for 12 years and no problem at all for 12 years. What is going on with these companies????

I have had this range for approximately 4-5 years with no problems. The design and efficiency are great!! I would recommend this brand to anyone and would purchase it again myself. It has an extra burner just for warming which I love.

This Cabrio Washer and Dryer are horrible!!! Dont ever buy one, they will not fix the F1 code, and Whirlpool customer service is non existent!! I hate this company, and will never buy a product made by them again! Be aware that Whirlpool makes products for Kenmore, Maytag, and a few others!!! I just want to spread the word about this washer! If you just bought one try and take it back for something else!!! STAY AWAY FROM WHIRLPOOL!!!

We bought a Whirlpool washer and dryer set (Cabrio WED7300XWO) 2 years ago. Within that time, the door seal fell off and needed to be replaced. The drive belt pulley became detached, and now the drum seal has fallen out and had wrapped into the clothes. I have never experienced such a substandard product. We would trade back this one for our 15-year old set we had replaced it with at the drop of a hat. We are retired and have a summer home, and only use this product 4-5 months a year. Never again, Whirlpool!

At some point, Whirlpool should accept the fact that they should not sell this machine. Word of mouth spreads fast! Im hoping it will make a big dent in sales because I know then they will listen and act! I purchased it in 2006 for $800, thinking this Cabrio 6400SW is a dream, I can get more done in less time (at that time, there were seven in our family). However, problems within the first year, F1, but I was happy and still under warranty! It was fixed, only to start the problem again. This time, not under warranty! I really wish I had said yes to the extended warranty! Even the repair guy Whirlpool sent suggested it may be a good thing to get the extended warranty if I were you! I think he was trying to tell me something!My naive thought was, why spend more money we did not have? After all, it is a new machine! I did not comprehend that any company could sell and continue to sell something that was clearly a defective machine! Nor did I entertain the thought that a company would not stand behind their product! It is now 2012, I still have the machine because we have dealt with it and have/had no extra money to throw out at it. I have dealt with F1 for several years and did not contact Whirlpool, mostly out of lack of time to research what the deal was and if others were experiencing the same. In November 2011, after reading many complaints and frustrations on the internet and what results they got, I called Whirlpool. Using a level head, sugar sweet persona and a mindset of disbelief that Whirlpool would allow such problems, the customer service girl did her best with what she was told to reply with (meaning, there is nothing she can do). It is then that you ask to speak with a manager or director. I won in getting a repair guy out to fix the F1. They made it sound like they were doing me a onetime favor. The machine board was replaced, the repair person also thought there was an obstruction in the hose and he could fix it, but it would cost us money and suggested we try our hand at it first. We did find an obstruction and for one week, the machine was quietly working beautifully! Whirlpool even called to see about how it was working and my husband had answered that everything works well, not knowing that Ld is our new problem. Ld had started to pop up at the end of that week.So here it is July and Im so frustrated trying to get wash done. Im thinking of all the wasted time, all the wasted electricity and energy Ive spent trying to get this machine to work! My kids are trained to hit stop/pause if they hear it beeping. Some days we cant even get the clothes to spin dry. I try different cycles to get the machine to start and often have to cancel the cycle and change it to another cycle to get the machine to continue. Is there a smell? Yes, and I run the clean washer cycle twice in a row just about every other week now. That doesnt even seem to clean the washer anymore! Tangled clothes sometimes. Ld always, uL sometimes and a sound like it is trying to do something but is stuck. Lots of laundry to do! No money to fix it! Whirlpool needs to stop selling an inferior machine! I know one thing. Never Whirlpool again and I tell everyone not to go with Whirlpool Cabrio. Even one of my co-workers had one and bought a new washer (not Whirlpool) because of problems with her Cabrio only after three years! Do not purchase a Cabrio!

The microwave was easy to install above the stove and it has the exhaust fan conveniently hidden out of site underneath it. The cost was very low and it is not complicated to set up and use. I also like the fact of not having countertop space taken up by having the microwave sitting on it.

The washing machine does not wash the clothes. It does not clean the clothes and goes off balance all the time. I have had it 9 months and waited to write the review to make sure I using it properly and giving it a chance but to no avail. It is awful. It leaves white lines on the dark clothes and does not take makeup stains out of the white towels. Those are just a few examples. The clothes have to be washed sometimes twice to feel they are clean enough. So it is not cost effective and uses more water which is counter productive to the HE.

Own Whirlpool GB2FHDXWS04 refrigerator for 14 months. From the beginning, the ice maker made gross tasting ice and never got better (had to start buying ice). Then a smell started coming from the fridge every time the fan came on. We called before the warranty was up and talked to Whirlpool, and they said that we must have put something smelly in the fridge that caused the plastic to absorb the smell (which we didnt). They told us to put baking soda in and change it everyday. No change. They kept telling us there is no way it could be giving off a smell for any other reason and if they sent a tech out, we would have to pay for it. Trying to intimidate us until the warranty was up. Then after a month or so, the bottom mount freezer starts leaking water all over the wood floors every 3 days. At first we turned off the water line, but then realized it is coming when the freezer defrosts. One good thing, the freezer, from the beginning, knocked really loud and now that its leaking it doesnt knock. We spent $1,200 just over a year ago and will probably have to go purchase a new one now. I will tell you it will never be another Whirlpool product. Whirlpool has not apologized or done anything but say, Now your warranty is up, you should have bought the extended warranty. Great customer care! With all these same complaints, you would think Whirlpool would figure the problem is their inferior product (which they know) and actually take responsibility.

We purchased a Whirlpool upright frost-less freezer (model # EVL201NXRQ05) in October of 2008. So, you see, it is not even four years old. A few months ago I noticed that some things in the freezer were very soft. I looked at the back of the freezer and there was some ice buildup around the area where the coils are located. I took everything out of the freezer and removed the panel over the coils. There was major ice buildup on the coils. I completely defrosted it and dried it out. I restarted it and it seemed to be working okay. But a few days ago, when I got something from the top shelf of the freezer, it was not even frozen. So, here I go again. I removed everything from the freezer and have defrosted it again. However, this time, as soon as I turned it back on, the ice started building up on the coils immediately. It is impossible to contact anyone at Whirlpool that gives a crap. We have also been having problems with our Whirlpool Gold refrigerator. We have spent over $250 on it and it still is not working properly. I would love to just throw them in a ravine, but we have spent a lot of money on these appliances. We thought that Whirlpool was supposed to be number one in appliances. What a huge mistake we have made and it is costing us dearly.

Watery body from all the refrigerator side since 9 – 10 months and complained to Whirlpool 2 months back. They changed the thermostat 2 times but no use. Problem same. Please help. I complained during the last warranty days. Please let me know.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

Im so tired of the mold smell that never goes away, even after following their cleaning cycle many times over. I dont know what to do but I spent extra $ to purchase my washer and now this!

I purchased a Whirlpool Cabrio washer and dryer. They work well but the washer underneath lid has rusted already. I did purchase the washer in Dec. 2011 and in June 2012 the inside lid to my surprise had rust on it. I called the Whirlpool company and was told that is considered cosmetic and not covered under warranty..

The machine works well but it is extremely noisy. Large loads need to be washed twice otherwise they seem to not be washed. This machine washes small loads better. Given an option next time I will buy a front loader.

Top load stackable Washer dryer - Model number YWET 3300XQO. I had two floods with the same washer dryer unit. The first flood occurred in April 2012 and thousands of dollars were paid to repair the home that was damaged due to this flooding. The second flooding happened in October 2012 with the same machine at the same home. This time there were other Whirlpool owners that also suffered with the same issue with the same model Whirlpool machine. Whirlpool acknowledged that they will pay out to fix the damages and the deductibles but to date they are simply playing games on paying out. This is 15 months after the first flooding happened.

I purchased a Model WRF989SDAB01 Whirlpool refrigerator with the French doors and had it delivered in March 2014. The evaporator developed a refrigerant leak in May 2015. Whirlpool said it was not their problem since it was over a year since I bought it. The technician said this is a problem with this model. I am having it repaired under the extended warranty that I bought. One of my concerns is that the unit has two evaporators so the other one will probably start leaking any time. What a piece of junk. Dont buy Whirlpool. Their quality and service stinks!

After having my Whirlpool side by side refrigerator ice maker replaced 4 TIMES in 10 years, I finally found a permanent fix for it: an Igloo counter top ice maker for around half the price of a replacement Whirlpool ice maker. Unlike the Whirlpool ice maker, it makes ice. I promptly removed the Whirlpool ice maker FOR THE LAST TIME, and sent it to the dump, where it belongs. Goodbye Whirlpool! If that is the best you can produce, you will not receive any more of my hard earned money!

I am a working single man. I needed a used washer. I shopped the new washers but they were a lotta money. I seen many of them were without agitators. Well heck... who am I to judge the progress in technology?? So, going around to the used appliance store I run across this Whirlpool Cabrio. OK, Whirlpool meant quality my entire life. So, I bought it. MASSIVE MISTAKE!!! This POS is no washing machine. I dont know what it is, but it is NO washing machine! It is a machine that runs a very few gallons of water into a load of clothes and makes them wet, and that is about it!!All I know is the federal government is dropping the ball on this situation BIG TIME!! To allow a company to foist off on consumers such a PILE OF JUNK!! The pile of crap is PURE junk as far as simply doing its job... washing clothes!! It is a DISGRACE of an American product, and I will NEVER buy anything made by Whirlpool the rest of my life!!I took the device off the lid that tells it when the lid is closed, and just stuck it in its receptacle in the body... so I could raise the lid while it is running and watch this POS in action and try and figure out what the hell is going on. First big problem is it NEEDS an agitator!! Obviously Whirlpool had not figured out how to make the clothes circulate without one. Second is the water level (no matter what cycle setting) is obscenely LOW!! The clothes do not circulate AT ALL, and about 1/3 of them do not even get below water level for the entire cycle!! What I am forced to do is use a water hose and run a lot more water off into the tub just to get the clothes in the damn water!! And ever at that, the clothes still do not circulate AT ALL!! They just rub up against each other!! And I have to use twice as much soap than called for!!

I purchased this refrigerator, approximately 3 yrs. ago. Right away the top crisper broke. I have put up with this broken crisper only to have broken the PLASTIC lips that hold the crisper to the top shelf. Piece of junk. I looked to order a new crisper but way to expensive so I just suffered thru. I cant even use it anymore as I cannot open or close it without it falling onto the bottom crisper. Would like to throw the thing out, but cannot afford another one. IT WILL NOT BE A WHIRLPOOL!!!

Whirlpool Cabrio washing machine WTW8800YC0 - My washing machine that I purchased a little over 3 years ago apparently is a piece of junk. Ive noticed a smell in the past few months, even while using Affresh. Now, its making so much noise that we must close the laundry room door while the washer is on. I called customer service and they will sell me a new 1-year warranty for about $345.00. Customer service thinks it sounds like the motor or the gear box! After reading the reviews on this washer, its not worth it to repair. More trouble looms for us. Whirlpool doesnt stand behind the product and as many complaints as there are, the washer shouldnt even be sold anymore! Never buy Whirlpool!

Whirlpool Cabrio Model WTW6500 - I ask all of you to stay away from the Whirlpool Cabrio sets. I have spent hundreds of dollars trying to fix my washer. I just spent $260 for a computer board. Now it stays on rinse cycle. So now I need the motor sensor harness which is another $90. Service call $80 x 2. So, now I am going to take the computer board back and get my 260 dollars back. For the cost of $400 to fix this washer. You can go and buy a new one for around $400. Then, Im going to the lawyers to file a class action suit against Whirlpool. So, owners; be looking in your mailboxes for a class action suit against Whirlpool for those who own the cabrio set. Im tired of having to deal with whirlpool customer service. Maybe, whirlpool should think of having their laundry made back in America.

I am writing this complaint because of the very poor service of Whirlpool. My washing machine broke after 1 year of use. Luckily, I was on my 2-year insurance. The wiring fully collapsed and I needed to change the whole drum. I called Whirlpools customer service and they said that they would fix the problem after 2 weeks. They came on the day and found out the problem and ordered a new drum. They said they would fix it up on the 5th of December, and it has already been over 3 weeks. On the 4th of December, Whirlpool called me and said that the item they had ordered for me has been damaged. I am not satisfied by these products because it is only a drum (it cant break that easily). I cannot recommend this company to my friends and family due to the quality of the products and the poor customer service as I was waiting on the phone for almost an hour trying to get through.

I bought three Whirlpool appliances (fridge, gas dryer and washing machine) from Abt in June 2012, delivered in July 2012. The fridge has not cooled from the moment we plugged it in and because I am out of state from Abt (IL), I have to deal directly with Whirlpool. According to both the Whirlpool customer service rep and her supervisor, if a product is defective from the start, Whirlpools policy is to try and repair it until they determine it to be scrap and only then will they replace/refund. I find this policy appalling since I paid for a good working product, from a company Consumer Reports rates very highly, but was shipped a defective one. Now, I have had two service visits, the second because according to Whirlpool the first technician did not perform the correct service. I have been told not to put anything valuable into my freezer for 5-7 days because most likely I have a coolant leak and the fridge is bad. This is terrible customer service and instead of fixing their error which is the purpose of having customer service, they are quickly building a reputation for a terrible product and terrible service. Good customer service would be replacing the defective fridge as it is clearly their manufacturing issue, taking the item back to their warehouse, repairing it if possible and selling it as reconditioned for a discount. I am noting my suggestion in case any Whirlpool representatives read this website. Another interesting item to note is the gas dryers absorb air from the environment around them so if you do any painting (full room or touch ups), the clothes that come out of the dryer may have a burnt/gas smell for up to 7 days. I am still waiting to hear back from the Whirlpool technician as to my burnt smell problem/resolution, but was told this from a separate service representative so I thought I would pass it on.

We purchased a Whirlpool Dishwasher from the Home Depot, it was installed 3-28-2015, less than 30 days ago. On 4-21-2015 the dishwasher stopped working. I called Home Depot expecting a replacement; but we were told you have 48 hours; you need to contact Whirlpool, due to the CRAP warranty. I called Whirlpool, we were told that a TECH would need to come out and address. They came today, ** , told us that the Motor is bad. (NOTE I havent made a payment on this dishwasher). So we called Whirlpool, expecting they would replace. I spoke to ** who advised me they would not replace, only repair. I explained this is unacceptable for a new product. I demanded to speak to her Manager; Spoke to ** who said the same. I asked to speak to her manager, his name is ** , but HE DOES NOT DEAL WITH THE CONSUMERS, this is beneath his job class I was told. So NOW I have no choice but to have this Dishwasher repaired; it will take over 2 weeks to get the part. I just dont understand how this is good Customer service. It is the worst I have ever experienced.

I hate hate hate this Whirlpool Washer WTW5000DW1! To put it nicely. This is my first washer without traditional agitator and the sensing feature. I will never again buy a High Efficiency Washer with these features. It constantly gets stuck on sensing! We rearrange the load over and over and it still does not want to work. I have researched the online videos and this is a common problem. I wish I had researched prior to buying this type of machine.

We made a major appliance purchases on July 1, 2010 of a Front Loading Washer and Stackable Dryer. The dryer required servicing at 11 months with was was covered but it required a major service for a broken motor control board. This has nothing to do with regular usage. The cost to repair is over half the total cost of the appliance.This is unacceptable on a 15-month old washer. Whirlpool would not stand behind their product or service. I had to purchase their Repair Plus 1 program to get it fixed. What a racket!

We purchased a Whirlpool side by side refrigerator from a local appliance store in December, 2018. We immediately noticed a loud humming noise coming from the refrigerator when the motor is running, which is a lot. We can hear it from our bedroom on the other side of the house. The store replaced the motor and the fan, but the constant irritating humming continues. The store called Whirlpool for advice, and were told that side by side refrigerators are louder. They also said that since it is working there is nothing they can do. We had a Kenmore side by side in the very same spot for over eight years. Never noticed when it was running. We will never buy another Whirlpool product again!

Whirlpool Dishwasher is 5 years old. Used in a one-person household where dishes are washed approx.. every four days (rinsed before placing in d/washer.) Recently at completion of cycle, 2 of water remained on the bottom (still there.) Whirlpool told me it sounds like I need a new pump, the cost of which would be approx. $300 (tech visit and evaluation, parts and labor.) I understand appliances dont last forever but I expected more than five years.

We bought a new Whirlpool refrigerator from Sears last summer --- and after experiencing some motor noise we thought this would be ok. We went away to Mexico for 4 months this past winter and this spring the noise seems to be much worse. It seems to have changed -- and we called Whirlpool and they would not help. They said we pay even though we bought this fridge less than a year ago. Consumers should be made aware that if your fridge is noisy you pay for any servicing - they only cover a malfunction. My fridge needs a professional to look at the cause of the loud motor noise.

I am really disappointed because I purchased the refrigerator and now the dispenser display assembly is not working and the company does not have the replacement part to fix it. So now do I have to buy a new one???

I purchased a Duet Front Loading Washer (model WFW9750) in May 2010. In September 2011, the noise level had become intolerable. I called a local service company. They advised me that the main bearing was bad. It would cost more to repair than what it was worth. I contacted Whirlpool. They could not do anything unless the machine was inspected by one of their authorized service companies, which they scheduled. Two weeks later, A&E Factory Service arrived and confirmed that the bearing is bad and the cost to repair will be $1,542.06. Whirlpool customer service transferred me all over the country to tell me that the machine was out of warranty and there was nothing they could do.

I bought a water heater in 2008 from Lowes department store. The heater would continually go out causing no hot water. The company had sent several technical repair men out to resolve this problem, and still the problem remains. The Technical Support requested that they will pay for the part and I could install it, not knowing if I am able to do such a job. The technicians who were sent to my home were not able to do the job. How do they expect me to do the job without proper experience? Whirlpool products are not reliable nor is their maintenance contract. Stay away from this company.

Purchased a Whirlpool Cabrio washer with the glass lid. This is not a good washer to buy! The clothes do not get clean. Have to set it to bulk to get enough water to even cover clothes. Biggest issue is the lid. I have had to order a new one as it cracked on both sides back by control panel. I took the old lid off and discovered why the lid cracked. I have read many complaints about this same issue and everyone said Whirlpool would do nothing about it or even acknowledge there was a problem.Here is the problem. On each side there is a spring to hold the lid up while in the open position. The lid is plastic. When I tried to push those lid pins down with the lid off they would not go down. The springs are too strong for the plastic. When the lid is down the springs are trying to hold the lid up, so they are pushing against the plastic. Given time the springs win out against the plastic and the lid cracks and breaks. I am just a simple housewife and I figured this out! I hope that every manufacturer that is making glass top lids STOPS making them out of plastic, uses metal instead, uses a spring that is not as strong, or foregoes the current design and comes up with something that is better. It is for certain that I will never buy another Whirlpool appliance!

I purchased an HIE washer one year ago this month. I have never been happy with the cleanliness of the clothes when they came out of the wash. The only way to get them moderately clean is to wash a few items at a time and even then the whites, especially socks, seem dingy. I noticed the new Whirlpool washers now have an extra setting to add more water to the machine, so the executives have realized there is a problem with the original model.I think Whirlpool should give all customers who previously purchased the models without this feature a trade-in option to get the newer model that fills with more water or for another model with the full spindle that has worked well for so many years. I have been very unhappy with the performance of this washer and would only hope the executives would do something to resolve this problem and satisfy previous customers.

We purchased a Cabrio top loading washer (WTW6400SW2) and a Cabrio dryer (WGD6200SW1) in 2007. From day one the washer has tied clothes in knots, never cleaned the clothes properly, and sputters the detergent and bleach unevenly. The fabric softener dispenser clogs up too, rendering it useless. The knotting of the clothes leaves them so tightly wrinkled they come out of the dryer very wrinkled. The water level, determined by the washers self-sensor that weighs each load, does not fully submerge the clothes. The manual says this is normal operation for this model and that it will not affect the cleaning process. Wrong. The small agitator is insufficient to clean the clothes but does a wonderful job of twisting them in long, tight knots. I want to kick myself every time I walk past the washer for paying so much money for such a poorly designed washer. I was very sick when they were first delivered and wasnt able to do much laundry. By the time I was well enough to do more with it, I noticed the clothes werent getting clean and were actually being damaged by the washers process thanks to uneven detergent distribution/spotting from the clothes sitting above the water level, and being poorly agitated and rinsed. Before I knew it, my warranty had expired. It was a very hectic year. Ive been very sick. We purchased it from Lowe’s. I had their techs out a time or two to check it in the beginning, but they always smoothed it over with some waffy, generic explanation. Eventually, I was past my 30-day trial period. I was on my own with Whirlpool, whod refer me to the manual and make me feel like I just had to get used to the new technology of the self-sensoring washer. Ive read that Whirlpool is aware of this issue and doing nothing. Ive read other complaints that describe the same problems I have and its obvious this is a design flaw. I appreciate these posts because I least I dont feel like Im insane anymore. No, just horribly ripped off by Whirlpool.

We had Lowes install a Whirlpool model Nu40T121-403 natural gas water heater early October 2012. The temp controller went out in October of 2014. I replaced the controller myself at a cost of $30 for overnight UPS from the manufacturer, American Water Heater. The controller went out again almost exactly one year later and I again replaced it for the $30 shipping charge. In both instances the customer service person told me the malfunction was probably due to my not flushing the heater annually, causing a sediment buildup. The water to the heater not only flushed annually, but is filtered through a water softener and there was absolutely no evidence of sediment in the drain water or on the part of the control that is in the tank. Now it has stopped working a third time. I called Lowes about replacing it, but they only carry Whirlpool, so wont be buying a replacement from them.

Our new Maytag (i.e. owned by Whirlpool) oven/range is a stainless steel pile of junk. It takes FOREVER to pre-heat. The range elements take FOREVER to heat up. And like others on here, the Aqua Lift cleaning simply does not work. We put the oven through 3 back-to-back cycles and only the bottom gets a little clean. What a scam.

After the second year, everything stated to fail. The pump, the main control, even the mounting straps all failed. We are very glad we got the extended warranty. Parts alone have exceeded $400.00. Right now we are dealing with the loads not drying.

We purchased this Whirlpool refrigerator at the end of July 2018. At the beginning of November 2019 all the interior lights went out at the same time. We called the store where it was purchased, and they instructed us to call Whirlpool. Because a year had passed, they were not willing to do anything other than put us in touch with someone who could service the refrigerator. We already know the repair will cost over $200. That does not include payment for the service call or the labor. At almost the same time we purchased a new Whirlpool microwave. We have also had problems with that. My advice is to stay away from Whirlpool products if you want something that will last longer than a year.

We bought a Whirlpool Refrigerator - Model ES5FHAXS in 2006. Right off the bat, a line in the back of the refrigerator was leaking. We paid for the repair. Next after just one year, the refrigerator would be warm and the freezer part ran super cold. The settings did not work. After much haggling with Whirlpool, they paid for someone to come out and repair it. It worked for several weeks then the same problem came back again. We argued with Whirlpool again and someone from AES or AAA came out. The problem was fixed but once again came back again after a couple months. We called Whirlpool again. This time was much haggling and arguing but got them to come out a third time. Once again, the problem was fixed but came back again after several months. The repair company stated that if they found it was something other than what they fixed, we would be charged. I said either it was not fixed right or the refrigerator is a total lemon. I said you will probably just say it is something else to cover your costs. Whirlpool acted like they did enough, even though 3 repairs could not get it right. If we paid or each repair ourselves, it would have been nearly the cost of the refrigerator and it still would not have worked. We bought a refrigerator back in 1992 and never had any problems after 16 years when we moved. The refrigerator was not cheap but could not do what refrigerators are supposed to do - keep things cold all the time. What a disappointment.

Havent had any issues with it. Works great but does end up off balanced quite easily and halfway across the garage. Washes clothes like a maid. Is kinda small for bedding.

My landlord purchased a new Amana washer (NTW4605EW0) Labor Day weekend 2015. It started having issues in the spring, so we went through the process of utilizing the manufacturers warranty. Apparently, Amana, part of Whirlpool, requires 5 attempts at repairing the machines before replacing. Okay, so starting in June 2016, we arranged service appointments 5 times and replaced 1 part, then another, 4 times. Clearly, that part is defunct. Right? Fast forward to September and then into October. Get a new washer, and not the one I preferred. We got the Whirlpool WTW4816FW1. Before the installers leave, we are having the SAME issue. Stops midcycle, doesnt finish cycle, sometimes stops while filling, or while full, or kid wash, or mid drain... But now with the new washer, the drain and spin cycle thinks it should FILL instead of drain... and Whirlpool said they would get someone out the next day, a promise they cannot keep because they dont supply the repair guy, they source with local companies. So, the company ordered 3 parts... That could be the problem. And 4 days later, 2 parts are on freaking BACK ORDER. Parts arrive. All new parts replaced. Machine still doesnt work. Outlet tested by us and them and it is fine. The techs think there is some kind of RF interference. Turn off sensor light, which is on the same wall, unplug power to wifi router (which outdates the washer). Still, doesnt work.I have spent half my week, every week, since June, restarting my washer, unplugging the damn thing, waiting, and waiting, trying again and again and again to wash 2 loads of laundry a week... Literally takes a week until the damn thing does its job. Whirlpool is sent us a replacement washer. Can you guess what happened the first time we started it? SAME ISSUE. Cycle will not complete. Sometimes it dies before it even fills. Sometimes it dies while filling. Sometimes, it will fill and fill and drain and fill and fill and drain and... never stop filling. Or, the fun one, the drain and spin cycle thinks it is suppose to fill. Continuously. And then, suddenly, after unplugging it for 1 hr, or 24, or 72 hrs, it will work fine for 1-7 cycles. Nothing is consistent except that it doesnt work consistently. HAS ANYONE HAD THIS MUCH TROUBLE???

We bought the Whirlpool Gold series side-by-side about 2 years ago with an ice maker in the door and with this design, the ice bucket is on the inside of the door, which we thought was a very clever design, taking up less freezer space. Well, to remove the ice bucket, we had to use a blow dryer because even though you press the button which is supposed to disengage the bucket from the door, it has always been frozen onto the base.Then we started having issues of water leaking from the ice maker. It turns out, that the lever that controls the chute was broken. We called a certified Whirlpool technician to come out to fix the ice maker dispenser lever. Well as it turns out, it cannot be fixed. It is a sealed in the door unit and to fix it, we have to replace the door, a repair estimate for door and labor is approximately $800. That is absurd.I contacted Whirlpool and was told that my refrigerator is out of warranty and that there is not an option to repair the dispenser. There is nothing we can do. I said that according to the repairman, we are not the first to report this problem. When I contacted Whirlpool I was told there is no recall for this item. We purchased the Whirlpool based on the reputation that it has had in the past and the good product we have in a Maytag (which is associated with Whirlpool) dishwasher. Well, never again are we going to purchase a Whirlpool or any of its subsidiaries products. I have read so many unhappy customers here that I cannot believe that Whirlpool continues to make such inferior products or designs.

They attempted to fix our fridge, 1 year into owning, claimed no parts available. Never fixed, fridge died. Refused to repair. Offered us a 15% Visa gift card on another Whirlpool. Unacceptable, they can’t fix their product, and will never recommend anybody go through my familys $3,500 wasted fridge experience. Don’t trust them, they lie, and just escalate it to another liar in the customer service department.

I bought a Whirlpool washer (model wtw57esvw1) about 17 months ago. In that time, the same part has gone out three times. It happens every 5 to 6 months. The part runs 97 dollars plus labor. In the mean time, I am without the use of my washer. They say they are sorry, but they only cover their product for one year. After that, you have to buy their extended warranty so you can get it fixed by them. I feel that if I pay that much for a product I should expect at least 3 years without having to repair every 6 months! I have no washer. I am giving one star only because I have to.

We purchased a Whirlpool side by side from Lowes and an extended warranty. Immediately maybe a month the ice maker froze. Ice container in the door. Repairman said design is notorious for this problem. This was an ongoing problem. They replaced icemaker and it continued. Finally the warranty people told me it could be deemed a lemon if repaired for the same issue 4 times in a year. They deemed it a LEMON and I received a store credit for the purchase price less the warranty amount. I purchased a new LG French door. No issues and its been 5 years. If you have an extended warranty do some checking on the lemon.

I bought a refrigerator from Lowe’s and the refrigerator had a lot of manufacturing defects. I called Whirlpool and 3 techs were sent to my house. After the last tech, Whirlpool decided to exchange the refrigerator. Since then, Whirlpool has been playing games with me.

I am very sorry I bought this machine. CU rated it pretty good. Nope. 1 - It rarely dries everything completely. e.g., the collars of t-shirts or turtleneck shirts are damp after the load is finished. I have to run the machine again....Energy efficient? Energy schmefficient. and I havent even TRIED to use the low heat delicate cycle. 2 - The cute modern buttons are hard to push in. 3 - The top of the machine doesnt have a level lid... Its curved. Not very useful for setting anything on while you work at any part of your laundering process.

My 2 year old refrigerator died. I called Whirlpool and their customer service is horrible. Finally after weeks was able to purchase another refrigerator from them directly at a discounted price and they sent the wrong one. I kept it because I could no longer live without a refrigerator. Horrible company, terrible customer service and even worse product.

We bought a Whirlpool model WFW5620HW front-load washer at Lowes. The unit shook so violently during part of the spin cycle that the Whirlpool-authorized service company technician said not to use it while parts were ordered. It seems the balance ring was not functioning. Parts ordered were shocks and tub assembly. The technician suggested trying to get a whole new unit, as the repair is so intensive he had only done one or two in his career.Whirlpool customer service said they would not replace the unit, and an escalated request had the same response. I think this is terrible customer service - when there is such intensive failure in the unit, they should provide a brand new machine. The work has not yet been done - we are without use of a washer for an unknown period of time, since the order of a tub assembly is so uncommon that they do not have a time estimate. Needless to say, we will never buy Whirlpool again, and suggest you do the same.

As you have heard from 700 other people we bought a whirlpool refrigerator because GE sucks, brand new refrigerator died in 4 years with 4 service bill costing more than the refrigerator. So we did some research and whirlpool was being recommended by several stores and the reviews were better than most. Well we bought the Whirlpool refrigerator and it has been nothing but problems from the start. Everything that can go wrong has and of course our warranty ran out. And we are sitting here with no water, no ice, water tray falls out and breaks. Called whirlpool many times and their answer every time is, we will send someone out for you, and then we get a 300 to 400 dollar bill. Whirlpool sucks as bad as GE. Its crazy these companies get away with this crap. They can build good refrigerators they have in the past. My grandparents have one for 25+ years, now you cant get 2 years out of them. Pure Junk! I dont know what a good brand is anymore, they all seem to suck. Good luck.

I purchased a new Whirlpool range and had it fitted for propane. I used the stove daily and within two weeks, the temperature started fluctuated constantly. Several things I tried to cook ended up burned. I called Whirlpool to ask them for a possible solution. They wanted to send a repair person. I live on an island and knew it would take forever to get someone here. My appliance person said it could be only two things - the temperature probe or the computer board. I purchased both things and had them shipped to my address at my expense. It cost $257.00 to get the items. My appliance man on the island installed the two new items. I was hoping that would fix the problem. I am sad to say it did not! The oven still fluctuates wildly. I set the temp for 350 degrees and it shoots up to 450 degrees. I turn the temp down to 325 and it settles in at 350 for a period of time. Then, without any warning, it will shoot back up to 500 degrees. I have to open the door and let the temp back down to 350. This is how I have to bake and cook with this disaster. Wish I never purchased a Whirlpool appliance!

Whirlpool Washing machine Model WTW4800XQ1 - This machine ran fine for the first 6 months, even though my old machine took 40 minutes for a large load and this one takes an hour. Then, I had to call the repairman out and he said it was the fill valve. He didnt have one on the truck and said he should get it in within 3-5 days. Well a month later, I had to call Lowes again to find out what the problem was. They had him back out with the part within 2 days. Then, I had to call again. This time the repairman ran a test and found a bad spin motor, he had the part on truck. Third time to call and the machine is back to not spinning out properly. My old machine lasted over 14 years. Whats wrong with these new ones?

Whirlpool Energy Smart Residential Electric Water Heater - On top of this water heater is a junction box. If it goes out, so does the water heater. I am on my fourth junction box, at my expense on three of them plus the electricians bill times two. They finally sent me one free!

Whirlpool Cabrio top loading washer model WTW6800WW1 - I bought this washer 3 years ago. It cost me about $900. It has become very loud. I had the repairman here yesterday fixing my dryer. When he heard the washer, he told me the bearings are gone and its just a matter of time before the machine dies. To fix it involves a total rebuild of the motor, about $600! WTF! This is my 3rd washer in 19 years. There is something seriously wrong with appliance manufacturers. They no longer care about their reputations, and just produce crap! Expensive crap! Needless to say, I am now shopping for our 4th machine, which will be a Speedqueen basic washer with a 3-year warranty!

I bought Whirlpool top-loading high-efficiency low-water washer Sept 2018, model WTW5000DW, Serial # C83444466. Worst washing machine ever! No matter which water level you choose, it will not dispense enough water to cover the top of the clothes load, therefore the clothes are just moved from side to side with only the bottom layer of clothes getting wet; top clothes stay dry. Not enough water to fully agitate to clean the clothes!Whirlpool serviceman came today (Jan 13, 2020) to recalibrate the settings. VERY NICE MAN BUT THERE WAS NOTHING HE COULD DO TO SOLVE THE LOW WATER LEVEL. Recalibrating settings did nothing to solve the problem of not enough water. I am 81 years old and I have to manually add at least 4 buckets of water to an average load of clothes. This is unacceptable. Wont someone please initiate a class action lawsuit against Whirlpool for selling this very obvious poorly designed machine? NEVER EVER BUY A WHIRLPOOL WASHING MACHINE. It is a waste of money.

I purchased the Whirlpool washer and dryer three years ago and I absolutely wish that I hadnt. After three years of use, the bearings on the tub are shot. I need to replace them but it will cost $400.00 to repair. This is the second time that this machine is for repair. I am going to dispose this machine and purchase a new model other than Whirlpool. The overall performance is poor and not as advertised. It does not use enough water and does not wash clothes well enough. At times, you can see that the water never reached parts of the garments. I am totally disappointed in its value and quality.

Purchased Black Ice French Door refrigerator in December 6, 2012. Used warranty first year due to loud noise & replaced whole back panel in top part. They seemed to know it was a design flaw. Thought all would be well. Purchased extended warranty for second year and did not need so did not extend again. Now it has been 2 years and 7 months and the ice maker had to be shut off due to water running down outside. The refrigerator is no longer cold enough--60 Degrees (too warm) and freezer door would not close all the way (had to duct tape it shut). I certainly expected it to last longer than that for a $2300 fridge. The old Kenmore was 15 years old and still worked. After reading all these reviews it is time for a class action lawsuit! We have to buy another now but it wont be Whirlpool!

Whirpool WFW9550WW-00 Front Load Washer - Washer was purchased 08/09/12. No problems until 07/12/15 when washer stopped working mid-cycle. Motor control board needs to be replaced, actuator needs to be replaced. $500+ Our local appliance store suggested we call the Whirlpool customer relations number and ask for the parts to be sent free of charge. We would pay labor. They gave us the model number, serial number, the diagnostic info. Long story short, customer service told me she didnt know why I was told to contact them. They can not predict the life of a machine. Less than 3 years for this machine. 22 years for my old Kenmore. Our old Kenmore never had a problem, but we thought that we should replace it in 2012 in case something happened with old machine. WISH WE KEPT THE 22 YEAR OLD KENMORE.

I purchased my Cabrio a little over three years ago. Within the first month, the computer board had to be replaced and the tech informed me that it was not a malfunction in the unit; rather, it was because I did not have a sock bag for my socks and panties. I replaced the board, bought a sock bag and had no problems for about 1.5 years. A little over a year ago, the un-level started. I did research and found that I needed to replace the rods and add couplers as they were not thought of when the unit was created. This worked for an entire month. Now, I am in the same position again. It takes about 6 tries per load and the amount of water I am using is increasing with each failed attempt to wash. There should be a recall on this product. I notice there are many other complaints that match my frustrations exactly.

We moved into a new house in May 2013 and there was a new Whirlpool Gas Range installed. We have experienced an intermittent problem where the oven will not ignite since day one. We have reported it to Whirlpool and different technicians have attempted to repair it but it is still faulty. When the standard warranty ran out I purchased the Extended Warranty Protection from Whirlpool but it is WORTHLESS and they cannot fix it! The last technician from Philips Appliance in San Diego was terrible. He said he would order a new control board but never did and he closed the case without telling us.When I called Whirlpool to check on the status of the problem I was told that they will not look at or change parts for intermittent problems so what did I pay the extended warranty money for? When the oven does not ignite there is a smell of gas and we are now concerned that it may be dangerous so we are about to dump this useless Whirlpool gas range to a purchase a LG model! Bottom line is NEVER BUY Whirlpool and NEVER WASTE your money on a Whirlpool Extended Warranty Plan!

My husband and I purchased a Whirlpool Washing Machine & Dryer a year and a half ago. As of current, the machine has stopped working. The machine will turn on but will not agitate. It makes a horrible grinding noise. The type of washer we purchased was a WTW4900BW0. Whirlpool told us we should have purchased the extended warranty. But, I feel we should get more than a year and a half out of a machine that cost $650.

I have had our Whirlpool Cabrio washer and dryer (CU0771356 and MU0803512) for four years. Our trouble started when the machines were 14 months old. The numerous error codes have been fixed by replacing boards, the bearing has went out, and the entire tub has been replaced. The dryer has had two service calls for going out. Now, both are out again. The washer pump is bad and the dryer has stopped heating up. Where is the class action lawsuit?

I purchased a new Whirlpool Cabrio set, in 2009. I bought the top loading washer, and matching dryer. Since 2009, I have had the washer serviced FIVE times. Bearings, water pump, F1, F2, ul codes, and a few other things, I honestly cant remember. I love this capacity. But that is all I love about this machine. Today, the water pump went out again. I have been reading online regarding loose coins making their way into the drain pump, the hose, and other parts of the washer. I am diligent about emptying my pockets, but, obviously, someone in the house is not. There should be a trap for the coins, buttons, and any other debris that passes through, but, clearly there is not, and it appears I am not the only one with this problem. I am so frustrated. I paid almost $3,000.00 for this set. It was my very first brand new set and I have had so many problems with this. With all of the problems and all of the complaints, and so many similar complaints, why is Whirlpool not acknowledging them? Why are they not doing anything about it? Side note, my dryer works fine.

I just love the durability of my machine and the features that it offers. It does a great job washing my clothes and I feel like its a solid appliance that lasts for many years and its good quality for the price.

Purchased WRF989SDAM00 French Door refrigerator in 2013, and 33 months later it is not cooling (fridge 45/freezer 36 degrees). Service call diagnosis is a leak in the sealed component area. Since it out of the 1 year warranty period, nothing is covered. This is the first of Whirlpools dual evaporator models, and is technically challenging according to the service technician. Most likely one or both evaporators are defective, and this type of failure comes with a recommendation to change out the compressor as well as it is moisture compromised.As my previous Kitchen Aids had 10 year sealed component warranties, and the Whirlpool is the same base mechanism as the Kitchen Aid, I contacted Whirlpool to see if they would extend my warranty coverage to these sealed components. Website submission - never got an answer. Called the customer service line - they politely told me they were sorry but there is nothing they can offer me. Even the extended service plan would not cover me as this refrigerator has a preexisting problem and it must be 100% operational to begin an extended service contract.Im extremely disappointed in this fridge only lasting 33 months, in comparison to my previous Whirlpool/Kitchen Aid refrigerators. Of course the internet just allows me to see that Im not alone is purchasing a short lived appliance. So here is my contribution to the internet of things: Do not purchase Whirlpool refrigerators expecting them to last much beyond the warranty period. Buyer beware.

Our ice maker was not producing ice. Whirlpool Warranty sent a co. Kens Appliance Services to our home. The repairman diagnosed freon leak. When he came back on Oct. 7 with parts he blowtorched the electronic board & wires while fridge was plugged in. We still dont have refrigerator weeks later. We are buying food & ice every day. The next co. they sent werent licensed to add freon. He verified burnt board. Third company they sent told Whirlpool warranty to replace our fridge. They tried to sell our warranty back instead.

The refrigerator is a Whirlpool Model #GSC25C6EYW0. We purchased it on September 17, 2013. So far we had to fix the ice maker, the drawer broke, the refrigerator cools unevenly. They tried to fix it but cant. Therefore, I cannot put tall things on the top shelf. Now it is not cooling and I have to repair or replace it.

Model number wrf990slam00. I purchased this French door refrigerator in September of 2013 (less than two years ago). Our freezer stopped freezing a month ago. Knowing it was out of Warranty we had a non-Whirlpool related repair tech out. He said the compressor was going out, he said to call Whirlpool because this should not be happening on a fridge less than two years old. I called Whirlpool. They offered me a extended Warranty knowing the issue for $320 so I accepted since a compressor with labor is much more than that. Whirlpool arranged for a repair person to come out. The guy hardly looked at my fridge, didnt hook any gauges up and said maybe just see it in a few days it works again... after asking ME for a thermometer to check the temperature! I told him well we had a previous repair person out and he said it was the compressor. He said hed have to have someone else come out because he doesnt know anything about compressors. Um ok why did they send you out then! So the following week I get a call from a different guy with the same company saying my parts were in and they were going to come out and replace them. I said I thought the guy didnt know what was wrong with it. He said oh well its the compressor and evaporator! Ok well I guess comes fix it then. They came out replaced the parts. Within 36 hours the freezer was working again, ok great! Well a week later we had people over and we bought ice cream and put it in the freezer. A few hours later we pull it out and its melting. Called Whirlpool again, they sent a second company out. The guy hooked up his gauges and said it was definitely leaking refrigerant and the fibrotic in the ice maker was broken. He said he couldnt fix it because the company that replaced them is responsible for it, and that in this type of refrigerator the compressors need to be placed a certain way or they leak which he suspected that was the case. Called Whirlpool, they scheduled for the original company to come out. After 2 times of them not showing they finally came a week and a half later. The guy hooked up his gauges said it wasnt leaking and that the other guy didnt know how to read the gauges. He looked around for a bit, took my drawers out then put them back in and broke one of the brackets, then called the tech line and said its probably an internal leak. He said he needed approval from Whirlpool to look any further. A few hours after he left the refrigerator got warm. I called Whirlpool to expedite the claim and they said the company hadnt made a claim yet. Ok great. I have a two-year-old and Im pregnant and we have no refrigerator! Called the next day. Whirlpool said the refrigerator is now too expensive or not repairable and they are going to make me an offer on replacement. Ok great! Well not so much. I call a few days later to see where the heck my offer is and they tell me sorry we will only refund your Warranty What! My fridge is less than two years old and I paid $2100 and it is not repairable and thats all you will do!!!! Im in the process of fighting this but I doubt they will do anything. Just dont ever buy a Whirlpool and if you do buy the Warranty the store offers! Each repair person that came suggested the same thing and said these new Whirlpools are junk and have had many of these refrigerators do the same thing. Whirlpool makes tons and tons of money making these cheap refrigerators but does not care about the customer whatsoever! Whirlpool has lost my business forever and I hope more customers because of this review.

The product has water and ice maker problems. The day we got the new refrigerator home, it did not make ice for one week. I called and had service come out. The line was not connected properly under the refrigerator. Water was flowing out of the front of the refrigerator. I called service again and they put in a new ice maker. The ice maker was still not working. I called service and another firm came out and said the new ice maker was bad. They put in another new icemaker. Now it is making ice but will not dispense it through the door like it is supposed to. I will call service again on Monday.

Why would I, and others buy Whirlpool made washers, with all of these service problems? Now I understand why they have profit/loss statement problems, and stock prices in the pits.

Im with the rest of the people on here... The only mistake I made was not checking the reviews before purchasing a Whirlpool product. My washing machine is horrible... I dont recommend anyone purchase any Whirlpool products. Its cheap and has already stopped working twice in the last 6 months... I have had a repair man come out twice to replace the door locking mechanism... Not to mention the buttons dont work, they just slide back into the machine... Plus, you have to jump through hoops just to get the machine started the way you like it... If you make a mistake, there goes your whole ** load of laundry, not to mention the water wasted. Hell with Whirlpool - Dont ever buy a whirlpool product as long as you live.

I knew I couldnt be the only one with these problems. The reviews confirmed it. I bought my Cabrio washer in 2012. Energy efficient, no agitator to catch on clothes, Great. It took me a while to figure out that the machine was eating my clothes and not cleaning them at all. Oh, they smelled fresh. That HE detergent smells nasty. The machine ate the edges off my good towels, T-shirts, jeans. Brand new underwear (thick elastic) was stretched all the way out and pulled. Normal stains and dirt do not come out even with pretreating. I started running my clothes on the delicate cycle, prewashing stains in a bucket by hand and then putting clothes in mesh bag before running the load. They still came out dirty and ruined. When I run the loads, it still registers as not being that energy efficient on the controls. Id gladly trade it back for my old washer. I feel like I have stepped back in time to a time where you washed everything in a tub or bucket. What a waste of time.

Whirlpool N50T61-403 - I bought this thing today 8.21.14 from Lowes. It is a Whirlpool 50-Gal water heater (6th sense) and was going to have it installed by their installer, but elected after seeing it was very similar to lining up with my old unit. I got it in and then filled it. After filling, I lit the pilot light per the instructions then turned the knob for heating it up. Success, the flame spread across the burners...then went out. The steady blink changed to the 2 blink code indicating a bad thermopile. It did not work - right out of the box. No plumber near me carries the part. Whirlpool has thus been pretty good about it offering to have someone come out at their cost... But if no one has the parts, that is no good. I am moving from this house so if we can get it to work, its the problem for the next owner. If not - Ill have to get an RMA and go back to Lowes... Then try the Rheem from Home Depot. Will see if they will overnight a part tomorrow. I found the other reviews - and I dont like it that this thing appears to have difficulty right out of the box.

This washing machine was already in the house when we purchased the house two years ago. In those two years, it has performed well for the most part. It has many different cleaning options, the clothes come out clean, it saves on the amount of water it uses, it’s quiet and I like the fact that it is a front loading washer.

We purchased a brand new stainless steel refrigerator in 2013. Our 2 year refrigerator stopped producing ice and the freezer stopped working as well. We called Whirlpool customer service and they said they could not help due to 1 year manufacturer warranty only. We called another company (SoBellas) that charged us $85 to tell us that it is the seal system which should be covered up to 5 years by Whirlpool. The man showed me the Whirlpool refrigerator warranty on Google which states the sealed refrigeration parts are covered up to 5 years. There was no specific model numbers listed which gave me the impression this was a standard warranty for all Whirlpool refrigerators. I explained the situation to Whirlpool customer service including the 5 year warranty that is found on Google for everyone to see. I was told that our refrigerator model number did not qualify for that specific warranty. We ended up having to buy extended warranty for $350 on top of the $85 we already spent. This started July 24, we had to wait until August 10 for Whirlpools warranty company to see us. They checked it and said they had to order parts but he supposedly tweaked it to make our fridge run better.... It made it worse and it ended up completely breaking down. We had to buy ice chest and waited until Thursday August 27th for them to finally come back with parts and fix the refrigerator. I took time off from work once again due to our time slot being between 3 and 5 but the guy didnt even show up until 7:30. I could have worked my normal hours instead of taking more time off! The guy never once called to inform us that he was running late. We kept calling the company to make sure we werent forgotten. The guy told us that everything should be working within 20 hours or so, by Friday our freezer was still not working and no ice either, back to square one! I called Whirlpool customer service once again to explain the situation, nothing could be done. The next available time for them to come back out is September 17 for them to come look at our refrigerator. We have been stuck without ice and a freezer, buying food every other day waiting for our brand new, horrible Whirlpool refrigerator to be fixed. Will never ever buy Whirlpool brand again! Actually, we purchased all brand new Whirlpool appliances... Good luck to us!!!!!

I purchased a Whirlpool gas water heater for one of my properties that developed an issue outside of the warranty period. My initial CS complaint is with Whirlpools IVR system, which was far less than a desirable experience. After tricking the system, a CS agent answered promptly but was not able to address my concerns. I asked to speak to a supervisor and received a return call from Chris within minutes. I found Chris to be patient and understanding of my issues. Chris promptly assisted me with my issues and offered an equitable resolution. Chris is whats right with American companies and domestic customer support.

Within 5 months my 850$ dishwasher broke. 2 months to repair and 15 plus hours on the phone. Warranty is cryptic. You must allow them 30 business days from when they order parts. Buy Bosch, wish I did!

I have purchased offloading washing machine in 13 Oct. Within three years it has given lot of problems. Every third month we have to call for service and spend lot of money. We had changed drain motor and condenser. Wiring is faulty. Machine will be down many times.

I have a Whirlpool Cabrio washer and dryer set. The heating element went out on the dryer when it was less than a year old. I purchased the set at Lowes. They sent out a repair person who called and told them it was the heating element and he replaced it. Two weeks went by and I could smell something burning. I called Lowes and after two weeks wait the repairman showed back up. He said that the control panel was bad. Lowes replaced my dryer and I have not had any further issues with it. Lowes gets an A+. My washer went out about a year later. It was making the loudest noise on the spin cycle. The repair person came out about 2 weeks after I called and told me that the washer was basically worthless, that the repair would cost more than the washer would to replace. I was totally shocked and decided to use it until it died. In the meantime, I found a repair/used appliance place. They repaired it for $235 and it ran for about 4 months. Then the noise returned. I have had it repaired again. Now the control panel gives me the SE light and stops running with 27 minutes left in the wash cycle. I have had nothing but problems with this machine. I would not recommend Whirlpool to anyone. Im going to have to replace this machine and it has cost me lots of $$. Junk!!

We purchased the Whirlpool Gold Gas Range (model #GW399LXUQ06) in November 2011. Last week, I noticed the porcelain enamel finish on the stove top grates has fallen off in pieces. I contacted Whirlpool today, February 14, 2012, about this issue and they advised me it is a cosmetic problem which is not covered under the warranty. They advised me that it would cost over $100 per grate to replace. We have had this stove for less than three months and I feel these grates are defective and Whirlpool should be responsible for replacing them. I am very dissatisfied with this stove.

I was a salesperson for GE for years and thought that they made the best washer for several reasons, but eventually had to purchase another washer which was a Whirlpool. Have been very pleased with my choice and would purchase a Whirlpool again. Washer is 14 years old.

The Cabrio top load washing machine is a piece of junk, an expensive piece of junk. The only way someone could give this machine a good review is if they work for Whirlpool or they think beating clothes up against a rock in the filthy Ganges River makes them clean.We purchased the HE top loader because we were told that all the problems of the front loaders had been worked out in the new top loaders. What a joke. At least the front loader I had, cleaned the clothes. Since we got the glass top model, I made a movie that shows several items of clothes just sitting on top, not getting wet, not getting moved around, not getting rinsed; therefore, not getting clean.After the wash cycle spins down, the clothes are pinned up against the side and the rinse barely touches them before its final spin. We have several items that had stains left from the soap - yes, we used HE soap, Im not stupid. Never again will I waste my money on a Whirlpool product or anything from Best Buy.

I Purchased a Whirlpool range with self cleaning. I do not recommend anyone to purchase these ranges. The self-cleaning does not work at all. Like numerous reviews that said you can run them several times to do the self cleaning and they do not clean at all. Save your money. Do not purchase a whirlpool appliance!

Cannot reinstall oven door after glass cleaning. The worst design and absolutely no support from Whirpool. They said the instructions are in the Manual. NOT TRUE!!!. The person on their helpline said she did herself. It is simple.. Total BS. Here is the link to hope to maybe get it fixed: ** Worst stove ever.

Whirlpool Dishwasher purchased at ABC Warehouse in Chesterfield, MI and was delivered on 10-2-2014, and one year later, we noticed that the tips of the lower basket were coming off. We contacted the holder of the extended warranty (5-yr.) and also Whirlpool. Both replied the fault was cosmetic and was not covered by warranty, that only mechanical/electrical components were covered. When we were buying the extended warranty, we were told that we were covered for all issues that may occur. We werent told cosmetic flaws were not covered. I guess consumers should, before buying a new product, make a specific list of possible problems, and make sure whats covered and not covered. We have been unable to resolve this issue.

Whirlpool Cabrio drain problem - I never had a washing machine that lets so much through to the drain pump. I replaced pump three times already. First of all, if you put anything with buttons in this machine, you can kiss it goodbye. This machine destroys clothes then lets buttons and coins and whatever through to destroy the fins on the discharge pump. When is the BBB going to do something about this consumer ripoff?

I bought a gas range (#WFG524SLAB0) in July 2012. Two weeks ago, the oven stopped igniting. I called Whirlpool to have it serviced and they sent out someone from A &E Service Repair, who told me an igniter had to be ordered and it would take a week to come in. (He said he will order the part.) Then he told me to call Whirlpool again and schedule another appointment. Whirlpool sent out one of their techs two days later, who told me the same thing about the oven and said a part will need to be ordered. I told him it was ordered and he looked and said no part was ordered. So this was the week of Thanksgiving. Because the part would not be in until next week, no one could fix the stove until eight days later. So my Thanksgiving was ruined, no less with not being able to cook. So the service tech came to put the part on and the oven still is not working. He pretty much told me there was nothing he could do, for me to call Whirlpool again and have someone else look at it. I called Whirlpool and actually spoke to a supervisor who basically told me the same thing I have been hearing for two weeks: “We will send a service tech to look at the problem.” Keep in mind the stove is only four frigging months old. So here I am waiting again for someone from Whirlpool to fix my oven.

Bought this from Lowes in 2010 with the 12 yr extended warranty. Have not been able to keep it lit. Takes 4-10 days for repairman just to LOOK AT IT and then he usually has to order a new control valve, taking another 2-4 days (have had the control valve replace 3xs). This means, my husband has to get down at eye level to try to get it to light (hes 63) & if it doesnt light on the 40th try or the cramp in his hand stops him sooner, we have to heat water on the stove, carry it through the house to the bathtub, try to get the temp not too hot or too cool, then hope that our 70 yr old bodies can get down into the tub plus get back out without falling (showers are preferable). My husband bought The best hot water heater $ could buy at our local Lowes store. Because we are getting up there in years, we hoped that this would be the best answer by also getting the extended warranty. They have had numerous repairmen out to our house (6 or 7 last count)... two different men told my husband that they would only be here a couple of minutes knowing it was not going to light for them either. Time wasted. Patience gone. Still they wont replace it because if anyone can get it to light up again, no matter how long that may take, then theres no need to replace it! They have already put more money into parts, labor & repairs than it originally cost. I was told today by the ex. warranty representative that its not considered a lemon! So how do those LOWES/WHIRLPOOL people sleep at night????

It has needed a new motor, new tub assembly, and about six other repairs. Now the heavy duty tub just thumps around and I get an uneven load message, even when running empty. It is the worst single machine I have ever purchased, with the possible exception of the Whirlpool matching dryer, which lasted about three years.

This dishwasher is the most quietest dishwasher we have ever bought. Cleans even the worst messes with ease. We love all the different modes for cleaning levels. Plus in addition the ability to adjust the racks for large capacity dishes. As well the adjustment to wash fine china and crystal. We just love it!

WRF989SDAB00 - Our house burnt down in April 2012. We purchased all Whirlpool products to be put back into our house. We had to purchase these items in November 2012 so the contractor could get them into our house because of the cabinets. We did not move into our house until the last week of December and could not use these items until then. In December of 2013, our freezer went out along with the ice maker. I had to fight for Whirlpool to pay for these repairs. They kept saying that it was over the one year warranty. They did accept responsibility and paid for A&E to come look at the frig. One guy came out the first time and thought he fixed it. No. A month later two guys came out. They said it was the condenser. They ordered the parts and came back a third time to replace it. A month and a half later, same problem. A&E came out a fourth time and thought they fixed it again. Nope. During this period, I purchased a extended service plan. I AM TELLING EVERYONE TO DO THIS NOW BECAUSE IT TAKES 60 DAYS FOR THIS PLAN TO TAKE EFFECT. Now the service plan people sent a different company out and he said it is going to cost a lot of money because the things that need to be replaced. The plan SHOULD cover all of this. I called both the service company and Whirlpool demanding that they send us a replacement frig. I believe sending someone out at least SIX TIMES to fix the same problem is ridiculous. Each company is blaming the other and each is saying its the others responsibility to replace the frig.