My Maytag over the range microwave has given me nothing but troubles since my purchase. The turntable off feature never worked, and now the side control panel is barely hanging on because of broken plastic connectors. The handle is now broken in half. I will never purchase another Maytag product. Buyer beware.

Need to keep cleaning washer otherwise it leaves white marks on clothes. I used vinegar but that didnt help. Used the wash cycle and that didnt help. I found a washer cleaner and it works great. Overall performance of washer is fine but I would be hesitant on purchasing another Maytag Bravo washer only for this reason.

MBD7709AWB2 - Bottom line, every 1.5 years (18 months) you will have to buy a control panel. Number 3 for me cost me $149.00. Now my wash cycle will not kick on. Do I have to tell you what dishwasher not to buy!

Chalk up another bad tub bearing. Washer around 4 years old. Repair man says $350 to $400 to fix. Also said sees it couple times a week. Said after Whirlpool bought Maytag quality nose dived. Maytag no longer top of line. Will never buy another Whirlpool or Maytag product. Just replaced control panel on dishwasher also. Amazon sells kit to repair washer. That should tell you how bad it is. Called Whirlpool to see if they had plans to do anything about this. No they dont. Stay away.

I bought this washer less than 4 years ago and its already broken (leaking from the basket). Maytag refuses to honor their warranty and is charging $400 to send someone out to fix it even though it specifically says in the warranty that the basket is covered. When I mentioned this to the rep, I was told that does not apply to all washers. I expected better service from Maytag and thought it was a reputable company. I will now have to purchase another washer, rather than spend $400 to fix this one. It definitely will not be a Maytag!

My Daughter got me a Maytag oven with the AquaLift technology and is a piece of Junk. Half the time the Water is still there when the cycle is over. The water has made it between the front glass pieces and the finish on the top of the stove looks horrible, it just looks dirty. The knobs are cheap and the fake chrome finish is flaking off. Unfortunately Im stuck with it because I cant afford a new one... this was a gift to me because Im disabled and it was to make my life easier.

Maytag Bravos XL top load. I purchased 2014. Three years old drum bearings went out, just two people in home. Very expensive to repair. Three years later I hear bearing going out again, in mean time had a F51 pop up and that means major failure call for service. I called Speed Queen and ordered a machine with all metal parts delivered the next day, and it is Made in America. I had purchased Maytag because of name but I will never purchase another Maytag. My friend had the same experience same time frames.

This machine is the worst! I purchased this Maytag washer 2 years ago and the machine leaks from the left side bottom. I called Maytag and they said I need one of the techs out to check the machine and the cost was going to be $115 so I agreed even though was not too happy that there is no guarantee after 2 years. The service tech arrived. He could not move the machine himself and was a little angry so my wife called a neighbor to give the tech a hand after looking at the machine. He called if office to help him diagnose the unit and said the drum seal was bad and it would cost $315.00 so my wife agreed but at the end of the transaction my wife asked the technician, Is it guaranteed that this would fix it? He replied there is no guarantee but we still have to pay to try... What kind of diagnostic is this, Im very unhappy with this company. 1st the machine sucks after 2 years to start leaking and 2nd their service dept. sucks also... stay away from Maytag.

I bought this after having a Frigidaire for 40 years and was immediately disappointed upon installation. This OVEN, not a range, was smaller inside and a lot of new pans would not fit! I have replaced the burners and the bulb wiring several times. Would not buy another one!

I bought this Maytag Dryer in May 23, 2015. I had nothing but problems. I had 4 techs come out and say different reasons why it does not work. I had the vent exhaust clean out. Still not working, the one tech said there was not enough clothes for the dryer to sense it wet. I did a huge load, still doesn’t work. The sensor for the vent keeps popping up and it’s cleaned. I have to pull it out and in to get the signal light out. Cant turn on the machine. It still does not work. I tried contacting Lowe’s, since I bought an additional services plan. They said I have to call every thirty days for three months. That means I have to take my time out of work and wait for a tech for three months to get make a complaint and TRY to get new one. I really disappointed with Maytag and Lowe’s. I have a tech coming out this Monday, 11/23/2015 for another services call. I will never buy at Lowe’s or Maytag again. How many times does a certified tech from Maytag have to come out check a brand new dryer?

We purchased our Maytag 4000 series electric dryer in October 2011 from Best Buy. We did get a very good deal and have had little problems until this am. I moved laundry into the dryer and started it. While I was loading the washer, suddenly I heard a popping sound from the dryer and smelled smoke. Scared me looking into it. Sounds like either our electrical cord or our heating element blew. Coming from an era (born in the 1970s) where appliances should last at least 20 years, I am disappointed with Maytag. I shouldnt have problems at least until this thing is 10 years old. And even then I have higher expectations. So when I replace this, it will be with a better product.

My Neptune washing machine does not drain or spin. It keeps going unbalanced. I am told that I used the wrong detergent. The machine takes a whole day to wash a small load of clothes and then never finishes. Clothes and towels are constantly being ripped and torn. This Maytag product is inferior and we have paid a lot of money for this product that does not work. Repairs to this product are not advised, we have been told that we just need to buy a new one again. This is poor service and poor advice.

I purchased this washer in 2010. It has broken 4 times since purchase for the same reason. I was told by the appliance repairperson (which Maytag referred me to last time it broke on 03-11-11) that the manufacturer does not replace the machine until after it has broken down a 4th time. Now, the warranty has expired (in 09-11), and it has broken down again for the same problem - water wont fill. Sherry at call center informed me my machine does not qualify for replacement. Then, she would not give me a number or contact info for corporate office so I could forward my complaint. This machine is only slightly over a year old. I have had nothing but problems with it. I want a new machine, or at least unlimited repairs for the recurring problem. And I should not have to pay for a warranty that costs almost as much as the machine itself when Ive already paid for the machine, and at least an equal amount to the cost of the washer in repair bills just to keep this lemon on the road. I want a number and a name for someone that will listen. I may be part of the shrinking middle class, but I am a customer, and I should be treated right. Please help me.

Maytag dishwasher mdb7749awm2 - It appears that everybody who bought one of these dishwashers has run into this issue at one time or another, and it usually takes one full year of use before the control panel goes out on these units, and in most cases, it has to do with moisture getting on the thin strip of wires leading from the control board to the control panel. It usually occurs right where the strip enters the control panel... There is nice little gap for moisture to rest right on the wires, which will eventually lead to corrosion. I included an image of what to look for (see the nice black rust areas on the wires? That was my problem, and probably yours, too). If you have some very, very fine sandpaper, and have patience, then you can get the rust off the wire, but be very, very careful, or you could take the small thin wire off in the process! Ive made this repair myself to my unit, and I did it for one my friends machines (it was a Maytag, and his lasted two years, but had the same problem, too), and both had similar problems and right in the same spot! After removing the corrosion, the system worked great again. However, before hooking the unit up again, I sealed the area with some silicone to hopefully prevent this from happening again. Now, Im not saying that this is the problem that you are having, but its worth investigating, and dont be afraid to pull-off the front panel...its just held on with an adhesive and will go back on with no issues. Anyway, this could save one hundreds of dollars in repair costs. I hope that this helps.

My husband bought a washing machine in August 2019 and now it broke down a month ago. There is a sticker on it that the warranty is 10 years, but this warranty is for the motor and not for everything else. I read on the Internet what kind of error the machine gives me, it turned out to be either the motherboard or the front panel. I did not order the parts myself, called the service, in 5 minutes I had to pay 130 $ to he told me the same thing that I read in Google.... And he said that the repair would cost another 500$ part - 250$ and service fees to replace the front panel or the motherboard. Its ridiculous prices, so I find parts lil cheaper and ordered the motherboard myself, my husband installed it (there is nothing hard to do it) and the machine still gave the same error, I ordered the front panel for 220$ and the machine still gives the same error. Now front panel didnt respond at all, and this brand new panel... So I bet after I will pay to service they will tells me there is something else broken... Maytag??? NEVER AGAIN!So I send all part to the store, save money this way and now I buying a new one, when a year and a half ago I spent 1000$ on Maytag and the service is trying to rob me at the cost of a new machine, and no one gives me a guarantee after the service, I will not have a new one. The way out is possible to read more reviews and take a protective plan for 5 or more years so this is not your problem.

In the last 6 years, Ive had a Whirlpool dishwasher that the motor seized due to poor design and overseas Asian motor builder (3 years of normal service). I cleaned the motor and it seems to barely work another couple of months but the design and manufacture process was garbage at best. Thinking I would go with the best produce MAYTAG (Old commercial about repairman having no calls), only to find out that it too was bought out by CRAPPY WHIRLPOOL and it too lasted a couple of years with cheap MADE IN CHINA electronics!!! Thats why we are the laughing stock in the world as far as products.I remember the days of where built in the USA was the best of the best, now with selling our great nation down the toilet so some Wall Street Commie can make his/her biz-zillion dollars and sell this nation down the toilet. Maybe they need to go down to Arlington and see who really has paid the price for their luxurious life-style!!!

I would not recommend the Maytag washer with the large tub. It does not clean your clothes. I called Maytag and they do not care as long as it uses as little water as possible! Not a good value for the money!! That was the first time and last time I buy a Maytag... Thats the last $5000 they will get from us!

We purchased a Maytag gas range, only to have the paint wash off the front trim of the oven door. The digital panel went out in the second year of use and is apparently expensive to replace. After going through reviews by other owners and discussions with repairmen, it was determined that these panels only last about a year and are defective. This problem is extensive with Maytag. My brother was a repairman for them and dropped them due to poor quality of workmanship in appliances and their dishonest approach to warranties. I should have known better. Dont ever buy Maytag!!!

Ice maker not making ice, lights on the temperature controller are all flashing, ice/water dispenser door continuously opens and closes, refrigerator and freezer both do not cool/freeze properly. I purchased a new main control and low voltage board at a total cost of $400 and replaced them to no avail. Nothing changed when electronic boards were replaced.

We purchased a Maytag Bravos set in 2011. The dryer works great, but the washer not so much. Every load of darks comes out with soap scum all over. I use the HE detergent and most time use less than what the load should have. We have soft water and I also use softener. Ive also tried up to 3 extra rinse cycles and a smaller load size and still have soap scum all over. Im sure the light colored loads come out same, just cant see it. Needless to say, very, very upset with this washer. I, too, will never buy another Maytag product, nor will I recommend one. Had our yearly maintenance check the other day and the service man couldnt give me the reason its doing this. So, so disappointed in this product!!

I do not like this Maytag Centennial Washer at all, I have had it for a year and a half and it just does not perform good at all. Most of the time the clothes still come out with dirt on them but what I am most mad about is the fact that it keeps leaving bleach spots on my clothes, several washes after I use the bleach. I will definitely not recommend this washer to anyone.

I agree with other reviewers on this site. This top loading HE model does not get your clothes clean. Ive tried hot water, warm water, cold water. Large loads, small loads. Shirts come back with clods of dirt still on them. Pre-treating stain remover doesnt wash out of clothes. Terrible machine. I wish I hadnt bought it!

I have a basic Maytag dishwasher circa 2012. Not sure of the model number. It works well, no fancy features but everything you really need is there. My only real complaint is that the heat dry cycle always seems to leave the dishes a little wet, but thats common enough for dishwashers. It cleans nicely and hasnt had any issues or breaks in 3+ years. Basic. Three wash cycles (light, normal, heavy); Extra rinse option, extra hot option, and heat dry or eco-dry (i.e. no dry). Nice big rinse aid dispenser. Its not that roomy inside. Id say the size is average. It looks nice - its white and unobtrusive. It works really well with Cascade dish pods. The bottom rack is kind of a pain if your plates are curved more than usual.

I purchased a Maytag Bravos washer and dryer 3 years ago, thinking I was buying a high quality washer and dryer seeing that it has the Maytag name on it. When it was nine months old, I had to have the complete tub assembly replaced. Now coming upon three years old, I am having similar issues with the machine so I called out a repair service out to see what my options are. Come to find out this time that the shocks that support the tub are bad. All three of them need to be replaced at a price of $455.00. At this point, it is not worth putting the money into it. Maytag, 3 years old and I am having to start shopping for another washer. It will not be a Maytag.

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

All I ever heard was Maytag is the best so I purchased the washer/dryer over a year ago and have had nothing but trouble from the get go. It takes an hour and a half to two hours for a wash (if youre lucky). Normally, I almost always have to stop and restart it and move clothes around, babysit it. I cant wash but four or five garments at a time. Its a piece of junk and I tell everyone I talk to, never buy Maytag, ever.

My 6 year old Maytag 3000 series front load w/d set started leaking after 2 years. Minor leak on certain wash settings such as Rapid Wash setting that worsened (and I could live with), so that setting wasnt used. Last month the washer door was flapping open DURING a spin cycle. I stopped machine only to find the entire barrel had dropped and metal wire wrapped around clothing. Worst washer ever!

I purchased a Maytag Dishwasher, Model MBD7609AWW2 from our local (small) Sears store in late 2011. I purchased Maytag because of reputation and experience with the brand. In June 2014 the control panel failed. I replaced it myself and the dishwasher worked fine for a little over two months. Today, it has stopped working again and the control panel again has gone bad and has to be replaced. Sadly, the dishwasher is great in cleaning dishes. I have only had to rewash maybe one or two items in the time that Ive had it. I purchased Maytag because my previous dishwasher was a Maytag that lasted 20 years. Granted I did have to change the belt twice but it was an easy fix. Ive tried repeatedly to contact Maytag today but they are experiencing extremely high call volume... HA! I wonder why? The dishwasher was warrantied for a year and based on the experiences I have read about online, this model was apparently an absolute failure. No more Maytag anything for me... I guess the Maytag Repairman is bored because Maytag doesnt stand behind their appliances.... anymore...

I thought washers are supposed to last 10 years or something. 3 years and I have to replace it. I dont know who Im more dissatisfied with - Maytag or Direct Appliance where I purchased it. Just thought I would rant and warn others about this brand. The computer died so it doesnt know what cycle its on. Repair guy said its unfixable. ARGH!

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

I have purchased my top loader Bravos washing machine 3 1/2 years ago and I have had nothing but troubles with my machine. I have had to replace the motherboard twice and I constantly have that foul smell in all our clothes. I have to wash each load twice and still the smell doesnt come out. I have also complained numerous times about the water level not being correct, but they keep saying that is how the high efficiency machine is. I can watch my load washing because we have the clear lid which I like. But at the same time, it gets me really angry seeing how this doesnt clean clothes like it should. I dont believe that the water levels are right at all. I have clothes that dont even get turned over as they are washing and I have even smaller loads than before. I can only clean 4 adult pairs of jeans at one time and I still think that is too much. I clean my machine every time the red light turns on with the Affresh tablets and sometimes I run a clean cycle with just bleach. Maytag has done nothing to try and correct these problems. Its so sad that I have to take my clothes to the laundry mat to go wash them and there I have absolutely no problems. They have the HE front loaders and they have enough water to wash my clothes and I can actually see them being washed. I will never buy a Maytag washer or dryer again. How sad you have all these complaints and no one to help you fix or correct them the right way.

Totally DISGUSTED!!!! Have owned my range for several years! Love have double ovens, however it is double the repair!!!! Every year we must have the handles replaced as the connection loosens and handles fall off!

My over-stove microwave is approximately 18 months old. Suddenly, the fan came on and will not turn off. I had to unplug the microwave. This appliance is out of warranty but certainly should last longer than 18 months. I feel that Maytag should certainly be called to task for selling and promoting such a shoddy, unreliable product.

I purchased a Maytag refrigerator from a local business (Decker and Sons in Grand Rapids, Michigan). The fridge is a French door style with the freezer on the bottom and a water dispenser/ice maker in the left door. In the 19 months weve owned the unit weve had to have service three times. One time for the freezer door not shutting correctly, and two times because the refrigerator portion quit cooling (freezer was fine). Both times it was due to something breaking that defrosts the area behind the vegetable drawers.Both times all of our food went bad. Second time it took almost two weeks to fix (Diamond was the repair service). Now, after the service, the left door doesnt shut correctly. The quality of the unit is so questionable that I hesitate to fill it back up with food. Its just plain old junk. Luckily, we purchased a five year warranty when we purchased it...but we thought the service would be performed by the shop where we bought it, but its farmed out to other repair providers.

I purchased a Maytag Dishwasher April 6th, 2011. Its only 3 years old and now the control panel isnt working properly. Specifically, the start button. Contacted Maytag Customer Care service and they could not help me other than charging $80.00 for the Maytag Man.. which by the way, we arent suppose to see because of their superb quality in appliances. So I have a repairman scheduled for next week. I am an highly dissatisfied customer because the dishwasher is used once a week for the 3 years Ive owned it. Just a poor quality product which I will never purchase again. Model #MDB7609AWB3 Serial # F10202246.

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

I had a Maytag dishwasher for 17 years, and it has still worked fine when we moved to another state. At the end of 2010, I bought a new Maytag (1) because my old one performed so well and (2) we left it at our old house. Well, slightly over two years later, this piece of junk (Model MDB6709AWAQ1) needs almost $300 worth of repairs. The repairman said they are no longer made to last and have been that way since about the year 2000. All of the inner workings are run by electronics which only last about two years. I said, What happened; the Maytag repairman got tired of sitting around doing nothing? I would never ever purchase another Maytag dishwasher, or any other appliance made by them or Whirlpool which took over Maytag.

The dishwasher is very stylish and looks great in our kitchen. I do wish there was a small knife drawer in top. It cleans very well and is super quiet. I would highly recommend this dishwasher, good value.

I bought the Centennial top load washer and the dryer in May 2016 at Lowes. They are junk. I had a secondhand Craigslist Maytag washer that lasted 7 yrs and it was still running just fine when I got rid of it after purchasing this HE junk. The flimsy plastic door handle on the dryer fell off about 6 months ago. The clerk at Lowes assured me that the washer was high capacity & could handle heavy loads. Now I cant wash heavy loads because the agitator is already loose and getting ready to break. I have to wash smaller loads on the hand wash cycle. I cant wash my comforter or my rugs. The real kicker is I cant reach Maytag! I have tried calling to sit on hold for 30 mins to an hour. I tried the live chat during their regular business hours and it was not open. I am so disappointed in these machines. This is the first time I have ever purchased a new washer and dryer and this is what I get. I might as well have set $850 on fire. DO NOT BUY NEW MAYTAG MACHINES. THEY ARE JUNK.

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

After using my GE Profile to death we replaced it with a Maytag; mostly for the cost. Although I hate to admit this, remember the old saying you get what you paid for - Well its true at least in the case of this Maytag oven. I am a constant cook and own a bakery, I often bake many of my products at home. Since getting this oven I have had nothing but failures. The cakes are over done, underdone, cookies burnt, not cooked enough; my time frame for recipes is so off! I wrote a cook book and have baked for years so I know for a fact its not some miraculous mishap that all of a sudden I cant bake. Ive had them come calibrate the oven but still no success.Im going to call them again but I felt compelled to let people know this is the worst oven in history and avoid purchasing it at all cost. I plan on having the service team come out one last time but if this doesnt work I plan on replacing it. Its a Maytag Double Wall Oven-Top Convection-Self Cleaning model no: MEW9630DS-SS. BUYERS BEWARE!

We purchased a front-load Maytag washing machine (Model MHW3505FW1) two years ago this month. When the machine is empty, we always leave to door open. We dont allow clothes to stay in it for long, never for more than a day (the load is usually changed as soon as the cycle is over). Right now, the rubber seal on the front has tons of black mold on it, and when I lift the seal to look underneath, its way worse. There have been many problems like this reported on front-loaders. Wish Id known! Maytag will not send a replacement seal.

We bought a Maytag Bravos XL assuming that because of the brand name it would be a great machine. WRONG. This washer is truly awful. Every single load of darks comes out covered in soap scum. I always have to rewash every dark load with no soap for a full normal cycle in order to get the scum off. My whites are probably also scummy but often I just throw them in the dryer as I cant see the scum. Its just a very, very poorly designed machine that obviously wasnt tested before they started manufacturing and selling it. Its criminal how Maytag continued to sell this piece of junk, and Ill never trust their brand again.

Bought a Maytag Dishwasher (Model No. MDB7749SBM2) in Sept. 2013 and I am in need of repair for the control panel. The dishwasher is in a vacation house and isnt used on a daily basis. I always thought Maytag was a reliable product but Ive been reading the reviews and the control panel is a problem on relatively new units. How do they get away with this. The unit was around $600 and now Im stuck with a big repair bill... and it appears, from what Ive read on this site that it is a common problem. Maytag has replaced the control panel part and, as far as I am concerned, they should have provided them to all the consumers who were stuck with the defective ones they sold us in the last few years. Now we all know why we dont see the Maytag repairman sitting around with nothing to do on TV. Hes working his ass off trying to fix the dishwashers.

Purchased this maytag oven from home depot November 2011. Oven has been working properly since install. The top burner controls do operate too easy and you can just brush up against the stove and turn the gas on which I seen here was mentioned. My major issue is the stainless steel finish that was applied. It appears that this metal was not properly prepared prior to applying the finish. The oven door is with rust blisters. The metal under the coating is causing this problem. The finish in the other areas is with no problems... No chemicals have been used to clean this oven.Customer service of maytag stated that this stove only has a one year warranty... so if you buy any maytag just remember one year and when it breaks down the cost to fix will be more than a new defective maytag stove. I will not purchase another maytag product and I do not recommend that this manufacturer be considered when purchasing any appliance.

I purchased my dishwasher exactly two years ago. We are empty nesters so it has had light use. Today, when I tried to start it, the control panel would not work. Thanks to what I found in your site. I will not take a day off of work to wait for a repairman only to have it fail a second time. It is hard for me to believe a company that builds its reputation on a bored repairman would produce a product with a faulty control panel and not do something about it. Like your other folks, I will never buy another Maytag product and will not the waste the money to repair it. I am going out tomorrow to buy another dishwasher and throw this one away.

We purchased this brand new Maytag dishwasher (Model MDB7749) from Home Depot July 30, 2013. Now a little more than 18 months after purchase the control panel is out. Some lights blink, several go on at the same time. Tried resetting by removing then reinserting power plug (that worked once before, a couple of months ago,) but nothing works. Pretty much the same defect and problem I am seeing with other folks with these Maytag dishwashers. I saw online that a Sears outlet was selling these same model Maytag units for 48% off...Well, now I know why. My older Maytag appliances lasted many years. My Maytag washing machine was replaced two years ago, and it had lasted 14 years. I guess they simply do not build them like they used to. I should of just bought a cheaper model for 3-400 bucks, would of got the same use out of it. Does anybody know of a brand and model dishwasher today that is reasonably priced, dependable and has some longevity to it? I will call for service on this, but Im not spending hundreds of dollars on a defective engineering flaw, throwing good money after bad. Besides, the repair would probably only give me a 30-90 day warranty anyway. Learned my lesson. I will never buy another Maytag product again...Ever. Also I see now that they are part of Whirlpool, so they are out too. Anybody have any suggestions on a good replacement unit? Thanks...

We have a Maytag washer. It is the noisiest washer I have ever seen! It is in the garage as you could not have this washer in a house. The deep water wash is not deep enough. It bangs and knocks VERY loud! There have been times when all of the clothes are not even wet.

I bought a new Maytag dishwasher 9 months ago from Costco - Maytag 24 in. Built-in Dishwasher with PowerBlast Cycle, White. This dishwasher needs a new motor - Please do not buy this dishwasher. It is garbage.

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

Love my Maytag washer! It is great to have a clear lid so I can see the clothes being washed. Not only the features, it really cleans my clothes. I was surprised at the stains that are removed just from washing them!

I purchased a Maytag Dishwasher in April of 2011 - Ive had four control panels in that time and the panel gone again - in fact, one panel came out of the box nonfunctional (I counted that one as it was installed although the tech removed it when it quickly became apparently that it wasnt working). Ive got a complaint in to Maytag but I have low expectations as to a satisfactory conclusion. What Id like is for Maytag to buy this lemon back from me for around $400 - I paid nearly $600 (including installation). Again, I doubt this will happen. From my research online it appears that the control panel issue is a latent defect which Maytag knows about but either wont or cant figure out how to deal with it or correct it. I have a scan of the receipt which Ill see if I can upload later. I know about one class action lawsuit for CA residents. I wonder if its been expanded.

We bought Maytag refrigerator MTB2195 AEW in 2006 for a hefty sum. The store where it was purchased was closed. The place where it was serviced was closed. We have had seals replaced, fixed, etc. twice. The freezer is full of ice balls hanging. The refrigerator doesnt keep as cold as it should and stays steamed on glass. I had a repairman again today and was told that he cant fix it. The frame will not stay tight. Theres a 3/8 in. drop from left side to right. It cant seal properly. You have always been a great product. Whats happening here? What can you do for me; Im at wits end. I have an older refrigerator in the basement thats 26 years old and is still going strong. I need something done quickly as I dont want to wrangle with this ice any longer and shouldnt have to. Please give me your attention on this as soon as possible. Kathy

Does not clean laundry, leaves dry untouched spots, all my clothes look unwashed & the rinse is terrible, leaves dirt on clothes due to little water in cycle. Im a senior on fixed income. I cant buy another machine.. I called Maytag within a couple of weeks of using washer. They told me We have No guarantee for Customer Satisfaction. This is a complete scam on their part. If I could of afforded a Lawyer I would of taken them to court. They knew what they were selling & somehow got away with it. Give the people what they pay for, not the Bravos piece of Junk. Can only wash on 1 cycle to get wet wash. But paid for other useless cycles. Who made this machine & who allowed it to pass to the unfortunate Consumers. If anyone can help getting Payback from Maytag, Please let us know... Better business Bureau should get after them.

This Maytag dishwasher has been really dependable, looks really nice, is really quiet, we have absolutely no complaints. I hope it lasts as long as I suspect it will. Would highly recommend this dishwasher.

Products spoiling even if set at recommended temperature. Hard to clean bottom freezer. Not happy with this configuration. Had to have repairmen in because of stopped up drain which I could not access to clean myself. Does not close completely at times.

I purchased a Maytag built-in microwave and oven combo in 2005 for my newly built home, but I did not move into the house until 2008. So the appliance has only been used for 3 years. The microwave stopped heating after only 3 years of use, which was for microwave popcorn mostly. I also purchased, at the same time, a Maytag cooktop. The knobs had to be replaced, a dishwasher, a rack and utensil holder had to be replaced and a washer dryer that doesnt work properly. I also purchased a side-by-side refrigerator which is okay so far. Im very disappointed in their appliances and they were expensive.

I bought this washer from Lowes in 2013. It worked okay for a little while but lately it stops mid-cycle. Clothes are soaked and all of the soap hasnt been rinsed out. Poor excuse for a washing machine! Will never buy a Maytag again!

We purchased our Neptune washer and dryer combo MLG2000AWW from Circuit City in 1999 for $1900 also purchased the extended warranty. Here we are 15 years later and time to replace with new Samsung units. Besides having the main bearing replaced after 6 years in service, and having a sensor and a switch replaced on two separate occasions all covered by the warranty, our Neptune provided exceptional service throughout the 15 years. My understanding was that Maytag was bought out and run very poorly in the early 2000s as our unit was produced prior to that time... when Maytag was Maytag.

Purchased a new top loading HE washer in 9/2012. This machine gets very little use - approximately 10-12 loads a month. It is now broken awaiting parts which will cost about $200. Of course the warranty is only good for 12 months There is no excuse for a washer this new breaking and costing this much to repair. What a piece of junk! Avoid all Maytag products.

I just found this website & do not have my model info with me. But we have bought 2 Maytag refrigerators since 2001. We still have the 2nd refrigerator but I want to replace it as soon as we can. They were different models but had/have the exact same problem. They freeze up into sheets of ice and then leak puddles of water on to the floor. Makes me mad when I see their ad about how great their product is - what a load of crap! My first refrigerator was a General Electric; it was still running after 19 years when I left the farm. I still have my 2nd General Electric refrigerator (18 years old) down in my family room - running like a top! NOT EVER GOING TO BUY MAYTAG AGAIN!

We purchased a Maytag Dryer with the lint vent on top on March 21, 2014 from ABC Warehouse in Ann Arbor, MI. Whoever engineered this does not dry clothes. Trust me, this will be the last Maytag I buy. There is lint seeping out of the top and when you clean it the lint gets all over the place therefore, my laundry room is always full of dust.

My husband and I purchased our Bravo washer and dryer from Home Depot about 5 years ago. They have been the worst ever. Clothes always tear and we continue to receive an F1 error every time we try to wash something. I dont have the money to buy a new one, but I sure wish I did. I will never buy a Maytag anything ever!

I bought my black refrigerator in 2006. It has ice in the door and freezer on left side and refrigerator on right. I have not had any problem with my refrigerator and it continues to serve me well. When I need to buy another one, I will probably get a stainless that doesnt show handprints.

Bought a Maytag front load washer and dryer, it rattled and shook from day 1, they have come out 3 times in 1 month to fix that, now it wont even spin. This will be the 4th day of work I have had to miss, and all they say is, We have to send someone out to repair. Sorry. Do not purchase their products!! They dont care.

Last week I noticed that my freezer motor had a build up of frost. I melted it with a hair dryer. 2 days later there was a layer of frozen water on the bottom of my freezer as well as a layer of water on the first shelf in the fridge area. There is no way to access the drainage tube. I thought that the coils needed to be cleaned. That was not successful either since the coils run horizontal and only the front section can be vacuumed. Today, again the freezer motor area is frosted and layer of ice on bottom and the motor is making a terrible noise. How disappointing for a less than 2 year old fridge.

The control board is not working on my 2 year old dishwasher. I now see this is a common problem with Maytag dishwashers. I have called to see if there is a recall on this problem and they said no. I have been told it can cost up to $500 to fix it so I guess it is a throwaway. I should have called when it was purchased as the digital buttons didnt seem right from new. What a waste of money and I will never buy Maytag or Whirlpool.

I have a 2-year-and-5-day-old frontloader washing machine. The bearing and axle broke. The repair is over $500.00. It appears to be a known problem, as Maytag knew exactly what was wrong from the description of the noise it makes. They knew all the parts that would be needed. They would send the parts but not help with the labor. Evidently, it is a two-person job requiring several hours. They are not consumer-friendly and do not seem to care that the company reputation is going bad fast.

After 2 years the oven didnt work. I had a repair fix it for $500 but if I wanted the convection to work it would cost another $800. Obviously not worth it. Now the oven needs to be set at 400 if I want then actual temperature to be 350. Now the latest - the racks are too small and falling! I just put my Le Creuset in the oven and the rack fell. Splashed everywhere! This happened at Christmas with my turkey. So bought the fridge - everything in the back freezes. Never ever buying Maytag again. Im guessing the Maytag repairman isnt lonely anymore.

Bought a Maytag Bravo washer, suppose to be the best of its kind from Home Depot. Should of known I was in trouble when it took them over four months to deliver it. It lasted two years before the bearing went on the machine. Whirlpool/Maytag was of no help. Ironically, the machine Im using today is my old Maytag I bought 17 years ago. The repair cost for the new machine was about 50% of the cost of the machine purchase.

I am renting to own a Maytag refrigerator and it is leaking water on my floor. Runt my floor already - had to replace the floor once. Sent it back to the place where I got it for them to fix it. Paying insurance by the way that isnt worth a crap either cause they wanting to tell me that I left it open at some point or the lights was off at some point. Anyway to make a long story short they gave me the run around and didnt want to fix it. But how do you fight big companies? This was a rental company by the way rent to own so now I have 4 payments left out of 24 at 180.00 each and they still dont want to fix it. I dont know who to be madder at - the rental company or Maytag from selling this piece of junk. But by me renting to own it if any problems occurred they were suppose to fix it. Youre already paying twice the amount to get one cause of credit issues. But thats no reason to double screw someone or should I say triple cause you getting doubled the rental company alone. They need to recall this refrigerator. It has been a lot of complaint and they want to tell you to go behind the refrigerator unstop a line. Well I didnt buy this refrigerator to have to work on pulling it out from the wall every two days to do this procedure. This is crazy. Any one out there looking to buy a refrigerator my advice to you would be do your research and stay away from rental places whatever you do because you will pay twice the amount and they wont stand behind their promise either to fix it as long as you renting from them! And stay away from Maytag!!!

The bottom oven of my Maytag double oven range (serial #MER6765BAS18) caught fire while I was baking there. The coil burnt out and separated. This did not occur due to food spill or other means. The coil was charred. The stove top does not perform adequately and the coils do not heat uniformly.

I went to Home Depot in Kennesaw, Ga to purchase new W&D combo. I had found what I wanted but when the sales went to complete my order, the units I selected werent available. She talked me into the Maytag Bravo, but I specifically stated I needed a large tub because I wash a lot of towels and sheets. Well this expensive piece of shhh, doesnt even get all the items wet. Ive had to lift the lift and physically flip items in tub, especially with towels and sheets. Also, the washer is loud, did I say loud, I mean freaking loud. The dryer is fine, but I bought combo for a reason... Pricetag $1200.00 with my discount. I waited a week for delivery, I am mad as hell. Whats point of having large tub, when you barely get enough water. Luckily I found out now, so I can have them pick this CRAP UP, Do not buy. Theyre cute looking, but washer does not get your clothes clean.

Dishwasher control board - This will be the 3rd time for this same failure with the start/resume button on control panel. Obviously, with all the complaints regarding this part indicates manufacturing is producing a defective or inferior part. The service provided by Maytag, which is supposed to be a reputable company, is a joke and non-existing. Like many others, here I will gladly be part of the class action suit and will never buy another Maytag appliance and will also inform others of their poor service.

This washer had good reviews when we bought it, but now today the agitator is not working. I see there are now 100s of bad reviews of this machine most around the same 1 1/2 year mark. How unacceptable to have a large appliance like this break after such a short time. Ive called Maytag to see if there was a recall and there is not. They offered the extended warranty to me for $325 that would cover all parts and labor. Ridiculous.

Maytag French Door Refrigerator (Counter depth) #MFC2061KES14 which cost over $2,500 dollars is a DUD and the company is EVIL. The freezer leaks all over the floor and the company will not stand by their product. When I called the company they said they have had to upgrade a part called the drain tube kit because of this problem but did not put a recall. They know that this problem will occur just about the time the warranty runs out. I bet the wife of the CEO of this company has a very expensive good brand of refrigerator. Stand by your product and pay for the repairs and labor to get it fixed and put out a recall. LIFE IN AMERICA!!!

I wish that I had looked up reviews before purchasing my washer 6 months ago! No matter which setting I use, the washer never fills up with enough water!! I have pulled clothes out that havent even gotten wet, due to not enough water in machine! All due to the government regulated water levels on the sensors!!!! So, I had my plumber put in hot and cold water faucets, then he put a short Y hose on, so this way I can add water to the machine.... The only thing is, you have to wait for the machine to fill with what it thinks is enough water to get your load clean.... stop the washer, then add the water you need. But if it reaches a certain point, it will automatically start draining. So you have to watch and make sure you stop adding the water, before reaching that point!

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

I am, was, a loyal Maytag owner. The Bravos design, center hub, catches the clothes and rips the material. Customer service will only state damaged material is not warrantied. So I now have a washer that in addition to washing clothes rips them.

It doesnt agitate enough to move clothes around. Doesnt put enough water in tub, even on deep fill just barely gets to the top of clothes. Washed a shirt 3 times by myself to get dried mud off of it. 3 time it was washed bumy its self. Clothes do not to get as clean as they did in the old style washers that had good agitation and the agitator that was bigger than whats in these new ones. And water. Need water. We arent trying to dry clean. And even thats done with a liquid that totally covers clothes and moves around better than this garbage I have right now... Looking for an old washer to replace this one... HATE HATE HATE THIS WASHER.

Model # MF12269VEQ1 French doors with bottom freezer - This refrigerator was purchased March 2011 and it is forming a sheet of ice on the bottom of the freezer. We tried unplugging it overnight to see if it would correct itself and it hadnt. I googled this complaint and called the manufacturer to see if there was a recall. It seems a lot of people are having this problem. Several comments are to pour hot water in the drain plug or use a blow dryer to to the plug; however, you have to disassemble the whole bottom freezer, then unscrew the back to get to the drain plug. I feel this is a defect in this refrigerator.This unit was approx. $1600.00 and should not be having this type of problem. Who knows if I could actually get to it to try these things, that it could keep recurring. Im very upset as my husband and I are seniors on a fixed budget. We bought the name Maytag because we thought they built good products.

Purchased our Maytag Bravo Quiet Series 300 about 5 years ago and came to this site to read about other washing machine complaints because I am looking for a new washer. Was SHOCKED to hear so many similar complaints to mine (our local appliance store who sold us this unit, as well as services it, said this was unusual). Tiny holes in all our clothes! Black marks on clothes! Dirty clothes! LOUD & BUMPY washing - will sometimes walk itself around the laundry room, slamming into wash sink & dryer (there are dents to prove the violence). UL light that stops the machine & cant be resolved even after I untangle & lift water-soaked items. Finally started seeing black marks splattering out from under machine & was told the bearing is bad and the case (?) is leaking? ... Anyway, result to repair is MORE THAN ITS WORTH.Also have a 3 year old Maytag Quiet Series 300 DISHWASHER, that does not clean well, sometimes leaves half the dishes untouched (dry & dirty), grinds food waste & redistributes onto dishes before baking it on tight (requires soaking to loosen, then wash by hand) ... Oh, and is NOT quiet! I was told I probably use TOO MUCH SOAP. Seriously?!? My complaint is NOT soap residue ... It is D.I.R.T. How can you run a load and still have sauce & ketchup that dripped onto the inside of the door when loading the dishwasher STILL on the inside of the door??? Darn thing cant even clean itself!

Maytag 2000 front loading washer - This unit was purchased in Feb 2013 along with the matching dryer. From the onset it has presented with the problem of trapping small objects such as socks, underwear and other small loose objects in the rubber seal at the front of the door leaving them soaking wet and needed to be wrung out by hand. There is not any way to run a second spin only to wring out the clothes without doing an entire wash or rinse again rendering the efficiency void. I have been able to buy a mesh bag to put smaller items in for washing with the regular laundry load. However, this is not why I purchased the washer and I would strongly recommend to others not to buy this product. Very disappointed. I thought the Maytag brand was reliable. Never again will I buy any of their products.

Dishwasher cleans well but the top rack is poorly designed for taller glassware. Unit has the typical features - wash, sanitize, rinse only, high temp wash, heated dry, light, normal or heavy wash, and delay start up to 6 hours. Standard dishwasher face; nothing fancy, no dirt catching features, very satisfactory. Electronic features (start, stop, etc.) broke after very little use. This is my second Maytag and a repeat of the first. Will NOT purchase this brand again!

This washer (Model# MVWB765FW1) will not wash your clothes. Its not designed to give enough water for washing. That means some clothes will still be dry after agitator cycle; seriously. Thank you Maytag for going green! The repairman will tell you the machine is working according to design. That is true but the machine is a fraud as a clothes washing machine. The weight of the clothes in the tub tells the computer how much water to apply; good luck with that. We learned that if we add a bucket and a half of water, the clothes will come clean. Do you want to do that? Maytag used to be a good name.

So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

We purchased this microwave in Jan. 2012 to accompany a Maytag double oven for our kitchen remodel. Last night while using the microwave, 2 sparks shot up out of the top of the microwave and an electrical surge noise. I quickly un-plugged the appliance. The next day I attempted to use the microwave again and dense electrical smelling smoke poured from the top of the microwave, again un-plugged the machine. I have called an appliance repairman since the 1 year warranty is up. This machine is not even 2 years old and we will never again purchase a Maytag product. PS If the problem is the magnetron (whatever that is) I will contact Maytag for the warranty information.

The control panel went bad on our Maytag dishwasher of only 4 years that is only run about once a week, A replacement part would cost more than half of what the dishwasher originally cost, so we have decided to go with a KitchenAid. Not pleased at all with the longevity of the Maytag.

We paid over 2000.00 for our refrigerator in May 2011 and within a year ice started forming on the bottom and then leaking out on to the floor. Every week I have to get out large beach towel to lay under the pull out drawer, break up the built up ice and then pull it out onto the towel. I too called Maytag who said it was out of warranty. Now today I notice a significant temperature drop in the refrigerator and freezer. Whats odd is that the day before yesterday the freezer was so cold the ice cream was solid as a rock. I have not changed the factory settings since it was installed. I HATE MAYTAG!!!

We purchased a Maytag 4.2-cu ft High Efficiency Top Load Washer from Lowes. The pump went out within 6 weeks of purchase. Maytag could not get a technician to come to our area to fix the washer. They finally told me they would give me $150.00 for labor if I found someone to fix it. We ended up taking it to a Maytag certified repair shop. It cost us a $99.00 service fee. They ordered a new pump from Maytag, part cost 137.46. I called to get a reimbursement from Maytag and they denied my claim. Their reason I was told was because I didnt call the part in myself. I dont understand why they didnt even reimburse the $99.00. The washer was a lemon and Maytag did not honor their offer, nor the warranty. Very time consuming and bad experience.

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

I purchased a Maytag Bravos washer in 2009. I have had nothing but problems. Since, it seems that this washer was never tested nor perfected but just put on the market to sell to us, the consumers, the company does not care that this washer breaks down constantly. First the pump had to be replaced, then the tub was replaced. These were nothing compared to coins falling through to get caught in the pump and cause the washer not to drain. When I bought my washer, I also purchased an extended warranty not knowing that if the washer were to breakdown to many times, Maytag would refuse to repair under the service plan that I purchased because now they are telling me that by letting the coins fall through is abuse of the washer. Really so what they are saying is accidents will not be covered, I thought thats why we purchase insurance.Thank You, Maytag. I will never buy your product again.

I have a Model MBF 1958XES4 which I bought from Home Depot in June of 2012. It has leaked repeatedly onto my wood floor. The water also collects and freezes on the floor of the freezer. I already have warped floor boards as a result. I just got it fixed. The repair person said he has done over 200 of these repairs in the last year. He also said Maytag knows its a defect and has supplied them with replacement parts. The company apparently tells its repair companies not to discuss this with their customers. I have yet to contact Maytag, although apparently from others experiences that will be futile. Im willing to join others in pursuing this. I had a 40 year old Kelvinator which was still working well which I replaced with this refrigerator when I redid my kitchen.

I moved into an apartment home in June 2016. My apartment was furnished with all new appliances. The washer & dryer were purchased in May 2016. I live alone so on average I do 1 load of laundry per week. In November I noticed paint peeling on the inside of the dryer drum. Each time I use the dryer more paint peels. I contacted Maytag because I figured the dryer was still under some type of warranty. They sent out a technician only to tell me this was a cosmetic problem and cosmetic problems are not covered under the 10 year warranty. I would need an authorization code from Maytag if it was covered under warranty.Again, I contacted Maytag and now they want to send another technician for a second opinion. I dont feel this is cosmetic because the dryer is only 6 months old and already the paint is peeling. I feel this is a product defect because this type of problem shouldnt happen on a new appliance. I have scheduled an appointment for a second opinion and if he says its cosmetic then I have to pay out of pocket for the repairs to fix the problem. I thought Maytag stood by their product and customer satisfaction was a top priority. I guess I was wrong.

Always have bought Maytag. 16 years on both washer and dryer. The newer models, which I dont have, locks the top of the washer after it starts. I would hate that. I dont care if they are stackable but I would want full size. I dont think I would pay extra for a front loader, but the only front loading washer I have ever owned is small and at our camp.

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

This was my first Maytag, will definitely be my last. I purchased the combo washer and dryer from Home Depot in 2014. So far it has broken down 4 times needing major parts replaced. The first 2 times it broke within 3 months of owning the machine, so I called Maytag and made very irate complaints and was able to get the 1-year factory warranty extended by another 6 months. This month (May) marks the end of their extended warranty and lo and behold, the machine broke again! I called Maytag again, asking to speak with supervisors instead of customer service reps. They refused to put me on the phone with anyone higher up. I got as far as a customer service manager and she wouldnt budge. Her response was: If the machine breaks again, call us back and we will be happy to review your case at that time. I assured her that the machine would definitely break again, because it is a lemon and has broken 4 times already and wanted satisfaction NOW!! She refused to continue speaking with me and told me to call back if and when the machine breaks again. I am deeply disappointed in Maytag as a company. They had a wonderful reputation way back when, but their customer service department is sorely lacking along with selling a sub-standard product that they will not stand by. I plan on taking this matter further. I am a business owner as well as a single mom, and have no time for broken down machines and nonsense.

I love this washer. You can fill all the way or energy setting but either way it does the job. I paid 1200 for a Whirlpool. it was broken within 6 moand couldnt get service repair. With the Maytag it was on sale for 550 cash. It stop spinning. I called for service. They were there in 2 days on time and 20 minutes it was working. It was a needle stopped it. Just reprogrammed and wa-lah!

I dont know where to start. This machine (Bravo XL Top Load Washer) is ridiculous! When I finally figured out how to start it, it did not rinse or spin clothes. I cannot figure out how to get it to do that so Im stuck with a washer full of wet clothes. To add insult to injury, I cannot reach into the washer to retrieve them. I am 52 and all washers are designed by freakishly tall people with NO REGARD FOR WOMEN apparently! Poorly designed! Poorly engineered! What a piece of junk!