On 12/31/2009, I purchased a Whirlpool Cabrio, model# WTW6800WW1. I was excited as we have never spent that kind of money on a washer. We felt as though we had purchased a higher end washer and would have it for years to come. Wrong! About one year in to its use, I began to think it was getting louder during the spin cycles. I thought I was just being critical and it was just my sensitive ears. Now just past the two-year mark, I know it was not me. It’s the POS washer. It is so incredibly loud, not that you cannot be in the same room as it is during the washing time especially the spin cycle. In its defense, my clothes got cleaned.However, I know that the bearing is eventually going to give out and I will have a mandatory repair on my hands or have to pay someone to fix it. Either way, it’s a lot of time and a lot of money to fix a two-year old washer that should not need to be fixed. I attempted at getting Whirlpool to stand behind their product. No chance, no way. Good luck with that. Their washers last about 2-3 years. I will never purchase another Whirlpool product. This is a horrible product which is matched by their horrible customer service.

Oftentimes when we take out the dark loads there is a white line left. It appears to be detergent that does not go into suspension. We are using HD. Just lately we switch to liquid. Question in our minds is if it does not move the water enough to put the detergent in suspension, how in the world is it even cleaning? I do not see the turnover of the clothes. Where is the quality control with this?

On April 10, I bought a Whirlpool washing machine with a sensor. My clothes do not come clean. The dirty spots are still visible. I had three technicians come to check it out and after they just made the machine start, make the water run, and make the water empty, they confirmed that it was working normally. I have insisted on having someone come and just do a small wash and they did not agree because they are not there to wash clothes. I went back to Leon’s where I bought it and the saleslady told me that she could not do anything about it. I have been dealing with the customer service and the person has tried three times to get someone to come and check the washer properly and was insisting in front of me that I wasnt at all satisfied with the performance of the washer and still confirmed that the washer was working fine. They keep saying that there are no parts that need to be fixed or exchanged, so that means there is nothing wrong with the washer. I have tried all different kind of soaps. They were suggesting that I use Tide, which was the best performing soap. I used Tide or Purex - I even tried half a bottle of bleach - and it would not clean my clothes. The problem is the clothes are not turning, they just hardly moved with water that just keeps the clothes humid. I tried putting in more water with a bucket and when I push the start button, it would drain out all the water that it did not put itself. Ive called the consumer protection and they have advised me to take legal actions against the company and the store that sold it to me. They confirmed that whatever we buy, the article has to do the work it was made for; so the performance of a washing machine is to wash clothes. I even took a three-year prolonged warranty and the store told me that once the one-year warranty with the company has expired, then they could help me with sending their technicians and see what the problem was and they would take it from there. I have an account with the store and I have eighteen months to pay it off. So I was wondering if the saleslady did sell me an appliance saying that it was very good and that I should not have any problems with it. Can I take steps going against her for false advertisement? It’s a month now that my clothes are not washed properly and I need to rewash them by hand before putting them out to dry. The consumer protection office has been telling me that the store should be the one to finalize the problem with the company, but it seems that not even they can come to an agreement. Whatever steps I will take against the company and the store, what are my chances of getting my washer replaced? Whirlpool has been advised about me taking them to court and I got permission to do so. Actually, they invited me to go ahead and do what I thought was right. I do not have the money or time to waste on something that maybe I will have no chance to get anywhere. All I want is to have it replaced with another washer that would be more performing. If anyone has had the same problem and had their case solved, maybe it will give me hope to go on. Please, what is the best and fastest way for me to get this problem resolved? I do need a washing machine. I do need to wear clean clothes. Thank you for your patience and understanding.

When I purchased my Cabrio washer 31/2 years ago I didnt bother to check reviews since Whirlpool was suppose to be the best of the best. An expensive lesson! A washer that spits out codes?!?! Whos got time for this? We paid 899.00 plus taxes for it, now we paid a repairman 99.00 to tell us its not worth fixing. He said the bearings were completely shot. As he was leaving he said his next service call was for the same type of washer! Whatever happened to appliances that last! Going green is all the rage but yet everything from cars to appliances is built to last only a short while. Judging by these reviews I cant believe Whirlpool didnt recall their garbage!

It’s the same thing as all other reviews. The Duet washer’s eating my clothes and shaking violently, even with small loads. Forget a service call from Whirlpool - they say nothing’s wrong and I have to pay for the call. The service guy talked to me like I have never done laundry before. This is my third Whirlpool and my last. The first two were great, but the new Duet is a nightmare. Buy Samsung or LG because the Sears brands are made by Whirlpool and they are just as bad from all reviews I have read.

The washing machine continued to display an F1 error code. I contacted the manufacturer and was told that they will not do anything about the problem due to it being out of warranty. This is the first time I have complained about a product or service and want to try and assist anyone who may be thinking of purchasing a washer from Whirlpool. I do not recommend purchase of these units.

The machine purchased in 2011, 3 years old, will cost as much to repair as to buy a new one. I got exactly no satisfaction from Whirlpool. They said there is no recall so they wouldnt assist. There are only 2 people in my house, so how could the washer be so junky. What would a large family do? I have spent $140 and wont spend another dime on a Whirlpool appliance.

I have had the washer for 3 years now and it started to make a loud noise during spin cycle. I made a service call and found out the bearings are damaged. Something that cost this much money should last a lot longer. I have researched on the internet and found this to be the problem for a lot of consumers and would like to see something happen.

My machine has been ripping clothes for a few years but I thought, initially, that it was a snap, zipper or hook causing the problem. I recently got fed up and found this: **. It makes it pretty clear that it is a manufacturing defect. I called their customer service centre and spoke to a supervisor that told me it is normal wear and tear and that perhaps the glass in the door had worn out. Yes, thats right, she said maybe the glass has worn out.They are offering ZERO assistance in what would be a $500+ repair for me. Admittedly, my machine is five years old and out of warranty, but to me, when the repair is to install an entirely new style of door so that the clothes no longer get caught underneath, it is a defect. 43 different models of their machines are included in this issue and it was identified in 2012, a year before my machine was made. Why didnt they correct it before that?

My whirlpool Cabrio washer top load had the rust problems, bearing problems, support arms replaced along with the complete drive assembly motor bearings and all the parts. My bearings have failed 3 times since 2009. This machine is junk. Customer service at Whirlpool is a joke. They treat you as if you have had to do something wrong. Finally I spoke with a salesman who said speak with the warranty company. I have the extended warranty which I advise everyone who purchases an appliance to get one. So I spoke with them and they sent me a check for a new machine. I must say our warranty company has been very helpful. So THIS IS MY WARNING TO ALL. PLEASE DO NOT BUY FROM WHIRLPOOL. IF YOU DO YOU DESERVE WHAT YOU GET, SORRY TO SAY... Have a great day.

I have a Cabrio washing machine and the circuit board has gone bad. I understand from Whirlpools customer service that if your machine was made before 2005, they are fixing the issue. Mine was made after 2006. Even though the problem is the same, Whirlpool will not correct the problem. I was told it was fixed in the new machines. The circuit board goes bad and you have to start and stop the machine at least three times before it will start your cycle, then it stops again at the 17 minute mark and you have to cancel and start the machine again for it to finish its cycle. The error is F1. Customer service acknowledged that this is a known problem for the Whirlpool machines built before 2005 but deny any claim that is is happening to the machines after 2005. Looking at all the other complaints, it is still a problem. I am disappointed in Whirlpool for their customer service attitude and for them not standing behind their product and fixing a known problem. I have always bought Whirlpool products but going forward will be switching to a better company. Shame on you Whirlpool. For a machine I spent $1000 on, the part is going to cost $300 to fix.

Do NOT buy the Whirlpool Cabrio washer...it doesnt actually wash your clothes! Most clothing still half dry after the wash (didnt get any water on them) and they are still smelling sweat after the wash! Also doesnt clean basic stains that others washers clean. Even if you add water manually to the washer to soak your clothes, the clothes on top wont be agitated at all, hence the reason the clothes are still dirty after a wash. Poorly engineered washer... its a lemon as it doesnt do what it is supposed to do (wash clothes). Biggest scam ever from Whirlpool and shouldnt be allowed to be sold to consumers anymore!

Purchased this washer new 2015 for use in our cabin. Now 4 years later with very little use the motor has seized. Washer is useless. What happened to 20 years of almost daily use and still runs great. This washer is a very poor quality washer and has now failed. Please save your money and buy a different brand.

Whirlpool Cabrio Top Load Washer Model: WTW7800XWO purchased at Lowes 8/26/2010. The lid was broken at the hinge in less than a year and was replaced under factory warranty. Lid falls down and pinches fingers. The second lid broke in the same location in less than a year. Lid falls down and strikes the eye. I’m speaking with repair technicians and researching complaints on this product. It appears to be a design defect that is not being addressed by the manufacturer.

We purchased a Whirlpool Cabrio model # WTW6400SW3 in 04/08. Approx. 6 months ago, the washer started to be un-level during the spin cycle. This has progressively become worse, it now becomes un-level during the rinse cycle. We spoke with the appliance store where we purchased it, ;hey said the repairs could cost $400 or more. Thats nearly half of what it cost new. Like other complaints Ive read, cheaper washers have lasted years longer than the Whirlpool. Our last washer, a Kenmore, lasted 15 years.

I have the 4.3 cu. ft. washer. This washer worked OK, but the lid lock does fail after about one year if the washer is in an environment where moisture may be present.I noticed the lid lock not working all the time about two months before the warranty expired. If this happens, call the warranty department immediately. After checking the ground wire and resetting the washer power over and over again, the lid lock finally stopped working completely. Here is how to fix it:There are two screws on the back of the top portion of the washer. Unscrew them from the silver straps. The washer lid will now push forward and up and off. Prop it up with a stick.Unscrew the two screws on the lid lock and start taking it apart (after reading this entire review). Be careful not to lose any parts and be sure to know where everything goes for re-assembly. Take pictures if necessary. Take the lid lock completely apart including any small pieces.The plastic slide needs to be cleaned. It has a spring that may fall when you pull it apart.The metal contact points inside the lid lock mechanism need to be cleaned. Be extremely careful when pulling the red cover off of the housing assembly. Pull the four metal contact points completely out of the plastic assembly. Be real careful with the black plastic slide piece, the metal rocker switch and the switch actuating motor. Use a small file and rubbing alcohol to clean off any green or white corrosion. Make sure to check all contact points.Re-assemble and you will immediately notice the lock switch working better. Re-install onto the machine. Re-install the upper portion of the washer. Start your laundry. Repeat after one year or when the lid lock becomes faulty again. These points should have been made out of a less corrosive material. Poor craftsmanship. Would not recommend.

Front load is terrible. Doesnt wring clothes thoroughly. Runs for 1 hour on fastest cycle. A HUGE WASTE OF ENERGY! NOT A GOOD MACHINE!!! Our clothes are wet always after the spin cycle. It also doesnt do small throw rugs. Awful!

I saw on the Today Show that my Whirlpool Duet washer, purchased in 2008 was a mold-producing nightmare. We are now part of a class action lawsuit that seeks redress. When I called Whirlpool Customer Service, I was fed the company line that the problem is that we dont clean the machine regularly. The instructions call for monthly maintenance, but the rep said we need to wipe it dry after each use. This is an original defect in the machine that Whirlpool refuses to own up to. We had been Whirlpool devotees for years but will never purchase another Whirlpool product.

A-10 error on display ultimately means needs a new pump. The washer (model WFC7500VW 2) is 3 months, 9 days old and is now unusable. I cannot get any service (under 1-year manufacturers warranty) because the sticker inside the door with the model and serial # is missing (i.e., it was sold to me by Homedepot.com without a serial # on the door label, sticker is intact and is brand new and apparently was printed without a serial #).I made multiple calls to Whirlpool in Benton Harbor, Michigan and finally spoke with Courtney (who states she was a supervisor) pretty much said all they will do is to reprint a label from the factory and I should have it in 7-10 business days. They refuse to stand behind their product and authorize timely repair of their product they sold to my without a serial # on the door tag from the factory. I have to wait to schedule factory warranty repair until I get the new label (probably 3 weeks plus without a usable washer). Courtney refused to contact me via email for any of her contact information or to supply verification of conversation or promise of a new factory label. Also, she refused to try to authorize any type of manufacturers warranty to fix the brand new unusable washer!

The first Front load Whirlpool washer leaked. 5 repair techs visits. Wasted days. Finally located the leak, in the main basket. Replaced washer. Second washer the clothes come out smelling like a horse blanket. Mold. Clean the washer every month still mold. Plan on junking the washer a getting a new model. Never expected this much trouble and time on a basic appliance.

Whirlpool Cabrio washer - Its very expensive and it quit after 3 years. Repairman said computer component went out and it would cost $450-$520 to repair and it wasnt worth it. He also told me I should have read reviews first. Whirlpool said I should have bought extended warranty. No more Whirlpool appliances will be bought for our homes or business.

My elderly mother purchased a Whirlpool Washer Mode Number WTW4955HW1 in November 2020. The washer has had nothing but problems. It leaks, vibrates and moves on the floor. My mother called Home Depot to see what she needs to do, and they said once they deliver the product it is out of their hands. Had our first service call in May 2021 by an authorized service and he said they should sell this on eBay. It is a horrible product, he said there is nothing he can do. Had a second authorized service in June 2021 and they said we needed a new tub which they ordered, and he said this will take up to 2 months, they also said to do only small loads and only use the deep-water wash and deep water rinse. After the technician left the agitator now comes apart. Would not recommend this product to anyone and I would never buy anything at Home Depot because they do stand by the products they sell.

We bought this washer from Sears with big hope. Within the first year, we had 14 service call covered by the warranty but required 2 to 3 weeks in doing without. Whirlpool replaced the washer at no charge but continued to have various issues over the years. The new one is the control module that Whirlpool knew was faulty but did not let their customers know. The control module went over the weekend but I repaired it myself and do not have any more issues. I literally went in and tightened all of the hardware, removed and install the pulleys, motors pumps and replaced a lot of keep components with better quality. Guess that year the CEO made only 20 million rather than 19 million. Being an American company I was disappointed by the consumer relations people but everything is a throw away nowadays. Will not buy a Maytag or Whirlpool product again. Where has American product pride gone?

We purchased a front loader Duet in August of 2011. It is now January 2013 and we had to have a service person come out. We did not buy the extended warranty because a washer should last longer than 1 year 5 months, but not ours! We need to have the drum replaced at $600. Are you kidding me! I will never buy another Whirlpool product.

Rust started forming early on our washer and spread quickly. Our house is air conditioned and not near the ocean. There was no reason for the rust. Poor quality finishing is the only explanation. When I called to complain I got nowhere. I wish I could show a photo on this website. It would dissuade anyone from ever buying a whirlpool.

Purchased a Whirlpool Cabrio washing machine from Sears in August 2010. Last week, while my wife was washing clothes, we smelled smoke and the washing machine stopped working in mid cycle. Called Sears repair and came out Saturday 10/10/2015 to inspect the machine. When the repairman checked the codes he determined there was a problem with the motor. When he lifted the machine up the capacitor fell out in 2 pieces. It had blown apart and the motor had burned up. The estimated repair bill was $480.00. Needless to say we did not repair the machine. We will never buy another Whirlpool product or any other product that they manufacture under a different name.

I love my Whirlpool. Were a family of 3 with a pet dog. Its handle one childs work uniforms and the others sports uniforms (yuck). And then theres my work/weekend clothes. Its very reliable and it gets the job done. We have no complaints.

I purchased the Whirlpool Cabrio (wtw6600sw2) about five years ago. Last year, the motherboard had to be replaced. This year, it started to have load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $75 to have someone look at it, and to fix it will cost almost $400, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. I called Whirlpool and my model does not have a recall, but models with same problems have been recalled. I will never buy a Whirlpool again!!!

Cabrio washer Model # wtw5840bw - I purchased this washer one year ago. It has a defect that comes along with it. You think your clothes are getting clean. But in reality they are not. This washer does not fill enough water to wash a small load of clothes. It has ruined three large bags of my clothes. Stained they smell in general they are not clean. Worst washer I have ever bought. General public Please be aware of this issue if you are going to purchase this washer. It is a big expense to be put out to the curb.

From the time I had the Cabrio top load washer, it has been repaired at least 8 times. I did get the extended 2-year warranty. I should have known that this machine was going to give me problems from the first service call. I have had to have the motor replaced 4 out of the 8 times the machine has been serviced due to coins getting into the motor. I have a problem with rust around the dispenser. I also feel that the clothes get very tangled when washing. The machine is just 5 years old. This time when I called for repair with A&E appliance repair, they told me that it was going to be $450.00 to repair. Now, I am not going to repair it, especially after having all the problems I have had with it. I will never purchase another Whirlpool product or any of their other products that they make. I did call Whirlpool just to let them know my problem and to let them know that there have been hundreds of complaints with the same washer that I have. It’s too bad that Whirlpool has no respect, passion or pride in what they make. I am going to purchase a new washer and it will not be anything related to Whirlpool.

This Whirlpool washing machine is incredibly annoying and slow in everything it does. First off when you press the START button it takes 2-3 minutes before it decides to do anything, like maybe add water (except click, click and more click). If you have pressed the start button and you want to stop it to add something... again you have to wait almost 2-3 minutes before the lock is released and you can open the door. I am at 2 hrs and 15 minutes as I write this on the LIGHT WASH cycle with extra rinse and its still going. I have never seen anything like it. Cant imagine how long a HEAVY CYCLE takes. Cannot even try to measure the time. I put the load in and go to work and hope its complete when Im done 8 hrs later.We had a Maytag for 15 years with no issues (other than a drain hose cracked and had to be replaced) and it was time for a new one with a move to a new place. The sales associate convinced us this was the best machine at the time... Well what a mistake that was. There are no complaints about the actual washing. Everything comes out clean but I suppose taking that long I cant imagine why it wouldnt. I certainly cant recommend a Whirlpool washer to a friend, because I dread the thought of doing laundry at this point.

I bought a front loading Whirlpool washer a few years ago after having my old top loading Kenmore for 25 years. It seemed okay, but I did always have to leave the front door open and it always smelled musty, which was of some concern. My clothes never smell totally fresh. The biggest current problem is that several months ago it started with a failure code, alternately would stop without draining, wouldnt fill, or wouldnt drain, and ultimately ended up flooding my basement. So we called for service and they replaced a sensor and said these machines seem to have a lot of service issues with sensors blowing and motors dying. So I paid them that time. Now its a month or two later, failure code again, calling for service one more time. But if it costs too much I will join the legions of dissatisfied Whirlpool customers and will switch to an upright competitors brand.

I bought a Whirlpool 3.4 Cu Ft. Top Load Washer, Model: WTW4800XQ on Sunday. Today is Tuesday morning, but the machine broke last night. It lasted for about 5 loads and they were not big loads, unbalanced, and yes I had the right amount of soap. Whirlpool is saying that I washed something that was not machine washable. However, that is simply not true. I washed the bathroom rugs (which have been washed many times before) and they are saying the pump is clogged. If I had a washing machine 48 hours ago, do I really have to pay a service repairman to fix it? I will never buy any Whirlpool product again.

Piece of junk that tears up clothes but doesnt clean. Company has ZERO care for their customers. I will never buy Whirlpool again. We called and called and called. Washer took two hours for a normal load. Crust and odors still there. Dryer was fine.

Cabrio washer bought 5 or 6 years ago. Started a whining noise when spinning, so loud we close the washroom door to hear the TV. Called service, they immediately knew that the main bearing was going out & quoted the two parts needed to fix THAT COSTS MORE THAN THE MACHINE DID NEW! Labor was not included. Was also told that it will eventually start leaking. Piece of junk. What happened to simple washers that did a good job washing in half the time that lasted 15 to 20 years???

I purchased this monster in 2012 and after six years of enduring not enough water to actually wash the clothes for years, now the bearings have gone out making it sound like a jet engine is in my family room when it spins. After researching the bearing issue, I find it will cost $250 to $300 to have them replaced. Its also a common problem in this model even when the washer isnt at all worn out and old. That combined with the fact that my clothes dont smell clean and some blankets come out not even wet at all, Im done. I wont ever buy a water efficient washer again. Churning the dirty underwear around with a few cups of water isnt acceptable. NOTE: The bearings left months after the extended warranty expired. Just like clockwork. I purchased a much cheaper - center agitator - washer with a deep water option available. It was half the price of this top of the line Whirlpool Cabrio Washer.

New whirlpool washing machine 2016 - This washer is supposed to be smart, but it NEVER fills up with water! I always have to fill a bucket with water and throw it in the washing machine. My clothes do not come out smelling fresh and its not the detergent to blame, its the washer! Im so disappointed with this product. Whirlpool should stop making products.

Bought at Lowes. Washer was horribly out of balance on first use. Called warranty # to get service. Was made appointment by Whirlpool for next day. Too good to be true I thought and I was right. A week later, repair company called to make their own appt, chuckled and said Whirlpool does NOT make appointments for them. They came out to see washer and at the time of appointment, the guy said sometimes they come from the factory not hooked up right inside and after he went back to a lady in the office, Jonnys Appl Repair, Bozeman, MT said they would not fix it because washer was not sitting on a concrete floor. They are idiots. Finally, washer completely broke 7 months later. There was no service that would honor ANY appointment Whirlpool made. Went through 6 repair companies trying to get a close appointment date. Hopefully next week will be the magic repair. GO WITH SEARS. Repair is directly through them and they show up when they say they will. Ive never had a new product not working right when purchased at Sears.

I have posted on here in the past about the problems with the Cabrio Washer from Whirlpool. Our third top load lid was just ordered since 2011. There is a design flaw where the plastic frame around the lid cracks and causes the lid to hump up. While shopping at a local appliance store recently, I saw a new Cabrio washer and the lid and hinge system has be re-designed. I wonder why?????

I was very excited about the performance of the washer as far as reduced water usage and reduced electric usage. After about 6 months though, I couldnt figure out why a lot of clothes, sheets and drapes came out with streaks on them. Very expensive to replace! Of course, the business I bought them from tried to get me to buy all types of fixes that had nothing to do with the problem and therefore couldnt answer me why this was happening. I am not crazy about a lengthy lawsuit. I am crazy about hoping the washer dies so I can go back to a less fancy washer that did the job better than this expensive monster!

We have had this washer for a little over three years. We are a family of 2 so it gets only light use. The agitator stopped working and the repair was going to be $370! The repair person suggested we contact the manufacturer but they refused to even pay a portion of the repair. Goodbye Whirlpool! And yes, it left white streaks on our clothes as well.

Bought the washer on November 2013. Today 1 August 2016 the driving motor broke. The cost of the motor is 650.00$. I will not buy another Whirlpool product ever.

Purchased a Whirlpool Cabrio WTW7340XW2 washer approx 2 years ago. The machine runs so loud on the spin cycle you cant have a phone conversation or hear the TV over it and is leaking grease from the bottom. My mistake to not purchase the extended warranty but you would think a machine would last more than 2 years. I contacted Whirlpool online and by mail and they do not stand behind their product. I did contact a local repair shop and by our phone conversation was told it would be approx 300-350 to fix it and Im not putting that kind of money into a repair. Just want to let consumers know this machine is junk and spend your money on quality appliances, not Whirljunkpool.

We bought our Whirlpool Cabrio Platinum top-loading high efficiency machine Model #WTW8000BWG in Feb. 2015. It cleans well, and is easy to select water temp, spin speed, etc. It's simple to load, but because I am short, I have difficulty reaching stuff at the bottom of the tub. A stool is needed. LOL. In the 5 years that I have owned it, I have not needed any kind of service to be done on it. Very reliable. I have had Whirlpool washers and dryers before and my success with them is why I purchased the set I have now. And so far, so good. Highly recommend.

This company has terrible, deceitful, and pass the buck practices. I purchased a Bravos MCT top loading Maytag washer from Home Depot. Maytag is now owned by or has been acquired by Whirlpool. First I was a little disappointed to learn that because I had previously purchased two Whirlpool made washers and got no more than six years of service out of both them. But from the day this washer was delivered it did not perform as it should. I called and texted with the hours provided for rejection of the washer and was told by a customer service representative that it would be replaced. The main problem was the spin cycle. With only a few clothes in it, it jumped all around and moved so much that it was sitting in the middle of the washroom. Thinking that occurrence was a one time thing, I stopped it; cancelled the cycle; and reset it. It finished the load. This occurrence was reported and simply fell on deaf ears. I was lied to and told a replacement would be made; it was not. I have sent numerous emails and have made several calls for more than a year now and I still have the same defective washer in my home. Each time I emailed, I received a different message from the customer service person. This company wants me to pay for a service call or buy an additional warranty for a defective machine they produced and refuse to honor their replacement policy— which they now say is the responsibility of Home Depot. Luckily I have kept every email and document I was provided. I am being forced to file a claim against this company to get their attention and to remedy this situation. The expense of the claim will be greater the cost of purchasing another machine, but it is this kind of behavior, on the part of A corporate giant, that is makes life tough for everyday people like me. Stay away from the Whirlpool name for washers—even a prior good name brand like Maytag.

We wanted the ease of use and longevity of a top loader WITHOUT a full touch screen. Whirlpool has such units in a choice of price levels to accommodate most everybody. The agitator free design and automatic water level feature is amazing. Clothes are nice and clean and uses about the same amount of water as flushing a toilet.

We purchased the Whirlpool Cabrio washer a few months ago. When we wash the white cloths using the (white) setting and add bleach and the HE detergent, the washer does not clean the white cloths very good at all. Sometimes the white cloths come out looking worse than they did before they were put in the washer. We called the people at Whirlpool and they said there is nothing they can do as long as all the functions on the washer work the way they’re suppose to. I thought the function of the washer is to clean the clothes but, they say no, as long as everything on the washer is working. That is what their warranty covers.

So I have had the washer for a few years - bought it new or at least I thought. First came a clunking noise - fixed that. Next came the F1 code and installed a new pump $90 plus dollars. After installation, Im still getting F1 code and am now being told it is the ERC control board or water inlet valve either way a guessing game which in the end will have cost me over $400 to fix myself. I wish companies like this would stand behind their merchandise.

The machine never allows enough water to clean the clothes and I do not have the option to add more water or to spin the clothes again. The maker of this machine must think that people do not have the ability to know how to wash clothes or think for themselves. I need a washer that I can tell to add more water or just spin these clothes again. Very disappointed. I need an older model that I can control.

We owned a Whirlpool Duet washer that went out in late December 2011. We bought another Whirlpool Duet washer on January 8, 2012. On July 31, 2012, it stopped working with the error message F24. In WV, Whirlpool contracts their insurance/warranty through ACE Appliance. We scheduled with ACE the next day. They came out on August 6, 2012. The repairman told me it would be 7-10 days for the part. The part was on back-order, so in reality it took 17 days before they returned. It was repaired on August 23, 2012. Today, September 17, 2012, the washer stopped working again with the same error: F24. Whirlpool will do nothing to replace the washer, even though it is less than a year old and we paid $900 for the washer. This is the second Whirlpool we have owned that has crashed. I have two small children (4 and 2) and I am due with number 3 in 3 weeks. While the washer was broken, I spent nearly $80 at the laundromat for washing only - I carried baskets of wet laundry home to dry. And now I get to repeat the same exact struggle less than a month after it was fixed. When asked, the customer service rep told me that no matter how many times it broke, all they would do is send a repairman. They never ever replace appliances regardless of the problem. I am unbelievably frustrated and I want to tell everyone that I possibly can to stay away from Whirlpool appliances! Do not buy them new! Their manufacturers warranty is a joke!

I purchased this washer over 8 years ago and we have been using it 3 to 4 times a week/ 52 weeks a year since. It has performed flawlessly up until about a year ago when it kept given me uL error. Everytime I wash the basket always spins wobbly and unbalanced it seems. I checked the Internet and it turns out others have had the same problem. The solution was to replaced the 4 springs supporting basket and that fixed the problem. Been working ever since.

Whirlpool Cabrio Platinum WTW8800 model - In the words of the service technician who came out finally to service the machine. This machine is a piece of crap that should be recalled from the market. It is a low level-water unit that has no agitator ability in it and does not provide enough water to even slightly clean clothes. Everything must be sorted into the smallest loads possible and even then the clothes dont clean because they beehive into a ball and do not agitate. Technician says the machine cannot be fixed and simply recommends it be trashed (it is 1 1/2 years old). Technician recommends going back to front loaders where at least the clothes agitate. Called Whirlpool for help and was told all system are down...duhhhh. Call back in an hour and Good Luck.

Pathetic pathetic service!!! Unsatisfactory service!!! First of all, I would like to tell everyone who ever reads this, that please please please never ever use any Whirlpool products, as their service sucks, their response sucks too, and zero co-operation from their people, which will make you regret to have used their products in future. Please note I registered a complaint on the whirlpool no. **.The complaint was that the washing machine used by us had issues, the power button/ on & off button had come out, and this was clearly stated while registering the complaint. I get a call from Mr. ** (Representative of shree enterprises bibwewadi, pune) and the power button issue was well informed to him as well over the phone by me. He arrived to our place without any new material, he sees the machine and interchanges the buttons, i.e. the broken power button is replaced by other button from my machine which was less used compared to the power button. I had to pay a sum of rs. 400/- for the pathetic service I received from your end.I expect a response from your side within next 4 hours, or I might have to escalate this issue!!! (Please note Whirlpool team that I had submitted the same on your website yesterday, yet I have not received any response from your side). (Whirlpool rating- 0 out of 100). Thanks. (And whoever reads this, please tell me where else can I post this review of mine so that I shall alert everyone that how bad whirlpool service is)...

This washer is 5 years old and the top is rusting out on the inner rim. I have city water that has been tested and found to be totally safe to use and drink. Neighbors using the same water and owning different brand washers have no rust problems. Does anyone else have the same problem with their Cabrio washer?

The Whirlpool washing machine I bought is a piece of crap! I only do laundry every 3 weeks/3 loads and the machine broke in 13 months. Now it has broken a fourth time/same part - I have had the machine for 5 years and they can not do anything about it. I will not be buying Whirlpool again - of any kind.

Whirlpool Cabrio Washer WTW7340XW sounds like a small jet during spin cycle. The Whirlpool Cabrio Washers have a very well known and well documented problem with the tub bearings failing. Many many disgruntled owners have posted their complaints online, and there are many videos showing the issue on youtube. This issue is so prevalent that the manufacturer has created a tub bearing failure repair kit for $350. The repair is so expensive and labor intensive that many of the certified Whirlpool repair shops no longer work on the Cabrio washer stating that a better washer can be purchased for the cost of this repair.That said, the manufacturers customer service group denies that the Cabrio tub bearing failures is a common problem and are quick to state that Whirlpool holds no liability for this problem. Ramping the complaint up to a customer service supervisor is met with the same canned response. Regardless of the thousands of complaints Whirlpool is claiming that it is normal wear and tear for the tub bearings to fail. The manufacturer should recall the units for this manufacturing defect in the Cabrio design.

After having an expensive front loader (ugh) we purchased the Whirlpool Cabrio top loader (wow)! Best washer ever owned, wouldn’t trade it for any on the market! It has been as great and problem free as the front loader was terrible with cleaning and smell.

I purchased the Whirlpool washer with the expectation of having at least clean clothes. In fairness, I do wash some pet items but they are done separately. My clothes at time come out dry in spots because theyve not been touched with water. Forget the balancing issue. What I will have to do is wash, rinse, and repeat. This will be my life until I can get a new washer. Never again Whirlpool.

I purchased a Whirlpool Dishwasher, model DU1010XTXB1, 13 months ago and now it wont drain nor come on. Interestingly enough, the company claims no fault and wants to charge $129 just to diagnose it. This product has never worked properly, happens to have recalls for the exact same model number, yet wont acknowledge or expand its serial # coverage despite that it is the same exact problems! Do not buy from Whirlpool!

Whirpool WFW9550WW-00 Front Load Washer - Washer was purchased 08/09/12. No problems until 07/12/15 when washer stopped working mid-cycle. Motor control board needs to be replaced, actuator needs to be replaced. $500+ Our local appliance store suggested we call the Whirlpool customer relations number and ask for the parts to be sent free of charge. We would pay labor. They gave us the model number, serial number, the diagnostic info. Long story short, customer service told me she didnt know why I was told to contact them. They can not predict the life of a machine. Less than 3 years for this machine. 22 years for my old Kenmore. Our old Kenmore never had a problem, but we thought that we should replace it in 2012 in case something happened with old machine. WISH WE KEPT THE 22 YEAR OLD KENMORE.

After almost 5 years of satisfactory performance, our $1200 Whirlpool Duet washing machine WFW9400SU1 requires repairs costing over $1100. Similar to another complaint listed, some parts rusted out, leading to extensive damage during use, which we realized only after the spin cycle became incredibly loud. Now the entire gut of the machine (bearing, drum, arm, casing, etc.) needs to be replaced - $900 parts and $200 labor. I trust my repairman (who said theyd seen this type of problem before with Whirlpool) especially because he recommended buying a new machine instead. I called Whirlpool, and they said they could do nothing for me which made me very angry. This is a mechanical problem that could have been avoided by using proper materials. Whatever happened to the washing machines that would last 15-20 years?

I purchased the Whirlpool Duet Steam Washer and Dryer in the spring of 2010. Washer bearings just broke. I was told that the bearings in these machines are not strong enough to support the spin cycles. It is very disappointing to think that a company like Whirlpool would have their customers pay $1000 for a machine they know is not going to last. I agree with Julie. Maybe a class action lawsuit needs to be filed. Is there a lemon law for washing machines?

Whirlpool washer is junk. Expired I. Less than 4 years. Cost to repair is more than new washer. DO NOT PURCHASE WHIRLPOOL PRODUCTS. Agitator motor burned up without notice. No troubleshooter problem. 2 repairmen suggested I buy new washer.

Weve had this washing machine only a few years, and our household of 2 probably averages 1 load of laundry per week. Weve always had the same problem everyone has with the detergent stains on clothing and having to rewash loads, and the only remedy weve found was using the oversized loads setting and rewashing a load. The last straw was 6 months ago. It quit going through a complete cycle and would not spin out without resetting it. Then it quit spinning out at all. Service Guard, a 3rd party warranty company, diagnosed a faulty motor and ordered a replacement. After a long delay Whirlpool advised it was back-ordered for 3 months. A week ago Whirlpool advised them it was now back-ordered until 5-27. They did not know whether wed ever obtain a replacement motor. After taking clothes to our sons house for a couple months to wash, we purchased another used machine to use until ours is repaired. It is beginning to appear that machine may be our permanent machine. This is a pretty sad testimonial about whirlpool. We have always used Whirlpool appliances but appears we may have to switch brands. And it certainly does appear these low water machines are garbage. Very disappointed in Whirlpool.

We purchased this Whirlpool pair after our upright machine was unable to be repaired... because of parts coming from China and being hard, if not, impossible to get. We have had this pair for about 2 years now (Lowe’s). It still doesnt clean the clothes and it continually goes off balance when doing sheets, comforters etc. Myself I feel since they have taken the middle agitator out of the machine - it no longer performs the way a washer should and that its main function is to get the clothes clean! I did write a letter to Whirlpool about it and they pretty much told me, “Well too bad.” So much for buying American made products... at least the upright did last 6 years!

I like the newer technology that is built into the washer. My only complaint is that the wash time is automatically set depending on your load choice. For instance, a delicate load is set to wash for 45 minutes. I dont feel that amount of time is required.

I purchased a Whirlpool top load washer that has been ruining my wasted items. My terry cloth towels all have pulls in them, knit polo shirts have pulls and holes, sheets and other items of clothing get caught and stuck under the agitator which then take a great deal of muscle power and struggle to release them. I have had the agitator replaced 3 times to no avail! Whirlpool is not willing to admit that I have a defective machine and will be sending another service repairman to try and fix the problem - this time, no charge to me after many tries and frustration. Customer service is not good unless you are lucky enough to get a supervisor who is willing to listen. We shall see what this next service call brings. I do not have high hopes and will keep you informed.

We purchased Model WTW81920758200YW0 on September 8, 2012. Its performance has been unsatisfactory, not cleaning the clothes as advertised. Not long after the warranty expired the main bearing failed, bringing a local service technician and we were left with a bill of over $300.00. Yesterday, the machine stopped in mid-cycle. The display went blank and the lid lock would not release. I called a local service company for a visit and the soonest a repairman could show up was next week.A call to a service we had used for the bearing surmised that without knowing the cause of the failure they could only guess that a circuit board was at fault. That visit would be over $300.00 with labor and materials. That was the last straw. We broke the lid lock to retrieve the contents and took a ride to buy another brand of washer. We went back to the appliance store where we purchased this machine to buy a Samsung front loader. The salesman apologized for selling the Cabrio in the first place. Good money after a bad product.

I purchased the Whirlpool washer in February 2019 and delivery was in March. As stated in my previous reviews for the manufacturer, and subsequent repair calls, three; from the first time using the washer, it didnt fill properly for the amount of the clothes in it. A piece of paper towel never got wet through the whole wash cycle. I had to resort to raising & lowering the lid numerous times to get to the correct water level; adding water with a container or just pressing down on the switch under the top cover; 4-5 count. Needless to say very time consuming. As for hot water for doing white clothes, forget about it! It seem to me its the same problems with this whirlpool washer thats been happening with most of the other reviewers/purchasers. Did Whirlpool ever think about taken back one of these problem washers and checking it out for themselves? Maybe installing a clear plastic lid to monitor water levels at different wash cycles? Hot water temps when called for? Are these negative reviews ever seen by Whirlpool? Or in the trade is it called.... JOB SECURITY? Any more detail required? Cabo

Back in the day GE appliances were made to last and last - the only one I have found close is Whirlpool. They have style, dependability and long lasting products. My washer machine has a ton of features and I didnt pay more for any of them.

What happened to the Whirlpool Corporation that we grew up with? I purchased a Cabrio Washer on 8-29-11. Here it is, 4-24-13 and the transmission is shot. Two loads of clothes were ruined and sensors went bad. All in all, over $500 to repair it. I called the customer service line, what a joke - bad product and worse customer service. Not even and Im sorry. Well it is out from under warranty and when I buy something, I research it first, she said. Wow! Thanks Reena for all your care and concern. I dont know if Ill ever buy Whirlpool again.

I bought this machine in September of 2014. Six months later I HATE IT!! It does NOT get the clothes clean and dont even try to bleach white towels or socks, it doesnt pump the correct amount of hot water and things come out just as dirty as when they went in. It tangles everything together and frequently stops working because it unbalances the load with its lack of water. Ive always been proud of how my familys laundry looked and now Im just embarrassed. Im considering donating this to a human society for dog towels. Stay away from this washer, its horrible. Im going to the laundromat and shopping for a new machine ASAP!

I purchase newly Whirlpool washing machine but it was not working from the first day of my purchase. So many service Engineer came but nobody can solve the problem, so I suggest to all please don’t buy washing machine from Whirlpool. I am very disappointed from this company.

I purchased a Whirlpool front loader as well as an extended warranty. The machine worked well for about a year and a half until i noticed rust patches beginning to form on the front of the machine. We contacted the retailer that we purchased it from and they suggested that we call the people that we had bought the warranty from. Unfortunately, the warranty does not cover rust, so we have to wait for it to rust out and just buy another one. It is only 2 and a half years old and is totally rusted across the front of the machine! It is extremely unsightly. This is the second Whirlpool washer that we have bought and the second one to rust out on us. I would never buy another Whirlpool appliance, and extended warranties are not worth the paper they are written on, let alone the amount that you pay for them!

Purchased the Whirlpool Cabrio washer January 2010. Purchased the extended 2 year warranty from Lowes. After about a year I noticed around the bleach dispenser it was starting to rust. Over some time it worsened and grew bigger around all sides. I was unhappy about it, but thought it was just cosmetic and didnt pursue the issue. Now it must be on the inside and has started putting yellow spots on all of our clothes. It was only a towel or two at first and now it is on everything. I called Whirlpool and Lowes customer service center and they are just sorry and will not do anything. Lowes warranty does not cover any rust whatsoever although I cant find that stated on the warranty papers. I will never buy another Whirlpool product, ever. $600 for a washer and $70 for an extended plan to last on 3 years. I know people who have washers for 10 or 15 years. Im so disappointed.

In October 2009, we purchased a Whirlpool Cabrio topload washing machine for almost $900, because my wifes sister had a 1-year-old one and had been pleased. The Cabrio replaced a 3 1/2-year-old Maytag that died with a seized-up transmission. Maytag is also a Whirlpool product for those of you who do not know. We had issues at first with it going off balance but dealt with it. It was also taking 40+ minutes to do even a small load of laundry, but again, we dealt with it. Fast forward about 3 years, and we notice the machine is making really loud sounds during the spin cycle. I checked for any obvious issues but found none. The noise kept getting louder with each use. Finally, I called a repairman to check it out. His diagnosis was quick. The bearings were going bad in the machine, and he said it would eventually fail. He quoted me a price of between $400-$500 to repair because the job is very labor-intensive. I declined the repair but still had to pay him a trip charge. Then I checked with my wifes sister about hers, and she said hers had been making a very loud sound for several months but they were just ignoring it. I told her about the diagnosis of mine and advised her to tilt the machine back to look under it. Sure enough, there were oil stains under her machine, just like mine, indicating the bearings were failing. So we have 2 Cabrio machines, one 3 years old and the other 4 years old with the exact same problem. I called Whirlpool since I had registered the machine when I purchased it. They basically told me to go fly a kite since I had not purchased the extended warranty. They said I could attempt to repair it myself to save money, but they advised to have their repairman do the work. Well, no kidding. What a joke. They expect you to buy a $900 machine and have to replace it every 3 years. I am done with Whirlpool products. FYI, Kenmore products are also made by Whirlpool, so Sears is not an option. My wifes sister and we bought new GE washing machines, and both of us purchased the extended warranty this time. For $129 (5 years), its cheap, peace of mind. Whirlpool is crap. I would suggest never buying any of their products. I know we never will. Once they have your money, they dont care.

I bought a Whirlpool Cabrio Platinum washer 2 years ago and it is by far the worst washer I have ever owned. Its a water saving device with extremely long cycles. The clothes dont get wet enough, dont come out clean and they do not smell fresh. I have to put them through 3 rinse cycles and often times have to re-wash my clothing. The cycles are very long, using more electricity, and it takes me 3 times as long to get my weekly laundry done. My clothing comes out more wrinkled and twisted causing longer time ironing. My old agitator style washer did a superior job compared to this piece of junk. I dont like the automatic locking lid, nor do I like the machine choosing the spin cycle for me. There isnt even a soak cycle. If I want to soak my things I have to do it in the sink and then drag them to the washer to rinse and spin them.I spend a fortune on laundry additives in order to get my clothing clean and then they arent as clean as with my old washer. I now dread doing laundry and every time I look at the washer I feel like taking it to the dump! There isnt anything I like about this machine and I wouldnt recommend it to anyone. It is a piece of crap. This is 2016 and they havent learned how to make a good working washing machine. When I move, I will be celebrating leaving it here! I will never, ever buy a product made by them again.

This machine was my dream machine for about two years. Then the noise started during the spin cycle. It gradually got louder and louder, until it got so loud that it sounded like a jet engine taking off. You could not be near the wash room and hear each other talk. Then it began to aggravate me with the UL flashing. I know how to load a washing machine. It was just a defect. Then it started making a grinding sound to add to the roaring spin noise. We were told that it would take over $500.00 to fix, so we just sat back and waited for it to die. Well, the other day it began to leak some water out of the bottom of the machine. Now today we are paying our last respects to a piece of junk that Whirlpool calls a washing machine! It is less than 5 years old. This was a $900.00 washer. There should be a recall. We should ban together and demand a recall! Now I will be forced to go buy a new washer. I can tell you which name brand I will not buy, Whirlpool!

My Cabrio washing machine is a hunk of scrap metal after five years of lite use. Replaced the electronics first, then a year or so later replaced the motor. Now its leaking from the bottom. Repair man said it is not fixable. I did not buy a warranty because it was too expensive compared to the value of the washing machine. My recommendation to anyone buying a Whirlpool appliance is to buy the cheapest thing on the market, so that you can throw it away when it breaks because they are made to break so that they can sell you extended warranties.

I dont know who is the bigger idiot. The designer of this washer or me for not reading the countless bad reviews. I bought a Whirlpool 4.3 CU FT TL WTW5000DW machine on 7/19/2015. It does not come close to cleaning clothes. It now takes me three times longer to do laundry because I have to check every piece of clothing for any stains. These are minor stains mind you but, they will not come out unless I use something like Spray and Wash. My time is valuable, maybe I should drag my clothes to the river and beat them on a rock. Very disappointed.

Bought this machine at Lowes as it was recommended by the salesperson. The machine broke down in 2 months due to a control module. Besides that, the clothes do not get clean! They come out with all the stains still on them. The water does not even get the clothes wet! And they smell. Called Whirlpool up and they sent out tech 2x and said there was nothing wrong. Went back to Lowes and they will not honor my claim to replace the unit. I now have to purchase a new machine since this one is useless. Never will I buy a Whirlpool again and dont you either!!!

WHIRLPOOL WTW5000DWO WASHING MACHINE TOP LOADING 2014 MODEL - I purchased this above model at Lowes of Hagerstown MD. The first problem I had with the washing machine was the spin cycle did not wring out the clothes. The second problem was the spin cycle caused the washer to start walking. The washer was leveled prior to washing the clothes also water was still running into the washer after it cycled off. I call Lowes the next day and told them my problems and they replaced the unit with the same model. The delivery came and I hooked up the washer and placed a few items in the washer and allowed it to cycle through. The washer did the same thing all over again. It did not spin the clothes out and the water continued to pour in the washer. And spun out of balance. I contacted Lowes and advised them I was having the same problem. I also told them my cousin had the same model and they were also having the same problem. Lowes offered to replace the unit with a different model so I selected Samsung washing machine and I have it scheduled for delivery tomorrow. Also I wanted to let you know that the price difference was 100 Dollars more for the Samsung and Lowes told me that I would have to pay the difference. I told them I have been inconvenienced twice and I will not pay the difference, they then call in the store manager and he override the difference. Lowes of Hagerstown will try their best to make it right, its sad that the mfg will not bring a product to the market that will do what it is advertised. The federal and state government should fine these companies and replace the defective models when reported. Do it right the first time and you wont have a repeat of the same problems. Also not use the consumer as a guinea pig to try out new products.

My top loading Whirlpool washer model WTW57ESVW1 failed after just over two years. When I called my service man, he turned it on and immediately told me it was not worth fixing as the transmission was bad and this model was known for this issue. I contacted Whirlpool Corp. and the person on the phone stated she could do nothing for me. I asked for a supervisor and was told she would give me a discount on parts, but I had to find out just what part it would be before she would tell me what percentage of a discount she could give me and the service call was my responsibility. Due to this treatment, I will not buy another Whirlpool nor will I recommend it to any of my friends. I will also post on Facebook my experience with Whirlpool.

Cabrio - In Dec 2013: Ran the Clean washer cycle and it would not cut off. I had to shut off manually. Called the company and they sent a technician, who said he fixed it and that everything was good. Fast forward to Feb 2015: Tried cleaning the washer again. When I left the house there were 10 minutes left in the cycle. When I arrived home 7 hrs later, the washer was still running and my hot water heater had cut off. I had to reset via the circuit breaker. This will be my last Whirlpool appliance for a long while.

We purchased our Whirlpool Front Loading HE Washing Machine a year and ten months ago from Future Shop, and now it has failed. After paying about $100 for a service call, we were told we need to order a motor control board that will cost an additional $397 plus tax, plus installation. Because it is off warranty, this means my $1030 washing machine that is less than two years old will cost me about $680 to repair! My parents old top loading washing machine still works after 30 years. And now I notice that so many other people have had the exact same problem. Why hasnt Whirlpool fixed this issue? This is criminal! What on earth is going on here? I was under the impression that Whirlpool was a top-notch brand.

After 7 attempts to fix my 6-year-old Whirlpool Front Load Washer (original price $991.00) I had to trash it. Then I stupidly bought another Whirlpool Front Loader (WFW75HEFW) Feb 2017. It has not worked properly since day 1. The clothes come out dripping wet. At first I thought I was doing something wrong. I tried every cycle, limited amount of clothing and ran additional spin cycles to no avail. Finally I gave up and called for service.Whirlpool is very much aware that a number of their machines came off the line with defective spin bearings but they wont admit to it. Instead I am expected to have it repaired! It involves the entire inside of the machine being rebuilt. Its a 2 man job that will take 3-4 hours.This is totally unacceptable and it is obvious Whirlpool does not make a quality product nor do they value customer satisfaction. DO NOT UNDER ANY CIRCUMSTANCES PURCHASE A WHIRLPOOL WASHER. They are difficult to work with and I for one will never purchase or recommend any of their products. I purchased this washer from Home Depot and now my only hope is that they will honor my intention of purchasing a non-defective product. If not, I guess Im in for another miserable experience with a Whirlpool product.

I purchased a Duet several years ago and did not have a clue as to the problems everyone was having. Over the course of ownership I called the city to determine if we had a sewer leak. I had a plumber inspect our pipes. I felt really stupid that it took me this long to figure out it was the washer. I knew it smelled like mildew and have been using vinegar, afresh, Clorox until I am blue in the face. I didnt figure out that the sewers smell was also the same as the washers until I got on line and read about these machines. Finally, I lifted up the gasket around the door and it was completely black with mold. No amount of afresh was going to fix this problem. Do not purchase these front loaders. Feel like they should have been recalled and I really dont understand why they are still in circulation. I have also been having health/breathing issues and I cant help but think the mold is causing my illness.

Does not get your clothes clean. They come out of washer smelling due to lack of water. Darks have Detergent Residue on them. My t-shirts have holes in them. Bought this machine in 2010. Just purchased a Whirlpool top load with a Agitator and I am very pleased with the results. We never had any problems with Whirlpool products but this Cabrio should be taken off the market, faulty advertising. Talked to a Whirlpool rep and she told me to bunch up clothes and place around outside edges of machine for best results but did not see any difference. Do not buy this washer. You will be wasting your money and you will be buying a old traditional washer, with an Agitator is your best bet so you can control the amount of water you use. I hope this helps one that is thinking of buying the new technology top load Cabrio with HE.

I have bought what I thought my dream washer and would never need to buy another one. I told people about it and could have sold many of them. That was in my first year. Now I am into our second year with them and it quits. It cost right at 500.00 and when I called Sears, the company I bought it from, they charged me a service call and says it will be $585.00 to fix. WHAT? This is a lemon. If I were to buy a car and have this sort of problem they would warranty it. Why not appliances? This is an outrage. This should be illegal to sell.

I have had this washer for about 7 years. I have not had any problems with it. I wish that it is stingy with rinse water. I see suds on the items before the rinse cycle and it doesnt seem to use enough water for a good rinse. Therefore I use the extra cycle.

I purchased a Whirlpool duet front load washer on 21 Apr 10 and it has experienced a major failure. It needs a new rear tub and basket, and the parts alone costs $700. The machine is barely four months out of warranty. After a lengthy conversation with a Whirlpool customer service representative, I was told that without an extended warranty, they were very sorry and there was nothing that they could do for me.

I purchased a Whirlpool cabrio mod. wtw5840bwo washing machine in Oct. of 2014. As of June 2015 I am ready to kick it to the curb. The washer works to it design and hasnt broke down but it doesnt clean our clothes. We load the machine, add the right amount of clothes and recommended detergents and 1hr later after the wash cycle is completed, the clothes still stink with the smell of daily perspiration. I went back to using our old washer that has a worn out agitator. It does a better job.

I purchased this washer (Whirlpool Cabrio HE) 2 years ago against the advise of many people including my husband due to the cost, $850 for what is now no more than a large paper weight! It had never really done a good job at cleaning our clothes. About 6 months ago, it started not spinning enough to remove all the water from the load. I thought, no big deal, I will just use the extra spin cycle. It became the normal thing - wash, spin, extra spin. Well, then it became wash, spin, extra spin, extra spin. I noticed 3 months ago that it was not even agitating. It fills up, sounds like it is agitating and then drains. There was no movement from inside at all. All along I am getting from my husband. told you not to buy it! I gave in and called the repairman - $185 for a console, $26 for a sensor and $55 for a couple of drum clips and then the $35/hour for the repairs. I would rather spend a couple hundred dollars and buy a washer with an agitator that really works. I would never recommend this washer to anyone!

Whirlpool Cabrio Platinum WTW8500BWO - It doesnt wash anything very well. I hate it. Dont want it. Wish I didnt buy it. I do all kinds and sizes of loads. My clothes come out dirty - I have to wash my clothes 2 or 3 times.

Whirlpool cabrio wtw7800xwo - During the 12th month of the use of this washer, the lid broke. I called Whirlpool to schedule a repair on it. I got someone here to repair it, and it was 7 days over the 1 year warranty. I don’t think this is fair when they sent the repair guy out too late when I scheduled this right before the 1 year was up. I came about looking this up online, and I find I’m not the only one with a 1 year lid. My next washer will be a 1980s built to last. This was the worst $1,100 I ever spent. I had to choose 1 star. Wish it had a choice of - ★★★★★.

I have a Whirlpool Cabrio WTW5640XW and I was able to get the belt back onto the pulley, about a month back and it ran, loudly, but it ran. Last week the belt popped off again and now the pulleys are screwed, so I probably won’t buy another motor (for the sake of the pulley). Ill get a front loaded Kenmore or something as I was never completely happy with how this thing washed and (didnt dry) our clothes.

Apparently, Whirlpool selling all their rejected faulty washing machine in the market. The trick they are playing is the machine being sold with one year parts-labor warranty; They wont replace these machines with a new one because they know that these machine will never work, consumer will buy the faulty machine, obviously it wont work so consumer will call for service. The service guy will say that “oh! Machine needs a part and then the customer service will say “the part is being ordered”, “wait”, then the service guy will come with the part and after wasting some time he will say “Oh! The machine needs another part, and again customer service will tell the consumer that “you keep calling us”. One year will be gone! Bottom line – faulty machine is sold, Whirlpool made profit, buyer is robbed. I am one unfortunate customer who purchased Whirlpool Washing Machine which never worked as it is a faulty machine which should not go to the market at all; Whirlpool made money on my hard-earned dollars and I been robbed.

I have had this front loader for 5 or 6 years. My clothes absolutely stick, I cant stand the smell of them. I have used Affresh, the recommended cleaner 3 days in a row, multiple cycles, no improvement. I did the vinegar treatment, leave the door open etc. What is upsetting is I have read Whirlpool has been aware of the mold and mildew problems of front loaders yet continue to manufacture them. The gasket in the front enclosure pockets at least a cup of water and other gunk from the wash. A waste of money!!!

8 cu. ft. Cabrio® High-Efficiency Top Load Washer with Steam - I bought a new washer. It did a poor job rinsing and spinning dry. Whirlpool customer threatened me that a service charge may be charge if the repairman came out and found nothing wrong. After calling three times I ordered a repairman out. The repairman explained that only way to prevent soap residue on your clean clothes is to use the bulky and deep water options. Also dont use high spin or when it spins your clothes dry, it leaves them in a tangled mess that requires ironing to remove the wrinkles. This washer is not ready for the market and must be removed until they can perfect it. It cost me $200 to return and exchange this model for the Front Load Duet, which works excellent. Whirlpool should be ashamed to have ever put this machine on the market.

We bought a Whirlpool model WFW5620HW front-load washer at Lowes. The unit shook so violently during part of the spin cycle that the Whirlpool-authorized service company technician said not to use it while parts were ordered. It seems the balance ring was not functioning. Parts ordered were shocks and tub assembly. The technician suggested trying to get a whole new unit, as the repair is so intensive he had only done one or two in his career.Whirlpool customer service said they would not replace the unit, and an escalated request had the same response. I think this is terrible customer service - when there is such intensive failure in the unit, they should provide a brand new machine. The work has not yet been done - we are without use of a washer for an unknown period of time, since the order of a tub assembly is so uncommon that they do not have a time estimate. Needless to say, we will never buy Whirlpool again, and suggest you do the same.