Bought this set for its basic functions. We dont need a lot of bells and whistles. The washer is rated as a water saver but it seems to use more water than our 10-year-old model. The only issue we had was with the electronics. Even though it has few features, it one day decided to not function at all. A call to support recommended just unplugging it for a few minutes so it could reset itself. For once this seemingly crazy idea worked and the unit has been normal ever since. I recommend buying from the outlet store as a scratch and dent. This saves lots of money and if the unit is not on display, who cares about the minor dent.

I am so disappointed with this washer. I totally dread doing laundry. The following are the complaints: Every load comes out totally twisted and wrinkled!! The soap/fabric dispenser holds water after each load (I have to take paper towels and get the dispenser empty!!!). There is not enough water to properly clean the clothes. I have never noticed a reduction in my water bill and have had this piece of junk since 4-25-13. There is NO short cycle on this junk machine. There is an odor to my towels - like they are musty - after I dry them and use them. I use Tide HE detergent and clean the washer with Affresh (you shouldnt have to clean a washer). I should have taken the time to write a review much sooner, but decided today was the day after doing laundry. DO NOT BUY THIS WASHER.

Whirlpool cabrio mod. WTW7300XW1 - I purchased this washer Nov. 2013. It did not work right from the day of delivery. Our clothes come out dirtier than before washing. Machine smells awful. I spend more in machine cleaner than in laundry soap. I have always purchased Whirlpool. Very dissatisfied with this model.

We purchased a Whirlpool Cabrio washer 6 years ago. This washer has been such a terrible appliance, I would not recommend that anyone buy one. The top of the washer has broken 2 times. Whirlpool will do nothing about it. It is a manufacturers defect where the glass pops out of the top and then breaks the frame it is in. We had it replaced last year and the new one is now broken - same problem. It also does not get clothes clean and the clothes get ruined because they become all entangled in one another. We will never purchase a Whirlpool appliance again. I did have a 5 year service contract on these appliances but once out of warranty - you are on your own.

Purchased the 2015 Whirlpool Cabrio. Today 5-2018, the panel went completely out. When I called the store (Lowes) they asked if I purchased the warranty. I responded no, she went on to say, “Well since you choose not to purchase the warranty youre stuck”. Even if I paid for the warranty a washer should not break down in less than 3 years. My previous washer lasted 18 years with no problems. We purchased this washer because of the larger load. It was one of the most expensive washers. It’s a piece of junk and the manufacturer will not stand by their horrible product. Please DO NOT buy! I will be filing a formal complaint.

This Whirlpool washing machine is over 5 years old and very reliable, I use it several times a week and have had no problems with it. Next time I will purchase a larger capacity machine so I can wash comforters and spreads easier.

I bought my washer duet (model WFW94HEXL2) in Sept. 2011. Today is Jan. 2013 and it has been a year and four months since I got the washer. I decided not to buy an extended warranty. Its only my husband and I at the house so we take really good care of our appliances. The washer stopped working and is giving me a code F-6/E3/E1. Basically, I need to change the central control unit ($350), door latch ($120) and labor ($180), for a total of $656.13. Really? I paid $1,105.00 for the washer. Im really upset. I called Whirlpool and they said the item is out the warranty and there is nothing they can do. I am really upset.

Clothes come out of washer are soaking wet. Despite multiple repairs within the warranty period (1 year), the problem was not fixed. Each time a separate part was replaced. I would consider this as a manufacturer defective product. Despite multiple complaints to Whirlpool customer service, they would not replace the unit. Problem continues and now the warranty period is over and I am paying for fixing the same problem. I would not buy a WP washer again.

We purchased our Whirlpool Cabrio platinum washer about 3 years ago. I am completely frustrated with it. When it is on spin cycle, it sounds like a freight train going through my house. During the rest of the washing... it squeaks. And right now this is the 5th attempt to wash the same load of laundry. Because it keeps getting unlevel and it will not continue after I move the clothes around to get it level. So I have to start all over. There is not a spin cycle option that is available by itself. Every time I have to choose the rinse/drain/spin option. Obviously it is not under warranty anymore! Only a one year warranty... really pathetic! And when we called they offered us a little discount to buy another one. No thank you!!! Wont ever buy Whirlpool again.

Whirlpool washing machine has always been reliable for me. I have owned 2 and they lasted me many many years. Its easy to use, and cleans clothes perfectly. My family is also a fan of Whirlpool appliances.

I bought a Whirlpool built washing machine on Jan. 8, 14. It stopped working on Aug. 9, 14. It is now Sept. 2, 14 and I am still waiting for it to be repaired. I am age 75 and it is difficult to load and unload clothes to take them to the laundry. The repairman order a part Aug. 26. Pony Express has not deliver the part at this time.

We purchased it from Best Buy. It was a good thing we got the extended warranty. They completely rebuilt it two times. In the 6 years we have had the washer. The motherboard went out. The bearings went out. The only thing nice I can say is that it’s a top loader and doesn’t get smelly like the front loaders do.

Two days after the one year warranty ran out on our front load washer it started making a terrible noise. Of course the Whirlpool warranty was no longer in effect. The good news I was sold an extended warranty from Nebraska Furniture Mart. Called the Service Provider and was told they will only service the washer if it is not working. After several more calls they scheduled a service call in 10 days. We are a family of four, yes no washer is a problem. Finally the technician showed up and said the main bolt holding the drum assembly in place had broken off. He would have to order the bolt. It is now on backorder for 3 weeks. No washing machine for 4 people and now nearly a month is a pain. Not only did my calls to Whirlpool do nothing but the calls to the third party Warranty Company have been very frustrating. My call to the salesperson at NFM was very helpful, but didn’t help get our washer fixed. This is our second and last set of Whirlpool laundry pairs in less than four years.

I purchased a new high-efficiency front load Duet HT Whirlpool washing machine (WFW9200SQ02) in January of 2008 for nearly $1000. I dealt with the mold issues and permeating smell for all these years, but the machine failed catastrophically this month - after just over 3 years - on a $1000 machine! The rear bearing went out. The parts alone are nearly $500 and the labor is estimated to take 3-4 hours by a trained technician. We are talking about an $800 repair --more than a new machine would cost. The most disconcerting part is to see how often this is happening. It is commonplace. The bearings go out on these things, sometimes after only a year or two, sometimes after 3 or 4; but it is very rare to have any machine go longer than 6-7 years. Whirlpool wont do anything. The best chance is forcing a recall related to the class action lawsuits pending about the mold issues, but by that time, how many people will still have their machines?

We purchased our a model WTW7800XWO 7 years ago. Our lid kept falling down when loading and unloading. Very annoying. 3 years ago it failed to lock down which means the washer will not start. We learned to press down on the lid sides to get it to lock. Then it became loose where it connects to washer and we duct taped it to make it work. We put up for that for a year before having a repairman attach a new lid. 1 year later it did the same thing... And we put up with it hoping it wouldnt totally fail. Today it failed. Since the 1st repair cost 250.00 we decided that we will get a new washer rather than spend another 250.00. We will go with American made Speed Queen. We have had Whirlpool appliances since we were married 50 years ago.

Cabrio (h2low system) top load washer ..USA 120 volt - A true piece of crap... Bought 2010... Even when it does work, 5% of any load will NOT spin out... The damn thing will refill its tub with rinse water to redistribute load so as to get a spin out. SOMETIME month ago, thing just dies... nothing. Technician comes out for two hours its the shift sensor. Replace for 200+ bucks... done. Works for three weeks, dies, tech is back. 4 hrs... its a bad processor board. Ordered 140$ rebuild, comes in mail few days later. Tech is back, replaces board. We have smoke!! Looks like a bad motor part. I could go on... but why. Never ever buy one of these sorry pieces of dreck. Absolutely the worst. Poor quality even when it works. Horrible wash quality. Never again Cabrio. Remember it.

Bought an HE top loading washer 4/19/19. Oil leaking on floor from washer. Today, 2/12/20, while still under one year warranty, had transmission replaced. We have always purchased Whirlpool appliances. Not sure if we will in the future.

Purchased on Nov 2010 at Lowes. Washer machine sounds like an airplane on the wash and worst on the spin cycles. Bearings are gone!! Customer service was no help. Basically was told I was ** out of luck. Have service bulletin addressing this issue, yet they refused to help. $1300 learning experience about Whirlpool. Social media here we come. Goal: to keep at least 1 million customers away from their scrap!!

In 2008 bought cheaper Whirlpool washer, had to return it to Lowes. ELLL DUMOH (me) buys yet another Whirlpool Washer from Lowes; a Cabrio. The Cabrio ONLY worked 3 years, and started having problems with not emptying or just continuing to drain and beep. The Whirlpool Customer Service lady is pitiful. Yeah... I can SELL you another set of shock absorbers... that might help. I can SELL you a recirculating pump or a drain pump... Pitiful, sorry attitude. Goodbye Whirlpool.

Purchased this washer new 2015 for use in our cabin. Now 4 years later with very little use the motor has seized. Washer is useless. What happened to 20 years of almost daily use and still runs great. This washer is a very poor quality washer and has now failed. Please save your money and buy a different brand.

This washer was expensive, platinum line. Clothes never smelled fresh and clean like they should. There is not enough water to cover and clean. After 4 years it started smelling dank and unpleasant even after cleaning cycle is run. Now I discover it has been leaking for quite a while. It will be 6 years old in July. The top wont stay up. This happened months ago. The part alone is 250.00 according to several sites. I just prop it up. Very displeased with this poorly constructed, expensive rip off!

My $800 Whirlpool Cabrio top loader does not rinse the soap out of the clothes. Nor does it even get the clothes completely wet. After the final cycle I have soap scum in all the wrinkles of the clothes. Most dissatisfied purchase I’ve ever made. The one-star rating comes from the pretty blue digital displays. I’ll be purchasing another; this one goes to the dump where it belongs!

Purchased this washer 7 months ago. We are a family of 5 with A LOT OF LAUNDRY!!! I adequately researched a machine that could do large loads of laundry, WELL. I read at least 100 reviews and went forth. (Note to self that anyone giving this machine a decent rating, is a DIRTY, SMELLY, FILTHY LINEN WEARING FOOL who doesnt take much pride in their clothing cleanliness.) I proceeded onward and after paying A LOT OF MONEY for this 4.8 Whirlpool Cabrio Washer, I found out within the first two days of owning it, that IT IS GARBAGE! Regardless of the 4.8 drum size, you can only fill it less than 1/4 of the way with clothes, to even hope they will be touched by water. My clothes come out DETERGENT STAINED & DRY! Insanity... A washer that doesnt wet the clothes!!! We have had 4 repairmen come out within this time, because I am fed up! I have been physically shown and told now, by all 4 guys, that the washer will not fill more than 9 inches with water. They advised me to fill Home Depot buckets and throw them into the drum. THIS IS WHAT I DO, TO SATISFY THAT I AM WETTING MY LAUNDRY - PURE CRAZINESS! The repairmen told me to set all loads to bulky sheets + extra rinse + highest soil. This is a 1 hour, 26 minute initial setting. Note that my adding water messes up the computer readings and it will reset throughout the washing cycle multiple times. Even with all of this... the machine still doesnt wet the clothes!! The top and center of the load is BONE DRY! This machine will not wash sheets, blankets or comforters, either. Dont waste your time trying!!! Dont be fooled by the drum size. Your great grandmothers 1930s 1.6 cu ft washer washed more clothes in any given load. #1 My water bill is through the roof. #2 The washer constantly resets and runs on any single load for over 2.5 hours AND #3 MY LAUNDRY PILES HIGHER AND HIGHER, as you cannot put more than a smattering of clothes in the machine, at any given time! GARBAGE, GARBAGE and MORE GARBAGE!!! I would be better served to find a stream and a flat rock and start doing my laundry colonial day style! I am done... Finally had enough of this insanity! RETURNED THE MACHINE THIS MORNING!!!

On November 1, 2011, I purchased the Whirlpool Estate washer (model # ETW4400XQ) from Wholesale Appliance in Charleston, SC. The first time I used it I knew something wasnt right when both the regular and so-called gentle cycle agitated at an incredibly fast speed. It is damaging my clothes. I called the dealer and they sent out a service person. He said that was just the way it was and he couldnt do anything. So, I keep trying to use the gentle cycle, but it was the same thing. I would have to stand by the machine and stop it after a couple of minutes so it wouldnt ruin the clothes. The more I thought about it, I decided that the repairman wasnt right. I called Whirlpool customer service and they sent a different repair service. He also said that he couldnt do anything to make it slow down as it was programmed by a computer inside and he could not change it. I went to the dealer, Wholesale Appliances, and they said there was nothing they could do as far as giving me a refund or a discount on a better machine. The setting on the washer clearly says gentle cycle.” Well, the whole world knows that does not mean beat the clothes to death as fast as possible. Can you make any suggestions? Thanks.

When we bought our house the Matching set of Whirlpool Cabrio Platinums came with it as they were new. I decided to keep them and sell my LG Troms.Absolutely the worst mistake was keeping these Whirlpools. Who in their right mind would consider a washer with no agitator a washing machine? The clothes just sit and do nothing. They don’t get clean at all. Its a complete pile of useless junk and the person or persons who engineered it shouldn’t even be in charge of designing birdhouses.Whirlpool themselves should be ashamed to put out such a pile of garbage to the consumer. Our house came with all new Whirlpool appliances and we are going to replace them all and never give Whirlpool a look again. Whatever you do don’t fall for the shiny unit, slick salesmen. Because all youre going to get with Whirlpools washer is all talk and zero action. Thanks for the not so clean clothes Whirlpool. The local laundry mat thanks you when I need to actually clean my clothes.

The machine pass all the cycles but the clothes are only very wet and still dirty.

Whirlpool Washer W10740628A - So disappointed! I have made adjustments for a year trying to get clean clothes from this machine. Compared to my previous machine which wore out, I now use more water because only deep water wash provides enough water; I always choose double rinse because if the machine does not clean, I do not trust it to rinse effectively either. I use more Tide than previously per wash; I use more Clorox than previously per wash. Everything from tea towels to heavily soiled jeans show stains and soils after washing. Instructions say not to spread the item in the washer but allow it to stack on itself, so twisted and tangled wet clothes are the result. I try to soak and scrub all visible dirt before I start the machine now; additionally, I use a mop or plunger or my hands to thoroughly immerse the clothes in the washer, somewhat like my mother did in 1950s. What on earth is this about and what is the buyer supposed to do???

16 months after purchase, the machine starts displaying F71 codes, 6 weeks later F70. After calling Whirlpool customer service number on the User Manual, we were told that the washer was out of warranty and there was nothing that Whirlpool was going to do for us. I have a reasonable expectation that a brand new $800 washing machine will operate for many, many, trouble free years, but finding an electronic failure that has been estimated at $400 to repair, 16 months after purchase, is simply and obviously unacceptable. This is clearly a defect in design and/or manufacturing.

I have posted on here in the past about the problems with the Cabrio Washer from Whirlpool. Our third top load lid was just ordered since 2011. There is a design flaw where the plastic frame around the lid cracks and causes the lid to hump up. While shopping at a local appliance store recently, I saw a new Cabrio washer and the lid and hinge system has be re-designed. I wonder why?????

We bought a washer in Sept. 2014 and it was used for 4 months before we left and went south for the winter. When we came back in May, we started hearing a loud banging noise so we notified Whirlpool since we were still under warranty. They sent a repairman and he said he needed to take the washer in so he could repair it. They have sent the part out 3 times and they said it was chipped or cracked so another would need to be sent. This has been going on for 2 months that weve been without the washer and today we checked and supposedly another part should be coming. They tell us our warranty is only for parts and labor not replacement. Help would be appreciated. Thank you.

Im no longer buying Whirlpool products. They do not all up and are made like crap. My Cabrio washer being the most recent problem. Hinges broke on the lid and the drum spring broke. Out the door it goes! Im having my American made Speed Queen delivered tomorrow, the last Speed Queen I owned last over 30 years.

This machine was my dream machine for about two years. Then the noise started during the spin cycle. It gradually got louder and louder, until it got so loud that it sounded like a jet engine taking off. You could not be near the wash room and hear each other talk. Then it began to aggravate me with the UL flashing. I know how to load a washing machine. It was just a defect. Then it started making a grinding sound to add to the roaring spin noise. We were told that it would take over $500.00 to fix, so we just sat back and waited for it to die. Well, the other day it began to leak some water out of the bottom of the machine. Now today we are paying our last respects to a piece of junk that Whirlpool calls a washing machine! It is less than 5 years old. This was a $900.00 washer. There should be a recall. We should ban together and demand a recall! Now I will be forced to go buy a new washer. I can tell you which name brand I will not buy, Whirlpool!

Bought new Whirlpool duet washer 4.0 couple years ago. Started making load noise. Started checking and its the rear bearing and sounds of it will cost more to replace than to buy a new one. Found this page and after reading review after review, I will not spend a dime to fix the junk product from Whirlpool. Going to put in the dumpster and never buy another Whirlpool product. I have never seen so many complaints about a product and many being the same bearing problem. Where is our recall process? Its ok to rip off people over and over with no consequence. And why do large chains keep their product? Guess theyre in on the rip off.

Cabrio washing machine WTW8600YW0 - Had this washer for 3 years. Its been repaired a few times, but this last time theyve replaced the bearings 3 times and it only lasts less than 1 week. This $1000 washer is now going on the trash. I tried to get help from WP, to no avail. There is a reason these are only warranted 1 year. One thing I liked about it: the fast spin speed gets clothes drier. Every other aspect is crap. Cleans very poorly. You cant make it use enough water. The tub looks huge because it doesnt have a conventional agitator. But if you put much in there you will end up rewashing in small loads because then it REALLY cleans poorly. I bought this because my trusted appliance store owner buddy said he owned one. When I asked him lately he doesnt talk much except admits that yes they have had a LOT of trouble with these machines. The life is very short on them. The wonderful fast spin speed destroys the light bearings quickly. And it gets worse the more its worked on. Its a disposable $1000 piece of trash. Im an engineer, and whoever designed this should have his degree revoked. The type of agitator it has and the extreme low water is very hard on your clothes. One zipper left loose will shred your clothes. I wanted to love the thing, but I have to hate it because it is unrepairable. If you could control the water and if it lasted at least 5 years without having to rebuild it several times at greater cost than it was purchased for, I might be less than rabidly angry at WP. They know they are junk but dont care. You have few choices as they now own most brands, and they know this. I have a Speed Queen on order. Just a plain old simple washer.

This machine, like all other water sensor machines, will not let you wash a few items that are lightweight without filling the whole machine up almost all the way. The reason being is that if the items are light, they will float in the water above the water level and the sensor thinks it needs to put more water in and even with putting something in to weigh it down like a wet towel doesnt always work, nor should you have to do this. You will waste more water in the long run if you only have a few items to wash, ie baby clothes, underwear, rags, etc. I am so disappointed that I had no other choice but to get this machine.

Whirlpool Cabrio top load washer: nice job Whirlpool! You designed a washer that breaks if you accidentally wash a coin! For the second time in a few months, were fixing our washer because a coin was in a pocket. The coin gets sucked into the discharge pump and sounds like popcorn popping when it drains. It rattles around the inside of the machine’s pump until it breaks the plastic pump housing. You will know when this happens because there will be water on your floor. Did you ever consider a screen to prevent a coin from ruining the washer? God forbid someone leaves a coin in their pocket. Well, if you leave a coin in your pocket and wash your jeans, it will cost you a repair every time with this hunk of junk. This would be my last Whirlpool. It will actually be cheaper to throw this thing out and buy a new one, since it won’t be the last time a coin accidentally makes it into the washer.

After only 3 years using my Whirlpool front loading washing machine the inner tub is already broken. The repairman said the cost is just about the same as getting a new washer. After reading all the horrible reviews on the Whirlpool washer I WILL NOT be getting a Whirlpool. I am so disappointed in the washer and do not recommend it to anybody. Do not buy a Whirlpool appliance ever.

I have had no issues with my washing machine. Love the different settings. Washes clothes well. Dryer has minor issues like the drying dial stopped moving so I need to manually turn it off. It’s more of an inconvenience, but for the price it should work.

I bought a Whirlpool Cabrio 2 years ago and until last week it was fine. We got an error message that said we had to call for service so we called a local whirlpool repairman. The repair guy told us it was the control panel and it was going to cost between $400 to $500. He also said that he works on a lot of whirlpool washers and this is the first time he saw a machines control panel fail. He recommended that we call Whirlpool.I called Whirlpool customer service and after waiting on the phone for 40 minutes I was quickly transferred to customer resolution and was told that since I hadnt purchased the extended warranty there was nothing that they could do for me. I kept asking her, There is nothing that you can do to help me? And the consistent answer was no. I will never buy another Whirlpool appliance. This has been so frustrating to have an appliance that looks brand new and wont work. The manufacturer wont even try to help with fixing the problem. Amazing AWFUL CUSTOMER SERVICE.

I have the same lid closure issue expressed by many consumers and whirlpool refuses to acknowledge this as an issue, only recommends purchasing a new lid at $225. Lid design is flawed, metal L bracket connects to plastic housing/trim/side of lid, causing glass to pop out and stress cracks between screws. New models of same washer have redesigned lid, no cross reference part number or dimensions listed to determine if new lid will fit.

I purchased a Whirlpool Cabrio Washer In July 2014 for $937 cd. What a waste of my hard earned money! I have had nothing but issues with it since I purchased it. The retailer no longer sells them as they have seen nothing but complaints with them yet Whirlpool did nothing to help me as a client. It does not wash the clothes, there is such a foul smell even when cleaning it once a month as requested and the clothes comes out soaking and not rinsed properly. The technician came out and advised the washer was not broken. That is just the model. I have requested supervisors to call me back and most recently wrote the corporate office. I am out almost $1000 and in a situation where I have to go purchase a new washer as I just cant stand to use this product any longer. I am shocked they have not placed a recall on this model. What a poor product.

Whirlpool Cabrio Washer - A total waste of money. My clothes are never clean. The low water system is rubbish. It doesnt work! Check out my pictures below. That is the result of a 63 minutes wash cycle. Dont buy this piece of crap.

This is a horrible washing machine. All the clothes (and I mean small loads, medium loads, large loads) come out twisted and so wrinkled. I have never seen anything like it. I dont machine dry many items and so everything not dried that way has to be ironed. Also, there is white residue of some kind left on the clothes so the extra rinse must be used. How is that energy and water-saver sufficient? Again, the government EPA in its brilliance has screwed up another product. It also takes much longer to wash clothes, again, energy efficient? After reading the wasted time on other reviews of talking to Whirlpool, I didnt even bother contacting them. HE front loaders (which we had a Samsung that lasted 1 1/2 years before breaking down) and replaced by this top loading HE, are the worst. Give me back my old fashioned washer.

We purchased a Whirlpool Duet machine in September 2010. About a year ago, I started noticing tears and stains on clothing. Luckily, it was always on a washcloth or blanket, nothing special. Last week, it tore a 3-inch hole in my good jacket. I was not happy! My husband and I checked inside the drum and all around the seal. Neither of us found any rough edges. I thought if I called Whirlpool, they might have had a recall. They assured they had never heard of this problem. REALLY!!! Just look at all these e-mail complaints. Back to the old top loading - basic wash machine. Definitely not a Whirlpool!!!

I purchased an extended warranty with my product purchase and only a year and a half into using this brand washer the lid broke on one side at the hinge, it looked really rusty and like others I thought I was making a very decent purchase because all of my previous appliances were Whirlpool so figured Id keep up with the brand. Sad to say that was the worst decision I could have ever made for 13/1400 dollars for a washer with a light inside. Never again. They wouldnt even keep up the warranty because they said it was too expensive to repair it. Whirlpool is very bad for business...

I purchased the Whirlpool Cabrio (wtw6600sw2) about five years ago. Last year, the motherboard had to be replaced. This year, it started to have load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $75 to have someone look at it, and to fix it will cost almost $400, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. I called Whirlpool and my model does not have a recall, but models with same problems have been recalled. I will never buy a Whirlpool again!!!

My NEW Machine Top loader HUGE drum. Have problems with clothes not looking like they’ve even been washed, Spun so hard they are twisted all to heck. And white stuff - my oxy powder maybe? Not dissolved. My old machine was a Kenmore 30 yrs old. Thought I’d be able to trust whirlpool but not sure. Am I missing something in the loading process. Seems to read something bout not Covering the knob on the bottom. Is this true?

Havent even had the Cabrio washer for three years & Ive hated it since day one!!! First, our clothes dont come out clean OR come out with white streaks (changed soap, still happened!). Washing bedding is a nightmare! They are sopping wet & I have to wring it out. Finally broke down today & the repairman quoted over $600 to fix (paid $800). Take this piece of junk away!!! It cost me less to replace than get fixed; way to help the environment!

My Whirlpool Cabrio Washer is only 4 years old. I have had balancing & spin issues since day one. Thought it was just me. Constantly had to drain and spin after rebalancing. Now 10 days ago it cost me $250 to have it fixed. The aqcuator (?) Went. It wouldnt spin out. Now 10 days later it stops again. The appliance guy reads code. F7E7. He tells me the bearings are no good. Will cost another $400 and they need some special tool to fix it. IM DONE. My last set was 15 years old. The price is ridiculous and quality not worth what this triple capacity set cost.

I just love the durability of my machine and the features that it offers. It does a great job washing my clothes and I feel like its a solid appliance that lasts for many years and its good quality for the price.

Six months after purchasing my Whirlpool Washer model number WTW5000DW0 I would hear what sounded like rocks in the bottom of spin drum during spin cycles. Then noticed it was taking longer for clothes to wash and sometimes the water did not completely drain. Called for Service under LOWES warranty (the worst people to deal with). Tech comes removes a penny and dime and tells me that is the problem. Leaves. 45 minutes after he leaves there is the noise again. Call and set up for this Service Company to come back. Even though they went out of business prior to the appointment Lowes Service would not listen to me and insisted I stay home ALL DAY for someone who did not show up. Repeated calls to the Service Company resulted in nothing - phone disconnected.So finally after much frustration I am given new appointment with new Service Company - PARRISH. Tech comes in here five minutes and wants to know the sound, I explain. He checks out the unit and tells me it is a major problem and the part and labor will be costly. Best if they just replace the machine. His added comment - I see a lot of this. So if this machine is such a problem why was it not recalled? I am getting a replacement as I have warranty and machine was not a year old when problem started. Lowes Service Contract is another problem but I will deal with that later.

This was the first new appliance that I had actually ever had and I purchased it in October of 2010. After four months, it started make a grinding sound. I called Whirlpool and the repair man replaced the motor. Approximately four months after that, the lid got stuck and the machine would not respond. Same routine as before, but this time the transmission was replaced. While the machine was apart, I noticed the white insulating panel from the bottom was brown in a spot and looked as if it had gotten hot. A month before the 1 year warranty expired, the washer started making an intermittent grinding sound nearly identical to the sound made when the motor went out. This time a different service company was sent out my Whirlpool and the said that nothing was wrong. Now, the machine is out of warranty and has stopped cleaning close and during the spin cycle the you can hear water running into the machine constantly. Last months water bill shows a 40% increase in water consumption when nothing has changed to incur a larger bill. Seeing all these comments makes me wonder why the heck nothing is being done to force recalls on such poor products. Consumers should be treated with a lot more respect than this. I will never recommend a Whirlpool product to anyone I meet. In fact, I will strongly discourage anyone who is contemplating buying a Whirlpool washer machine.

I just bought a Whirlpool Duet Front Loader, and it vibrates excessively and wont fully rinse out all of the detergent. I have to take the tray out each time and rinse. Also, it has a musty smell.Whirlpool sent a repairman out to replace the shocks on a washer that is less than 2 months old. The repairman told me to use less detergent, but I am only using a teaspoon of powder detergent which is recommended and using Affresh once a month. There is nothing they can do about it till it is deemed unrepairable.

My mother and grandmother swore by Whirlpool washers. They were the best. So, naturally I never wanted any other brand - then came the digital machines. End of an era. My experience with my 1 year old digital machine has been very frustrating. I do not like it. I prefer the old system.

The machine never allows enough water to clean the clothes and I do not have the option to add more water or to spin the clothes again. The maker of this machine must think that people do not have the ability to know how to wash clothes or think for themselves. I need a washer that I can tell to add more water or just spin these clothes again. Very disappointed. I need an older model that I can control.

My Cabrio washer worked fine for approx 3 years. Within the last 9 mos there has been one repair/replacement issue after the other: pump, computer board, bearings, seal, etc. Whirlpool takes no responsibility. Worse purchase I ever made.

Absolutely read the reviews on this machine before deciding on a purchase. I have experienced with great frustration every issue addressed in other reviews. Clothes constantly have to be rewashed. The Quick cycle will leave your clothes in a puddle of water. But then there is no spin only cycle to correct that. I have purchased Whirlpool washers before with great satisfaction but this machine is not worth the money I paid for it and does not save me on water or electricity costs because of all the rewashing I have to do. Like others I am stuck with this machine until it dies. You lost me as a customer, Whirlpool.

Machine wont go through the whole wash cycle., Wash, Rinse, Spin. It stops and shows an error message and then I have to keep rearranging contents, over and over. This is worse if you try to wash a small load.

I bought this washer (Whirlpool Cabrio) about 4 years ago. A year or so later, it started leaking; based on reading the troubleshooting guide we found that this was because the feet would continually get out of balance. After painstakingly re-leveling the washer every 6 months or so the washer now consistently leaks - even though its balanced/level! $508 to repair a machine I paid $787 for. No thanks. I agree too with the other reports that it doesnt get clothes clean. I just figured this was a feature those of us got for trying to be energy efficient.

We have a Whirlpool Cabrio mod. WTW5600 XW2, ser. C12830447 he... H2O.. low wash system. Less than two years old. It does not get clothes or towels clean. I put 2 jackets in on bulky items and part of one of the jackets was still dry. They were two small childrens jackets. My husband and I wash as long as possible and on hot wash (which is not hot!). Should not take 70+ minutes to try & get normal clothes clean!Now the softener is draining into the wash with the detergent. Another service call. Learned you can only fill the softened bin half full or less. WHAT??? Our extended warranty is up soon and not sure what to do. We would like to get rid of this pile of junk but cant afford another washer bill. Also wouldnt want anyone else to get stuck with it. Its a shame a company cant put out #1 good product and #2 stand behind it. Bring all of the company production back to the USA or put out a better product and stop worshiping the almighty dollar. Im done with Whirlpool (which was the product to buy), but stuck with this washer for now until we are sure that the brand we buy performs as it should. What happened to the PRIDE in & RESPONSIBILITY of making a good product and standing by what youve made. As my hubby has said, if you have to buy an extended warranty, whats wrong with your product! Again worshiping the almighty dollar or is it you just dont care about the people who buy your product or its quality. Maybe both.P.S. Have contact you before without a response.

Purchased Whirlpool Cabrio top loading washing machine yesterday. When wash load is finished (dark load) white marks are visible on the clothing. It appears to be laundry detergent that has not dissolved. I am not happy with this washer and will be returning it.

I bought a Cabrio set in June 2007. Within two years, I had to have the barrings replaced ($800 job). Now, its two years later and Im getting a F50 code. The repairman put in a new part, still got the same code and left. I am out $970. I am a disabled vet/single parent and now I have to buy a new washer. Who is going to start the class action suit against Whirlpool?

This washing machine was already in the house when we purchased the house two years ago. In those two years, it has performed well for the most part. It has many different cleaning options, the clothes come out clean, it saves on the amount of water it uses, it’s quiet and I like the fact that it is a front loading washer.

I bought a Whirlpool washer (model wtw57esvw1) about 17 months ago. In that time, the same part has gone out three times. It happens every 5 to 6 months. The part runs 97 dollars plus labor. In the mean time, I am without the use of my washer. They say they are sorry, but they only cover their product for one year. After that, you have to buy their extended warranty so you can get it fixed by them. I feel that if I pay that much for a product I should expect at least 3 years without having to repair every 6 months! I have no washer. I am giving one star only because I have to.

54 weeks ago, I purchased a Whirlpool Duet Washer & Dryer. The first time I used the washer, it flooded my laundry room. After some grief, it was replaced with a second Duet washer some 53.5 weeks ago. Yesterday, that washer, 10 days past the 1-year warranty, failed. It gives error messages F06/E01 and wont complete a cycle. Calls to Whirlpool resulted in a refusal to acknowledge any product responsibility (out of warranty) but offers of extending the warranty for the cost of repair. I will never buy another Whirlpool product and will actively encourage any other consumer to shop elsewhere.

I purchased a new Cabrio Washing Machine and Dryer in March 2015. I have had 3 new washing machines thanks to the Customer Service provided by Lowes in Lindale Texas. The third washing machine has again lost its brain and the sensor to operate the machine. I have been waiting for the parts since December 2. Called it is still on back order. Unacceptable! It cost almost $60 dollars every 2 weeks for our washing at the Laundromat. Again unacceptable. All Whirlpool can say is We are sorry. When the machine works my clothes are beautifully cleaned using the new HE soap. Takes large loads and I love that part.I am sorry I bought a Whirlpool. Whirlpool would not work with me except to apologize and say the parts are on back order and I will get a call in 5 days for an update. These machines cost $900 each plus tax. They should work more than 3 months at a time. The first repairman could not explain anything. Said they were too new and he could not figure out what to do. The second repairman was more knowledgeable and explained what was wrong. Does not help that Whirlpool does not have an inventory of parts to take care of their customers.

As a consumer, Im very disappointed in this Whirlpool Cabrio Platinum washer. It does NOT clean your clothes. Many times Im washing my clothes twice, only loading a 1/3 of a load of laundry in it because of this problem. No matter what you do, it just doesnt clean your clothes. Has anyone considered putting a law-suit against the company. They will NOT stand behind this issue, NOR replace your washer with something that works. Maybe that is what it will take. DO NOT ever ever ever ever ever ever buy this piece of crap washing machine. You will waste your money, your time, your extra detergent it takes to wash your clothes AND the cost of the machine too! The MILDEW SMELL is horrible and no matter what you do you CANT GET IT OUT! Ive tried it all. Im just angry because I had to save money to purchase this set and it is a piece of crap! The customer service is just a runaround, they wont help you! They will just give excuse after excuse. They need to replace EVERY ONE of our washers with something that works!!! For the cost of this machine alone, they should do something to resolve this issue!

My Whirlpool Cabrio washing machine. f1 keeps showing up on washer on. Shuts off again and again.

Pathetic pathetic service!!! Unsatisfactory service!!! First of all, I would like to tell everyone who ever reads this, that please please please never ever use any Whirlpool products, as their service sucks, their response sucks too, and zero co-operation from their people, which will make you regret to have used their products in future. Please note I registered a complaint on the whirlpool no. **.The complaint was that the washing machine used by us had issues, the power button/ on & off button had come out, and this was clearly stated while registering the complaint. I get a call from Mr. ** (Representative of shree enterprises bibwewadi, pune) and the power button issue was well informed to him as well over the phone by me. He arrived to our place without any new material, he sees the machine and interchanges the buttons, i.e. the broken power button is replaced by other button from my machine which was less used compared to the power button. I had to pay a sum of rs. 400/- for the pathetic service I received from your end.I expect a response from your side within next 4 hours, or I might have to escalate this issue!!! (Please note Whirlpool team that I had submitted the same on your website yesterday, yet I have not received any response from your side). (Whirlpool rating- 0 out of 100). Thanks. (And whoever reads this, please tell me where else can I post this review of mine so that I shall alert everyone that how bad whirlpool service is)...

My washing machine ruined clothes with tiny rips. Small rubber pieces appeared in clothes. This happened during warranty but Whirlpool would do nothing. Finally, the bellow completely broke apart after 13 months. Repairman could not determine problem until this time. Whirlpool would do nothing.

How I wish I had read this board before purchasing! This is the worst washing machine made. Put your clothes in the sink, add water to cover two thirds, add detergent, slosh around slowly for a few minutes, wring and remove. You have replicated a Cabrio wash! I have complained repeatedly, had a repairman who assured me it was working properly (as designed, too little water, too little agitation). I was a lifetime Whirlpool client.

I purchased my Whirlpool Duet washer about 14 months ago. After about 8 months, I noticed that it had started leaking. It was under warranty and the seal was replaced no problem. I then started to notice that my clothes were getting small tears in them. Around January (13 months after purchase), I got tired of finding new clothes and jackets with rips and tears in them. I finally found that the plastic piece around the entrance to the washer was rough and jagged. I called Whirlpool and they told me they could send out a service tech to file down the jagged edges. They told me this was a common problem caused by the zippers on jackets hitting the plastic and causing it to become rough. Because it was one month out of warranty, I would have to pay for the service call. The lady told me I could try filing it down myself. I feel like I should not have to file down anything 14 months after purchasing a new washer. I feel like I should not have to worry that my clothes are ruined every time I wash them. If this is a common problem as the lady told me, it appears to me to be a design flaw and should have a recall. I have lost several outfits and jackets due to this machine and I am very frustrated that Whirlpool would not stand behind their product.

Washer keeps saying F1 and it wont spin. In the middle of load it will stop and it would say F1... It started just a year when we bought it. Now its two years. Its really broke. Before it would say F1 then I give an hour then try again and it works but now no matter what I do it really wont work... I dont know no one who could help me whats this F1... So sad. Its not cheap washer but its junk.

Whirlpool Dishwasher purchased at ABC Warehouse in Chesterfield, MI and was delivered on 10-2-2014, and one year later, we noticed that the tips of the lower basket were coming off. We contacted the holder of the extended warranty (5-yr.) and also Whirlpool. Both replied the fault was cosmetic and was not covered by warranty, that only mechanical/electrical components were covered. When we were buying the extended warranty, we were told that we were covered for all issues that may occur. We werent told cosmetic flaws were not covered. I guess consumers should, before buying a new product, make a specific list of possible problems, and make sure whats covered and not covered. We have been unable to resolve this issue.

Bought this washer in May of 2019: Whirlpool - Whirlpool - 4.5 Cu. Ft. 37-Cycle High-Efficiency Front-Loading Washer with Steam and Load & Go™ XL Dispenser - Chrome Shadow. Model: WFW6620HC. SKU: 6313774. Paid over $1,000.00 for it. FIRST TIME washing our sheets, we had snags & rips. I immediately called and was referred to Whirlpool and then referred to an outside repair company. They sent a technician out who said everything was functioning properly despite having ruined 3 sets of sheets (these were not all washed at the same time & I didn’t realize they were being snagged until making the beds).I continued to use the washer - clothes were fine, but yet again, MORE sheets and now comforters RUINED!!!! I called YET AGAIN after troubleshooting the problem myself and finding that the drain holes in the drum had metal pieces sticking up causing the items to snag & rip. Another day taken off work to stay home for the repair. The repair guy comes out, the part was broken. So now I’m left once again with a faulty washing machine AND no ETA on when the new part will arrive and be installed AND having to take yet another day off work.7 sheet sets, 3 comforters, multiple shirts, & multiple bathing suits RUINED & was told there was ‘nothing they could do!’ I will NEVER EVER AGAIN purchase anything with the Whirlpool logo. It’s JUNK! Just an FYI, this was initiated in May of 2019 and it is now the middle of September 2019 with no fix updates. Who can go months without doing laundry???? Once again, poor customer service and JUNK of a product!

I have a two-year-old top of the line Whirlpool Duet Steam washer. Cleaning performance is adequate at best, but my biggest complaint is about the visible mold buildup that collects on the water dispensing plate as well as on the detergent, bleach and softener dispenser and rubber lining of the washer opening. I have cleaned the removable detergent dispenser weekly since purchasing. The water dispensing plate has a continuous buildup of thick black mold that can only be removed with a tooth brush and bleach and only a small portion of those openings are reachable. I have cleaned the machine with Affresh as recommended and exactly as the manufacturer recommends. Nothing changes! I contacted Whirlpool and was told this was normal for all washers in which some moisture always remains and that I should continue to clean and leave the door and dispenser drawer open to allow the areas to air dry. So, I have done all of those things for the past year and nothing has changed! I received notification that a class action suit had been filed against Whirlpool for this mold issue but have not been contacted in any other way. Not only is this mold visibly disgusting but certainly is worrisome from a health perspective. When I contacted the company a second time, I was told there was nothing that could be done and it was in no way a design flaw on the part of Whirlpool.

I purchase almost four thousand dollars on WHIRLPOOL appliances this month. From: HOME DEPOT 114 FEDERAL RD DANBURY CT. Received the items a week and a half ago 9/15/18. I was told to exam item no scratches, dents etc. I did that and had them put in place. I didnt get a chance to use washer until the fourth day. At which time realized it didnt work. Went over to store and they gave me Whirlpool repair phone number. Called and was told they only repair Mon - Fri 8am-4pm. I work every day until 5pm and off weekends. Told Whirlpool repair just that. THEN I TOLD by girl I was speaking to (Whirlpool repair) I COULD JUST RETURN THE WASHER TO THE STORE (Home Depot) MYSELF. I WAS FIT TO BE TIED. I told her, What should I do? Carry it on my back? I have never been treated so poorly. I just moved here from Florida, started a new job. I cant take a day off to have the washer that should have worked fixed. I will never purchase anything else from Home Depot if this is how Im treated, and Whirlpool their customer service stinks!!! So now Im stuck with a washer that doesnt work and a company (Whirlpool) wont accommodate their customer. (Whats wrong with this picture???)

I purchased a Cabrio washing machine and discovered multiple repair issues over the last few months. I have had to replace a pump for $85 and now the machine will not complete a cycle. I found out the the whole thing is rusted above the barrel which is causing a leak in the back and leaving our floors covered in rust shavings. From my research and reading others reviews and issues, they pay for a serviceman to come out and still it does not solve the problem. My husband is a student in college and we are living off student loans. We bought this machine because we trusted that a Whirlpool would last and be a good investment. I am very displeased on this machine and doubt I will ever put my trust in Whirlpool again. I called to complain and got the typical response I have read others got. I am not paying for a service call when it will not fix the washer in the end. I plan to file complaint after complaint and encourage any class action suit against Whirlpool for producing a poor washing machine and misadvertisement on this machine. I will move forward in this. I feel that as consumers we have a right and should have a sense of ease when you spend $900 on a product that it should work and not give out as it has so quickly. If there has been multiple people with common complaints, then there should be a recall on this washing machine.

Sounding like a broken record, this washer is such a disappointment! I had high hopes for this top loader and thought I did enough research. Bought a Cabrio in Oct 2016 and have never liked it. They will have you believe it’s your fault... the wrinkly clothes, the clothes not clean enough, the white marks over all your clothes... you can’t change your detergent or softener enough and change the amount enough... it will still be there. So disappointed??? Want my front loader back!

I purchased the Whirlpool Cabrio Washer WT5500XW2 from Lowes on 9/12/2012, which turned out to be the worst purchase of my life. It did ok for over a year. It had always been noisy. Now it sounds like a jet airplane when it is on the spin cycle. This machine is not yet 2 years old. Do not buy a whirlpool washer. They are Junk. Plan on getting rid of this piece of junk and buying a new washer. Dont waste your money on Whirlpool!

We spent a lot of time researching to make sure we were making the right choice, found the one that was right for us. When it got delivered there was a problem though, the plastic scratch protector film they put on the doors for delivery left an adhesive residue that looked like dull spots all over our new shiny black doors. I immediately opened up the owners manual to see how they recommend removing this blotchy sticky residue, assuming we werent the first ones to ever come across this problem, unfortunately they only provide generic cleaning tips. So I went to their website and found what I was looking for. I tried all of the cleaning methods they provide, none of them even came close to working. So I grabbed some adhesive remover and tried that, it worked great to remove the residue however my microfiber cloth (which they recommend explicitly) started leaving scratches all over the finish.I called the customer service to see about getting a new door delivered, thinking this wont be more than a 5 minute phone call since I had followed all of their steps they provide both in the owners manual and on their website. Heres where I find out that their policy DOES NOT cover scratches/cosmetic damage, period. I tried reasoning with them, I had them read their own recommended cleaning procedures, and we both concluded that I had followed their procedures to the T! You might think that if the all of the typical procedures didnt resolve the issue, that would be the point where the customer service reps would have the ability to make a decision that satisfy the customer, you would be wrong! They kept telling me over and over that their policy doesnt cover cosmetic, therefore there was nothing they could do. It was delivered with a defect of sorts, how is the customer responsible for that? The only way I can see it having worked out in my favor is if I had never tried to clean it myself and immediately called customer service, I still fear they would have given me the same line of cosmetic damages are not covered even if I would have tried each procedure with them walking me thru it over the phone. Lesson learned, I will never purchase another Whirlpool product!

I bought this Whirlpool Cabrio from Lowes June 2016. It doesnt wash the clothes at all, always detergent marks or clothes just not clean. Now it is making some loud noise during washing cycles (sounds like motor is dying) and I now I have to wait for someone to come out and fix it during a 8-5 time span, so I have to take off work. I will never buy whirlpool again. So very unsatisfied!

We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age.

My first washer a Sears Kenmore lasted us 25 years before giving it to our son who used it for another 10 years. This machine is compatible with that one. Both are simple with a few of bells and whistles. That is remarkable in todays gotta have all of the fancy gadgets mindset. The Whirlpool machine does a very good job of washing clothing...period!

We have had this Whirlpool Duet WFW9150 washer for 7 years, doing 2-4 loads a week. Overall we are quite satisfied with it. A few complaints: We are on a well, and so get the odd bit of crud in the water. The machine has filters on the inlet lines, but you must pull it out from the wall to get at them. The filters are hard to remove. If something goes wrong--power blip, or sensor something, you have to restart the cycle. There is no way to continue from where you left off. There are features I wish it had: Rinse with warm or hot water, a spin only cycle, And Im in a hurry and it isnt very dirty cycle (Shortest cycle is almost 2 hours). Whirlpool doesnt have a service center for our area. If we need repair we need to take it into town. This is inconvenient.

They are good washers but they are overpriced. They have way too many functions for doing laundry. I know everyone wants their washer to do it all but the machines just can’t. There is no washing machine in the world that can sense a stain and pinpoint it and remove it.

My wife and I purchased this Cabrio washer 6 years ago when we got our new home. I have replaced the discharge pump 2 times, and approximately 2 months ago, we developed a noise so loud it was like a jet engine landing. I called our appliance store and paid $100 for an estimate, only to find out it will cost $973.00 to fix it. When we bought this, I was told it will be the last washer we will ever need. Ill never use Whirlpool again and recommend no one else does, either. I wrote to your customer chat line and basically the reply was Sorry about your luck. I know Im not the only one with this issue.

Whirpool WFW9550WW-00 Front Load Washer - Washer was purchased 08/09/12. No problems until 07/12/15 when washer stopped working mid-cycle. Motor control board needs to be replaced, actuator needs to be replaced. $500+ Our local appliance store suggested we call the Whirlpool customer relations number and ask for the parts to be sent free of charge. We would pay labor. They gave us the model number, serial number, the diagnostic info. Long story short, customer service told me she didnt know why I was told to contact them. They can not predict the life of a machine. Less than 3 years for this machine. 22 years for my old Kenmore. Our old Kenmore never had a problem, but we thought that we should replace it in 2012 in case something happened with old machine. WISH WE KEPT THE 22 YEAR OLD KENMORE.

Agreeing with many. How disturbing to buy a Cabrio Whirlpool washing machine about 5 years ago. I might as well go down to the river and wash my clothes. The bearings went out which means I have to be the spin cycle. I am hanging out my clothes on the line - very wet - until my husband buys the part and fixes it himself. I had my maytag for 25 years. An awesome, dependable machine that we laid to rest because of rust. We should have gotten another drum instead of buying this machine. Where are the engineers that are making dependable appliances to last a LONG time? We have not gotten smarter. Or we only care about the all mighty dollar. Make something to last a short time so that you have to buy again. We will do some extensive research the next time we buy a washing machine. Do not buy this machine!

In 2005, I purchased a Whirlpool front-loading automatic washer for $700 plus. The machine had to have repairs on it several times at my expense. Then in 2010, I had to replace it and spent another $700 plus on the same type of washing machine. Whirlpool would only discount $100 of the cost. The second machine three years later is now also needing repairs. I spent a total of over $1,400 in 7 years on two washing machines not including repairs and parts. It also took forever to find the parts, so I went without use of a washer for one month. I called customer service and said they couldnt do anything for me the second time around with them. I will never buy another Whirlpool ever! You would think a company would care about their customers but they dont. They make their stuff cheap and charge an outrageous price.

I bought A Washer Whirlpool and right after 30 day of the purchase my washer went bad and I called the Whirlpool Services and they told that will take about 30 days to come out and take a look at it. Are you crazy!!!! Freaking garbage that is what is. Never would want to buy Whirlpool again specially with that type of customer services they have..

I have had the machine pair (Whirlpool Cabrio Platinum) for almost 4 years and up until a few months ago I LOVED the washer. I was advised when I bought the machine to make sure to read the manual, which was very helpful in learning to use it properly. I have never had residue on my dark clothing or ever had the clothes come out partially dry. I use liquid HE detergent nothing powder goes in the machine. I also read many reviews before buying it and a got some advice from them. I have washed king size comforters with no problems. Everything has always cleaned very well. The only issues I have are that when bleach was used in a previous cycle. Ive had a problem with the bleach not being fully dispensed and ending up in the next load. Fortunately it was just towels and not darks!!! Although, I had just bought the towels and now they look tie died which was very upsetting to me. I learned to add water to the bleach dispenser to dilute it and that issue seemed to dissipate. BUT NOW... I COULD THROW A TANTRUM. I PAID 1800+ FOR THE PAIR AND THE WASHER IS SHOT!!! A pretty common problem with the Cabrio from what Ive read. It started by making a very loud noise when spinning, like a helicopter was landing in my laundry room! I continued using it, I even thought the sound was getting better after I did the clean cycle. The last load I did would not complete the cycle because it kept reading that it was unbalanced and unfortunately it was a load of heavy wet towels. I was far from happy when I had to remove them and go to a Laundromat. Needless to say its the bearings and to fix its very costly. I cant even fathom that a less than 4 year old machine needs to be repaired and the cost is roughly half of what I paid for it!!! I do know I will NEVER buy another Whirlpool. What happened to making things to last??? Next machine I will definitely get extended warranty. I can honestly agree with all the other reviews... THIS MACHINE IS HORRIBLE!!!

After almost 5 years of satisfactory performance, our $1200 Whirlpool Duet washing machine WFW9400SU1 requires repairs costing over $1100. Similar to another complaint listed, some parts rusted out, leading to extensive damage during use, which we realized only after the spin cycle became incredibly loud. Now the entire gut of the machine (bearing, drum, arm, casing, etc.) needs to be replaced - $900 parts and $200 labor. I trust my repairman (who said theyd seen this type of problem before with Whirlpool) especially because he recommended buying a new machine instead. I called Whirlpool, and they said they could do nothing for me which made me very angry. This is a mechanical problem that could have been avoided by using proper materials. Whatever happened to the washing machines that would last 15-20 years?

Purchased new Whirlpool washer from builder - never worked. Serviced 4 times by Whirlpool - does not wash, does not sense, shakes like crazy. No resolution from Whirlpool - worst customer service experience.

Bought the washer on November 2013. Today 1 August 2016 the driving motor broke. The cost of the motor is 650.00$. I will not buy another Whirlpool product ever.

This Whirlpool washing machine is incredibly annoying and slow in everything it does. First off when you press the START button it takes 2-3 minutes before it decides to do anything, like maybe add water (except click, click and more click). If you have pressed the start button and you want to stop it to add something... again you have to wait almost 2-3 minutes before the lock is released and you can open the door. I am at 2 hrs and 15 minutes as I write this on the LIGHT WASH cycle with extra rinse and its still going. I have never seen anything like it. Cant imagine how long a HEAVY CYCLE takes. Cannot even try to measure the time. I put the load in and go to work and hope its complete when Im done 8 hrs later.We had a Maytag for 15 years with no issues (other than a drain hose cracked and had to be replaced) and it was time for a new one with a move to a new place. The sales associate convinced us this was the best machine at the time... Well what a mistake that was. There are no complaints about the actual washing. Everything comes out clean but I suppose taking that long I cant imagine why it wouldnt. I certainly cant recommend a Whirlpool washer to a friend, because I dread the thought of doing laundry at this point.

We acquired the Cabrio Six Sense washing machine through the purchase of our new home, and quickly realized why it was left behind. This thing is pretty and has lots of bells and whistles, but that is where it ends. I am very surprised to find out that Whirlpool put such a piece of junk out for purchase. I have owned Whirlpool products in the past and had great performance and quality. We will be pulling this hunk of junk from our laundry room and installing the GE washer that we already owned immediately. Anyone want a free washer?

My husband and I purchased a Whirlpool Washing Machine & Dryer a year and a half ago. As of current, the machine has stopped working. The machine will turn on but will not agitate. It makes a horrible grinding noise. The type of washer we purchased was a WTW4900BW0. Whirlpool told us we should have purchased the extended warranty. But, I feel we should get more than a year and a half out of a machine that cost $650.

Cabrio - In Dec 2013: Ran the Clean washer cycle and it would not cut off. I had to shut off manually. Called the company and they sent a technician, who said he fixed it and that everything was good. Fast forward to Feb 2015: Tried cleaning the washer again. When I left the house there were 10 minutes left in the cycle. When I arrived home 7 hrs later, the washer was still running and my hot water heater had cut off. I had to reset via the circuit breaker. This will be my last Whirlpool appliance for a long while.

I purchased a Duet several years ago and did not have a clue as to the problems everyone was having. Over the course of ownership I called the city to determine if we had a sewer leak. I had a plumber inspect our pipes. I felt really stupid that it took me this long to figure out it was the washer. I knew it smelled like mildew and have been using vinegar, afresh, Clorox until I am blue in the face. I didnt figure out that the sewers smell was also the same as the washers until I got on line and read about these machines. Finally, I lifted up the gasket around the door and it was completely black with mold. No amount of afresh was going to fix this problem. Do not purchase these front loaders. Feel like they should have been recalled and I really dont understand why they are still in circulation. I have also been having health/breathing issues and I cant help but think the mold is causing my illness.