I purchased this washer over 8 years ago and we have been using it 3 to 4 times a week/ 52 weeks a year since. It has performed flawlessly up until about a year ago when it kept given me uL error. Everytime I wash the basket always spins wobbly and unbalanced it seems. I checked the Internet and it turns out others have had the same problem. The solution was to replaced the 4 springs supporting basket and that fixed the problem. Been working ever since.

I bought this piece of junk Whirlpool Cabrio washer two years ago and it’s been nothing but junk. Just like everyone else, this thing has never gotten my clothes clean no matter what I do. Anything with a drawstring or straps gets ripped up or stretched out. It’s loud and shakes, even though it’s leveled. Now, to top it off, it’s leaking water from the basket seal. I called Whirlpool and they couldnt give a damn. Since it’s out of warranty, it’s my problem, even though she said they know this machine has a lot of problems. So now Im stuck either fixing this thing or buying a new washer. Every appliance in my house is a Whirlpool and Ive had nothing but problems with several of them. I thought when I bought the brand it was a good brand and they stood behind their stuff. Boy, was I wrong! I will never buy Whirlpool again! They should recall this washer!

Does not get your clothes clean. They come out of washer smelling due to lack of water. Darks have Detergent Residue on them. My t-shirts have holes in them. Bought this machine in 2010. Just purchased a Whirlpool top load with a Agitator and I am very pleased with the results. We never had any problems with Whirlpool products but this Cabrio should be taken off the market, faulty advertising. Talked to a Whirlpool rep and she told me to bunch up clothes and place around outside edges of machine for best results but did not see any difference. Do not buy this washer. You will be wasting your money and you will be buying a old traditional washer, with an Agitator is your best bet so you can control the amount of water you use. I hope this helps one that is thinking of buying the new technology top load Cabrio with HE.

I purchased a Whirlpool Cabrio in 2009. It worked so-so over the years but recently stopped completing cycles, citing false load balance errors and leaving towels and sheets sopping wet at the end of a cycle. Three repair appointments later, and still no success. I am thoroughly disgusted that such an expensive machine only lasts four years. Based on the service techs attitude toward the machine and other consumer comments, Im guessing I will have to replace it. You can guess it will not be with a Whirlpool machine!

We purchased Model WTW81920758200YW0 on September 8, 2012. Its performance has been unsatisfactory, not cleaning the clothes as advertised. Not long after the warranty expired the main bearing failed, bringing a local service technician and we were left with a bill of over $300.00. Yesterday, the machine stopped in mid-cycle. The display went blank and the lid lock would not release. I called a local service company for a visit and the soonest a repairman could show up was next week.A call to a service we had used for the bearing surmised that without knowing the cause of the failure they could only guess that a circuit board was at fault. That visit would be over $300.00 with labor and materials. That was the last straw. We broke the lid lock to retrieve the contents and took a ride to buy another brand of washer. We went back to the appliance store where we purchased this machine to buy a Samsung front loader. The salesman apologized for selling the Cabrio in the first place. Good money after a bad product.

We purchased the Cabrio Whirlpool washer from ABC Warehouse October 18, 2014. They said if we purchased a washer of higher quality it would last longer. We have bought Whirlpool washers for over 40 years. When our last one only lasted for three years they convinced us to spend more money over 1000.00 witha purchase of a 5 year warranty 6 days over the warranty. It is junk. The bearing went out costing 600.00. They graciously offered to sell me another washer. WOW, everyone is sorry that we have this problem BUT you are out of luck. Are they kidding? I will never buy another Whirlpool. They use to be the top of the line but now I feel we are in a throw away world and talk about consumer rip off. FLEECING OF AMERICA AT WORK!!!!

I purchased my Whirlpool Cabrio Washer (WWT5640xw0) at Lowes in East Orlando in 2009. It has worked without issue (other than a slight odor) from then until today, 5-1-12. It has now refused to agitate or spin any clothing, it emits a slight burning smell from the basket, and the basket, when it does decide to spin, spins about as fast as a merry-go-round, banging into the sides of the washer (causing the metal on the sides to bulge out every time it strikes them). It is self-destructing.I called Whirlpool, and they simply refused to address any questions, once I told them that I did not have an extended service plan and that my unit was older than 12 months. I informed them that I refused to pay for an ESP, because I refuse to pay additional monies in order for the product to perform as advertised. They were rude. I said bad words. The call ended.$600 was gone. And I now have to run out and buy another washer, and I can promise you it will not be a Whirlpool. I am a local law enforcement officer. I would love to speak with an attorney about this if a class action suit is pending. I am beyond pissed. My moms chartreuse-colored Maytag still works after almost 30 years of service to our family. It required a new drive belt at somewhere around year 17. The belt cost $45.The Whirlpool CS rep informed me in a surprisingly snarky fashion that it would probably cost over $360 for the total cost of repair and that the only way to know exactly how much is to schedule a service call. I was also told that I would be on the hook for $100 for the service call even if I declined the repair.

Whirlpool Cabrio washer (WTW6400SW2) - After a few years of working, my washing machine lists a code of F50 and will not spin. After three visits from a repair company, they couldnt fix it and said we need to buy a new one. It seems like an electronic problem, but we have to replace the whole machine. Consumer Reports says a machine should last 10-14 years. Numerous people online have stated the same issue with the same model. More than one person stated there is already a class action lawsuit on this machine? Please help. Who can afford a new expensive machine after a few years of service?

At some point, Whirlpool should accept the fact that they should not sell this machine. Word of mouth spreads fast! Im hoping it will make a big dent in sales because I know then they will listen and act! I purchased it in 2006 for $800, thinking this Cabrio 6400SW is a dream, I can get more done in less time (at that time, there were seven in our family). However, problems within the first year, F1, but I was happy and still under warranty! It was fixed, only to start the problem again. This time, not under warranty! I really wish I had said yes to the extended warranty! Even the repair guy Whirlpool sent suggested it may be a good thing to get the extended warranty if I were you! I think he was trying to tell me something!My naive thought was, why spend more money we did not have? After all, it is a new machine! I did not comprehend that any company could sell and continue to sell something that was clearly a defective machine! Nor did I entertain the thought that a company would not stand behind their product! It is now 2012, I still have the machine because we have dealt with it and have/had no extra money to throw out at it. I have dealt with F1 for several years and did not contact Whirlpool, mostly out of lack of time to research what the deal was and if others were experiencing the same. In November 2011, after reading many complaints and frustrations on the internet and what results they got, I called Whirlpool. Using a level head, sugar sweet persona and a mindset of disbelief that Whirlpool would allow such problems, the customer service girl did her best with what she was told to reply with (meaning, there is nothing she can do). It is then that you ask to speak with a manager or director. I won in getting a repair guy out to fix the F1. They made it sound like they were doing me a onetime favor. The machine board was replaced, the repair person also thought there was an obstruction in the hose and he could fix it, but it would cost us money and suggested we try our hand at it first. We did find an obstruction and for one week, the machine was quietly working beautifully! Whirlpool even called to see about how it was working and my husband had answered that everything works well, not knowing that Ld is our new problem. Ld had started to pop up at the end of that week.So here it is July and Im so frustrated trying to get wash done. Im thinking of all the wasted time, all the wasted electricity and energy Ive spent trying to get this machine to work! My kids are trained to hit stop/pause if they hear it beeping. Some days we cant even get the clothes to spin dry. I try different cycles to get the machine to start and often have to cancel the cycle and change it to another cycle to get the machine to continue. Is there a smell? Yes, and I run the clean washer cycle twice in a row just about every other week now. That doesnt even seem to clean the washer anymore! Tangled clothes sometimes. Ld always, uL sometimes and a sound like it is trying to do something but is stuck. Lots of laundry to do! No money to fix it! Whirlpool needs to stop selling an inferior machine! I know one thing. Never Whirlpool again and I tell everyone not to go with Whirlpool Cabrio. Even one of my co-workers had one and bought a new washer (not Whirlpool) because of problems with her Cabrio only after three years! Do not purchase a Cabrio!

This washing machine is a piece of junk. It broke down exactly 2 days after the one year warranty expired. Home Depot said there was nothing they could do and Whirlpool said the same thing. This washing machine was not used on a weekly basis. It perhaps washed 20 loads during the course of the year. I had many issues with the sensors before it broke down completely. Sometimes, half the clothes would be dry after the entire cycle. I was so angry that I had a local independent contractor come in and look at it. He said the motor was broken and needed to be replaced. So much for $700 down the drain. I will never buy a Whirlpool product again. This was the worst experience Ive ever had with an appliance.

Piece of junk that tears up clothes but doesnt clean. Company has ZERO care for their customers. I will never buy Whirlpool again. We called and called and called. Washer took two hours for a normal load. Crust and odors still there. Dryer was fine.

I had the bearing go bad in the tub after a few years of service. It cost hundreds of dollars. As an engineer, I look at this and it is a design made to fail. The seal design is inferior compared to old washers that had a shaft seal made to be on a spinning shaft. This is a rubber lip seal that is going to wear because it is using washer as a very bad lubricant! When the seal goes bad, and it will, the water runs down to the bearings and destroys them, and you have the replace the whole tub as a $300 part!

I have a front load Whirlpool Washer and it has leaked within 6 months of having it. The rubber piece was replaced and it still leaked. Whirlpool wont take responsibility for its product. I have to put towels down around the washer every time I use it because it leaks. I purchased this because it is more economical to use a front load but not when water is leaking from the washer.

Since there is only two people in this home, we decided to go for the smaller front-loading machine. This was purchased in 2012, still running. It does a clean wash, however common sense does remind people to not over-load a front load washer. If one follows directions, it gets the job done, and ones machine lasts longer without problems. Thanks.

Informed that because washer was 1 year out of warranty. It was 2 years old. Parts were not guaranteed. Cost to repair $400.00 including labor. Maytag Store came to my rescue and it only cost $200.00. 2 years later, washer is not filling with water correctly. Have mixed feelings about repairing or replacing. If replacing, how to select a reliable washer. How do you select, if when we purchased this washer it was rated very high. Whirlpool does not help with any issue. They were extremely rude. Felt helpless dealing with them. Need a new washer and have no idea which brand to go with.

I purchased a Cabrio high efficiency washer in 2011 and have had the glass top lid crack twice. The hinge is rusted, shedding rust all over the corner of the washer. It is a design flaw, for I see others have had the same problem with this particular year. I have also looked at the newer versions of the Cabrio and the lids have been redesigned. This lid should be recalled and replaced with a newer version, because this lid will always rust and crack with use.

We purchased this machine new and took delivery on 5/21/11. We did not start using this until late August of 2011. In late November we noticed a loud noise from the washer. When we contacted the sales company that sent out a repair person who informed us the bearings were defective. We have been told the parts are on back order for another 2-4 weeks. It has already been 4 weeks since they were out. Whirlpool was no help. They first claim we must have overloaded the machine, then relented saying that things happen. Either way I am without a washing machine we paid $1000.00 for another month; yet they will not extend my warranty at least for the time my machine is down. I am now worried about the damage that this unit may have caused to my new home due to water leakage, let alone the added expense to due my laundry since I must now use a service to provide for a washing machine I own.

Bought this model #WTW8500DC from Lowes in 2015. Ever since had problems. Stopping in the middle, not starting, recently keeps running water, lid lock issues, had multiple service calls and multiple hardware changes, paid extra for extended warranty from Whirlpool hoping that within a year all problems would be gone after so many repairs. Boys I was wrong. After spending around $1200 between this machine and the extended warranty, three year later after the warranty expired now I am stuck with this non-functional piece of junk and looking for another washing machine. Would love to hear from Whirlpool if I stumbled upon a lemon, or three year is expected life of their $1000 plus machines.

I bought this washer (model WTW7800XW) on 12/23/2010. Never happy with its performance from the beginning. Within the first 18 months, the lid hinge completely rusted and broke. The repairman stated that the hinges and glass lid would need to be replaced at a cost of over $400. We paid $899 for the washer. Instead of paying that much, not knowing if it would only last another 18 months, we removed both hinges and removed the lid manually to use the washer. After complaining to Whirlpool about the problem, they thanked me for the info so they could use it for the future. The latest problem to arise is the light inside the washer. The mount for the light was made of steel and has completely rusted away, so the light is just hanging inside the washer. Whirlpool needs to step up and resolve the issue with an extended warranty for these machines.

I have had this Whirlpool Cabrio washer for 4 years. I had to rebuild the drive unit once and now the control board is bad. If I didnt do my own repairs I would have spent well over the cost of the washer in the 4 years I have owned it. This is the worst washer on the market. Not to mention Whirlpool support will not work with you at all. DO NOT BUY THIS PRODUCT.

Ever since I purchased your washing machine, it has sounded like a diesel truck or cement mixer. You cant hear anything over the noise anywhere in the house.Have had two repairmen out to look at it and they say, Thats normal. I have a friend who has the same machine and it doesnt make noise like this one. I will never buy another Whirlpool product again and hope this blows up before the warranty expires. Also the tub is falling apart. What a piece of ** this machine is. You should be ashamed to put trash like that on the market.

I purchased the Whirlpool washer in February 2019 and delivery was in March. As stated in my previous reviews for the manufacturer, and subsequent repair calls, three; from the first time using the washer, it didnt fill properly for the amount of the clothes in it. A piece of paper towel never got wet through the whole wash cycle. I had to resort to raising & lowering the lid numerous times to get to the correct water level; adding water with a container or just pressing down on the switch under the top cover; 4-5 count. Needless to say very time consuming. As for hot water for doing white clothes, forget about it! It seem to me its the same problems with this whirlpool washer thats been happening with most of the other reviewers/purchasers. Did Whirlpool ever think about taken back one of these problem washers and checking it out for themselves? Maybe installing a clear plastic lid to monitor water levels at different wash cycles? Hot water temps when called for? Are these negative reviews ever seen by Whirlpool? Or in the trade is it called.... JOB SECURITY? Any more detail required? Cabo

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

Whirlpool Duet Sport W & D purchased from Costco in mid 2007 for $1600. Costco gives an additional one year warranty, totaling three years. Both have worked exceptionally, I must say -- clothes come much much cleaner, keep their color, and last much longer vs. top loaders (Im sure the water softener helps). Two separate techs just confirmed the circuit boards went on the washer ($450 with labor) to replace. Washer looks brand new, but now will be going to the curb.

The washer buttons stopped responding after 19 months. Lid lock sensor didn’t work. Replaced control board because new sensor did not fix it. Went bad again after a week. I have to replace it. I think 1 year warranties are not enough for a major appliance.

My Whirlpool Cabrio WTW5550xw0 has had many problems. It started with the lid lock error, replaced it, lasted about 2 weeks, and got another one. I did the diagnostic test that pointed me to the actuator, replaced it. It worked for 2 weeks, got another one, and then another one. I was getting a bad reading from the control panel, replaced it, and that worked for a while. I found out that the actuator had a little water drops on it. I figured that it must be the tub seal, so I replaced it. That lasted about a week and a half, and it started dripping again. Now, I figured it is that the transmission has bad bearings, that causes my tub seal to leak, that causes water drips to go onto my actuator, causing a failure in that, which can give me all kinds of bad readings on the diagnostic test. I have replaced at least half the cost of the original purchase price on a year and a half old washer. I also bought my son a Whirlpool Cabrio washer a few months before I bought mine, and he hasnt had a single problem.

Bought the washer on November 2013. Today 1 August 2016 the driving motor broke. The cost of the motor is 650.00$. I will not buy another Whirlpool product ever.

The Whirlpool duet model wfw9150ww01 washing machine is a piece junk. After using it for two years, the bearing has gone out on it and it sounds like a freight train. It will cost $600 to repair it. We only paid $575 for it. What a rip off. Whirlpool makes junk only. Buy something else.

I saw on the Today Show that my Whirlpool Duet washer, purchased in 2008 was a mold-producing nightmare. We are now part of a class action lawsuit that seeks redress. When I called Whirlpool Customer Service, I was fed the company line that the problem is that we dont clean the machine regularly. The instructions call for monthly maintenance, but the rep said we need to wipe it dry after each use. This is an original defect in the machine that Whirlpool refuses to own up to. We had been Whirlpool devotees for years but will never purchase another Whirlpool product.

We purchased a new Whirlpool washer in March 2010. Yesterday, 2/19/12, the washer stopped working. We called a repairman who checked the machine and told us the motor needs to be replaced. We called Whirlpool today, 2/20/12, and were told by their customer service department that since we did not have an extended warranty. We told them that we believe the motor should last more than 2 years. Their response was that if the motor lasted more than a year that was all they cared about. The only thing they would do is replace the motor if we gave them $299.00. I think it is very clear that Whirlpool knows it makes inferior products as they fail to stand behind what they make. I will never buy another Whirlpool product and would advise anyone who is looking for a washer to buy something other than Whirlpool.

It goes off balance, frequently. It is moldy and stinky. I wipe it out, use a cleaner and leave the door open, but it still stinks. I am getting rid of it and buying a Speed Queen top loader. I am extremely disappointed in the front loader Whirlpool.

This washing machine started giving us trouble just a few months after purchasing. Have had repairman to our home 5 times in 3 years. Last time repairman came he said future repairs would be very expensive & we should purchase another machine. Whirlpool will not have my confidence again unless they recall this machine & fix all problems.

I bought this Whirlpool Cabrio washer three and 1/2 years ago and the assembly which is basically the transmission and the assembly which is the agitator is out! Needs replaced! This is complete crap! The new parts will costs over $500 bucks plus labor! Ridiculous! My last washer which was a Maytag lasted me 20 years! What a piece of junk! Now I have to. It a new washer! No thanks to you Whirlpool! I will never buy another Whirlpool appliance again! Neither will my family or friends!

I purchased Whirlpool Duet HT front-load washing machine with model #GHW9400PLO. After a year of owning the product, failure codes continued to appear. I have followed the direction under the troubleshooting page which said to cancel and unplug the unit. After doing this over and over, I finally took the top lid off to inspect the problem. A ribbon cable was torn due to the top lid rubbing against the lid and the drum. I called Whirlpool and this was not covered (go figure). I then asked for the ribbon cable and they said they cannot just supply the ribbon cable and that I would have to buy the user interface which is $191 plus a $35 core fee because they re-bill them. What a rip off. A ribbon cable from a computer store would only cost $10.00. After that repair the Micro Machine control went out which is code F11. Code F11 is all over the web because this is a defective part that Whirlpool should do a recall on but why do that when they can charge $310 plus, get this another $35 core charge because they re-bill them? If you are not mechanically inclined with these parts plus labor you could have bought 2 washing machines. But who in the world would buy 2 pieces of junk right?Bottom line is: do your research and buy from a company that will stand behind their product because Whirlpool will not! They know by the number of parts they ship out that that part should be recalled.

I bought a Cabrio washer in late 2015. All Ive had is trouble with this joke of a product. After three years it wont do any cycle, the people at Whirlpool dont care. Please dont buy any Whirlpool product.

I like my machine even though there is no agitator. It is a top loader so it does not smell. It is a water saver which, when I first got it, I thought that it could never clean the clothes in that small amt of water...but it does clean the clothes very well.

We bought the set washer/ drier from Lowes in 2008. The first problem was that it wasnt rinsing well. After finishing the washing cycle, clothes were still dripping water. It took us to make several phones calls to get the problem solved. Also, the clothes were smelling bad and needed to be wash again. Now we are having another situation that it start the wash cycle but it wont finish and shows a code F35 or sud.

Purchased a Whirlpool washer 14 months ago... however just unboxed the washer. Installed it in our new home. Now after just two, repeat, two months of use, there is water all over the hardwood floors... The front door seal is gone to the tune of $100 but what about my floors!!!!!! Im so discouraged after reading all the complaints that Im falling out of my chair. Seal design has been the same on most all their front loaders. DO NOT BUY A FRONT LOADING WHIRLPOOL WASHING MACHINE. YOU WILL BE SORRY YOU DID. Yes they look pretty. My parents old top loader washer lasted over 35 years without a repair and we washed clothes for four people.

We purchase a Whirlpool duet washing machine 4.5 years ago. Just recently the bearing went on the machine. Took the machine apart to fix and was originally told new parts will be delivered free of charge since this is a common occurrence. 5 weeks later and several phone calls, we were told the part is on back order and they do not make it anymore. Then they send an email to keep us as customers for 15% off. Ridiculous. How do you go from getting parts for free since it is a frequent occurrence to not having the parts at all and getting 15% off for a new product? Why would I want to stay with these false claims? Talk about a slap in the face!

They sold me a washer that did not work. First load failed and the machine locked closed. Error E1 F9. Took 7 days for technicians to open the machine. The laundry was rancid by then. Needed a new drain pump motor, which was installed 37 days later. Whirlpool offered $150 for my loss of clothing. Ridiculous. Value $900, I asked for $500. Awful.

I purchased a new Whirlpool Cabrio washer 3 years ago. It is the worst washer I have ever owned. During the first year it had to be repaired. It continuously flashes F51 when I try to wash a load of towels or bedding. I am beyond fed up with this machine and will NEVER purchase another Whirlpool product. If you are considering purchasing one of these I would tell you not to waste your money.

From the very beginning the washing machine did not clean the load. It doesnt even get the load completely wet. The best you can hope for is to utilize lots of fabric softeners to at the least make your clothes smell clean because they surely wont be. Dont even get me started on the load lock feature because it serves no purpose other than to drive you batty. When your 15 year old son offers to give you money to buy a new washer after owning the one you just bought there is nothing I could say more profound than that. How Whirlpool stays in business befuddles the mind.

It is a very reliable and efficient washing machine. I enjoy the energy saving features as well as how clean my laundry is, no matter how soiled they may be. I would definitely recommend a Whirlpool washing machine to a friend.

I feel the Whirlpool washer we have Works amazing. Its an older model and Im still happy with it. It does big loads without having to do it over again or on balancing itself. I have actually had a Samsung washer and we constantly had issues with it - sensor problems and was not very user-friendly at times. I also feel that a lot of the newer washers out there are cheaply made plastic parts and can break easily. Too many companies cutting Corners these days.

We purchased Whirlpool Cabrio Washer WTW5600 series in October of 2010. I bought the machine from Sears and also bought the extended warranty. Less than 6 months after I had been using it, I noticed that all my husband’s shirts were getting sweat stains under the arms and my hand towels were very smelly after drying with them one time. I called Sears to have someone come out and tell us what the problem was. He said I was using too much detergent so I reduced the amount of what I was using. It did not help the problem so I started using the extra rinse each time I washed, still did not fix the problem. I called them out 3 more times in 2011. One tech told me I was still using too much detergent so I reduced down to 1 tablespoon like he suggested. I stopped using softener in my washer because he said I needed to clean my machine more than one time a month, to clean it every 3 weeks. No solution to the problem still. I have had a tech from Sears and one from Whirlpool (who incidentally was the same man, he was from A&E Appliances). When he came in the door, my husband told him he had been here before and I said 2 times. He lied and said he had not been out before. Are we blind? No. He ran the cycle but sat in his truck while he was running it. None of the techs have ever put a tool on the machine to check if the water level is right. They just stand there and tell us to change the amount of detergent or clean the machine with Clorox more often. I cleaned it 8 days in a row and the clothes still smell and still do not get cleaned. We talked to main man at Whirlpool and said they couldnt do anything because their 1 year warranty had run out. We have been using Whirlpool appliances for over 30 years but I will not ever buy another one. I have probably had 5 Whirlpool washers over the years but never had a problem until we got this Cabrio top loader without an agitator. I would not recommend this washer to my worst enemy, if I had one.

I had a Whirlpool washer that was 31 years old so when the motor went out I bought a Whilpool Cabrio. I HATE it!!! First, it takes at least an hour for 1 small load to finish. Then the clothes are not even clean and rinsed all the way. Dry patches on clothes and where the soap did reach the clothes there is white soap scum all over. I tried using the extra rinse function and still soap everywhere. Im hardly using any soap to begin with. I have to wash some things twice to get the soap off. Thought I was doing good by buying HE. What a waste of money. I cant wait til it breaks which should be soon according to all the previous comments. I have only had it 4 weeks. Dont buy this machine!

Whirlpool Cabrio washing machine - We purchased the (best name brand) from Get It Now and all we ever had was problems. We will fill the washer 1/2 full of clothes and the clothes on top would not even get wet. So we have to do it again, to make sure the rest of the clothes were washed. Many times there was white smudge marks on the clothes, sorta like powder (we use only liquid soap that you recommend). Today I washed a child’s bedspread for the 4th time because the stains would not come out (from a cookie). I had to turn the bedspread twice just to get it wet. I used bulk load and heavy duty load and it doesnt work. Your product is a very big disappointment for the price a person has to pay. I will recommend that no one purchase this product. Your people need to do further research on who this machine cleans clothes.

This washer is going back. It simply will not spin the water out of the clothes. It says it gets clothes drier than a conventional washer, but I have not found that to be true. I have to use the drain/spin cycle over and over and still the clothes are wet. I had the repair crew out and they were able to get it to spin out a very small load consisting of two sheets and two towels. Other than that, it does not spin out water. It is also very difficult to load if you attempt to leave the center open as they recommend. The cycles are very long. Not being able to look inside without pausing it and waiting for it to unlock is also a huge hassle. I am getting one with a glass top so I can see what is going on. If you leave it open for too long, it cancels the cycle and drains all the water, and you have to start over which is another problem because all your detergent just got drained out before the load gets going. It uses so little water on most of the cycles that the clothes get totally tangled up with one another. I think you should be able to choose the water level manually. I am all for saving water but if I want more water from time to time, this does not allow you to do that. I DO NOT RECOMMEND!

Model CAE2745FQ0, Serial #C72680766 - Purchased this coin op clothes washer 2/2/2018 at Brandsmart, Deerfield Beach FL. Would not empty or spin correctly; 1st service call 2/28/2018. (Less than 30 days from purchase date). 3/21/2018 called Whirlpool again as same problem continues (as listed above). Washer is not being overloaded. Whirlpool repair visit scheduled again for 3/23/2018. This is the 2nd repair time since we purchased the washer on 2/28/2018. Purchased the same model 2 years ago, and experienced repeated problems to the point where we got rid of that machine and purchased the most current model referenced here. We are looking for a full refund of the purchase price as it appears that this recently purchased machine is on its way to be a repeat performance of the 1st machine that we got rid of (that was purchased 2 years ago). Again, we want the full purchase price refunded, which is $900.88. This machine is not even 2 months old. Thank you.

Buyer beware! I purchased a Whirlpool Cabrico topload and with my second wash, I realized I had a mess of a new washer. Ive called the call center on 3 separate occasions and I have spoken to other customers who have the sample complaint. The clothes are not washed clean. They have a residue left on them. My advice to all potential buyers, dont even consider buying a Whirlpool Cabrio washer. It is the worst purchase I ever made in an appliance. Im very unhappy with my washer.

I made the mistake of buying a whirlpool product and was wondering if there is a support group for angry unsatisfied customers? I have owned a duet washer and after 2.5 years is giving F1E2 error and is junk.

I have been complaining since 2 months after I bought the Whirlpool Cabrio washer. It is the most expensive piece of junk I have ever bought. There is never enough water to thoroughly wash clothes. The clothes always tangle up. The UL comes on all the time because it is unleveled and clothes were so knotted up that I can’t get them out of the washing machine. I keep calling and complaining, but all I get from Whirlpool is that I need to sort my clothes better and not wash all pants together because the legs will get tangled. So, do I wash some of my dark paints with towels just to keep them from tangling up? I don’t think so. I paid $750.00 for this piece of **. It should wash a mink coat for that price. I keep checking websites in hopes that there is a recall on this thing. For sure, though, I will never buy another Whirlpool product after this purchase.

Purchased this beautiful sleek Cabrio washer in May 2012 from Appliance Smart, with its modern looking glass top, it looked so nice. The washer itself works ok for now, but it does unbalance a lot, thats not main issue. We deal with that. The poor design of holding that sleek glass top in is the problem. After a little over two years, it started cracking at the hinge that is just mounted in Plastic which holds the whole lid down, including the heavy glass. The glass started raising up, causing steam to escape. The lid is rubbing and very difficult to open. Appliance Smart is gone now.. We called the service repair person about 6 months ago, he looked at it, said its a problem that is not covered on our warranty and it would be approx $350.00 to repair!! So today, tomorrow or next week it will stop working because the lid is popping off! Its a terrible design, dont be fooled by its sleek look. The manufacturer takes no responsibility for this major design flaw. Beware, the very thing you need to be fixed wont be covered under warranty, lemon law, or just good customer service. We have owned several Whirlpool appliances and doubt that we will own one again, due to the way this issue was handled by Whirlpool.

Top loading Washing Machine Model #WTW4950XW2 - You would think that a big company like Whirlpool would make quality washers. NOT! Our top loading washer bought in late 2011 has been making loud noise during the washing cycle for the last 6 months, and last night was struggling to spin. Seriously, with just my wife and myself using the washer once a week, this washer should last over a decade! So I called Whirlpool and explained the problem... and, as expected, they cannot help me as it is over the one year warranty. NO MORE WHIRLPOOL BRANDS FOR US!

I think the whirlpool washer is a very nice machine. I think it does a good job of cleaning but still has the tub odor problem that a lot of front load machines have. As far as reliability it has done pretty well but I did have to replace the tub bellow and it is only 5 years old. It also makes a lot of noise so it is not a quiet machine at all. The steam option on the washer is a nice feature but not sure how much it does to help clean stuff.

This is the worst washer ever. I purchased this washer (Whirlpool Cabrio Washer Top load) brand new in the box thinking it was a great price and a good deal. Worst choice ever. I have been so disappointed in this product. It is very noisy which is something I have learned to live with. It doesnt even get simple stains out. I have tried every load combination and change detergents and stain remover a couple of times. Most time I have to soak stains again and again and then wash several times and most times it simply doesnt clean clothes. It leaves detergent residue on dark clothes so of course I end up washing those again as well. The towels and sheets turn into mushrooms in the bottom of washer.

I have owned a Whirlpool Cabrio HE WTW6400SW3 for two years and have had nothing but issues from the start. Control panel was replaced twice under warranty. Also the clothes (socks underwear) were under the tub blocking the drain. This is not covered under the warranty. I was told by the repairman that this is the usual issue. He told me they took the front loader design and just stood it up with no protection from garments and coins getting under the tub, through the under tub filter often and into the drain pump. You are kidding me? Almost $1000 for this washer and its so ill designed. I have read forums that this has been an ongoing issue for several years yet Whirlpool continues to build these. I dont vent to forums often but just now I finished removing the tub to remove 2 socks and 7 cents. Also, I had to remove the drain pump and found another 16 cents inside it. So far the pump has not been ruined but this time water is coming out from the machine so will probably be ordering another pump for it as well. The wife wants it out of the house tomorrow and not another cent spent on it. But it is only two years old. What do you do? If you are reading this because you are searching for a new washer do not purchase a Whirlpool! I have gotten nothing but grief and was put off by their customer service dept as well. I guess after fielding so many calls about the same thing they have been told to just put all the calls off as no big deal. I am sure Whirlpool is making a killing off the sales on this unit. The claims made during the sale convinced me. What a joke. Look around the internet and you will find hundreds if not thousands of the same issues.

We purchased a Whirlpool Cabrio model # WTW6400SW3 in 04/08. Approx. 6 months ago, the washer started to be un-level during the spin cycle. This has progressively become worse, it now becomes un-level during the rinse cycle. We spoke with the appliance store where we purchased it, ;hey said the repairs could cost $400 or more. Thats nearly half of what it cost new. Like other complaints Ive read, cheaper washers have lasted years longer than the Whirlpool. Our last washer, a Kenmore, lasted 15 years.

The washing machine is making inviolable noise. I had purchase a semi-auto Whirlpool washing machine from Lotus Koh-e-fiza, Bhopal two months ago. Initially, the company sent a man for demonstration, and at that time, the machine was making a sound and the mechanic removed his back plate and his components and saw that the plate of heating rod is unscrewed. He temporarily tightened that plate with normal screw, and after two months, the same sound is coming again.At present, we are not using the product for the past 5 days and launched a complaint to customer care. The call attender said that the problem will be solved in 20 hours but no one came within 4 days. Today, 21 September 2011, I called to customer care. He was telling me that the complaint has been attended by our attender and at present, no complaint is pending. The washing machine is in warranty period and I am not satisfied with the service of Whirlpool. At present, I am using the product of Godrej and LG, and the service of both company is very good then Whirlpool.

I hadnt had the machine. In no time, I started noticing brown rust looking spots on my whites and light colored clothing. I got to looking and had rusted out all around the bleach dispenser, entire area on the entire top. I was told to replace it. This would be about $200. Ridiculous!

Design is made so you will need a repair man to clean filter. The machine has to be taken apart to get to filter. About one hour of your time. If youre not handy its a paid repair About $250 to $300. Also the valves that control the water into the washer failed after about 5 years. An easy fix part costs about $60. All appliances are designed to fail after the purchased extended warranty expires. More features more repairs. So if you arent going to use a feature get a simpler machine. More money does not mean better machine. Or that it will last longer. The days of an appliance lasting 10 to 20 years are over.

This washer is 5 years old and the top is rusting out on the inner rim. I have city water that has been tested and found to be totally safe to use and drink. Neighbors using the same water and owning different brand washers have no rust problems. Does anyone else have the same problem with their Cabrio washer?

Purchased my Whirlpool Duet front load washer WFW9150WW00 new in 2010. Also purchased extended warranty. After four years, just before my extended warranty was up, the entire inside needed replacing (drums, bearings). Now at only five years old, it keeps making a beeping noise in middle of wash cycle and wont continue working. Serviceman was told by a Whirlpool tech. that it could be two things, one being the door jamb, the other being the control panel. Door jamb was fine. Ordered new control panel ($240), had it installed and yet the washing machine still keeps beeping and doing the same thing. The serviceman doesnt know what else it could be. So, I am forced to return the part and purchase a new washing machine. I would never recommend Whirlpool to anyone!

I purchased a washing machine FS65 on 10-30-2005. In Oct. 2009, my washing machine developed some fault so I contacted the Whirlpool service center and got it repaired. Again in Dec. 2010, the appliance became faulty and so I contacted the service engineer to attend to the machine. He repaired it and I paid 2500/-. But the very next day, my appliance showed the faults again. It was rectified with replacement of PCB and I was charged 2786/- on 01-20-2011. Again on 09-04-2011, the machine became defective. On the call to service center on 09-05-2011 and attended by engineer on 09-06-2011, I was informed that PCB is defective. I failed to understand that the PCB replaced in January was of what quality that it has to be replaced now after such a short span of time. I feel that this is clear cheating with me.

I purchased this machine three years ago. It is junk. I have had two washing machines and they lasted for years and years. Never had a problem with either machine. I purchased them from Sears. When I the Cabrio, I was told it was the top of the line washer for Whirlpool. Three weeks ago it started making a noise like a plane taking off. It wouldnt spin the clothes. The repair person said that it could be three different things the parts, for which, would cost in the vicinity of $200. However, since it was making such a loud noise and water was coming out from underneath the washer, he was certain the transmission was out. He said the noise was an indicator the bearings were gone. I didnt see much point in repairing the washer if the transmission was out because it couldnt be fix.There was a couple at Lowes purchasing a machine at the same time as myself. They said they had a Cabrio also and it was only two years old. It wasnt spinning the clothes either and making a tremendously loud noise. They told us this before we mentioned that we had a Cabrio also. I will neither purchase another Whirlpool product. Junk!

Cabrio - In Dec 2013: Ran the Clean washer cycle and it would not cut off. I had to shut off manually. Called the company and they sent a technician, who said he fixed it and that everything was good. Fast forward to Feb 2015: Tried cleaning the washer again. When I left the house there were 10 minutes left in the cycle. When I arrived home 7 hrs later, the washer was still running and my hot water heater had cut off. I had to reset via the circuit breaker. This will be my last Whirlpool appliance for a long while.

I just bought a Whirlpool Duet Front Loader, and it vibrates excessively and wont fully rinse out all of the detergent. I have to take the tray out each time and rinse. Also, it has a musty smell.Whirlpool sent a repairman out to replace the shocks on a washer that is less than 2 months old. The repairman told me to use less detergent, but I am only using a teaspoon of powder detergent which is recommended and using Affresh once a month. There is nothing they can do about it till it is deemed unrepairable.

The unit I live in is at **. They purchased it in Nov 2011. The washing machine worked for 2 months. Now, it has to be dismantled at my home and take a day off. I would like a replacement. The Dutchgate is still being developed. They purchased at least 60 at this point, there is no reason not to give me a new one instead of having two techs dismantle the machine in my new home for 4 hours and a day off of work. Model WFC7500VWl, serial CD13528709. Please try to assist me.

I bought a Whirlpool front loading washing machine 5 years ago, which has given me constant trouble. The computer on the machine is not working. When it is fixed, the machines makes extremely loud grinding noises and frequently the spinner does not work properly, leaving you with heavy sodden wet clothes. Whirlpools guarantee is very limited and customer service is unhelpful except to apologize for your horrible experience. You will have to pay for a technician to diagnose the problem. I will have to replace this costly machine after just 5 years of unreliable service. I would never buy a Whirlpool product again.

My Whirlpool Cabrio has been a real workhorse of a machine. It has been able to take large loads and small loads and get them equally clean and fresh. This was a more expensive model but it was worth the purchase price as I have used the various features provided. I also have appreciated that if you leave clothes on the washer overnight they are still fresh in the morning.

I have a 1 year old Whirlpool washing machine (Model: WFW94HEXSW Serial:C04151969). The grease from the drum is found to be the cause of clothes being ruined during the wash cycle. I waited over 3 months for a replacement. The drum arrived broken. I ordered again, and it was then said to be on back order. The water shut off developed a slow leak, causing the water to fill, and flow out the front door, causing carpet damage. We have been forced to throw away good clothes, and pay to have our clothes washed, at a not so local laundromat. We feel it would be more than reasonable to have our washer replaced, and professionally installed immediately.

I purchased a Whirlpool Duet washer from a local appliance store in May 2009. I also purchased a 60-month extended warranty covering the washer until May 2015. I was shocked when I tried to use the washer today (May 16, 2012) and it would not turn on. I called the repair facility the appliance store supplied as the warranty repair facility, only to be shocked again. I was told the appliance store suddenly went out of business and my ($130) extended warranty was no longer in effect and I would have to pay for repair out of my pocket. I then called Whirlpool knowing they would stand behind their faulty $740, 3-year old washer. They told me there was nothing they could do because the one year warranty they offered was over. I had a repair person look at the washer and he told me a control board had to be replaced and the repair would cost at least $550. I told him I was just going to buy a new washer. I had not been happy with the washer from day one and was very sorry I had purchased it. It did not wash the clothes very well. Also, I had a musty/moldy smell in my basement that would not go away no matter how much I cleaned. The repairman told me today that the smell is coming from the washer. I just cant believe I am out almost $1,000 and there is nothing I can do about it. After reading the many reviews on this website about Whirlpool appliances, I am sure they will not be in business much longer. They should be ashamed of themselves for what they are doing to consumers like myself especially in todays economy. Is there anything that can be done about this?

I purchased my Cabrio Whirlpool washer 4 years ago and have had problems every since I bought it! Thank goodness I bought the extended warranty! The last two repair bills were over $1000 each! My warranty just ran out and I had it repaired last two months ago! This is not my first complaint! When will they start listening to consumers? This is ridiculous! Now I am faced with the problem of just trashing this washer or spending another $1000 to repair it! Something needs to be done! I am warning all of my friends and family and will post again my problems with this washer on all my social networking sights! Whirlpool needs to take responsibility for their problems! I will never purchase any Whirlpool products ever again if they do not assume responsibility!

How I wish I had read this board before purchasing! This is the worst washing machine made. Put your clothes in the sink, add water to cover two thirds, add detergent, slosh around slowly for a few minutes, wring and remove. You have replicated a Cabrio wash! I have complained repeatedly, had a repairman who assured me it was working properly (as designed, too little water, too little agitation). I was a lifetime Whirlpool client.

Ive trusted Whirlpool washers for 20 yrs. Ive only had to buy 2 in my lifetime and neither have let me down. I will always purchase Whirlpool as it is a brand I can trust. Features and reliability are important to my family. Whirlpool has it all!

On October 29, 2009, we bought a new Whirlpool 30 gallon gas hot water heater to replace a Rheem we had for 20 years. We immediately had problems with the relief valve leaking, so we ran at the local hardware store and bought another valve. Next, we had trouble lighting it (husband was a plumber years ago) but a call to the hotline and we were in business. Now just over 3 years later, the pilot light started to cut off at will. Troubleshooting solved nothing. We called the hotline again and were given a part number, an authorization number and told to go back to Lowes for a replacement part. Figuring how our luck runs, I called first and was told there was no such part number. Trip saved. Now after reading all of these reviews, we have decided to cut our losses and buy another Rheem. You can find the Whirlpool hot water heater sitting beside our 2-year-old Kenmore HE washing machine (also made by Whirlpool) on the garbage pile. No more Whirlpool!

I purchased a Whirlpool Duet HE front end loading washing machine. Less than two years after purchase, the machines tub and bearings failed amounting to a repair bill of $1035.00. Fortunately for me, or so I thought, I purchased an extended warranty for the machine. However, even though the complaint department was aware of the failure, the amount of the repair and the fact that I declined repair and was opting for the $500 reimbursement option, I was told that the claim, as it was called, would take 2-3 business days to process and if I was awarded (his words) the reimbursement, I could only use this money on a new machine at a Sears store and not on any new, but previous year model, or at a Sears outlet. None of these things were related to me when they took my $214.00 for the warranty. In all, my original washing machine of 22 months will have cost me $1414.00. My new washing machine, if awarded one, will cost approximately $400. The total cost to wash clothes for 10 months will exceed $1,800.00. Do not purchase Whirlpool front end loaders because the drum bearings will break (that is why they exclude them from extended warranties) and do not buy extended warranties as Sears makes out in the end.

Cabrio WTW8200YWO - We purchased this washer five years ago. About a year ago it started getting noisier and noisier on spin cycle. Now it sounds like a jumbo jet taking off. A Google search quickly revealed this is a ubiquitous problem with these washers. As we are in our 70s and dont have kids at home, we are very light users of the washer. First, I would suggest that no one buy this washer. Second, I suggest that Whirlpool should recall these washers. I called Whirlpool and it turns out they clearly know about this issue. The good news is they will offer you a discount on repairs or even on a new machine. The bad news is it will still cost you several hundred dollars to fix their design defect. I suggest that you avoid purchasing Whirlpool products both because of their defective design and because of Whirlpools unwillingness to take responsibility for these problems.

After only 3 years using my Whirlpool front loading washing machine the inner tub is already broken. The repairman said the cost is just about the same as getting a new washer. After reading all the horrible reviews on the Whirlpool washer I WILL NOT be getting a Whirlpool. I am so disappointed in the washer and do not recommend it to anybody. Do not buy a Whirlpool appliance ever.

In the first year of my Whirlpool Washing Machine, the motor quit working entirely. Fortunately, the machine was under a 1-year warranty and the motor was replaced by a Whirlpool service technician. My big complaint with this washing machine is this: Even though you select hot water for the wash cycle, the machine has sensors in it that only allow the water to get lukewarm. If it senses the water getting too hot, it adds cold water to bring the wash temperature back down to 78 degrees F. Next time I will do my research and buy a machine that actually allows one to use hot water.

Horrible. We purchased the set In October 2010. It worked great for a little over a year. (Go figure, just out of the manufacturers warranty.) The washer stopped spinning out water. Every other cycle completes successfully. The diagnostic cycle is also successful but once there is clothes in the machine, it wont spin. I called customer service and was told that a one year warranty was $230 and service is $130 plus parts. After reading another horror story, it seems that this venture is going to cost us around $450 for a new circuit board. Where is that class action suit at again?

Special features eg changing HE detergent conc. ratio for auto add feature in Load and Go is impossible to find, extra rinse doesnt work. No extra spin which would be useful for bulky loads. But preset cycles work fine and machine has very low vibration a big plus.

I had a Whirlpool washer for three years that I bought at Sears and it started making a noise. I called Sears repair and they said it was the bearings. Would cost 600.00 dollars. The machine is still running making a noise are there more in a machine. I will never buy a Whirlpool product. I just lost my husband and I cannot find the bill but I am calling Sears tomorrow.

I purchased this washer brand new just 2 years ago. It started making loud crackling noises approximately 3 mos ago. Yesterday it decided it did not want to spin or drain. Today a repairmen tells me its a wash. The computer screen has gone wacky and the cost to replace that will be well over $400, almost to the penny what I spent 2 years ago. This is not a good product Whirlpool and i trusted you since my previous washer lasted over 15 years. I need a refund and a new washer! Disgusted!

We bought this washing machine in 2013 from Plass, an appliance store in Chicago that is now out of business. The top loading plastic lid that holds the glass piece snapped and broke. I called the company, and they said that there is not a recall but that I could order parts. They put me on hold, and 10 minutes later, I was on the phone with a company in Missouri that wanted to sell me a lid for $219.38 plus tax and shipping. I am surprised to see that others are having the same problem and that there are no recalls from Whirlpool!

After much frustration and disappointment, as well as 2 huge repair bills with my front loading washing machine I sent it off to the scrap yard, still looking brand new, and went back to a top loading machine. I purchased a Whirlpool top loading, high efficiency, low water machine. I have had it for almost 2 years now and am extremely happy with it. I would highly recommend it. Fairly quiet and easy to use and takes very little detergent. It does not have an agitator so it is gentle on clothes. I know some users have complained about tangled clothes but, in my opinion, if it is loaded correctly this should not be a problem.

In 2008 bought cheaper Whirlpool washer, had to return it to Lowes. ELLL DUMOH (me) buys yet another Whirlpool Washer from Lowes; a Cabrio. The Cabrio ONLY worked 3 years, and started having problems with not emptying or just continuing to drain and beep. The Whirlpool Customer Service lady is pitiful. Yeah... I can SELL you another set of shock absorbers... that might help. I can SELL you a recirculating pump or a drain pump... Pitiful, sorry attitude. Goodbye Whirlpool.

We purchased a Whirlpool front loading washer about three years ago. During our first year the machine worked OK, but three months after warranty expiration (12 month warranty), the sensors seems to go wonky and it no longer worked (at 15 months of age). We paid about $95 in the Minneapolis area for a service call. The repairman had to call Whirlpool from our home to inquire about the sequence of flashing lights on the sensor. After getting off the phone he told us he thought he knew the problem, but could not guarantee that the $200+ part he suggested ordering would solve the problem. The installation would require additional labor charges, of course. I reported the incident to the manager of the repair service and was told the repairman was expert in Whirlpools but this did not further inspire confidence. We were not willing to sink this amount into the machine, so ditched it and bought a top-loading inexpensive Roeper. The top-loading machine definitely appears harder on the clothes than the front loading Whirlpool, but it gets the clothes cleaner and has been problem-free so far.

I have a front load washer by Whirlpool and a motor stopped working on the drain. When I called them, they told me it would be $200.00 for the part. I dont understand why they dont stand behind there product. What can be done to make these people fix there stuff? This is there product, if they cant do it right, then find a new job!

I bought this washing machine after having my Kenmore for 20 years. This washing machine is a nightmare. I have to wash my clothes 2 or 3 times, to get them clean. Everything has residue on them. Once a month, I do use a cleaning tablet, and between loads, I wipe the washer out too! This is the biggest piece of junk! Save your money. Buy an old school washing machine.

Purchased a house and old owners left an almost new one with house. Thing does not clean even minor soiled cloths. Plan on buying new machine directly and it will not be a GE or Whirlpool. I can see why they were willing to leave the new washer. I left a 15-year old Maytag at my old residence (wish I had it back).

Whirlpool Duet - they are highly rated and are aesthetically pleasing. Highly rated, they are expensive, my last Duet w/d didnt last as long as expected. Ive had to repair both machines once since I purchased them. Good quality is of utmost importance, plenty of washing and drying options, front loading washing machine, full size extra large capacity, attractive machines, good reputation for quality and lack of repairs.

Purchased top loading Whirlpool Washer WTW5000DW0 10/12/2015 at Best Buys, first no agitator machine for us. Two weeks later I call for repair service because of the noise from tub. Explained in other reviews as earthquake or jet engines. The machine is in the garage and can be heard through the walls into the house. Repair tells this is normal for the machine and it must be our first none agitator machine.I then purchased a extended warranty policy through Whirlpool. 12/13/2016 machine no longer washing clothes. Call Whirlpool for service. Repair came out 01/17/2017 (a month later). Washer plate had to be replaced. The gear was completely shredded. Not in stock, waited 2 weeks to get repaired. Tension springs on outer tub replaced at same time. Was told the excessive grinding and bumping of the tub was not the reason for the gear shredding.06/30/2017 same problem, I set a repair date 07/01/2017 between 8:00 a.m. and 12:00 p.m. No one shows and no call. I call Whirlpool and they are sorry and set the appointment the same day for before 5:00 p.m. No one shows our calls. I call back. Already closed. I call the next day. Sets a new date 07/05/2017, 8:00 a.m. to 12:00 p.m. Same problem. I called back speak to a supervisor who says hell get to problem and find out whats wrong. Sets a new date 07/08/2017 8:00 to 12:00 p.m. 07/07/2017 I get a call after 5:00 p.m. that the repairman is not available and can we reset for 07/13/2017. I hung up and called back the next day and spoke to a supervisor I had previously spoke with. He called an outside repair company that Whirlpool uses in this area. New date 07/12/2017. Repairman shows and I explain the washer plate was loose again and I smelled metal burning. I had told my wife to continue to use the machine to wash the clothes. The repairman tells me I voided the warranty by doing this. Im standing in the garage while he has his head in the machine trying to get the washer plate out. He shuts the lid and turns the machine on wash/spin says the machine is ok. We have an exchange of words and tell him I want to see the washer plate gears. He says he cant get the plate out now and I wasnt there for him to show it to me. This continued until he forced the plate off. He called Tech Support to say I voided the warranty. He told them customer claims loud noises and banging. I asked to speak to Tech but he tells me they dont speak with the customer. I looked at the gears on the washer plate and the transmission. Both had metal shavings. He tells me he is going to do me a favor and replace both. Its supposed to take a week. Wait and see. I have asked for a replacement or money for the machine through Whirlpool. I was told there has to be at least 4 repair requests for the same problem and the repairman has to determine that there is a problem or that its a lemon. I will not recommend or purchase another Whirlpool product.

I bought a new washer thinking I was upgrading. Wrong!! Well the new so called technology they put into these machines is overrated. They took a good thing and instead of advancing they have took two step backwards in time. I wish I had kept the old washer I had. I think I would rather use an old time wringer washer my great grandmother used. They are probably faster by hand. This new Whirlpool grabs every string on my hoodies and twist my clothes so tight in knots. I cant even remove my clothes until I fight and get mad enough to write a review. Whats up with these new washers?? Get rid of the slots on the Agitator!!

I have always chosen Whirlpool or a Whirlpool product such as Kenmore or KitchenAid. Preferably with an actual agitator in the tub. As a very capable handyman, repairs have been easy and relatively reasonable in cost. My units are 15 years old and going strong.

I purchased the Whirlpool Cabrio Washer thinking I was purchasing a quality product. Unfortunately it was one of the worst decision my wife and I have made. The bearings (lower) only last about 2 years. We purchased the extended warranty and the first time it was covered. The second set were not covered and now we will have to change them again. We will not ever purchase another Whirlpool product. I contacted them several times with no positive results. I still saved the last worn out bearings to show the CEO. The engineers do not have a very good idea to make the lower bearing last. Where I purchased the machine they told me after the first change that it would happen again and they were correct. If anyone needs to contact me about this product feel free. NEVER EVER BUY A WHIRLPOOL PRODUCT.

Whirlpool Cambridge Model #WTW7300DW0 - Someone needs to help us consumers with this wash machine purchase being refund our money back from Whirlpool. It literally eats my clothes. I have 23 shirts that have pin holes in them and 1 shirt with large holes in it. I also have a ruined comforter and blanket. The comforter has soap stains everywhere which dont come out so its not cleaning the clothes, the blanket (which Ive had for over 30 years) was frayed one side, seam torn off - the piece never came out of the wash machine. I have pictures attached of the damaged. Its suppose to be Water Efficient - thats a joke! I do 1 set of king sheets. It runs for an hour and 20 minutes and fills water to the rim of the washer and does this twice. Id like them to pay for my water bills! Oh they came to service it only to tell me I was putting the clothes in wrong. The service company said I had to put the clothes against the sides and leave the middle open. They told me there was nothing wrong but consumer error. Well I did clothes today and aligned them like the service company said - 4 more shirts were ruined. Called Whirlpool today. They said they were sending someone else out to fix the problem and said, Unfortunately, we dont pay for damaged goods. Well from all the reviews I read Whirlpool needs to suck it up and recall this piece of crap they call a wash machine. Did I mention its only 1 year old, yea this is horrible!

I HATE this washer!!! Did I say hate this washer? YES. Do not buy it. Delicate cycle. Ha ha ha. NO!!! Good thing Im retired because I need to check it every 5 min to see if its getting clothes wet or untangle a mess. I find I use the rinse and spin cycle once with a little soap and run it again to rinse. A lot of extra work. Sheets washed in the deep water cycle turn into a giant twisted mess if you dont stop machine and untangle everything. Hate it. Hate it. Do not buy this machine. I use more water by washing things twice or fewer items. What a waste of time!!! Locking lids are the worst thing ever designed. Why?? Dont tell me some stupid kid is going to climb in it. We should have a choice or be able to disable it!!! Worst machine ever designed???

We are so disappointed in the purchase of this machine! It doesnt put enough water in the machine to clean the clothes, and the spin cycle has continuously gotten louder and louder to the point I think its going to explode when it spins! Is there any recourse we have or any recalls on this machine?? Thank you for your help!!!

Had washer since 2016. Have NEVER washed a load where there was not a problem from washer dancing to having clothes come out without water ever touching them. Would NEVER recommend Whirlpool! Tried to contact Whirlpool website to register a rating & even their website is defective - could not get through after several attempts.