This machine cannot handle washing jeans, towels, blankets, pillows or anything bulky or very small loads. The load becomes ul unbalanced almost every time I try to wash a load. It has never gotten things very clean.

I have purchased a Whirlpool Washing Machine Mode W/P WM ROY 6212SD(31089) Sl.No.INF 153400517) GRAY/CHR TN 6.5 on 05.12.2015 with two years warranty on complete washing machine. The warranty period over on 04.12.2017. Exactly after over 3 months the machine start giving noise and we had been in touch Whirlpool and registered the complaint during last week of March 2018 and their local service center people visited, charged Rs.500/- service charge and informed that the machine to be taken to their service center to ascertain the complaint. After over a week informed that the machine complaints of Tub Support, Seal, Bearing, Drive etc. and the estimate is Rs.5,900/- including transportation (hardly 6 kms). The machine cost was only Rs.16,900/- then. I am surprised to know that just after 3 months of expiration of warranty the machine went wrong and the cost or repair costs me Rs.5,900/- is very huge. I hope the concerned will examine this.

Purchased a matching set, Whirlpool Cabrio Platinum Washing Machine and Dryer in November of 2012. After just over 2 years, Im stuck replacing the Washing Machine at my expense! The washing machine began leaking water out of the bottom of the unit and became extremely loud when operating it. The repair technician said it was a seal and bearing that needed replaced and the cost of repairing the unit would be cost prohibitive versus replacing the unit all together ($800+)! Originally paid over 2K to purchase these units and have them installed. I do not want to trust or rely on the Whirlpool brand again. I would appreciate any recommendation for a better quality, high capacity, HE washing machine brand to replace the Whirlpool unit with (Samsung, GE, LG)??

We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age.

We purchased a 4.8 Cu FT High Efficiency Front Load Washer in February of 2016. What a nightmare. Just a few months after having it, we kept getting an E3 error message that would not go away. After 2 weeks of waiting before a tech could come out there replaced a door mechanism said it would be fine. After the next wash same thing, same problem. Could not even open the door to get my laundry out. Again they could not get a tech out for at least 2 weeks so Im stuck with the cost of getting my laundry done elsewhere. This time it was the motherboard. Had to wait a week for that to be shipped out. This was all completed in June 2016. We are now the beginning of September and same problem. Again we are told at least 1-2 weeks to get a tech out. Seriously Whirlpool, we are your customer. I have a family and we need to wash our clothes. We spent $1200 on this machine only to have to take our laundry to a public laundry mat because your machine keeps breaking down. They will not replace the machine even though this is the 3rd time with the same problem. The customer service is horrible. They are not willing to help in any way to get this fixed much sooner for her or give us a new machine. This one is obviously a lemon! I will never purchase any Whirlpool appliance again and I suggest based on some of the reviews on here no one does. Next appliance I buy I will do more research for sure.

I have called Whirlpool multiple times because our washing machine model #WFW9290FW has been out of service for 5 weeks now. I have been informed that I need part #W10604640, which is on back-order and they wont give me any idea of how long it is going to take to get this part replaced. Apparently, there are 96 total people who also need this part. I find it hard to believe that a company this big would not have this part on hand and they would not have any idea how long it would take to get it replaced. I asked them to give me a new washing machine for free to replace it because of the poor service and the unreliable washing machine. They told me they could give me another washing machine at 40% off, but based on the lack of follow-up and the amount of time that has passed since my initial call, I dont want another Whirlpool product. This is the worst customer service ever.

DOES NOT MEET CONSUMER NEEDS AS PROMISED. I wish I read the reviews. Very expensive machine I purchased specifically for the large drum for large loads. The machine cannot handle large loads (if you consider one blanket large load). I have to unplug the machine mid wash, as the load gets stuck on one side and moves my machine across the floor. The noise in the spin cycle with even small amount of laundry sounds like a helicopter is about to land. Then last night I noticed black oil splattered all over my floor. This is a $800.00 machine. Never ever met my exceptions as the machine promised to deliver. Theres very little water that enters the drum... Not even my towels come out clean. DO NOT BUY WHIRLPOOL... EVER EVER EVER.

Bought this machine June 23, 2016. First use, I called Lowes where I purchased it to say there is something wrong as it makes a grinding noise. I was informed that is normal for agitatorless machines. I asked if he could hear the noise, and he said yes, thats it. So I disconnected thinking, Wow, who makes a machine in todays technology that is so loud you think something or someone is in serious pain?! Now am at the point where I want this design in pain out of my house! Going to Lowes today to try and talk rationally for a complete refund so I can purchase an LG or Samsung which is what I should have done originally.

I bought a whirlpool washer from Whirlpool on February 27, 2011. Since then, they have come out and repaired the washer for 5 times. They have even taken the whole motor out, and replaced it. The last time they came, they said I would have to pay for the next time. Now, it has broken again, and I have to pay for a washer repair that is less than a year old. We bought the Whirlpool washer at Sears, and neither Sears, nor Whirlpool will stick by their product. We cannot afford another new washer, and to pay for repairs is a stretch too. Is there anything you can do?

This machine, like all other water sensor machines, will not let you wash a few items that are lightweight without filling the whole machine up almost all the way. The reason being is that if the items are light, they will float in the water above the water level and the sensor thinks it needs to put more water in and even with putting something in to weigh it down like a wet towel doesnt always work, nor should you have to do this. You will waste more water in the long run if you only have a few items to wash, ie baby clothes, underwear, rags, etc. I am so disappointed that I had no other choice but to get this machine.

Had washer less than 1 year and washer stopped and was flashing code F 51. Called Whirlpool and they sent a repair person. He worked on it and didnt fix problem. Called Whirlpool back. They had to order parts. Repairman came back - replaced parts. Now not 6 months later same thing happening. Whirlpool said we have to pay for labor to repair again. We went online after this happened the first time and saw where others had same problem - this washer should be recalled. The repairman said this part was corroding. This should not be happening on a new washer. We will never buy another Whirlpool product again!!!! Im concerned that it will keep repeating over and over and we paid 700+ for this washer not 1 1/2 ago. My last washer lasted 15 years!!! Wasnt a Whirlpool!!!

Front-loading does not do good job of rinsing. The Whirlpool Duet will not last longer than 2 years. Whirlpool recommends that owners purchase a new washer every 2 years. Whirlpool suggests owners purchase new clothes each week to avoid washing. Any owner would be required to quit their job in order to wash clothes. The Whirlpool Duet front-loader requires 12 hours per load. This means that only 2 loads can be washed in a 24-hour period. Each load requires 10 rinse cycles to remove suds.

Bought a Whirlpool Cabrio. Noticed it was getting really loud less than a year into owning it. Called while it was under warranty. The tech said it was fine. Within the next year and a half it got so loud, you cant hear anything else in the house while it is running. Now it is leaking from the tub seals and the bearings are going out according to two service techs I have had come look at it. They say it is more expensive to fix than the washer is even worth. This is due to the parts that would be used to fix it are the same cheap Whirlpool parts that were put in it in the first place. They both said that these are not good washers and commonly go out about a year and half to three years old. Shame on Whirlpool for making such a low quality product and not being willing to do anything about it.

Tried to do a small 2x3 bathroom rug and the spin was thrown off kilter. I have been doing laundry a long time and I know how to evenly distribute clothes etc so the washer should be able to handle it for the price I paid. The high end front loading Whirlpool set.

Im so disappointed with this product. Its only a couple of years old, which seems fairly new as my old washer was over 20 years old when I finally got rid of it because of the noise it was making! First, the Cabrio stopped draining and spinning, even though the display showed that the cycle was done. Phoned Whirlpool, and the best they could do was send out a repairman - at our cost, of course! We refused, and kept using the machine - put it on for an extra drain and spin. Then, it stopped working completely! My husband hauled it out to a repair shop and was told it needs a new motherboard at a cost of $400 plus labor! This was an expensive washing machine, and I feel Whirlpool should offer its customers better service! I guess we need to buy a new machine - definitely not Whirlpool!!

I purchased the Cabrio washer during the black Friday sale. The washer was a pretty slate gray. I loved the color and the fact it was a Whirlpool, which I thought meant quality. It was expensive but we were updating our appliances as our 10 year plus washer needed replacing. Big mistake. This washer is terrible. It keeps me stressed. There is not enough water to clean the clothes, my husbands white underwear is always dingy and dirty looking. The sheets are dirty and smells. I try putting bleach on whites before washing and the whites still come out with underarm stains. I tried all the recommendations to no avail. This machine is awful. This was a big financial mistake. As soon as I am able this machine is gone. Will go back to the agitator in the middle, and NOT a Whirlpool. I DO NOT recommend this machine unless you want something pretty because this is NOT a washing machine.

Every time I wash clothes, I get a terrible odor that permeates my home. Ive put in afresh to rid the problem. Ive had a technician take it apart to clean the filter & hose. Nothing helps!! My clothes come out smelling like the sewer. I called the company, and the person I talked to had no real solutions either. Im MAD! What are you planning to do about my stinking problem? Im washing clothes right now & have to have all doors open & fans on high!!!

Whirlpool cabrio top loader is junk from the first month. My washer has had way too many repairs. A&E repair has been a frequent at my home. Now Im getting ready to repair it again! Hub gasket or pump not sure this time. All has been replaced previously. Never ending - always something wrong with it!!!

I bought a Cabrio washer in 2009. I started receiving the infamous F51 code. When I called Whirlpool, they refused to even acknowledge that there is a problem with this washer. When I brought up the pages and pages of complaints about it, they acted like they did not exist. I hope this review will deter people from purchasing one of these faulty products!

My washing machine is just over a year old and it has ruined so many clothes... They come out with brown stains on them... Almost like a oily stain. Not sure where its coming from but its either Im gonna have to buy a different machine or keep buying clothes. My husbands t-shirts look terrible... If any suggestions to what it can be please respond back to me. Thanks. Model# wtw4815ewo. Serial# c51433710.

I bought this Whirlpool Cabrio Top Load Washing Machine in December and have hated it ever since. The energy efficiency this item claims means that you will spend a ridiculous amount of time waiting for your load to finish. My family hates this machine and I regularly have to hear about how long the load is taking because the timer adjusts continually. Put in a QUICK load and it said 38 minutes, came back in 30 and it said 24 minutes. It is so frustrating!!! We are afraid to put anything on a heavy soil setting or anything other than quick, because it can take 2-3 hours to complete. I have to schedule a day to wash my bedding and there isnt any convenience in doing a quick load. I am going to have to sell this one and purchase another washer. What a loss!! This machine has been a time and money waster! I will NEVER BUY WHIRLPOOL again!!! I bought this machine through Best Buy.

I purchased a Whirlpool Washing Machine in November, 2015 and today, I had a repair person out who said the bearing had ruptured and the washing machine cannot be repaired - 2 1/2 years later. Contacted Whirlpool Customer Service who would do nothing other than try to explain to me that I should have purchased an extended warranty as they could not stand behind the machine past the one year. Would not even offer sending a tech out on their dime to confirm what my repairman had said that this is a failed production process of these machines - it was nothing that I had done caused this issue. But yet they wanted to sell me another machine. It will be a cold day before I purchase another Whirlpool product.I was shocked at the lack of customer service to assist with a situation that both the location I purchased it from and my own repair tech said that they are seeing so often with these machines. I would never purchase another item from Whirlpool again nor would I recommend any of their items. I will go to great lengths to give others the background on how Whirlpool will not stand behind their products, lack of customer service to resolve a situation or can work outside of what is given to them to correct a situation - this is not OK!

We purchased our new Whirlpool Cabrio washer on November 1, 2013. From the start this machines performance has been a disappointment. We bought the machine at The Brick (I should have known better) where we had made several purchases over the years ( I guess Im a slow learner). Right off the hop, my wife and I noticed that the clothes were not coming out clean. Even though the machine is Eco and therefore advertises that it uses less water, there should be enough water that the clothes at least get evenly wet. That may be a problem with the agitator not seeming to have the guts required to pull the clothing down to the bottom of the drum. We went back to The Brick and told them that we were not happy with the machine they had sold us and quite predictably they told us that we should call Whirlpool (This was less than a week after we had it delivered. Did I mention that I may be a slow learner?). We called Whirlpool and they told us they would have a tech out to take a look at it on November 11th. Wow, I thought. Hows that for service. A repair guy coming out on a statutory holiday. Of course it didnt happen. When we called them back to ask if their repair guy had made it home okay, they claimed that we werent there when the repairman tried to call to confirm his arrival time at our home. We hadnt left the nest the entire day. They then told us to go back to The Brick. We went back once again and told them, yet again, that we were not satisfied. This time they agreed to send their own man over to take a look. He came over yesterday and watched the machine go through an entire wash cycle and then said that there really wasnt anything he could do, as even though it may do a crappy job of washing the clothes, it at least appeared that mechanically speaking there didnt seem to be anything wrong with it. We called Whirlpool back today and they said that there isnt anything wrong with it mechanically so from their end, at least, the story is over. What kind of customer service is that????? Maybe Whirlpool and The Brick deserve each other, but I think we should get better treatment than that

First F1 symbol on washer took 6 months to resolve. All we needed was new motherboard and couldnt mail it to us even though we could replace. It had to be an authorized person. Well we had one and they never put him in the system. Finally got that taken care of, 6 months of having to press pause and restart 5 times just to do one load. Arrrrrggggghhhh! Now water leaking out the bottom. Called again, on hold, then on hold again to be transferred to tech support. Yeah, right. No tech support. Talked to management, they could care less about us even though we have other products from them. Dont buy, they are lemons. We had ropes for 15 years and lasted through everything. Thanks Whirlpool, heres to losing a customer!!!!

Purchased new Whirlpool washer from builder - never worked. Serviced 4 times by Whirlpool - does not wash, does not sense, shakes like crazy. No resolution from Whirlpool - worst customer service experience.

We bought a Whirlpool washer in 2010. It started making a loud noise on the rinse cycle in 2012. We called Whirlpool. They sent out a repairman from A and E Repair. Was told tub bearing shot, repair over $700.00. Contacted Whirlpool, was told machine out of warranty. After talking to them, they agreed to send parts if we paid labor. Machine lasted less than a year making the same sound again. A and E sent out same thing, bearing gone. Repair cost $997.17, charged us $136.74 service call after 2 minutes to shake the drum and saying same problem. Was told by Whirlpool, no warranty, tough luck.

Purchase 2009 Duet Washer & Dryer (WFW9700VW00). Recently have had error codes coming up - F35 for one. Could not get washer to reset. Had to keep unplugging and plugging back in. Service was called and the tech knew right away what was wrong. He ordered and installed an analog pressure switch. While he was working he mentioned that this was a known error and if we had called with this problem a couple years ago Whirlpool would have replaced the washer. Im not looking for a replacement but I feel Whirlpool should cover the part having been a known issue.

Please do yourself a favor and stay away from both Whirlpool and this unit. I purchased it from a local dealership and paid $881.00 which included tax and delivery cost. In less than 2 years, it broke. Whirlpool does not offer a warranty on the unit. After having a Whirlpool repair person come out for a cost of $75.00, I was informed that the parts to replace would cost $800.00 not counting additional labor cost which was TBD. I contacted Whirlpool and went from Agent (Phylicia) to supervisor (Ashley) to Manager (Carol **). The best offer I was given was to buy the parts at a discount of $400.00 which did not include tax, delivery or labor. So it would have run approx. $550.00 to over $600.00 to fix a $771.00 washer.My next letter is to Jeff Fettig (553 Benson Rd, Benton Harbor, MI 49022/ CIO of Whirlpool) to let him know how impressed I am with his product and customer service support. The next Whirlpool item I buy will be never. Take this as a word of warning to go Maytag or any other vendor because Whirlpool will not support you once the sale has been completed. Good Luck.

The repair technician just left telling us that our Whirlpool Cabrio washing machine is fine. It is a little over a year old, makes LOUD noises as it runs, doesnt get the clothes clean and often doesnt even get them wet. The clothing sits above the water and comes out with pet hair, soap and dry spots. We use it the way the manual directs but it seems to be a totally defective machine. We sure wouldnt sell it to anyone nor give it away to some poor unsuspecting soul. Guess it needs to go to the dump. Shame on you Whirlpool for taking advantage of so many of us.

The washing machine is making inviolable noise. I had purchase a semi-auto Whirlpool washing machine from Lotus Koh-e-fiza, Bhopal two months ago. Initially, the company sent a man for demonstration, and at that time, the machine was making a sound and the mechanic removed his back plate and his components and saw that the plate of heating rod is unscrewed. He temporarily tightened that plate with normal screw, and after two months, the same sound is coming again.At present, we are not using the product for the past 5 days and launched a complaint to customer care. The call attender said that the problem will be solved in 20 hours but no one came within 4 days. Today, 21 September 2011, I called to customer care. He was telling me that the complaint has been attended by our attender and at present, no complaint is pending. The washing machine is in warranty period and I am not satisfied with the service of Whirlpool. At present, I am using the product of Godrej and LG, and the service of both company is very good then Whirlpool.

Bought this Whirlpool Cabrio washing machine 4 years ago not knowing it was a low level water washing machine. A man would have had to design this piece of crap. Not only does it not clean the clothes because the agitation on it is as slow as sloth. On top of that the clothes tie themselves in a knot when finished. If you don’t want the frustration of clothes washing, I would highly recommend you not buy this type, if you enjoy cussing then this machine is for you.

Cabrio washer - What a piece of junk! My washer is 2 years old, it now does its own thing - stopping when it wants, doesnt finish cycle, beeps finished and the clothes are so wet and the washer is not emptied. Then, I put it on drain and spin. One time, it kept going for almost an hour of off and on. My clothes were so out of shape and that was on low spin. I finally took them out and put them outside. The clothes from day one have always come out so wrinkled and that too is on low spin. Im afraid to use high spin. I know you have to for towels, but it still does not drain. It shuts off and on when it feels like it. My first contact with Whirlpool was, Well, did you buy the extended warranty? I hate it when asked that when purchasing any product. Its like saying, This is a piece of crap. Im warning you now so buy the extended. So right there, I felt Whirlpool isnt willing to help. What else can we all do here? Please advise.

Im no longer buying Whirlpool products. They do not all up and are made like crap. My Cabrio washer being the most recent problem. Hinges broke on the lid and the drum spring broke. Out the door it goes! Im having my American made Speed Queen delivered tomorrow, the last Speed Queen I owned last over 30 years.

I called customer service line regarding my Cabrio Automatic Washer (Model No: WTW6600SW2; Serial No: CU2171019) purchased on 11/24/07, to report and ask for assistance with a chronic ongoing service problem. Several calls in the past and service visits (at my cost) did not rectify the problem. Although there are many similar complaints on this machine regarding the loud noise and resulting problems during the spin cycle that involve the tub and rods, the representative said So sorry or Too bad we cannot not help you.My machine now does not run and is less than 4 years old --just like every other report. I get an error message F which the representative alluded to something involving the electronics. Machines purchased in 2004 from Whirlpool have across-the-board similar problems that Whirlpool refuses to take ownership for. This machine is their top of the line model. I dont feel the financial burden of repair or purchase of a new machine should be on the shoulders of the consumer. We bought in good faith from Whirlpool and expect Whirlpool to live up to their responsibilities. Thank you for any help you can provide.Rae **

I purchased a very expensive Cabrio top-loading washer thinking I would never have to worry because supposedly it’s the top of the line, right? Well, I have it a few years; the first week they replaced the basket because it was ruining my clothes. And then I had to replace the pump because of a coin getting caught and putting a hole in the pump. Really? What the heck? Now the basket is all shredded at the top. Obviously that isn’t right, so what do I do now? Replace the basket again? Who gives them the right to charge so much for a piece of junk? Plus, it’s supposed to save on water, but I feel that the clothes don’t really clean well. They hardly feel wet coming out of the machine.

I purchased a Whirlpool washer in 2005. After the extended warranty expired, our washer broke. The Whirlpool manufacturer did not have parts in stock. It’s on backorder, so what does that tell you? So we have had to wait for over a month for the repair shop to receive parts from Whirlpool’s manufacturer. Service is very slow and the quality of product is very poor. After five weeks and no repair parts, we are going to have to purchase a new washer since we do not have our washing machine repaired yet. I promise to never purchase a Whirlpool product again.

Purchased washer Aug 2012 and has increasingly been leaving white residue after wash cycles. Have used the Extra Rinse function to no avail and use half the recommended amount of HE Tide. Now I have to run the Rinse, Drain, Spin function twice with darks to remove the residue. I have also been doing the monthly maintenance which has not helped at all. This machine seriously detracts from the Whirlpool name and if they are unwilling to fix the problem, it only publicly displays the companys integrity.

I have a Whirlpool Cabrio washer. It was great for almost year. After that it has been nothing but trouble. The body of the washer has rust coming through the paint and large areas that is so rusted that the paint has chipped off completely. A washer is expected to deal with water and not rust through the body. I have a 10-year old Ford truck without a speck of rust. Dont they undercoat? The circuit board has had to be replaced because of rust. I have to take several Q-tips and go under the cover to remove all the rust if I dont it gets rust stains on my clothes, which is impossible to remove. The customer service is non existent. They have left me on the line for over 40 minutes. I hang on only because it would be another hour or so of my time to get someone to answer. I was without a washer for a month while waiting for parts. Why dont they have parts for their products? I had to slop my way too dirty laundry mats 3 times a week as I do 2 to 3 loads a day.My washer is downstairs and stops and gives me the unbalanced message even when its not, running up and down the stairs several times to complete one load. I also get the F51 message for no perceivable reason. The extra rinse button only works 1/2 the time. This was an expensive washer ($1,000.00) and I feel that I deserve my money back. They are knowingly making an inferior product.

Read reviews on the same washer (Cabrio Whirlpool) that I had purchased in January 2017. I have the same problem everyone else has with it, not cleaning the clothes. It was such a disappointment. Had a Whirlpool front in loader for 15 years. Loved it! But the washing machines without the agitator on it is a laugh. What person thought up that design. What a joke on the poor unknowing people that purchased one. Im also upset at G&H Appliances for not standing by their products they sell. Found out that Lowes has a 30 day satisfaction guarantee on what they sell. Not buying from Lowes and buying a washer without on agitator on it. Was two big mistakes I made. I wanted to help out a small local business, but wont be doing that again. They sure are not worried about me.

This is the loudest washing machine I have ever had. Sounds like it is grinding. Called Whirlpool and said that is normal. Will never buy another one and will let everyone I know how noisy it is and not buy one.

Bought this front loader washer. It is unbelievable this thing will not wash a load properly. It refuses to spin at high speed because it is constantly out of balance even if you only have one or two garments and it keeps saying add more garments. As you keep adding garment its even worse literally. If you have anything that is heavy in this like a towel or a pair of pants or a hoodie or something like that for sure youre going to have to wash one thing at a time. I will never buy another one. I wish somebody would sue the living crap out of him for this piece of junk. I want my money back...

We spent a lot of time researching to make sure we were making the right choice, found the one that was right for us. When it got delivered there was a problem though, the plastic scratch protector film they put on the doors for delivery left an adhesive residue that looked like dull spots all over our new shiny black doors. I immediately opened up the owners manual to see how they recommend removing this blotchy sticky residue, assuming we werent the first ones to ever come across this problem, unfortunately they only provide generic cleaning tips. So I went to their website and found what I was looking for. I tried all of the cleaning methods they provide, none of them even came close to working. So I grabbed some adhesive remover and tried that, it worked great to remove the residue however my microfiber cloth (which they recommend explicitly) started leaving scratches all over the finish.I called the customer service to see about getting a new door delivered, thinking this wont be more than a 5 minute phone call since I had followed all of their steps they provide both in the owners manual and on their website. Heres where I find out that their policy DOES NOT cover scratches/cosmetic damage, period. I tried reasoning with them, I had them read their own recommended cleaning procedures, and we both concluded that I had followed their procedures to the T! You might think that if the all of the typical procedures didnt resolve the issue, that would be the point where the customer service reps would have the ability to make a decision that satisfy the customer, you would be wrong! They kept telling me over and over that their policy doesnt cover cosmetic, therefore there was nothing they could do. It was delivered with a defect of sorts, how is the customer responsible for that? The only way I can see it having worked out in my favor is if I had never tried to clean it myself and immediately called customer service, I still fear they would have given me the same line of cosmetic damages are not covered even if I would have tried each procedure with them walking me thru it over the phone. Lesson learned, I will never purchase another Whirlpool product!

After just 22 months I need to shell out $300 for a new microprocessor. My Miele lasted for nine years. In the olden days washing machines could last for 15-20. Do not buy Whirlpool, from what I understand its a dying company...

I purchased a Whirlpool Cabrio washing machine April 2016. I was so excited to have a new washing machine. I thought the 1st couple times I used it I just didnt have settings right. It uses so little water it doesnt get all clothes wet. If they are not wet they cant be clean. So I started doing very small loads. Then clothes were not clean. They stink. So I have tried every detergent out there. Nothing helps. Another thing it takes an hour or longer per wash to get not so dirty clothes. Not to mention it puts holes in my towels. I tried reaching out to Lowes where we bought it only less than 4 months ago only to be told they would contact Whirlpool. Whirlpool wanted to send tech that I would have to pay for just to tell me that the piece of crap washing machine is doing everything the manufacturer made it to do. I told him I was not going to pay so. I think with all the problems people there should be a class action lawsuit. DO NOT BUY CABRIO!!!

CABRIO GETS A ZERO RATING. We are sorry we ever bought this washer in 08. The unit had a defective main control board and was replaced in 2012. The factory authorized service agent from A&E literally robbed us of jewelry while in our home. Now the main electronic control board needs to be replaced again. Neither Whirlpool or their authorized agents are truly customer service oriented on the defective product. Neither are willing to make an honest attempt at regaining our trust. I have contacted both and neither will acknowledge or offer reconciliation. The problem with the main board and the recurrent F-50 error has been denied by Whirlpool although acknowledged in numerous consumer forums as this. Our family is now without a wash machine. We have not even received a simple apology for the theft from the service agency - even though their employee has been arrested. BEWARE!

I purchased this Whirlpool washer (model WTW7600XW2) on October 2011. Fabric softener dispenser is full of water at end of cycle. Repairman has replaced parts three times, but the problem is still not corrected. Today, I talked with a Whirlpool supervisor. She says this is normal. She told me to take the cup out and empty it. The cup is not removable, so she said I could blot it out with a cloth or sponge. I paid $800.00 for a washer with an automatic fabric dispenser that I must empty manually. I have used whirlpool appliances for 50 years of marriage, but this is my last one. I am very disappointed with customer service.

Purchased a Cabrio large capacity washer. It NEVER seemed to get the clothes clean enough, and after the sensors and bearings went bad within three years (out of warranty of course) I gladly kicked it to the curb. I bought a Samsung that has been great. Id like to support USA made, but not when it is AWFUL.

It is a top of the line washing machine. I have had it for almost four years. It is the best washing machine I have ever had. I have really enjoyed it, because; I am able to wash my comforters in this washing machine.

3/16/2019 washed a load of bed sheets, on the white clothes cycle, put the wash in at 9:21am. Left the house at 12:41pm. Wash still not finished! It was finished by the time I arrived back home, I was gone about 11/2 hrs. I have yet to complete a wash cycle in less than 1hr 15mins. I hate that I have no control over water level, that I have to put detergent in the bottom of the tub, and the damn lid locks! My clothes dont feel clean. Why does big brother get to decide how my wash should be done, when they dont pay my water or electric bills?

Purchased Whirlpool front load washer 2010. Had it repaired 2013. Paid $599 for washer & $648 for the repair. Mailed copy of sales and repair to Whirlpool customer service. Received call from customer service and was told to have a nice day.

I purchased the Whirlpool Cabrio Washer WT5500XW2 from Lowes on 9/12/2012, which turned out to be the worst purchase of my life. It did ok for over a year. It had always been noisy. Now it sounds like a jet airplane when it is on the spin cycle. This machine is not yet 2 years old. Do not buy a whirlpool washer. They are Junk. Plan on getting rid of this piece of junk and buying a new washer. Dont waste your money on Whirlpool!

Two days after the one year warranty ran out on our front load washer it started making a terrible noise. Of course the Whirlpool warranty was no longer in effect. The good news I was sold an extended warranty from Nebraska Furniture Mart. Called the Service Provider and was told they will only service the washer if it is not working. After several more calls they scheduled a service call in 10 days. We are a family of four, yes no washer is a problem. Finally the technician showed up and said the main bolt holding the drum assembly in place had broken off. He would have to order the bolt. It is now on backorder for 3 weeks. No washing machine for 4 people and now nearly a month is a pain. Not only did my calls to Whirlpool do nothing but the calls to the third party Warranty Company have been very frustrating. My call to the salesperson at NFM was very helpful, but didn’t help get our washer fixed. This is our second and last set of Whirlpool laundry pairs in less than four years.

Purchased an expensive, Cabriolet Washer in 2014 to replace a well used Kenmore washer. Sucked into the, Whirlpool is a good brand and spent more than I would have. Lid lock fault started about 3 months ago, googled fix and found this to be a very common problem with this brand. Have been able to override and reset it but it is very frustrating to deal with. Called in a repair person this morning who, for $140 told us we had a faulty lid lock and for $360 he would replace it. I contacted Whirlpool and asked if they were aware of this very common complaint (just google it) and they were not but offered to make a record of mine. Please do not buy Whirlpool. Very disappointed with their product and their response.

Had the washer 3 years. After 1st year had to replace motherboard and lid locking mechanism. Beginning of year 3 the basket came loose, the machine wouldnt spin the water out of the clothes completely and then it quit cycling into the next cycle, ie, the tub filled up with water for the wash cycle but then would not begin agitating. The water sat in the tub until the wash cycle was done and then would drain but would not spin. Each cycle had to be manually started by pressing the pause button, raising the washer lid, and then pressing the pause button again. I called a repair person who ran a diagnostic on the machine and said it needed a new pump, new motherboard again and something else to make it spin properly. Sorry I dont remember what the something is. The estimate to repair was approximately $759 so I am now shopping for a new machine thats not a Whirlpool.

Whirlpool Cabrio washing machine is less than five years old. First repair was replacement of control panel (under warranty). Second, third and fourth attempts to fix the out-of-balance problem which continually caused the machine to shut down altogether (even a small load) left my repairman totally frustrated after replacing most of the parts, finally telling me it just cant be fixed! What? I paid over $1,000 for this machine in Oct. 2007 and expected it to last many, many years. My mother-in-law has a washing machine she bought used in 1979 and it is still working beautifully. Ive read the 14 pages of complaints on the Consumer Affairs website and agree with Diana in Kissimmee, Fl - I am sick to my stomach not only for Whirlpool not recalling the Cabrio, but for Lowes and Sears and any other supposedly family-friendly business for continuing to sell it! Someone please contact me if you know of a class action suit being filed.

After 25 years my Maytag died. It was a Sunday so we just decided to go to Lowes & purchase a new one. They could not find my 1st choice so I bought the Cabrio. It is the worst washer I could have purchased. It determines the amount of water you need. Our clothes never seem to be clean & its very noisy. It has no agitator & is supposed to save water. Even putting it on the longest cycle our clothes do not appear to be clean.

I bought a commercial coin operator washer (Whirlpool washer model CAE2743BQ) for $800 and after using it for 4 months the washer stop working. The main board panel lights turned all and the washer did not start. Called Whirlpool several times and nobody could help me and told me to look online for a distribution center to get parts. The customer service only knew about regular washers not coin operator. The washer had only 3 months warranty from Home Depot and I was supposed to pay for all the repairs and Whirlpool would pay for parts. So far I spend $400 in repairs and the certified technicians could not repair the washer. They replaced the actuator shift, the main board etc, etc and nothing. The technicians reset the washer at least 10 times, calling Whirlpool tech support and the washer worked for one load and the main board lights stayed on all over again, the start button did not work. I sent a letter to the warranty department that I got online and they told me to call the same 1800 that I had called at least 50 times in the past year. Now it has been more than one year and the machine is defective. Technician said could be the soap that my tenants are using, or overloading the washer or an electric problem that they cannot identify. I gave up... I will not buy a coin operator heavy duty washer from them again. I requested a return authorization for a defective product and I did not get anywhere. Thanks.

We bought this Cabrio washer WTW6400SW2 several years ago. Immediately after having it delivered and installed, it started displaying an F1 fault code. The main control board was replaced under warranty. It happened again within six months. Another board was replaced. That board lasted another six months. The warranty was up by then, so I used the machine by hovering over it and restarting it every time it failed. After two years of this piece of junk, we put it in storage while we worked on the road. It was brought out on 10/01/11. I called a repairman (who came on 10/04/11) to come replace the board again. He told me that the last two times it had been replaced with the same defective board, that Whirlpool had never fixed the problem. He claimed he had the new improved board, which he replaced for about $350. Two days ago (361 days later), it went bad again. The same repair company came back and said it was the board again. I just tried chatting with a person working on the Whirlpool website. They (of course) said they would do nothing about the washer. They do not stand behind their product, obviously. Does anyone know of a class action lawsuit over these washers? It is a ridiculous amount of money to spend for a product that does not work. This is just wrong!

After reading all the reviews about the Whirlpool Cabrio washing machine, all I can say its just a piece of junk. We have replaced the agitator 3 times at $80.00 each, not including labor. Our clothes are never cleaned properly and it always seems to be out of balance. I will never purchase another Whirlpool product.

On Saturday afternoon, March 31 at 4:30 PM Eastern Time, my roper washer that was purchased on April 17, 2011 overflowed from the top. Water went into the air ducts and completely fried my security system. My husband was out of town at this time on business. The water went into the terrace level of my house and ruined the carpet, walls and ceiling. The restoration and insurance companies came immediately and were a tremendous help. I felt very safe with them even though they were in my house until 1:00 AM Sunday morning. My husband and I visited our Lowe’s store where we had purchased the washer. They told us to contact Whirlpool which we did on Monday, April 2. We were assured by Whirlpool that we would have a Whirlpool employee in our home to fix the washer. We were also told that we could not move the washer. After speaking with a Whirlpool representative, we received an email confirming the repair person would be in our home on Wednesday to repair the washer. During this time, I had to go to the laundry to wash clothes. This cost me $26.00. On Wednesday afternoon when no one had shown up to repair the washer, my husband had to call Whirlpool only to be told that the repairman would not be coming but he would be there on Thursday between 10:00 and 1:00. He arrived at 12:45 and the nightmare began. He had an “I dont care” attitude and if my husband had not been at home, I would have been very uncomfortable. After looking at the washer, he said a part would have to be ordered and it would be the next week before he could fix it. I asked him what I was to do about clothes to be washed. He replied go to the laundry, he was just the repairman. He also said I could use the washer but not to put a full load. On Tuesday night, April 8th, I was washing and I had the washer on medium load and the washer started leaking from the bottom. We still have not heard from the repairman, today is Thursday. Also, my husband and I work outside the home. It would have been so much easier to have the washer replaced but instead we have to wait. We had a washer to be delivered on Tuesday, April 2nd, but we are still waiting on them. Most of the restoration work other than the washer has been completed. Thank you.

I have a 1 year old Whirlpool washing machine (Model: WFW94HEXSW Serial:C04151969). The grease from the drum is found to be the cause of clothes being ruined during the wash cycle. I waited over 3 months for a replacement. The drum arrived broken. I ordered again, and it was then said to be on back order. The water shut off developed a slow leak, causing the water to fill, and flow out the front door, causing carpet damage. We have been forced to throw away good clothes, and pay to have our clothes washed, at a not so local laundromat. We feel it would be more than reasonable to have our washer replaced, and professionally installed immediately.

This washing machine has been nothing but a problem from the beginning. Theres always something wrong with it. Things that cost so much should last much longer than a couple of years! I have to clean out the drain about every 3rd time I use it or it wont spin out as well.

The machine purchased in 2011, 3 years old, will cost as much to repair as to buy a new one. I got exactly no satisfaction from Whirlpool. They said there is no recall so they wouldnt assist. There are only 2 people in my house, so how could the washer be so junky. What would a large family do? I have spent $140 and wont spend another dime on a Whirlpool appliance.

We bought our Whirlpool Cabrio 7 years ago and it was great at first. I have not had any trouble with it ripping clothing. The clothes are clean. Its constantly breaking down. First it was the drain pump. Then the main computer board went! I called Whirlpool and of course the lady says its not covered. I had back up though. Google is amazing! I asked why this wasnt a recall as all over the web, people had this same problem. I pushed and pushed and she put me on hold. Came back to say it was in fact covered. What? Really? What changed your mind? She wasnt allowed to tell me. Supposedly had something to do with the date of manufacture. So okay, they send the repair guy out, its fixed. Now tonight, the lid locks and nothing happens! This repair was about 6 months ago. Grrrrr. Its been one thing after another with this hunk of expensive junk. When I buy an appliance I expect it to be problem free for far longer than this. I am not getting a code or anything, just dead air. So frustrating with three kids not being able to do laundry when I need it randomly :( Has anyone else had this problem? The lid locks, then does nothing. I unplugged it, pressed off and restarted it. Changed settings. Nothing is working.

The washer started to show error code for the door and washer would not restart. After removing the top of the washer and checking the door switch to see if there was a loose wire, I traced the wire back to the micro control unit, and upon inspection of the micro control unit, I found that the terminal that the door switch wire was attached to was loose and not making contact with circuit board.Although the washer is out of warranty being 7 years old, this is clearly not a part that is subject to wear and tear. The part was clearly manufactured poorly. I looked on the internet to purchase a new part but it seems that all micro control units are out of stock. This makes me wonder if one should start a class action suit as my part could be one of hundreds that was poorly manufactured. I called Whirlpool to see if they would send me another part to replace the bad unit but they said that because the washer was out of warranty, they could not help.

We have the Cabrio model and are thoroughly pleased with the performance. My only issue is the amount of sounds during the spin cycle. Otherwise, the machine is quiet. I like having the automatic dispensers for soap, bleach and fabric softener. Not having the classic tub makes loading a little different as the clothes need to be distributed around the side of the tub and avoid the center.

Washing Machine Model WTW4616FW - I purchased this machine at Home Depot after I had to return my Samsung Costco machine that was recalled due to the glass top flying off. I was attracted to it by its simplicity in design and price. I have had it almost a full year and love it. I like that it has the deep water wash for over-sized items and a full-sized agitator. I was shocked that it was actually Made in America. I highly recommend it and I hope they keep making this reliable machine that gets the clothes clean. Awesome machine without the bells and whistles that I dont expect to breakdown. Way to go Whirlpool!

I purchased a Whirlpool duet set on sale at Lowes about two years ago. The front loading washer has been leaking when I put in a full load of clothes. It usually floods the floor when it leaks. I am upset and very angry because this leak has ruined the doors to my washer doors. Apparently, the defects with this machine was known by Lowes and the Whirlpool company at the time that I purchased it (thus the sale price). This was not forementioned at the time of purchase. What a lousy way to do business. Whirlpool screwed me. Shame on me. Never again.

We purchased a Whirlpool Cabrio Washer in 2010. I have had nothing but problems trying to wash black/dark clothes, it leaves white stuff. I assume its soap scum all over the clothes. Ive tried cleaning the machine with Refresh more often than recommended and it still has the same problem.

I have a brand new Whirlpool washer (Model WFW9640XW). It has been broken for 3 of the five weeks I have owned it. The Whirlpool cusotmer care cannot get me a working part in order to fix the machine. I am being told that I just have to wait until they find the part, with no end in sight. I am held hostage now that they have my money. I am told there is nobody I can talk to to break this impasse.

In August of 2013 the lid on my Whirlpool Cabrio, model #WTW7800XW0 simply fell apart. This washer was purchased from Lowe’s in Live Oak, Florida on August 23, 2010. Lowe’s put me in contact with the authorized repair service, A&E Factory Service. The A&E technician arrived and told me the hinges were the cause of the lid breaking apart. He ordered a new lid and new hinges. When the lid and hinges were delivered the technician came back to my home and looked at the hinges again and said they didnt look that bad so he didnt bother even opening the box with the new hinges. He just put the new lid on and said I shouldnt have any further problem. The total cost of the new lid, hinges and service call amounted to $385.50. Well, here it is - not even a year later and the same problem is back with me. Yesterday (July 23, 2014) I was doing a load of laundry. When the load was complete and the lid lock turned off - the lid actually sprung upward and now the lid wont close. It seems that Whirlpool is fully aware they either have a design flaw of defective lids and they are gouging the customers for their errors. The Cabrio model is supposed to be top of the line - certainly not a cheap machine. I was, at least, happy with the performance of this machine cleaning my clothes properly but this lid problem is ridiculous. I do not plan to purchase any Whirlpool products in the future if they do not make things right by myself and hundreds of others with this same problem.

My Whirlpool Cabrio cannot wash sheets, blankets or any of this size. It balls up in the middle and form a bubble and only part of the items is washed and washing powders are trapped. I have purchased more sheets in the past 4 years than I have in the past 45 years of doing laundry, because the washing powders are not washed out. I wash on second rinse also, never fails and it still does not get all of it out. The clothing gets off balance if it was more than 3 small items. I have a leveling tool that I put on it often to make sure it is level. It’s something within the machine. I will never, never, never purchase any more Sears’ product. If anyone has jury-rigged this machine to work, please let me know. Sears has refused to help me, even today.

Sounding like a broken record, this washer is such a disappointment! I had high hopes for this top loader and thought I did enough research. Bought a Cabrio in Oct 2016 and have never liked it. They will have you believe it’s your fault... the wrinkly clothes, the clothes not clean enough, the white marks over all your clothes... you can’t change your detergent or softener enough and change the amount enough... it will still be there. So disappointed??? Want my front loader back!

My Whirlpool Cabrio washing machine. f1 keeps showing up on washer on. Shuts off again and again.

Whirlpool Duet 3.9 cu ft High-Efficiency WFW9451XW00 - Hear my first experience with Whirlpool. I purchased a washer machine 30 April 2014. Guess what - machine stop working suddenly on July 30th, just about three months later. I had a lot of guest from overseas. While they visit me, I did not have my washer machine. How embarrassing. It was big mistake to buy Whirlpool. It is all made plastic inside and they uses cheap Chinese material. Anyway, technician came house to check what the problem was... all control system was burned. He ordered almost 10 parts from Whirlpool on 04 August. Whirlpool scheduled delivery for 20 of August. I called them for them to send the parts faster so my guests could wash their clothes. They send them little faster for August 16. After a day, technician was in the house again. I waited about 3 hours for him to fix my machine. He was really nice guy. He put install all new parts. Just in front of me, new parts broke after 5 minute. Whirlpool still did not contact me about their decision. Today is August 26th... I called them 5 time already - Nobody give me useful info. NO Whirlpool, guys - bad service.

I have not use wash machine for 46 years, however, since I the caregiver for my wife (with Parkinson), Im the user of our washing machine, High Efficiency Whirlpool for 8 months. It Is very easy to use including the dials. It is very efficient to use.

On 12/31/2009, I purchased a Whirlpool Cabrio, model# WTW6800WW1. I was excited as we have never spent that kind of money on a washer. We felt as though we had purchased a higher end washer and would have it for years to come. Wrong! About one year in to its use, I began to think it was getting louder during the spin cycles. I thought I was just being critical and it was just my sensitive ears. Now just past the two-year mark, I know it was not me. It’s the POS washer. It is so incredibly loud, not that you cannot be in the same room as it is during the washing time especially the spin cycle. In its defense, my clothes got cleaned.However, I know that the bearing is eventually going to give out and I will have a mandatory repair on my hands or have to pay someone to fix it. Either way, it’s a lot of time and a lot of money to fix a two-year old washer that should not need to be fixed. I attempted at getting Whirlpool to stand behind their product. No chance, no way. Good luck with that. Their washers last about 2-3 years. I will never purchase another Whirlpool product. This is a horrible product which is matched by their horrible customer service.

I bought a new house 2.5 years ago with all new whirlpool appliances. This week Im told the washer transmission is defective. Unbelievable! I only wash 4 average loads per week. This is a problem I would expect in 8-10 years. I am going to replace the unit with another brand.

I purchased my Cabrio washer in April 2011 from Lowes. Huge mistake. The washer has broken 4 times under normal family of 5 conditions. The last time was in March 2015 - the barring was stuck on the drum failed to allow it to spin. It was stuck to the point where the unit needed to be shop repaired. It took 2 weeks to remove and replace the fail part. I just called service again today for the same noise as last time. It kills me that I spent so much $ on a product from a well-known company only to have it fail so often.

Whirlpool Washer W10740628A - So disappointed! I have made adjustments for a year trying to get clean clothes from this machine. Compared to my previous machine which wore out, I now use more water because only deep water wash provides enough water; I always choose double rinse because if the machine does not clean, I do not trust it to rinse effectively either. I use more Tide than previously per wash; I use more Clorox than previously per wash. Everything from tea towels to heavily soiled jeans show stains and soils after washing. Instructions say not to spread the item in the washer but allow it to stack on itself, so twisted and tangled wet clothes are the result. I try to soak and scrub all visible dirt before I start the machine now; additionally, I use a mop or plunger or my hands to thoroughly immerse the clothes in the washer, somewhat like my mother did in 1950s. What on earth is this about and what is the buyer supposed to do???

We've had a of Whirlpool washer and dryer for well over 8 years now. The only thing we've had done to it during that time was to give it a "tune up". That was done by a friend and only took a half hour or so. I don't know exactly what he did to it but the "tune up" didn't require any parts. In fact, when my friend was finished with his version of a tune up, it was as if it were turbo-charged and our clothes came out cleaner than ever. The washer runs quietly, as far as washers go, and the capacity, washing options, etc. are perfect for a washer that gets a ton of usage.

I bought a new washer thinking I was upgrading. Wrong!! Well the new so called technology they put into these machines is overrated. They took a good thing and instead of advancing they have took two step backwards in time. I wish I had kept the old washer I had. I think I would rather use an old time wringer washer my great grandmother used. They are probably faster by hand. This new Whirlpool grabs every string on my hoodies and twist my clothes so tight in knots. I cant even remove my clothes until I fight and get mad enough to write a review. Whats up with these new washers?? Get rid of the slots on the Agitator!!

I have had my Cabrio set for two years only and the washer has a error code of F6 and E3... pretty much does not work properly and need to swap out main control board which is about 200-300 for the part. I’m very disappointed in this product for as much I have spent on it. My old school top loader lasted longer than this piece of junk! I believe the steam from the wash is going up into the control board and messing it all up! Water and electricity does not mix! Maybe they need to relook at their products. I want my money back!!!

We bought a top loaded Whirlpool washer, model WTW5000DW2 last May from Lowe’s for a summer beach cottage. It has been a terrible experience. There was a 30 day warranty from Lowe’s which unfortunately we missed because we had not moved down for the summer till after the 30 days. Working through Whirlpool, they sent an independent contractor out 5 times over the summer. Control panel was replaced twice. It never worked properly. I’m now back for the summer, and it still does not work. Do not buy this washer.

Never ever plan to buy a Whirlpool product. I took the washing machine in December 2008. System was not got at first time also. I called service center, and he came and asked to put this and that. Again, it got a problem. This time, he told me to change powder. I was shocked how a powder became a problem for its failure in washing clothes. Next, he told me to put a stand. After a long interval of 6 to 7 months, I got fed up and called him again. He told me it was not in the warranty. Its the worst service. Zero percent satisfaction Hats off to Whirlpool service. Please, friends, never buy cheap Whirlpool products.

I have had this Whirlpool Cabrio washer for 4 years. I had to rebuild the drive unit once and now the control board is bad. If I didnt do my own repairs I would have spent well over the cost of the washer in the 4 years I have owned it. This is the worst washer on the market. Not to mention Whirlpool support will not work with you at all. DO NOT BUY THIS PRODUCT.

I am a retiree after 35 years and 5 months, the last 20 plus years on salary. I purchased a new Whirlpool washer on April 18, 2012 at Lowes in Tiffin, Ohio. The clerk said to take the receipt to Clyde to apply for my rebate. I was informed by a receptionist that we only get a rebate if our purchase is from Sears. I only went to Lowes because of the urgency and was not aware of this change in your policy. I consider this a real slap in the face after all the years of what I consider excellent service to Whirlpool Corporation.

We purchased this Whirlpool washer 5640XW3 from Lowes. It doesnt clean the clothes. Even if I run them through a second wash cycle, the clothes are still not clean. Called Whirlpool and they said nothing is wrong with it. I use HE detergent and load clothes around the agitator as directed in the manual. Still, clothes are not clean.

Six months after purchasing my Whirlpool Washer model number WTW5000DW0 I would hear what sounded like rocks in the bottom of spin drum during spin cycles. Then noticed it was taking longer for clothes to wash and sometimes the water did not completely drain. Called for Service under LOWES warranty (the worst people to deal with). Tech comes removes a penny and dime and tells me that is the problem. Leaves. 45 minutes after he leaves there is the noise again. Call and set up for this Service Company to come back. Even though they went out of business prior to the appointment Lowes Service would not listen to me and insisted I stay home ALL DAY for someone who did not show up. Repeated calls to the Service Company resulted in nothing - phone disconnected.So finally after much frustration I am given new appointment with new Service Company - PARRISH. Tech comes in here five minutes and wants to know the sound, I explain. He checks out the unit and tells me it is a major problem and the part and labor will be costly. Best if they just replace the machine. His added comment - I see a lot of this. So if this machine is such a problem why was it not recalled? I am getting a replacement as I have warranty and machine was not a year old when problem started. Lowes Service Contract is another problem but I will deal with that later.

We live in Hawaii, so the price for our stacking closet size unit was exorbitant. It was over $1,000.00. It is small so the size of loads are small too. We bought one that is supposed to sense the load size and deliver the correct amount of water. It does NOT do this. Reviews online show complaints of this same nature. It does clean well but we have to do very small loads to get that.

I just bought a new home, and it came with what was described as top of the line Whirlpool appliances. The Cabrio toploading washer worked for two loads then just stopped. After arguing with Customer Service for a while (They insisted this must be an installation error.), I talked with the builders. They gave me a different customer service number. My second call got me a repair appointment, during which the repairman discovered that the pump was in fact dead. Because this is a new model, they didnt have a replacement on hand. So, I will have to wait an additional week and a half before the part is installed. This is a product that retails for around $1000, and it lasted less than one day. My last washer cost $400 and was still running fine when I sold it after 10 years. I can already see the handwriting on the wall. After my warranty is up, I will have to replace this hunk of junk with something that has some reliability.

Purchased Whirlpool washing machine two years ago but transformed into junk within two years. Fraud company only searching ways to loot the money of the innocent customers and manufacturing such appliances which greasing mentally.

Cabrio washing machine - I have had the exact same problems as all of the above... lid locks occasionally ... after many frustrating tries. I am ready to pick up this stupid washing machine and pitch it in the junk pile! Soap on clothes so I have to redo ... except many times it takes forever to get the stupid machine to restart... Most times I end up rinsing things by hand in the sink. We are constantly itchy from soap residue. My clothes do not come out clean. Especially the towels. Clothes are not spun out as much as they should be... Have been doing it over again by hand many times... which is not good because They still have way too much water in them and it takes 2 -3 Times longer to dry them! I am so disappointed in this set. I always thought Whirlpool was a great brand but, sadly, I was terribly mistaken. Never again. Finally got someone to say they have to replace all the controls. They say they will send parts but I have to pay someone to change it out... sounds like they admit there is a problem but will not accept full responsibility for it. I did not make the item so why do I have to pay to have it fixed? I believe they should issue a recall and make all of us believers in them again. I guess its my fault for buying their product? So... doesnt clean, spin, rinse, lock and has a bad odor... not a great product, is it?

Whirlpool Cabrio Washer model WTW6400SW2, serial CU2372784 type 480: I have had this set for about 4 years now. First, I had to replace the motherboard. And now today, I found out that the center post seal was leaking and caused a lot of damage. I was told that it would cost around $300 plus to get it fixed. I have seen on sites that this washer is a lot of trouble and the makers need to fix these problems. Also, the washer sounds like a jet running. We need the makers of Cabrio to step up and fix these problems or refund us the money that we have paid out for this thing. We, the people who have bought these machines, need a lawyer and to start filing lawsuits against these people.

My old Whirlpool stopped working so I purchased a new one 2 weeks ago. I have had 3 items ruined since using this machine. It is leaving blotchy spots on the clothes and they will not come out. I do not use bleach but the spots look like bleached spots or stains. After reading other reviews I would like to know what the manufacturers are going to do. It is not very economical if we have to rewash everything or replace clothes the new washers are ruining. I have just spent hundreds of dollars for something that does not do its job and would like to know what the solution is. Is there a model washing Machine out there that still cleans clothes? Since mine is only 2 weeks old can I trade it in (Lowes)?

I purchase this machine over 15 years ago. It’s still working, washes the clothes. The only problem the section where the bleach is poured is completely rusted out. The machine has definitely lasted beyond the 15-year cycle. I intend to purchase a new one. I probably would buy the same brand.

Top loading Washing Machine Model #WTW4950XW2 - You would think that a big company like Whirlpool would make quality washers. NOT! Our top loading washer bought in late 2011 has been making loud noise during the washing cycle for the last 6 months, and last night was struggling to spin. Seriously, with just my wife and myself using the washer once a week, this washer should last over a decade! So I called Whirlpool and explained the problem... and, as expected, they cannot help me as it is over the one year warranty. NO MORE WHIRLPOOL BRANDS FOR US!

We purchased a Duet washer in Feb 2011. On Nov 2011, it started making a very loud noise when it would spin. We contacted the warranty company, not realizing it was still under the manufacturers warranty. The warranty company came out and took a look and claimed it would be about $1500.00 in parts to repair. We contacted whirlpool and they also sent a service person that claimed the same thing. Both service people claimed that the other did something to the machine and it was the others responsibility to fix it. We have contacted whirlpool and the parts have been ordered. We were informed today that they are on backorder and will not be available until some time the middle to the end of January. When asked why they just dont replace the washer, the answer we received was that was not the policy.

I am waiting for the third repair on my front-load washer. I purchased them a year ago and was very satisfied with the ease of use. But in April of this year, the E2F3 started flashing up after I put in a load of clothes. I called the repair line and they sent a guy to check it. Determining it was a sensor, I waited three days for the repair. Then, almost two months later, now, it did this again. He called WP and they said to replace the sensor again. I waited two days for the repair. Before he left, he started the washer to run through the cycle - no problem. I then put in a small load of clothes, and almost immediately, the washer stopped and the E2F3 was flashing again. I called for a repair, and am again waiting (without a washer) for the repairman to come back on Tuesday!!!Today is Friday. I have been four weeks almost without a washer this year. Thats also the $20 I have spent this last week to wash clothes at the laundromat, not to mention the frustration of waiting for the warranty line to pick up and the hassle of having someone here when the repairman comes. I am glad I purchased an extended warranty for this product, but Whirlpool should make their products to last!

I have owned the machine for 1yr and 6 months, bought new from reputable company. The washer always had kind of a clunk sound which the manual says is normal. Clothes would have white marks and streaks after was but disappear when dry. Clothes would seem damp, never like they were completely washed. Went to do a load last night and thats when it stopped working. Powered on, cycle selection was fine, lid locked, typical clunk noise, then nothing, no water. Paused the cycle, lock lid light flashed but didnt unlock. Machine powered off on its own and unlocked. I powered it back on after 30 minutes and it wouldnt let me change the cycle, panel selection was frozen. So I powered it off and contacted repair. They think its the water inlet? Pending repair to see for sure. This is not OK! I had an older machine from the 90s that was still working before I bought this one. So sad to have this type of product from this company.