I purchased a Whirlpool Cabrio washer (WTW6500WW1) on 9/11/09 for approximately $800. Now three years later, it needs a new rotor and stator costing $470 in parts and labor. I called Whirlpool and was told I could get no help with the cost of parts because of the age of the machine! A simple Google search of the F51 error code that I am getting will show you that these machines are $800 pieces of junk! I am not repairing this machine. I am going to run it until it dies and simply buy a new washer. You can bet your sweet self it will not be a Whirlpool! I can only hope to inform enough buyers about this to keep them from the same fate.

Whirlpool Cabrio, H2 washer system type 588 01, serial # c0303 10 - We have been in our condo 5 years. The washer & dryer was here and new when we moved in. I have been displeased with it from the start. It takes forever to wash through a load, and the clothes are just as dirty after being washed as before. I soaked some whites in Clorox overnight and ran through using Tide and Downy. Then the stains and dirt were still there. I ran them again it was not any better. I had a professional from Hagadorn come. They could not find anything wrong. It cost us about $100.00. Others in our area have the same complaint. I have never been satisfied with this wash. It just does not get the clothes clean. Please help!!!

I purchased a (second) Whirlpool washer (WFW87HEDW0) in October 2014. Since purchasing (and to this day), I manually dried the rubber gasket after completing my daily washes, knowing that mold growth was possible. I wash one to two loads of clothes about three to four days per week. During the first year, I did not notice any mold in this area and was confident that the manual drying and cleaning with Affresh was preventing mold growth. However, at the beginning of this year I discovered a little mold growth, which has slowly been increasing, in the inside lower lip of the rubber gasket. The image attached reflects mold in its current state. I was very surprise to see this happening since my diligent cleaning has been thorough and never ending. I even remove the soap dispenser tray to clean and air dry it outside of the washer and leave the washer door open at the end of the daily washes for extra fresh air circulation. This is my first official complaint about a Whirlpool front loader washer, even though I previously owned another (GHW9200LQ0) before this one and had mold growing on the rubber door gasket but, unfortunately, never officially complained about that old machine. Now, I dont qualify for the $500 compensation because I never officially complained three times within the first five years of owning the old washer. To my dismay, I did not immediately realize I had mold growth in the old washer. It was only until years later that a repairman told me that I had mold growth in it. In addition to telling me the price of replacing the rubber part and replacing a broken water pump plus labor would cost as much as buying a new washer. Before purchasing a new washer, I researched and read many reviews about Whirlpool and other brands before deciding on this new Whirlpool. I decided to give Whirlpool another chance and to follow their recommendations on the proper cleaning of the machine. Once again, I am disappointed and angry with Whirlpool and, now, have to figure out what to do with my current situation.

I am not pleased with my self-cleaning oven. I dont even use my oven that often and I cannot get off even the simplest of stains on the sides, top, and bottom. I have tried to clean the oven three times and the stains from pie drippings are still not coming clean. It should not be this hard to clean an oven because my last oven was so much better and it was not Aqualift. The top of the oven is also very hard to keep the burners clean and looking like new. I am very disappointed in this oven and believe that this is false advertisement to the consumers. I pride myself in keeping my kitchen looking clean but this just is not working for me!

I bought a brand new KitchenAid stainless steel refrigerator for close to $3,000.00. It has a big crack in the back casing which Im sure is affecting the seal. It is still under manufacturers warranty. Whirlpool sent out a technician to put a yellowish plastic epoxy to seal the crack. When I told him that this was unacceptable as it dries yellowish and has a dull finish he explained that that was all Whirlpool was willing to do.I have been dealing with Whirlpool for 4 weeks now and they refuse to repair the crack and they deny any manufacturing defect. I have sent them pictures of the crack and they still refuse to resolve this issue. Very bad, horrible experience with customer service, long waits on the phone, rude and ineffective employees. This CLEARLY is a company that will not stand by their product and I recommend everyone to CLEARLY stay away from purchasing any Whirlpool products. They will be paying a lot of money for very poorly manufactured products.Please, please, do not purchase Whirlpool products! You will be happier spending money on a company that values you as a customer before and after the sale. Obviously Whirlpool would rather forget you after they have sold you their product and have their money. Thank you for reading this. I hope I have saved potential appliance customers from making the same mistake I made. DO NOT BUY WHIRLPOOL!

Purchased Black Ice French Door refrigerator in December 6, 2012. Used warranty first year due to loud noise & replaced whole back panel in top part. They seemed to know it was a design flaw. Thought all would be well. Purchased extended warranty for second year and did not need so did not extend again. Now it has been 2 years and 7 months and the ice maker had to be shut off due to water running down outside. The refrigerator is no longer cold enough--60 Degrees (too warm) and freezer door would not close all the way (had to duct tape it shut). I certainly expected it to last longer than that for a $2300 fridge. The old Kenmore was 15 years old and still worked. After reading all these reviews it is time for a class action lawsuit! We have to buy another now but it wont be Whirlpool!

The refrigerator has worked OK except for occasional freezing towards the back. However the vegetable bins have both broken starting with various parts of the handles in front. We eventually replaced them. A brand new one arrive already broken. Same cheap brittle plastic. No alternative available. The company denies any problems or complaints about the bins. Feels like a small profit center for them.

You have to take into account that this microwave doesn’t heat up as others I’ve had so even if the instructions call for something to be cooked for 5 minutes, you have to add at least 2 minutes more. If not it would be undercooked.

I bought a new Whirlpool gas hot water 40 gal tank from Lowes. I Installed it, but the pilot light would not light. So Cal Gas Co came out and said they did not like the new design, but that was how they were now making them. Gas is shot out from a pipe into the tank, however its fairly open. The pilot ignitor is similar to the one on barbarques that often do not last. You cannot get to it to light it manually. Several calls were made to Whirlpool and they sent a repair man out to fix it. You can imagine buying a new hot water heater and having it work part time. The repair man explained that the unit needed a new thermopile, but he could not put one on until whirlpool authorized it, which they would not. After a rather heated conversation with whirlpool they agreed to FedEx a part overnight. Of course the repairman could not wait for me to call and had to come back again. The pilot light still does not stay lit, and Whirlpool now wants to talk about how the tank is vented. This has nothing to do with the pilot light, nor did putting in a new 1/2 gas line and valve as per Whirlpools request. Whirlpool has a problem and they refuse to acknowledge it. However, it is Lowes that chose to buy from whirlpool and they do little if anything to stand behind their product and gain consumer confidence. My suggestion would be dont buy whirlpool, and shop at Home Depot.

I bought at Lowes. The first one was sent back (doors stuck, suction cracked lining). Now the temps are not working in the fridge or freezer. All the food got dumped. Its sad. My old one lasted closer to 25 yrs. (and may I add up to ten children). This one has only been used by adults. I thought I could trust Whirlpool?! I sent info to local Lowes. We will see if theres any help.

Bought this washer and dryer on sale at HD. The washer hasnt worked from the beginning. The clothes dont get wet because its an HE. I have to add buckets of water to even get the clothes wet enough to wash. The clothes come out with a residue on them. We use liquid HE detergent. It appears Im having the same problem as the majority of posters here. I will NEVER buy another Whirlpool appliance. There should be a class action suit to get Whirlpool to respond.

I own a top two door refrigerator cabinet with a middle drawer meat cooler and a pull-out out lower chest freezer. The ice maker is built into the door and it is a very simple to operate and stable appliance. The refrigerators space is very functional and flexible for your food storage.. We have moved it 3 times and never had a problem. It is my wifes favorite appliance and fits our needs perfectly without a lot of bells and whistles. The ice maker filter is easy to change and the ice maker itself is super reliable. The model number is WRX735SDBM00. We have been Maytag and Whirlpool appliance owners forever because of their reliability and the ease of used to clean them.

When we moved into our home this past year there was a Whirlpool gas stove model number W10406473A. We have the plastic knobs on the front of the stove which need to be pushed and turned in order to turn on the gas. I recently ran into a serious problem where my cat walked across the knob area and pushed and turned the knob causing the gas to come on the stove. This is a problem due to the fact that a child could have also have easily turned on this stove. This is a definite fire hazard as well as a carbon dioxide problem. I warn anyone with this stove to replace it with another make or model immediately. Im in the beginning mode of looking to see if a recall has ever been made on this model.

What is the brilliant idea of a mode dial on a washing machine that needs to be pushed in or pulled out to engage its function??? In other words, why is there a free-spin mode of THE DIAL itself? Okay. IN OTHER WORDS, why not just let the handle part of the dial stay affixed to the red line mark, so that they continuously turn together at ALL times???

This refrigerator was already part of the appliance package that came with the property. I dont think if I had a choice, I would choose this brand. The stainless steel finish has rust spots, the top shelf has cracked and it is less that 5 years old.

Whirpool Part #WPW10564292 refrigerator handle - I am a property manager who has 264 units. We have only been open for 1.5 years and have had to replace 30-40 door handles because they crack at the top where screws are. We tried calling Whirlpool Customer Service because obviously this is a defect and she said they looked in the system and didnt see any recall or issues. We also asked for a representative from Whirlpool to stop out so we could show them the issues and she said we have nobody in the area. We have 9 service requests outstanding that need a new refrigerator handle. On July 19th, we ordered 3 handles from our distributor and we were told theyre on back order until September 6th. When I called at the end of August to make sure we were on schedule with delivery, I was informed they are now on back order until November 5th. I just called our part rep. this morning and now they said the current part number does not exists and gave me the new part # W11026870, and they are on back order until mid or end of November. I am not going to keep quiet about this issue. We have paid $79.89 per handle on a refrigerator that is only a 1 to 2 years old appliance. I am requesting a returned call or email on what you are going to be able to do for us. This is not right or fair to a company that spent a large amount of money to have your appliances in 264 units.

This is a comment for the person with the ice maker problem. I have a side-by-side, in-door ice dispenser that clogs up. First sign of problem is either the ice wont come out or it comes out crushed. What happens is frost builds up in the path the ice takes at a couple of different points. The only solution I have found is as soon as the problem starts I turn off the ice maker using the switch on the inside of the freezer. Then let it empty with normal use (if you wait too long youve increased your problems). The release button for the ice bin has frozen by now so you cant just lift it out. The bin needs to be empty. When it is empty, work the bin loose and take it out. Youll find that frost and maybe cubes have collected, frozen and blocked the passage. Be sure to turn the ice bin on its side and spray water into the undercarriage to melt and remove all the ice build up there. I use a hot sponge to melt the frost in the ice tube and then dry everything. This gets messy so be prepared to have water on the floor. Dry the ice bin and reinstall it. Ice cubes will be ready to drop from the ice maker so it wont be long until you have plenty. I live in Florida with high humidity so need to go through this process about once a month. Its a pain, but now it is just part of owning this unit. Good luck and hope this helps.

We purchased our suite of appliances from Home Depot, this was a great experience. Unfortunately that is were it stopped. Our 1st refrigerator caught on fire in the electrical within the unit. We got a 2nd refrigerator sent to us and it came damaged. Then they sent us a 3rd refrigerator and it caught on fire in the electrical as well. Weve been dealing with this all since August 27th 2019 and here its now October 14th 2019. At this point I feel this model of Whirlpool is truly unsafe.

I bought a Whirlpool gas hot water heater in 2005. In the first 12 months I replaced either 4 or 5 thermocouples and a total of between 15 and 20 from the time I bought it in 2006 and 2012. Only 1 time did the company replace one of them. When I would call them the rep would say things like, There may not be enough ventilation or Was it installed by a licensed technician? The 1 time they did take care of a problem the technician they sent out said NOTHING was wrong with the ventilation or the way it was installed. Oh yea, Customer Service told me that they did me a FAVOR (exact word) when they did that.In 2012 the hot water heater went out for good. The company would NOT do anything about it. I took it back to Lowes where I got it and they replaced it for me since the manufacturer wouldnt. The new hot water heater went out after only 3 years. I turned the hot water on and it was not getting hot so I checked the hot water heater to see what was going in. I found the pilot was burning, but the burner was not burning. I turned the water heater off and and checked everything out. When I tried to relight the water heater, guess what? It will not light. I am now being told that this heater has NO warranty, this 3 year old heater. There is MORE but I wont go into that now. Just know this has been the WORST product and the WORST company I have ever had any dealings with, PERIOD!!!

The damper switch at the top of my water heater, one I purchased at Lowes stopped working. I talked to someone at the local store, and I was told I had to contain the manufacturer. I called the number on the front of my unit. The tech talked my husband through the restart process...not once, but on two separate occasions. We were told that because it was intermittent, something they decided Over the Phone, they could do nothing. They would neither send a replacement part nor a technician. By the time we had to call back two days later, restart was impossible. JUST to get the part, a specialty piece, we now have to pay for expedited shipping! And either install ourselves, or wait 5 days After Arrival (!!), to get the stupid thing fixed! If they had sent the part out originally when we asked, we wouldnt have to wait for hot water or pay anything for a warrantied piece! Its a racket. Stay away!!!

I am a single parent. So I was very excited when I had saved enough to purchase a new washer and dryer. I purchased Whirlpool because I had been told that was a good brand. From the beginning, I was having issues with the washer (Whirlpool Front Loader model #WFW8300SW04). It wouldnt start or it would not spin, or it would just lock and not be able to get it open. I had purchased a warranty. So I called to have it serviced. The tech came and told me that I needed to have my floor leveled under the washer. I hired someone to concrete under my washer and dryer. Again the washer still did the same thing. I used the warranty again. The second tech told me that I needed to have my electrical outlet changed. I again hired someone to change the outlet. Yet still the machine didnt work. I then hired a tech to come out and was told the mother board needed to be replaced. Had that done. The machine worked for a short time with no issues. But yet again it wont start, or wont spin, or it locks and you cant get it opened. I contacted Whirlpool and their answer to the problem was they would be glad to set up an appointment to send out one of their techs (at my expense). I have hired another tech and being told that the mother board once again needs to be replaced. I am so disappointed with Whirlpool and their service. I dont understand why they won’t stand behind their products. I will (when able) purchase another washer, but it most definitely will NOT be Whirlpool. Anyone else having issues with the same model? Would like to hear.

My Whirlpool Cabrio washing machine. f1 keeps showing up on washer on. Shuts off again and again.

We bought this microwave/hood combo at Home Depot and installed it in our second home roughly 16 months ago. We used it very little over that period because the home is only for vacations. The plastic handle began to disintegrate where it connects to the door (top and bottom) to the point where there is very little plastic remaining. We called the service center and the woman attending to us told us she had never heard of that happening before. Either she had just started working there that day, or she was lying because there are dozens of similar complaints on this very website.I do not understand what is to gain by denying a manufacturing defect. It simply makes no sense to me that a company would allow their reputation be so tarnished. What an ignorant and short-sighted business practice. I will never, ever buy another product from this company. I will also be sure to tell anyone who will listen what I think of the shabby service they gave us.

Note that most of the complaints are about gas water heaters, but the electric water heaters dont seem to be much better. Mine, barely made 4 yrs old and both elements and thermostat went. Had plumbers in for estimates in to repair - much cheaper to install a new one (No...not a Whirlpool!). Very disappointed in the product.

Whirlpool Gold with bottom freezer, had it for about eight years and no problems. Great seal and great storage space. Also plenty of space in the freezer. We are a family of four. It is extremely quiet. There is flexibility as to how to mount the shelves and they are easy to clean. I have never had any spoilage.

I bought the Whirlpool bottom mount freezer to find out there were problems with the drainage. I contacted whirlpool and they sent the parts to fix it but they did not send a repairman. I’m 80 years old and I’m not getting on the floor to fix this issue besides pulling it out to get behind it. The ice will buildup in the freezer so I have to empty the freezer and break up the ice. If I don’t break up the ice it will frost over. I will never buy another whirlpool refrigerator and I’ve been looking at replacing this one.

I have a lower end 4 burner model but I love it. Both power burns are in the front (I would change that) and electronic ignition. The oven temp is true and heats up quickly, I bake upwards of 700 cookies at Christmas time. Even being a lower end model it works great and I use it everyday. I think it is more energy efficient than the model that I replaced, which I replaced in order to have the electronic ignition. I would recommend this Whirlpool Range!

My mother and grandmother swore by Whirlpool washers. They were the best. So, naturally I never wanted any other brand - then came the digital machines. End of an era. My experience with my 1 year old digital machine has been very frustrating. I do not like it. I prefer the old system.

I also have the same water running into the refrigerator problem that so many people have reported. Im about to throw the Whirlpool out and start over. It is such poor business that whirlpool wont admit that the appliance has a major problem and fess up to correcting it for owners. I will never buy another Whirlpool appliance and will warn everyone to also steer clear of Whirlpool.

This product is just DISAPPOINTING. The gas knobs got stuck TWICE IN 13 months only! The range is NEW! The first time 3 out of the 4 knobs broke, this time only one. It would not turn off, so we are forced to climb on the counter and turn the gas off every time we are finished cooking and turn it on again. The company wont be able to send us anybody till next week, which will force us to go on like this for NINE days plus, of course, the time it will take to order the parts needed.There is not even a back up emergency service, which should be in place since we are dealing with GAS! I have heard complaints about this product in this area: in my opinion the range should be recalled. Of course, the representatives one talks to are all trained to keep calm and reply the usual things: Oh, I am sorry etc. but the bottom line is that neither the product nor the customer service are good (the first customer service person was not very friendly either). I highly recommend that you AVOID this range if you are considering buying a gas one with double oven.

Bought a new Whirlpool side by side refrigerator. What a piece of crap!! I am using my time to write this review as the repairman fixes the latest problem. I dont have much hope because he asked for my assistance and is sighing and grunting over there. I had the traditional puddle of water to start. Tray underneath was cracked. Was actually fixed. Water and ice taste like crap. They said its my city water... ok whatever. No good ice and water - we will survive. The food in fridge was freezing on the low. Guy just announced he broke the new thermostat... Yes, the thermostat broke after a year. Will get it fixed, hopefully enough to hold up until I can find another new refrigerator to buy. Never a Whirlpool or any of their other companies. Time to do more homework. So glad for these forums. Ugh!!

On the 27th March 2012 I bought a new Whirlpool 6th Sense washing machine S/N 411048002028 AWOE 9210 - 30 9Kg for E499.00. I brought it home and plumbed it adding in a lime filter on the water line to protect it from limescale. On the 14th September 2016 a service technician replaced the entire drum as the old one made so much noise and the ball bearings are part of the drum. On the 7th June 2013 a technician replaced the drive belt claiming that it moved if a light load was put into the machine. On the same day I added an extension of 3 years Guarantee at Euro 89.00. On the 14th October 2013 a technician examined the machine for a water leak but found nothing and charged me for the call. Out E25.00. I lived with the noise of the spin cycle ever since. The noise got steadily worse until 27th September 2016 when the machine finally packed in. I stripped the machine down to find the ball bearings on the drum completely rusted over so the drum was rotating without the cushioning. On the same day I bought a Bosch machine and decided to forget about the extra guarantee as the offending parts had already been replaced once and did not even last 4 years. I will bring it to the recycling yard later today as that is all it is good for. It was bought in Media World, Orio Center, Bergamo. It was paid for by Gianni ** who is my father-in-law and had a loyalty card for the shop.

I purchased Whirlpool washer in 12/2011. Immediately, I noticed the noise and called service. It was a whistling noise. The clerk told me nothing was in the manual and it would cost $65 to have a tech come out. He advised me to wait until it was louder and more consistent. I called again when it was. Gear case was replaced on 5/2/2012 five months after purchasing the machine. I called Whirlpool again in 5/2013 - same problem. I was told the diagnostic call would be $95, labor which is extended for a major job is $85 and the part would be $290. It would cost $470 to repair as the gear case was guaranteed for only three months. This machine is a lemon since the gear case is now shot again prior to the machine being 1-1/2 yrs. old. I called Whirlpool and spoke to Amy (Esc. Sup.) who advised they would replace the part only. The appointment was scheduled; the tech came, did diagnostics reading a manual and said the gear case is shot. I inquired, Well, you are going to fix it today right? The reply was, Oh no, it has to be ordered and its a two-man job. When I arranged for this appointment, this was clearly explained and what I was expecting, two men and the part to be replaced with them. Now its a five-day wait to get the part and then a scheduling issue when they could do it. This machine is a lemon and Id like to have the machine replaced or my money refunded. This is a runaround, scheduling the appointment and having someone show up with the manual and having no parts and not knowing that it was the part which broke again from previously being replaced.

In 2007, I purchased two 30 gal. Whirlpool Flame Lock water heaters (Model: FG1F3030T3NOV) from Lowes for two different homes that I own. I started having trouble with one of them after about two months. I replaced the thermocouple several times, with each one working only about a month. After that, Lowes replaced the complete burner assembly and that, so far, fixed the problem.Now, the second one has (1 Oct 11) gone out. The local Lowes told me that they are out of the burner assembly for this water heater. I called them this evening and was told that they didnt know when they would have the part, but to call back about every other day to see if they had received the burner assembly for this water heater. They said that it could be from two days to two weeks before they may receive this part!In 2008, I also purchased a 40 gal. Whirlpool Flame Lock water heater (Model: BFG1F4034T3NOV) for my house and no problems so far. In 2007, I even recommended that a friend of mine purchase and install one of these in a home that he owned. He did. I helped him install it and it later had the same problems! I am now needing a water heater for my workshop. What can I buy thats dependable?

We have had our Cabrio for one year now and we found the agitation cycle to be loud but we have gotten used to it now. The thing we cannot get used to is the sour smell permeating from it. It smells like a dirty mop. Our washer and dryer are in a small laundry room so when we enter it to get to the garage or bathroom, the smell hits you like a ton of bricks. Stinky!!

I purchased my Whirlpool Double-Oven one year ago and couldnt wait to use my new oven. I was told it was so efficient because I could use the top oven for quick baking instead of heating the entire oven (plus I could set it at different temperature settings). About a month in, I cooked 2 pizzas side by side. The first one burnt to a crisp and the one right beside it was doughy on top and burnt on the bottom. Not thinking, I blamed the pizzas! I also blamed myself, thinking it was me not being used to the stove.A few weeks later, I baked cupcakes. About 15 minutes in, I smelled burning and the cupcakes were raw on top and burnt black on the bottom. I called Whirlpool and they sent a technician out and he replaced the circuit board/clock. Worked for a couple of weeks and then the burning began again. Called Whirlpool again - another technician came out and adjusted the temperature. Here I am again, had to call Whirlpool again.This stove has been so inconsistent and Im so tired of wasting food because of this stove. My 4-year old Whirlpool dryer also went out last week so needless to say, Im not very fond of Whirlpool right now! If you are planning on buying a Whirlpool product, buyer beware and I hope you have a lot of patience...

Do NOT buy the Whirlpool Cabrio washer...it doesnt actually wash your clothes! Most clothing still half dry after the wash (didnt get any water on them) and they are still smelling sweat after the wash! Also doesnt clean basic stains that others washers clean. Even if you add water manually to the washer to soak your clothes, the clothes on top wont be agitated at all, hence the reason the clothes are still dirty after a wash. Poorly engineered washer... its a lemon as it doesnt do what it is supposed to do (wash clothes). Biggest scam ever from Whirlpool and shouldnt be allowed to be sold to consumers anymore!

I purchase December 2019, I had my previous stove for 20 years and wanted a new fresh look. I purchased the stove during a Black Friday sale. Started having problems with the door not closing. Customer service hold time took days and hours of hold time. Took 3 weeks to repair. Now seeing and hearing sparking and its week before Thanksgiving NO STOVE AT ALL. DONT BUY!!!! What happens when warranty is over????

Bought the Cabrio washer dryer set back on 1-12-13 for my new home and thought it was a good purchase. Well now its March on 2017 and the washer has been slowly getting louder during spin cycle to the point where yup you guessed it the bearing is bad because on a cheap seal that suppose to keep water out. It just cost me just under $600 to get the repair done and from reading other reviews and the fact that I have worked on cars and machines at my employment this will happen again. I wanted to save money on water for the city that I live in charges gold prices per cubic units of water but for the price of repairs to the water saved I am in the red. So once it goes again going back to conventional unit and will never buy anything from this company again. I work in the second largest printing company in the world for 28 years on press and know a bit about quality workmanship. Its really sort of typical on how over the years some good manufacturers cut quality and design in planned obsolescence into their product just to make money for the useless corporate bloat that has taken over. I made the mistake in buying what I thought was a good product from a great company but they just proved me wrong. People do not buy any products from this manufacture and find out what other unit they make and steer away from them too.

Does not clean clothes as well as I was told it would. Very dissatisfied with the price and performance and would not recommend this brand to family members as well as friends. With the way the current economy is, companies like Whirlpool should reduce their prices!

We have these appliances in our apartment. Its a gas range with a microwave over the hood. We did have the microwave replace a year ago, we have been here for 5.5 years. Its a good stove, we would consider buying one for ourselves.

We bought this refrigerator because it was the only panel ready one we could find. When it was delivered the two doors did not line up. There was an adjustment that could be made but it required that Whirlpool had to do it. We made an appointment and was told it would cost $179 for the adjustment!! This for a refrigerator we had just purchased for several thousand dollars. The service person showed up and after working on the refrigerator he could not balance the doors. He blamed it on uneven floor, misaligned cabinets – anything he could say to shift the blame from Whirlpool. We called and complained again. They sent out another service person. He was just as useless as the first one. Told us to even out the doors we would need to shim the refrigerator which he would not do. Complained to Whirlpool with no results. Finally hired someone not affiliated with Whirlpool who was able to get the doors to be aligned. Never Never buy a Whirlpool/Kitchen Aid Appliance. They do not stand behind their products and do not care about their customers!!

I have a Whirlpool cabrio washer (Model: wtw6300 Serial Number: CT3573525) and I am very disappointed with it. The spin cycle is the worst--sounds like a jet engine and gives me the UL error message of unbalance load. The machine was purchased in 2007 but was kept indoors. At the beginning, I didnt care because I had warranty with BrandsMart. I had to call at least four times. But now, I bought the automatic control and it didnt work. For two days, I was trying to balance this machine but it is impossible since the beginning.I contacted customer service and they advised me to contact the repair service in my area to get a diagnostic analysis of the issue. Hello! I already know what the problem is after reading all these reviews! I cannot tell you how pissed off I am. I will never purchase anything Whirlpool. Two of the gas burners of my Whirlpool kitchen, after two years of use, are no longer working. I will definitely contact BBB as soon as possible. Come on, fellow complainants, let us continue to fight to get a possible recall soon! We all have the same problem because this is a manufacturing defect!

The ice maker freezes up at least once a week. It requires removing the bin and chiseling the ice away. We have had repair here twice, and it still happens all the time.

I have been TRYING replace a damaged panel on a $10,000.00 Jenn-Air refrigerator for over 10 months now!! Whirlpool is the supplier of Jenn-Air - I have probably spent at least 3 HOURS on the phone talking with one rep after another who ASSURES me they will deal with my problem!! Last week I gave my credit card # to the rep - who told me my part was sitting there, waiting for my # to be shipped. When I asked why no one had called me to let me know, especially considering the amount of time I have been waiting - she said she didnt know. One week later, I call AGAIN to find out why my credit card does not show the payment. Only this time to talk to a fellow who says my part is still on backorder, and they used my card # to put a $1.00 charge against it - to hold it for when my part arrives.. BUT has NO IDEA when that may be! I feel Angry, totally discouraged, lied to, and used! I will NEVER purchase any appliances under the Whirlpool affiliate. This is abhorrent customer service - a $10,000.00 appliance and this is how it is dealt with!!! Bad, very bad!!

It gets the job done. Its no power washer, but the dishes get pretty clean and dry nicely. I have no idea how dirty the dishes can be and still get cleaned, since Im weird and pre-wash my dishes. Its stainless steel and black, and has quite a few wash and dry settings, including an option for heated or unheated dry. The utensil rack is attached to the door of the washer and cant be moved. Two levels, and pretty easy to do dish tetris with. No offense to most standard dishwashers – I need a washer about 3 times the normal size due to a passion for cooking. Its slick and matches my ultra-modern, borderline-Swedish interior.

Whirlpool Gold model WRS526SIAHOO - We purchased this refrigerator 10/2013 with all the matching appliances when we remodeled the kitchen. We moved our 1997 GE refrigerator into the garage. Now the computer board has gone out in the Whirlpool and we are back to using the 97 GE. The technician told me that he sees a lot of these boards going bad.

I purchased both the Cabrio washer and dryer because my dryer stopped working, it was old, and I knew that soon the washer would too, and wanted to modernize my set -- it was my moms old set. I was thrilled to get it delivered and should have had the delivery man from Lowes take it right back, when he told me they had just come from picking up one from another lady who was thoroughly dissatisfied with hers.Well, it didnt take too many washings for me to understand why that lady was upset! I really wish I had done the same thing! EVERY load of dark clothes have to be wiped off to get off the disgusting wet lint thats all over the clothes! Thats been going on since DAY 1! In every load, the clothes do not get completely wet and I thought I had combated that issue by having a pitcher of water always available to pour onto the load, so the sensor will add more water... That doesnt work, I now see!!! I just noticed last night lots of wet lint was on my fabric shower curtain liner, and I was thoroughly upset! I just never feel as though anything I wash gets clean. I truly wish I had come across this site BEFORE I purchased my set, and I would never have done so. Is there ANYTHING that can be done for people who have purchased these horrible appliances?

This washing machine has been nothing but a problem from the beginning. Theres always something wrong with it. Things that cost so much should last much longer than a couple of years! I have to clean out the drain about every 3rd time I use it or it wont spin out as well.

I dont know the model you have but this exactly what I just had happen in May. Its what they call the jazz board that is behind the light area inside the front of the refrigerator, where the light bulb goes. This is a circuit board and it seems when connection arent happening properly the fridge wont go into defrost mode and the water freezes over the evaporator not allowing any cold air to the top but working cooling freezer and making lots of frost too. I paid $400 to Sears service repair. The jazz board itself, I kept the old one and you can buy it online for about $100 and a child can do the labor that I paid hundreds for because, like you, I didnt know what the problem was. It takes less than 1 min to do this. I was furious! I hope this helps you and I too will never buy a Whirlpool. I found this site looking for why the refrigerator is making very loud noises, very loud banging, clicking, humming. Its ridiculous!

We have had this dishwasher since 1983 and we still run it on an average of 6 days a week. Features are the fact that it has given all of our dishes, our silverware, our pots and pans sparkling clean looks for all those years. It fits nicely into the kitchen space which was designed for a dishwasher. It never needed a repair. After all those years, this machine still looks fine. After all those years I really doubt if it still has a warranty and it never needed service.

House is 3 years old, builder put in all new Whirlpool appliances... first 2 years dishwasher leaked causing 18k in water damages... now the microwave just went out. BUYER BEWARE... DONT BY ANY OF WHIRLPOOL PRODUCTS POO-POO-POO. Unfortunately none of our products were still under warranty, since they were over a year old at the time they broke down. NEVER BUY FROM AGAIN!!! SHAMEFUL COMPANY!!!

I have not had any problems with my Whirlpool refrigerator. It is four years old and has had two owners, including myself. It has the stainless steel look and has top to bottom french doors, one side is the freezer and the other the refrigerator. Both sides are equally the same size. It has a filtered water dispenser and ice maker in the door. Id say for the price it is a really good value.

I purchased a Whirlpool (Cabrio) Washer on March 1 2018. I previously had a Roper top loader with an agitator that was 22 years old. I used that washer for that many years and washed clothes 6 out of the 7 days of the week. Probably at least 20 loads a week. I never had a problem with it getting my clothes wet & clean. It never left them dirtier after washing them than they were before washing them. I am so disappointed in this washer!!! I can see it will not do any good to complain to Whirlpool because apparently they dont care about their customers. They think theyre products are perfect when they are far from it. I plainly told the associate I wash clothes every day. Really dirt clothes. (My son is a mechanic). I need a good washer. I can wash them by hand better than this washer does. I am very thankful I have not paid the full price for this washer yet. I will be calling them to come pick it up when my next payment is due. I will be going to one of the local consignment or thrift stores and purchasing myself an old timey top loader washer with an agitator for $100 or less. Whirlpool I had high hopes with this product and would have been buying a dryer to match soon but I believe I will stick to my Roper products or anything other than Whirlpool.

We purchased a Whirlpool Accubake Drop-in Stove (Model # RS675PXG015) on 10/21/2006 from Lowes Companies, which cost $1,100.00. In 11/2012, we had an error message E1-F2, and we tried everything to get it to clear - all suggestions given by electrical repairman who does repair for Lowes Cos. The stove is porcelain, which also has problems of staining that cant be cleaned. We were told the repair would cost $200 for the panel, and if that doesnt work, another $400 for the other panel. In reviewing other complaints for this Whirlpool stove, there are enough complaints to recall this item or at least give deep cuts for the parts to repair this stove. We have purchased other Whirlpool items, and this one is not well made and too costly to repair. It should last at least 15 years or more. Cant Whirlpool do something about this obvious problem?

WRF989SDAF 29 Cu. Ft.. Weve had nothing but problems from this refrigerator. Water filter stopped working after 3 months. At one year, the left corner froze over and created a big bulge and repairman said it was a recall for a part and he had to completely dismantle the left side of the refrigerator. At one year 3 months, the ice maker started leaking water and all the ice melted and ruined our hardwood floors while we were on vacation. At one year 6 months, the freezer stopped working and we had to throw out hundreds of dollars in food. Along with the freezer stopping, the ice maker stopped as well and the water dispenser starting leaking again. What a nightmare this refrigerator has been!

We built 8 years ago, with ALL new appliances...All Whirlpool Gold...been very unsatisfied with ALL appliances... Had to replace range and parts for refrigerator..And extendend warranties all nonusable..We live NM off a tarred county road by 1/4 mile...no one wants to even come and look. Not good.

I absolutely HATE my Cabrio washer/dryer. I cannot get the mold smell out of my clothes. The clothes come out dirty and smelly. I have no idea what to do about it. It was a huge sacrifice to purchase these and a complete waste of my money. Whirlpool - please stand behind your products and take it back! Worst purchase Ive made in years.

Buyers beware! I have had the Cabrio top loader washing machine for less than 18 months and it is already giving me problems. During the wash cycle, it sounds as though the gears are grinding to the point it wakes my family up two floors up! The spin cycle is a joke. The washer sounds as though it is going to spin off into another room! When I called Whirlpool, they told me to shut the circuit breaker. That might reset the computer. No go which I figured as much. I have had washers that lasted 10 plus years with no problems. It is not worth your time or your money. Never again, Whirlpool!

Whirlpool has electronic controls allowing exact temperature settings. It is an excellent range and it has a storage drawer under the oven for storage of pots and pans. It also has sealed burners so no gunk gets under the burners.

Dishwasher (WDT710PAYM5) handle on the left side loosened within 2 weeks of purchase. Today the handle fell completely off. The dishwasher will be a year old in August of this year. I cannot figure out how to reattach the handle and there is nothing I can find in the owners manual to help me. There are only two of us and I am the one who uses the dishwasher. This should not have happened. Not real impressed with this machine.

I agree with the comments already made. My crisper drawer plastic rectangular piece just literally decomposed! It shredded into little pieces and cracked and broke, dropping one side of the draw set. I called about it - nope, not under warranty - replacement cost? Merely $150 so my drawers could be in the refrigerator. Also, because of the stress of the angle the drawer holder was when it broke, it cracked the drawer at the back - and the drawer had one grapefruit in it at the time. (Not considering replacing - cant imagine what that would cost when the little brace piece approx 14 was so expensive.) The flap - yeah, it split. I am a single person, no kids EVER in my refrigerator and I travel so much that I am barely home 20% of my days. The refrigerator gets very little activity opening and closing the doors yet the flap sliced. HOW DOES THAT HAPPEN??? With any break in the seal as they called it, the refrigerator starts collecting moisture inside (and I live in the desert so we have very little moisture in our air) and drips or starts causing frost build up on the icemaker. Yesterday, once again, the icemaker stopped working. When I asked about replacing the flap I was told the entire seal needed to be replaced @ the cost of $232 PER DOOR!! Right now with just the plastic rectangular piece and the bar between the two drawers (BTW the rollers on the frame are not included with the frame purchase they announced) I have $614 in repair parts WITHOUT fixing the icemaker! Last night water was running in my refrigerator from the icemaker. I WILL NEVER BUY OR RECOMMEND WHIRLPOOL TO ANYONE EVER AGAIN. I have been a Whirlpool ONLY customer for over 45 years!!!! They told me that I had to schedule an appointment with a service person at a minimum of $100 cost to me - JUST TO FILE A COMPLAINT with Whirlpool! They only take complaints from service people submissions. I advised the Whirlpool representative to start looking for another job because if this was the way they treated lifelong customers, her job may be eliminated due to No Customers! Does Whirlpool seriously NOT CARE about their customers? #WhirlpoolSux #WhirlpoolRefrigeratorsAreMoneyPits #WhirlpoolDoesntWantCustomers #WhirlpoolDeservesToGoOutOfBusiness #DontBuyWhirlpool #WhirlpoolFrenchDoorRefrigeratorsHorrible #NoServiceFromWhirlpool #WhirlpoolDoesntStandBehindProducts

Its a very well build dishwasher. Its quiet, really do a deep cleaning and make it easier to leave the kitchen clean after dinner with 2 kids its something that I need, Its not pricey either like other brands.

First three months, the main water gasket broke. Thank you for lots of water all over the kitchen. I pulled the washer out to inspect the cause, wanted to see if it was house plumbing or dishwasher. The hose was hanging off the bottom of the machine. During the 45-minute call, I got in my car and drove to plumbing supply and applied a new hose clamp. The next day, a free service call, the repairman said it was the second one this week, Thats just what I would have done, but would not put the machine back. (void the warranty, finish work, etc...not sure how he would have serviced the machine if I did not pull it out for him). A few months later the wheels on the top shelves give way/fall off the rack, so we have those replaced. As soon as one is replaced, the other side falls off... Now, approximately 14 months into installation, the dishwasher does not work. The control panel is flashing and will not start. What a runaround with KitchenAid. We were told there was a recall on the hose clamp (we never got one). We cannot have the control panel worked on until the hose clamp is certified... That will take a week. Then we can call back... What a hassle. We bought this expensive product on good reviews. We are most disappointed. There is very little concern for making the product good. Its incredible that so much can go wrong in such a short time of limited use. Once/day... The hose clamp is just poor engineering. The rest is terrible quality and support

Updated on 02/13/2021: Company fails on customer service. My stove’s trim is rubbing off on my Whirlpool stove only 6 months old. No chemicals were ever used to clean the surface. This trim piece surrounds the controls and is not covered under warranty. An expensive cheaply made stove. Multiple attempts to have the piece replaced got nowhere. A letter sent to the head office was deferred back to customer service. Whirlpool has lost credibility and I will no longer buy their products.Original Review: So disappointed to find the paint finish coming off the trim on my 8 month old Whirlpool range. No harsh cleaning chemicals were used. Only mild dish soap and a microfiber towel. The trim, attached to the control panel on the front of the stove, is not actually stainless steel, but painted to look like stainless steel. Whirlpool warranty doesnt cover esthetics and refused to replace the trim, stating replacement would include the entire control panel and it is not covered under warranty. So be prepared to have your new expensive stove look old in a matter of months.

I purchased my Whirlpool refrigerator from Best Buy 11/20/19. It has been nothing but a nightmare. It freezes up and defrosts into the refrigerator.! I called Whirlpool about the situation. The company they use to fix my fridge S&S Appliance has not been keeping accurate records. I have all the calls from Best Buy and S&S Appliance. I was told today-all my records didn’t count. Best Buy Geek Squad couldn’t repair so they turned everything over to Whirlpool. So about every week someone comes out and fiddles with it and tell me it is fine. 2 days later the same. I have owned many Whirlpool products and never have I been so disappointed. Their service has been neglecting and I don’t know how anyone would want to buy Whirlpool. They have set me up another service appointment with S&S Appliance. Obviously I have bought a lemon and no one takes any responsibility. Good luck with Whirlpool!!

Bought a dryer (wgd9050xw) 3 years ago. We bought a more expensive one than we had originally picked out. Every year its had to have a repair of same part. First year it was under warranty which tried to bill me so I had to dispute the charge. Charge was finally dropped. We just had it fixed again for third time in 3 years. Its a fire hazard because belt wears a pulley and basically melts it and gets belt hot. I just contacted Whirlpool and awaiting response.

I have purchased 2 Whirlpool washers in the past 6 years. Both have been a huge disappointment in quality and dependability. The 2nd washer I bought May 8, 2015 had problems from the initial purchase. In just a little over 2 years I have had to replace the suspension rods, and now the transmission is broken. Both washers had transmission problems. I have bought my last Whirlpool products. I recommend persons considering buying a Whirlpool product check the reviews before you purchase! I cannot believe this company continues to survive.

Whirlpool Dishwasher Model WDT7820PADMO was installed last October. Small parts began detaching themselves from the first day. Then machine leaked onto floor two weeks ago and I shut it down. As it was purchased from Sears, they and Whirlpool have batted responsibility for repairs back and forth until proof of extended warranty was supplied to Whirlpool. They then scheduled a repair job for a week later with an unqualified technician, who naturally refused the job. Upon callback, I was rescheduled for a day two weeks hence. As it turned out, the repairman would not be near my home on the appointment date. Luckily, I tried to move the appointment up, as the repair service said Whirlpool did not supply proof of the extended warranty. I saved five days waiting time by rescheduling, but have to supply proof of extended warranty yet again. All this for a dishwasher that takes three hours per load, and doesnt do a particularly good job of cleaning.

I bought a dishwasher Gold Series Top Control Whirlpool dishwasher at the Home Depot, April 4, 2015. Paid six hundred ten dollars and twenty-eight cents $610. 28. I noticed soon after that the top shelf falls off the rack when loading at front. I began loading from the back. It worked for a while but now it totally fall apart. The door will not close and I am unable to use the machine.

It does not clean as well as I would like. I have to wash the dishes before I put them in the dishwasher. It is also much too noisy for my liking. It has the pot wash and the dish wash. It has several types of cycles, long - short and it has a drying mode. My next dishwasher will be bigger so I do not have to run it every day. My next will be stainless. This particular dishwasher is nothing special but I have my eye on one with the buttons in the top of the door so nothing is visible on the surface. My dishwasher is getting older and I will replace it soon.

Only problem is you have to open door to access functions. 30 second increments and stop are on outside. Beautiful to look at and inside is easy to clean. 4 fan levels, vent inside or outside. 2 light settings. Nice and bright. Low profile over stove but big enough to hold large casseroles.

Thermal couple went out and nobody has one. You have to get it from whirlpool. This could be a easy fix with buying a $6.00 thermal couple but the one on mine has left handed threads. I took it to several parts places and they all said you have to buy it from whirlpool so you have to call the 1 800 number and they ask you how soon do you want it, 5 to 6 days to take a shower for $10 shipping, or $20 for 3 to 4 days without a shower or $32 for overnight? This ** should be free if they are the only ones that have it. I never heard of this crap before. The funny thing is they told me I should replace my water heater since the warranty is expired. Dont worry I will buy a new one someday and it will be anything but a whirlpool. I will never buy anything whirlpool again and make sure my family never buys whirlpool.

Right from the start of buying a new suite of Whirlpool appliances, the light over the range burnt out. We figured it was just a bad bulb so we replaced it. Soon it burnt out again, replaced it again, then again it burnt out. I finally called Whirlpool about the problem and found out it is the electronic panel that needs to be replaced... Of course at a full charge to me! I am so over WhirlPoo, (yes I spelled it that way on purpose) every single appliance has had issues. I have just lived without a light over my range because fixing it is more expensive than buying a whole new microwave. Never again will I buy any WhirlPoo appliance!

The duet washer is just over one year old and started showing F25 code on screen. It had been making a really loud noise in the spin cycle. Last week, a really loud noise and then the loads wouldnt be spun. There was a puddle of water on the floor near the machine. We had a repairman out today and he stated that theyre repairing these machines all the time. He stated it was the bearing and that theyd been told that Whirlpool had installed bad bearing from a different supplier. I called the Whirlpool experience and after 4 minutes and 19 seconds, I actually spoke with a service rep. She said since my machine is less than one month over the one year warranty, Id have to call the extended warranty people. I asked for a supervisor and after 2 minutes and 38 seconds, she came in line and wouldnt budge from her story. They also stated that there are no service issues with this model washer. Extremely poor attitude and Whirlpool is doing everyone, whoever purchased a duet washer, a terrible job on these washers. At least, Ive now found out that there are a lot of other folks out there with the same problem. We need to get some attorneys to start a class action just like the mold/smell customers did already. Sad, sad day for Whirlpool as Id been a customer all my life.

I am very upset about this Washing Machine and Dryer. I did my research in 2012 and found good reviews on drum size, water usage, bells and whistles. I purchased the set in Feb of 2013 (its on Jan of 2017). NOT EVEN 3 years later, I write to say that my washing Machine is ready for replacement! I paid 989.00 for each and last year the Spring on the Glass Top was worn away, I am told because bleach was splashing up in the spring area. Cost to fix with a local repairman... $235.00. Now I noticed a small amount of water on the floor, move the washer and there is a LARGE amount of water Stain and my cycles keep popping up UL. Two separate repairmen (because I didnt believe my trusted first one) tell me the cost for the shot bearings and seals will cost almost as much as a new washer! I am a family of 3. I have a daycare so do a few extra loads, but am not using this any more than average to low use. Not to mention that on top of all of this the computer appears to be shorting out and to order a new panel the repairman places that at an EXTRA 300.00. SO UPSET! The dryer dries very nicely and is quiet however, the motor went out 6 months ago and we replaced that, not wanting to but better fix than scrapping it only 3 years into a product expected to last well over 10! The little clip on the door to lock it is also loose and hardly locks now. The repairman is having trouble even finding the small part. Young Couple Expecting to have a brand new 1900.00 washer dryer set last a long time only to be out of warranty and already needing to buy a new set! DONT EVER BUY A CABRIO WHIRLPOOL.

I purchased the Energy Smart Gas Water Heater about a year and a half ago, intending to install right away as part of our upgrades. Just now, I was able to install this replacement to our 30-year-old water heater that was showing problems. When trying to start the unit, I kept getting the response that the lower sensor unit failed. We contacted plumbing companies. We were told they would not work on any Whirlpool models purchased from Lowe’s, because they were the worst hot water heater ever made. I called Whirlpool support. They wouldnt put me through to a tech support person until I was registered in the system. I gave up trying after many minutes of frustration.

Awful customer service. We bought a washing machine in 2010 and it has shredded a ton of clothes over the years. I called customer service to see what they could do to help me with this problem. After about 45 minutes of trying to get more than a service that I would have to be responsible for, the supervisor offered me a new washer at a discounted price. I went online to compare and found out I could purchase the exact same washing machine at home depot & best buy for $50 cheaper. I called back to see if there was anything they could have done and they would not budge.Shame on you Whirlpool. You have lost a customer and I will make sure no one I know buys one of your products ever again. I cannot believe that you would not make any accommodations for us. We bought that washing machine with the intention of keeping it for 15 years. It has cost us countless amounts of blankets, shirts, pants, etc. I cant believe you wouldnt help us after all the money this piece of junk cost us.

Purchased a Whirlpool microwave for new home in December 2013. Model WHM31017AW-1. This is the second time the heater element has to be replaced. Im starting to learn the warning signals: open door and then a short time later the microwave would die a sudden death. In my 20s I purchased for my house in Boca Raton Fl all Whirlpool products... they worked forever. Now not so much. In order to get this one fixed again, I had to get a service contract for $300 which would be cheaper than getting it fixed again, heating element $400 and service call another $100. Serious $300 service contract money too much for a senior citizen. Never will I buy another Whirlpool product as a result.

Overall??? Ive owned this Whirlpool side-by-side refrigerator for a year now. Love it except for semiannual cost to replace the filter. My brother recently installed the same model in his motorcoach. Yes I recommend this appliance.???

I purchased a matching set Whirlpool Cabrio top load washer and dryer in 2007. Bought from Conns for $2,100. After 3 months of ownership, the circuit board had to be replaced on the washer. Three months later the heating element was replaced on the dryer. Just recently I spent $350.00 to replace 4 drum suspensions. The washer literally shook my home. 3 weeks later, the circuit board needs replacement (code F1). Estimate to repair - $325.00. The dryer is not working properly. Im having to run the clothing thru 2 cycles. Back to the washer. It shreds my towels. Ive read where other consumers have had this same problem. These are expensive towels. So, only 7 yrs. into ownership and I am replacing this junk with the old school washer/dryer. Unlike the Cabrio washer, I will have a washer with an agitator that will actually clean my clothing. Whirlpool manufactures trash and the Cabrio duo was the worse purchase I have ever made. Do not purchase Whirlpool and definitely do not purchase Cabrio.

Model # WFG510S0AS1 SER #R30850040. Oven was installed NEW in the home I purchased in July of 2013. I used the cleaning feature on it in Nov 2014. I am amazed that it did not start a fire. Please see pictures attached. The whole control panel melted. This makes the oven unusable and extremely dangerous. I will need to replace the whole control panel. I followed the instructions completely in the manual provided for the cleaning cycle. It says in the manual to only clean the over this way as using easy off or any other cleaner will damage the inner surfaces.Whirlpool claims they have no knowledge of this problem but there are numerous complaints on their site about it as well as other internet sites complaining about the melting of the control panel. I need to know how to fix this problem and dont believe I should have to pay for something that is obviously a flaw in the materials used. It is extremely dangerous. Since these pieces of Whirlpool equipment were installed by the broker that originally purchased the home, I have no record of purchase. I can try and contact him and see if he has anything but kind of doubt he has receipts now.

I have Whirlpool 40 gallon heater 5 years ago. The pilot light went out and I replaced the parts. This has happened three times and I have replaced the entire thermocouple assembly three times. The last time, the parts came straight from Whirlpool. This time, the pilot light will not stay lit. I am on my way to buy another hot water heater for my family because I have had enough.

I have a whirlpool water heater. This is the third or 4th time that the upper sensor failure code has come on. Our water heater turns off all the time and we have to fire it back up. In the past few months, it has started pouring water out from the long tube on the side of it anytime we turn it on for more then 10 minutes. The last time we called a plumber, I was trying to get a quote on a tankless water heater. Ive been so fed up with ours and I thought that would be a better route to go. The plumber explained the negative sides to a tankless water heater and explained that our water heater was a really nice, really expensive and fairly newer model. I told him that I had just gotten it about four years ago. He said he could just fix that one. So after looking at it, he acted as if he didnt know what an upper sensor was and told me it was under warranty and that I should call for the parts. Every time we have called for the parts, they send the same box thing on the front of the heater and every time, it doesnt fix it for long before it says the same thing. And now, like I said, the water heater has now added the problem of pouring water out of it. I need help. I dont know what to do. Im tired of not knowing if Ill have hot water or if the water heater is going to pour out water. Im pregnant and worried that if we cant get this fixed Ill continue to have this problem along with having a baby to take care of. Please help.

My wife and I tried to buy a Whirlpool refrigerator and when dealing with their customer it seemed like the left hand didnt know what the right hand was doing. My wife and I were really disappointed being that these refrigerators are supposedly made in America; thats why we wanted a Whirlpool; but we would never buy a Whirlpool now because of the way we were treated also. Sincerely unhappy with our experience!

Ice maker kept freezing up. Im continually taking the ice tray out to unfreeze. The frequent removal of the tray eventually broke the tab off on the liner. Ive now been told this (liner) is not a replaceable part and since that is the case, the warranty will not cover. Im upset that the repair technician did not process the claim properly and state that the make had a problem freezing. What kind of company would manufacture a product that would have parts that are unrepairable? You spend close to $2,000 on a refrigerator, wouldnt you think you would have an ice maker that works? I know they hope to sell more appliances this way but you can bet I will not be purchasing another Whirlpool anything! I will also be retracting my recommendations to friends and family to purchase a Whirlpool. The company does not stand behind its products.

Contacted Whirlpool - unit (Cabrio washer 7600xt) is out of 12-mo warranty. Spoke with manager, Tracy **. She said they would not help - out of warranty. Called local parts/service center - ea. hinge is $42 plus shipping and labor to install. Obviously this is a defective design. The lid is too heavy. I was having a difficult time deciding to spend 150-200 dollars every 2-3 years for hinges on a $700 washer and then I read all the other complaints about Whirlpool washers. I will sell it for scrap and buy a better brand.

I have had my Cabrio set for two years only and the washer has a error code of F6 and E3... pretty much does not work properly and need to swap out main control board which is about 200-300 for the part. I’m very disappointed in this product for as much I have spent on it. My old school top loader lasted longer than this piece of junk! I believe the steam from the wash is going up into the control board and messing it all up! Water and electricity does not mix! Maybe they need to relook at their products. I want my money back!!!

I bought this piece of junk Whirlpool Cabrio washer two years ago and it’s been nothing but junk. Just like everyone else, this thing has never gotten my clothes clean no matter what I do. Anything with a drawstring or straps gets ripped up or stretched out. It’s loud and shakes, even though it’s leveled. Now, to top it off, it’s leaking water from the basket seal. I called Whirlpool and they couldnt give a damn. Since it’s out of warranty, it’s my problem, even though she said they know this machine has a lot of problems. So now Im stuck either fixing this thing or buying a new washer. Every appliance in my house is a Whirlpool and Ive had nothing but problems with several of them. I thought when I bought the brand it was a good brand and they stood behind their stuff. Boy, was I wrong! I will never buy Whirlpool again! They should recall this washer!

I am following up on a review I submitted on April 22, 2015 about a Whirlpool refrigerator with french doors and bottom refrigerator. At the time, paint was falling off from the door as pictured in the previous review. This another chapter on this story and probably the closing chapter. A few months after the paint event which I could have lived for a while, the right door hinge literally disintegrated leaving the door without support. The door seals material is of such poor quality that they have disintegrated and the water condenses inside. The bottom photo shows hinge components that came off the door hinge on the kitchen floor. The second photo from the bottom up photo shows how the door scraped the plastic of the freezer door top trim if the door is not lifted to clear it. The second photo from top to bottom shows the door over the hinge pin if I am not careful lifting the door to clear the freezer door.The first photo from top to bottom shows how the door remains open if not lifted so that the door magnetic seal keeps it in place. It is very hard for me to believe that a country like the United States of America treats its customers with no respect. I met my obligation to pay the amount on the price tag of this appliance but I cannot say that Whirlpool did its part of providing a basic quality product. There is no consumer protection agency in this country to protect consumers from corporate predators that have no sense of a fair deal with a customer. So here we are, being abused by United Corporations of America. I hope the future brings a different understanding of the american people on these matters. Thank you for the opportunity to express myself on this matter. Next step... buy a foreign made appliance that will support another country work force... sounds familiar.

I purchased this dishwasher (whirlpool WDF330PAHW2) in February 2019. Really worked great until May 2020. Now doesnt drain on the last cycle, smells bad (even though cleaned) and door leaks under handle on front. Really too bad. I have been a Whirlpool champion for 25 years. Now not so much.

KitchenAid double oven glass exploded during the self-clean cycle. The oven was purchased on 9-20-11 and the glass exploded on 11-30-11 during the first-use of the self-cleaning cycle. The cavity was damaged with dents and shards of glass from the explosion. Unfortunately, the warranty for KitchenAid is replacement of parts and repair only. Nicole, supervisor at Whirlpool, offered to extend the warranty 6 months. Then I was somehow disconnected from the call.

We purchased a Whirlpool fridge from Future Shop four years ago. It was delivered by professional movers and we plugged it in and smoke filled the house. We called Future Shop and very soon, another fridge arrived on the back of a pickup truck (no box or papers, etc.). This fridge is slowly ruining our kitchen floor as from time to time, we notice a puddle of water leaking from under the fridge. We called the store a few times but were told its normal for a fridge to do that in hot weather.

This piece of junk just broke down not even one year after the purchase. Every singe Whirlpool washing machine has broken one way or another. This one will set the wash time for 57 minutes, and exactly 24 minutes left in the cycler, you hear this big crash and then everything stops. Another dumb thing about this piece of crap is that when the problem happens, the POS keeps the lid locked so that you cant tell what the problem is. What morons would put a lock on the lid? Its not like someones going to take a jacuzzi bath!Restarted the POS again, and exactly 24 minutes left on the wash cycle, there was another crash. Both times, exactly 24 minutes. NEVER BUY FROM WHIRLPOOL!

I am in construction and have had to deal with failed motherboards on new Whirlpool fridges that we put in some rental properties. Knowing that, when I went to buy a fridge for my own house, I went to a very reputable appliance company and talked openly about getting a fridge that wasnt going to be a problem. My sales agent and I go back always and he was very open about the problems with the more gadgeted Whirlpools so we picked a low bells and whistles French door fridge to avoid that. It stopped cooling at about the same age as all the rental units did and had a control panel fail. The sales guy and I laughed about how even knowing about the issues I didnt avoid it. Their company came out and fixed it for just short of 300 bucks.Two months later, it stopped cooling again. The service tech came out and this time hit the side of the fridge with his hand and opened a relay getting it to work, at least for another week. The tech told his boss that I must not have shut the freezer causing it to go into defrost mode. The third time it failed, we were out of town and lost all our perishables. We had the same tech come out and replace the board he got to work the last time with a whack to the side of the unit. That board should have been under a parts warranty for 90 days but I may have missed that with the slap repair working for the additional 2 weeks.Im trying to put this behind me but Whirlpool sent me an Extended Warranty Plan opportunity. I can now buy a plan on an almost 3-year old fridge. I am wondering if they are trying to give me the hook up on a bad product or just hoping to prey off my fears and cash in. The company I bought the appliance from has been first rate but their hands are tied by Whirlpool who has virtually no support for their vendors. Before buying a Whirlpool, consider a Sub-Zero. After you figure in the repairs, they arent too far apart in price.

First time owner of a Whirlpool range and will be the last time. Nothing but junk! I liked how the top grates were and electronic ignition. The knobs turn too easy and often when bumped will turn gas on without igniting. Very dangerous. The oven grates guides rusted almost immediately making it difficult to pull racks out. The oven light works sometimes. The glass on the oven door at the bottom came unglued. The bottom door under oven is a total waste. No use for it. In my adult life I have had different brands but this is the absolute worst and will never recommend this brand to anyone period.

I have raised complaint regarding my refrigerator and changed compressor and they given me 1 year warranty but after 3 days again compressor gone and they have came and replaced that and taken service charge. Again after one month compressor giving problem and freeze is not getting defrost.. Again I called to customer care but again they want Visiting charge.. Really pathetic Service I ever seen. And customer care people does not know how to handle client and repeating same line. Dont buy anything from Whirlpool.. its worst service provider.

I am so unhappy with your product. Constantly have to restart machine. Never had a problem with my other washer. Takes forever to do laundry. Hate it.

I have had a terrible experience with fridge Whirlpool. Two fridges have been delivered to me in bad condition. The first one was aesthetically awful (looked old and used) and the freezer didnt work so it was exchanged. The second one works and it looks ok but it makes very loud noises all day every day. I live in an open concept condo and this fridge sounds like a train for more than an hour more than 5 times a day, it is terrible. I have been calling customer support for a solution and first of all, there are no technicians in my area, and since the fridge works as designed there is nothing to fix so Im stuck with a terrible noisy fridge that I hate and destroys my day which I paid a lot of money for thinking that the brand meant quality but it doesnt. Customer support doesnt respect the customer and their answer that the first works as designed makes me understand that Whirpool designs bad quality fridges. I have never heard a fridge making these noises, not even brands that are less named than Whirlpool. For your inner peace, I recommend you to stay away from Whirlpool-Maytag fridges... If the fridge is in bad condition (but working) youre going to be stuck with it. The brand doesnt really mean quality and support... it just means more expensive.

We bought a duet washer and dryer about 3 1/2 years ago. In that time, we had many error codes that we had to research online and fix. We have replaced many things to date. However, this last code,F70, has really been the last straw. Basically you are better off buying a new washer and staying away from Whirlpool. We had a company tech come and diagnose the washer. This code says that its the interface board. The company has replace this board 3 times and the code is still coming up. They have basically replaced everything in our washer and the code remains the same. Nothing is fixing it. They have had Whirlpool-certified employees come in to look at the washer and are unable to fix it as well. They have been trying to fix it for 2 months. I called Whirlpool corporate office and they informed me that the company that we went with is not Whirlpool-certified, therefore the only thing they will do is either give us 15 % of our money back if we were to by a new washer, or we can have a certified dealer come out and diagnose it again. Well, that is just a waste of time. We already know whats wrong with it and would have to pay again to have it diagnosed or we totally loose a lot of money. I feel that Whirlpool really should stand behind their products, considering the price tags they have on them. They should last much longer than 3 1/2 years. I will not by another Whirlpool product again. Apparently, Whirlpool doesnt seem to care about loosing customers. I dont feel that they deserve any stars but it doesnt allow to pick a negative number.