Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

I purchased a Gold Star Whirlpool Refrigerator from Sears which was installed on July 1, 2010. The freezer was icing up along seams, so sealant was used. However, now I noticed after 14 months that the interior refrigerators lining is fracturing throughout the sides and bottom of the refrigerator. Not at seams but all over fractures, spanning 10 to 3 to 2 on the bottom and side of the interior lining of the refrigerator.Sears answer is more sealant, and Whirlpool does not take any responsibility in designing a defective liner since it is pass the one year time frame. This causes your refrigerator to be on more often, because of the cracks. Unfortunately, the consumer loses out. Both representatives were nasty and when I asked for a supervisor from Whirlpool, an incident report was written, however I will not ever be able to get a copy of it. It will be considered an internal document. It is a great setup between Whirlpool and Sears having defective appliances made to last a year, and Sears to win with warranty agreements for the life of your appliance of $250, for one year coverage. When you buy the warranty and have a lemon, Sears doesnt replace it, My suggestion to consumers is to buy a tube of sealant.

Bought a Whirlpool refrigerator from Lowes 5 months ago. Already had a repairman out two times. The refrigerator is defrosting out on the floor. We are constantly having to change towels to catch the water. The last repairman said it could be fixed and started the procedure to get an exchange since it was still under warranty, but now Whirlpool is saying they still want to fix it even after we were told we were getting an exchange. These people are crooks and put out low quality merchandise, then dont back it up. I have seen complaint after complaint on the reviews. Whirlpool needs to be put out of business.

I would like to know if anyone else is having trouble with the broiler unit. The unit quit working. Thankfully I had purchased the extended warranty. The guy came out, cleaned the orifice and called it good. The next day I went to use it, and guess what, it did not work!! So we thought maybe we needed to leave the oven door cracked open a bit... Well, guess what... It melted two of my knobs!! We called, got another guy out here. He checked everything. Even pulled the stove out to check out connections. Then he informs us that you can set the broiler to whatever temp you want. Thats new. So again, we try the broiler.... Guess what... It got to the temp and clicked off. Now I ask, how does one broil a steak if it does that? I did call Whirlpool directly and got nothing. Our model is WFG361LVQ2. So please, if anyone out there knows that this is how it is supposed to be... please let me know.

I have the same lid closure issue expressed by many consumers and whirlpool refuses to acknowledge this as an issue, only recommends purchasing a new lid at $225. Lid design is flawed, metal L bracket connects to plastic housing/trim/side of lid, causing glass to pop out and stress cracks between screws. New models of same washer have redesigned lid, no cross reference part number or dimensions listed to determine if new lid will fit.

If 0 stars was an option, I would have chosen that. Ive had my own home for 34 years and have had many washing machines over the years. My Whirlpool Cabrio is absolutely the worst washer I have ever encountered. It doesnt get clothes clean and constantly gets out of balance. Whirlpool did a service call and said it is functioning as designed so I was unable to get a replacement. I really hate being wasteful and adding a huge appliance to a landfill but I will be replacing this machine as soon as it fits into my budget. I dont have a receipt to submit because it was purchased by my builder at my request. Do not buy this machine!

I received this Email from the Whirlpool Director of Consumer Care to evaluate my experience with their customer service department. I filled out the survey over a week ago including a complete documentation of my problems and have not even received an acknowledgment of the survey or promise to look into my problems.In the last 7 months I have experienced problems with 2 Whirlpool major appliances which both appear to be unrepairable and which have been unsuccessfully brought to the attention of your customer support group. In March a fridge and in October a clothes washer. Both were high end products roughly 3 to 4 years old. I did not have an extended warranty with the fridge so I dealt directly with the customer support group. However I was covered by warranty with the washer and your distributor Bad Boy have been making the calls on my behalf but have been just as disappointed to date as I was.Both cases were very similar. In both cases the repairman came out within a few days and promised to return the following week with the broken part but I have never heard from either one of them EVER. In the case of the fridge I was told to defrost it the day before the promised repair date and lost all the food $$$. At this stage a number of calls went out from me to Whirlpool for the fridge and from Bad Boy for the washer and eventually we both got a new delivery date of roughly one month. Both times the date passed with no shows and no call backs. Repeated calls later to the customer service group, with promises of EXPEDITING the delivery, the fridge part delivery date was extended to 3 months so we had no choice but to buy a new fridge. As for the washer, Bad Boy even had an unsuccessful face to face meeting with your representatives and we have had no word back or expected delivery dates well into the third month.I HAVE NO IDEA WHAT TO DO? I have made so many calls with so few call backs and no clue what to expect or when? Your representatives use the word expedite with no idea what the word means. At the suggestion of one of your representatives I even called one of your distributors Sears to see if they had the part. Their Canadian head office is in the Philippines and they said they had the same problem with Whirlpool. Twice I tried to talk with your representatives supervisor and both times were unsuccessful.In a world of computers where it should take seconds to find inventory parts and expediting packages usually refers to next day delivery, the fact Whirlpool requires months is unbelievable. The only explanations I can come up with is 1- You dont make parts for your appliances. 2- New appliances are made so poorly all parts are gone. 3- You could not care less about your customers. 4- You dont own a computer. Most of our appliances are Whirlpool because we thought you had a good reputation. We had to purchase a new fridge and still have had no word on the washer?

Ran Aqualift self cleaning cycle 4 times at 40 minutes and only bottom was cleaned, sides are still spotted and the rear wall still shows a heavy spotting. My stove is less than a year old. My prior stove with self clean at a higher heat was great, when done only had to wipe out!

Bought a whirlpool refrigerator in 2015, have had both handles replaced 3 times, the bottom pieces of the handles are made of plastic and they crack. We had to take them to a metal fabricator and have them replaced with metal to keep them from breaking. Lowes and whirlpool know of this problem and they do nothing about it. Will not buy another whirlpool product. Very dissatisfied.

Got this refrigerator when I old one of 10 years through AHS home warranty. I asked for a similar one to the one we had. Surprisingly we received the Whirlpool which turns out to 5 times better than are old GE. Same height and width but deeper and with more compartments. We are extremely happy with it

I have a Whirlpool Duet Steam Washer that will be two years old in September 2013. It has been making terrible, loud noises during the spin cycle for a few months now. Repair tech told me it was the bearings and very costly. It will cost me over half of the original cost to repair a less than two year old washer. This is my second Duet front loader from Whirlpool. The first one was a drum issue and the rod ended up snapping. Again, very costly so I bought a new one. I should have learned my lesson the first time. I do not agree with extended warranties and it is just an additional money maker for the manufacturer. They should be making the product so people do not have to purchase those. Anyway, back to the washer at hand. I refuse to spend that much on a newer washer and will never purchase a Whirlpool product again. I will let this thing bang for as long as it is going to last. Unfortunately have also just purchased the dryer that matches this washer since I still had the old model Duet Dryer, so kind of stuck with them. Spent an hour and a half yesterday on the phone talking to people at Whirlpool and they really dont care if you have an issue or not no matter how old your machine is. They just want you to have purchased the extended warranty or forget it. There should be a recall and they should be helping these customers who all seem to be having the same issue. Done with them!!

We purchased a Whirlpool Cabrio Washer Model WTW7340XW0 type 580 Serial C02770464 and a Whirlpool Cabrio Dryer Model WED7300XW0 Type DSSA-ELE-2406026-EL54 Ser M02717021 in 2010 for over $1,700. Included was a 3-yr anything goes wrong, well replace for free warranty. A month after the purchase, we lost our home and were forced to move. We put the new appliances in storage and they have been there ever since. From the day we purchased the washer, we never got a clean wash out of it. It seemed it used about a teaspoon of water. Clothes were never clean... We had many other problems at the time and both washer and dryer were put into storage.Today, the warranty has long expired and I happened to check on the ConsumerAffairs site to see if there were any comments regarding whirlpool Cabrio washers... WOW! 1600 negative comments and not one positive. Later, I realize we made a $1700 mistake. My question is do I have any recourse? Please advise.

I bought my Whirlpool washer/gas dryer 13 years ago and up till now I havent had one service call or repair done on either one of them. I have owned a Whirlpool washer/dryer before and I didnt have any problems with them either. When the time comes and I have to buy another set, there is no doubt in my mind that I purchase Whirlpool products again!

I had a Whirlpool GI7FVCXWY01. Purchase 3/13/2010. I had repairman after repairman come to fix it. The last one probably saved my family and my house. The light in the back corner was not only blinking, but flashing rapidly, much like some wild party light. It eventually stopped. The freezer works perfectly fine, the fridge works when it wants to. The ice maker makes ice some days but not others. The motor on the ice dispenser is completely frozen up. Does that all sound about right? If it does, clean it out and cut the power to it before someone gets electrocuted or your house catches fire.If you cant find the electrical diagram, or the company wants $455 to answer your questions, look under the right side of the freezer draw, but not on the draw. Remove the guard on the very bottom of the unit, near the wheels on the right side. You will feel a plastic bag attached to the underside. Inside that bag is the complete diagram of all the wiring harnesses along with the schematic for the amps and voltages for each wire. Are they telling your circuit board is bad and you will need a new one? Before you do that, inside the fridge compartment, in between the water filter and the ice maker, remove the light cover. Notice that inside that space is the access to another panel. Remove that panel. BE SURE THERE IS NO POWER RUNNING TO THE UNIT FIRST. Here you will find a connection plug with more or less 15 wires that are connected to the main wiring harness. Above that plug you will find a holding chamber. This holding chamber contains water from the filter that is waiting to go to the ice maker. It has dripped condensation on the plug since the day you first turned on your fridge. Your wires are most likely broken and corroded. You will need to have your unit completely rewired, but because of the design flaw that fix will only buy you another 4-5 years. My Whirlpool GI7FVCXWY01 left yesterday 5/15/2014 and none too soon.

We purchased a mid-grade Whirlpool Gold Series dishwasher a little over 2 years ago. 14 months in, the motor failed, requiring a $295.00 repair/replacement. That was nine months ago, and now the motor has failed again. That is outrageous! No more expensive repairs on this piece of junk. Its going to the scrap heap. We just ordered a Frigidaire. While I have no experience with that brand, it cant possibly be as bad as Whirlpool.

We purchased the Whirlpool Cabrio washer and dryer duet exclusive to Lowe’s in June 2011. I was immediately dissatisfied and went to Lowe’s. They told me I only had 7 days to return it. They dispatched a service man and he said it was working as it was intended to but I would never be satisfied. If I had dirty clothes from farming, construction, or mining, I should forget about it.” The washer is an eco-friendly model and all the clothes do not get wet. It wrings them out very tight and everything needs to be dried or ironed to get rid of the wrinkles. After 6 visits and lots of stress, I am returning the washer to Lowe’s and they will replace it with a different model. It definitely will not be a Whirlpool. I am very disappointed in the service and response I received from Lowes.

I purchased a Whirlpool fridge (model GX2SHBXVQOO) on November 27, 2010 and it leaks water on my floor. I have to keep a towel there or it runs all over. I also purchased a Whirlpool range (model YGFE461LVQ) and the convection fan went on it a month after we bought it. The manufactures warranty does not allow repair people to travel any further than 100 km to repair, something that we had to take the stove in to be repaired. We got the stove back the same day and brought it home. Low and behold, after a short period of time it started to rattle again and got steadily worse. Also, now my one burner on high does not stay on high; it keeps going out then coming back on.I have called the place we purchased these pieces of junk from and they said there is nothing they can do. I also sent e-mails to Whirlpool and they said they will look into it and get back to me. That was months ago. I called Whirlpool and was basically told that there was nothing they can do, that I was to call the repairman. Never, never, ever buy a Whirlpool product.

I bought a semi automatic washing machine from Croma Store (Gurgaon) on 03/09/12 Model no A-72H* and I regret to say that the water direction changing knob (to change water flow from agitator to dryer), has broken. The machine is not even 4 months old and the water inlet is broken. How can this happen in a brand new washing machine? You claim to have durable home appliances products and your machine does not last 6 months? Can you see that the broken piece is attended to or replaced at the earliest?

I purchased a home from Pulte and closed in June of 2020 and had no choice but to take Whirlpool appliances. Pulte does not offer high end appliances in order to maximize their profit. The first thing that failed after only 3 months was the Microwave and because we didnt want to get the same cheap microwave we upgraded and paid 400 for a Kitchen Aid, same size but never received the trim kit that matches the oven that came in sometime in October 2020. It is now January 2022 and we are still waiting for the trim kit. Every time we call to find out we spend hours on the phone.The refrigerator is a cheap version of the worst refrigerator made in China, the ice maker works ok but ice gets stuck in the chute and when it doesnt get stuck half goes to the glass and the other half to the floor. Poor design and we are stuck with it. Tried to buy an LG from Costco but it wont go through the door so again we are stuck with this small refrigerator with no room for groceries for two people. Stovetop is also cheap, only looks good the day we got the house, one of the burners would go off when turned to low with gas still flowing. Grates look 10 years old but must admit we cook every day. Oven will not calibrate and it is not accurate so we have learned to set everything 10 degrees higher to make up for the variance. Dishwasher had issues as well, unless you run it for 3 hours the shorter settings always have dishes or utensils still soiled. Warranties have expired after one year so it is now time to replace almost everything if we want decent appliances. Very disappointed but I blame Pulte for buying cheap.

There is almost NOTHING I like about my new $1000 Whirlpool Cabrio Platinum washing machine! The clothes dont get clean. Stains become PERMANENT because clothes are spun and matted so tightly together, the 2 inches of water allowed into the tub cant dissolve them. Fabric softener stays a gummy substance because it has to be SUCKED out of the dispenser, not sprinkled out with water. I pin socks together to keep them in pairs, but this machine rips them apart and the safety pin end up in the bottom. My bathroom rugs are shredded. You cant add an extra item if you need to, because the tiny portion of water leaks out. There were DRY spots still on the sheets at the end of a cycle. This machine is an engineering nightmare, sort of like the Edsel. The only action programmed to clean the clothes is a wiggling motion on the floor of the tub. The tub spins so much, energy goes through the roof. Man was given 3 survival elements to assure our existence on earth: water, air, and food. Why are engineers trying to faze out our use of water? This machine has dazzling looks, but NOTHING else. I am so sorry I didnt read all the reviews first. Who would ever think the environmentalists would inflict such pain on our basic domestic obligations! If I dont get my money back or a decent exchange at Sears where we bought it, Im taking the machine to their parking lot and commencing a show with a baseball bat.

After just 2 years, the electronic control board failed. The temperatures are stuck on the coldest/high mode for both the freezer and the refrigerator, spoiling some foods. The parts and repair are going to be $300. Whirlpool will not replace the defective part or pay for any repairs. Shame on Whirlpool! Model No. GB2FHDYWQ01.

In 2007, I purchased two 30 gal. Whirlpool Flame Lock water heaters (Model: FG1F3030T3NOV) from Lowes for two different homes that I own. I started having trouble with one of them after about two months. I replaced the thermocouple several times, with each one working only about a month. After that, Lowes replaced the complete burner assembly and that, so far, fixed the problem.Now, the second one has (1 Oct 11) gone out. The local Lowes told me that they are out of the burner assembly for this water heater. I called them this evening and was told that they didnt know when they would have the part, but to call back about every other day to see if they had received the burner assembly for this water heater. They said that it could be from two days to two weeks before they may receive this part!In 2008, I also purchased a 40 gal. Whirlpool Flame Lock water heater (Model: BFG1F4034T3NOV) for my house and no problems so far. In 2007, I even recommended that a friend of mine purchase and install one of these in a home that he owned. He did. I helped him install it and it later had the same problems! I am now needing a water heater for my workshop. What can I buy thats dependable?

I had a Whirlpool washer that was 31 years old so when the motor went out I bought a Whilpool Cabrio. I HATE it!!! First, it takes at least an hour for 1 small load to finish. Then the clothes are not even clean and rinsed all the way. Dry patches on clothes and where the soap did reach the clothes there is white soap scum all over. I tried using the extra rinse function and still soap everywhere. Im hardly using any soap to begin with. I have to wash some things twice to get the soap off. Thought I was doing good by buying HE. What a waste of money. I cant wait til it breaks which should be soon according to all the previous comments. I have only had it 4 weeks. Dont buy this machine!

We hate the matching Cabrio washer dryer bought in 2011: Dryer lower blower went out after 18 months in service. The day it went out whirlpool sent me the extended warranty offer. Warranty had expired 6 months prior. I renewed for 12 months and promptly called for a repair. Cost was approximately $450.00, all covered under the newly paid for warranty. I dodged a bullet there. Washer has the splintering fiberglass around the top. Lower bearing is out and sounds like a freight train coming out of the laundry room. Not going to have it repaired. Looking for new units not manufactured by whirlpool. Shameful ROI. No more whirlpool products in our house.

Whirlpool washer Model WGD4815EW1. Bought this washer just about 4 months ago and right away I hated it but was told by people that all the machines had gone to the lid lock and that the government had mandated the energy saving devices on the machines so the machine will only put just a little water in the machine. I have been VERY VERY unhappy with this machine. My husband figured out a way to bypass the lid lock mechanism. Then after washing clothes many times I found out in order to get my clothes clean I had to just set the dial to Bulky every time OR I had to wash the clothes 2 times to get clean if I didnt. Once we bypassed the lid lock and then I figured out where to put the knob so the clothes would come clean I was fine until last week the machine just would NOT wash or do anything... it filled with water and just sat there until my husband got the water out. I located a Speed Queen from an appliance store and I am much happier. It does not have the CRAZY lid lock on it. I realize that some children are apt to mess with the washers. But I dont have children anymore and when I did I had a laundry room with a lock up high on the door so they could not play in the laundry room. I dont understand why this so called mandate could not have been done in a way as to allow those with kids to have the option on the machine with a built in code device to set the machine so the lid will lock and those of us without children in the house to opt out of the code to set the lid lock. NO REASON why we cant have a CHOICE. As far as I see it is a way for the government to try control more where they need to keep out. The cars have been designed with safety locks for children to keep them safe, but it is up to you to choose to use them. Same principle! Now for the mechanism to make it so the machine will only put so much water in the machine to wash. Youre NOT SAVING any ENERGY or WATER if you have to wash the loads twice!! This whole mandated business with the newer washer machines is a huge JOKE on everyone. I will be searching out used machines and having them rebuilt because I dont EVER plan on buying another one of these newer machines. If enough people stop buying them the manufacturing companies can raise some cane with the government to get the mandate lifted. NO I will not buy another Whirlpool washer. I encourage some of you out there who LOVE a challenge to figure a way to change the stupid motherboards on the newer machines and create a great business for yourself because if someone else can create it you can recreate it.

We have all kitchen appliances from Whirlpool, but it is not what we choose, that was builders choice. We, two people, are living in his apartment for almost five years, and first problem was with oven - the window in the door it is leaking somewhere, then microwave - the all front door plastic is cracking (we using microwave maybe twice a week) and is it placed under the oven. Now we have problems with fridge - the plastic inside the fringe is cracking. We called Whirlpool customer support and Whirlpool do not even want to hear it about the problems - they just want that same authorized technician will came to your apartment to inspect these problems for $95, it is not even important whose fault it is. This company, Whirlpool really DO NOT CARE about the products, which they produce - as long it is sells... Now we know, we made smart decision - do not accept the washer and dryer (we get it from Bosh - it makes me happy). Now we just wait till all Whirlpools appliances will stop working and never ever look back to Whirlpool.

Please DO NOT purchase an appliance with Whirlpool. I have had my double oven WiFi for 7 months. It has worked great. They did a update on it and I have had an hour glass for 2 1/2 weeks but the crazy part was they sent me a part, had it expedited 2 day shipping on a Friday and I didn’t get till Thursday of the next week. Go figure. So they send a new part and guess what? It’s broken and my oven doesn’t work once again. The other part is they have to wait for the code on the error 3-5 days. One we are going on week 3 with no oven and at this point I call and tell them my husband can run to Lowe’s and take a control panel off a new stove and put it on or better yet something is wrong with this oven. I need another oven because at this point I’m extremely pissed. Please DO NOT buy any products with this company. They SUCK!!!! They should replace it and pay me for all the meals I have had to buy.

Bought new dishwasher on 11/29/2013. Model #WDT710PAYM. The top rack cannot hold much weight. It keeps collapsing. One side keeps falling out of the track. Had man in for repair, still doing it. They sent me a new rack and rollers, still doing it. Having repair man come back again in a few days. I am so disappointed with Whirlpool. I cant believe they went so cheap in building these machines. I gave away a whirlpool gold that was 20 yrs old and it is still going strong with no problems. I just wanted to update up kitchen with stainless steel appliances. I will never buy whirlpool again!! This cannot be fixed. It just doesnt fit tight. Im stuck with a bad dishwasher and shouldnt be.

Whirlpool provides free replacement parts to repair this design problem but wont pay the service charges to repair their design problem. I purchased a KitchenAid french door style refrigerator (KBFS25EWMS10, SN K31902118) and it leaks water on the kitchen floor. At first I just mopped it up but later discovered they have a design problem in their drain system and water backs up into the freezer dept and eventually on to the floor. Customer Service provides free improved replacement parts for this design problem but wont pay the service charges to have the parts replaced. Simply put, Whirlpool/KitchenAid do not stand behind their product quality, instead they pass the problem and service charge cost for their design problem on to the consumer. Beware of this appliance supplier!

I have had Whirlpool appliances for a very long time. However, I am extremely dissatisfied with the purchase of my last Whirlpool washer a couple of years ago. The washer is extremely noisy, to begin with, and I complained to hhgregg about this. They delivered a couple of other machines, all of which were very noisy. The latest problem with this machine has been with the tearing my clothes. My clothing gets caught under the agitator and the items tear. This is a poorly designed washer and I wish I had never purchased it. I was thinking and wrongly so, that the washer would be as good as my previous washers. Well, I was so very wrong.I wish to know what you are going to do for me with this problem which is so very annoying and costly.Marjorie **

Whirlpool Dishwasher purchased at ABC Warehouse in Chesterfield, MI and was delivered on 10-2-2014, and one year later, we noticed that the tips of the lower basket were coming off. We contacted the holder of the extended warranty (5-yr.) and also Whirlpool. Both replied the fault was cosmetic and was not covered by warranty, that only mechanical/electrical components were covered. When we were buying the extended warranty, we were told that we were covered for all issues that may occur. We werent told cosmetic flaws were not covered. I guess consumers should, before buying a new product, make a specific list of possible problems, and make sure whats covered and not covered. We have been unable to resolve this issue.

I hate my Whirlpool refrigerator: It has a upper freezer with no light. The shelves are not split and raising or lowering shelves gains nothing and may even take space away. I would never ever buy another Whirlpool.

I bought the Whirlpool Cabrio 5.3 cubic foot washing machine to replace a Samsung equivalent machine. I am so extremely disappointed with it. As a mother of nine (seven of them boys) I need a quality machine. Unfortunately this is not one. The clothes come out of the machine just as dirty as they went in. The pants still have dirt on the knees. I think a rinse in the sink would yield better results. I use the highest soil setting, warmest water fabric will allow, and exclusively Tide detergent. I only fill the tub with half a load (completely voiding the value of large capacity) and yet still have to run clothes through twice.I really don’t have time for this. All the kids clothes have to be inspected before drying. I wish I could go back in time and keep my Samsung which was recalled. I would rather take the risk of an exploding machine than deal with this one any longer. Unfortunately, after spending over $1000 on the washer (and buying the matching dryer) I’m stuck with this useless machine. I hope others don’t make the same mistake I did.

The drawer guides on the large clear drawer at the top of the whirlpool refrigerator are very flimsy causing the drawer to drop when pulled out to the stop. When I called about this I was told it was cosmetic and not covered under warranty. I purchased the extended warranty which will replace the flimsy parts with the same flimsy parts. On 6/24/2024 Denisia sent me new side rails, exactly the type I have. I replaced them but the right side one broke. I regret ever owning one and will not recommend a whirlpool product to anyone. It is very obvious to anyone, after using this product, that that particular part is not safe and is definitely more than a cosmetic problem. I have already dumped the contents on the floor once and have just managed to catch it more times than I care to count. I spoke with Danielle on 5/14/2014. She sent the small plastic drawer that goes on the bottom.

Ive been thru 2 new French door refrigerators with the icemakers in the door. Ive lost all of my food more than 6 times! There is a design flaw and they are no longer making the large models. I finally figured this out after reading multiple reviews from a lot of people with same/similar experiences. The compressor freezes then the loud noise all while the temp slowly lowers and ruining your food before you know whats happening. To add insult to injury... After ordering my THIRD replacement, their contracted installation company wont communicate with me to let me know when it will be delivered. Ive been without a fridge for 3 months! Calling them takes a full morning with hold times over an hour! I will never buy another product from them. I have a taboo LG French door with an ice maker in the door in my other home and it has been perfect for 7 years. Just be very careful and read reviews from people who have owned one for at least a year.

I have a Whirlpool suite. Stove is fine...refrigerator is awful. Froze all the food in fridge. Cost me 100’s to replace. Put in new thermostat. Now sounds like a freight train. Bought in April and the filter already needs to be replaced to the tune of $81.

The Whirlpool HE H2Low Washer is the worst piece of crap Ive ever wasted my money on! It leaves soap residue on all my dark clothes! DONT WASTE YOUR MONEY! Whirlpool should be ashamed of themselves for continue to sell these pieces of crap!

I have called and emailed Whirlpool numerous times, complaining about the fungal odor emitted by my Whirlpool Duet front-loading washing machine (model #WFW9400SU01, serial#CSW0416732). I did everything they suggested that I do to no avail. A customer service representative said that the only thing left to do was to schedule a repair with a Whirlpool service person which I did. He called me when he was on his way and asked me what the problem was, and he told me I would be charged for nothing because hed seen this problem many times before and theres nothing he can do. Please advice.

Brand new Whirlpool dishwasher from PC Richards. Model #WDT710PAYB2. Dont buy one of these! In the store, I was turned off by the panel being on top of the door and not visible when the door is closed. I dont understand why anyone would not want to see the cycles and operation but my husband insisted that was a good thing so I agreed to purchase. Well, its horrible! I pressed the panel buttons the first time I tried to use it, and the panel switch is erratic and all over the place. For example, if I press Normal, the Heavy cycle button light goes on. When I hit start, all the button lights shut off. I finally get all the lights to stay on and hit start (after about 10 tries) and when I shut the door, the start button blinks and beeps! The dishwasher does not start. After many attempts, I got it to run, miraculously, for about 10 minutes. It emptied the detergent dispenser and left everything inside wet and slimy. Nice. I cant believe Whirlpool would sell such an inferior product. I have always been a loyal Whirlpool customer, but after this experience, I think its time to switch appliance brands. Now I have to be inconvenienced without a dishwasher after spending over $500 and wait for a repairman. Thanks, Whirlpool!

I bought one of the top of the line Maytag washers and was very disappointed. It only lasted about 5 years and had to be replaced. The dryer I bought at the same time is still working. It is 15 years old.

This is the information I tried to send to Whirlpool only to get a message that it was undeliverable: I purchased a set of whirlpool cabrio washer and dryer on 10-23-2013 (model numbers WTW8540BW, and WED8500BW). On 01-25-15 the washing machine failed to power up just over 2 months out of the standard warranty. This wasnt the low end cheap models. With cash discounts we paid over $1600.00 for the set. After a $70.00 dollar charge to the repairman we are told that the unit has a bad electric control board (part # W10761026). And unfortunately the part is on back order until March 1st, 2015 as of right now. So if and when the repairman gets the part and installs it, I get to pay him an additional $260.00. My family has always been such a dedicated Whirlpool appliance purchaser but this is wrong.Oh I almost forget, now I have to rent a washing machine at a cost of $55.00 per month until mine is repaired. I believed I was purchasing Whirlpool quality. The type of quality that doesnt need an extended warranty because Whirlpool is made to last correct? Please assist me in making this situation right and restore my faith in the quality I was raised with in Whirlpool products.

I purchased Whirlpool dishwasher, model DU930PWSTO, in 9/2007. It quit working in 5/2012. I expected an appliance made by a reputable manufacturer (Whirlpool) to last longer than five years. It seems like a manufacturing racket where they build these things only to be replaced a short time later. With service calls and parts replacement, its cheaper to buy a new unit. Talk about a circle jerk! And who the heck puts anything else but SS screws in a water soaked appliance? Duh. Rust! Im disgusted and dissatisfied with the whole company. Im still waiting on their response to my complaint email; at the time, the machine quit working. Whatever happened to pride in American made products? Or, did this get company bail and were now slaves to the Chinese junk once again? Ill never buy another Whirlpool appliance again. Does anyone have anything good to say about this company? I wish I would have read this blog before purchase.

Whirlpool gas range convection oven - I have only had this range for 2 weeks. Manual is sketchy to say the least. Purchased from LOWES - salesman were not well-informed. I have had to do a chat to find out information. Range looks great but performs poorly. Takes a while to heat anything even on high and on large burners. Grates are too heavy. I am sorry I did not see the editor review before I purchased. I have not used the convection so I cannot speak to this but my choices were limited when I purchased and I did not want a convection oven and other ranges would not purposeful for my use.

Whirlpool Washing Machine Model WTW4950XW2: I am 74-1/2 years old and I have been doing laundry for more than 50 years. We have always purchased washers of a brand made by Whirlpool. Until now Ive had nothing but the highest of praise. Two months ago, our washer stopped working and we had to shop for another. After looking at all types and brands of washers, we found out that the only type without an agitator was available. With that choice, we ended up buying the model stated above. I literally hate the way these washers pretend to wash clothes! I apply the detergent properly, place the clothes perfectly around the outer part of the tub, etc., and because there is not enough water that goes into the tub for the clothes to wash even one pair of socks, let alone a full load of clothes, I use the 2nd rinse trying to help matters although it doesnt. I dont care about the amount of the water I use to have clean clothes! The clothes sit in there just rubbing against one another, and then when they are finished, the clothes are so tangled you can hardly get them out of washer and into the dryer! Perhaps the designers of all these current washers think they are saving water, but I can tell you that sometimes I will wash mine twice as I know that I do not feel they are clean! (And I am a clean person and the clothes are not real dirty!) I am so unhappy with the decision of purchasing this horrible excuse for a washer that I could shoot myself. I will discourage every person I know from buying one. I will tell them to have their old washer repaired as many times as possible so they will have clean clothes! It isnt just Whirlpool, but all the manufacturers who have chosen to make this horrible decision for us, housewives, and anyone else who does the laundry where they live. I used to enjoy doing my laundry, but now it is a nightmare. I will tell my friends who are the same age as I am that if they can still find a machine with an agitator to buy 1 or two of them so they wont have to deal with this type of problem for the rest of their lives. I realize that now I have to eat this washer since I have purchased it, but I can tell you one thing; if I could sell it for near the price I paid for it, I would do it in a heartbeat! Realizing whoever reads this; it wont matter one bit and probably will never reach the hands of the ones who couldn’t care less or do something about it, but at least I have made an attempt to help others in the future.

Whirlpool Cabrio WTW8500DC0 - 2 months out of warranty, 14 months old. Motherboard fried. $300 if I do it myself. $550 to have it done. The unit was $780 on sale. Brand new piece of junk. Zero stars but thats not an option. Quite honestly, it doesnt clean very well and it doesnt rinse very well so we have to rinse twice to get the smell out if we use bleach. So whats the sense in buying a high efficiency washer? I work outdoors and weve had cheap washers in the past that clean much better and lasted many years.

At least three times a week the washing machine does not wring the water out of the clothes. The best Maytag wants to offer is to extend the warranty for one year. So washers are supposed to last for 2 years? Will never purchase a Maytag again!!!

I purchased a Whirlpool Cabrio washer in 2007 and had to replace the control panel for $300 each time twice.

This has been the worst purchase I have ever made! Within 2 months of it going out of its one year warranty I called (Lowes) to have it repaired. Spent $300 on the first repair to get rid of the jet engine sound AND the oil splatter all over the floor then within one month from that repair it has a F code error and wont finish washing a load. It just stops. I have tried everything from unplugging it to restarting and it just wont work. Now have to wait 1 week for the repairman to come back out (hopefully that warranty of 90 days will be helpful). Do Not Buy this machine!!!

Purchased a 40 gallon gas water heater from Lowes. Installation was a nightmare trying to get the 3/4 pipe nipple fittings to seal. Once getting the two nipples to seal using extra thick Teflon pipe wrap, found the tank was leaking also. The return with Lowes was painless. Got another Whirlpool to replace, but angry about having to do the job twice. Wish I viewed this site first. Never would have purchased Whirlpool.

I used their website to schedule an appointment for an estimate for a repair on my oven. I was never told they were sending an independent contractor to do the repair nor that there would be a charge for the estimate. I contacted Whirlpool and was told there is nothing on their website and I should have asked the service technician before he was at my door if there would be a charge. Therefore, it was my fault and I indeed had to pay the charge when I declined to have my oven repaired. I paid an independent contractor hired by Whirlpool for $129 to give me an estimate on the repair to my oven despite never being told of such a charge prior to the appointment.

Contacted this am. See through top glass lid is separating from plastic causing sensor to turn washing machine off. Looked complaints up on this machine and it is a common occurrence and is a defect. The machine is a little over 2 or 3 years old and out of warranty. Was told not a common occurrence and I would be responsible for repair. Model # wtw7800xw2. Serial # c12270139. Thank you.

We had the same thing happen. We purchased a brand new home and within 6mo the plastic around the handle started breaking off and pieces would fall into any food that was being cooked on the stove. Whirlpool fixed it for free but now the same thing is happening with the new door.

Ive had so many problems with this washer. Everything has been replaced on the machine and it is still a failure! It has overflowed 5+ times. Stopped draining 4 times (fun getting water out of it...). Have been without a washer for a total of two months! My In-Laws have the same and theirs hasnt been a problem (however it isnt used as much as mine.). Hopefully mine is just a Lemon! Ill never buy another one!!!!! Especially from Lowes. They deem it only a lemon if it has had the same issue for 4-5 times. That is with the extended warranty! TO THE DUMP IT GOES!

After almost 10 years, my Whirlpool top loader is now malfunctioning just like a lot of complaints here. It will not complete a wash because it keeps giving an off balance error at the spin cycle. I also had a coin get stuck in the discharge hose but fortunately it did not destroy the pump. I certainly dont want to sink any money into a repair especially because the techs dont seem to know how to fix the off balance problem. Im not much satisfied with my Whirlpool dryer either. It takes forever to dry a load.

I have spent 30 minutes trying to change light bulb under the oven and get the cover plate back on. I watched the film on how to do it, it was amusing to watch the struggle to get it on. It was amusing to say the least. Whirlpool watching it??? I do not believe whoever designed this worthless time consuming light cover never tested it one time, or it would had been more user friendly. It amazes me what kind of trash they can build for us consumers to have to deal with at times. Tomorrow this overhead piece of junk is coming out and being replaced by a non Whirlpool one. I am going to get a tractor and smash it into little pieces and put on side of street with a note saying this is what happens when you try for an hour to change the bulb.

I bought a Whirlpool High Efficiency top load washer. It does not get the clothes clean. Dark clothes come out with spots all over them. There is not enough water to rinse out the dirt. It is left on the clothes in spots. I have to take my clothes to the laundry mat to wash them to get them clean. I am 74 years old and have used Whirlpool appliances all my life. I have dt3 rental houses I keep Whirlpool appliances in. But I wont be buying any more. I had to call the repair man one month after I bought it. He had to recalibrate the machine. If all you want to wash or maybe rinse out is a pair of slacks or a shirt, it might be o.k. but not a load of dirty clothes. It is just a JOKE.

On Dec 18, 2015, my hot water heater located in my garage started spewing water out into my garage, driveway, and into the street. I called Lowes, whom I purchased the water heater in Jan 2011, in which it was still under warranty. I was told to call (Whirlpool) 877 817 6750, the order was placed for a gas shut out valve after going through a check system. I was then given the names of two local preferred technicians to repair water heater, whom was not available. The representative from Whirlpool (American water heater) told me I can get the plumber of my choice, authorization number was given. I had to call the (Whirlpool) (American Water Heater) back and was told the part was ordered 2 times. The first part will come on Dec 19, 2015 by UPS, and that the second part will come on Dec 21 by UPS, that a prepackaged label for return will be attached, and to tape the 2 boxes together to send back to the company--one box with the old part, and one box with the new. So, I sent the boxes to an address in Junction City, Tn. But I was not sent prepaid label, so I kept by word and spent $14. I will not be reimbursed according to American Water in which I followed their directions to a tee. So the walk away, the customer is always wrong, staff is not being trained the right way, and as a customer I am out of money and making adjustments to the way of customer service. No service. Just a waste of time, effort, and money.

This washing machine is a piece of junk. It broke down exactly 2 days after the one year warranty expired. Home Depot said there was nothing they could do and Whirlpool said the same thing. This washing machine was not used on a weekly basis. It perhaps washed 20 loads during the course of the year. I had many issues with the sensors before it broke down completely. Sometimes, half the clothes would be dry after the entire cycle. I was so angry that I had a local independent contractor come in and look at it. He said the motor was broken and needed to be replaced. So much for $700 down the drain. I will never buy a Whirlpool product again. This was the worst experience Ive ever had with an appliance.

Ive always had a Whirlpool washing machine and it has been extremely dependable. I have not had any problems with my Whirlpool washer. A Whirlpool has came a long ways with their pricing. It was very affordable for somebody like me and I cant afford a lot but I could afford this. I was very pleased with my purchase and with the product. They havent let me down so far.

I purchased 4 whirlpool appliances at Leons in Mississauga. The side by side refrigerator was replaced within a few weeks. Got a new one and have had that one fixed at least 3 times already. The stove was serviced 3 times now, the washer broke so many times. They gave me a refund. The microwave broke as well. They told me it was not fixable, then I called Leons and they said it was too old. It was only 18 months old. Did not get anywhere with the microwave. Had to buy a new one. The only appliance I had that didnt break was the dryer. So far. The fridge now has broken inside, the crisper wont slide in and out at all. Cant be used. I bought a warranty on all the appliances, and even though I had a warranty, when a coin got stuck in the washing machine because the drum inside kept banging because it was in need of new struts, they still charged me 135.00 to fix it. Two to three weeks later a repairman came and put new shocks on it. Finally after having it repaired about 5-6 times in a year and half they gave me a refund at Leons and I went to pick out a new washing machine. Overall I have spent about 6-8 hours on the phone complaining and making appointments with Whirlpool Canada.

We bought a top loaded Whirlpool washer, model WTW5000DW2 last May from Lowe’s for a summer beach cottage. It has been a terrible experience. There was a 30 day warranty from Lowe’s which unfortunately we missed because we had not moved down for the summer till after the 30 days. Working through Whirlpool, they sent an independent contractor out 5 times over the summer. Control panel was replaced twice. It never worked properly. I’m now back for the summer, and it still does not work. Do not buy this washer.

Bought a Whirlpool range in Nov. Within a month the large burners fell apart and the reflector bowls discolored from normal use. Call Whirlpool and they sent out replacements. Within a month the first replacement fell apart and the new bowls discolored from heat again. I held off calling until the second burner fell apart and this time when I called I was told I would have to stay home to wait for a service call to have burners replaced which I could do myself and that the bowls arent covered and that it normal for them to discolor with normal use. They said I should wrap them in foil to protect them.They appear to prefer wasting time and money rather making a good product. The burner bowls from my old GE stove are still shiny after many years of use but Whirlpools cant hold the finish for a month. Please note I was an appliance tech and ran an appliance repair business for 18 years. These failures are not normal or acceptable. I will never buy Whirlpool again.

Bought a Whirlpool Cabrio. Noticed it was getting really loud less than a year into owning it. Called while it was under warranty. The tech said it was fine. Within the next year and a half it got so loud, you cant hear anything else in the house while it is running. Now it is leaking from the tub seals and the bearings are going out according to two service techs I have had come look at it. They say it is more expensive to fix than the washer is even worth. This is due to the parts that would be used to fix it are the same cheap Whirlpool parts that were put in it in the first place. They both said that these are not good washers and commonly go out about a year and half to three years old. Shame on Whirlpool for making such a low quality product and not being willing to do anything about it.

Had this model (WMH73521CS-6) installed as part of kitchen remodel. After 8 months, microwave is failing, indicating door needs to be opened, then closed to operate. This does not fix the issue or reset the condition. AND, there is no way to reset the microwave electronics, not even power cycling (unplugging and replugging from/to electrical outlet).

Ill be just as responsible as Whirlpool and Nasons has been... I bought my Whirlpool stove less than 2 yrs ago from a reputable business in a nearby community, CROWN POINT, INDIANA! I have had trouble w/ the burner knobs ever since I bought it...just brushing up against them turns them on. Enough gas escapes into the kitchen... I bought knob covers to prevent that (they did NOT work)! So I called the place I bought the stove from and they sent out a repairman...he said there was no fix for it... but that I owed him $69.99 for the service call. And every time I turn the oven on to heat it to bake something you smell gas also... Im almost afraid to use it... 3 nights ago I woke up to the kitchen filled w/ gas...knob covers on but still one was still on a bit... it was a whopping -25 and we had to open windows to clear out the gas... you shouldnt have to check the knobs once youve turned them off. Nor should they come on when you brush by them...when youre not even cooking... Granted I am short but the serviceman said I should move everything I needed to cook w/ closer to me so I didnt have to brush up against the stove... what????? I have cabinets above and all around the stove. What I cant use those cabinets????? Something is terribly wrong w/ the stove and the service... If youre in the market for a new stove, dont buy a Whirlpool and for certain DONT buy anything from NASONS appliances in Crown Point Indiana... They along with whirlpool dont stand behind their product... They told me they never had that complaint before. WRONG, I read it more than once on this site...liars all of them!

I have to say I am taking the time to write a review for my Whirlpool Cabrio Washing Machine since Ive never been this dissatisfied with a product. Every time I wash my brand new expensive black dress pants, I have resulting white marks all over! Im so upset! I washed one load three times with no soap at all just to remove the marks present! At this point, I will never buy another Whirlpool product. =(

On November 1, 2011, I purchased the Whirlpool Estate washer (model # ETW4400XQ) from Wholesale Appliance in Charleston, SC. The first time I used it I knew something wasnt right when both the regular and so-called gentle cycle agitated at an incredibly fast speed. It is damaging my clothes. I called the dealer and they sent out a service person. He said that was just the way it was and he couldnt do anything. So, I keep trying to use the gentle cycle, but it was the same thing. I would have to stand by the machine and stop it after a couple of minutes so it wouldnt ruin the clothes. The more I thought about it, I decided that the repairman wasnt right. I called Whirlpool customer service and they sent a different repair service. He also said that he couldnt do anything to make it slow down as it was programmed by a computer inside and he could not change it. I went to the dealer, Wholesale Appliances, and they said there was nothing they could do as far as giving me a refund or a discount on a better machine. The setting on the washer clearly says gentle cycle.” Well, the whole world knows that does not mean beat the clothes to death as fast as possible. Can you make any suggestions? Thanks.

Purchased Refrigerator (WhirlPool Refrigerator WRX988SIBM03) 16 months ago and noticed the drawer with glass that house the drawers had a crack on the right side. Couldnt believe it was cracked after such little use with just two adults living in the home. Removed it and noticed this was such shoddy design. There is a heavy metal bar in the back with a piece of flimsy plastic that attaches to the heavy metal bar with only a screw attaching the plastic to the metal.I made attempt to glue it since it was only cracked but then the plastic just started crumbling into pieces like a broken cookie. Truly there is something wrong with the quality of the product as well as the design of having this heavy metal bar attached to this flimsy plastic. The quality of this part only leads me to believe what is next with this refrigerator. I am sure there is more to come.I contacted Whirlpool to see if they would replace but of course this is at my cost. Ive had inner parts of refrigerators break over years of use and they get old and busted up over time but this is a new refrigerator and once I inspected the part, I was disappointed with myself for not removing these inner parts and inspecting prior to purchasing. I would have picked up on the poor quality right away. Taken by the outside of this unit and its beauty, and not truly looking at whether or not the shelf can hold a couple gallons of milk. I am here to tell you there is no way this would have withstood the test of time with only a gallon of milk sitting on this unit. Poor design, poor quality and metal attached to raw plastic as it is a disaster.

I purchased my Whirlpool gas range about 5 yrs ago as brand new. Two and a half years after purchase, I started getting the F2 error and always had to pull the breaker to stop the oven. Whirlpool would not do a thing, they wouldnt even listen to me. So I bought a new control panel. Now once again here it is the holidays and Ive started getting the F2 error when I try to use the oven. So needless to say this is my last Whirlpool appliance. And the Service Officer wont even listen to me when I say I have to buy a new oven.

I have the stainless steel Whirlpool Gold appliances. They look beautiful but do not work for long. For one, the dual burner never heated properly on the cooktop. I just worked around it. The oven vent on the cooktop left brown marks on the stainless facade attic top by the clock. Ive read some have melted this area. Then after 2 years, the entire front glass door and handle fell off when I opened it. It not only fell, but the cheap plastic lip that holds the door on cracked so it is impossible to get back on. So, since I cant afford a new stove. Im stuck with this horrible looking mess in my kitchen.

I purchased a Whirlpool gas top range from Lowes in Somerset Ky September 2013. Model number WFG524SLAB1. The surface is showing bubbles. I contacted Whirlpool and they gave some kind of story. In other words I am stuck with it. Still under warranty but they wont send someone out to look at it. Lowes told us that it could be a paint defect when it was made. If the top starts peeling, it will be a real mess. I have never used anything abrasive on the stove top. As of right now I am not happy with Whirlpool at all and if they dont do something about this, I will never buy another one of their appliances.

I contacted Whirlpool on 3 separate occasions. Each time they told me to have the plumber call them so that they could determine what the problem was. Each time he was able to get the water heater going again, but it would only operate for about 3 months and then it would go out again. To date, I have incurred $245.00 in plumbers service fees. My last call to Whirlpool was on 5/14/2013. This water heater was purchased on 1/25/2010 at Lowes in Evans, GA. It went out over the weekend, but the plumber was able to relight it. When I called Whirlpool on the 14th of May, I was told since it was working now, there was nothing they could do. I am tired of dealing with this issue. They wont stand behind their product.

When I purchased my Whirlpool Cabrio washer and dry, I was told by the sales associate that this was the top of the line. I paid a higher price for what I thought was quality only to find out that this washing machine (WTW6600SW2) Serial number CU2973872 is in fact poor quality, made of components that are cheap, unreliable and made to last only as long as the initial warranty. Prior to buying Whirlpool, I owned Kenmore and had a washer and dry that raised four kids, now I own a Top of the line Cabrio that cant wash the clothes of two adults. I think it is funny that two days after the washer started sounding like a jet plane taking off during the spin cycle, I received your sign up for an extended warranty letter. Then I take the washer apart to locate the trouble and find it is a single bearing on the top of the drive shaft, but can I buy the bearing and replace it? No, I have to buy the entire outer tub and drive shaft. So a $10.00 bearing will now cost me $200.00. I am sure that helps your profit margins considering all you have to do is a search for Cabrio problems to find 350,000 hits, or to ask a professional technician and receive the reply that they are replacing 2-3 of these tub and drive shafts per week. I would recommend that Whirlpool tell its shareholders that you have compromised customer satisfaction to line their pockets with profits. If that was your intent then you have succeeded, however you need to also tell them to sell their shares now as you will have no return customers. Most corporations have core values that deal with safety first and then always followed by quality. I can say with confidence that your quality can be nowhere near the top five with this many problems with your top of the line product.

In the past 8 years, I have had to replace 2 Whirlpool Calypso washing machines and 1 Cabrio washing machine. All 3 washing machines worked great for the first 2 years. I purchased the Whirlpool extended warranty on all 3 washers. The first Calypso had 12 repairs done on it. Finally A&E repair service deemed the washer not repairable. Whirlpool replaced the Calypso with a new Calypso. Based on the problems with the first one, I again, purchased the extended warranty. Again, after the manufacturers warranty expired, I again had issues. After numerous repairs, A&E deemed the washer unrepairable. I contacted Whirpool warranty service and was told that they would reimburse me 75% of the cost of their choice of a Whirlpool washer! Since I have had 10 hand surgeries, I need a washer that does not have an agitator (hence the original Calypso purchase). The model that Whirpool warranty deemed as a replacement had an agitator and was also a much lower energy efficiency rating. I found that the Cabrio was a comparable replacement model and finally Whirlpool agreed to replace the washer at 75%. I was angry that they didnt cover the total replacement, but felt at least I got a totally new problem-free washer. I again purchased the extended warranty. I got the Cabrio in March of 2008. In April of 2011, the washer started getting rust around the bleach dispenser and also I would get UL code (Uneven Load). A&E tech came out and replaced a bearing. He said that the rust was not covered under the warranty. I asked how it was okay to have rust around the bleach dispenser if the washing machine is always wet with water. A month later, I was still having a UL code and the rust was getting worse. A&E came out again and said that even though I saw rust around the bleach dispenser, the rust was in fact underneath the tub and had eaten away at the parts. He called the warranty company to authorize repairs and the Whirlpool warranty company denied any more repairs on the washing machine.

DO NOT buy Whirlpool branded electric ovens. Whirlpool put out an update and it fried the control board of our electric built in oven. They refuse to fix it. They have kept us on hold for two hours and then tell us there is nothing they can do to fix it. We had an extended warranty that just “disappeared from their system.” They told us someone would call back us but no one has. This was an update we were told we had to run in order to use the associated APP. Our oven is only 2-years old. We now will need to pay for the repair ourselves. DO NOT BUY.

Whirpool Product VMW TL WASHER with impeller absolutely is crap. I have it almost a year and it smells, and it noisy like a dog was in the machine and someone started it. Its off balance constantly. I hate it and will place on every blog the worst review I can write. Its a nightmare. It has a fake bleach dispenser a door but no holder underneath. Even the repairman thought the bleach went in the dispenser. My clothes were ruined along with sheets, etc on numerous washes. The bleach partially dispensed on dark clothes at least 8 washes.The washer was purchased at BrandsMart 11 months ago and so theres no returns.

My induction cooktop totally failed to work two months after installation. Whirlpool sent a repairman who told us it was the main board. He also said he was unable to locate any of that part anywhere in his computer. We called Whirlpool via our store, Ikea. They apologized, asked for 48 hours to locate a part, then said they would replace the cooktop if they were unable to find out. Almost 48 hours later, they hadnt located it and denied any replacement option. The parts cost is over $800. The cooktop cost just over $900. Whirlpool reps would only read from a script of legal warranty jargon. Then they said they needed 5 to 7 days. We had a baby visiting - we needed our stove. To me, an apology would be replacing that unit if the part wasnt available, not a verbal statement. Fortunately, we had the phone # of a local Ikea manager who told us to bring the cooktop to the store as they had them in stock. They replaced it with a new one. Over the years of my long life, I have bought many Whirlpool products. Never again. I need a washer and dryer, and will not be purchasing any associated with the Whirlpool Corporation. Thanks to Ikea, though, for standing by their customers.

I purchased a Whirlpool Cabrio washer and dryer. They work well but the washer underneath lid has rusted already. I did purchase the washer in Dec. 2011 and in June 2012 the inside lid to my surprise had rust on it. I called the Whirlpool company and was told that is considered cosmetic and not covered under warranty..

Since my review I have been corresponding with Whirlpool Customer Service (Chris). First he sent me an email and mailed a replacement board to have us (the homeowner) install. Because the cover was so melted, the replacement board would not fit down into it. I emailed pictures to Chris. Once he saw the pictures, he called me and arranged for the water heater to be replaced since it was still under warranty. He even extended the authorization code so we would have plenty of time to arrange for a plumber to do the work. We had to pay for the plumber, but Whirlpool arranged for us to have a new water heater. Now I can sleep at night without worrying that my house would burn down if the old water heater caught fire. Chris was GREAT to work with. I had a direct number to him and called any time I had a question. I was very impressed with Whirlpools Customer Service.

Its very noisy, and there are no blankets to purchase to deaden the noise. The dishes all need to be dried by hand. Some of the dishes come out dirty. I would never purchase another Whirlpool dishwasher.

Our dishes always come out completely clean and without spotting. I dont like having to get down into the machine and clean out the filter/trap, so I pre-rinse everything that goes into the machine, so that might help. Regardless, this machine does an excellent job. This is the Whirlpool Gold Series bought in 2013. It has numerous settings, such as delay, varying cycles, air dry, heat dry, etc. All the features work as expected, but like most owners probably do, I leave it set on the same settings all the time. It does what I want and does it very quietly. This is a standard, under-counter, full-sized machine. The outside of the dishwasher is stainless and the inside has a plastic lining. The controls are at the top of the front door, so that leaves the front completely clean-looking. Love it.

Ive always had good luck with Whirlpool. They last longer & dont have as many repairs. Ive had to have a lot of repairs with Maytag washers. The dryers didnt give any trouble. I recommend Whirlpool.

I thank the folks at Whirlpool for building a washer (Cabrio tub bearing failure) that lasted 22 days just shy of four years, better than the Whirlpool Duet that lasted 14 months, tub bearing failure also. Now I have high confidence that Whirlpool pre-engineers failure into every washer they build.

I am very sorry I bought this machine. CU rated it pretty good. Nope. 1 - It rarely dries everything completely. e.g., the collars of t-shirts or turtleneck shirts are damp after the load is finished. I have to run the machine again....Energy efficient? Energy schmefficient. and I havent even TRIED to use the low heat delicate cycle. 2 - The cute modern buttons are hard to push in. 3 - The top of the machine doesnt have a level lid... Its curved. Not very useful for setting anything on while you work at any part of your laundering process.

I chose based on the current ratings of the machines. They look nice and they can handle large loads. I think EPA has changed wash machines to be back into the 1920s. I put my clothes in and there is no agitator in the center. My clothes come out twisted tightly into little round circles or balls, not much water but now it takes over an hour to wash my clothes. So we are conserving water but using more power, I also have to iron sheets and clothes because they are so twisted and wrinkled. I used to stick my clothes into the washer, select a cycle and go on my way and now I have to answer 5 other selection options, if I dont hold the button in long enough it just turns off.Have we all lost our minds, I think this is going backwards not forwards. I have talked to other women and they agree with me, we HATE these new washer and dryers. The dryer is a little better but not much. Also the tops are concave so your laundry basket falls off, and you cant put your soap on the dryer which is where I am used to having it. Now I have to clean my washer every 30 cycles, iron and it takes all day to do the laundry, yes and they call this progress, really!!! I purchased the Whirlpool Cabrio W10607 425A- SP and dryers Whirlpool W10680129C-SP, these are full size and have the steam options on them and are side by sides.

My Whirlpool Cabrio Washer is a bucket of junk. I bought the washer in about 2008. I was smart and bought the warranty for approximately 3 years. Since I bought it, I have had them replace 3 water pumps, the tub, the computer, and it still knocks and shakes. It also leaves small frayed holes in my beach towels. This machine should be recalled. It needed a warranty from day one. Washer cost $1,000 warranty every year $130.00 per year which covered the repairs at about $900.00 for repairs. I hate it. I just hate it. I can’t stand it anymore. I need a new washer, someone has got to listen.

The knobs on the Whirlpool gas stove model Super Capacity 465 AccuBake system are easily confusing and dangerous. If the knob is turned in the wrong direction when intending to turn the burner off, it turns to a very low setting which is although nice for simmering, it is very easy for it to be mistaken as the off position and leaves only the gas leaking if the smell is not noticed in time.

We purchased the washer on April 25, 2015. It has been an absolute nightmare. Reached out to Sears within a week of delivery because the wash cycle was way over an hour. Is a terrible machine, my clothes come out dirty, is damaging my clothes and Sears says I cannot return it because according to them I havent had it fixed enough times. It washes for over an hour at times. It takes water and releases water and goes to wash again but is not cleaning the clothes. As a homeowner we pay water, and electricity and perhaps I wouldnt be so upset if my clothes would come out clean. At first the tech told me to change from the HE detergent purchased and recommended at Sears to liquid detergent and then since I still get stains on our clothes he advised me to use less than the recommended amount. I also purchased the kit to wash the machine. This is a real lemon and nobody wants to admit it. I have purchased Whirpool washer before but if they dont admit that this is poorly made and give me a voucher to buy another machine I will never ever in my life buy Whirlpool or Sears for that matter. The machine is just a year old and I cannot use it because it damages my clothes and worst, is not cleaning my clothes. It disgust me to wear dirty clothes or to have my family wear them. So now I have another appointment and at this point I no longer use the machine. I will tell everyone that is willing to hear my experience. Do not purchase this washer, is not good and is only trouble. You are not going to be able to get it exchanged or fixed. I think that a full year would have been enough time for Sears to determine this is a lemon and do the right thing by the customer. I now go to the laundromat because I have a machine that damages my clothes. I am also out of money to purchase a new one and the wearing dirty clothes disgust me.

I purchased my Whirlpool Duet Steam Washer and Dryer 4 years ago. My laundry never had that moldy smell. I paid for the set almost $2,900.00! Never again Whirlpool for sure!!!

We purchased a Whirlpool stove a year and half ago. We were cooking and kept hearing (tick, tick, tick) noises. Couldnt figure out what it was. After removing the pot there was an area of 2x4 inches that had melted in. Not sure where the glass went. But it looked like a chip but on the surface.

Its just a plain refrigerator. No bells and whistles. It could have more space in the bottom and well as a ice machine or ice maker. Nothing special about it. Just a place to keep food. The light in top could be higher so food does not touch it.

Whirlpool Gold Bottom Mounted Freezer - I advised Whirlpool that the refrigerator has two design flaws... one that makes the drain freeze up and even more importantly what is involved in correcting the problem. They replied that they were unaware of the issue when its all over the internet and has been for well over a year... maybe more. I sent them a couple pages of internet links and they said they would advise their engineers. As they have done with others, they suggested I should have gotten the extended warranty but that hardly addresses the problem(s).

The company I work for bought a new washing machine a couple of months ago to make it easier for those that do the laundry here. The washer was suppose to be this great washing machine which has turned out to be the biggest piece of trash on the property!! Every couple of loads you have to turn it off and hopefully the computer in this Whirlpool cabriolet will reset so you can wash a load of clothes. You have a 50/50 chance it will work. DO NOT PURCHASE THIS MACHINE. IT IS THE WORST WASHING MACHINE IVE EVER USED!!

For the second time in 18 months, I have had to replace the top shelves on my refrigerator (Model #ED5VHEXVB01) because the cheap plastic borders have broken. The first time it was covered by the 1 year warranty, but this time (12/11) Ill have to pay $130 just for one shelf. Unless the quality of the product has improved, Ill probably expect to have to replace them again within the year. Needless to say, Ill never buy Whirlpool products again. Im out $130 because Whirlpool will not replace them for free because the product is no longer under warranty.

I am not pleased with my self-cleaning oven. I dont even use my oven that often and I cannot get off even the simplest of stains on the sides, top, and bottom. I have tried to clean the oven three times and the stains from pie drippings are still not coming clean. It should not be this hard to clean an oven because my last oven was so much better and it was not Aqualift. The top of the oven is also very hard to keep the burners clean and looking like new. I am very disappointed in this oven and believe that this is false advertisement to the consumers. I pride myself in keeping my kitchen looking clean but this just is not working for me!

This machine needs to go back to the engineering dept. There are too many engineering defects to mention. My Cabrio washer and dryer was delivered October 11th of 2017. It is just my husband and myself so laundry was scarce. I have been unhappy with the washer since the beginning and just recently decided to try and solve the problem. I contacted Whirlpool first and was told these machines have great reviews and nothing is wrong with them. When I started describing the flaws, there was one excuse after another and the person from Whirlpool blew me off. The flaws... all begin with not cleaning which is caused by design. The water level, even with the deep water setting, does not even cover the amount of clothes in a small load; the agitator is so small, there is no effect on agitating the clothes; even with using a SMALL amount of HD detergent, there is always soap residue on the clothes because of the lack of water; and last issue but not final is the load going off balance. The machine will walk all over and error codes according to the repairman need to be cleared so must call if it happened again. Well, the very next load it went off balance again. I did not call because I would have the repairman living with us and I am not willing to set up a bedroom for him or feed him. So, Whirlpool does not care if their product needs redesigning, they only care about selling their product and then the consumer is on their own. Basically the same train of thought from Best Buy where we purchased the machines. Best Buy would be happy to sell me another laundry set... per the store manager but that is all he could do. Will I purchase from Best Buy again... I think you know the answer to that. If they cannot stand behind a product they sell, then they can keep everything they sell, no more money coming from my checkbook to them ever again. Someone, whether the manufacturer or the retailer, should be willing to stand behind their product. But, no one cares. Bottomline, do not believe the ratings on the Cabrio washer. This machine has design flaws that cannot be corrected.

I just bought this water heater on 2/12/12 and it has already started having problems. I got a self diagnosis of the gas valve needing to be replaced. I think that if this becomes an ongoing problem, whether I have a warranty or not, I’m going to trash it and go with another brand. I shouldn’t have to pay to have the gas valve replaced.

This is not a new washer (Whirlpool Cabrio INTW6200VWO) and it works well BUT since we have owned it we have had rust at the bleach dispenser. I am seeing on the internet there are many complaints about this and there was a recall? But they have run out of replacement parts??? Never received any recall notice. We have online instructions on how to repair and have done this many times and the rust comes back. About a week ago we sanded, primed and enamel painted the area plus I have put NO BLEACH in the dispenser and the rust is coming back. I hate to replace a working machine but this rust can and will get on my clothing. Whirlpool was the absolutely best in the past but this one is a lemon.

It took several delivery attempts to get a refrigerator without cosmetic flaw and it only lasted four years before Freon leak in evaporative system occurred. It would have cost more to repair than replace. Needless to say, I replaced it with another brand.

Just had the repairman at my house to repair my 2-year-old Whirlpool refrigerator Model GB2F4DXWS07 - he couldnt fix it. Just throw it away and get a new one. There is a blockage somewhere in the line, he suspects the lines were not cleaned before it was charged at the factory. Repairman said it was a typical 20-year-old refrigerator problem. Customer service was no help - Whirlpool live chat is currently unavailable. Lousy product with worse service. I will never buy another Whirlpool product.