In June of 2010, I purchased a new Whirlpool Estate EED4400WQ0 dryer (serial number M01156261) with an accompanying washing machine. It has been in a clean, climate-controlled environment and gently used by my family of four for just short of two years. Last week, I began to notice that the clothes coming out of the dryer were cool and damp and it quickly became apparent that the dryer was only heating intermittently. This morning, the service person from the dealer who sold me the washer and dryer set (and a Whirlpool dishwasher a few months later) told me that contacts on the timer unit were bad and that the entire switch would have to be replaced. This is no small portion of the machine and the part alone will cost me about $150. After labor, we are looking at an expense of approximately half of the original cost of the machine - in less than two years. I called the Whirlpool’s customer service line to ask if there was anything that could be done and the answer was: Sorry, we cant do anything for you.” It is not acceptable to me for an appliance to become that expensive that fast. If Whirlpool cant do anything for me about this, then I will not be purchasing anymore Whirlpool products.

Its a piece of junk. The only time it will finish a wash and spin dry is when it is empty. Otherwise, it stops and lists an unbalanced error code. I opened up the service panels and found no broken hangers or clothes. There’s no way to bypass the system. I have read of similar issues and of course, its just out of warranty. I assumed the warranty was like other brands but it’s much shorter. What to do? Purchase a washer with dials and not a brain; it will last years. Note that the models without a brain cost far less.

Whirlpool slide in range, microwave, dishwasher, KitchenAid fridge: All appliances, stainless finish, were bought with my home in October 2006. Range - Within the first year, I had problems with the outer plastic pieces breaking, the motherboard and the oven and broiler not working. The screws holding the knobs on fell out several times. The oven door was fixed several times this past year until finally it fell off and broke for good and now the oven does not work at all. Microwave - The rotisserie motor stopped working this past year. Dishwasher - Just after the first year, the outer shell of the door came apart. KitchenAid fridge - Within the first year, the temperature adjuster broke. The second year, the ice maker stopped working. This year, the ice maker broke again and the motor quit working twice already and all has been repaired. The freezer handle has fallen off as well.

I installed my new water heater in 2012. Within 3 months, it was not producing hot water. When I called, a helpful person at the Whirlpool warranty line told me it was because there was too much cold water being mixed into the hot water coming from the tank. I hung up... Called again and was told that they would be able to get someone in 2 weeks out to my house to check it. I told them that was not acceptable. I hung up... I called Lowes, where I bought it. The person on the other line finally, after more than 1 hour, was able to get a repair person out there within 2 days. I had to pay the fee to have the guy come look at my hot water tank, and tell me that he hated Whirlpools. He called Whirlpool, 3 times; he was hung up on 2 times. He explained what had happened was I had a hot water leak, that it probably it was overloaded, the thermostat control everything else was fine. However, that I had installed the heater myself not a professional. Therefore it was not up to NATIONAL code; therefore, Whirlpool refused to honor the warranty. So, short version, in order to get the tank repaired, I was supposed to spend an additional $300-$400 to bring the heater up to code for them to honor the warranty. What you ask made my heater out of code? It is outside in my utility room, and the flue was cut to fit and the OUTSIDE vent pipe was not above the roofline. It didnt matter that it is not in an enclosed space, that this was nothing to do with the reasoning the thermocouple went out.I simply turned up the heat, so far so good. Will I ever buy another Whirlpool? No. I have a Whirlpool fridge bought before the hot water tank situation. The ice maker went out within 6 months of purchase. When I called to have it repaired, the service guy stated he hates Whirlpool. The piece he had to replace was plastic that was replaced with a metal piece that should have been metal to begin with.

I purchase newly Whirlpool washing machine but it was not working from the first day of my purchase. So many service Engineer came but nobody can solve the problem, so I suggest to all please don’t buy washing machine from Whirlpool. I am very disappointed from this company.

Whirlpool gas range Model WFG5245LAB2 has serious flaws that are a danger. I noticed the handles to turn on the burners seem sloppy. So sloppy in fact that just brushing up against the knobs will turn the gas on. This happened when I had someone visiting and we returned you could smell gas in the house. We were none the worse since we were out however my 3 cats were in the house the entire time. Tonight I removed the large grates that go over the burners to clean the porcelain. Once again I brushed up against the handle and the back burner ignited causing me to burn my hand. This stove is a danger to all.

My not yet 3yr old ($2100.00) Whirlpool refrigerator started having problems. I thought it was related to the ice maker. When the repairman came out, he said it had leaked the Freon, so I thought it should have been a simple fix. Boy was I wrong. It turns out it has a sealed system so no one can access this to fix it. It is now junk and I have to buy a new one. I will never purchase Whirlpool anything ever again and I will also tell anyone who will listen about my experience. My repairman said this happens all the time, and 7 or 8 yrs ago Whirlpool went from being one of the top models to being junk.

I have a Whirlpool Cabrio WTW5640XW and I was able to get the belt back onto the pulley, about a month back and it ran, loudly, but it ran. Last week the belt popped off again and now the pulleys are screwed, so I probably won’t buy another motor (for the sake of the pulley). Ill get a front loaded Kenmore or something as I was never completely happy with how this thing washed and (didnt dry) our clothes.

I purchased a new Whirlpool Cabrio set, in 2009. I bought the top loading washer, and matching dryer. Since 2009, I have had the washer serviced FIVE times. Bearings, water pump, F1, F2, ul codes, and a few other things, I honestly cant remember. I love this capacity. But that is all I love about this machine. Today, the water pump went out again. I have been reading online regarding loose coins making their way into the drain pump, the hose, and other parts of the washer. I am diligent about emptying my pockets, but, obviously, someone in the house is not. There should be a trap for the coins, buttons, and any other debris that passes through, but, clearly there is not, and it appears I am not the only one with this problem. I am so frustrated. I paid almost $3,000.00 for this set. It was my very first brand new set and I have had so many problems with this. With all of the problems and all of the complaints, and so many similar complaints, why is Whirlpool not acknowledging them? Why are they not doing anything about it? Side note, my dryer works fine.

This is not a new washer (Whirlpool Cabrio INTW6200VWO) and it works well BUT since we have owned it we have had rust at the bleach dispenser. I am seeing on the internet there are many complaints about this and there was a recall? But they have run out of replacement parts??? Never received any recall notice. We have online instructions on how to repair and have done this many times and the rust comes back. About a week ago we sanded, primed and enamel painted the area plus I have put NO BLEACH in the dispenser and the rust is coming back. I hate to replace a working machine but this rust can and will get on my clothing. Whirlpool was the absolutely best in the past but this one is a lemon.

We purchased the unit in March, by April it wasnt cooling. In June it shut down. In July after 8 tech appointments and repairs. Whirlpool finally said they would refund my purchase and I should see the money in about three weeks. That would be about a week longer than the refrigerator worked. I dont have the money to just get another one so I guess the family will be without a refrigerator for another month. That means shopping every day for perishable for a family of 10. I would not recommend another Whirlpool product. This is no joke, every time I called them one of the first things asked was Did you get the extended warranty? Why would they ask, sounds as if they dont trust their own product either. This unit was purchase online through Sears.com. Purchase price was $2299.99. Order placed on March 4, 2017.

We purchased the Whirlpool Cabrio washer a few months ago. When we wash the white cloths using the (white) setting and add bleach and the HE detergent, the washer does not clean the white cloths very good at all. Sometimes the white cloths come out looking worse than they did before they were put in the washer. We called the people at Whirlpool and they said there is nothing they can do as long as all the functions on the washer work the way they’re suppose to. I thought the function of the washer is to clean the clothes but, they say no, as long as everything on the washer is working. That is what their warranty covers.

The refrigerator is not repairable according to 2 different servicemen. The refrigerator just stopped making ice and not cooling all of a sudden. The problem seems to be inside the panel between the refrigerator and freezer portion. Its a side by side. First time I ever bought Whirlpool Appliances. To make things worse my Whirlpool oven does not work either. Even worse, the Microwave pretty much popped and never worked again. A Whirlpool microwave. The only thing still working is the Whirlpool dishwasher but I wonder for how long. Ive talked to Whirlpool and they said I only had a 1 yr warranty and they could not help. I am writing to their corporate office to complain. I have an old Maytag refrigerator that still works and puts out ice in my garage. I went to look at Maytag appliances and just found out that in 2006 Whirlpool took over Maytag. So I will not ever, ever buy another Whirlpool or Maytag again.

Extremely disappointed in Whirlpool oven! Built new home and this was recommendation by BAC Appliance. The oven does not self-clean well at all, and my spills are minimal. Deposits between glass doors that cant be removed. Oven is barely cleaner than before I cleaned for full cycle. Oven suddenly shuts off for a short while and then restarts. Steam comes when using lower oven and removes finish on upper oven. I expected Whirlpool to have a quality product. Definitely not! BAC really had no answers for me.

Purchased my Whirlpool Duet front load washer WFW9150WW00 new in 2010. Also purchased extended warranty. After four years, just before my extended warranty was up, the entire inside needed replacing (drums, bearings). Now at only five years old, it keeps making a beeping noise in middle of wash cycle and wont continue working. Serviceman was told by a Whirlpool tech. that it could be two things, one being the door jamb, the other being the control panel. Door jamb was fine. Ordered new control panel ($240), had it installed and yet the washing machine still keeps beeping and doing the same thing. The serviceman doesnt know what else it could be. So, I am forced to return the part and purchase a new washing machine. I would never recommend Whirlpool to anyone!

Cabrio Top Load Washer model WTW6800WW1 - Although we were very happy with the vendor where this was purchased and happy with the majority of the washer function; there is a problem with the cabinet & lid connectors rusting. Specifically, the lid connector on the left side totally rusted out, and also around the bleach cup, rust. There are also rust spots where the seam of the top section of the washer meets the bottom part. The washer was purchased in 2009. We have had it serviced in the past, prob 5 years ago, it needed a new motor and the rust was beginning to show then, while under warranty. I recently called Whirlpool and the associate told me that she had never received a call with regard to this type of problem. She did give me names and phone numbers of appliance repair in my area. I find it odd that Whirlpool would not make their associates aware of issues like this. I searched online and saw more than a few complaints about rust. So on it goes, no recourse, and as I read about the problem from others reporting this; it was mentioned that the vapors from the bleach cup etc, contribute to the rust. Additionally, even if it was under warranty, I was told that this is considered cosmetic and it would not be covered. Until... and I can only suppose, that until the lid possibly falls off while lifting, the cosmetic ruling may then turn into a function problem. Now there is also a squeaking sound, so off to call the appliance repair, check the cost and next time... buyer beware. I guess a lesson in science as well, hopefully this design flaw will be corrected for the next models in process.

Purchased Whirlpool refrigerator at Lowe’s. Refrigerator would never get cold enough, so I exchanged with a Whirlpool Gold side-by-side refrigerator. After installation coffee was spilled behind refrigerator. I was unable to pull refrigerator out from wall to clean coffee spill from behind. When checking with Lowe’s on the 35th day, I was informed that Lowe’s 30 days warranty had expired and I would have to work directly with Whirlpool.I discovered it was very hard to communicate with Whirlpool; there was a problem that they only had on file the first refrigerator I purchased not the one I kept. The Whirlpool service rep did not seem very cooperative but with insistence they told me they would change my information to the correct model and serial number and a repair order was sent to a local service shop. The problem with not being able to roll the refrigerator out from the wall is that Whirlpool had changed their wheels to a tri-wheel support and there was not enough height on the single front wheel to lift the refrigerator to clear the screw down leveling stops on each corner. The service rep had no solution for the problem and had to call the Whirlpool service. He indicated he never was able to get assistance from that department. I told him I would talk to them as the consumer but they refused to discuss the matter with me, so I gave the phone back to the service tech. Whirlpool told the service tech to order replacement wheels of which I knew this would not resolve the problem.After two weeks, the replacement wheels arrived, the service tech installed them and as I expected they did not resolve the problem. I then requested the service tech to remove the rubber from the stops on the corner to allow for the additional required clearance and this solution worked. This is a very poor design for Whirlpool, but I accepted the results. Two weeks later I receive a phone call from the service business and they tell me that Whirlpool did not have the refrigerator model/serial number they worked on. Whirlpool was not willing to resolve the problem I had with them initially and the service business would have to bill me directly and was not covered under the warranty.At this point I lost it and informed the service business I resolved this model/serial number with Whirlpool before. Whirlpool gave them the authorization to work on the refrigerator and they would need to collect the fees from Whirlpool. I have purchased my last Whirlpool appliance mostly because Whirlpool makes it very difficult or refuses to talk to the consumer and it appears the quality is no longer there. Will Whirlpool become the next Kodak? With this kind of service, people will just quit buying from them.

The gas water heater that we purchased has been a headache. Pilot went out several times. When we contacted Customer service they informed us that we would have to have a new kit put on it. We ordered that and it worked a while and then we started having the same problem. Just recently we had to purchase another part and once again we have cold water. Fed up.

Cabrio washer broken lid, asked WP to fix warranty. They offered $250 off $500 Amana washer. Said just send me the new lid that would cost me $210. They said no. Asked if they would send me metal lid with hinges less than $100 they said no. Told them I was not going to spend more money with WP, my turn to say no. If you are wise dont buy WP products...

Our Whirlpool Duet front loader washer developed a mildew smell and started making a horrible banging noise on the spin cycle. We had a service man come out and the concrete weight had broken in half. He said this was not uncommon. I just did a Google search and apparently this is a true factory defect. Luckily we had purchased an extended warranty. I always thought Whirlpool was a premium brand but after this experience I will never buy another washer from them. They should do a product recall.

We purchased a Whirlpool washing machine for $600 from a local retailer and it broke down within three months. It is now been two months and two repairman visits later and still not fixed. I called them and talked to customer service who then transferred me to another department. So far it’s just been the typical runaround with no results. I demanded an immediate replacement but was told that would need approval from yet another department. I don’t remember what departments are involved nor do I care. I am simply disgusted with this baloney.

Bought washer just under three years ago and the tub bearing started to sound like a jet airplane. Whirlpool seems to have an ongoing issue with the tub seal which goes bad and then allows water to enter the bearing which then fails. Whirlpool will not make it right, I guess I will have to plan on a $350 repair every two to three years if I keep this machine. I am very disappointed with whirlpool for not standing behind what is a known problem. They should replace these seals under warranty so that the Bearing does not fail. Thats my opinion, recall the seals and fix a bad design problem. I would not recommend ANY whirlpool products to anyone at this point. What other problems do they have with their other products?

The washer has rust under the rim in the inside - also the paint is bubbling and peeling under the rim of the washer. I contacted Whirlpool and was told that is a cosmetic problem. There is no warranty for rust or peeling paint. I will never buy another Whirlpool washer. I paid over $700.00 for this washer and I dont think I should have a rust problem after 5 years.

Purchased the washer 11/26/12. Did not get extended warranty.... big mistake. By 12/1/13, control panel went out. Serviceman assessed ($100 service call). Quoted $495 to replace. ABSOLUTE JUNK! So very sad and angry that there is no recourse with Whirlpool.

Very disappointed with this product as well as Whirlpools handling of the situation. I purchased this item 9/15. Its now 10/16 and the plastic that surrounds the glass on the shelves has cracked on 3 of the 4 shelves. The company will not replace because the warranty time has run out. The cost to replace and ship is around $500.00. Big disappointment.

I purchased a Whirlpool fridge (model GX2SHBXVQOO) on November 27, 2010 and it leaks water on my floor. I have to keep a towel there or it runs all over. I also purchased a Whirlpool range (model YGFE461LVQ) and the convection fan went on it a month after we bought it. The manufactures warranty does not allow repair people to travel any further than 100 km to repair, something that we had to take the stove in to be repaired. We got the stove back the same day and brought it home. Low and behold, after a short period of time it started to rattle again and got steadily worse. Also, now my one burner on high does not stay on high; it keeps going out then coming back on.I have called the place we purchased these pieces of junk from and they said there is nothing they can do. I also sent e-mails to Whirlpool and they said they will look into it and get back to me. That was months ago. I called Whirlpool and was basically told that there was nothing they can do, that I was to call the repairman. Never, never, ever buy a Whirlpool product.

Totally worst experience with Whirlpool fridge with 1 year of the purchase. It started having cooling issues. Also it was making noise. When contacted for its replacement the company did not agreed for the same saying would provide free service within warranty period however after that customer will have to pay. Quality of product (shelf life) is too bad in context with the company it belongs to.

It seems the quality issue of the LED of the washer Whirlpool Cabrio. It was broken from the screw part of the glass and the plastic/alloy and the glass. They would charge me $416 to replace the LED but I rejected and was still required to pay $85 for labor fee. I called the company and they didnt admit that was a quality issue but I just found many consumers had the same problem. If someone would like to have a lawsuit, please contact me and I will join.

I owned a Kenmore washer for approx. 20 yrs that endured 6 kids for most of that time period. When time came for a new one, I had to have the latest model, and settled on a Maytag Bravos approx 3 yrs ago. This was a huge mistake - I paid between 600-800 for this machine, and it is a piece of garbage. The repairmen here yesterday explained to me that Maytag and Whirlpool are now the same company, and also that all these machines are now made overseas because of cheap labor. In a nutshell, I was given an estimate of at least 300 to repair this piece of crap - he explained that they are only made to last a few yrs -where is the justice in this situation? I really dont get how these big companies get away with selling crap, knowing all the while that the consumer is getting screwed - yet people continue to buy them..

Doesnt wash clothes properly - often some items of clothing just dont get wet. After 3 years the whole main bearing in it failed, causing unbelievable noise and constant overload faults. All Whirlpool top load washers have this critical design fault where water leaks into the main bearing (the bearing is an unsealed type with a cheap grommet seal) and then after a year or 2 the bearing starts to cease and the machine overloads itself trying to operate. Replacing the bearing means pulling the whole machine apart - and with a cheap press-fit bearing like this, special tools are needed and it will never operate smoothly again anyhow. In any case in 2 years, the faulty bearing seal design will let water destroy the bearing again. Effectively it is not repairable. Sounds like class action to me. So, it became an $1000 paperweight and I bought a new Samsung unit. I assume the Koreans know how to design bearings and seals...

Refrigerator, less than one year old, quit working and destroyed several hundreds of dollars worth of food. Whirlpool warranty division was notified and a service technician was scheduled to arrive yesterday, a week after the warranty division was notified. Yesterday, no one arrived. Today the warranty division was again notified and we were advised the service technician was never scheduled and they do not know why this happened. Here we sit again for another four days awaiting a service technician.I am disgusted with the failures of Whirlpool and their warranty division. Again, in less than a year Ive paid nearly three thousand dollars for a refrigerator and it fails, destroying hundreds of dollars of food. This has been a complete struggle trying to maintain food in a household both children. I expected a long time manufacturer to provide better warranty, service, and not just tell me they are not sure why. I would hope that no one ever buys their products again, God knows I will not!

I purchased Whirlpool 6.2ct electric range on 3/16/2013 from Lowes, Fremont, CA. I tried to bake my cake on 11/19/2013, and preheat it to 400F degree. When the temperature achieved to 400 degree, I put my cake in not even 5 minutes and go to dining room to pick up something. When I turn around, I saw the oven window is so bright and I open the door right away, it has fire from the left side bottom. I turn off the power right away but still has big fire. So I use the fire extinguisher to get the fire off.I went to Lowes to complain, this product is still under the manufacture warranty and I also purchased two years extended warranty from the store. Lowes sent the 3rd party technician over to check, they open the bottom element and insist I drop something to catch on fire. He tried 350F degree is working. But the fact is, theres nothing dropped, no oil, water or and any ingredients, only fire extinguisher powder all over the bottom. Technician put back the cover, I asked him, How do I clean up the bottom extinguisher mess? He said, You dont need to, just clean the top, and wont try 400F degree for me since the top didnt clean up. I asked him, I am so fear to use it now, you asked me to clean it up and try again. I only use my oven to bake cakes, cookies, and muffins, and that day the cake even not still raise yet. How could it catch on fire? Is this product defective? I doubt it.I also called Whirlpool, they said most likely its short circuit. They only provide the repair, unless it cant be repaired, then they replace it. Manufacturer also told me that my temperature is high. I dont think so. I have no problem to use any oven in 425-450 in the past. If this is high, why your stove has function to that high degree? I am so upset with both services. From my concern, nothing dropped to bottom and caught on fire. They all refused to replace the new one and asked me to continue using it. I really dont feel confident to use this one and dont know who can help me to replace it.

We bought a new Whirlpool counter depth side by side stainless steel refrigerator in January 2012. We have had 7 service calls because things were freezing on the top shelf. They installed a new part and it still froze. They told us to do dumb stuff at Whirlpool like turn the temp up, dont use the top shelf, etc. The money they want for these appliances and you should put a band aid on it to make it function properly? Duh? The final fix was to duct tape the vents to allow less air flow. This appliance should have been recalled. I have since read reviews and it is an ongoing problem. Before buying, do your homework and make sure the other brands are not manufactured by Whirlpool. The Whirlpool hotline for problems is not that service friendly, they have an attitude. I need to replace two more appliances and they will not be Whirlpool. The repair service was great but they are independent companies, not Whirlpool. How do you fix a lemon? Consumers need to be aware of this. Whirlpool would rather spend money on repairs that did not work instead of replacing the appliance. If you want 7 or more repair visits and no results, buy Whirlpool.

I had a Whirlpool dishwasher for year and it worked great, but the baskets were rusting. I decided Feb 2014 to purchase another Whirlpool dishwasher. It did not clear as well as my old dishwasher. The seller of the dishwasher stated it was our water or detergent. The water and detergent were the same. The only difference was the dishwasher. Day prior to changing the dishwasher, the dishes were clear and the day I changed the dishwasher, the dishes were not clean. November 2016, the main board has gone out. The part costs $148, plus the service call. I called Whirlpool. They stated they would sell me the part or would discount a new dishwasher. I think they should discount the part!!! Whirlpool makes most brands of dishwashers, so you cant change companies. Their quality is all you can get.

New stainless steel range 5.3 cu.ft. with convection oven delivered by Home Depot on time. Before the day was over the trim around oven glass was falling off. Double sided sticky tape was not holding. Yes its put on using double sided sticky tape. Called Home Depot, once you accept it, you deal with Whirlpool. They must first send someone to look and see. Yes its falling apart. Service tech will order new door. Mind you it will also have the sticky tape. We have also noticed that the glass top has many deep scratches, he will replace that also. A week later still no word, when. Used the oven because I couldnt wait and as it heated up smoke poured out of it and a loud noise from inside. Turned off and pulled out bottom drawer to unplug. Bottom panel had fallen down and undersides were rusted. Only had the stove 3 weeks and its Christmas Eve. Will read reviews first next time. No problems with my other Whirlpool appliances.

It works ok and fits in a tight spot. However, the top shelf will suddenly start to freeze the food and after a day or two it will stop. The fridge makes terrible loud banging noises. Were told it is the coolant but it is extremely annoying. A repairman moved the line closer to a heating and it doesnt bang as much. Because of this, I would not buy a Whirlpool fridge again.

This washer was expensive, platinum line. Clothes never smelled fresh and clean like they should. There is not enough water to cover and clean. After 4 years it started smelling dank and unpleasant even after cleaning cycle is run. Now I discover it has been leaking for quite a while. It will be 6 years old in July. The top wont stay up. This happened months ago. The part alone is 250.00 according to several sites. I just prop it up. Very displeased with this poorly constructed, expensive rip off!

The fridge had been leaking just a little for a while until the leak picked up and left a puddle. Turns out this plastic tube connector cracked. Seems a very poorly designed fit that caused the bend in the plastic to rupture. Now the whole tube and what I think is the water inlet valve will need to be replaced.

When washing towels or a blanket or quilt, anything substantial it wont spin the water out of the laundry. This washer is only 5 months old.

I had ancient appliances (refrigerator, microwave, range, and dishwasher) that were all mismatched and were in the house when I purchased it in the mid 1990s. I saved up my money and even though my old appliances were working fine, I wanted stainless steel and everything to match so I decided to go ahead and replace my refrigerator, microwave, range, and dishwasher. I decided on Whirlpool since the company has been making appliances for many years and I thought they made a good product. I bought those appliances in 2012.In 2015, the microwave started to malfunction. At first, it would light up and act as though it was working, but it wasnt. I had it repaired - they said it was a fuse - and the fuse repair cost me about $75.00. It worked for about 2-weeks. I called the repair guy back and they didnt charge me, thinking it was something they did wrong when they fixed it. This time it worked for about a week when it went out again. Not wanting to miss any more work waiting on a repair guy, I went to Lowes and bought a pack of the appropriate microwave fuses and replaced the fuse myself. This time it worked about three weeks - I noticed it was popcorn that seemed to kill the microwave. I finally gave up repairing it when I used up all the fuses in the pack from Lowes. I bought a GE Microwave and it has been a dream. It does a better job all around and looks a lot better than the Whirlpool. I no longer have matching appliances but at least they work!But thats not all. Now the Whirlpool refrigerator has been slowly dying. It has been groaning and creaking since I had it installed but it has gotten so loud that I have to sleep with white noise so that it doesnt wake me up. Yesterday, I took out a Drumstick ice cream cone from the freezer - they are the cones that have chocolate covered ice cream with nuts. I bit into the chocolate coating and the ice cream all spilled out like milk! Looks like Whirlpool struck again and I am not even going to bother to repair it. I just hope I dont get food poisoning until I can get it replaced. And...the dishwasher. Well, it wont dispense the Jet Dry liquid if I fill up the reservoir. I have to fill it only half way or it wont work. I had to use an eyedropper to get the tank down to half. It doesnt really get the dishes clean either. My 20+ year old one I got rid of was 100% better than this Whirlpool dishwasher.Luckily, I hardly ever use the range...and when I do, its a burner or two so I havent had any problem with it yet. I am thinking of replacing it anyway simply because I dont want - ever - anything that says Whirlpool in my home. I was so excited when I decided to buy new appliances. I was finally going to have something new and nice in my home...or so I thought. Instead I wasted my money and got aggravation instead of joy. I dont know about others but I will never buy Whirlpool appliances again- never ever. And now I feel like my money was stolen from me -- and my joy definitely was stolen.

Microwave model WMH73521CS-2: Microwave is approx 2.5 yrs old. This is the 2nd time we have had problems with door open and close msg appearing on display. We had to have door latches replaced once and again are having to have it serviced again. $100 for service to come out again, does not include cost of replacement parts. This seems to be a consistent problem with this model. We are not replacing the parts and are buying a different microwave. Definitely not Whirlpool. I called Whirlpool and was on hold for almost an hour and received no resolution to problem.

I just bought a house that has one of these ranges, and it was getting the F2 message. I found the problem. There is NO ventilation behind the electronic control so when the oven heats up, the control board gets too hot and throws the F2 code. That would indicate a bad temp sensor or bad board, but really its the heat shield on the back. Ive removed the metal plate from behind the control panel and it works fine now. Im considering drilling some vent holes and adding some insulation behind the control.

Bought a commercial coin operated Whirlpool washer on 4-18-2015. As of this date machine has not been used that much, the electronic part has gone haywire.All lights on and shows the door lock (which is not) disconnected, nothing changes when I put it back. Contacted Whirlpool technician, have been told that this is a defective model. He has apparently had several service calls that are new machines and they are all the same issue. Told to contacted Whirlpool, Whirlpool playing dumb. I have several other older Whirlpool commercial washers and dryers, never had issues. I guess they are doing shortcut garbage machines. Also, the interior of machine is less sturdy than the older models. Will not buy any Whirlpool products again. They do not stand by their products try to tell me that they are not aware of defective machines. Cheaper to play stupid!!! Disappointed with their lack of standing by what they sell!!!

The French door fridge with the freezer drawers on the bottom are very flexible and easy to access. It goes downhill from there. The ice maker takes 4 days to fill up the bin with no use. The unit does not defrost and freezes up every six weeks requiring a manual defrost. Three mods have been made under the service contract and performance has not improved. PC boards have been replaced and at least one thermistor. My understanding is this is a single compressor unit with piping, relays and valves to port refrigerant to two different evaporators as needed. Unfortunately it simply does not properly balance/defrost and the freezer door freezes up. It certainly is not compatible with a high humidity environment. We will never buy another cooling design like this, but sure like the French Door layout. Glad we have a service contract.

Whirlpool Electric Convection Range - We purchased a Whirlpool fridge, range and microwave, I am finally sending my review after another of many frustrations with the AquaLift self cleaning oven. NEVER, NEVER buy one unless you love cleaning your oven. The temperature goes to 160 for 40 minutes, it does nothing to clean your oven. I called the co. we bought it from. The fellow said, Oh you should clean your oven weekly, really there are 2 of us and I use the oven maybe 2-3 times a week without spillovers. When I do have spillovers I use the AquaLift waste of time, then have to spray it down with Affresh Spray the co. I bought the range from recommended, still have to scrub hard to remove built on spills. Save yourself the money and frustration. Buy anything but a range with AquaLift self cleaning.

Sixteen months after I bought the Cabrio washer (model # WTW7800XWO), the F1 error light came on. I had to replace the electronic panel on the machine for $400. Whirlpool refused to replace it even though they have been replacing this panel for others. This is a common problem with the Cabrio washer.

The knobs on the Whirlpool gas stove model Super Capacity 465 AccuBake system are easily confusing and dangerous. If the knob is turned in the wrong direction when intending to turn the burner off, it turns to a very low setting which is although nice for simmering, it is very easy for it to be mistaken as the off position and leaves only the gas leaking if the smell is not noticed in time.

We too have nothing but problems with our supposedly top of the line convection/microwave oven. Purchased in 2010 in February for new kitchen. From start, original microwave installed did not work, would not cook or heat. Dealer replaced. One year later, same problem, but now out of warranty. Had to pay labor, costs, and parts to get fixed. Fast forward 13 months, again magnetron needs replaced, microwave will not work. What a hunk of junk for our money. I will never buy any Whirlpool appliances again, and I will tell everyone I know the same. When you call customer service, they are nice but only say “too bad, out of warranty”. What a joke for a major appliance company to tell customers. It is obvious that this microwave is faulty from the get go, and they just keep on making them the same way and not trying to fix the problem.

I bought a Whirlpool water heater in 2009. I paid $588.46 at Lowes. Turns out it is in a class action lawsuit for faulty thermocouple. I was given a coupon from Whirlpool for 2 new thermocouples as part of the class action lawsuit. The thermocouple goes out on it every 1-3 months. You never know when youre going to have a cold shower getting ready for work in the morning. I literally could have bought a new water heater for what Ive spent on thermocouples the last few years. The last two times it went out, I had to replace it twice within 1 day. Im sick of replacing it and have decided to install a new hot water heater. I am disgusted with Whirlpool and tried to contact them about it but have gotten no response. I will never buy another Whirlpool product and would not recommend them to anyone!

Long story short, we replaced a very old Whirlpool water heater with a new one a couple of years ago... We have had nothing but trouble. First, pilot light wouldnt stay lit. Found out that it was defective.... Whirlpool DID offer a no cost conversion kit. Had to pay shipping and installation costs. Have had the plumber out four more times to try to ANYTHING to keep it lit.... No luck. He even spoke to a Whirlpool tech on the phone and followed his advice. I have filed an online complaint with Whirlpool and the site stated that I would hear back within three working days. Guess what.... no reply. I have four other Whirlpool appliances that I love, BUT as they wear out, I will NOT consider Whirlpool.

I bought the front load washer 4 years ago. The tub bearing suddenly broke. We have 2 people in the house so the washer is not used more than 4 times a week. I was told it would cost $700.00 to repair. The washer was bought with a stackable dryer. Now Im told they no longer make a washer to go with the dryer. I called Whirlpool/Maytag and they could care less. The explanation I was given is that it is a man-made appliance. That is the worst customer service I have ever gotten. I would never recommend Maytag/Whirlpool. In fact I will highly discourage against it.

I have always liked Whirlpool products but it seems lately they are lagging in this department. My washer/dryer combo each separate I dont feel are doing the job they should be. Washer is the bigger problem. Softner dispenser not distributing the softner correctly and now I have to clean out after each use. These are about 10 years old now. Is not spinning all the water out and not at all sure if clothes are getting clean. Most of their products usually lasted much longer back a few years.

WARNING: Do not get the warranty plan through Whirlpool if you have stackable washer and dryer, you will have to remove the dryer yourself before they come out to service your appliances. I was willing to pay extra to have them take it down, the contractor said I had to call the extended plan service, yet 6 telephone numbers later to include the complaints department to no avail... Whirlpool contracts out so get your own and you may save a few dollars!

I really like my new 5 burner gas double oven gas range made by Whirlpool. Except for 1 minor flaw where the backsplash panel warped at the beginning and was promptly replaced by whirlpool I have had no problems with my range, love having 5 burners and a double oven. Plus the left front burner has a much bigger burner with higher btu which helps water come to a boil way faster than any other ranger I have ever had. That is a real nice feature and I really like having 2 ovens, When cooking on an average day for my small family there is no need to heat up the big oven and the little oven is just the perfect size to bake 1 or 2 dishes. And on holidays when I am cooking for more people or many more dishes I have the capacity to cook more items.

We bought a new Whirlpool just 3 years ago. The first year under warranty, we made several calls for repairs on the water and ice dispenser. The water was never cold and never fixed. Just after the warranty expired, the water stopped dispensing completely and now the ice will not dispense. We bought this refrigerator to have cold water and ice at ease, but it never happened.

I have had this Cabrio washer and dryer for two years now and I would do better washing my things by hand. Save water, sure there is none!! I have a glass lid and I actually stood there and watched a cycle and the clothes on top never even got wet!! My whites are now gray!! Called the company to get nowhere. I am going to buy an old-fashioned washer that actually uses water. I tried to be eco-friendly but I dont like dirty clothes!!

I have a two year old Whirlpool dishwasher. The soap dispenser cover broke shortly after the warranty ran out. It cost 100.00 for repairs. A year later, it broke again. I sent a letter and the part to the CEO of Whirlpool. They sent a repairmen to fix it free of charge. When you have a problem with a Whirlpool product go to the head of the company. If they get enough calls they will make better parts. Call 1-269-759-6919. Write a letter, return request receipt. It takes a little effort, but it helps a lot of people.

I paid big bucks for a five burner, convection stove. I had a pot of boiling water on and the steam melted the plastic cover over the controls. Whirlpool said I had to buy the whole electronic panel. Close to $175.00!

I have had this range for approximately 4-5 years with no problems. The design and efficiency are great!! I would recommend this brand to anyone and would purchase it again myself. It has an extra burner just for warming which I love.

Washer doesnt get soap out of clothes. Had tutorial from service man. Must use extra rinse every time and still have soap on dark clothes. Worst washer I have ever owned. Makes washing a lot of extra work and frustration. Have tried everything to no avail. Takes at least three times longer to wash clothes with all the steps I have to take to get soap out. I understand EPA demands for less water usage, but clothes still must be properly cleaned.

Since there is only two people in this home, we decided to go for the smaller front-loading machine. This was purchased in 2012, still running. It does a clean wash, however common sense does remind people to not over-load a front load washer. If one follows directions, it gets the job done, and ones machine lasts longer without problems. Thanks.

I have a lower end 4 burner model but I love it. Both power burns are in the front (I would change that) and electronic ignition. The oven temp is true and heats up quickly, I bake upwards of 700 cookies at Christmas time. Even being a lower end model it works great and I use it everyday. I think it is more energy efficient than the model that I replaced, which I replaced in order to have the electronic ignition. I would recommend this Whirlpool Range!

I purchased the Cabrio washer and dryer 4 years ago and had no problems until recently. The motor and the harness broke and the cost to repair was almost as much as a new washer. The repairman told me that this is a common problem with all washers that Whirlpool makes as they have the same motor and harness. He gave me a list of all the brands that they make and suggested if I buy one to get an extended warranty. I would not recommend anyone buy an appliance from a company that continues to manufacture faulty products. I wonder if they own the extended warranty company?

Whirlpool washing machine has always been reliable for me. I have owned 2 and they lasted me many many years. Its easy to use, and cleans clothes perfectly. My family is also a fan of Whirlpool appliances.

After doing much research on refrigerators, I chose the Whirlpool with the French doors and bottom freezer. Within a month, I had to call the repair service. The freezer made a thick layer of ice on the bottom, wouldnt shut properly (I had to keep a heavy box in front of it to keep it closed) and frosted over all the food in it. On his second visit, the repair man told me that the company knows about the problem, that there was a problem in the design of the appliance, and created a piece to be installed in the machine to alleviate the problem. The problem has not been fixed with that added piece, and the repairman has been here a few more times. Now the freezer just randomly stops making ice on top of all the other problems it has. The retailer would not take the fridge back, and I refused to buy an extended warranty for an appliance that the company themselves knows is a lemon.

I have bought and used other dishwashers (different brands). They lacked quality, quiet operation and efficiently and effectively cleaning dishes, pots and silverware! My Whirlpool dishwasher is far better than all of them. It cleans and makes my dishes sparkle. I would not buy anything but Whirlpool in the future.

I purchased a $950 whirlpool refrigerator from Lowes in Tucson. 2 months after the 1 yr warranty expired, I paid $450 in repair bills to have it fixed. After 9 months of visits by the repairman and loss of hundreds of dollars in spoiled food, they deemed my fridge unrepairable. Then Whirlpool called me and said they would exchange my fridge for a better one for $688. My loss is now up to approx. $2000 counting spoiled food.

For many years, I have worked on and tested water heater thermocouples. I have a lot of experience with this. I have checked around many of the wholesale supply houses to find a simple part needed for this brand/manufacturer appliance. Johnstone Supply, a national wholesale distributor, Grainger, etc. cannot get these parts. You must call Whirlpool and wait on the phone and give the operator the full story about what you found and how you tested the water heater only to be told you dont know what you are talking about. I was told that if the pilot lights and stays lit for even several minutes, that it is not the thermocouple but the gas valve and they will not sell me the part and recommend either I purchase a whole gas valve assembly and revised thermocouple or they would not sell me anything.Then I got told that I am on a waiting list to be called for availability of the parts at some time within the next 24 hours. Or just buy a new water heater from us with a warranty. Really? This is why you should not even have wasted your time with these people and move on to a better future. I asked,Can I purchase a box of thermocouples for this type of water heater with a left hand thread? The answer to this was, No, we will need the serial # for each unit that has had any part put on it. Move on, I say. This was a big waste of time by me, the plumber, and my customers happiness.

I purchased a Whirlpool washing machine (new) in 2004. From the beginning, I had problems with the spin cycle. I phoned Whirlpool. I paid for service with no reimbursement. With the costs I have had for service, I could have purchased 2 machines. I have had to go to Laundromat to do wash then come home to dry. I have for 30 years only purchased Whirlpool large appliance. My washer and dryer were always refurbished but they were Whirlpool. I have had a (refurbished) Whirlpool dryer since 1997 with one (1) service call. However, this wash machine, purchased new, has been a money pit and a piece of trash with Whirlpool only giving lip service when calling. Also, going to the Laundromat, I have been amazed at how many individuals I speak with are there doing wash because their Whirlpool washer, mostly even newer models than mine, do not work! And they have the same story. There’s no service when you call. Shameful Whirlpool! Buy your parts from us. Maybe your credibility could be restored. But I will never purchase your Whirlpool or other names under Whirlpool! When I do get another washer, yours will be put on my front lawn with a large sign of your disgraceful products and service!

ED5PHEXNK00 Stainless Steel side by side Refrigerator bought in 2004, look out!The refrigerator caught fire today and there was smoke everywhere. Had I not been home, damage would have been out of control. I traced the smoke to the bottom of the refrigerator. I pulled the unit out from the wall and unplugged the power to the unit. My unit is out of warranty and past the extended Lowes warranty. The repair diagnosis is $100 to start.Whirlpool has recalled its other brands (Maytag, etc.) for this same problem but not its Whirlpool brand. Our problem is the same problem with hundreds of other people: Whirlpool fridges burning, smoking, and being a life threatening hazard to families all over America because of the faulty relay to compressor. Whirlpool better recall this model. They need to fix this or they will have much bigger issues to deal with (corporate manslaughter from a known issue and no action or protection for its consumers). The refrigerator is a result of Whirlpool’s negligence; thus, it’s potentially deadly.

After 14 years of good service with Whirlpool Duet front load washer dryer set, wife chose Whirlpool kitchen appliances as part of a kitchen update project. All matching fridge, range, microwave hood and dishwasher. What a nightmare! The icemaker growls and whines all the time and the dishwasher was broken before being packaged at the manufacturer. A wheel from the middle rack was missing when the dishwasher was opened. It wasnt in the sealed dishwasher nor in the box. So it had to have been broken off before the item was boxed. We called for warranty claim and A-1 Appliance was recommended out of Shreveport, LA. In a few weeks he showed up, looked at the rack for a while and said Ill have to order a new part. I said fine. (How hard can that be? Right?) So here we are 5 months later, unable to use the middle rack because it cant hold any weight with the roller missing. Multiple calls to Whirlpool and A1 and we keep getting promises and runarounds that turn out to be lies. How hard is it to say go to your local Lowes and well authorize them to give to give you a rack from an in-stock dishwasher? Let Lowes wait on the new part! Sounds simple, and any other company would have done that, or told us to return it to Lowes for another one. But NO! Whirlpool just whines about being behind on parts, shorthanded, or lies about the part is in and its A1s problem now.So, today, same story. A1 says they need 2 parts. **! Its one part. Whirlpool says A1 has the needed part. Same old runaround. So, we just replaced our 14 year old washer and dryer with NON Whirlpool units. $2500 more in of appliances that Whirlpool could have gotten, but Im guessing they dont even care about missing and losing sells. They certainly do not care about warranty, parts, quality, customer satisfaction or repeat customers. Never again with Whirlpool! Beware!

Purchased 7/2015. LOVED it @ 1st being the key word. Notice grayish residue on clothing. Mainly on black. Towels discolored and lint on clothing. My kids were blaming dye in the detergent, & using Purex Crystals. I changed detergent to Armen hammer sensitive clear. Stopped using my beloved crystals. Wrong! Cleaned the rim @ the top of the agitator all the dirt & grime get ps trapped in the rims it helped some what. Additional problems occurred. From time to time started noticing unbalancing no matter the load size. Paint bubbling, peeling & rusting. The lid lock broken. Nightmare trying to get an appointment through Whirlpool. Referred to go to a dealer. Called Sears. Gave specific details whats wrong. Appointment 2 wks out. Service arrived, he had no idea why he was there. No info given. Then he said he doesnt have the part. He ordered it and said itll be sent to me approx 5 days. But wont be fix for another 3 wks. Same with 3 people from customer care. Informed this is not acceptable. Another problem now when unplugging it still stays on its hold electrical current. This can not be replaced until its deemed its broken & cant be fixed. They rather your home catch fire. They dont care about the inconvenience for 2 1/2 months.

We purchased a Whirlpool gas range for $600 in Aug 2015.. On May 2015 the range had an internal board failure (F2E0) and the panel does not control the oven or other features. We found out the part ranged from $350-$400!! Plus service installation! The one year warranty of course ran out but I think this is an outrage to sell an appliance that has such a poor electronic part. I have read a few similar complaints as this is also a Frigidaire model as well.

We bought a Whirlpool Refrigerator - Model ES5FHAXS in 2006. Right off the bat, a line in the back of the refrigerator was leaking. We paid for the repair. Next after just one year, the refrigerator would be warm and the freezer part ran super cold. The settings did not work. After much haggling with Whirlpool, they paid for someone to come out and repair it. It worked for several weeks then the same problem came back again. We argued with Whirlpool again and someone from AES or AAA came out. The problem was fixed but once again came back again after a couple months. We called Whirlpool again. This time was much haggling and arguing but got them to come out a third time. Once again, the problem was fixed but came back again after several months. The repair company stated that if they found it was something other than what they fixed, we would be charged. I said either it was not fixed right or the refrigerator is a total lemon. I said you will probably just say it is something else to cover your costs. Whirlpool acted like they did enough, even though 3 repairs could not get it right. If we paid or each repair ourselves, it would have been nearly the cost of the refrigerator and it still would not have worked. We bought a refrigerator back in 1992 and never had any problems after 16 years when we moved. The refrigerator was not cheap but could not do what refrigerators are supposed to do - keep things cold all the time. What a disappointment.

This diswasher is streamlined and elegantly desiged for any kitchen. It stays externally clean with easy to wipe surfaces. Easy to use controls on the top of the door that cannot be accidentally hit when walking by the item. Plenty of internal space for lots of dishes. Internal silverware rack is easily removalble and not in the way of dishes. It is extremely quiet when running, like a soft hum in the air. A real "bang for your buck".

Whirlpool Gold French Door - I purchased this fridge in Aug. 2009 (model GX2FHDXVQ00 22cu. ft. French door with bottom freezer). Paid 1800.00. The fridge stopped working after 5 years, but the freezer works fine. A fridge should last at least 10 years. I wont buy another Whirlpool appliance! JUNK!

I purchased a Whirlpool washer (WTW4800Q) in November 2011. Already, it has rust in the tub. The warranty does not cover this. I never really liked the thing since I have had it. It takes much too long. Lid locks and then starts over. Also, warranty is not good. I wouldnt ever buy their product again and suggest no one else should either. I loved Maytag before Whirlpool bought them out. Im putting this one on Craigslist and buying a real washer, a Speed Queen! Yes, Speed Queen has all metal parts and makes a home washer. Just have to find a local dealer. They are there.

We purchased a WRS576FIDM refrigerator from HHGregg in August 2015 and immediately had problems with ice maker and door having condensation on it. I contacted Whirlpool who had a tech come to my house and verify problems. Whirlpool replaced it with a new refrigerator in November 2015 and w/in a week it had awful condensation on the outside of the door, dripping onto the floor and pooling water. A tech responded to our house again and confirmed the problem with Whirlpool. Whirlpool advised they would be sending out two new doors for our side to side refrigerator and said we should receive them within 4 to 6 weeks from late November 2015. I asked Whirlpool to send us a different model because this is the second refrigerator of the same model that has the same issues. Whirlpool refused. I have spent countless hours on the phone with Whirlpool, HHGregg, and waiting for service appointments and my patience is getting thin. I just contacted them today 2-9-16 to inquire about my doors since it has been well over the 4 to 6 weeks Whirlpool said it should take to receive them. The Whirlpool rep on the phone had no information about the status of the doors and said that they would have to contact the service company to inquire more about the status of the doors. He also said that under special circumstances, it may take an additional two weeks for certain door orders. I once again requested a different model of refrigerator or a refund.I tried to get HHGregg to allow me to return the 2nd refrigerator just days after I received it since I was having the same issues as the original one I purchased. HHGregg said they could not since the 2nd refrigerator did not come from them. HHGregg said that they did not know why Whirlpool sent me a replacement refrigerator directly and added that normally the returns go through them. I feel like I tried to do the right thing by contacting Whirlpool for warranty work, but I feel that if I would have called HHGregg I would have been able to get a different brand refrigerator which is what I really desire after all these problems with the Whirlpool brand. I did purchase an entire Whirlpool kitchen set from HHGregg. The only problems I am having is with this refrigerator.

Purchased a new Whirlpool washer and dryer at Best Buy 6 months ago. We complained to Best Buy and Whirlpool about our clothes not getting cleaned. In other words, my clothes are coming out of the washer dirty. My make-up towels come out with make-up, my husband’s fishing clothes smells like fish and my son’s bike riding clothes is full of dirt. Whirlpool’s answer was the technician is reporting that the machine is working fine. Whirlpool told me to use different cycles and detergent etc. and I have done everything they ask, but my clothes are still the same. I told them this is a defected item. A washer should do its job - wash dirt and smells out. I want a different washer and they refuse to exchange this item for another washer after a second call to technician. Best Buy is telling us there nothing they can do for us. What has America come to? The manufacturers and dealers are selling to consumers and taking advantage of them by not responding to the needs of the consumer. In other words, we the consumers pay for product, take time from work and personal time to reports these problems and we get nothing back, just the run around. Is there something we can do? What can we do? This is very frustrating. We work for what we need. We pay for what we need and we dont get what we need. On the other hand, the manufacturer and dealer get what they need, our hard working money. What can we, the consumer, do to get our hard working money worth????? If anyone knows, please share your experience.

We purchased a new stainless steel Whirlpool refrigerator in February 2015. Within the first few days the fridge door handle broke off. Not that we have super human strength in our 60s but the handle connection is a very thin plastic. We put it down to the possibility that the warehouse or shippers may have banged it and perhaps we just didnt notice the initial crack. The handle was out of stock so it took 8 weeks before the new one arrived. This week the freezer door handle cracked! Same problem - cheap plastic handle connector doesnt withstand the vacuum seal. Whirlpools handle connection to the door is comprised of a 1/8th inch thick by 1/4 inch square piece of brittle plastic. This is screwed onto the door. In reality this needs to be metal. Enough said… Check out the handle connection before you buy this appliance. You will wait months for replacement parts as they cannot seem to keep enough of them in stock.

I love the large capacity of the washer. But something is turning my whites YELLOW! I have never had this problem in 40 years of washing clothes. All of my whites come out yellowish and I am getting what could be rust stains on heavier cloth (white denim). Also, I regularly used the soak setting on my old Whirlpool. That setting is not available in the Cabrio. I have tried catching between cycles and the drum is constantly emptied. I wish Id read these reviews before I bought.

I purchased a dishwasher and hooked it up. The reason I install products myself is I dont like people in my house. I dont know if they are there to help or inventory what they plan to rob from me later. It did not drain so I called Whirlpool who said that I probably hooked it up wrong. Whirlpool said that they would send a service man but if it was hooked up wrong I would have to pay for the service. The service man did arrive and had tattoos all over his neck and arms. (A tear drop would have confirmed that he was a murderer). The machine was hooked up correctly, the water pump was not working at all. The service company that Whirlpool contracted took 3 day to order the part. Yes three day to even order the part. Then another 10 days to get the part in. I called Whirlpool and they did not seem to care at all. My thought is, I am out $599 plus tax, and I have to wait 2 weeks to get my machine fixed, plus I have to take hours off work to wait for the service man and now I have to worry about the service man breaking into my house and robbing me and Whirlpool doesnt care. They should have to pay for the time I was off work and for the interest I lost on the money not being in my account during that two weeks. Whirlpool didnt care at all though. Worst customer service ever. Used to be that Made in America was something good. Not anymore thanks to companies like Whirlpool. Made in America = Garbage!!

Whirlpool gas range convection oven - I have only had this range for 2 weeks. Manual is sketchy to say the least. Purchased from LOWES - salesman were not well-informed. I have had to do a chat to find out information. Range looks great but performs poorly. Takes a while to heat anything even on high and on large burners. Grates are too heavy. I am sorry I did not see the editor review before I purchased. I have not used the convection so I cannot speak to this but my choices were limited when I purchased and I did not want a convection oven and other ranges would not purposeful for my use.

Purchased double range ovens. Enamel is flaking off within 2 years. Whirlpool denies defect. They wont replace it. Any other folks with similar problems? What can I do to have it replaced? I remember the old ovens and how the enamel just stayed and stayed and stayed. Never a rust or flaking issue in those old time models. Any expertise on how the enameling process may be compromised in the newer manufacturing process (cutting corners or costs). Any options for a class action here if a commonly experienced occurrence? If similar experience drops comments/review below as a one liner - just state enamel defect. That way can figure out the number of folks with issues. Id like to take action if given the opportunity, and more so if this is a common occurrence. Lawyers are costly for one-off complaints, but there is power in numbers (think United Airlines).

April 14, 2014: Bought Whirlpool 30 electric stove WFE361LVQ Sept 2009, $545 - only 4.5 years old. While broiling, got strong electric burning smell, filled house. Broiler and oven stopped working (top burners OK). Opened back and found BURNED CONTROL BOARD corner and BURNED OVEN FEED WIRE. Definite SAFETY HAZARD. New panel $289 and wire harness $105 + 25 = $418, discount to $375, + service call to find out why/install guarantee $129 = $505. Ridiculous! Will contact Whirlpool for recall and compensation. Hope other recent entry sees this. (How respond to specific entry, since this response pulls us away from listings?) Meanwhile, well buy any other brand replacement.

We have several Whirlpool products in our home currently and have been very satisfied with their performances. We have their fridge, stove/oven, microwave and dishwasher, all of various ages. We purchased them from a local big box building supply company and installed them our self. The installation directions are clear and simply for the average D-I-Yer. We would recommend Whirlpool to everyone shopping for these home appliances.

We purchased this washer (Whirlpool Cambrio #WTW8000BWO) in December of 2014. It is now 3 1/2 years old and while the washer worked great til just recently, we now have to purchase a different one because this one will cost too much to repair. We did not get the extended warranty. I have since read that the Cambrio has had a lot of problems. Always check the long term owners and what they have to say about the item, would never have purchased this washer had I known what the problems were and that they even were having them they should have taken it off the market til they got the situation fixed.

I had kenmore in long term until we decided to change the brand Whirlpool. We just saw want to updates to change the color. It was good price on special day. I have no problem with the stove. I like there is size of pots from small to large pot of size.

Informed that because washer was 1 year out of warranty. It was 2 years old. Parts were not guaranteed. Cost to repair $400.00 including labor. Maytag Store came to my rescue and it only cost $200.00. 2 years later, washer is not filling with water correctly. Have mixed feelings about repairing or replacing. If replacing, how to select a reliable washer. How do you select, if when we purchased this washer it was rated very high. Whirlpool does not help with any issue. They were extremely rude. Felt helpless dealing with them. Need a new washer and have no idea which brand to go with.

My dishwasher is really a simple basic dishwasher. It is efficient and does a good job of cleaning. You can put many items in the top and bottom and the utensil basket can be moved for better cleaning or more room. If I had one complaint that would be that it is a bit too loud but other than that it is wonderful.

The dishwasher is noisy and the latch which holds the soap, at times sticks. When we think it is done and ready to unload we need to run it again because the latch that holds the soap DID NOT open. Not good.

I chose based on the current ratings of the machines. They look nice and they can handle large loads. I think EPA has changed wash machines to be back into the 1920s. I put my clothes in and there is no agitator in the center. My clothes come out twisted tightly into little round circles or balls, not much water but now it takes over an hour to wash my clothes. So we are conserving water but using more power, I also have to iron sheets and clothes because they are so twisted and wrinkled. I used to stick my clothes into the washer, select a cycle and go on my way and now I have to answer 5 other selection options, if I dont hold the button in long enough it just turns off.Have we all lost our minds, I think this is going backwards not forwards. I have talked to other women and they agree with me, we HATE these new washer and dryers. The dryer is a little better but not much. Also the tops are concave so your laundry basket falls off, and you cant put your soap on the dryer which is where I am used to having it. Now I have to clean my washer every 30 cycles, iron and it takes all day to do the laundry, yes and they call this progress, really!!! I purchased the Whirlpool Cabrio W10607 425A- SP and dryers Whirlpool W10680129C-SP, these are full size and have the steam options on them and are side by sides.

Whirlpool side by side with in door ice maker W10281961D - I purchased the refrigerator 10-2013. Within 9 months all of the food in the refrigerator side was freezing. Unfortunately, I did not purchase the extended warranty so I would turn up the temp control every 24 hours as suggested in the manual. The water maker then stopped working. I am disabled and money is tight, but I was wasting so much by throwing frozen produce and eggs away and was worried about thawing meat on the counter since it was not possible to in the refrigerator.I finally broke down, called Sears, purchased the warranty at that time, which was $259.00 and when the repairman came out we found out the damper was broken, thus causing the food in the refrigerator to freeze and the motherboard had went out, thus causing the temp controls not to work. The extended warranty had a $500 max, so we had to pay an additional $120.00 out of pocket. It is working fine now, but in my opinion, it should not have stopped working as quickly as it did since it was an expensive purchase to start out with.

Bought in October 2014. Died December 2015. The previous Whirlpool microwave this unit replaced was 10 years old and carried a 5 year warranty on the magnetron. Imagine my dismay to find out this unit carried only a 1 year warranty on the magnetron. So 2 months past warranty expiration Im left with a dead unit. I performed elementary troubleshooting. The unit has a fuse on the 120 Volt input. But the unit must be disassembled to gain access to the fuse. So what SHOULD be a five minute job turned into an hour and a half. The fuse wasnt the problem - replacement fuses blew like popcorn. Fuse placement within the unit without regard for service considerations is a poor design.To their credit, Whirlpool agreed to cover the cost of repairs if I would pay for labor. I agreed. A tech came out and looked at the unit. He said that he would have to order a bunch of parts and that he would be back in contact by the end of the week. Three weeks went by. There was no call from the tech; my messages on his voicemail generated no response. So a couple of days later I purchased a replacement from a competing manufacturer.

Dishwasher leaking thru the diverter motor; apparently the gramet # WPW10195677 gets worn out and starts leaking. They have discontinued the part and can no longer be found. I call Whirlpool and all Parts supplier in my city. Obviously this is something that happens with time (5 yr old dishwasher) and is something very simple to change. But if we cant find the part....what are we supposed to do. Also my dishwasher rack has broken 2 years ago and is holding with zip straps! Horrible product!

Near the beginning of September I started having trouble with my dishwasher. I called for service to be informed it would be a week before someone would be able to see to my broken dishwasher - which of course is a long wait just for a diagnosis call so decided to call another provider to get my dishwasher fixed in a more timely manner. The repair person informed me that it was the control panel but he suggested we call Whirlpool in order to have it fixed as the part should be covered under warranty. Much to my sadness I had to call again for an appointment with Whirlpool to find out I would wait for a week for a repair person to come out even though I already knew it was the control panel and asked them to order the part right away.Sept. 13 repair man from Whirlpool affiliate comes to my house for about 10 minutes to tell me what I already knew - it was control panel and maybe 1 other part. Cost $99.00 for just 10 minutes - Wow! Then the repair person said he would order the part right away /estimated to be back Monday September 19th great! Two weeks go by we have heard nothing about our part or possible repair of our dishwasher. Call Hurst appliance to see what is happening to be informed the panel is on back order - and they have no clue when it will be available. I should call the manufacturer. Call manufacturer to be told part might possibly be available - Oct 5th - from the United States from somewhere out east in Canada. Who knows? Oct 5th comes and goes as of Monday October 11 have heard nothing about my dishwasher and when it will be repaired - phone manufacturer - by the way which is in Tennessee. What a joke!She says the part is still on backorder but that a replacement part for the back ordered part is miraculously available - she couldnt tell me when that came about, so still have no clue when my dishwasher will be fixed. They have offered to reimburse me the $99.00 service call, but seriously should it take over 6 weeks to have your dishwasher fixed. I still have no clue how long it will take for the part to get here and installed. For 2 cents I would return all my KitchenAid appliances but especially my dishwasher. $99.00 does not appease me. I would like them to cover the labour to fix my dishwasher or a new dishwasher. What garbage and asked to talk to someone higher than the supervisor Gabby of the customer service dept. and was told she is the highest person in Whirlpool I could talk to - thats a joke. Shame on Whirlpool!

I had this same refrigerator in another home and had no issues, this particular one now I have nothing but issues with it. It seems that the quality is not consistent. First the ice maker was not working, then the freezer light burned out and now there is extensive frost build up in the freezer. The refrigerator is only 2 years old!

I bought a Whirlpool refrigerator from Home Depot. It didn work. I had to wait for a week to get a new fridge.. I also bought the 5 year warranty -- its not worth the ink its written with. MAYTAG DOES NOT ANY CUSTOMER SERVICE. THEY DONT KNOW A THING ABOUT CUSTOMER SERVICE.

First time owner of a Whirlpool range and will be the last time. Nothing but junk! I liked how the top grates were and electronic ignition. The knobs turn too easy and often when bumped will turn gas on without igniting. Very dangerous. The oven grates guides rusted almost immediately making it difficult to pull racks out. The oven light works sometimes. The glass on the oven door at the bottom came unglued. The bottom door under oven is a total waste. No use for it. In my adult life I have had different brands but this is the absolute worst and will never recommend this brand to anyone period.

I have had to replace my Whirlpool 50-gallon hot water heater 2 times. First time it broke, it caused thousands of dollars’ worth of damages plus Im out a $760.00 deductible. I had the last one just over 1 month and couldnt exchange it at Lowe’s because it’s a few days over a month. So I had to get return authorization before I could return it again. I went through speaking to a hateful CSR. After calling back again, the lady, a real nice lady, helped me. I will never buy another Whirlpool product again, and if anyone is smart, they will stay away from them too. Hateful, hateful CSR. Beware.