We have had our washer just over a year when the plastic hose that fills the detergent tray began leaking. The entire assembly is plastic and poor quality. Whirlpool customer service says since it is after 1 year, that I would need to pay for the parts & service ($489). I would not recommend this machine or anything Whirlpool.

After less than 3 years it was the bearings, of course. Then, being handy and not stupid enough to pay the $500 for the whole piece of crap Whirlpool/Maytag tub, we bought bearings from the PartsDr. We just didnt dig deep enough to know that the strators on these things are made out of the cheapest Chinese plastic and are cracked in the SAME TWO PLACES EVERYONE ELSES IS!!! Imagine that? Will scrub my clothes in a river on rocks before I ever buy a Whirlpool/Maytag Chinese again. All front load seem to have the same problems but at least some other companies admit it and are trying to correct it. Will research and as with everything else stay away from the USA/Chinese rusty, corroded junk.

I purchased Whirlpool washer in Dec.2017 and used it in winter months only (Nov to March). It kept leaking and had to get appliance repair service for $50 and was told that machine is defective and whirlpool should repair it or replace it. I phoned whirlpool and they told me I have to use their appliance repair shop to evaluate the machine for cost of $130. The inlet valve was leaking and needed replacement for a cost of $253.55 and whirlpool shirked all and any responsibility. Dont buy whirlpool as it is not a good product and service is poor.

Whirlpool WRF992FIFM00 - Purchased new April 2017. Its October now. Service has been called 7 times so far. Ice maker has not worked since day 1. Fridge leaked all over the interior around the third month. Compressor went out in 5th month. Compressor replaced 2x so far. Every component piece was replaced on 5th month. Still no ice. As I write this compressor getting ready to go out yet again. Paid almost $3000 for this piece of crap. On first name basis with technician. He tells me that his guys work on this particular refrigerator CONSTANTLY. So far I have lost over $1700 in food and wages (leaving work to meet technician). Currently battling Whirlpool. My next step will be legal action if they do not refund or replace this stainless piece of garbage.

My KitchenAid side by side refrigerator/freezer is a beautiful thing, shiny steel surface, gleaming white inside. However, its made poorly. The ice cube maker compartment broke and the replacement came without any installation instructions. It was hard to figure out and I broke it. Now, everything in the refrigerator is freezing and changing the temperature on the digital panel makes no difference. McKinneys appliance, where I bought it, no longer has a refrigeration technician and they referred me to Whirlpools 1-800 number where I supplied some information and sat in my chair on hold listening to music for a half hour before hanging up.The recording on the phone suggested their online chat where I was asked the same sorts of questions and was told I would get the answers I wanted by paying $5.00. I had no idea what I was getting into but I didnt pay, just terminated that inquiry. Feeling cheated by the company whose product I had mistakenly purchased. Im now running the risk of a technician visit, sometime between 8 am and 4 pm a couple of days from now. I have to be prepared to wait around all day for somebody to look at my refrigerator, charge me a lot of money and, from what Ive read online, potentially see the problem return in a very short space of time.

My experience w/ Whirlpool has been disastrous. Whatever you do read the reviews on products before purchasing, do your homework first before purchasing any major appliance. Whirlpool company and its employees are a joke. We are paying consumers and spent our hard earned dollars to support a company that could care less about us and our problems with their products they sell to us which are a piece of crap. I purchased a refrigerator made by Whirlpool from hhgregg in Oct 2015, which took 2 months to get it delivered. The refrigerator is not a year old yet, and cannot get anyone to come out to repair it. I have called Whirlpool numerous times, and so have my husband to come and repair a refrigerator that is less than a year old.The ice maker stopped working. Then I came home and discovered that the refrigerator is not cool, and everything in the bottom freezer had almost thawed out, and a repairman was supposed to come on August 31, 2016. It has been hot as Hades, during August, Sept, in the high 90s and they had the nerve to call and say they had to order the icemaker and when it came in someone would be out to fix it. I called the company in Maryland to find out what part did they order because a technician hadnt been out at this point to determine what part needed to be replaced. I called Whirlpool, and yes was put on hold for 45 minutes each time, and when I asked to speak to a manager, I was told that the manager said I could call a repairman and they would reimburse me up to $150.00. I replied That that is not my job. Your job is to send a repairman to fix it.The name of the company that they gave me and the phone number is located in Maryland, I live in the state of Virginia past Richmond, 3 hours away. Then I was told by the company in Maryland that they dont have technicians to Repair Whirlpool Refrigerators. This is totally unacceptable. It is Sept 19, and since August no one from Whirlpool has been out to fix it, neither have they tried to rectify the problem. Bottom Line, DO NOT BUY A WHIRLPOOL PRODUCT, not from hhgregg, Sears, Home Depot, Lowes, anywhere because this is how they treat customers. I have an 88 year old Aunt that lives with us that were responsible for, and she cant even get a glass of ice cold water from a brand new refrigerator thats still under warranty. Whats wrong with this picture?

I cant begin to tell you what a pile of crap my Whirlpool range with Aqua Lift cleaning is! We purchased it brand-new and it is the slowest oven on the planet! If I want to cook a pizza I have to call home 30 minutes in advance so the oven will be 1/2 heated up. The Aqua Lift has never worked and the company has the most abhorrent customer DIS-service Ive ever had the misfortune to deal with! I hope these scumbags go bankrupt!!! AVOID anything Whirlpool! There is a class-action suit in the U.S. over what a slime bag bunch of crooks they are and how their Aqua Lift technology has NEVER worked!!

My complaint no. ** date 11/07/2014 till date 06/08/2014. Its noted solved by services department after 100 calls by me. They Reply no parts available from company so if you buy washing machine, be careful about Whirlpool washing machine.

Our 2005 whirlpool duet washer steel drum and plastic tub broke. My husband diagnosed the problem and opted to fix it to save money. The parts are under warranty but you still pay labor and technician visit running up to $250-$300. The plastic tub was obtained only if we paid for it $100 and the steel drum they sent under warranty. The plastic tub has a hole with a black plug and sensor in it. There is a discrepancy in the measurement of the old tub and new tubs hole that is slightly larger, therefore when installed a steady stream of water leaks out. I now have 3 plastic tubs as that was their solution, to send more of the same that did not measure correctly. An investigation was done to determine they were the correct parts. As asked we had a whirlpool technician come to verify parts were correct and being installed correctly and the parts sent would not fix the machine due to the hole discrepancy. Many calls were made to whirlpool and they continue to give me the runaround. They now are not taking their technicians information. The technician has given the information to 3 sales reps in the new england area and made several phone calls to whirlpool and no one is willing to give us a solution.

I bought 2 Cabrio washing machines for my two homes along with the matching dryers. They worked for about 3 months, then the washers displayed OL Error during any wash cycle. I tried to contact manufacturer and have not been able to get service without charge. After reading the many posts I am not sure if I should dump both or start investing $$$ in service calls.

Went to Lowe’s, as my old fridge died. Gets delivered & guys wore masks. After they leave the NOISE of fridge I could hear in bedroom! I called right away had to wait for a replacement from XPO about a Week. Guy shows up stinking like ashtray, No Mask to “repair” my brand new Loud Fridge. Heck no was to get replaced. I called Lowe’s 3 times & XPO twice. It’s now June 4th. I’m still waiting! 25cubic Serial #HRX0654908. Horrible customer no service!

Whirlpool refrigerators with bottom freezers have a major defect in a tiny drainage hole hidden inside the back panel. The hole easily gets blocked with bits of debris during manufacturing or with a few bread crumbs, then it freezes shut. Then water ends up all over your floor. You cannot fix it yourself as you have to take apart the whole freezer. The repair bill is huge. This will happen often. Check on the internet and YouTube to verify & you will see that this happens to everyone with a Whirlpool. Also your floor will be ruined if you dont mop it up every few days until the repairman arrives! Stay away from Whirlpool!!

My dishwasher is really a simple basic dishwasher. It is efficient and does a good job of cleaning. You can put many items in the top and bottom and the utensil basket can be moved for better cleaning or more room. If I had one complaint that would be that it is a bit too loud but other than that it is wonderful.

They have sent three specialists to look and assess the Whirlpool washer and dryer that I have. Both stated that the washer does not function correctly; the last repair man stated that he had seen many like this and they have a history of unreliability. I would like my money back, not a repair, as they do not even use just cold, but a mixture of both hot and cold. I had bought them specifically because I thought they only used cold, which was stated by Whirlpool. This is wrong advertising. I would like my money back. I still have the receipt and I am seriously unhappy with the washer and dryer, period.Since I cannot use the machine, which I had bought for $1600.00, the washer and dryer is now sitting in my basement. While whirlpool is saying that they wont take back the washer and dryer even thought it has a warranty. I had paid it in cash and I do not see why I should be forced to keep a broken washer and dryer set. I will contact my lawyer to consult this issue with Whirlpool.

Whirlpool 2 Cu. Ft. Stainless Steel Over-the-Range Microwave - My wife and I have just remodeled our kitchen and we bought all the Whirlpool appliances, fridge, stove and microwave. We have had them for about 3 weeks now and now the display on the microwave just stop working. I just cant believe this. Its going to be a real pain now to remove this and replace it. Has anybody else had this problem and I wonder if its even covered under its warranty.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

Cleans average compared to previous dishwashers. Does not dry well even on high heat dry. Cycle takes about two hours and I have to run it during the day because it is too loud. The price was good, but I wish I would have bought a little higher grade.

Whirlpool Cabrio Washer model # WTW6800WW1. Bought it July 2009 and it broke Jan 2017... 7.5 years old. Cost to repair $715.00. The technician recommended that I just go ahead and buy a new one... not worth the while to fix. I paid $900 for this machine in 2009. This is an expensive machine, not a cheap ass one. Shame on Whirlpool for selling products that dont last and for making it unaffordable to fix.

Bought a new $899 dishwasher 7/2020 and it stopped working 10/2020 And it’s been weeks and now I’ve been told it will be another 21 before they can replace it if at all! #whirlpoolusa #whirlpoolcorp Customer service lady was rude with an attitude.

Brand new dishwasher and first time I started it I noticed the timer showed the cycle taking over 3 hours. When done I opened the door and there was some water in the bottom and the door was very wet. Dishes had not been washed. A glass that had turned upright had no water in it. The soap pod was still intact. I started over again and the same thing happened - two more times. The silverware is not clean either. Its going back!!! Im sure there will be resistance but we will deal with it.

I bought the top-of-the-line Whirlpool top-loading washer and havent regretted it for a minute. This machine washes everything from the most delicate to the most bulky and heavy and does an excellent job of it. It saves about 1/3 of the water my rotary agitator washer used. What more could I ask from a washer. Incidentally, also purchased the largest front-loading electric dryer Whirlpool makes and never have to hold a load of wash until the dryer finishes the last load...a real time-saver.

The Cabrio is the absolute worst washer that Ive ever owned! No matter what combination of setting I use, my clothes come out dingy, all twisted and wrinkled, and full of lint and detergent residue (I use liquid detergent made specifically for HE washers). Every setting runs for over an hour. So much for high efficiency! What it saves on water it more than wastes on electricity!! More often than not, the entire load becomes enveloped in one of the items to create one huge ball. A t-shirt stretched to encompass the remaining clothes into a perfect sphere! When that happens, some of the laundry in the middle of the big ball is barely damp. The dryer is just as bad, even the towels come out wrinkled. How is that possible? And again, it takes over an hour to dry a load.Whirlpool customer service is awful. When I called to complain, the agent began schooling me on how to wash clothes. Im 66 years old, Ive washed a few clothes in my lifetime and have always prided myself in my white whites and bright colors. I have a new house and the builder provided all the appliances. Based on my past negative experience with Whirlpool products and their customer service, I would not have purchased Whirlpool.

The repair technician just left telling us that our Whirlpool Cabrio washing machine is fine. It is a little over a year old, makes LOUD noises as it runs, doesnt get the clothes clean and often doesnt even get them wet. The clothing sits above the water and comes out with pet hair, soap and dry spots. We use it the way the manual directs but it seems to be a totally defective machine. We sure wouldnt sell it to anyone nor give it away to some poor unsuspecting soul. Guess it needs to go to the dump. Shame on you Whirlpool for taking advantage of so many of us.

I bought washing machine in March 2012. Since the date of purchase, the machine is not working properly. Even though it is under warranty period, I have to spend money on my own to repair it. Whirlpool customer care never responds. When I ask to give the number of higher authorities, customer care denies to do that.

I have the Whirlpool Gold microwave model GMH3204XVQ-1 manufactured in May of 2010. The plastic around the lower door handle is cracking (currently in 4 directions from the handle) and the plastic on the side of the control panel is cracking in the center area and lower side. Neither of these area experience abnormal stress in day-to-day use. Unfortunately I could not get a good photo of the other crack on the lower corner of the control panel but included the one on the side in the middle. I contacted Whirlpool customer support about 1-2 months ago and to date, have not received any type of response or concern from them about this issue.

Very pleased with my Whirlpool dishwasher. It is not the top of the line but does a great job of cleaning my dishes and is very quiet when running. Whirlpool appliances have been very good to me.

My oven is less than 2 years old. The blue enamel has had cracks for over a year & was told its cosmetic & theres nothing that they can do about that. Now its starting to pop off. I found a few slivers in a vegetable dish! Now I cant even use the top oven because of this! It seems to only affect the bottom of the top oven. I feel that the temp may be getting too hot for the blue enamel which is another safety concern. I have contacted Whirlpool/KitchenAid to be told that if they send out a repair person he would just use a marker on chips. I was told they would give me an employee discount from $3000 to $1800 to replace but I would have to act right away for that price! Really? My oven is only 1 & a half old.When I started researching this problem I am having I found many complaints of people having the same problem! As a consumer I feel so mad & frustrated that they are not doing anything about this since its an ongoing complaint from so many dissatisfied consumers. I do believe it is a safety & health risk now that its showing up in the food that has been cooked in that oven. I would urge anyone thinking of buying a Whirlpool/KitchenAid cobalt blue enamel oven not to! They will not stand behind their product & you will have to replace at your own expense. Shame on you Whirlpool!

I purchased a Whirlpool refrigerator in 2012 and now it does not work and Whirlpool says a 1300.00 refrigerator only has a one year warranty. Please do not purchase a Whirlpool brand because they do not live up to their brand name.

We purchased a Whirlpool Cabrio about 3 years ago. Have never really like it. It doesnt add enough water to the wash cycle unless you use the bulky setting, which fills the tub up the entire way, so wastes water. It would have been nice to choose your water level like you could on the old machines. Now it wont drain completely and wont spin totally. Ive tried using the drain/spin cycle 2-3 times extra and it still wont spin all the water out. Ive noticed that there is still water in the drum, you can hear it slosh when you move the drum, so I wonder - has anyone ever been told there is a filter in there somewhere that might be clogged keeping it from draining completely? My husband thinks that maybe all the water in the bottom of the drum is not letting it spin because its throwing it off balance. And yes, it stops before the cycle is complete and just sits there and blinks and you have to unplug it to clear the cycle. What a pain. We will never again buy a Whirlpool and I absolutely do not recommend Whirlpool washers. I have a Maytag as well and have not yet had problems with it. Bought it at the same time we bought the Cabrio (2 households). At least the water levels in the Maytag are a little more normal. You can wash more than 1 pair of jeans and get them clean in the Maytag. For those of you with the problem of the clothes not smelling clean - try running the clean cycle with a cup of bleach about once a week. No clothes in it - just a cup of bleach in the bleach dispenser and nothing else. Works for us.

Offers a long-lasting, high-quality finish that resists scratches and rust. Provides smooth, efficient operation and reliable combustion efficiency. The ECM motor provides computer-programmed airflow for greater efficiency, humidity control, reduced noise levels and increased comfort. 2-Stage Gas Valve System Allows the furnace to operate at a lower output setting to more efficiently control your home’s comfort in relation to the temperature outside. Reduces gas usage by 30% on most days. Durable, Baked Polyester Pre-Painted Steel Cabinet Offers a long-lasting, high-quality finish that resists scratches and rust. Aluminized Steel In-Shot Burners Provides smooth, efficient operation and reliable combustion efficiency.

Bought a Whirlpool Cabrio Washer, which I see has MANY complaints. I had a problem with the F1 issue during the first year. Same issue and I was also told Whirlpool knows it was bad design yet they refuse to help the consumer in anyway. Maybe 50% a new WP washer. Upon my call they will fix it for 389.00 and give a 1 year warranty again. Im no longer confident in WP products.

Purchased a Whirlpool dishwasher less than 2 years ago, began noticing a mildew buildup inside. Cleaned it, and bought dishwasher cleaner products, but the problem continued. Realized the dishwasher heater was not working. The dishwasher was staying wet, therefore causing mold. Called appliance repair, and spent 3/4 of the price of the 2 year old dishwasher to repair it. The control box malfunctioned. I was told by the repairman that that was unusual. At the suggestion of the repairman called Whirlpool. I was told since it was beyond the 1 year warranty they will comp us nothing. As a consumer I have no other recourse but to warn others, and to never buy a Whirlpool product again!

I have both Whirlpool washer and dryer. These are my second set. Whirlpool is reliable & long running. I love this brand! My dryer is six years old and the washing machine is nine years old. Never a problem and they do about six loads a week.

Purchased over range microwave WMH31017AW-2 from Best Buy Mar. 12, 2015 and after installing it noticed code Door appeared and that there also was a dent on side. They replaced on Mar. 19 and we had the same Door code problem. Called Whirlpool and they sent out a Tucson repair tech and he ended up coming out at least six times changing 3 switches, 2 cams, 2 brackets, control board, and line filter. Still had problems and Whirlpool requested he call their tech and he did and they told him to make the same changes and he told them he already did all that and there still was a problem. Then Whirlpool told him to switch some wires on control board which did not solve anything. Then second thing they told him was to file and clean door brackets which also did not solve the problem. We called back to Whirlpool to tell them we did not want this defective microwave any longer as all these repair trips were not solving anything. They wouldnt give us a answer right then and said they would call us back 24 to 48 hrs and we are still waiting. We will never recommend Whirlpool to anyone nor ever buy from them again.

We purchased this Gold Series Whirlpool Dishwasher about 4 years ago. It worked very well up until April of this year. At that time, the main pump stopped working and it has to be replaced. There are just two of us in the household so the dishwasher was only used 2 or 3 times a week. We also kept it very clean with no build up. The gasket around the soap dispenser came out and one of the wheels fell off of the bottom rack. We just feel that 3 1/2 years is too soon for a major appliance to stop working and fall apart, especially given the light usage.

I bought my Whirlpool Convection oven in mid August 2019 from Lowes. I have had to call no less than 5 times about my NEW oven which I am extremely remorseful of buying. I am so unhappy with my experience mostly due to my expectation that my new oven would have been able to meet my demanding needs baking and cooking. I would have thought that it would have lasted longer than 4-5 months. The bottom left hinge is faulty which I am told is an undocumented problem for this particular oven. I noticed that it was having a problem when the oven wasn’t quite making a seal. Slowly it got worse until now it makes an initial click then I can open it about 5 to 6 inches and then have to lift it up so that I can open it without making a horrible noise and a dent in the frame.The first time I called was on Saturday Jan 4th. It took me 1 hour to get through to speak to a person. I asked why I couldn’t get a new door to the oven and they told me the hinges have to be installed separately because this model is made to be able to take the door off for cleaning purposes. They set me up for service on Wed Jan 8th between 12 and 4p. I wasn’t as unhappy at this point. I even got a text saying that the appliance company would be coming between 12 and 2. At 12 when I woke up after working nights, I got a message saying that they hadn’t received the part yet and that there would be no point in them coming. I called Whirlpool again and they told me that the part was on backorder and that in fact the part had to be fabricated and it may take up to 10 business days but that they would have the part sent directly to my house. By this stage I am very unhappy.I called back this morning and told the person that I would rather have a new oven or my money back and that my less expensive and less decorative oven that came with my house lasted me 20 yrs. I get a lot of “I’m sorry” and “I apologize” but that doesn’t fix my problem. I also told them that now the frame of the oven is being dented so I am going to have a less than perfect appliance which is no fault of my own. The only info the person could give me is the tracking number of the part they were able to locate which would be coming Fedex.I tracked it and it was due to come no later than Tuesday night. So I called the original service company in my area who told me to call to set up the service time when the part came in. I figured I would get a jump on it and call. They told me that they were all booked up this week and I would have to wait until next week. Do you think that this is how your customers should be treated? I feel as though I am being punished by choosing to buy an appliance from Whirlpool. I then tried calling back to set up an appt with a new company but the wait time was too long. I had just worked nights and needed to get some sleep. I called back this afternoon and again had to explain the whole situation AGAIN. I was able to set up an appt with a different company for Monday between 12 and 4 which happens to be on Martin Luther King day…so I am hoping it is not a mistake.Do you think this is fair treatment for a customer who just bought a brand new oven less than 5 months ago? Would you like this type of service? Would this give you any confidence to buy products from Whirlpool? I don’t believe that I would be able to recommend Whirlpool in good faith. The people who I have talked to have never been rude or disrespectful however, I feel as though my unhappiness is just par for the course. I feel as though it is just my tough luck and “oh well so sorry” instead of the attitude that you want to make everything right as quickly as possible. I ask myself if the problem was the store I chose to buy from? If I should have gone to Sears and bought one of their products or where I went wrong.

This washer has been a lemon since the day we bought it. Always leaves marks all over dark clothes. Had to have a part replaced before we owned it a year & repairman from the company said they have to replace that same part every time they go out so they carry them on the truck. Latch broke after owning it for less than 2 years & now it no longer spins water out of clothes. All this & we havent even owned it 3 years. I had a GE washer for years when I first got married & had children. Never had problems like this. Paid it off on Monday & on Friday it became a piece of junk. How is Whirlpool getting away with this misrepresentation? I dont even see how they can call it a washer.

Whirlpool convection/microwave GMH6185XVS - In 2011, we purchased a whole new kitchen for our home with the top of the line Whirlpool products. The sorry side of this project was our microwave. This product has been terrible for us! It has been removed from our wall 4 times for failing... and four times we have gone for weeks at a time with a big hole in our kitchen wall!! All of the failures were due to the microwave not heating food or drink, and all, according to our local dealership, were for various different reasons. Again, it has failed and our local appliance center who we bought everything from does not want to deal with it anymore. I dont blame them... I dont either!! It looks beautiful up there above our range telling me the time of day... My wife and I are older adults and take very good care of everything we own. There certainly has never been any abuse to this product (not to mention we spend half our year at a winter home so this microwave only is used for 6 months a year). I contacted Whirlpool customer service about the reliability of this product and their response was that it is now not under warranty and we should deal with our local store about repairs. I have a small Sharp microwave sitting on the counter below this crappy excuse for one that stays there all the time in anticipation on the Whirlpool going down!!! The $60.00 Sharp never fails me!! This was our 2nd time around purchasing all Whirlpool products for our house. We did the same thing when we built back in 1990. All appliances performed as they should have back then. It seems Whirlpool integrity has gone downhill. I will never buy another Whirlpool product nor I will recommend to anyone I know to do the same. Good luck to anyone who purchased one of these.

Top load stackable Washer dryer - Model number YWET 3300XQO. I had two floods with the same washer dryer unit. The first flood occurred in April 2012 and thousands of dollars were paid to repair the home that was damaged due to this flooding. The second flooding happened in October 2012 with the same machine at the same home. This time there were other Whirlpool owners that also suffered with the same issue with the same model Whirlpool machine. Whirlpool acknowledged that they will pay out to fix the damages and the deductibles but to date they are simply playing games on paying out. This is 15 months after the first flooding happened.

Ive had it with Whirlpool products. I am now getting rid of my third Whirlpool microwave in just eight years. Every one of them had the same exact problem and Whirlpool continues to deny there is a manufacturing defect. Each of them developed a hairline crack extending through the bottom screw of the door handle to the glass on one side and the outside door frame on the other. They will do nothing about it and claim it is just a coincidence. No more Whirlpool ever!

Long story short, we replaced a very old Whirlpool water heater with a new one a couple of years ago... We have had nothing but trouble. First, pilot light wouldnt stay lit. Found out that it was defective.... Whirlpool DID offer a no cost conversion kit. Had to pay shipping and installation costs. Have had the plumber out four more times to try to ANYTHING to keep it lit.... No luck. He even spoke to a Whirlpool tech on the phone and followed his advice. I have filed an online complaint with Whirlpool and the site stated that I would hear back within three working days. Guess what.... no reply. I have four other Whirlpool appliances that I love, BUT as they wear out, I will NOT consider Whirlpool.

I thank the folks at Whirlpool for building a washer (Cabrio tub bearing failure) that lasted 22 days just shy of four years, better than the Whirlpool Duet that lasted 14 months, tub bearing failure also. Now I have high confidence that Whirlpool pre-engineers failure into every washer they build.

My Cabrio washer worked fine for approx 3 years. Within the last 9 mos there has been one repair/replacement issue after the other: pump, computer board, bearings, seal, etc. Whirlpool takes no responsibility. Worse purchase I ever made.

I purchased a Whirlpool refrigerator in 2014. It is a side by side with ice maker in the door. About 8 month ago the ice machine stopped working. I called an appliance repair center and they diagnosed the problem as being the control board for the ice machine. After only 3 years this stopped working? I gave them to OK to fix it. A few days later I was informed that the part is on backorder for a few months. Well a few months has become 6 months and no part is available. I contacted Whirlpool and they called me and promised a solution, but then they never contacted me again. So it is almost 7 months later and I still have no ice. How can a relatively newer product break down and then not have a part available? Whirlpool absolutely does NOT care about their customers and does NOT back their products. Stay away at all costs.

I purchased this washing machine December 16, 2011. I paid $737.07 for this machine. 14 months later I had to repair the top of it which cost me $255 for the lid which the plastic around the lid was cracked. I had to pay $136 installation fee and two years later the exact same thing happened again, the plastic cracked. I have contacted Whirlpool which took a complaint - said that was all they could do. Ive contacted the store where I purchased it, they can do nothing. I read online there are many complaints about the lid on this washing machine. It shouldve been a recall. I will never purchase a Whirlpool product again. I will not pay to have it repaired again. I will give it away and purchase something else not whirlpool and not from Lowes. I expected some kind of compensation from whirlpool on this. I have all my receipts.

Whirlpool sent out a repairman to fix my range. I had it for 3 years, and one day I was baking cookies in the lower range and boiling water for pasta on the top left burner. There was a very loud pop, a bright flash in the glass top where the back left burner is, then there was no power to the range or oven at all. No clock display, burners would not work, oven would not work, nothing. As if it were unplugged. Of course, my warranty was about to expire in approximately 6 days (go figure) so I called the customer service line for repair. After 2 hours of back and forth with 3 different people, I finally had a technician coming out 4 days later. He shows up, takes about 35 minutes to get the glass top off, then says to me that he needs to order a part for it. This will take a few days. Ugh. Fine. 3 days later, part comes in. Same guy comes back out, fixes it. Ok.Up and running fine for about a year and 2 months. Then... POP! It happens again. Same scenario, different menu. (I was cooking breakfast). Now, warranty has run out and I have a $1,300 piece of scrap metal sitting in my kitchen. Worthless. My old KitchenAid stove was great. Had that thing for 13 years. Never a problem outside of replacing a $68 heating element one time. I paid $450 for that range. Tossed it out for this bells and whistles newer stainless steel glass top range/double oven. Regretting that tremendously. Whirlpool will be on my do-not-buy list for any appliance from now on. Didn’t even last 5 years. Oh did I mention the service call cost me $85? Yeah... Garbage!

The average life of a refrigerator is 11 years. We purchased a Whirlpool convertible refrigerator (Model EL7JWKLMS02, Serial # EWR1339731) on 6/12/04 from the Lowes here in Visalia, CA. The first delivered was DOA and Lowes delivered another. That should have been a warning sign. We have had several problems with the product, as early as 2006. All repairs went through Sierra Appliance & Franks Appliances.We are now in the market of another refrigerator to replace this one. We have had to have freon added now for the third time. Sierra Appliance was unable to find any leak, but each time, the freon was depleted. In addition to the health hazard of having freon leaking into the house, we have had the distinct displeasure of having to deal with food waste, etc. Because of the ongoing problems with this product, we are now facing the reality of purchasing another refrigerator to replace this Whirlpool product.Due to this, I feel it is difficult to consider another Whirlpool product and will question any product to ensure that it is not Whirlpool-related. If there is anything that Whirlpool or Lowes can do at this point, it would be appreciated. Thank you for reviewing this note of dissatisfaction. It appears that we will be shopping for a new refrigerator this weekend unless we hear from Whirlpool. In any event, I would like this recorded as a complaint from a former customer.

We moved into a new home in December. We purchased the home too late to choose our appliances or upgrade over what they install. From the start the oven has been aggravating in both the noise that it emits and the variance in actual temperature. We have had the Appliance Service out twice for these ovens. We are told that the noise which sounds like a wind tunnel is normal. It is there to keep the circuit board cool especially during the cleaning process. The noise is quite aggravating and is amplified throughout our open floor plan to all parts of the house.The temperature variance has been calibrated to be more accurate, but Im not convinced it is on the right temperature yet. I continue to give it a try, but Im not sure if the noise of the fan in the oven is making me feel negative towards using the oven at any time. We hate to have to replace these new units with another set of double ovens, but I doubt if I can continue with this noise much longer. It will definitely not be a Whirlpool or KitchenAid double oven of any sort.

Whirlpool Gold refrigerator WRF989SDAH00. I purchased this French door refrigerator based on past experiences with Whirlpool and sad to say this is not the same quality product I have know Whirlpool for. After the warranty ran out, it died. The first service company I called identified the problem as a known (to Whirlpool) design flaw. They would not touch it and referred me to contact Whirlpool. I did and the company referred me to Dinos Appliance Factory Service (in Phoenix AZ). They came out and confirmed it was a design flaw. They replaced the evaporator and compressor and it lasted about 6 weeks.

We purchased a Whirlpool Cabrio washer and dryer less than 2 years ago. These are supposed to be high efficiency appliances, but the washer has never cleaned the clothes well and the dryer often has to be run more than once in order to get the clothes dry. Then, about two weeks ago, the washer started making such a loud noise on the spin cycle that it sounded like a jet plane taking off. It was hard to hear the television when it was running. Today, it started screeching and water leaked on the floor. I called the number listed on my manual and was basically told that it would cost half of what we had paid for the machine to fix it. What efficiency, a poor machine that lasts less than two years. We will never buy Whirlpool appliances again.

We purchased our Consumer Reports rated #1 best washer, seven yrs. ago with a five-yr warranty. We have had nothing but repair after repair starting in the first year. The mother board replaced twice, the entire inside had been replaced within four years. It is only a household of three, the washer looks like new! The machine is now making a noise like a freight train... We had a repairman out $95.00 just to look at it! Cost of repair $1,116.21!!!! More than what the machine is worth. The replacement parts wore out in the last 2.5 yrs, again poor design. I contacted Whirlpool during the last repair issue and demanded a full replacement. The customer service rep, as RUDE as can be, checked with her higher-ups and said they would replace it for $845.00!!! WHAT A JOKE. I could buy a new one for that! The repair person said they are one of the highest repair units and the most costly out of warranty. He had one with the same issue just two days prior. I will never buy another Whirlpool product or purchase from H&H Gregg. They sold our warranty twice losing all of our repair records! It looks like I had an extra load size dumped on me!

I bought a brand new Whirlpool washer and dryer set -Cabrio- $1700.00 in 2011. It is by far the worst washing machine I have ever purchased, and I am 60 years old!!! It is now three years old and has been repaired at least 4 times. Long story short... after hours & hours on the phone, along with many threats! (By the way I had to ask for a manager two times up the ladder for this to happen as they just kept repeating that it was out of warranty coverage). I also told them that I was going to have one of my company trucks deliver this machine to Sears lot, along with a paid person to inform every shopper of my plight with this washer and the lack of service from Sears and Whirlpool! Whirlpool finally agreed to pay for the parts but not the labor on this most current repair. (This time it is the transmission!! In the past it was the Hub, twice. The gear case twice and the belt a number of times). I am now going back to Sears to request (that might not be the correct word) Demand, that they take care of the service bill for this machine. In between repairs, I have dealt with ongoing cleaning quality problems. This machine does not get clothes clean. I always have to wash them twice. This machine is loud. This machine does not use enough water to even dissolve the soap. So much for energy saving measures when you have to wash twice and still see soap and crud in the tub. Worst, worst, ever washing machine in my life!! By the way, I have an 8 year old Maytag too that I have never had to repair. Moral of the story, buy Maytag, or at least do not buy a Cabrio!!!!

Whirlpool Cabrio Model WTW6500WW1 - Have had good luck with previous Whirlpool Washers so thought I would purchase this one 2 years ago from Menards. Paid more than I normally would and thought it would be worth the extra money. Not so.......As many others, it has a foul odor that will not go away and now sounds like a freight train in the house. Called Whirlpool about this issue and parts are not covered. Total cost of parts including the tool that is needed for this repair is $187.00 not including shipping. Whirlpool has lost my business moving forward as like many others, Im sure. Very disappointed!

We purchased the gold series model WDT790SAYM1 in 2013 replacing a 12 year old Maytag we were very happy with. The Whirlpool just does not clean very well and leaves dishes dirty no matter which cycle you use. The spray arms are cheaply made and do not work well. Its a piece of crap compared to the old Maytag. Do not buy any dishwashers from Whirlpool, they are simply inferior products and a waste of money.

It has been a great refrigerator that has lasted for years without repairs. As of today, it is a bit outdated but still functioning. I hope it doesnt break now that I praised it.

The Whirlpool duet model wfw9150ww01 washing machine is a piece junk. After using it for two years, the bearing has gone out on it and it sounds like a freight train. It will cost $600 to repair it. We only paid $575 for it. What a rip off. Whirlpool makes junk only. Buy something else.

Purchased WRF989SDAM00 French Door refrigerator in 2013, and 33 months later it is not cooling (fridge 45/freezer 36 degrees). Service call diagnosis is a leak in the sealed component area. Since it out of the 1 year warranty period, nothing is covered. This is the first of Whirlpools dual evaporator models, and is technically challenging according to the service technician. Most likely one or both evaporators are defective, and this type of failure comes with a recommendation to change out the compressor as well as it is moisture compromised.As my previous Kitchen Aids had 10 year sealed component warranties, and the Whirlpool is the same base mechanism as the Kitchen Aid, I contacted Whirlpool to see if they would extend my warranty coverage to these sealed components. Website submission - never got an answer. Called the customer service line - they politely told me they were sorry but there is nothing they can offer me. Even the extended service plan would not cover me as this refrigerator has a preexisting problem and it must be 100% operational to begin an extended service contract.Im extremely disappointed in this fridge only lasting 33 months, in comparison to my previous Whirlpool/Kitchen Aid refrigerators. Of course the internet just allows me to see that Im not alone is purchasing a short lived appliance. So here is my contribution to the internet of things: Do not purchase Whirlpool refrigerators expecting them to last much beyond the warranty period. Buyer beware.

My two year old Whirlpool refrigerator died. The compressor went bad. $859 to replace it. I only paid $999 for the fridge. This was crazy. Two years old. Heard it was not uncommon and the technician said most refrigerators warranty the compressor for up to 5 years but not Whirlpool. Had to go buy a new refrigerator.

I purchased a Whirlpool refrigerator from Home Depot in Nov, 2013. Model is WRF560SEYWOO with water in the door and bottom freezer with ice compartment. This is a very small refrigerator for my very small space. I swear these companies program their appliances to break down exactly 1 month after the warranty is up. Thats what happened to me. Dec 2014 this horrible loud humming noise started. You could hear it out on the sidewalk! Then the door with the water just detached from the bottom and screws and plastic pieces fell out all over the floor. The day the repairman came he noticed all the rubber lining in the doors was detaching and huge chunks were falling off of it. He called to get replacement parts for everything and whatyaknow, all parts for this unit have been discontinued!This is what we did to cope with all these defects. The noise was caused by ice building up around the exhaust fan because the unit had stopped defrosting that area, so every 3 days I have to get out my hairdryer and melt the ice at the back of the unit. Next we MacGyvered the door so that it is resting on the freezer door. Next, he brought in some tape and taped all the pieces of rubber falling off my doors!! This frigging frig cost me $1,653.00!! I AM FURIOUS. Why isnt Con. AFFAIRS DOING ANYTHING ABOUT THIS?!

I would not, at this time, even really give this product 1 star, but that was the lowest rating allowable. We purchased a Whirlpool Gold French Door Refrigerator at Lowes a couple of years ago after our Amana was toasted by a close proximity lightning strike. (It got more than just our frig, but the replacement frig is the only item we have had issues with.) We even got the extended warranty thru Lowes for the unit. Shortly after the extended warranty expired we started having issues with the bottom freezer door icing up. We thought that possibly the grandkids had not shut the freezer. So we cleaned up the ice around the door, but the problem persisted.The ice cream in the freezer was rock solid, to get it out of the container you had to put it in the microwave for a couple of minutes. The items in the frig were also frozen. So we emptied the frig and freezer, unplugged the unit and let it sit for a couple of days with the doors all open. We then plugged it back in and hoped for the best. It seemed to be ok for a couple of days then the ice on the freezer door appeared again. At this point, I contacted Whirlpool to see who was a licensed repair company in our area. I contacted the licensed repair service, explained my issue, they got the model and serial number info and ordered what parts could conceivably be the culprits.The tech came, the unit was frozen up, all the vents in the freezer were showing icing. So he removed the back of the freezer compartment and thawed the unit out. At the same time I mentioned that the ice maker had quit working, he found that the wiring connection was not properly connected and fixed that while he had all the stuff out. After re-assembly he ran all the diagnostic tests Whirlpool lists and found everything passed. Since the boxes of parts had not been opened they could all be returned to stock. So no charge for parts, as he could not find indication that any were needed.So 1 service call at $100 and it appeared that maybe the issue was resolved, not the case. Not even a month later, issue re-occurred. No grandkids had been there, no instance of the freezer possibly left ajar. Another service call, and by the time the tech arrived, since I had unplugged the unit and emptied it again, all the frost/ice was melted. $100 for a service call, tests all came back as nothing indicated as not functioning.So if I dont put too much stuff in the freezer or too much stuff in the frig it will run without freezing up for about a month. Oh and weekly put it into the defrost mode a couple of times. Now it has started making a tic-tic-tic or rat-tat-tat sound to the fun and games. If the noise is non-stop, it only stops when you open the freezer door. Leading me to believe it is a fan. (Correct, I was told by the local Whirlpool licensed repair facility.) I have spent the weekend, again thawing out my unit in hopes that the noise will cease. It is loud enough to be heard at the other end of the house.No such luck, so I spent an unproductive 1-1/2 hours on a call to Whirlpool yesterday. The larger part of the time was on hold waiting to talk with someone, anyone. Due to our unusually high call volume, wait-time is long today. Thank you for your patience. To retain your place in line, do not hang up. Finally, I got a rep named Karen, who sounded like she was almost asleep. She had very little to offer except, Im sorry you are experiencing these problems. I have no record of previous complaints like yours on record for this model of our product.Hello, I found 929 reports of the same issue on Consumer Reports. Oh, you cant believe what you read on the internet was her response to that tidbit. She offered to sell me a Repair Plus 1 Plan for only $359.95. A licensed repair service comes, repairs your unit and the plan gives you ONE YEAR of peace of mind. Lets see... I said... so you are offering me an extended one year warranty? Oh, but it comes with a repair first then one-year peace of mind. Seems that Whirlpool has moved into selling warranty extensions rather than fixing the issues with these Whirlpool Gold French Door refrigerators. With what I have already paid for service calls added to this Repair plus 1 Plan, I would have invested $$$ enough to BUY A NEW FRIG that is not a Whirlpool product.Seems a bit foolish to me. So Whirlpool is not admitting that there is a design or manufacturing problem with these units. Even the ones sold just this year seem to have the same issue. They have not corrected this and it appears they have no intent to do anything about it. She did indicate that they had a known issue with the drain and that a fix was offered for that (a redesigned drain unit could be installed). But since I was not getting ice build up on the bottom of my freezer compartment I did not appear to need the redesigned drain unit. Her evaluation of my issue was that the drain did not appear to be a problem.So after a fruitless call to Whirlpool, oh and they did have my previous emails concerning my issues on file but did not consider my complaints to be part of a known issue, I have the local tech coming back to see if possibly there is something, anything to be done with this refrigerator. So another $100 at least, likely no resolution if the service tests all come up normal again! So when the tech comes, I am going to ask him to contact the service engineer that he is supposed to have the contact info for (per Karen at Whirlpool) and see if he can get any resolution to my issues by using that service engineer.

I bought my fridge in late 2008 and I am already experiencing potentially expensive repairs due to what I believe is a defective design system, of which, consumers are having to bare the consequences for those who collected our hard-earned cash and delivered a lousy product! I saw so many similar complaints about the ice system on this fridge that I am almost positive that it qualifies for a class action suit and settlement. How about a collaborative approach to this since we have all suffered needlessly? Tell me what you think and if you are in on it.

I purchased a 30 gallon gas hot water heater from Lowes in 2013. Within the first 3 months, it went out. I contacted whirlpool who troubleshot the heater 4 different times. Final contact was in early 2014, I requested a tech to look at the heater. Was informed it is now over a year old, it would be at my cost. Replacement parts $30. Shipping the water heater is great if you like cold showers. After a little searching, I find they know this water heater is junk as does Lowes but dont care.

This product is unsafe and should be recalled. It has aluminium wires that connect the unit to the 220 Vol Power source. Aluminium and copper wire dont mix. I took a shower and was getting ready to leave for the day when I went into my garage to smell burning plastic and wires. I traced it to the hot water heater and discovered the wires in the Energy Smart were melted and burned. I checked with Two Electricians who told me that the wires in the unit can not handle the high heat and melt. If you have one get rid of it. Had I left for the day I would have lost my home, cars and pets. If anyone would like to see this unit I still have it and photos.

Error f1e2 error. Washer less than 2 years old.

We purchased a Whirlpool Estate Range in 2008, with an extended warranty. We have only moved this range out 2 times since it was installed and the last time was over 2 years ago. This range worked beautifully, no issues whatsoever. Until... tonight, the oven & one burner were being used when suddenly the range started arcing, which blew a hole through the back panel on the stove where the cord hooks to it. It continued to arc and quickly fill the kitchen with black smoke until we could reach the breaker box. The Whirlpool repairman wants to charge $88 dollars just to tell us WHY it happened. After 2 years of sitting in the same spot, why? I dont want the stove repaired, I want it out of my house! I will not take the chance that this will happen again when we are not home. When asked if this was an issue with their product, the repairman answered, I have never heard of anything like this before. After reading these reviews: Such a Liar! I wouldnt believe anything Whirlpool, or their representatives told me about their products now. I just want their crap out of my house and I will never spend another one of my hard-earned dollars with them again. Too many other choices out there. I just want other buyers to Beware of Whirlpool.

Our Whirlpool Duet front loader washer developed a mildew smell and started making a horrible banging noise on the spin cycle. We had a service man come out and the concrete weight had broken in half. He said this was not uncommon. I just did a Google search and apparently this is a true factory defect. Luckily we had purchased an extended warranty. I always thought Whirlpool was a premium brand but after this experience I will never buy another washer from them. They should do a product recall.

The electronic panel on my 4 year old barely used wall oven went out when I used the self cleaning function for the first time. It is going to cost $400 to fix it and another $100 to replace the stainless steel sides. They will have to remove to get the oven out of the wall. The oven door is locked and cant be opened so of the wall will have to torn out as well. I called Whirlpool 3 times and have offered no assistance.

We spent a lot of time researching to make sure we were making the right choice, found the one that was right for us. When it got delivered there was a problem though, the plastic scratch protector film they put on the doors for delivery left an adhesive residue that looked like dull spots all over our new shiny black doors. I immediately opened up the owners manual to see how they recommend removing this blotchy sticky residue, assuming we werent the first ones to ever come across this problem, unfortunately they only provide generic cleaning tips. So I went to their website and found what I was looking for. I tried all of the cleaning methods they provide, none of them even came close to working. So I grabbed some adhesive remover and tried that, it worked great to remove the residue however my microfiber cloth (which they recommend explicitly) started leaving scratches all over the finish.I called the customer service to see about getting a new door delivered, thinking this wont be more than a 5 minute phone call since I had followed all of their steps they provide both in the owners manual and on their website. Heres where I find out that their policy DOES NOT cover scratches/cosmetic damage, period. I tried reasoning with them, I had them read their own recommended cleaning procedures, and we both concluded that I had followed their procedures to the T! You might think that if the all of the typical procedures didnt resolve the issue, that would be the point where the customer service reps would have the ability to make a decision that satisfy the customer, you would be wrong! They kept telling me over and over that their policy doesnt cover cosmetic, therefore there was nothing they could do. It was delivered with a defect of sorts, how is the customer responsible for that? The only way I can see it having worked out in my favor is if I had never tried to clean it myself and immediately called customer service, I still fear they would have given me the same line of cosmetic damages are not covered even if I would have tried each procedure with them walking me thru it over the phone. Lesson learned, I will never purchase another Whirlpool product!

I like this refrigerator. Its a two door. I did not get an icemaker and I have plenty of freezer room. The milk will stay fresh at least for a month. I like the crispers. They keep my food fresh. It keeped the Romain lettuce very fresh on the package, it was pick 7/31/2019 and just have a fresh green Salad Sept 6, 2019. Easy to move when wanting to clean the floor.

After one of the door shelves in our new refrigerator cracked, I ordered a new shelf from our local agent Neuman Appliance repair in Ashmore, in July of this year (2014). I was told that it would take a while as Whirlpool were notorious for poor service; however, it is now the middle of September, and we are still waiting!When we ordered a new part for our dishwasher from Fisher and Paykel, we received the part in just 3 days. I mention this to give an idea of what good service should be.

This Whirlpool Water heater was purchased through Lowes on March 29, 2011. This past weekend, water started leaking out of the thermostat/natural gas control located on the side of the tank. I called a plumber to take a look. He stated that a new thermostat/natural gas control was needed. Although the tank has a 12 year warranty, this item does not. Whirlpool did agree to replace the part but would charge me $30 to overnight the item which still would have taken 4 days because of a weekend. To install the item would have cost me almost $500.00.To purchase a new Rheem Water heater was $999. I chose the second choice as the first choice would have still left me with a subpar water heater obviously already out of warranty. The reason for my review is that I saw the number of complaints on the failure of this part. When I purchased this water heater, it was the better model due to the 12 year tank warranty. What use is the tank warranty when the other items dont last? There should be some type of reimbursement but Im not holding my breath. Please buy a contractor grade water heater and not the cheaper models.

Bought Whirlpool Gold refrigerator, microwave, and stove. The bottom where the freezer is located leaks if you dont slam the drawer shut - many times leaking regardless. The microwave needs to be unplugged/reset about once a month or so because the power dies - light comes on, food rotates, no heat. And the small stove light indicating the burner is on for the front left burner suddenly doesnt light up. 0 for 3 on satisfaction. Appliances are 2-3 years old. Did not get extended warranty. Everyone tries to get you to buy but didnt realize I was buying junk. Will not recommend or buy this brand again.

We purchased our new Whirlpool Cabrio washer on November 1, 2013. From the start this machines performance has been a disappointment. We bought the machine at The Brick (I should have known better) where we had made several purchases over the years ( I guess Im a slow learner). Right off the hop, my wife and I noticed that the clothes were not coming out clean. Even though the machine is Eco and therefore advertises that it uses less water, there should be enough water that the clothes at least get evenly wet. That may be a problem with the agitator not seeming to have the guts required to pull the clothing down to the bottom of the drum. We went back to The Brick and told them that we were not happy with the machine they had sold us and quite predictably they told us that we should call Whirlpool (This was less than a week after we had it delivered. Did I mention that I may be a slow learner?). We called Whirlpool and they told us they would have a tech out to take a look at it on November 11th. Wow, I thought. Hows that for service. A repair guy coming out on a statutory holiday. Of course it didnt happen. When we called them back to ask if their repair guy had made it home okay, they claimed that we werent there when the repairman tried to call to confirm his arrival time at our home. We hadnt left the nest the entire day. They then told us to go back to The Brick. We went back once again and told them, yet again, that we were not satisfied. This time they agreed to send their own man over to take a look. He came over yesterday and watched the machine go through an entire wash cycle and then said that there really wasnt anything he could do, as even though it may do a crappy job of washing the clothes, it at least appeared that mechanically speaking there didnt seem to be anything wrong with it. We called Whirlpool back today and they said that there isnt anything wrong with it mechanically so from their end, at least, the story is over. What kind of customer service is that????? Maybe Whirlpool and The Brick deserve each other, but I think we should get better treatment than that

I am writing this complaint because of the very poor service of Whirlpool. My washing machine broke after 1 year of use. Luckily, I was on my 2-year insurance. The wiring fully collapsed and I needed to change the whole drum. I called Whirlpools customer service and they said that they would fix the problem after 2 weeks. They came on the day and found out the problem and ordered a new drum. They said they would fix it up on the 5th of December, and it has already been over 3 weeks. On the 4th of December, Whirlpool called me and said that the item they had ordered for me has been damaged. I am not satisfied by these products because it is only a drum (it cant break that easily). I cannot recommend this company to my friends and family due to the quality of the products and the poor customer service as I was waiting on the phone for almost an hour trying to get through.

Refrigerator stopped cooling... Paid $200 to have it diagnosed... Cost more than a new refrigerator to get fixed...$14,000. Refrigerator was 7 years old, energy star. How can it be energy efficient if it was made to last only seven years? How much energy is wasted making new ones to replace the broken ones, that cost too much to fix. Energy star. What a scam.

I purchased a Whirlpool Washing Machine in November, 2015 and today, I had a repair person out who said the bearing had ruptured and the washing machine cannot be repaired - 2 1/2 years later. Contacted Whirlpool Customer Service who would do nothing other than try to explain to me that I should have purchased an extended warranty as they could not stand behind the machine past the one year. Would not even offer sending a tech out on their dime to confirm what my repairman had said that this is a failed production process of these machines - it was nothing that I had done caused this issue. But yet they wanted to sell me another machine. It will be a cold day before I purchase another Whirlpool product.I was shocked at the lack of customer service to assist with a situation that both the location I purchased it from and my own repair tech said that they are seeing so often with these machines. I would never purchase another item from Whirlpool again nor would I recommend any of their items. I will go to great lengths to give others the background on how Whirlpool will not stand behind their products, lack of customer service to resolve a situation or can work outside of what is given to them to correct a situation - this is not OK!

The washing machine continued to display an F1 error code. I contacted the manufacturer and was told that they will not do anything about the problem due to it being out of warranty. This is the first time I have complained about a product or service and want to try and assist anyone who may be thinking of purchasing a washer from Whirlpool. I do not recommend purchase of these units.

This machine was my dream machine for about two years. Then the noise started during the spin cycle. It gradually got louder and louder, until it got so loud that it sounded like a jet engine taking off. You could not be near the wash room and hear each other talk. Then it began to aggravate me with the UL flashing. I know how to load a washing machine. It was just a defect. Then it started making a grinding sound to add to the roaring spin noise. We were told that it would take over $500.00 to fix, so we just sat back and waited for it to die. Well, the other day it began to leak some water out of the bottom of the machine. Now today we are paying our last respects to a piece of junk that Whirlpool calls a washing machine! It is less than 5 years old. This was a $900.00 washer. There should be a recall. We should ban together and demand a recall! Now I will be forced to go buy a new washer. I can tell you which name brand I will not buy, Whirlpool!

We purchased a new motor home with a whirlpool refrigerator. The refrigerator went out three months after purchasing this new motor home. We have had two expertise come out and check. Both repairmen said there was a leak in the cabinet and needed to be replaced. They called Whirlpool who will not honor the warranty. We are still under warranty but it is not worth the paper it is written on. Do not buy their products because their products do not work and they will not replace broken items from the manufacture. Will have to contact better business. Not material enough to hire attorney. This is what they count on. BEWARE.

I purchased a Whirlpool Gold refrigerator in May 2012 and about 8 months ago, ice started to form in the freezer. The ice melts and water drains out, so when you come in the kitchen all of the sudden you step in a puddle of water. I called CS and they told me the best they could do was authorize part(s) and the labor and service call would be my responsibility. Everyone knows service cost way more than parts.

We bought a Whirlpool washing machine, and what a mistake! I just got off the phone with their customer we dont care department. It spins everything into a tight ball so when the clothes come out of the washing machine everything needs ironed, even permanent press. It also changes the water temperature. I like to wash some clothes in cold water, but the representative at Whirlpool told me it will sometimes add hot water to make the water warm. I am hoping this review will save others from purchasing a Whirlpool washing machine. We will stay clear of all of Whirlpool appliances due to the problem with this washer and Whirlpools lack of concern of an inferior product!

Always buy an extended warranty if you are going to buy a washing machine. Mine cost $129.00 extra and it is not through Whirlpool. Three control panels and two tub bearings later, the extended warranty insurance carrier gave us our money back to buy another machine. My wife loves the operation of the Cabrio, so we bought a WTW8200YW today, in the false hope that it will work much better. We have an extra washing machine in the garage for the three week period before repairs. The serviceman has to come look to verify the problem, then come back when the part arrives.

I purchased a brand new fridge in July of 2014 (model wrf990slam00) hoping refrigeration repairs were now behind me. They were not. The ice machine did not work from day one and they knew it was defective when I called so they had someone come out to replace it. Just over a year later it is not working again and my freezer will not freeze either. They tell me I am now out of warranty and any repairs going forward will be out of pocket. Congratulations Whirlpool. You make products that last a whole year. Do not buy Whirlpool. They could care less about you or the quality of their products.

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

This is a defect due to the removal of the dispenser heater being removed. The insulation is inadequate behind the ice/water dispenser (@ 3 feet from the bottom of the door.) Replaced the line, thawed it out multiple times, added extra line under the fridge in the coils to try and warm up the water in the line between the 90 degree elbow connector and the dispenser... no luck. Since all the manufacturers models are being assembled in Mexico, using the same designs, other models are have the same issue. GE is backing theirs with a replacement freezer door. Well see if Whirlpool backs theirs. This whirlpool Gold is @ 3 years old and the issue started around a year ago.

Clothes come out of washer are soaking wet. Despite multiple repairs within the warranty period (1 year), the problem was not fixed. Each time a separate part was replaced. I would consider this as a manufacturer defective product. Despite multiple complaints to Whirlpool customer service, they would not replace the unit. Problem continues and now the warranty period is over and I am paying for fixing the same problem. I would not buy a WP washer again.

I am 72 years old and this Whirlpool Energy Star HE Washing Machine is just useless. It does not clean clothes properly. It always leaves a stinky washing machine smell which never goes away despite no matter what you do. A completely useless, faulty washing machine! Never ever buy a Whirlpool HE washing machine! Some websites say that you need to buy a washer fan at a cost of $69.99 and attach it to the back of your washing machine as this is the only way you can get rid of the smell. Who has that kind of money? Why is this fan not already included in this washing machine if Whirlpool is aware of the smelly washing machine/smelly clothes problem? This is such a joke! We would like to be reimbursed for our deficient Whirlpool Washing Machine or at the very least, have a recall of this inefficient, poorly designed washing machine. Report them to the Better Business Bureau and anyone else you think can resolve this problem - thanks!! - Unhappy camper

It took 5 deliveries to get a fridge that wasnt damaged. First two came from Leons - the same damage on both. Then they said we had to go through Whirlpool because so much time had lapsed. We had purchased the full set of Whirlpool Gold for our kitchen renovation; therefore, we were unable to unpack the fridge until the cabinets were completed. I phoned Whirlpool Canada, and they said they had to send a service tech. The service tech came, and he confirmed the damage and was told to patch it with a proxy. Sorry but I had just paid $1500 for a new fridge. I didnt want a dent and damage. We received no offer for discount to accept the damaged fridge. They sent another one, still damaged. They used their truck to deliver and the guy had no idea how smashed our brand-new trim.So Whirlpool sent another fridge, and even though I asked them to check it before sending, they didnt. It was damaged. This is four fridges. Im tired of fighting with Whirlpool. I called Leons, and they take care to get me a new fridge undamaged. I told Whirlpool about the damage, and they sent a form. First, they wanted me to claim on my house insurance. Why should I put on a claim? If not, get two quotes and fill out tons of paperwork. Im just too tired after fighting for over two months to get a fridge that isnt damaged. Not even an offer of compensation to cover all the time taken off work and the stress on me and my family. This is the second set of Whirlpool Gold we have purchased in the last 4 years. I doubt I will ever purchase again, because you are a company that doesnt treat your customers with respect or concern.

My wife and I purchased the Whirlpool calypso washer and dryers and have been regretting ever purchasing a Whirlpool product. Not more than a year and a half after spending thousands of dollars on their products the troubles started. I called the company and they sent someone out to look at it for repair. He vacuumed out the lines and kept restarting it over and over and eventually it started working again and they charged a hundred dollars and something and said there most likely be more problems since they have many calls on this issue. Sure enough it started again and just kept retrying it over and over to get it to work again as well as vacuumed the lines again like he did. Now its at the point it will not work no matter what. It just keeps flashing LD and shuts down. So I did a online search for other consumers having the same problem and was shocked by the amount of the same problem with others (search this model flashing LD and you will see for yourself). When I contacted Whirlpool they played dumb and lied right thru their teeth saying they have no issues with this model and refused to do anything. I have since learned there has been court cases where the courts ruled against them saying that it was defective and had to notify consumers which they never did. Even when the repairman came out nothing was said. I have since learned that all they did was changed the name to a different model which is having the same problem (no kidding!!) and continued to rip the public off in the name of CORPORATE Greed!!!!! I advise everybody never to purchase a Whirlpool product ever again and maybe we can bankrupt them and put them out of business where they belong. All the customer service agents deserve to be unemployed and suffering after long waits on the phone and then lying straight face to the consumers. Pure evil!!!! We all have to stick together and bring these criminals down. How can they say we have no issues when a simple search of Whirlpool Calypso problems with draining and flashing LD and shutting down. There are thousands of people complaining and no action is done. Shame on these people and their souls are lost forever. Never buy a Whirlpool product and tell everybody you know to stay away! They should have their ** and/or ** cut off and have to suffer the same way the struggling consumers are after scrounging up thousands of dollars for a 200-pound metal paper weight that aint worth a damn!!!!

We purchased a Whirlpool Range from Brands Mart USA and did not try to use it for quite some time because our house was not ready to move in. When we tried to turn on the oven it would not come on. We called a repair service and was told the Motherboard was not working. We realize the warranty was out on the stove but it never worked and the stove is Brand New. We called Whirlpool and they was going to repair and changed their mind on December 18, 2014 at 8:54 am. Before that call we had spent quite a lot of hours on the phone with Whirlpool and Brands Mart USA.. We purchased three appliances from Brands Mart USA Range, Dishwasher and Microwave at the same time they were all Whirlpool products. What happened to Good Customer Service and Return Customers for Job Security? Well neither Company care for their customers. We did not break a motherboard for a stove oven because the range was never turned on because it was broken when purchased.. We are unable to get any help from either company. I talked today to ** & Supervisor ** from-Whirlpool and ** - Brands Mart USA, again no help. Why transfer you from one company to another for 1 hour and 45 minutes? WISH I COULD GET SOME HELP. And we wonder why companies go out of business - word of mouth complaints and especially with Senior Citizens like us.

In April of 2009, I bought a Whirlpool over the range microwave, model # MH2175XSB-5. In September 2011, a small piece of the door fell off at the hinge. Pieces have continuously fallen off and now the door is splitting, rendering the item useless. It was purchased at Lowes and I had them installed the item. Two years of service plus installation come to big bucks for a piece of trash.

I purchased a Whirlpool Cabrio set 3 years ago based on their brand reputation and consumer reports. It has been a terrible experience since the moment the warranty expired. First, about 1 month after warranty expired, I had to replace the main electrical board. Then about 3 weeks ago, the drain pump failed. I purchased the $110 pump and installed it myself. Now this week, the spin cycle sounded like a jet engine. I took it apart to find that the bearings were shot on the drive shaft. I figured, well it is just a wear item, understandable right? So I went to order parts and got told that I have to order the whole outer tub for $250 with shipping! For some bearings! I called Whirlpool directly and was given no explanation other than Call some parts distributors. They may be able to help you get the bearing separate, but we dont do that and there is nothing that we can do. Amazing. I equate that to having a faulty brake on my car and being told that I have to replace the whole axle!Fortunately, the washer never really did a great job. It was loud and tore clothes up, so the decision to part ways was not too difficult. I have the list of brands they make and will be sure to never buy another. Im selling this one for parts. Im sure there are others out there that will need a pump and control board soon!

Cabrio washer broken lid, asked WP to fix warranty. They offered $250 off $500 Amana washer. Said just send me the new lid that would cost me $210. They said no. Asked if they would send me metal lid with hinges less than $100 they said no. Told them I was not going to spend more money with WP, my turn to say no. If you are wise dont buy WP products...

I purchased a dishwasher from Menards. It was a top of the line Whirlpool Dishwasher. We ordered new cabinets for a kitchen upgrade and when the cabinets arrived they were damaged during Thanksgiving holiday. We purchased the dishwasher and it sat in our garage until the second set of cabinets arrived in mid January.Once the GC installed the new cabinets we noticed a small dent in the front of the stainless steel dishwasher. I notified Whirlpool and they took my model and serial number. The supervisor April said there is nothing that I can do. You passed the 30 day cosmetic warranty. I explained the issue to her and she didnt seem to care.The dishwasher sat in the garage for 7-8 weeks. This is not the consumers fault. This company could of sent a service mechanic out and replaced the front panel. But she chose to ready some meaningless policy to me. I will never buy a Whirlpool product again, and I will tell everyone about the poor and unprofessional service that Whirlpool offers.

I had to turn the gas off my water heater and when I tried to turn it back on, it refused. I called the number on the heater and somebody answered. The guy told me to take the pilot gas hose off to make sure there was gas in the line. I did this but after spending 1/2 hour putting the pipe back in, the pilot light did not go on. I called them back and they told me to push a white switch and hold it down for 10 seconds and retry. That didnt work either so they told me to call a repair man and gave me the phone number of a local plumber. Trying not to give up, I removed the pilot light pipe off and tried blowing and sucking on it. I couldnt get air through the pipe so I figure that somehow it was clogged. I tried taking the whole assembly off (there are 2 screws to remove) but couldnt get that out. I called Whirlpool again and asked for a manual to be sent over the internet but I couldnt open that either. The water heater is only 3 years old and already Ill be paying to repair it.

I got my water heater 3/13/12. Ive had to restart it now 4 times & have been totally out of hot water for two months! How can I get help from you or Lowes? This thing is supposed to work for 6 years & I havent been able to keep it going for 6 months! Help please! Can I get a different one? This one hates me! Being widowed & having a metal hip, it’s hard to get safely into the attic to restart it and not sure it will work longer than 2 or 3 weeks! Ive been bathing in the kitchen because thats where the stove is! Thats the only way I have of having hot water, is on the stove! Thanks for listening!

Cabrio top loading washer - I have had this set for 3 years. The first 8 months it was fine, then came all the rust. I had to go to the BBB and file a complaint as everyone at Whirlpool would not help. Last year they finally replaced the top, and now, its rust yet again. I rinse and dry the machine when I am done using it. The repair man said it was because manufacturers are not using primer and just one coat of cheap paint. What now? Ill see if I can get the lid off and sand it and use rust preventer on it. Never again, I should just junk this piece of crap and Whirlpool should shut down if they cant make anything worth our hard earned money.

My husband purchased a Cabrio washer and dryer pair for Christmas 2010. I have faithfully used the affresh every month, and spent a fortune on it I might add. But for about the last year or so, no matter that the washer has been cleaned at times when the load is finished there is all kinds of black stuff in the tub and on the clothes. The tray under the detergent dispenser is all black and nasty and impossible to clean thoroughly. The black stuff will come through the holes in the tub as well. Water stands in the bleach dispenser at times, fabric softener does not all dispense, the LID is broken and has been but I cannot afford over 200.00 for a LID and about 100.00 to have repairman to put it on. We do not have heavily soiled clothes that would create excessive dirt, never have had and we are now retired so we surely dont now. Bottom line, I thought maybe this would be the last washer I would need but I hate it. It is only 5 years old but I am stuck as I cannot afford a new one now. Factory rep says if it is cleaned as it should be, I should not be having this problem. Not true, it has been cleaned as recommended!!!

In July 2018 I purchased a coin operated commercial front load 27 in washer and dryer. It was placed in and used in a six unit apartment building occupied by 8 long term adults. Prior washers and dryers had been operational for years with minor repairs at times. In June of 2019 the interior cement center balance on the top of the washer drum broke with resulting damage to screws securing the center balance and potentially other unknown parts. This was reported to Whirlpool customer Care service and they referred me to one of their a repair services. The repair service in about early August repaired the washer.In late September 2019 the cement balance broke a second time and this was again reported to Whirlpool service who requested I notify their recommended repair service. On inspecting the washer the repair service stated the entire washer was required to be rebuilt. The labor for installation of would cost me $1,125 with Whirlpool providing the parts under their warranty. The $1,125 labor cost was just under what I paid for a new coin operated front load washer. I reported this to Whirlpool whose supervising staff, without any inspection of damaged washer as to determine whether the washer was fit for its purpose when sold as a commercial washer, rejected any replacement of the less one year old washer and insisted they would only pay for the parts and I would have to pay for the labor, particularly when the both the cost of the replacement parts and the labor would be substantially in excess of a new machine. Due to time and effort constraints the problem was resolved by simply dumping the defective washer and purchasing a new commercial front load washer from a more responsible company.

Ive always had a Whirlpool washing machine and it has been extremely dependable. I have not had any problems with my Whirlpool washer. A Whirlpool has came a long ways with their pricing. It was very affordable for somebody like me and I cant afford a lot but I could afford this. I was very pleased with my purchase and with the product. They havent let me down so far.