I am on my second Whirlpool hot water heater within 7 years and both had a 9-year supposed warranty. Upon replacing the pop-off valve (at my expense), I paid $98 to replace the gas valve (part was issued by Whirlpool). Still having problems with pop valve and now the pilot light wont stay lit. Upon calling the number (877 817-6750) I was finally told they would replace the heater. When I stated that I did not want another faulty Whirlpool heater and that I would take the faulty heater back to place of purchase but that I wanted a local plumber to install their own heater, I was told that I had to have a thermal expansion tank or they basically would not do anything. Why would I want a third Whirlpool product? The second one is ruining my tiled basement floor as it is. So after spending over $600 for the faulty heater, now I have to spend $700 to replace it.

Like many other reviews Ive read here this morning, I bought a Whirlpool Cabrio HE Top loading washer before I did my homework. I purchased approximately 2 years ago. While I dont seem to have the volume of complaints Ive read from others, I do have many intermittent complaints. As others have described, from day one I have gone from this uneasy feeling about how it is working to down right POd about the condition of my clothes after a load finishes.List of issues you will avoid by buying a different product: 1. Water levels SO low your clothes dont get clean. Yes Whirlpool, thank you for trying to save me $$ by lowering my water bill, but for goodness sake there should be enough water in the damn tub to cover the load. I literally watch dry clothing twist back and forth and NEVER go out (like they claim) to the edge of the tub and under then back up in the center. Instead they just sit there watching from the edge while the poor items of clothing in the center get twisted together.2. Powdered detergent, even if listed as HE will not dissolve in this low water level and will end up as white patches of film on your dark clothes. Suggestion to avoid this - dont use powdered detergent, but even if you use liquid HE detergent, you may still experience white patches of soap film on your clothes. It happens on all of them but shows up clearly on dark clothes. Setting the washer to always do a 2nd rinse cycle will improve the outcome. Not a perfect solution since the point of a low water washer is to use LESS water and not more by running a 2nd rinse on all your loads.3. No Consumer/User options to allow you to use the washer as you see fit. Since I paid a small fortune for this stupid washer and didnt realize that I would never again be able to dye fabric in my washer I am posting this as a warning to other crafty consumers. DONT BUY THIS WASHER if you ever want to dye fabric or an article of clothing larger than underwear. There is absolutely no setting on the washer cycles that will fill the tub with more than a few inches of water. The washer falsely has a mislabeled setting called Deep Water Soak. This is absolutely a LIE. Good thing I tested the cycle before putting my blanket in there to dye it. The cycle spins many times in the beginning pouring water into the clothes, then empties the tub and does it again. Then after 10 minutes into the cycle it begins to fill (if you want to call it that) the tub.After putting about 3 inches of water in the tub - not even enough to cover the top of the articles in the tub (I used 6 towels as my test subjects) it stops to soak. But stuff is still sticking up out of the water!!! OMG! So frustrating. This would not do for dyeing anything of value as you would not be able to agitate enough to ensure coverage of the fabric evenly with dye. Just dont buy this washer if you have, as I have in the past, enjoyed changing the color of linens and re-dyeing dark clothing that have faded! Whirlpool clearly didnt care about how consumers actually need to use the washer. I may try using this setting by pausing and filling it manually with buckets of hot water from my sink to get enough water in there to cover the fabric. Its just ridiculous that I even have to consider how to outsmart my washer!4. Smelly clothes. Seriously. I do the obligatory monthly Affresh cleanings, and I have learned to leave the lid open after the last load of clothes so the tub can air dry. However, I still from time to time pull a load out of the tub and it smells like mildew. And dont think for one second that the smell will go away when dried. I have opened the dryer and pulled clothes out, smelled the mildew and put them right back in the washer for a 2nd go round. Nothing worse than putting on a clean nightgown and smelling like mildew! Ewe!! With this awful washer you can NEVER leave a load of washed clothing sit for any length of time or you can look forward to smelly clothing. Hate it. Absolutely HATE it. Again, this defeats the purpose of using less water.Cant make myself spend more dollars that I dont have in the budget to replace this piece of crap. I have figured out all the workarounds for now, but as soon as I can replace it I will send it to the dump. Not going to resell or donate to anyone else as it would just be a burden for others. If there was ever a rightful need for a class action lawsuit to compensate consumers for false claims by a company - this is it! Hope this helps prevent anyone reading from making the poor purchase decision I have!

I purchased a Whirlpool cook ceramic cook top for our new kitchen. The very first time I made something (it was lentil soup) something stuck to the cook top. I have had a ceramic cook top before for 18 years - never had a problem until the whirlpool cook top. I cannot get it clean. I have tried everything! Such as stove top cleaner designed for whirlpool cook tops ($22), other cook top cleaners, the single edged razor, a scrubby sponge, steel wool, I even resorted to furniture stripper - NOTHING has removed this spot. I am ready to throw out this new stove top! What a huge disappointment this Whirlpool product is.

I hate my Whirlpool refrigerator: It has a upper freezer with no light. The shelves are not split and raising or lowering shelves gains nothing and may even take space away. I would never ever buy another Whirlpool.

We purchased the Cabrio Whirlpool washer from ABC Warehouse October 18, 2014. They said if we purchased a washer of higher quality it would last longer. We have bought Whirlpool washers for over 40 years. When our last one only lasted for three years they convinced us to spend more money over 1000.00 witha purchase of a 5 year warranty 6 days over the warranty. It is junk. The bearing went out costing 600.00. They graciously offered to sell me another washer. WOW, everyone is sorry that we have this problem BUT you are out of luck. Are they kidding? I will never buy another Whirlpool. They use to be the top of the line but now I feel we are in a throw away world and talk about consumer rip off. FLEECING OF AMERICA AT WORK!!!!

We have owned Whirlpool Oven/Range for 3 years, and about 4 times a year, on oven setting over 400 degrees, we get an error message, beeping, and the oven needs to be reset. We also own other Whirpool appliances, and caveat emptor. Buy another brand, please.

We bought the Cabrio washer and dryer on June 2008, and it wasnt very long after that, that we had to have a repair done. Then, it started twisting the clothes and the sheets into a big knot. Two king size sheets and 2 pillow cases got so twisted that they are no bigger than a watermelon, and believe me, they are very hard to untangle when they are soaking wet. The machine in the drying cycle sounds like a commercial jet taking off. We can hardly talk above the roar of that thing. I hate it with a passion. Whirlpool used to be all we bought, but that is going to change.Linda

We bought a new Whirlpool side by side, model # WRS325FNAM00 in March 2014. In less than 48 hours, the freezer box was condensing and water was leaking on the bottom edge. The condensation got worse and worse. Five service calls later, Whirlpool replaced the freezer door--which took six weeks because it had to be manufactured.After the door was installed--no change. Whirlpool replaced the entire refrigerator in June. Guess what? The new one is doing exactly the same thing in exactly the same place. So far it has not gotten worse. Well see, we have only had it a week. But already the service rep has been out to the house and added the silicone gunk to the box in case there is a tiny air leak. Why would a brand new refrigerator have an air leak in the freezer box?

Once again I am disappointed in a product that I felt was of the utmost quality. However after buying in 2010 and not being installed until 2011, the over the oven microwave has a crack on the outside of the door. Two pieces have fallen off from under the plastic rim on the inside of the door, two pieces of the door one on the top right side and the other on the bottom right side have fallen off. All I have to say is the two Whirlpool products I bought at Lowes has been a huge disappointment especially since the other two bought from the same stores are Frigidaires and work beautifully...

Have had Refrigerator less than two years and the evaporator seal is leaking and all the Freon is gone causing the freezer and ice maker to quit. Will cost $700 to repair. Found out it is a known defect with Whirlpool. Called Whirlpool for reimbursement and they refused, saying they do not know anything about this issue. This is interesting since it is all over the Web with complaints. I have been a customer of Whirlpool for 20 years and they have lost me and everyone else I know.

Purchased this washer in 2009 from Lowes, believing the hype that it was efficient. Since we only needed a Washer at the time, we overpaid (it is more cost effective when you buy both washer and dryer). So we paid $1000.00 for this machine (we purchased the stand as well). After the 1st year, there seemed to be a significant decrease in how fast the washer spun, as the clothes were coming out wetter. I didnt pay much attention, but 2 years later, the machine has a weird problem where it couldnt complete the cycle, and by this time, every time it Spun, the noise was louder and louder.I contact Whirlpool, placed a service call and the Technician came out. $225.00 later, there was a hose that was pinched that was sending a wrong signal to the washer. He fixed that and told me I should get a contract on the machine through Whirlpool since I seemed to be having problems. I purchased the contract, for $300.00, and 2 1/2 weeks later placed another service call, as the noise from the machine was happening every time I did laundry. The service guy came out, indicated that it seemed to be the Agitator, and that he would need to order parts, and that they had a SPECIALIST who only does this type of repair, since they have many! He also indicated that the hose may have crimped due to the movement of the entire agitator!Well, after not hearing from ANYONE for 2 weeks, I called the repair company who told me WHIRLPOOL was supposed to call and let me know that they would NOT fix the machine, as the parts cost more than the Washer, which is now valued at $500.00! No one from WHIRLPOOL EVER CALLED, and I cant understand how a $1000.00 Washing machine touted to be so efficient and environmentally friendly has been THROWN OUT after 3 years!!! And now I am out the $225.00 repair, have no washing machine, $1000.00 down the drain (and I forgot to mention a year later we bought the matching WHIRLPOOL DRYER and OVERPAID) and now have to purchase another machine, which I assure you WONT BE WHIRLPOOL! As most of us have experienced, WASHING MACHINES last for many years! The washer I had before this was over 20 years!!!! So much for efficient and environmentally friendly... The only thing GREEN about this machine is how much of my $$$ has gone to Whirlpool!

I have a rental home and my residence, I have purchased a fridge for BOTH places. Within 1.5 years, both of the fridges shelving cracked. Customer service will not do anything to remedy this. It is a known issue with his model of appliance. There are numerous complaints and they DO NOT stand behind heir product. NEVER BUY WHIRLPOOL.

This range is easy to clean, easy to use, multi functional burners, easy to use oven and very nice looking. We use propane instead of natural gas and the conversion was quick and efficient. We absolutely love the griddle.

Purchased Whirlpool gas hot water heater from LOWES on 9/25/2016. After the installation, tried to light the pilot light for 90 minutes. Followed the recommended instructions, I could not get it to light. Called LOWES they told me to call Whirlpool. I did so, and told them I will return the heater to LOWES the next day. Whirlpool customer service very bad. Returned the heater to LOWES the next morning, went to a local plumbing shop and purchased a Rheem heater. After installation it lit very first attempt. Now three weeks later I get a letter in mail from collection agency that LOWES turned me in for stopping payment on the check I wrote them. After reading the many negative reviews and they disregard for my and my familys safety, nobody should purchase a Whirlpool gas heater from LOWES.

Purchased the Whirlpool Cabrio supposedly a top of the line washing machine? Not even three years old, used 3 times a week for normal to small loads, for a family of three. Stopped spinning water out, so clothes are soaking wet at the end of the cycle. Repairman said I need a new transmission and inner spin basket is completely worn. New parts will cost me around $500!!!! Repairman said this should not be this worn down in 2 1/2 years. I purchased this machine to replace a Roper brand machine I purchased used for $200 and had for over 10 years without issue! I will NEVER buy Whirlpool again. They do not stand behind their product! I should not have had any issues with this machine for at least 10 years!

We bought this refrigerator (Whirlpool Model # WRF9913F1FM00) last August 2016. From day 1, the water coming out from the water dispenser was not cold at all. Same temperature as the tap water. By November, the refrigerator started to get warm. Apparently, the evaporator fan motor had to be changed according to the technician who spent more than an hour on the phone with their technical advisor to diagnose the problem with the refrigerator. After a week, the refrigerator got fixed. Not only did the refrigerator started working again, even the water from the dispenser got finally cold, too. Now four months later, March 2016, the same problem: the fridge started to not get cold again. In addition to that, the ice would not come out from the ice dispenser and water from the water dispenser is not cold again. When my husband checked inside the door, the ice were all clumped together. They looked like they melted. And even the ice in the freezer bin looked the same. And on top of this, the refrigerator was making so much noise. The technician was just here again today.

When I purchased my Cabrio washer 31/2 years ago I didnt bother to check reviews since Whirlpool was suppose to be the best of the best. An expensive lesson! A washer that spits out codes?!?! Whos got time for this? We paid 899.00 plus taxes for it, now we paid a repairman 99.00 to tell us its not worth fixing. He said the bearings were completely shot. As he was leaving he said his next service call was for the same type of washer! Whatever happened to appliances that last! Going green is all the rage but yet everything from cars to appliances is built to last only a short while. Judging by these reviews I cant believe Whirlpool didnt recall their garbage!

The electric range was purchased June 2011. In June 2012, I purchased the extended warranty from Whirlpool (or their agent). The range is located in a summer cottage, so it has minimal use. I cleaned the self-clean oven last week after carefully reading the manual. Manual did not state to remove the chrome drip pans on the top, just “remove oven racks and storage drawer contents”. The oven cleaning caused the right rear burner pan to turn bronze/black. I called Whirlpool. I was referred to Warranty folks who told me they will not cover it because it is cosmetic and referred me back to Whirlpool (as it was WP instructions that were incorrect!) I called Whirlpool and they will not replace the chrome pan. I can purchase one. This is not my fault as aforementioned. I have been a Whirlpool customer for years. I will never buy another WP product. If they cannot write the instructions correctly, it makes we wonder about the product.

I purchased a Whirlpool Slide in Range Model WEG750HOHZ on March 23, 2019. After 7 days the oven would start on its own. I contacted Whirlpool Safety Team and they scheduled a service call. The following week the service company came out to tell me the computer that runs the oven needs to be replaced. Yet another week goes by to find out that they are still waiting on parts to come in. I should have demanded a full replacement oven. After spending nearly $2000 on an oven I can’t even use. Will never buy a Whirlpool product again.

As I write this, I am on my 5th service call in four months of ownership. The machine runs short cycles and requires us to not only do an extra rinse, each load requires an additional Quick Wash (with extra rinse) to get the detergent out. We use so little detergent that a 75 fl. oz. bottle has lasted four months with over 50% left. The techs Whirlpool sends are great. The call center first level people are fabulous. The supervisor is not helpful proclaiming that it was fixed. However, we still have to re-run the clothes every time.

Do NOT buy this machine. This has been the worst washer I have ever owned. There are times when my clothes come out of the washer and parts of them are STILL DRY! I pulled out a pair of pants I had worn while cleaning my attic and the cobwebs were still attached to the legs! Whirlpool basically told me, Tough luck, you bought it, were not doing anything, when I complained the day I bought it, and now years later it it continues to get worse. The machine was too expensive to just get rid of, but customer be warned - do NOT buy a Cabrio!

I purchased a high-end Whirlpool dishwasher (WDT710PAYM) a few months ago thinking I was making a wise upgrade. Poor design and it wont dry dishes or properly wash utensils when theyre placed in the utensil rack on the door panel. The unit heavily condenses after using heat dry mode and large water droplets completely cover the top of the inside cabinet. Eventually, they all fall down into the dishes and you now have wet dishes again. The Whirlpool tech’s response was to scratch the cabinet plastic with a scratchy pad, smear rinse aid over the plastic cabinet and that should stop droplets from forming. Whirlpool’s customer service told me they shouldve never told me that and what I should do is be there during the drying cycle and open the cabinet door to let the steam out. This is completely ludicrous. Dont walk but run away from Whirlpool products.

My husband and I purchased a Whirlpool Washing Machine & Dryer a year and a half ago. As of current, the machine has stopped working. The machine will turn on but will not agitate. It makes a horrible grinding noise. The type of washer we purchased was a WTW4900BW0. Whirlpool told us we should have purchased the extended warranty. But, I feel we should get more than a year and a half out of a machine that cost $650.

We are on our 3rd washer and second dryer in 10 years. Our latest replacement (Whirlpool Duet Washer and Dryer) was purchased 3 months ago and is already broken and now we have been without a washer for a whole month. Not only do they have issues with the control panel and latch, but they smell. The dryer also had a control panel issue. Trying to get our units fixed presented even more problems and wrong parts would come in, with weeks going by without parts/service. Apologies and sympathies expressed on the phone are not enough. When you buy a matching set and only one breaks, you tend to replace the matching unit, which we regret and we went back and forth with our washer and dryer. I would never recommend a Whirlpool product after this. We finally got a replacement today and due to more poor communication on their end, they could not hook up. My new washer sits in the laundry room, and I hate it before I even get it hooked up.

Our washing machine - as part of a stackable set - is two weeks beyond the one year warranty. Washer breaks down, I order the replacement part to find out - after waiting two months for the part - that the washer is now being discontinued so the ETA on the part is NEVER. Ask what Whirlpool will do about this and am advised that they will offer me a discount on a washing machine that does not fit on the stackable dryer. Or I can purchase a new washing machine at more than the original cost of the stackable set.This is a totally unacceptable situation. The washer is just out of the one year warranty period and it is already being discontinued??? Is Whirlpool making disposable appliances now so that after the one year warranty we just toss the appliance in landfill? Really? Unable even to purchase replacement parts to repair a one year old appliance? I will think long and hard about ever purchasing another Whirlpool appliance again.

I purchased a Whirlpool washer, dryer and dishwasher in 2004. The dryer and washer paint is peeling off the appliance and is rusting underneath. The dishwasher has never dried the dishes appropriately, it takes a few days to completely dry the dishes. I have lodged this complaint with customer service, also. I have always purchased Whirlpool, but I will never again nor will anyone in my family. I feel that Whirlpool should at least look into the problems and not just verbally apologize. Janice **

We have a 2 1/2 yr. old Whirlpool gas stove. We have had the mechanic here several times as it would not ignite. We also have had the control panel repaired twice as it melted. It is melted again but they will do nothing. I tried to clean the oven with their AquaLift technology and had to re-do it four times and still have residue which appears to be permanent. We are very frustrated with it. We have used Whirlpool appliances for over 40 yrs. but will not buy another. Model#WFG710HOASO, Serial#R21712236.

Microwave has melted a hole on the inside rectangular plastic cover. Model number is on recall list but not serial number. Opened microwave to find melted plastic on my popcorn bag that was dripping from the plastic up top. I will replace microwave but not with a Whirlpool again.

My stove hasnt been a problem from the start. I have had to buy two parts one for the oven, and the top. I feel my stove is dangerous. I would not buy a Whirlpool again. I would like to know who makes the stove that dont costs a arm and a leg. My stove is less than five-year old.

I bought a Whirlpool water heater in 2009. I paid $588.46 at Lowes. Turns out it is in a class action lawsuit for faulty thermocouple. I was given a coupon from Whirlpool for 2 new thermocouples as part of the class action lawsuit. The thermocouple goes out on it every 1-3 months. You never know when youre going to have a cold shower getting ready for work in the morning. I literally could have bought a new water heater for what Ive spent on thermocouples the last few years. The last two times it went out, I had to replace it twice within 1 day. Im sick of replacing it and have decided to install a new hot water heater. I am disgusted with Whirlpool and tried to contact them about it but have gotten no response. I will never buy another Whirlpool product and would not recommend them to anyone!

After 32 years of marriage and nothing but Whirlpool (because my mother swore by Whirlpool), that is all we have used. I am so disappointed in the Cabrio washer/dryer set we purchased at Lowes. After 18 months, the dryer just quit. The best part is, we hang clothes out most of the time. It was used one winter, $1400 wasted. We put a cheap Admiral in our second home and spent $500 total and they work fine. I will never ever purchase Whirlpool anything or recommend to anyone. Again, you lost a family tradition.

I have a whirlpool water heater. This is the third or 4th time that the upper sensor failure code has come on. Our water heater turns off all the time and we have to fire it back up. In the past few months, it has started pouring water out from the long tube on the side of it anytime we turn it on for more then 10 minutes. The last time we called a plumber, I was trying to get a quote on a tankless water heater. Ive been so fed up with ours and I thought that would be a better route to go. The plumber explained the negative sides to a tankless water heater and explained that our water heater was a really nice, really expensive and fairly newer model. I told him that I had just gotten it about four years ago. He said he could just fix that one. So after looking at it, he acted as if he didnt know what an upper sensor was and told me it was under warranty and that I should call for the parts. Every time we have called for the parts, they send the same box thing on the front of the heater and every time, it doesnt fix it for long before it says the same thing. And now, like I said, the water heater has now added the problem of pouring water out of it. I need help. I dont know what to do. Im tired of not knowing if Ill have hot water or if the water heater is going to pour out water. Im pregnant and worried that if we cant get this fixed Ill continue to have this problem along with having a baby to take care of. Please help.

I like the looks with brushed stainless steel and black. The most difficulty was getting someone to help get it and load it. But other than that, Ive had no problems with the dishwasher.

Our Whirlpool gas hot water heater was purchased and installed (through Lowes) in April 2008. In February 2009, the thermostat failed. Because the failure happened less than a year after purchase, Whirlpool replaced the part and paid for labor.The hot water heater failed again three weeks ago, and we contacted Whirlpool. We were once again provided with another thermostat, and were charged $135.00 by a plumber to install it (even though the customer service rep stated that there were known issues with this tank model). The tank is still not working properly. We (with our tenants) have tried troubleshooting according to their instructions, to no avail. It has been three weeks now, and no resolution.The heater has a six-year warranty. Not sure what this means if the product is defective to begin with. We pay to attempt to repair it?We will not be spending any more money on labor to install parts that may or may not work and have demanded that Whirlpool replace the heater. Whirlpool has refused to pay for any labor costs and told us that we must take the heater back to Lowes. So I suppose that means we have to pay to have a 3 1/2 year old heater removed from the gas and water lines, transported to Lowes, and a new one installed. What a deal.Stay away from Whirlpool.

I have been having a problem when washing my jeans in the Whirlpool Cabrio that I have never had before with my old washer. When I wash my jeans, there are always a few pair, never the same ones, that have an odor like dirty dishrags on them. I always hang my jeans to dry so I do not think it is this. I have tried to add a freshener to the wash cycle, it does not work. I have tried to dry them in the dryer with a scented dryer sheet, it does not work. I am assuming after reading these past complaints from other consumers that it is not getting all of the clothes clean because of the lack of water. I always use the deep water cycle, but maybe it is not enough water as previously suggested. I have had an issue with blankets and other heavy items not getting clean and/or not even wet. Thoroughly disgusted with this appliance!! I love all of my Whirlpool kitchen appliances though!

Two Whirlpool washers in six years that the barren in back of tub goes out. When the first one went out in the same month the warranty expired, I was told by a repair man that it was not worth repairing because of the cost. I purchased a brand new Whirlpool and only months later, the same parts are broken on this new front loader. How cheap is the Whirlpool app. made? Whirlpool wants to only send me a tech. to fix washer instead of replacing unit altogether. After all, the unit is only a few months old. I cannot believe I have to deal with this again.

Purchased a Whirlpool double door refrigerator and within a year the freezer and refrigerator doors were severely out of line. Called repairman who said the risers were broken, they were plastic and needed to be replaced. We did that. The doors were again out of line so badly that you had to push the refrigerator door side hard to get it to close. Repairman came today and stated he would recommend ditching the refrigerator as the risers in the bottom of the refrigerator are made of plastic and will continue to break. He leveled the doors but stated that they will continue to become out of line again.The repairman stated that this is a design defect in the Whirlpool refrigerator and he has replaced the risers in many of the refrigerators repeatedly. As if the refrigerator isnt enough, we own a Whirlpool Duet Washer and Dryer. Within 3 1/2 yrs the motherboard went bad in the washer and we had to replace it. The part and labor was almost $400. Whirlpool considered us a valued customer and offered us a comparable washer for $500 and they would take ours away for $20 extra. Only problem is that our original washer was $1,000 and the comparable was not as large as the one we had and did not have the stainless ours had.All I can say is if were valued customers I would wonder how they treat their less valued customers. All of this is to say that I will no longer purchase any Whirlpool products. Not only are the products below par but the customer service is non existent. They really do not care if they lose customers or not. They dont want to hear your woes about their appliances.

We purchased a brand new Cabrio Washer and Dryer in 2008 from Lowes. The salesman at the time suggested I purchase the extended warranty. It was because of the state of the art controls in the machines that could cost plenty if they had to be replaced. I was a bit skeptical at first. After several weeks, I returned to the store and purchased a 4-year extended warranty. This was probably the best money I expended in some time. In less than three years of ownership, I have had to use the warranty twice for the same faulty part (water control valve) that the repairperson told me was problematic. Then after reading the horror stories that consumers submitted to this website, I felt compelled to voice my opinion as well. I have been a die hard Whirpool product fan my entire life because they used to manufacture quality, long lasting products. I am moving soon. And I will have to purchase new appliances for the kitchen. But they will not be manufactured by any Whirlpool company. Shame on you Whirlpool!

Whirlpool top loading piece of junk! I would give it a zero star review if I could! Do not buy this machine!!! I agree with many other reviews. It doesn’t get the clothes cleaned and now a completely doesn’t work. We reset it, we’ve had the service guy come in and replace a bunch of parts on it. It’s past its one year warranty and doesn’t work anymore. Piece of junk! Junk, junk, junk!!! Waste of money. Do you not buy the Whirlpool tub loading washing machine!

I absolutely hate my Whirlpool refrigerator! The first day I had it, the cover to the deli drawer fell off and cracked because it wouldnt stay on. I called the company and they sent me a new one but it immediately fell off and broke also. It is just a terrible design. The plastic slots dont fit correctly and it just doesnt stay on.Then, a few months after owning the fridge, I notice rust spots on the bottom drawer. I called the company and a rep told me to buy dishwasher cleaner and a magic eraser and use that to scrub the rust off. She insisted that it must be near humidity. I explained that my GE stove and dishwasher, along with other stainless steel in my kitchen have never rusted. The Whirlpool company provided no help whatsoever and does not back up their warranty. I would never purchase another Whirlpool appliance after this experience. Now I am stuck with a fridge that has rust stains and a broken door.

We did our research and wanted to buy a new washer and dryer with a trusted brand that would last. Our previous washer and dryer (different brand) lasted almost 20 years. Our new Whirlpool Duet HE Front Load washer only lasted about 2 years. The washer started making a terribly loud noise when spinning. We had a repair guy come out to evaluate the problem and provide an estimate for repairs. He said the drum, bearings, and truing was all one unit and the repairs would cost more than the washer. The factory warranty is only a year. BIG disappointment in Whirlpool.

I took the time to read the owners manual, and then ran machine (washer wtw5000dw0). Using an affordable HE approved detergent (Xtra), I had no problems. If the washer doesnt fill or drain correctly, look up how to recalibrate it, was easy to do because I did that after transporting it. My clothes are cleaner, and I am using LESS detergent!

Bought a higher end Gold Series French door refrigerator. Immediately the door would malfunction and the the piece that pops out to seal the gap between the 2 doors kept piping out when the door opened...They came out and replaced it which did nothing...The repairman said we have to open the door slowly...Give me a break...Have a older cheaper model that is almost the same and its always been flawless.Now in year 2...the whole system shuts down out of the blue and thaws everything then suddenly works for a few months...Repair guy says cant do anything if he doesnt see the problem...Just got back from long vacation...We turned off the ice maker and emptied...Returned home to damaged wood floors and a bin full of ice...System reset when it restarted and started making ice...2 years old and we have a Samsung on order and the Whirlpool is going in the trash...Weve had many whirlpool products and the defects are getting worse every year...Absolutely done with them!

Whirlpool fridge (model no ETILFKXKS) - I purchased this fridge from a very good dealer (Trail Appliances, Edmonton). Within a year, I had my first of the frozen water drain from top freezer to water pan. Of course, I blamed myself - too much warm food, blah blah. Now this is happening more and more often. The fridge is kept at number 1 of 5 for coldness. All foods are left on counter to cool, but three times over my Christmas holidays this year when I swore I would throw this fridge in the garbage - the drain froze, water all over the fridge, food having to be removed and placed in other peoples fridges, blah blah. Now it did it again this weekend! There are only two living here. I work all day and no one even opens the fridge much and again this happened. Im really sad that such a faulty product (too much insulation hiding the drain pipe behind the fridge and it must be much too small in diameter; otherwise, it wouldnt freeze up). Talking about work. We have two fridges there with 50 people using them all day and they run perfectly for the last 8 years that I have been there. So I think it indicates that my fridge is faulty. Im so sad too because I dont have the money for a new one. I just turned 65 and am about to retire (single mom). You would think that a $1,300 fridge would last longer than 6 years!

I bought a top of the line Whirlpool dryer that cost me over $1,000. Havent had it for a month and it requires a service call. Have to wait two weeks for service! Totally unacceptable. The dryer is JUNK and now I am stuck with it. Horrible company. Bought from Home Depot.

I have Whirlpool Washing Machine bought at end of 2012. In 2014, I faced an issue where the washing machine board ics are gone. The services people came and check the replaced a board. It was cost me 6000 Rupees including the service cost. Very next year 2015, again the same issue. Board of the washing machine gone. Now I have to change the board. It seems it may cost more than previous one.I heard that these service engineers are taking the previous my board / replaced board. They are repairing it and sold it again and again so the quality of the board is question mark. As a customer I / we cannot spend money and change board every year. I just want everyone to think twice before you go to Whirlpool Washing Machine & its products. I had a same kind of poor quality issue with even water purifier too. Consequences - I have spent Rs. 10000 already, it is loss for me beside the buying cost of the products.

In April of 2016 I purchased an aqua clean self cleaning oven from Colders Furniture in West Allis Wisconsin. We were told by the sales associate that the oven was top of the line. This was a complete and utter bold face lie. I cleaned the oven for the first time the day after Christmas after having prime rib. I followed the instructions to a T on how to clean the oven. I had to turn the oven on 6 times and scrubbed the oven until my fingers were bleeding, not to mention the enamel on the inside of the oven is completely bubbling. I called the customer care center on December 31, 2016 and the representative basically said I was an idiot and did not know how to cook. They made an appointment to send a technician out on 1-5-2017. Before hanging up the phone the technician informed me that if there was nothing wrong with it that I would have to pay for the call. At this time I became irate and refused telling them that I have not even had the stove for 8 months and that it was still covered under extended warranty. I will see what kind of smoke is blown up my rear end. The technician is sending a new sponge and scraping stick. How about someone to also clean this piece of garbage. My advice is to anyone is if anyone tells you to buy an Aquaclean self clean oven from Whirlpool run in the other direction and do not buy it. Thanks Whirlpool for the garbage and for sending me cleaning products that are not even worth a damn.

I bought a dual oven Whirlpool 2 years back. This range keeps breaking knobs that are such a poor quality. I have bought knobs from Whirlpool 7 times already then got PSEG home service and they are tired with the quality itself. Save your money and buy another make! Poor customer service and the worst experience is what I have gained on buying this make. Have old mother at home and this headache only created more issues to help her with cooking.

I purchased a Duet several years ago and did not have a clue as to the problems everyone was having. Over the course of ownership I called the city to determine if we had a sewer leak. I had a plumber inspect our pipes. I felt really stupid that it took me this long to figure out it was the washer. I knew it smelled like mildew and have been using vinegar, afresh, Clorox until I am blue in the face. I didnt figure out that the sewers smell was also the same as the washers until I got on line and read about these machines. Finally, I lifted up the gasket around the door and it was completely black with mold. No amount of afresh was going to fix this problem. Do not purchase these front loaders. Feel like they should have been recalled and I really dont understand why they are still in circulation. I have also been having health/breathing issues and I cant help but think the mold is causing my illness.

Today I had the unfortunate experience to have to deal with Whirlpool customer service and claims. I WILL NEVER BUY ANOTHER WHIRLPOOL PRODUCT again! My refrigerator, that was purchased in 2013, has a door misalignment problem. It is a known problem with Whirlpool (service pointer W107317828). My refrigerator serial number and model number are affected. Because I am outside the one year warranty, Whirlpool refuses to provide service that is required to fix this known issue with my model/serial number. After having to talk to four supervisors the only resolution that was given was that they would cover the cost of the 7/16 hex nut ($4.33). Dont get me wrong I do appreciate the offer.The two supervisors that were below her assured me that no one can do anything to assist me further. The attitude of the second and third supervisor was pathetic. After over a hour on the phone I was so disappointed that I could not take it further. The cost that we are talking about that I am asking them to pay is $154.28. I am very disappointed. They say they stand by their product. To me standing by your product means that you will fix or replace any known issue. $154.28. I hope it is worth it to you Whirlpool. You lost a long time customer.

I bought a Whirlpool Cabrio Top Loader High-Efficiency Machine on March 20, 2013. 14 months later, it failed. When I called customer service I was informed the 1 year warranty had expired (I knew this already) and that all they could offer me was a $319 extended warranty to fix machine and guarantee covered future repairs. Luckily, I had the machine repaired at no cost to me after complaining to the sales people I bought the machine from the year earlier. They contacted their Whirlpool representative who had the repair covered. Now, 3 years and 11 days after purchasing it, it failed again. This time the machine would no longer spin out the water. Whirlpool offered nothing more than to give the website and special code for a discount on a new machine. After some haggling, they agreed to pay for 50% of the parts only, no labor. I argued this machine must be a lemon, as they have told me theyve heard no prior issues with this machine and that it would be reasonable to replace this machine. They refused any further assistance. So I threw this piece of junk away and instead, for $185, bought a simple rebuilt 15 year old Maytag washer with agitator, direct drive. Just a couple of knobs. No computer, fancy bells and whistles. I can say with absolute certainty that I will never purchase a Whirlpool product ever again. I also believe these machines are no longer meant to last like old washers (and dryers) used to.

Seems to use very little water. When I take the clothes out, they are bone dry in places which means they havent even seen any water! Clean (?) clothes end up smelling musty and I end up having to wash them two or three times which completely goes against any eco argument! I am really disappointed with this product and would never buy Whirlpool again. I have just washed our dog blankets. The cycle finished so took them out, had to check that the detergent had been used as the blankets were almost completely dry. The blankets still completely smell of dog so have had to put them through another wash (with more detergent – waste of money) and with a pre-wash cycle. Rubbish! We also have a Whirlpool drier and that is no better. Washing never comes out completely dry. It always has to be fully aired, sometimes more than others. There is no consistency in how wet or dry the clothes come out. Avoid at all costs.

Purchased washer 01/20/2012 after prior bad experience with washer, purchased from Sears. The washer is two years old and began making an awful noise and quit spinning the clothes dry. I too have had problems with getting service and cant see spending $500.00 for repairs on a washer that cost me $653.81 to purchase. Whirlpool and Sears better take their head out of their bum before the completely decimate their customer base. Why arent these problems being fairly addressed? It says a lot that your original warranty is only a year and any additional warranty is cost prohibiting. Save yourself some money and frustration and buy the old fashioned top loaders with standard agitation. AND WHIRLPOOL CAN AND SHOULD BUY A VOWEL AND REALIZE THAT IF IT DOESNT WORK IT ISNT MORE EFFICIENT!!!

I bought Whirlpool refrigerators around one and half year ago. After 1 year the light of refrigerator was broken. I was contacting customer service and arranged the fix. However, the contractor never showed up. After I making the call several times, I gave up finally. The repair is really bad experience!

This Cabrio Washer and Dryer are horrible!!! Dont ever buy one, they will not fix the F1 code, and Whirlpool customer service is non existent!! I hate this company, and will never buy a product made by them again! Be aware that Whirlpool makes products for Kenmore, Maytag, and a few others!!! I just want to spread the word about this washer! If you just bought one try and take it back for something else!!! STAY AWAY FROM WHIRLPOOL!!!

I bought a Whirlpool Cabrio Platinum washer 2 years ago and it is by far the worst washer I have ever owned. Its a water saving device with extremely long cycles. The clothes dont get wet enough, dont come out clean and they do not smell fresh. I have to put them through 3 rinse cycles and often times have to re-wash my clothing. The cycles are very long, using more electricity, and it takes me 3 times as long to get my weekly laundry done. My clothing comes out more wrinkled and twisted causing longer time ironing. My old agitator style washer did a superior job compared to this piece of junk. I dont like the automatic locking lid, nor do I like the machine choosing the spin cycle for me. There isnt even a soak cycle. If I want to soak my things I have to do it in the sink and then drag them to the washer to rinse and spin them.I spend a fortune on laundry additives in order to get my clothing clean and then they arent as clean as with my old washer. I now dread doing laundry and every time I look at the washer I feel like taking it to the dump! There isnt anything I like about this machine and I wouldnt recommend it to anyone. It is a piece of crap. This is 2016 and they havent learned how to make a good working washing machine. When I move, I will be celebrating leaving it here! I will never, ever buy a product made by them again.

After yet another frustrating round of laundry I have to write this. This has been the worst purchase (Cabrio 6800 Washer and Dryer) Ive ever made. Like other reviewers, I thought I was buying a high-end (high priced) product that has performed miserably from day one. Clothes do NOT come clean and for some reason, towels and dishcloths get ripped and shredded. All cycles (except sheets/towels) do not dispense enough water. Of course the one that does, results in the ripped and shredded problem. A little more than a year after purchase, we got an error code indicating the computer board was bad. Code would come up during initial cycle start and again at the start of the rinse cycle. Whirlpool basically said tough luck but shortly after, we started receiving offers in the mail to purchase an extended warranty for $175. Out of principle, I did not do this. Instead we discovered that we could push pause/start/pause/start multiple times and it would eventually keep going. We are still doing that on EVERY load of laundry (start and rinse cycles). I am not far from just biting the bullet and buying a new washer. It will not be a Whirlpool. One positive note is that the dryer has performed well, unlike some of the other reviewer experiences!

I will keep this brief because many of our issues on our 18-month-old washer are in other reviews. The anger I feel towards Whirlpool Customer Service and the logic they use in providing repairs on a “goodwill” basis are unbelievable. After a Whirlpool certified appliance repair person diagnosed our fairly new washer as requiring the entire guts to be replaced... transmission, bucket, etc., we were told the repair bill would be over $1,300! Are you kidding me... the washer only cost in the mid $500 range, and now Whirlpool is going to do us a big favor and cover that outrageous bill! I told the customer service supervisor to please give us a new washer and take away our broken washer and use it for parts (if there any good parts left in this miserable machine). His reply “thats not going to happen”. He used this phrase to us at least 20 times during our service call until I finally told him I thought his attitude was aggressive and demeaning. I refuse to be bullied by a major manufacturer for a substandard product.I can only warn you when considering Whirlpool (and every major appliance in our two homes are Whirlpool) that you should use due diligence in your selection. We paid extra to upgrade all our Whirlpool appliances in our homes and I will never make that mistake again. And don’t get me started on the white film that covers my dark clothes. They say I use too much detergent... not true. I am not stupid and understand the HE requirement to cut way back on soap.

I have the same problems as the ones listed in complaint section. I bought 4 Whirlpool products at the same time: refrigerator, stove, and the Whirlpool duet. Washer is a front loader. We have had nothing but trouble. The company we bought the machine from exchanged the washer for the same model because the electrical was bad and the parts to replace were back ordered for more than 3 months. We are now having problems with the exchange washer. This time it is the same as the engineer remarked in his complaint the bearings are bad and it sounds like a jet taking off. It’s that loud.I went down to the place of purchase and I am in the process for the repair. I have a feeling this will not end well. Whirlpool, if you call them, gives you a run around or tells you they dont have you listed in there computer. We dont have the money to replace any of this. This new machine is only 9 months old. Whirlpool is making a killing off of fixed income people and the working class. You tell me who can afford the cost of that kind of repair or the cost of a new machine that only works for a couple of months. Why is 60 Minutes not on them like a bad smell?

I decided to buy the Cabrio. It was the most expensive, but I wanted to buy American, and I liked the set. It does not do great with cleaning the clothes and they smell when they come out of the washer. Do you have any suggestions. It does not fill with enough water even when using the deep water mode. Please help as I would not recommend this. I called Lowes where I bought it, and they said they knew, but are not recalling, or making any adjustments until Whirlpool does.

We purchased the Whirlpool double oven gas range from Lowes in July of 2014. The oven heat that boils out onto the stove top when you use either oven makes it difficult to handle the pots on the range top. The first time I used both ovens at the same time the plastic front to the control panel started to melt and the fumes were horrible. It was under warranty so Whirlpool replaced it with an identical panel that also melted when I used the top oven and range top at the same time. Its out of warranty so Whirlpool says its not their problem. From reading these other complaints it is obvious to me that customer satisfaction is not important to Whirlpool - just that profit margin. Build cheap - sell high should be their motto.

This refrigerator was already part of the appliance package that came with the property. I dont think if I had a choice, I would choose this brand. The stainless steel finish has rust spots, the top shelf has cracked and it is less that 5 years old.

We bought our Whirlpool Refrigerator a little over three years ago. Within a few months we started having problems with the unit. From ice maker issues, cooling and freezing. Initially the frig was covered under Whirlpools 1 year warranty. Then our extended 3 year warranty kicked in through HH Gregg which they supplied for free because of their poor handling of the initial sale. We have lost track in how many times a repair man has come out to work on the refrigerator. In the last year alone its been at least 8 times. The most recent problem had been the freezer not defrosting properly to the point where we had to store food in our neighbors freezer. The repairman has tried everything he knows and is stumped. Well our extended warranty has run out but theyll continue to work on the problem as long as we report the issue within 30 days which creates a whole different set of issues. The extended warranty states they will replace the refrigerator if it has the same problem 3 times. However what they dont tell you is that if you call BEFORE 3 time period its considered a recall and that doesnt count towards the 3 strike rule. We contacted Whirlpool and they wont cover the refrigerator because the repair company isnt on their approved list. Really a Sears repairman isnt approved? So buyer beware of a lemon Whirlpool Frig! They seem to have a way of not covering their product.

I purchased a compact frontload washer. At first, I was getting a code f30, which took the technician weeks of coming to my home and changing different parts to finally accomplish that problem. After that, the machine would not go into high spin to wring the clothes out. So everything comes out soaking wet. After two different companies (Herbs Appliance and DanMarc Appliance which I got from my service contract) changed speed control, board, latch control, main computer, and top control board, the machine finally worked for a little while. Not long after, the machine is no longer wringing out once again. I am no longer under contract but had a repairman out three times to inform me this machine is a lemon. Whirlpool tells me I am no longer under contract, but my argument is this is not a new problem but a preexisting one.

Whirlpool Cabrio Platinum top loader 2014 model - This washer is an over engineered piece of junk. It takes forever to wash anything and it never gets anything clean. I wish I would of just bought the repair parts for my old machine which I had for twenty-three years.

We bought a new Whirlpool Dishwasher. Installed it, wife used it for two loads. The third time she tried using it the door sprung and it no longer latches. After two weeks of calling Whirlpool, we finally had someone come out to fix it. After the repairman took a hammer to the frame he stated that it had been dropped. He wobbled the dishwasher back and forth with his hand. He said the frame will never be correctable and we will always have problems. After another week we got a hold of Whirlpool and were told the repairman has ordered parts to repair the dishwasher. Whirlpool is hoping it will hang together until the warranty expires. If the dishwasher were fixable that would be fine. However, when the repairman who has years of experience in his job tells me it will never be right and will always be a problem, I believe him.

In July 2012 we purchased a new Whirlpool Gold refrigerator. Last month ice maker went out. We bought it at Best Buy. They sent out a third party repair co. subcontracted under Geek Squad. Response was same as all these threads - just have to replace it. Since Whirlpool does care why dont we all go after place we purchased these refrigerators or the suggestion of a class action suit works for us! This is absurd!

Soon as warranty expired issues with product. This should not happen. Made in America, washer making too much noise. Products cost more but poor quality. What is this company going to produce? This is the world we live in.

My wife and I made the unfortunate mistake of purchasing the Whirlpool Gold Series, model #WRF989SDAM00 refrigerator two years ago...yes TWO YEARS AGO! We have experienced numerous issues with the appliance but our latest (no cold air in both the fridge and freezer) prompted a call to a service center. The serviceman that showed up knew immediately what the issue was, our compressor and evaporator had malfunctioned and according to him, We have seen the same problem in a number of these models and that Whirlpool has since redesigned the casing to prevent this issue in new models. What about those of us who purchased the previous model?! Now shame on us I guess for not purchasing the extended warranty...I suppose I just took it for granted that in todays competitive manufacturing world Whirlpool would be committed to building a quality product! Because of this I was offered two options from Whirlpool. #1 - pay for the parts yourself...over $800 or #2 - purchase their 1 year warranty program @ $350/year, this warranty will cover all parts and labor for an entire year. Based on my experiences though, I will need to purchase a 1 year warranty @ $350/year for the life of this lemon, potentially costing me $5500 over a 10 year period. I ultimately took option 3...tossed the piece of junk and bought a new fridge from their competition. Dont be fooled by the attractive design and appearance, the Whirlpool Gold Series refrigerator is a money pit waiting to happen!

When we bought our house the Matching set of Whirlpool Cabrio Platinums came with it as they were new. I decided to keep them and sell my LG Troms.Absolutely the worst mistake was keeping these Whirlpools. Who in their right mind would consider a washer with no agitator a washing machine? The clothes just sit and do nothing. They don’t get clean at all. Its a complete pile of useless junk and the person or persons who engineered it shouldn’t even be in charge of designing birdhouses.Whirlpool themselves should be ashamed to put out such a pile of garbage to the consumer. Our house came with all new Whirlpool appliances and we are going to replace them all and never give Whirlpool a look again. Whatever you do don’t fall for the shiny unit, slick salesmen. Because all youre going to get with Whirlpools washer is all talk and zero action. Thanks for the not so clean clothes Whirlpool. The local laundry mat thanks you when I need to actually clean my clothes.

Bought this washer NEW 4 yrs ago. Now sounds like a freight train in the house when in use. Whirlpool customer service is absolutely USELESS!!! They do not stand behind their product and refuse to acknowledge what is a common issue. PISS POOR and will NOT give me a number to a higher up. Absolute disgrace!!!UPDATED ON 10/28/2015: This is an update to my previous review. 1st, I contacted Whirlpool who was absolutely NO help whatsoever and the person I spoke to refused to put me through to higher ups on the food chain. I was wrong in my previous review when I stated that we purchased the washer & dryer 4 yrs ago. It was purchased in January 2012. Started making noise in 2014 and has progressively turned into the sound of a freight train. I also failed to mention the stench that comes from this machine. It has also got to the point where it quits with 10 minutes to go in every wash. Whirlpool did send out a Whirlpool certified technician, which they paid for, who stated this has been a common issue with these and other models of Whirlpool Cabrio wash machines. Says in his 3 yrs with the company he has seen and diagnosed over 30 machines with basically the same issues (bearings are SHOT) and Whirlpool refuses to accept any responsibility for the defective design and that, in his opinion, they shouldve never been released. He gave me an estimate of $257.13 to repair. We decided to go ahead with the repair and technician came out only to tell me that there has been a re-work in the design of the replacement parts as Whirlpool realized they were faulty. So I now have to wait for the NEW designed replacement parts to come in as they are back ordered. WTF does that mean??? Shouldnt there be a RE-CALL and shouldnt they accept responsibility for this??? This has been, without a doubt, the most disappointment weve had with any purchase of a NEW appliance or, anything else for that matter, in our lives. After reading through some of these same complaints Im wondering if this machine is nothing, but a money pit and whats going to go wrong next. We also purchased the Cabrio dryer at the same time and have had no issues with it as of this time, but I assure you, I wait with baited breath. Their customer service department is piss poor AT BEST!! Please, stay away from ALL Whirlpool appliances in the future.

On 02/25/13 we purchased a Whirlpool Gold Series side by side (French door) refrigerator with an ice maker at the cost of $1,850.00. In April of 2014 the ice maker stopped working and the freezer at the bottom would not freeze food. Luckily for us it was still under warranty and was repaired. At the time of the repair, the repairman (associated with HHGregg) told us that the refrigerator should have been replaced since the cost of the repair was more than the fridge itself. Now July 20th, 2015, the same issue has surfaced. Again the ice maker will not work and the freezer wont freeze. I would not recommend this product or if you do pay the extended warranty.

It is a double oven. Temp varies too much. The oven is very inconsistent. Cooking Thanksgiving the temperature would not stay even. It took much longer than intended. It was quite frustrating. I would not recommend the Whirlpool double oven.

I have used Whirlpool products for over 30 yrs. This is the worst made product I have ever purchased. The ice maker doesnt produce very much ice. The cold water on door isnt cold. There is too much wasted space in freezer and refrig. side. You cannot get anyone to call you back to call for help. I contacted Whirlpool over a month ago. No return call yet. Consumers beware!! Model no. WSF26C3EXF01.

We purchased the Whirlpool Cabrio washer & dryer. The glass lid design is VERY POORLY constructed and should be replaced by Whirlpool. We paid over $200 the first time the lid broke and was told this is going to be a continuing problem. They were correct! We subsequently replaced the lid 2 additional times only to have the same break on the right hand side causing the lid to pop up. Something must be done and WHIRLPOOL need to care for their machinery. They should replace the lids or provide a major incentive for consumers to replace the washer. PLEASE DO SOMETHING!

In 2006, I paid $1,300 for above fridge and bought extended warranty. Within a year, I had four service calls for condensation in bins that causes freezing of lunchmeat, veggies, etc. and anything put in them. The A&E service company said to use plastic bags and then said I should keep the bin drawers open at an inch so air could flow. Next call said vacuuming underneath would solve it. Final call said again to use bags and suggested modifying the fridge by making a hole in the sidewall (which would nullify the warranty).Since I declined modifying the fridge, he contacted Whirlpool saying I declined service. I still have this problem, was going to call for service because I could really use the space the drawer provides but I have a feeling I will just be throwing money away. I was going to contact Whirlpool but Ive done that too. I feel totally ripped off on an item that should have quite a few years of service left.

I purchased my new washing machine in September 2011. When I removed the clothes from the washer after the first wash, I noticed that there was soap on several of the items. I ran them through another rinse and spin cycle, and there was still soap on several items. In an effort to avoid this problem, I no longer use the soap dispenser tray, and use the bulky cycle to get more water in the tub. Like most of the others, the clothes are tangled and stretched from one side of the tub to the other. Also, it takes 1 hour and 36 minutes to run a complete cycle. The manager of Sears tells me, that because of government regulations, that in a few years, you will not be able to buy any other type of washer. I purchased this machine, because it was highly recommended by Consumers Report magazine. I filed a complaint with them eight days ago, but have not had a response.

I paid about $400 for this dishwasher and the regular price was over $600. Got a good deal. It washed dishes wonderfully. All I had to do was scrape the chunks off. It cleaned the rest. BUT... at a certain point, it started NOT cleaning. It was only about 6-7 months old. It was to the point where everything just came out kind of slimy and food grit was re-deposited on the dishes. I cleaned both filters. I made sure there was enough Rinse-Aid all the time. I ran hot water in the sink before starting to make sure the temp was hot enough. My husband went online and someone had instructions about cleaning the water intake because it could sometimes have sediment buildup. Not a difficult process, but there was no gunk in the intake filter. When I listened to a load it seemed like it drained, (most start with that), paused, rinsed for a couple minutes, paused, drained, paused and refilled for the wash cycle. So the pump worked, the arms went round and sprayed. Nothing was in the way of the arms. After it started the wash cycle, it seemed to just stall. It would spray for about a minute and then stop. Im not sure it sprayed after that. The timer kept counting down. It said dishes were clean, but it was an absolute waste of time. I was ready to go buy a cheap dishwasher and throw this one in the dumpster. I think it is a 720 padm??Just after my husband checked the water intake filter, we started another cycle. When it was rinsing, he opened it up and everything seemed to be working ok. It drained, then filled and started the washing cycle and then stopped. He opened it back up and surprise, the water was full on the front level by the float (that turns the water filling off). But in the back of the dishwasher, there was only about an 8th of an inch of water. Online it said the water should fill to just about the top of the heating element. It WASNT. Problem? It wasnt LEVEL. The instructions when installing said it should be leveled. We did when installing it (when it worked great). But looking back, we put in a new hardwood floor about the time it stopped working ok and we didnt put 2 and 2 together. We did not re-level. When we pushed the dishwasher back into its built in cabinet, it must have gotten OUT of level.The rinse part worked I guess. Then it drained and re-filled. After re-leveling the dishwasher, we opened the door at that point. The water was a level depth front to back and side to side. My husband explained what he thought had been the problem to me. When the wash cycle starts it fills, the float shuts off the water at the appropriate level. THEN... the dishwasher starts to pump and fill the arms and the tube up the back that feeds the upper washing arm. So much water goes into the arms and up that tube, the dishwasher looked almost empty of water again. As the dishwasher was now level, it began adding water to compensate for the arm/tube filling. Before the float would shut off too soon because the front part of the tub was full but the back wasnt. Without enough water, the dishes were NEVER going to/COULDNT get clean.The re-leveling made sure that the float didnt turn off the water filling until there was much more water, the CORRECT amount. The next load cycled all the way through, spraying much more than Id heard before and the dishes were clean. P.S. I also got some dishwasher cleaner and used that on a couple empty cycles. I NOW LOVE this dishwasher again. FYI If my husband wasnt handy Id have junked this thing. We HAD leveled the dishwasher when we installed it. Just didnt realize it COULD get un-level just pulling it in and out of the cabinet to install new floors. Check out all the troubleshooting stuff in the manual. But if it doesnt help, put a level inside across the bottom rack, front to back and side to side and make sure the bubble is in the middle of the two lines.The previous dishwasher I had, just made like a fountain of water that went up the middle of the dishwasher into a sort of funnel filling the upper arm. THIS one has that tube up the back and it curls down under the filter and Im guessing it is more sensitive to being OFF LEVEL, because the tube doesnt go straight down, it curls and lays across the bottom of the tub. Without being level, there was never enough water to suck up that tube to start the the actual wash cycle and it just stalled there till the timer said clean at the end. IE: dishes never did wash. BUT IT DOES NOW! Woohooooo!

On October 21st 2011, Michael sent their technician, Steve, to my residence to check my washing machine. I was in the house the whole duration of his visit. After testing he concluded that the control board of my machine is faulty. Although he brought with him his own control board but he never showed me my machine working when he installed his control board, even though I was in the house at the time. With my lack of knowledge at the time, I missed requesting that he show me the machine working with his control board. But he should have involved me in the diagnosis since I was just home and should have been his initiative. Anyway, Steve then said that the total cost of the control board plus service is $194.03 on top of the diagnosis fee of $81.19. I was taken aback with the cost since working used washing machine on Craigslist just cost $150. So I said I can only pay him for his diagnosis of $81.19 by personal check. He issued me an invoice with account number **. I also thought that I also could get a cheaper control board online which I did. Also, I know I have the right not to purchase control board from them as long as the diagnosis was accurate since I paid for it. So I ordered a control board from ApplianceZone.com and also chatted with a technician named Kelly. Based on the symptoms I related to her, Kelly confidently said that the issue is not with the control board but the Control panel is the one that is faulty. Kellys diagnosis was different from Steves but since Steve has personally checked my machine, I decided to purchase a control board. When the board arrived on Octpber 25th, I immediately installed it as its easy to install since I followed simple instructions how to install it myself. But when I installed the new control board it manifested the same issue as the original part.. So I called Steve over the phone and he said the new control board.I purchased also faulty and that I have to replace it which I did. Then the second new control board arrived on November 8th and when I installed it, exactly same issue again manifested. That was then I suspected probably Steve misdiagnosed my Washing Machine. So I tried calling Depew the same day but wasnt able to reach Steve. Instead another guy named Kenneth answered the phone. He said that Steve has the right diagnosis but I insisted that I recalled Steve never showed me the washing machine working with his control board installed so Im doubting he got the correct diagnosis. Since it wasnt helping me at all, I decided to visit personally their store on November 8,th 2011 at 5933 Burnet Rd Austin TX, to request an audience with their manager. Then I met the manager named Michael ** who I believe is also the owner of the company. After introducing myself and explained the issue and told him that I wasnt satisfied with the service rendered by Steve because with two new control boards why is my machine still not working so I believe Steve got an incorrect diagnosis. I was a dissatisfied customer and I was hoping they would find a way to help me since I already paid them $81.19 but to my surprise, this Michael ** was so rude, his response was We have done our job, you are on your own now. We dont need your business. Good Bye I said Is this how you treat your customers? he answered me This is how I treat you.. I felt discriminated and insulted by his unprofessionalism. I couldnt imagine an owner of a business treating a customer like that. Before I left, I told him that I will report him to Whirlpool since they referred Depew to me and I would also report to the Texas Attorney General. He just said Go ahead and do what you want to do. We have nothing to do with you; I couldnt believe we have a business owner like this here in Austin TX. I really appreciate you helping me with this issue with Depew Appliance especially with this issue with their manager Michael Depew. I also demand refund of $81.19 for the diagnosis as they dont deserve to be paid and also they should pay me the cost of the control board $85.13. Lastly, I like to request that whatever license this company is holding must be reviewed as his dealing with me as customer is nothing short of discriminatory.

In the last two years, the inner glass door of the oven has exploded. The last time was Tuesday, 14th January. The oven door was ajar because we had just finished cooking dinner. The noise was deafening but the worst thing about it was the large pieces of glass thrown all over the kitchen. Most of which were large enough and sharp enough to kill a child and seriously wound an adult. I phoned Whirlpool to report this. The operative I spoke to was very polite but told me these things happen and I could have banged it a while ago and left a weak spot! She also said a Supervisor or similar person would telephone me that day. It is now Saturday 18th January and NO phone call. MY concern is there is no mention of this being a possible problem in their literature and their obvious lack of concern under a Health and Safety situation. Not to mention the cost of replacement door glass.

Purchased the machine in 2008 for $800. I did not have any problems (wash 3-4 loads/week), pleased with the washing until July 2015 when the machine was spinning out of control and the machine moved approx. 1 foot across the floor (thank goodness I did not have it on a pedestal as it may have tipped over). I canceled the run. This was a fine washables load of 5 sweaters placed on a medium spin.Scheduled the Whirlpool authorized service tech to come out and fix. He indicated there is extensive repair required and would cost approx. $1800. And indicated he has seen this failure before and it is due to the plastic parts inside. Also, he has seen these washers last about 5-7 years before replacement. Wow, last washer I had was a Maytag and it lasted 15 years costing 1/3 the price of the Whirlpool Duet. Now perplexed on what to buy, called Whirlpool Customer Experience Center to register my complaint and asked if there were any updates to the product that would avoid this failure. The center indicated there are updates but they are confidential and did not know if this failure was addressed.

I felt compelled to write this review, to sum it up NEVER buy ANY Whirlpool, KitchenAid etc brand. Nothing but the worst experience, it all started with a 5 year old Whirlpool fridge that stopped cooling, I called and they said they could send someone for like 200$ and that it does not guarantee it will be fixed. So I called an independent and he tried to refill the freon, but it was leaking behind the fridge in a section you cannot access because they want you to buy another one, so 5 year old fridge in the garbage and now to top it off, a KitchenAid knife set that is barely used, one of the big knives broke cutting a fruit, and good luck in any circumstance getting any customer service. SO NEVER AGAIN, TRUST ME AND PUT YOUR MONEY ELSEWHERE ON ANY OTHER COMPANY.

Love the dishwasher, except the racking which has some top rack channels which are too small to be used by glasses, mugs, etc. The Power On/Off should automatically power down when the cycle is finished. Too often when someone leans against the dishwasher while opening the overhead cupboard, the dishwasher will start up because the unit was not powered down.

I bought my Whirlpool Cabrio Washing Machine in 2010. I hate it 100%. I have never used bleach in the machine. I use liquid detergent only. 2 things happen every day: #1: When I wash a load of colors, I take them out when complete and there is dry white powder like substance over the black clothes. It looks dirty but it just got washed. #2 About once a week, I will pull something out of the washer and there is a bleach spot on it. The last item that this happened to was a $200 sweater. It went in the garbage. This should never of happened with an $800 washing machine.

I purchased an over-the-oven microwave in November 2020 (Model # WMH31017HZ). It worked until March 2021 then began tripping breaker. The Safety department at Whirlpool stated that I have to get a dedicated circuit. After spending an enormous sum to get that dedicated circuit the microwave worked until April when just opening the door caused a spark that the electrician and I observed. By now I am sure that I purchased a defective unit but Whirlpool was not believing it. (As as aside, expect to stay on hold for at least 10-30 minutes when you call Whirlpool).May 7th the serviceman from Guincho ordered parts that was needed to repair the oven. As of May 30th the part still had not arrived. Finally, after multiple calls and excessive hold time, Whirlpool agreed to refund my purchase price and as of this writing on July 26, 2021 I have not received it. In the meantime I purchased another brand microwave and have to look at their defective one until they decide to pick it up. They have lost a customer.

Just plain terrible. Purchased Whirlpool Gold Seris Dishwasher Model w10698637a in June and now its been 3 attempts so far to fix a brand new dishwasher that does not clean. So far I have been asked... have you been heating the water before you start the cycle?, my favorite... Is this a whirlpool dishwasher. So I find out today that it will take another visit from a company that hasnt been able to fix it, plus a call to the tech line to make sure they havent missed anything. Heres what Ive missed, a dishwasher that cleans.

Purchased above refrigerator (WRF736SDAM13) over a year ago and it has been nothing but trouble. Ive had service companies out 6 different times. The doors never lined up or closed properly from day one. The final and last attempt to fix was putting caulk in the seal of the doors!! Left door does not seal properly and moisture builds up on inside. I requested several times for a new one and Whirlpool refused. Also purchased microwave, stove and dishwasher. Microwave went out 6 months after using it. They had to replace a major part. At least they did this at no charge. Just the hassle of having to be home 2 times to meet service tech. WILL NEVER purchase Whirlpool appliances again. Ive been using them for in all my homes in the past. STAY AWAY from this model.

We had the same thing happen. We purchased a brand new home and within 6mo the plastic around the handle started breaking off and pieces would fall into any food that was being cooked on the stove. Whirlpool fixed it for free but now the same thing is happening with the new door.

We bought this double oven range and then find that two element cooktop sometime work and sometime do not even the indicator light is on. Please tell me how to fix it. It cause me headache.

I purchased the Whirlpool Cabrio washer and dryer about 5 years ago. I wanted to pay for a good pair to last a long time for the money. We have had a repair man out twice for the washer. They ended up replacing the computer board. It worked fine for a few years. Now, it keeps getting the unbalanced error code for almost every load of clothes that we start. Sometimes, it takes 20-30 minutes of rearranging the clothes to get it to finally work. I have had to manually set it to finish the loads on a number of occasions. It is so time consuming to do laundry due to having to play with the clothes to get the loads to finish. Plus, I dont know how many times it has woken up my grandkids because of the loud thumping noise it makes when it gets unbalanced. I have never had a washer do this. I would expect when you pay big bucks for an appliance that it should last a long long time. One usually gets what they pay for. I should have bought a cheaper pair. Then, they probably would have lasted 15 to 20 years.

Purchased both Cabrio washer (wtw6200sw2) & dyer brand new in 2007 for $1200. Within 4 years the motherboard went out. Whirlpool didnt want to fix it. They said it was past warranty. After many complaints to corporate, they sent someone out to repair it for $496 (they paid). Repairman said these models had motherboards from Japan & Whirlpool was aware of the many issues, but wouldnt do a recall. 2009, the springs went out, 2011 F codes began to appear. Clothes dont get clean; not enough water. 2014 & 2015 DU & DL codes appear. Now I need a new Lid latch assembly. These washing machines are not worth buying. Never again will I buy another Whirlpool!! My mom had an old Kenmore that lasted 20 years and only needed a replacement belt. No more fancy high end washers for me!

Light bulb went out in the freezer. Come to find it is a led cluster with a circuit board only cost $30 to $100. Engineer should be fired. What is the reason to take simple bulb and custom bastardize into an expensive hybrid. Greed.

I installed this Whirlpool Gold Series oven in December just before Christmas. I cooked a 9lbs Turkey for over 4hrs at 350 degrees (it should have only taken 21/2 hrs at 325) used a thermometer to test the temp. Well the breast part was fine but later in the evening I removed the entire turkey only to find that the legs, thighs and bottom of the turkey was still RAW. Lucky no one had asked for that part of the turkey. Next I tried a small prime rib roast. Same thing happened. The top of the roast was fine and the bottom was RAW. I dont dare cook anything in the oven now. Called whirlpool and they are going to send someone to look at it but I wont hold my breath for any results. After reading the same complaint on several reviews and the TV show Marketplace it seems to be pretty standard for this product.

The double oven is the best! Doesn’t heat up the house like the older stoves! Very easy to clean. The range is all one level, so it is at easy to set your pit anywhere. Also the middle burner is amazing for a griddle!!

I purchased an extended warranty with my product purchase and only a year and a half into using this brand washer the lid broke on one side at the hinge, it looked really rusty and like others I thought I was making a very decent purchase because all of my previous appliances were Whirlpool so figured Id keep up with the brand. Sad to say that was the worst decision I could have ever made for 13/1400 dollars for a washer with a light inside. Never again. They wouldnt even keep up the warranty because they said it was too expensive to repair it. Whirlpool is very bad for business...

These reviews re Whirlpool washer proves I can no longer trust Consumer review. This washer is junk. Does not clean, Takes over an hour to not clean your clothes. I have to add water to cover the clothes. They come out as dirty as they went in. Want an honest review? Check out the ones on Amazon.

I purchased a new Whirlpool Cabrio set, in 2009. I bought the top loading washer, and matching dryer. Since 2009, I have had the washer serviced FIVE times. Bearings, water pump, F1, F2, ul codes, and a few other things, I honestly cant remember. I love this capacity. But that is all I love about this machine. Today, the water pump went out again. I have been reading online regarding loose coins making their way into the drain pump, the hose, and other parts of the washer. I am diligent about emptying my pockets, but, obviously, someone in the house is not. There should be a trap for the coins, buttons, and any other debris that passes through, but, clearly there is not, and it appears I am not the only one with this problem. I am so frustrated. I paid almost $3,000.00 for this set. It was my very first brand new set and I have had so many problems with this. With all of the problems and all of the complaints, and so many similar complaints, why is Whirlpool not acknowledging them? Why are they not doing anything about it? Side note, my dryer works fine.

I am done with Whirlpool. Everything I have bought is failing. I bought all new appliances when moving into my home. Dishwasher, 2.5 years old, quit. Cost is going to be as much as a new one. Refrigerator quit at 5 years old, what a mess that was. Paint is peeling off my clothes washer. I am not going to buy or recommend any more of this junk.

After purchasing three gold series kitchen appliances in 2013 two months after purchase refrigerator failed. Whirlpool did not have a fix at the time. Told me I had to wait two months for a part to be engineered and then service to be scheduled which is not acceptable. They would not take back the refrigerator and give me a different model so I had to press Lowes to accept it back and they did give me a refund. I then had to purchase a different brand refrigerator which now I dont have a matching set in my kitchen.Then the dishwasher became part of class action lawsuit and now my gold series gas range is obviously damaged too. The control had the plastic panel is bubbling and it is split. Again after talking with Whirlpool customer service they refused to help with this at all claiming this is a cosmetic issue and it wouldve only been covered for 30 days from date of purchase. This gas range also has an aqua lift self-cleaning feature which does absolutely nothing. It does not clean the stove. You have to go into it and clean it the old-fashioned way with chemicals, gloves, mask and a scrub brush. These products are absolute junk and the customer support is non-existent. Do not buy Whirlpool products.

My oven is less than 2 years old. The blue enamel has had cracks for over a year & was told its cosmetic & theres nothing that they can do about that. Now its starting to pop off. I found a few slivers in a vegetable dish! Now I cant even use the top oven because of this! It seems to only affect the bottom of the top oven. I feel that the temp may be getting too hot for the blue enamel which is another safety concern. I have contacted Whirlpool/KitchenAid to be told that if they send out a repair person he would just use a marker on chips. I was told they would give me an employee discount from $3000 to $1800 to replace but I would have to act right away for that price! Really? My oven is only 1 & a half old.When I started researching this problem I am having I found many complaints of people having the same problem! As a consumer I feel so mad & frustrated that they are not doing anything about this since its an ongoing complaint from so many dissatisfied consumers. I do believe it is a safety & health risk now that its showing up in the food that has been cooked in that oven. I would urge anyone thinking of buying a Whirlpool/KitchenAid cobalt blue enamel oven not to! They will not stand behind their product & you will have to replace at your own expense. Shame on you Whirlpool!