I like the Kenmore dishwasher as it has the cutlery basket in the door. This leaves more room for dishes on the rack instead of taking room up for the cutlery.

I bought a pair of Whirlpool front loading washing machine and dryer on May 23, 2011. The Duet Steam washer model is WFW9640XW, dryer is WED9470WW. Their high retail price was $1125 each. I did not pay this for them. I thought I got a great buy at Lowes for the price I paid, plus their 4-year extended warranty. Whirlpool used to be a very high-end appliance manufacturing company. Now, all they put out the back door is junk. I would advise not to buy Whirlpool front end anything. My washing machine started making noise about 2 weeks before I reported it to both Lowes and Whirlpool. The noise sounded like bearing not being lubricated, which that is what it ended up being.The noise got so loud that even with all my very expensive electronics (my home entertainment ctr equipment) I could not hear the TV which goes through an expensive Yamaha AV Receiver and those expensive Infinity speakers 7 channel system. The main bearing for the wash drum assembly was bad. After two emails and several phone calls to both Lowes and Whirlpool, Whirlpool was going to send the so-called re-engineered drum assembly. The style I have is 3 parts; the new one according to Whirlpool is one part, but if they put the same bearing in, youre going to end up with the same problem in another year. I live in a condo of just over 920 sq. ft. so really there is no room to repair them in my home, but that is what they are going to do. I will be getting the new drum assembly delivered to my condo and have the repair company doing this dirty job in the middle of my living room.Living in a condo, I have a small utility closet next to the kitchen where the furnace, hot water tank, and washer and dryer are. The closet needs to have some areas cut out with and installed two small hinged doors on each side, so if anything ever needs to be repaired or replaced, there would be a little bit more room to move items in or out. The problem getting the washer out is getting the dryer moved so you can disconnect the electrical plug, cold water hose for the steam, plus the vent hose. First, you have to get to the water valves which are very hard to reach. Because of the way cluster housing is made, they squeeze things into very small holes like the faucets and drain hose are located. I was asked by the repair person if I could help him lift these items out of the closet. I have had 7 fusion back operations and #7 left me in constant pain that I take a narcotic drug for pain daily. So, I called Whirlpool back and said the repair people were only going to send a tech. I was told that it is a two-man job: one tech and one helper. So Lowes needs to authorize two people since Whirlpool is sending the new drum assembly for free. I wish I could have gotten a new washing machine with the so-called re-engineered drum assembly. I am still probably going to have to squeeze between the bulkhead (wall) and the washer and dryer to disconnect everything since I am a small person. If I wasnt retired, I would have bought a different brand front loading washer and dryer, probably Bosch and took the loss on these piles of Junk. I love my country and do my very best even as hard as it is in this day and age to buy US. I served my country in the US Navy during the Vietnam War, just to see the civilians willfully buy Asian everything. So now, we have 4 Asian nations that own this country. I dont know why Whirlpool changed from a company that you could trust their products to a company that doesnt give a damn what they put out the back door. These companies still havent gotten the clue why folks buy goods from other countries. I think they need to open their eyes, but I guess with Whirlpool still being a company that is selling a very large number of appliances and making money off of us, suckers, they dont need to change. The only way they are going to change is if folks stop buying their junk.

The machine meets our needs and just the right capacity. It has just the right number of selection for proper washing. Very easy to load clothes and remove from the washer. There were a number of colors to select.

Mind you, Whirlpool products that we have purchased in the past have been satisfactory, but gas hot water heaters, no! About four years ago we purchased a Whirlpool hot water heater that went out in a little over a year. After spending many calls and time, we found out that the HWH was on soft recall. Whirlpool credited our account, but this was to purchase another Whirlpool, which we did. We paid for installation. About 2 years later, it has gone out. Same problem. Lowes says not their problem. Whirlpool says it will pay for the part only. Plumber will cost 150-200 dollars. All the plumbers I have talked to will not repair them, then they are held responsible when it goes out! As a disabled Vet I cannot afford to throw 400-600 dollars away. And, Whirlpool tells me that if they give me an RA number to replace the HWH, it will have to be a Whirlpool from Lowes. Great! Whirlpool quarterly report looks very good. Mine doesnt look as good. What can be done about a poor working product? Or is this too big to fail? Let me know.

The machine is reliable, does not take forever to do a load, it is relatively quiet. It has sufficient options depending on the size of the load. Additional options are time setting, choice of warm, cold or warm/cold water settings. On light and medium loads it extracts almost all of the water; on heavier loads an extra dry spin does the job. In all the years that we have had it, it has required only one service call. The maintenance man told us that this model is the best in a series and he recommends that we hang on to it for as long as possible. We're very happy with it.

We bought this Whirlpool Cabrio washer 2 years ago and have hated it since the first load. It does not clean clothes, and the so-called large capacity will barely clean 5 regular towels. And if you wash diapers, do not buy this washer. If a load is really dirty, you have to wash it 2 or 3 times for clothes to be clean. Then, there is the awful mildewy, moldy smell after a few washes. How can a washer that gets so bacteria-laden be allowed to be sold on the market. Ive been washing laundry for 45 years, and Ive never had this kind of wash-related problems. This washer is an overpriced nightmare. I cannot wait until I can save enough to replace it. And I am watching and hoping a class action suit comes out to force Whirlpool to take these washers back, refund the money spent, and apologize to all the people who purchased one.

My house was built in 2004, therefore the Whirlpool water heater was installed in June 2004. The water heater broke down (It flooded my garage) in 2007. I didnt have to pay for the water heater at Lowes (It was under Warranty), but I had to pay for the delivery and labor. Now, I had to call customer service, because the Whirlpool water heater installed in 2007 has problems too. The pilot light would not stay lit. I have to pay a certified technician $180, just to come to my house to fix this problem, when this is a recurring problem, with this Whirlpool water heater that was purchased at Lowes. (The heater has a six-year warranty. Not sure what this means if the product is defective to begin with). Im very disappointed with this product. It has too many problems, and I have to pay for a defective product. I would stay away from Whirlpool if I could.

Whirlpool Cabrio washer - Its very expensive and it quit after 3 years. Repairman said computer component went out and it would cost $450-$520 to repair and it wasnt worth it. He also told me I should have read reviews first. Whirlpool said I should have bought extended warranty. No more Whirlpool appliances will be bought for our homes or business.

In 2012 we purchased a Whirlpool Nu40T61-403 water heater from Lowes that I installed due to us not being able to afford a plumber. I have since become a plumber. This morning while attempting to shower I noticed that the water was lukewarm with the shower valve turned all the way to hot. I got dressed and inspected the heater. I began to diagnose the problem. Pilot was out and Gas control valve signal light was off. Lit the pilot and it appeared to be functioning normally. My first thought was the thermopile had failed but seeing the pilot stayed lit this proved to not be the case. I was extremely relieved at that point. Turned the temperature control knob to high and the burner kicked on. At first it appeared to be functioning fine. But within about 20 seconds I began to hear detonations within the sealed combustion chamber.

My Whirlpool side by side refrigerator which is not 7 years old has had more repairs than you can imagine. After paying over $1,500.00, I have had a repair service come out at least 5 times. Today, they say I need a new compressor at the tune of $850.00. This combined with my other repairs would add up to around $1,300.00. I am certainly not going to invest any more money in this refrigerator. I wouldnt recommend a Whirlpool Gold for anything. Dont know which brand I am going to purchase now as they certainly dont make anything like they use to. Totally disillusioned!!!

I have Whirlpool Washing Machine bought at end of 2012. In 2014, I faced an issue where the washing machine board ics are gone. The services people came and check the replaced a board. It was cost me 6000 Rupees including the service cost. Very next year 2015, again the same issue. Board of the washing machine gone. Now I have to change the board. It seems it may cost more than previous one.I heard that these service engineers are taking the previous my board / replaced board. They are repairing it and sold it again and again so the quality of the board is question mark. As a customer I / we cannot spend money and change board every year. I just want everyone to think twice before you go to Whirlpool Washing Machine & its products. I had a same kind of poor quality issue with even water purifier too. Consequences - I have spent Rs. 10000 already, it is loss for me beside the buying cost of the products.

They will not honor the extended warranty on their fridge which Ive had for less than three years which will not defrost making me lose thousands in spoiled food. Extended warranties are contracts and this company should be penalized and shut down for fraud.

My old dishwasher washed much better than this one. For one thing, I do not think having the silverware basket in the door is a hindrance more than anything. For one thing, the silverware does not always get clean. Even some of the dishes do not get clean. I think the engineering of the dishwasher is poor. When you pull the bottom rack out to put more dirty dishes in, it gets caught on the silverware that are in the silverware basket in the door. Makes it very difficult to get the bottom rack out or in. I have no gripe on the size of the dishwasher. I would just like it to wash the dishes and silverware clean. The appearance of the dishwasher is good but that doesnt clean the dishes. I am more than satisfied with the appearance of it. I do like the buttons being at the top of the dishwasher so that a person cannot bump them when it is running. I just think the design of it could have been much better. My other dishwasher had the silverware basket inside on the bottom rack and I really liked that and if I ever buy another dishwasher, I would make sure that it is inside the dishwasher. I dont believe that Whirlpool is the company it used to be. I have an oven that has been nothing but a problem for me and it is a self-cleaning oven but I cant even use the self-cleaning feature because it blows something in it and it doesnt get hot and clean it. Have had it fixed twice and the company that sold it to us will not even talk to us about it. Im not sure that I would buy another Whirlpool appliance of any kind again.

I purchased a water heater Model # UG1H50400TBN, Serial # 0913T400920, from Lowes in Corona, CA. 05/07/2009 for $528 plus tax. I have replaced the following parts: 02/10/2010 Thermostat Valve, 07/23/2010 Thermostat Valve (2nd time), 08/10/2010 Burner assembly, 02/10/2011 Thermocouple, 02/17/2011 Thermostat Valve (3rd time), 12/17/2014 Thermocouple (2nd time) and 03/20/2015 Burner assembly (2nd time).Today I called WHIRLPOOL Customer service (877) 817-6750 because my water heater water is warm. I told the tech support agent that the pilot light was on so we agreed that it was the thermostat valve AGAIN. He wanted $30 for overnight delivery and I refused to pay. Now I have to go out and buy this part because Whirlpool like the Banks is too big to fail and they have license to RIP-OFF the consumer without penalties. Whirlpool has all of information and they can verify everything I wrote here just by the serial number.

My fridge is over 10 years old and the compressor has not failed. I have replaced some of the bins that have cracked or been broken over the years. It is a side by side in black color and will probably replace it with another type but the same brand as long as it is economically feasible to do so.

We purchased a Whirlpool Dishwasher from the Home Depot, it was installed 3-28-2015, less than 30 days ago. On 4-21-2015 the dishwasher stopped working. I called Home Depot expecting a replacement; but we were told you have 48 hours; you need to contact Whirlpool, due to the CRAP warranty. I called Whirlpool, we were told that a TECH would need to come out and address. They came today, ** , told us that the Motor is bad. (NOTE I havent made a payment on this dishwasher). So we called Whirlpool, expecting they would replace. I spoke to ** who advised me they would not replace, only repair. I explained this is unacceptable for a new product. I demanded to speak to her Manager; Spoke to ** who said the same. I asked to speak to her manager, his name is ** , but HE DOES NOT DEAL WITH THE CONSUMERS, this is beneath his job class I was told. So NOW I have no choice but to have this Dishwasher repaired; it will take over 2 weeks to get the part. I just dont understand how this is good Customer service. It is the worst I have ever experienced.

I bought a new computerized Whirlpool Cabrio top-loading washer and matching dryer 3 years ago. Bearings wore out under warranty, it was repaired. Just outside warranty, washer has broken down twice more. I contacted Whirlpool and received a high level of indifference to my concerns that they manufacture junk, and are not willing to stand behind it. Clearly, this is a faulty issue with the machine and should be repaired then and now at their cost. Do not buy Whirlpool products people.

We purchased a Whirlpool Estate Range in 2008, with an extended warranty. We have only moved this range out 2 times since it was installed and the last time was over 2 years ago. This range worked beautifully, no issues whatsoever. Until... tonight, the oven & one burner were being used when suddenly the range started arcing, which blew a hole through the back panel on the stove where the cord hooks to it. It continued to arc and quickly fill the kitchen with black smoke until we could reach the breaker box. The Whirlpool repairman wants to charge $88 dollars just to tell us WHY it happened. After 2 years of sitting in the same spot, why? I dont want the stove repaired, I want it out of my house! I will not take the chance that this will happen again when we are not home. When asked if this was an issue with their product, the repairman answered, I have never heard of anything like this before. After reading these reviews: Such a Liar! I wouldnt believe anything Whirlpool, or their representatives told me about their products now. I just want their crap out of my house and I will never spend another one of my hard-earned dollars with them again. Too many other choices out there. I just want other buyers to Beware of Whirlpool.

We purchased a Whirlpool French Door Refrigerator in December 2016. About 3 months later the back panel was frozen preventing it to cool. We unplugged it and called customer service. They sent out a repairman, but by then it had thawed out. He told me he couldnt fix what he couldnt see, but he didnt even check it out. Two months later it did the same thing. Then he said I must have left the door open. He made me look stupid. During that year he came out 4 times until he finally changed all parts. We kept telling customer service we wanted a new one. After going back and forth with them they finally are reimbursing us, but they charged us $300.00 because we didnt want another Whirlpool product... now we found out they have the worst ratings and we certainly had a very bad experience not to mention all the food I had to throw out because of it. They did not care at all. So please do not purchase any Whirlpool products. I would not recommend that product to anyone.

I bought a brand new washer from Home Depot, Whirlpool 4.3 cu High Efficiency Top Load Washer to be exact. It hasnt even been 90 days and it started to make the loud, horrible noise so we had someone come and look at it. Apparently the transmission blew and the oil leaked all over my tile floor. I work full time and I do laundry only on the weekends and there is only two people living in the house so you can imagine we do not use it that much. I went to Home Depot first and since it was past 30 days we had to called Whirlpool direct. The customer service is horrible. I thought since the transmission blew, they would replace the entire machine since that is the brain of it. NOPE! They said to replace the entire machine and give us a new one, it would have to break 3 times. Are you kidding me? They did not offer to reimburse the tile damage or the amount of money I had to spend at the laundromat. Not to mention its been over a week and the guy still has not come out and fixed the transmission. It would not be a big deal to me if the hose broke or something simple, but imagine if you bought a BRAND NEW car and the transmission broke 60 days after you bought it. You would take it back to get a new car. The customer service line could not care less about the issue. I spent over 2 grand in appliances from Whirlpool and I will never buy their product again because of the customer service and the fact they did not want to make the situation right. I just bought the machine brand new for a reason!

Ive had trouble with my washing machine since the end of May 2011. I have had over 5 service/repair calls which still resulted with the same problem. By the way, I do have a warranty on this product (which hasnt seem to have helped at all). I have never had such poor customer service in my life as I have had from Sears and can assure you, I will never buy another product from Sears or Whirlpool considering the experience I have had. I have missed numerous days at work only to wait for a repair appointment that never happened. Needless to say, I am very disappointed and would not recommend anyone to buy from Sears or Whirlpool.

I initially purchased all new Whirlpool products as part of my new home purchase in a Pulte subdivision, June, 2011. My WP microwave failed to heat in 2012 and the replacement of the Magnetron and Inverter and service was covered under warranty (would have cost me $493.51). Sadly, the microwave again failed to heat in 2014. I was so disgusted with this second failure, I decided to live without a MW until January, 2016 when I paid for my second service call and learned, once again, I needed a replacement Magnetron and Inverter, to the tune of $400. Both servicemen told me the 2011 magnetron/ inverter mechanisms were new technology and did not last long. Again, sadly, when I contacted Whirlpool, they would not admit to their defective product line and indicated they could do nothing since I am out of warranty. It is unconscionable that a corporation is not liable for their defective products.

Bought a Whirlpool Gold model GI6SARXXF04 less than two years ago and have already had three problems. The first was a faulty main water inlet hose that dumped water all over the kitchen floor. It was still under warranty so I didnt have to pay for it. Now have two additional problems. About two months ago there was a puddle of water under the refrigerator every few days. I finally figured out it was ice build up in the bottom freezer chest that melted that caused the water leak. The second issue is that the ice maker just stopped working. It had been working great this whole time and then suddenly it just stopped making ice. I contacted Whirlpool and they will cover the repair for the defrost issue but not for the ice maker. Gee, thanks, way to backup your product. Im guessing the reason they dont backup the ice maker is that its probably the more expensive repair. Like many people here I also will never buy another Whirlpool product again, regardless of what it is. Theyve shown me that not only do they produce inferior products, they also arent interested in customer satisfaction.

Whirlpool Gold Series - I bought this dishwasher less than 2.5 years ago. The thing already broke. The motor needs to be replaced at a cost of about $250. The thing never did a good job anyway and often had to run it more than once to get dishes clean. I paid about $650 for the machine so I guess its just a throw-away appliance. Whirlpool makes complete junk. I will buy a different brand that is known to have long-lasting dishwashers. I guess you get what you pay for.

I purchased a Whirlpool Cabrio Washer WTW6200 & this yr purchased a newer dryer w/ steam capability. I wish I would have waited a couple months for a new washer that yr and purchased the one with no agitator inside! But my washer died that day & I needed one & NO ONE informed us of the changes or problems of this agitator at the time of purchase. I have had this service several times my first year and the agitator replaced I believe twice. But it still destroys clothing. I called 1 month out of warranty and even though they had been out several times the first year for the same issue, they would not help me! Yep, even after the 1st year they said to get things done I had to purchase an extended warranty even though this was a mfr issue no doubt! So, 3-4 years later I still am dealing with the very same issue over and over with NO RESOLUTION in site and $900 in the hole for this washer and I am losing money with clothing damage weekly!Even today I had two pair of jeans, $98 ea rec these terrible uniformed marks all across the legs making them unwearable! At least for where they were intended to wear them at. They are now yard jeans...yep $98 expensive yard jeans now!!! These were my good jeans which I cant afford to buy more nor replace them so I have to do without. We cant wash anything with strings such as hoodies, shirts or baby clothing with spaghetti straps or little dangle things; we have to use the laundry mat and come home & dry w/ my Cabrio steam dryer which I love. Most everything I have to use zipper net bags but even then things still can get destroyed, especially if a hole gets torn in the bag from the wings of the agitator as you will see in the below photograph. I currently have & own an expensive washer I purchased from HHGregg by Whirlpool replacing a previous whirlpool I owned for 22 years! Yep, Im wishing I had it back & put the $200 some needed to repair it! Please Whirlpool will you please do something & make this right once and for all. I dont have $900 for another washer. I just want to be able to use my washer without it destroying everything I own. I have darn photos of what this is doing and you wouldnt believe it. It took us an hour, yes an hour to untangle a top that became entangled in the flaps on the agitator. This is the worst design I have ever seen and needs to be recalled once and for all and either fixed or replaced with new machines of equal model with the agitation issues resolved or removed & with no issues or further costs to your customers! Why would you honestly believe that an agitator with wings coming off the bottom that are not attached to the bottom would serve some type of positive purpose in cleaning clothing? All it is doing is tearing them to shreds, tangling them up, doing things to hoodies which make them unrecognizable after ripping the cords so hard out of the hoodies that Ive seen them shred the material across the collar area and opening of the cording completely ruining hoodies ranging from $35-$75 a piece even after placing them in mesh bags! Why did we keep placing hoodies in the machine? Well with 4 children at times they just dont listen or get all the info as to what is going on with the machine as 3 were college kids coming home periodically & yes, to do their laundry. Look, lets talk straight. You as a company from what I have learned from appliance salesmen locally and regionally, you knew this was wrong and knew this was your last ditch effort of an agitator before you knowingly knew you were going to an agitator-less unit on your washing machines & already had one ready to go out on the floors. I know that you Whirlpool CEOs knew this unit was a bad call but chose to ignore it. You had to know it because there was no way this could have passed quality control. It had to have failed sometime in its trials showing you the issues of the wings. Unless you never did any quality control on this unit and just rushed it through? Please to the CEOs of Whirlpool, I am asking you to make this right if not for good standing of your company do it at least for families like myself who cant afford to buy another machine and are now stuck with NEW machines yet going to Laundry mats. This was to be my last washing machine I would buy hopefully. I am 54 and was not planning on buying another. How do you think this makes your company look???? Im just so tired of dealing w/ Whirlpool to only hear I have to purchase a $400 extended warranty with no guarantee that they will fix the issue. If an attorney wants to step in & believes they can help us and maybe others then Yes please help us because this is absolutely ridiculous and is a product that needs to be recalled. We are out so much money now and like I said we are to the point we cant purchase another washer. We had to purchase all new appliances as they all began going bad around the same time.

Special features eg changing HE detergent conc. ratio for auto add feature in Load and Go is impossible to find, extra rinse doesnt work. No extra spin which would be useful for bulky loads. But preset cycles work fine and machine has very low vibration a big plus.

Bought this set for its basic functions. We dont need a lot of bells and whistles. The washer is rated as a water saver but it seems to use more water than our 10-year-old model. The only issue we had was with the electronics. Even though it has few features, it one day decided to not function at all. A call to support recommended just unplugging it for a few minutes so it could reset itself. For once this seemingly crazy idea worked and the unit has been normal ever since. I recommend buying from the outlet store as a scratch and dent. This saves lots of money and if the unit is not on display, who cares about the minor dent.

If you like having to use a funnel to refill plastic water bottles, and enjoy ice splashed all over your kitchen floor then the Whirlpool Gold refrigerator is the model for you. The problem with ice is if you dont have your glass sealed up to the ice dispenser it will shoot ice out over the top of the glass, and even if you DO do that when you try to remove your glass to cut off the ice supply it continues to disperse ice everywhere. TIP: The only way to more efficiently stop ice from spraying all over your wood floor is to do this: When your glass is full of ice, simply open a door on the refrigerator. That IMMEDIATELY stops the flow of ice OR water. Works great, and its the only way to deal with this horrid design flaw in this product....

I purchased my Cabrio a little over three years ago. Within the first month, the computer board had to be replaced and the tech informed me that it was not a malfunction in the unit; rather, it was because I did not have a sock bag for my socks and panties. I replaced the board, bought a sock bag and had no problems for about 1.5 years. A little over a year ago, the un-level started. I did research and found that I needed to replace the rods and add couplers as they were not thought of when the unit was created. This worked for an entire month. Now, I am in the same position again. It takes about 6 tries per load and the amount of water I am using is increasing with each failed attempt to wash. There should be a recall on this product. I notice there are many other complaints that match my frustrations exactly.

I first want to begin by saying that we have been a Whirlpool family for years. I now own a Whirlpool microwave, hot water heater, washer/dryer, Jenn-Air stove and dishwasher. My problem now is with the Cabrio Washer purchased in 2008. I started having problems in 2011 and the same problem has raised its ugly head again. When I try to use the Clean cycle, it starts at a 60-minute cycle and goes down to a 2-minute cycle in 3 minutes without cleaning or even running water into the tub. This time, it made a terrible noise and stopped. The tub was replaced in July 2011 after having the same complaint as above. The repairman said that the mechanism on the tub to fit into the spinning cycle is made of plastic and is not holding up. Also, in March 2012, a new control board was installed. I spoke to Whirlpool Customer Service and they informed me that they did not have any other complaints about the Clean cycle and that I should call the repairman. Luckily, I purchased an extended warranty. I vote a thumbs down on the Cabrio washer.

First of all, I want to thank all of you who took the time to write all your comments. You have helped educate me in many ways. For one thing, I had no idea that Whirlpool made such bad appliances, or at least water heaters. I pretty much grew up in a Whirlpool household. But that was a long time ago. Things change. Anyway, I too bought a Whirlpool from Lowes about four years ago. It was the top of the line 50 gallon energy saver, and it has had problems staying lit for the whole time I have owned it. Because I read your comments before contacting Whirlpool (this time), I knew exactly what to expect. And that is what I got at first--someone trying to sell me parts via shipping costs. I said no to that, and a rep called and offered to replace the unit, which is exactly what Whirlpool should have done for all of you. I am writing this out of courtesy for Whirlpool. They did the right thing for me, and I truly do appreciate that. On the other hand, Lowes wants $700 to deliver and install the new unit. I live seven miles from the store. They set my other water, the Whirlpool I purchased from them, up in my garage. It is extremely easy to get to, and it is all up to code. In other words, even though they sold me a defective product and profited from both the sale and the delivery, they now want to do it all over again by charging so much for the set up. They did not even offer to prorate the new install. Of course, I will hire and pay a certified plumber to do the job, but I am very sorry to lose Lowes. I have always enjoyed shopping there. Home Depot is just across the street, and even though I have learned not to purchase a water heater, or any major appliance there either, I will go there from now on. Losing my business might not worry Lowes a whole lot, but two years ago I bought $5,000 worth of fencing from them, and God knows how much over the years. If you and I and all the thousands of other unhappy customers would stop going there, they might feel a bit sorry for doing us all so dirty. Agreed? Thanks again, you guys.

I love my Refrigerator. It is a side-by-side with ice-maker and water in the door. I have plenty of room in the refrigerator, and I really like the adjustable shelves. I would definitely purchase another Whirlpool (next time with freezer on the bottom). I love the Stainless and would probably purchase again - or depending on the kitchen maybe black.

I have owned the machine for 1yr and 6 months, bought new from reputable company. The washer always had kind of a clunk sound which the manual says is normal. Clothes would have white marks and streaks after was but disappear when dry. Clothes would seem damp, never like they were completely washed. Went to do a load last night and thats when it stopped working. Powered on, cycle selection was fine, lid locked, typical clunk noise, then nothing, no water. Paused the cycle, lock lid light flashed but didnt unlock. Machine powered off on its own and unlocked. I powered it back on after 30 minutes and it wouldnt let me change the cycle, panel selection was frozen. So I powered it off and contacted repair. They think its the water inlet? Pending repair to see for sure. This is not OK! I had an older machine from the 90s that was still working before I bought this one. So sad to have this type of product from this company.

Whirlpool Cabrio Washer - Sucks. I purchased it when I purchased my house. After having the washer for a year and a half it stopped draining and wouldnt spin. I paid $75.00 for the service call from my home warranty and thought that I was good to go for a while. But here I am a year with the same problem. I will never buy another Whirlpool again.

Whirlpool Cabrio 6600 SW2 - Somehow a coin or two (?) are under the tub. It is not a high pitched sound. Just sounds like the machine is rubbing against the tub or something when it is being used. It does an excellent job of washing and spin drying the clothes, but the noise irritates my wife, which then irritates me. I took the top piece off and can see a coin DOWN there, but cannot reach it. Must I turn the machine upside down and try to shake the coin(s) out?

I have had my machines for years, and always buy Whirlpool. So far so good, had to replace my washer and dryer approx 11 years ago and still ok no problems yet. Wish I had the money to buy one of those bigger ones someday.

Purchased washer and dryer in 2013. After several months I noticed small holes in my clothing. I called for service since my machines were still under warranty. There was nothing the repair service could do except make suggestions on water amount and settings. Which I tried with no improvement. I also contacted Whirlpool and was told I could call for service for several weeks since it was still under warranty. I asked why call for service when I was told it could not be fixed. I did have it serviced again and told it was a problem with the design. Numerous items of clothing were ruined which I showed the technician. He gave me a phone number to contact Whirlpool. They in turn said there was nothing they could do for me. I usually place items in laundry bags for delicate fabrics but for obvious reasons not all items fit in a bag. I have never had such terrible service nor experienced an appliance that operates so poorly. I am surprised there are not more complaints with this problem. Purchased from ABT because of their reputation for customer service.

My Whirlpool Dishwasher Model# DU980QPDP, just quit a few days ago after 21 1/2 years. We paid $554.04 for it back in 1995. It was the top of the line. Quiet, with 4 fold down shelves on the top rack. Silverware basket on the door. Also a separate knife basket on the door. It came with extra interchangeable door panels. When the white ones got dented we changed to the black ones. The racks are still in good condition. Never had one repair on this dishwasher, though I used it every day, sometimes twice a day. It had a 4 year warranty on the control panel and a 20 year warranty on the tub and door. We would have it repaired, but cant get the part.

I purchased the machine December of 2010 from Lowes along with the matching dryer. I also purchased an extended warranty. A year ago July the lid on the washer broke at the hinges. I contacted the warranty provider and was told that the repair would not be covered under warranty and the damage was operator error. I purchased a new lid for approx. $250. One year later the replacement lid broke in the same location. I have tried to get a response from Whirlpool no response. I contacted Parts Select and inquired about changes that should have been made to correct the lids. He was not aware of any changes but did advise that the part had a new number which he indicated probably meant a design change. I ordered a new lid just under $250. New machines have a metal frame around the glass instead of the plastic frame which keeps failing. The springs that hold the lid in the upright position are so stiff I can hardly move them by hand. I am very disappointed in Whirlpool quality and consumer support. I will not purchase any more Whirlpool products.

We purchased our Whirlpool Water Heater about 2 years ago. Three weeks after we bought it, it stopped working; the pilot light would not light. They sent a tech out to replace the thermostat and the thermocouple. Now, it has stopped working again. My husband and I have spent nearly 20 hours on the phone with the WP customer service girls and replaced nearly every part but the tank it self. We have not had hot water for over a week and are at wits end! My husband finally got them to authorize us to get a new water heater from Lowes after they told him there was nothing else they could do to help us. Ive read pages and pages of complaints from other people having this same problem. Why do they put you through all the torture if they know its not going to work? Its very frustrating! We are almost to a point of ripping out all the gas lines and going electric! Will the new one we picked up today have the same problems? Only time will tell!

I purchased an OTH microwave model #WMH1163XVQ-1 around 12/2011 from Lowe’s. Within a year, the paint started peeling inside of the microwave on the bottom. A few weeks ago, I noticed flames in the microwave and realized it wasnt my food but the microwave itself was on fire. Im glad I was close by to immediately turn it off. I hate to think what would have happened otherwise. Does anyone have any idea of what I can do about this? Would this still be under warranty? This is the first and last Whirlpool product Ill be purchasing.

My three month old $2,000 combination microwave-oven works a fine, its the just the details that stink. For example: There is no way to turn off the turntable. Yes! a crappy $40 microwave can do this, but not this one. Liquid got into the middle of the door window. You cant open it up to clean, they want to send a technician to clean that up so you can actually see through the window. How much? $150. How was it possible that Whirlpool did not adequately seal the glass? They dont care, and dont care about how it looks.

This dishwasher is noisy, it does not get the dishes clean, and anything that is remotely lightweight gets thrown all over. This must be one of Whirlpools cheapest models as I have had other Whirlpool products and they were fine.

I bought a brand new Whirlpool washer and dryer. The Whirlpool Cabrio washer does not clean my clothes no matter what size load you have. I have tried every combination possible to get my clothes clean and 95% of the time there are clothes that don’t even get wet let alone clean! I have only owned this washer since July 22, 2018 and am now willing to give it away - that’s how upset and displeased I am with it! If you read reviews, stay away from this model - not good!

I have been using Whirlpool products for quite sometime. I had bought a 3 door refrigerator (Protton) about 2 years back. However I am noticing that of late, the vegetable drawer does not cool to the appropriate temperature. The vegetables as a result are spoilt. I am unable to understand what to do. I have checked with the other temperature settings and they are all in the normal mode.

I used the Whirlpool website contact form, and described an issue I have with the Cabrio washing machine. When the form is submitted, it states that the company will respond in three business days. Two weeks later, after no response, I submitted a second contact form. It has been five days, and I still have not received a response.

My Whirlpool side-by-side refrigerator is just 4 years old. When they delivered it, they noticed damage on the bottom which required them to bring me a new refrigerator. The new one had issues with the ice maker that required multiple service calls to fix. The refrigerator door always seemed a bit misaligned as it was a bit lower than the freezer door, but it closed, so I never complained. I was just tired of all the issues! During the last six months, the door started to remain ajar instead of closing completely so that we had to always be sure to apply sufficient pressure to close it tightly. I considered calling in a repair, but it was still closing so I thought I might be overly critical. As it got worse, I realized the door was defective, but one day, it just fell off completely without warning as though the hinges were made of butter!After multiple service calls, a tech reattached the door, but I could see that it would not hold and sure enough, it is starting to remain ajar again. I have contacted the warranty company who is now saying the service tech claimed we were hanging on the door. This repair company the warranty company uses has an F rating with the BBB. Now, Im being told it may take a couple weeks to get another repair company to give them an opinion, but the issue is clear, the door was defective and it looks like they found a way to avoid having to make good on the warranty!

This is my second water heater in three years. The problem is the thermocouple thermostat. Also, when I drain the water, it comes out of the heater black because of the corrosion in side. I spoke to people in the company, and they were nasty to me. This happened to my two heaters in 2 1/2 years. Please, do not buy a Whirlpool heater.

In 2008, we purchased a Whirlpool Gas Water Heater from Lowes. Three years later the tank started leaking (this water heater had a 6-year warranty). Per Whirlpools instructions we were to return this one to Lowes for a refund (in hindsight we should have taken the money & went elsewhere to purchase a better brand!). As our plumber was removing the leaking heater we went to Lowes to purchase a new Whirlpool Water Heater upgrading to one with a 12-year warranty hoping that this one would last, it was advertised as the BEST one Lowes sells! After our plumber swapped out the heaters we returned the leaking water heater for our refund (remember this one had a 6-year warranty & only lasted 3 years).This past June (2015) our water heater stopped working, turns out the thermocouple went out which shuts the gas valve off. Called 5 plumbing companies in the Metro Phoenix area, not a single one would work on it! We researched the repair, called Whirlpool & was told that this water heater was out of warranty. Wait a minute! This one has a 12-year warranty & it is only 4 years old! Whirlpool told me that it is a replacement water heater so the warranty for this water heater is only 6 years (from the 2008 date of the purchase of the first water heater). It didnt matter that the replacement water heater was a different model & was more expensive than what was refunded to us. We replaced the thermocouple ourselves & got it going again. Last week it started leaking, called Whirlpool again got the runaround again, called a plumber who replaced it with a new Ruud for $1000.00 (Water heater + Labor).We went back to Lowes to try to get their help resolving this, the store manager said this was a Whirlpool warranty issue. We ended up taking the junk Whirlpool water heater to a recycling facility and getting $2.50 for it. Bottom LINE!! READ THE REVIEWS, THEY ARE TRUE!!! There was a class action lawsuit with a settlement of which I never received a notice for, I read about it online this summer, but it was too late to opt in. Dont waste your money on Whirlpool water heaters, no one will repair them, Lowes wont stand behind the products on their shelves, they get your money & hide behind the manufacturer & Whirlpool has very nice script to get you off of phone! Whirlpool used to be a trusted brand (do your research, I think they are the manufacturer for certain store brands! ). Our new Ruud water heater has a faster recovery than either of the Whirlpools that weve had; the drain valve is brass, not plastic like the whirlpool, it is overall a much higher quality.

I purchased the Whirlpool washer with the expectation of having at least clean clothes. In fairness, I do wash some pet items but they are done separately. My clothes at time come out dry in spots because theyve not been touched with water. Forget the balancing issue. What I will have to do is wash, rinse, and repeat. This will be my life until I can get a new washer. Never again Whirlpool.

Purchased a new Whirlpool washer and dryer at Best Buy 6 months ago. We complained to Best Buy and Whirlpool about our clothes not getting cleaned. In other words, my clothes are coming out of the washer dirty. My make-up towels come out with make-up, my husband’s fishing clothes smells like fish and my son’s bike riding clothes is full of dirt. Whirlpool’s answer was the technician is reporting that the machine is working fine. Whirlpool told me to use different cycles and detergent etc. and I have done everything they ask, but my clothes are still the same. I told them this is a defected item. A washer should do its job - wash dirt and smells out. I want a different washer and they refuse to exchange this item for another washer after a second call to technician. Best Buy is telling us there nothing they can do for us. What has America come to? The manufacturers and dealers are selling to consumers and taking advantage of them by not responding to the needs of the consumer. In other words, we the consumers pay for product, take time from work and personal time to reports these problems and we get nothing back, just the run around. Is there something we can do? What can we do? This is very frustrating. We work for what we need. We pay for what we need and we dont get what we need. On the other hand, the manufacturer and dealer get what they need, our hard working money. What can we, the consumer, do to get our hard working money worth????? If anyone knows, please share your experience.

I have used Whirlpool products for over 30 yrs. This is the worst made product I have ever purchased. The ice maker doesnt produce very much ice. The cold water on door isnt cold. There is too much wasted space in freezer and refrig. side. You cannot get anyone to call you back to call for help. I contacted Whirlpool over a month ago. No return call yet. Consumers beware!! Model no. WSF26C3EXF01.

Do not ever buy a Whirlpool refrigerator. Sloppy construction, bins dont close, doors dont seal well and a brand new fridge doesnt cool to a safe food zone. When we call for service, I got the run around for almost 2 hours. They wont be sending anyone to service a brand new unit for an entire week... And thats 2 days before Thanksgiving! I have never had an appliance made this poorly. We dont have the space for a bigger unit, so thats why we bought this model. Size shouldnt impact quality!

We purchased the Whirlpool Gold Series smooth top stove from Lowes in December of 2013. The stove is not even 2 years old and it doesnt work. Last September, I noticed a few times that while baking food in the oven, it was burnt after only 10 minutes, due to a runaway temperature. After that, the oven wouldnt heat up properly, it would take too long to bake anything because the temperature wouldnt reach the reading on the display. Then it just stopped baking or broiling all together with the error Feature unavailable. Weve had a serviceman out at least 3 times. Of course, the warrantys run out and its cost us close to $500 to keep fixing it, and two motherboards and a bottom element later, its still not fixed. They wanted to order 2 more parts at our expense, but we cant continue trying to fix this lemon. I will be shopping for another oven, and will never recommend Whirlpool to anyone.

Two years ago, we purchased a Whirlpool Cabrio Washing Machine from Sears. All of a sudden, it was making sounds in the spin cycle that sounded like a jet airplane taking off. It was terribly loud. We called repair technician, which cost $90, only to find out that the bearing is gone and its going to cost over $500 to fix it. This is absolutely ridiculous! We expected it to last several years, only to find out that we would have to spend almost as much as the washer originally cost in order to fix it. We paid $700 for this machine, two years ago, and I can say that Ive never been more disappointed with a product in my life. My previous washer lasted thirteen years, not to mention my dryer and stove fifteen years, with minimal repairs. I will never buy another Whirlpool appliance again. I have read some other complaints on this consumer affairs website, as well as other sites, regarding this same washer with the same problem on the bearing and cost to repair. If anything, I think Whirlpool should make good on this product and offer something regarding a recall or payment for repair in some form. As far as Im concerned, I will alert everyone I know about Whirlpool appliances and advise them not to purchase it. Now, I either have to pay over $500 to repair my washer or go buy another one. I do not even want this Whirlpool appliance in my house when I can get a washer for cheaper than the cost to repair it.

In the past 8 years, I have had to replace 2 Whirlpool Calypso washing machines and 1 Cabrio washing machine. All 3 washing machines worked great for the first 2 years. I purchased the Whirlpool extended warranty on all 3 washers. The first Calypso had 12 repairs done on it. Finally A&E repair service deemed the washer not repairable. Whirlpool replaced the Calypso with a new Calypso. Based on the problems with the first one, I again, purchased the extended warranty. Again, after the manufacturers warranty expired, I again had issues. After numerous repairs, A&E deemed the washer unrepairable. I contacted Whirpool warranty service and was told that they would reimburse me 75% of the cost of their choice of a Whirlpool washer! Since I have had 10 hand surgeries, I need a washer that does not have an agitator (hence the original Calypso purchase). The model that Whirpool warranty deemed as a replacement had an agitator and was also a much lower energy efficiency rating. I found that the Cabrio was a comparable replacement model and finally Whirlpool agreed to replace the washer at 75%. I was angry that they didnt cover the total replacement, but felt at least I got a totally new problem-free washer. I again purchased the extended warranty. I got the Cabrio in March of 2008. In April of 2011, the washer started getting rust around the bleach dispenser and also I would get UL code (Uneven Load). A&E tech came out and replaced a bearing. He said that the rust was not covered under the warranty. I asked how it was okay to have rust around the bleach dispenser if the washing machine is always wet with water. A month later, I was still having a UL code and the rust was getting worse. A&E came out again and said that even though I saw rust around the bleach dispenser, the rust was in fact underneath the tub and had eaten away at the parts. He called the warranty company to authorize repairs and the Whirlpool warranty company denied any more repairs on the washing machine.

Very dependable. We loved all of our appliances in the past as well as in the present. It has been a go to for us especially with bad experiences with other brands like OG and GE. We have gotten a washer and a good dryer and have worked. No complaints whatsoever.

I have a 3 1/2 year old 9400WFW WP washer with a 70 error code. After viewing complaints on various websites, it appears this is a large scale problem with Whirlpool Duet owners. I just got off the phone with WP customer service and explained how many complaints are out there for F70 code error, yet they do not have a recall on this part!How can this be justified? This is a non-mechanical part of the washing machine. The life expectancy should be more than 3 years.My washer is not overused as there are only 2 people in the household. I do not want to pay the cost to repair this. I think WP should issue a part recall on this model. Does anyone know how to find out how many replacement CCU or CPUs have been purchased in relation to the number of 9400 WFW sold or if there may be a chance that WP needs to reconsider a recall?

Beware to those who are in the market for a new washing machine. I am reviewing the product not the retailer. The lack of the agitator on the machine has left the consumer very agitated! I have called Whirlpool in the first year at least three times for them to come look at it and see the pictures of the clothes. It rips but the response basically is, “It cant be helped maam.” Here is what it does: When you do a load of shirts the sleeves tangle so much your clothes rip You can do approximately 3- towels or it won’t spin correctly. A load takes forever! Now I have been doing laundry for over 40 years so I know how to do a load and I have never been so disappointed in a product I could not return, why you ask because they say there is nothing wrong with the machine. Dont do it! So Whirlpool get a 0 star rating from me but I have to give it one for this review to move forward.

I have a rental home and my residence, I have purchased a fridge for BOTH places. Within 1.5 years, both of the fridges shelving cracked. Customer service will not do anything to remedy this. It is a known issue with his model of appliance. There are numerous complaints and they DO NOT stand behind heir product. NEVER BUY WHIRLPOOL.

Our ice maker was not producing ice. Whirlpool Warranty sent a co. Kens Appliance Services to our home. The repairman diagnosed freon leak. When he came back on Oct. 7 with parts he blowtorched the electronic board & wires while fridge was plugged in. We still dont have refrigerator weeks later. We are buying food & ice every day. The next co. they sent werent licensed to add freon. He verified burnt board. Third company they sent told Whirlpool warranty to replace our fridge. They tried to sell our warranty back instead.

I purchased a Cabrio high efficiency washer in 2011 and have had the glass top lid crack twice. The hinge is rusted, shedding rust all over the corner of the washer. It is a design flaw, for I see others have had the same problem with this particular year. I have also looked at the newer versions of the Cabrio and the lids have been redesigned. This lid should be recalled and replaced with a newer version, because this lid will always rust and crack with use.

My Cabrio washer worked fine for approx 3 years. Within the last 9 mos there has been one repair/replacement issue after the other: pump, computer board, bearings, seal, etc. Whirlpool takes no responsibility. Worse purchase I ever made.

July 2017 I purchased a Whirlpool refrigerator Model # WRF757SDEM00 S/NK51709722. The refrigerator portion went out, the repairman said it was the fan therefore I spent 351.00 dollars for house call and fan. When that did not work the repairman spoke to whirlpool and they said the panel of small computer may go out with it 212.00 plus tax. Did not allow that and tried another repairman who said the value that switches from freezer to refrigerator was out and if I could find someone to fix it would cost between 600 and 800. I went out and bought a Samsung because on the front said 10 year warranty. At least anything is better than 1 year whirlpool offers. There is NOTHING in the name.

My wife and I purchased a Cabrio washing machine and dryer, this is by far the worst washing machine we’ve ever owned. It hardly fills, even in deep water cycle. If you watch the clothes through the smoked glass lid with a flashlight, you can see they don’t even go underwater. The dryer seems to be fine but I would never recommend the washing machine to anybody looking to buy one.

I’ve had my washer and dryer for a long time and it has been okay and it’s time to update. It has had its up and down and I may get another just after a while they are outdated and better appliances come along. Smarter people are making smarter things.

When we bought our side by side fridge (model GD5RVAXVB02), the manual said to clean the condenser coils if you have excess dust and/or pet hair. We have both. We tried with the vacuum and with a brush but it is impossible to get to the coils because they run side to side instead of front to back. You can only get to the first coil in front. The rest cant be accessed from the front, sides or back. I called to find out how Whirlpool recommended they be cleaned and they could only recommend a vacuum attachment tool (8171579A) to clean the floor below the coils or a coil brush (4210463RW) that cant reach the coils! This design is meant to fail prematurely. They could have easily installed the coils running front to back so they could all be easily cleaned.

My Whirlpool dishwasher is not old. It has hardly been used, and the board is bad. My washing machine, a duet, is not old, and the knob to turn it on broke. I am returning the knob to Whirlpool. Perhaps they can duct tape it and make it work on another machine and make big dollars on someone else that buys their junk. This is the LAST piece of junk that I will ever buy with a Whirpool name on it.

We purchased a Cabrio top loading washer (WTW6400SW2) and a Cabrio dryer (WGD6200SW1) in 2007. From day one the washer has tied clothes in knots, never cleaned the clothes properly, and sputters the detergent and bleach unevenly. The fabric softener dispenser clogs up too, rendering it useless. The knotting of the clothes leaves them so tightly wrinkled they come out of the dryer very wrinkled. The water level, determined by the washers self-sensor that weighs each load, does not fully submerge the clothes. The manual says this is normal operation for this model and that it will not affect the cleaning process. Wrong. The small agitator is insufficient to clean the clothes but does a wonderful job of twisting them in long, tight knots. I want to kick myself every time I walk past the washer for paying so much money for such a poorly designed washer. I was very sick when they were first delivered and wasnt able to do much laundry. By the time I was well enough to do more with it, I noticed the clothes werent getting clean and were actually being damaged by the washers process thanks to uneven detergent distribution/spotting from the clothes sitting above the water level, and being poorly agitated and rinsed. Before I knew it, my warranty had expired. It was a very hectic year. Ive been very sick. We purchased it from Lowe’s. I had their techs out a time or two to check it in the beginning, but they always smoothed it over with some waffy, generic explanation. Eventually, I was past my 30-day trial period. I was on my own with Whirlpool, whod refer me to the manual and make me feel like I just had to get used to the new technology of the self-sensoring washer. Ive read that Whirlpool is aware of this issue and doing nothing. Ive read other complaints that describe the same problems I have and its obvious this is a design flaw. I appreciate these posts because I least I dont feel like Im insane anymore. No, just horribly ripped off by Whirlpool.

I purchased this machine in April 2011. Adequate performance until this past fall. It did not drain properly and began to smell, then stopped working. I called a local certified repairman who discovered an item of clothing trapped beneath the basket blocking the drain pump. $109.00. Less than 2 months later it happened again. The repairman returned and again found a blocked drive shaft under the basket. $109.00. When it happened a third time I called the Whirlpool repair line. A serviceman was sent out and immediately knew what the problem was (prior experience). He removed the basket and once again there was an article of clothing under the basket, blocking the drain pump - $129.00. At this moment it is beginning to smell again. I spent 40 minutes on the phone this morning with Sears and Whirlpool. No help whatsoever. This machine is not even 3 years old. I never overload it and clean it regularly. I bought the washer and dryer as a set because they are quite visible in my home. I have had Whirlpool products for over 40 years and never had a problem. I need someone to stand behind this machine.

I purchased top load washer and dryer from Lowes last week. When I was washing clothes the first time 12/4/18 (the day Lowes delivered) I washed in quick wash setting, machine was showing me all stages of the wash on the progress lights. It took about one hour for one load. Today 12/11/18 I spoke to your customer service associates Trina regarding the issue with my top load washer wed4815ew1 serial m82572023. I was told a technician is schedule for repair tomorrow. I try to quick wash two loads, washer progress light only went to wash mode only. I had to press start/pause, select drain and spin to remove excess water. I started 8:30 am and finish around 1 pm. I was waiting for the cycle to finish, twice all progress stages light went blank. I have no idea when it will be done. Machine made noise, not spinning, no water in it. The dryer wtw4816fw2 serial c84621285, I dry at energy prefer setting, when the clothes was dry, dryer continue without the buzzing signal to stop. I had to keep watch of the time and turn it off manually so it not energy efficient when I have to monitor when clothes will be dry.

I purchased a new Whirlpool Cabrio washer 3 years ago. It is the worst washer I have ever owned. During the first year it had to be repaired. It continuously flashes F51 when I try to wash a load of towels or bedding. I am beyond fed up with this machine and will NEVER purchase another Whirlpool product. If you are considering purchasing one of these I would tell you not to waste your money.

This is about my Whirlpool Cabrio top load washer machine (model number WTW6200SWD, serial # CT3670597). I bought this machine in 2007, and soon after, I was having problems with the F1 code. After several trips back and forth to reset the code, so I can get the laundry done, and many frustrations, it was time to call Whirlpool to resolve the problem. I find out that there was a recall for this ongoing issue. They sent a technician to replace the mother board, and everything was fine for some time. Soon after, the machine was giving us more problems with the F1 code, and the UL code. It doesnt matter which way I try to balance the load. This piece of junk will not work. Whirlpool needs to stand behind this issue, and recall this washing machine for good. Every customer should be entitled to a full refund, and a compensation for the many hours of electricity, aggravation, and frustration, wasted trying to get this junk to work.

Ive owned my Whirlpool appliances for almost a year. So far Ive had 4 maintenance calls for my dishwasher to be fixed (over and over) and once for my refrigerator. Yes, its currently under warranty, but Im afraid to keep it without an extended warranty due to all the issues Ive had with them. So, now Im going to be spending hundreds on an extended warranty. I will never buy another Whirlpool.

This thing will not bake correctly, leaves pie bottoms raw, yes we use convection. We have tried everything to get it to bake correctly but to no avail. Top and control panel get very hot when only using oven. This thing is junk, taking it back to Lowes.

I purchased a Whirlpool Cabrio and a one year extended warranty two years ago. As soon as my warranty ended, my washer started to malfunction. I recently started to receive the F-51 code and the washer shuts down at the spin cycle. I am angry because I spent just under 1200 dollars on a washer a little bit over two years ago and now, it is sitting in my laundry room taking up space. When I called Whirlpool, they told me I could purchase another repair warranty for $316.94, which would take the cost over 1500 dollars for this washer and there was no empathy nor compassion for what I was feeling as a consumer from the customer service rep. I spent my hard-earned money on major appliance purchase and I think that it is only fair that I get more than a two year usage out of machine that was designed to last at least six years according to their website. There is no way that this should just be my lost and cost me additional funds.

We relied on consumer reports as the primary source for a recommendation on this washer. Just under two years old, it started making a noise, which suddenly went away. Then one day the machine would not spin and drain, and we could not decipher the error code into anything useful. I turned the machine over to find that the drive belt was half-on/half off the pulley on the drive motor. This caused the belt to ride against the belt guard and wear right through it. I removed the belt and determined that the cause of the problem was that the large pulley on the drum was loose. For some reason the nut which holds that pulley on was slightly loose, causing the pulley to wobble. Not sure why they didnt use some Loctite on that nut. I put everything back together and tightened the nut. No problems and I checked it a month later, everything was still good. Fast forward to last week, when the machine was not yet 3 years old. Same thing, washer would not spin and drain. Tipped machine over to find that the belt had fallen off, the drum pulley was again loose. But this time the belt had damaged the pulley on the motor. I figured, no problem, just order a new pulley. Well you can buy just the pulley on the drum, but the pulley on the motor is part of the motor, it cannot be ordered by itself. The cheapest I could find the motor online was $250. We decided to cut our losses and buy a new machine. We will NEVER buy another Whirlpool appliance (or anyone elses by the same manufacturer, i.e. Maytag). Our last Kenmore washer lasted 23 years. Oh but it had an agitator and wasnt listed as HE (High Efficiency), so I suppose the environmentalists would get the dry heaves thinking about the impact of that washer on the environment. But it was useful for 23 years. Now this High Efficiency Whirlpool is headed for the recycling pile. Sorry, I think this hurts the environment more than an appliance which just works year after year. Yep, they took a design that worked and now we have energy/water efficient washers that dont last very long and are so expensive to repair that the solution is to just buy a new one.

Bought microwave two years ago, almost immediately when stove area got warm, the microwave would not work properly. It would beep, the info keypad would cycle, then freeze up. After unplugging and letting it sit for a while, it would work fine for a time. Now it doesnt work properly at all. We keep it unplugged until we need it then it may or may not work. I have had a service company look at it and the only thing they could figure was that was an electronic failure from the heat. I am concerned that it is a fire hazard and leave it unplugged. Not what I expected from a $1000 appliance. I wish there was a class action suit that I could join.

I am in construction and have had to deal with failed motherboards on new Whirlpool fridges that we put in some rental properties. Knowing that, when I went to buy a fridge for my own house, I went to a very reputable appliance company and talked openly about getting a fridge that wasnt going to be a problem. My sales agent and I go back always and he was very open about the problems with the more gadgeted Whirlpools so we picked a low bells and whistles French door fridge to avoid that. It stopped cooling at about the same age as all the rental units did and had a control panel fail. The sales guy and I laughed about how even knowing about the issues I didnt avoid it. Their company came out and fixed it for just short of 300 bucks.Two months later, it stopped cooling again. The service tech came out and this time hit the side of the fridge with his hand and opened a relay getting it to work, at least for another week. The tech told his boss that I must not have shut the freezer causing it to go into defrost mode. The third time it failed, we were out of town and lost all our perishables. We had the same tech come out and replace the board he got to work the last time with a whack to the side of the unit. That board should have been under a parts warranty for 90 days but I may have missed that with the slap repair working for the additional 2 weeks.Im trying to put this behind me but Whirlpool sent me an Extended Warranty Plan opportunity. I can now buy a plan on an almost 3-year old fridge. I am wondering if they are trying to give me the hook up on a bad product or just hoping to prey off my fears and cash in. The company I bought the appliance from has been first rate but their hands are tied by Whirlpool who has virtually no support for their vendors. Before buying a Whirlpool, consider a Sub-Zero. After you figure in the repairs, they arent too far apart in price.

Our Neptune washing machine is 15 yrs. old. Minimal problems, which I could fix myself. The door gasket needs constant attention to prevent mold. It is a front loader. I have replaced the gasket once. The belt transiently slips.

Purchased a Whirlpool refrigerator the last week of January 2014 with promised delivery date of February 6, 2015. Received call Feb. 2 that the earliest they could deliver would be February 13th. Received call Feb. 3 that the earliest they could deliver would be February 19, almost 2 months after purchase of refrigerator. Sears, where we purchased the refrigerator, told me that they have been dealing with this for 10 years with Whirlpool. Why would Sears sell products to their customers with this kind of delivery problem? They only communicate with Whirlpool via email, so there is no resolution with a person to get issue taken care of. We will never buy a Whirlpool product again & will never buy anything from Sears again.

I purchased the Whirlpool touchscreen gas convection range and I do not recommend this product at all. The oven cannot operate without using the touchscreen to set the temperature and it has a mind of its own. Woke up in the middle of the night and the oven turned itself on to 550 broil. I called Whirlpool, they sent a tech out who replaced the touchscreen and the same problem is happening. Not engineered very well. The range would have been fine without the touchscreen, if only it had an old fashioned knob to set the temp. I do not recommend buying this appliance.

This is the worst washer Ive ever owned. It consistently gets off balance, doesnt clean the clothes, and is a perfect example of poor design. I have owned the washer for approximately 9 months, and hate it. Im getting rid of it as soon as possible.

I’m disappointed in this dishwasher, it’s not yet a year old, and it doesn’t clean the dishes, and it also does not dry them. I now wash and dry my dishes by hand, the machine stays soaking wet even two weeks after running it.

I bought a Whirlpool Cabrio Top Load washing machine September of 2012. It has never cleaned the clothes well. For the last month the machine has a very loud spin cycle. I am very unhappy with this purchase and it is 2 months out of warranty. I emailed WHIRLPOOL and was told that all appliances have problems and wear out. WOW! It is 14 months old and has been used with care. I will never buy another Whirlpool product.

I have a Cabrio washer displaying the F-1 error code. I called on Thursday, the 15th of Sept. I spoke to Vicky in the Cleveland, TN division. She told me that the F-1 code on my machine (model no. WTW6600SW2 and serial no. **) was covered under a recall at no cost, parts or labor (I specifically asked this question). She set up a service repair ticket with Freds Appliance at 888-453-7337 and gave me the date. I was home waiting when they called. The driver drove in the drive and asked if he was there for my Jenn-Air cook top! I said no, the F-1 error code on the washer. He explained that he had just used the last control board last week and he changes them frequently. I called Whirlpool. A very snotty Ashley proceeded to tell me that nothing was covered and I would have to pay. I asked for a supervisor and Ratna answered after a hold of 45 minutes on my cell. I explained the situation. After begging, she proceeded to tell me that she would pay for parts only. I explained that the tech did not have the parts, didnt even know the correct appliance, and now I have to take another day off work to meet him to have my washer fixed. I have not used the washer in two weeks. I used to only buy Whirlpool products. After reading all the complaints about the same error code from other consumers, I believe there are enough complaints that we as consumers should be protected.

My NEW Machine Top loader HUGE drum. Have problems with clothes not looking like they’ve even been washed, Spun so hard they are twisted all to heck. And white stuff - my oxy powder maybe? Not dissolved. My old machine was a Kenmore 30 yrs old. Thought I’d be able to trust whirlpool but not sure. Am I missing something in the loading process. Seems to read something bout not Covering the knob on the bottom. Is this true?

I am very happy with this dishwasher. It is not a high end, rather middle of the road, but is very quiet, does a great job of cleaning my dishes and pots and pans.

Do not under any circumstance end up with the Whirlpool fabric washer and or dryer in your dwelling to wash and dry your clothes. The washer, model # WTW7000DW0 and dryer, model # WED7000DW0. I am so upset with these units and the company I bought a 5 year extended warranty thru. I cannot put down in words what I think, because this review would not be published. Do not even accept these units, even if they are free. Even the repairmen who have been here said they would not buy these Whirlpool junk washer and or dryer series. They acknowledged the problem and said nothing could be done even though there is a legitimate problem. Not only is there a problem with the washer, the dryer as well has serious issues. All washes have to be put on the deep water cycle and some loads have totally dry spots on clothes where the clothes did not even get wet after the washer went thru the complete cycle. Also, get this, this washing machine even has to be cleaned itself with a cleaning tablet run thru a cleaning cycle. What happens are the clothes get a nasty, slimy, white muck on them. Even, immediately after the washer gets cleaned, sometimes the clothes 32nd up with this muck on them again. If you do not see this muck on your clothes before putting in the junk dryer, then the clothes have to be washed and dried again. This washer is supposed to be efficient, not a chance. It gets costly having to purchase the cleaning tablets and the washer(28th only two people in the household) has to be cleaned a lot more than what the manufacturer says and I called and asked. Pure junk, do yourself and even your enemies a favor, stay away at any cost, and like I said, even if they are free.

Purchased range 10-26-12. Had 3 service calls first year. 1st time, it started. When service guy came a few months later, same problem. A new igniter was installed. 3rd time, another igniter was installed. My year warranty had run out but still had same problem. Asked for a new range, was rejected. Im afraid if burner is lit, had we try to start oven we are going to have explosion.

I want to make this clear I’d give NO stars if I could!! Whirlpool is totally junk!! I bought a whole suite of Whirlpool kitchen appliances from Home Depot that is a dishwasher, stove, and fridge. The dishwasher never cleaned the dishes, always left a film on everything, cant clean out the drain area, the screens don’t come off and less a year later the dishwasher top rack literally fell off and broke all the glasses that were loaded in it and the fridge keeps freezing all my food!!! I keep having to adjust the thermostat up down up down just to make it doesn’t freeze. Now that the warranty is no good on any of the crap I will no doubt be charged an arm and a leg to get it fixed, which definitely won’t be worth it!!! Whirlpool is such crap!!! Made in America no wonder!!! Don’t buy any whirlpool anything!!! You will be very VERY disappointed!!! I’ve bought plenty of brand new appliances. Bosch is by far the best dishwasher even the cheaper ones. Now I have to pay to dispose the whirlpool crap!!! I am sure whirlpool doesn’t give a crap though!!! They will keep selling their crap, but don’t Buy it!!! You will be soooo disappointed!!!

Dishwasher is 15 years old and still going strong. Minor leak which disappeared when I cleaned the gasket. Good internal arrangement for fitting dishes & silverware. One of the best appliances I ever got!

I purchased a brand new fridge in July of 2014 (model wrf990slam00) hoping refrigeration repairs were now behind me. They were not. The ice machine did not work from day one and they knew it was defective when I called so they had someone come out to replace it. Just over a year later it is not working again and my freezer will not freeze either. They tell me I am now out of warranty and any repairs going forward will be out of pocket. Congratulations Whirlpool. You make products that last a whole year. Do not buy Whirlpool. They could care less about you or the quality of their products.

I love the French doors with the ease of seeing everything when you open the doors. The only thing I do not like about this unit is the ice maker. If there is more than one person in the household there is never enough ice. Also the ice gets hung up inside the ice maker often.

I have had trouble with this AccuBake stove since four months after I bought it in 2011. First, the clean cycle would work intermittently then would not ignite to bake, broil warm or clean. All burners would light intermittently. Every time I had trouble, I called the service tech from Homestead Lumber, where I purchased the product from and he could never find anything wrong. Product would work fine whenever he came out. Finally, it acted up in May of this year while the product was still under warranty and while the service tech was here. The tech replaced the circuit board. One month later, Im still having trouble replacing igniter. Four days ago, Im still having trouble. This stove stinks. Right now, I wish I had my $959 back for the stove and wish Whirlpool had it stuck up their butt.

This is the worst washer ever. I purchased this washer (Whirlpool Cabrio Washer Top load) brand new in the box thinking it was a great price and a good deal. Worst choice ever. I have been so disappointed in this product. It is very noisy which is something I have learned to live with. It doesnt even get simple stains out. I have tried every load combination and change detergents and stain remover a couple of times. Most time I have to soak stains again and again and then wash several times and most times it simply doesnt clean clothes. It leaves detergent residue on dark clothes so of course I end up washing those again as well. The towels and sheets turn into mushrooms in the bottom of washer.

Purchased 2 years ago from Lowes with the matching dryer. This machine (Model #WTW8540BW0) has more problems than the Bosch front load that I replaced. All of my white clothing gets small rust colored lines on it. I am sure this is because the top of the bleach dispenser is lined with rust. I have never owned a washer that rusts (screws are also rusty). I will NEVER purchase another Whirlpool product.

Absolute garbage!!! French door refrig/bottom freezer. Too much to go into. This is by far the worst product that I have EVER purchased in my life. If I was strong enough to lift this piece of ** over my head I would carry it into the corporate headquarters of these money grabbing dirt balls and throw it through the CEOs door. Amend that: I would locate customer service and consider them bowling pins. What a bummer; how far we have fallen!!!

We bought a Whirlpool dishwasher and microwave from a reputable appliance store. The dishwasher top basket broke within 30 days. The microwave lost 100% power within 30 days. Both under warranty but parts had to be ordered. Couldnt use either appliance for over a month. What is going on Whirlpool? We need a refrigerator, but I no longer trust your brand. I dont want it to quit and then lose all of our food! Please get it together and make quality products again.

Purchased in January of 2014: Brand new Whirlpool WOS51EC7AS01 model oven - interior bottom metal has buckled causing the enamel to crack and break off from oven bottom. I registered all my new appliances immediately for warranty. When this happened after the fourth or fifth time baking in the oven, I called Whirlpool to get a service person to look at it. First person Whirlpool scheduled to come out refused to even come out, without looking at my oven. He said he knew we did something wrong? They immediately set up a second service person, after two weeks waiting for an answer; I had to call him (twice). He said that his report and pictures sent into Whirlpool shows normal use and there is nothing wrong with our oven? So, Whirlpool will do nothing to repair the oven? We just spent almost $4,000.00 on all new Whirlpool appliances, and this is how we get treated? WOW! Never again will I ever purchase a Whirlpool product. The enamel is gone in spots from our oven floor. How long do they think that will last with no protective coating on the oven? Terrible customer service.