I updated appliances in new house, but didnt realize the builder would choose the smaller side by side frigidaire. Could use a larger freezer space, also would like a ice maker that cut off when bucket is full. Overall I love Whirlpool appliances.

I purchased this machine in February 2019. The standard one-year warranty covered the first service call less than one year later. This call was related to the main control board. If this part goes out it will prevent the washer from advancing through the cycles. A technician was able correct this problem by resetting control board. That was sometime the first year. The next call was for the same problem and it cost me $90 to have a technician reset the board again. I then learned how to do it myself through online research. However, I had to do it more regularly and this got old as you can imagine. I did buy myself about two months of time by purchasing a used part but it soon failed as well. This main control board cost $564 if you get it from the manufacturer. This exceeds the cost of the machine. It was purchased in 2019. (The same machine has gone up to $740 today.) I had no other problems with that appliance however, it appears nowadays with electronics taking over cycles vs. mechanical parts you will not enjoy the same longevity as I did when I got 16 years out of a GE washer before this one. I have replaced this machine with a competitors product that costs less than the part except for the 5-year warranty from Lowes.

The duet washer is just over one year old and started showing F25 code on screen. It had been making a really loud noise in the spin cycle. Last week, a really loud noise and then the loads wouldnt be spun. There was a puddle of water on the floor near the machine. We had a repairman out today and he stated that theyre repairing these machines all the time. He stated it was the bearing and that theyd been told that Whirlpool had installed bad bearing from a different supplier. I called the Whirlpool experience and after 4 minutes and 19 seconds, I actually spoke with a service rep. She said since my machine is less than one month over the one year warranty, Id have to call the extended warranty people. I asked for a supervisor and after 2 minutes and 38 seconds, she came in line and wouldnt budge from her story. They also stated that there are no service issues with this model washer. Extremely poor attitude and Whirlpool is doing everyone, whoever purchased a duet washer, a terrible job on these washers. At least, Ive now found out that there are a lot of other folks out there with the same problem. We need to get some attorneys to start a class action just like the mold/smell customers did already. Sad, sad day for Whirlpool as Id been a customer all my life.

I purchased an expensive dishwasher made by Whirlpool and sold at Lowe’s. Immediately upon receiving the dishwasher I noticed a good size scratch. I had it serviced within one month of purchase because dishes were coming out dripping wet. Technician came out and told me I needed to add rinse aid. I had been using rinse aid, which I think is ridiculous to have to buy an additional bottle of something that’s not even cheap just so this thing dries dishes but moving on...Now it’s been 1.7 years and I’m having more problems. Top rack of dishwasher is broken and falls to the side every time you pull it out. The door to dishwasher also no longer has any spring. I take very good care of my things and this just unbelievable. I called Lowe’s they won’t help because it’s been more than a year! I guess Lowe’s can’t stand behind their merchandise for more than a year because they know they’re selling garbage. I called Whirlpool directly and was told they would come out and service my appliance for a minimum charge if $189! I have no words. I need to buy a stove in the next week and I assure you I will steer clear of Whirlpool. Like the title of my review I feel absolutely robbed.

Washer has rusted out after only four years. I bought my set from Sears, and thought I would get good use out of it for many years; but I am experiencing rust falling from around the rim of the washer. Very dissatisfied with the product, I will never buy another appliance from Sears again. I have always used Sears appliances but after this experience I would not recommend Sears to anyone. I was told that the warranty was for one year, and the rust would not have been covered anyway. Very Dissatisfied Consumer. I thought Sears would stand behind their products. Yea, right.

This oven/range (W10665261B) has a cleaning feature that DOES NOT WORK! Do not buy unless you want to hand scrub the oven without any cleaning products. No one at the company cares. I will discard the oven.

This washing machine has not worked well from the time I bought it two years ago. It never fills to the amount of water required to clean clothes, it is always off balance, so I need to adjust the clothes at least five times per load. I end up wringing my load out by hand. The clothes come out smelly and not clean. After the cycle is done all the clothes smell like mildew. The other night while doing a load, it made such a loud noise in the motor and started to shake up and down, and then moved forward, like it was going to take off or explode. I tried to do another load, but after it filled and started to agitate, it started to make a loud grinding sound and there were 25 minutes left, then the timer showed 26 minutes left, like the computer in the machine is messed up. I had to empty the water out, wring out a load of clothes including towels, exhausting.The worst part is that the machine is finally paid off, I am a single mother on a disability and I am stuck with this piece of junk. I felt desperate so I looked up Cabrio washing machines to try to figure out what could be wrong, and then I find all these negative reviews, and these owners all have the same issues. Why has there not been a recall, or a class act, who can afford to replace a $700.00 washing machine every three years. I also purchased the Cabrio dryer which cost over $700.00. I do not trust that it will be any better in the long run.I cannot rate this machine as it has been a nightmare from the start. White socks seemed to come out with more dirt than when I put them in, and I am sick of using bleach all the time, the fumes make me feel ill. This is not acceptable, obviously this item is defective, and a prominent company such as Whirlpool should take the loss, not all the victims that paid too much in the first place trusting that Whirlpool was a reputable company, I will never give them my trust or business again. I hope to hear from you, and if there has been a recall or class act legal actions, please let me know as I want to be involved.

Purchased a Whirlpool refrigerator model WRF560SEYM in June 2014. In February 2015 the ice maker had to be repaired because of a leak. Now in February of 2016 the ice maker and water dispenser are leaking. Because the warranty is one year, Im basically stuck with a refrigerator that sucks. Not only is the ice maker and water dispenser broken, the door sometimes doesnt shut properly and the shelving couldnt possibly be more cheaply made. This refrigerator is in a vacation home and has barely been used. I have purchased many Whirlpool appliances on the past and have never seen such poor quality in an appliance. The only thing Whirlpool can offer is sorry youre stuck!! No more Whirlpool for me!!

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

This washer is an extremely poor choice if you wash clothes. It has so little water it does not dissolve HE detergent, Clorox 2, or OXI Clean. After even one wash it does not clean your laundry. If you choose to wash your sheets (even though there is a sheets and deep washer setting) its a joke. I could do better by washing things in the tub. I realize its a low usage water washer but you cannot even add more water unless you put it in with a bucket.

We purchased a new Whirlpool in June 2017. About 3 months ago it began making foul tasting ice cubes and now they are so bad we cannot use them. Called Whirlpool for help solving the problem and they basically told me there was no fix. It was my bad water. My water is wonderfully pure and good tasting. It only is bad from the ice in, what I consider a new fridge. They did want to make an appointment for a tech to come out and check it. I dont know why when they told me it cannot be fixed. So sorry we bought a Whirlpool and will never buy any of their products again. Hopefully this will help someone else.

We got what was a top-of-the-line Whirlpool Refrigerator about 10 years ago. It is still running, BUT all of the drawers have broken at least once and the door shelves no longer work. The replacement cost for each item is ridiculous especially considering how flimsy the items are. We decided to look at Whirlpool Refrigerators since the one we have is still running. They have changed absolutely nothing in the drawer or door design. It is all still very flimsy especially compared to the competition. I would strongly advise anyone looking for a fridge to look elsewhere, since, obviously, the quality of the interior is not a priority at Whirlpool. Avoid Whirlpool Refrigerators. The drawers and drawer shelves will ALL break since they have put no effort into fixing obvious defects.

We purchased this machine a couple of years ago... What a disappointment! Was recommended to me by the sales person and I trusted her. The machine does not get our clothes clean!!! We are a couple in our 60s so our clothes dont really get dirty most of the time, but they come out with marks on them all the time. My dish clothes and wash clothes are a disgrace! Im continually trying to soak them to try and get them to look clean. Ive been going to write this review for a long time, but today was the final straw. Washed a small load of towels and had to rewash several pieces! I would never recommend a Whirlpool product after this experience.

I purchased a dishwasher less than 6 months ago from Menards. Since then, I have had to have it repaired twice, due to items getting past the filters and clogging up the drains, so the dishwasher wouldnt drain. I have a 1-year warranty that came with the dishwasher, so both repairs were covered. However, I felt that there should be more done by the company, such as a free extended warranty to cover the cost of repairs as Im sure there will be more; and this is a problem that even the repair man said shouldnt be happening.I called Whirlpool to see what could be done, and all they kept telling me is that I could purchase an extended warranty. I told them (nicely, at first) that I found that ridiculous - why should I pay even more to continue to fix a problem that I shouldnt be having? If they werent going to give me a free extended warranty, I requested at least a partial credit toward another dishwasher, and they could have the piece of junk I have back. They refused to help. I am beyond disappointed with the lack of concern they have for their customers. I will not purchase any more Whirlpool products.

The washer started to show error code for the door and washer would not restart. After removing the top of the washer and checking the door switch to see if there was a loose wire, I traced the wire back to the micro control unit, and upon inspection of the micro control unit, I found that the terminal that the door switch wire was attached to was loose and not making contact with circuit board.Although the washer is out of warranty being 7 years old, this is clearly not a part that is subject to wear and tear. The part was clearly manufactured poorly. I looked on the internet to purchase a new part but it seems that all micro control units are out of stock. This makes me wonder if one should start a class action suit as my part could be one of hundreds that was poorly manufactured. I called Whirlpool to see if they would send me another part to replace the bad unit but they said that because the washer was out of warranty, they could not help.

Washing clothes is a nightmare. I am constantly removing clothing from the washing machine that have been torn and left with holes. I am utterly frustrated. Because the machine is more than three years old, there has been no solution to my problem. I have now replaced clothing items in excess of $2,000. I am always here that they will send a repairman and yet there is still the problem. This machine is costing me too much money. The newer machines have fixed the problem. There is no gap between the drum and the doorway or rubber piece. I want that piece to stop this nightmare. This machine has taken a dream of mine and demolished the experience. I hate washing clothes but more so having a machine at home and then going to the laundromat to stop the chaos with doing laundry at home.

Ive got a brand new house, with brand new appliances by Whirlpool. Within less than 6 months, my dishwasher, Model no. DU1015XTXB0 Serial no. F00702058, had its electronic board gone bad. Instead of replacing the dishwasher, Whirlpool replaced the part. Not even one year later the same part went bad. Now, the dishwasher is not even 18 months old and it will cost $255.00 to repair. It is just the two of us in our home and I bought Cascade packets 20ct x 5 at Sams. Im not even done with the packets, so I know 100% that we have run the dishwasher just 70 cycles in 18 months.

Our Whirlpool Cabrio Washer is barely over one year old, and its getting increasingly louder (I cant hear the TV in the other room). I researched this issue and found this is a common problem with the upper and lower bearings. Check it out on YouTube; its easy to find. Whirlpool should buy these back! Is anyone aware of a class action lawsuit against Whirlpool regarding these pieces of junk?

I have spent more money in the last year to fix this piece of crap. So very disappointed!!! I have lost $$ of food because fridge does not cool.. Ice maker is a joke... I am going to call someone out for the 4th time... Costing me a fortune... Very disgusted with this product.

Bought Whirlpool electric range in Dec. 2005..expensive..so the warranty expired a few months ago. The electronic keypad that controls the oven and lights doesnt work. The repairs will be $408 plus tax which is obscene, and are guaranteed only for 90 days.This after only 5 years of minimal use...just me using it.I will never buy whirlpool again.

I purchased this washer two months ago and have been greatly disappointed with it. I put in a large load on wash cycle, but the rinse cycle is barely any water, and is all soapy water, so then I have to turn it back to wash cycle to get more water and then back to rinse to finish it properly. I was never told about the short water cycle, why not? It is still under warranty, but said I have to deal with Whirlpool, and all they can do is send a repairman out and if it is not a defect, it will cost me $130.00 for the service.

Have had mine for 21 years. Okay, the soap dispenser door would not stay shut after about 19 years. No real problem, just placed the dishwasher tablet on the bottom of a mug on top shelf. Now the timer sticks and has to be rotated manually. I think after 21 years, it is time to replace it with another Whirlpool. This one owes me nothing for 21 years service.

I purchased a new home and then purchased 4 appliances, all Whirlpool Gold. In less than a year, the stoves electronic ignition and the microwave hood keypad went out. Since they were under warranty, a repairman replaced a bunch of parts and now they are working fine. One month after the refrigerator was out of warranty, the water line to the ice cube maker split about an inch and a half and water would spew out onto the hardwood floor under the unit. We were on vacation for all that month and didnt see any damage until one day there was a puddle in front of the refrigerator. When we pulled it out, we saw that the floor was ruined under the unit, the cabinet next to it black with mold and of course, the line had to be replaced. Whirlpool wasnt interested in the fact that the refrigerator had probably still been under warranty when the split occurred, only that we hadnt reported it before the warranty expired. Next to go was the water seal that goes on the inside of the door of the dishwasher. I was running it about a month after the refrigerator debacle and water came spewing out of the side. The seal had come out and nothing was stopping the water from exiting out the side of the door. Thats 4 for 4 in less than 15 months. I will never buy a Whirlpool product. They couldnt be any worse.

We moved to a new house Nov. of 2012 and I went to Lowes to buy a new refrigerator. The last refrigerator we bought was a Maytag. It was a LEMON and probably had every part replaced because we had the warranty. At Lowes I thought the Whirlpool Refrigerator would be a good choice. We didnt purchase the warranty, big mistake. After only 4 YEARS, the refrigerator is DEAD, not in working order and would too expensive to fix says our reliable repair serviceman.

Whirlpool convection/microwave GMH6185XVS - In 2011, we purchased a whole new kitchen for our home with the top of the line Whirlpool products. The sorry side of this project was our microwave. This product has been terrible for us! It has been removed from our wall 4 times for failing... and four times we have gone for weeks at a time with a big hole in our kitchen wall!! All of the failures were due to the microwave not heating food or drink, and all, according to our local dealership, were for various different reasons. Again, it has failed and our local appliance center who we bought everything from does not want to deal with it anymore. I dont blame them... I dont either!! It looks beautiful up there above our range telling me the time of day... My wife and I are older adults and take very good care of everything we own. There certainly has never been any abuse to this product (not to mention we spend half our year at a winter home so this microwave only is used for 6 months a year). I contacted Whirlpool customer service about the reliability of this product and their response was that it is now not under warranty and we should deal with our local store about repairs. I have a small Sharp microwave sitting on the counter below this crappy excuse for one that stays there all the time in anticipation on the Whirlpool going down!!! The $60.00 Sharp never fails me!! This was our 2nd time around purchasing all Whirlpool products for our house. We did the same thing when we built back in 1990. All appliances performed as they should have back then. It seems Whirlpool integrity has gone downhill. I will never buy another Whirlpool product nor I will recommend to anyone I know to do the same. Good luck to anyone who purchased one of these.

I bought an adapter that I added to the kitchen pipe, drilled a few holes in my cabinets to route the hose and voila! It is small but big enough so it's perfect for me. I didn't realize it had an internal heater so I was moving the hose between hot & cold under the sink but now that I know. I will try the heater. The settings are complicated so you have to read the instructions fully. Before I read them I thought every load took 2-3 hours but they don't. I do like to use the heavy soil setting and that does take a couple hours, but if I'm in a hurry or the load is not that bad I use a shorter 50 min setting. For the drain hose I either put it out the window or put a screen in the sink & tie it to the faucet. You have to tie it down wherever you aim it because the water comes out with enough force to throw the hose. I had a couple incidents of kitchen flood before this stuck in my head, now that sucker is secured well. I intend to make a permanent drain to the pipe eventually but for now I just use window/ sink. This required a longer drain hose. For apartment use, I am very happy.

My mother and grandmother swore by Whirlpool washers. They were the best. So, naturally I never wanted any other brand - then came the digital machines. End of an era. My experience with my 1 year old digital machine has been very frustrating. I do not like it. I prefer the old system.

I also have a side-by-side Whirlpool Gold Fridge purchased from Lowes Retail Store, and I paid $1,480.00 for it. It is now 4 years old and I just noticed large cracks on right, inside part of the fridge. I called Whirlpool and got a runaround. Some lame guy said, Sorry, nothing we can do for you.When are people going to stand up for their rights and fight for their bucks? They havent heard the last of me but I will put this on the back of my truck with a nice sign on it for thousands to see. If anyone else has had this problem email me at ** and lets talk. I will never buy any Whirlpool items ever, ever again! Buyers beware! I also hold Lowes Retail Store responsible for this. They should research and stand behind what they sell, they are no better than Whirlpool!

Problem resolved - This is an update to my previous complaint... The repair man arrived this morning and after resetting the thermostat, the water heater started up again. He explained to me that these new water heaters are super sensitive because of the new designs and systems that are required by the State of California. He said that all brands have to have the same system. He said that the new water heaters dont breathe as well as the old ones. In our case, he suspected that after being installed, there were probably some air bubbles in the pipes which tricked the computer into telling it that there was not enough ventilation, when in fact our ventilation was fine, but that triggered a total shut down! In my previous written complaint, I was really upset because I have not had a shower in 3 days and thought this problem water heater would not be fixed until next week. I was furious! My understanding is that basically the way the new water heaters are designed is not very well and there is nothing we can do because about it they are all the same, unless we want to go to a tankless water heater system which plumbing included would cost $4000.00... so we are stuck and hope this will not happen again!

After owning the Cabrio washing machine (WTW5700XW, purchase price $629) for approximately 18 months, it began stalling at the spin cycle, leaving the clothes sopping wet. We found we had to unplug the machine to reboot the computer, and then we were able to manually choose the drain and spin cycle to complete the cycle. Before beginning a new wash cycle, we have to unplug to reboot again, or it sticks in a perpetual pump cycle.I scheduled a repair appointment from the Whirlpool automated service system. The repair man determined the computer control panel has to be replaced. Diagnostic service call was $136, repair est, $321.67, repair service call, $60-130. Total repair cost on an 18-month old machine was $520+. I declined the repair in hope of getting extended warranty coverage from Whirlpool. Nobody has responded to my email complaint from one week ago, not even a computer acknowledgment of receipt of my email.

2 years of use the wash plate went. $150 later, one year later wash plate went again (the wash plate is all plastic, the motor spline in metal total stripes the plastic teeth in the wash plate) I replace myself. 3 weeks later the shift actuator failed which cost another $60 which I replaced. Now the bearing is going. There are only 3 people living in the house. I would stay away from the top loader washers from Whirlpool h2 low series. Huge disappointment.

Purchased this oven in September 2012. Three months in, we tried to use the self-cleaning feature and blew a thermal link (guessing terminology). Tech came out and got the oven open and that was his determination. Also said he would replace both the front and the rear one because it was pretty common that if one was bad the other would probably follow. Said hed have it within a because he had to order it from the factory. I called a week later because no revisit had been scheduled and found out that the factory also did not have the part and was sending me a new unit. Whirlpool was supposed to call and tell me that and did not. It would be another week. Then a few more days for them to come out and replace it and pick up the original unit.Now I have brand new unit again so we tried the self-cleaner. Same issue. To make a long story short I called again this morning and scheduled yet another service call because the oven is inoperable again after running the self-cleaner. This is the 4th time with the replacement oven. They have replaced the thermal units several times and have replaced the fan.Fortunately, when I complained vehemently about the original unit, Whirlpool gave me a one year extended warranty on the replacement so I am still under warranty, which, if youre dumb enough to buy a Whirlpool after reading this, I would advise paying for. If you already have one and are having similar issues, call Whirlpool and insist they give you one for free because they sell junk.This time I told the nice customer service lady that, since the holidays are over and I can get by without the oven, I am going to run the self-clean right after the tech leaves. When it blows and gets repaired again I am going to repeat the process until they refund my money or send me something that works. Whirlpool apparently doesnt care because in their agreement with their service companies they only have to pay for the first visit. After that they just supply parts. I will keep doing this until I run out of service companies in Denver. Then I am going to pay for another extended warranty when this one ends in September 2014 and continue the process.Wake up Whirlpool!! If these units fail consistently at high altitudes (which every tech that has come out here has mentioned as an issue) then fix the problem or quit selling it in these areas.

The washing machine is so loud when it is on, drowning out conversations esp when cooking or eating (it’s located in the kitchen). The machine tumbler has to be constantly readjusted no matter the size of the wash or how many times my husband or myself adjust the tumbler; consequently the washing machine is always dancing, making a horrible banging noise. The washer is under 6 years old. With that said, when you open it, the lip is all rusted out.

Whirlpool Cabrio Platinum Washer Model WTW8800YC1 - I bought the Cabrio washer and dryer pair about 2 years ago at Lowes. About 5 weeks ago the lid fell apart. The hinge area came loose so now there are three pieces to line up (glass lid, metal arm, plastic frame), the fourth piece fell off completely. If you are successful at lining them up you can push the lid down and set a weight on it in order to wash. My first repairman said it was common issue. He expedited a lid. Three weeks later I called to find out when it may be repaired. He said he hadnt gotten the part from Whirlpool. I called Whirlpool... nice lady told me the part was on back order but should ship the first of the week. So on week 4 after not hearing anything I called a new appliance repair person. It is going to cost about $280 dollars to repair. This is one third the cost of a new washer??? I fight with this machine every day to get it to wash.

Hi Folks, so today I had the pleasure to speak to Whirlpool regarding a repair bill on our washing machine which now has a bearing failure and estimate to repair was 1279.00. Its 6.5 Yrs old, just out of extended warranty and cost me with the pedestal a total of 1250.00 when new. I explained that in the 6.5 since I have lived at this house where we spend all new Whirlpool Gold Appliances, half have now failed. Range Microwave, Dishwasher and now the 1250.00 front loader is dying a slow and agonizing death with a bearing failure. Just so everyone understands, the estimate is from an official Whirlpool repair service that was booked through the Whirlpool website. Other repair folks just would not bother to look at it when I told them I believe the bearing was going bad.The repair man that arrived was professional and on time. However, I had a hard time understanding how a 6.5 Yr old washing machine would be considered beyond economical repair by costing 1279.00 to repair. Labor was 250.00 which I thought was fair. Time, etc. But parts made up the difference in cost. So later in the day, I spoke to Whirlpool and they offered the equal new washer for what would seem an excellent price. About half off. Wow, I thought that sounded good. So I asked if my existing pedestal would work with the new washer and it did not and I would have to pay for one. Regardless if my old one was fine or not.So, they offered a discounted rate from new at another half off. Total approx 800.00. So, I asked the Whirlpool rep to hold on and I need to check with my wife if she wants the replacement. She uses it as much as I do and wanted her thoughts. She checked the model on the washer and pedestal and with the local Home improvement store, they have it on sale for both units (washer and pedestal) and its about 50.00 less?Consequently, I called Whirlpool back and explained that it does not move the needle to regain my trust as compensation on a 6 yr bearing failure, failed dishwasher and range microwave they offer what a distributor of their product can offer for less as a package? Really? I mean, the Home improvement store is not in the business to lose money. Now, I am having a hard time understanding my own failure to have trust in a brand I used to have with my previous house.My mom had an old Whirlpool washing machine that lasted 25 years before she and my dad gave it away. You know, the old white top loader they used to make back in the 70s. Sheet metal, made a racket and never broke? Oh yeah got the clothes clean too! I dont know what to make of it anymore. So, I will just wait till it dies and take my hard earned money and spend it on another brand in my next house which we are going to move to soon. Maybe I can feel nostalgic and find my moms old washer. Its probably washing someones rags right now and getting them clean. It must be 35 yrs old by now.I dont expect to get anything for free. Its out of warranty, so I need to deal with the consequences, but there are steps the other party can take to help remedy the situation. I think they tried and it was genuine but in my thoughts its just not enough when your local box store is offering the same. When you develop a brand to extend a message of trust in quality and value, you need to have quality and value all the time. I suggested they help with the costs on the parts. I would certainly pay for the labor. Parts cost little to the manufacturer. Unable to help that way. I thought it was cheaper for them too. Guess not. Its come to be a throw away washing machine at 6.5 yrs and I am Infinitely disappointed. I just want my washing machine to work as well as my mothers old one and have the possibility to fix once in a while when needed.

I currently rent, and so when our literally 30-yr. old GE dishwasher broke down, our landlords went out and installed us a new Whirlpool Dishwasher. I was excited because FINALLY I would have clean dishes and a dishwasher that didnt leak a bucket of water all over the floor. Well, weve had it for about 6-8 months now and I have to say that I am not impressed. It is not as great as I thought itd be. First of all, my dishes still look cloudy (despite using various brands - even homemade - detergent). Second, one out of every three washes gives me still-dirty dishes (food still on them, even though I rinse before loading the dishes). Now, Im not talking about tough stuck-on, need a jack-hammer to remove food. Just normal food. Mostly it is oil, like if I had a plate that I had eaten French fries on and there was grease left behind that normal rinsing didnt remove. A new dishwasher SHOULD be able to clean that! Third, it guzzles Jet Dry liquid (or whatever rinse aid you use) like an alcoholic in a bar. I have used a BIG bottle in one month. One month. With the old 30 yr. old dishwasher, it took me around 2 YEARS to use a big bottle. And lastly, it takes F-O-R-E-V-E-R to wash a load. My old dishwasher took an hour tops - to rinse, wash, rinse, and dry - and it was 30 years old. This new Whirlpool takes 3 HOURS!!! I can literally hand-wash all of my dishes (and with a family of 4 thats a lot of dirty dishes in one day), sit them out to air dry, and take a nap and it take LESS TIME than using the dishwasher. The dishwasher has all the bells and whistles to make it look good, but trust me, if I could have had the 30-year old dishwasher rebuilt to newness, I would have begged my landlord to do that instead. Dont waste your money on Whirlpool appliances. I left another less than friendly review for my Whirlpool Cabrio washer (only 5 years old), if you care to see it. Learned my lesson, dont buy Whirlpool. So disappointed because they used to be (USED TO BE) a reputable dependable brand.

Ive always had good luck with Whirlpool. They last longer & dont have as many repairs. Ive had to have a lot of repairs with Maytag washers. The dryers didnt give any trouble. I recommend Whirlpool.

We have never had problems with our old Kenmore appliances. Since we have had the Whirlpool complete set we have had problems with both the Refrigerator and now the Stove. The fridge had already been re-engineered by the time the repair man got here but the fix didnt work. We had a 50 degree refrigerator for over a month. Now the stove wont keep a constant temperature so we wait for the service man once again. They look beautiful but they are the worst we have owned over our 36 years. They obviously have engineering issues looking at all the other reviews. I dont see us purchasing another Whirlpool appliance in the future.

We had our microwave and stove delivered in October, 2015. We had 4 deliveries of the microwave. The first two were damaged, the third needed a new fan motor and the door was not straight. They wanted to send parts to fix but we could not see spending all that money for a brand new microwave to have parts put in. I complained a lot to both Whirlpool who would not replace it and ABC Warehouse who finally agreed to replace it with a brand new one. The 4th is good. (so far).Our stove has a flaw in the glass top, the drawer doesnt close properly, and there is a piece of metal sticking out from the lower right side of the oven door. ABC says they cannot do anything about it and Whirlpool says it is under a parts warranty so it has to be repaired. I even spoke to supervisor Kimberly at Whirlpool. Got same answer. We are very angry and disappointed. As I told the Kimberly, Whirlpool got every penny they asked for. We paid for brand new in perfect condition and got a stove that needs fixing. We will never recommend Whirlpool as a Company for appliances and based on all the negative reviews Ive read, neither will a lot of other people.

I bought a Cabrio 2 yrs. ago and I wish I had my old washer back. I read reviews and checked out a lot of literature and thought I was getting a quality machine. What a waste of hard earned money. I cant get clothes clean, its loud, and it leaves soap residue even after an extra rinse. Whirlpool products arent what they claim to be. I had a freezer I bought because I bought a half a steer and it quit running and I lost all my beef - $700.00 worth. From now on I will stay away from any Whirlpool products!!

Do not ever buy a Whirlpool refrigerator. Sloppy construction, bins dont close, doors dont seal well and a brand new fridge doesnt cool to a safe food zone. When we call for service, I got the run around for almost 2 hours. They wont be sending anyone to service a brand new unit for an entire week... And thats 2 days before Thanksgiving! I have never had an appliance made this poorly. We dont have the space for a bigger unit, so thats why we bought this model. Size shouldnt impact quality!

Whirlpool Cabrio Purchased 12-7-2012 - what a piece of junk. Does not get clothes clean, rarely does she even spin out properly. Called because it kept walking across the basement floor. Informed that was the owners responsibility, not the store (Feidens in Latham). Always had good luck with them, bought all my appliances from them. Now I heard a loud bang and she threw up - water everywhere. What a mess.Had purchased special patio block at Home Depot to even her out and every time I used it which was not too often, it acted like the space shuttle ready to head down the runway! Not too happy with Feidens attitude with regard to this purchase. Not going to call them to fix it. Not an ready to pay to listen to their guff again. Expensive machine never worked well since it got here. I always wished for a Whirlpool, be careful what you wish for! Junk, nothing but junk. Only 3 years old and I only do laundry about every 3 or 4 weeks. Live alone, so she certainly was not overworked.

We paid $6,000 over and above my homes purchase price for double ovens that are defective. Whirlpool will not address the problem! When you bake a pie or a turkey, the bottom and center are raw, and the top burns, because the bottom element is hidden under the bottom of the oven, instead of on top of the interior floor area of the oven. Whirlpools new design is defective! The service technician says the oven is performing as designed therefore there is a design defect! However, Whirlpool will not take any action, because the parts are not broken and they send us back to the extended service plan people. It is ridiculous for the consumer to be caught in the middle. Whirlpool does not want to stand by their product.The builder of our home, Coleman Homes in Middleton, ID, purchased the ovens from Whirlpool originally. Therefore Whirlpool says we are not the original purchaser of the product, Coleman Homes are, and Whirlpool cannot do anything because we did not buy the ovens directly from Whirlpool ourselves, Coleman Homes did. The Whirlpool Warranty (waste of money) says they cannot do anything because it is not a parts issue. Coleman Homes says they cannot do anything because the warranty was given to us when we purchased the home. Whirlpool needs to replace the hidden element with a true baking element so the ovens will bake properly!!! Model Number: WOD51EC0AS Serial Number: D52208658

I have a Whirlpool Duet front loader. Sick of it since I bought it! Not enough water to wash & rinse clothes. After consulting sites on internet, husband decided to try adjusting part. He just took off the 3 screws & lifted top off. On the outside part that has a white plastic housing, he turned the longer screw 2 1/4 times clockwise. EUREKA! We have more water! You may need to start out adjusting 1 turn & work up till you see a water level you like. Just dont let the water come over the wide rubber water guard.

After purchasing three gold series kitchen appliances in 2013 two months after purchase refrigerator failed. Whirlpool did not have a fix at the time. Told me I had to wait two months for a part to be engineered and then service to be scheduled which is not acceptable. They would not take back the refrigerator and give me a different model so I had to press Lowes to accept it back and they did give me a refund. I then had to purchase a different brand refrigerator which now I dont have a matching set in my kitchen.Then the dishwasher became part of class action lawsuit and now my gold series gas range is obviously damaged too. The control had the plastic panel is bubbling and it is split. Again after talking with Whirlpool customer service they refused to help with this at all claiming this is a cosmetic issue and it wouldve only been covered for 30 days from date of purchase. This gas range also has an aqua lift self-cleaning feature which does absolutely nothing. It does not clean the stove. You have to go into it and clean it the old-fashioned way with chemicals, gloves, mask and a scrub brush. These products are absolute junk and the customer support is non-existent. Do not buy Whirlpool products.

Purchased a Whirlpool washer and dryer (WFW75HEFW0) in September 2017. Have had 4 service calls on washer for not completely washing clothes, leaving excess water after cycles complete, excessive wrinkling of clothes even on non wrinkle clothes, odor on some clothes due to incomplete water fill on some cycles. Factory position since there are no error codes washer is fine. Asked factory to exchange washer and upgrade model which we would pay difference. Denied. Looking for another brand and will seek legal assistance in the matter.

I purchased a condo last year with all appliances included. My Whirlpool refrigerator model is GI6SDRXXY00, a fairly new refrigerator. I noticed orange and moldy spots on ices when dispensing them. I changed the filter, thought maybe it is the filter causing the issue. But after inserting the new filter and emptying the entire ice tray, I still get bad ice! I open the compartment, and surprisingly, found out that the spiral rod inside the ice dispenser was rusted! This is horrible and unacceptable! This is not a user fault but a manufacturing defect. The parts that are in direct contact with what customer consumes should be robust and safe. I contacted customer service, and they gave me a technician phone number which turned out to be a third party which only cares about money. They said they will inspect the refrigerator and will charge me $134.00. I will not use this refrigerator anymore and will replace it soon. AND I will never purchase any more Whirlpool products. This manufacturer is crossed out from my list of vendors who I do business with.

Just plain terrible. Purchased Whirlpool Gold Seris Dishwasher Model w10698637a in June and now its been 3 attempts so far to fix a brand new dishwasher that does not clean. So far I have been asked... have you been heating the water before you start the cycle?, my favorite... Is this a whirlpool dishwasher. So I find out today that it will take another visit from a company that hasnt been able to fix it, plus a call to the tech line to make sure they havent missed anything. Heres what Ive missed, a dishwasher that cleans.

We too have nothing but problems with our supposedly top of the line convection/microwave oven. Purchased in 2010 in February for new kitchen. From start, original microwave installed did not work, would not cook or heat. Dealer replaced. One year later, same problem, but now out of warranty. Had to pay labor, costs, and parts to get fixed. Fast forward 13 months, again magnetron needs replaced, microwave will not work. What a hunk of junk for our money. I will never buy any Whirlpool appliances again, and I will tell everyone I know the same. When you call customer service, they are nice but only say “too bad, out of warranty”. What a joke for a major appliance company to tell customers. It is obvious that this microwave is faulty from the get go, and they just keep on making them the same way and not trying to fix the problem.

We have had the washing machine about four months. When washing sheets, they twist up badly. The machine does not seem to get the clothes very clean. It seems that it does better when we put it on the bulky setting for all washing that we do. More water is needed I guess.

Originally, I loved my machine. At the one year mark, my washing machine began a f51 error code. I looked it up and it had a recall. The entire board had to be replaced. Now, I keep getting a ul code and it will not quit. Also, the inside of the top is rusting out so badly that chunks of rust fall into the washing machine and stain my clothes. I wish Whirlpool would fix these common errors. I see many other people complaining online that the same thing is happening over and over.

Purchased on Nov 2010 at Lowes. Washer machine sounds like an airplane on the wash and worst on the spin cycles. Bearings are gone!! Customer service was no help. Basically was told I was ** out of luck. Have service bulletin addressing this issue, yet they refused to help. $1300 learning experience about Whirlpool. Social media here we come. Goal: to keep at least 1 million customers away from their scrap!!

I owned a Whirlpool refrigerator for over 16 years and never had a problem. Purchased a new one about 21/2 years ago only because I moved and the size didn’t fit. Love my Whirlpool refrigerator. No complaints.

Replaced an old water heater with new Whirlpool 40 gal. short natural gas water heater N40561-403. Good instruction, very clear directions. Also purchased at Lowes was a Utilitech universal gas water heater installation kit. The nipples provided in the kit screwed very loosely into cold water inlet and hot water outlet. I used teflon tape and finished the installation. When I turned the water on both fittings leaked. I couldnt tighten the nipples any further so I shut the water off and drained the tank a bit and reinstalled the nipples with at least 8-9 wraps of teflon tape. Im not sure if that is normal or if nipples were under size or if the cold water inlet and hot water outlet were larger dia. than normal. FYI.

I bought a washer and dryer a couple months ago. The washer has been completely replaced already. It is a piece of garbage. I have to wash my laundry four times and still my clothes are not coming out clean. I have three small children and it is just a pain to always be washing their clothes. Things as simple as orange juice not coming out of a shirt even using bleach. It was sold to me with high efficiency and great water consumption but of course it is, it doesnt use any water to wash the clothes. I had a tech come out to look at it and even they said its had so many complaints about how it washes. She said that the wash machine is the worst out there and I totally agree. If you cant wash baby clothes and get puke out of a bed sheet then I could just imagine grass stains. Wash machines don’t last forever but I can promise you I will never purchase another in my life. Best part of it is when whirlpool was approached, did absolutely nothing about. Basically said, “Have a good day, thats what you bought, thats what you get.” Considering its still under a year warranty. Tell me I will never buy a whirlpool again and I will never recommend one to anyone who asks. The customer service and product dont stand anything against other manufactures. I learned my lesson the hard way but Ive opened my eyes. Never purchase a top loader. Word of mouth travels fast. I know my complaint probably means ** to whirlpool but for what its worth, Ill be spreading the word around.

I own a Whirlpool Cabrio washer, model #WTW7800XWO. The lid to the washer has completely detached for lack of a better word. It literally blew-off during the spin cycle and is hanging on by one hinge. My husband is disabled and I have had to go without using the washer for several days, waiting on a repair person not to mention the expense that will be incurred.This was a very potentially dangerous situation. My washer is barely older than one year. To add insult to injury, when I contacted the customer service department, I was told I would have to purchase and replace the lid or pay $299.00 for warranty insurance to have it covered because this is not considered a Quality Control issue.The service person has told me that both hinges and the lid will have to be ordered and replaced, leaving me without a washer for several more days. No one has been able to tell me why this happened. I fear this happening again after repair and do not feel safe with this washer. I would appreciate a response as soon as possible.

Having serious health issues with both our washer and dryer. I believe there should be an urgency and more serious resolution. Our washing machine is getting clothes trapped and producing friction causing excessive and heavy smoke from the drum. Our dryer has a random bolt/screw in the drum that catches and tears clothes. Although this doesnt happen on every cycle. It happens enough that it should be investigated, repaired and reported to Health Canada. I contacted Whirlpool on September 15th 2015 with my concerns. Nothing is being done! Ridiculous. WASHER Serial: HL23299429, DRYER Serial: M24507313.

Whirlpool dishwasher Wdt790slym1 - This is the worst dishwasher I have ever bought. The top rack assembly is made of all plastic and started falling apart within 13 months of purchase. I have had to order the same replacement parts numerous times and have reached the end of my patience. Buyer beware!!

Had washer less than 1 year and washer stopped and was flashing code F 51. Called Whirlpool and they sent a repair person. He worked on it and didnt fix problem. Called Whirlpool back. They had to order parts. Repairman came back - replaced parts. Now not 6 months later same thing happening. Whirlpool said we have to pay for labor to repair again. We went online after this happened the first time and saw where others had same problem - this washer should be recalled. The repairman said this part was corroding. This should not be happening on a new washer. We will never buy another Whirlpool product again!!!! Im concerned that it will keep repeating over and over and we paid 700+ for this washer not 1 1/2 ago. My last washer lasted 15 years!!! Wasnt a Whirlpool!!!

I have had this Whirlpool Cabrio washer for 4 years. I had to rebuild the drive unit once and now the control board is bad. If I didnt do my own repairs I would have spent well over the cost of the washer in the 4 years I have owned it. This is the worst washer on the market. Not to mention Whirlpool support will not work with you at all. DO NOT BUY THIS PRODUCT.

After happily using Maytag washers at my old address for 30 some years, I moved to my current address and in 2006 I purchased a new Maytag. In 2010 I needed service. I was advised it had a bad bearing and was not advised to repair as it would cost well over $600.00. I purchased a Whirlpool Cabrio top loading HE appliance.The Cabrio worked well until one day it made a horrible noise. Although it still worked, I called for service and was told it had a bad bearing and would cost $670.00 to fix and they advised against it. After the service call, it never worked again. I know things dont last like they used to but 4 years is ridiculous. I have been advised that Whirlpool bought Maytag. Is this what to expect from so called reputable companies?

Its amazing to me that every other complaint listed here is identical to the problems I have had with my Duet washer. In the past 4 years, I have had two Duet washers and now, the 2nd one has to be replaced. On the first, the control board blew and it was too expensive to consider replacing. I had a new Duet later that day (I use a great, small local appliance store that is reliable and has a great reputation so I know Im not being screwed over). This one made it for 3 years before the bearing broke. It sounds like its about to launch into orbit. I can either continue to use it until it stops working (likely very soon) or just replace it now as its too expensive to repair. I cant take a chance on it breaking down, so...Thats a good gig Whirlpool has, huh? Repairs are prohibitively expensive so they sell more machines. Whirlpool appliances used to be among the most reliable and well-made. Not any more. Two Duet washers in 4 years in my honest opinion is ludicrous. When it did work, it seemed to do the job and I have to admit to very, very heavy use (3-5 loads/day). But the days of a washer lasting 20-30 years are long over.

Out of warranty, slab of ice forms every few weeks in bottom of freezer. I have to take a butter knife and chisel it out to prevent having to defrost the entire freezer. This is clearly not isolated as after reading online and this forum, it is a manufacturing DEFECT that should be fixed at no charge to the consumer. It was delivered and installed by the retailer that sold the brand - however it sounds that Whirlpool would rather lose customers to other brands - trust me I just bought a stove and bet your sweet behind it was NOT a Whirlpool. Neither will the replacement for this piece of crap be once I can scrounge up the money.

Ice machine went out right after the year warranty was up. Convenient right? We called a hometown tech to come out and look at the water valve. He was unable to locate it, so we called Whirlpool service. After waiting 30 mins, they told us they cant tell us where to locate it for safety reasons, and if we wanted anything done to the refrigerator, we needed to pay a tech to come see it. EXTREMELY RUDE!!! I would NOT recommend whirlpool ANYTHING.

I got the works; the stove, dishwasher and refrigerator. I cannot believe all the BS you got to do to baby these appliances. If I had designed this mess... I would not be selling it. Every one of the appliances has a issue... the oven takes a long time just to cook toast. I would send them all back... but from what I have been told this is it. They all suck! I sure wish I had my older appliances back. I see the city dump in their future! I got the black stainless. Believe me I am not happy at all. The repair people have already had to fix or replace parts and I have not had this stuff for 30 days yet.

I have the same lid closure issue expressed by many consumers and whirlpool refuses to acknowledge this as an issue, only recommends purchasing a new lid at $225. Lid design is flawed, metal L bracket connects to plastic housing/trim/side of lid, causing glass to pop out and stress cracks between screws. New models of same washer have redesigned lid, no cross reference part number or dimensions listed to determine if new lid will fit.

My KitchenAid side by side refrigerator/freezer is a beautiful thing, shiny steel surface, gleaming white inside. However, its made poorly. The ice cube maker compartment broke and the replacement came without any installation instructions. It was hard to figure out and I broke it. Now, everything in the refrigerator is freezing and changing the temperature on the digital panel makes no difference. McKinneys appliance, where I bought it, no longer has a refrigeration technician and they referred me to Whirlpools 1-800 number where I supplied some information and sat in my chair on hold listening to music for a half hour before hanging up.The recording on the phone suggested their online chat where I was asked the same sorts of questions and was told I would get the answers I wanted by paying $5.00. I had no idea what I was getting into but I didnt pay, just terminated that inquiry. Feeling cheated by the company whose product I had mistakenly purchased. Im now running the risk of a technician visit, sometime between 8 am and 4 pm a couple of days from now. I have to be prepared to wait around all day for somebody to look at my refrigerator, charge me a lot of money and, from what Ive read online, potentially see the problem return in a very short space of time.

I am pleased with the steel tub, the ability to do an extra rinse and spin and especially the choices of water level that it determines by the size of the load. Its ability save water use. I would repurchase the top loader again. My clothes come out looking wonderful especially the whites and I do not use bleach. It does not get the mold or mildew odor that my last machine would get due to the rubber or plastic made tub. I love it.

Whirlpool cabrio top loader is junk from the first month. My washer has had way too many repairs. A&E repair has been a frequent at my home. Now Im getting ready to repair it again! Hub gasket or pump not sure this time. All has been replaced previously. Never ending - always something wrong with it!!!

Whirlpool dishwasher failed after 16 months. It leaks continuously. they sent a service provider 5 days later out to fix it, then said there would be a $129 fee for coming (this was never mentioned at time of appointment), and the total repair cost would be $208. I wasted a day waiting for repair person to come, I declined the repair due to the cost. I called customer service later, during office hours, and I received the poorest level of customer service I have ever experienced. Whirlpool will no longer receive support from the our family. This machine cost over $500, and a ruined rug. Whirlpool wasted our time, and a day from work. We will never purchase Whirlpool appliances moving forward, due to this product and customer service experience.

Purchased gas water heater from Lowes in 2012. Had no problems until July 2018. Its under warranty but have had to replace the control valve completely and the burner 5 times and it still is not fixed. Dont waste your money. Buy something else.

I bought a Whirlpool fridge 4/23/2013. Thanksgiving it went out. I had a repair company come look at it to see how much it would be to repair. He said the compressor was out, it has a freon leak, and the electric board has a relay that is acting up. Basically it would cost $600 or more to fix. I only paid $750, mind you. Whirlpool customer service said if we pay to have it fixed then send them the paid receipt. They would then give me a 6 month service plan for future repairs if needed. Please tell me how that helps me now? A voucher for $200 or offer something to help me now. Not a happy customer. Thanks for nothing Whirlpool.

I purchased my Cabrio washer and dryer 2 1/2 years ago, and for the past 6 months, I have dealt with it being unbalanced and I tried everything to get it balanced. When I researched the problems, I found so many other consumers are having the same problems and that Whirlpool will do nothing about it. I decided to start a petition on Change website to try to force Whirlpool to stand behind their product and correct the problem, offer us a refund or another product, or even fix the darn thing. It is tough economic times, and we spent money to have something that was energy-efficient as well as a product that is supposed to carry a good name. I am a single mother with three children, and I dont have a $1000.00 to throw away after 2 years. This is shameful that we, the consumers, have to deal with this. Please go to the Change website and sign my petition. The more signatures I get, the more leverage we have to deal with Whirlpool. Lets pull together and show Whirlpool we will not stand for them robbing us of a quality product. Thank you so very much.

Whirlpool Duet washing machine model WFW9500TW03 - Just after the first year of owning this machine, the metal hinge to the door cracked and the door didnt shut properly. It was replaced. After a couple of years, the bearings and drum of this machine failed. The cost for parts and repair were as much as the machine new. After repairs, the machine never ran quietly again. I have called for repair a second time for the same issue and he has confirmed that its the bearings again causing the drum to dislocate and hence, break the belt that I now need to replace. My problem is with Whirlpool for its defective metal in its machines (many complaints on the internet will confirm this). I believe there are enough consumers out there to file a class action lawsuit.

I WILL NEVER PURCHASE ANOTHER WHIRLPOOL PRODUCT IN MY LIFETIME!!!! If I could I would rate this fridge and Whirlpool’s repair and customer service a NEGATIVE 100. My wife and myself purchased this refrigerator on 6/2/19. On 6/16/19 we noticed that it was not cooling as should, we called in to set up a repair service call only to find out that we had to wait until 6/20/19 to have a service tech come out to look at the refrigerator. When the service person came out to look at it he stated that it needed a sensor??? And that they would have to wait until the evaporator thawed out to replace the sensor. We had to reschedule another tech on the following Monday 6/24/19 to replace the part. 8 days after the refrigerator stopped cooling.Now fast forward 2 weeks and now we have the exact same issue, whatever was fixed did not correct the issue. We had to call back into Whirlpool to make a setup another service call. We have to wait 5 more days until a service tech can come out to recheck the issue. Whirlpool offered no other assistance. If I could I would return this defective unit and buy a different brand of refrigerator. I WILL NEVER PURCHASE ANOTHER WHIRLPOOL PRODUCT IN MY LIFETIME!!!! I will make sure that I let everyone I know that I would never recommend a Whirlpool product!!

2010 upright Whirlpool freezer - Door is totally bubbled in rust. Warranty Plan not covered for this. Whirlpool Corp Serv. Dept said they are sorry but it is not a functional problem. Cost of repairs on 3-yr-old freezer that cost $600.00 would be $732.62. This freezer was rated CR Best Buy in Sept 2009 which was why I purchased it. I paid $81.00 for repair tech from Whirlpool today who could do nothing either. Whirlpool knows that this has been a problem as consumers have complained about this rust in Google, some saying they will never buy a Whirlpool product again. Same here!

Purchased Whirlpool set from Lowes March 2016. Washing machine is not worth the metal its made from. Clothes are dirtier after the wash. All white linens are ruined! Clothes wont rinse or spin dry. Whirlpool wont reply nor will contracted repair return. The last repairman told us we would be better off taking the clothes out back and wash with hose because the Cabrio is useless and nothing can be done to fix it. I contacted place of purchase (Lowes). They wont help due to not buying warranty thru them. Stuck with the worse washer ever... never again Whirlpool.

I have a Whirlpool oven and dishwasher and have had nothing but problems with them both since day one! Our oven went out Christmas and couldnt get service on it and we were entertaining for Christmas. DONT EVER BUY A WHIRLPOOL PRODUCT!!! If you do you have no one to blame but yourself.

We purchased a Whirlpool side by side from Lowes and an extended warranty. Immediately maybe a month the ice maker froze. Ice container in the door. Repairman said design is notorious for this problem. This was an ongoing problem. They replaced icemaker and it continued. Finally the warranty people told me it could be deemed a lemon if repaired for the same issue 4 times in a year. They deemed it a LEMON and I received a store credit for the purchase price less the warranty amount. I purchased a new LG French door. No issues and its been 5 years. If you have an extended warranty do some checking on the lemon.

I purchased a Whirlpool Gold top freezer refrigerator (G2IXEFMWQ03) in May 2011. Six months later, the freezer began to collect frost and eventually clogged the refrigerator port from freezer. Since cold air from the freezer was not going to fridge, I had to turn down the refrigerator temp to lowest setting. I had a service person come out and replace Adaptive Defrost Control under warranty - it would have cost me around $250. Now roughly 12 months after repair, the defrost issue is back. The part cost me $175, and that is if I install it myself. I called and mailed Whirlpool which was a waste of time. This is the last Whirlpool I plan to purchase. For the same issue to occur in this short time span, it has engineering flaw written all over it.

Large tub capacity. Door opens wide without stopping. White Finish has not faded or chipped. Quiet and rarely makes noise even when overloaded. Machine bought 12 years ago and has never needed a repair visit. It has been moved from 2 different locations by using the special brackets. Easy to use detergent holder and fabric softener.

I bought a new Whirlpool refrigerator from Sears and within a month the refrigerator side did not maintain temperature where milk would not spoil... Cool but never cold. I called Sears and they said its Whirlpool warranty to contact them. This I did and about a week later they contacted a local service company they use to maintain their equipment... Long story short this will be the 4th time they were informed the refrigerator still doesnt maintain temperature... Food had to be thrown out because of that.I asked them to refund me my cost or at minimum get a working refrigerator to me because after 4 attempts at trying to fix the problem it still exists... They just want to keep sending a repairman out there who still cant figure out the problem and that has cost me much time away from work not the mention the spoiled food costs... Even when complaining my dilemma to the repairman he said, All they will do is keep calling us and kick the can down the road... They could care less about what it has cost me in time and money... I had to give 1 star to this company but they dont deserve even that one... Dont waste you time thinking a warranty by them is worth a flip and now over 3 months Im without a refrigerator...

The bottom of the drawer collects water and freezes and then overflows onto the floor. There is no drain pan under the refrigerator. Then the freezer collects frost over the food, and walls of the freezer. I have to unplug the refrigerator and let it thaw and then plug it back in. This process is repeated every week. I have had it less than 2 years!

Whirlpool Gold refrigerator WRF989SDAH00. I purchased this French door refrigerator based on past experiences with Whirlpool and sad to say this is not the same quality product I have know Whirlpool for. After the warranty ran out, it died. The first service company I called identified the problem as a known (to Whirlpool) design flaw. They would not touch it and referred me to contact Whirlpool. I did and the company referred me to Dinos Appliance Factory Service (in Phoenix AZ). They came out and confirmed it was a design flaw. They replaced the evaporator and compressor and it lasted about 6 weeks.

At some point, Whirlpool should accept the fact that they should not sell this machine. Word of mouth spreads fast! Im hoping it will make a big dent in sales because I know then they will listen and act! I purchased it in 2006 for $800, thinking this Cabrio 6400SW is a dream, I can get more done in less time (at that time, there were seven in our family). However, problems within the first year, F1, but I was happy and still under warranty! It was fixed, only to start the problem again. This time, not under warranty! I really wish I had said yes to the extended warranty! Even the repair guy Whirlpool sent suggested it may be a good thing to get the extended warranty if I were you! I think he was trying to tell me something!My naive thought was, why spend more money we did not have? After all, it is a new machine! I did not comprehend that any company could sell and continue to sell something that was clearly a defective machine! Nor did I entertain the thought that a company would not stand behind their product! It is now 2012, I still have the machine because we have dealt with it and have/had no extra money to throw out at it. I have dealt with F1 for several years and did not contact Whirlpool, mostly out of lack of time to research what the deal was and if others were experiencing the same. In November 2011, after reading many complaints and frustrations on the internet and what results they got, I called Whirlpool. Using a level head, sugar sweet persona and a mindset of disbelief that Whirlpool would allow such problems, the customer service girl did her best with what she was told to reply with (meaning, there is nothing she can do). It is then that you ask to speak with a manager or director. I won in getting a repair guy out to fix the F1. They made it sound like they were doing me a onetime favor. The machine board was replaced, the repair person also thought there was an obstruction in the hose and he could fix it, but it would cost us money and suggested we try our hand at it first. We did find an obstruction and for one week, the machine was quietly working beautifully! Whirlpool even called to see about how it was working and my husband had answered that everything works well, not knowing that Ld is our new problem. Ld had started to pop up at the end of that week.So here it is July and Im so frustrated trying to get wash done. Im thinking of all the wasted time, all the wasted electricity and energy Ive spent trying to get this machine to work! My kids are trained to hit stop/pause if they hear it beeping. Some days we cant even get the clothes to spin dry. I try different cycles to get the machine to start and often have to cancel the cycle and change it to another cycle to get the machine to continue. Is there a smell? Yes, and I run the clean washer cycle twice in a row just about every other week now. That doesnt even seem to clean the washer anymore! Tangled clothes sometimes. Ld always, uL sometimes and a sound like it is trying to do something but is stuck. Lots of laundry to do! No money to fix it! Whirlpool needs to stop selling an inferior machine! I know one thing. Never Whirlpool again and I tell everyone not to go with Whirlpool Cabrio. Even one of my co-workers had one and bought a new washer (not Whirlpool) because of problems with her Cabrio only after three years! Do not purchase a Cabrio!

My new fridge is extremely hard to open. The technician that was sent out told me that there is too much suction building up inside the fridge and freezer and that is why it has to be yanked to open. This is not only annoying it means the fridge is constantly being pulled forward out of place. Technicians solution was to deactive the castors under the fridge. At the time he was here I did not realize that I could then no longer move the fridge out of its place to clean. I called Whirlpool and complained and was told that they could do nothing more for me because the fridge is in good working order. I hardly would call this good working order. They also informed me that if I wished to clean under the fridge or the coils at the back it would require a service call to move the fridge and I WOULD BE CHARGED EACH TIME. Needless to say I AM VERY, VERY UNHAPPY WITH THE WHOLE SITUATION.

I have not had any issues with my washing machine yet as I have only had it for two and a half years. The features the machine offers are good and there are many options. So far the washing machine has worked as advertised / expected.

I was gifted a washer and ventless dryer for my condo. It takes a little longer than a regular dryer but it works great. It fits perfectly in a closet.

My first washer a Sears Kenmore lasted us 25 years before giving it to our son who used it for another 10 years. This machine is compatible with that one. Both are simple with a few of bells and whistles. That is remarkable in todays gotta have all of the fancy gadgets mindset. The Whirlpool machine does a very good job of washing clothing...period!

I purchased the fridge 2nd hand in 2013. It was 10 years old at the time. It is still going strong & I purchased it because it has a frost-free freezer that never needs de-frosting and I love the features & size - its the PERFECT FRIDGE. What I look for in a fridge is its colour - I like metal, steel grey colour. I go for reputation & quality. Frost free is the biggest factor that determines my purchases, long-term (10-year min.) warranty & guarantee, size.

I bought new townhome on 2018, in 6 months the top drawer broken, because stuck, after one year passed from the one year warranty start freezing all my groceries, milk, fruits. I turned off many times, not fixed. I am surprised paying so much money for appliances and turned out so cheap products and last only one year!? Older fridge last 10-15 years!! Companies ripping off people pockets. Very unhappy about this. Now services technician coming we have to pay for ....

I have purchased all new Whirlpool appliances for our new home in March 2009. I have had trouble with the refrigerator door panel and will not switch between ice and water. Cost to replace over $100.00. Now its the range. When turning on the oven, my wife said she saw a flash of bright light and then I turned around and it was smoking up the house! I quickly pull the stove out and unplugged the stove. I then remove the back panel and found the right side of the control panel was burned. Had I not pulled the plug, a fire would have started. I have pictures to prove that! The cost to replace the control panel is $267.00 and that doesnt cover the repair man coming out to test if anything else is bad!

2 yrs after my landlord installed WHM31017AW1... Whirlpool oven stove microwave. The door cracked then another crack and pieces from door fell on stove. I removed all loose pieces then glued all cracks & loose pieces on door. Landlord thought door was being closed too hard, silly. After all reviews same, not buying replacement door but having different brand installed.

Update Review on 10/15/2020: New refrigerator 12/31/19. 4/27/20 Fridge terribly noisy, called Whirlpool directed to local provider. 5/5/20 Fan replaced, drawer clip broken. 5/11/20 Drawer repaired. 5/21/20 Fridge not keeping up, repair company said new compressor needed. 7/6/20 After numerous calls and literally hours on hold with Whirlpool compressor install but still seemed noisy. 9/30/20 Fridge partially cooling, no ice and water dispenser not working. Repair company ordered new evaporator cover and UI panel.10/15/20 Neither the repair company or Whirlpool know when the parts will be delivered. Whirlpool has no record of their being a service call or parts ordered. I talked to one rude, unhelpful and uninformed service rep. After following their instructions and using their recommended warranty provider, they claim not to have the issues in their system and cant be used to determine the repair/replacement of their unit. He indicated, You need 3 major repairs in 30 days to get a replacement fridge. It took them 6 1/2 weeks to repair the compressor. How can it break that many times in 30 days with that bad of service. Nothing is repaired in 30 days. The current rep seems to care and have a working knowledge. She is sending a request to determine when a part might be delivered. She couldnt give any indication of when the part might be delivered to complete the repair. Days? Weeks? Or again Months? An hour and a half on the phone with very little progress. New refrigerator with 3 major repairs and one small one in 9 months. Terrible refrigerator and extremely poor service! Go with another brand.Original Review: Refrigerator new in January 2020. The first issue was an extremely loud fan.It was replaced. While being repaired, service tech broke a tab on the door. (It happens) Another call to replace the tab. During May I notice its not making ice and freezer isnt keeping up. Lose all items in freezer. Now the 4th call on new refrigerator, tech says needs a compressor and orders while at my house. Soon the refrigerator isnt keeping cool. Now 34 days later, still not fixed. Whirlpool service provider blames Whirlpool. Whirlpool says they are shipping compressors but cant exactly say mine is delivered. Apparently, 4 service calls in 5 months and over a month with a totally broken refrigerator is their bar for a good product and service. Neither their approved service provider or Whirlpool care in the least. Awful service. Try another brand!

DO NOT BUY THIS MACHINE. Mine is less than 2 years old. First one month after warranty expired, the clear lid cracked...$350 to replace! Then a few days ago a rusted circuit board came apart and jammed up my washer. This should NEVER happen. I contacted customer service and they told me that they are not covering this problem and that the service call is $175 and cannot estimate the repair cost. They also could not send a repair person out for 5 days. The washer has not been repaired yet so I do not know the entire cost but it will be expensive!

Because the lid was not thoroughly covered, painted and sealed, it began to rust within first year. When I contacted Whirlpool about this - they were not only rude, but will not support quality issues with their products. They basically said they did not care and even acted like a consumer should expect such things! Actually said because its subjected to high moisture levels. WRONG, I do NOT just expect rust. It only formed due to poor quality paint job and was not cured correctly. My Kenmore washer and dryer both, were 25 years old and had zero rust and still functioned when I replaced them with these Whirlpool. Its frustrating that there are no quality, American made products anymore.

I purchased a washing machine and dryer 1 year ago. Since then it has started to get spots on the control panel where you select size, temperature, etc. I also purchased an extended warranty through Home Depot and is still under warranty for 3 years. I was told for a few more days is still under man warranty. I contacted Whirlpool and they said it is not their problem and sounds cosmetic - I think this is unfair being that I spent a lot of money and it has started appearing on the washer and dryer. No one wants to be responsible. I am a consumer who is very careful and have not had any spills or cleaned it with anything.

Purchased I assumed a brand-new electric hot water heater from Lowes. It worked giving us hot water for 5 months then it quit. We called the number they have located on the side of the water heater and they sent 3 references such as plumbers for us to contact because everything they told us to purchase didnt work... so after their references, plumber came out. Instead of him telling us what was wrong why all of a sudden we stopped getting hot water he didnt return our phone call. As a professional that sucks!!! So WHIRLPOOL CUSTOMER SERVICE says the hot water heater that had been working for 5 months wasnt up to code and wasnt wired right and WE need to pay an electrician to connect it right... thats **. The electrician did it correct the first time. Whirlpool just dont want to accept the fact that their equipment is faulty!!! But thats good because I will NEVER purchase anything WHIRLPOOL makes. I dont care if they start making water. I will just quit The hell with that company!!! WHIRLPOOL SUCKS!!! Heres the serial number 1626103174130 and if I had read the neg reviews before I purchased the hot water heater I wouldnt not have done it!!!

We purchase a Whirlpool washer model # WTW5000DWI, SERIAL #C842 43102 ON 10/30/2019 and it has been nothing but a disappointment. We are senior citizens living on a very limit income with several health problems, and cannot go to a washeteria to wash our clothes. We had a washer that lasted over 19 years and when the motor failed I figured it was more practical to purchase a new washer versus repairing this old one. We had a very reputable Whirlpool dealer here and was very helpful and recommended this washer and the price was in our budget! Was that a big mistake, it does not clean the clothes, does not rinse the clothes with using the 2 rinse cycle and still, does not rinse a load of sheets. I bought a large capacity washer so we could wash 2 sheets at a time. Wrong! You cannot get more than a couple inch of water on the Deepwater cycle, so its like washing clothes on a riverbank on rocks, it rubs clothes together. On my wifes good clothes it will cause little balls of fabrics on them, clothes does not smell clean, and if its real dirty clothes, it will not clean or take the stains out. Its water efficient alright, it does not use any water!Its for sale, and I have talked to a lawyer. Whirlpool customer service was no help at all/All they want was to send a dealer to check it out, the only problem if there is nothing wrong with it that will cost me min. of $125.00. Warranty will cover a manufacturing defect, not a design problem which is what this is. I will just go to small claims courts and get my money back and be done with Whirlpool, hell they dont care! I would buy any washer that is cheaper and has an agitator, without a water efficient features and is top loaded model. It does not pay in this world where large manufacturing companies dont care.

There are plenty of reviews on this board already about how the so called AquaLift technology for oven cleaning is completely worthless so I wont repeat what they have already so eloquently described. AquaLift has managed to take us back in time to around 1947 or whenever it was before the old easy off oven cleaner was invented. I purchased the cleaning kit (affinity) as well but it doesnt do much of anything. The only people who might consider purchasing a stove with AquaLift are those who do no roasting or broiling of meat. The oven looks beautiful, so maybe it could be for those who enjoy a show kitchen and prefer takeout.