We have had this range in our new home and in use since May, 2019. The first range had to be returned after its first use due to flaking of the interior walls; a problem the company acknowledged. Since then we have been so unhappy with its ability to maintain the oven temperature. Contrary to the instructions, we calibrated the oven temp and found that it would vary up to 20 degrees lower than the set temp. When set to 350, it would come up to that temp and then cut off until it fell to 330 when it would come back up to 350. That is a great differential noticeable in the time it takes to heat an item and which greatly affects baked goods. A similar lack of consistency in control in the range elements is apparent as well. Now those are major defects. Minor defects are: it is NOT a rapid preheat at all, both lights are on when the switch is engaged even though only one oven is in use, there is no clock function when the timer is in use and the range surface is difficult to clean as it streaks which is visible with the black finish.

GX5FHDXVY04 French door fridge. Ice maker backup issue - which cause water to build up and leak out of fridge. Fix was a known issue with a rubber grommet - $100.00. Fridge stopped blowing cold air - control board - $293. Fridge stopped blowing cold air again! Getting Nowhere with Customer service... Whirlpool used to be a great brand. They have lost me as a customer, and by the looks of this board, Facebook page, I am not alone!

In the first year of my Whirlpool Washing Machine, the motor quit working entirely. Fortunately, the machine was under a 1-year warranty and the motor was replaced by a Whirlpool service technician. My big complaint with this washing machine is this: Even though you select hot water for the wash cycle, the machine has sensors in it that only allow the water to get lukewarm. If it senses the water getting too hot, it adds cold water to bring the wash temperature back down to 78 degrees F. Next time I will do my research and buy a machine that actually allows one to use hot water.

We purchased a Whirlpool Energy Smart Electric Hot Water Heater with a 12-year warranty from Lowes on August 30, 2010. The water heater stopped working and the green light was flashing three times. We contacted Whirlpool since it was less than two years old and they were very rude to us. They told us it was the sensors and we would have to change them out. We waited while they sent the sensors to us. We installed them and it still would not work. It continued to flash three times just as before. We contacted Lowes where we purchased it and they were extremely apologetic and said they would be glad to replace it if we could get an RA number from Whirlpool, but that many others have been having a hard time dealing with Whirlpool. We contacted the rude people at Whirlpool again. They said they were not surprised that the sensors did not fix it. We asked for an RA number so we could get a replacement (after all, it did have a 12-year warranty). Now we were days later with still no hot water. Now this rude technician said it was probably the control board. I asked him if we were going to have to be without hot water until we changed every part on the unit. At this point, we just took the hot water heater out, put it on the curb, and went and purchased a different brand. Whirlpool has lost us as customers for life. If their other products are as horrible as that hot water heater, I wouldnt take any if they paid me to. They were by far the rudest and most hateful people we have ever dealt with and life is too short to be treated that way. I predict they will be out of business in no time with the garbage they are putting out.

On July 30, 2009, we purchased a Whirlpool Gold French door refrigerator with the freezer drawer on the bottom. It was delivered on August 1, 2009. On August 3, 2009, the ice maker and water dispenser stopped working. After three unsuccessful service calls and the installation of various replacement parts, Whirlpool gave up the effort to fix the ice maker and water dispenser and delivered a new replacement refrigerator on October 15, 2009. Todays date is April 14, 2012 and here we go again, the ice maker and water dispenser stopped working. Luckily, I purchased a five year warranty on the unit. However, after reading all of the posts about fire hazard issues and other various issues with Whirlpool refrigerators, well probably go out and buy a new refrigerator and write-off the $2,500 that we spent for this refrigerator as a bad investment. We purchased a Whirlpool refrigerator based upon their reputation of providing sound products. However, based upon this experience, I can guarantee the folks at Whirlpool that our next refrigerator purchase will not be a Whirlpool product or a product of any subsidiary of Whirlpool.

Purchased my Whirlpool dishwasher in 2005 model number GU2500XTPQ3. So it worked for about 10 years and I am fairly happy with that but I have a warning, my control panel shorted out putting out thick black smoke and I was unable to turn off the dishwasher. I had to turn off the switch at the breaker box. If my wife had of been the only one home she would not have known how to turn it off and would have had to call the fire department. I dont know if the short would have led to an actual fire but with that much heat I have to believe it would have. Warning, dont run the dishwasher when no one is home. Hope this helps someone.

I bought the Whirlpool Duet front load washing machine. It was a piece of junk and I bought it 3 years ago. Sounds like a jet taking off during spin cycle and drain.Well, let me tell you, its terrible. It walks out of the space its in during spin all the time and the F Codes. Im done! Just replaced the pump and motor for the drain on the thing and unplugged it several times to reset it. Still is giving me F codes.Im done, I tell you! Done! This has been going on since we bought it!

The dishwasher keypad failed after 1.5 years, went through 2 gas ranges, peeling paint and orange flame in less than a year. Now dealing with the washer, the pump is spitting out white plastic after less than a year. No more Whirlpool in this house.

I purchased a french door refrigerator in March 2013. I purchased the Gold Series because I wanted the best. I have come to the conclusion that Whirlpool does not make a refrigerator with the quality to reflect the Gold Label or any label. My ice maker system created ice dams inside the fresh food area, in the ice bin compartment and allowed water to run into the fresh food area and floor. After four repair visits, I am still dealing with occasional water running down the inside of the ice maker door and into the fresh food area. I contacted Whirlpool and tried to get the defective refrigerator replaced; however, the very rude customer service representative insisted on another repair call by A&E. They scheduled the appointment for a time different than we agreed upon, so at this point I have had to cancel this appointment. I do not know why anyone would want to buy an appliance made by Whirlpool, which includes several other brands.

Purchased this electric range Maytag model YMES8800FZ1 in September 2017. Thought it was just like my old range with self cleaning mode. Beware! Do Not buy this or anything with this new AquaLift self clean technology. That means youre down on your hands and knées, scrubbing. It doesn’t work. Read all the reviews about this new technology. Salesman never informed us. We innocently bought the range with self cleaning, paid lots of money, for crap! Very upset. Will spread the word for all future buyers, pay attention to the self clean mode on what youre buying, cause no one will tell you. Now trying to reach Maytag, but apparently they don’t care.

We purchased our washing machine on October 12, 2011 from Lowes. Our washing machine broke on 04/19/12. We have been dealing with Whirlpool and Advanced since 04/23/12, trying to have our machine repaired. Whirlpool sent A&E out on 05/09/12. A repair person from Advanced has been to our home 3 times, and A&E has been to our home twice already. Advanced came to our house on 04/23/12, 05/07/12 and 05/09/12. A&E came to our house on 05/09/12, and again today, 05/11/12.Finally the repair person from A&E said he needed to order parts which are supposed to be shipped to our house. At this point in time we have very little faith that Whirlpool or A&E will do the right thing and repair our machine. We do not understand how a company like Whirlpool keeps getting away with horrible customer service. Whirlpool is the only company we have found where you cannot get in touch with someone who can resolve your problem. Whirlpool told me today that since a repair person is already trying to resolve our problem, we have no choice but to wait until they repair it.

Purchased this washer in 2009 from Lowes, believing the hype that it was efficient. Since we only needed a Washer at the time, we overpaid (it is more cost effective when you buy both washer and dryer). So we paid $1000.00 for this machine (we purchased the stand as well). After the 1st year, there seemed to be a significant decrease in how fast the washer spun, as the clothes were coming out wetter. I didnt pay much attention, but 2 years later, the machine has a weird problem where it couldnt complete the cycle, and by this time, every time it Spun, the noise was louder and louder.I contact Whirlpool, placed a service call and the Technician came out. $225.00 later, there was a hose that was pinched that was sending a wrong signal to the washer. He fixed that and told me I should get a contract on the machine through Whirlpool since I seemed to be having problems. I purchased the contract, for $300.00, and 2 1/2 weeks later placed another service call, as the noise from the machine was happening every time I did laundry. The service guy came out, indicated that it seemed to be the Agitator, and that he would need to order parts, and that they had a SPECIALIST who only does this type of repair, since they have many! He also indicated that the hose may have crimped due to the movement of the entire agitator!Well, after not hearing from ANYONE for 2 weeks, I called the repair company who told me WHIRLPOOL was supposed to call and let me know that they would NOT fix the machine, as the parts cost more than the Washer, which is now valued at $500.00! No one from WHIRLPOOL EVER CALLED, and I cant understand how a $1000.00 Washing machine touted to be so efficient and environmentally friendly has been THROWN OUT after 3 years!!! And now I am out the $225.00 repair, have no washing machine, $1000.00 down the drain (and I forgot to mention a year later we bought the matching WHIRLPOOL DRYER and OVERPAID) and now have to purchase another machine, which I assure you WONT BE WHIRLPOOL! As most of us have experienced, WASHING MACHINES last for many years! The washer I had before this was over 20 years!!!! So much for efficient and environmentally friendly... The only thing GREEN about this machine is how much of my $$$ has gone to Whirlpool!

I bought a washer from Lowe’s Home Improvement in September 2017, called a couple weeks after the purchase. They sent someone to repair machine. It is still not working. Called Lowe’s back. Was given an 800 number. Talked with someone at this number got nowhere. Was given another 800 number. I am waiting to find out what is going to be done. This is terrible customer service.

I would not buy any Honeywell electronic water heater thermostat. Has failed two times. I have to pay for a new one to be mailed and for repair. A bad product from all the reviews. Honeywell is claiming they do not service it anymore and gave me a Sears telephone number. Servicemen have said it is a crap product and fails all the time.

I have purchased two Whirlpool microwaves since 2007. The first unit lasted 5-1/2 years, the second one lasted only 2-1/2 years. I used it at dinner but several hours later it was dead. After reading other reviews I have decided it would be cheaper and less stressful to get a new one. So Tomorrow I will be purchasing a new microwave which WILL NOT be Whirlpool. I no longer have confidence in any of their products.

Whirlpool makes a beautiful product that does not last. I bought model WRX988SIBM in April 2015. Two years later the compressor is bad and no warranty coverage. Do not buy this model. It does not carry the Whirlpool 2-5 year sealed refrigeration warranty. Its amazing that an appliance that retails over $3K only comes with a 1 year sealed refrigeration warranty when Whirlpool offers it on other models. Be sure you know what your warranty coverage is before you buy any Whirlpool product.

The 12 year warranty, means nothing. The heater only worked for 30 months, and then its upper sensor fault code flashes, and the heater shut down. I called Whirlpool, and they have me use an ohm meter to help troubleshoot the problem. So if you are not handy, you are out of luck. They decided it was my control unit that is defective. They will send me the part free, but I have to pay shipping and installation. What a deal, and what kind of management would dream up of this. The heater is marketed as a 12 year warranty model (only on the tank). Would anyone, having been through this, buy another Whirlpool product?

Looked for the best refrig we could find and it turned out to be a piece of junk! Less than 3 years old, paid 2700$, french doors bottom door freezer. It started making a lot of noise it seem to be coming from freezer. Called Whirlpool, they said to clean coils. We wanted a repair company to come out. They set an appointment for next Tuesday between 12pm and 5pm. Said ok.Was making so much noise, and no longer freezing everything so call said company. Lady was very rude, and said they would not be out on Tuesday but sometime the following week. This would not work for us so called another repair shop, said they would be out. They were here before 6pm. Found out that they have been having this problem, had same type of call already this week. Repair for this problem would be over $1100.00. No thank you! Would just as soon junk this appliance. So very sorry we wasted our money on this.

I was so excited when my husband bought me this as a gift this past year as we are a family of 6 which means lots of laundry. The first few months I assumed it was operator error trying to learn how the new one worked. Well here we are months later googling why it makes my clothes dirtier coming out than they were going. It leaves black linty looking streaks on all my white clothes, both inside and out and leaves white linty looking streaks on my darks, also both inside and outside. It DOES NOT REMOVE PET HAIR AT ALL! If you purchase one, and have long haired pets that shed, expect to invest in some lint remover. Im on my third type in an attempt to save me time. I will say OxiClean laundry detergent seems to be the only detergent that actually cleaned the clothes. Sadly, stores around here stopped selling.And whatever you do, DO NOT USE LAUNDRY PODS. It DOES NOT DISSOLVE THE HOUSING AND LEAVES SLIMY RESIDUE ALL OVER YOUR CLOTHES. I believe this is due to the fact that despite the setting, it uses little no hot water. Which would be great if it actually cleaned your clothes. I could run my clothes under a faucet with no soap and they would cleaner than this pos. Bottom line. Dont waste your money and if you do keep your expectations very low!

The washer works well for the age of it. However, I would say it is not designed as nicely as some of the others I have seen. I found it performed okay doing the wash, but it didnt hold up as well I as I would have liked. Seems cheaply made. The machines plastic parts have stained from rust and seem tinny.

My Whirlpool stove works really well, and it is self cleaning. I have had my present oven/stove combo now for 5 years and had not had one single mishap at all. I am so confident that you will like it I am personally recommending it. It bakes beautifully and if there is a spill or overflow in the oven I just press a button & it cleans itself!

I bought a whirlpool water heater at Lowes 4 months ago, and it has stopped working. I called the customer service number and was treated so unjust. I told them that I had just had it looked at by a plumber and he said that the water heater needed to be replaced, I told the whirlpool represented if what the plumber had just advise me. So I asked them if they could just replace it, the customer service representative told me I had to call another number to have their service people look at it and that wasnt for another 10 days. At which time I asked the representative what was I to do without hot water for 10 days. She told me that they could only schedule it that way. So Im here to tell you all please please please dont ever Buy anything from whirlpool because they will not back it up! I on the other hand just lost $500 and went out and bought a Rheem water heater instead.

Whirlpool microwave 1163XVS - I purchased a new home and a Whirlpool microwave in May 2010. The microwave has all of a sudden stopped heating! Turns on, spins, counts down, lights up, etc., but will not heat. Found this site by trying on my own to detect a possible reason and Im shocked to see these many complaints of the exact problem. Unbelievable, should be class action suit maybe for continuing to take money from consumers for defective product that Whirlpool knows about and appears to not take responsibility. Ive read enough, not even going to call for repair. Im buying another brand and spending more wisely this time. Thanks for the heads up. Shame on Whirlpool.

Whirlpool Double wall-mounted Oven model#WOD51EC7AW05. Have had nothing but problems (at least 7 problems). The 1st one is a potential fire hazard. Porcelain/enamel shattered on bottom interior panel of BOTH ovens in less than 60 days (exposing underlying metal to rust). Cracked in an odd stress-pattern that indicates the metal expanded during heating, and the porcelain finish did not tolerate the expansion. The lower oven had only been used 2X before I noticed the fracture pattern. Obviously faulty design; a manufacturers defect. Whirlpool claims it is cosmetic damage and when porcelain eventually flakes off, they will send me touch-up paint. (If I dent the outside of an appliance with my wheelchair, thats cosmetic damage. Its a manufacturers defect if the damage happens during normal operation. The appliance damaged itself, not the user.)The preheat function does not work on either oven. The oven indicates it is 350-degrees, when it is actually 125-degrees. Repairman says this is normal; ignore the indicator and navigate by store-bought thermometers”. The temperature can vary 50 degrees on either side of the actual setting (thats a 100 degree range!). Between the faulty preheat and the wide range in temperature, it makes it very hard to bake bread or cake.The rest are annoying problems: The timer is a single “beep” (not even very loud), followed by another single beep every minute. This is not much help if you are folding laundry while the cookies bake. The windows have so many dots on them theyre not clear enough to see how the food is cooking (or read the store-bought thermometers) without opening the doors. The oven produces a lot of steam that fogs up the windows (Ive never had this happen, and Im past the half century point). The exhaust fan is loud and it blows hot air into the drawer under the oven (another potential fire hazard). Dont buy this oven. It has several design flaws and Whirlpool does not stand behind their product.

Our less than 3 year old Whirlpool Gold Series 3-door refrigerator (WRF989SDAM00) went up 2 days before Christmas (12/22/17). Service guy looked at it and explained that the compressor was going. We lost food in the freezer since that was the first to lose cooling. We were told the parts alone would be over $600 not including labor, which could be just as much -- the actual repair ticket states a blockage in the cooling lines, needs Sealed System Repair.We understood that trying to repair a Sealed system could create more problems/repairs down the road. In Sep. we had ice build up on the inside of fridge under ice unit, part was a recall under warranty and was replaced, then 2 weeks later they needed to replace an additional part (adapter kit & user interface). It was also making a really loud noise on and off. These parts didnt help completely with the load noise. Ice stated building up again by Thanksgiving but went away before I could call again for service. Dont feel that the replacement parts really took care of that problem. Then the compressor went up.This is a Lemon of a fridge. A real waste of money. So frustrated. We did not purchase an extended warranty so it is basically tough luck for us. We ended up having to shop and then purchase a new fridge (Not Whirlpool and never Whirlpool again) in a few hours and spend money that we did not have budgeted for a big purchase a few days before Christmas. Oh, and there is one more thing, I never realized that a Stainless Steel fridge could RUST, well this one has numerous rust spots on the front door! Junk. I do have images of the rust as well as sound of the noise. I am in if a class action suit is filed!

The Whirlpool range has worked effectively and efficiently for over ten years. We have experienced no problems. It is used several times a day to prepare meals and bake items. The cook top gas burners ignite easily, provide equal flame distribution, and the oven has an air blowing feature that makes cooking and baking much easier. One reason we chose Whirlpool was because this brands stellar performance history, its appearance, and its functionality. Overall, we could not have selected a better appliance for our use. We can unequivocally state that was and still is a solid performer for its cost.

I originally brought this to the attention of Whirlpool on February 27, 2014, and they chose to ignore the matter I raised. I am appalled at their customer service, but then again, customer service has been dead in America for decades now. I purchased a KitchenaAid (Architect Series II, Model KERS807SSS02, Ser. XW4704146) oven in 2009, which included a 5-year extended warranty. The first time I had to use my extended warranty was the first time a pot overboiled and thus overflowed covering the top of my range. Since then, Ive had to have my oven serviced two other times, but resulting from a pot which overflowed on the range.The controls are located in the front, directly below the stove top. There is most definitively a flaw in the design of the model I purchased. It seems quite obvious to me that the design should have included protection from moisture reaching the controls. It is very common for pots to overboil, from time to time, and thus overflow, but this should not cause the controls to malfunction due to seepage. Had I purchased the model that had controls behind the range and controls above the cooking surface, moisture would never reach the controls when a pot overflows. It should not cost hundreds of dollars each time a pot overflows on a range. Had I known that the oven model I purchased had a design flaw that allows moisture to reach the computer controls of the oven, I would have purchased the oven with the controls above the cooking surface.I invested over $2K on this oven because having owned KitchenAid appliances in the past, the KitchenAid brand had historically proven reliable. KitchenAid (or now Whirlpool) can no longer take pride in the quality of their products, most likely relative to the loss of manufacturing jobs in the U.S. Whirlpool ignored me the first time I contacted them on this matter and most recently today when I was told that it was a use matter. Apparently they believe that an overflowed pot is not a common occurrence on a range. I wrote directly to Jeff Fettig, CEO of Whirlpool and he has chosen to ignore me.

The washing machine started leaking and making a noise like a freight train 6 months after purchasing it. We complained in February 2011, but the parts were not available until March 31, 2011. The same problem occurred in September 2011, and we are still waiting for the parts until October 18, 2011. In the mean time, I have been spending hundreds of dollars doing wash at the laundromat.

I bought a Whirlpool water heater in 2009. I paid $588.46 at Lowes. Turns out it is in a class action lawsuit for faulty thermocouple. I was given a coupon from Whirlpool for 2 new thermocouples as part of the class action lawsuit. The thermocouple goes out on it every 1-3 months. You never know when youre going to have a cold shower getting ready for work in the morning. I literally could have bought a new water heater for what Ive spent on thermocouples the last few years. The last two times it went out, I had to replace it twice within 1 day. Im sick of replacing it and have decided to install a new hot water heater. I am disgusted with Whirlpool and tried to contact them about it but have gotten no response. I will never buy another Whirlpool product and would not recommend them to anyone!

Bought a standard 18 cubic foot top mount Whirlpool when moving into my first apt. The refrigerator cost a little over $500.00, is spacious and energy efficient. No ice and water in doors and no chip boards for any controls but still working perfectly. It is now 30 years old and never even serviced. When buying appliances get basic, do the job units and nothing with chip boards. They are still sold today and the fridge I have costs less now.

To be fair to Whirlpool, I have contacted them but have not given them time to respond. I feel so strongly about this issue that I want to get the message about this company product out. About 2 years ago, we purchased a Whirlpool fridge, stove, and dishwasher. I have had so many problems with the stove (WFG540H0AS0) that it has pissed me off, actually. First, the knobs that control the stove top melted. MELTED! We had to replace them to the tune of $30.00 each and there are 5. Why would anyone use knobs that cannot withstand heat on a stove?! News flash, I cook on my stove. Therefore, there will be heat used. Second, the oven keeps shutting off in the middle of cooking my holiday meal. Of course, this made my turkey take much longer than usual. Today, it shut off in the middle of cupcakes. Third, the oven does ignite without turning it on and off multiple times. So we called the repair person who told us to replace the ignition switch for it. This helped for about one month. Then the problem started again. I just emailed Whirlpool and I will call them next business day. I am so disappointed with Whirlpool. I thought they had a good reputation for quality products.

I called customer service because my pilot light would not stay lit on my 2005 Whirlpool water heater. I was told that I needed to install the upgrade kit and that the water heater was malfunctioning because of a lack of air and that it needed to be cleaned at the bottom. I paid for the shipping of the kit although I believe it is called an upgrade or conversion kit versus a recall for this water heater to save money and to get the consumer to pay for replacing defective parts. A certified technician installed the kit but the pilot light would not remain lit. He replaced the thermocouple, although new parts had just been received. This did not help either. The technician and I called customer service, which didnt resolve the issue. I also asked for a manager who would only agree to send out another conversion kit. There are three years remaining on the warranty but I am being told to keep replacing new parts with new parts until it works. That is unacceptable. Also, I was not informed that my problem is a recurring problem with this Whirlpool water heater that I purchased at Lowes.

A little over one year ago, I bought this model from Lowes. Shortly after installation, the ceramic coating on the floor of the bottom oven cracked and shattered. I contacted Lowes... No help whatsoever. I then fought with Whirlpool for weeks until they agreed to replace the unit. Seven months later, the floor of the bottom oven, once again, cracked and shattered. I am now in another dogfight with Whirlpool. This appliance is garbage and Whirlpool does not stand by their product. Do not buy any Double Ovens from Whirlpool. My next step is to organize a class action lawsuit.

I have had no issues with my washing machine. Love the different settings. Washes clothes well. Dryer has minor issues like the drying dial stopped moving so I need to manually turn it off. It’s more of an inconvenience, but for the price it should work.

I bought a dual oven Whirlpool 2 years back. This range keeps breaking knobs that are such a poor quality. I have bought knobs from Whirlpool 7 times already then got PSEG home service and they are tired with the quality itself. Save your money and buy another make! Poor customer service and the worst experience is what I have gained on buying this make. Have old mother at home and this headache only created more issues to help her with cooking.

In January 2016 we ordered a Whirlpool Dishwasher through Home Depot. First, Whirlpool delivered the wrong dishwasher and the installer took my old one away - leaving minimal options to correct the problem quickly. Home Depot did not make the order Model # error but they did compensate for the error. Now, with 18 months of very low use (2 in household - prewashing all the dishes) the pump on the dishwasher is gone. Before posting this review I contacted Whirlpool via email. Two weeks later I had a phone message and I returned the call only to wait for 30 minutes to get through to a customer service agent who could offer absolutely no solutions or compensation for their poor quality product or service. There needs to be a zero on the scale of STARS to reflect Whirlpools overall quality.

My Whirlpool Microwave was installed in my new home by the builder. As write this, my microwave is 1 year 2 months old. Just out of warranty. On this day first the turntable wouldnt stop turning with the door open or closed. One hour after this event, the interior light would not turn off. On half hour after this event...the microwave died.

Whirlpool Washer W10740628A - So disappointed! I have made adjustments for a year trying to get clean clothes from this machine. Compared to my previous machine which wore out, I now use more water because only deep water wash provides enough water; I always choose double rinse because if the machine does not clean, I do not trust it to rinse effectively either. I use more Tide than previously per wash; I use more Clorox than previously per wash. Everything from tea towels to heavily soiled jeans show stains and soils after washing. Instructions say not to spread the item in the washer but allow it to stack on itself, so twisted and tangled wet clothes are the result. I try to soak and scrub all visible dirt before I start the machine now; additionally, I use a mop or plunger or my hands to thoroughly immerse the clothes in the washer, somewhat like my mother did in 1950s. What on earth is this about and what is the buyer supposed to do???

A total loss of money. Does not use enough water to clean clothes. Gets out of balance all the time. Do not buy.

Cabrio Washer WTW660SW2 - For 2 years I have been getting f1. When I talked to Whirlpool they said they were not aware of this problem. Now I have to pay to fix it. Looked online thousands are having the same problem.

I purchased my Cabrio Whirlpool washer 4 years ago and have had problems every since I bought it! Thank goodness I bought the extended warranty! The last two repair bills were over $1000 each! My warranty just ran out and I had it repaired last two months ago! This is not my first complaint! When will they start listening to consumers? This is ridiculous! Now I am faced with the problem of just trashing this washer or spending another $1000 to repair it! Something needs to be done! I am warning all of my friends and family and will post again my problems with this washer on all my social networking sights! Whirlpool needs to take responsibility for their problems! I will never purchase any Whirlpool products ever again if they do not assume responsibility!

I purchased Whirlpool washer in 12/2011. Immediately, I noticed the noise and called service. It was a whistling noise. The clerk told me nothing was in the manual and it would cost $65 to have a tech come out. He advised me to wait until it was louder and more consistent. I called again when it was. Gear case was replaced on 5/2/2012 five months after purchasing the machine. I called Whirlpool again in 5/2013 - same problem. I was told the diagnostic call would be $95, labor which is extended for a major job is $85 and the part would be $290. It would cost $470 to repair as the gear case was guaranteed for only three months. This machine is a lemon since the gear case is now shot again prior to the machine being 1-1/2 yrs. old. I called Whirlpool and spoke to Amy (Esc. Sup.) who advised they would replace the part only. The appointment was scheduled; the tech came, did diagnostics reading a manual and said the gear case is shot. I inquired, Well, you are going to fix it today right? The reply was, Oh no, it has to be ordered and its a two-man job. When I arranged for this appointment, this was clearly explained and what I was expecting, two men and the part to be replaced with them. Now its a five-day wait to get the part and then a scheduling issue when they could do it. This machine is a lemon and Id like to have the machine replaced or my money refunded. This is a runaround, scheduling the appointment and having someone show up with the manual and having no parts and not knowing that it was the part which broke again from previously being replaced.

The burners were very crooked and the pans got burned out right away. They were covered under warranty but since then, they had the same problem with them with the new items. They had the light bulb stuck and couldnt get it out, they came under warranty and now a new light bulb wont work in it. The control top indicator light didnt work so I had that fixed under the warranty, but now it has the same problem and I cant afford to get it fixed and it could be a real safety issue.When it was under warranty, I called about the brown in between the oven door and they said it was cosmetic. It gets worse every time we use the self-cleaning oven like the seal isnt tight. The outside of the door gets brown also when using the self-cleaning oven. We thought we would have this range for a long time as we had a Whirlpool range before which lasted 20 years. I will never buy a Whirlpool product again and we have had a lot of them. e cant afford to buy a new one so we are stuck with this one with all its problems. Whirlpool just gives you the runaround when you call. When they brought the range, the self-cleaning oven part wasnt even hooked up so they had to come back and fix it. I cant believe they dont have more recalls on these. I have only had this for 4 years.

Despite my claim being submitted within the first 4 months of purchase, Whirlpool would not assist in solving our issue. We purchased all major appliances from Whirlpool, to furnish our new home in August 2021. All appliances were white. The top of our gas range began discolouring immediately following the first use. The inside of the four corners immediately began to ware due to heat. I figured Id have time to put my claim in, and thought to see if it got worse. Once I finally had time to deal with the issue, I contacted them only to find out that we only had 30 days from the date of purchase (of which included 3 months of waiting for the products to arrive) to claim the issue, given that it was considered Cosmetic. Easy fix, since theyd simply have to change the top of the stove, but Whirlpool denied our claim. Do not purchase this product, unless youre looking for a sub-standard product and customer service.

Ive had the WDF510PAY dishwasher for 3 years and the circulation pump broke. To be more specific the impeller inside the circulation pump warped and then basically got lodged because it became oblong and then it wouldnt pump water to the spray arms etc. I bought a new pump because the warranty only last a year. The pump cost around 90 bucks. After not even 1 full year this factory replacement pump failed again. I reviewed other Whirlpool dishwashers more expensive and I found they all have this same junky circulation pump. Im not sure of a better dishwasher but I would never recommend a Whirlpool dishwasher again. They also use the same circulation pump in Maytag and many other brands. Whirlpool or whoever designed and sold this pump to Whirlpool should be tracked down and beaten. Simple products like dishwashers should last more than 3 years. The technology is nothing new. A product should last 10 years at least.

Bought this washer 5 days ago!!!! Broke after 4 loads of laundry. Store manager says they will deliver new washer. ERROR CODE LD LONG DRAIN and heavy duty humming sound. Unplugged washer to prevent further damage to washer and reduce risk of electrical fire in home. Consumer affairs wants me to rate my experience - rate my experience on what? Ill give 4 stars dissatisfied here, but field wont let me go more than 2 stars. If its this website they want me to rate I give 2 stars dissatisfied, as for the washer, dole out 7 Benjamins for a product that dont work and you tell me!

The fridge had been leaking just a little for a while until the leak picked up and left a puddle. Turns out this plastic tube connector cracked. Seems a very poorly designed fit that caused the bend in the plastic to rupture. Now the whole tube and what I think is the water inlet valve will need to be replaced.

I purchased a front loading Whirlpool washing machine March 2017. I have need to have the drain pump replaced and the motherboard replaced. Each repair took 30 to 45 days to get parts and service. I would not recommend the washing machine.

3 months after warranty the oven will not stay on. I will stay on for only 20 minutes then it goes out. It clicks but will not come on. I can only use my oven for backing biscuits but cannot bake chicken or meats.

I bought model N40S61-403 gas water heater. I had it installed, and then I came to find out that you cannot common vent with another power vented unit. I contacted Whirlpool 3 times, and got no help, other then it was hooked up wrong. The issue I have is that the water heater’s pilot light puffs out when the furnace kicks on. These 2 items are common vented, in the installation guide. It does not say anything about common venting until page 11, and even then, it is not in bold or highlighted letters. Now the unit’s pilot light is going out without the furnace kicking on. Once again, I got no satisfaction from Whirlpool, other than it was hooked up wrong. I realize that I am the one who is ultimately responsible. Hopefully, they put something on the box, or earlier in the guide to warn novices, such as myself. As for Whirlpool, that will be the last product of theirs that I put in my home, and as soon as possible, I will be removing 3 other appliances during a kitchen remodel, and will replace them with a different brand.

I have read most of the reviews and it seems like I have ALL those problems with my Whirlpool Cabrio, but I also need to add that there is rust around the bleach dispenser and I DONT use bleach. The inside is also rusted, but its not visible until you take a good look inside because its under the white paint but its all around the inside. So I had to stop using the machine because I now realize what was the cause of the damage done to some of our clothes. We all need to get our money back and have this washing machine picked up and thrown away!!!

I used my self cleaning oven feature and the fuse blew, leaving my oven with no electric current. I had to replace the fuse at a cost of almost $300 two months after the one year warranty of the oven expired. The technician suggested I no longer use the self cleaning feature since it will continue to melt the fuse wire. The oven becomes too hot, so I have an oven that I paid for with a feature I cannot use. I would not recommend this product.

My 4- to 5-year-old Whirlpool Cabrio 6300 began to display errors recently. F1 was the 1st error code I encountered. After giving the washer a hard shove and rocking, it began to work properly again... for a while. I noticed on some large loads that I was getting an LD Long Drain error. I could hear the pump running but with little water flow. Eventually, it would time out and give the LD error. A service tech was called and determined that the water pump was defective, although the impellers inside appeared okay and had no foreign objects to impede its spinning. After spending $225 for the service call, the LD error resurfaced about an hour after the tech left. Tonight I got the F1 error again, and once again the washer responded to a sharp rap. The replacement control board, which the F1 error code involves, is $220 plus labor. $440+ for a repair to a $600-$700 washer? Im going to dissect the main control board tomorrow and look for loose or corroded connections. I cant understand why the LD code occurs when I can hear the drain pump running... just very little comes out. Other times it empties like Niagara falls... I cant understand why it works sometimes and fails others. The pump is either on or off. It doesnt have multiple speeds as far as I know. Im not sure what to do next... probably try to re-sell the new pump that was installed to recoup some of the money I paid for a non-working Cabrio. This seems to be a very common occurrence.. Have any class action suits been mentioned? If so, please feel free to contact me.

I had purchased a microwave oven on 18 April 11 and they delivered it to me without accessories. As I was a first time user, I didnt have any idea that the accessories are available with the oven. However, when I came to know after 5 months, I asked them about it and they did not respond to me properly. Even when a Whirlpool engineer visited my residence, he did not ask for the accessories for the demo purpose.The warranty paper has not been filled out by the dealer or the engineer; it is still blank. I tried to put a complaint through the customer care number but they did not respond to me properly.

Bought a Whirlpool dishwasher about 2 years ago. Used it once a day for one year. The bushings already need replacing (maybe $3 to make) and it’s $270 for the part or $280 for whole motor. Do the math. Not impressed.

I bought these products 2 1/2 years ago along with a dishwasher and Microwave, all which are Gold Series. The first month my Microwave broke. Instead of a certain part that they used to use, they now use a Capacitor instead and it broke. The repairman fixed it under warranty, but told me Ill be seeing you again. Then, my oven occasionally says Function not available. Whirlpool wont tell me what the problem might be and they have nothing for troubleshooting this problem in their manual. My only solution is to reset the circuit breaker and then it works for awhile. Now, My refrigerator has ice building up at the bottom of my freezer and leaking all over my floor. I found a Whirlpool bulletin online which explains that this problem is because of a defective part (Grommet) and that they have a replacement part for it and you can get it by calling their customer service department. Why didnt they send out recall notices to their customers?So, on 8/10/2015 and 8/11/2015 I tried getting this new p-trap part, but for two days now Whirlpools computers arent working and they have no other way of looking this stuff up. Very poor customer service and I also waited for a half hour on the phone to be told their computers arent working. How about putting a message on their pre-recorded message letting customers know their computers arent working?

My new refrigerator was purchased in December 2016. The black finish was scratched by the installers wiping off their hand prints. The retailer offered to replace the doors which happened two months later. The black finish scratched IMMEDIATELY while cleaning of the installers fingerprints, using a silk microfiber towel though it looks like the cleaning was done with steel wool pads. I called Whirlpool and the retailer. Whirlpool says to order more replacement doors. Ha! Ha! I have had black appliances since 2000 in another home and there was NEVER a problem cleaning them. I do not recommend WHIRLPOOL because of this problem with the stability of the black finish. I dont have a receipt or order number because the suite of appliances was purchased by the condo association, not me personally. But I can attest to the condition of the marred finish and the ludicrous solution provided by WHIRLPOOL customer service... order more doors. I guess youd have to do that every week after you clean the front of the refrigerator.

Whirlpool washer is junk. Expired I. Less than 4 years. Cost to repair is more than new washer. DO NOT PURCHASE WHIRLPOOL PRODUCTS. Agitator motor burned up without notice. No troubleshooter problem. 2 repairmen suggested I buy new washer.

We have front loaders. Far, far less damaging to the clothing than a top loader with agitator, would never go back to top loader. That comes with a caveat though. There is a difference you may not realize between the two styles. With a front loader comes a little maintenance. You will need to clean the washer periodically. Most all the stores sell the cleaning tablets and no, not all cleaners are created equal. I will only use Affresh after testing most of them. With a front loader there is always some water in the bottom of the drum, even after the cycle ends and even when it looks empty. So if you wash real dirty or smelly things, you’ll want to run an empty cycle to rinse out that leftover water or run with cleaner.In between wash days you’ll need to leave the door open so it doesn’t mold or mildew. The door gasket/seals will show mold and mildew and or you’ll get a mildew smell in your clothing. The only issues we’ve had with these units were the learning curve on front loaders in general and with the dryer we had the water valve for the steam function stick open (after 5 years) but it was due to calcium build up from our well water, not a issue with the machine itself.The dryer lint screen could be better. It is vertical so as the lint builds up during a cycle it drops to the bottom and accumulated at the bottom falling off as you pull it out each time to clean it. The lint catches on a crazy amount of extrusions inside the lint trap which also makes it nearly impossible to get down in and effectively clean all the crap out. One last thing if youre changing from top to front loaders. Buy the peristalsis, they’re expensive but it’s a pain in the butt to get stuff out if you don’t have them. Overall we’ve been very happy with our Whirlpool front loaders and would confidently recommend them to you.

Bought expensive fridge 2009. Now (2015) random very loud rat-tat-tat sounds lasting 5-10 seconds. Very loud. Paid for repairman to evaluate. He said it was probably compressor spring and other springs would probably soon break and would shut down fridge. Said it is very expensive to repair and it would be best to dump the fridge and buy a new one. I called the 800 number located inside the fridge. Jacob at Whirlpool listened to my story and said, Yep, it sounds like the compressor spring and the other springs will likely break. He said he can make me a one-time offer of a full repair of the compressor for only $359.65. We pay Whirlpool and they will have a local guy here come and fix it. We paid by visa.And, via email we get a document that shows we just bought a service contract. This is a surprise to us as we were told were paying to have the compressor repaired. In a few days, a call comes from local repair shop. Guy says, he will come out and check out the noise and see if he can repair our unit. We tell him the noise is intermittent and we cant predict when the noise will occur. We also tell him Jacob from Whirlpool said it was the compressor and that we paid to have it repaired. He says it doesnt sound like it is the compressor and that he cant diagnose the problem if he cant hear the noise. We tell Maytag/Whirlpool via phone we are faxing formal request for refund of our $359.65. Lady from Whirlpool says we, should get a refund in 4-6 weeks. Well, we will see.We are very disappointed in the the short life of our very expensive fridge and we are disgusted with the false and misleading comments made by Jacob of Whirlpool. He told us we were paying for the repair of our compressor and instead we get a stupid service contract. We are in the process of buying a new fridge. And no... It will NOT be a Maytag/Whirlpool!

Have read several reviews on Whirlpool refrigerator. Short and sick. I had my refrigerator less than a month. Broke down, been getting NO satisfaction from Whirlpool whatsoever. I WILL NEVER BUY A WHIRLPOOL APPLIANCES AGAIN. Service is terrible. Months have gone by, and its still sitting in my kitchen broken. They are taking their sweet time fixing it. Garbage. DONT BUY WHIRLPOOL, save yourself the hassles.

I purchased a Whirlpool oven and stove from hhgregg. The refrigerator is at best OK. The stovetop is easily scratched and looks horrendous after just a few months. Cooking controls are far too high for slow cooking. Customer service is terrible. Avoid, purchase another brand. You will be much more satisfied.

Bought the Duet front loader washer and dryer. Nothing but problems and repairs. When I decided to throw in the towel and buy new machines my repair man convinced me to buy Whirlpool again - Cabrio. Said they are amazing. Love them except the holes in my shirts. I bag my delicates but apparently I have to bag everything. So sorry I bought them. There was a day when you could count on Whirlpool. Replacing my crappy Whirlpool gold refrigerator right now too. Hoping LG will be better. Already replaced my Whirlpool dishwasher. Went to Maytag. This company has gone downhill. My mom had these appliances for 20 plus years - I spend thousands and cant get 5 years!!! Dont buy Whirlpool!

Whirlpool Cabrio Washer and Dryer - The washer does not stay balanced even with a very small load (even though advertised can wash King size comforter). Even with a light load, we have to put the dryer on Heavy Duty or Bulky...and usually have to dry a second time. When attempted to contact Whirlpool, no help available. WORST PRODUCT I HAVE EVER PURCHASED... Would not even want to GIVE this set to a friend or family member. DO NOT PURCHASE THIS PRODUCT.

Purchased Whirlpool Cabrio model WTW6400SW washer and dryer 1/7/2007. The matching dryer was dead on arrival and the second dryer motor died within a year. Washer: 1year 2 month the washer motor died. Whirlpool paid for the part and I paid the labor. The following year, the bearing went out and the outer tub was replaced (the bearing is inside the plastic outer tub - bad design. Whirlpool paid for the part and I paid the labor. Feb. 2011 had one of the F errors. Whirlpool repair tech came out as the tub would not drain and it was a wire that had come loose underneath washer - another service call charge. Dec. 20, 2011, I had an error F50. The Whirlpool repair tech came out, verified no clothes or money stuck in the machine. All clear. He called higher level whirlpool tech and they paid parts and labor to replace the main control board and the RPS Sensor. Im single and am not abusing this machine. Like everyone else who posted. I paid close to $1,000 for this washer (not including the dryer) and I have been a faithful Whirlpool customer for 3 generations, but if Whirlpool doesnt offer some kind of compensation/trade in credit to customers who purchased this (knowing that the design is bad/faulty) washer and discontinue this model. This will be my last Whirlpool. I will have lost all faith in Whirlpool. The Whirlpool service tech that I found is op notch. I will miss him if I have to switch brands. Im putting 1 star as I know this machine will not be operational for 9 years which is the minimum that I would expect. If it makes it to 6 years without another service call, it will be a miracle.

Cabrio Whirlpool Washer - Bought this washer from HHGregg in Orange Park, Florida. This washing machine is horrible!! It does not fill the tub with water enough to even cover the clothes. Some of the clothes are not even wet. They just sit in dirty water, no agitation. Then it refills with water and the rinse water is dirty, there is no agitation or movement during the wash cycle. My clothes are stained and dried food and dirt are still on the clothes. My white clothes are now gray. This is the worst machine. I have tried everything. I am now hand washing the clothes and trying to add water to at least cover the clothes but the sensor just drains the extra water out. This machine is less than a year old. There should be a class action lawsuit against Whirlpool. I am not the only one; everyone that has this machine says it is a nightmare.

It is in the mid-range of cost and functions. For a mid-range dishwasher, it has many options, sometimes too many. It does not have rinse and hold. I think its cycles run too long; not always energy efficient (i.e. the simplest one uses the most energy).

Model: Whirlpool Professional FF 32 Elite. Purchase date: 06/2009. Problem: Temperature maintenance issue. The basic need of refrigerator - unable to set/maintain temperature. The cooling system is not working! Poor customer service: Representative charged for visit. The representative is unable to find the root cause! Approximate expense of 4-5k with no guarantee of problem being fixed. Better go for other brands like LG, Samsung.

Whirlpool fridge (model no ETILFKXKS) - I purchased this fridge from a very good dealer (Trail Appliances, Edmonton). Within a year, I had my first of the frozen water drain from top freezer to water pan. Of course, I blamed myself - too much warm food, blah blah. Now this is happening more and more often. The fridge is kept at number 1 of 5 for coldness. All foods are left on counter to cool, but three times over my Christmas holidays this year when I swore I would throw this fridge in the garbage - the drain froze, water all over the fridge, food having to be removed and placed in other peoples fridges, blah blah. Now it did it again this weekend! There are only two living here. I work all day and no one even opens the fridge much and again this happened. Im really sad that such a faulty product (too much insulation hiding the drain pipe behind the fridge and it must be much too small in diameter; otherwise, it wouldnt freeze up). Talking about work. We have two fridges there with 50 people using them all day and they run perfectly for the last 8 years that I have been there. So I think it indicates that my fridge is faulty. Im so sad too because I dont have the money for a new one. I just turned 65 and am about to retire (single mom). You would think that a $1,300 fridge would last longer than 6 years!

Purchased a Whirlpool refrigerator July 29, 2015. Our first service call was August 4, 2015. The units freezer was frosting over, the basket rails were covered in frost, which made it hard to open. Items in freezer containers were covered in frost and labels unreadable. The interior light was frozen shut. Since the first service call we have had 8 service calls with multiple appliance dealers. No one can fix the frost issue. It just keeps recurring. Whirlpool did step up and extend our warranty for another year. In order to schedule a repair we have to call Whirlpool, a 45 minute phone call for an appliance company not of our choice to make the service call. The unit has been removed from our home for repair in dealers shop. Very inconvenient for us to have no refrigerator. Whirlpool has refused to replace the unit, choosing instead to patch-patch-patch one service call at a time. Whirlpool has enjoyed years of an excellent reputation. We are very disappointed. This is no longer true.

We had a Whirlpool washing machine 650s, fully automatic on 28.07.2011 at M/s. Next Showroom Reference bill number 910, Sr no INF **. We had attended, 2 times, a problem with the digital board. After advice from your Whirlpool service person, we had fixed it cutout (make whirlpool), but now, its the same fault with the digital board. Kindly take further action regarding this same problem and sort this out immediately without any further reminder.

We bought a Whirlpool Cabrio in April 2012 and in July 2012, it started giving problems. It wouldnt start. It started humming. We heard money-like jingling noises. It stopped spinning and rinsing clothes. I called for service. No luck with that. So in order to wash, I had to drag the washer to the back door (which ripped up my new floors) hang hose outside for it to finish the load. Well a few months later, that didnt work so the assistant where it was purchased told us to cut the pipe down in the wall. Now we have a big hole in the wall. My floors are ruined and we are out getting another washer. This one is not even a year old. That was a $750 loss.

1st range arrived in June and would not heat to temperature. Sensor and control panel replaced. After 3 techs Whirlpool agreed to replace in September. 6 weeks later new range arrives. Protective film stuck to the lettering and when you try to remove it the lettering comes off. Chunk of enamel missing off inside oven door and defect in the glass cook top. Fast forward to today. THIRD range delivered. Same issue with the protective film and gouge in chalking around cooktop. Leons has been fantastic. They are replacing it with an entire new brand!

We purchased this large 4 door refrigerator in December 2018, from Costco in Florida, having in mind with the 2 years Manufacturing warranties and 2 years of Costco warranties above the manufacturing warranties. We didnt expect any problems for the initial 4 years. Up on delivery some parts of the unit was missing, delivery guys said they will make a report for the missing left drawers and the parts. We did not have any manuals how to setup and use. After we called the customer service they send us the operating manual.We encounter several other problems with this unit and the most recent one to our surprise the warning light to change the water filter was on. We hardly using the water from the fridge because of the having monthly spring water delivery service. We called customer service and after explanation of our concern and following their instruction the light was on. Finally we were told that whether or not using the water filter has to be changed every 6 months and send us the additional service warranty contract which is $411.95 for 3 years. We still have 3 years 4 months remaining from our original warranty.

BFG2F4040T3NIV IS HORRIBLE. This water heater is JUNK. The release valve has released and flooded my basement 3 times in the past 2 years and the recovery time on water is terrible. Whirlpool needs to step up to the plate and refund everyone who purchased one of these. Every review on this unit is horrible. DO NOT PURCHASE a WHIRLPOOL water heater!

Like everyone else here, I had to call a repairman to have a look at my washing machine after 4 years of limited use (only my husband and I). As soon as the repairman looked at it, he told me theyve had so many calls for this particular washer. He ordered a new part for it, but it did not fix the problem. Thankfully we purchased extended warranty and we were credited the full amount + tax. Today I picked up a brand new Maytag washer. Cant wait to try it. Thanks Leons for the great service.

Will never buy another Whirlpool/GE product again. Nothing but problems. Paid $1700 for a Whirlpool/goldstar refrigerator 2 years ago. Problems from the start with slide-out shelf cracking, evaporator fan burnt out within 2 years, digital display cannot read anymore. Now have another problem again - not cooling. Going to the trash. No wonder your stock price have dropped. I would sell off to. Whirlpool/GE have been going down hill for the last 5 years. Maybe more. Cheap products, do reflect, it just a matter of time, I would think you would address these issues in your product line, but it shows your company is all about profits instead of quality of products. Keep going like you are, and you will be bankrupt. Cheap overpriced and nothing but junk in any products you manufacture.

I initially purchased all new Whirlpool products as part of my new home purchase in a Pulte subdivision, June, 2011. My WP microwave failed to heat in 2012 and the replacement of the Magnetron and Inverter and service was covered under warranty (would have cost me $493.51). Sadly, the microwave again failed to heat in 2014. I was so disgusted with this second failure, I decided to live without a MW until January, 2016 when I paid for my second service call and learned, once again, I needed a replacement Magnetron and Inverter, to the tune of $400. Both servicemen told me the 2011 magnetron/ inverter mechanisms were new technology and did not last long. Again, sadly, when I contacted Whirlpool, they would not admit to their defective product line and indicated they could do nothing since I am out of warranty. It is unconscionable that a corporation is not liable for their defective products.

WOW!!! After reading all of these reviews Im wondering why I didnt see these sooner before I bought my POS Whirlpool fridge! Had our fridge a little less than 2 years and the freezer just does not keep anything cold anymore. Stopped making ice and everything in the freezer started to defrost. We noticed this one day when our ice cream was runny... Yuck! So we looked around online for troubleshooting. We took out the drawers and the back panel... There was a huge chunk of ice right before the coils. The coils themselves were not frosty and we thought that might be a problem, but we didnt know. So we thought this might be the problem. So we took a hairdryer and melted the big chunk of ice. After we did that we then noticed the coils started getting frosty again but not consistently or evenly across all of the coils. I dont know if this is good or not??? So now Im going to purchase a thermometer and see if the actual inside of the freezer is getting up to the correct temp. After reading all of these reviews on here Im thinking Im screwed!!! We also called Whirlpool and they basically said... oh well not our problem. WHAT A ** COMPANY! I will never buy another Whirlpool product again... Even if they offered me a free one I dont think I would take it.

Purchased side-by-side model fridge, and within a month, the ice-maker froze up. Within a year, the relay switch failed, and caused the compressor to fail. What a lemon. Also, the clear bins in the door of the fridge side, have all cracked. Whirlpool says it is a cosmetic issue, but I think it is hazard and a material processing failure during their manufacturing process. They obviously would not cover any cosmetic issues under the warranty.I was one of the lucky ones, at this point, as the repairs were under warranty (expensive compressor, only by one week), had to buy an extended warranty to cover me in the future. I was only out the cost of extended warranty, and a fridge full of food. Lucky me. Customer service is worthless for any issues. I dont think Ill buy another Whirlpool product again. Buyers beware.

Bought this model from Bad Boy in 2006 and just after the warranty ended the problems began. We kept getting the F1 error code so with a little internet research we found it was a known problem with Whirlpool. I contacted them and was told they knew nothing about this issue being nationwide, however I emailed them copies of the complaints and responses. They sent out a technician who had to replace the motherboard free of charge. Next issue was a loud noise coming from washer sounding like a jet plane taking off. Hubby ripped machine apart to find the bearings blown apart and in tiny pieces. We ordered new ones and also found that when the new ones arrived they came with a tube of grease and a sealer to use so water would not get in later and cause more problems. Funny there was no sealer on the original bearings.Next the lid lock finally failed, ordered a new one but did NOT install it back into the machine, now it sits beside the machine. In case it fails again we will have total access to the laundry this time. Finally the UL error code keeps coming up. I refuse to put any more money into this machine again so I am allowing hubby to fix it if he chooses, whichever way he wants as long as no money is involved. So right now we have bungee cords holding the suspension rods tight to help with the uneven load code coming up all the time. Personal thoughts - DO NOT BUY WHIRLPOOL washer/dryers. They are crap and the company just does not care and they try to lie their way out of repairs if people have not done their homework.

We own a Whirlpool microwave hood combination. The door started cracking where the handle attaches. Ordered a new door and installed in July 2017. 18 months in the door and the handle have both started to crack again. This seems to be a problem with Whirlpool microwaves but they wont stand behind their product. Theyll send someone out to replace it for $$$$ but they wont admit they have a flawed product. One year warranty - no exceptions. Will have to replace the microwave and it wont be Whirlpool!

Whirlpool microwave came with my new condo, and its as aesthetically pleasing as it is functional. Very easy to use, sounds are not annoying (as my last microwave was) and heats food quickly and evenly, as needed.

The first day I set foot in IKEA changed my life, innovative and sensible and affordable. Some years later I had the opportunity to remodel a kitchen and I immediately thought of IKEA. I used their online planner, researched the appliances and knew that they were made by Whirlpool and that they offered a kitchen package discount if I bought 3 or more appliances with all the cabinetry. So I hurriedly designed the entire kitchen from top to bottom with IKEA.Included in the design was my center piece, my 5 burner Praktfull Pro Gas/Convection oven range with stainless steel backsplash and top of the line hood fan, basically a thing of beauty! I loved it and I visited the store several times to look at it. I finally bought everything, and installed it. Absolutely the most beautiful kitchen in the world.We have a historic building and were on several historic tours, interviewed for the newspaper, our kitchen was the highlight of the tour. My gas range drew oooos and awwws. The range is an exceptional appliance, beautiful and amazingly efficient, easy to clean…I was in love. Then one day it happened, the love affair was quickly over, devastatingly over. The door fell off the oven and the hinge broke! Yes you heard me right, it fell off, but that is not the worst part. It appears that not only are there no parts to fix it… there IS no fix for it, period. The door fell off because it had been glued on!!! Yes glued on. Whirlpool and IKEA had actually manufactured an appliance that failed in less than 4 years of use and no apparent intention to ever provide service or parts for it. This is criminal and they should be fined for their neglect of the customer, their calculated malfeasance and fraud to the customer.So my beautiful kitchen has a big black angry cavity in it and now I must try to find a new range that will fit in the opening left by this piece of junk and also pay probably over $2,000 to $4,000 for it. Most of all I am heart broken, mad and distrustful of anything IKEA in the future. Oh and by the way, my entire house is IKEA, my living room, my patio, my bedroom (s), my library, my office! Ive spent thousands and thousands of dollars at IKEA. No more! THE FINAL INSULT: Ironically…. my kitchen was featured on the IKEA website!!!

My Whirlpool refrigerator model #ED5FHEXV001, serial #HR0248 - I have spoken to a couple of reps on the phone. I am very dissatisfied because it was like one rep I spoke with on the telephone advised me to buy an extended warranty and at that time, the company would consider alternative ways to deal with this complaint and perhaps replace the refrigerator. I did not want to pay an additional $100 for a warranty, unless the company would guarantee me a solution, preferably my money back. I did not really believe the warranty would help me after the warranty was expired. I would still have the same problem and I feel that in the event after the extra warranty expired, the company would tell me I should have kept the coils clean, which is my complaint. There is no way to keep the coils clean. I guess blowing out the residue, then all that residue material would end up all in my house. Also, very important, there have been 3-4 technicians to my house the first year. I was told various things to do, such as adjust the refrigerator to a lower setting and freezer to a little higher setting. One tech actually replaced a part? The second tech said he would clean the coils. The last tech told me the problem was my coils had to stay clean. My question is, how the heck is that possible with the coils on the bottom of the fridge and susceptible to a lot of dust and dirt, unless I move my fridge everyday? Most people do not expect to have to clean under the fridge each day and the coils would still be dirty anyway. It is very dumb that the coils are not on the back of the fridge. With the fridge coils on the back, I have never experienced this problem. Please advise what my next step would be. Thank you.

Back in the day GE appliances were made to last and last - the only one I have found close is Whirlpool. They have style, dependability and long lasting products. My washer machine has a ton of features and I didnt pay more for any of them.

I purchased a Whirlpool Cabrio top loading machine approx 3 yrs. ago. When I first bought it, the machine was super quiet... loved it. I loved the capacity of it. About a yr ago I noticed it started making all kinds of noise, we cant have a conversation downstairs because its so loud. Turns out the bearings are broken. The technician was nice enough to explain to me that its a common problem with those machines. However, Whirlpool is not willing to stand by their product and repair it free of charge. Any other product would of been recalled and repaired. That goes for cars, baby products, and so on. But not Whirlpool, I called and spoke to Andrea in Michigan who told me that there is nothing that they are willing to do. After reading the other reviews and their terrible one star average rating it doesnt surprise me. Shame on me for not researching this product before buying. I hope this saves someone else from making the same mistake. In case your wondering, it cost me $117.00 to have the tech look at the machine. The labor would of cost $125.00 and the part is $251.00........

I bought the HE Whirlpool Cabrio 2 years ago. It has all the bells and whistles, fancy cycles, etc. but doesnt clean ANYTHING. I have to wash three times to get things clean... So much for energy efficiency. It also gets out of balance with larger loads. What a waste of money and time.

We purchased a new Whirlpool washer in March 2010. Yesterday, 2/19/12, the washer stopped working. We called a repairman who checked the machine and told us the motor needs to be replaced. We called Whirlpool today, 2/20/12, and were told by their customer service department that since we did not have an extended warranty. We told them that we believe the motor should last more than 2 years. Their response was that if the motor lasted more than a year that was all they cared about. The only thing they would do is replace the motor if we gave them $299.00. I think it is very clear that Whirlpool knows it makes inferior products as they fail to stand behind what they make. I will never buy another Whirlpool product and would advise anyone who is looking for a washer to buy something other than Whirlpool.

Changing the filter is difficult & expensive. And where has the old fashioned service gone. New refrigerator and would have to pay for service. This happened when I bought the refrigerator a couple years ago. I do not think this should be the standard for a new refrigerator.

I bought a compact washing machine and 4 months later it broke, needed a CCU board. To make a long story short now the machine is 7 months old and still broke. Whirlpool cant locate a part for it nor do they want to replace it. I think its time to get a Lawyer involved. Ive been calling for weeks now and have gotten nothing but the run around from all very Rude employees. Im turning this over to a lawyer. Im done dealing with Whirlpool. For a large corp Im very aggravated and severely disappointed with them. Wish I never bought their appliances. NEVER AGAIN.

Bought a Whirlpool French door refrigerator in March 2014 and have had to have it serviced 4 times now - all for the same issue. We get frost in the refrigerator (not the freezer, the refrigerator). The same parts keep being replaced but they are all defective. This last time the service tech said he contacted Whirlpool and they had a redesigned part that should take care of it. Within 3 days of the new part being installed the frost is back. The other issue is the loud noise of the compressor. We have had multiple Whirlpool products through the years, but this is the last.

I purchased it in 2011 for $1100 Canadian. Smooth glass top and true convection. The controls were easy to use, and understand. What bothered me was that it stopped working just after the warranty ran out. I did my research, and found that the newer ranges that have the controls on top at the back have issues with the motherboard overheating, and causing this problem. I did speak to Whirlpool customer service, and managed to convince them to supply the replacement part at no cost. I paid my local dealer to install it. This repair lasted for just over 1 year. Same problem again.This time I could not convince Whirlpool to supply the part. FYI The part in question is the controller. Essentially a motherboard. All the controls are operated through this small computer. It is the only replacement part that costs over $100. Last I checked it was around $450 Canadian. The reason for the fault is overheating. According to the tech that fixed it the first time, it is the most common problem with this style of range. I find this concerning considering the only thing a range does is create heat!Keep in mind that you are virtually held over a barrel. There are only two companies that market their products under multiple names adding up to over 80% of the appliances on the market. They battle for that market by offering more bells and whistles, and less quality. The Range I replaced four years ago was 20 years old. I just replaced my Whirlpool 3 months ago. I went outside of the 80%, and bought a Samsung. Im rolling the dice, and went with induction top. My theory is it will produce less heat because it just heats the pot, not the stove top.Low quality drives me nuts. I want fewer bells and whistles, and more long lasting reliability. I should be able to go my lifetime and only buy two or three ranges. We really like the induction top. It works fast, and doesnt produce too much excess heat. Dual zone oven is a good idea. We werent looking for it, but there was a deal on. The dual zone induction range was only $50 more than the regular one beside it. Now my wife uses it all the time. She will have cookies in one zone, and a casserole for supper in the other. True convection is the other must have. It does a great job cooking everything evenly.

The buttons that turns on the burners and oven turn on with a very light touch and start leaking gas and sometimes light. Its very dangerous and has done this since We got it new from Lowes. I wonder if there was a recall on this model or if lots of other customers have had the same trouble. Model #WFG524SLAS O Ser. # R20910336 We have had this stove about two years and My wife has kept after Me to report it , but I never realized how dangerous it really was until now. The previous stove We had you had to push in on the buttons and then turn them before they would light. Thank You.

Thermocouple failure on a Whirlpool water heater - We are having trouble finding the part to replace it because the thermocouple is threaded left-handed, and Lowes does not seem to have any replacements in stock locally. Meanwhile my tenants are without hot water, and my repair bill is escalating due to labor.

The machine is reliable, does not take forever to do a load, it is relatively quiet. It has sufficient options depending on the size of the load. Additional options are time setting, choice of warm, cold or warm/cold water settings. On light and medium loads it extracts almost all of the water; on heavier loads an extra dry spin does the job. In all the years that we have had it, it has required only one service call. The maintenance man told us that this model is the best in a series and he recommends that we hang on to it for as long as possible. We're very happy with it.

We bought a Cabrio washer less than three years ago. I have never felt that it got my clothes clean. The washer recently stopped spinning and agitating. We were told by a very experienced repair technician today that the gear case and bearings in the tub need to be replaced at a cost of $700.00. Needless to say, I am very upset. I called the Whirlpool Company and after being on hold for almost 15 minutes, I was told that my washer is too old to qualify for any help with repair cost or part replacement. My household consists of two adults. We do on average three loads a week. This is an inferior appliance and after this experience I will never purchase another Whirlpool product.

My 3 year old water heater failed and the service line would send us the part but the install was my responsibility. Shipping was free but would take 3-5 BUSINESS days. Whole has a week to wait with no hot water, $35 for expedited shipping (which took 2 days), $175 for the plumber (authorized by Lowes (1star also) for installs). 2 days later the unit is cold again... Plumber comes back, plays with wiring and gets it fired up again. Says if there is a problem again to refer the techs to the plumbers office for new tank. Well now Whirlpool says they will only take the word of their own plumber AUTHORIZED HEATING 24 hours wait for a service call. You will be the 1st job Wednesday morning. Wednesday 930 call from AH we are backed up. Hope to be there between 1 and 4 pm. How did you get backed up if I was 1st job? Never again will I buy Whirlpool and nothing from Lowes as well. Still no hot water day 3 second time in 2 months.

Purchased Whirlpool Dishwasher 1 year ago. I use the Dishwasher once a week. When the Dishwasher was originally installed, immediately I noticed when dishes were placed the racks, there is an annoying squeaking sound. I am not exaggerating but the noise can be heard from my sidewalk outside! I called Whirlpool and a technician was sent to my residence. There is nothing wrong with your Dishwasher. I was told to Grease the racks. One year later I still have the same issue! I placed the phone near the Dishwasher to have the Customer Service Rep hear the Loud Squeaking and to no avail. I will never ever buy another product from Whirlpool. Now the latch will not close to the door! I rarely use this appliance, only placing dishes and utensils. No Pots and Pans!!!!! This is going to be another huge bill I will be responsible for paying and I dont feel it is of my own doing. It seems to be apparent that Whirlpool does not stand by their products!!!! I am sure they are aware of all these issues, customers are complaining and nothing seems to be done from reading some of these posts. I am wondering why they are still in business.

My house was built in 2004, therefore the Whirlpool water heater was installed in June 2004. The water heater broke down (It flooded my garage) in 2007. I didnt have to pay for the water heater at Lowes (It was under Warranty), but I had to pay for the delivery and labor. Now, I had to call customer service, because the Whirlpool water heater installed in 2007 has problems too. The pilot light would not stay lit. I have to pay a certified technician $180, just to come to my house to fix this problem, when this is a recurring problem, with this Whirlpool water heater that was purchased at Lowes. (The heater has a six-year warranty. Not sure what this means if the product is defective to begin with). Im very disappointed with this product. It has too many problems, and I have to pay for a defective product. I would stay away from Whirlpool if I could.