Bought a new set of Whirlpool Cabrio Platinum tin replace my Maytag that had finally died. I believe this is the worst set Ive ever owned. It wasnt inexpensive but its cheaply built. Cant wash a set of sheets without it getting out of balance, even if you carefully place them in the washer as they recommend. They knock up no matter what you do. The dryer is gas and my clothes still have to be turned back on for more time that should take. We are talking about over an hour. Ive had them just a few months but Ive had it. I want my washer and dryer to just do their jobs like you expect. Im selling them or donating them but whichever they are out of here. Whirlpool, I am ashamed of you. Putting out such a poorly made washer and dryer. Instead of the name Platinum. They should be named Salvage. Never again Whirlpool. Never Again!!!

I have purchased 2 Ikea/Whirlpool ovens in 2011 from Ikea in Canada. I have used the self clean feature on both ovens and both ovens quit completely and the doors stayed locked. This problem is discussed hundreds of times on the internet for Whirlpool, Ikea and Kitchen Aid ovens. Since they are all made by Whirlpool they are all very similar or exactly the same in some cases, as is the problem. I have discussed this with Ikea and they have said they didnt know about the problem but would help to get it fixed to my satisfaction. I have had Whirlpool authorized service repair both ovens but after trying the self clean feature again, same problem.During one of my conversations with an Ikea representative on the phone, she contacted Whirlpool and was told that if the oven was repaired 3 times and deemed by the service technician as unrepairable, Whirlpool would do a buyback. In other words according to Ikea, Whirlpool would take the oven and pay me what I paid for the oven. Well after contacting the authorized service dept (not Whirlpool itself) for the third time, they did some investigation with Whirlpool about the problem. To his and my amazement, Whirlpool has come up with a fix as of October 2013. The technician ordered the new kit and installed it in both ovens. I have since tried the self clean in one oven and this time it worked. For the information of others, Whirlpool has the kit and in it is an instruction sheet with pictures as to how to replace and install all the parts in the kit.I watched the installation, quite a process. From the instruction sheet there is a number on it. Here is the number - w10625529 rev. A 10/13. This is an instruction sheet for Ikea TOD (thermal overload device) service kit. I have looked at many of the service parts diagrams on the internet for many different current models of Ikea, Whirlpool and Kitchen Aid ovens and in most cases almost all the inside parts are the same or very very similar which leads me to the conclusion that this service kit may work in most of these ovens to correct the same problem, but I suggest checking with the appropriate service people before taking my word for it. My observation is that the kit moves the TOD off the top of the metal plate of the oven and onto a new bracket which the tech thought it was to get it further away from heat (this Im not sure of since Im not an expert). He also suggested that this kit may also be designed to allow more air flow around the oven.My only concern after having the self clean feature finally work is the heat produced inside the kitchen cabinet in which the oven is installed. Approximately an hour and a half after turning the self clean on, I felt the side of the cabinet between it and the fridge (open space), and at one area of the wood cabinet I could not hold my hand on the cabinet as it was too very hot. I will be checking the inside of the cabinet for signs of excess heat and if I see any evidence, I will again call the service people. Since the elements were not on when I checked this, I assume the self clean had finished the heat cycle and was in the process of cooling down. When I test the other oven, I will make sure the elements are still on as I can see them thru the glass door. When I checked the temperature of the outside wood cabinet using a laser thermometer, the outside wood registered 64 degrees C or 142 F approximately. Not sure what the inside temperature was as the oven was still in place. Hopefully I will not get a higher reading when the self clean is at its maximum temperature in the cleaning cycle. Will the oven create any problems in the future for the cabinet, I hope not but time will tell. For clarification, the cabinets were built by a kitchen cabinet company using the instruction sheet that came with the ovens. I hope some of this will be of help to some of the hundreds of people who have posted this very same problem on the internet. When you have paid for an appliance you wanted because of the features it came with, it should provide you with what you paid for and not constantly break down. Im lucky as they came with a 5-year warranty so it hasnt cost me anything yet and hopefully wont in the future. Good luck to all in getting this resolved for all of you.

Overall??? Ive owned this Whirlpool side-by-side refrigerator for a year now. Love it except for semiannual cost to replace the filter. My brother recently installed the same model in his motorcoach. Yes I recommend this appliance.???

Their water heater is the worst ever! I will never buy another Whirlpool product. We purchased our water heater on January 17, 2010. We had to have the entire electronic system replaced in August 2011, including the lower element, control unit, thermisol, and electronic. Now, just a few short months later, the system is not working again, plus, the containment unit failed, flooding our basement. When we called Whirlpool, we were treated callously and rudely. Now, we have to pay to have the old unit removed, and a new one installed (they told us to throw it in our trunk and return it to Lowes, as if). Why did we pay to have this warranty when both the product, and the warranty are junk? Never, ever again! While Im at it, I should add that our range, and refrigerator are also made by Whirlpool, and those too, are pieces of junk. I guess were bucking up, and scheduling a new installation. If there are any further problems, I will be contacting an attorney.

I felt compelled to write this review, to sum it up NEVER buy ANY Whirlpool, KitchenAid etc brand. Nothing but the worst experience, it all started with a 5 year old Whirlpool fridge that stopped cooling, I called and they said they could send someone for like 200$ and that it does not guarantee it will be fixed. So I called an independent and he tried to refill the freon, but it was leaking behind the fridge in a section you cannot access because they want you to buy another one, so 5 year old fridge in the garbage and now to top it off, a KitchenAid knife set that is barely used, one of the big knives broke cutting a fruit, and good luck in any circumstance getting any customer service. SO NEVER AGAIN, TRUST ME AND PUT YOUR MONEY ELSEWHERE ON ANY OTHER COMPANY.

I love my Whirlpool gas stove and oven. We opted for the convection feature as we are a family of 7 and often need multiple items in the oven. This was a very useful detail. I didnt know I needed that. I now cant go without!

Own Whirlpool GB2FHDXWS04 refrigerator for 14 months. From the beginning, the ice maker made gross tasting ice and never got better (had to start buying ice). Then a smell started coming from the fridge every time the fan came on. We called before the warranty was up and talked to Whirlpool, and they said that we must have put something smelly in the fridge that caused the plastic to absorb the smell (which we didnt). They told us to put baking soda in and change it everyday. No change. They kept telling us there is no way it could be giving off a smell for any other reason and if they sent a tech out, we would have to pay for it. Trying to intimidate us until the warranty was up. Then after a month or so, the bottom mount freezer starts leaking water all over the wood floors every 3 days. At first we turned off the water line, but then realized it is coming when the freezer defrosts. One good thing, the freezer, from the beginning, knocked really loud and now that its leaking it doesnt knock. We spent $1,200 just over a year ago and will probably have to go purchase a new one now. I will tell you it will never be another Whirlpool product. Whirlpool has not apologized or done anything but say, Now your warranty is up, you should have bought the extended warranty. Great customer care! With all these same complaints, you would think Whirlpool would figure the problem is their inferior product (which they know) and actually take responsibility.

I bought a Whirlpool refrigerator in 2007 from a recommendation from my repairman. He told me that most refrigerators last about five years. I cant believe after five years I will have to buy another refrigerator. I know someone that has a refrigerator that is 50 years old. Cant any refrigerator makers make any appliances that last? With all the technology we have nowadays, it seems like you could. You just want the public to spend more money on repairs or a appliances. Hope you buy the product you sell! Looking forward for a reply.

We have had our Whirlpool Cabrio washer for quite a few years. I agree that the machine is a piece of garbage. Every load is unbalanced. You have to stand there when the spin cycle starts, with your finger on the pause button, so you can rebalance the load, which is no easy task. My 80 minute whitest whites cycle took 2 1/2 hours to complete. Thank goodness I started the load at 5:30am. I hate this washer and anytime I am in an appliance store and see someone looking at it, I inform them it is a piece of junk. I havent contacted Whirlpool because I know they wont help with any issues were having.

I bought this Whirlpool dishwasher 3 years ago and the first time I used it I was completely blown away. We can run it at night and never hear it. The first time I turned it on I had to go back and check it to make sure it was on.

Remodeling kitchen. On Sept. 2017, bought new Whirlpool microwave mod# WMH5352OCS, Actually put to use on Jan. 2017, by Nov. 2017 started getting open door errors by late Dec, 2017 completely quit working. From what I have been reading they barely make it thru the warranty period. Maybe they will run longer if one doesnt register the appliance. Especially with the crappy service for the ones that tried to have it repaired under warranty. I purchased it at Costco online, my next complaint will be to Costco, hopefully theyve gotten more complaints and pressure Whirlpool to stand by their product, NO MORE WHIRLPOOL FOR ME EITHER.

Originally installed early 2007, the very expensive unit went crazy after about 14 months, with random beeping noises, and non-response to keyboard entry. Sometimes unplugging the unit worked. When unplugging no longer worked, the unit was repaired by replacing the keyboard logic boards only to fail again the same way.about a year later. It appeared the heat or steam from the cooktop below the microwave was causing the failures, so we became careful to ensure the fan was on. Last week, after boiling some water, the unit failed again, with error code F2H2, the keyboard error. Didnt Whirlpool expect the microwave to survive heat or steam from the stove/cooktop below? Overall, the unit is great when it works. Unfortunately due to the large size of the 2 cu ft unit, only an identical unit will fit. Im skeptical of replacing my broken unit with another Whirlpool Velos unless this keyboard problem has been fixed in new units. Anybody know if Whirlpool has fixed this problem?

My Whirlpool Cabrio Washer is only 4 years old. I have had balancing & spin issues since day one. Thought it was just me. Constantly had to drain and spin after rebalancing. Now 10 days ago it cost me $250 to have it fixed. The aqcuator (?) Went. It wouldnt spin out. Now 10 days later it stops again. The appliance guy reads code. F7E7. He tells me the bearings are no good. Will cost another $400 and they need some special tool to fix it. IM DONE. My last set was 15 years old. The price is ridiculous and quality not worth what this triple capacity set cost.

This dishwasher is noisy, it does not get the dishes clean, and anything that is remotely lightweight gets thrown all over. This must be one of Whirlpools cheapest models as I have had other Whirlpool products and they were fine.

I bought a counter-depth French door refrigerator for our new build. I had to wait 6 months for delivery since it was on backorder. When it arrived a door was bent. Lowes replaced it with a door that had a leaky ice maker. Ice and puddles of water intermittently appear on our new wood floor. Whirlpools technician told us WE would be charged if they couldnt find the problem. Whirlpool rep confirmed. Also the manufacturer warranty began at purchase date instead of delivery date.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

I also have a side-by-side Whirlpool Gold Fridge purchased from Lowes Retail Store, and I paid $1,480.00 for it. It is now 4 years old and I just noticed large cracks on right, inside part of the fridge. I called Whirlpool and got a runaround. Some lame guy said, Sorry, nothing we can do for you.When are people going to stand up for their rights and fight for their bucks? They havent heard the last of me but I will put this on the back of my truck with a nice sign on it for thousands to see. If anyone else has had this problem email me at ** and lets talk. I will never buy any Whirlpool items ever, ever again! Buyers beware! I also hold Lowes Retail Store responsible for this. They should research and stand behind what they sell, they are no better than Whirlpool!

Whirlpool Energy Smart Residential Electric Water Heater - On top of this water heater is a junction box. If it goes out, so does the water heater. I am on my fourth junction box, at my expense on three of them plus the electricians bill times two. They finally sent me one free!

Just bought this washer, its making a lot of noise, sounds like something is grinding (metal, gears, etc). I thought Whirlpool was suppose to be good. I just had my Maytag go out after 18 years of service, thought about getting another Maytag but found out Whirlpool makes those. As many complaint as I see, seems there needs to be a class action lawsuit against Whirlpool for shoddy work.

Our Whirlpool Duet front loader washer developed a mildew smell and started making a horrible banging noise on the spin cycle. We had a service man come out and the concrete weight had broken in half. He said this was not uncommon. I just did a Google search and apparently this is a true factory defect. Luckily we had purchased an extended warranty. I always thought Whirlpool was a premium brand but after this experience I will never buy another washer from them. They should do a product recall.

On July 19, I was forced to buy a new washer. Bought a Frigidaire which, when connected to the water supply, started immediately dumping water into the drum. Sent this defective washer back to the retailer and chose a new Whirlpool. O-M-I-G-O-S-H! It was delivered on 25 July and despite having 4 temperature settings, it only worked on either hot or cold AND you could never tell what temperature was going to be chosen by this computerized wonder. I repeatedly called Customer Support and received three different answers on what temperature was considered warm. The answers ranged from 65 to 102 degrees. Also, you could open the lid when the water was running in, which washers are no longer supposed to do. Whirlpool then arranged for A & D Service to come and repair my NEW washer and scheduled an appointment for a week later. I was forced to call that company to find out if they were even coming. When they did not show as promised, I cancelled the appointment and called Whirlpool to ask for another service company. They then scheduled me for two weeks later (now August 30th). The guy did come and told me there was user error - I had used too much soap as this was an HE washer. I asked him to show me where on the appliance and in the owners manual that it stated the washer was an HE. He couldnt find it either and said he would replace the computer and the door lock because his computer found that the washer was hit and miss on anything it was set on. At any rate, it is a little over a week later and I have heard nothing from the repairman and, of course, no follow-up from Whirlpool. Do not make the mistake of buying any Whirlpool product, and that now encompasses names such as Maytag, Amana, Jenn-Air, Kitchen-Aid and many more if you want to be assured of a quality product and excellent customer service. What if this had been a refrigerator? The whole debacle has been a nightmare. Wish I had bought a GE!

My landlord purchased a new Amana washer (NTW4605EW0) Labor Day weekend 2015. It started having issues in the spring, so we went through the process of utilizing the manufacturers warranty. Apparently, Amana, part of Whirlpool, requires 5 attempts at repairing the machines before replacing. Okay, so starting in June 2016, we arranged service appointments 5 times and replaced 1 part, then another, 4 times. Clearly, that part is defunct. Right? Fast forward to September and then into October. Get a new washer, and not the one I preferred. We got the Whirlpool WTW4816FW1. Before the installers leave, we are having the SAME issue. Stops midcycle, doesnt finish cycle, sometimes stops while filling, or while full, or kid wash, or mid drain... But now with the new washer, the drain and spin cycle thinks it should FILL instead of drain... and Whirlpool said they would get someone out the next day, a promise they cannot keep because they dont supply the repair guy, they source with local companies. So, the company ordered 3 parts... That could be the problem. And 4 days later, 2 parts are on freaking BACK ORDER. Parts arrive. All new parts replaced. Machine still doesnt work. Outlet tested by us and them and it is fine. The techs think there is some kind of RF interference. Turn off sensor light, which is on the same wall, unplug power to wifi router (which outdates the washer). Still, doesnt work.I have spent half my week, every week, since June, restarting my washer, unplugging the damn thing, waiting, and waiting, trying again and again and again to wash 2 loads of laundry a week... Literally takes a week until the damn thing does its job. Whirlpool is sent us a replacement washer. Can you guess what happened the first time we started it? SAME ISSUE. Cycle will not complete. Sometimes it dies before it even fills. Sometimes it dies while filling. Sometimes, it will fill and fill and drain and fill and fill and drain and... never stop filling. Or, the fun one, the drain and spin cycle thinks it is suppose to fill. Continuously. And then, suddenly, after unplugging it for 1 hr, or 24, or 72 hrs, it will work fine for 1-7 cycles. Nothing is consistent except that it doesnt work consistently. HAS ANYONE HAD THIS MUCH TROUBLE???

Whirlpool Gas Range WFG540H0es - Purchased 2 months ago. After 2 weeks there was a spill. The black burner caps are powder coated. After cooling we washed it with dish detergent & a sponge. The powder coating came off. Called the company. They replaced burner caps. Last week there was a spill and it stained the burner bases which are powder coated in a silver color. We tried 409 cleaner, Windex, dish detergent with a sponge. Could NOT get the stain out started removing powder coating. Called the company they ONLY guarantee cosmetic appearance 30 days. They wanted $139.00 for a new set of burner bases. I am going to go back to Lowes & see if we can return this Whirlpool range.

I have the Cabrio model WTW6400SW2. I have had it for 5 1/2 years and have been happy with it up until several months ago. The F1 would come up when the machine would lock and just start to fill. I could pause it and start it again, and it might do this 1 to 3 times. It would also do it on the rinse cycle. I have been using it because I did not want a repair bill right now. The machine was also starting to make noise when it was spinning. Well, I just happened to break my dryer yesterday so I thought I would get the washer fixed also. Well, the repairman said that the controller would cost $200 for the part, and then he said the pump roller and bearings were going. By the time you add on labor, he said, “You might want to buy a new one.” He told me that Whirlpool has completely changed the washer now because of all the problems with them. He told me to look it up on the computer, and maybe there would be a class action suit. After reading some of the reviews, I will not buy another Whirlpool again.

The front of our Whirlpool washing machine started to rust in one place at the bottom within six years. Now it has broken out in three of four places on the front. We are very dissatisfied with machine and will never buy one again.

I bought a Whirlpool French door, freezer drawer on bottom at Lowes 2 years ago for $2,600. The refrigerator needed a new motherboard within the first year and now that it is in the 2nd year, service is required again. The repairman ordered the part and came the 2nd time to replace the part upon receipt. Now it needs the 3rd part since it is still not working. I have a herniated disc in my neck and had to remove everything from the refrigerator and freezer to take downstairs to salvage our food. Now I have to go through the same thing again for the 3rd time after the additional part comes. This refrigerator is junk. I asked Lowes for a new replacement but of course was denied. Does anyone know a good lawyer for this type of situation? I never had a problem with an appliance like this.

No response from Whirlpool, but I did find out what the rust was. Instead of using stainless steel or plastic or rubber, the inside light frame is made of a cheap metal that has rusted and is literally falling apart, sharp and very rusty pieces were falling into the washer tub. No wonder I find holes in the clothes that werent there before washing. I removed what I could, including the part it should hold, a plastic plate that covers the light, protecting it from moisture. My husband covered it with electrical tape to prevent injury and possible electrocution. I contacted Whirlpool, but they have ignored my questions and have not answered. They do not have a replacement part for it (stated on their parts website) They give you no solutions to a problematic appliance that should have been recalled and taken off the market due to safety issues that have caused injury and possibly worse.

We bought a Whirlpool model WFW5620HW front-load washer at Lowes. The unit shook so violently during part of the spin cycle that the Whirlpool-authorized service company technician said not to use it while parts were ordered. It seems the balance ring was not functioning. Parts ordered were shocks and tub assembly. The technician suggested trying to get a whole new unit, as the repair is so intensive he had only done one or two in his career.Whirlpool customer service said they would not replace the unit, and an escalated request had the same response. I think this is terrible customer service - when there is such intensive failure in the unit, they should provide a brand new machine. The work has not yet been done - we are without use of a washer for an unknown period of time, since the order of a tub assembly is so uncommon that they do not have a time estimate. Needless to say, we will never buy Whirlpool again, and suggest you do the same.

We were looking for stainless steel and this model was that. This model has lots of presets which we like. We lucked out and got it on sale and were able to get features of a more expensive model for a lesser price. The only downside is getting the turntable back in when you clean it. One of the things I wish it had was a way use the timer for foods cooking in the microwave plus use the timer separately for timing food you arent cooking in the microwave, but will be part of the meal. Also, the defrost options could be clearer!

Whirlpool Refrigerator Model WRX9885IBM01 French Doors - We purchased this $2,000+ dollar refrigerator in December of 2014 and within two weeks of plugging it in, we noticed the freezer drawer was crooked and ice crystals in the freezer compartment. We contacted Whirlpool re the matter and they dispatched a local serviceman. He informed us that the inner lining of the refrigerator was crooked and he contacted Whirlpool. He sent pictures of the crooked drawers and was advised by Whirlpool to adjust the outside door, but nothing could be done for the inside crookedness and that he was to take silicone and seal the refrigerator to prevent air coming in to create the ice... Really? We told him that was merely a Band-Aid to the problems and we wanted a replacement. According to Whirlpool, they can only service our month old refrigerator and cannot replace it.Actually, they cannot even service the defective product they sell, they can only caulk the problem until it comes again. I am not going to stop until everybody in the country buying a refrigerator thinks first about the warranty Whirlpool offers. After reading defective parts, etc., I am amazed they are still in business! We are contacting Lowes to come pick it up! Let them deal with the garbage they are selling!

I contacted Whirlpool in regard to one of their water heaters we purchased from Lowes. It came with a 5-year warranty. At the end of 3 years, the lower element went out. Our plumber took the part back to Lowes, where he stated they normally just do a part replacement with them. On ours, he was told the owner would have to contact the manufacturer. I contacted them and supplied them with the plumbers bill and copies of the front and back of our canceled check, along with all my contact info. Their website states theyll get back with you within two days. I contacted them on March 13, 2013. Today is April 7, 2013 and they havent emailed, called or snail mailed me. After reading these consumer reports, the air has been let out of my balloon. No more Whirlpool products for me! Integrity in our country used to be extremely high. Today it is extremely low as demonstrated by the complaints on this website and now mine. Hey Whirlpool, you suck!

I recently purchased a Whirlpool refrigerator, model number WRT351SFYB00. Several months later, I noticed a small amount of water on my kitchen floor. I moved the refrigerator and found the hard wood floor under it had been completely ruined, so the leak had obviously been going on for a long time. Possibly since day one. I called a repair man. He identified the leak was coming from a cracked drip tray which was not uncommon. However, much to his surprise, due to the design of this model, he was unable to remove and replace the tray. He explained there was a metal panel bolted in place that was preventing him from replacing it. He said this panel was also bolted to the compressor. Therefore, the best he could do was caulk whatever cracks he found in the existing tray and hope for the best. It goes without saying he could not guarantee his work like he normally does.I noticed this same complaint on a user forum website on Appliancepartspros.com, so this refrigerator obviously has a significant design flaw. My repairman said if it was his refrigerator, hed get rid of it, and also indicated that after seeing this, hed never again recommend Whirlpool to anyone. All I know is that Whirlpool is permanently off of my list now as well.

We bought our washer about 3 years ago brand new from Lowes. Like others, I have had problems with holes in clothing and spots that looked like grease. It worked well up until recently when we noticed some brown splatters on the floor. Shortly after it made a loud noise like a plane taking off and the load would become unbalanced. We researched and found many people were having issues with the bearings going bad. My husband was going to order parts to fix it but you have to have a special tool that is expensive to buy... It was going to be almost $200 to repair ourselves! He called a washing machine repair man and he said he doesnt even touch them because the repair wont last. I guess were going to be better off buying a new washer. There really needs to be a recall on this product!!!

We bought the microwave in August 2018 and last week it burned a hole through the turn table which broke it and burned a hole in the floor of the microwave. Whirlpool said it was under warranty but refused to bring a new one. They ordered a new glass turntable and painted the spot that had the hole burned in it. What makes me believe it is safe now to use? What caused a microwave to go awry in the first place. It has to be a safety issue and Whirlpool will do nothing about it. Lousy customer experience.

My Whirlpool Cabro washer does not get clothes clean. When I contacted the manufacturer, I was told that it is water saving. What kind of water-saving is it if it does not clean my clothes. I would think cleaning clothes require water. If this feature renders the product ineffective, this product should not be in the market.

The machine meets our needs and just the right capacity. It has just the right number of selection for proper washing. Very easy to load clothes and remove from the washer. There were a number of colors to select.

We bought a Whirlpool front door open washer machine from Best Buy on Oct. 2, 2011. We didnt start to use until our basement got finished. In November when the basement was ready, we found out that the machine didnt work at all. We called A&E factory service as suggested by Best Buy. They sent technicians 3 times in 2 months to check the machine. Now, it is 3 months later since we purchased the machine, the machine is still not working. We contacted Whirlpool, and they would not exchange to another machine, instead, they told us they will send another technician to check it once again. This machine costs us $800 before tax, but until now, it is still not working. Can you tell us what to do? We called Best Buy and they said this machine is under factorys warranty. So we called A& E service, who said that if Whirlpool called them, they will tell them it cannot be fixed. However, they need Whirlpool to call them because they work for Whirlpool. Is 3 month waiting not enough for a brand new machine to get fixed? And the worst thing is we still owe money to Best Buy creditor. Please help us to get rid of this! Thanks!

I bought my Whirlpool Convection oven in mid August 2019 from Lowes. I have had to call no less than 5 times about my NEW oven which I am extremely remorseful of buying. I am so unhappy with my experience mostly due to my expectation that my new oven would have been able to meet my demanding needs baking and cooking. I would have thought that it would have lasted longer than 4-5 months. The bottom left hinge is faulty which I am told is an undocumented problem for this particular oven. I noticed that it was having a problem when the oven wasn’t quite making a seal. Slowly it got worse until now it makes an initial click then I can open it about 5 to 6 inches and then have to lift it up so that I can open it without making a horrible noise and a dent in the frame.The first time I called was on Saturday Jan 4th. It took me 1 hour to get through to speak to a person. I asked why I couldn’t get a new door to the oven and they told me the hinges have to be installed separately because this model is made to be able to take the door off for cleaning purposes. They set me up for service on Wed Jan 8th between 12 and 4p. I wasn’t as unhappy at this point. I even got a text saying that the appliance company would be coming between 12 and 2. At 12 when I woke up after working nights, I got a message saying that they hadn’t received the part yet and that there would be no point in them coming. I called Whirlpool again and they told me that the part was on backorder and that in fact the part had to be fabricated and it may take up to 10 business days but that they would have the part sent directly to my house. By this stage I am very unhappy.I called back this morning and told the person that I would rather have a new oven or my money back and that my less expensive and less decorative oven that came with my house lasted me 20 yrs. I get a lot of “I’m sorry” and “I apologize” but that doesn’t fix my problem. I also told them that now the frame of the oven is being dented so I am going to have a less than perfect appliance which is no fault of my own. The only info the person could give me is the tracking number of the part they were able to locate which would be coming Fedex.I tracked it and it was due to come no later than Tuesday night. So I called the original service company in my area who told me to call to set up the service time when the part came in. I figured I would get a jump on it and call. They told me that they were all booked up this week and I would have to wait until next week. Do you think that this is how your customers should be treated? I feel as though I am being punished by choosing to buy an appliance from Whirlpool. I then tried calling back to set up an appt with a new company but the wait time was too long. I had just worked nights and needed to get some sleep. I called back this afternoon and again had to explain the whole situation AGAIN. I was able to set up an appt with a different company for Monday between 12 and 4 which happens to be on Martin Luther King day…so I am hoping it is not a mistake.Do you think this is fair treatment for a customer who just bought a brand new oven less than 5 months ago? Would you like this type of service? Would this give you any confidence to buy products from Whirlpool? I don’t believe that I would be able to recommend Whirlpool in good faith. The people who I have talked to have never been rude or disrespectful however, I feel as though my unhappiness is just par for the course. I feel as though it is just my tough luck and “oh well so sorry” instead of the attitude that you want to make everything right as quickly as possible. I ask myself if the problem was the store I chose to buy from? If I should have gone to Sears and bought one of their products or where I went wrong.

My husband and I purchased a Whirlpool over the range microwave in 2005, model number MIX155XHPT-1 and serial number TR S 30 32419. At first the top vent broke then the opening side broke off. Then the whole side of the closing door broke off. Now the whole door wants to fall off. I would have never expected this from Whirlpool, but it happened.

This has been the worst purchase I have ever made! Within 2 months of it going out of its one year warranty I called (Lowes) to have it repaired. Spent $300 on the first repair to get rid of the jet engine sound AND the oil splatter all over the floor then within one month from that repair it has a F code error and wont finish washing a load. It just stops. I have tried everything from unplugging it to restarting and it just wont work. Now have to wait 1 week for the repairman to come back out (hopefully that warranty of 90 days will be helpful). Do Not Buy this machine!!!

Will never buy another Whirlpool/GE product again. Nothing but problems. Paid $1700 for a Whirlpool/goldstar refrigerator 2 years ago. Problems from the start with slide-out shelf cracking, evaporator fan burnt out within 2 years, digital display cannot read anymore. Now have another problem again - not cooling. Going to the trash. No wonder your stock price have dropped. I would sell off to. Whirlpool/GE have been going down hill for the last 5 years. Maybe more. Cheap products, do reflect, it just a matter of time, I would think you would address these issues in your product line, but it shows your company is all about profits instead of quality of products. Keep going like you are, and you will be bankrupt. Cheap overpriced and nothing but junk in any products you manufacture.

I had one of the first Maytag Neptunes. Loved it to pieces but finally had a problem and my beloved repair guy said it was almost 20 years old so to give up and move on. Obviously, cant be without a washer for very long so grabbed this Whirlpool Cabrio Platinum Washer. One of the biggest disappointments ever! Clothes come out streaked and splotched, dont smell very fresh or clean even straight after having been washed, stains dont come out even with pre-treating, have to run everything on heavy duty, whites are getting grayer by the week, and all-around horrid performance.Im ready to give up my Starbucks, start packing my lunches for a couple months, skip whatever treats I have to in order to get back to a quality machine that can actually WASH CLOTHES. I wondered exactly what it was or wasnt doing so I stood over it for half an hour. Initially, it loads up about a gallon of water and then spits it out over the rotating drum of clothes. Then it stops and spins that water out. I suspect the design logic was that it would force that gallon of water thru the clothes taking some dirt out with it. It repeats that stupid process several times. Then it finally gets a few inches of water in the bottom and the vestigial agitator tries to move it around.I watched one hand towel lie on top like a dead weasel, never getting pulled down or pushed out or whatever it was supposed to do to get down among the other items and squish together. Life throws me everything from sick kids spewing body fluids to people coming home reeking of hydraulic and other industrial fluids. When I say clean I mean CLEAN. This piece of junk couldnt satisfactorily process half a dozen dust rags. Neptune, Im coming back with my hat in my hand and a whole new appreciation!

I bought a Cabrio three years ago. Unless you wash everything on gentle and turn items with zipper inside out, it puts holes in everything. Then exactly one week after the warranty was up, it started giving an error code. I called the company and was told this was a common error and they would send someone to look at it for $150+. It would likely be another $300-$400 for parts and labor! I had someone else (not Whirlpool) come look at it and they said it was a bad computer that I should just replace the washer, because it would cost more than it was worth. So for two years, we have had to wait exactly 11 minutes for the washer to fault then restart it and repeat 3-6 times. It takes 2.5 hours to complete one cycle. If this is such a common error, why havent they fixed it or recalled the piece of junk?! Because they can make a lot more money this way! Three people I know have Cabrios and all have the same issue and all happened within a month of the warranty expiring. I am starting to think there is some sort of timer that makes it go bad just after the warranty expires on purpose. I will never buy another Whirlpool, Maytag, KitchenAid, Jenn-Air, or Amana (all the same company with different names).

We have an 8-year-old built-in Whirlpool Estate. It is probably as basic a model as you can get. It has been 100% reliable, and cleans the dishes well, even without rinsing. We do not buy expensive premium dishwasher detergents, either. So far, we have required no repairs. Basic features--heavy wash, normal wash, pots and pans. This dishwasher is standard (not extra large.) This is not a fancy dishwasher--just white. It is what matches the rest of the appliances. We have been lucky regarding the performance of such an inexpensive dishwasher. We paid about $250 for it.

I purchased a Whirlpool Gold refrigerator in May 2012 and about 8 months ago, ice started to form in the freezer. The ice melts and water drains out, so when you come in the kitchen all of the sudden you step in a puddle of water. I called CS and they told me the best they could do was authorize part(s) and the labor and service call would be my responsibility. Everyone knows service cost way more than parts.

Purchased 11-02-2016. This Whirlpool/Kenmore dishwasher is falling apart. Top rack wheels are totally broken, ordered parts 4 times, gave up. Now they are held together by gorilla glue. I have gone through 3 gray plastic end caps for the top rack runners. Now one is contained by a plastic slip tie. Last week it started leaking. Sears was totally useless. Whirlpool keeps sending me back to them. Now, I have to go buy another new dishwasher. It will not be a Whirlpool. Next time getting the extended warranty.

We purchased a Whirlpool refrigerator because of the brand in August of 2011. Its December 2012, the entire door needs to be replaced. It appears the cost will be as much as the original $750 investment! We called Whirlpool expecting they would stand behind their brand after hardly 18 months, but no ... It is clearly a defective door to begin with.

Freezer side went out on model# ed5kvexvl00. Fridge is less than 2 yr old. Didnt expect anything to go wrong so quick. The extended warranty, I did not purchase. Replaced relay switch - no changes in problem... Contact them (Whirlpool) and like every else, got nowhere with them. 3 weeks and no fridge... Hopefully the compressor is not bad. Will find out soon. I will be researching before I select new appliances in the future. They need to be ashamed of themselves.

Whirlpool washer WTW7800 Cabrio - I bought this machine in Oct 2010 for $900.00. This October, the lid started not closing. Next thing I know, the glass is popping out. After waiting on hold for 20 minutes, I was told there is nothing they could do but refer me to a repairman at a cost of $179. The glass is popping out. This is a defect not caused by washing clothes but poor workmanship. I am on hold again. I am calling channel 3 news to do a story and will not stop until it is fixed.

I have a Whirlpool AccuBake gas range. I started by contacting my local repairman because my stove was out of warranty. The first company came out 3 times and replaced three parts, which didnt work. The cost was $297.00. I originally paid $598.00 for the stove. After they deemed it non-repairable, I contacted Whirlpool. They basically said it was my fault for not buying the warranty. I then contacted the BBB. Anne ** from Whirlpool contacted me and had another Whirlpool service tech come out at no charge to me. But guess what, they deemed it non-repairable too. Its a shame that companies no longer stand behind their product. Its very apparent that this is a manufacturers defect. They should replace the stove.

The board manufacturer number W10312659 went out. They replaced the board. The oven was 6 months old, luckily was still under warranty. We didnt purchase a extended one because mostly it had a good name and brand. Well after a year and a half the board went out again. It gives error code H5P which there is no error H5P. So the boards out. It is very costly and thats with you doing your own service. Never will I buy another Whirlpool stove.

I purchased a washer/dryer around March of this year. I have nothing but trouble out of both of them. It doesnt matter what cycle the washer is on. Its like it has a mind of its own. It may wash; it may not. Sometimes, it takes over an hour for it to finish washing. The dryer sometimes dries on one cycle; the next time, it wont. Who would think a brand new appliance would do this. Every appliance in my kitchen is Whirlpool. They dont give me any problem, and I use them everyday.

My father and I both got the Whirlpool Gold gas furnace 3 seasons ago. I can't tell you how happy we both are! Our heating bills plummeted; the unit is quiet and does a fantastic job. I am 50 and I have to admit this is in the top 5 of the best purchases I ever made. For me to take the time to find a place to write a review 3 years later should be testament to how happy I am. Make sure you have it professionally installed! Don't skimp here…this is the key!

I love my glass top stove and glad I purchased it, so much easier to clean, I think they should all be made self-clean on any stove, I did not notice that some dont come with it and some dont. Remember not to start cleaning the top of the stove until you can touch it with your hand.

Whirlpool is not what it was before. I got this set with new house... They are very poor construction. They are not even close what I have before the LG. After 6 months I begin to have problems with the dryer... Technician come two time to fix the problems. Quality of washing is OK though... That going to be the last time I got Whirlpool products. For sure.

I bought a Whirlpool refrigerator model #wrt1litzyv along with the extended warranty from Lowes. The compressor stopped working just before the warranty was to expire and had to be replaced. The cost of repairs almost equaled the price of the refrigerator and took nearly 2 months for the reimbursement check to arrive. I had to call several times. They told me they hadnt received the paperwork even though I sent it registered mail and it was signed for and I had to resend it. Now, less than 4 months later, the refrigerator is again not working properly. Freezer is not freezing properly. Takes 2 days to freeze ice. This is the absolutely worst refrigerator Ive ever had. My last refrigerator lasted 20 years. This one is only 3 years old and of course, the warranty is now expired. I will never buy another Whirlpool product. And I will never buy a major appliance from Lowes either since they play games with the warranties. And after the refrigerator was repaired, Whirlpool tried to sell me another extended warranty. They wanted $308.60 for a 3-year warranty. Ridiculous that they dont stand behind their products. And try to sell more warranties instead of just manufacturing a good product.

First whirlpool 3 door with ice maker in door failed in less than a year. Took 6 months to resolve issue, several service calls, at least 30 calls to Lowes and Whirlpool with little or no response. Nobody wanted to take responsibility to do something about my broken fridge. Even the authorized repair guy didnt want to touch it, didnt want to ruin his reputation because they wont stay fixed. Another service guy wanted to take it to the shop to repair, of course I would be responsible for pickup and delivery charge. Found out the repair was an in home repair, so didnt use that guy, I felt like he was trying to rip me off.I finally got to the right people in whirlpool organization and they replaced the fridge, that took another two weeks. I found everything takes two weeks. The replacement was supposed to be same model with upgrade, this is gold series fridge Ive been talking about. New fridge has failed also, seems like same symptoms. It lasted 1 yr and 4 or 5 months. I guess not too bad for a top of the line refrigerator, made by Whirlpool. Gonna give them a chance to make it right or I am considering hauling it around in my truck with a sign on it. Not trying to punish the distributor, just Whirlpool. This product is so bad the government should step in and force Whirlpool to give money back.

We purchased a new home in July of 2011 and we paid extra for the upgraded appliance package, which included a Whirlpool Microwave/Convection Hood Combination unit. We have Model # GH7208XRS3. We use the microwave a few times a week and only used the home 6 months each year during 2012, 2013 and 2014, for a total of approximately 18 months. From the very beginning, we had trouble with the microwave control panel turning itself on and the electronics going through various timing and programming functions independent of any human operator.During the combined two-year warranty period from July 2011 July 2013 (the Manufacturers Warranty lasted one year and the Developers extended Warranty lasted an additional year) we had 5 service calls on the same issue. The Authorized Repair Center repairman called the Whirlpool Tech Line while he was in our home and was told that there was a flaw in the design of this model. They replaced the door and then when it acted up again, they replaced the control panel. In Nov. 2012, after the repairman told us the door needed to be replaced again, we asked for a new appliance since we had the same issue repeatedly and they had already tried to fix it by replacing the door and it was still under warranty. We were told that Whirlpool would not replace the appliance until they had tried to fix it three times and we needed to get a new door again. We were told that because it was the same issue repeatedly, we would get a replacement if it still went bad after the warranty was up. So we had the door replaced again, which did not fix the problem.In late 2014, we again had the same issue with the control panel and made a call to Whirlpools Customer Experience Center. At that time, we were told that the warranty was no longer in effect and Whirlpool would do nothing to fix the issue. Even though it was the same issue that they had attempted and failed to fix while under warranty, the company would no longer stand behind the promise of customer satisfaction and told us they will not replace a 3-year-old microwave. When I asked the Customer Service Rep to speak to a Manager to escalate the issue, I was transferred to the Tennessee Office. When I got the same repeated run-around from the Supervisor, Melissa, I asked that Customer Service Supervisor to let me speak to a Manager and she told me she could not give me the name of anyone else to speak with and hung up on me.I am writing to you to express my extreme disappointment in Whirlpool and the products reliability, the way the company has handled fixing the problem and especially in the conduct of the Customer Service department. Whirlpool gave us nothing but a run-around for the years the warranty was in effect, knowing that this model has a design flaw and trying to do band-aid fixes until the warranty ran out. We were told that our only option now is to pay to have the same problem fixed a fourth time or purchase a new microwave.Whirlpool has trained their Customer Service people to be polite but ineffective and obstructionist on the phone and then hang up on the customer when they cannot resolve the customers issue. I believe that Whirlpool should be committed to customer satisfaction and making sure that their products work as intended and fix the problem that was reported while under warranty, even if it no longer in warranty. Whirlpool should be as disappointed as I am that after three attempts the problem is still not fixed and should be committed to customer satisfaction enough to replace the appliance after three failed attempts.

I purchased it new in July 2008 for $550, a single homeowner average 4-5 loads a week. First time it broke down, it was just inside the one-year limited warranty. It broke down again Sept. 2011, the basket separated from spinning mechanism. I learned that after $75+ missing day of work, repair tech quoted cost of repair $885 and a minimum of 10 days waiting for part to arrive.I called Whirlpool, the guy on the phone was nice but told me I was out of luck. Even if I had purchased the 3-year warranty, I would still be out of luck. The washer was manufactured in April 2008. What a piece of junk. Save your money and skip it. I wish I had. Aside: Whirlpool, whatever happened to standing behind your products? I used to think you were a quality brand. Im extremely disappointed and wont be purchasing any of your products in the future.

Whirlpool Dishwasher Quiet Partner III Model #8575637, White - Purchased in 2006. As of July 2013, I can say this is the worst dishwasher we have ever owned. After normal use (once a day or less), the plastic on the front control panel began cracking in the first year, and the button covers have fallen off completely. Dishes were never completely clean (at least not as clean as other dishwashers). Dishwasher leaked out one side and needed repairs. Now it is in need of a new valve, because no water is coming into the inner cavity. Repairman says it is likely that the control board, which is getting moisture into it after losing buttons, etc., will probably need to be replaced soon as well. $300 more to spend on a repair bill. SAD (AND DANGEROUS!) THAT SO MANY APPLIANCES ARE ADDING UP IN OUR LANDFILLS. There should be a LAW requiring appliances to last a certain number of years, and to clearly state their expected life on the appliance when you purchase it. Planned Obsolescence is a common business plan these days, but there must be some control on what is allowed! (I may go ahead and repair this model just because I feel bad adding one more piece of junk to our collective global pile! Sheesh!!) And all those energy star, were so green advertisements? Well, if its soon to be sitting in a landfill, its NOT so green! I am willing to pay more to purchase appliances that will last a number of years, not need many repairs, and function as they advertise... Thank goodness I kept our very first Whirlpool refrigerator - never needing any repairs and still running like a tank out in the garage. (So I know Whirlpool, at least at one time, was able to build a quality product!)

I purchased a gas hot water heater from Whirlpool. I have had problems with it since it was new. Whirlpool kept sending repair parts, which I installed, until the warranty expired. Now they say “Sorry Charlie, the warranty has expired.” The water heater has never been fixed. They just dragged it along until the warranty expired. Whirlpool has no complaint department or the repair place will not give it to you. They told me there would be no use for a complaint department. They would just tell the same thing the repair was telling me.

I am so unhappy with your product. Constantly have to restart machine. Never had a problem with my other washer. Takes forever to do laundry. Hate it.

We purchased a stackable electric washer/dryer unit and received in October. Had issues from the start. Called Whirlpool in Dec 2018 and they sent out their contracted service company. Told us they were ordering parts. Never heard from anyone. Called service contractor and they said never received parts. Called January. WP told us that because it was a new model, they didnt have the parts. We asked them to replace the unit. WP called us and said they would replace the unit and it would arrive in late January. NO CALL. Called 2/22 and said, no similar units available. Ask them to upgrade me if there were units available. Said they would and the inventory of the upgraded unit was promising. Would get a call from delivery company for a 3/6 delivery and install. 3/2: Called because hadnt heard from anyone and called WP. Today Katrina ID # ** tells me they are making the new upgraded unit with an anticipated delivery of MID MARCH. I just about flipped my lid. I asked for a supervisor of which she said she was a SR support specialist. I asked that this be escalated and I get a call regarding status. She advised that she would inquire and call me back. Likely shouldnt hold my breath or try to call back because you are on hold for up to 1-2 hours. Just to clarify, have never had an issue with Whirlpool. Every appliance we have in our home is Whirlpool. I just cant believe this experience. I am going to the media on my next stop.

I purchased a Whirlpool washer, dryer and dishwasher in 2004. The dryer and washer paint is peeling off the appliance and is rusting underneath. The dishwasher has never dried the dishes appropriately, it takes a few days to completely dry the dishes. I have lodged this complaint with customer service, also. I have always purchased Whirlpool, but I will never again nor will anyone in my family. I feel that Whirlpool should at least look into the problems and not just verbally apologize. Janice **

Just bought the Whirlpool 3.5 cu ft, Top Load HE washer (model WTW4815EW), but of course, the sales person did not explain that HE meant LOW WATER USAGE. Wish I had done my homework. FIRST LOAD, clothes seem to be beaten to death, and must pour in detergent before you load clothes. So, Oxyclean detergent I always used in my regular (NOT HE) washer put a hole in one towel and discolored (faded out) the others. Also seems that the fast and hard agitator would not (logically) last very long. It seems to be working very hard. Im SO disappointed. Called Whirlpool to say I dont like it. They said to call Home Depot and see what they will do about an exchange. When I did, my sales person said that almost all the washers he sells are HE. I want the old type washer back that allows me to add more water if I want, change the cycle and water levels at my discretion, add detergent when I want to, and soak clothes if I wish.

Within six months, the plastic surrounding the oven and the plastic handle began began to crack. Company was of no help. Also, the screen says to change filter, even after you put in a new filter. Extremely disappointed.

I have a brand new Whirlpool washer (Model WFW9640XW). It has been broken for 3 of the five weeks I have owned it. The Whirlpool cusotmer care cannot get me a working part in order to fix the machine. I am being told that I just have to wait until they find the part, with no end in sight. I am held hostage now that they have my money. I am told there is nobody I can talk to to break this impasse.

The unit has performed as I had hoped. I wanted a quiet appliance that performed well, and could accommodate large plates and platters. I never put my knives, wooden utensils, pots or pans in my dishwasher so that was never an issue. I use 1 of 5 cycles available, 1 of 4 options available. Why use something other than hot water? The delay option is used often since I have a tendency to forget to turn it on, but I never let it run if someone is not home. The time left clock is also helpful, but dont count on it being really accurate. The start/resume, delay and cancel options are often used. I used the rinse option once with disappointing results. The silverware caddy is a little small, or my silverware is too large. I do not put any pots, pans or knives in, everything else fits fine because its a tall unit. So tall in fact, that the door comes out much farther than earlier units. Im still getting used to that. The front is brushed stainless with a black plastic control panel, nothing special here. My favorite options are delay and time left. Never have used the heat to dry option. We have low humidity and Ive never had the need to dry them immediately.

I purchased dishwasher model #GU2800XTVT0 in May of 2009. Today, it leaked water all over and damaged my floor. My husband pulled the dishwasher out of the cabinet and found that the motor had fallen off. It did not have a bracket to hold it in place and worked loose, which then disconnected a hose. I called the customer service but they wont do anything because it is beyond the 12 month warranty. It only lasted slightly more than two years. This is obviously a manufacturing defect and we were just unlucky enough that it failed after the warranty had expired. The most ironic thing is that my husband worked for Whirlpool for 20 years. There is no loyalty here.

I purchased this refrigerator and have had problems with it from almost the beginning. First, the doors wholl not stay open long enough to remove items. The technician Whirlpool sent out said the cause was an uneven floor. I checked with a level and the floor is almost completely even. So, then it said thats the way it was intended to work. Isnt that what the adjustment wheels on the bottom are supposed to correct? They dont. One individual in Whirlpools customer service department told me that the doors were not a functional part of the fridge and, therefore were not covered by the warranty. What?Next the refrigerator leaked and ruined the ceiling in the floor below. A few weeks after that was fixed (the fridge, not the ceiling), the unit completely shut down and I lost a tremendous amount of food. Bad enough to have to go through this but then to have Whirlpool treat me so the horribly was absurd. Fridge broke on Friday and a service person came out on Wednesday. Tech tells me he has to order the part (control box) and I find out the next day that the part was on back order. I had already been without a fridge for a week when Whirlpool tells me the part was not available until 9/19 (this was on 8/6)! That was not an acceptable solution so I requested a refund or a new fridge. Nope, their job is to repair, not replace. They said they needed 7-10 days to see if they could get the part earlier. What? Then if it couldnt be repaired in a reasonable amount of time they would consider replacing the appliance. They would not define reasonable amount of time.I believe I spoke to about 10 or 12 different whirlpool reps, and was told 4 times that a supervisor would return my call. One person did call back when I was unable to answer the phone and I called her back within 20 minutes. Guess what, she wasnt available and she never responded to my 3 return calls. When I complained that I had spoken to so many different people and was tired of telling the fridge saga to yet another person who would not help me, she volunteered to be my point person. She gave me her direct extension and said she would handle my case. I left 3 or 4 messages for her and she never returned my call. In other words, I was constantly told that I would receive return calls but never did. In summary, no one cared that I had an almost brand new Whirlpool refrigerator that was not working and that the date I could expect a repair was indefinite. In addition to all of that, every time I called they were experiencing a high call volume. Maybe they could hire more staff? When this all started, Home Depot told me I had to go through Whirlpool because it was under their warranty for the first year. Finally I decided to go to the store (after all, I did pay them for the fridge). After 3.5 hours in Home Depot, they agreed to replace the refrigerator. I havent gotten it yet (they did send over a small loaner), I am really hoping this is the end of this fiasco. I want my life back!! !

I purchased the four-door Whirlpool stainless steel refrigerator. It was installed on the 15th of June. One month later, the ice was not coming through the dispenser and if it did, it was a small amount. During this time, I was receiving notices from them about purchasing an extended warranty. Today, August 23, 2012, the ice maker stopped working completely. I was disgusted. Paying for the top-of-the-line refrigerator that doesnt last for 90 days is ridiculous. Also, the handle on the vegetable keeps coming off. That will be the last Whirlpool appliance I will buy.

My issue is I believe that Whirlpool should pay for my tub and bearing part because the washing is only 16 months old. Because it went over the one-year warranty by four months, I shouldnt have to buy this part considering it is such a big break for such a young washer. Please advise if Whirlpool will assist me with this issue.

Ive got a brand new house, with brand new appliances by Whirlpool. Within less than 6 months, my dishwasher, Model no. DU1015XTXB0 Serial no. F00702058, had its electronic board gone bad. Instead of replacing the dishwasher, Whirlpool replaced the part. Not even one year later the same part went bad. Now, the dishwasher is not even 18 months old and it will cost $255.00 to repair. It is just the two of us in our home and I bought Cascade packets 20ct x 5 at Sams. Im not even done with the packets, so I know 100% that we have run the dishwasher just 70 cycles in 18 months.

We bought our Terrorpool Whirlpool refrigerator in 2006. We have had problems with the ice dispenser, bad motor replacement, and now we have cracks all down the right inside wall. I had bought an extended warranty of four years at the time of purchase which covered the cost of the previous problems. But it has now expired, and I was told it would be my expense for repair. What happened to reliable appliances that our parents and grandparents had? What happened to the name Whirlpool? I will never buy a Whirlpool product again, not to mention the customer service (which I wont mention). If you have model # ED5PHEXRQ00, please write about any problems you have had and help someone else not make the same mistake.

Whirlpool refrigerators are best whenever I used many refrigerators. It provide many useful service to users. It allow us to store different varieties of products including vegetables, fruits, beverages and many more. It can make cube ice for to use in different drinks, products, etc. It consume less energy to used this Whirlpool refrigerator products. We used Whirlpool refrigerator with less stress of storages of fresh vegetables and fruits. Water is main thing we used to store in this fridge, it maintain temperature well for cool and fresh taste of nectar of nature. Nowadays, refrigerator are used widely in our locality especially Whirlpool which I mentioned them earlier to buy this awesome product to give comfort of mankind. I recommend Whirlpool refrigerator.

I purchased the Whirlpool Cabrio Top Load Washer in 2009. It stopped working and I found that it needs a new control panel and recirculating pump which will cost $390, including labor (plus the cost of the service call to diagnose the problem). I would not have expected to have this type of problem with a washer within 3 years of purchase. I cannot recommend this machine.

I bought a gas range (#WFG524SLAB0) in July 2012. Two weeks ago, the oven stopped igniting. I called Whirlpool to have it serviced and they sent out someone from A &E Service Repair, who told me an igniter had to be ordered and it would take a week to come in. (He said he will order the part.) Then he told me to call Whirlpool again and schedule another appointment. Whirlpool sent out one of their techs two days later, who told me the same thing about the oven and said a part will need to be ordered. I told him it was ordered and he looked and said no part was ordered. So this was the week of Thanksgiving. Because the part would not be in until next week, no one could fix the stove until eight days later. So my Thanksgiving was ruined, no less with not being able to cook. So the service tech came to put the part on and the oven still is not working. He pretty much told me there was nothing he could do, for me to call Whirlpool again and have someone else look at it. I called Whirlpool and actually spoke to a supervisor who basically told me the same thing I have been hearing for two weeks: “We will send a service tech to look at the problem.” Keep in mind the stove is only four frigging months old. So here I am waiting again for someone from Whirlpool to fix my oven.

I had purchased a washing machine trough CSD canteen and go for AMC for five years on September 25, 2006. In September 2010, I lodged a complaint and the Engineer visited and asked for a replacement of the bottom cover. I said okay, but later on he told me that I have to replace the complete outer cover. I agreed and asked them to replace it. The cost is fixed for 2,500Rs. They replaced the cover but did not replace the bottom cover.I talked to the agency and they agreed to hold to 1,000Rs for the bottom cover and I paid to them 1,500Rs. Later they brought an old cover and I refused to replace that. They told that the bottom cover is not available. Then they never tried to replace the bottom cover. I arranged for the same from the local marketing for 600Rs and replaced it. I paid the service charge for the engineer.Later, I lodged a complaint that the machine was not drying the cloth. The engineer visited and told me that the belt will be replaced on payment. I agreed and he told me that I will visit the next day and replaced the belt. But he did not come until it was late.On September 18, 2011, with number DL0911018283, my machine was not switching on and I lodged a complaint to customer care. But no engineer visited me. Then I regularly complained but there was no response from the agency. On September 23, I talked to customer care, Mr. **, that I am going out of station and I lodged a complaint from the last five days that no engineer visited me. My AMC is expiring on September 25, 2011. I will come back on October and then send the engineer. On October 9, I reminded them that they refresh my complaint with number DL1011007031. The engineer visited and told me that the PCB of the machine is faulty and I have to pay 3,500Rs.I told him that I complained for this problem during the AMC period, hence they are supposed to repair my machine free of cost but he refused. I talked to customer care and tried to resolve the issue but I was not successful. Then I talked to Mr. **, the head of Customer care in Delhi, on October 12. He promised to resolve the issue but no engineer visited me and my machine is still defective. On October 13, I tried to contact Mr. ** several times but he or his PA is not picking up the phone. Now, how will I get to repair my machine?

My Whirlpool Cabrio Washer is a bucket of junk. I bought the washer in about 2008. I was smart and bought the warranty for approximately 3 years. Since I bought it, I have had them replace 3 water pumps, the tub, the computer, and it still knocks and shakes. It also leaves small frayed holes in my beach towels. This machine should be recalled. It needed a warranty from day one. Washer cost $1,000 warranty every year $130.00 per year which covered the repairs at about $900.00 for repairs. I hate it. I just hate it. I can’t stand it anymore. I need a new washer, someone has got to listen.

Since May 3, 2016, five servicemen have failed to repair my Whirlpool refrigerator (WRF560SEYM), which is less than 2 yrs old. One trainee from A&E Factory Service had the nerve to reinstall broken parts. I have been completely without refrigeration for the past 48 hrs only to learn that the repairman scheduled for tomorrow has been cancelled because AIG warranty has not approved his visit. Further investigation reveals that the parts were never ordered, pending approval from AIG. Whirlpool cant help me because AIG has not declared the appliance unfixable. Hhgregg cannot help. I have spent countless hours on the phone on hold & wasted hundreds of dollars on spoiled food. Dont trust Whirlpool. Theyre not the company they once were. Their warranties arent worth the paper theyre printed on. Buyer beware!

This washing machine has not worked well from the time I bought it two years ago. It never fills to the amount of water required to clean clothes, it is always off balance, so I need to adjust the clothes at least five times per load. I end up wringing my load out by hand. The clothes come out smelly and not clean. After the cycle is done all the clothes smell like mildew. The other night while doing a load, it made such a loud noise in the motor and started to shake up and down, and then moved forward, like it was going to take off or explode. I tried to do another load, but after it filled and started to agitate, it started to make a loud grinding sound and there were 25 minutes left, then the timer showed 26 minutes left, like the computer in the machine is messed up. I had to empty the water out, wring out a load of clothes including towels, exhausting.The worst part is that the machine is finally paid off, I am a single mother on a disability and I am stuck with this piece of junk. I felt desperate so I looked up Cabrio washing machines to try to figure out what could be wrong, and then I find all these negative reviews, and these owners all have the same issues. Why has there not been a recall, or a class act, who can afford to replace a $700.00 washing machine every three years. I also purchased the Cabrio dryer which cost over $700.00. I do not trust that it will be any better in the long run.I cannot rate this machine as it has been a nightmare from the start. White socks seemed to come out with more dirt than when I put them in, and I am sick of using bleach all the time, the fumes make me feel ill. This is not acceptable, obviously this item is defective, and a prominent company such as Whirlpool should take the loss, not all the victims that paid too much in the first place trusting that Whirlpool was a reputable company, I will never give them my trust or business again. I hope to hear from you, and if there has been a recall or class act legal actions, please let me know as I want to be involved.

We bought a Whirlpool Range gas stainless steel five burners on top. We haven’t had it a year and the paint is chipping off of it. It’s starting to rust now. I know stainless steel ovens. You have to clean them specifically with certain chemicals which I do so there should be no reason why it’s rusting and the paint coming off of it. Hasn’t even been a year yet since we bought it.

Whirlpool over stove microwave/convection oven model GH7208XRY-4 - I purchased this top of the line unit in April 2012 for a vacation home kitchen remodel. It wasnt installed until June 2012 and stopped working in May, 2013 just after the warranty period expired. The problem was with the touch screen panel that went blank and the fan/light control switches also failed. This unit has only had light use since my wife and I are retired and use it primarily for heating tea/coffee. I contacted Whirlpool customer service and they graciously offered to cover the cost of replacement parts but I had to pay a service charge of $125. The factory technician said the whole door needed to be replaced since the electronics were not readily accessible so it took about a week to get the replacement door which turned out to be the wrong one and needed to be reordered. The technician finally replaced the door and the faulty fan/light switch. Within a month the fan/light switch failed again but was still under warranty so it was replaced for free. A little more than a year after the last service the touch screen control panel began operating by itself changing screens and beeping randomly. This was somewhat disconcerting but the unit continued to work pretty normally until my wife placed a small plate of leftovers in oven to be reheated for 1 minute. She walked away to do other things and forgot about the food in the oven until we noticed a strong burning odor and found that the microwave was still running some 20 minutes later and had turned the food into a black mass of burned food and the plastic cover was melted and burned.I contacted Whirlpool service thinking that the unit was under warranty from the previous service but they said the parts only carried a 90 day warranty and my only recourse was to pay for another service call and purchase another door panel for approximately $400 or I could buy an extended service contract for $300. Needless to say Im not about to spend that kind of money to, at best, get another year of service from this inferior product. This is simply not a safe product that could have started a deadly fire if I had not been present to stop it when I did. I have probably owned a dozen microwaves from other manufacturers and have never had any kind of problem including a comparable GE unit that has been flawless for over 15 years. I am extremely disappointed that Whirlpool has cheapened its product line to such an extent but I suppose I shouldnt be surprised since I noted this product was made in China.

I redid my kitchen two years ago. Put in Whirlpool appliances because they matched my refrigerator. I have been very happy with all aspects. It looks good, it’s easy to clean and cooks well. It doesn’t have a lot of special settings. Less to go wrong.

I’ve had this washer since October 2018. Worst purchase ever. It does not clean the clothes nor does it put enough water in it. I’ve tried the deep water option too and it’s for sure still not enough. I don’t understand how they even thought that this was perfectly fine to sell. If I could’ve taken it back a month after having it, I for sure would. And no one will buy it because they’ve read reviews of how it’s terrible. I wasted $900 on this washer. I have the dryer also which works amazing. The washer just sucks something terrible. My husbands military uniforms always look dirty and a lot of the clothes aren’t ever wet. I’ve finally seen a picture of how you’re supposed to have clothes in there. Why in the world would you only allow barely a layer of clothes at the very bottom to be cleaned by the agitator? Why would you have this huge drum only to put not even a load in there? This was such a waste Whirlpool and I’m glad I’m not the only person who has the same issue. I will never purchase another Whirlpool washer, it’s upsetting I can’t currently get rid of this crap washer I have now.

The 12 year warranty, means nothing. The heater only worked for 30 months, and then its upper sensor fault code flashes, and the heater shut down. I called Whirlpool, and they have me use an ohm meter to help troubleshoot the problem. So if you are not handy, you are out of luck. They decided it was my control unit that is defective. They will send me the part free, but I have to pay shipping and installation. What a deal, and what kind of management would dream up of this. The heater is marketed as a 12 year warranty model (only on the tank). Would anyone, having been through this, buy another Whirlpool product?

When renovating my kitchen I went with all Whirlpool appliance. I have nothing but trouble with my fridge. About a year old we had to replace the motherboard at our expense. After having that done, about 6 months later I had to defrost it so it would work again. Now it has to be done every month. All they say we can book another service call at my expense again. All I say thank goodness I kept my old Frigidaire. It saved me more than once. So my advice is stay away from Whirlpool. They dont stand behind their products from my experience.

Whirlpool 50 gallon water heater - I bought a high efficiency tank water heater less than 1 year ago from Lowe’s. It stopped working after 10 months. Lowe’s indicated that it was a manufacturer issue so I called Whirlpool. After talking to the service rep, they said they would send a part, which I would need to install or call a plumber. The part didnt show, so I called again. This time I was told that they needed to confirm the problem with a local service tech. We are now at 5 days without hot water, and it looks like it is going to be another 3. Dont buy Whirlpool. Lowe’s has tried to help but cant get anything done either.

The heater was bought in March of this yr, 2013! Already, it quit working! Error message... we got the replacement part after much hassle! It was replaced and still doesnt work! Its going on day 11! I am furious! The unit needs to be replaced and I get, Well, you have to pay for labor, etc. You have got to be kidding me! It has been in my house for 3 months! I will call the media, our local guy who investigates, if this is not replaced asap! I already know I will never buy anything Whirlpool and will tell everyone on my media not to either!

Purchased a Whirlpool french door refrigerator at Lowes less than two years ago. Last week the freezer compartment failed, out of the one-year warranty of course. The independent tech who came to service the machine told me of all the refrigerators he services Whirlpools are the closest to total junk and he would never recommend them. Wish I knew him before I bought this soon to be piece of trash. The CEO of Whirlpool, Jeff Fettig, received total compensation valued at $14.4 million in 2010, up about 15% from a year earlier, the appliance maker reported in a securities filing recently. Appears to me that Mr. Fettig is ripping off customers for his own gain, with his boards approval. Shame on all of them -- another example corporate rip offs that are plaguing our nation.

Refrigerator Model ED5FVGXWSO2 - After owning it for a couple of years, we decided to do a super cleaning and remove all the shelves. When we took the shelves out, I noticed that the plastic support tracks were all cracked. I called and complained to Whirlpool and of course the fridge was out of warranty but heres the good part - The person on the phone asked me Did you put heavy things on the shelves? OMG My response, trying to think of the heaviest thing possible, was, Like milk cartons and juice? She even said There was likely a bad batch of plastic when the shelves were made. I was a big fan of Whirlpool. Great value etc. but I will never buy from them again. Shelves should last the life of the fridge!

We bought the Whirlpool Cabrio forcibly when our 20-year-old top load whirlpool finally gave out. The Cabrio sucks. It does not get anything clean, it ruins clothes due to low water which creates friction, clothes are left wrinkly, smelly, pilled with lint, stinky and unclean. Ive had it for a year and Ive given every cycle a chance. It simply does not do what it is supposed to.The HE washers are supposed to reduce water, but having to rewash everything several times with load times up to two hours not only increases the amount of water used but increases the amount of energy used. Our electric bill has gone up $30-55 a month on average. This doesnt even account for the fact that Im spending nearly 16 hours a week doing laundry for a household of five. Thats nearly triple the time I used to spend on laundry. From having to pretreat even the most minor stains to spending hours trying to get the wrinkles out, and having to remove pills of lint, to the fact that one wash cycle does not get the odors out nor the dirt out therefore multiple cycles are required. I honestly think I might spend less time if I hand wash everything, I certainly would get them clean and deodorized. UNFORTUNATELY Government regulations force the consumers to buy HE washers so our choices for clean deodorized clothes are non existent. If I had to do it again I would buy a used non-HE washer knowing it would run another 10 years and actually get my clothes clean.

I feel as though they could use some additional features, it’s also hard to change out some of the wiring in the back. I’ve had some issues with smells coming from the washers as well from them. Hopefully they can start to look into tweaking smaller details to improve the overall machine.

I got a new Whirlpool dishwasher and it is totally unacceptable. Its supposed to be energy efficient and the eco setting, which is supposed to be the most energy efficient, takes 3 1/2 hours and does not do a good job, doesnt dry the dishes. Ive tried all the settings and some take over 4 hours. I have talked to someone at Whirlpool twice and they say thats the way it works. How can anyone put out a product that doesnt work and get away with it? I had my last Whirlpool for over 12 years and it took not even an hour and did a wonderful job.

We bought our Whirlpool Cabrio washing machine and dryer in May and it was the worst purchase we have ever made. We have had a technician out to our home three times. Whirlpool said that the next time the technician comes out to your house, you will have to pay for it and we have the extended warranty! The problems with the washing machine are many. 1. Leaves white streaks on dark clothes. 2. Not enough water covers the clothes, so clothes do not get clean. 3. The spin cycle is so violent that clothes are damaged. 4. The soak cycle is a joke. Soaking means to sit in water and soak. This machine drains the water so there is no soaking.5. With this very expensive machine, we can use only one cycle; bulky items on the low spin with a repeat rinse.The dryer is equally terrible. As I write this, I have two pairs of jeans going through the dryer for the third time. According to the technician, a heat sensor determines whether the clothes are dry. We have not had one load of laundry, big or small, that has dried in one cycle. But the technician said that this is how this machine works. We have tried all the cycles. According to Customer Service, the technicians found nothing wrong with the machines hence, we will have to pay for the next repair call. If you are looking at this machine and dryer, dont! Do not waste your money or your time. Washing laundry is a nightmare because the machines do not do what they are supposed to do --wash and dry the clothes.

Purchased my Whirlpool WRF989SDAH00 White Ice fridge late September of 2014, received the fridge Early October, todays date is Dec 17, 2015. The freezer is not freezing food properly the last couple of days, all food is unfrozen in the freezer. Have lowered the temp settings has not helped, the fridge section is temperately fine. There is a noise coming from the fridge that sounds like a noisy fan or motor. Phoned Whirlpool Canada, they said they could send someone out. They will charge $100 for call out and over $20/15 min after. I asked whod theyd be calling to service. Said that Id try unplugging the fridge for a couple of days and seeing if that helps, and that Ill call the refrigeration company myself if I need them. Not satisfied with their short term warranties. Especially on such expensive products.

We bought the set washer/ drier from Lowes in 2008. The first problem was that it wasnt rinsing well. After finishing the washing cycle, clothes were still dripping water. It took us to make several phones calls to get the problem solved. Also, the clothes were smelling bad and needed to be wash again. Now we are having another situation that it start the wash cycle but it wont finish and shows a code F35 or sud.

Mold in my dishwasher right after having washed the dishes!! This is the first time I have seen the mold on the racks (lots of it!). However, my neighbor also has a Whirlpool and complains of the mold all the time. Also, my dishes often do not come clean. I would not have purchased a Whirlpool, but it came with the house, three years ago. Therefore, I do not have a receipt for it.

I dont think I ever bought another product where one of its highlighted feature does absolutely nothing. Using the Aqua Lift cleaning process is a waste of time and electricity. We were told this range had a self-cleaning oven when we bought it. If a self-cleaning oven is important to you buy something else.

This Whirlpool refrigerator/freezer Model W10314956B was purchased from Lowes on June 29, 2012. Recently noticed rust appearing under ice/water dispenser tray. Requested warranty service, but was told the problem was considered DUE TO WEAR & TEAR! TOTAL COP-OUT! There are NO MOVING PARTS in this area; how can there be WEAR and TEAR? To my mind, this can only be charged as SHODDY MANUFACTURING or INADEQUATE QUALITY CONTROL by the manufacturer.This appliance is only 6 1/2 years old! Consumers expect refrigerators to last much longer than that. The only possible cause for this problem is as stated above: poor quality control by the manufacturing plant, and I completely discount being told the problem was due to WEAR and TEAR! I will think long and hard before I ever even CONSIDER purchasing another Whirlpool product, and maybe YOU SHOULD TOO!One issue that keeps gnawing at me is HOW, since this is supposed to be a STAINLESS STEEL refrigerator, can it rust? The best answer I found on Google was that its likely due to insufficient chromium in the mixture of metals used to make stainless steel. To me this continues to point to shoddy workmanship at the manufacturing plant. I have pictures of the problem, but for some reason Im unable to copy them to this complaint. Probably because Whirlpool is afraid of pictures that confirm their shoddy craftsmanship!