Since 2010, our 2006 GE 1.1 cu. ft. countertop microwave oven model # JES1136WL has had power failure problems. It began in our previous home and now in our next home. All of a sudden, Id check the panel and it would say PF, which means power failure. So, Id reset the clock and there it is, ready for the next usage. Over a year later, in our new home, as of yesterday, it will start and immediately cut off. Now, weve been using this microwave in the same plug since May and now its October. So, what happened? Today, Im looking for the users manual and have located it online. But it appears that the PDF GE has for it, the Adobe document, has a problem. So, Im going to check it on my laptop, as this is my PC. Thank God we only paid under $100 for it. On some of these consumer complaint stories, the person paid a great deal for theirs.

We have had our GE Advantium for 4+ years and the paint has started to peel off the inside of the door. We have an extended warranty with Home Depot but they deem this a cosmetic issue which is not covered. The cost to replace the door (part only) is about $260. Not sure self-painting is safe. I read here that we are not alone in GE microwave paint peeling off inside their microwaves, in general. Has there been any recall or calls action against them for this shoddy product? We love having this microwave/oven but feel like we got hosed by GE and Home Depot.

This is the second time that my GE microwave oven is peeling the paint on the inside of the oven. We paid over $240.00 the first time and think that this is a serious flaw this particular oven has. I think that the company should be liable, not the consumer.

Have a GE dishwasher put into operation June 2016 (new home). In Oct 2016 we noticed a leak and a serviceman came out and identified a loose soap dispenser - tightened it. Next time we used it, leaked as before. Same serviceman came again, this time replaced both the main seal & spinning water distribution wand assembly. Again, the unit leaked and on Dec 14th same serviceman replaced the soap dispenser. Before he got too far down the road, we called as the unit again leaked. He blamed it on excessive soap suds - which he removed manually. Following his departure, we again experienced a leak. Same serviceman returned on Dec 15th. After review, he advised us the DW would be replaced and we should get a call within 48 hrs to arrange. On Dec 17th (still no followup from GE) the DW leaked again - we video this time. On Dec 19th called customer relations and after much discussion it was apparent GE has NO CLUE what the heck they are doing. ONE MORE repair trip was scheduled - this time they would replace the inside and outside panel! We are fortunate to be retired otherwise this repair process would have cost us about $2000 so far! How idiotic is GE?? How much have they spent to avoid replacing this unit? Believe me this is the LAST GE appliance we buy from them. Dont know how they stay in business. We are awaiting the panel repair guy as of this writing. Will update once this service has been completed.

I have a built-in GE microwave. It is easy to use and best of all very easy to clean. It is brand new and stainless steel. Looks nice on the wall above the built-in GE oven. I can easily reach it. Some built-in microwaves are too high.

My Microwave oven is 22 years old. It still works fine, but does not have power levels on it. The reheat is vague and I have to keep checking so things dont burn or dry up. The dishes get very hot after about only three minutes. Other than that, it is easy to clean and still looks good.

We have a GE Profile Microwave/Oven combo unit. The paint is flaking off inside the microwave. Most of the ceiling paint is gone, and the floor of the microwave is flaking. Because we have a combo microwave and oven, the entire unit must be replaced. Thats around $2400. We cannot match the color, because they dont make bisque appliances any more. GE customer service suggests we replace the microwave with a countertop model, leaving the dead microwave on the wall. This is unacceptable.

GE over the range microwave Model hvm1750DM1 WW - It’s just about 2 years old. It started making a grinding noise, then quit. No more GE for me.

Does just about everything my ovens do, but better and certainly much, much faster. Bacon is crisp, chicken tenders - tender, puddings are creamy, and on and on. Try poached egg or an oyster levant, wow.

Three years ago, we remodeled our kitchen and replaced all our appliances with GE Profile Stainless Steel appliances, stove, refrigerator, and dishwasher. Two months ago, the dishwasher, model PDWT580R10SS, stopped working. It was out of warranty, but the store where we purchased it said to call GE consumer service to see what they could do. They said that they would replace the parts for free if we paid for service. They said they would send a GE certified service tech to fix it. The two people they sent were dumb as a brick and after tearing apart the door, they decided that the controller board was bad and sent for a replacement. Two weeks later, they installed the new controller board and it still didnt work. They called GE and were walked through a troubleshooting guide and it was determined that the touchpad was bad. They ordered a touch pad and two weeks later, they arrived to install it and asked where the part was. According to them, it was sent to me and was at the post office, which it was not. They then asked to be paid for the three calls and I told them I do not pay for incompetence and would pay them when the appliance was fixed. Turns out, they gave GE the wrong address (their store) for the part and it was sent back. I called GE Consumer Service and talked to my rep who said she would send the part directly to me and that the service rep refused to work with me again and I should contact another service organization. The part came and it was not a touch pad, even though the packing list said touch pad. I called the GE rep, who is now a good friend and she said she would contact the store where we purchased the dishwasher and have them fix it as long as I paid for the parts. It is now two weeks since they arrived and diagnosed the problem. I just called the store and they said the part was backordered for another week. It will be close to three months before the dishwasher will be fixed if it can be. DO NOT, UNDER ANY CIRCUMSTANCES PURCHASE A GE APPLIANCE.

The looks are ok. It works great, not too noisy. Wouldn’t mind replacing it with a different color and apparel. It fit great over the oven and is a space saver. Cleans up well, not too hard to clean. Not sure of the exact price, but I remember it was very cost efficient

Ive had a GE model #JKP68G microwave oven for the past 27 years!!! It has been absolutely fantastic!! I love GE products and how reliable they are. Theyre the best!

Last summer GE replaced the peeling handle on my microwave oven. I have treated the new handle with kid gloves. No abrasive cleaning products have been used and the oven burner under the handle is used infrequently at very lower temperatures. One year later its peeling AGAIN. All the burner control bezels on my GE Cafe oven have also peeled. The handles look like plastic covered with aluminium foil. Cant believe GE hasnt fixed this problem or issued a recall. I will NEVER purchase another products made by GE!

We bought 3 GE Profile appliances in 2005 when we renovated our kitchen. We have not had much problem with the gas oven/range/stove. We have, however, had nothing but problems with the microwave (which I submitted a separate review for) and the dishwasher. Recently, a friend made some suggestions regarding the dishwasher. I then went online and watched some tutorials on troubleshooting my dishwasher problems. I tried all the new suggestions and the dishwasher worked OK the one or two times after that and then back to all the old problems: 1. We have to scour every dish until its nearly clean before loading (even though the instructions specifically stated no pre-rinsing necessary). 2. I am not sure the soap cup opens. The soap is always left caked in the cup resulting in running the dishwasher twice. We have tried all kinds of various soaps and they all do the same thing. The eco-friendly soaps are the worst. We strive to be eco-friendly, but how can we be if we are using the harshest soaps possible AND running our dishwasher twice?! Not to mention the pre-rinse scour and running water until it is 120 degrees prior to running.3. The dishwasher also leaks and is very noisy.I have read some other reviews on this product and realize our dishes are not always dry at the end. This is a non-issue for me. I dont care so much if the dishes are dry. I do prefer for them to be clean. Dishes are a task I do not prefer to do. It would be nice to have a functioning helper. I am grateful the thing hasnt caught on fire. I saw that this dishwasher currently sells for $800-$1,500. I cannot believe it. I wouldnt spend $100 on this piece of junk.

We purchased a new General Electric (GE) Adora microwave model DVM1850SM4SS from Home Depot for approximately $355.00 in 2010. It was manufactured in Malaysia and had been in use for 2 years and 9 months before the magnetron failed. I spoke with a GE Customer Care representative on two occasions, and she said that the best that GE could do was split the cost of parts and labor since the 1 year warranty had expired. We had not purchased the extended warranty believing at the time that a microwave generally lasts for many years, and GE had always made quality products and would stand behind them. I indicated that I wanted to have the problem properly diagnosed by the service rep recommended by GE before proceeding further. The 10-minute service call bill set us back approx. $100.00. It would cost at least another $170 to replace the magnetron if we used the service tech contracted by GE. For $270, I believe we could find a fairly nice new microwave. I looked at alternative options for repair or replacement, since I am rather partial to the looks of the over the range stainless steel Adora. The model we have is no longer manufactured, but GE now offers the 1.9 cu. ft. Adora that Home Depot sells for around $400.00. In my internet research, I noted several postings that indicated that due to the high voltage danger of the magnetron, only trained technicians should attempt repairs. After half a dozen calls, I fortunately learned of a Microwave Service Center close to our residence that could replace the magnetron. After taking it down from above the range, hauling it in for repair and paying the approx. $104.00 bill and hauling it back to our residence to mount on the wall, we have a microwave that should work for a while! Total cost including service call for diagnosis - $204.00. Considering that GE does not wish to stand behind the quality of their products, I would not be likely to purchase a GE product again.

First Profile microwave/oven caught on fire. Was replaced. Front panel on Profile refrigerator not reacting to touch. Repairman said that this model had problems. Fixed it - cost over $100.00. Dishwasher (Profile series) not worth the cost of heating the water to run it. Cleaned dishes by hand. Stove top died - not reacting to touch. $90.00 for repairman to visit us, and another $60.00 to tell us what was wrong. A lot of money for inferior products.

I replaced a GE JEM25 microwave when the Magnetron gave up with a PEM31DWW unit. Within 14 months the paint on the ceiling of the oven started flaking off. Contacted GE and they offered to sell me another oven for $166. After reading all the negative reviews on this site, I dont think I will ever buy another GE product.

GE built-in oven with microwave on top in white color, model no. JKP90CMICC. Microwaves outside door is peeling off in chunks. This is a manufacturer defect and I have contacted GE to see if they will stand behind their products quality and replace this door of the microwave. I have heard so many negative things about GE customer service so I dont have much hope but I have to pay to replace this poorly constructed door. I will never buy another GE product and I will spread the word on how they treat their customers. I will post again when and if I hear back from them.

We bought a suite of Slate GE appliances during kitchen remodel 2 years ago. Weve had the dishwasher, model GDT580SMF2ES, motor replaced twice now and it is still loud and stops intermittently. Thank goodness we have the extended warranty! The over stove microwave is now starting to run when we just shut the door and stops intermittently. Were ready to replace everything with a reliable brand and cut our losses. We will never buy GE again.

I have a GE over the range microwave oven purchased in 2011. 4 years old, hardly out of its service life. In 2013, while heating up my lunch, I heard a loud buzzing and popping noise. The plastic hooks that hold up a metal tray (yes, the unit comes with a metal tray) in the microwave oven caught fire. I called GE and demanded they repair the unit, they said they were not responsible since it was out of the warranty period. Having experience in the insurance industry, I reminded them about product liability, if this is a common occurrence, there would be potential liability issues for GE. The service tech said they would send someone out free of charge to repair the unit. He replaced the two hooks that fried and said they were no longer responsible for unit. Today, 01/28/15, we just had it happen again. One more hook caught fire. Hey GE, do you really think I will buy any kind of appliance from you again when you make a defective product and dont stand behind it? I will not. I would recommend people do your research carefully when buying a microwave oven, especially one from GE. I would recommend anyone do research when buying any kind of GE product since, in my opinion, they clearly do not care about their customers.

My GE counter top microwave (JES1456), purchased from Home Depot less than a year ago, just stopped working today. No lights, or anything. The electrical outlet is fine. The GE warranty appears to be effectively meaningless. It is cheaper to replace the oven, than have it repaired. I will avoid GE products in the future.

We purchased our Adora over-the-stove microwave oven from Home Depot. The Adora brand is made exclusively for Home Depot and were sold on its special functions and value. Well now, 3 years later, this exclusive models glass fogs up when we use it. There are only 2 of us living at home. We use it maybe 4 or 5 times a day. A microwaves typical lifetime is 9 to 10 years. Also, by the way, when we turn on the fan to highest, it sounds like an express train hurtling through our kitchen. Our dog had a heart attack and died the first day we operated it. No he didnt. We dont even have a dog. But you get the picture.

After having my Cafe Stovetop for about a year and a half, there was a electrical component malfunction. During this, smoke came out of the stovetop and it smelled of electrical burning. I sent a complaint to GE since several components were damaged. Knowing that the warranty was only for 1 year, there would be nothing they could do except sell me the parts.

I have the same microwave for 15 years and it works great, we use several time a day to heat up food. I would highly recommend this product to all of my friends and consumers. If I remember correctly my mother had a GE microwave and oven when I was growing up.

Our microwave caught fire today and burned our kitchen, stove top, & attic. According to the Fire Captain, the cause of the fire was the GE microwave panel shorting out. Had my mom not been standing right there as it happened, our entire house would have surely been a loss.

GE over the range microwave JVM1540DP1WW - Within 1 year, the magnetron failed. I called the Sears service department to fix it. Because of that, I bought 2 more years of extended warranty. Three months after that, the microwave turned on by itself for 1 minute nonstop. I had to unplug it and call the service again. It would also turn on even when the door is open. Its very dangerous for microwave exposure!

I live in a condominium building with approximately 105 units. We all had the same GE microwave installed in our units approximately five years ago (contractor-installed). I sent out a mass email to all of the owners to ask if they were having the same problems I was having my microwave, which was the touch panel will not accept commands. I received approximately 15 complaints from various homeowners with the same complaint.When I called GE to tell them the problem I was having with my microwave, they told me a technician would have to come out and diagnose the problem. The service call would be $99.95, and at that time the technician would let me know what the problem was and tell me the charge for the replacement part and labor cost. I told GE Customer Service that there were many people in my condo building who were having the same problem and I wanted to know why each homeowner should have to pay the initial $99.95 service call fee? The response was, That is our policy. To placate me, GE customer service said they would charge me the initial fee but I would receive a 25% discount for parts and labor.In the meantime, two or three other homeowners made service call appointments for their microwave oven with GE. One homeowner was given a fee for parts and labor, which would have been only slightly less than buying a new microwave and another homeowner was not given a labor cost. In both cases, the homeowners did not go forth with their repairs, because buying a new microwave was more cost effective.I want Consumer Affairs to know GE grossly mishandled this malfunction issue amongst a group of homeowners who own the same microwave. Secondly, I realize the microwave ovens are five years old, but GE should have some record regarding failing parts along with the life cycle of this product. Lastly, I want GE to be held accountable for not telling consumers a repair cost for certain issues. There should be a cost per hour, not cost per broken item.I kept records of all correspondence amongst the homeowners of my condominium building, so I will be of great assistance if you need further help from me. Product malfunction is a GE Profile Spacemaker 2.0 Model # JVM2070SK02.

GE is a proven brand and its quality for reliability. When I was shopping for one I went with a known brand. Planning to upgrade my kitchen and will be shopping for a countertop microwave. The over-the-range microwave has stood up 15 years of use. Happy with purchase and performance. Will purchase GE brands in the future.

I have an above the range GE microwave oven, model no. JVM1750M1CC. It has been in service for about 9 years. About 6 months ago it stopped working with an F3 code. The code claims the control panel needs to be replaced. I found that the price of the control panel was over $100 and the service call was at least $100. A little shopping around and I found I can purchase a new oven for about the same price. As the control panel is located just above the largest burner where water is usually heated to a boil, it receives a lot of steam. I visited a local church second hand store and purchased a countertop microwave and used it while I found a good solution. I decided to let it dry out for a few days and lo and behold it worked again. Unfortunately it only worked for a few hours, sometimes a full day and then I needed to let it dry out some more. I purchased an extension cord with an on/off switch and hooked it up. Now I can stop the electricity without having to climb up on a chair to pull the plug. Once I was set up with the easy on/off switch I could easily reset it. After about a week of resetting, it got the message. It has been working properly for over two weeks now with no failures.

My GE over the range Microwave has broken about 4 times in a years time. My warranty company American Home Shield (AHS) has decided that instead of replacing this piece of garbage, its somehow worth it to keep on fixing it, which is apparently their MO for all their customers but I digress. After the latest breakdown (microwave lost power completely), I was referred by AHS to GE Appliance repair. Thus began the nightmare. The tech that showed up was incompetent at best. He showed up, looked at me, made a grouchy face and proceeded to walk in the kitchen with an attitude like he was doing us this massive favor. He opened the microwave door, closed it, opened his computer and ordered 10 (yes 10) different part. Again, he literally just opened and closed the door - did not disassemble to see what part was actually messed up. No diagnosis done of any kind. He scheduled to come out the week after that - didnt show up because I missed his phone call. Btw, I called him back pretty immediately and he didnt pick up. After being on hold for about 35 mins (which is clearly the GE standard hold time), they tell me the guy has left the area and they need to reschedule me for a week later. The day before the 2nd appointment, they called to reconfirm and then the morning of, I called, stayed on the standard 35-40 min hold and reconfirmed he was still coming and was told he was on his way. Well, the appointment time came and went and he failed to show up YET again so I called to ask wtf happened. They said he didnt come because I canceled the appointment thru an automated call. This time the idiot didnt call me like they always do. I asked for proof of this alleged automated call that was placed to me and they said no call record exist and so while it seemed like a system glitch, the tech already left the area and theyd need to reschedule it. I told them, No, thank you. Got a local repair company to come out the very next day. Turns out, out of the 10 parts that idiot tech had ordered, only 4 had arrived while the invoice still showed 10 being shipped. Let me clarify this: All these issues stem from GEs entire company: From manufacturing crappy products to HR hiring incompetent techs to customer service being absolutely nightmarish to supply chain not sending parts that are being ordered. And if you can somehow get their alleged consumer advocate department on the phone after a 40 min hold time, they dont give a crap either. All these employees MUST hate GE to drive customers away as far as possible. I own a business and I will never ever EVER buy GE again.

I have a over the stove microwave. I went to pull out the filter to clean, and one came out no problem. The second one fell apart. I got online today to replace $38 plus $6 S&H for one!!! It was the first time I took it out. I called GE told them I thought it was B.S. They said, No problem, we will give you 15% off and free shipping. Only problem was they wanted $47. I have 3 GE appliances. When its time to replace I will NOT be buying GE.

In 2008, after waiting 30 years, we remodeled our kitchen using both a GE Range & GE OTR Microwave, model # JVM1850. Last week, it started making a loud noise when started and wont heat. From reading online it sounds like the magnetron went. Everything else, fan, turntable, lights inside and outside work, but wont heat. I called in for service to find that it would cost $89.95 to have them come out to diagnose it. Also read that a magnatron is between $150 - $200, and used to be warranted for 5 yrs. New GE microwaves only carry a 1 year total warranty. So they know they are supplying junk to us. Had to just bite the bullet and replace it. People cant afford for appliances to only last this long, at the price they are charging. I am not only upset at having to spend another $450 only 6 1/2 years later to replace a microwave that was lightly used, but GE has chosen to change the look as well, so it no longer will match the range it sits above. When I was remodeling, I read so much about matching appliances... not matched anymore. Totally disgusted.

Weve had our new over the stove microwave (GE Profile Microwave Oven PVM2170SR1SS) just over one year and the oven light went out. The owners manual has no information about how to replace the light. I called GE customer assistance office and they said it requires a technician to come to the house to replace the bulb. A service call would cost around $95 minimum. This is a ridiculous requirement to make consumers do a service call for an oven light. The owners manual does show how to replace the charcoal air filter, if you use one, by removing the plastic cover across the top of the oven with the door open. Guess what? I removed the two screws holding the plastic cover and sure enough, there was also the access to the cover to access the oven light. You just remove the one screw and the small cover plate can be removed! Be sure to turn off the power to the oven before removing the small 50w Halogen G8 light bulb (Home Depot $5.00). My complaint about GE is that they do not give the homeowner information about replacing this oven light, but instead require you to pay for a service call. The irony is that the owners manual tells you how to access the filter by removing the plastic grill and thats how you also access the panel to replace the oven light bulb. They also tell you how to replace the light bulb that provides light to your range, so it cant be a safety issue about replacing light bulbs. Requiring the consumer to request a service call for $95 just to replace the oven light, when GE could have easily put the procedure in the owners manual, is a real consumer ripoff!

I have had the GE Profile for approximately 8 years with no Issues. I learn something new it will do every now and then I had no idea was possible. I stillHave not conquered the convection baking and that is my fault. I need to use it more often since it wouldn’t heat up kitchen like the range does especially these hot summer days in Texas.

One needs to be a contortionist to replace the under light bulbs on this microwave. It is a TERRIBLE design. Why werent the sockets placed so that the prong holes could be visible? One has to do a back-bend over the stove top and then the socket holes are still not visible. DO NOT BUY THIS MICROWAVE. DONT BUY THE STOVE EITHER. IT IS DANGEROUS. THE KNOBS TURN EASILY AND OPEN THE GAS.

I purchased new home with new GE appliances. The dishwasher from day one has been a problem. It constantly leaves water droplets inside on top, sides and door of dishwasher as well as all plastics are covered in water after even using heated drying selection. I was told after 2 visits by GE repair that it functions as designed. We have water softener, use rinse agent and quality dishwashing detergent, and the water temperature is within acceptable range.

Combo microwave and convection oven - its great. Having a stainless steel interior makes it easier to clean than a plastic interior. Prefer a touch screen to a dial but it works okay. Would definitely buy a similar model if I had to replace it.

I have a new house (2 years old so out of warranty) and the kitchen has GE appliances that I choose. I hate, hate, hate them all! I have had problems from the first week in our home with the stove, microwave, refrigerator and dishwasher. I am so sorry I choose this brand! Today my dishwasher (for the 3rd time) isnt working. GE wanted to send their tech in a week. Then another week to get a part. I am so frustrated that I said forget it and called a local repair company. This is Friday, they will be here on Monday. I spent 2 hours on the dishwasher today. They had to replace my refrigerator and cooktop. My microwave went out 5 days after we moved in. Took 2 weeks to get it fixed. DO NOT BUY GE!

This review is related to the Monogram 2.2 Cu. Ft. Built-In Microwave Oven model #ZEB1227SLSS. The GE site: https://appliances.monogram.com/us/specs/ZEB1227SLSS indicates in two places that the built-in trim kit is included (and one place where it is listed as additional), yet GE has confirmed that in fact, the trim kit is an optional add-on with a $325 additional cost. Calls to GEs consumer line have been disappointing. Me: Your website says its included, and is in a section with other features that are in fact included but not additional fees; GE: We have confirmed that the trim kit costs extra. We have, in fact, purchased the oven and are awaiting its installation, and I have other experience with GE Monogram appliances so I expect this to operate well. But I cannot understand their reluctance to acknowledge this error on their site. Potential buyers, please beware of this issue.

I purchased a GE microwave and had 3 different problem with it. They sent a service man out and he could not fix the problems. Now GE said they are closing the case even though they know I do not feel the problem has been fix. My other GE microwave, I really liked until it stopped working around 8 yrs old. This one is a piece of junk. It is an over the stove microwave so I cannot just take it back to the store. I would say GE has really gone downhill over the yrs. This will be the last GE product I ever buy.

Bought GE range microwave JVM3160DF3BB11/16 from Lowes. Tripped the breaker. Replaced the breaker with a new. Would immediately trip the breaker as soon as you pushed the start button. Last time it tripped the breaker oven went dead. Wont even light up. Junk. Do not buy made by Haier in China with the GE name on it.

I bought the GE microwave from a GE dealer. We were very impressed that it is also a convection oven. It bakes, microwaves and even toasts bread. The oven had not disappointed us any way. I would recommend it to anyone in the market for a microwave.

My GE microwave works perfectly for microwaving and baking. It is also a convection oven and it works as well for baking as the microwave component does for microwaving. It is roomy and accommodating. Ive had the microwave for 10 years and have never had a problem with it.

We have a GE Advantium Microwave. It is our second model (we moved and left the first one behind). It is spacious, has an intuitive menu system, cooks extremely well, also includes a convection oven feature that we use to great advantage. The nicest microwave weve ever used (and weve used plenty of them).

Today my GE black microwave with rack mounted above the stove, caught on fire by itself. My husband and I smelled a chemical like smoke. We went in the kitchen and we saw fire in the microwave. We put out the fire and was thankful that we were home. If we were not home our house would have burned to the ground. The microwave was not in use at the time of the fire. I plan to contact GE about this dangerous event. My asthma has gone crazy since this horrible situation happened. I just want to let people know that GE microwave will catch on fire without being in use.

G.E. Spacemaker over the stove microwave. This is my second microwave of this type in 14 years. The first one lasted only 5 years. Im satisfied with the product albeit the price tag is too high.

First of all, I wish I had seen this site over two years ago and I wouldnt have purchased a GE product. But, that is spilled milk. My two year old microwave, GE 1750 over the range, started running on its own. I disconnected it and called GE and asked if they had experienced any problems with their product and if this was a fire hazard, the nice young lady put me on hold and did research and stated that no reports of a fire hazard or running on its own. My husband encouraged me to do my own research and guess what? shocking, I was lied to! There are reported fires on the news and a law firm has a class action lawsuit against GE! I guess because this appliance wasnt in the nice young ladys moms house it wasnt of importance to inform me of the fire hazard? GE is off of my list of products I would buy!

We normally purchase LG appliances but this time we purchased a GE Profile induction range and GE Profile above range microwave oven. The relay went out on the microwave oven about six months after we got them. Their website for scheduling service is absolutely horrible and didn’t work multiple times and when I was finally able to schedule, it was two weeks out. I then called but was told I couldn’t get an earlier appointment. So we waited the two weeks, then they had to order the relay. GE waited until the part was delivered to us to schedule the return visit - over 2 1/2 weeks later! So at this point we are without our new microwave for over a month and a half. Moral of the story is never ever to tempted to buy from GE, LG appliances & cust service are great.

Touch panel gets too hot from the stove and fails. Have to unplug it all the time to reset. Door handle unscrewed and inside coating is peeling. Had repaired three times. When least expected, I have to empty the cabinet above to reach the plug.

Our dishwasher has gotten very warm mid-cycle and now trips the breaker in the house each time we run the cycle. The problem became evident in April 2012. We have called in a GE repair person to fix it and they said it was a heating issue and not repairable. We have not used it since, but have not replaced it with a new one yet. In August, we read about the recall of a similar model number manufactured within same time frame. Our machine model is PDW7300J03WW, the recalled model is PDW7. Our machines serial # is **. Strangely, the serial number is not listed in the recall, even though symptoms are exactly the same!We have called GE Consumer Affairs at 1-800-386-1215 four times, the most recent today, 9/14/2012. Each time we call, we are left on hold for 59 minutes only to be disconnected automatically! I am sending a registered letter to GE CA with a copy of this link and intend to contact my local news if I do not receive sufficient response within the week. Does GE need to see an actual fire report from my fire department or worse in order to get their attention to replace the unit? It is disgraceful and extremely dangerous.

GE Profile Microwave/Convection Oven JVM1790WK, over the range unit, CAUGHT ON FIRE while microwaving water for coffee. One of the four prongs that holds the oven grid in place started flaming wildly and smoking after about one minute of microwaving. My whole kitchen has an acrid awful burning smell. This is my second unit for a small kitchen, and I will be lost without this. The first one I had the handle fell off. This one is too dangerous to use. These units cost $600!!! I cannot afford to replace one every few years. Maybe this model and brand is bad news?

If you have a choice, run away from GE like the plague, because if you have to make a warranty claim, it may become a nightmare. I purchased a new home May of 2015, and my wife and I paid for the appliance upgrade to the GE Profile, which werent cheap. Less than 2 months I noticed that the microwave had a burn spot on the bottom of the door where it sits against the exterior of the microwave, the paint was burnt from the metal, and the rubber seal melted. I did not think too much of it because the microwave still worked and unless you opened it you did not see it, so it wasnt so much of an eye sore. Fast forward to January 2016, my wife informed me that the microwave stopped heating, and that she was going to put a ticket in to New Home Warranty, I informed her that we probably need to go to GE directly as I knew that is what they were going to say. So I called GE and put in a Service ticket. They informed me that it was going to be a little over a week before anyone would be available to come look at it, to which I was OK with. The repair guy finally came. I explained to him in detail what the issues were. He opened the microwave, closed it back, wrote some things on his computer, and told me that he ordered a part called the magnetron tube, which sounded like something from the transformers. He told me it would be a week before the part would be ordered, so I asked him if it wouldnt be easier for them to just replace the microwave. He told me that it is a warranty repair and they have to try and fix it first and if not, then they will. The evening before the repair guy was supposed to show up to change the door and the magnetron tube, I got a voicemail stating that the part will not be received until the evening of the repair, so they rescheduled me for 2 days later. GE just assumed that I would be available, because I probably sit at home all day waiting for service repairs. I called back the number to see what was going on. I was adamant that they replace the microwave, because by this time it was already 3 weeks without a microwave. And with small kids in the house it was very annoying to have to put a pot on the stove every time you needed to heat anything. After 45 minutes, I was still nowhere with them, so I ended up sticking with their new appointment window. I was leaving for work 2 days later when I noticed the repair guy at another home in the community. I thought to myself why couldnt he have done our repair the same day if he were already going to be in the neighborhood? About 45 minutes later my wife called me and told me that the repair guy showed up to repair the unit, that they were supposed to repair a day later, only to be told that the damage on the door was caused by arching, and that it will happen again so the microwave is non-repairable, so they will have to replace it. He told my wife that she will be receiving a call from the warehouse within 24 hours to schedule the replacement once the microwave is available, but she could call the warranty repair department to see if they could expedite it. After another 25 minutes on the phone going back and forth we were told that it will be about 7-10 business days before the microwave may be available. Now it is good to note that the warehouse where they stock the product is only 2 hours away from where I live. So by the count of it by the time we receive a new microwave, it would have been about 5 to 6 weeks from the initial call to get the issue taken care of.

My husband and I replaced all the appliances in our new home 4 years ago with GE Profile double oven, cooktop and built in microwave. All the appliances are of poor quality and do not cook the way we are accustomed to. But the microwave has had a particularly bad history. Within one year, it completely quit working and we had to replace several fuses and a board. Over the past couple of months, the keypad continually quits working and we have to climb up on a stool, unplug the microwave to reset it. Only then will it work for us to heat something. However, the keypad does not accurately reflect the task we are trying to use. I have had many microwaves over the years and I have NEVER had to repair one before. This particular brand of microwave was produced in Malaysia in July 2008. Very, very poor quality. No resolve from GE or from Sears where we bought it. I am done with GE and with SEARS.

I have many other things to do other than to voice my extreme and total displeasure with your company. GE - Huge Company, Small Customer Service. We purchased a GE microwave oven from ABT electronics in about August, 2013. In October, 2014 we had issues with the fan remaining on while the door was closed. Called GE. They said the unit was out of warranty by about 2 months. We felt that was a short period of time and that we called as soon as the issue became chronic.Had three service calls where the techs tried to fix a simple problem. First tech walked through our living room with dirty boots. Didnt fix the problem. Messed up our carpet. Bad attitude. Second call, two techs couldnt fix the problem. Said it was a door issue and they made some superficial adjustments. Problem not fixed. Third call, two more techs. Same result. In the meantime I tried to convince GE that I didnt want another service call. I wanted a new unit. No luck. I was offered a discount to purchase a new unit for around $300 or so. Im sure they spent more money on service calls than a new unit would have cost in terms of dollars and the reputation of one of the worlds biggest companies.Now, the fan for the unit stays on almost all the time after the cooking is done. Is this the best GE can do? If so, thats pretty sad. Tried to reach someone in sales who would get it. No such luck. DONT BUY GE AND IF YOU HAVE ISSUES DONT RELY ON A FACELESS, CLUELESS CUSTOMER SERVICE DEPARTMENT TO HELP IN ANY MEANINGFUL WAY.

We upgraded our appliance package when we bought our village builder home 8 years ago. All GE Monogram appliances have rusted and now need replaced. New liners needed in oven which was so rusted we couldnt get the screws out to replace the originals. Was told by GE customer service rust to be expected when cooking. It creates steam and food particles can cause scratching!!! Maybe it should be steam proof especially a microwave. Even the door on this is rusted! Why the shelf ends in a freezer are rusted not sure on that one! Will NEVER buy this brand again and shame on them my upgraded appliances dont even make it to 10 yrs. A disgrace. My mother just replaced her 20 yr old oven. What is wrong that nowadays things dont last 5 minutes? Shame on you GE not recognizing a definite flaw in your products.

I have purchased a GE microwave/convection oven 7 months ago. A month ago, the control panel broke down and it would not turn on. I called up customer service and a technician was sent after a week. They have diagnosed it and the motherboard needed to be replaced. The said part was ordered and I was told it would be delivered in 2-3 days and a service will be scheduled in a week. A week came and no parts showed up. I have called up customer advocate and they assured me the said part will be delivered in time for the service appointment.Unfortunately, when they came, the said parts have not been delivered and I was given the lame excuse of systems failure; the request has not gone through their system. So the technician assured me that he will put in an overnight request for the said parts and the oven could be fixed within the week. He even gave me his work and cell number for me to call if I have any inquiries. But he never picks up or even returns my calls. So another service appointment was scheduled and parts were delivered, only to find out that it was the wrong parts, supposedly for another customer and for a different microwave model.Its really frustrating when people keep on reassuring that they are going to get it done, but has done nothing but lip service. Its been over a month and my microwave is still a broken microwave. I have learned my lesson and will never again in my life time purchase a GE appliance. PS: I should have listened to the Home Depot guy that sold me this microwave.

Negative 5 stars. I purchased a GE over the range microwave oven, JVM2052SN1SS, just over a year ago and had a service call to address a lack of exhaust about a month after my purchase. In summary, the tech said it would not function as a dedicated exhaust hood and nothing can be done. 14 months later, the key pad began malfunctioning. Also, the moisture sensor that the operation manual stated will automatically start the exhaust fan, never worked and every time we cook, moisture would build up between the glass on the microwave door.I called GE Consumer Relation today and they will not address this issue free of charge. I will not purchase another GE product because GE dont stand behind their products.

My experience with GE over range microwave oven as follows/ Unit Mod.JVM3160DF3WWW. Ser.#GH260692A, this unit was purchased April 2017, February 2019, unit began to disconnect itself during normal use. This was done by way of throwing 15 amp breaker. No satisfaction from GE, NO extended warranty purchased, guilty as charged, contacted elect. tech. No idea of problem, #2 elect. problem in door sensors of which there are numerous, notice black residue on duel latch on door caused by door latch device rubbing on unit latch receiver cost to discover which sensor cause and replace one or all 250.00.We have been limping along for two months with frequent trips to basement resetting breaker (which we had replaced) next move, purchase NEW MICROWAVE. Let me be very direct if we wanted JUNK we would buy Asian made, THAT being said, there will be NO...General Electric products in this house. This is our second GE product BUST, 100.00 advertised by manufacturer. Never delivered! But hey we are just small time consumers. What might else we expect.

Our Spacemaker microwave, which was installed over the stove August 2008, suddenly stopped heating food. My husband called GE, and their phone advisor advised us the microwave was under warranty. She said her computer screen showed our product registration, and she also saw we owned three other GE products. Fast forward, the GE repairman came and said the microwave repair cost would be around $400. The heating part wasnt under warranty nor was the labor. Mind you, the entire microwave (new) was under $400. We called the GE service center, and they refused to honor what their representative had told us. The most they offered was 50% off. I dont accept the premise that a new appliance should only last four years. I will replace my unusable microwave with a competitor’s brand and will pledge never to purchase a GE appliance again. I will also sell my GE stock, for I now understand why its going nowhere.

My GE microwave also has paint peeling off the top inside and bottom with rust as well. And cannot be repaired but not one person has said they were sorry or even owned up that it is a fault in paint. This is disgusting to think about this stuff falling into your food!!! This is not safe at all and 10% off new unit is not nearly enough considering they are up to $3000.00 now for microwave/oven unit.GE does not stand behind their products and it shows!!!!

After many searches trying to do due diligence, we bought a GE dishwasher online Nov 2014. It was delivered and installed two weeks later. The day (Saturday) after delivery we loaded it and started the cycle; water went in, the circulation pump started and then the machine stalled. The machine was reset pumped out, restarted but no further improvement.Called the GE service number and after a 20 minute wait was informed that a request would be placed to a local service company. Monday the local service company (30 miles away) called to inform us they had to reject the service request and that GE would set up another. Three days later GE was called again. They were unaware that the service request was rejected so had not attempted to find someone else. They could not get another company to respond and told us to arrange the service call ourselves, pay the bill and submit it to them.My wife and I are now wanting to return the machine but were informed we would have to go through the local Home Depot. They informed us that we would need to have GE arrange it. GE was called back and informed us that the dishwasher could not be returned as long as it could be repaired which leaves it to their discretion. The process to arrange these things took a long time, many delays and many phone calls back and forth to Home Depot and GE. The calls to GE often took 15 minutes to get someone who would forward the call to the service rep which placed back in another 15 minute queue. Do not believe that Home Depot will take returns. The advertising makes you believe they will take but they do not without GEs RGA which GE is reluctant to provide. Avoid GE. I am not the first to find out that GE warranty (one year) and service is poor and that they are more than willing to wait out the warranty to leave their customers with a possible lemon. Other dishwashers are available with 5 year warranties.

No issues yet. But only had for 6 months so time will tell. Read a lot of negative reviews but none here. Bought in Nov ‘18 from Home Depot. Delivered and installed on time. Replaced 13 yr old GE appliances that were still working.

The side panel of our built-in GE Profile microwave 1999 caught on fire when my daughter was using it. It had a faint glow behind the metal plate. Then, it became flames quite quickly. A flash and pop was the ultimate end before we turned it off during the test. It had been working fine until the fire. This is a definite safety issue. Now that I know the microwaves have been faulty, it makes me concerned about the GE Profile electric stovetop burner. I have noticed it gets extremely hot and doesnt seem to want to turn off!

Our Profile over-the-range microwave failed after 2 years. (Warranty was for one year!) One day it suddenly died. The repairman ($100) said repeated twisting of the wire from the oven to the door (which contains all the electronics) is inevitable with opening and closing. The wire often breaks within its insulation: a bad design fault. No question of replacing the wire; we would have to order a new door, for nearly $400 plus $200 for installation, which requires 2 service technicians. This is more than the cost of a new OTR microwave. He advised us to get one with the controls beside, not in the door. Unfortunately GE is the only company that makes a microwave in the same colour as our range.

The protective lining inside the microwave is coming off in a number of areas and the metal is visible and rusted. Is it hazardous to use the oven which is otherwise working? I contacted the Consumer relations department of GE and was told that its not repairable and offered only $25 as rebate to buy another one from them or any other retail store. I visited a couple of merchants, online and in their store, shopping for a similar product and got a price range between $250-450 plus $110 installation fee for a similar OTC microwave oven. We have all other appliances at home from GE and this does not give a good confidence about the products from GE.

We purchased a black over the stove microwave from GE, the oven has great preset buttons and it extremely easy to use. It looks sleek and works great. The only issue we have had was a few months after purchase we tried to change the bulb for one of the lights and the entire mechanism crumbled and fell out so we only have one light now over the stove. Disappointing but everything else works great.

GE continually shows us why they are failing as a company. In just this last year I have replaced a less than 5 year old GE microwave, three separates parts to my GE monogram refrigerator, and now this one and a half year old dishwasher. The only appliance that GE makes that hasnt broken is the stove/oven that is over 10 years old and shows no signs of weakening.I purchased the upgraded stainless steel model that contained all the bells and whistles. It lasted 1 year and 3 months before the entire control panel stopped working. We utilized the dishwasher about once a week or once every two weeks in a two person household. Hardly a rough environment for a 700$ appliance. The repair costs was quoted for 99$ just to have GE look at it. The control panel was 140$, plus additional labor. This amounts to over 280$ to repair a year old product. I advise buying LG or Bosch.

Bought a GE microwave and arranged to have it installed. Kept it in sealed box for 3 days until installer appointment. Opened box to find a crease (dent) in door. I phoned in to the GE warranty depot and they informed me that I only had 48 hours to report and as such was out of luck. They indicated that it is clearly stated in the Appliance Manual under the warranty section. Too bad that the Manual was in the sealed box. No warning on the outside of the box. On top of that the individual that I spoke to at the Warranty Depot was very rude. No more GE Appliances for me. Be forewarned.

I cant remember the exact date of purchase for my GE Spacemaker microwave oven. I have a receipt somewhere, but I have receipts for repair dated 2002. It is for a door seal gasket for the microwave. A model JVM60 GE Spacemaker installed over the range.The microwave worked perfectly for several years. Then one day, when I pressed the start button, I noticed a small fire inside the window above the control panel where the time is displayed. I called repair man; I was told that it was the circuit board, and GE was not able to send repair spare part. Since then the microwave is only good for displaying the time, and storing my everyday pan. I do remember paying $400.00 for this microwave because I purchased it at my employment. It would seem to me a company making a $400.00 appliance would be backed by a circuit board, which they know would go bad in a short time. Thats why they only had a one year warranty guarantee.To show you the difference in a microwave appliance, I purchased a small counter top microwave in 1997; it still works like a charm, and I use it every day. From the negative reviews I read on these Spacemaker microwaves, I firmly believe there should be some compensation to us consumers for the money spent, plus the hazards we experienced. If that is not agreed, then all of us consumers should file a class action suit against GE.

About two years ago I moved into my condo and as a housewarming gift my sister gave me money to buy a microwave oven. I bought a GE over the range microwave. Well it quit over two months ago - really disappointed. I bought the next one but now after reading all these similar experiences I am sorry I bought the same problem.

I loaded and ran the GE Profile dishwasher in the evening. Later that evening, putrid odor of undetermined origin was noted in the house. I searched throughout house to find the cause, but it was not located. The next morning, the dishwasher was found to be extremely hot on the outer surface (door) and countertop. The heated dry light was on along with the start button, which would not reset or turn off. The unit had to be disconnected by turning the electrical breaker off. All contents were either melted or had a strange brown film, along with broken tines and melted silverware rack in the dishwasher. Even the water dispenser in the bottom of the dishwasher was melted or broken. A GE service representative was called and his report stated: Unit was left on for too long and heat caused excessive damage to the product. Due to excessive damage, unit is non-repairable. He shared with me he had never seen this much damage done to a dishwasher. I spoke to GE consumer advocates twice and their solution is to provide me a discounted price on a new appliance and the email address for formal complaints. When I inquired about if there had been resolution to the cause of this problem because I wanted to make a formal complaint, I was told there is not a safety issue with the heating unit. I then spoke to a GE resource person in recall and she shared with me that it is a known issue of overheating and destroying contents, but it has not caused a fire. Igniting a fire is a justification for a recall - can we not be proactive? This department is working with me and ensured that in newer models this potential hazard does not exist. But other consumers who have purchased in this model (PDW9280N20SS) should be aware of the potential fire hazard. Everything was very hot inside and out. Consequences: the 3-year-old dishwasher (that I use about once per week) was totally ruined and I inhaled potentially toxic fumes for over 8 hours.

We built our house and purchased a NEW close out Advantium Microwave. Due to delays we were not able to get into the house and use the appliance until literally 1 month after the WTY expired. The KEYPAD is shorted. There are a number of these complaints for this microwave - so we arranged for service. $375 dollars later - it was ALMOST working and the repair service determined that a new keyboard would be needed. 5 mos later we are kindly asked to take a refund of our repair bill and forget the whole thing - the part is not available! REALLY?! $2000 for a microwave, and you dont even support it?! Last - LAST time I put trust in GE. SCB2000FBB 03

My life partner/bf moved into a semi flipped 10 yr old home. Every single appliance required to be replaced, everything from refrigerator, stove/oven, to dishwasher. We researched every appliance we purchased, a lot of time and effort along with reviews from various reputable reviewers, pointed us to the GE GDT DISHWASHER. Who can go wrong with three tier washing amongst jetted water bottle washers?After a 1 1/2 yrs in the top spinner completely separated from its housing. We googled the problem, GE said it was a faulty design, yet no recall. The door lock began to fail, googled the repair fix, another fault design, yet again no recall. Upper plastic door trim broke in half, solution, replace the entire console. Guess what? My solution here on out is to not buy GE products. If two years is all you get with a GE product, I am out! Done with your products that once lasted 10 to 15 years. The fact that have to research another DISHWASHER, absolutely pisses me off. I dare you GE to win me back!

I will never purchase GE appliances again, have trouble with refrigerator/stove & dishwasher. Dishwasher is so loud that you cant be in the kitchen when its on so I only use it at night. It doesnt clean good & everything about it is wrong!

The microwave oven that I’ve been using works real well and it’s not that expensive. It’s also a convection oven at the same time. The only reason I didn’t give it a 5 is, I rarely give that high # to anything with rare exceptions.

When you use the vent fan it is very loud even in the low position. I would also like to see a brighter bulb under the microwave. I dont have much more to say except that the oven functions well otherwise.

I purchased the micro from Sears. This is the replacement for one that was provided by the builder. The G.E. now needs replacement. Will work for limited periods of time. I have used it more than my stove to cook chicken, beef and whole meals. I will be replacing it with a new G.E.. The current one has lasted more 10 years with very heavy use.

We bought Cafe series appliances less than 4 years ago including dishwasher, fridge, stove and microwave. These are not cheap appliances. We also bought a service contract with them. When our dishwasher broke a couple of weeks before Thanksgiving, we called service to have it looked at. After 3 trips and over a month later the dishwasher is still not fixed. Each time we tried to make an appointment we were always given a date 1 week out and a 4 hour time window, but each time the technicians showed up late and once even 3 hours late despite the 4 hour window. The fact that after so many visits and part replacement the dishwasher is still broken says a lot about the quality of the product and its maintainability. All customer representatives work like zombies. The problem with GE lies within the culture. Nobody cares. The service contract is a total waste money.

I bought GE OTR microwave in December. It is exactly one month old now. My model no. is: 9195SVC. It looks good, but I find the fan very noisy, even when it is at low. My range hood which we had in the kitchen prior to this microwave was very quiet at low and only a bit noisy at high. I do not know if the noise is because I have steel exhaust pipes vented out. Rest is O.K. but given that others have reported problems in 1-2 months, I am still nervous.I bought this product at Sears with an extended warranty, which is some relief. However, when I was shopping for this at Home Depot, the salesperson told me these microwaves last only 4-5 years. One good thing about Sears extended warranty is that if it is not used over the five years, they refund the warranty payment (with taxes) in the form of a gift card and they were also cheaper than Home Depot.

Touch pad on GE CAFE over the range microwave started failing within first 2-3 years. Now, 6 years later, it has completed failed. Repair part alone (not including service call) is almost $550.00. Pure junk...made in MALAYSIA!

Today I heated some spaghetti sauce in my microwave and it splashed, so I wiped it out. My microwave is built in and was pretty new and in the house when we bought it 4 years ago. It is in the base counter so I have to reach down to clean it. l havent had a problem with it but when I wiped the inside top I felt bumps and when I looked at the cloth to see what was on it, there was paint on it. That has never happened before so I of course looked and there is a fair amount of peeling paint in one spot. I have had microwave ovens for many years. Never had this problem with any other brand. What is that?? Can it be fixed? Is it dangerous???

This GE CVM2072SM1SS Microwave (over-range model) worked fine for five years. Then, we discovered the plastic film over the touchscreen starting to peel. After a bit of wrangling with Consumer Relations, they sent me a replacement touchscreen. The LCD didnt display properly, so they sent me another one. It worked for three months, then in the middle of programming to reheat some food, we got the following error message: Control Fault, Shorted touchscreen - F10. The control has detected a shorted touchscreen and has shut off the oven. It may still be possible to use the oven. However, if this message continues to appear, your oven will require service.The only way to clear the message was to unplug the unit. No amount of replugging in cleared the message. I called GE and they said they would replace the entire unit with a new model under some program they had. Sounded fine to me. I left the house. When I returned, I received a message that their representative called back to say they would not replace the unit, since the program had expired. Huh? I called again, and after a bunch more wrangling, they agreed to send a service tech out and replace whatever needed replacing or fixing at no charge. Of course, they never really made a notation of that, so when he got here, he had to get on the phone and sort it out. Finally, he replaced the touchscreen. Lets see how long it lasts this time.

I purchased a GE microwave from PC Richard and Son in 2011. The microwave is mounted above the oven. On March 13, 2013, the microwave (model JVM1750DP1WW) sparked a fire inside while my daughter cooked a waffle. After I contacted GE via email, the case manager (Misty) sent a technician to my home to inspect the microwave. This was free of charge. The technician claimed the microwave was able to be repaired and he needed to order touch up paint and a few parts. I was shocked that the tech claimed this was a simple repair and able to be fixed. I said, You need touch up paint? This is going to look horrible. How safe can this be after having a fire inside? He claimed it will look good and I would not notice the paint. I spent $411.00 on this microwave less than 2 years ago. I dont think I should have it fixed and touched up with paint to cover burn marks. The microwave went on fire. I dont want it fixed. Its not safe and should be scraped for safety regulations, not repaired and touched up inside with paint. The tech ordered a few parts and I immediately called the case manager Misty to stress to her my numerous concerns on the actions of the technician. I made clear that I was not satisfied with my microwave being fixed and painted when it went on fire, but would like a replacement. I told her I could understand fixing it if it was a broken part or electronic device, but not a fire. She agreed that she also would not like to have a fixed microwave in her home, but that GE can sell me one at a lower price of $150.00. Really, do they need the money that bad that they cant stand behind a dissatisfied consumer when their product went on fire? This could have been so much worse. Lucky my daughter was in the next room. She smelled, heard the fire and stopped the microwave. I paid the $150 just so I can have a working, new, safer microwave in my kitchen. But this is crazy and not good business ethic on GEs behalf. This should be set as a recall, not a repair. I contacted the service manager again stressing my complaint and feelings about paying this fee for a new microwave. She said again that if the technician says the microwave can be fixed, then theyll listen to the technician and fix the item. Well this seems a little one sided since the technician works for GE. No brainier. What do you think he is going to say?

We purchased a GE microwave/convection oven which developed peeling on the inside top of the microwave. GE contacted me and offered a replacement ($300 toward a shelf model or prorate the microwave/oven). Why would we take $300 replacement when we paid nearly $3000 for this oven???? So we took the prorated one directly from GE. We felt confident that we would not have a repeat of the problem. The oven was manufactured in December 2012. After it was delivered, I noticed a rough area on the turntable; and after the oven began to peel AGAIN on the second oven, I believe that the rough area was due to a remanufactured part on the oven.Now we are stuck with another microwave/convection oven combo with the same issues as the first oven. I never used anything harsh to clean the oven and now this happens again. Why cannot this company manufacture an oven that will not have defects in it??? I am tired of peeling paint on a second oven when I have done nothing except pay them for 2 ovens. Why cannot they use stainless steel interiors, and this would stop the many complaints that people make about the product. I would NEVER again purchase another product from this company. The products I have purchased have been inferior. I paid for two microwave/convection ovens and still have one that is inferior!!!!

We moved into our new manufactured home in May of 2013. That is the month our above range built-in GE microwave was installed. In October of 2013, one of my sons heated a frozen chicken cordon bleu serving for 3 minutes, 45 seconds, according to packaging directions. He said that some of the inside of his food was cool, so my other son put in his serving for four minutes, zero seconds. All of the packaging was removed and each serving was placed on a separate Corelle plate and covered with Glad microwave-safe plastic wrap. While heating the second serving, the microwave started on fire. Fortunately, my son extinguished the fire before it spread. The food did not combust. The fire seems to have started from the ceiling behind the fan. The entire inside of our microwave is clean except for the soot that billowed out from the center of the ceiling. When the service tech came, he scrubbed the soot off of the ceiling with some paper napkins (which he left inside of the unit) and said that the microwave was a total loss. He also said the fire was caused by misuse, because plastic wrap is not meant to be used in the microwave, therefore even though the fire happened within a year of purchase and installation, our warranty was void. I asked GE to get a second opinion and they agreed to send a third party servicer (A&E) who stood me up three times! I finally got to schedule a GE tech to come at the end of December and they sent the same guy who said the fire was our fault! He told me that he never said plastic wrap is not meant for the microwave, but that we are being dishonest because fires only start when the food is left in the microwave for too long. He accidentally let it slip that he is seeing the same problem with GE microwaves in a lot of new construction for student housing in Tallahassee. (We live 20 minutes south of there.) He attempted to recover GEs reputation afterward by saying that of course it was the students faults, too, for misusing the microwave units. Anyway, GE has graciously offered to sell us a new microwave at slight discount. Haha, no thank you!

Microwave and convection oven together...perfect for heating food or baking. Very easy to operate. G.E.profile. Mounts over the stove with an exhaust fan and lights. Also has a rotating plate in it to heat evenly.

On 05/20/2014, our GE microwave over the stove unit burst into flames. My wife was using timer and walked away then turned around and heard the microwave fan start (spontaneously). Then she observed flames/smoke reflected in the Microwave window. She observed the interior of the microwave was aflame. The fire was extinguished with a rag & water. The burning items appeared to be plastic/insulation. The fan from the microwave was with the burning insulation on the rotating plate. Had this unit only 14 months during that time the microwave fan would turn itself on for 3 minutes and then turn off all by itself. Happened twice in 14 months. Glad we were at home and were able to extinguish the fire. Called Lennar the builder who put this unit in to take pictures and check electrical. Was told the GE unit was bad to call GE. I know this will be a hassle as others have had this same problem with not so good results.

The microwave is over the stove with a vent. It is about an 1100 w microwave. I just have to eat out a little bit more time here are the ones that are bigger. The price was right there and that I would’ve bought something else.

I purchased a new GE over the oven microwave to replace a 10-year old Spacemaker unit. After three weeks of use with no issues, the unit overheated excessively during a normal use. The heat was so intense that the pegs that hold the racks melted causing a severe burn on my sons thumb. I unplugged the unit fearing further injuries and/or fire. Are GE products manufactured poorly or did I get a lemon? Who knows? Anyone else have a similar issue? I am still waiting for GE to respond.

We bought our new home 4 years ago & bought upgraded GE Profile appliances. To date, the gas range has been serviced 3 times, the refrigerator too many times to remember & now my dishwasher pump has gone out. We found out the pump just cannot be replaced, but all hoses, etc. must be purchased as well. GE is CRAP & I will never even consider purchasing anything from this company again. Knowing it was bought out a few years ago by Whirlpool (I believe) but still remains under the GE label - consumers BEWARE.

Not even a year after purchase of new cafe series dishwasher, stainless lining rusting. Service called, GE tech agrees rusting of lining, GE warranty says not under warranty. Ive replaced screws that show signs of rust with aftermarket stainless screws. Cafe oven has had three front knobs just fall off - two were repaired under warranty and had to purchase extended warranty on third because it was more cost effective. Cafe Refrigerator had drain plate in back of unit completely rust away, tech knew what problem was before he stepped foot in my kitchen, he told us this was common. He caulked some sensor inside fridge box during service, I asked why, his response was its a design flaw and unit will operate better with this modification. Oh and redesign the ice dispenser, its tilted towards the back of the freezer and the ice is dispensed out the front.

I purchased a GE Spacemaker microwave in Jan. 2001. Shortly thereafter, the frame around the door cracked, becoming worse until in Oct 2006 I complained to GE. They sent a $75 credit towards another GE. I purchased another GE in Oct 2006. After a while, the handle became loose. Today, the handle broke off at the base where it attaches to the door, rendering the oven unusable. I dont have kids. This appliance was not abused. I see in looking through the comments that other consumers have had similar problems which would suggest a product defect. My next microwave will not be a GE.

We purchased a GE Profile Microwave with our GE Profile range in 2010. In 2016 we noticed an area on the bottom of the back wall that was peeling. It is in an area where nothing is rubbing or touching it. After taking photos and contacting GE customer service I was offered a discount on a replacement microwave. I expressed my concern that a new microwave might do the same thing--peel. I was told that the newer microwaves have a moisture resistant paint. The area that has peeled is much larger now than is shown in the attached photo taken in 2016. I expected my oven to last longer than 6 years; its a GE Profile and we take excellent care of our appliances.

We had some oil spill in the oven, which proceeded to catch fire. It was a huge fire that burned for a while. But all it took was a little oven cleaner, and it looks like nothing ever happened! The coating and materials inside of the oven are completely fine. It also still works perfectly! I'm amazed. 10/10 stars.

Last fall, we updated our kitchen counters to quartz, and the Jenn-Air to a GE induction cooktop. While it is indeed pricey, the joy of cooking is not overstated here. The quick heat up, the ease of controlling the heat more precisely, and the easy clean up makes this unit well worth it. I love it!

I just built a new home and opted for all GE Slate appliances. No problems so far with microwave, fridge, and stove but the dishwasher has never once been dry or cleaned all dishes. We have had it a little over a month! Today when I went to run it, there was mold growing! I had a KitchenAid for 9 years and never once did any of this happen. From reading other complaints, it looks like Ill be living with this for some time. I will never purchase GE again.

Have a GE over the range microwave oven, MODEL PVM1870DM3CC which started turning itself on for 6 minutes, repeatedly, WITHOUT being touched!

I purchased a Ge profile top of the line microwave installed over an electric oven. After 3 months the plastic handle came off and Ge replaced the entire door. This handle has now come off 3 times. The service tech said it has a plastic connector that weakens over a stove. It supposed to be mounted over a stove. This is just poor design and totally unacceptable for their top of the line microwave.

GE Microwave Model JVM6175EF1ES - On July 26, 2014 purchased as a set stove, refrigerator, dishwasher and microwave. From the beginning I had problems with the microwave with the door had a bad connection and the microwave would shut off. On April 2015 the microwave started working without me starting it and I had look up and I saw sparks on the inside and I unplug it. GE replace it and now after 2 years I have the same problem just started and would not shut off and I unplug it. Both times I was lucky to be home. I would like GE to fix my microwave. I understand it has passed one year but, I think appliances should not break down after 2 years. I would like it fixed or replaced if possible. Thank you for your cooperation in this matter.

We have a GE SpaceMaker JVM 239BV 001 over the range microwave purchased about 10 years ago. Within one year of installation the handle snapped - just as numerous people here have stated. I went to our local replacement parts store and was shocked that it cost $30 for a new handle. The sales person said if I were you I would by the lifetime warranty for an extra $3 because you will be back, I sell lots of these.