I have purchased all new Whirlpool appliances for our new home in March 2009. I have had trouble with the refrigerator door panel and will not switch between ice and water. Cost to replace over $100.00. Now its the range. When turning on the oven, my wife said she saw a flash of bright light and then I turned around and it was smoking up the house! I quickly pull the stove out and unplugged the stove. I then remove the back panel and found the right side of the control panel was burned. Had I not pulled the plug, a fire would have started. I have pictures to prove that! The cost to replace the control panel is $267.00 and that doesnt cover the repair man coming out to test if anything else is bad!

We purchased a Duet washer in Feb 2011. On Nov 2011, it started making a very loud noise when it would spin. We contacted the warranty company, not realizing it was still under the manufacturers warranty. The warranty company came out and took a look and claimed it would be about $1500.00 in parts to repair. We contacted whirlpool and they also sent a service person that claimed the same thing. Both service people claimed that the other did something to the machine and it was the others responsibility to fix it. We have contacted whirlpool and the parts have been ordered. We were informed today that they are on backorder and will not be available until some time the middle to the end of January. When asked why they just dont replace the washer, the answer we received was that was not the policy.

The AquaLift self clean is a joke! Doesnt clean at all! Has to be consumer fraud, calling it a self clean. Ive owned electric self clean ranges for 40 years, that did great jobs. This does zip for cleaning! Unbelievable! Should be a rating below 1 star!

The washer is a lower priced but basic machine with few bells and whistles. However this is what we wanted. Less tech with less problems so for us it works. Does the job it is required to do. Cycles do take much longer than our old machine did. Probably due to water conservation.

I am a senior who has not used the Whirlpool Range installed by the builder in 2007 very much. First of all, I did not like the way the covered jets hid the lighted jets when they were turned on low. Then about 8 months ago, I smelled gas and no one had used the range. I checked the knobs and one was turned slightly without any gas lit. I know that for years the companies were required to have push-in knob before you could turn them for safety reasons (especially children). These knobs barely push in before turning so that they can easily be accidentally brushed against and leak gas, which is exactly what happened to me again today. My daughter was visiting. Neither of us had used the range and when she left, I sat in my living room and smelled gas. I immediately checked the range and the small front jet was turned slightly on. The odor was so strong that I know it had to have been on for some time. Its been an hour and Im still airing out the house. I have used gas ranges for over fifty years and never had a problem such as this. Im thankful that I do not have issues with my sense of smell. Otherwise, I would not be sitting here writing this.

I bought a Whirlpool model GI7FVCXWY00 over and under refrigerator directly from Whirlpool through DirectBuy on April 19, 2010. The unit was a relatively high-end model (over $2,000) that came with a 12-month warranty. Thirteen months after purchase and 1 month after warranty expiration, the ice maker stopped working flooding the kitchen in the process. We called Whirlpool who recommended one of their authorized maintenance subcontractors (GuinCo) to appraise the problem. GuinCo came out, diagnosed that a valve in the ice maker had gone bad and the repair cost us $364. We chalked that up to Murphys Law (repair needed immediately after warranty expiration). Not 4 months later, the kitchen comes up flooded again and again and the ice makers not working. We call GuinCo, the repairman come out and said this time that its a heater and ice maker defect which will cost $643 to repair. He also said that the unit has been designated as having a design defect. We held off on the repair until we could contact Whirlpool for some remediation since it has become obvious that the unit is a lemon. I called Whirlpool, laid out the problems, timelines and potential cost (ice maker failures are going to cost us almost half of what the entire refrigerator cost before the unit is a year and a half old) and the only response they had netted out to was: Sorry, you should have had extended warranty. This is a prime example of an American manufacturer, marketing an inferior product and offering the customer nothing when the lack of quality becomes obvious. I will recommend to anyone I know to stay as far away from Whirlpool products as long as I live.

I bought in 2008 a Whirlpool Cabrio washer because it was the best. It cost me $900 plus 170 extended warranty for four years.This month, my washer showed an f1 code. I call the Maytag store and guess what, they are not there anymore. They closed the store. I called for my extended warranty and guess what, they are not with Maytag and they filed a chapter 7. So, I spent over $1000 in a machine that only worked three years and now I have to buy another just because no one wants to take the responsibility on the warranty. I have to pay another $300 to fix the problem and even doing that, theres no guarantee that it wont fail again. So, and this is to the people of Maytag and their cheats, you may take my money but you lose me as a customer forever. Thank you for nothing. I will keep that in mind next week when Ill be in the store buying another washer.

Really pretty fridge... wish it was just a little smaller. Also wish matching appliances had grey sides like the fridge does. So far it has been a winner.

On 12/27/2013 I bought a Whirlpool hot water heater from Lowes Model NU50T122-403. On 12-13-2015 the pilot went out. When I called tech support on 12-14-2015 they gave number what were call centers or person who returned the calls. So I called a local plumber that I used before. He came out and told me that had to replace the pilot. On the 16th 2015 of Dec. that did not work and told us the heater needed to be replaced. The replacement will happen today I hope with little to no help from Whirlpool. I would advise you to do your homework before you buy a Whirlpool hot water heater.

I bought a Whirlpool French door, freezer drawer on bottom at Lowes 2 years ago for $2,600. The refrigerator needed a new motherboard within the first year and now that it is in the 2nd year, service is required again. The repairman ordered the part and came the 2nd time to replace the part upon receipt. Now it needs the 3rd part since it is still not working. I have a herniated disc in my neck and had to remove everything from the refrigerator and freezer to take downstairs to salvage our food. Now I have to go through the same thing again for the 3rd time after the additional part comes. This refrigerator is junk. I asked Lowes for a new replacement but of course was denied. Does anyone know a good lawyer for this type of situation? I never had a problem with an appliance like this.

I have replaced the damper control unit three times the last three years. The part begins to fail after nine months in used. The temperature becomes too cold in the refrigerator and the food started frozen because the damper door wont closed as cold air flows from freezer to the refrigerator. It adds to the displeasure that Whirlpool is not taking care of the shipping cost even the part is under warranty.

Front Load Washing Machine, Model WFW97HEDBD0 - This is the worst appliance we ever owned. Purchased in 2015, multiple problems since! 1. Soap dispenser did not dispense and leaked down the front of washer... 4 service calls, control panel finally replaced, clothes not clean, leaking continued. Had to place soap into washer drum. 2. Pedestal drawer made grating noise, track off, drawer replaced, opened better but still made irritating noise. 3. Grease oozing from side of washer both sides. Decided to look in back of washer and OMG! A copious amount of grease is also beneath & behind the washer & dryer. I had to scrape with a metal spatula device to pick up and it took over 1.5 hours to remove & clean. We are lucky a FIRE did not start when using either machine. This machine was a LEMON from the beginning. In fact when we were having it serviced, I stated I wanted it replaced but was informed 2 visits were counted as 1 and did not qualify for further investigation. We cannot rid ourselves of this machine fast enough after the last issue. New washer coming tomorrow, not a WHIRLPOOL! New machine is LG WITH 10 year warranty on motor.

I purchased this washer model WTW4950XW0 new. Within 6 months, it stopped spinning and was repaired under warranty. The spin actuator was defective. Great. A few months later, it stopped spinning, repaired under warranty and the spin actuator was bad. A few months later it stopped spinning, repaired under warranty, and the actuator was bad. Great. Another few months it stopped spinning again. This time, Whirlpool sent someone to repair it, another bad spin actuator. This time we had to pay for the part. So now that we are completely on our own, it stopped spinning yet again. Let me guess. The spin actuator is bad!!! Incredible. What a piece of crap. This washer was never used heavily.

I took the Sears salesmans suggestion and bought a high-end quiet dishwasher. It worked wonderfully until it sprung a major leak. Computer told me the phone # to call. It took a week for the Sears repairman to come out and $79 fee to just look at it. He said the fitting between the sump and the pump came off and flooded water over the electric motor. Electric motor is shot! Cost to repair is over $400 and a 3-week wait!!! When and if a new motor is installed, only then do we know if the computer is also fried. This was a high-end dishwasher. Factory warranty just ran out. Repairman said this is a common problem with this model. DO NOT BUY THIS MODEL.

Purchased double range ovens. Enamel is flaking off within 2 years. Whirlpool denies defect. They wont replace it. Any other folks with similar problems? What can I do to have it replaced? I remember the old ovens and how the enamel just stayed and stayed and stayed. Never a rust or flaking issue in those old time models. Any expertise on how the enameling process may be compromised in the newer manufacturing process (cutting corners or costs). Any options for a class action here if a commonly experienced occurrence? If similar experience drops comments/review below as a one liner - just state enamel defect. That way can figure out the number of folks with issues. Id like to take action if given the opportunity, and more so if this is a common occurrence. Lawyers are costly for one-off complaints, but there is power in numbers (think United Airlines).

My husband purchases Whirlpool washer years ago. Started acting up after 18 months. Wont spin, stays locked, clothes are soaking wet. Used troubleshooting website. Spent over $200.00 in repairs... including new board. Still doesnt work properly. Whirlpool customer service recommended buying a extended contract for over $300.00. I could have bought a $900.00 Maytag by now. Total disgusted with machine and customer service. Will never buy Whirlpool again and have told everyone by word of mouth and on facebook about this situation. DO NOT BUY WHIRLPOOL!

My dog is afraid to be anywhere near my Whirlpool side by side fridge. It makes horrible noises every 15 minutes to half an hour. I have to coax her to even let me escort her past. It has been snap crackling pop for several weeks and is getting louder with thumps and clangs. It does sound like the devil inside. Appears to be coming from the freezer side.I do not have the ice maker hooked up . It is plumbed for an ice maker but the servicemen who delivered it advised me they didnt do that . I didnt have the money to hire a plumber. The fridge was a PG& Energy Partners project in which those of certain age and income levels were presented new energy savers in exchange for old ones.Wish Id have kept the old one, especially after reading comments here. A senior, I live by myself in a fairly isolated area. I wonder now if the noise means a fire or electrical problem is imminent. My model number: ED2KVE*V*O, ED2FHE*V*O*

I purchased Whirlpool dishwasher, model DU930PWSTO, in 9/2007. It quit working in 5/2012. I expected an appliance made by a reputable manufacturer (Whirlpool) to last longer than five years. It seems like a manufacturing racket where they build these things only to be replaced a short time later. With service calls and parts replacement, its cheaper to buy a new unit. Talk about a circle jerk! And who the heck puts anything else but SS screws in a water soaked appliance? Duh. Rust! Im disgusted and dissatisfied with the whole company. Im still waiting on their response to my complaint email; at the time, the machine quit working. Whatever happened to pride in American made products? Or, did this get company bail and were now slaves to the Chinese junk once again? Ill never buy another Whirlpool appliance again. Does anyone have anything good to say about this company? I wish I would have read this blog before purchase.

I bought a 6 year warrantied Whirlpool hot water heater Model N50T61-403, product number 0733318, at Lowes Home Improvement Center and for three years the pilot light fails to stay lit. I have talked with Whirlpool 1-877-817-6750, the number on the unit, many times. I went through the troubleshooting checklist and verified all requirements. I paid a plumber $150 to check it out and he said I needed a larger supply line and venting the closet door would help. I did this and pilot still goes out periodically. Whirlpool sent me a new gas valve and it cost me another $150 to have it installed. The plumber said everything is good. But the pilot is still going out. Called Whirlpool again and talked with them for 24 minutes. The woman on the line was telling me I needed a certain amount of oxygen for this 40,000 BTU model. She was giving me minimum requirements for square or cubic feet of house with 8 inch ceilings. Yes, she said 8 inch ceilings 4 or 5 times as we went over the requirements. I got so frustrated asking her what she was talking about and she hung up on me. I called back and asked for a supervisor and a different woman had me hold on, came back and said a supervisor would call me. I did get a call back and the supervisor wanted to send me another gas valve and a burner assembly. I told him the burner assembly is working fine and I have a new gas valve. I asked him to send me a $150 along with it to pay the plumber. He said they only warranty the parts. So, am I supposed to have $450 in labor plus my time in this product on top of the original cost? I said no thank you and asked him if he would accept this as a solution if he were the customer and he said this is not a personal discussion. I know his answer. I am never buying a Whirlpool product again. But now I need to buy a new, good brand, water heater to replace the Whirlpool piece of junk. Bad product, bad company, bad warranty. I got screwed by Whirlpool once but never again.

Hot water heater model #0833T402747 purchased late 2008 - Several service calls had to be made to a plumber, due to this unit not working. The door assembly was shipped to me by Whirlpool. I had to pay again for the plumber to install this part. Hes been here 3-4 times since I bought the unit. Last Wednesday, May 2, 2012, no hot water again. The same plumber came out and said the door assembly had again gone bad. Whirlpool was contacted on Thursday morning and would not agree to do anything. They were given my plumbers name and number and I never heard back from them. I contacted Lowes in Acworth, GA and they agreed to replace the hot water heater. So now Im forced to pay for another install. I requested that Whirlpool pay this expense, and their representative, **, said no. I intend to sue them for all monies spent on this lemon and due to this lemon, I will never buy another Whirlpool product of any kind. I have told family and friends and theyve agreed that due to the bad product and worse customer service, they will also stay away from purchasing anything made by this company. Whirlpool certainly wont be hurt by me and me alone. But Ill make sure that anyone I run into at Lowes or anywhere else is even looking at a Whirlpool product will get an earful from me. This is the type of customer service that consumers dont have to put up with anymore. There are many resources on the internet to get the word out and I intend to spend a great deal of my time doing just that.

Bought Whirlpool 30 gal propane water heater in Feb, it lasted until May before the unit died. Paid for the extended plan warranty (NEVER do that!). Called support and they said they could send someone out in a little over a week (week with no hot water). The week goes by and on the day it was suppose to be repaired the guy calls and says his van broke down (this was a Friday, getting that early weekend). The earliest they can reschedule is in another week (over 2 weeks no hot water). Called Lowes to see if I can just return it (extended plan and all), no, you need a return code from the whirlpool customer support. Call the Whirlpool number again to ask for a return code, no, it is a repairable problem (even though no one will come repair it). Lesson learned, will never buy Whirlpool or anything over $50 from Lowes again.

The unit had all the features that we wanted and considered essential. The unit only weak issues is temperature(s) in both sections. The freezer is very poor with ice build up on the food stored for more than a couple of days. The manufacturer has been very weak in support as to how to solve this problem.

I purchased the original Whirlpool refrigerator in August of 2013. That was replaced in October of 2013 due to a factory defect that left the ice maker unusable. In April of 2014, we now have a factory defect that has resulted in the entire unit unable to keep the fridge below 70 degrees F. It has been 2 weeks since the fridge died and Whirlpool has informed me it will be another 2 weeks until a replacement fridge will be delivered. I have spoken with countless customer service reps and 2 customer service managers, as well as 1 executive from the executive office in Michigan. Several times Whirlpool has dropped the ball in this process. The original repair appointments were booked and had to be rebooked because the repair company could not accommodate the appointment times Whirlpool booked. It took over a week to get the fridge declared dead. Then another week just to process the request through tech support... After speaking with 2 customer service managers and being told it was being rushed, I spoke with an executive who said the claim had never been submitted and it would take another 24 to 48 hours to process. I spoke with the executive after the 48 hours and he said the fridge will be delivered in 2 weeks! 4 weeks without refrigeration for a second factory defect. I have explained that I have a newborn (6 weeks old when this started) and a 2 year old, and we have had up to 9 people staying in the house (to visit with the baby) over this period and that I need a fridge to keep my breast milk cold. I was told I would receive a $75 gift card and a $125 check to help with food and costs associated with the loss of our fridge... Neither have arrived. We are spending quite a bit on ice just to be able to keep food and milk cold to temp. so we dont have to spend money on eating out (too expensive for us). I am shocked by Whirlpool’s poor customer service. The first time the fridge was replaced I dealt with one person and didnt have to call the customer service line every day. I wish I had her number still.

I purchased this monster in 2012 and after six years of enduring not enough water to actually wash the clothes for years, now the bearings have gone out making it sound like a jet engine is in my family room when it spins. After researching the bearing issue, I find it will cost $250 to $300 to have them replaced. Its also a common problem in this model even when the washer isnt at all worn out and old. That combined with the fact that my clothes dont smell clean and some blankets come out not even wet at all, Im done. I wont ever buy a water efficient washer again. Churning the dirty underwear around with a few cups of water isnt acceptable. NOTE: The bearings left months after the extended warranty expired. Just like clockwork. I purchased a much cheaper - center agitator - washer with a deep water option available. It was half the price of this top of the line Whirlpool Cabrio Washer.

Mine came new with the home I purchased 3 years ago and so far I have had no problems at all. The only drawback is that if it is on, you can hardly tell it is running so if you forget you might interrupt the wash cycle unintentionally. It does an excellent job on dishes and the stainless steel front is easy to keep clean since there are no mechanical knobs or switches, you can just wipe it down and be done in less than a minute.

Water heater model N40t61-343 - Why does a water heater fail after 4 years when there is a warranty for 6 years? Is this water heater an omen for Whirlpool? I have a wife who is terminal and I trusted the Whirlpool name for hot water. What are Whirlpool going to do about this water heater?

Mtf18 defective refrigerator - The unit is 2 yrs old and about 6 months prior to 2014 I could not keep ice in the refrigerators ice (freezer) and the appliance compressor ran 24 hrs. a day without recycling or stop. I did not purchase an extended warranty, after all, Maytag the dependable company. The lonely Maytag repairman. Right!! The unit cost $$700. and is now an anchor. You cannot repair the compressor, only replace it...

I purchased a Whirlpool 3-door refrigerator with the freezer on the bottom on 8/17/12. Within 4 days, the ice maker stopped working. It took two days for the repairman to come out and fix it. So all is well with that. Less than 2 weeks later, the refrigerator isnt cooling. Several days later, the repairman came and determined it was the evaporator fan motor and clutch. The parts were back-ordered for 10 days. Parts came in 2 more days before he can come out and install them. He realized they sent the wrong parts. Another week went by, then he came and replaced the fan motor, which is now making an ear-piercing buzzing sound. He came back a week later and said it needed a gasket, which is back-ordered. In the meantime, he put some stick on insulation around the unit. Not much help. Another week went by, and the gasket showed up. It is still making a high-pitched whining sound. He said it was the compressor. Whatever! I hate the refrigerator. The sound is one that just grates on your nerves and you can hear it in all the rooms surrounding the kitchen! A repairman has to deem it unrepairable before they will even consider replacing it. They consider it fixed. What about my bleeding ears! I just want it gone! I am so disappointed. I thought Whirlpool was a good product with a solid reputation. I have a $2300 noise maker! Is there a class action lawsuit?!

Have owned my Whirlpool washer model# LSR 701 0PQ1 two years and had no problems with it before today... The washer was used once a week since I purchased it and only myself use it. There is only myself and my son and our loads are always small. Well today I put a load in and went to finish my other housework and when I went to check on the load, there was a weird smell in my laundry room. As I approach the washer to put softener in the rinse I saw a flash behind on the left hand side of the control panel where the size of load and water temperature selection is. I unplugged the washer and put the fire out. Have never had anything happen like this before with this brand. I already know I have to buy another washer but am scared to get another Whirlpool.

My washer worked less than a year. I finally called Whirlpool and they basically said, were a big company and you must for the rusty, broken drive shaft, pay for all new computer face plate, and service repair. I contacted the FTC and they told me they needed more complaints in order to make them do a recall on Cabrios. Good luck!

Whirlpool Duet Washing Machine model WFW9150WW02 - This machine was purchased new in Sept. 2011 along with a brand new dryer. We started noticing a rumbling sound within the first year, but both machines did a fantastic job on the laundry. Then last week, the washing machine didnt spin out a load of laundry. We called the company and they scheduled a service visit through A&E Factory Service. The technician immediately diagnosed the problem as a bad bearing and said that he had seen the problem frequently with this model and put it down to a design defect. The bearing is housed in a stainless sheath protected by a rubber seal, but the seal lets water in, which rusts the bearing. The cost to repair it was over $700. He suggested I call WP and ask for a concession, whereby the company would at least pick up all or part of the cost of parts. The service representative summarily dismissed the request, saying the company had no obligation to stand behind the product as the machine was out of warranty. I said that this was unacceptable. She was pleasant, but kept asking questions and putting me on hold. Ultimately, she said the same thing. Whirlpool was once a dependable name, no more.

My brand new oven kept turning off automatically. When reported, they kept sending a technician who kept lying to both parties regarding what the issue was. Whirlpool customer service people have been extremely rude and declined to fix the issue although my oven was under warranty without giving me proper reasoning for their actions. I am truly dumbfounded with this experience!

Whirlpool Duet - Steam cycle and sanitize on wash. Dryer is fast and automatic cycles actually work! Have had the washer 4 years and the dryer over 10. We like the Duet Washer because it had a steam cycle and a sanitize cycle plus it has a light inside that helps us see the laundry in our dark room or at night. Also we have been very happy with the cleaning - does a great job and gets the dirtiest clothes clean. The Fan Fresh feature and Delay Start are very handy especially for busy parents who may forget the laundry is in the washer.

Whirlpool Cabrio washer - Do not buy this washer. I have never placed a comment on the web before, but after reading about the same problems over and over, there should be a class action suit. The spin cycle will not balance. You have to stand over the washer and readjust the laundry. I called Whirlpool and I was told to unplug unit for 5 mins. This is a $800 washer that lasted about 2 years.

Stay away from all Whirlpool products. The appliances are terrible (broke twice for different reasons within 14 months of purchase). Customer service wait times are over 90 mins and the technicians take over 3 weeks to get to the house and they dont fix it, they order the part and that takes another 3 weeks for it to arrive and the technician comes back. We bought an extended warranty and when the fridge broke a second time, they canceled the warranty and said they had the right to cancel it as it was in the contract. Terrible, terrible company. I work in the service industry and I am in shock that this company can get away with treating customers like they have.

We bought a duet washer and dryer about 3 1/2 years ago. In that time, we had many error codes that we had to research online and fix. We have replaced many things to date. However, this last code,F70, has really been the last straw. Basically you are better off buying a new washer and staying away from Whirlpool. We had a company tech come and diagnose the washer. This code says that its the interface board. The company has replace this board 3 times and the code is still coming up. They have basically replaced everything in our washer and the code remains the same. Nothing is fixing it. They have had Whirlpool-certified employees come in to look at the washer and are unable to fix it as well. They have been trying to fix it for 2 months. I called Whirlpool corporate office and they informed me that the company that we went with is not Whirlpool-certified, therefore the only thing they will do is either give us 15 % of our money back if we were to by a new washer, or we can have a certified dealer come out and diagnose it again. Well, that is just a waste of time. We already know whats wrong with it and would have to pay again to have it diagnosed or we totally loose a lot of money. I feel that Whirlpool really should stand behind their products, considering the price tags they have on them. They should last much longer than 3 1/2 years. I will not by another Whirlpool product again. Apparently, Whirlpool doesnt seem to care about loosing customers. I dont feel that they deserve any stars but it doesnt allow to pick a negative number.

I purchased a Top load Whirlpool washing machine, replacing my old Whirlpool. I am so unhappy with this new one. I noticed that the water level are low...I had the tech here twice and they said that if here isnt any lights on the dash that the machine is working. I called the head tech, same answer. When I put the clothes in the washer I make sure that the clothes are evenly placed in the tub. The clothes comes out tangled and some not clean. Tonight I noticed that a pair of pant at the bottom of the load had white smudges/ I am so unhappy with this piece of junk/ I cant afford to buy another washer, so I am stuck with this.. I have tried all the different controls, still bad. I know the new machine are different than the old ones. I still believe that the water levels controls are not working. I have used my sister new washers and the clothes are not tangled and they are all clean.

I have a double door refrigerator with a bottom freezer. It is slightly over 2 years old and has been in use for only 7 months of that time. We just got off the phone with Whirlpool service. They will cover the cost of the control panel and defrost control. The other one I paid to replace was only one month old and it failed again. In the time between that I had to have an Icing kit put in as the Ice maker was causing ice to form inside the back wall of the refrigerator. My first call to Whirlpool was very unsatisfactory. I ended up paying for the part and the service call. The second call was about the ice-maker and they were aware of the problem and sent me a repair kit for the problem. I still had to pay for repair service. So far I have paid $561.62 for their defective parts and service calls. This time my wife called (while I was taking my frozen foods to my neighbors freezer for the second time) and went through 3 people before being told the part was still under warranty and they will send a new one. When we pushed for proper service we got it. We should never have had to go through all this. We also lost over $300.00 of frozen foods. Never buy a Whirlpool refrigerator!!!

We bought this washer on 9/05/09. Recently, it sprung a leak due to a worn out seal that the repairman said would cost more to fix than just getting another washer. You would think this might be cause for distress, but I literally jumped in the air and clicked my heels with joy! This washer has been nothing but a pain. First of all, I have to pre-soak every load before washing or the clothes come out just as dirty as they went in. I would set the timer on my stove to let me know when the 40 min soak cycle ended so I could change it to wash. Then I reset the timer for another 40 minutes. I also learned the hard way, that using any kind of heavy duty setting would turn towels into a pile of yarn. This washer cost $998, and guilt is the only reason I didnt replace it years ago. Ding Dong the washer is DEAD!!!

I just bought a Whirlpool Duet Front Loader, and it vibrates excessively and wont fully rinse out all of the detergent. I have to take the tray out each time and rinse. Also, it has a musty smell.Whirlpool sent a repairman out to replace the shocks on a washer that is less than 2 months old. The repairman told me to use less detergent, but I am only using a teaspoon of powder detergent which is recommended and using Affresh once a month. There is nothing they can do about it till it is deemed unrepairable.

This Whirlpool washing machine is over 5 years old and very reliable, I use it several times a week and have had no problems with it. Next time I will purchase a larger capacity machine so I can wash comforters and spreads easier.

Do NOT buy this washing machine. It looks nice but that is all. My elderly parents bought this washing machine based on the past experiences with Whirlpool but the quality of the product has changed. This machine constantly errors and does not allow them to wash clothes. I have followed the instructions in the manual to try and clear the errors. I ended up calling Whirlpool and the response I got was... It will be anywhere from $80 to $125 for someone to come out and look at it. This is a product which should not stop working after 2 years. I guess Whirlpool only stands by their products for a year because they think it is only built for a years worth of service. I wish I had better things to say because the previous Whirlpool machine lasted over 20 years.

We purchased a Whirlpool Cabrio Washer (Mod #WTW7300XW1) and Dryer in 2011. Ever since we have had the washer it has eaten clothing, towels, sheets etc. It now has a main bearing that is so noisy that we have to close the door to the laundry room to be able to hear in the rest of the house. Also the sealed tank around the drum is now leaking. We invested close to $1000.00 in this washer and in my opinion it is a piece of junk. The washer repairman told me that he has had 3 (three) other Cabrios with the same problem in the last month, but Whirlpool says that there is nothing they can do as they have had no issues with this problem. Last Whirlpool product that I will buy.

We bought this fridge 1 year ago. We have already been without a fridge from Oct 2016 to Jan 30, 2017 due to a drawer going bad which caused the whole thing to quit. Now it has an obstruction in the Freon lines that causes it to freeze up and not cool. It was deemed not repairable by service company sent by Whirlpool/KitchenAid, and yet they want one more test run. The last person I spoke with at customer service had a flippant attitude and said there are no notes. What they do is drag you along for so long, make you wait and abuse you with tests, and hope you finally give up and go away. I will never buy another thing with Whirlpool/KitchenAid stamped on it!

I bought a whirlpool Washer in 2011 which I bought an extended warranty. Thank Goodness! It has broken every year. At first I was ok since they always fixed it. It is very inefficient and the clothes are not clean. But today I am so ticked. It broke in Sept. and they have come out twice and cant fix it. Now they say it will be Dec. before they can fix it as part is backordered. REALLY!!! Im expected to not have a washer from Sept. to Dec. with no compensation! I have called both Whirlpool and the warranty company and they say thats just the way it is. I WILL NEVER BUY A WHIRLPOOL AGAIN. The warranty service is through Federal Warranty Service.

Warning to anyone considering this washing machine. It has actually destroyed some of my clothing by twisting and tying legs and arms of pants and shirts tightly together and giving the clothes a beating rather than a reasonably careful washing. Rubbing your clothes on a rock at the bank of some river would be preferable to using this machine. It does not provide enough water to wash clothing without abusing it. I blame myself for assuming that no company would attempt to put a product that performed like this on the market. I bought this machine at hhgregg.

We bought this Whirlpool Cabrio washer 2 years ago and have hated it since the first load. It does not clean clothes, and the so-called large capacity will barely clean 5 regular towels. And if you wash diapers, do not buy this washer. If a load is really dirty, you have to wash it 2 or 3 times for clothes to be clean. Then, there is the awful mildewy, moldy smell after a few washes. How can a washer that gets so bacteria-laden be allowed to be sold on the market. Ive been washing laundry for 45 years, and Ive never had this kind of wash-related problems. This washer is an overpriced nightmare. I cannot wait until I can save enough to replace it. And I am watching and hoping a class action suit comes out to force Whirlpool to take these washers back, refund the money spent, and apologize to all the people who purchased one.

I bought my washer duet (model WFW94HEXL2) in Sept. 2011. Today is Jan. 2013 and it has been a year and four months since I got the washer. I decided not to buy an extended warranty. Its only my husband and I at the house so we take really good care of our appliances. The washer stopped working and is giving me a code F-6/E3/E1. Basically, I need to change the central control unit ($350), door latch ($120) and labor ($180), for a total of $656.13. Really? I paid $1,105.00 for the washer. Im really upset. I called Whirlpool and they said the item is out the warranty and there is nothing they can do. I am really upset.

My gas hot water heater failed. The pilot went out and could not be relit. The Whirlpool water heater has a 12 year warranty and we are in year 5. Sears said they could not send anyone to repair it because there was no service in our area. We live 30 minutes from Dallas/Ft. Worth, Texas. They offered to replace it even though I had a plumber on standby, ready to replace it. They said they could not let me do that if they had one in stock. After waiting a week for the delivery, they called at 4:45 pm to claim that the delivery truck would not start. They would not put it on another truck or help in any way. Then they said it would be another week before they could deliver it. All this time we are going without hot water, trying to cook, clean, take baths, do laundry etc. They had no sympathy and refused to provide compensation so I could proceed with installing a new water heater. I could have done this if I knew a check was in the mail but they refused to allow me to do this. This happened to me at another big box store years ago and they sent a check immediately. The customer support in the hot water heater dept at Sears was terrible. If they cant send someone to repair and they cant provide a replacement within a few days, it is only reasonable to offer payment so that the customer and move forward with repairs. I will never buy another appliance from Sears after this nightmare. On December 4th Im supposed to get the delayed hot water heater but if the truck doesnt start, who knows how long I will have to wait. I am reasonable and flexible but lack of hot water is something a customer should not have to wait two weeks to get resolved.

I purchased my Cabrio washer in April 2011 from Lowes. Huge mistake. The washer has broken 4 times under normal family of 5 conditions. The last time was in March 2015 - the barring was stuck on the drum failed to allow it to spin. It was stuck to the point where the unit needed to be shop repaired. It took 2 weeks to remove and replace the fail part. I just called service again today for the same noise as last time. It kills me that I spent so much $ on a product from a well-known company only to have it fail so often.

The washer has rust under the rim in the inside - also the paint is bubbling and peeling under the rim of the washer. I contacted Whirlpool and was told that is a cosmetic problem. There is no warranty for rust or peeling paint. I will never buy another Whirlpool washer. I paid over $700.00 for this washer and I dont think I should have a rust problem after 5 years.

I bought a Whirlpool refrigerator January 2016. 4 months later the refrigerator stopped working. It took over a week for Whirlpool to have it repaired. Two weeks later the refrigerator stopped working again. It took four days for Whirlpool to get a repair man to my house. I called customer service 4x asking for a replacement or loaner or possibly they could expedite the repairs. All they could do was recite my warranty to me stating that they are only responsible for repairs. I was in touch with their executive office and was pretty much told tough patooties - my warranty only covers repair. The executive office told me to wait for a third breakdown and then we could talk about an exchange. WHAT??? I have to suffer a third inconvenience before Whirlpool will do anything??? I lost hundreds of dollars in food, have to live two weeks without refrigeration in 95 degree Florida weather, had to go shopping on a daily basis or eat fast food (at my expense) because I couldnt even keep milk for breakfast cereal. I filed a claim with BBB only to have Whirlpool close the claim stating that they fixed the refrigerator.

ED5PHEXNK00 Stainless Steel side by side Refrigerator bought in 2004, look out!The refrigerator caught fire today and there was smoke everywhere. Had I not been home, damage would have been out of control. I traced the smoke to the bottom of the refrigerator. I pulled the unit out from the wall and unplugged the power to the unit. My unit is out of warranty and past the extended Lowes warranty. The repair diagnosis is $100 to start.Whirlpool has recalled its other brands (Maytag, etc.) for this same problem but not its Whirlpool brand. Our problem is the same problem with hundreds of other people: Whirlpool fridges burning, smoking, and being a life threatening hazard to families all over America because of the faulty relay to compressor. Whirlpool better recall this model. They need to fix this or they will have much bigger issues to deal with (corporate manslaughter from a known issue and no action or protection for its consumers). The refrigerator is a result of Whirlpool’s negligence; thus, it’s potentially deadly.

After Hurricane Katrina, six years ago, the gas water heater in my house had to be replaced due to the house getting flooded. For the past six years, the pilot light and/or igniter for the gas water heater has had to be replaced if not once a year, twice a year because it will not stay lit. Each time, Whirlpool would send a new igniter and/or pilot light part and would reimburse me the cost of labor to have the part(s) replaced.Now, after six years and exhausted of fighting with Whirlpool to stand behind their product and make it right, they are finally giving me an authorization to get a new gas water heater. However, now they are telling me they will not cover the cost of labor for replacing the entire water heater. My plumber will have to pull the defective water heater out of my house, take it to Lowes, pick up the new water heater and install it in my home. And Im supposed to accept their not paying for the labor of replacing their faulty water heater? I questioned this and told Whirlpool they paid for labor for the parts to be replaced for the past six years. Whirlpool then said they would pay up to $100. This is not acceptable. I was reimbursed more than $100 for the labor to replace a part that fits in a shoe box. (Multiply $100+ times 6. They paid more than $600 over the past six years.) The cost to replace an entire water heater, picking it up from the store included, will cost more than $200, if not $300! I would not have to pay anything if the Whirlpool product was not defective!I told the manager I was speaking with at Whirlpool I wanted to speak with his boss or someone who had more authority than he did. He refused. I asked him, Was he telling me no I could not speak with someone above him? He finally said he would have someone call me.I believe I should be reimbursed for the entire amount of labor to replace the water heater since the water heater is a defective product and I have to have it replaced not by my choice but out of necessity and safety. If it is defective in one area, who is to say in trying to light the pilot light, one day it will not do something worse than just not light up. What if it decides to explode? Defective is defective and I feel my family is in danger from a defective product and it should be replaced at the cost of Whirlpool not mine.

I purchased a home from Pulte and closed in June of 2020 and had no choice but to take Whirlpool appliances. Pulte does not offer high end appliances in order to maximize their profit. The first thing that failed after only 3 months was the Microwave and because we didnt want to get the same cheap microwave we upgraded and paid 400 for a Kitchen Aid, same size but never received the trim kit that matches the oven that came in sometime in October 2020. It is now January 2022 and we are still waiting for the trim kit. Every time we call to find out we spend hours on the phone.The refrigerator is a cheap version of the worst refrigerator made in China, the ice maker works ok but ice gets stuck in the chute and when it doesnt get stuck half goes to the glass and the other half to the floor. Poor design and we are stuck with it. Tried to buy an LG from Costco but it wont go through the door so again we are stuck with this small refrigerator with no room for groceries for two people. Stovetop is also cheap, only looks good the day we got the house, one of the burners would go off when turned to low with gas still flowing. Grates look 10 years old but must admit we cook every day. Oven will not calibrate and it is not accurate so we have learned to set everything 10 degrees higher to make up for the variance. Dishwasher had issues as well, unless you run it for 3 hours the shorter settings always have dishes or utensils still soiled. Warranties have expired after one year so it is now time to replace almost everything if we want decent appliances. Very disappointed but I blame Pulte for buying cheap.

The 12 year warranty, means nothing. The heater only worked for 30 months, and then its upper sensor fault code flashes, and the heater shut down. I called Whirlpool, and they have me use an ohm meter to help troubleshoot the problem. So if you are not handy, you are out of luck. They decided it was my control unit that is defective. They will send me the part free, but I have to pay shipping and installation. What a deal, and what kind of management would dream up of this. The heater is marketed as a 12 year warranty model (only on the tank). Would anyone, having been through this, buy another Whirlpool product?

We have a Whirlpool washer wtw5640xw2, we have been experiencing burning wire smells for some time. We had bought the extended warranty. Lowes sent out a repair company. They replaced the main board and the problem has continued. This has been as intermittent problem with the burning smell. We experienced it this week really bad! I thought the machine was on fire. We called the repair company and they said they had fixed the problem. My husband called the Whirpool number and they said they would NOT do anything to help us. We are trying to get help from Lowes where we bought the washer. I am terribly afraid to use the machine. This model needs to be discontinued.. We bought this machine 5-07-12. If we dont get some help, we are going to our lawyer.

I hate my Whirlpool refrigerator: It has a upper freezer with no light. The shelves are not split and raising or lowering shelves gains nothing and may even take space away. I would never ever buy another Whirlpool.

I have owned this Whirlpool Refrigerator French Door MODEL WRF990SLAM01 for less than 10 months. The ice machine broke down completely a few weeks ago. We called Whirlpool and they sent a repairman out the following week. He left saying he had to order parts. About 8 days later, they called to let me know they have the part in and scheduled a time to fix it. They put the new part on and said ice should be coming out in the next 72 hours. It never happened!! Not only did the ice maker stop working, the freezer stopped working which was about $300 worth of frozen meat/goods down the drain. I called the appliance repair guy. He said, I was worried about that, this product is known to have these issues. I asked, Does Whirlpool know? He replied, Absolutely, they have a kit to fix this but its not 100% guaranteed to fix this issue. REALLY?!!! I called Whirlpool and they could have cared less. There were no apologies, no type of compensation (exchange/replace). It is now going on day 22 and we still have no ice or freezer. This fridge cost me $2500 and four requested days off so I could wait for the repairman. Whirlpool, you as a company should be ashamed and outraged. You are more concerned about the bottom line of recalling these lemons and forgetting the impact you are having on us consumers. How many people are going through this issue that will not under any circumstance purchase a Whirlpool product again? I am so happy I am not investing in this company as this will impact this company in the future. They may be selling quite a few now to new homes/builders but when the word gets out what type of product they are selling and not repairing prior to the sale and knowingly letting people buy these, it leaves quite a bit of culpability on their hands. IF you are going to sell crap product, then stand behind it and repair/replace it prior to selling it to retailers!! You are a pathetic company!! STAY AWAY FROM WHIRLPOOL PRODUCTS!!!

Such an expensive refrigerator but poor quality. Bought at Home Depot back in November of 2019. The bottom Freezer freezes up messing up everything only three months after purchase. I wouldn’t recommend it at all to anyone.

1 year ago I purchased the top of the line large capacity tub cabrio washer and dryer. I dont understand why they sell a large capacity when you dont get enough water to get a handful of stuff clean. If they offered a trade in allowance for a standard agitator washer I would be first in line. Clothes dont look clean at all. Save your money folks not worth it.

A new washer, kept in pristine condition, indoors in an upstairs laundry room, used by 1 person for 4 years should NOT rust out. I took pictures and sent them to Julia ** a company representative after she offered me a discount on a new washer but would not send me an email with directions like it was some kind of secret until I insisted several times. The email simply had her phone number. I was to let her know the models I would be interested in and she would tell me if those were available for the discount. Then the company would charge me, deliver the new one and charge me to install and remove the old one. How is this for a great company. I sent her the models I might consider. No word back. Whirlpool, not looking like a stand-up company to be proud of. Shame on this company.I like the machine, but seeing it rust out before my very eyes has changed my mind. How will they address a 4 year old washer rusting from the inside out? How will they address a 1 year warranty? I found a copy of Whirlpool Washer Warranty that used to have up to five years for issues such as poor workmanship. It takes more than a year to find these things out. Dont make them if you cant guarantee that they will last. My last Maytag lasted 18 years and was still in good shape. I just wanted a model without the agitator in the middle and on that would conserve water. Should have kept the old one.

We bought a side by side refrigerator/freezer in 2013 from our local Best Buy. We have usually bought Whirlpool appliances. Before we bought this refrigerator the last Whirlpool we had for 25 years. This past week our refrigerator went out. We called a repair man. He said the circuit board was out and would cost $450.00 to replace it. We decided to buy a new one. I am very disappointed that it only lasted 7 years. Oh I forgot to mention the ice maker went out about a year ago. We did get new filters as instructed. We did not buy another Whirlpool.

Bought a Whirlpool French door refrigerator in March 2014 and have had to have it serviced 4 times now - all for the same issue. We get frost in the refrigerator (not the freezer, the refrigerator). The same parts keep being replaced but they are all defective. This last time the service tech said he contacted Whirlpool and they had a redesigned part that should take care of it. Within 3 days of the new part being installed the frost is back. The other issue is the loud noise of the compressor. We have had multiple Whirlpool products through the years, but this is the last.

My new fridge is leaking large amounts of water on the floor, but it is not from the ice maker, as it is not hooked up. I have a Whirlpool refrigerator, model number GB2FHDXWS04, purchased in August of 2010. It was with good faith that I chose what I thought was a high-quality product, as well as, it was chosen because it was made in the USA and would be supporting US families, not China.Within one year, just as soon as the one-year warranty expired it began leaking water daily, all over my wooden kitchen floor, causing the floor boards to begin buckling. It is not from the ice maker, as it is not hooked up. Not only is my floor being ruined, but my one-year old refrigerator is not working up to standards, for which I chose the Whirlpool brand. My refrigerator has been maintained and operated by all instructions provided for this product.I assume that this company no longer wants to be in good standing with its customers, and refuses to make good on a major problem, for which a large amount of money was spent on a high quality serviceable item, by paying for the repair or replacement of obviously defective parts, or by the replacement of the entire refrigerator.

This machine, like all other water sensor machines, will not let you wash a few items that are lightweight without filling the whole machine up almost all the way. The reason being is that if the items are light, they will float in the water above the water level and the sensor thinks it needs to put more water in and even with putting something in to weigh it down like a wet towel doesnt always work, nor should you have to do this. You will waste more water in the long run if you only have a few items to wash, ie baby clothes, underwear, rags, etc. I am so disappointed that I had no other choice but to get this machine.

I bought a heater from Lowes in south lebanon ohio in feb. 2013. Gas valve is bad. Whirlpool will not replace it because it was put in a utility room with a toilet in. What a bunch of crap. Their service dept. is joke.

Needed a washer right away and have had Whirlpool before. Simple & easy to use. Not confusing to the average person or teenager for that matter. Reliability from Whirlpool is excellent. I have had many products from them and have enjoyed them all. They have been quite reliable over the last 9 years. They are out of date but they work. Not a lot of bells and whistles but still nice. They are both full size and have enough options for me. I am still happy with the pair and would purchase again if needed in the future. Price was good at the time as I cannot see spending $1K on them. Not always the more expensive is a good idea either.

I have a kitchen collection of Whirlpool products, not even 2 1/2 years old. I have had nothing but issues. Microwave was completely rebuilt within few months, refrigerator and freezer multiple issues. Latest is the freezer stopped working, now my good is ruined!!! Wont always make ice in the icemaker. Already had to replace freezer door because it was warped and the seal didnt work and now my dishwasher isnt working!!! **!!! I waited 20 years for a new kitchen, finally got one and did extensive research thinking I was safe with whirlpool. I was wrong. So now what, what happens when the warranty runs out, Im screwed. Shame on you whirlpool for putting out crappy products and doing NOTHING to try and fix this!!

Whirlpool Cabrio Washer WTW7340XW sounds like a small jet during spin cycle. The Whirlpool Cabrio Washers have a very well known and well documented problem with the tub bearings failing. Many many disgruntled owners have posted their complaints online, and there are many videos showing the issue on youtube. This issue is so prevalent that the manufacturer has created a tub bearing failure repair kit for $350. The repair is so expensive and labor intensive that many of the certified Whirlpool repair shops no longer work on the Cabrio washer stating that a better washer can be purchased for the cost of this repair.That said, the manufacturers customer service group denies that the Cabrio tub bearing failures is a common problem and are quick to state that Whirlpool holds no liability for this problem. Ramping the complaint up to a customer service supervisor is met with the same canned response. Regardless of the thousands of complaints Whirlpool is claiming that it is normal wear and tear for the tub bearings to fail. The manufacturer should recall the units for this manufacturing defect in the Cabrio design.

Spent the extra money to have a beautiful, slide-in oven. The AquaLift technology just seemed like another plus. After the turkey cooked, just seemed like another oven to clean. The AQUALIFT does not work, except for the bottom of the oven!! A fresh oven cleaner? Only available only. Get this beautiful range, not AQUALIFT TECHNOLOGY. CLEANING with it.

We bought a new Whirlpool dishwasher with a kitchen reno. It cost over $1000. One month out of warranty the pump died. As this is apparently a common thing with these dishwashers the company sent a new pump, free of charge, but we still had to pay $150 for the install. Now, less than 2 years after purchase, the dishwasher refuses to drain. I wrote to the company, they are not interested. Dont buy Whirlpool, you are only throwing money away.

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

Bought the model before this just over 2 years. Conveniently it broke just after the warranty expired. I chose not to buy a extended warranty as my last fridge from KitchenAid is over 20 years old and never had a single problem with and still operates like NEW. I can’t say that for my Whirlpool which was very expensive. It has been with an issue within the ice maker for over 8 months. Every computer board has been replaced twice with no fix. Then tried to replace the cooling fan within the ice maker unit seven times. Whirlpool could not find the right part, as the wiring had changed mid model and have no record of when it was changed and what models affected.Certified Whirlpool technician was great and so apologetic. I had taken 7 Mondays off to meet him to only have the wrong part time and time again. Whirlpool support tech line basically said he was wrong, yet I witnessed all visits and my 3 plug fan unit did not match Whirlpools newer part that was 2 plugs. I was not happy missing so much work because Whirlpool is incompetent. Finally my tech ordered a whole new ice maker, including the cooling fan. Lo and behold, Eighth time, parts did not match. He again called Whirlpool tech support and reordered another set one final time. Another Monday to find that this time the parts did fit, but cooling fan still did not work. He called Whirlpool tech support again. They started to trace wires one by one.Whirlpool tech support said it was a bad or broken wire somewhere in the cavity of the fridge buried in insulation and was not replaceable. In other words I have a $3000+ refrigerator that is useless. Whirlpool said they would replace the unit. But when I called, they said since I didnt have an extended warranty, they would prorate it and it’s going to cost me over $1000 of my money to to replace due to a manufacturer wiring defect after only 2 years. What the Heck, I was willing to pay to fix it, but Whirlpool can’t fix it. Don’t buy a Whirlpool product as they are Junk and do not stand behind their BRAND!!! No matter who I talked to, they kept falling back to their word track of it’s my fault I didn’t get an expensive extended warranty, yet they can’t fix a wire they installed incorrectly.Wires don’t just break after 2 years. You get longer warranties for cars for the Love of God. I asked them to just send me the money they were willing to put towards a new Whirlpool fridge, so I could buy a Real Brand that stands behind their products like KitchenAid. Of course the answer was NO. Buyer Beware, don’t buy a Whirlpool anything. Did I mention my Whirlpool certified technician was having a Whirlpool dishwasher issue that Whirlpool can’t fix and that’s his profession. Same type of response. Don’t Buy Whirlpool Products, they are Junk and you will get No support from Whirlpool!!!

I do like my Whirlpool refrigerator, but it started to not cool things anymore. I had to get it fixed. The professional I had come out to fix it said that these particular Whirlpool models didnt have a specific part they they needed. It also got built up with ice that needed to be broken down. Overall, I wouldnt buy this model again, but that doesnt mean that all Whirlpool refrigerators are bad. Just this particular model.

Whirlpool Cabrio drain problem - I never had a washing machine that lets so much through to the drain pump. I replaced pump three times already. First of all, if you put anything with buttons in this machine, you can kiss it goodbye. This machine destroys clothes then lets buttons and coins and whatever through to destroy the fins on the discharge pump. When is the BBB going to do something about this consumer ripoff?

The capacity is small but it does a good job of washing and drying the dishes. I always check to make sure that all dishes are washed including silverware and they are. My dishwasher is quite old but it is still sufficient for our use.

Our new fridge, which was already an exchange from another unit that went bad, kept freezing things in fridge compartment. A tech was sent out three times and then the compartment quit working completely. They stated they would replace for us, only way they would replace was to have them ship a new unit which would take two weeks. So we are without a refrigerator for two weeks. Asked if I could go buy one and be reimbursed. I could but I would NOT be reimbursed for full amount. The company reps I spoke to could have cared less about our situation especially Fred who supposedly is a supervisor. Do yourself a favor...DON’T buy Whirlpool. Their customer service sucks!!!

I purchased the Cabrio washer and dryer and paid for the extended warranty from Lowes about 5 years ago. After about a year, the washer had problems with excessive vibration and noise. Under Lowes warranty, a repairman came and adjusted the level. He came out several more times and made other adjustments, replaced the drum, then bearings and raised the level again. He said he could not declare the washer a lemon, even though it was because they were told this was taboo. They were instructed to do whatever they could to keep the washer going throughout the life of the warranty. Now the washer stops mid-cycle and an fl or f1 error code appears on the control board. I contacted Customer Service who said I can purchase another extended warranty for over $300 or pay their repairman for the visit including parts and labor. What I paid for the extended warranty and to purchase a new one would pay for a new washer.

Purchased Whirlpool gas hot water heater from LOWES on 9/25/2016. After the installation, tried to light the pilot light for 90 minutes. Followed the recommended instructions, I could not get it to light. Called LOWES they told me to call Whirlpool. I did so, and told them I will return the heater to LOWES the next day. Whirlpool customer service very bad. Returned the heater to LOWES the next morning, went to a local plumbing shop and purchased a Rheem heater. After installation it lit very first attempt. Now three weeks later I get a letter in mail from collection agency that LOWES turned me in for stopping payment on the check I wrote them. After reading the many negative reviews and they disregard for my and my familys safety, nobody should purchase a Whirlpool gas heater from LOWES.

We purchased the Whirlpool Cabrio washer and dryer duet exclusive to Lowe’s in June 2011. I was immediately dissatisfied and went to Lowe’s. They told me I only had 7 days to return it. They dispatched a service man and he said it was working as it was intended to but I would never be satisfied. If I had dirty clothes from farming, construction, or mining, I should forget about it.” The washer is an eco-friendly model and all the clothes do not get wet. It wrings them out very tight and everything needs to be dried or ironed to get rid of the wrinkles. After 6 visits and lots of stress, I am returning the washer to Lowe’s and they will replace it with a different model. It definitely will not be a Whirlpool. I am very disappointed in the service and response I received from Lowes.

Never again will I purchase any Whirlpool product. I was seduced into purchasing a Whirlpool dehumidifier by the sale price at Canadian Tire. Big mistake! It worked as expected for four months before all the refrigerant leaked out - we found this out later. I contacted Whirlpool and was told I could take it to their authorized service depot (a 50 minute drive from here) for repairs. I did so and was charged $44.80 for them to troubleshoot the unit. Two weeks later they told me that the refrigerant had leaked out and it would cost $563 for repairs. For a $200 unit!! Get serious! I pointed out, according to my Canadian Tire receipt that the warranty was for 5 years on the compressor and sealed components. After further collaboration between the repair depot and Whirlpool, I was told that my warranty is not with Whirlpool but rather with the company that produced the unit for Whirlpool, namely Hisense and that the Whirlpool repair depot did not do warranty work for Hisense. I then had to fax the technician report to Hisense to get an authorization number for a replacement unit from Canadian Tire. Once armed with the authorization number, I had to visit my local Canadian Tire store and pick up the replacement. That unit worked well for about nine months before it failed. Considering service depot charges and all the driving involved, it cost me something like $100 for a warranty replacement (not including my time). No more fooling around with this junk. I just ordered a Kenmore dehumidifier. Hope that one is a better investment. I see now that Canadian Tire no longer sells these units. Maybe they figured it out. Judging from other Whirlpool reviews, it seems I am not alone in my views. My recommendation - stay away from Whirlpool!

Whirlpool is the manufacturer of most appliances including the Kenmore dishwasher. Your products are made horribly for the mother board to go out in 2 years is ridiculous. I purchased a stainless steel dishwasher from Sears in August of 2014. 2 weeks ago I received error codes E2 and F2. A technician came out and the mother board needs replaced because water got into it... its a dishwasher. The cost to fix $465. I paid $673. The sales person informed me that I should have purchased the extended warranty because the appliances now only last a few years. Seriously... fleecing of America. This is my last purchase from Sears. We have bought appliances for 30 years from Sears and this is the end. They could care less about customer service or their products. Apparently everything is now made by Whirlpool who will also be getting a review. Shame on you for making poor products.

First Id like to start by saying anyone whom owns Whirlpool make sure to purchase every extra Warranty you can get your hands on right away. Two years ago my husband and I purchased the whole Whirlpool Appliance Kitchen Collection. The gas oven range has been my only real issue. Within a few months my oven wouldnt light. Its a good thing I noticed because there are no safety features that turn the gas off if it doesnt fire up and the gas builds up so so fast its scary. Our Warranty covered the broken igniter switch only for it to act up for over a year. We had to try several times before the oven would light until it just didnt again and it was repaired again under Warranty. Aqua Lift Technology is just something they made up to get us all to purchase it. I swear on my life it doesnt even work a tiny bit. Now, the bottom of my $800 oven is chipping away. I have not worked this out with them yet and I will repost to let others know how it works out. Liquid also gets in between glass oven door, cant ever clean it. Good luck.

July 2017 I purchased a Whirlpool refrigerator Model # WRF757SDEM00 S/NK51709722. The refrigerator portion went out, the repairman said it was the fan therefore I spent 351.00 dollars for house call and fan. When that did not work the repairman spoke to whirlpool and they said the panel of small computer may go out with it 212.00 plus tax. Did not allow that and tried another repairman who said the value that switches from freezer to refrigerator was out and if I could find someone to fix it would cost between 600 and 800. I went out and bought a Samsung because on the front said 10 year warranty. At least anything is better than 1 year whirlpool offers. There is NOTHING in the name.

Whirlpool Auto Load Sensing - I bought the washer in Aug 2010 and it worked well until the timer went out this year. Its only 4 years old! The repairman said it would cost $350 to fix - the machine cost me $469 to begin with! Whirlpool builds a poor quality product and Id advise people not to buy their brand of anything.

I bought a Cabrio set in June 2007. Within two years, I had to have the barrings replaced ($800 job). Now, its two years later and Im getting a F50 code. The repairman put in a new part, still got the same code and left. I am out $970. I am a disabled vet/single parent and now I have to buy a new washer. Who is going to start the class action suit against Whirlpool?

Without a doubt, the worst washing machine Ive ever owned. After 15 years, my trusty old Maytag finally quit, so we searched around and ended up purchasing the Whirlpool Cabrio Platinum 3 years ago. In that time, the hinge on the lid broke, and now it makes a deafening noise when spinning. We called a repairman and he said the bearings were bad and needed to be replaced... Total cost $275 plus $50 for fixing the lid. When we told the repairman that it was only 3 years old he couldnt believe it! We decided against fixing it because from the start it never got the clothes as clean as we were used to, and without the agitator post in the middle, which was a big selling point by the salesperson who sold it to us, the washer continually stops with an Uneven Load message. Large load, small load, it doesnt matter. You cant do a load of any size without the load becoming uneven. We are now searching for a new washer, and although I dont know what well buy, I can guarantee it wont be a Whirlpool.

When we remodeled our kitchen after checking a lot of brands of oven we decided to buy the Whirlpool Self Cleaning stove/oven. Loved the look of it. When trying to clean the oven I followed the directions just as its said in the manual. After the cleaning was complete it didnt even look like it clean the oven. I called customer service and they told me I had to clean the oven with a little elbow grease before I put the self cleaning on? Really? I have to clean the self cleaning oven by hand beforehand? Why did I purchase a self cleaning oven then? And because it was just 2 weeks out of warranty they would not help at the 800 number. NEVER NEVER again will I ever purchase Whirlpool! How they treat their customers is disgusting!

I am posting to help anyone else avoid the purchase of this machine! The lid has cracked and now warped into a position where it wont stay down. Obviously a washer will not work without being in the locked position, so we have to put several heavy things on top of it just to run a load of laundry. This is not what we expect out of a washer that we paid $900 for only two years ago!!!! We contacted Whirlpool and they offered to fix it for $350. REALLY??? I SHOULD NOT have to pour money into a washer this expensive after two years!!!! I am so disappointed in Whirlpool, this was the entire reason we purchased Whirlpool products, to avoid stress of broken appliances. We wanted reliability for our busy family and instead we bought into more stress.

I bought this top loading, low water machine 1.5 years ago, $500.00, did not buy extended warranty, expect major appliance to last at least 5 years. Motherboard is out, will not spin, will cost at least 200 to $300 to get it fixed! Selling on Craigslist for 50. So sad. Will never buy whirlpool again, waste of hard earned money!

The dishwasher is quiet and seems to clean most all of the dishes even when there is dried on food remnants. Multiple cycles that allow for light, medium and heavy cleaning. Also the ability for air dry and minimum use of water. The size is appropriate for normal amount of dishes, pots, pans, etc. Stainless steel front with most of the controls hidden. I have always had good luck with Whirlpool products, with this dishwasher continuing with being a quality product for the amount of money spent.

I had purchased a washing machine trough CSD canteen and go for AMC for five years on September 25, 2006. In September 2010, I lodged a complaint and the Engineer visited and asked for a replacement of the bottom cover. I said okay, but later on he told me that I have to replace the complete outer cover. I agreed and asked them to replace it. The cost is fixed for 2,500Rs. They replaced the cover but did not replace the bottom cover.I talked to the agency and they agreed to hold to 1,000Rs for the bottom cover and I paid to them 1,500Rs. Later they brought an old cover and I refused to replace that. They told that the bottom cover is not available. Then they never tried to replace the bottom cover. I arranged for the same from the local marketing for 600Rs and replaced it. I paid the service charge for the engineer.Later, I lodged a complaint that the machine was not drying the cloth. The engineer visited and told me that the belt will be replaced on payment. I agreed and he told me that I will visit the next day and replaced the belt. But he did not come until it was late.On September 18, 2011, with number DL0911018283, my machine was not switching on and I lodged a complaint to customer care. But no engineer visited me. Then I regularly complained but there was no response from the agency. On September 23, I talked to customer care, Mr. **, that I am going out of station and I lodged a complaint from the last five days that no engineer visited me. My AMC is expiring on September 25, 2011. I will come back on October and then send the engineer. On October 9, I reminded them that they refresh my complaint with number DL1011007031. The engineer visited and told me that the PCB of the machine is faulty and I have to pay 3,500Rs.I told him that I complained for this problem during the AMC period, hence they are supposed to repair my machine free of cost but he refused. I talked to customer care and tried to resolve the issue but I was not successful. Then I talked to Mr. **, the head of Customer care in Delhi, on October 12. He promised to resolve the issue but no engineer visited me and my machine is still defective. On October 13, I tried to contact Mr. ** several times but he or his PA is not picking up the phone. Now, how will I get to repair my machine?

I am writing to you all today to urge you to not purchase Whirlpool products specifically Whirlpool 2-cu ft High-Efficiency Front-Load Washer. I purchased a front loader washing machine for our tenants through Sears back in June of 2013. When it was hooked up it had an error code on it so we contacted Sears and 3 weeks later they sent out a repairman telling us it needed a new motor (this machine had not even washed 1 load of laundry). They ordered the part and Sears paid 1200 to replace a part on an 800.00 washer.....yeah I know dumb right. Well the part replacement did not work. (Surprised) They ordered and delivered a new washer 1 month later....same error code. Lets try again with another washer......same error code. How about another one......water would not stop running into the machine because the sensor was broken. Wait we are not done how about another one.....same error code. No I am not kidding, 10 months later 5 washing machines and my tenants have yet to have been able to wash a single load of laundry. I have been reimbursing my tenants every month for not having a washer for the past 10 months. I finally had Sears reimburse for the washer which they will pick up soon. I am out all the interest for the past 10 months for a product never used. To top it all off I called Whirlpool directly to see if they would be willing to at least give me a coupon for any amount toward the purchase of a different washer. They told me quote We dont do anything to compensate our customer for their troubles. That is the icing on the cake folks!!! I will never purchase another Whirlpool product and I encourage you all to not as well. I want to show them how not caring for their customers can impact them. Please share if you can, but more importantly please pass the word!!!!!

Do not buy Whirlpool appliances! Save yourself the trouble. I have a Whirlpool free-standing gas range that I bought when I purchased my house in June 2008. Just the other day, the oven stopped working. When I went to turn the oven on, I can hear a clicking sound but the burners in the oven do not ignite. I called Whirlpool and they offered to send someone out to fix the problem. By the time someone comes out and charges me for parts, labor, etc, I will probably have paid half of what I paid for the range when it was new! I also had the same thing happen with a Frigidaire refrigerator last year! The bottom line is that brand name appliances are not built the way they used to be. I am actually looking at buying a Samsung or some other model and try my chances with them!

I purchased a Whirlpool microwave model #WHM3205XVS1 on October 2, 2011. The handle broke off in little pieces and was repaired in March 2012. Handle broke off again in little pieces in September 2012. This will be the 3rd handle that will continue to break in little pieces every 6 months. According to both repair men that were here, this is their comment: No customer abuse, this is a very common problem with this model. After to speaking to 3 people at Whirlpool, I was told by everyone, This is cosmetic problem and we will not fix after the 1 year manufacturers warranty is up. I started with the the first person, went to her supervisor, then went to her supervisor. I am now waiting for a call from a manager although I was told I will continue to get the same answer no matter how far up the chain of command I go. So, I was told that it is okay to have 2 screws sticking out holding the remaining part of the handle that is left, because it is a cosmetic, not a functional problem. I will never stop with Whirlpool. I will call 4 times a day if necessary. I will never purchase another Whirlpool product again! I will tell everyone I know not to purchase one of their products. Be careful. They manufacture products for many other companies, i.e., Sears, Amana, Jenn-Air, and many, many more.

Whirlpool Cabrio - good consumer rating. Ive had it for 2 years. It does not clean well and the clothes does not smell clean even though I often clean the washer and leave the top open when Im not using it. Ive also had it service 3 times because the rotator keeps going off and makes a lot of noise. I bought an LG dishwasher for $1300 and it lasted 7 months and completely broke down less than a year and had to be replaced. After I bought a $400 Whirlpool. It does the same job and Ive had it for 2 years without any repairs.

Sole owner/operator for 6 years using same products that came packed with dishwasher. Bottom rack has simply crumbled away, prong by prong at first and now large sections. Inferior quality of coating and metal used for the forms, means it wont withstand the daily use for which a dishwasher is intended. Worst quality control ever!!

After 22 years, I replaced my Whirlpool, electric, 50 gallon water heater, due to age and it was still working well. Went to Lowe's and they do not carry Whirlpool any longer, so I purchased and installed an A.O. Smith water heater, electric, 50 gallon water heater, model ES12-50R55DV110. Hoping for as good a product now, as I had from my Whirlpool. Also, I installed myself.

We bought this Whirlpool he washer two months ago, and it is the most aggravatingly frustrating washer weve ever had the displeasure to use. There are times when it washes just fine, but I always have to put the mode on deep water wash because the normal mode uses very little water (like its supposed to) but it doesnt clean the clothes. However, most of the time it doesnt wash at all. All the lights will turn off and youll hear this sound and itll drain the water without having been in the wash cycle. Worthless piece of equipment! I prefer the old washer where I have more control. Whirlpool used to be such a good brand, What Is Happening? The new design for their washing machine nowadays generates a lot of complaints, and with good reason (because they suck).