Some years ago I bought a whirlpool water heater from Lowes and the thermocouple went out. No big deal, so I thought. I went to Lowes, picked up a new one and tried to replace it. It wouldnt thread even though the package stated it was for my model. I went back to Lowes and they gave me another one, same problem. So I called Whirlpool, they said it was a left handed thread and they discontinued it, but they could send me a conversion kit at my cost. So at that point I was 2 wks out so I paid for the kit. I received the same thing I bought from Lowes. I was so frustrated I ripped the thing out and got a new one. That was 2 yrs ago and now I am having the same problem. I called whirlpool and they want me to pay for the replacement part. Mind you, the heater has a 6-yr warranty. I went to Lowes and they wont replace it. They sell items that they dont stand behind. I will never buy another whirlpool item and I will never shop at Lowes again.

I just bought my washer 3 or 4 months ago. It is the worst washer I have ever owned. Anyone that has ever done laundry knows you need water to wash clothes. My clothes are not clean and my whites are very dingy. I use the same soap (Tide) and the same bleach (Clorox) that I have used for years. If I can find someone dumb enough to buy it I will sell it and get a good one. I would rather go back to the old wringer washers than this one.

We bought our Whirlpool refrigerator model # WRT318FZDB02 July of 2019. We liked it very much. The beginning of January 2022 we started having issues with things freezing. A few days later nothing got cold. The appliance technician that checked it out said our seals on the compressor were bad and needed a new one. He told us we were better off buying a new refrigerator. I contacted Whirlpool support and they told me the same thing. Our previous refrigerator lasted over 30 years!! I would think Whirlpool would make their refrigerators last longer than 2 1/2 years!!

This dishwasher was a mere 2.2 years old, installed by Lowes-hired technician and the part will cost $168 through Whirlpool, plus labor on both first visit and installation visit. I would not advise to purchase this or similar product from Whirlpool. What really makes me upset is that I learned from customer service that this unit was made in the USA.

In 2014, we redesigned our kitchen for two side kick gorgeous looking white fridge and freezer (Fridge was $1099 & Freezer was $1099, plus extended warranty $436.19 CDN.) Within 2 years the evaporator blew. $1000 dollar repair that Whirlpool covered, yay!. BUT 3.5 years later the compressor blew...another $1000. Whirlpools response...Sorry Sears went under and the fridge is 5.5 years old. Whirlpool discontinued the model so no new fridge for us unless we re-do a whole bank of cabinets. Forewarned is forearmed. Stay away from whirlpool. There are better brands. Do your homework! Sue from Edmonton, Alberta

I will never buy another Whirlpool again or recommend them to anyone, and discourage anyone from buying one. I bought a Cabrio washing machine just over 2 years ago and yesterday I received an F51 error code. The manual says that this code requires a technician to come a check for repairs. Well, before I do anything I google the problem, and lo and behold there are thousands of complaints about this issue with the Cabrio models. Some saying that what needed to be replaced were a control board ($280) and a rotor (unknown amount), not including the price of labor. Some said that Whirlpool knows about this problem and they covered the parts and repair. This didnt get my hopes up, but I called customer service and of course they said that there were no reported issues with the model and that what I found on the internet was probably an older model. Of course! The lady on the phone told me that they would not cover the costs and it would be anywhere from $300 to $500 depending on the route I wanted to take. That is a 1/3 to 1/2 the price I paid for the machine. This is ridiculous! I am tempted to just get rid of the washer and go with a better company that actually cares about their customers. This error code was definitely something they know is a big deal if there was nothing I could do about it other than call a technician. I paid almost $1000 for a machine that has barely lasted 2 years before I have to pay money to have it fixed. Not a company I would ever purchase anything from again!

My side-by-side lasted 2 years 3 months. It stopped cooling. Lost all my food. Inconvenienced by waiting for repair service. Had to take a vacation day from work. This refrigerator replaced a 13 yr old GE and the one in my garage is 25+ years old and still going strong. No help from Whirlpool or Lowes. I will never own a Whirlpool anything ever again.

My wife and I bought a Whirlpool Cabrio washer and dryer set in 2011 and now the washer has an error code of F7 E5. I spoke with an appliance guy and he says that it is going to cost up to $450 to repair it. The wash cycle does nothing, it just sits there and then it goes to the next cycle. I have grown up in a household that had washing machines that lasted many years. This is a joke. Why am I having to buy a new washer in 3 years? I dont understand. Whirlpool knows that this is a problem and they should step up and do a recall or some kind of discount towards a new machine. This is ridiculous.

Whirlpool Cabrio Purchased 12-7-2012 - what a piece of junk. Does not get clothes clean, rarely does she even spin out properly. Called because it kept walking across the basement floor. Informed that was the owners responsibility, not the store (Feidens in Latham). Always had good luck with them, bought all my appliances from them. Now I heard a loud bang and she threw up - water everywhere. What a mess.Had purchased special patio block at Home Depot to even her out and every time I used it which was not too often, it acted like the space shuttle ready to head down the runway! Not too happy with Feidens attitude with regard to this purchase. Not going to call them to fix it. Not an ready to pay to listen to their guff again. Expensive machine never worked well since it got here. I always wished for a Whirlpool, be careful what you wish for! Junk, nothing but junk. Only 3 years old and I only do laundry about every 3 or 4 weeks. Live alone, so she certainly was not overworked.

Model gmh61xvb1 was purchased about 2011 and has had to be fixed 5 times. Now, its down again. My GE microwave lasted 23 years. I thought Whirlpool was supposed to be the best. Boy was I wrong. This has been a real headache. I ordered an LG yesterday. I was in the market for a refrigerator but it will not be a Whirlpool. What has happened to your quality control?

I purchased the model WDF530PAYM0 serial: F14106104 dishwasher. The foremost reason I purchased this was it had nylon racks. I have discovered that the racks are rusting! It is rusting on the ends where nothing can touch it. I am very disappointed that it is advertised having nylon racks and now it is rusting and deteriorating. This dishwasher states racks-nylon, not racks-nylon coated. I just took some pictures of the racks. I decided to look underneath the top rack where the upper spray arm is located. Now I am plain sick! Most of the underneath is rusting. This dishwasher was purchased and installed 2 years ago. I paid $600 and you would assume that something mechanical would quit after years of use on an average of 1 to 2 times per weeks. Not this one...rusting racks and hard telling what damage the rust flaking off during running is causing to the mechanical components. Lesson learned: Their definition of nylon and nylon coated has no difference.....I very much disagree!

I have a Cabrio washing machine and the circuit board has gone bad. I understand from Whirlpools customer service that if your machine was made before 2005, they are fixing the issue. Mine was made after 2006. Even though the problem is the same, Whirlpool will not correct the problem. I was told it was fixed in the new machines. The circuit board goes bad and you have to start and stop the machine at least three times before it will start your cycle, then it stops again at the 17 minute mark and you have to cancel and start the machine again for it to finish its cycle. The error is F1. Customer service acknowledged that this is a known problem for the Whirlpool machines built before 2005 but deny any claim that is is happening to the machines after 2005. Looking at all the other complaints, it is still a problem. I am disappointed in Whirlpool for their customer service attitude and for them not standing behind their product and fixing a known problem. I have always bought Whirlpool products but going forward will be switching to a better company. Shame on you Whirlpool. For a machine I spent $1000 on, the part is going to cost $300 to fix.

I was searching online and stumbled across this site. Funny that there were so many complaints about the console on the ovens, considering that my issue was with the console on a dryer I purchased. I have only had the dryer a year, and it stopped working. There is nothing else wrong with it, no codes, no problems with the lights, or anything else. A technician came out and found that it was a small plastic and metal button piece that helps the press here: spot on the dryer panel to connect to the start button on the console. The little arm had broken and the switch no longer worked.Figured we would have to purchase a new button. NOPE, apparently we were told that we had to purchase a new console (over $200 dollars, close to $300 with shipping)???!!! We were also told that wear and tear can cause the issue. Wear and tear?? On a dryer thats maybe run once a week for about a year? Try again, I think I need my boots because it sounds like horse** to me. I think I will pass this information along to people I know that are technicians so that they can let people know not to purchase from this company because they obviously arent going to address the situation. I think I might also utilize social media to let people know so that they dont have to go through this much aggravation. I certainly dont know what we are going to do, since it took me a year to pay that dryer off, I cant afford another dryer at this time. So unfortunately with a new baby on the way, you wont get any sympathy from me if your company takes a character hit.

Reading the many reviews of malfunctioning washers and other appliances, I wonder why organizations like Consumer Affairs and Consumer Reports do NOT help the many cheated customers form a class action lawsuit or boycott or some other means to effectively organize and force manufacturers to return the full cost of purchase, taxes, shipping, moving and repairs for 5 years for every product. The manufacturer have NO consequences for selling shoddy, malfunctioning but terribly expensive products. We are all being taken for fools by the corporations.I was stupidly brand loyal and bought a Whirlpool Duet front-load washer and dryer because we had to leave our perfectly good 28-yr-old Whirlpool washer when we sold our house. The first set of instruction is to pull the electric cord from a small hole in the back of the washer. No amount of pulling would budge the cord. Finally yanked with all my strength, heard a snapping sound and 12 of cord came out. Then no more pulling, yanking or tugging would produce another inch of cord. So I took off the top of the machine and found the cord tightly wedged in the fork of a plastic thing that looked like part of a stabilizer for the drum.A similar plastic thing on the other side was broken at the fork, the snapping sound I heard. Freed the cord with lots of effort, but it was still firmly stuck way down inside. Removed the back of the machine, found the cord stuck inside a circular thing with one tiny opening. Took lots of time and effort to free the cord from that, but it was still stuck. Finally managed to reach the plug, which was firmly anchored to the bottom of the frame with an orange lanyard. Cut the lanyard with a knife to finally free the cord. This had to be an act of sabotage by an assembly worker, as no way could the cord accidentally jam itself into 3 different places too small for the cord to slip in, and it certainly didnt tie itself to the bottom of the frame with a lanyard.The hour it took to free the cord was just the start of troubles with this machine. It did start and kind of tumbled clothes in an odd fashion, but when it went into spin cycle, it literally jumped all around the room, almost jumping out the door. The whole house shook and I feared the floor would collapse. That machine must weigh well over 100 lbs. even without water and clothes. Next load I tried delicate cycle which had a slow spin cycle.Same result, even worse. I had to wedge my body in the 10 space between washer and dryer and press down with all my 170 lbs. to keep the machine from doing serious damage to the dryer, walls and floor. I contacted seller, Lowes, and they said call Whirlpool. So I did, but no response. Before buying that machine, I read many horrible reviews of Whirlpool Duet machines, but I have only owned 2 washers since 1967, both Whirlpools, so I had strong but stupid brand loyalty.

Mind you, Whirlpool products that we have purchased in the past have been satisfactory, but gas hot water heaters, no! About four years ago we purchased a Whirlpool hot water heater that went out in a little over a year. After spending many calls and time, we found out that the HWH was on soft recall. Whirlpool credited our account, but this was to purchase another Whirlpool, which we did. We paid for installation. About 2 years later, it has gone out. Same problem. Lowes says not their problem. Whirlpool says it will pay for the part only. Plumber will cost 150-200 dollars. All the plumbers I have talked to will not repair them, then they are held responsible when it goes out! As a disabled Vet I cannot afford to throw 400-600 dollars away. And, Whirlpool tells me that if they give me an RA number to replace the HWH, it will have to be a Whirlpool from Lowes. Great! Whirlpool quarterly report looks very good. Mine doesnt look as good. What can be done about a poor working product? Or is this too big to fail? Let me know.

I am so unhappy with my Whirlpool Cabrio washer and dryer. The clothes get so tangled and twisted that it stretches my sweaters totally out of shape. There is not enough water on any of the cycles that really clean your clothes. I saved my money so I could get something energy efficient and look great in my new laundry room. I would never recommend this product. Your sheets will not come clean because they ball up in the middle of the washer and come out partly dry. I have had this set for 3 years and now the bearing is gone; it leaks from the bottom and throws grease all over my new floor. I have battled the horrible odor since the second month. It smells so bad that I make sure I dont wash the day I have guest over. I am so disappointed and mad at myself for not reading any reviews before I spent my hard earned money. So here I am now 3 years into my ownership and having to spend more money on a defective product. The sad part is that I really thought I was getting something nice that would last me and my husband for years. There are only two of us in our household. This machine does not work properly; now it is broken, but hey it really looks good.

I called customer service because my pilot light would not stay lit on my 2005 Whirlpool water heater. I was told that I needed to install the upgrade kit and that the water heater was malfunctioning because of a lack of air and that it needed to be cleaned at the bottom. I paid for the shipping of the kit although I believe it is called an upgrade or conversion kit versus a recall for this water heater to save money and to get the consumer to pay for replacing defective parts. A certified technician installed the kit but the pilot light would not remain lit. He replaced the thermocouple, although new parts had just been received. This did not help either. The technician and I called customer service, which didnt resolve the issue. I also asked for a manager who would only agree to send out another conversion kit. There are three years remaining on the warranty but I am being told to keep replacing new parts with new parts until it works. That is unacceptable. Also, I was not informed that my problem is a recurring problem with this Whirlpool water heater that I purchased at Lowes.

I have a refrigerator model wrs325fdam. Its not a year old and I cant believe the runaround that I am getting from Whirlpool customer service. Come one day everything in freezer melting. Call a repair person. He come out, diagnose the problems, orders $825 worth of parts for a $899 refrigerator, puts the parts in. On the temperature in the freezer reads 80 degrees. No its order $200 more parts for this scrap metal pile. At what point do the people give a damn at the consumer, its not like anybody has common sense. Im going on two weeks without a ten-month-old refrigerator and four days waiting for them to figure this out. Would not recommend Whirlpool to anyone who cares about fair treatment.

2020 Maytag washing machine purchased Sept. 19 2020, never worked from day one. Agitator does not work, makes noise like the machine is struggling to work. Does not rinse detergent out of clothes. Water level is minimal. Went to the dealer Dufresne in Swan River, MB. They sent out a repairman which I paid for, I was informed many customers were complaining that these machines are nothing but garbage. I went back to Dufresne and confronted the sales woman, laughed in my face and told me to leave the store, I was totally taken aback by her rudeness, phoned Whirlpool, spoke to a woman who was very ignorant, I asked to speak to a supervisor who told me thats the way the machines are designed because they are made, DO NOT BUY WHIRLPOOL APPLIANCES, NEVER NEVER.

Its supposed to be energy efficient yet it takes AT LEAST two times as long to get one load done, regardless of size or cycle preference! Now laundry takes all day! Literally! And why is there a lid lockout? Did someone accidentally fall in? If I drop something after Ive pushed start, I have to wait until the machine unlocks the lid. Why? This seems counterproductive. Its a top loader!

This machine needs to go back to the engineering dept. There are too many engineering defects to mention. My Cabrio washer and dryer was delivered October 11th of 2017. It is just my husband and myself so laundry was scarce. I have been unhappy with the washer since the beginning and just recently decided to try and solve the problem. I contacted Whirlpool first and was told these machines have great reviews and nothing is wrong with them. When I started describing the flaws, there was one excuse after another and the person from Whirlpool blew me off. The flaws... all begin with not cleaning which is caused by design. The water level, even with the deep water setting, does not even cover the amount of clothes in a small load; the agitator is so small, there is no effect on agitating the clothes; even with using a SMALL amount of HD detergent, there is always soap residue on the clothes because of the lack of water; and last issue but not final is the load going off balance. The machine will walk all over and error codes according to the repairman need to be cleared so must call if it happened again. Well, the very next load it went off balance again. I did not call because I would have the repairman living with us and I am not willing to set up a bedroom for him or feed him. So, Whirlpool does not care if their product needs redesigning, they only care about selling their product and then the consumer is on their own. Basically the same train of thought from Best Buy where we purchased the machines. Best Buy would be happy to sell me another laundry set... per the store manager but that is all he could do. Will I purchase from Best Buy again... I think you know the answer to that. If they cannot stand behind a product they sell, then they can keep everything they sell, no more money coming from my checkbook to them ever again. Someone, whether the manufacturer or the retailer, should be willing to stand behind their product. But, no one cares. Bottomline, do not believe the ratings on the Cabrio washer. This machine has design flaws that cannot be corrected.

I bought a Whirlpool refrigerator about 1 1/2 years ago. Mechanically it works fine, but many places on the outside are showing small rust, circular rust spots. Looks like the refrigerator has the measles. I dont think ordinary paint will cure the problem since it looks like the rust is coming through from the inside of the door. Any ideas as to what will cure the appearance and keep the rust hidden????

I have a one year old Whirlpool refrigerator which was fine for 6 months. Since then it has been a nightmare. If Lowe’s had not intervened on my behalf, I never would have gotten service. Have had at least 6 service calls, 2 new ice makers and various other parts. It should be bright yellow.

Called Whirlpool about fridge and they stated Too bad its out of warranty. The sides are getting pitted. It is a stainless with black sides. The condo is always air conditioned. It is two years old. Not very long to have a $1200 fridge look terrible. However, the fridge works fine.

We bought the dishwasher as part of our major kitchen remodel. After 1 year, 10 months of successful operation, the wash motor failed. We are now faced with paying about 1/3 of the cost of a new unit, after less than 2 years. I dont expect new appliances to last forever, but less than 2 years is ridiculous. I would definitely not recommend this product to anyone.

Purchased my Whirlpool gas hot water heater. After 1 1/2 yrs, the blinking light shut off, called tech at Whirlpool, made me move hot water heater to outside. I moved it outside and when called back, I was then told to send 4 photos to prove that I moved it, in which I did that. He told me that still was not right... and still he would not help with reset. I live in my parents old home w/ water heater in bathroom for 50 yrs. No problem... it was vented thru ceiling to attic. Now it is outside, unlit, in a steel hub (as directed) and still not ok...I have no hot water and have not for 4 weeks now... Whirlpool sucks... never buy their hot water heaters. Had to pay a serviceman $750 to move heater, run cold/hot water lines and gas line and it still does not work... with NO HELP from Whirlpool. Now I am in process of buying an electric hot water heater and have to pay an electrician to run a 220... I am on fixed income and this stinks... biggest regret... WHIRLPOOL.

I’m getting the run around with service. No one comes to our area to check our new Whirlpool hot water heater. The hot water heater has not worked right since I installed it. I need a service tech to come to my house at Whirlpool’s expense and check the damn thing and get me taken care of. Does Whirlpool want to retain a customer or not? Its that simple. My cell phone number is **.

I purchased the Cabrio washer and dryer 4 years ago and had no problems until recently. The motor and the harness broke and the cost to repair was almost as much as a new washer. The repairman told me that this is a common problem with all washers that Whirlpool makes as they have the same motor and harness. He gave me a list of all the brands that they make and suggested if I buy one to get an extended warranty. I would not recommend anyone buy an appliance from a company that continues to manufacture faulty products. I wonder if they own the extended warranty company?

I purchased a brand new refrigerator model # WRX735SDBM00 Ser # K51621170 on 30 June at Lowes. Paid about 1600.00. Within 5 days the ice maker was no longer functioning. I called the service department and a lengthy ordeal commenced of trying to repair. It is now 13 August 2015 and I have had over 10 visits from a technician and I still have no ice. I made a terrible mistake in not returning the appliance to the store within 30 days so now it has to go through the process which means that now I have to continue to wait until the technicians deem that this appliance is not repairable anymore before I can attempt to get a replacement.In the meantime, we have been inconvenienced, aggravated not to mention not be provided a product that works with no future date where I can get this appliance repaired. The local store management have been great to deal with and are trying but their hands are tied until the manufacturer determines they cant fix. In the meantime, the consumer is continuing to wait for the repair/replacement. No one seems to care or has there been any discussion of some compensation (not necessarily money) for the aggravation and inconvenience I have endured. Something is just not right. Suffice to say, never again will I buy a Whirlpool. HORRIBLE EXPERIENCE.

I have owned Craftmaster 30-gallon hot water heater and the only things reliable about it is trouble and aggravation. I purchased this in 2004. I have had to replace the controls, valves, wires, etc. three times in 10 years. And Im now looking at doing it a fourth time. The design of these parts are utter crap! Cheap plastic! After replacing these parts, this hot water heater works great for a few years, then invariably starts acting up. The pilot light goes out when the heater is supposed to kick on instead. Getting the pilot light lit again, is an exercise in futility! The red reset button once released, immediately extinguishes the ignition flame. Supposedly, after holding it down for 1-2 minutes allowing gas to build up, it should light the coils... and if it doesnt, youre supposed to wait 10 minutes to try relighting again. You can repeat this process for 12 hours, and if you finally do get this temperamental piece of junk to light, youre lucky. Customer Service has been useless in assistance. All they want to do is send you e-mail, and get you off the phone. Not to mention, Ive been told by many a rep that the hot water heater extinguishes itself, if water is overheated, and that it must be my fault for setting the temp too hot. Baloney... Ive been told that the underside vent must be cleaned every few months, so that air flow is accurate. Makes no difference one way or the other. And recently, Ive been told by a rep, that my 40-yr-old house likely doesnt vent exhaust out through the roof properly. This product is inferior and unpredictable. Its great when it works, and the pilot light stays lit. God forbid it ever goes out though! It is next to impossible to relight. I have spent more money on service technicians attempting to repair/replace parts, than it would have cost to simply by a new hot water heater. I miss the old days, when it was easy to light a hot water heater: Strike a match, turn the gas on, and instant hot water. No muss, no fuss. Having owned many properties w/ hot water heaters over the years, I have never encountered such repeat problems, as with this product. Its simply not reliable, and not worth the $$$. Never again, will I buy a Craftmaster Product. And I had no clue that there was a Class Action Suit filed, and a settlement involved in these faulty units. Whirlpool/Craftmaster should have notified everyone, who purchased one of their units. Now Im stuck w/ a constantly broken unit, and zero recourse. I will never buy anything Whirlpool/Craftmaster again, as a result.

These products (Dishwasher, refrigerator, cooktop, and wall ovens) are less than 5 years old and everyone of is in of repair. The cooktop and wall ovens the repair on them would equal the price of a new one. I feel that the products should last more just a few years and also their warranties. This tells me they do not stand by quality of their products.

My elderly mother purchased a Whirlpool Washer Mode Number WTW4955HW1 in November 2020. The washer has had nothing but problems. It leaks, vibrates and moves on the floor. My mother called Home Depot to see what she needs to do, and they said once they deliver the product it is out of their hands. Had our first service call in May 2021 by an authorized service and he said they should sell this on eBay. It is a horrible product, he said there is nothing he can do. Had a second authorized service in June 2021 and they said we needed a new tub which they ordered, and he said this will take up to 2 months, they also said to do only small loads and only use the deep-water wash and deep water rinse. After the technician left the agitator now comes apart. Would not recommend this product to anyone and I would never buy anything at Home Depot because they do stand by the products they sell.

We bought our house in December 2010 and the water heater (fg1f4034t3NOV) just started to give me fits. I had the same pilot light problems everyone else encountered. The person at the 877-251-1679 number gave me a good tip and that may have fixed the problem in the short-term. They told me theres a screen for venting on the bottom of the unit and to use a bottle brush after turning off the unit to clean the screen. I did this yesterday and the pilot light has stayed lit. I called the toll-free number and was told the water heater was out of warranty, but they could send me the part to fix the heater at half-price. I ordered it and they waived ground shipping. I hope to have the situation fixed soon. I’m very pleased with the level of service.

I purchased a Whirlpool washer in 2010. It has started to rust. I called the customer services dept. They told me that there was nothing they could do about it because it was over a year old. I asked to be transferred to a supervisor. She told me the same thing. I told her that its not as if Im looking for a new washer. She said that there was nothing they could do; I had to pay for the repairs myself. I told her, After spending almost $1,000 on a washer, I have to pay for the repairs? She said, Yes, maam. I asked if I could speak to someone over her. She said that she had to take down my name and number and someone would call me back in 24 hrs ... from the management team.She asked for my number and not my name and said someone would be calling back. I told her, How are you going to forward the message without a name? Maam, Im sorry. Whats your name? I doubt if anyone will be calling me back. Whirlpool customer service sucks! They dont know how to treat their customers. Watch out for the warranty. What they call a warranty is not.

Bought a nice house in 2012 which has a Quiet Partner 3 Dishwasher. About twice a week it has to be reset pressing buttons because it blinks at you when you press start. Control board was replaced a couple times since we bought house. We just put up with it. The tub has a manufacturers defect in bottom where the plastic is so thin it finally cracked and over time water trickling out went to wall. Then ruined an area in finished basement ceiling. Ive used a couple different things to stop the leak but it always starts leaking. Customer service says its not under warranty so will buy a new dishwasher. But not Whirlpool or Maytag. Same company now. Dishwasher is a total piece of crap.

Purchased this washer new 2015 for use in our cabin. Now 4 years later with very little use the motor has seized. Washer is useless. What happened to 20 years of almost daily use and still runs great. This washer is a very poor quality washer and has now failed. Please save your money and buy a different brand.

I bought a compact washing machine and 4 months later it broke, needed a CCU board. To make a long story short now the machine is 7 months old and still broke. Whirlpool cant locate a part for it nor do they want to replace it. I think its time to get a Lawyer involved. Ive been calling for weeks now and have gotten nothing but the run around from all very Rude employees. Im turning this over to a lawyer. Im done dealing with Whirlpool. For a large corp Im very aggravated and severely disappointed with them. Wish I never bought their appliances. NEVER AGAIN.

I have clothes that are coming out torn with large holes, especially cotton items. I dont know if it is the washer or dryer.

Bought a Whirlpool fridge in a package from Home Depot three years ago. The fridge has already stopped working. It started having issues about 1 1/2 years in to owning the fridge and finally died 2 weeks ago.

I bought three Whirlpool appliances (fridge, gas dryer and washing machine) from Abt in June 2012, delivered in July 2012. The fridge has not cooled from the moment we plugged it in and because I am out of state from Abt (IL), I have to deal directly with Whirlpool. According to both the Whirlpool customer service rep and her supervisor, if a product is defective from the start, Whirlpools policy is to try and repair it until they determine it to be scrap and only then will they replace/refund. I find this policy appalling since I paid for a good working product, from a company Consumer Reports rates very highly, but was shipped a defective one. Now, I have had two service visits, the second because according to Whirlpool the first technician did not perform the correct service. I have been told not to put anything valuable into my freezer for 5-7 days because most likely I have a coolant leak and the fridge is bad. This is terrible customer service and instead of fixing their error which is the purpose of having customer service, they are quickly building a reputation for a terrible product and terrible service. Good customer service would be replacing the defective fridge as it is clearly their manufacturing issue, taking the item back to their warehouse, repairing it if possible and selling it as reconditioned for a discount. I am noting my suggestion in case any Whirlpool representatives read this website. Another interesting item to note is the gas dryers absorb air from the environment around them so if you do any painting (full room or touch ups), the clothes that come out of the dryer may have a burnt/gas smell for up to 7 days. I am still waiting to hear back from the Whirlpool technician as to my burnt smell problem/resolution, but was told this from a separate service representative so I thought I would pass it on.

Purchased this electric range Maytag model YMES8800FZ1 in September 2017. Thought it was just like my old range with self cleaning mode. Beware! Do Not buy this or anything with this new AquaLift self clean technology. That means youre down on your hands and knées, scrubbing. It doesn’t work. Read all the reviews about this new technology. Salesman never informed us. We innocently bought the range with self cleaning, paid lots of money, for crap! Very upset. Will spread the word for all future buyers, pay attention to the self clean mode on what youre buying, cause no one will tell you. Now trying to reach Maytag, but apparently they don’t care.

I am very disappointed with the purchase of a Whirlpool Cabrio Washer and Dryer I made about 3-4 years. The price was too high and the quality is extremely poor. It has a leak in the pump which will cost me $300.00 to fix. I probably would have been better off buying the cheapest washer and dryer set they had. At least, those actually wash the clothes and dont breakdown. Never again will I buy a Whirlpool and I will get every chance to share my opinion of them.

Whirlpool Cabrio Washer-Dryer - Bought a set a few years ago at Lowes. They are a very attractive set and I was pleased at first. Now, I have had to have repairmen out for these units 3 times. The bearings keep going out on the washer because it spins so fast, it wears them out. Now the thing is leaking. Whatever happened to the days when appliances lasted 15-20 years. For the high cost of these things, they are junk. I am very disappointed. I will never buy one of these again.

I hope the CEO posts this on a giant screen in front of all their employees. The first thing I did after moving into our new home is brag about the American made Whirlpool appliances. Being from the Midwest I take pride in made in the USA product and go out of my way to support homegrown companies. I know that a number of the components in my fridge include the fan that failed after 11 month were most likely sourced and manufactured in China... but that no excuse!! Whirlpool needs to do a better job of QC. You need to be passionate and rigorous with your testing. Dont reduce cost at the cost of your customer base. It is amazing were to the point where we can no longer compete with China in quality.Second is customer service, if you know you cant compete in quality you need to be able to make up for that with customer support. I called Whirlpool and scheduled an appointment the day the fridge quit working. I was upset that it would take three days to have a working fridge but I was understanding. Lucky for me I had an understanding neighbor too. Anyways, when the day came for my scheduled warranty repair I was told that Whirlpool was mistaken and that I wouldnt be able to get it serviced for another week! This is just unacceptable.Right away I called the Whirlpool customer service representative and manager to express my frustration with this error. They were polite and both agreed with my frustration. It also sounded as if they also didnt understand why their own company was doing such a poor job addressing repair issues. They made it sound like this was a common problem of people getting overbook at repair service providers. Again another fumble. Bottom line, due to my position, I dont really have a choice but to wait another week for a repair. Take note: Every time you lose a customer like me this you lose 10! I will now go out of my way to tell people about my negative experience rather than my positive. So disappointed.

We have a built in double oven and we had some early problems with the thermostat. And from time to time the clock resets to 12:00 oclock when there is no other power outage indications. Its also been a challenge understanding the instructions sometimes.

I had the first microwave for 6 years. My husband messed it up so got a new one, same over the stove type. It has lots of programs. Its a rather large microwave, plus it has a steamer which cooks vegetables with steam while I am doing the rest of the meal and whats more important is its quiet. The site is fantastic not just in width but in depth. The best thing about this microwave too is that it has a frozen cycle which does not partially cook the food like most microwaves and the defrost is the same, it does not partially cook it actually defrosts completely without cooking it. This is by far the best microwave I have ever had, and I wouldnt want any other brand. It might cost a little more than the usual brands but its worth it. I also have a mini Whirlpool on my Countertop for my grandchild to use so he keeps away from stovetop at all times.

We bought an 80 gallon lifetime warranty electric water heater. We get about 20 minutes of hot water and then cold water. Weve had 2 plumbers out and checked our system and said it has to be the water heater, but they dont want to mess with it in case it voids the warranty. Fine. We called Whirlpool and since the alarm system isnt indicating an issue, they say its not the water heater. We now have to do a diagnostic ourselves to find out if it is the water heater. What? It has a warranty! We are not plumbers! How come Whirlpool doesnt think its their equipment? Weve already had ours checked and it isnt us! So frustrating and we will not buy another whirlpool product again! Not good customer service to promote repeat buyers. Whirlpool, shame on you.

The front of the stove gets so hot you can burn yourself and I feel it is not safe around small children or grandchildren, and it should addressed to fix the problem not just cover it up. Please give me the info to fix the problem before I have to sue over my grandchildren and great children getting burned.

Why would I, and others buy Whirlpool made washers, with all of these service problems? Now I understand why they have profit/loss statement problems, and stock prices in the pits.

We installed this furnace along with a matching 4ton a/c unit over four years ago. It was installed with a 3 zone computer controlled damper system to separately condition the three floors of our home. This furnace was ideal because it has a dual stage combustion chamber depending on how much demand there is. So besides being 95% efficient, the furnace can run at 70% or 100% heating capacity which saves on utility bills when the whole house doesn't need heat at the same time. It also had a variable speed blower which made start ups and shut downs almost unnoticeable. The blower actually ramps up to speed discreetly and adjusts itself according to the amount of back-pressure it senses. This allows it to respond to varying conditions as each of the 3 thermostats are calling for heating or cooling at different times. And yes here in St. Louis we have had days that require heat on the first floor and a/c on the third floor at the same time. The controller cycles between the two every 15 mintutes. All of these features make it ideal for our 2200sq ft three story brick home(four including the basement where it is installed). This furnace and control system along with new ductwork and dampers were able to replace the two old furnaces and a/c units originally in the home. We haven't had a single problem with it in over four years and would recommend Whirlpool Gold products to anyone I know. If I ever had to do this again in another house I would do exactly the same thing with exactly the same products.

In 2008, we also bought a Whirlpool 40 gallon gas hot water heater with flame lock, Model #BFG14040T3NOV. We too purchased from Lowes. The plumber was here yesterday to replace the thermostat for the third time in 4 years. We also suffered through cold showers, warming water for dishes and sponge baths. We are in our 60s and are worn out arguing with these people. If there should be a class action law suit, you can count us in. It is not right to have such a faulty product out there by Whirlpool. This is still America, right?

I have purchased 2 Ikea/Whirlpool ovens in 2011 from Ikea in Canada. I have used the self clean feature on both ovens and both ovens quit completely and the doors stayed locked. This problem is discussed hundreds of times on the internet for Whirlpool, Ikea and Kitchen Aid ovens. Since they are all made by Whirlpool they are all very similar or exactly the same in some cases, as is the problem. I have discussed this with Ikea and they have said they didnt know about the problem but would help to get it fixed to my satisfaction. I have had Whirlpool authorized service repair both ovens but after trying the self clean feature again, same problem.During one of my conversations with an Ikea representative on the phone, she contacted Whirlpool and was told that if the oven was repaired 3 times and deemed by the service technician as unrepairable, Whirlpool would do a buyback. In other words according to Ikea, Whirlpool would take the oven and pay me what I paid for the oven. Well after contacting the authorized service dept (not Whirlpool itself) for the third time, they did some investigation with Whirlpool about the problem. To his and my amazement, Whirlpool has come up with a fix as of October 2013. The technician ordered the new kit and installed it in both ovens. I have since tried the self clean in one oven and this time it worked. For the information of others, Whirlpool has the kit and in it is an instruction sheet with pictures as to how to replace and install all the parts in the kit.I watched the installation, quite a process. From the instruction sheet there is a number on it. Here is the number - w10625529 rev. A 10/13. This is an instruction sheet for Ikea TOD (thermal overload device) service kit. I have looked at many of the service parts diagrams on the internet for many different current models of Ikea, Whirlpool and Kitchen Aid ovens and in most cases almost all the inside parts are the same or very very similar which leads me to the conclusion that this service kit may work in most of these ovens to correct the same problem, but I suggest checking with the appropriate service people before taking my word for it. My observation is that the kit moves the TOD off the top of the metal plate of the oven and onto a new bracket which the tech thought it was to get it further away from heat (this Im not sure of since Im not an expert). He also suggested that this kit may also be designed to allow more air flow around the oven.My only concern after having the self clean feature finally work is the heat produced inside the kitchen cabinet in which the oven is installed. Approximately an hour and a half after turning the self clean on, I felt the side of the cabinet between it and the fridge (open space), and at one area of the wood cabinet I could not hold my hand on the cabinet as it was too very hot. I will be checking the inside of the cabinet for signs of excess heat and if I see any evidence, I will again call the service people. Since the elements were not on when I checked this, I assume the self clean had finished the heat cycle and was in the process of cooling down. When I test the other oven, I will make sure the elements are still on as I can see them thru the glass door. When I checked the temperature of the outside wood cabinet using a laser thermometer, the outside wood registered 64 degrees C or 142 F approximately. Not sure what the inside temperature was as the oven was still in place. Hopefully I will not get a higher reading when the self clean is at its maximum temperature in the cleaning cycle. Will the oven create any problems in the future for the cabinet, I hope not but time will tell. For clarification, the cabinets were built by a kitchen cabinet company using the instruction sheet that came with the ovens. I hope some of this will be of help to some of the hundreds of people who have posted this very same problem on the internet. When you have paid for an appliance you wanted because of the features it came with, it should provide you with what you paid for and not constantly break down. Im lucky as they came with a 5-year warranty so it hasnt cost me anything yet and hopefully wont in the future. Good luck to all in getting this resolved for all of you.

In July I purchased a Whirlpool Gold oven and cooktop from Lowe’s. It was delivered in Aug. after a 5 wk wait, since it had to be ordered. Since installation, the hot surface light on the cooktop stays on. I called in & was told to try resetting the elec. breaker. Did that... still stays on. Model G7CE3034XB00, Serial D43005649. On Sept. 4th I called & spoke to Carrie (I believe in TN) who told me she would try to find a service tech in my area & would get back to me in 3-5 days. Apx. 5 days later she called & left a message on my cell phone stating that she could not locate a service tech in my area. I would need to find my own service tech & submit any invoices to the resource dept for reimbursement. Parts could be ordered at no charge. I have nothing in writing from the company to confirm I would be reimbursed, nor was I told how to correspond with the resource dept in the event I had an invoice to submit for reimbursement.Today, Sept. 18th, 2014, I called Whirlpool again (800-253-1301) & talked to Stephanie in Michigan. She told me the same info. When I asked to be sent a wiring schematic I was told I didnt need one. When I asked how to get in touch with the resource dept. I was given a fax no. & email acct. When I asked how I was supposed to get in touch if I didnt have either, she said I should go to the local library. Now lets imagine for a moment that I am disabled or live so far out in the country that I cannot get to the library... How am I supposed to get to a fax or email acct. Has anyone at Whirlpool considered that? This is a new appliance under full warranty, yet it has become my job to find a service tech, pay up front, & wait for reimbursement. REALLY??? I am also in the market for a new dishwasher & you can bet it wont be a Whirlpool!

My electric stove is only four years old. In December, 2021, the control panel broke. Digital read out - numbers can’t be read. Service said it is control panel - can’t be found anywhere. Oven has caught on fire twice. House full of smoke. Whirlpool stated my first mistake was not calling them first. I dont have warranty and couldn’t afford a service call so I have DTE protection plan. They sent about appliance repair at their cost. Man said it is control panel and NONE can be found. Whirlpool can’t send THEIR serviceman for another two weeks. I was told to keep circuit breaker on stove pulled. I am 76 and my husband is 84. We can’t go out to eat every night for two reasons: we are on a fixed income - finances will not allow. Plus we both have health issue so I have to cook/bake a certain way. It is going on three months. We can’t afford a new stove every four years. I want Whirlpool to work out some compensation for my stress, aggravation, loss of bakeware that burned in the oven. Took us two days to clean the oven mess, including the glass door - don’t know how it didn’t explode. We had to run downstairs- at 84, moving fast is not that easy, to pull circuit breaker. I could not make two birthday cakes that I had committed to. Can’t bake or make casseroles. We need help of some kind.

This is not a new washer (Whirlpool Cabrio INTW6200VWO) and it works well BUT since we have owned it we have had rust at the bleach dispenser. I am seeing on the internet there are many complaints about this and there was a recall? But they have run out of replacement parts??? Never received any recall notice. We have online instructions on how to repair and have done this many times and the rust comes back. About a week ago we sanded, primed and enamel painted the area plus I have put NO BLEACH in the dispenser and the rust is coming back. I hate to replace a working machine but this rust can and will get on my clothing. Whirlpool was the absolutely best in the past but this one is a lemon.

I have not had any issues with my washing machine yet as I have only had it for two and a half years. The features the machine offers are good and there are many options. So far the washing machine has worked as advertised / expected.

Whirlpool claims this technology works to clean the oven; however after one month of use and one casserole spill, we attempted 3x to use this system and the cleaning process was a total failure. The gravy spill on the bottom and mild oil residue on the sides from roasted vegetables was the same as before the cleaning cycle was tried. The cleaning kit accessory from the company was a joke. It consisted of 2 sponges and a small scraper! We purchased the slide in model WEE745HOFS. Buyers of any and all Whirlpool products with Aqualift BEWARE... It does not work. We have since replaced the product with a range with the traditional cleaning process system that has worked for decades in most major brands.

I am following up on a review I submitted on April 22, 2015 about a Whirlpool refrigerator with french doors and bottom refrigerator. At the time, paint was falling off from the door as pictured in the previous review. This another chapter on this story and probably the closing chapter. A few months after the paint event which I could have lived for a while, the right door hinge literally disintegrated leaving the door without support. The door seals material is of such poor quality that they have disintegrated and the water condenses inside. The bottom photo shows hinge components that came off the door hinge on the kitchen floor. The second photo from the bottom up photo shows how the door scraped the plastic of the freezer door top trim if the door is not lifted to clear it. The second photo from top to bottom shows the door over the hinge pin if I am not careful lifting the door to clear the freezer door.The first photo from top to bottom shows how the door remains open if not lifted so that the door magnetic seal keeps it in place. It is very hard for me to believe that a country like the United States of America treats its customers with no respect. I met my obligation to pay the amount on the price tag of this appliance but I cannot say that Whirlpool did its part of providing a basic quality product. There is no consumer protection agency in this country to protect consumers from corporate predators that have no sense of a fair deal with a customer. So here we are, being abused by United Corporations of America. I hope the future brings a different understanding of the american people on these matters. Thank you for the opportunity to express myself on this matter. Next step... buy a foreign made appliance that will support another country work force... sounds familiar.

Bought this machine in Feb 2007 as a pair Whirlpool Cabrio. I loved it for almost two years. The control board went out, Whirlpool replaced it. A couple of weeks later, the F-1 codes started then the F-51 codes. On July of 10, it was code after code. It sounded like a jet taking off and constant unbalanced load. I called repairman and was told to go buy new machine as repairs would start at $500 and since I live in a rural area, no one wanted to waste their time. Two repair techs told me point blank they wouldnt even touch it. We paid $1000 for this machine and we live pay check to pay check. I spent four months trying to get Whirlpool to do something. I kept getting told I should have bought extended warranty. Machine has been sitting under stairs for over year waiting to see if class action or recall can be done. Also when control board was replaced, the repair man told me it was rusting away from the inside out. My husband had to find us a used washer and this thing has done nothing but cost us money. So much for efficiency. Everyone posting here also needs to go to Whirlpools Facebook page and post there.

I stumbled across this page on another mission and had to stop to add my exp. Perhaps I got lucky and got a good set but Im on my 3rd year and my washer and dryer are my friends. I dont have hot water connected to my washer and my husband is a shingle roofer so I often have to wash his clothes twice but my dogs beds come out beautiful and the sanitizer on the dryer removes odors very well. My water bill went down, I can wash my rugs and large comforters at home now. Plus they are so pretty. Im sorry you are all having so much trouble but I love mine sooo much I just had to stop a moment to throw in a little positive.

This machine (Cabrio) is a piece of junk. It does not fill up with enough water to cover the clothes, even on deep wash and your detergent will still be sitting on top at end of wash and clothes are not clean. It was a $900.00 machine. We need to file a class action law suit. Worthless waste of money. Anyone know of any remedies to get a new machine from Whirlpool or of any class action suits?

I thought with the big tub I would be able to wash my king size bedding and other large things. Theres barely enough water to wash a small regular wash. Since it has no water it does not clean my clothes. Why the big tub if you cant use but one fourth of it?

Ever since I purchased your washing machine, it has sounded like a diesel truck or cement mixer. You cant hear anything over the noise anywhere in the house.Have had two repairmen out to look at it and they say, Thats normal. I have a friend who has the same machine and it doesnt make noise like this one. I will never buy another Whirlpool product again and hope this blows up before the warranty expires. Also the tub is falling apart. What a piece of ** this machine is. You should be ashamed to put trash like that on the market.

I have a washer, dryer, dishwasher, hood vent, stove top, and oven, all Whirlpool. I cant say enough how pleased I am with this product. My old washer and dryer was over 23 years old when I needed to replace them. Thank you Whirlpool for making such a quality product.

Four microwave ovens to finally get one that works. Four months after purchase, the French door fridge accumulated ice, 3/4 thick, in the bottom of the freezer compartment. I had no knowledge of this until the drawer became difficult to open and close. Lowes is replacing the unit.

I bought this washer thinking it would last me for a long time. And now it wont wring out my clothes and I just wanted to say I am disappointed in my Cabrio Washer.

I bought the Whirlpool gas water heater less than 1 year ago from Home Depot. It does not work. The pilot light will not spark to ignite the gas. Customer service is never available when you call, you get a message machine. Going forward, I will never buy a Whirlpool product and I will recommend friends and family to boycott Whirlpool. The 6-year warranty is worthless. You cant rely on the warranty. You cant rely on the water heater. You cant rely on Whirlpool to stand behind their product. The water heater is junk.

I purchased my Cabrio a little over three years ago. Within the first month, the computer board had to be replaced and the tech informed me that it was not a malfunction in the unit; rather, it was because I did not have a sock bag for my socks and panties. I replaced the board, bought a sock bag and had no problems for about 1.5 years. A little over a year ago, the un-level started. I did research and found that I needed to replace the rods and add couplers as they were not thought of when the unit was created. This worked for an entire month. Now, I am in the same position again. It takes about 6 tries per load and the amount of water I am using is increasing with each failed attempt to wash. There should be a recall on this product. I notice there are many other complaints that match my frustrations exactly.

I purchased the French Door refrigerator only 7 months ago. It has been emitting a low pitched, loud, vibrating hum for days. I called the company and spoke with a well-trained representative who informed me that there needs to be a service call. When I mentioned that this did not indicate an acceptable situation for future dependability, I was pitched to purchase an extended warranty. Further… this company doesnt monitor Consumer Affairs. Quality and standing by a product are manufacturer qualities that were not evident during the call.

Cabrio Whirlpool Washer - Bought this washer from HHGregg in Orange Park, Florida. This washing machine is horrible!! It does not fill the tub with water enough to even cover the clothes. Some of the clothes are not even wet. They just sit in dirty water, no agitation. Then it refills with water and the rinse water is dirty, there is no agitation or movement during the wash cycle. My clothes are stained and dried food and dirt are still on the clothes. My white clothes are now gray. This is the worst machine. I have tried everything. I am now hand washing the clothes and trying to add water to at least cover the clothes but the sensor just drains the extra water out. This machine is less than a year old. There should be a class action lawsuit against Whirlpool. I am not the only one; everyone that has this machine says it is a nightmare.

Whirlpool is not what it was before. I got this set with new house... They are very poor construction. They are not even close what I have before the LG. After 6 months I begin to have problems with the dryer... Technician come two time to fix the problems. Quality of washing is OK though... That going to be the last time I got Whirlpool products. For sure.

Had one double wall oven lasted 15 years with just about no problems until the control panel broke and could not be fixed. Bought another just like it and it is having problems after 6 months. Light wont work. Turn on from the control panel and the time does not work.

I love my Whirlpool. Were a family of 3 with a pet dog. Its handle one childs work uniforms and the others sports uniforms (yuck). And then theres my work/weekend clothes. Its very reliable and it gets the job done. We have no complaints.

Whirlpool Cabrio Platinum WTW8800 model - In the words of the service technician who came out finally to service the machine. This machine is a piece of crap that should be recalled from the market. It is a low level-water unit that has no agitator ability in it and does not provide enough water to even slightly clean clothes. Everything must be sorted into the smallest loads possible and even then the clothes dont clean because they beehive into a ball and do not agitate. Technician says the machine cannot be fixed and simply recommends it be trashed (it is 1 1/2 years old). Technician recommends going back to front loaders where at least the clothes agitate. Called Whirlpool for help and was told all system are down...duhhhh. Call back in an hour and Good Luck.

I purchased a Whirlpool fridge in September of 2015. In March of 2016 I noticed the Fridge portion was getting too cold. By April 2016 the freezer stopped freezing and fridge started warming up. I reported the issue to Whirlpool and made an appointment. The day of the appointment the first company called and their tech couldnt make it because of a family emergency. They sent another company out instead. That company diagnosed the issue as a faulty chiller and ordered the part and told me they would be in touch. A week goes by with no working fridge and I call them. They say it will be another week for the parts. Two weeks go by - no call. I call them and they say they have the parts and I make an appointment.The day of the appointment I call them to find out what time they will be out and they tell me they dont have all the parts. And when I mention that I have been without a fridge and that I am frustrated that they arent calling me and that I am having to call them back the lady starts yelling at me asking me if I want to cancel my appointment. So I call Whirlpool and ask for another company. They send a company out that is not trained to be working on a sealed unit. So I call Whirlpool back again and they send an in house tech out three days later. This is over about a month without a fridge at this point. Their tech simply recharges the system and says that it should be fine.A week later the freezer stops freezing and the fridge warms up to the point that both are not usable. The tech comes out and diagnoses that there it is most likely the chiller because of a build up of frost in the freezer. Orders the part and a week and a bit later I call Whirlpool up to get an ETA on the parts. They say they have the parts now (no call??) and they schedule an appointment. The tech comes out and puts the part in almost a week later (2 months now) and says that it is still building up frost in an area that it shouldnt and calls tech support back and forth for the next two hours. He leaves saying give it some time to see if it works, but admits to me that it is likely it is leaking in an area that he cant access.So I call up Whirlpool and explain the situation and ask for a new Fridge. It has been two months and the tech by his own admission could not say he fixed the problem and thought the problem maybe somewhere else. After looking at my case and me being on hold back and forth for about a half hour the supervisor says that at this time I need to wait to see if it fails again. And that if it does I need to have a tech back on site to verify. So this will be the seventh time I took time off work, it will be the fourth time the fridge fails and that I will have to throw out groceries. When is enough enough. I am into this now for almost double what the fridge is worth in lost wages and groceries.Do yourself a favour and stay away from Whirlpool!!! If I have to guess the following will happen: five days from now the fridge will stop working again (when the Freon leaks out - same timeline as previously) and then I have to call for a tech (3-4 days) and the tech will come out, determine that it isnt working. I have another conversation with a supervisor asking for a new fridge and they miraculously agree (yeah I know). Then what two weeks, a month... before I get a new fridge. I anticipate that I will have been without a fridge for 3 months before it is all resolved. Ridiculous is all I can say. Whirlpool should be embarrassed.

I purchased a Whirlpool cook ceramic cook top for our new kitchen. The very first time I made something (it was lentil soup) something stuck to the cook top. I have had a ceramic cook top before for 18 years - never had a problem until the whirlpool cook top. I cannot get it clean. I have tried everything! Such as stove top cleaner designed for whirlpool cook tops ($22), other cook top cleaners, the single edged razor, a scrubby sponge, steel wool, I even resorted to furniture stripper - NOTHING has removed this spot. I am ready to throw out this new stove top! What a huge disappointment this Whirlpool product is.

After almost 5 years of satisfactory performance, our $1200 Whirlpool Duet washing machine WFW9400SU1 requires repairs costing over $1100. Similar to another complaint listed, some parts rusted out, leading to extensive damage during use, which we realized only after the spin cycle became incredibly loud. Now the entire gut of the machine (bearing, drum, arm, casing, etc.) needs to be replaced - $900 parts and $200 labor. I trust my repairman (who said theyd seen this type of problem before with Whirlpool) especially because he recommended buying a new machine instead. I called Whirlpool, and they said they could do nothing for me which made me very angry. This is a mechanical problem that could have been avoided by using proper materials. Whatever happened to the washing machines that would last 15-20 years?

We purchased a Whirlpool 5 top burner gas range in 2008. The oven stopped working. It would click 2-3 times, heat to 100 degrees then stop. Luckily, the range was still in the 1 year warranty. WP sent a tech out who eventually deemed it non-repairable. WP replaced the range. We were sent a letter offering an extended warranty plan May/June 2012. We took advantage considering our troubles with the first range. In October 2012, we noticed the oven started the same problem (2-3 clicks and would not ignite). In addition, the top burner clicks on its own to the point to having to unplug it. Since then, we have not plugged it back in for we feel it’s not safe! We have been working with WP Extended Service Plan (ESP). The obligor is the Federal Warranty Service Corp. for 2 months, ruining our Thanksgiving and now a few weeks till Christmas, our family is still without a range/oven. The ESP claims the damage is from chewed wiring from rodents. We live near fields that have just been cut; mice are coming into our home. However, when the tech came out, finally, he claims there are no chewed wires and the part he has to fix the oven is not worth putting in and will contact the ESP claims department to deem the range/oven non-repairable. This is the second range/oven - its doing the exact same problem as the first but ESP refuses to help us. The last supervisor would not do anything. We requested his ID# and he hung up on us. I contacted WP directly and waiting to if they can help.

I purchased a set of Whirlpool Cabrio Washer/Dryer. After 12 uses of the dryer, it doesnt work and now I have to pay for the service. I didnt think Id need an extended warranty since my other 2 brand name washer/dryers lasted 15 years!

I am writing due to the defects and flaws in my recently purchased appliances. I chose Whirlpool believing I was buying the highest quality for longevity purposes. Every appliance I own is Whirlpool or Maytag - same company. I purchased warranties and was told the warranties dont cover my issues and was basically brushed off. I am infuriated. Here is a list of complaints. Refrigerator is cracking on the inside on the inner door and at the bottom. These cracks surfaced within the first year of purchase. The warranty does not cover cracks in the inner body.The oven/range has an exhaust that bellows out of the top of the range in a way that the smoke curls up onto the panel and discolors it. I have never had an oven constructed with an exhaust pipe in the front that pours smoke onto the range itself and into your house. The dishwasher paint has rusted off on the door as have the screws on the inside of the door. The cover panel on the cleaning dispenser of the washer has popped off and cannot be popped back on, hence the guts of the dispenser are always visible and when I go to load the cleansers the front has to pulled out from inside the dispense.The refrigerator is also leaking from the bottom and the ice-maker no longer produces ice. This started off and on for the past 2 years. At first I thought the leak was from a near by window. No it is the refrigerator. All of these appliances were purchased in 2013, 14 and 15. New. I am 56. I have never had issues like this ever in my life growing up or as an adult. Appliances lasted forever. I am one person. How much damage could I do? None.These are flaws in chemical compounding of the paints and materials for cracks and rust. Whirlpool was called various times and was not interested in sending a rep to verify my claims. They said all of my warranties did not cover such issues only motors. Lots of many spent in vain. I will not purchase Whirlpool again as they seem disinterested in customer satisfaction.

My Whirlpool refrigerator needed a $400 mechanical repair shortly after the 1 year warranty expired. Its only been 13 months since repair, and the refrigerator is experiencing the same problems again! Whirlpool is plagued by negative reviews across the internet... hundreds of complaints on Yelp.ca forums, and consumeraffairs.com. There also used to be hundreds of negative Google reviews, but mysteriously all of those reviews have disappeared, and you can no longer leave a Google review for Whirlpool Corporation.

I love my new stove!! It cleans so much easier than my old one. Would recommend whirlpool to everyone. You cant beat the price for a Whirlpool because it will last way over a decade. My mom has one too and she said, Get a Whirlpool Lyn because they last so long and she said after 10 years hers still looks new!

I exchanged my fancy front loader Cabrio washing machine for a top loader after having numerous issues: clothes werent getting clean, extended water cycle, and a leak. The original purchase was made at Lowes, where I elected to invest in the 3 yr extended warranty plan. After several visits from their sub-contractor, they allowed me to exchange the washer for a top loader Whirlpool Cabrio. At first the washer seemed to work, but after about 8 months I started having problems. The bearings went out and when the service company replaced it they forgot to screw top of the machine together. During my first load, I heard this terrible noise and discovered that the entire top of the machine had separated from the bottom by 2 inches. I frantically rushed to turn the washer off before my laundry room flooded. So, they were out again and screwed the machine back together but failed to retrieve the original screw that they removed from the washer during the first round. Well, the screw got lodged in-between the drum and interior, causing it to completely break the machine. Lowes agreed to exchange the washer for another top loader Cabrio, but my 3 year service contract would not cover the new washer. Not to my surprise, I immediately had issues with it and had to hire a repairman to assess the problem, who concluded that it was the bearings. He informed me that it would be about $700 to replace the bearings and cheaper to just buy a new machine. I called Whirlpool and explained to them about all my issues, now becoming almost comical. They arranged for an outside contractor to assess it. After confirming that the bearing were bad they replaced them. Another few months go by before problems occur, this time the washing machine stopped draining water and spinning. The service company was out another 4 times. They replaced things like the mother board and control panel. My last appointment was today, where the service guy said, There is only one error code. It is a stuck button. I said, Will you at least witness a full cycle so I can show you all my problems: clothes still dirty and stinky, items still wet after spin cycle, cycle taking 2 to 3 hours to run, horrible noises, and timer adding minutes to original cycle. He called Whirlpool because he genuinely felt sorry for my situation. They were of no help. He didnt stay to witness a cycle. Moral of story: if the error code doesnt detect a problem, the consumer will not be helped (this is something that consumers do not have access to). They will happily call a technician out to put a bandaid on an issue until your warranty runs out. I have had between 7 to 10 service calls out to my house, requiring me to take either an entire or 1/2 day off of work each time. If I added up all time lost at work, I could have easily purchased a top-of-the-line washer/dryer duo and been done with all this Whirlpool foolishness. Do yourself a favor, stay away from this product.

I purchased a Whirlpool Refrigerator Model GB2FHDXWB07 a little over 2 years ago. The first one did not work properly within 6 hours of being turned on. Every few minutes it sounded like the compressor was trying to kick on so it hummed then shut off. Best Buy wanted to fix it but after much arguing with them and Whirlpool they brought me a new refrigerator. Now, the same thing is happening. Best Buy has no record of me purchasing it and Whirlpool has no record of me registering the warranty, which would be outdated anyway (over 1 measly year). So, they offered me a Repair and one year warranty $329.95 which means Im now up to about $1500 for a basic refrigerator that has not even lasted 2 1/2 years.The other option to fix it is to pay a local company $90 for the trip and diagnosis plus parts and labor. That will be around $550 depending on how fast the technician works. I will never buy another Whirlpool anything. My washer and dryer also have had problems but I wont even go into that here. The one good thing is the poor girl who took my call was very nice and acted as if this is a regular occurrence. Good luck if you buy a Whirlpool. They are garbage.

Last year, our clothes started coming out too wrinkled. And until recently, its making a loud noise like an airplane. I called Whirlpool, and the only help they can give me is finding a company that would do service and would charge a lot.

I Wish I had reviewed this refrigerator sooner. I bought a Whirlpool side by side refrigerator with ice and water dispenser in the door in 2016. Problem #1: Water leaks from the water dispenser and dribbles down the front of the door. I am as vigilant as I can be about wiping up the spills, but over time it has left a water stain. Stainless steel is not stainless! Problem #2: The freezer is too narrow. Too many frozen items that come packaged in boxes have to be wedged into it or stood on end. Problem #3: Ice cubes sometimes randomly drop out of the dispenser and melt on my hardwood floor. Problem #4: Even though the water is filtered, mineral deposits have built upon the well that collects the drips and I have yet to find any product that cleans it. It looks horrible and filthy. If Id had any idea how awful this appliance would look after just a couple of years, I would have been in contact with Whirlpool immediately.

I bought a new Whirlpool refrigerator from Sears and within a month the refrigerator side did not maintain temperature where milk would not spoil... Cool but never cold. I called Sears and they said its Whirlpool warranty to contact them. This I did and about a week later they contacted a local service company they use to maintain their equipment... Long story short this will be the 4th time they were informed the refrigerator still doesnt maintain temperature... Food had to be thrown out because of that.I asked them to refund me my cost or at minimum get a working refrigerator to me because after 4 attempts at trying to fix the problem it still exists... They just want to keep sending a repairman out there who still cant figure out the problem and that has cost me much time away from work not the mention the spoiled food costs... Even when complaining my dilemma to the repairman he said, All they will do is keep calling us and kick the can down the road... They could care less about what it has cost me in time and money... I had to give 1 star to this company but they dont deserve even that one... Dont waste you time thinking a warranty by them is worth a flip and now over 3 months Im without a refrigerator...

I purchased a high-end Whirlpool dishwasher (WDT710PAYM) a few months ago thinking I was making a wise upgrade. Poor design and it wont dry dishes or properly wash utensils when theyre placed in the utensil rack on the door panel. The unit heavily condenses after using heat dry mode and large water droplets completely cover the top of the inside cabinet. Eventually, they all fall down into the dishes and you now have wet dishes again. The Whirlpool tech’s response was to scratch the cabinet plastic with a scratchy pad, smear rinse aid over the plastic cabinet and that should stop droplets from forming. Whirlpool’s customer service told me they shouldve never told me that and what I should do is be there during the drying cycle and open the cabinet door to let the steam out. This is completely ludicrous. Dont walk but run away from Whirlpool products.

I bought a Whirlpool washer and dryer a little over a year now and the washer is not filling enough water for the cycle to wash properly. I have to fill the washer myself and this only started a couple of months ago. This happens even when I have a heavy supply of water.

I had the biggest nightmare with your sorry company. On 01/05/2013, I purchased a new 50gal electric water heater from Lowes in Waco, TX. I got the unit installed and the damn thing would not heat. I followed your lame support instructions. I contacted your support tech and diagnosed everything possible. I was told I needed to have an electrician to verify that I was getting enough power. That cost me $75.00 bucks and everything checked out. He was not able to check the water heater since he was not a Whirlpool licensed tech. So I called Lowes to return the water heater. Now this is where your policy at Whirlpool suck! Lowes is not allowed to take back/exchange your crap without an RMA number. I had to get it from Whirlpool directly! I called Whirlpools customer service. They flat out refused to do so. They stated that I need to get a certified Whirlpool tech, but it was up to me to contact one! Their nearest one was from Dallas (2 hours away) and could not come out until later next week! I told the tech that its unacceptable! She even refused to get a supervisor! Plus now I blew up on this one. I had to pay the tech $75.00 up front plus the $75.00 an hour to which it would take 2 1/2 hours for repair. Meaning, I would pay more in a damn service call than the actual cost of the new water heater! Oh, but they would refund me in 60-120 days. I would first verify the work was done and if any overcharges, it would not be refunded! So I say to Whirlpool/GE, your warranty policy is a bunch of **. This includes your customer service team as well! I will never ever purchase a Whirlpool or GE product again. Samsung now has my business. May your company fold! Youre a worthless corporation that continues to rip the Americans off!

We purchased a Whirlpool Cabrio Washer approximately 4 years ago thinking we were purchasing a top-of-the-line washer. The first year went great. I was very impressed with how it washed. My clothes came out cleaner than ever before; I loved it. But shortly after the warranty expired, one of the water pumps began leaking out all over the floor. We found out that a coin had passed through the barrel down into the pump and caused the plastic pump to crack with the high speed spin. We replaced that pump at a cost of over $100. We shopped around to find the part as reasonable as possible. The machine worked fine for about another 10 months, then it happened again. The new pump began spitting out water all over the floor. So again, we found another coin, another crack in the pump and again replaced it, another $100+. Finally, a third time, it was the same thing; the pump cracked due to a coin. This time, it was the pump on the opposite side, but still, water was all over the floor. This time, we ordered the part through Whirlpool and complained about this happening for a third time. My husband asked them about the Lemon Law and he was told that he would have had to purchase all of the pumps through Whirlpool. What does that have to do with it? We bought the pumps where we could afford them! The washer cost about $700 to begin with, and within 4 years, weve spent approx. $400 more? Thats not the end of it though. Now we are hearing loud noises and there is water all over the floor again every time you wash. This time, its not the pumps though. It appears that it has something to do with the bearings and maybe a seal somewhere around the barrel itself. But you can hear something knocking around - it sounds almost like a nut. We are going to call a local repairman to come and look at it tomorrow. This is just ridiculous. I feel like weve been completely duped over this purchase. The salesman talked this up like it was the cream of the crop and weve had nothing but problems. My last washing machine was a Kenmore and it lasted nearly 15 years and not once did I have to call a repairman or buy parts for it! Guess what Im going to buy again? If Whirlpool would just acknowledge these problems and fix them for people, it might renew faith in your company. I know I dont know the inner workings of a washing machine, but it seems to me that a screen prior to the pumps to keep coins from entering the pumps wouldve been a very cheap fix to a huge problem. I also own the Cabrio dryer and have hated it since the day I got it. It never dry things with one cycle. I always have to run it a second time. Knock on wood though, I have never had any breakdowns with that. I can guarantee my next buy will not be Whirlpool, nor will I pick expensive models again. I bought the cheap stuff years ago and it lasted forever! Im very nervous because I bought a Whirlpool fridge last year and I am praying I have no problems with that!

Whirlpool g2 convect/micro over the stove oven - This top of the line oven is JUNK, KEEP YOUR MONEY-DO NOT BUY THIS JUNK! I have had problem after problem. Starting after only three months. Defected door switch, touch screen, flashing screen, error message. The service repairman and I are on first name bases. Thank goodness for the, out of my pocket warranty which I no longer plan to keep. I NEED A OVEN AND DEFINITELY NOT A WHIRLPOOL.

I bought this appliance 9 months ago and it has broke 4 times now for the exact same reason. I have set aside 6 separate 4 hour windows for Diamond Factory service to come repair it. All four times, it has been repaired improperly or diagnosed as “nothing wrong with it”. My refrigerator constantly runs, eventually forms an ice wall of back of freezer, and then eventually ice gets so thick to where it stops regulating temperature. All four times, I have had to throw away all my food, defrost the fridge on my brand new hardword floors, and take off work so I can be home for these 4 hour window “service repairs”. They refuse to replace the appliance. UNBELIEVABLE. Never purchasing from Whirlpool or Home Depot in Sunset Hills again.

Cleans average compared to previous dishwashers. Does not dry well even on high heat dry. Cycle takes about two hours and I have to run it during the day because it is too loud. The price was good, but I wish I would have bought a little higher grade.

In the past 8 years, I have had to replace 2 Whirlpool Calypso washing machines and 1 Cabrio washing machine. All 3 washing machines worked great for the first 2 years. I purchased the Whirlpool extended warranty on all 3 washers. The first Calypso had 12 repairs done on it. Finally A&E repair service deemed the washer not repairable. Whirlpool replaced the Calypso with a new Calypso. Based on the problems with the first one, I again, purchased the extended warranty. Again, after the manufacturers warranty expired, I again had issues. After numerous repairs, A&E deemed the washer unrepairable. I contacted Whirpool warranty service and was told that they would reimburse me 75% of the cost of their choice of a Whirlpool washer! Since I have had 10 hand surgeries, I need a washer that does not have an agitator (hence the original Calypso purchase). The model that Whirpool warranty deemed as a replacement had an agitator and was also a much lower energy efficiency rating. I found that the Cabrio was a comparable replacement model and finally Whirlpool agreed to replace the washer at 75%. I was angry that they didnt cover the total replacement, but felt at least I got a totally new problem-free washer. I again purchased the extended warranty. I got the Cabrio in March of 2008. In April of 2011, the washer started getting rust around the bleach dispenser and also I would get UL code (Uneven Load). A&E tech came out and replaced a bearing. He said that the rust was not covered under the warranty. I asked how it was okay to have rust around the bleach dispenser if the washing machine is always wet with water. A month later, I was still having a UL code and the rust was getting worse. A&E came out again and said that even though I saw rust around the bleach dispenser, the rust was in fact underneath the tub and had eaten away at the parts. He called the warranty company to authorize repairs and the Whirlpool warranty company denied any more repairs on the washing machine.

I purchased a Top load Whirlpool washing machine, replacing my old Whirlpool. I am so unhappy with this new one. I noticed that the water level are low...I had the tech here twice and they said that if here isnt any lights on the dash that the machine is working. I called the head tech, same answer. When I put the clothes in the washer I make sure that the clothes are evenly placed in the tub. The clothes comes out tangled and some not clean. Tonight I noticed that a pair of pant at the bottom of the load had white smudges/ I am so unhappy with this piece of junk/ I cant afford to buy another washer, so I am stuck with this.. I have tried all the different controls, still bad. I know the new machine are different than the old ones. I still believe that the water levels controls are not working. I have used my sister new washers and the clothes are not tangled and they are all clean.

I purchased this washers predecessor, the WTW6200 in May of 09, along with the matching dryer. The bearings gave out after 36 months of use, and our household comprises two adults in their mid-fifties. Estimated cost of the repair? $650! Why am I posting this here? Because two weeks ago, my daughter-in-law called to say that shed so liked my machine when she visited in 09 - Id had the thing for two weeks at that time - that shed bought the WTW8500B and... the bearings were already giving out. I suggested she get the thing repaired, sell it immediately and replace it with an LG product, which is what Ive done.She has been put on a three-month waiting list for the repair, confirming my feeling that Whirlpool, as a whole, has gone down the tubes. Their service record is dreadful, with an excess of 20K complaints existing at various consumer agencies regarding ALL the Cabrio line, and their warranty, Ive learned, is considered the worst in the industry. All in all, the single worst purchase of my fifty-odd years.

We bought this 26 cu ft fridge from Nebraska Furniture Mart in April 2017. In November stopped making ice. Was repaired. Now it’s not working again. Multiple enquirers shows this is a common problem with this fridges. I’m debating whether it’s worth the effort to repair it or just put in junkyard. WORTHLESS piece of shiny metal.

I purchased a gas range stove about three to four years ago. I am extremely dissatisfied with this Whirlpool stove. This is the second time the electric ignitors have been replaced due to the stove not working and it is still not working right. The gas valve regulator has also been replaced because it went bad too and my oven still isnt working. I have already put around two hundred dollars in and no one has any idea why it isnt working. Apparently these stoves are a real piece of ** and everyone is having the same type of problems. Something should be done for the customers as it is now. I will never buy Whirlpool again. What a piece of garbage!

Its just OK, the electric cook top heats up slowly, but once heated works OK. Oven is just average! Glass cooktop stains easily and shows some discoloration in places. The glass on the oven door is also discolored on the inside and not cleanable!