I bought my Whirlpool washer/gas dryer 13 years ago and up till now I havent had one service call or repair done on either one of them. I have owned a Whirlpool washer/dryer before and I didnt have any problems with them either. When the time comes and I have to buy another set, there is no doubt in my mind that I purchase Whirlpool products again!

Bought a $2500.00 fridge in Dec. 2012. By July, we were dealing with our 4th repair. Customer service in warranty department is non-existent. They act like you are a bother and have no right to demand replacement. I sent an email. No response. I wrote a letter to Corporate. No response. Not until I made comments on Facebook. Then I get a call offering me an extended warranty (which I already had purchased) so they said they would give another year (total of 3). This was a few weeks ago. I still have yet to receive anything or hear anything. This morning, our fridge is on the fritz again. I am loathe to have to deal with them again, but have no choice. Its either deal with them or throw out the 8 month old unit and buy something else. I should not even have to consider that. Whirlpool is a huge company. I do not understand their reluctance to just replace a product that is obviously defective unless they have no confidence in a replacement unit. This is so frustrating and upsetting to me. I did my research. I thought I was getting a quality product from a quality company. What a disappointment.

We purchased this Whirlpool pair after our upright machine was unable to be repaired... because of parts coming from China and being hard, if not, impossible to get. We have had this pair for about 2 years now (Lowe’s). It still doesnt clean the clothes and it continually goes off balance when doing sheets, comforters etc. Myself I feel since they have taken the middle agitator out of the machine - it no longer performs the way a washer should and that its main function is to get the clothes clean! I did write a letter to Whirlpool about it and they pretty much told me, “Well too bad.” So much for buying American made products... at least the upright did last 6 years!

Very unhappy all the way around with Whirlpool. The first refrigerator shipped had to be replaced, I do not remember the original problem, just the ordeal involved. The replacement had to have the computer board replaced twice, the icemaker stopped working after a few months, the freezer door does not seal properly. And now, after less than 3 years, the drain is clogged. After researching, come to find out this is a common problem and has resulted in many water damaged wood floors, including my own. Never Whirlpool again. There are much better brands on the market today with better price points. I highly recommend staying away from Whirlpool.

They really dont make them like they use to, do they? This Whirlpool Cabrio aka Caprio has given us problems for the past 3 years, weve owned it for 5 years. It doesnt matter how much, or how little clothing you put in this washer machine. It will start going NUTS, Thudding, Banging against the inside of itself, completely out of whack, and then it will show a UL where the time is shown. Every time we do laundry this happens, and we have to stick our hands in the hot water and reorganize the clothes, and pull more and more clothes out till theres only about 3 items of clothing left! This washer is GARBAGE! I advise people to keep away from it. The washer we had in the past lasted us years upon years. These washers of now in days are Crap Garbage. Keep the fancy tech look, and give me the old fashion Knobs ANY DAY! Whirlpool brand is Not what it once was.

This refrigerator well paid for itself. I had over 25 years and it was still in good working condition. I had to leave it behind. I moved to a place where fridge was already. I hated to leave it behind. ‘twas offered to Goodwill but they never answered the phone for it. I surely hope someone got it.

I purchased the Whirlpool Cabrio Top Load Washer in 2009. It stopped working and I found that it needs a new control panel and recirculating pump which will cost $390, including labor (plus the cost of the service call to diagnose the problem). I would not have expected to have this type of problem with a washer within 3 years of purchase. I cannot recommend this machine.

Have had Refrigerator less than two years and the evaporator seal is leaking and all the Freon is gone causing the freezer and ice maker to quit. Will cost $700 to repair. Found out it is a known defect with Whirlpool. Called Whirlpool for reimbursement and they refused, saying they do not know anything about this issue. This is interesting since it is all over the Web with complaints. I have been a customer of Whirlpool for 20 years and they have lost me and everyone else I know.

I thought the Calypso had issues until I got the Cabrio. It does not use enough water to get the clothes clean, it leaves them in a tangled mess, and no matter how carefully I load the clothes it is always off-balance making enough noise to wake the dead!

I called the dealers repair department, which said they had not seen this before and it looks defective. I have used the oven less than a dozen times. It is virtually new. They submitted pictures to Whirlpool. The oven surround is not replaceable, so the request is to get a new oven. Whirlpool responded with, This is normal... when the cracks break through, then there is a problem. What?! I have been cooking for over 50 years and have never had this experience before. This product is under warranty. By the time it cracks through, it will be too late to do anything about it. Since when is crazing on the oven bottom natural, especially after only a very few times used? This is defective and Whirlpool is shirking their warranty. I am very dissatisfied.

Recently had a Whirlpool gas water heater installed. Would smell gas every time the heater kicked on. I inspected the vent, all the new fittings, with no luck. Leaving the windows open didnt help. Finally found the problem: the factory-installed line from the gas control valve to the tank was leaking. Should have kept my old heater. It was still working flawlessly after 20 years. You would think a new heater would at least be inspected before hitting the market.

When I bought my new retirement home, a Whirlpool dishwasher Model No. DU1055XTVS1 had been installed. After only three years of use, the dishwasher would not complete a cycle except to drain and cancel. The repairman replaced a computer board and when the parts cost and the service cost were combined, they amounted to about half the cost of the dishwasher. I have a PC that is twice the age of the dishwasher and it is still running.

Purchased this washer new 2015 for use in our cabin. Now 4 years later with very little use the motor has seized. Washer is useless. What happened to 20 years of almost daily use and still runs great. This washer is a very poor quality washer and has now failed. Please save your money and buy a different brand.

Bought a Whirlpool Cabrio HE washer over a year ago. Recently, the spin and drain cycle stopped working. Went to find a repair person only to learn that many dont work on this model because of all of its problems. Did find a company who replaced a part ($100). Now sounds like a thrashing machine when it spins. However, now the machine wont even go through a regular cycle. Dont buy this brand!

Whirlpool N50T61-403 - I bought this thing today 8.21.14 from Lowes. It is a Whirlpool 50-Gal water heater (6th sense) and was going to have it installed by their installer, but elected after seeing it was very similar to lining up with my old unit. I got it in and then filled it. After filling, I lit the pilot light per the instructions then turned the knob for heating it up. Success, the flame spread across the burners...then went out. The steady blink changed to the 2 blink code indicating a bad thermopile. It did not work - right out of the box. No plumber near me carries the part. Whirlpool has thus been pretty good about it offering to have someone come out at their cost... But if no one has the parts, that is no good. I am moving from this house so if we can get it to work, its the problem for the next owner. If not - Ill have to get an RMA and go back to Lowes... Then try the Rheem from Home Depot. Will see if they will overnight a part tomorrow. I found the other reviews - and I dont like it that this thing appears to have difficulty right out of the box.

1st item - ice pooling at bottom of freezer, now repaired at a cost of $100. 2nd item - 1 day later fridge/freezer keeps shutting off and on irregularly. Cant contact anyone one from Whirlpool on a weekend and Trail Appliances doesnt have anyone available to come and look at it and if they did it would cost us another $100+ with no guarantee and we were told by Trail the Whirlpool will not touch it if someone else does. From what I have read seems we now a victim of Whirlpool. P.s. for those who dont know yet Whirlpool not only now owns Bastemp, they also are the makers of Kenmore and those fridges have experience the same ice issues.

I also have the same water running into the refrigerator problem that so many people have reported. Im about to throw the Whirlpool out and start over. It is such poor business that whirlpool wont admit that the appliance has a major problem and fess up to correcting it for owners. I will never buy another Whirlpool appliance and will warn everyone to also steer clear of Whirlpool.

I purchased the Whirlpool Cabrio Washer thinking I was purchasing a quality product. Unfortunately it was one of the worst decision my wife and I have made. The bearings (lower) only last about 2 years. We purchased the extended warranty and the first time it was covered. The second set were not covered and now we will have to change them again. We will not ever purchase another Whirlpool product. I contacted them several times with no positive results. I still saved the last worn out bearings to show the CEO. The engineers do not have a very good idea to make the lower bearing last. Where I purchased the machine they told me after the first change that it would happen again and they were correct. If anyone needs to contact me about this product feel free. NEVER EVER BUY A WHIRLPOOL PRODUCT.

First F1 symbol on washer took 6 months to resolve. All we needed was new motherboard and couldnt mail it to us even though we could replace. It had to be an authorized person. Well we had one and they never put him in the system. Finally got that taken care of, 6 months of having to press pause and restart 5 times just to do one load. Arrrrrggggghhhh! Now water leaking out the bottom. Called again, on hold, then on hold again to be transferred to tech support. Yeah, right. No tech support. Talked to management, they could care less about us even though we have other products from them. Dont buy, they are lemons. We had ropes for 15 years and lasted through everything. Thanks Whirlpool, heres to losing a customer!!!!

Whirlpool refrigerators with bottom freezers have a major defect in a tiny drainage hole hidden inside the back panel. The hole easily gets blocked with bits of debris during manufacturing or with a few bread crumbs, then it freezes shut. Then water ends up all over your floor. You cannot fix it yourself as you have to take apart the whole freezer. The repair bill is huge. This will happen often. Check on the internet and YouTube to verify & you will see that this happens to everyone with a Whirlpool. Also your floor will be ruined if you dont mop it up every few days until the repairman arrives! Stay away from Whirlpool!!

My Whirlpool Cabrio WTW7800 was bought 1 and 1/2 years ago. The lid is glass with a plastic edge. The plastic part of the lid next to the glass and hinge is cracking causing the glass to stick up. It is cracked from the top of the lid toward the base if the lid were closed. The only way this could happen if it werent a manufacturer defect would be if someone were to get inside of the washer with the lid locked and try to push up to get out right at the hinges. I have noticed several other complaints of the same problem on this website with the same model. Clearly this is a manufacturer defect. I am on the phone with Whirlpool now.

I just bought this water heater on 2/12/12 and it has already started having problems. I got a self diagnosis of the gas valve needing to be replaced. I think that if this becomes an ongoing problem, whether I have a warranty or not, I’m going to trash it and go with another brand. I shouldn’t have to pay to have the gas valve replaced.

In 2007 and 2008, I purchased 7 natural gas heaters: 1 for my home and 6 for rental properties. I have had nothing but problems from all of them. Two of them failed this weekend (one 40-gallon and one 50-gallon). I called the 800 number and have to pay $63.50 for parts for the 40-gallon and was given a PO number to pick up parts for the 50-gallon at Lowes. They do not have the parts. I have spent over $250,000 at Lowes since 2000. I have all Whirlpool appliances in rentals and my own home. The discussion I had at two Lowes stores today really showed me how they take care of their customers. I told both stores that I will never buy the Whirlpool brand again!

I bought a dishwasher Gold Series Top Control Whirlpool dishwasher at the Home Depot, April 4, 2015. Paid six hundred ten dollars and twenty-eight cents $610. 28. I noticed soon after that the top shelf falls off the rack when loading at front. I began loading from the back. It worked for a while but now it totally fall apart. The door will not close and I am unable to use the machine.

Bought Whirlpool French door refrigerator. Unit was defective when delivered and I told them so. That was on 06/14/2013. Unit got progressively worse and finally has quit completely. At Whirlpools suggestion we bought a Whirlpool Repair Plan Plus One (another scam) for $300. Repairman came out and told us the refrigerator couldnt be fixed. Now Whirlpool suggests their only option is for us to buy a discounted model. This refrigerator went from bad to not working at all in less than a year and a half. Anyone that buys a Whirlpool appliance with knowledge of how they treat customers and back their products has to be a little crazy.

Ive owned whirlpool appliances for forty years or more, and have been consistently pleased with them. My first washer and dryer lasted eighteen years while raising a family. Brand X lasted eight years with at least four repairs before we dumped the set. We moved and sold one set with the house, but my newest washer and dryer set is eleven years, and works fine. Ive had at least four ranges. We sold two of them with the houses, but theyve all been fine, just bought a snazzy new Whirlpool range as an upgrade. Im on my fourth Whirlpool refrigerator, but again we sold one with the house and we upgraded one perfectly good Whirlpool refrigerator to a bigger side by side with icemaker. Third whirlpool dishwasher. Weve moved a lot, leaving behind appliances and buying new ones. Sure, Whirlpool appliances break down, but they sell zillions of them, and you never hear about the zillions that never break down.

Whirlpool 2 Cu. Ft. Stainless Steel Over-the-Range Microwave - My wife and I have just remodeled our kitchen and we bought all the Whirlpool appliances, fridge, stove and microwave. We have had them for about 3 weeks now and now the display on the microwave just stop working. I just cant believe this. Its going to be a real pain now to remove this and replace it. Has anybody else had this problem and I wonder if its even covered under its warranty.

I like the newer technology that is built into the washer. My only complaint is that the wash time is automatically set depending on your load choice. For instance, a delicate load is set to wash for 45 minutes. I dont feel that amount of time is required.

I have been unhappy with my Whirlpool Cabrio washer since I purchased it from Lowes. I should have looked online before I bought it and then I would not have made the mistake of buying it. The washer leaves soap deposits on the clothes and sometimes leaves a colored soil. It has ruined numerous clothing by tearing out hems of towels and wash cloths and tore a hole in a favorite sweater. I prefer an agitator in my washer. From what I read, I will soon begin to have other major problems and then I will replace it, but not with a Whirlpool.

Purchased my Whirlpool Duet front load washer WFW9150WW00 new in 2010. Also purchased extended warranty. After four years, just before my extended warranty was up, the entire inside needed replacing (drums, bearings). Now at only five years old, it keeps making a beeping noise in middle of wash cycle and wont continue working. Serviceman was told by a Whirlpool tech. that it could be two things, one being the door jamb, the other being the control panel. Door jamb was fine. Ordered new control panel ($240), had it installed and yet the washing machine still keeps beeping and doing the same thing. The serviceman doesnt know what else it could be. So, I am forced to return the part and purchase a new washing machine. I would never recommend Whirlpool to anyone!

This Whirlpool washing machine is incredibly annoying and slow in everything it does. First off when you press the START button it takes 2-3 minutes before it decides to do anything, like maybe add water (except click, click and more click). If you have pressed the start button and you want to stop it to add something... again you have to wait almost 2-3 minutes before the lock is released and you can open the door. I am at 2 hrs and 15 minutes as I write this on the LIGHT WASH cycle with extra rinse and its still going. I have never seen anything like it. Cant imagine how long a HEAVY CYCLE takes. Cannot even try to measure the time. I put the load in and go to work and hope its complete when Im done 8 hrs later.We had a Maytag for 15 years with no issues (other than a drain hose cracked and had to be replaced) and it was time for a new one with a move to a new place. The sales associate convinced us this was the best machine at the time... Well what a mistake that was. There are no complaints about the actual washing. Everything comes out clean but I suppose taking that long I cant imagine why it wouldnt. I certainly cant recommend a Whirlpool washer to a friend, because I dread the thought of doing laundry at this point.

This microwave came with the apartment. Its the 2nd one we have had. The first one failed in our 3rd year here. We dont use all the functions, but what we have used, it works fine. Would I purchase this brand, no. I would choose GE, or Panasonic.

My Whirlpool oven (Model WFG505M0BS0) stopped working - the bottom oven part (the top burners were OK), the display on top functioned normally, but no fire came on. I called Whirlpool, and then I accessed Whirlpool online and scheduled service with their official service representative - Flamingo Appliance Service ** for September 9, 2020. When the repairman arrived on 09-09-2020, he opened up the stove and checked it, and he told me that a computer part needs to be replaced, as well as the igniter, and the cost would be between $400.00 and $600.00 (I dont remember the exact amount), I told SEVERAL times, maybe its just the igniter (for which the cost would less than $100.00 AND already included in the $134.95), but he insisted that the computer needed to be replaced, I did not like the way he explained it to me, it did not make sense.After that I was planning to buy a new stove, as the repair was too high. But, I decided to try to change the igniter myself before getting rid of the stove (the igniter cost was $21.00). I just got the igniter recently, and installed it, with help from YouTube, and what do you? THE STOVE IS WORKING!!! This is fraud!!! FLAMINGO APPLIANCE SERVICE ARE THIEVES, AND BY ASSOCIATION, WHIRLPOOL, WHOM THEY REPRESENT ARE THIEVES ALSO. I shall publicize to the best of my abilities: NOT TO BUY WHIRLPOOL PRODUCTS!!! This was not a mistake!!! This is the way they rip people off!! Either by paying exorbitant amounts for unnecessary repairs, or by buying new appliances when the old ones are still good. Dont buy Whirlpool!!! Dont use Flamingo Appliance Service. Theyre both fraudsters.

My 1 year old Whirlpool top loader is an absolute nightmare. It does not complete cycles. Stops all the time with various error codes. My washing comes out soaking wet. The pipes on the inside comes loose and floods the house. The machine stops all the time with all the washing clogged on one side of the drum. It is a 16 kg capacity machine but you cannot even think of putting 8 kg laundry in there. I will never, ever buy any Whirlpool product again. Cheap scrap! Thats what it is.

We bought the washer and dryer set almost three years ago. Great sales pitch! Energy saver, extra capacity, low water usage, Whirlpool name and I thought we were getting great quality! Three years later I am disgusted, disappointed and am junking the washer. The dryer has a new heating element that we proudly fixed ourselves after the repairmen told us that these were meant to be throwaways. We just thought he did not want to work on it. After watching several YouTube videos we had it apart and found the issue was a cracked heating element. We ordered a new one for 100$ and spent another 4 hours putting it back together. If we had to pay a repairmen to do all that the bill would have been the price of a cheap new one. Fast forward three weeks and now the washer quit and it can be one of at least 15 problems. After reading all these reviews we have decided to toss it as junk. It took forever to was a load of clothes negating any energy saving! Whirlpool should be ashamed of themselves for ripping off all of us hardworking Americans selling us junk. At one time the Whirlpool name meant you could count on a quality product! If Whirlpool really wanted to do the right thing, they would stop selling these immediately and give customers a credit toward the purchase of new washers and dryers!

I purchased a Whirlpool French door refrigerator model # gx5fhdxvyo4 in June 2011. Four months ago, ice was forming on the bottom of the freezer. Repair person replaced a clogged plug leading to evaporation tray. Its March 2013 and repair person now has to replace evaporator motor part # W10128551. I contacted Whirlpool and was told the warranty has expired (one year). This repair will be around $175. How can I trust a Whirlpool product in the future?

My wife dropped a liter of pop 12 inches and broke the plastic shelf on pantry door. When I called Whirlpool, I was told its under use and abuse and they wont pay for the repair. It is an electronic component because of the pantry door. I asked to speak with a supervisor who would only apologize... I asked for the phone number to Corporate and was told there is no number, no email, just a street address to send a letter. How 1950s of them. Owned fridge for 4 months paid for the extended warranty and now I can pay $200 plus or look at a cracked shelf.

Purchased a 80 gallon Whirlpool Water Heater with a Life Time Warranty. When it overflowed because the system failed to detect the water temperature, called and they sent in the temp sensor (I paid for shipping). Had plumber replace it. One day later the same thing happened, called and they sent in a board. Same exact thing happened. By this time, Im without hot water for over 2 weeks in dead cold January on the East coast. They will replace the water heater but only a 50 gallon NOT the 80 because they no longer manufactured the 80. Option given by Lowes is to add a recirculating pump to give additional gallons. But, of course Whirlpool said NO. They only can give me the 50 gallon. What a ripoff!!! Please, please DO NOT purchase any product from Whirlpool. Now they change the same to A.O. Smith Signature Premier.

My Whirlpool water heater had to be replaced. I got a new water heater, and filed a complaint against Chris from your company. Talked to Chris, and he requested for paperwork on the old warranty. I tried to send it through fax number 1 800 999 9210, but got no response. Chris, please reply with the fax number so I can send the info you requested

Whirl Pool Duet Wash WFW9400SW - I had this washer for 5-1/2 years. I use it about 3 times a month. Warranty ran out this last February. Machine stopped working. Called tech and he came and said I need a new console and power board. Two weeks later I get told they dont make it anymore and sorry about your luck. I used this washer under 200 times in 5 and half years. Whirlpool offered nothing and I will never buy a Whirlpool product again.

Absolutely love the oven/range electric smooth top! Cleans up well. Works well. We bought new along with refrigerator and microwave as a set. We had problem with icemaker, told us we needed new door (well within warranty coverage) then wrong door was sent and company told us that they could only send one door and that was it. Incorrect door sent back. Repairman attempted to fix several more times. We finally quit trying. Husband says we can never buy Whirlpool again.

The control panel is difficult to use. It’s much too easy to switch power from the top oven to the bottom oven without knowing it. In addition, the plastic cover over the control panel makes it difficult to use especially if your fingers have flour or oil on them. It would be much easier and more accurate if knobs were used to control the all the functions instead of a electronic screen. Also, the clock has never operated accurately. Always runs fast. Temperature of the ovens is pretty accurate. However, it does take a long time to reach chosen temperature. Both ovens are large and able to handle an 18 inch round pizza dish. Other than the control panel, I’m pleased with both the gas stove top and both electric ovens.

Just bought a Whirlpool stove (WFE540H0ES) from Home Depot. Oven gave off so much heat around the handle that I burned myself opening the door... Tech came out said it wasnt supposed to do that. Called into Whirlpool to get clearance for a replacement and corporate says no to the replacement because that is normal. Thats BS! If that is normal DONT BUY A WHIRLPOOL!! BTW... They are owned by Maytag.

My wife and I have had a Whirlpool Gold 5.8 cu ft gas range for just 5 months and have already begun to have intermittent trouble with it. She can use the oven to bake cookies in the afternoon and then try to bake dinner a couple of hours later and the oven will not preheat no matter how long she waits!! This has happened three times now and we are waiting for a service technician to come out.. Pretty sad when you buy a top of the line appliance and begin to have trouble so soon.

I purchased my Cabrio washer and dryer 2 1/2 years ago, and for the past 6 months, I have dealt with it being unbalanced and I tried everything to get it balanced. When I researched the problems, I found so many other consumers are having the same problems and that Whirlpool will do nothing about it. I decided to start a petition on Change website to try to force Whirlpool to stand behind their product and correct the problem, offer us a refund or another product, or even fix the darn thing. It is tough economic times, and we spent money to have something that was energy-efficient as well as a product that is supposed to carry a good name. I am a single mother with three children, and I dont have a $1000.00 to throw away after 2 years. This is shameful that we, the consumers, have to deal with this. Please go to the Change website and sign my petition. The more signatures I get, the more leverage we have to deal with Whirlpool. Lets pull together and show Whirlpool we will not stand for them robbing us of a quality product. Thank you so very much.

We purchased the gold series model WDT790SAYM1 in 2013 replacing a 12 year old Maytag we were very happy with. The Whirlpool just does not clean very well and leaves dishes dirty no matter which cycle you use. The spray arms are cheaply made and do not work well. Its a piece of crap compared to the old Maytag. Do not buy any dishwashers from Whirlpool, they are simply inferior products and a waste of money.

I purchased this Cabrio top loader washing machine (model #WTW5640XW3) after I had a Kenmore front loader for 14 years with not one problem. I bought the Cabrio thinking it was good for the price. Well, let me tell you first of all, I dont like the no agitator. The salesman said it was a big seller. I started doing wash and it was smelling like dirty socks when it was done. I own the machine for two months. I cleaned the machine with Afresh thinking the smell on my clean clothes was from being a new machine. Imagine that I have to use extra fabric softener, vinegar. I dont know what to do. This machine stinks. I am going to try to return it. Wish me luck. I dont think it washes right.

My stainless steel french door refrigerators compressor quit working and needed replaced after 3 years and 10 months. I had to buy a replacement kit and it cost 400.00. The repairman cost 175.00. I tried to buy an extended warranty but they do not sell them. You get a 1 year warranty. The repairman told me you will be very lucky if you get 4 years out of the replacement. He said all of the new compressors are really junk. Remember when refrigerators used to last 30 to 40 years. Not anymore. It is a money racket. Do not buy anything Energy Star, it is all junk. I have gone through 5 washing machines in 18 years, and I live here by myself.

My Whirlpool washing machine is really easy to use. It is a mid-range machine but it has all the bells and whistles. Its a joy to use. It gets my clothes nice and clean. It does a great job. I would definitely buy another Whirlpool washing machine.

I paid $1246 for a Whirlpool glass top range. This was not a cheap model, but I wanted it as the starting point of my new kitchen. After only about a year, we noticed that the area surrounding the operation controls was turning a funny color. On closer inspection, we noticed what appeared to be something peeling off, it was paint! The area surrounding the controls, which appeared to be brushed metal, was actually painted plastic! I was furious that an appliance at this cost level was made of plastic....really, a stove top made of painted plastic? I complained and after a huge fuss they agreed to come out and replace it ONCE. Well its been just over a year since they replaced it, and guess what? It is peeling off again!I dont know what to do, as Whirlpool obviously has gone the cheap end and doesnt want to fix problems. As others have mentioned, they say that it is JUST cosmetic, and they wont cover it under warranty...now my first new appliance for my first new kitchen since 1972 looks like crap! I should have kept my old avocado green appliances - they lasted over 40 years, still worked, and still looked good (except they were green). I wont ever buy another Whirlpool appliance. For those who mentioned that their appliance would turn on unexpectedly, please check recalls....this is one of the major problems on recall. Buyer beware!!!!

Purchased this oven on 9/12 from Sears, did not purchase an extended warranty and didnt think it was necessary. Im a 64 year old widow and only use the oven on holidays, to date Ive used the over 5 times. With Easter coming, I decided to clean the oven. Followed the instructions, the door locked and the oven died. Im totally disappointed, now it would cost over 100.00 to repair, money I cannot afford. Called Sears and all I was told over and over again that they can send a repaid person and I would have to pay. I was also told that I should have purchased a Kenmore and I wouldnt have had a problem and finally I was told that they couldnt fix it and referred me to whirlpool customer service, who also told me it would cost over 100.00. A 19 month oven should not have died. It should have cleaned the oven and continue to work for many more years. Again, Im upset, angry and disappointed with sears & whirlpool. And dont know what to do. Does anyone else have this problem with the oven, is there a recall?

August 26th 2014 purchased a NG (NO GOOD actually natural gas) Whirlpool water heater from Lowes. Model No. N40561-403. Installed it and everything was fine until this morning August 29th 2014. The indicator light was out and so was the pilot. Tried to light it without success. Called Whirlpool and they are sending me a new controller that now needs to be installed. Called Lowes and they will not take it back. Wish I would have found this site prior to this costly fiasco. Waiting on part now and I will keep you informed as to my progress. I have a feeling this is going to be 2 days wasted and $367.00.

I purchased this piece of crap excuse for a washing machine, the Whirlpool Cabrio, almost 2 years ago, in September, 2015. Since that time I have had nothing but dissatisfaction about how it washes, and the extremely poor results. I contacted my sales associate early on, I was told, just like others who have purchased this machine, that it was a water-saving machine, and I needed to read the manual closely and just do what it said to do. I did that. Long story short, I am sick and tired of this machine, stopped using it, bought another machine that lets me choose how much water for each and every cycle, it washes extremely well, my clothes come out clean, it HAS AN AGITATOR, DIFFERENT BRAND, and I am very HAPPY with it! I will never ever buy a Whirlpool product again. I am well-known, have an extremely large number of friends, and I will be spreading the word that Whirlpool built a piece of crap. Never mind that piece of crap washing machine was mandated per government regulations to cut down on water, thats a bunch of crap. Users should not have to buy expensive cleaners, tote extra water to a washing machine that uses so little water that it barely covers the clothes, and no person should have to use a product like this. Never. Washed clothes from this machine stink, the odors will not leave my clothes, whites are now yellow, stained, and colors have white spots on them. Whirlpool, you have built this piece of crap, I hope you have large heapings of Karma! What a joke. What a useless company now, sell out and go play on the beach. You deserve the dirt, not your use-to-be-loyal customers.

We have had our washer just over a year when the plastic hose that fills the detergent tray began leaking. The entire assembly is plastic and poor quality. Whirlpool customer service says since it is after 1 year, that I would need to pay for the parts & service ($489). I would not recommend this machine or anything Whirlpool.

I purchased a Whirlpool electric stove WFE540HOES 3 weeks ago from Best Buy. 2 Main complaints: Extended cooking time when using the oven. Food that should bake in 14 minutes was taking 25. Food that should bake in 30 minutes was taking 50, etc. The big issue was that the exterior of the stove was getting extremely HOT when using the oven. The area behind the handle and the storage drawer were so hot I had to use a towel to open it w/o getting burned. Thought it was a faulty stove so I exchanged it for the same model. Just got the replacement and its worse than the 1st one! The heat permeates from the bottom of the door and heats up the storage drawer below. The area behind the handle and the enamel edge of the stove get so hot. Its definitely a safety hazard if not fire hazard. Anyone else experience this??? Its going back!

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.

Purchased a Whirlpool refrigerator less than 3 years ago, the inside is cracking in several places. I read someone elses review and they said the same thing happened to their refrigerator. Customer service would not do anything to help me.

The icemakers Whirlpool has been using for the last couple of years are a PITB. They have diamond shaped ice cubes which are great but, whenever the filter nears the end of its life, the icemaker fill tube freezes up. Occasional freezes up just because. Changing the filter, although the old one supposedly has some life left, may/may not solve the problem. Filling the ice tray with foreign ice for a few days thaws the fill tube and it will generally start up again - maybe. Complete waste of time and energy!

Yesterday I purchased this Whirlpool top load washer model WTW4816FW with agitator and we installed it at our vacation home and I started a small load to wash. Yikes, it made noises like a machine that is on its last legs. I knew from washing clothes for 40 years that this is NOT right. We, hubby and I waited and listened to this piece of junk to finish the cycle. Thank god I had set it for a short wash. We also videoed this contraption while it was grinding. I called Lowes and politely told them I was returning it. Thankfully they never had a problem with us bringing it back. (This must happen often.) I go back to the appliance department and decide on a Maytag. I noticed that it looked like the junk we just returned. I stood there and looked up the model number online and lo and behold there was a video of it doing exactly the same noise. It was virtually the same machine I just returned with just a name change. Needless to say we left the store washerless until I can research this further. I then found out that Whirlpool now owns Maytag. Thing is I just bought a front loader Maytag for my main home and it works good. It was a replacement for a Whirlpool without a agitator which worked well too. The YouTube videos seem to be washers with agitators doing this. I just wish I could post the video for all to hear. I guess we are all at the mercy of big companies who dont care if they make a good product as long as they can make it cheap.

Bought this Whirlpool washer (WTW5000DW0) to save energy and water consumption. It has been awful from day 1. Clothes come out with detergent (white marks) all over them. Clothes aren’t spun out enough to dry them. It takes FOREVER for a load to finish, I can’t imagine that this is saving me anything on electric. Waste of money. Do not buy this!

I have a portable dishwasher. It does not dry the dishes when cycle is completed. I have to either leave the door open or take them out and towel dry them.

Piece of crap. We built home 2 years ago and have all gold series appliances! They are all CRAP. Wish we would’ve upgraded to KitchenAid. Dishwasher won’t wash, microwave has hot spots and has to be unplugged and plugged back in often to work. Freezer side of the refrigerator will stop making ice because it freezes up often! NEVER buy Whirlpool!

Its now Nov 8 and Ive been officially dealing with this issue since Sept 26. This washer was installed in a new home. After less than 10 loads, my washer stopped draining and I was left with a load of towel soup for over a week while waiting for a service call. I still have the same defective non functioning washer sitting in my home and have been unable to do laundry at home in all that time. So far Ive spoken with 2 customer service representatives. The first was incapable of scheduling a service call. She clearly did not understand how to operate the database used for scheduling. I was finally able to schedule appointment on my own but had to wait a week before the technician was able to come by. It was determined that either the latch mechanism or the mother board or both are defective from the factory.The second was just plain dismissive and completely unhelpful. I sat on hold for about an hour each time before getting to speak to a person. Ive also received two canned emails in response to my poor review of this washer on the Whirlpool website. They basically blame COVID for the delays and state the parts delivery should take 3-4 weeks. I was originally told 14 working days for delivery of the parts. We are already past both deadline with no end in sight. At this point, Id like the defective washer replaced rather than repaired. And for the record, this was a new washer (less that one month old) installed in a new house that now stinks to high heaven because slimy, scummy water that will not drain out has been there since September 26. Id really just like for someone at Whirlpool to honestly care about this and take a moment to address this issue.

Purchased Whirlpool Gold appliances for a kitchen reno two years ago. Fridge and stove from a dealer and microwave from Lowes. Fridge - After one year the ice maker quit. $200 part plus labour. Seal on fridge door not sealing. New hinge and washers to adjust. $30 plus labour. Stove - three different stoves were delivered with the same paint flaw on the top of the control panel (3 inch section where paint did not adhere or was scraped off... Same spot on all three... clearly a factory issue). Stove door - when you touch it the interior light goes on. Warming button and switch was broken when purchased but didnt notice. Whirlpool wont warranty. $48 plus labour. Last piece in this puzzle... Microwave - magnetron went and wont heat. $300 plus labour. Obviously time to change brands. Now to figure out who is NOT under the same manufacturing umbrella.

We installed this furnace along with a matching 4ton a/c unit over four years ago. It was installed with a 3 zone computer controlled damper system to separately condition the three floors of our home. This furnace was ideal because it has a dual stage combustion chamber depending on how much demand there is. So besides being 95% efficient, the furnace can run at 70% or 100% heating capacity which saves on utility bills when the whole house doesn't need heat at the same time. It also had a variable speed blower which made start ups and shut downs almost unnoticeable. The blower actually ramps up to speed discreetly and adjusts itself according to the amount of back-pressure it senses. This allows it to respond to varying conditions as each of the 3 thermostats are calling for heating or cooling at different times. And yes here in St. Louis we have had days that require heat on the first floor and a/c on the third floor at the same time. The controller cycles between the two every 15 mintutes. All of these features make it ideal for our 2200sq ft three story brick home(four including the basement where it is installed). This furnace and control system along with new ductwork and dampers were able to replace the two old furnaces and a/c units originally in the home. We haven't had a single problem with it in over four years and would recommend Whirlpool Gold products to anyone I know. If I ever had to do this again in another house I would do exactly the same thing with exactly the same products.

I purchased my refrigerator four years ago from Lowes. From the second year ice would form in the bottom of the freezer weekly. This past week it stopped working totally. I had to call a repairman. He advised me the parts he had to replace were outdated and Whirlpool had made changes to the my refrigerator model two years ago. No recall. Just cheap parts that caused the refrigerator to not defrost. $400 later all is well and I am broke. I wrote to Whirlpool and their response was, Oh well, there was never a recall so youre SOL.

Cabrio Whirlpool washer - I hate this washer. Had it for about 3 years now and it will not spin out and does not give a code. Called a service tech out and they cannot find anything wrong with it. The water goes out but will not spin. It sits on 20 minutes and does nothing. Will not buy another Whirlpool washer. Wanted a good washer and got a piece of junk. Will not recommend it to anyone else. Think Im going back to the old style.

We purchased the Whirlpool Cabrio washer a few months ago. When we wash the white cloths using the (white) setting and add bleach and the HE detergent, the washer does not clean the white cloths very good at all. Sometimes the white cloths come out looking worse than they did before they were put in the washer. We called the people at Whirlpool and they said there is nothing they can do as long as all the functions on the washer work the way they’re suppose to. I thought the function of the washer is to clean the clothes but, they say no, as long as everything on the washer is working. That is what their warranty covers.

The repairman said the shaft, which of course is one piece with the outer drum, is corroded. Really? Did we not expect water in our washing machine? The repair is $500. After reading all the bazillion complaints on this model (on the internet), I have decided not to repair the piece of junk!

We bought our Whirlpool Cabrio in 3/09 from Lowes for $1000. Like many of you, we thought we were purchasing a quality product that we would use for many years. I never thought my clothes were getting clean, but I thought it was just because I wanted to see them floating in water. Its been 3.2 years and now were plagued with the code F51. Whirlpool is definitely aware of the many problems with these machines. They are also, obviously, unconcerned about the problems we are experiencing. Whirlpool will never stand behind their products if they dont have to. Please go online and write reviews everywhere you can. If we warn people and cause Whirlpool to lose a few dollars, they just might decide to stop selling junk. I plan on starting with all the stores in my area.

We bought the Whirlpool top loader washer and the drum broke down and after several attempted fixes it was replaced by new one as we were being financed through a business. So here comes the new one - same exact washer. Not only did it not clean well (normal soiling) then it goes to ul which means not balanced... not because clothes arent but because the thing that balances - it went only after a yr!! It would also keep filling draining again to no drain leaving clothes SOPPING wet... So very disappointed to say the least. What a piece of junk this washer is!! Its going to the curb tonight and being replaced by GE - NO MORE WHIRLPOOL AGAIN !!

Another person with problems called this a giant Whirlpool paperweight and he is so right! I received delivery of a Cabrio WTW7800XW3 washer on December 17, 2011. I had an issue (stopped in the middle of the cycle and flashed the letter “F” on the control panel) with it on January 2nd. I called and scheduled service. I had unplugged the machine and a few days later I replugged it and it started to work, so I cancelled the service call. In March, the problem started again. It just adds a little bit of water and then stops. Since then I have had repairmen out 6 times with 8 new parts installed and the washer still doesnt work. Now, the control panel won’t work. Whirlpool refuses to replace the machine. The repairman says these are the worst machines (any of the ones that are top load and have a clear top) he has ever seen and that I should buy an extended warranty. He says the bearings in the tub wear out among other things. On one of the repair visits, the serviceman found a chewed up pair of baby pajama pants. The machine makes a really loud noise like a jet engine taking off whenever it spins and the clothes are not clean. Whirlpool says that the warranty does not cover replacement of a defective machine. I have since researched the machine and have discovered that there have been problems with this line of machine for years. So, why are they still selling them? I am hoping for a class action suit. The company should stand by their products. I will never purchase a Whirlpool (or any other brand manufactured by Whirlpool) product again. I have had the machine for 4 months and it has been usable for about 2 of them.

The salesperson was great but we are not happy with our washer. We already had it swapped out once because of white spots showing up on our clothes. The only thing they could think of was that the bleach I used wasnt rinsing out completely so it showed up on our clothes. Recently, I washed a table runner by itself and it had some red in it. Now there are red spots on a couple of items that I washed after the runner. My husband just now asked why there were red spots on a shirt that he wears all the time. I explained. Also, we have had some white spots on clothes and I could scratch it out without leaving a permanent mark. Were no longer using bleach and we use only liquid detergent and all of it is HE. So I dont understand the machine. I hate it.

Whirlpool refrigerator - I purchased $6950.93 in Whirlpool products in one day last year at HH GREGG in Lexington, Ky. The refrigerator was purchased on that day September 18, 2012 and my kitchen wasnt going to be ready until December, but I wanted all items bought for measurements (specs) for the new kitchen designer. HH GREGG delivered to my garage October 26, 2012 because they couldnt hold any longer, but when we purchased that day they promised to hold till December when my kitchen would be finished. I have Proof from the kitchen installers the day they finished, December 28, 2012, was the day the appliances were installed. Well here I sit typing this letter on January 7, 2014 and my Whirlpool refrigerator is as of right now is in need of a compressor while losing approx $1000.00 in purchased food. In other words, approximately $900.00 in repair cost. Isnt Whirlpool a large enough company to stand behind its products when I paid $2599.00 for this refrigerator for at least one year from installation instead of purchase date? My fiancee has been trying to work out a solution with Whirlpool and the parts are on back order now. For at least two weeks we have been without a refrigerator and have two young children. Doesnt it show that the parts being on back order from Whirlpool, barely being a year old prove the defective product is being sold to the public daily? I plan on going further with this action due to the name Whirlpool all over my kitchen which disgusts me. Im going to write every columnist I can and do all I can with what little resources I have against this large company if no one helps us. This is absolutely an injustice against consumers...

If you are in the market for a new refrigerator, STAY AWAY from Whirlpool Top Freezer models. Mine just failed after only 5 years and Whirlpool will NOT do a thing about it, except ask, Did you buy the extended warranty? The compressor in my refrig was made in Mexico by a company called Embraco. I used to work for Whirlpool and these compressors were garbage then, and I guess still are, in my opinion.The 5 year sealed system warranty was removed from these refrig years ago and I can only assume this is why. If you want the 5 year SS warranty, buy a side by side or French door model. Just be sure it doesnt have an Embraco compressor on it! And while I am not a believer in them, planned obsolescence dictates you probably should buy the extended warranty/service plan for such a purchase. Dont rely on positive past experience, even for a company like Whirlpool. Their gold ring of promise emblem is very tarnished for me now.

Problematic... constantly out of balance... and will Not spin out due to this.. Sensors are very sensitive... have to unload and reload.. Most times have to wring out by hand.. Definitely a defect of these machines.

I have purchased 2 Ikea/Whirlpool ovens in 2011 from Ikea in Canada. I have used the self clean feature on both ovens and both ovens quit completely and the doors stayed locked. This problem is discussed hundreds of times on the internet for Whirlpool, Ikea and Kitchen Aid ovens. Since they are all made by Whirlpool they are all very similar or exactly the same in some cases, as is the problem. I have discussed this with Ikea and they have said they didnt know about the problem but would help to get it fixed to my satisfaction. I have had Whirlpool authorized service repair both ovens but after trying the self clean feature again, same problem.During one of my conversations with an Ikea representative on the phone, she contacted Whirlpool and was told that if the oven was repaired 3 times and deemed by the service technician as unrepairable, Whirlpool would do a buyback. In other words according to Ikea, Whirlpool would take the oven and pay me what I paid for the oven. Well after contacting the authorized service dept (not Whirlpool itself) for the third time, they did some investigation with Whirlpool about the problem. To his and my amazement, Whirlpool has come up with a fix as of October 2013. The technician ordered the new kit and installed it in both ovens. I have since tried the self clean in one oven and this time it worked. For the information of others, Whirlpool has the kit and in it is an instruction sheet with pictures as to how to replace and install all the parts in the kit.I watched the installation, quite a process. From the instruction sheet there is a number on it. Here is the number - w10625529 rev. A 10/13. This is an instruction sheet for Ikea TOD (thermal overload device) service kit. I have looked at many of the service parts diagrams on the internet for many different current models of Ikea, Whirlpool and Kitchen Aid ovens and in most cases almost all the inside parts are the same or very very similar which leads me to the conclusion that this service kit may work in most of these ovens to correct the same problem, but I suggest checking with the appropriate service people before taking my word for it. My observation is that the kit moves the TOD off the top of the metal plate of the oven and onto a new bracket which the tech thought it was to get it further away from heat (this Im not sure of since Im not an expert). He also suggested that this kit may also be designed to allow more air flow around the oven.My only concern after having the self clean feature finally work is the heat produced inside the kitchen cabinet in which the oven is installed. Approximately an hour and a half after turning the self clean on, I felt the side of the cabinet between it and the fridge (open space), and at one area of the wood cabinet I could not hold my hand on the cabinet as it was too very hot. I will be checking the inside of the cabinet for signs of excess heat and if I see any evidence, I will again call the service people. Since the elements were not on when I checked this, I assume the self clean had finished the heat cycle and was in the process of cooling down. When I test the other oven, I will make sure the elements are still on as I can see them thru the glass door. When I checked the temperature of the outside wood cabinet using a laser thermometer, the outside wood registered 64 degrees C or 142 F approximately. Not sure what the inside temperature was as the oven was still in place. Hopefully I will not get a higher reading when the self clean is at its maximum temperature in the cleaning cycle. Will the oven create any problems in the future for the cabinet, I hope not but time will tell. For clarification, the cabinets were built by a kitchen cabinet company using the instruction sheet that came with the ovens. I hope some of this will be of help to some of the hundreds of people who have posted this very same problem on the internet. When you have paid for an appliance you wanted because of the features it came with, it should provide you with what you paid for and not constantly break down. Im lucky as they came with a 5-year warranty so it hasnt cost me anything yet and hopefully wont in the future. Good luck to all in getting this resolved for all of you.

I purchased the Cabrio washer about 2 years ago. This summer, I began to hear a roar in my washer when it was spinning. I called a repairman and in order to fix it, the tub has to be replaced and it will cost $258 plus service call. My sister purchased her Cabrio 3 years ago and her washer has the same problem. This sounds like a recall issue to me. I think Whirlpool needs to recall this washer or pay my bill.

We have had the same problem with the magnetron in our Whirlpool Microwave Hood Combination. Replaced this part in Dec. 2012 after warranty expired. Cost of repair was nearly cost of microwave. Magnetron went out a second time this week. When I called Whirlpool customer service, the management rep was very hard line about the warranty on the unit and parts. Very clear this company has a product reliability issue and does not want to keep its customers. I dont plan to purchase another Whirlpool product ever. What a frustrating disappointment!

I bought a Whirlpool refrigerator (dbl dr) from Home Depot and received it on August 4th. When I went to clean it I found that blood had spilled from a roast and had accumulated all around the inside of the plastic shelf seal. It was impossible to clean. Water just ran inside the seal and diluted the blood. Then, it leaked all over my kitchen. I had a serviceman here for another problem, sent by Whirlpool. He said hed try to get them to replace the shelf. Never heard from him again. I called Whirlpool today. Was told I could buy another shelf. Otherwise, they didnt care. Said it wasnt a functional problem. This is a definite health hazard. Whirlpool used to be wonderful. What happened? I have a dryer, washer, and water tank about to need replacing. Whirlpool wont see a dime from me. (Home Depot, either.) This has become a very bad company. Ive contacted the NY Dist. Attys office. Meanwhile, I have a fridge with a major shelf missing for the holidays and for the foreseeable future.

Recently bought and had a Whirlpool Cabrio Washer (from Orvilles appliances) installed in my home. The very first day I hated it. Worst purchase I have ever made. I spent over an hour picking hair out of my clothes, and hair was also stuck in the crevices of the drum. This is the very worst machine and company I ever had to deal with. They told me, Too bad. Since there was no mechanical problem there is nothing they will do. I will never deal with either of these companies again. I cant wait to see what the hair build up will do to the machine itself, Had it less than a week.

On 11-29-2014 we were washing our laundry and our whirlpool washing machine started making a really loud noise so I went to investigate the problem. I open the bottom part of the washer to find out that the whole cement block to balance the drum was on the floor of the washer so I called the 1800 number on the machine and no one at whirlpool corporation wanted to even help. No one said sorry. No one said Let me see if I can help. No one. Every one I talked to they cant help at all. No one apologized once about the poor product that whirlpool sells and the defect that their products has. My washer is one year and one month old. So I can say truly with confidence that whirlpool product are the worst in the world plus their customer service even more. It is very sad after we paid all kind of money for our washer now I have to buy another one after one year and one month. Very bad customer service.

We purchased a higher end cabrio model only 3 years ago. Last year, on about every 5th cycle, the load would not spin at the end. Id have to remove all the wet clothes, set it to drain and spin, start it and wait for it to hopefully kick in. When I do it right, it kicks into the spin mode. I had to quickly press start/stop to unlock the hatch and reload the soaking wet clothes and wait for it to spin properly. Yesterday the same thing happened again. This time, it did not kick in. I ended up flipping the washer over and taking a look underneath. I discovered that the motor was seized. It had lost all its lubricating oil and smoked the belt. Now, my 3 year old washer is sitting in the driveway awaiting a trip to the dump since I got fed up and went out and purchased a new Samsung top loader. I emailed and called whirlpool with no luck. Not impressed. When I went out to buy a washer today the first thing I told the salesman was to stick anything with the name whirlpool out in the trash bin out back.

Four years ago, my wife and I also purchased a Whirlpool washer and dryer set, washer model no. WTW6600SB2. Within the first year we had to replace both pumps twice, user interface, and control board. (I think that’s what it was called). Of course, that was all covered under warranty. But I to had to wait a week for the part and then another week for the repairman to make it. The user interface and control board had to be replaced because moisture got into the control panel and caused corrosion on the circuit boards which caused them to short out. Then it wasn’t long after warranty ran out, the whole wash tub and drum just dropped to the floor with a full load in it. I don’t remember exactly what was the cause of it, but I do remember it cost me $580 to fix it. Then it wasnt more than two weeks later, the repairman had to come again and replace the control board again. There went another $600 for the parts, labor and service call because this time they had to come from 40 miles away and it’s a minimum fee of $89 just for them to drive up here and another $60 for diagnostics, and then the part and their time to install new board. I paid for this machine twice in the first year and a half. Then after all of that, it was finally working like it should and worked great for about 6 months, then came the UL,LD, and Lid Lock codes over and over unplug, plug in, unplug, plug in. That lasted for about a month, and then all of a sudden, it straightened out. And we only got the occasional UL code. Now in the last year, I have had to replace the drain pump twice and then the drum and motor dropped on the shaft allowing any loose change or other items if accidentally missed during pocket searches to fall into the outer wash tub and get sucked into the drain pump and causing a quarter to be shoot through the drain pump making a hole and caused my laundry room to flood. Well, I decided I wasn’t going to buy another part so I used a plastic repair kit to fix the hole and got it up and running. A week later, the washer won’t wash. It will fill and that’s it. So upon my own diagnostic, I came to the conclusion that it was the user interface that went out due to corrosion I found on it. So for another $120 I can fix it, but I’m not sticking another dime into the washer, nor will I ever buy another Whirlpool appliance. Once all of my Whirlpool appliances die, I will replace them one at a time with LG. I to contacted Whirlpool about my problems and all they did for me was send me an extended warranty offer for 50% off, really that’s it, that’s all I get is a big GFY after all the money I have stuck into this piece of scrap-metal. Well, never again will you have my business as long as I live. Whirlpool, you need to take your hoo-ya and do something about all of these complaints.

I have posted on here in the past about the problems with the Cabrio Washer from Whirlpool. Our third top load lid was just ordered since 2011. There is a design flaw where the plastic frame around the lid cracks and causes the lid to hump up. While shopping at a local appliance store recently, I saw a new Cabrio washer and the lid and hinge system has be re-designed. I wonder why?????

Whirlpool Duet Steam Front Loading Washer Model #WFW9750WW01 - The washer is only 5 years old and sounds like the space shuttle landing while in the spin cycle. Cost to repair parts only will be $896.87. The bearings among other parts are shot. I will NEVER own another Whirlpool appliance under any circumstance. Angry is putting it lightly!!!

I am completely dissatisfied with the Whirlpool Cabrio top loading machine. Our washing machine is less than one-year-old. It doesnt get the clothes clean, especially the darks, and it is so rough on the clothes that they come out twisted tied into knots. The dark clothes come out dirtier than they went into machine. Even though we use the dark detergent on the dark clothes and program for an extra rinse cycle, the clothes come out with white powder all over them. They need to be washed again and sometimes again. And sometimes they still dont come out clean. That is not very energy efficient. The clothes come out of the machine so wrinkled that everything needs to be ironed. I can imagine making washing machine that doesnt do its primary function, which is to get clothes clean. Todays families do not have time for this extra work.

I have a 2 year old Whirlpool refrigerator with french door refrigerator on top & freezer on the bottom. I am now spending almost $700 to have a new compressor put in because Whirlpool wont back their products.

I purchased an extended warranty with my product purchase and only a year and a half into using this brand washer the lid broke on one side at the hinge, it looked really rusty and like others I thought I was making a very decent purchase because all of my previous appliances were Whirlpool so figured Id keep up with the brand. Sad to say that was the worst decision I could have ever made for 13/1400 dollars for a washer with a light inside. Never again. They wouldnt even keep up the warranty because they said it was too expensive to repair it. Whirlpool is very bad for business...

My elderly parents had everything they own destroyed in Hurricane Sandy. After rebuilding their home, the new Whirlpool washing machine was broken. Whirlpool refused to disconnect and remove the machine that was obviously broken before it arrived. This is something that no one should have to go through. It is appalling and bad business. Through the kindness of friends, we had several male friends help with the removal. Truly shocking, that this is how Whirlpool handled this situation.

Whirlpool Cabrio washing machine: The washer was purchased in March of 2012 and malfunctioned in December 2014. After phoning Whirlpool, the machine was scheduled for repair with a factory-authorized company. The first repair attempt was unsuccessful due to a lack of parts. It took 10 days for the parts to arrive, and another unsuccessful repair attempt was made. The verdict is that a new motor control board, costing $350 plus labor, is necessary. With the delay in service and cost of repairs, I may as well buy a new machine.

We bought our house in December 2010 and the water heater (fg1f4034t3NOV) just started to give me fits. I had the same pilot light problems everyone else encountered. The person at the 877-251-1679 number gave me a good tip and that may have fixed the problem in the short-term. They told me theres a screen for venting on the bottom of the unit and to use a bottle brush after turning off the unit to clean the screen. I did this yesterday and the pilot light has stayed lit. I called the toll-free number and was told the water heater was out of warranty, but they could send me the part to fix the heater at half-price. I ordered it and they waived ground shipping. I hope to have the situation fixed soon. I’m very pleased with the level of service.

The refrigerator has worked OK except for occasional freezing towards the back. However the vegetable bins have both broken starting with various parts of the handles in front. We eventually replaced them. A brand new one arrive already broken. Same cheap brittle plastic. No alternative available. The company denies any problems or complaints about the bins. Feels like a small profit center for them.

I have a lower end 4 burner model but I love it. Both power burns are in the front (I would change that) and electronic ignition. The oven temp is true and heats up quickly, I bake upwards of 700 cookies at Christmas time. Even being a lower end model it works great and I use it everyday. I think it is more energy efficient than the model that I replaced, which I replaced in order to have the electronic ignition. I would recommend this Whirlpool Range!

My wife and I purchased this Cabrio washer 6 years ago when we got our new home. I have replaced the discharge pump 2 times, and approximately 2 months ago, we developed a noise so loud it was like a jet engine landing. I called our appliance store and paid $100 for an estimate, only to find out it will cost $973.00 to fix it. When we bought this, I was told it will be the last washer we will ever need. Ill never use Whirlpool again and recommend no one else does, either. I wrote to your customer chat line and basically the reply was Sorry about your luck. I know Im not the only one with this issue.

We bought this at Lowes. Initially, they got the color wrong. It took two trips to get the right color (white) then a third trip because all the parts were not there to install the dishwasher. After a few months the second shelf rail end caps fell apart. Now, after a couple of years the pump goes out. RUN from this manufacturer.

I just bought a house that has one of these ranges, and it was getting the F2 message. I found the problem. There is NO ventilation behind the electronic control so when the oven heats up, the control board gets too hot and throws the F2 code. That would indicate a bad temp sensor or bad board, but really its the heat shield on the back. Ive removed the metal plate from behind the control panel and it works fine now. Im considering drilling some vent holes and adding some insulation behind the control.

I am so unhappy with your product. Constantly have to restart machine. Never had a problem with my other washer. Takes forever to do laundry. Hate it.

Compared to others it gets the dishes clean and is easy enough to operate. Like everything else it has more bells and whistles than I want or use. Fill it up, put soap in and punch the desired settings and it does what it is programmed to do. Overall size seems to be like all the other models Ive used. Stainless with buttons on top of door. The top basket/drawer has latches that get tripped allowing the basket to drop down and confusing my wife. Not the best arrangement IMHO. Seems like the spacing of the supports in the bottom basket are off, but that may be due to our plates and bowls shapes.

Model WTW4850OXQO. Purchased this washer in Nov. 2011. Two months ago the washer began making a loud grinding noise in the wash cycle, so loud it can be heard throughout the house. Called the dealer whose serviceman said it was the gearbox and it would need to be replaced. Cost of the gearbox $235.00 plus $165.00 service. Called Whirlpool in TN and was told that I didnt purchase their 1 yr warranty. What the hell is a 1 year warranty but me paying Whirlpool to fix their defective piece of crap in case it breaks in the 1st year. I owned a Kenmore that lasted 11 years, an RCA that lasted 12 years, and a Maytag that lasted 10 years. Never a problem til they died of old age. This piece of ** is breaking down after 3 1/2 years. NEVER buy Whirlpool! Also, the inside of the machine SMELLS. My wife has to use bleach or cleanser to get the smell out. Once again a company in the USA thats too big to care about its customers!