Purchased our stainless steel Whirlpool Gold range hood microwave oven in January 2011. By August, there were problems. It was noisy. It would occasionally shut off for no apparent reason and eventually in August of that same year, it completely stopped heating. The magnetron was replaced at no charge because it was still under warranty. The microwave has continued to run very loudly, vibrate a lot and is still prone to random shutoffs. Now a little over 2 years later, it has now stopped heating again...I am assuming another bad magnetron. How is that possible? Our last microwave lasted for over 10 years! In fact we got rid of it when it was still working fine so we could get this one for over the range instead of on our countertop. So now I have a Whirlpool paper weight for which I originally paid $485. When I called Whirlpool, I was informed a service call would be $130.00 PLUS any necessary parts and labor costs OR I could purchase the repair plus 1-yr extended warranty for $289.95. Upon requesting to speak to a supervisor, I was informed that there were no flags in the system indicating any problems with this line of microwaves. I further inquired on how they are aware of problems... Essentially a phone call warrants little proof of any problem. A service tech would have to actually go out and witness that there is a problem for it to be noted. So, for those of us that simply decide to turn our back on the product and buy a new microwave, it would go undocumented by their company. My top-of-the-line microwave is less than 3 years old and has broken down again. Doesnt common sense tell you that there is a problem with the quality? I know Whirlpool has been around for 100+ years and I really want to like them, but if they dont support the consumers that purchased their products, I can no longer do the same for them.

The only thing cheaply made is the push latch on the dryer. Both are pricey for what you get, I thought, though they were the cheapest Lowes offered. We have had the pair for a little over a year. So far no real problems, though we really do not like the latch door. You have to slam the door to get it to close. To do it over we would probably have shopped a little longer and for the same money got a better deal.

I had to re-arrange my kitchen and have my slider doors moved over a foot to accommodate this monstrosity. After about 2 years the icemaker and water dispenser died - had to shove a facecloth in it to keep it from making noise. The white color is very hard to keep clean. Overall, I would not recommend a Whirlpool brand refrigerator.

I live in a new community, and this French Door refrigerator with bottom freezer was offered as an upgrade. Two of my neighbors and I have had the compressor break right after the refrigerator warranty expired. Luckily for us, the builder purchased and extended warranty, so we were all covered. I have NEVER had a compressor go out in ONE year.

I bought a new house in Hattiesburg with a Whirlpool dishwasher that is loud. It runs normally but when you open it the dishes are just as dirty as when you put them in if not worse since it will spray any residue from the bottom to the top shelf. I have taken it out and inspected all lines and such but can find nothing wrong to the naked eye. Thus I’ve got dirty dishes that must soak since the drying cycle retakes grime back on and then be rewashed.

Whirlpool Cabrio WTW8500DC0 - 2 months out of warranty, 14 months old. Motherboard fried. $300 if I do it myself. $550 to have it done. The unit was $780 on sale. Brand new piece of junk. Zero stars but thats not an option. Quite honestly, it doesnt clean very well and it doesnt rinse very well so we have to rinse twice to get the smell out if we use bleach. So whats the sense in buying a high efficiency washer? I work outdoors and weve had cheap washers in the past that clean much better and lasted many years.

I paid about $400 for this dishwasher and the regular price was over $600. Got a good deal. It washed dishes wonderfully. All I had to do was scrape the chunks off. It cleaned the rest. BUT... at a certain point, it started NOT cleaning. It was only about 6-7 months old. It was to the point where everything just came out kind of slimy and food grit was re-deposited on the dishes. I cleaned both filters. I made sure there was enough Rinse-Aid all the time. I ran hot water in the sink before starting to make sure the temp was hot enough. My husband went online and someone had instructions about cleaning the water intake because it could sometimes have sediment buildup. Not a difficult process, but there was no gunk in the intake filter. When I listened to a load it seemed like it drained, (most start with that), paused, rinsed for a couple minutes, paused, drained, paused and refilled for the wash cycle. So the pump worked, the arms went round and sprayed. Nothing was in the way of the arms. After it started the wash cycle, it seemed to just stall. It would spray for about a minute and then stop. Im not sure it sprayed after that. The timer kept counting down. It said dishes were clean, but it was an absolute waste of time. I was ready to go buy a cheap dishwasher and throw this one in the dumpster. I think it is a 720 padm??Just after my husband checked the water intake filter, we started another cycle. When it was rinsing, he opened it up and everything seemed to be working ok. It drained, then filled and started the washing cycle and then stopped. He opened it back up and surprise, the water was full on the front level by the float (that turns the water filling off). But in the back of the dishwasher, there was only about an 8th of an inch of water. Online it said the water should fill to just about the top of the heating element. It WASNT. Problem? It wasnt LEVEL. The instructions when installing said it should be leveled. We did when installing it (when it worked great). But looking back, we put in a new hardwood floor about the time it stopped working ok and we didnt put 2 and 2 together. We did not re-level. When we pushed the dishwasher back into its built in cabinet, it must have gotten OUT of level.The rinse part worked I guess. Then it drained and re-filled. After re-leveling the dishwasher, we opened the door at that point. The water was a level depth front to back and side to side. My husband explained what he thought had been the problem to me. When the wash cycle starts it fills, the float shuts off the water at the appropriate level. THEN... the dishwasher starts to pump and fill the arms and the tube up the back that feeds the upper washing arm. So much water goes into the arms and up that tube, the dishwasher looked almost empty of water again. As the dishwasher was now level, it began adding water to compensate for the arm/tube filling. Before the float would shut off too soon because the front part of the tub was full but the back wasnt. Without enough water, the dishes were NEVER going to/COULDNT get clean.The re-leveling made sure that the float didnt turn off the water filling until there was much more water, the CORRECT amount. The next load cycled all the way through, spraying much more than Id heard before and the dishes were clean. P.S. I also got some dishwasher cleaner and used that on a couple empty cycles. I NOW LOVE this dishwasher again. FYI If my husband wasnt handy Id have junked this thing. We HAD leveled the dishwasher when we installed it. Just didnt realize it COULD get un-level just pulling it in and out of the cabinet to install new floors. Check out all the troubleshooting stuff in the manual. But if it doesnt help, put a level inside across the bottom rack, front to back and side to side and make sure the bubble is in the middle of the two lines.The previous dishwasher I had, just made like a fountain of water that went up the middle of the dishwasher into a sort of funnel filling the upper arm. THIS one has that tube up the back and it curls down under the filter and Im guessing it is more sensitive to being OFF LEVEL, because the tube doesnt go straight down, it curls and lays across the bottom of the tub. Without being level, there was never enough water to suck up that tube to start the the actual wash cycle and it just stalled there till the timer said clean at the end. IE: dishes never did wash. BUT IT DOES NOW! Woohooooo!

Come with a new home. I dont like them. Piece of junks doesnt worth the money. I have them since a year now. Take too much water, dryer inefficient, consume too much energy. Every product from LG are good. The one coming from GE and sub cie as Whirlpool etc. are very cheap. The door are cheap, you feel the quality the first time you use them, very noisy, consume a lot of energy, broke after one years or less, you got leaks from the pump.

In June 2010 my wife and I bought a new Whirlpool water heater (model ee2h50rd045v). As I have fairly extensive experience in both the electrical and plumbing areas (was head lab technician for an aquatics lab for 7 years and worked with maintenance on a farm for 10 years), I installed the unit myself. Two months later the motherboard fried. Whirlpool sent me a replacement and all was fine. Six months after this the motherboard fried and set the unit on fire. Luckily I was home and caught it before it got out of hand and the circuit breaker had tripped when this happened (the circuit breaker saved the house).After I had ripped the smoldering unit out of the garage I immediately called Whirlpools Customer Hotline and told them what happened. They said they would send me replacement parts. I reminded them that the motherboard had fried once before and that this time the unit had almost cost me the house. I also informed them that I have now worked for Lowes for 4 years and I am responsible for selling their product (in addition to other brands). The lady stated all they could do was send me new parts and the problem probably was with my circuit breaker. I informed her the circuit breaker was tripped so the problem was not there. She reiterated that all they could do was send new parts.The next day I started to remove the control panel and motherboard to find that the plastic had fused itself to the frame and insulation. I called the customer hotline and spoke to someone new and informed them about the new problem with the melted plastic. I was told that the melted plastic could be scrapped off safely and that since the problem was not the circuit breaker, the problem must have been how the wires had been spliced from my conduit into the water heater. The gentleman then proceeded to tell me how to do it in violation of Maryland code and told me he would have replacement parts sent to me. I checked with a certified electrician to make sure my wire splice had been done in accordance with code and he verified I was correct.I then had a Department Manager call Whirlpool. He was given the same runaround and told the parts would be mailed to me. He was also given the story about how the malfunction was due to the wire splice being too tight. He then asked to speak to the representatives supervisor and she told him she would not transfer him over to her supervisor. I have forgotten to mention that 2 months prior to this, a Whirlpool water heater (same model) had been returned to my Lowes store within the 30-day purchase window. The unit had caught fire. Since I had had problems with my unit motherboard at this point, I took that unit apart to see what had caused it. The problem started with the motherboard in that unit also. This is unacceptable. Whirlpool obviously has product quality issues.Sometimes bad units are put out. This happens with every brand. But when the same model has such a high failure rate and is known to catch fire, Whirlpools actions are inexcusable. Currently my refrigerator, oven, dishwasher and obviously the water heater are Whirlpools. I will not replace either of these units with a Whirlpool when they reach the end of their operational periods. Also in the future when customers ask me about Whirlpool appliances, I will be sure to tell them just how great Whirlpool is, how reliable they are, how great their customer service is and then quickly usher them over to Samsung, Frigidaire and Electrolux appliances. The department manager that had called Whirlpool for me has shared similar sentiments about future customer recommendations.

Installed in May 2007, paid $674 for GU2455XTSS1 Whirlpool Dishwasher. It required service in March 2009 for $158 It became noisy in Oct 2011, so I placed a service call for $136. It was very noisy in Jan 2012. Again, I placed service call for an additional $93 that Whirlpool has not reimbursed. I must now replace the motor quoted at $403. The motor has a 90-day warranty. The 4.5 year old dishwasher must now be replaced. Whirlpool has not responded to email and to registered letter requesting a cost-effective solution to repair dishwasher that recognizes that reasonable life of the unit should be 10+ years and not 4.5 years.

We have a wtw5500xw2 washing machine we bought 03/2012. We can no longer use it. The machine would not spin or agitate so the clothes do not get clean or get the water out and after the cycle is done we have to wring them out after to be able to take them to the laundromat. So two repair companies and 3 months later we find out that it is the wiring harness that is the culprit. After a new motor and a shift actuator, we contacted Whirlpool only to be advised that the washing machine is out of warranty and that we are out of luck. If the company has a known issue about these wiring harness they should be looking into it and changing suppliers or offering to replace the wiring harness at a discount to its customers. I will not be buying a Whirlpool appliance ever again. I would recommend going with a Kenmore. I have had a Kenmore dryer that I got 19 yrs ago that we got used and only had to replace the heating element.

New stainless steel range 5.3 cu.ft. with convection oven delivered by Home Depot on time. Before the day was over the trim around oven glass was falling off. Double sided sticky tape was not holding. Yes its put on using double sided sticky tape. Called Home Depot, once you accept it, you deal with Whirlpool. They must first send someone to look and see. Yes its falling apart. Service tech will order new door. Mind you it will also have the sticky tape. We have also noticed that the glass top has many deep scratches, he will replace that also. A week later still no word, when. Used the oven because I couldnt wait and as it heated up smoke poured out of it and a loud noise from inside. Turned off and pulled out bottom drawer to unplug. Bottom panel had fallen down and undersides were rusted. Only had the stove 3 weeks and its Christmas Eve. Will read reviews first next time. No problems with my other Whirlpool appliances.

Multiple issues with the Gold Series. Have lost two refrigerators full of food!!! First problem was ice on the back wall of the fridge. 2 years later refrigerator is not blowing cold air and it is only 4 years old!!! Terrible product!!

I purchased my Cabrio washer and dryer 2 1/2 years ago, and for the past 6 months, I have dealt with it being unbalanced and I tried everything to get it balanced. When I researched the problems, I found so many other consumers are having the same problems and that Whirlpool will do nothing about it. I decided to start a petition on Change website to try to force Whirlpool to stand behind their product and correct the problem, offer us a refund or another product, or even fix the darn thing. It is tough economic times, and we spent money to have something that was energy-efficient as well as a product that is supposed to carry a good name. I am a single mother with three children, and I dont have a $1000.00 to throw away after 2 years. This is shameful that we, the consumers, have to deal with this. Please go to the Change website and sign my petition. The more signatures I get, the more leverage we have to deal with Whirlpool. Lets pull together and show Whirlpool we will not stand for them robbing us of a quality product. Thank you so very much.

I purchased a refrigerator Model# WRF736SDAW12 on 8/9/14 and from day two, Ive had nothing but problems with the ice maker. We NEVER use crushed ice, but we get a lot of crushed along with cubed and crushed/shards of ice all over my fridge, hands and floor. My daughter (wearing her heels) already slipped and fell while walking past the fridge, not realizing that there was ice lying on the floor because my floor is light/multicolored, so we cant see the ice.After several calls, the repair person replaced all the components of the ice maker and the repair person was told (2/26/15) from the Whirlpool tech that we would just have to live with the problem because its normal and he was advised to tell me to get a larger glass. The repair person looked at my glass, seeing that it was already large, shook his head and said Whirlpool must want me to start using a bowl to catch all the ice. I couldnt believe it?! I bought this fridge expecting to receive ONLY cubed ice and yet I dont, so Im sure why they put that cubed feature on there when I cant utilize it. I only want a little ice, but the first thing that comes out is the crushed ice, and in order for me to receive more cubed ice, I have to fill up the entire cup that includes the crushed/shards of ice which floats to the top and ends up in my mouth. Thats the purpose of me selecting cubed, so I dont have to drink it!After the repair man left, I called customer service (2/26/15) and she told me that ice gets stuck in the chute?, so thats why I get crushed ice, but its normal she says. How is that normal? Please read all the reviews/complaints from both the Whirlpools and on Home Depots website for this model and you’ll see this is a problem, there is a flaw in the design.I cant believe a big company such as Whirlpool would treat me so poorly and brush me off like this. After the many posts I put on their Facebook page, they over and over say they will be in contact with me. I have yet to hear from them. I found another story on Pissed Consumer where a senior fell due to the ice falling all over the floor, so its not just me that it has happened to. Theyre putting people in a hazardous situation and they dont care.I have an autistic son who gets ice constantly, I can’t supervise his every move and I’m not able to keep up with his dropped ice nor can he remember to look down for it. I’m concerned that next time my daughter falls; she won’t be so lucky and could sprain or break something. How about my visitors? Do I worry about them suing me when they fall? I’m not so annoyed at the fact that I step on water with my dry socks or the 24/7 noise from the motor or the left door not shutting all the way than I am with the safety of my family.

Bought a whirlpool refrigerator in 2015, have had both handles replaced 3 times, the bottom pieces of the handles are made of plastic and they crack. We had to take them to a metal fabricator and have them replaced with metal to keep them from breaking. Lowes and whirlpool know of this problem and they do nothing about it. Will not buy another whirlpool product. Very dissatisfied.

We bought this refrigerator because it was the only panel ready one we could find. When it was delivered the two doors did not line up. There was an adjustment that could be made but it required that Whirlpool had to do it. We made an appointment and was told it would cost $179 for the adjustment!! This for a refrigerator we had just purchased for several thousand dollars. The service person showed up and after working on the refrigerator he could not balance the doors. He blamed it on uneven floor, misaligned cabinets – anything he could say to shift the blame from Whirlpool. We called and complained again. They sent out another service person. He was just as useless as the first one. Told us to even out the doors we would need to shim the refrigerator which he would not do. Complained to Whirlpool with no results. Finally hired someone not affiliated with Whirlpool who was able to get the doors to be aligned. Never Never buy a Whirlpool/Kitchen Aid Appliance. They do not stand behind their products and do not care about their customers!!

We bought a Whirlpool 2 years ago. It is an upgrade for us. Has features of ice, light, temp, water fill. Other options, too many to list. Upper 2 door, pull out 3 drawer with freezer. Lots room. Very convenient. Would fit a family’s needs. Great for a handicapped person.

Model # WRF990SLAM00 Ser# K23919328 - It should be possible to rate this piece of junk zero stars!! Purchased on Feb 2013, it is driving me and my wife insane. It is noisy compressor wise all the time (Our kitchen and living room in the townhouse are one room). The problems started after the hurricane in 2016 killed our power for three days. I had to shut the refrigerator down to manually defrost the freezer section because the fan on the fan-coil was hitting a huge accumulation of ice. Then the weird blackouts started approx once per month where the panel light as well as the interior lights went on and off every minute with that dreadful BEEP. This went on for over 24 hrs and made living in the same room HELL. The beep and three clicks happen every minute and the cooling is none. Whirlpool service came ($80.00) just to look at it and will come back with the rest of the bill which probably will be astronomical. I feel cheated big time!! Minute and the cooling has worsened big time. Whirlpool service came ($ 80.00) just to look at it and stated it needs a new computer board as well as a new front panel on the left door.

Purchased Cabrio set last year. Worst set I have ever owned! Clothes do not come clean. Takes forever to wash. Must wash multiple times to get clothes clean, even on deep water settings. Does not spin water out of sheets and blankets. Dryer dries unevenly. Waiting on repairman because dryer will not come on.

These machines are designed to clean your clothes by rubbing them together which they attempt to do in a minute amount of water. They destroy the fabric, pull the seam out of shape, wrinkle them beyond the point of wearable, do not get them clean and do not get all the detergent out. I have had clothes come out partially dry. They also do not dilute the fabric softener, leaving unremovable stains on your clothes. In addition, they take forever to do a load of clothes even without the extra rinse you need if you want any hope of getting the clothes rinsed. The dryer is the slowest dryer I have ever had. The steam refresh that is supposed to get the hideous wrinkles out of your clothes does not put steam into the dryer. Instead, it sets the dryer to the highest heat so that those clothes you did not want on high heat are now getting it; then it shoots bursts, yes large bursts, of water on them. Your clothes come out a combination of still wrinkles and wet. If you hear of a class action suit, please contact me. These machines should be recalled.

Bought a higher end Gold Series French door refrigerator. Immediately the door would malfunction and the the piece that pops out to seal the gap between the 2 doors kept piping out when the door opened...They came out and replaced it which did nothing...The repairman said we have to open the door slowly...Give me a break...Have a older cheaper model that is almost the same and its always been flawless.Now in year 2...the whole system shuts down out of the blue and thaws everything then suddenly works for a few months...Repair guy says cant do anything if he doesnt see the problem...Just got back from long vacation...We turned off the ice maker and emptied...Returned home to damaged wood floors and a bin full of ice...System reset when it restarted and started making ice...2 years old and we have a Samsung on order and the Whirlpool is going in the trash...Weve had many whirlpool products and the defects are getting worse every year...Absolutely done with them!

Bought dishwasher and a gas range about a year ago. Had to call the repairman twice on our dishwasher and three times on our gas range. Now it is little over a year and I am out of warranty. I paid extra and thought I was buying products of a good brand. I should have bought products from one of the cheaper brands along with the extended warranty.

In 2007 our Whirlpool 30 gallon gas water heater began to have issues. Serial number 0425126675, Model Number FG1F3030T3NOV. The pilot light kept going out and would not stay lit.. After several times with replacement parts being sent with the same thing happening, finally in 2010 they replaced the water heater. A new water heater was professionally put in, serial number 1023T412357 Model number BFG1F3030T3noHV.I am having the exact same issue and I was told that the warranty was null and void on the new water heater because it was a replacement. They replaced a defective water heater with a defective water heater. I called the number given to me by Lowes 1/877/817/6750. I spoke with Nichole. I told her that I should not have to pay for replacement parts for a defective water heater. I told her that I was never informed that there would not be a warranty. I live on a fixed income and cannot afford to buy another water heater because I was given a defective water heater in replacement for a defective water heater. I became angry stating, Thanks for nothing and I hung up. So many people have the same problem with these water heaters that something MUST be done.

Had kitchen remodeled and purchased this microwave. Now after three years the door cracked in several places and now it will not heat food. Now we will have to replace this mess. Never buy any Whirlpool appliances again!

I purchases a Whirlpool 32 Cubic foot 3 door refrigerator in stainless model WRF992FIFM back on November 29, 2016 from Costco. I noticed that it was not making ice and that the refrigerator was around 50 degrees. This was on October 21, 2017. I called Costco and they contacted Whirlpool who sent out a service person on October 25. I am still without a working refrigerator and it is November 9, 2017 as I am told that a circuit board needs to be located.I have called both Costco and Whirlpool and no one seems to be worried about it. I was told by Whirlpool that if a part is not available by end of day Friday November 10 that I will be considered for a replacement. Considered really? I have never experienced such deplorable customer service on both Costco and Whirlpools part. It appears that this model is a lemon as there are large numbers of complaints on numerous websites. I asked for a refund due to the bad reviews and lack of parts and was denied. I will call on Friday for an update.

Whirlpool refrigerator Model type 14TFA seems to really keep things cold with good airflow in the freezer, and below shelves in bottom half are also keep cold adequately. Standard white appearance... somewhat boring.

Purchased a Whirlpool WTW7800XW a year and a half ago. The left top of the washers glass pops up, making it impossible to use the washer unless I weigh it down. Apparently a screw has popped out to hold the glass in place. Whirlpool used to make a decent product, but thought I should pay them $129 for their time, just to come out and then an additional part fee. How about the 30 minutes I spent on the phone with no satisfaction. My time is also valuable. I gave them the choice to come out and replace the screw (which shouldnt have fallen out in the first place) or lose a customer. Fortunately, I have a husband that can repair it, but I am extremely disappointed that Whirlpool is now making substandard products. We are a family of 3, so its not like Im doing laundry daily. Am I wrong to think I can get at least 3 years out of a product?

I bought a Whirlpool larder fridge 18 months ago. It suddenly stopped working so we got a service engineer up who said there was no gas. He said it would cost 50.00, but with no guarantee it would work afterwards.

My refrigerator is about 7 years old. Has performed great. Good use of room inside. Easy to clean. Bought only Whirlpool products for years however since the last purchase of a range a couple years ago the quality was greatly diminished. May be changing brands now.

There seemed to be an issue with the Whirlpool Cabrio Washer Pump. If a button comes off from your clothing or snap, etc., it gets trapped in the washer pump, causing it to crack and leak. Whirlpool on warranty only allows for one free change and anything after that costs $300.00. This is going to be the third time we are having problems with this and it is becoming, economically, a struggle for us. We have checked every button and snap to make sure they are fastened tightly, as well as any other type of items that may fall off in the wash and become trapped in the pump causing it to crack and leak. These pumps were poorly made and Whirlpool needs to be more aware of this problem rather than telling the customer that they are not aware of the situation.

Do not bother purchasing Whirlpool refrigerators. Bought mine new in November. The paint on the exterior has been chipping. They inform me that its a cosmetic issue and that they are not going to repair it. They told me to use touch up paint. The paint has chipped more than once and Im afraid this is going to be an ongoing issue. Its obviously a product defect (my last fridge lasted 27 years without incident). I dont do business with companies who dont stand behind the products they manufacture. These days its all about get their money and the hell with them once we do. Last time I purchase anything Whirlpool.

This refrigerator is a disaster. You will never be able to leave your home for any length of time for fear of a storm putting your electricity out which turns it off and if it DOES NOT TURN BACK ON WHEN THE POWER IS RESTORED. If you happen to be away for several days you will come back to a freezer that has defrosted all over your floor and your food in the refrigerator spoiled.

Lost two freezers of meat in this Whirlpool. Changed Motherboard twice. Wouldnt keep ice cream frozen. Tech told me I was buying cheap ice cream. Was told by Whirlpool that they dont replace freezers. Received a call from another WP rep who did replace it. Waiting 4 weeks now because trucking company wont come up my driveway in snow. It was here once out. Driver didnt know how to change unit out. Waiting for exp driver now.

We have had the Whirlpool Cabrio washer and dryer for 4 years now. Let me start off by saying the first 6 months was wonderful. Then after that, the machines were breaking down every time we turned around at the worst times. With 2 adults and 4 children, you see my point. We have had a repairman at our house to fix these machines 6 times and now, we are getting a code on our washer that is F1. Looking up codes online shows to be the computer system of the machine and a $400-$600 repair, might I add. Please save your money and buy a better and more dependable set than Whirlpool. Washers and dryers used to last 20-25 years, or so my parents and grandparents did. All of the manufacturers are building cheap junk so we can buy them more often.

I bought my Whirlpool Cabrio Washing Machine in 2010. I hate it 100%. I have never used bleach in the machine. I use liquid detergent only. 2 things happen every day: #1: When I wash a load of colors, I take them out when complete and there is dry white powder like substance over the black clothes. It looks dirty but it just got washed. #2 About once a week, I will pull something out of the washer and there is a bleach spot on it. The last item that this happened to was a $200 sweater. It went in the garbage. This should never of happened with an $800 washing machine.

I bought a Cabrio washer. Since we bought it, I have had to fix it. The machine is a piece of junk. It looks nice though. After 5 technicians later, our piece of junk is still having problems. We are a poor family with 3 kids who struggle to make ends meet. I feel that this company has taken advantage of the people who put their trust in the so called American company Whirlpool.

On 02/25/13 we purchased a Whirlpool Gold Series side by side (French door) refrigerator with an ice maker at the cost of $1,850.00. In April of 2014 the ice maker stopped working and the freezer at the bottom would not freeze food. Luckily for us it was still under warranty and was repaired. At the time of the repair, the repairman (associated with HHGregg) told us that the refrigerator should have been replaced since the cost of the repair was more than the fridge itself. Now July 20th, 2015, the same issue has surfaced. Again the ice maker will not work and the freezer wont freeze. I would not recommend this product or if you do pay the extended warranty.

Bought washer just under three years ago and the tub bearing started to sound like a jet airplane. Whirlpool seems to have an ongoing issue with the tub seal which goes bad and then allows water to enter the bearing which then fails. Whirlpool will not make it right, I guess I will have to plan on a $350 repair every two to three years if I keep this machine. I am very disappointed with whirlpool for not standing behind what is a known problem. They should replace these seals under warranty so that the Bearing does not fail. Thats my opinion, recall the seals and fix a bad design problem. I would not recommend ANY whirlpool products to anyone at this point. What other problems do they have with their other products?

Whirlpool oven aqua lift - This oven is the worst in the world. I cant even imagine cooking a turkey in it. After cooking a pizza it took four cleanings and a lot of scrubbing. Self cleaning --- not, you clean and clean and clean. I have had ovens that were not self cleaning and easier to clean than this. Do not buy. And Lowes is no help at all. Run as fast as you can.

I purchased a high-end Whirlpool dishwasher (WDT710PAYM) a few months ago thinking I was making a wise upgrade. Poor design and it wont dry dishes or properly wash utensils when theyre placed in the utensil rack on the door panel. The unit heavily condenses after using heat dry mode and large water droplets completely cover the top of the inside cabinet. Eventually, they all fall down into the dishes and you now have wet dishes again. The Whirlpool tech’s response was to scratch the cabinet plastic with a scratchy pad, smear rinse aid over the plastic cabinet and that should stop droplets from forming. Whirlpool’s customer service told me they shouldve never told me that and what I should do is be there during the drying cycle and open the cabinet door to let the steam out. This is completely ludicrous. Dont walk but run away from Whirlpool products.

We have had this washer for a little over three years. We are a family of 2 so it gets only light use. The agitator stopped working and the repair was going to be $370! The repair person suggested we contact the manufacturer but they refused to even pay a portion of the repair. Goodbye Whirlpool! And yes, it left white streaks on our clothes as well.

Don’t ever buy Whirlpool smaller (apartment) size front loader washer and dryer - from Home Depot or anywhere else. Beware of rules in warranty plans. I am very dissatisfied with them. I have had several service calls.

Purchased this Upright freezer model 160NZTQ02 approximately 2 years ago. Freezer had problems maintaining temperature from the beginning. Noticed it freezing up at air vents in back of interior. Unplugged, removed contents, and let defrost by ambient temperature (approximately 4 hours). After using this method for first three defrost periods (approximately two weeks apart) I began defrosted with hair dryer, then moved on to heat gun. Bottom line is this junk wont hold temperature and freezes up every few days to a week. No more Whirpool for me.

I bought my Whirlpool induction stove several years ago. We normally use a toaster oven for baking as we are only 2 in our home. Last year I decided to cook a large turkey for the family. I threw the turkey into the oven and started cooking it. After an hour or so I decided to start cooking the potatoes etc on the stovetop portion. My potatoes started cooking and my element shut down. I did everything I could to get it going but finally resorted to the manual to see if there was a suggestion. The suggestion was that the oven had heated the burners too high and that I had to shut off the burners and wait for 5 minutes and try again to use them. The oven was only cooking at 300F. I waited 15 mins to get it running again. The stovetop went out once again and I had to stop cooking. Conversely Ive had the same issue with the oven. Ive been cooking in the oven and have had it shut down as a way to address the stovetop being too hot. How am I suppose to cook on this unit with any kind of confidence? I did an online chat with a rep today and they suggested getting a technician over to the house. I was told I could pay $129 to have them look at it. This is obviously a design flaw that I was never told about prior to my purchase and would never have bought had I known. Shame on Whirlpool!

Purchased the fridge in 10/2014. 3 weeks later, condenser died and all our food spoiled. 1 year later, no more warranty, starter died, had it replaced for $280.00. Compressor died today 5/2019. Company refuse to do anything about it and will cost close to $1000 to replace compressor. Stay away from this company and their products.

This machine has had so many repairs that whirlpool should of replaced it. Now the machine is making a clicking sound when you turn it on to do a load of wash. It clicks for a few minutes then tries to sense whats in the machine then starts clicking again. Clothes come out of machine half wet. Queen sheets are dry in the middle. Water NEVER even touch the middle of the machine drum. All around nightmare with this machine. Would not buy another whirlpool because the customer service that I was given was terrible.

We have owned our side-by-side model # ED5HVEXVB02 for just over six years now. The first thing that went bad was the ice machine (just days out of warranty). Over the next 4 years weve had to replace 2 of the drawers; they break really easily. Here we are just 6 years out and we are on our 3rd icemaker. This refrigerator is a lemon. I sincerely believe they designed an inferior product so that they could get you hooked. We probably would have been better off after the first issue if we had sold this lemon instead of spending all of this money and future money that it will take to keep this product going.

Two days after the one year warranty ran out on our front load washer it started making a terrible noise. Of course the Whirlpool warranty was no longer in effect. The good news I was sold an extended warranty from Nebraska Furniture Mart. Called the Service Provider and was told they will only service the washer if it is not working. After several more calls they scheduled a service call in 10 days. We are a family of four, yes no washer is a problem. Finally the technician showed up and said the main bolt holding the drum assembly in place had broken off. He would have to order the bolt. It is now on backorder for 3 weeks. No washing machine for 4 people and now nearly a month is a pain. Not only did my calls to Whirlpool do nothing but the calls to the third party Warranty Company have been very frustrating. My call to the salesperson at NFM was very helpful, but didn’t help get our washer fixed. This is our second and last set of Whirlpool laundry pairs in less than four years.

My water heater burner went out after just over 3 years caused the pilot to go out. I was worried that although all parts were covered for 12 years and labor for only 3 and the labor would be very expensive. When I called and told them about the problem they said the part was covered and would ship it next day air but 10 minutes later another rep called and said they would cover the labor as well and to check a nearby service company as they might have the part in stock. Long story short without having to scream and yell my problem was corrected within 8 hours and all I have to do is drop off the new burner at the service company when it arrives. I have been lucky and haven't had many warranty problems in my life but none that I have had have been resolved so painlessly. I will never buy anything but Whirlpool from this day forward. Thank you Whirlpool.

In August 2011, I purchased and had installed a Whirlpool Wall Oven RBS305PVQ04 for $1000+. In July 2014, the oven failed with blown internal fuses and a thermostat $225+. In November 2014, the oven failed again, this time with a failed controller board. Whirlpool claims there are no replacement parts after just three years! In calling Whirlpool customer service for help, they basically said tough luck! NO parts, NO adjustments, NO service, you own a boat anchor. I tried to buy American; boy, was that a mistake. So it cost me $415 per year to own this LEMON. DO NOT DEAL WITH THE WHIRLPOOL COMPANY!

Doesnt clean unless you prewash (by hand). Top rack unstable, falls off runner easily. Level of liquid indicator on rinse aid container broke so I cant tell how much is in it. Main door spring doesnt work so that you cant open door halfway. It flops all the way open. Very ordinary features and I dont use the dry feature. Nothing to praise here. Size is adequate for my needs. However, the bottom section where plates go isnt well designed. Dishes dont fit well. You cant put the plates in a line but there are space left over on the side thats wasted. This is the worst dishwasher I ever had. They seem to get flimsier all the time.

Our Whirlpool refrigerator, model MODGI5FSAXVYO, began leaking water from the freezer onto the floor about 3 months ago. We purchased the unit in January 2011. We had to keep a towel on the floor to absorb the moisture. Our troubles began after the freezer door was left ajar and the interior became quite frosty. We had turned off the freezer several times to defrost but nothing helped until this morning when I read the comments of Marea of McClellanville, SC and Ruth of Vavenby, BC.I then decided to begin exploring taking apart everything until I reached the freezer unit in the back of the freezer. I discovered a lot of ice with the ice blocking the drain hole which is supposed to drain condensation from the freezer fins to a drain pan in back of the freezer. Apparently, leaving the freezer door ajar caused the drain hole and surrounding area to ice up. Condensation from the fins would keep dripping until it overflowed onto the bottom of the freezer until it filled up with ice. The water then had nowhere to go but out of the freezer onto the floor. The simple solution to this problem is to turn off the fridge, empty out the freezer and allow the frozen drain hole to thaw out. You can easily remove the back panel of the refrigerator to see if water is then draining into the drain pain. Good Luck! Ed

We bought this at Lowes. Initially, they got the color wrong. It took two trips to get the right color (white) then a third trip because all the parts were not there to install the dishwasher. After a few months the second shelf rail end caps fell apart. Now, after a couple of years the pump goes out. RUN from this manufacturer.

I am pleased with the steel tub, the ability to do an extra rinse and spin and especially the choices of water level that it determines by the size of the load. Its ability save water use. I would repurchase the top loader again. My clothes come out looking wonderful especially the whites and I do not use bleach. It does not get the mold or mildew odor that my last machine would get due to the rubber or plastic made tub. I love it.

I had my Whirlpool electric stove for about fifteen years, I have had a couple minor problems with it. The oven temperature sensor went out, I bought a new one online and replaced it. The stove top eyes get warped from uses. Really no big deal. Ive had good luck with it over the years. Its the standard 30 inch white. I paid over $400. It will probably last me another 15 years, I dont see why it wouldnt. But then I know how to fix appliances. I think the only reason why anyone would replace a stove is because of the color or it caught fire or wont come clean. The mechanical isnt a problem because you can rebuild them so easy.

We purchased a Whirlpool AccuBake oven in 2005. I think we used the self-cleaning feature about 3 times. The reason I mention this is it may be a possible cause to the frightening experience we had on August 15, 2012. My wife was cooking on the stove top when suddenly we heard loud electrical explosions coming from the back of the oven. We soon saw long arcing bolts of sparks shooting out the back, and my wife was terrified and didnt know what to do. I told her and my son to stay away from it. I ran to the circuit breaker box and turned off the breaker. We then looked in the back of the oven and it was on fire. I ran around looking for a fire extinguisher but my son managed to put the fire out. We called Whirlpool up and explained what had happened. They immediately sent someone out to look at it.I was very impressed at how fast they got someone out there. Whirlpool sent two technicians to look at the damage. After they were done inspecting, they told my wife that the problem is loose connections on Whirlpools side and not the feed and it had a damaged control board and that this is the fault of Whirlpool. He was very polite to us and apologized for any inconvenience. After a week had passed, no one called us, so my wife called and talked to some woman representative at Whirlpool. She told my wife that the report she got said that the oven had loose connection on the feed side from where we bought the oven and we should deal with them. My wife couldnt believe her ears and said, No, thats not what the technician told us, and the woman continued to talk and my wife said, Wait, slow down. The woman replied, Oh, am I going too fast for you? Well, I guess I have to talk slower then, in a sarcastic tone. My wife then called the technician who wrote the report and explained what the representative had told her, and his reply was, I cant believe she said that. I am not happy about this, that is not what I wrote in my report. Dont worry, I will personally take care of this. Again, the technician was civil and polite. After two days passed, my wife talked to the same woman again but this time she changed her story. She never apologized and said, It looks like in this report that the connections were loose to the control board. Since the oven is 7 years old and accounting for depreciation, Whirlpool is offering to you a total of $59. My wife said, Really, $59? How long is the life expectancy of these ovens? She told her, 10 years. My wife said, 10 years? Well, ours only lasted 7 and you are giving us $59 after we were almost killed and my home could have burnt down to the ground? She said, That is our offer.I called Whirlpool back and asked to talk with the safety supervisor and it was a woman again. Was it the same woman? It could have been the same woman my wife talked to, I was not sure. I asked her, When is it appropriate to issue a recall on a product? Our oven was defective at purchase. She said, You are the only complaint we had on this oven, so no recall is necessary. Yes, I said, but since it has been proven this is the fault of Whirlpool, I would expect at least a working oven from Whirlpool. I also told her the technician told my wife that Whirlpool should be bending over backwards for you, and she said, I apologize for the technicians remarks. I told her that I was dissatisfied and she will be hearing from me in the future. I did some looking on the internet and I found that KitchenAid which is made from Whirlpool had issues with a particular oven which was found that when the self-cleaning feature was used, it would heat up the control board, and since most people dont use the self-cleaning feature that often, it would take a very long time to develop. I thought that loose connections and heat are a bad recipe for disaster, and that quality control negligence and inferior components are to blame. Considering the past history and track record of class action lawsuits and appliance malfunctions such as the control board on their dishwashers, I believe it is all connected and related to my problem. Sorry but $59 isnt going to buy me a decent toaster oven, let alone a real oven. That oven should have lasted over 10 years and considering the possible damage and deaths that could have occurred, you would think that it would be in Whirlpools best interest to address this problem and bend over backwards for anyone who had the misfortune of purchasing this mickey-moused nightmare of a disaster-waiting-to-happen problem. Its not so much the money. What if a small child touches an oven as it conducts 220 volts then shocks into a childs heart to ground? What a ticking time bomb this oven is. As far as I am concerned, I dont want a dangerous oven like this in my home and Whirlpool needs to take some lessons in public relations.

Since these are made in Mexico as told me by the Lowes rep, quality has suffered. 1st one so crooked and put Roger on, no doubt a crooked floor, could not be fixed or leveled or plumbed. Got a replacement and, yes, same problem! Took off upper hinges and reamed all 4 hole out to line up tops of doors. Only problem is box of fridge is sooo racked that rear shims are needed, and many to experiment. My floor is perfect so its not that. Fixed for now but I am a pretty.much a perfectionist. Dont buy, make. Then Chuck them all in a landfill where they belong! And I dare anyone to try and get thru to them! THEY DONT CARE AT ALL!

The refrigerator has excellent quality, low noise level, clean lines and enough room for produce and frozen foods. Would recommend this to friends. This replaces a Whirlpool refrigerator that was over 30 years old. The original unit still works extremely well and we gave it to a family that needed a refrigerator and they were very happy to receive it. It looked as new as the day I purchased it 30 years ago.

I bought it 1 week 1/2 ago and cannot wash correctly the clothes in it, have to rewash 2 or 3 times and bedding? Forget it. Still is dirty. Water does not go over the clothes, it suck for the price I paid.

It works quite well except if you put items in the back of the top shelf of the refrigerator it will freeze them as if they were in the freezer section. I have a bottom freezer and that works quite well. And it is very quiet when running.

I purchased for over a thousand dollars a whirlpool propane hot water tank. Three months later the safety heat thing that turns it off is defective yet I have to pay for shipping on this. Then again every three months. Its been a year and a half and the damn thing just blew up and almost took my house with it. I paid for a product that works not one that needs replaced yearly. But do they care? Nope. 2 weeks before someone can even look at it. I plan on reviewing until whirlpool isnt purchased by anyone again. This is a brand that was supposed to be quality, instead its just a scam!

We bought a new Whirlpool gold gas stove. We had just finished redoing our complete kitchen, and thought it would be nice to replace appliances. I thought Whirlpool had a reputable name and good service record, but clearly, I should have checked. Three months after installing the stove, the handle pulled right off the door. We called the service tech who came in, took the door apart, and replaced the handle, but for some reason, installed different and incorrect screws for the door. Over the next 7 or 8 months, the handle pulled off twice more, and we repeated the cycle. At this point in time, we had been experiencing a situation where the stove would shut itself off. Bear in mind, it is less than 18 months old. Even now, the oven heats, and mid way through cooking anything, it decides to shut itself off. Clearly, there are issues with Whirlpool products, and when I called them, they want to do nothing about it. They jockey me around, from one service person to the next, frustrating me as I have to retell the issues to each new individual, and then they only tell me a replaced board, which would cost more than $600, is the way to go. Ive had this stove for 2 years, and it is seriously the biggest piece of garbage anyone ever put out on the market. Apparently there are no recalls on it, and so apparently, Whirlpool is more interested in ripping off their customers, than standing behind their product. I am currently seeking permission in a local paper to write a public service piece. I hope people will read it, and avoid this company at all costs. I hope whirlpool enjoys it. I dont know how they have turned a blind eye to all these complaints. As far as what I have read, with regards to other whirlpool problems, exploding glass, dangerous fumes, etc. They should be investigated, because what they are pulling off is criminal. If I want someone to steal from me, Ill leave my doors open, and let them come take me for what I have. I dont need to support a company that is stealing from me, while they wear smile on their face.

I am experiencing problems with keeping my pilot lit too. I checked the screen and this is not the issue. I have just returned from Lowes where I purchased the water heater and they informed me Whirlpool supplied kits for this issue and it was widespread. They mentioned a class action and went on to tell me they and all surrounding Lowes stores are out of the free kit and arent expecting anymore. Am I to feel lucky my water heater water didnt fail sooner only to feel unlucky all of the free repair kits are now gone? Lowes provided me with the Whirlpool phone number for help and they have just informed me it will cost me $35.44 plus shipping. I now see how widespread this problem is. This isnt right. I am very disappointed in the handling of this known problem! What is my next course of action?

I have been using Whirlpool products for quite sometime. I had bought a 3 door refrigerator (Protton) about 2 years back. However I am noticing that of late, the vegetable drawer does not cool to the appropriate temperature. The vegetables as a result are spoilt. I am unable to understand what to do. I have checked with the other temperature settings and they are all in the normal mode.

(Model WTW5640XW3) Whirlpool Cabrio worked Good for 11 months (just after warranty Expired). Replaced capacitor would not spin, hums loudly and smells like burning Plastic. Then about 2 months after that Lid locked, failed, replaced. 7 months then Actuator failed and now looks like the Main board give up. I dont know where The original parts are made but they are Cheap junk. New technology is crap for Washing machines, gears transmission and Solenoids last a lot longer plus they clean your clothes. And belts and solenoids.

Updated on 12/28/2020: I purchased a 28 cu. ft. side by side Whirlpool refrigerator less than 3 years ago (Feb. 18). The icemaker dispenser paddle quit working nearly a year ago and there are no replacement parts supported. Today the ice maker quit making ice. This is crap for a major appliance that youd expect to go twenty years or so. Very dissatisfied. Dont waste your money on this stuff.Original Review: I purchased a Whirlpool side by side refrigerator about 2-1/2 years ago, paid $1,800+ for it. Now two months ago the ice maker dispenser through the door quit working. I replaced the auger motor and that didnt help. Now the parts department says the actuator panels are no longer available. This is planned obsolescence to the Nth degree. No support for a major appliance less than 3 years old. Whirlpool SUCKS!!!

We bought this washer on 9/05/09. Recently, it sprung a leak due to a worn out seal that the repairman said would cost more to fix than just getting another washer. You would think this might be cause for distress, but I literally jumped in the air and clicked my heels with joy! This washer has been nothing but a pain. First of all, I have to pre-soak every load before washing or the clothes come out just as dirty as they went in. I would set the timer on my stove to let me know when the 40 min soak cycle ended so I could change it to wash. Then I reset the timer for another 40 minutes. I also learned the hard way, that using any kind of heavy duty setting would turn towels into a pile of yarn. This washer cost $998, and guilt is the only reason I didnt replace it years ago. Ding Dong the washer is DEAD!!!

I purchased this washers predecessor, the WTW6200 in May of 09, along with the matching dryer. The bearings gave out after 36 months of use, and our household comprises two adults in their mid-fifties. Estimated cost of the repair? $650! Why am I posting this here? Because two weeks ago, my daughter-in-law called to say that shed so liked my machine when she visited in 09 - Id had the thing for two weeks at that time - that shed bought the WTW8500B and... the bearings were already giving out. I suggested she get the thing repaired, sell it immediately and replace it with an LG product, which is what Ive done.She has been put on a three-month waiting list for the repair, confirming my feeling that Whirlpool, as a whole, has gone down the tubes. Their service record is dreadful, with an excess of 20K complaints existing at various consumer agencies regarding ALL the Cabrio line, and their warranty, Ive learned, is considered the worst in the industry. All in all, the single worst purchase of my fifty-odd years.

Worst service ever. This is my 4th refrigerator (I have 2 homes and moved a few times) and I have NEVER heard of a compressor going bad in 8 months. This was a new fridge, and all of my food went bad along with my infants milk. I cannot express how upset we were, and Whirlpool told us that they cant do anything for us, and it was just something that happens. Basically, they told me, Sorry for your loss... you should buy a longer warranty since this is not covered if it happens after a year. This is Whirlpools way of telling me, we dont care if you use our product. I am amazed that they wont give us even a credit for what happened. NEVER BUY WHIRLPOOL.

Strange bear like sound when it washes. We stopped it and on again, sound gone. Water on full water pump drain attitude ok. Big lid (grey) inside on. Ran some time water draining with tablets to make it clean and run better. Had someone to look for it, no sound. But when we now turned on, it sound like a mumbling high sound from inside machine or upper lid. We have some thermostat error a few times now. No hot water condition and no washing in high temperature. Håkon ** was the inspector of this strange thing happening. Could this be dangerous to let it run?

I purchased a Whirlpool 3-door refrigerator with the freezer on the bottom on 8/17/12. Within 4 days, the ice maker stopped working. It took two days for the repairman to come out and fix it. So all is well with that. Less than 2 weeks later, the refrigerator isnt cooling. Several days later, the repairman came and determined it was the evaporator fan motor and clutch. The parts were back-ordered for 10 days. Parts came in 2 more days before he can come out and install them. He realized they sent the wrong parts. Another week went by, then he came and replaced the fan motor, which is now making an ear-piercing buzzing sound. He came back a week later and said it needed a gasket, which is back-ordered. In the meantime, he put some stick on insulation around the unit. Not much help. Another week went by, and the gasket showed up. It is still making a high-pitched whining sound. He said it was the compressor. Whatever! I hate the refrigerator. The sound is one that just grates on your nerves and you can hear it in all the rooms surrounding the kitchen! A repairman has to deem it unrepairable before they will even consider replacing it. They consider it fixed. What about my bleeding ears! I just want it gone! I am so disappointed. I thought Whirlpool was a good product with a solid reputation. I have a $2300 noise maker! Is there a class action lawsuit?!

I have purchased all new Whirlpool appliances for our new home in March 2009. I have had trouble with the refrigerator door panel and will not switch between ice and water. Cost to replace over $100.00. Now its the range. When turning on the oven, my wife said she saw a flash of bright light and then I turned around and it was smoking up the house! I quickly pull the stove out and unplugged the stove. I then remove the back panel and found the right side of the control panel was burned. Had I not pulled the plug, a fire would have started. I have pictures to prove that! The cost to replace the control panel is $267.00 and that doesnt cover the repair man coming out to test if anything else is bad!

Something inside the machine broke causing it to tear up my clothes! I had it repaired once, now it is 4 months outside warranty and it is destroying my clothes again. Whirlpool will do nothing to help remedy my problem. They did offer to help repair it at a cost of $350. Not happy with my Whirlpool washer. Looking to replace my 16-month old washer.

We bought the Whirlpool refrigerator from Home Depot. The ice maker does not work. We get 2 cups of ice a day. Home Depot Told us we should get 8 to 10 pounds of ice a day. We call a repair service and they said we should get 2 pounds of ice a day. Still getting 2 cups a day. Call again and now they said we should get 64 cube of ice a day. So now Home Depot has us calling Whirlpool instead of them. Now we will have another repair company coming out. Waiting to see what they have to say.Very disappointed with Whirlpool for not backing their refrigerator. And don’t buy from Home Depot. You can’t return if you buy it. And I have a warranty on it and they have a lemon law 3 repair calls for the same thing and they will take it back. Not true. I will be calling once a week for 5 years until they get me some ice. They don’t deserve a 1 star.

Bought a water heater on May 5th for 539.00 and was unable to get hot water all the time. After many days and dealing with Lowes which did not help and Whirlpool, I discovered that the unit I bought had no dip tube to bring the cold water to the bottom to be heated and thus provide hot water to the hot water outlet on the heater to the rest of the house. People at Lowes had no dip tubes and really have no knowledge of what is going on as the people at Whirlpool whom I called.

I have bought a top load 6.2kg washing machine 3 months back. But now almost all the plastic parts are having a cracks. When I asked for replacement they said plastic parts are not covered in warranty.

I had this washer (WTW7990XGO) 5 years and finally had to replace it. It started with the touchscreen. No matter how often it was calibrated it was very frustrating to get it to respond. It would start dinging and going thru all the cycles at random times. Then there was the error code for the door lock. The door lock wasnt the problem, the surround was slightly warped and the door wasnt catching. Warped Im sure from having to literally climb into the machine to retrieve the clothes! Then a few months later it was another error code - the machine wasnt draining fast enough. It didnt drain at all. We had to use a water hose to drain it. After the second time with that, I went and bought a new washer - different brand, dials - no touch screen, and it has an agitator. Unfortunately, I ran into other customers in the appliance department who were having the same issues from 2 other brands of electronic washers. We all went back to as old school as was available.

I purchased a washer and dryer through Best Buy. I had already decided on what I wanted and have purchased Whirlpool appliances in the past including washers and dryers. I tried other brands and was disappointed so I wanted to go back to using Whirlpool w/d. I was encouraged to purchase this set because it was on sale. Worst mistake I ever made. I am so disappointed! I wish I could go back and do over. I would have gladly paid more for what I had wanted instead of saving (supposedly) a little money. I personally think they were trying to get rid of these models because they are awful and I have had so many problems doing a job I already dont but this set makes it worse. The washer is constantly off balance I think because you have to be so strict in how you lay in the laundry to the washer! Now the dryer takes even longer to dry my clothes than my twenty year old set (Maytag) which wasnt that bad. Is there any kind of trade-in I could do model: WTW4900B to get the set I really wanted (the models with glass top on washer and glass door on dryer)? I purchased this in April 19 of 2014. I hate it!

We purchased a Whirlpool Energy Smart Electric Hot Water Heater with a 12-year warranty from Lowes on August 30, 2010. The water heater stopped working and the green light was flashing three times. We contacted Whirlpool since it was less than two years old and they were very rude to us. They told us it was the sensors and we would have to change them out. We waited while they sent the sensors to us. We installed them and it still would not work. It continued to flash three times just as before. We contacted Lowes where we purchased it and they were extremely apologetic and said they would be glad to replace it if we could get an RA number from Whirlpool, but that many others have been having a hard time dealing with Whirlpool. We contacted the rude people at Whirlpool again. They said they were not surprised that the sensors did not fix it. We asked for an RA number so we could get a replacement (after all, it did have a 12-year warranty). Now we were days later with still no hot water. Now this rude technician said it was probably the control board. I asked him if we were going to have to be without hot water until we changed every part on the unit. At this point, we just took the hot water heater out, put it on the curb, and went and purchased a different brand. Whirlpool has lost us as customers for life. If their other products are as horrible as that hot water heater, I wouldnt take any if they paid me to. They were by far the rudest and most hateful people we have ever dealt with and life is too short to be treated that way. I predict they will be out of business in no time with the garbage they are putting out.

In July 2012 we purchased a new Whirlpool Gold refrigerator. Last month ice maker went out. We bought it at Best Buy. They sent out a third party repair co. subcontracted under Geek Squad. Response was same as all these threads - just have to replace it. Since Whirlpool does care why dont we all go after place we purchased these refrigerators or the suggestion of a class action suit works for us! This is absurd!

I purchased a Whirlpool refrigerator (model number GX5SHDXVQ02/K02778282) on 9/18/2010. It broke down in 1 year and 8 months; the circuit board control went completely out and ruined all my food. Whirlpool stated I was beyond the 1-year warranty and said there was nothing they would do, except sell me a 1-year warranty for $299. I was at their mercy, so I purchased the warranty for $299 and had the fridge fixed. I would like to be reimbursed at least for the $299 warranty charge. This company should be ashamed of manufacturing such a flimsy product and not standing behind the item to protect their name.

We bought the Whirlpool NU50T122-403 50 Gal water heater from Lowe’s and very disappointed that after 3 years it will cost more to repair it than replace it. The Whirlpool gas water heater and our Whirlpool refrigerator have been the worst purchases ever made. Whirlpool has been unreliable in our house and the repairs and downtime have been extraordinary. We have replaced with a Rheem from Home Depot.

BEWARE THE TEMP CAN BE 25 degrees off high and 25 deg lower and Whirlpool says that is within specifications. My oven temp was set at 350 and nothing was cooked... After 7 repair calls with their certified repair companies (the 2 worst repair companies that I have ever used) I was told that if you set your oven at 350 that if it stays in between 325 and 375 that Whirlpool claims that it is working fine and will not do anything. I called and talked to customer service and asked the lady that if you set your oven at 350 should it stay within a few degrees of that and she said YES.The people that work at Whirlpool do not even know what kind of junk that their company is selling. I asked to return it and get a more expensive model hoping that it would work better but they said that they sell ovens and do not buy them. Be sure to get in writing from your sales person that your oven will constantly hold the temp within a few degrees. I tried to do the Whirlpool survey but after 11 attempts they said that there was errors in receiving and they did not get it. If you buy Whirlpool then you did not ask the right questions. I WILL NEVER BUY Whirlpool again (unfortunately I have a Whirlpool dishwasher and refrigerator that are not much better) and if you do you will say the same things and be out Thousands like I am.

We have just built a new home and have spent a ton of money on appliances. I so wish I had looked up the reviews on this Whirlpool Cabrio Washer before we bought it. It makes a very loud annoying sound through at least a third of the cycle (which I was just told by Whirlpool is the normal agitating sound). We have also had to have service out here twice in the first few months because some of the clothes come out dirty in areas that were folded over because of lack of water even on the high water setting. It also, ripped my favorite white blouse right in half. Trust me DONT buy it, you will be sorry.

Worst appliance of any kind that I have ever used. Has only on/off button, in effect. Wastes water. There is no option to change anything once cycle has begun. No soaking. Occasionally, the machine simply decides to stop and drain itself so that you can start all over again!! No idea how long cycle is. Nearly done? No idea. No matter what temp or how much detergent or how much water, the clothes are not clean. The lid locks and so there is no way to know whats going on. I suspect there is very little water during rinse cycle. All of the whirlpool appliances are similarly horrible. Washer is the WORST. Shame on you Made in America.

Whirlpool Cabrio Platinum washing machine: You wont believe this until you call a parts replacement place for tiny part. The plastic (or vinyl) lid hinge bearings are located at hinge corners of lid. Hinge pin passes through them, one on each side. Half the size of a penny, UNCONSCIONABLE greed at the price of $32-$33 dollars EACH when ordered from a parts place. IMHO, design by INTENTIONAL failure to fail after three or four years. As a result, the lid will not stay up on its own. Then you find out the horrible news which is an insult to intelligence. Id have expected to pay maybe two or three dollars each, but NEVER the price they are demanding. Theyve got you and there is NOTHING you can do about it. At that rate, parts would run tens of thousands of dollars to replace the entire machine, part by part. These greedy clowns make car dealers look like reasonable people! The LAST Whirlpool machine of ANY kind we will EVER own!

I will never purchase from Whirlpool again. After 3 years of use in a 2 - person (adult) household, my Whirlpool Duet (WFW94HEXW2) washer suddenly stopped working with an F6 E2 error code. I unplugged / plugged in the machine, took off the top & checked connections, and let it sit overnight. I could not get it working. Speaking to a local repair technician via phone, he indicated it is likely the control board. Whirlpool changed that part from part number W10406632 to part number W10427967. Before spending the money on a service call, he suggested I contact Whirlpool to see if it is under recall. I contacted Whirlpools customer service. They told me the washer is not under recall but I may qualify to purchase their Repair + 1 service. When I expressed frustration at spending so much on a product that lasted only 3 years I was told This is not a known quality issue or recall. I will document a complaint for you. The chat session was then terminated by the customer service representative. We will spend over $300 to replace the part that Whirlpool obviously knows is flawed. However, I will not pay for an additional Whirlpool repair service to fix something that should not have broke in the first place. And Whirlpool (including Maytag, KitchenAid, Jenn - Air, etc.) will never get our business again.

We purchased the Whirlpool Duet (front loader) washer and dryer in 2005 from Best Buy. We had many problems with the washer leaking around the front door. After several visits, Best Buy (in 2007) said we could pick out a new washer. We picked out the Whirlpool Cabrio. About 2 years later the mother board had to be replaced on the Cabrio. We are constantly getting F codes and have to unplug the washer several times for it to reset. It also sounds like a plane getting ready to take off and from what I read that repair is very costly. It has been leaking as well. I contacted Whirlpool today and they informed me that there was no recall on the machine and when I told them that there were many complaints for the same issues online, they said they do not base their recalls on blogs and to fix the problem, I would have to incur the cost. This machine is the biggest piece of junk that I have ever owned. I will be sure not purchase a Whirlpool in the future!

Best stainless steel built dishwasher we could find in this price range. Well built with lots of room and easy access to both drawers. Easy to clean filters and a nice modern look.

I bought 2 Cabrio washing machines for my two homes along with the matching dryers. They worked for about 3 months, then the washers displayed OL Error during any wash cycle. I tried to contact manufacturer and have not been able to get service without charge. After reading the many posts I am not sure if I should dump both or start investing $$$ in service calls.

Our new home came with brand new appliances. I love our Whirlpool microwave. Its reliable, quick & has lots of great pre-programmed features to assist with regular. The independent timer is a total bonus too.

Purchased a new range from Lowes in November. It was delivered in January. Was told upon purchase that there was a one year warranty on the item. After using the item approximately three times, a piece of aluminum foil fell to bottom. It stuck to the bottom and removed some of the porcelain. Bacon grease had spilled into the middle of the oven which caused the oven to warp and also discolor the porcelain. They sent a tech out, who called Whirlpool. Whirlpool told them that it was cosmetic damage and only had a 30-day warranty! They also said I had to contact customer service again, which I did. Customer service said that the tech didnt do what he was told to do and that they would send someone out again. The same tech came out, called Whirlpool again, and was told there is nothing that can be done. I asked to speak to a supervisor because I was unsatisfied with this response. A two-month old oven shouldnt look like it is five years old. I never spoke to a supervisor. The rep just kept telling me that there was a 30-day warranty and that it was stated in my manual. After insisting that I speak with a supervisor, she placed me on hold. After a few minutes came back stating that she is sending my request to another department and that they will call me back in three to four days with their decision. I would not purchase another Whirlpool appliance even if they decide to replace this one, which I sincerely doubt that they will. VERY POOR CUSTOMER SERVICE!

After 2 years it stopped draining. We have to physically hit cancel to get it to drain. Also, I have had to make my own tool to take bottom spin bar off to get to and unjam grinder and we pre-wash all dishes.

I purchased my Whirlpool Duet washer about 14 months ago. After about 8 months, I noticed that it had started leaking. It was under warranty and the seal was replaced no problem. I then started to notice that my clothes were getting small tears in them. Around January (13 months after purchase), I got tired of finding new clothes and jackets with rips and tears in them. I finally found that the plastic piece around the entrance to the washer was rough and jagged. I called Whirlpool and they told me they could send out a service tech to file down the jagged edges. They told me this was a common problem caused by the zippers on jackets hitting the plastic and causing it to become rough. Because it was one month out of warranty, I would have to pay for the service call. The lady told me I could try filing it down myself. I feel like I should not have to file down anything 14 months after purchasing a new washer. I feel like I should not have to worry that my clothes are ruined every time I wash them. If this is a common problem as the lady told me, it appears to me to be a design flaw and should have a recall. I have lost several outfits and jackets due to this machine and I am very frustrated that Whirlpool would not stand behind their product.

We bought the Whirlpool Gold series side-by-side about 2 years ago with an ice maker in the door and with this design, the ice bucket is on the inside of the door, which we thought was a very clever design, taking up less freezer space. Well, to remove the ice bucket, we had to use a blow dryer because even though you press the button which is supposed to disengage the bucket from the door, it has always been frozen onto the base.Then we started having issues of water leaking from the ice maker. It turns out, that the lever that controls the chute was broken. We called a certified Whirlpool technician to come out to fix the ice maker dispenser lever. Well as it turns out, it cannot be fixed. It is a sealed in the door unit and to fix it, we have to replace the door, a repair estimate for door and labor is approximately $800. That is absurd.I contacted Whirlpool and was told that my refrigerator is out of warranty and that there is not an option to repair the dispenser. There is nothing we can do. I said that according to the repairman, we are not the first to report this problem. When I contacted Whirlpool I was told there is no recall for this item. We purchased the Whirlpool based on the reputation that it has had in the past and the good product we have in a Maytag (which is associated with Whirlpool) dishwasher. Well, never again are we going to purchase a Whirlpool or any of its subsidiaries products. I have read so many unhappy customers here that I cannot believe that Whirlpool continues to make such inferior products or designs.

If there had been a choice for no stars I would have given it none. I bought the Cabrio washer and dryer 2 years ago and been dissatisfied from the beginning. It was recommended to me by the repairman who gave me the bad news that my old Whirlpool was not repairable. I suspect that his recommendation came from the fact that it has a good record with regard to repairs and not that it did a good job cleaning clothes.I thought that perhaps there was a learning curve and I would figure it out. Not so. This washer leaves stains, sometimes even not getting something thoroughly wet. The washer does not get clothes clean, especially whites. I have replaced two sets of white towels because they were never entirely clean and eventually became so dingy that I donated them to the Humane Society. I tried using Oxy Clean and even bleach, but nothing works in this washer. Any workout or sports clothes I soak first in the sink because not doing so results in smelly cleaned laundry that has to be repeatedly washed to remove any sweat odors. The final straw came when I washed a small fleece dog pad and it came out of the washer with one third of it not ever having touched water. I tried explaining these issues to Whirlpool customer service agents, who blithely informed me that Whirlpool can do nothing to help. So, I will donate this heap of metal to anyone who is willing to take it on and never purchase another Whirlpool product. Incidentally, I submitted this review to the whirlpool review site and they refused to publish it.

In October 2009, we purchased a Whirlpool Cabrio topload washing machine for almost $900, because my wifes sister had a 1-year-old one and had been pleased. The Cabrio replaced a 3 1/2-year-old Maytag that died with a seized-up transmission. Maytag is also a Whirlpool product for those of you who do not know. We had issues at first with it going off balance but dealt with it. It was also taking 40+ minutes to do even a small load of laundry, but again, we dealt with it. Fast forward about 3 years, and we notice the machine is making really loud sounds during the spin cycle. I checked for any obvious issues but found none. The noise kept getting louder with each use. Finally, I called a repairman to check it out. His diagnosis was quick. The bearings were going bad in the machine, and he said it would eventually fail. He quoted me a price of between $400-$500 to repair because the job is very labor-intensive. I declined the repair but still had to pay him a trip charge. Then I checked with my wifes sister about hers, and she said hers had been making a very loud sound for several months but they were just ignoring it. I told her about the diagnosis of mine and advised her to tilt the machine back to look under it. Sure enough, there were oil stains under her machine, just like mine, indicating the bearings were failing. So we have 2 Cabrio machines, one 3 years old and the other 4 years old with the exact same problem. I called Whirlpool since I had registered the machine when I purchased it. They basically told me to go fly a kite since I had not purchased the extended warranty. They said I could attempt to repair it myself to save money, but they advised to have their repairman do the work. Well, no kidding. What a joke. They expect you to buy a $900 machine and have to replace it every 3 years. I am done with Whirlpool products. FYI, Kenmore products are also made by Whirlpool, so Sears is not an option. My wifes sister and we bought new GE washing machines, and both of us purchased the extended warranty this time. For $129 (5 years), its cheap, peace of mind. Whirlpool is crap. I would suggest never buying any of their products. I know we never will. Once they have your money, they dont care.

My son purchased a Whirlpool Cabrio washing machine about two years ago and now it doesnt work. It was an almost $1,000 machine. You would expect a higher quality product. I always bought Whirlpool products because they were so dependable so I recommended my son to go with Whirlpool. Big mistake, the panel lights up but when you press the power button, nothing happens. I do not recommend this machine to anyone. Im wondering if anyone else that has purchased this has had the same trouble.

We bought a gas Whirlpool Stove from Lowes. We noticed it was not heating like our last stove and thought maybe because it was new. No the stove does not heat properly at all. I cooked a pork loin for 40 minutes at 350 and it was still raw in the middle. I have had to cook everything on 375 which makes the door handles and knobs very hot. I called Lowes and they patched me into Whirlpool after a 45 minute wait. The rep from Whirlpool said, you can look at the manual and figure out how to calibrate it. No I cant. I have a warranty that is what it is suppose to cover. Then I was on hold for another 20 minutes. Really no one should tell you to read a manual to fix a gas stove. I will not buy another Whirlpool item. Poor customer service and that make you feel you are bothering them.