Microwave did not last one year and magnetometer blew up. Customer service would not honor request to help with purchase. Repair call was more than a new microwave. In essence, I would not purchase this manufacturers appliances.

The average life of a refrigerator is 11 years. We purchased a Whirlpool convertible refrigerator (Model EL7JWKLMS02, Serial # EWR1339731) on 6/12/04 from the Lowes here in Visalia, CA. The first delivered was DOA and Lowes delivered another. That should have been a warning sign. We have had several problems with the product, as early as 2006. All repairs went through Sierra Appliance & Franks Appliances.We are now in the market of another refrigerator to replace this one. We have had to have freon added now for the third time. Sierra Appliance was unable to find any leak, but each time, the freon was depleted. In addition to the health hazard of having freon leaking into the house, we have had the distinct displeasure of having to deal with food waste, etc. Because of the ongoing problems with this product, we are now facing the reality of purchasing another refrigerator to replace this Whirlpool product.Due to this, I feel it is difficult to consider another Whirlpool product and will question any product to ensure that it is not Whirlpool-related. If there is anything that Whirlpool or Lowes can do at this point, it would be appreciated. Thank you for reviewing this note of dissatisfaction. It appears that we will be shopping for a new refrigerator this weekend unless we hear from Whirlpool. In any event, I would like this recorded as a complaint from a former customer.

I purchased a Whirlpool over the range microwave (model WMH3205XVQ) on 9/27/10 and have replaced the door now for the second time due to the plastic cracking. I also discovered today that the plastic has again cracked on the vent grill and the control panel. The door, vent grill, and control panel were all replaced on 8/19/2011, under warranty. It appears to me that Whirlpool has a manufacturing defect which they need to address with the consumers who have purchased these products.

Certain brands of dishwashers made by Whirlpool, including Whirlpool, Kitchenaid and Kenmore, are a fire hazard. Most appeared to be made in the mid-00s. My Kenmore Elite, model# 665.16293400, bought in March 2006, started emitting a burning plastic smell. I removed the door panel and found where the control board wires have been overheating and melting the plastic liner inside the door.Further investigation led me to kitchenaidfire.com, which details the models involved and includes hundreds of reports of fires from these models. I also searched saferproducts.gov and also found over 100 reports of fires from these models. The report logs are growing rapidly as it appears most of the control boards start to malfunction about five years in.I called Sears and they said that Whirlpool needs to do a recall. I called Whirlpool and I was told that they do not make Kenmore dishwashers, only some parts. This is completely false. I couldnt believe the representative was told to tell me that besides the part that is failing is stamped Whirlpool. These Whirpool-made dishwashers are a documented fire hazard and need to be recalled. I do not know what it takes, hundreds of fire reports have been logged and they are rapidly growing, but I hope that it doesnt take someone to be killed before they are recalled.

I purchased this monster in 2012 and after six years of enduring not enough water to actually wash the clothes for years, now the bearings have gone out making it sound like a jet engine is in my family room when it spins. After researching the bearing issue, I find it will cost $250 to $300 to have them replaced. Its also a common problem in this model even when the washer isnt at all worn out and old. That combined with the fact that my clothes dont smell clean and some blankets come out not even wet at all, Im done. I wont ever buy a water efficient washer again. Churning the dirty underwear around with a few cups of water isnt acceptable. NOTE: The bearings left months after the extended warranty expired. Just like clockwork. I purchased a much cheaper - center agitator - washer with a deep water option available. It was half the price of this top of the line Whirlpool Cabrio Washer.

I love my Refrigerator. It is a side-by-side with ice-maker and water in the door. I have plenty of room in the refrigerator, and I really like the adjustable shelves. I would definitely purchase another Whirlpool (next time with freezer on the bottom). I love the Stainless and would probably purchase again - or depending on the kitchen maybe black.

I have had a Whirlpool washer for less than 1 year and have had it serviced over 7 times with drain problems - code A10 being displayed. Have not been able to resolve the problem with neither the dealer nor the manufacturer. What a lemon!

This machine is JUNK and in need of a recall!! DO NOT BUY!!! This was purchased at Lowes for nearly $800 a couple of years ago and what a waste of money. During the first year, they had to send out a tech that told me he was not familiar with top loaders and was not sure why the clothes were not getting clean, nor why they came out with a white residue on the dark clothes. We used the machine cleaner - which the cycles take nearly an hour (how is that efficient?), put in a load of dark clothes WITH NO SOAP and guess what? Then he had me dump in a gallon of vinegar to clean the tub and the wall of the washer and repeated the process and guess what? He informed me that it was just lint. Well, after several visits and using a suggested pin drop of soap, the problem remained. I finally asked him if he was so sure it was lint and not soap residue, would he be willing to taste the lint? It was soap.Obviously after an hour of washing in the efficient washer, the clothes are not getting rinsed. I know this because in just putting in less than ten dark t-shirts, they came out dry!!! He informed me that since he was a contractor for Whirlpool, he was not allowed to continue to come back as he resolved the problem that I was using too much soap! Well, that is only part of the problem. This piece of crap leaks. We not only have a water softener, but a household filter system. In just the last three months, we have replaced the hoses as they are corroding. We were informed by Lowes that the hoses that came with the washers were from China and that they have been replacing them with US made hoses to the customers at no charge due to the amount of returns. Well, those too have been corroding and now I once again have water on the floor.It cost $1.75 to take my clothes to the Laundromat, 26 minutes to wash and ten minutes to get there and back. That is what I have been doing, and using my 23 year old dryer when I get home. It is a shame that the company is not responding to an obvious problem. I only wash two loads in a week - not like I am beating the thing to death with numerous loads or heavy loads. I will not recommend, in fact, I BEG you not to spend your hard earned money on this junk. Buy a $200 washer and if it too craps out in three, four or five years... you are still ahead. You will even save money on headache medication and save your sanity.

Purchased a Gold Series Whirlpool dishwasher, Mo. No. WDT720PADW2, From Maruszcak in Schererville, In. on 1-29-16. Approximately a year later door was replaced by Whirlpool because of paint problem due to faulty design. Replaced door is now peeling and rusting by exhaust vent also. Contacted Whirlpool and they will do nothing more. They said it was a favor the first time they replaced the door. They feel this is a cosmetic problem! I paid a total of $675.03, Their repairman would charge a $100.00 to look at it and another $235.00 for a new door. I feel this is a design problem and they should replace it with a new model, a refund would be better. Very unlikey, because Whirlpool does not stand behind their products. The line also includes Maytag, Jenn-Air, Amana and Hot Point. Besides this I have found plastic pieces that have fallen off! I had to use plastic ties to keep them in place. Dishwasher does not clean well. Have to rinse everything first. Products are bad, stay away from them!

Purchased the 2015 Whirlpool Cabrio. Today 5-2018, the panel went completely out. When I called the store (Lowes) they asked if I purchased the warranty. I responded no, she went on to say, “Well since you choose not to purchase the warranty youre stuck”. Even if I paid for the warranty a washer should not break down in less than 3 years. My previous washer lasted 18 years with no problems. We purchased this washer because of the larger load. It was one of the most expensive washers. It’s a piece of junk and the manufacturer will not stand by their horrible product. Please DO NOT buy! I will be filing a formal complaint.

What a POS. Havent even used the thing to cook a meal yet and already some chunk of metal fell out from the port at the top left inside the oven (behind the vent). It was clearly cheap pot metal. What else is this thing made out of?

I replaced a 15 -year-old propane water heater with an electric on 02/01/14, due to the high propane prices, $6 a gallon, and because I felt the heater should be replaced. After installing the electric water heater I filled with water purged all the air out, powered it up, went thru diagnostics and heated water to 120. After an hour I turned on the hot water at the kitchen faucet, hot water was there but not for long, water got cold,.I troubleshot the problem back to the anti-scald valve installed 15 years ago when I had a professional install the first tank. By placing my hand on the hot water line coming out of the tank, I found the water was indeed hot before the anti-scald valve, after the valve the water was cold indicating to me the valve was not functioning properly. I went to Lowes bought the parts to bypass and removed the valve, went home and in another hour had the problem solved! I wondered why I had to turn the temp upon the old heater to get hot water! I am very happy with my electric water heater, not only did Lowes have the last one in stock, it was on sale $100 off regular price, it is a digital controller type with water temperature setting on the front. I checked the temp at the water faucet in the kitchen. I had it set to 120, the water temp out was 119.8 on my digital thermometer. Water was too hot so I lowered it to 110, perfect temp for a hot shower. Even if the thing uses more electric than it should I still save because the fact of propane is so high I couldnt see spending $600 for 28 days of propane, versus $400 on a new electric water heater. I would rather pay a higher electric bill than feel I am getting ripped off with the propane dealers! Also there is absolutely no residual heat loss. This is well insulated even comes with pipe insulation!

We purchased a Cabrio washer in August 2013, in early August 2014 we noticed that it was not getting all of the detergent out of the clothes (noticed it on the dark clothes after drying). We use less than the recommended amount of HE detergent and dilute it in the dispenser, also always use the extra rinse. We just had a Sears service man out at a $100 cost only to find out that he gets these calls all of the time and the machine is operating at the factory settings.After reporting the problem to Whirlpool all I got was we are sorry and a link to how to operate the washer. In the demonstration video it clearly shows that the water level never covers the clothes. I know Im old school but in my opinion the water should cover the clothes so it can properly wet and agitate the items in the washer. To say I am less than satisfied is a gross understatement. Im out the cost of the washer plus an additional $100 and after a year of ownership and contacting Whirlpool less than a week after the factory warranty ran out all I get is an Im sorry you do not know how to operate a washer.

I had the Whirlpool side by side GSC25C4EYW00 less than a year. The vegetable bin - 2nd from the bottom - front panel broke off. No wonder, there are 2 tabs holding it to the rest of the bin. Its cheap, brittle plastic. Come on, Whirlpool, you have to do better. What a disappointment. Dont buy one.

I purchased top load washer and dryer from Lowes last week. When I was washing clothes the first time 12/4/18 (the day Lowes delivered) I washed in quick wash setting, machine was showing me all stages of the wash on the progress lights. It took about one hour for one load. Today 12/11/18 I spoke to your customer service associates Trina regarding the issue with my top load washer wed4815ew1 serial m82572023. I was told a technician is schedule for repair tomorrow. I try to quick wash two loads, washer progress light only went to wash mode only. I had to press start/pause, select drain and spin to remove excess water. I started 8:30 am and finish around 1 pm. I was waiting for the cycle to finish, twice all progress stages light went blank. I have no idea when it will be done. Machine made noise, not spinning, no water in it. The dryer wtw4816fw2 serial c84621285, I dry at energy prefer setting, when the clothes was dry, dryer continue without the buzzing signal to stop. I had to keep watch of the time and turn it off manually so it not energy efficient when I have to monitor when clothes will be dry.

I bought my washer duet (model WFW94HEXL2) in Sept. 2011. Today is Jan. 2013 and it has been a year and four months since I got the washer. I decided not to buy an extended warranty. Its only my husband and I at the house so we take really good care of our appliances. The washer stopped working and is giving me a code F-6/E3/E1. Basically, I need to change the central control unit ($350), door latch ($120) and labor ($180), for a total of $656.13. Really? I paid $1,105.00 for the washer. Im really upset. I called Whirlpool and they said the item is out the warranty and there is nothing they can do. I am really upset.

Tried to do a small 2x3 bathroom rug and the spin was thrown off kilter. I have been doing laundry a long time and I know how to evenly distribute clothes etc so the washer should be able to handle it for the price I paid. The high end front loading Whirlpool set.

I purchased a refrigerator Model# WRF736SDAW12 on 8/9/14 and from day two, Ive had nothing but problems with the ice maker. We NEVER use crushed ice, but we get a lot of crushed along with cubed and crushed/shards of ice all over my fridge, hands and floor. My daughter (wearing her heels) already slipped and fell while walking past the fridge, not realizing that there was ice lying on the floor because my floor is light/multicolored, so we cant see the ice.After several calls, the repair person replaced all the components of the ice maker and the repair person was told (2/26/15) from the Whirlpool tech that we would just have to live with the problem because its normal and he was advised to tell me to get a larger glass. The repair person looked at my glass, seeing that it was already large, shook his head and said Whirlpool must want me to start using a bowl to catch all the ice. I couldnt believe it?! I bought this fridge expecting to receive ONLY cubed ice and yet I dont, so Im sure why they put that cubed feature on there when I cant utilize it. I only want a little ice, but the first thing that comes out is the crushed ice, and in order for me to receive more cubed ice, I have to fill up the entire cup that includes the crushed/shards of ice which floats to the top and ends up in my mouth. Thats the purpose of me selecting cubed, so I dont have to drink it!After the repair man left, I called customer service (2/26/15) and she told me that ice gets stuck in the chute?, so thats why I get crushed ice, but its normal she says. How is that normal? Please read all the reviews/complaints from both the Whirlpools and on Home Depots website for this model and you’ll see this is a problem, there is a flaw in the design.I cant believe a big company such as Whirlpool would treat me so poorly and brush me off like this. After the many posts I put on their Facebook page, they over and over say they will be in contact with me. I have yet to hear from them. I found another story on Pissed Consumer where a senior fell due to the ice falling all over the floor, so its not just me that it has happened to. Theyre putting people in a hazardous situation and they dont care.I have an autistic son who gets ice constantly, I can’t supervise his every move and I’m not able to keep up with his dropped ice nor can he remember to look down for it. I’m concerned that next time my daughter falls; she won’t be so lucky and could sprain or break something. How about my visitors? Do I worry about them suing me when they fall? I’m not so annoyed at the fact that I step on water with my dry socks or the 24/7 noise from the motor or the left door not shutting all the way than I am with the safety of my family.

We have had this dishwasher since 1983 and we still run it on an average of 6 days a week. Features are the fact that it has given all of our dishes, our silverware, our pots and pans sparkling clean looks for all those years. It fits nicely into the kitchen space which was designed for a dishwasher. It never needed a repair. After all those years, this machine still looks fine. After all those years I really doubt if it still has a warranty and it never needed service.

Without a doubt, the worst washing machine Ive ever owned. After 15 years, my trusty old Maytag finally quit, so we searched around and ended up purchasing the Whirlpool Cabrio Platinum 3 years ago. In that time, the hinge on the lid broke, and now it makes a deafening noise when spinning. We called a repairman and he said the bearings were bad and needed to be replaced... Total cost $275 plus $50 for fixing the lid. When we told the repairman that it was only 3 years old he couldnt believe it! We decided against fixing it because from the start it never got the clothes as clean as we were used to, and without the agitator post in the middle, which was a big selling point by the salesperson who sold it to us, the washer continually stops with an Uneven Load message. Large load, small load, it doesnt matter. You cant do a load of any size without the load becoming uneven. We are now searching for a new washer, and although I dont know what well buy, I can guarantee it wont be a Whirlpool.

I purchased a washer 6 months ago and it was starting by itself so I called to get a technician out and it took them 3 days to tell me that they did not service in our area. Long story short I was out of a washer for 2 weeks talking back & forth with Whirlpool which was absolutely a nightmare. Kept me on hold forever and hung up on me several times so they didnt have to deal with the situation. Absolutely no customer service at all. When it came down to it they were going to issue me a new washing machine and I had to go to the store to get it and when I got to the store they told me I had a $415.00 credit to spend. Thats less than what I had paid for the washing machine and then I am having to spend an extra $200.00 out of pocket to get another washing machine.My warning to you is not to purchase any Whirlpool appliances unless you want to go thru pure hell. These people do not care about anyone after the product is sold. Their customer service sucks, their appliances suck and Whirlpool just sucks all the way around!! Worst experience I have ever had and I hope they never sell another appliance again!!

We purchased a new side by side black finish refrigerator. There is a design flaw in the water/ice dispenser. The bottom of the dispenser has no edge so any drops of water run down the front of the refrigerator! This leaves constant watermarks down the front. 2. The finish scratches very, very easily. I would not recommend this finish to anyone with children or pets. When you open the door if your ring touches the surface it will scratch it! There was NO user manual on care and I used paper towels to clean. Big no no, as now I have fine scratches on the front. I would never buy this product again because of these flaws. I have a 7 month old refrigerator that looks 7 years old and it is just my husband and myself! Love the inside, hate the outside.

I have been having a problem when washing my jeans in the Whirlpool Cabrio that I have never had before with my old washer. When I wash my jeans, there are always a few pair, never the same ones, that have an odor like dirty dishrags on them. I always hang my jeans to dry so I do not think it is this. I have tried to add a freshener to the wash cycle, it does not work. I have tried to dry them in the dryer with a scented dryer sheet, it does not work. I am assuming after reading these past complaints from other consumers that it is not getting all of the clothes clean because of the lack of water. I always use the deep water cycle, but maybe it is not enough water as previously suggested. I have had an issue with blankets and other heavy items not getting clean and/or not even wet. Thoroughly disgusted with this appliance!! I love all of my Whirlpool kitchen appliances though!

This washing machine has not worked well from the time I bought it two years ago. It never fills to the amount of water required to clean clothes, it is always off balance, so I need to adjust the clothes at least five times per load. I end up wringing my load out by hand. The clothes come out smelly and not clean. After the cycle is done all the clothes smell like mildew. The other night while doing a load, it made such a loud noise in the motor and started to shake up and down, and then moved forward, like it was going to take off or explode. I tried to do another load, but after it filled and started to agitate, it started to make a loud grinding sound and there were 25 minutes left, then the timer showed 26 minutes left, like the computer in the machine is messed up. I had to empty the water out, wring out a load of clothes including towels, exhausting.The worst part is that the machine is finally paid off, I am a single mother on a disability and I am stuck with this piece of junk. I felt desperate so I looked up Cabrio washing machines to try to figure out what could be wrong, and then I find all these negative reviews, and these owners all have the same issues. Why has there not been a recall, or a class act, who can afford to replace a $700.00 washing machine every three years. I also purchased the Cabrio dryer which cost over $700.00. I do not trust that it will be any better in the long run.I cannot rate this machine as it has been a nightmare from the start. White socks seemed to come out with more dirt than when I put them in, and I am sick of using bleach all the time, the fumes make me feel ill. This is not acceptable, obviously this item is defective, and a prominent company such as Whirlpool should take the loss, not all the victims that paid too much in the first place trusting that Whirlpool was a reputable company, I will never give them my trust or business again. I hope to hear from you, and if there has been a recall or class act legal actions, please let me know as I want to be involved.

Hi team, I have to lodge this complaint after because of getting continuous problems I have suffered with my Whirlpool fully automatic washing machine top load 11 kg bloom wash 360 degree. I purchased the abovesaid brand new washing machine on 1st Jan 2017. Since the purchase I am struggling with this machine. I raised the fault in the beginning itself and the service was done on 5th of Feb. Jobs sheets enclosed here with.Similar issues kept on arising and whenever I raised those issues with the whirlpool team, they mentioned that company policy is to repair the faulty part if it’s in warranty and they will not replace. They suggested me to go for the AMC and to be on the safer side, I also took AMC under warranty period only. (AMC card - My cheque dates and service details all are mentioned onto it.) Recently I faced another issue on 26th Feb for which ticket was raised. Engineer visited on 27th Feb and advised us to replace the motor part. On 3rd March they replaced motor mechanism and ball-bearings. Then engineer advised us to check the working by giving a trial wash.I started the machine to wash clothes and after 20 mins machine started making abnormal noise. (I have made video of it, audio of the video captured the noise). I again called up the service engineer immediately and informed him about the voice coming out of machine and he gave a lame answer by saying “It is normal sound”. Then I again called Whirlpool and requested senior engineer visit to resolve the issue. Senior engineer visited and told us that one of motor screw wasn’t tighten properly. It opened while running the machine which completely damaged the motor.After that I am continuously calling to service centre to get the updates on my machine motor replacement. Finally they mentioned that they dont have motor part available with them due to company ceased this model productivity. When I raised this issue with the Whirlpool team they mentioned that they can only pay 40% of the machine value, because I had AMC. However, I did mention that this damage is caused by the negligence of their service engineer, but they didn’t discuss anything about it.When I continuously chased them they dropped me an email to refund only the 40% of the machine value. I feel cheated and harassed!! When I bought the machine they gave us 10 years warranty now they mention that motor is not available as it’s a 5 years old model. My grievance is that since I had already taken the AMC and the damage was also caused by their engineer, why I have to bear the loss. I have already struggled a lot with this machine since last 5 years from the day I bought this machine and now I am losing my hard earned money. Kindly do the needful. Documents attached as follows: 1. Serial number of this machine 2. Bill/ Invoice copy from dealer 3. Job sheets4. AMC card (with 3 years extended warranty) Thanks,Pratibha

Whirlpool dryer and washers have the worst reliability, plus terrible customer service. Parts missing from factory install to faulty parts that constantly need to be replaced. Wasting precious time to meet with service repair people. Not worth it. Make products that are reliable and be accountable.

We purchased a new home April 2013. All our appliances were new Whirlpool stainless. Looked nice. After almost a year our microwave started acting improperly. Beeping, changing screens, not working when buttons pushed. Then the micro wave had a melt down and caused the glass try to break, parts to melt and caught fire internally melting plastic. Notified Whirlpool and they sent out individuals to repair. After several weeks the repair was completed and we were advised that they did not understand why this would or could happen. We should be fine now. Well we are now again having this unit beeping, changing screens, not working when tried, and when entering numbers, number and time are not what was trying to be entered. This unit my wife says is possessed and she wont use it. She fears it will burn the house down. It is Velos model TR 2 24 11000 serial number. It now beeps and changes with door open as I read the serial number.

Whirlpool microwave oven a few months old stopped working. Customer service center not helpful with prolonged holds (>30 minutes), no response to email, and amazingly no response to live chat. The 800 number was busy at one point for over an hour. When I finally did get thru, there was no coordination with local repair men, and a factory delay on the parts. I am going on 6 weeks without a functioning microwave and 3 kids at home. Thanks Whirlpool.

I purchased the Whirlpool Cabrio (wtw6600sw2) about five years ago. Last year, the motherboard had to be replaced. This year, it started to have load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $75 to have someone look at it, and to fix it will cost almost $400, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. I called Whirlpool and my model does not have a recall, but models with same problems have been recalled. I will never buy a Whirlpool again!!!

When renovating my kitchen I went with all Whirlpool appliance. I have nothing but trouble with my fridge. About a year old we had to replace the motherboard at our expense. After having that done, about 6 months later I had to defrost it so it would work again. Now it has to be done every month. All they say we can book another service call at my expense again. All I say thank goodness I kept my old Frigidaire. It saved me more than once. So my advice is stay away from Whirlpool. They dont stand behind their products from my experience.

Bought a whirlpool refrigerator in 2015, have had both handles replaced 3 times, the bottom pieces of the handles are made of plastic and they crack. We had to take them to a metal fabricator and have them replaced with metal to keep them from breaking. Lowes and whirlpool know of this problem and they do nothing about it. Will not buy another whirlpool product. Very dissatisfied.

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.

We moved to a new home with all new Whirlpool appliances. We have been here 4 weeks and so far the stove has had a faulty part replaced in oven and now my microwave will not fully pop popcorn. Wonder what to expect next?? If you have a choice dont buy this brand. Inferior product.

I bought a Whirlpool Dryer after reading an excellent review in Consumer Reports, despite it costing more than I wanted to spend. The first thing I noticed was a thump, thump, thump with every rotation of the drum. Then I realized that it took twice as long to dry my laundry as my 45 yr. old GE dryer, which only needed a belt, but which wasnt available anymore. I was disappointed in the Whirlpools performance, but that was only the beginning. One night when the dryer was less than 3 months old, I was in bed for the night and I heard the familiar thump of the dryer running. I went downstairs and could not stop it as it did not respond to anything on the digital control panel. I finally unplugged it. I called Whirlpool and they sent a new control panel, but I had to pay the service man.Not too long after that, the dryer heated up, but the drum would not turn. The serviceman said that it had come off track and he reset it. Shortly after, the door would not stay closed as the clamp that held it shut had fallen inside when I pushed the door closed. I replaced that. Then the drum continued to come disengaged because it was out-of-round. But, of course, the dryer was out of the 90 day warranty period too and a drum replacement would have cost more than the piece of junk was worth. So, I had it put back on for what I told myself would be the last time. Well, it was the last because the control panel went bonkers again and would go on by itself and only ran on one cycle if I plugged it in and unplugged it when it was done. I finally gave up and bought an inexpensive analog GE dryer which I never had any trouble with and dried the clothes in less time with less noise.

I purchased a rental home with a Whirlpool hot water heater. In the home inspection, it was deemed to be in good working order. The first day the tenant moved in, I received 3 service calls for no hot water. My contractor told me I needed to replace the start up assembly and it needed to be ordered from Whirlpool directly, as it is not available in stores. When I contacted Whirlpool Customer Service, the operator, Stacey, was rude and unhelpful. She told me that the warranty was void because I was not the original owner, even though it does not state that the warranty is not transferable. She also told me she could not help me order a replacement part without the item number.

When I first bought this machine I loved the big tub, but I was concerned that there was no agitator. It confuses me how clothes can get clean if there is nothing to rub them again. Even in the olden days they rub clothes against a board. Well my concern is valid and I believe the washing machine industry needs to go back to the old model, as this new version does not work.Here are all the problems: 1) The machine judges how much water to put in. This doesnt work. I follow the directions and outline the perimeter and dont overload, yet still it just barely puts in enough water to make the clothes wet. Im all for conserving the environment, but enough water needs to be provided to actually get the clothes clean. I would like to be the judge of how much water should be used, so I would like to be able to tell the machine if it is a small, medium or large load. I do believe that the lack of enough water is why the clothes do not come out as clean as they should and why they end up smelling (see #4). 2) There is no agitator, so there is really nothing available to help clean the clothes. Spinning them around like a maniac is not enough, which leads me to the next problem. 3) The clothes come out twisted terribly and then many times come out of the dryer wrinkled because of how hard they were twisted. I tried to select a less harsh spin cycle, but then the clothes are too wet to put in the dryer. There is no happy medium.4) Biggest problem to date: Our clothes/towels have all started smelling. You know that smell when you leave your clothes in the washer too long (like two days) and then put them in the dryer? Its that smell. The clothes/towels dont smell when you immediately take them out, but they do smell at any bit of moisture. When I dry myself off after the shower, I notice the newly washed bath towel smells like a wet dog. I have used the pods, liquid detergent and powder. I dont remember having the smell problem when I first bought the machine and used powder, so I just returned to using powder today. (Ive even tried doubling up on the pods, but the clothes still smell.)This leads me to problem number 5: When using powder in this machine, the machine does not empty the powder container completely, and so the clothes do not get the required amount of detergent. Often there are clumps left over in the powder dispenser, but not always. (This is what led me to go to the pods and liquid detergent in the first place.) But at least with powder (I use Gain) my towels dont stink after the first time I used them.I wouldnt recommend this machine. I really researched machines before I purchased this one, but they all had bad reviews, so how do you pick? And I never look at the good reviews because we all know so many people are paid to rave about products they know nothing about, or it is a company employee writing the review. This machine is a huge disappointment. I am going to try adding a rinse cycle like a previous reviewer suggested. Maybe the extra water will help with the smell. Of course this is not good for the environment though, so this whole way of making washing machines with no agitator and limiting water defeats the energy efficient goal.

Bought Whirlpool refrigerator (Model # WRF560SEHZ00) December 2018. After 2.5 years, the door hinge failed and could not be replaced. $1,000 for new door. Dont buy! Too bad there wasnt a 0 option for the rating.

Ever since I purchased your washing machine, it has sounded like a diesel truck or cement mixer. You cant hear anything over the noise anywhere in the house.Have had two repairmen out to look at it and they say, Thats normal. I have a friend who has the same machine and it doesnt make noise like this one. I will never buy another Whirlpool product again and hope this blows up before the warranty expires. Also the tub is falling apart. What a piece of ** this machine is. You should be ashamed to put trash like that on the market.

Have used washer since 2005. Still runs today. Minor repairs done. Is reliable brand. Whirlpool gold model washer purchased at navy exchange. Will buy another whirlpool again. Have bought other brands which lasted 7yrs and then needed replacing. This whirlpool is the best. Lasted 15 yrs and still working fine doing 5 loads a week.

The beat goes on. My Cabrio washer is still down. After working for a mere 14 months, the control board died, and the machine would not spin out water. The repairman ordered a new one. Though the part arrived several days earlier than predicted, the repair service said they could not send anyone out, until our scheduled appointment. At last, today, the repairman arrived. I am ready to start whittling down the mountains of laundry we have stuffed in every closet. Some areas of my house are starting to smell like a locker room. It is not convenient for us to haul everything to a laundromat, or impose on a relative who lives nearby.The repairman was in the laundry room for at least 45 minutes, and then very apologetically tells us that the part is bad. It will not work at all. He has ordered a new one, and requested rush service, which I think they will ignore. I cant help but think these parts are manufactured somewhere outside the USA. Well, listen to this Whirlpool, I would rather pay $25 more for this part, and have your washing machine work. Dirty laundry might seem unimportant to you. It is not unimportant to us! If you cant do better than this, make something else. I am furious, and will spread this news to everyone I know, and I will report on this situation again.

Purchased Model # wtw5000DW0 Jan 3, 2015. Aug 15, 2015 started leaking water. Certified technician came to repair. Aug 17 - new transmission. Sept 3 replaced new transmission with another new transmission. Sept 8 called master technician at Whirlpool, needs new clutch assembly. Both technicians stated they dont know what is wrong with the machine. Sept 10 new clutch assembly and agitator replaced. The machine still makes a horrible grinding noise and is unusable. The technician has replaced everything but Whirlpool says it is still fixable. The Master technician has no idea what is wrong with my machine yet he refuses to call it broken. I have been without a washing machine for 3 1/2 weeks. They refuse to offer a return authorization number. I have spoken to a Supervisor on the phone. She states the warranty is for repair. They wont admit their product is a piece of garbage. They have lost a customer. She stated she will put my complaint in a file.

I bought YMFE330W0AW0 Whirlpool on sale less than a year ago and I have been angry since almost the beginning. This is a cheaply made product which angers me because Whirlpool is supposed to be a quality product. The clock cannot be set because we have to press really hard and that part of the stove head is broken now. I knew this would happen after only a few weeks but was wishing it would not. There is a lot of heat that leaks out of the oven continuously when trying to bake something. The top is horrible. This stove top does not keep an equal heating element so if you put it on low, it actually turns off for a few minutes and becomes red again for a moment or so. It is impossible to cook anything evenly. I HATE and DETEST this stove. The worst product I have ever known. If it is on sale...BEWARE.

This Whirlpool Duet washing machine is the worst purchase we ever made. The first problem I had was that after delivery, the balancer broke and it had to be returned to the store. 3 months later, my computer board went out. I have to wash twice because my clothes are not clean. 2 months ago, my hardwood floor was almost ruined because water was pouring out the soap dispenser because a sock sucked in the rubber hose and stopped it up. Today, Im unable to use my machine. Whirlpool should recall this machine. It’s too expensive and not worth the money. I do not recommend Whirlpool and will not buy any Whirlpool products again and will replace all Whirlpool products in my home.

Our hot water heater (Whirlpool Mod # BFG1F404053NOV) stopped working. I called the Whirlpool help line and was advised to change the thermocouple as they had been having issues with this particular model. I was advised to go to Lowes, where we had purchased the heater, to get a new thermocouple at no charge to us. After changing the thermocouple, guess what? It still didnt work. I went back to Lowes and they replaced the heater, at no charge to us (they were great during this whole ordeal so no knocks against Lowes). Well, one year later, it’s the same issue. The pilot light will not stay lit. It’s very frustrating as it never goes out at an opportune time. In the past, the name Whirlpool ensured you were getting a quality product. I guess that’s not true anymore.

We purchased a Whirlpool dryer almost three yeas ago. Its a front load, steam dryer--or WAS should I say. Almost a year ago, I was unable to calibrate the control panel (in other words, to change the cycle). Ive been advised by the tech that I need a new control panel $200. Really Whirlpool??? A $500 dryer that lasts two years?

We were a Whirlpool family, and have been using a Whirlpool front loader – Duet Steam Model # WFW9500TW - for the past nine years without any issues until recently when it started to vibrate. Technician sent by Whirlpool blamed it on failing bearing and that it was cheaper to replace than to repair (In hindsight, I wish we had tried repairing). Naturally, we decided to replace with a new front loader from Whirlpool - Model # WFW6620HW. Our previous version had a max spin speed of 1000 RPM and a capacity of 3.5 cu. ft. This new one has a top spin speed of 1160 RPM and a capacity of 4.5 cu. ft. The main problem with our old one was vibration, and this was being caused by the washer going into high spin while the clothes were not evenly distributed throughout the drum. In one spin, the clothes would spin perfectly without any vibration, but in another spin of the same cycle, the washer would not allocate that same clothes properly throughout the drum, which leads the drum to cause vibration from unbalanced high spin. Vibration is a problem, because like most Americans, we live in a wood frame house, and have a basement underneath with the washer located on the main floor. Vibration from unbalanced high RPM spin gets sent down to other areas of the house, causing damage, drywall cracks, separation in trims, etc. And these are all only the damages one can see with their eyes.One point about vibration and some myth busting. Provided that all your washer legs are meeting the floor and not on a saggy floor, your washer should not vibrate more than it does during an empty spin. If it does, then it is due to faulty, poor design/engineering. What happens is when the steel drum becomes unbalanced with laundry in high spin, it starts to shake as more of the weight is on one side, which one can notice looking inside the washer window. There are concrete weights fastened to the top and bottom of drum to keep the drum in place and to reduce its shaking tendencies. However, this weight also causes the washer cabinet to wobble if the drum itself is shaking. This wobble in turn causes the washer legs, which may be firmly grasping the floor, to very slightly come off the floor, which one can feel if touching both the washer feet and floor with their finger at the high spin of an unbalanced spin. And that motion of legs coming off the floor and hitting back at high RPM is what causes vibration to be felt on the floor and to be seen on the cabinet. Of course, this effect is amplified with washers that decide to go into an unbalanced spin with an even higher max spin. When our old washer perfectly balanced the clothes, it behaved like it was running high spin while the drum was empty. This is how all washers should behave, especially in America where the vast majority of homes are wood frame based. However, that was not what we experienced with this new Whirlpool. If a washer is not capable of balancing out the clothes, extra function or feature should be deployed in containing the drum shake to within the drum, and not allow it to escape.First, our old front load Duet Steam Whirlpool was Made in Germany. This new one is ‘assembled’ in America. The door window of the new one is plastic and feels cheap and flimsy, but I expect all the darker color door windows of newer front loaders to be plastic. Consider it cost cutting. We did not look for additional anti-vibration technology because our old Duet didn’t have anti-vibration features aside from its two springs and four suspensions. We decided not to use Load & Go because I have personally seen liquid HE detergents gum up over time, so I didn’t want to risk it gumming up inside the washer.After the installers left, I spend an hour cleaning the outside of the washer to perfection. Sadly, time wasted. Once I was done, I first did a wash without clothes, and then with clothes in Normal, fast spin cycle with drum about 2/3rds full. Just pants and t-shirts. There is a recirculating pump at the top of the drum to distribute the water, and to also distribute soap mixed water. But I am not sure if this is without problems. These pumps can collect soap residue with time, and you will eventually end up rinsing the laundry with soap mixed water even in rinse cycle.In getting to the first spin in wash cycle, I was flabbergasted to see how, just how rudimentary, I want to reiterate the word rudimentary, the load detection was before entering high spin. Our nine-year-old washer had a more comprehensive one. The new washer would spin the clothes at very, very low spin and simply see if the drum is most evenly spinning. That’s all. Compared it to our old washer which would also shake the drum to see if there was movement from side to side, because clothes can change their position when entering high spin. This rudimentary load detection causes the new washer to create an even worse uneven load distribution around the drum before spin, even though it may seem even at very low RPM. So, why is the new washer’s load detection so basic? I believe it is due to ball bearings.Front load washer models from other companies employ ball bearings to reduce vibrations from uneven loads. Whirlpool does not employ such feature, at least, they do not advertise them. However, to my surprise, I hear metal balls hitting each other every time the drum direction changes during the wash cycle. I inquired Whirlpool about this and I received contradictory responses. My theory is that the basic load detection before spin speed is used because Whirlpool assumes any changes to load distribution will be taken care of or reduced by the ball bearings of the washer. But this ultimately allows the washer to go into more uneven spins. The bearings may also be used to increase the tolerance of what is considered an ‘unbalanced load’ in order to get the washer to go into spin cycle faster, decreasing the time involved of the washer to go into spin cycle. Sadly, to my dismay, the new washer ended up causing a worse vibration than our old one with failing bearing.I called up the retailer the same day of delivery and complained of vibration. He first sent an installer to see if it was installed properly, and upon showing the installer of the vibration issues, the retailer sent me a new washer couple of days later thinking the first one was a lemon, and even though it has less noisy draining noise, it too exhibited the same issues with it going into significantly uneven spin. In the end, we decided to return the Whirlpool washer all together, at a loss of $200 because the retailer did not hold up to their spoken return policy.We have done many loads in this washer to see if our loading is an issue, loads of varying sizes, loads of varying types, loads of weights, and we maybe only had an evenly distributed load around the drum about once or twice. Once it was a King comforter. But, like our old washer, this too ended up not distributing properly around the drum in the final spin cycle and started vibrating, even though it was vibration-free in the previous high spin cycle. This proves that the problem exists directly within the washer, not the floor, leveling, load, etc.Some other problems with the washer: - The washer door, Load & Go dispenser at bottom, and single load dispenser at top are all plastic parts which all vibrate significantly during fast spin cycle. Especially the Load & Go dispenser which keeps hitting the cabinet to make banging noise. - Drain sounds are much, much louder than our previous Duet. It was even louder in the first one we received. Combine this to uneven spins and this washer can perhaps compete with an engine in terms of the sound it generates. - Single use dispenser at top left will hit the washer door if washer door is opened when the dispenser is also in open position. - Buttons are sometimes unresponsive, to which I have to power off and try again. But this has only happened a couple of times.- There is a small ¼ in. opening where the steel drum meets the rubber gasket, opening in which items like coins, etc., may fall through and are irretrievable. Don’t think small socks would be affected.To potential buyers, I suggest you proceed with caution when it comes to this washer. Understand the retailer’s appliance return policy and make sure it is shown in paper. It can save you a lot of headache. Get the extended warranty of three years because manufacturers only give you one-year warranty for a reason. I would also suggest that you avoid this washer at all costs if you have any floor level below where this washer is to be installed, especially if the level below is a basement. Your house is more important and more valuable than a $1000 washer.In the end, I am very disappointed in Whirlpool, an American company. Perhaps Whirlpool focuses their attention on top loaders, not front loaders. But Whirlpool had nine years to improve their washers, and it is sad that we may now have to go outside of America for a quality product to be used in American homes. P.S. No solicitation please, Whirlpool. This washer is in the process of being returned. P.S.S. I already posted this review in Whirlpools website, and it is under moderation.

We’ve had problems with our fridge where after we had it for about 2 months a crack formed on the inside, the repairman came and put a piece of tape, tape on a new fridge I wasn’t happy. Then we had our stove for about a month and the front right element went it was replaced but to this day it works when it wants to and I brought this to the repairmans attention when he came to replace an element in the oven and he didn’t even offer to take a look at it. We called Whirlpool on the 27th of December to get service on the oven and was told nobody could get here until the 2nd of January. This ruined New Years Eve Plans, New Years Day Plans and our turkey which should have taken a max 5 hours on Christmas Day took 11 hours putting our dinner off until 8:00 pm. We purchased the extended warranty ($700.00) to protect us from high bills for repair and this oven issue ended up costing us about $800.00 for meals out. I asked at the time of my call if there was some kind of rebate to cover our meals and the inconvenience over the holidays and they told me no, that’s pretty bad for such a huge company. Our dishwasher which is also Whirlpool hasn’t worked since day one, we had a repairman out and all he said was, run your hot water before you use it and use Cascade, it’s no longer under warranty and there’s pieces falling off and I have to wash my dishes before I put them through the dishwasher so what’s the use of having one. We purchased all Whirlpool because of the reputation but well never buy Whirlpool again or recommend them.

We purchased a Whirlpool side by side refrigerator from a local appliance store in December, 2018. We immediately noticed a loud humming noise coming from the refrigerator when the motor is running, which is a lot. We can hear it from our bedroom on the other side of the house. The store replaced the motor and the fan, but the constant irritating humming continues. The store called Whirlpool for advice, and were told that side by side refrigerators are louder. They also said that since it is working there is nothing they can do. We had a Kenmore side by side in the very same spot for over eight years. Never noticed when it was running. We will never buy another Whirlpool product again!

If I could give them zero stars I would. NEVER BUY A WHIRLPOOL GAS WATER HEATER! Our Whirlpool water heater Is 4 years old. Pilot light wont stay lit. A reputable plumber came out and said that the control knob is bad and to call Whirlpool to get part because its still under warranty. So I call and get nothing but a hassle. They tried to tell me that it was installed in a room that the installation manual says it not to be in. (Background here. The house was built in 1960. It is on a cement slab and its a prefab house.) The manual says Do not install in bathrooms, bedrooms or any OCCUPIED room normally kept closed. Now let me tell you where it is at. It is in a 5 by 3 boxed area with cement floor and walls to the ceiling with access doors to it and to the furnace which is also in this area. The access door to water heater is on the back side of a bedroom closet, access door to furnace is in a hall. So Whirlpool tells me that they cant give me the part Even if I pay for it due to some national fuel and gas code. They wont even tell me where I could buy the part... They said the only way they can help me is if I relocate the water heater or put in a ventless water heater. Our water heater is vented thru the roof of house... It gets plenty of ventilation. They wouldnt let me talk to a supervisor to complain... So this is why I am on here writing this review. I might add this is not our first issue with Whirlpool. Had a brand new KitchenAid refrigerator with ice maker. The ice maker didnt work from first day. After 3 techs and 3 visits it still doesnt work. Then also the compressor went out. If you want a better product and want good customer service then dont buy Whirlpool.Oh and one more thing. Our plumber also doesnt like Whirlpool. He said he had problems every time when he has to deal with them. He said its to the point when someone calls for services and tells him its a Whirlpool he just cringes. Now thats pretty bad. I just spent 4 almost 5 hours of my morning upset to the point of tears. With no results. Another note. I called my gas company. They said our water heater is in a safe place. If it wasnt they wouldnt be supplying gas to us. Live and learn. Done with Whirlpool.

We went out and bought the new front loader washing machine and dryer. Neither one of them works correctly. A service call had to be made the the day we ran the first load. The washing machine only washes errors popping up F8 and E3. On the dryer error code E3 pops up and cannot dry clothes. Worst purchase I have ever made.

Frontload Sport Duet ht: After just 8 years, bearing out on washing machine. Just had repairman out. Cost more to fix than what I purchased it for. I bought both the washer and dryer, thus the reason for the duet. So now I have a good dryer and lost its mate. I am not going to purchase another one. Very disappointed. I will not be purchasing any more Whirlpool products in the future. Off to the laundromat.

The dishwasher performs well but it is a little loud. The salesperson said that if I had purchased the model with a stainless steel tub, it would not run as loud.

Cabrio washer Model # wtw5840bw - I purchased this washer one year ago. It has a defect that comes along with it. You think your clothes are getting clean. But in reality they are not. This washer does not fill enough water to wash a small load of clothes. It has ruined three large bags of my clothes. Stained they smell in general they are not clean. Worst washer I have ever bought. General public Please be aware of this issue if you are going to purchase this washer. It is a big expense to be put out to the curb.

My Whirlpool microwave fits nicely over the stove/oven. It is easy to clean and comes with a glass turning table. It also comes with a wire rack if you choose to use it or it is easy to remove. I have had this microwave for 12 years and never had a problem. Love the presets on it for example ‘“popcorn.”

Wish we had gone online to check all the complaints otherwise we would have NEVER bought a Whirlpool model #EB9FVHLVS. Only 3 years old. First repair call to fix a manufacturers faulty grommet manifested by leaking in the bottom freezer portion. Just outside the warranty - did not purchase extended. Now I know why retailers recommend the extended. My sister overheard the repairman call in the product to his contact at Platinum Appliance Service Inc., and he made direct reference to the model number in the category of Whirlpool products known to have this specific design flaw, and that the product was never recalled but customers were directed to purchase a repair kit to fix the problem. Apparently this became a very well documented and repeated incident within the 1-2 year purchase date of these products and models with the known factory installed defect were still sent out to retailers at a reduced cost with no reference, warning or attention to the factory defect. Now 4 months after the first call we have to call in for another repair issue because our light in both compartments and the motor shuts off for hours at a time. We lost about $80 in meat products, so now were afraid to keep any costly items in the freezer because we cant afford to replace a $100 of thawed products every week on top of groceries already bought!!! It seems as though Whirlpool is gleefully generating business for appliance repair while making more than one hole in the consumers wallet.

I bought a new Whirlpool Top Load Washer four years ago and the paint was peeling off. I called Whirlpool and they offered to sell me a touch-up paint because it was out of warranty. I will never buy one of their products again.

Whirlpool Cabrio Platinum washing machine: You wont believe this until you call a parts replacement place for tiny part. The plastic (or vinyl) lid hinge bearings are located at hinge corners of lid. Hinge pin passes through them, one on each side. Half the size of a penny, UNCONSCIONABLE greed at the price of $32-$33 dollars EACH when ordered from a parts place. IMHO, design by INTENTIONAL failure to fail after three or four years. As a result, the lid will not stay up on its own. Then you find out the horrible news which is an insult to intelligence. Id have expected to pay maybe two or three dollars each, but NEVER the price they are demanding. Theyve got you and there is NOTHING you can do about it. At that rate, parts would run tens of thousands of dollars to replace the entire machine, part by part. These greedy clowns make car dealers look like reasonable people! The LAST Whirlpool machine of ANY kind we will EVER own!

I purchased a #Whirlpool; 4.3 cu. ft. Mini Refrigerator Stainless Steel BC-127B from @Target. There was a delay putting it into service (6 mos), so the Target store warranty was expired. The unit remained in its factory shipped packaging until put in service, so nothing out of the ordinary there. After barely two weeks of use, the compressor died. I followed all instructions (including waiting 8-10 weeks) from Whirlpool, but still have not received a refund or been given any information beyond we escalated it to our warranty team but havent heard back yet. The unit was a poorly made piece of junk in other respects as well. There are dozens of complaints about precisely this - defective units - on any site. Do not be fooled by the dishonest way that #Targets website lists reviews. Dig deeper.

I have been using this brand for many years. My first washer lasted for 30 years..so I will stick with what I know is reliable. It is a great machine. Very simple. I dont need anything fancy. 3 different cycles to choose from.

Ive spent more repairing this washer than what I paid for it new!!! Its really ridiculous that Whirlpool isnt more responsible for their equipment that doesnt stand up to their name! Ive replaced more things than I want to type but just to start the computer board, pump, bearings just to name a few. Each time I had my repairman out it was a minimum of $300 to repair. Ive had my repairman out 5 times to repair things. Thinking each time its cheaper to fix it than buy another which I surely didnt think I would be repairing it several time! At this point Im just sick to death that a washer that is for a home of myself and my daughter has broken down so much. I cant imagine what a family would go through. Even after all the repairs it still isnt right but Im done sinking money into this sinking ship of a washer! Its loud constantly stops due to un level so I have to move the clothes around usually having to repeat this several times before I can get the load to finish!!! Then they come out wrinkled more than they went in and I have to iron clothes. A person should NOT need to iron! May as well wash them in the river on a rock. It would be easier!!! SO DISAPPOINTED!!!

I bought a Whirlpool washing machine from Home Depot 4 years ago. It immediately started to grow mold in the seal even though I wiped it clean after usage. I called a certified technician to replace the seal. As he was removing one screw on the lock the Washing machine shorted out essentially destroying the panel and rendering the machine broken. I called Whirlpool and told them that the machine was defective otherwise, why would it do that? My technician has worked on hundreds of machines and this is the first time this has happened. The two managers I talked to refused to help me because I didnt have an extended warranty.It is true that I dont have an extended warranty but also, I had faith that Whirlpool had sold me a good product. There is no other explanation for the washing machine to do that other than it was defective. I asked the managers to send me replacement parts, but they refused to do that. The last machine I had was a Maytag that lasted 20 years and when I gave it away, it was still working. I expected no less from the Whirlpool I purchased at Home Depot.

Not completely happy with my purchase of the Whirlpool Gold Series refrigerator I just paid off this month. Have had the refrigerator for one year. To be as large as it is, it really doesnt seem to be able to hold that much food. The refrigerator is on the top and the freezer is on the bottom. We began having issues with the ice in the ice maker becoming frozen together and forming clumps of ice. The ice felt damp to the touch rather than feeling completely frozen. We called the manufacturer and they said to be sure the vents in the freezer section were not blocked by food. So you have to be sure to load the freezer so that food doesnt block the vents. Additionally, when filling your glass with ice from the door, unless you are EXTREMELY careful, all of the ice will not go into the glass but spill out onto the floor. Weve had the refrigerator for one year and I still have ice coming out that doesnt make it into the glass. It is not user friendly at all. One last thing - the refrigerator has double doors and to get to the section of the middle pull out drawer, you have to open both of the double doors, letting out a lot of the cold air. For the expense of this particular refrigerator I would not recommend purchasing it. My last refrigerator was a Whirlpool as well. It lasted 17 years and I was very happy with it. This Gold Series was supposed to be a step up, but I feel it was a step down.

Our over the range Whirlpool microwave door casing is disintegrating where the door handle screws to the door. Big chunk fell off today.

I’ve had this washer since October 2018. Worst purchase ever. It does not clean the clothes nor does it put enough water in it. I’ve tried the deep water option too and it’s for sure still not enough. I don’t understand how they even thought that this was perfectly fine to sell. If I could’ve taken it back a month after having it, I for sure would. And no one will buy it because they’ve read reviews of how it’s terrible. I wasted $900 on this washer. I have the dryer also which works amazing. The washer just sucks something terrible. My husbands military uniforms always look dirty and a lot of the clothes aren’t ever wet. I’ve finally seen a picture of how you’re supposed to have clothes in there. Why in the world would you only allow barely a layer of clothes at the very bottom to be cleaned by the agitator? Why would you have this huge drum only to put not even a load in there? This was such a waste Whirlpool and I’m glad I’m not the only person who has the same issue. I will never purchase another Whirlpool washer, it’s upsetting I can’t currently get rid of this crap washer I have now.

Had a part come off right after our purchase but was a easy fix to repair. The silverware basket also kept coming off until we looked at it and realized it was on wrong. This dishwasher is much quieter than our last one. It also shows fingerprints. We got this dishwasher in a group purchase during a sale at Lowe’s that included the refrigerator a stove, microwave and this dishwasher.

I used the Whirlpool website contact form, and described an issue I have with the Cabrio washing machine. When the form is submitted, it states that the company will respond in three business days. Two weeks later, after no response, I submitted a second contact form. It has been five days, and I still have not received a response.

We got a DEAL for this nightmare for nearly $700 back in 2014. Nothing but problems. Constantly finding plastic pieces at the bottom... some identifiable; others not. They are from the cheap parts within. The control board lights (all but 1 works) went just after the 1 yr mark. We are now having to replace the top Rack Adjuster (MORE CHEAP PLASTIC), as it has been barely hanging on for the last year and a half... constantly fighting it, as it would drop all the dishes if you moved it wrong.Now, the water is not draining at all... period. We clean this religiously - always rinse dishes completely, use rinse aid, never stuff dishes. Today we find a random plastic piece, which we are now trying to identify. NOTE: we dont put plastics in the dishwasher. So, today a new plastic piece and major drain problems. We are in the market and purchasing a new French Door Refrigerator and Front Load Washer. Will NOT be going with anything Whirlpool. Not much better these days, but this name has a big RED NO for us. Made it even worse when we contacted for help after that 1 yr mark. NO HELP AT ALL.

We purchased this Whirlpool Cabrio washing machine from Sears about four, maybe five years ago and have complained repeatedly. We have had repairmen out numerous times. Of course, they have had to order parts. My clothes are not getting clean and they now have an odor to them. The machine is getting noisier and noisier and it is rocking like crazy (I had to put plyboard underneath to protect the floor) during the rinse cycle. The water sprays out erratically and sprays even slower for cold water, then warm water, which was weird! Thankfully, I still have it under warranty (I got the extended warranty). I am now getting ready to call them again. I will never buy this brand again.

Horrible customer service. No help in trouble shooting your the appliance. Whirlpool only wanted to send a service technician. Several things have gone wrong with this dishwasher that came brand new, in a brand new house. After the year warranty is up, forget about any help from whirlpool. I would hope you would not have to purchase extended warranties on any new appliance but that doesn’t seem to be the case. My dishwasher was only three years old and on its way to dishwasher heaven. I was told by a repairman that whirlpool had a problem with their motors. Whirlpool would not confirm or deny this. I felt like I was really taken.

I purchased a Whirlpool Refrigerator with French Doors, Model No. GX5SHDXVD03. Within 1 year and 4 months, I had to replace the defrost control board. I spoke to Whirlpools customer service, George ** said he was sorry for my inconvenience but that he refuses to help in any way because I missed the warranty period by 4 months. I spent $352.74 for the parts and labor and lost hundreds more in food. Do not purchase any Whirlpool products. I was told that the boards have been going out frequently.

Overall, I am happy with my Cabrio BUT we purchased a Whirlpool WTW7000DW0 Cabrio top loading washer w/ electronic touch panel in May 2016. We experienced water hammer from day one. I finally had enough yesterday and knowing that the plumbing could be suffering (15 year old condo), purchased 2 Sioux Chief MiniRester, Model 660-H arresters (Lowes at $9.99 each) and had a plumber install them today. I could have but am nursing a fractured rib. Long story short, they work perfectly. There is NO indication elsewhere in the unit that water is even entering the tub unless youre standing right beside it.Ive been told that hammer problems exist in ALL high efficiency washers, all are prone to this problem. I was also told by a Whirlpool support person that the Cabrio is a Samsung design and the pulsing of supply water off and on, over and over is normal operation. If I had been informed when purchasing that hammer is a common problem, I would have installed arresters from the get-go. At the very least, manufacturers should include arresters as a part of the sale; installers should make sure that every new installation includes arresters. All told, I am out just under $200.00 for new technology that really could have been engineered out in the beginning.

How I wish I had read this board before purchasing! This is the worst washing machine made. Put your clothes in the sink, add water to cover two thirds, add detergent, slosh around slowly for a few minutes, wring and remove. You have replicated a Cabrio wash! I have complained repeatedly, had a repairman who assured me it was working properly (as designed, too little water, too little agitation). I was a lifetime Whirlpool client.

[Model WTW6300WW0, Type 580] A few years ago Whirlpool goofed - they left out the Perma-press cycle on a high-efficiency washing machine model.We noticed the absence of Perma-press (or Casual as it sometimes now called) on the shop floor, and were assured we could arrive at the same results with the dizzying array of buttons that allow the consumer to tailor the cycles to their wash load. It turns out that it doesnt allow this. Buttons are disabled on some of the cycles, thereby preventing recreating a Perma-press cycle. No amount of prodding... Whirlpool has provided me with an override for the combination of a normal wash and a gentle spin that comprise a typical Perma-press cycle.On contacting Whirlpool about the missing cycle, they claim consumers no longer want the Perma-press cycle. Puzzled by this statement, I returned to the showroom floor to see for myself. All the washers have Perma-press cycles. Whirlpool goofed with this model. They left it out. They have not provided a replacement machine for a consumer who blows this whistle on their goof. Among the solutions their customer support DID provide: add softeners to the rinse cycle and add dryer sheets to the dryer to reduce wrinkles [by purchasing a high-efficiency machine, we aimed to reduce waste, not increase it]. Among their invalid suggestions: choose the Casual cycle [there is no Casual cycle setting on this machine]; choose Normal cycle, then set spin speed to low [this machine disables the low speed choice on the Normal cycle]; on this machine the Perma-press cycle is renamed Delicate [Wrong. Delicate only swishes clothes back and forth, not robust enough for business shirt colors and cuffs]; on this machine the Perma-press cycle is renamed Colors [Wrong. Business shirts come out too wrinkled on Colors]. There has been nothing I can do to convince Whirlpool that they produced a lemon in this model [Model WTW6300WW0, Type 580] and should replace it with a normal washing machine. I have tried for years, only for Whirlpool to come to the same conclusion: its the consumers problem now, not theirs.

Approximately 2 years after purchasing a Whirlpool Gold Bottom Freezer refrigerator, I noticed cracks/openings on the interior walls on the ledge that holds the glass shelf! It is completely Crushing the styrofoam inside the refrig? Also, signs of being Cheaply made veggie bins are held in place by a piece of plastic that cracked after a few months. This was in 2011. First, I contacted the service contract people. They told me this was not covered under the policy. Next, I wrote & called the company. The walls show the styrofoam stuffing in the refrig. The shelves rest on these openings in the vinyl walls of the refrig box. This is a disaster and the refrig was 1400$$$. I have extended warranty which does not cover structure!!! What can one do with a New expensive refrigerator that has cracks in the Wall of the refrigeration box? Is there a class action suit anywhere that I can join?

I have purchased Whirlpool refrigerator 2 years back. Suddenly my refrigerator stop working. When I filled complaint against this in customer service care. They sent technician. He told its compressor not working and asked 2800 rs for gas filling. Then he said hell come tomorrow for this. For 4 days he didnt come. After 20 calls, to customer service centre they said, Your refrigerator has to sent to the center. For that they asked 1000 rs... We were so disturbed by their slow service. We immediately said yes. Now when our refrigerator arrived at their center. Now they are again asking for 3400 rs for other part. Im so frustrated by this service. What type of warranty you are giving.. The warranty is of just the box.... So bad products. Such a bad experience... Never gonna buy Whirlpool product again or recommend anyone.

This microwave oven has worked well now for about six months and overall we have no complaints. My only complaint is that it has a cheap feel to it, especially when the door is closed...it creates a rattle type hollow noise....it just does not sound like it is well made. Time will tell I guess. The unit works well and heats fairly evenly. The cook options are plentiful but we rarely use most of them as we are usually merely re-heating food or coffee. The defrost cycle does work well for us.We purchased this microwave oven as well as a Whirlpool Range and Whirlpool French Door Refrigerator at the same time from a small Home Depot. Whereas that store had the microwave on display it did not have the other two on display and therefore we purchased them sight unseen....a BAD, BAD mistake. I have reviews for those two so I will say no more about them here. Thus, overall, we are very pleased with this Whirlpool Microwave Oven and would recommend it.

Its a piece of junk. The only time it will finish a wash and spin dry is when it is empty. Otherwise, it stops and lists an unbalanced error code. I opened up the service panels and found no broken hangers or clothes. There’s no way to bypass the system. I have read of similar issues and of course, its just out of warranty. I assumed the warranty was like other brands but it’s much shorter. What to do? Purchase a washer with dials and not a brain; it will last years. Note that the models without a brain cost far less.

Just like many before me... Renovated my kitchen. Had my model WRF767SDEM purchased from Lowes (not much help either) in my garage for 2 month before plug in. After 3 months upper part did not cool, lost food to spoil. Call WP. Tech came. It took 3 wks for part to be replaced and worked for a month. Now we are waiting for a new part to arrive for the second time > Tech Stated it is a known design defect issue by Whirpool. (But units still being sold everywhere.) WP Should recall this units and stop selling them!! IT IS A LEMON FRIDGE. Do not buy!!! I wish a law firm read all of these complains and make this a class action suit out of this, It will be the only way Whirpool can be held responsible to Us the consumer!! Yes I am mad after $2600 wasted on a POS fridge and a deplorable customer service!!

Bought a whirlpool water heater less than two years ago and it has already failed. I could not find parts for it and was told by a lowes employee that I would have to call whirlpool on the 5th of July (three days away) to order any parts. I tried three plumbers in the Indianapolis area and they all told me that I would be better off replacing it with a different brand. I just put in a new rheem in its place. I will never buy another thing from whirlpool. They are no good.

Well, this saga continues. Whirlpool dishwasher was purchased at the HH Gregg on Rockville Road on March 17, 2012. Whirlpool dishwasher broke down on May 17, 2012. I bought the extended warranty but who cares? HH Gregg doesnt because it does not go into effect until a year after purchase. So since its less than year, I called Whirlpool, who sent someone out a week later, who, of course, cannot fix the brand new dishwasher because 2 parts had to be ordered. This was almost 2 weeks ago! I still have not heard from the company, A & E, who works for Whirlpool here in Indy. Whirlpool called me on Monday to tell me theyre sorry and blah, blah, and will try to find part in five more days. Then ship it to me, and, of course, it will probably take another week for the maintenance man to fix it. I mean, I grew up having to wash dishes by hand, so no big problem. But when you spend $600 to $800 for a supposedly nice product to enjoy the leisure time of your life and get extended warranties, you expect it to work for at least 6 months before breaking down. So be warned. Do not buy Whirlpool, and furthermore, beware of buying extended warranties and appliances at HH Gregg.

I purchased a Whirlpool catnip washer from Brandsmart in August of 2010. It worked fairly well, but would sometimes need for clothes to be rearranged in order for the spin cycle to complete. In June of 2013, it started to not wring the clothes out completely. It then stopped working. I called a repairman and got an estimate of $550 dollars, but I paid $578 for it.I called Whirlpool and spoke to the supervisor of the consumer concern team. She offered me a fifty percent discount on the parts for the repair. I checked the web to see if anyone else had any problems with this product and found several. I suggest you do your homework before purchasing a Whirlpool washer. I was positive they would do more, since it’s such a prestigious company.

Ice maker stopped making ice. This side by side Whirlpool refrigerator was purchased 4 years ago. We called Whirlpool. An authorized repair man identified the problem. At the bottom hinge of the freezer door two of the wires have been broken. A defective design, but no recall from Whirlpool. The solution is to replace the entire freezer door for a cost of $1200. Ridiculous that a replacement door cost more than the purchase price from Lowes. It would appear that these 2 wires could be reconnected, but Whirlpools only solution is an entire new door. Automakers stand behind their products with recalls, but its not the same with Whirlpool. Love my Whirlpool range, washer and dryer, but this counter depth side by side is a real loser.

This Whirlpool Gas oven with 5 burner top is very good and has given us 12 years of good service so far. The only issue is that the stovetop and oven are not easy to clean and keep clean. The finish is good and has no chips. I would expect the top to be easier to clean and keep clean with the finish technologies available. Same for the oven window glass - it is not easy to clean and keep clean.

I had purchased a hot water heater on Saturday and installed it myself. I filled the tank and waited about twenty minutes before turning the power on. I waited a couple of hours before testing the water temperature and it was cold. I checked the temperature setting and it was set at one twenty five, I went to Lowes and informed the service person and was told there was nothing they could do about it, I had to call the number on the tank for Whirlpool. I called the number and was told they could come out to check it but we would be responsible for the labor charges. I didnt understand why because it was under warranty and we had also purchased the extended warranty. I informed my wife so she could deal with Whirlpool because I was going to work. My wife called a number of times and was getting transferred from one person to another and getting no help at all. She was told by one person that it was maybe a problem with the wiring in our home or maybe the plumbing. One person told her that it was not their problem. We had to finally pay an electrician to come out to look at it and had to pay him to replace a heating element. The cost of the electrician and the part came to an extra two seventy five dollars. The only real help that we received was from Lowes managers that were willing to take the water heater back if we could get an authorization number to return the water which Whirlpool claimed they did not have any type of a number. Our 400 dollar water heater turned into an almost 700 dollar water heater. We had also purchased a refrigerator from Lowes that was the Whirlpool brand that quit working after about four months and we had to pay to have it fixed. Needless to say, we will never again purchase any Whirlpool products or recommend them to anyone. The service was very very poor and we are not happy with Whirlpool.

I purchased the Whirlpool Cabrio about five years ago. Last year, the motherboard had to be replaced. This year, it started load balance issues on the spin cycle; in other words, it wont spin without sounding like its going to tear itself apart. It cost $100 to have someone look at it, and was going to cost almost $400 to repair, and whats next? I spent a lot of money for this machine, and Whirlpools answer was to offer me a discount to purchase a new Whirlpool. Do I have Stupid tattooed on my forehead? I will never buy a Whirlpool again!!!

We purchased a Whirlpool Overhead microwave and Quiet Dishwasher in May of 2017. Within the first year, the microwave needed new sensors installed. The repair person said this was a design flaw and he was getting many calls. Then at 13 months, the dishwasher wouldnt drain. The repair person fixed the problem and left reset directions because this can commonly happen. Now at 18 months later, the drainage problem wont resolve even with the reset. Whirlpool extended the warranty by 6 months but wont cover this repair. Two appliances, two problems. Dont buy Whirlpool.

I have the Cabrio washer that is only four years old. It is leaking oil and is very loud during the spin cycle. I paid $800 for this washer and am extremely frustrated that it didnt last longer than this. I contacted Whirlpool customer service and had no luck since it is out of warranty. Due to the high number of complaints with the same issue, please consider a class action lawsuit. Thank you.

I purchased a Whirlpool classic range model number rf263LXTS0 on January 2010. We had some hang-ups on the kitchen renovation and were not able to install the appliances until May of 2011.I used the cooktop that evening and was very pleased. I then went to use the oven 2 weeks later and it did not heat up. I asked the contractor to check things out (maybe it was something minor that he could fix). He checked the things that he installed and everything on his end was working fine, so he told me to call Whirlpool.A service technician came out and, within 10 minutes, said that the oven controls were defective.I paid $450.00 for the oven originally. The service technician charged me $136.74 for 10 minutes to tell me that the oven control needed to be replaced (that is the major part of the oven) and that it would cost me $318.41 to replace the part.I called Whirlpool and explained my circumstance and Paula, the supervisor from Tennessee, said that there was nothing she could do. I told her that even if I installed the oven back in January of 2010, the major part of the oven should last more than 1 and 1/2 years.What terrible craftsmanship and crappy customer service. It is sad that customer service cant stand by their product and Whirlpool has to rely on making their money on repairing defectives products. I now have to go out and buy a new oven. I also buy a lot of appliances in my business and I will never buy a Whirlpool again.

Good microwave and will have 1100 watts Of use for TV dinners and warm up food. Do well and goes well. Please use this as well to warm up TV dinners smaller than most. Test them and see what is best. Go.

I purchased a Whirlpool stove, microwave and fridge in November 2012. The fridge model #WRT771RWYB01 has been a lemon from day 1. I have had the repairman out for the same issues multiple times. Ice build up in the freezer, water tube to the ice maker frozen, food in the fridge freezing, blah, blah. They have taped, glued, replaced everything they can and to no avail. It still happens. When you call for service, it takes 2 weeks or better to get someone out. I will NEVER buy another Whirlpool product! This has truly been a nightmare experience!

We purchased the Whirlpool Cabrio washer & dryer. The glass lid design is VERY POORLY constructed and should be replaced by Whirlpool. We paid over $200 the first time the lid broke and was told this is going to be a continuing problem. They were correct! We subsequently replaced the lid 2 additional times only to have the same break on the right hand side causing the lid to pop up. Something must be done and WHIRLPOOL need to care for their machinery. They should replace the lids or provide a major incentive for consumers to replace the washer. PLEASE DO SOMETHING!

I bought Whirlpool dishwasher (silver, Golden Series), after one year it just stopped for nothing and the circuit controller failed with error code E2/F2. So it was expensive but turned out to be totally unreliable. I had to pay $200 to get extended warranty and still waiting for the parts!!! Worst experience ever (uh Golden Series, for me it is Plastic Series). Will never buy any product from this company again.

I bought one of the top of the line Maytag washers and was very disappointed. It only lasted about 5 years and had to be replaced. The dryer I bought at the same time is still working. It is 15 years old.

Overall??? Ive owned this Whirlpool side-by-side refrigerator for a year now. Love it except for semiannual cost to replace the filter. My brother recently installed the same model in his motorcoach. Yes I recommend this appliance.???

Just about three years old our washing machine started making a horrible noise and soon after a horrible smell. Won’t complete spin and dry. The bearing inside the drum has failed. The pump is making an unusual noise. I see a lot of reviews about this product. I find it strange that it appears to have a good rating at all the advertisers but in reality it’s really a horrible machine. Shame on Whirlpool for our landfills, dumps and recycle bins with absolute garbage plastic and metal Has to be recycled. We have only disposable garbage for appliances.

I have a double oven. The bottom oven takes a long time to warm up. Good oven overall. I would definitely recommend this oven. The timer functions seem to work well and it is self cleaning as well.

I have had my whirlpool oven for approximately 6 years. This will be the 3rd time I have had to replace the thermal fuse. For the last three times I have used the auto clean, it blows out the fuse. It has cost me $110.00 each time I called my appliance tech to replace the fuse.

I purchased a Whirlpool duet set on sale at Lowes about two years ago. The front loading washer has been leaking when I put in a full load of clothes. It usually floods the floor when it leaks. I am upset and very angry because this leak has ruined the doors to my washer doors. Apparently, the defects with this machine was known by Lowes and the Whirlpool company at the time that I purchased it (thus the sale price). This was not forementioned at the time of purchase. What a lousy way to do business. Whirlpool screwed me. Shame on me. Never again.

Our long and tortuous experience began in 2013 and continues to this day. But Ill just give the headlines. In August 2013 we bought Whirlpool BTM French Door KFIS20XVMS11 from Lowes. Three years later we learned that model number appeared on the attached recall notice which had been issued just days before our unit was delivered in September. Neither Lowes nor Whirlpool notified us of this recall which described a simple repair to a part that was leaking so slowly that its effects took three years to show up in a destroyed floor and cabinet enclosure that will cost $2981 (and still rising) to repair.We called AIG, the company behind the extended warranty provider, and they responded promptly by dispatching a Whirlpool factory authorized service technician who attempted unsuccessfully to drag the unit from its alcove over the warped, erupted floor beneath. With the refrigerator half-way out of its enclosure, the technician stopped and asked us to sign a waiver of liability. When we refused, he announced that the problem was water damage and he jammed the unit back into place, leaving dents in both doors and the freezer drawer below.We went to Lowes, who strung us along for several months before sending an engineer whose report concluded that the problem was a manufacturers defect (The Lowes engineer and his associate damaged the unit further when they forced it back into place over a floor made more uneven when they removed the pieces of rotted oak shown in the accompanying photo.). Based upon the engineers report, which Lowes said it had no duty to share, we were given a 1-800 number for Whirlpool customer service, with assurance that we would be taken care of. Although we had to start from cold without the engineers report, Whirlpool customer service was initially very accommodating and gave us hope. For a moment, I thought we were going to get resolution. They assigned a case number and we supplied the requested documentation. That was on a Friday in March, 2017.Monday we were surprised to receive a sternly worded notice from the Whirlpool Law Department that a clerk there would be taking over our case. We realized that we were far from resolution. Why did the Law Department intervene? We dont know. We guess it may be because they want to avoid a class action lawsuit on behalf of possibly thousands of leaky refrigerator owners (Whirlpool, KitchenAid, Maytag, Jenn-Air and Amana units were all among the affected). In any case, since January we have been monkey-in-the middle among Whirlpools various departments, Lowes various departments and AIG, with no progress. What do we want? We just want things back the way they were before our leaky refrigerator did its damage and before Lowes and Whirlpool demolished our good as new looking KitchenAid refrigerator in the process of telling us they wont fix it.Footnote: We purchased all new KitchenAid Architect series appliances in August/September 2013, including top of line cooktop, dishwasher, convection microwave, convection oven and a French door cabinet depth refrigerator. Every unit except the cooktop has required warranty service, including five expensive electronic parts replacements. Fortunately we bought extended warranty service from KitchenAid/AIG, who have been terrific to deal with on the parts replacements. I dont recommend Whirlpool appliances but if you are intent on buying them, I do highly recommend extended warranties. As for the value of Whirlpools manufacturers warranty, watch this space. Ill be back with the final resolution.

I received this Email from the Whirlpool Director of Consumer Care to evaluate my experience with their customer service department. I filled out the survey over a week ago including a complete documentation of my problems and have not even received an acknowledgment of the survey or promise to look into my problems.In the last 7 months I have experienced problems with 2 Whirlpool major appliances which both appear to be unrepairable and which have been unsuccessfully brought to the attention of your customer support group. In March a fridge and in October a clothes washer. Both were high end products roughly 3 to 4 years old. I did not have an extended warranty with the fridge so I dealt directly with the customer support group. However I was covered by warranty with the washer and your distributor Bad Boy have been making the calls on my behalf but have been just as disappointed to date as I was.Both cases were very similar. In both cases the repairman came out within a few days and promised to return the following week with the broken part but I have never heard from either one of them EVER. In the case of the fridge I was told to defrost it the day before the promised repair date and lost all the food $$$. At this stage a number of calls went out from me to Whirlpool for the fridge and from Bad Boy for the washer and eventually we both got a new delivery date of roughly one month. Both times the date passed with no shows and no call backs. Repeated calls later to the customer service group, with promises of EXPEDITING the delivery, the fridge part delivery date was extended to 3 months so we had no choice but to buy a new fridge. As for the washer, Bad Boy even had an unsuccessful face to face meeting with your representatives and we have had no word back or expected delivery dates well into the third month.I HAVE NO IDEA WHAT TO DO? I have made so many calls with so few call backs and no clue what to expect or when? Your representatives use the word expedite with no idea what the word means. At the suggestion of one of your representatives I even called one of your distributors Sears to see if they had the part. Their Canadian head office is in the Philippines and they said they had the same problem with Whirlpool. Twice I tried to talk with your representatives supervisor and both times were unsuccessful.In a world of computers where it should take seconds to find inventory parts and expediting packages usually refers to next day delivery, the fact Whirlpool requires months is unbelievable. The only explanations I can come up with is 1- You dont make parts for your appliances. 2- New appliances are made so poorly all parts are gone. 3- You could not care less about your customers. 4- You dont own a computer. Most of our appliances are Whirlpool because we thought you had a good reputation. We had to purchase a new fridge and still have had no word on the washer?