My dishwasher is one year old. It is very quiet and cleans well. Stainless steel makes it look great too. Efficient, energy saver dishwasher with great capacity and large utensil holder. This is the best dishwasher I have owned.

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

This machine (Top-Loading High Efficiency MVWB755DWO) does not clean, it only leaves soap and moldy residue on clothes. The Whirlpool company refuses to assist even though it was delivered less than a year ago. So much for warranties! Wrinkles clothes, wrings incorrectly and does not give you freedom to manage independent of technological controls.

I have bought a new Home Depot Maytag Impeller HE washer. After 6 repeat washings of 2 items that are lightweight dark brown it was obvious after drying they had soap and lint and lot hairs on it. I reached with no he detergent. The last 4 times the water level filled to 1 depth even for high level water setting to extra rinse or power wash settings. I went to Home Depot and they suggested I call Maytag repair center on Tuesday after the labor day holiday to have them check it out. I will also call the supervisor at Home Depot as I do not feel paying $600 for a faulty machine is acceptable.

I purchased high end Maytag washer, dryer, dishwasher and microwave in May 2010. On Saturday 4/25/14, the Maytag Microwave stopped heating. The fan runs, the panel, display, lights, clock, and tray all work. It just doesnt cook. The Microwave was installed in June of 2010. Not even 4 years old. I have tried to troubleshoot via the instructions that came with the microwave, i.e. Check the demo mode is not on. Dont know why after 3 yrs it would be, but checked it. No help. Pulled the plug out and replaced; turned breaker on and off; checked to see if its was locked. Nothing. I then checked the door and I found that the plastic inside panel on the latching side of the door is pulling away from the door itself, which is part of the locking system. The magnetron shouldnt work if the door system isnt closing properly. The latch system is what is causing the door to pull apart. I am wondering now how much microwave exposure my family has been getting from a malfunctioning door? I have had a Microwave, dishwasher and refrigerator made by Maytag in the past. The refrigerator is 14 yrs old and still works fine. The microwave and dishwasher were at least 10 yrs old when I replaced them with the new Maytags I have now. Here is the problem. Maytag is not Maytag Corp. anymore. Whirlpool Corp now owns the Maytag brand. Prior to the old Maytags I had, I had GE fridge which was junk, and Whirlpool, dishwasher, stove and microwave. They were also junk. I swore I would never buy Whirlpool products again. Surprise.

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

I changed from another HE brand to this model. No comparison. This machine can do twice the work... but double the time. My former machine was quiet while this one is not. Maybe I got spoiled to the former brand, but Ive never heard so much noise from a washing machine! Ive always thought Maytag meant quality but I think they may have missed the boat here. I tried reviewing on their site but when I gave it two stars, I got an error message. Clever, Maytag.

The Maytag Neptune FAV6800AWW Washer has to be the crappiest product I have ever bought. I bought it brand new and hardly ever used it. The first time it broke it was luckily under warranty, although we had to pay for the repair man to install it. It took two new circuit boards before it was fixed. A few months later, the circuit board went again, and it was conveniently for Maytag now out of warranty. The repair man told us that their company never carried these washers because from the get go they had a ton of problems. He said that the odds of it breaking again were great and that we would be better off putting the money into a new washer.I dont understand how the company, in good conscience, could continue to sell a product to consumers that they knew was faulty. It was not a cheap washer and I have never been so disappointed in my life. You would think they would have had a mass recall or, knowing how many problems consumers were having with the product, offer so much money towards a new one.I laugh at the commercials where the Maytag man was bored because their product never broke I could have kept that man busy for months!

I purchased my Maytag washing machine in June 2011 and within the first couple of uses, noticed that my clothes did not appear clean. I went back to Home Depot and complained and was told I had to use HE laundry detergent and I was. I gave it a while longer and still, nothing I washed ever seemed to come out clean. Sometimes, the fabric softener dispenser fills with water; other times the fabric softener remains in the dispenser. The machine makes very loud clunking noises during the wash cycle. I knew this machine was a lemon from the get-go. I should have insisted that Home Depot come take it away. I will never buy a Maytag appliance again! Maytag should have recalled this washer long ago and, if there was a Class Action law suit, I would surely join in!

Under class action suit in 8/2005, Maytag repaired my Neptune washer by replacing motor conversion kit. 6 yrs later the washer is having same problems as had originally; we asked Maytag just to replace the motor drive again ($190.00 part). They refuse, although this motor drive had identical life span to the one they replaced. It seems the replacement part was not new and improved, it only lasted as long as the original. Only now, we are past the class action suit deadline by years.

I purchased a Maytag dishwasher in March 2005. About every 8 to 12 months since Ive owned it, the control panel malfunctions and needs to be replaced. I was told by the repairmen (similar to the many other postings below) that the malfunction is due to a faulty design where warm moisture shorts out the electronic control panel. For a few years, I paid for a service contract. But this seemed quite unfair, given the regularity of the same malfunction. Given that this is such a common problem, isnt there some responsibility by Maytag? This is clearly a faulty design. What about the legal responsibility for a recall? Is it possible that, together with other aggrieved owners, a lawsuit against Maytag would be the appropriate action?

We purchased a Maytag 4000 series washer and dryer in October 2011, and within 5 months, the main bearing failed. The Maytag repair person told us it was an inherent issue and to make sure we use HE detergent (We always have.). Maytag advised parts were not available for 3 weeks, so no washer after 5 months of use. The bearing failed a second time after 11 months. Maytag refused to replace the washer and advised it was repairable condition. Now, we have the bearing fail a third time, and Maytag has advised that they would not repair the washer under the extended warranty program. They offered us 75% refund on the washer (So I guess they expect their products to only last 4 years.), which is simply unacceptable. We are now faced with purchasing a new washer, which will not match the dryer; or we have to purchase a washer and dryer of another brand. Maytag has provided pathetic customer support, and their response or lack thereof shows that they simply just dont care about their brand image or the customer.

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

Maytag Bravos Series 300 - I bought this machine less than a year ago. There is an awful smell coming from the machine that I never smelled from any other washer I have owned. The clothes do not look, feel or smell clean, and my towels are ripped. It is an extra large washer, yet when blankets are put in the machine bounces and shifts. After reading all the reviews, it seems I am not alone in my concern with a machine that was not only expensive, but was told it is a great product. Maytag needs to do the right thing and recall this machine.

Same as everyone else, ice freezes up on the bottom and water runs out all over the floor, ruining my new floor. Whole kitchen was new including all appliances. Maytag is ruining my floors. Can find no drain pipes so not sure where the water is supposed to do. I think they forgot to install one. But I am getting pretty sick of seeing my floors ruined and stepping in water.

I got a washer from a Menards Store in Fond du Lac, WI. I was given a line of crap at how great it was, and because Ive used Maytag for years I bought it. Id rather have my 20 plus old one back. At least it didnt take over an hour for a load, and the rinse cycle really worked. WE HATE YOUR NEW WASHER. As soon as we can afford a different washer well be looking for a different brand.

One year ago I bought a Maytag Micro-wave and a Maytag dishwasher - big mistake. I should have done some homework. I had problems with the dishwasher since the day it was installed. I should have suspected something was wrong when it was delivered. I opened my front door and there stood a deliveryman holding my dishwasher in his arms. He said, Where do you want it? I couldnt believe he could be carrying it by himself, especially since it took three of us to move out the old Thermador which by the way was still working just fine after almost 30 years. But my wife insisted on a new washer for her new kitchen. The Thermador was actually made of steel. The new Maytag was made of plastic even the motor. It had some steel and copper parts but mostly plastic. I dont think it weighed forty pounds. The problems began the first day with leaks through the door and under it. I suppose eight or nine service calls happened in the next 3 months. The factory service men were different each time and each had their own guess as to what caused the leaks. Over time they replaced all the parts that could be leaking some of them twice, because subsequent servicemen discovered that a previous service man had installed the wrong parts. We often had to wait several weeks because replacement parts were not on hand, and would be ordered and shipped directly to us. Then we would have to schedule another service call, only to find out the wrong parts came - more delays. One service man told us we were using the wrong detergent, even though it was the detergent and spot-free rinse that came with it. Another service man removed the door cover so he could watch to see where it was leaking when it operated. He said the soap was foaming too much and flooding over, so we had to try another brand of soap, even though by now we had accumulated three other brands that were just barely used. The service men never did fix the problem. It took much experimentation from my wife to stop the leaks, which meant we could only use a fraction of the recommended amount soap. By now we were using so little soap that the dishes always came out dirty. So our choice was mop up a wet floor or have dirty dishes every time. Most of the time now we wash the dishes in the sink. One service man said in Maytags effort to make the dishwashers more efficient, and less expensive to build that the motor and pump were way under powered, and everything was made from petro-chemical by-products (cheap plastic) and that we should invest in the extended warranty. Its cheaper than paying service calls when the warranty runs out soon. What we should have done was exchanged it for another brand. My wife said had she only known, we would have never replaced the old Thermador which will be my next dishwasher. As for the micro-wave there are many things I dislike about it especially the rectangle glass tray which is extremely awkward to remove and replace each time you have to clean out crumbs and spills which happen often. The timer on/off bell is way too quiet with no volume control. The message and operation display is difficult to understand. And to top it off the cheap plastic handle broke one week after the warranty ran out which I found out that its less expensive to buy a whole new door than pay for parts and a service call to repair handle. Maytags track record made me not want to deal with service dept. again. I will probably be money ahead to trash the two appliances, start over and do some homework and maybe buy a European made appliance. I know German technology is not all about profit making, but quality, reliability, durability. I hate to sound un-American but greed in American corporations will be their downfall.

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

I purchased a Maytag Dishwasher at $600. 6 months after installation, the control panel quit. Maytag sent a repairman and replaced the panel. 4 months later, the control panel quit again. The repair man told me that if it failed a third time, that Maytag would replace the dishwasher all together. The control panel quit again just a few days before the warranty expired. When the Maytag repairman came for the repair, he tried to convince me that it was not the control panel this time. He then replaced the control panel, but did not use the embedded electrical connectors. He literally cut the wires and wired it together by hand, wrapping everything in electrical tape. He said this was a different repair than the others and the three strikes and a full replacement rule didnt apply. I wasnt convinced and called Maytag to complain. I was promised a six month warranty extension, if I would accept the repairs. Two months later and the control panel has quit again. When I complained to Maytag, I was told that I had no six-month warranty extension and it had never been promised to me. They offered to send a repairman to diagnose the problem for $130. Needless to say, there will NEVER, and I repeat NEVER, be another Maytag appliance bought for my home.

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

I bought the bravo 2 1/2 years ago. It started making loud banging noises during the cycle. I constantly had to rebalance my load. Then it stopped spinning at the end of the cycle or it would leave clothes wet. We had a repairman in and he told us that it would cost at least 600.00 for a new computer. Plus labor. Wow!!! I think a washing machine should last longer than that. Maytag should have a recall on this machine as I have read so many complaints about it.

I bought a Maytag dishwasher from Home Depot in February 2012, $700. After a few months, the buttons stopped working and the machine was unresponsive. I called Home Depot and they fixed it under the warranty. This continued to happen every 2-3 months. After a year of dealing with this, the warranty expired and I had to purchase the manufacturer extended warranty with Maytag, $240 for 5-years of coverage. The problem continued, and every few months, the thing would stop working and I would have to call for service - 2 to 4 weeks without a dishwasher waiting for service appointment then parts and another appointment for the repair.Perhaps my machine was just a lemon. I dont think they make that model anymore. Heres the number so that you can avoid a three year headache of a machine, MD87749 AWM2. I will say that after MANY agonizing phone calls with warranty company, after 2 years of ongoing service calls, they eventually issued me a check to replace my lemon.

Maytag Glass top model #MER8600DHO. I bought it because it got good consumer reviews. This is supposed to be a self clean oven but the steam system in this model is not very effective. It doesnt clean the oven. Would never buy a range again with this oven cleaning system. I wanted to try a glass top stove but wish I hadnt. It is harder to clean and the glass scratches. I really dont like the self clean oven system in this stove - it flat out doesnt work and it takes a lot of elbow grease to clean the oven. The oven however seems true to temperature and does a good job. Overall I am Ok with this stove but wouldnt purchase a glass top again.

This is the most horrible washer ever. Within 3 months it would not go beyond sensing mode and never fill or wash. Tech came and fixed it... 3 times. It still happens and I have to jiggle it all around to activate it. Clothes are never clean, dog hair is never washed out... My broken old agitator machine was taken to the dump & I wish I had it back! How do the stores give this machine a good rating?? I cant do light quick washes, I have to wait forever... Our water bill is 2x higher than ever because if I dont fill the tub with deep water, the clothes dont even all get wet. Hate, hate, hate this thing.

I really like the refrigerator. Its easy to maneuver and frost-free, but I should have gotten the side by side. Also, make sure of your family size before you make final decision. Other than the size I would recommend to family and friends to purchase.

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

The washer does not wash properly at all. There is not enough water. The clothes come out covered in lint and still soiled. MOD: MVWX655DWI, SER: C63142093. DO NOT PURCHASE THIS PRODUCT unless you want a ton of frustration!

I bought a Maytag washer January 2016. We recently had a issue with it so I logged onto the Maytag website and found a service provider to come see what was wrong. I had to pay a $100 fee for them to come out and look at it. I was told that the transition went bad. The parts were under warranty however I would have to pay for labor, which would be $325. Called Maytag and was told because I did not purchase an extended warranty there was nothing they could do about the labor. I can buy a new washer for $500 why would I spend $325 to fix? Already lost a $100 for them to come out to tell me what was wrong. Completely not right. A washer should last more then 4 years! Do not buy any Maytag produces. Will not last!

I bought a Maytag dishwasher, stove and refrigerator and the dishwasher was a problem from the beginning. Repaired out twice and replaced the control panel. Seasonal residence, so the start of year 2 (this week) the control panel goes a third time. Its going to cost $387 to repair (told my elderly mother) and it turns out it was a warranty program that she purchased, not a repair estimate. She was misled as she called Maytag and they transferred her to a warranty company, and once again Maytag says theres nothing they will do. Now, Im hassled with cancelling that as well. I called Maytag and they dont stand behind their lemon of a product and said there is nothing they can do because its out of warranty (even though theyve been out twice to fix it). Do not buy a Maytag product. This is the first complaint Ive every written and I am just shocked that Maytag doesnt stand behind their product. Im informing 100s of people to not purchase Maytag and they will pass along my negative experience as well, for that, I am sure.

The washer drum fills up with very little water, very little. I can do an entire load of laundry and the stuff on top doesnt ever get wet. Went on Spring Break in Florida and a month later our clothes still smell like the beach. Grill out, and I smell steaks the next time I put on the shirt. Stain your clothes in any way, its there forever unless you hand wash it first.To get it to work at all, each time I have to start the wash cycle (I leave the soap out just to save it for the next start), let the drum fill with water, pause it, get all the clothes wet, then cancel the cycle. After it drains and the machine is off and full of wet clothes, then start it all over again adding soap this time. On the second try, set at deep cycle, it will add enough water to cover the clothes - Im guessing because it senses more clothes because the clothes are now wet from the first, cancelled cycle. During the wash cycle, Ill open the lid and robustly move everything around, almost hand washing. #Handy. The dryer is fine, Im keeping it. The washer, cant return it - been three months of this frustration (kept believing it was me, reset it multiple times, change the settings, tried everything). Im buying a new one and throwing this junk out. $700 lesson.

My husband and I bought a Bravo XL washer in the fall of 2015. I certainly wish we had read the reviews on this site of this product. We would have saved ourselves a lot of money and grief. This machine does not clean clothes and actually damages them during the spin cycle as reported by others. This low water no agitator technology does not work on a top loader. Stuff doesnt come clean! Im not sure what we are going to do but we learned a valuable lesson the hard way. We purchased this machine in September of 2015 and are unhappy with it!

We purchased a wall oven model MEW7530DE 11/8/2014 which was installed the first part of December 2014. From the beginning the temp was not constant and everything baked was either burned or under baked. The first repairman said the control panel was faulty and was replaced four months after purchase, the problem continued. After three more repairmen all from different companies concluded they could find no problem and thats just how ovens work now. We contacted the owner of Hamiltons Appliance, where the oven was purchased, and requested a replacement oven which was accomplished December 2015.New oven, same problem, very disappointing. My wife has been baking for over 50 years and has never experienced problems and frustration on this level. The condition of the oven is totally unacceptable and with all the effort by us and others we are at a loss. We purchased an extended warranty which has resulted not fixing of the problem. We hired an electrician to inspect the wiring in case that was the problem, costing us $200. The wiring was all good. What do we do next and what are our options short of another new oven. WHAT IS MAYTAGS RESPONSIBILITY? Respectfully, a very unhappy customer.

I am very dissatisfied with this Maytag Gemini oven Ive had it for 4yrs. It has been in the shop twice for the same problem. Temperature control. It is down again for the same thing temperature control. The repairman, who I had to look at it, says the bill will be over $500.00. I paid $1300.00 for this stove. I cant afford to put any more money in this stove. I had to pay $100.00 for repairman to tell me this. The model # met8665xw02 serial#D30522404. Is there a recall on this stove? There should be. I sold Maytag products for several years at Circuit City. I always pushed Maytag instead of another brand. I believed in Maytag. The repairman hasnt been lonely to me.

We bought a Bravos washer 13 months ago and its been problem after problem. We had 6 service calls and the problems continue. From bearings being replaced to sensors to error codes, and now the washer drips water. This is the worst washer I ever owned.

The new technology on the washers is useless and saves no energy or water. People figure out how to get more water in the tub and use that setting. There is not small or medium water fill anymore.

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

Bravos XL was costly. Mistake! I owned my first Maytag for 20 plus years. The sticker shock of buying a new Maytag 4 years ago was pushed aside knowing how long my previous model lasted. The salesperson at Lowes closed the deal with his explanation of an improved gear driven system vs the old belt and pulley version. Oh how wrong! I too have the jet plane from hell landing in my home for over 2 years now everytime the spin cycle engages. This is a two person family and it failed at 2 years?!?!?As for water conservation... if I dont include the additional rinse cycle, my clothes dont get clean. Watched the YouTube on how to repair this unit... but what guarantee do I have that it wont go back to the same problem in another year? Cant afford another big investment like this now that I am retired, so I will run this baby until it seizes up. Dont wash clothes if company is coming or if you want to enjoy evening TV programs. Not sure why this unit hasnt been recalled based on all the complaints I have read on this site?? Worst decision I ever made! I bet the Maytag Repairman is spinning in his grave!

Dark clothes are left with residue on them, have to run another rinse cycle to get them clean. Been having this problem since we first got the machine. Anyone else having this problem or got a solution to fix it?

Purchased a Maytag refrigerator in July 2011. The compressor failed May of 2013. After many phone calls to Maytag they replaced the parts (compressor) - my cost for labor (aprox $300.00). 30 days later, the service company had to repair a leak and recharge the system. March of 2015 the compressor failed again. Have spoken to Maytag (case # **) - they will provide no help what so ever. I was told I should have purchased an extended warranty.

We had a Whirlpool dishwasher for 24 years, and when it was time to purchase a new one, I did a lot of research before choosing our Maytag. Reviews by other consumers who had purchased dishwashers was very helpful in making our decision, and we have had no problems in the almost 18 months that we have had this dishwasher. It is very quiet. It washes and dries the dishes with no streaks, although I wash off the dishes before loading them. It provides 5 cycles and 4 options and lights blink, when the washing and drying cycles are complete. I would recommend the Maytag, Model #MDB4949SHBO wholeheartedly.

If you are looking for the Maytag repairman he will be at my house Tues fixing my barely 1 yrs old dishwasher. This is ridiculous to pay this amount of money for the reputation that Maytag is known for or I will say was known for. $270.00 for a control panel. My last Maytag lasted over 30 yrs. Not made in the US - not built to last and this was told to me by the people that installed it so take it for what its worth. Look elsewhere. My last Maytag product.

I renovated my kitchen 3 years ago. I decided on purchasing new appliances which included refrigerator, dishwasher, microwave, range, washer and dryer, all of which I got from Maytag. Of course they were always known for dependability but apparently they were not! What happened to this American product? In the last 3 years, I have had my refrigerator (**) serviced 4 times for the same problem. Each time servicing has been a nightmare at the hands of AE service, Preway service and of course at the helm of my nightmare Maytag Customer service. The first mistake I made was purchasing Maytag products followed by the second mistake of purchasing Maytag service contracts. I now have a refrigerator that is not working, waiting on parts since end of august. When I called Maytag customer service, they confirmed the parts were not available and recommended I go online and try to find the part! This added insult to injury. Today, Preway service finally came to install my parts and upon technician’s arrival he opens the part box and realizes he ordered an ice tray cover, when he should have ordered an Interface Control Board. Maytag continues to have their products serviced by incompetent companies and appears to have no interest in keeping you as a customer after you purchase, whatever happen to the dependable people?Maytag had built their reputation on reliable products and dependable service, what happened to this American Made appliance? Here is a prime example of what happened, and why companies like LG and Samsung are gaining more and more customers every day. The best advice I can give someone is avoid Maytag. By the way, I forgot to mention I have 2 small children ages 3 and 4 and Maytag is not concerned about how I would provide food for them with a refrigerator that does not work. Shame! This is not what I expected from what I thought was a reliable company.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

The Maytag Bravos XL low water washing machine is very disappointing. About 20% of the time it needs a second rinse because there isnt enough water released to rinse clothing. Forget washing anything large. It just doesnt do it. Waste of money. The matching dryer is just fine - no complaints.

I purchased my Maytag Bravos washing machine set in July 2007. In May 2011, I had to have the shocks and another part relating to running a balanced load replaced. I spent about $500 on those repairs. The parts to replace the shocks took more than 6 weeks to arrive! Roughly one year later, the plastic water pump has broken and needs replacing - another $100 part plus labor. I always believed Maytag was a reputable company, but I am very sad at the quality of the product I purchased based on their reputation. They should be ashamed! To date, the dryer has been good - knock on wood!

I bought a Maytag Bravos washing machine from Lowes in Ocala in Feb 2017. It broke in March 2017. I was referred to a company called Fields Appliance in Orlando Fl. I scheduled a repair under warranty last Friday between 1-4 pm. No one showed up. No one called. I called and called and nothing. BEWARE.

Gas double oven - range that has performed well over 12 years old with only one service call for thermostat. Very inexpensive to repair and parts are readily available. Easily cleaned inside and out.

I purchased a Maytag Washer Model MVWB765FW in April 2017. Its transmission has failed, makes lot of noise. The cost to repair is about $500. for Parts and Labor, under the 10 year Limited Warranty, as advised by Factory Service. I am better off buying a new Washer for that cost. The days of Maytag reliability are gone. I would not recommend this product to anybody.

I am retired and have always had dogs in my life. My recent purchase of a new Maytag top loading washer has been very frustrating. There is barely enough water to measure in an oversize tub. The placard on the lid, and in the owner manual clearly show three levels of water. Each load takes twice the time as I am used to with my older Kenmore washer. I am forced to cut my loads in two or three, and use more water and energy to do a job that used to take less than half the time, water and electricity. I have had warranty repair to replace the control board twice, but nothing has changed. The repair techs both said there is one program on new washers, the knobs and settings do nothing, and recommended I get used to it. They explained the EPA is responsible for all changes to Protect consumers from harm. WHAT???I wish I had never bought this unit - if I could get my Kenmore back I would, in a hot minute! What a waste of a large tub to properly wash pet bedding and bedspreads/pillows, when there is only 3-4 inches of water! I wasted an entire paycheck, when I could have gotten my other unit repaired or rebuilt. I am seriously frustrated, I am searching for an older washer unit to get back to doing my laundry without being forced into a laundromat for pet bedding and larger items!!!

Bought mdb7609aww2 dishwasher in 2010. Now I cant use it as it will not start even though the panel lights of my selected wash cycle work. I looked up on internet how to reset it, but I only get a half cycle. Called customer service and for $269, I can get it fixed and get a one-year warranty. Wow, what a deal. Might as well get a new dishwasher. Joining the lawsuit. It is about time corporations take responsibility for defective merchandise, not make money to correct their mistakes by charging customers for overpriced parts and stupid worthless warranties. A pox on them.

I bought the Maytag Bravo XL washer and dryer several years ago after reading many reviews. I like the glass top of the washing machine and the front door glass on the dryer. The dryer is fine its the washing machine that does not perform like the old machines. Whoever came up with the bright idea of saving water by cutting down the volume in your machine to about 6 inches for a good size load probably have never used a washing machine in their life. It does not get your clothes clean and does not get the soap out of a clothing to my satisfaction. Who made this suggestion? Could it be the same branch of government that made everybody use those spiral light bulbs years ago? The fluorescence that give off loads of EMF?

We have had this washer for 1 year. I noticed right away my clothes would come out extremely wrinkled. Now not only are they wrinkled, they also smell musty. After researching I find others have the same issue, even finding a video of horrible mold under the drum. We called to have it serviced since we have a 5-year warranty. The service man recommended using Afresh. WELL, we do faithfully every month. He said they would not pay to have it cleaned, and even if he cleaned it, that the mold would come back. This to me is a major design flaw, one that could potentially make people sick. IF there is that much mold growing in the machine, with no way of cleaning it, and now the clothes are smelling, there is a HUGE issue!

I bought Maytag Bravos X in 2014. I bought a set. The dryer is fine. Right after the warranty was up the washer started having problems. Maytag was no help. One sensor after another went bad. Now I have to unplug it to get it to start and then again to get it to spin. It hasnt spun on its own since 2015. It just recently wont start on its own. I have appliance repair people out and they cant fix it. They say everyone has problems with them. My mother swore by Maytags and had a set for twenty years or so, but now they are garbage.

This Bravos 300 washer has never cleaned clothes adequately. I have 3 sons who are athletic and this washer does not clean sweaty or dirty clothes even with extra rinse. Now my machine is 4 years and 3 months old and it needs a new bearing which will cost me $385. The repairman said this is a common repair in this machine. Maytag should be ashamed of the poor quality of this machine. I am now looking to by a new traditional top loader. These HE machines are a joke. I am contacting them to make a complaint and see if anything can be done.

Maytag WASHING MACHINE MVWC200XW - Will not clean our clothing. We have been tolerant of Maytags disregard for the people who have trusted their product and name over many years. No longer will we purchase a new Maytag or Whirlpool product. They say third time is the charm but I can not afford to take the chance. I wish them luck, they will need it.

I am online now because we have the same problem. Our refrigerator is less than 2 years old. Watched a video on YouTube how to fix problem and repairman said engineers who created design must have been on drugs. I think hes right. Very common problem. Have to call repairman!!

My Maytag washer is only three years old and the control panel completely went. Not only did it cost me the service call, they want $360 to replace the control panel. I called Maytag/Whirlpool to see if they would help with the cost of the part. I am 60 years old and the only one who uses the washing machine. It is not beat up. Maytag would not offer any solution at all and refused to even pay for any part of the control panel. They said it was really my tough luck for not having bought the extended warranty. When you spend so much for an appliance, you do not expect it to only last three years and you should not need an extended warranty. I am so disappointed and I will never buy a Maytag or anything from its parent company Whirlpool.

Bought washer in 2010 from Sears. Told me the washer had a sensor to measure how much water it needs. Was told by service guy that was a blatant misrepresentation by the sales person. It only fills up with 8 of water. When I wash my white towels with normal dirt (dog paws), with HE detergent and bleach on various cycles, my towels come out tie-dyed with dirt. Totally dislike this machine.

We purchased a refrigerator in December 2010 with a 12-month warranty. Since the refrigerator was delivered, we have experienced nothing but problems. Most recently, there was a problem with the auto defrost causing us to lose all our food stored. It also caused water damage to our floor. We scheduled maintenance with a contracted company through MayTag. After three scheduled visits, which made me miss 3 and a half days of work resulting in an additional loss of over $300, our refrigerator is still broken and they just want us to schedule another maintenance visit. When calling Maytag customer service we are literally told, “your loss, there is nothing we can do to resolve your issue, we can only continue to send out maintenance.” I am so disappointed in this company, the product, the customer service, maintenance service etc.

Due to our previous washer breaking down, we had to purchase a new washer. We have always been loyal to Maytag since we were always pleased and satisfied with the performance. However, this new washer does not deliver in performance, cleanliness, energy savings when cycles take much longer and you end up maybe not using as much water, but our electric bill has gone up considerably. I have nothing good to report about this washer. We purchased it back in April of 2013, and Ive given it the benefit of the doubt by experimenting with all the different wash cycles. I am just not happy with it. I so want to trade it in for a front loader and give Maytag one more chance.

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

I purchased a Maytag electric dryer Bravo 300 Series in November 2009. December 2011, the main computer board went out and had to be replaced. Do not purchase Maytag appliances. They do not stand by their defective products. First and last Maytag purchase.

I have had nothing but headaches with our washer. We purchased it 4 years ago and after using it for a few months, I took it out because our clothes came out smelly and unclean. Called Maytag and they did nothing. So we went back to a regular washing machine and put this machine in the corner of the basement. I refused to throw away a $1,100.00 machine! So this year our machine quit, so we decided to try using the machine again to save us some money instead of buying another one... Well, that lasted for only a short time. Clothes still smell, came out unclean and just yesterday, the machine stopped rinsing and spinning! This machine has barely been used and its been nothing but trouble. Maytag service just plain sucks. They dont care about their consumers. I will never buy a Maytag again and I always let everyone I know to not buy this type of machine.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

I chose Maytag because they received a good rating from Consumer Reports. I liked that they were for extra large loads however now that Ive had them for 12 years I know the large loads are no more than my old Kenmore washer and dryer. The real deal breaker for me is the size of load that you can actually wash. I was hoping I would be able to wash a blanket without worrying about the washer going off balance. My washer and dryer are Maytag although I dont know the model number. They are full size but the extra large load is not extra large. The knob on my washer broke and Maytag wanted $15 for a plastic knob! I found it on eBay for $3. The washer goes off balance too easily.

We have owned a number of dishwashers, some cost a great deal and some were inexpensive. Our current dishwasher is a Maytag and it has proven itself to be the best dishwasher we have ever owned, not only is it quiet, it cost less to operate and cleans all dishes and utensils excellently.

I purchased a new Maytag washer (Model# MVWC565FWO) from LOWES 18 months ago and the paint is bubbling on the inside of the door. Neither Lowes nor Maytag would do a thing. We have spend many $1000s at Lowes and considering the replacement cost is only $126 for a new door I can see Lowes following Sears for their lack of customer service and diplomacy in matters like these.

Maytag dishwasher #MDB 9750AWQ - I am now on the fourth control panel and in less than one year, the present one is starting to fail. The third one failed in less than a year also! I have read the reports of others and apparently, this is not just my dishwasher. Maytag owes its customers a recall of this inferior machine.

It had always been my wish to own a Maytag washer and dryer as they were considered THE BEST! Well was I wrong!! I am on the third stainless steel drum, this one has a hole in it, need 4 wheels and pulleys, with service $542.61!!! On the average, I am having a service call every 6 months - last year we were gone for 6 months so no laundry was done, one drum was delivered and was egg-shaped. Maytag has been NO HELP! I am very disappointed with Maytag, their service and product. They HAD an excellent reputation, to me that is everything. Quality, customer service, and their word means nothing to me anymore.

I called Maytags customer service about an over the range microwave that was bought 2 years ago and barely used. The mechanism in the microwave on the latch for the door, clicked into the body of the unit and therefore the door does not register closed which doesnt allow it to come on. After explaining this issue to the customer service rep, she insisted that the only thing that Maytag would stand behind was the part if needed. A service call would be between $100 - $150. The microwave isnt even that old and why would Maytag not stand behind a like new unit? I bought 3 Maytag products and I am now regretting it. I had asked to speak to a supervisor and she just proceeded to repeat the same thing the sales rep did. They will only cover the cheap part if needed.What happened to Maytag being top of the line? Apparently they dont care about standing behind their products and would rather you buy an expensive extended warranty to cover their cheaply made appliance. I think they should be under review as a company. I would somewhat understand paying if my appliance was 5 to 10 years old. But its basically new. How is there no protection for customers when it comes to purchasing lemons from an appliance dealer? I will NEVER buy Maytag again and plan on selling my 2 other newly purchased appliances before they have issues. Maytags reviews on social media are terrible. All they offer are the words Im sorry and I understand your frustration. I assume thats just what they have written down in front of them to tell everyone who calls with issues. How do you not stand behind your products! I wish I could select no stars vs the 1.

I bought a brand new refrigerator and about four months into using it, the freezer door began to become loose and opened by itself automatically. It also started to leak so I called the company continuously looking for a solution. However, they never resolved my problem. The company sent a technician. However he was unable to fix the problem. The technician said it was fine and did absolutely nothing. And now I am still waiting, but now your company says my warranty is up EVEN THOUGH I called much earlier and your company did NOTHING to help me. I need someone who can handle my problem. Ive been using your products for many years, and have always been satisfied by it. But this refrigerator has changed my perspective. I hope you give this a peace of mind and treat your other customers better.

Faulty control board. Have owned a Maytag dishwasher model MDB6769PASI for 2.5 years. The unit started beeping at random times for about a week - then went dead! Sounds like other reported failures and it is unlikely repairs will be permanent! Never again Maytag.

I purchase a Maytag dishwasher from Home Depot on 12/31/11. Based on the their commercials, I thought they were dependable. I did purchase an extended warranty, as I always do with any new appliance. After 2 years, the dishwasher stop working. I contact Home Depot and the extended warranty and was told to contact the manufacturer. Maytag blamed the extended warranty for the problem. They told me they could not help me. And could not help me. I will never ever buy any appliances from Maytag again. This model is M936/110V cord.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

Omg I am so shocked at all the complaints about these refrigerators.. I too bought refrigerator, stove, microwave, dishwasher from Lowes after a storm just about destroyed our home. I was so excited to have such a beautiful refrigerator and new kitchen...but shortly after it started freezing on the bottom of freezer and leaking all over. My new floors and kitchen cabinet are ruined. Every other day we have to break up ice and clean it out from freezer.. it still then leaks.. several family members have slipped and hurt themselves. Please if anyone knows how to get it fixed without it costing us a fortune let us know. Maytag (Whirlpool) knows it is a defect... Why will they not fix it? I cant afford a new refrigerator and shouldnt have to after only two years.. If a class action comes up.. please contact me. Shame on them...

On my 3rd circuit board for a MDB7749SBMO MODEL dish washer. The people at Maytag are people that wont even talk to you about it. How many people have to complain before theres a recall on a faulty ribbon cable.

We purchased the Maytag Bravos MCT in July 2017. Just passed the 1 year warranty and the glass door just shattered. No reason for it really other than it must have been defective. Nothing dropped on it and it wasnt cold or hot in the room. I got nothing. Maytag said they didnt know why it would happen, and would have to send service tech out. A lid for this type of washer alone is $200-$300. Buyer beware. Dont get a glass top loader.

I purchased a Maytag Centennial Top Load Washer in February 2012. I wish I had understood the workings of the washer before making the purchase. I am not at all happy that the lid locks as soon as the washer starts and unless I push a button to get the lid open. I cannot open the lid to maybe add more items or check to see if the water amount is sufficient or too much. I have no idea how much goes in for each water level. Of course, I cannot take water out but I could put more in if I see it is not enough. And after learning the water levels, I would know just how to determine the level I need. Some man must have designed the panel. Otherwise I am satisfied. I really like the large load capacity. I originally thought I wanted a front load to get a large capacity but this suits me fine.

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

I also have a Maytag Quiet Series 300 dishwasher. The front panel has stopped working. It was a horrible dishwasher from the beginning. The dishes were streaky on the top rack. And I had to replace the rollers after just over a year. The upper rack has rust on it. The Maytag double ovens I bought at the same time had to be replaced within a year, as the racks damaged the porcelain interior. I also wish I had found your site before my purchases. My husband is not working now. So, I guess we will be washing dishes the old fashioned way.

Dont buy this machine. Although it is an HE machine and supposed to save on water, it does not give enough water to at least cover the clothes. I had repair come in and they changed the computer but no improvement. The cycles determine the water amounts not the type of clothes you are washing. So if I only a few things I use cold water wash, if I have a half load I use deep water wash and have to add water to it. Its ridiculous. Do yourself a favor and get an LG. I wish I had.

We bought MDB7759AWB Maytag dishwasher in 2011. It worked decently until now when it stopped delivering water to the upper rack. The cleaning quality on the lower rack also dropped significantly although it might be due to the lack of water delivery to the upper rack. Apparently there is something wrong with the internal pump. The Maytag service offered a repair for $300+ which I rejected because this is a ridiculous cost and I would rather buy a different dishwasher. My conclusion is that if you buy Maytag dishwasher you need to factor about $300+ for the repair(s) in 5 years as apparently they do when they sell you this product. Anyway, even though Maytag was a decent brand a long time ago (probably in the past century), it is not reliable anymore. It does not mean it has to be much worse than many others but if you are looking for something better than those others I would not recommend Maytag.

Purchased the Maytag Bravos washer approx. 2.5 years ago. I cannot even begin to describe how disgusted I am with this washer. My clothes i.e. towels come out ripped on the edges, clothes do not get clean, shirts etc come out wrinkled no matter what setting used. It is not energy efficient because loads of laundry need to be washed twice if they are soiled (like our everyday jeans). Went back to the independent store where I purchased washer and was told to use only the bulky or gentle/delicates cycles to reduce rips in clothing. Such a complete waste of money, and it was not cheap!

Maytag Washer and Dryer XL Bravos - The worst machines ever. I have had many washers and dryers and every one of them were good enough to get my clothes clean and dry without wrinkles. This washer Maytag Bravos Washer and Dryerdoes not clean clothes no matter which setting it is on. The dryer does not dry the clothes without wrinkles if it dries them at all. They are only about 6 months old, I have followed the book on usage and it still doesnt help. If I could pick these up and put them at the curb I would. If Maytag would take them back I would return them. Buyer beware.Updated on 03/17/2018: Maytag wrote to me and wanted me to give them my contact information along with any other info regarding their appliances. Still havent heard from them, and I assume if I do it will be like all of the other replies, Sorry for your inconvenience yada, yada, yada. I did check online for Lemon laws for appliances and there are laws for the consumers to fight the companies. If and when they contact me I will be sure to mention this to them for what its worth. I think a class action suit might be the answer for all of us consumers. If banding together would help count me in!!!

Maytag Dryer- Bravos XL - Waiting for my third service call since purchasing my dryer less than 2 months ago. After 2 service calls the repairman found a piece of the mold that should have been removed at the factory causing problems. Now, my dryer made a weird noise, sparks flew and it no longer works. After calling the seller and the manufacturer requesting a replacement, they feel it should be repaired (again).

Re: refrigerator model # MBF2258XEB1. The above-referenced refrigerator was purchased in 2011 from Home Depot. We paid over $1,000.00 thinking we were buying a good product. Right now the bottom freezer is working but the refrigerator is not cooling. An appliance repairman cleaned out the defroster part, but that did not resolve the problem. He said it was a compressor/valve gas line problem. I cannot afford to spend hundreds of dollars to have this repaired. Even though the warranty has expired, I believe that Maytag should pay the cost of the repair. This is VERY inconvenient and frustrating.

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

I bought the Maytag because of its reputation and as a washer it hasnt disappointed me.. It gets my clothes clean with a minimum amount of effort on my part and it doesnt use a lot of water... I love my washer.

Because of the power of advertising, we replaced every appliance in our home in 2005 with Maytags. Since then, weve had minor problems with the stove and dryer, many problems with the dishwasher and washing machine, and complete failure of two Maytag microwaves, the last one was only two years old. The washing machine failures resulted in major flood damage two separate times due to two separate failures. Our refrigerator, model MBB2256GEW, has yet to let us down, however, since new it makes loud snapping noises that wake us up at night. It sounds like someone banging two large sticks together. Fortunately, I can repair most of these issues when they arise, but Id much rather get some rest like the Maytag repair man...

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

Clothes are never submerged in water. Clothes come out worse than when they went in. Every review and complaint mentioned is dead on! This Bravos XL is a piece of crap. Stay away from lying salesmen from HH Gregg. And stay away from Maytag. Perhaps we should all get together and file a class action lawsuit! And donate all monies, washing machines and dingy clothes to charity!

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

My Bravos Washer and Gas dryer are only a few years old, and they have both been problematic to say the least! Neither Home Depot nor Maytag have been helpful. My washer has had the shocks replaced already, because it would constantly go off balance and shut down and they cant grease the bearings because they are sealed. So, now it sounds like an airport is in my laundry room! The gas dryer takes an entire day to half dry a load and its burnt on the inside!

We purchased a Maytag Bravos Automatic Washer 6/28/09. The interior enamel around the bleach dispenser started rusting about six months ago and it’s getting worse. Our white clothes are getting rust stains on them. Otherwise the machine works well, but what a huge flaw. We will buy a new machine, but not a Maytag.

Ice maker flaps open and closed and lights flash. Bought brand new lasted a couple years. Lots of people are having the same issue according to internet and nothing is being done by Maytag to help except offer repair at half the cost of new fridge! Junk!!

Maytag washer not draining properly. Called Aug 15 for help. First tech in on August 23, makes a diagnosis, orders part; no news, I call, am given Sep 15 as next date. Come 9/15, I take off from work, only to find out tech cannot come that day, to reschedule. Next tech comes 9/25 with a different diagnosis and different part to order. By October 3, an announcement that part came in, to make an appointment. By now, its been a month and a half, I am so angry. I call a friend, who fixes it in 15 minutes by simply clearing a clogged drain filter. This is unacceptable: the inordinate wait, incompetent techs, unresponsiveness from customer service. I cancelled my contract with Maytag Warranty/AIG.

We bought our Maytag washer and dryer a bit over 5 years ago. Now the UL warning comes on. Found out it will be over $400 to fix it. It only cost $500 new. Repairman says it is very common and not to pay him to fix it. Our GE went 20 years. Lesson learned, wife is out looking at new GE.

When I attempted to contact Maytag about an issue in my 3 month old washer all I received is an automated email back saying to contact one of the repair places on their website. There was one, so I notified Maytag I would contact them. I contacted them. They said Maytag had not notified them that this was a warranty repair and if I wanted them to come out I would have to pay for it. I have attempted to contact Maytag several times to get this straight. Guess they are trying to wait out the warranty to respond. Will NOT EVER buy another Maytag. Too bad they used to be a good product.

About 4 years we purchased a dishwasher model # MDB7749AWM2 made by Maytag.The first part of Aug. 2015 it quit working. I had a repairman look at it and he said it was the control panel and he would order one. He ordered it and we waited a couple of weeks, no part. He called about it and they told him Sept. 9th it would be sent. Sept. 9 came went and no part. He called them again and they told him they had no record of the order. So he ordered it again in few weeks, was told it was back-ordered. This happened a couple more times and I told him to cancel the order. I would go buy a new one but not a Maytag.