I purchased a Maytag Electric Range (Model: MER7662WS1) at Lowes in February 2011. After few months, we found many rusty areas on the stainless oven door and on the stainless drawer.On 9/8, I called Maytag at 1-800-688-9900 to complain that stainless steel is not supposed to rust. A representative took the initiative to schedule A&E Factory Service to come to my house for a warranty repair, and assigned me an order # 40629499. I did not request for this service call and naturally, I regard this as a warranty service or a service of quality check of a product.On 9/19, a technician came to check the rusty area and confirmed that the stainless steel have rusted and the rust will eat through the panel. The technician called Maytag, and got the answer that Maytag will not pay for his visit because its not under warranty. The technician then checked the warranty manual, but could find not any statement that neither rust is cosmetic nor rust is not covered. The technician asked me to pay $132 for his five-minute checking service. I was so upset and called Denice at A&E Factory Service at 1-800-905-9505 to bill Maytag directly. She ignored my request and said that I should take it to Maytag.After a couple of hours waiting, holding and transferring, I explained to two Maytag customer service representatives my problem, only to get a Sorry, its not covered, its cosmetic, reply. I insisted talking to a manager and finally got Melinda at Care Solution Team. She, too, refused to waive the charge for me and claimed herself as a supervisor and decision maker and theres no one above her who could resolve this issue.I emphasized that A&E service call was authorized by Maytag, I did not order the service. Who would have thought that a service authorized by manufacturer is not covered under warranty? Besides, this representative failed to inform me that rust would not be covered, she should have known better. Therefore, I believe that the person who initiated the service call to A&E should be held accountable. But Melinda never wanted to agree with this logic and kept saying, We dont force customer to have home service. You are liable for the bill.She refused to pay for the service and forced me to pay the bill from the mistake they made. She even refused to give out the persons ID # and name of the person who called A&E. She only documented my complaint--whats the point of their documentation? If this is the tactic that Maytag is using to categorize rust as cosmetic (if rust can damage material, then you should not call it cosmetic), and ban customers from claiming the rust damage so they can use poor quality of stainless steel on their appliances to save the cost, then, it is dishonest to advertise that this oven is stainless.A representative even said that Maytag should have emailed me with the confirmation of service call and noted that its a non-warranty service. Also, A&E should have informed me before arrival that the service is not covered. All these were not true. First, I did not receive such email from Maytag or Whirlpool. If Maytag would have warned me with non-covered policy such as this, they should have the courtesy to call me in case the email was unreliably routed to spam box. A&E only informed me that they are coming the next day, but no such thing as telling me that the service will not be covered. Even their technician did not know about the non-covered issue, and had to call Maytag today to find out.Had the person who scheduled the service told me that the rust on the stainless panels is not covered under warranty, will I still allow the service call and agree to pay $132 for a five-minute checkup and watch the technician leave without performing any repair? I asked Melinda to let me talk to her supervisor but she said that theres no one who can talk to me, and the only way to appeal is to write to the companys executives. The address is: Whirlpool Corporate Office553 Benson Rd Benton Harbor, Michigan 49022. I doubt that an appeal will help me at all. I will take this matter to small claim court, I wont let them force me to pay the bill when I am not at fault.

I had a stove my mom bought for me 26 years ago. Still worked perfect. Used constantly. In 2018 my husband had to have this stove. Said no my stove my mom bought and still works perfect sentimental plus three children using it. Not one problem. So he buys this Maytag stove I didn’t like but don’t cook much warming things up or frozen pizza. Go to our sons for holidays. Always next day cook a turkey for sandwiches. Open the door which is too heavy. Wouldn’t close and called my husband. Got it semi closed. Said we’re not eating it. He proceeds to cook. Door opened. More turkey is in garbage. My husband started reading. I also did. Looks like these Maytag stoves are garbage. Make a lot of money for repairs. Now this goes to dump. No one stands behind their products. Is it worth paying to repair no.

If I can rate the AquaLift Technology oven cleaning system that my Maytag oven has as a “Zero”, I would. This technology only removes some of the spills on the bottom of the oven. It does not clean the sides or top of the oven. I’m back to the olden days of using a lot of elbow grease to remove splatters and spills. They say you cannot use any cleaners in the oven either. At least with the old ovens you can spray an oven cleaner and wipe it clean. This product has taken us back before there were spray oven cleaners!

I had my kitchen remodeled less than 4 years ago with a Maytag refrigerator, Bosch dishwasher, and GE stove. I had a 1 year warranty, and purchased additional 2 years. The warranty ran out last year, and the refrigerator is not working. Maytag customer service said all they could offer was 1 year extended warranty for $300. I told them a refrigerator should last longer than 4 years. They agreed, but that is all they did. Ive read other online reviews, and it appears a lot of people are in the same situation (however my fridge is not on a recall list). I will never buy another Maytag product ever! My GE and Bosch appliances are working just fine.

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

Maytag Range Precision Touch Control 800 Electric Smoothtop - The racks in the oven fall down. I have replaced them with new ones but am having the same problem. I emailed my concerns to Maytag a few months ago but didnt get any response (so perhaps I didnt go to the right site). The oven was purchased in early 2008 and this is the only problem I have had with it. If I am extremely careful, I can bake cookies but if I try baking or roasting anything heavy, the racks fall. It is very frustrating but I was pleased, for lack of a better word, to see that someone else was having the same problem - at least I know it isnt just me. I will try contacting Maytag again.

Like so many other consumers, I was drawn to the Maytag name because of what I thought was the high quality of their products and their stellar reputation. So when our old wall-mount oven failed, I sought out a replacement from the Maytag line. I purchased a model MEW5530WDDB17 in 2011 and had it professionally installed. It worked well for a couple of years. Then, suddenly, three of the numbers on the digital control panel stopped working, making it impossible to set the oven to any temperature that included a 4, a 2 or a 5. When I contacted Maytag, I was informed that the unit was out of warranty, but that I could schedule a service call. I had already researched this issue online and knew that the service person would inform me that I needed a new control board and that one could be installed for around $300, and that the new board would come with a 90 day warranty. When I asked the person to whom I was speaking, she said that she had no further information for me. I know that a lot of others have had this same issue with their Maytag range/ovens, and many of them agree with me that we will never purchase another Maytag product.

After 2 years the oven didnt work. I had a repair fix it for $500 but if I wanted the convection to work it would cost another $800. Obviously not worth it. Now the oven needs to be set at 400 if I want then actual temperature to be 350. Now the latest - the racks are too small and falling! I just put my Le Creuset in the oven and the rack fell. Splashed everywhere! This happened at Christmas with my turkey. So bought the fridge - everything in the back freezes. Never ever buying Maytag again. Im guessing the Maytag repairman isnt lonely anymore.

Bought the Maytag model MFI2670XEM and within 6 weeks freezer wasnt making ice. Repairman came and fixed it, within a couple weeks same problem again. It was fixed and within a couple months same problem. Fixed, but makes very little ice. Now 18 months later after purchase freezer is leaking water onto the floor. Very disappointed!!! After reading other Maytag reviews I am worried I will have to dump this relatively new refrigerator and buy another (wont be a Maytag) and our upgraded dishwasher from Maytag is terrible! I hand wash all my dishes before putting them into the dishwasher. The smallest bit of ketchup or sauce is not washed away in the wash cycle. Our Maytag stove/oven seems to not heat correctly, as well. Internal temperature gauge reads 5-15 degrees off all the time. Thumbs down Maytag! Extremely disappointed with Maytag products! Will never buy again!

The range I have works awesome, which is surprising for an electric stove. For being 11 years old I am happy with how it is still holding up. The only thing I would improve is if it was a double oven instead of a single!

Maytag washer, dryer, oven, microwave over-the-range - all crapped out in four years. I will never buy or recommend Maytag. I believed them to be one of the best brands but apparently theyve learned a few too many shortcuts.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

In a way, l feel fortunate and you will read why in a minute. l have been reading Maytag complaints specifically looking to see if what happened to me has happened to others. Apparently, it has. We purchased our Maytag range, model MER57750AB, in 2005. We too have had some repairs done under warranty. Unfortunately, we live in a day and age where technology isnt always our friend. The old appliances that were not electronically driven lasted forever; todays appliances do not. However, when something with potentially serious consequences happens that is not technology related, it rates in the who is the idiot who designed that? category. I am talking about the exploding exterior glass oven doors.Two weeks ago, the oven door handle on our range came unscrewed on one side. I continued using the appliance, planning on repairing it myself when l found the time. (I used to tinker around the garage with my dad when I was little and therefore, I have great repair skills in several areas.) Last week, I was standing in front of the stove when all of a sudden, the glass panel dropped from the door! It landed straight up on the floor and fell forward so the top edge of the glass landed on my toes (the toes that I had surgery on for six hammertoes last November and are still sore!). Needless to say, l was shocked that this happened, and even more so, I was grateful that it did not break or either of my two grandbabies were around at the time. Then, I looked at the glass and saw that it was attached to the door using only eight small pieces of double sided sticky mounting foam. I mean small! As I said before, idiot! Did they not think that the heat from the oven would eventually wear out the ability of the tape to do its job? I gave up reading after I found enough complaints about the mishaps with the glass on the oven doors to realize that there is a definite problem here. I did not see where the glass fell intact, as mine did. Therefore, I am suggesting that the exploding glass panels more than likely gave way, as mine did, and shattered when they hit the floor. Should there be a product recall for this? Absolutely! The question is how does a recall get put in motion? As others have stated, this could have been a horrible disaster had little ones been around. I pray that doesnt happen to anyone.

Major issues with the Aqua Lift Range. Takes forever to preheat the oven, 15-20 minutes to reach 375 f- 400 f. Aqua clean cycle not efficient and does not clean at all. The stove top is impossible to select and keep the heat consistent. When adjusting the heat up or down when you slightly move the dial it overreacts. When moved the heat sways may more than selected. The fridge works well but the bottom drawer is way too flimsy and it wont last a long time as it will crack. This is our first purchase of Maytag appliances and it will be our last. Our old 10-year-old stove worked much better than this one. Sincerely, Russell ** & Linda **, e-mail= **

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

I bought this stove thinking of the Maytag repair man commercial that was advertised on TV for washing machines. Apparently Maytag only knows how to make washing machines (I did not buy one of their washing machines after my experiments with their stove). From day one the oven door never closed right, the self cleaning oven device had to be replaced 3 times over the year after have a repairman tell me that they all fail. I stopped using the self cleaning feature. This stove has cost me so much in repairs. The cook top is very very hard to clean. It always looks dirty. All the plastic knobs have melted off because the oven door never closed right. And the knobs are crazy expensive to replace as is just about everything on this stove. The oven temperature can not be trusted never cooked at the temperature it was set at. I paid a lot of money for this stove 10 years ago. And I am finally able to replace it thanks to a Christmas present from my 3 children. I love to cook and this stove made it difficult. My advice is to look for a different company when buying a kitchen stove. This Maytag has been nothing but trouble for me.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

We were offered a Maytag microwave with our newly built home two years ago. I do not know if it was a good value for the money compared to other brands as I did not price or feature shop for this oven. But the oven has worked well since we moved in.

We bought the Maytag Aqualift cooktop about a year ago & are continuously dissatisfied with it, for several reasons: 1) the cooktop is a huge nuisance to cook on. The burners are either raging hot (causing boil-overs), or too cool to simmer. The boil-overs then require much cleaning with an expensive cleaning agent. 2) the oven, whether you use regular or convection, underheats - so you can’t tell how long the cooking or baking process will take, & you have to monitor the cooking process. 3) the so-called self-clean is a joke; the oven will not be clean unless you crawl inside & clean it manually. Overall, I’d prefer to toss this range in the trash. I’m a good cook, but I get angry every time I use this expensive, poorly- designed product.

I am very dissatisfied with this Maytag Gemini oven Ive had it for 4yrs. It has been in the shop twice for the same problem. Temperature control. It is down again for the same thing temperature control. The repairman, who I had to look at it, says the bill will be over $500.00. I paid $1300.00 for this stove. I cant afford to put any more money in this stove. I had to pay $100.00 for repairman to tell me this. The model # met8665xw02 serial#D30522404. Is there a recall on this stove? There should be. I sold Maytag products for several years at Circuit City. I always pushed Maytag instead of another brand. I believed in Maytag. The repairman hasnt been lonely to me.

I am extremely dissatisfied with the Maytag Gas stove and oven. The setting are too high and you cannot simmer something, it burns. I tried the oven cleaner and my oven is still dirty. The burner knobs do not have a click feature. I came home to a house filled with gas. I was not using the top burners, so I must have brushed up against the burner knob while using the oven. I was only gone an hour, imagine if I had been gone longer and walked in the door and created a spark on the rug.

We bought Maytag dishwasher and Fridge and Whirlpool stove, the dishwasher, front panel came apart, the seal leak, the motor make a serious grinding noise, wheel on the interior racks were broken off easily. All of these parts will not be changed under the extended warranty by King & State, Whirlpool do not want to respond to our request for follow up. Neither is Leons Store where we bought these appliances. Only after 4 years of normal use.... Think about it! Kitchen Aid, Amana, Maytag, Whirlpool, latest Kenmore same products. BBB is not helping resolving these issues, their method is wait and see. Stay away from those companies. As Info: if you need to rinse by hand the dishes before setting them in the dishwasher...wash them much faster and better done.

Like many people here, I have a Maytag Dishwasher Model # MDB7749SBW3 Serial # F40107007. We have had this dishwasher for about 12 months to 18 months. The first indication that there was a problem was some of the lights were acting strange. Then the dishwasher starting going nuts. I removed power from the unit thinking that maybe the controller became confused. The problem persisted. I would hit buttons and either nothing would happen or something completely different would happen.I take the dishwasher door apart and remove the touch pad. I notice some discoloration on the ribbon cable. I remove the glued on front panel to look at the electronics behind it (see pictures) and I see some discoloration there as well. So using my multimeter, I find that there is a direct short between pins 4 and 5. I vigorously flex the cable at the point of discoloration and the short goes away. So at this point, I doubt that I can get just the flexible circuit strip so Im going to have to pop for a new touch pad assembly. I didnt go further in the measurements as there was no point since I already detected one failure. Furthermore, I inspected the computer control unit and I did not see any obvious signs of corrosion or discoloration anywhere on the processor board. So it appears that there is no problem with it.Conclusion: Many people are at a disadvantage when it comes to electronic devices. In my professional opinion, this is clearly a failure of the insulating material of the ribbon cable due to environmental contamination. Visual inspection shows that corrosion of the conductors is clearly evident. About Me: I have been an electronics technician on and off for over 20 years now. I have a 2-year college degree in electronics technology and I am currently in school to become an electrical engineer. In my house, when something breaks, I fix it.

My 2.5 year old hood range microwave stopped heating. I called repair guy, he charged $115.00 for barely a half hour and said he tightened a part and it should be fine OR the part would need to be replaced. Guess what!... That night microwave is still not heating anything. Dinos Appliance Repair is responsible to repair but Maytag doesnt stand behind its product. How do I get my money back when a repair doesnt repair anything? I wont buy Maytag again or GE.

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

We too bought a Maytag range (MER5755QAW) approximately 5 years ago. While making Christmas dinner, it quit working. The oven would not heat. Too bad it had to quit that day (or at all for that matter). Unfortunately, every single appliance I bought for my house 5 years ago is a Maytag appliance! The microwave quit last month and I have yet to replace it. I bought Maytag because for the longest time it was such a positive household brand name. Unfortunately, with 2 appliances less than 5 years old and out of warranty, I will never purchase one of their products again! I will spend the extra money and go with LG especially after reading some of the reviews on here on Maytag’s products (there are over 192 complaints on the Maytag ranges and ovens alone on this one forum).

18 month old range did not shut off although it showed off on the cancel page. $800 down the toilet. Maytag had the guts to charge $100 to troubleshoot plus parts and labor. I will donate it to scrap metal. Company does not give a rats behind. DO NOT BUY MAYTAG.

We purchased a Maytag Gemini gas range last year in April and the extended warranty. The ovens have not worked correctly since we bought it. I never do this type of thing, however, I am just disgusted! I am going to exercise my right as a consumer to express my customer dissatisfaction and share using the social network. I dislike Maytag and even dislike A&E factory service more! I have never experienced such bad service on a new appliance. What is even more concerning and the reason I am posting this warning is there appears to be no recourse! I googled search both companies and the first things that came up were complaint pages. How sad! Buyer beware! If you buy a new appliance, research the warranty provider. It appears that Maytag has laid off the Maytag repairman and went to a lost cost unskilled service provider! A&E repairman has no idea how to fix the oven. He replaced the part. 4 weeks later, came out and walked in the house and did not even look at anything and ordered the same part again. He told us he would be back the following Friday. He did not schedule an appointment. I called on Thursday before he was due to show on Friday and A&E told me I had no appointment scheduled. They told me to inspect the parts that were shipped. I told them I would not even know what I was looking at! They told me the repairman would be back out between 1-5PM on Friday. No one showed. At 2PM, I called and A&E said the repairman must be on his way because he did not call and say he wasnt coming. But again, he did not show! I made no less than 6 calls to A&E and Maytag after that! A&E would not escalate the situation to a supervisor and on call number 6, when I finally got to an advocate, they told me to call Maytag! I have taken 4 days off as vacation to be home for the repairs and this last day was the final straw. When I researched escalating paths for both companies on Google, the first thing that came up was whole pages dedicated to complaints for both companies!

Bought a stove in May of 2014. In July of 2014 we noticed a 1x6 stain inside the glass of the oven door. I called Maytag and they stated only 30 day warranty on cosmetic flaws. I said this was not there when we bought it. They asked if anything had boiled over because if liquids get in the vents on the oven door it can get in between the glass. I stated no, only cleaned with Stainless steel clear. They stated most likely when I sprayed the door it ran down in between the glass. I said that is a flaw. They said, no the vents are there to allow heat out. I asked if they also were designed to let liquids inside the glass, they said no, I said design flaw. They will do nothing. I also pointed out that nowhere in the owners manual is there a reference to this possibly happening. Our sons in laws have a 3 year old LG stainless steel with vents and have never had this problem. Maytag will not stand behind their products even when they are the ones at fault. Buy a different brand.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

I am writing to tell you the dishwasher sold to my family malfunctioned as a result of an apparent design flaw. I also ended up wasting an entire day for a service person who never arrived. On October 14, 2009, my family bought a Maytag Dishwasher (model #MDBH979AWW) from Home Depot. It had run beautifully until last week, when the left-hand side of the control panel went dead. I then called the Maytag service number (800-688-9900) listed in the instruction manual and scheduled an appointment with the A&E Factory Service vendor for the following Friday (July 6th, 2012) between 8:00AM and 12:00PM. Around 12:30PM, no one had arrived, so I called again. I was told by the agent that the technician was en route and would arrive at my home in forty five minutes. At 2PM, still nobody arrived. I rang again when I was then informed that my name had been strangely kicked out of the system and made available for a reschedule. Wanting to stick with a Maytag-approved business, I went ahead and scheduled the next earliest appointment available, Monday, July 9, 2012. The technician from A&E Factory Service that actually did show up reported that the entire control panel had to be replaced at a cost of $281.48. Interestingly, he added that he had seen other Maytag dishwashers with this exact same problem and recommended that I wait until the water settled before adding extra dishes during a cycle since water apparently leaks into the electronics via a small gap on the top of the inside of the door. Of course, there is nothing in the instructions warning against such.I chose to fix the machine since I didnt have the money to purchase a new one. Are your dishwashers designed to last only a few years? I truly believe that I have been duped by Maytag since this problem resulted from a design flaw. I am asking you to please look into these matters and correct any wrongdoing that you see fit. Copies of receipts for the dishwasher purchase and service repair are enclosed.

We purchased our double free standing gas range about 6 years ago. Our top oven went out about 4 years after purchase. We purchased the extended warranty from Sears and it was fixed at no charge. About a year later, the top oven would not work again. We called Sears, our warranty was up so it would be a repair that we would have to pay for. We decided to go with the Maytag repair service since it is a Maytag appliance and we had to pay anyway. The repairman came in and said that the top box that holds the electronic in it had fried wires and it would have to be replaced. So for $480, he could replace it. It was more than likely caused by a power surge. I just read that this also coincidentally happened to someone else so I find this cause to ask more questions. I also note that the top of the oven behind the burners where there is some sort of vent gets extremely hot (I accidentally touched it and had a blister the next day) when the oven is being operated. This is directly under the box that holds the electronic components. I would think that may have something to do with the wires frying since it is that hot directly below the panel. Could this be a defect in the building of the stove? Has anyone else had this instance beside the one person that I read about on your website?

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

We purchased this oven (MGR5775QDS ) along with a Refrigerator/Freezer, Dishwasher and Microwave on 2007 when we remodeled our kitchen. Since then the Refrigerator had to be serviced twice, the Dishwasher had a recall for fire safety - repaired, but I still have a scorched bottom tray, and the oven after self cleaning once has warped and the racks will not hold anything with any weight without collapsing. Maytag sent me new racks about a year ago, but that didnt help. I grill most of my meals or cook on the stovetop but on the rare occasion we try and use the oven it’s a nightmare. We lost a Thanksgiving Turkey and Easter Ham and recently a lasagna and a glass pan. Every time we have one of these events I search the internet in hopes that there has been some kind of recall on this model. It’s not safe. When the 20 lb turkey came crashing down, my wife was nearly burned by the juices that splattered and the house filled up with smoke. Happy Thanksgiving from Maytag - everyone go stand outside in the cold for 1/2 an hour while we clear out the smoke in the house. Recently when the rack collapsed and hot lasagna came crashing down, the glass/pyrex tray broke and left a huge bubbly mess in the bottom of the oven. Yay Maytag, thanks again - ruined a dinner, broke a dish and since we can’t use the self clean option, spent the rest of the evening scrubbing out the oven... and eating takeout food on Valentine’s Day. Sounds like the perfect Romantic evening right? I am so sickened with this company. We purchased all Maytag appliances because of their reputation. But now they dont even stand behind their products. What a shame.

Maytag Smoothtop Double Oven - Bought this stove 2 and 1/2 months ago and already buttons arent working. Very disappointed, not getting a Maytag again.

The washer 4 years ago we had the control panel replaced at our expense. Now, control panel is going out again. Also this summer I took the dryer apart to snug up some screws that had come lose, that were scraping the inside as the dry ran. I own a range and a dishwasher Maytag brand but will not buy another Maytag unit, even if they are built by my union brothers and sisters.

I purchased a whole stainless steel kitchen from Lowes and purchased all Maytag products because of the so called quality of Maytag. First we had to return the microwave because it was dented badly. We then notified Lowes that the door on the refrigerator cold cut drawer falls off when opening the drawer. Service man said he would send a new door. Same problem. You can clearly see that the drawer and the refrigerator frame is deformed. Maytag says that the warranty does not cover cosmetics. The range has a aqua lift self-cleaning technology that simply sucks. The oven does not clean! I recommend that no one ever buy Maytag products. They are the worst! I should not have listened to the salesman and bought what I originally wanted - SAMSUNG!!!

Wow, my dream oven, or now nightmare! I purchased a Maytag dbl oven MGR6775BDS in 2007. The top oven stopped working first after about 3 years and this week, the bottom. I cooked a meal on Monday and Wednesday. Without notice, it would not go past pre-heat. I have called several people and they all act as if this was a truly unique situation. Since I have been out of work, both my regular and extended warranty have expired. I had good faith in a product that carried the name Maytag and the fact that it was on sale for $1,200. I didnt know I had so much company. Yeah, I was told I could purchase a repair warranty for the sale price of $340. Oh yeah, I replaced a 20+ year old oven for the new and stainless dbl oven of my dreams.

This oven isnt even worth talking about. Just dont buy it. I used to bake a lot, but my recipes dont turn out anymore. My old oven was much easier. I dont know what the problem is, but I suspect it is oven temperature. The door also sticks. I have only had this a year and am ready to junk it.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

Maytag Glass top model #MER8600DHO. I bought it because it got good consumer reviews. This is supposed to be a self clean oven but the steam system in this model is not very effective. It doesnt clean the oven. Would never buy a range again with this oven cleaning system. I wanted to try a glass top stove but wish I hadnt. It is harder to clean and the glass scratches. I really dont like the self clean oven system in this stove - it flat out doesnt work and it takes a lot of elbow grease to clean the oven. The oven however seems true to temperature and does a good job. Overall I am Ok with this stove but wouldnt purchase a glass top again.

This oven has been used so very seldom that I didnt feel I could rate it until now. We use the oven 1-2 times a week since purchasing it in March of 2018. There hadnt been any reason to use the Self Cleaning part of the oven until last week. I have had a oven with self-cleaning for 20 years and the oven went out so we purchased this one because of its sleek look and features. However last week I decided to use the self-cleaning setting on it and came home after being gone all day to find that the house smelled like it had a fire burning in it. I ran to the oven to find the whole inside cover in a white powdery substance. It looked like a snow blizzard had gone on inside of it. I was use to a small amount of white residue being inside the oven after it finished and it just wiped right up. We spent hours vacuuming it out then scrubbing it down with vinegar water and a sponge with a scouring pad on it. The casserole spill was still on the bottom, most of the enamel is gone and the glass will not clean off. I did not use any chemicals in the oven prior to turning it to the self-clean mode, I believe that it overheated and burnt the enamel off and distorted the glass. Whirlpool offered to send me a cleaning kit. I told them that would do no good. I had already scrubbed and used a razor blade to try and clean the bottom and the glass and them sending me different cleaning supplies would not fix the fact that 80% of the inside protective coating on the oven is gone. Now it is a porous surface. A Serviceman was scheduled and he called prior to arrival today and asked me to explain what was going on with my oven. I explained and he said I can almost guarantee that Whirlpool will say that it is cosmetic and they only cover cosmetic for 3 months and that I will have to pay for a $100.00 service call. This is a load of crap. This coating is part of the oven to keep it clean and protect the metal from the high heat of baking in it. This is not cosmetic feature like the outside stainless steel finish or the black trim decor. The inside doesnt look pretty. It is a function. See the photos below. Whirlpool Range Item # 805150. Model # WEE510S0FS.

I too am a victim of the faulty Control Panel that Maytag put on these dishwashers - Model # MDB7749SBM2. $149 for the part and another $149 for service call and labor - almost half the price of what I paid 2 years ago! Should have stuck with the 10 year old builder grade GE I had with the latch door and turn knob! I am in the market for a new stove and microwave - I will never buy another Maytag or Whirlpool product! When is Maytag going to make good to all the customers out there that have experienced the same issue? If yours breaks it is a very easy fix now that I know. You can order the part and it simply unplugs and plugs in the new one. All you have to do is take the door off and it is right there!

Bought a new maytag gas range march 2013 model #mgr8674ab. The oven would not light at all. Would just click. Still under warranty. Called the service. They came and had to replace the controls in back. 2 months later the same thing, only this time it comes on and goes right back off. Then a week ago got it to light, used the oven and tried to turn it off and it would go off but immediately light up again. Scary to say the least. Another call to service. They are coming tomorrow. This is November 12 2013. I would not buy another maytag gas stove. There is something terribly wrong with this model.

I purchased the gas stove in June of 2012 from Home Depot, along with a Maytag microwave (Model MGR7662WB4). Home Depot installed both items. After trying to reach into the microwave about the stove, the knob would turn itself on with me brushing up against it. This happened several times, and one time the flame shot up and I almost got burned. The last time it happened, I did not realize that the knob was turned very slightly and gas was coming out of the burner for several hours. If it were not for a friend stopping over, I would not have considered the odor being from the stove. I assumed that the drains were probably backed up and started to add cleaners to the toilet bowls. I had to open the windows for several hours to get the smell out. So I called customer service 2 times. The first person said I would have to pay for the call if the problem was not Maytag and I said, “Forget it.” Then I went into Home Depot and the salesperson in there gave me another number to call for service. They came last Friday and said that he had seen at least 10-15 calls about this and since the unit was working as designed and no recalls, there was nothing they could do. “Just wait and see if a recall would be put into place and I would be on the list to fix it. In the meantime just keep the knobs off (which I was doing already out of fear).” My sister just bought a Whirlpool gas range this summer as well and asked if I could try her knob and it worked perfectly. Again I called CS and was told they could not send me those at no charge and that it would cancel out the warranty. So I asked her what I have to do before I or someone else gets injured and she said that until there was a recall, there was nothing they could do. I told her I was going to contact Consumer Report as well as Pam Zekman on Channel 2 news in Chicago. End of story; I still have the problem and no knobs on the new stove. Anything you can do to help please contact me, and thank you in advance.

Maytag AquaLift Oven #YMER8880BW - The aqualift technology does not clean the oven. It is sorely inadequate. I bought Maytag because of its reputation. This range should be recalled as should all their ranges with this useless technology. Buyers BEWARE! Do not purchase any range from Maytag which advertises Aqua Lift technology. This purchase has soured your reputation Maytag. I also purchased a fridge with the stove. I will NEVER buy a Maytag product again. I also would like to ask frustrated and disenchanted readers how they are getting their ovens cleaned. What product(s) can be used. Maytag - complete FAIL!!

2 years ago I purchased a Maytag Washer & Gas Dryer. Unfortunately, I did not invest or believe in extended warranties. I believe in trying to buy quality products. The door on the washer would not open and 2 error codes were displayed. I was trying to add another piece of laundry and the washer had just started. I canceled the load, waited for the door lock light to go out, but the door would not open. The error codes began displaying E3 and F5. I immediately went to the Maytag website for a resolution. The suggestions did not work and was instructed to obtain service if they did not. I called for a service call for $35, but was told that the repair would be over $300 for parts and that was not including labor. The parts I needed were a control panel and a part for the door lock. This was not a Maytag Company service tech and he told me that this happens because the parts are plastic. Currently, besides a Maytag Washer & Dryer I have a microwave, stove, and dishwasher that are also Maytag. When I replace these appliances, I WILL NEVER BUY ANOTHER MAYTAG PRODUCT. I expect the quality and life of an appliance to be more than 2 years, without buying an extended warranty. When I told a friend what had happened with my Maytag Washer, she told me that she had a Maytag Washer broke down with a control panel problem, and she couldnt remember the other part. She informed me that her repair was over $500.

We purchased the Maytag over the range microwave December 2014. Three months after installing it the door cracked. Maytag did replace the door and the repairman thought it might be due to the heat from the stove (huh, it was designed to go over the stove, where there will be heat). Now, six months after that, the layers of plastic on the door are separating and the piece around the control panel is cracked. Maytag agreed to replace the control panel but refuse to replace the door as it is only cosmetic (their words). So much for paying a little extra for what we thought would be a quality product. It seems to me that if something was made to go over the stove, it should be made to withstand the heat.

We bought a new home with all new Maytag appliances. Our Maytag dishwasher has had 3 new handles, 1 inside tub and now needs a new touch panel. Our Maytag oven/stove has needed three ignitors and the oven door has never been right! The microwave is the only appliance that we have not had a service call. Appliances are expensive along with parts and labor for service calls. I will not be purchasing any more Maytag appliances. The standard comment by repairman: They dont make them like they used to. How sad is that!!

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

Purchased a Maytag Centennial Washer from Lowes. This is the NOISIEST WASHER I HAVE EVER HAD. Self Balancing, pretty much the way it is, YOU lift that heavy wet laundry and re-arrange to balance. It just slams around even moving the washer, until you do. This washer also doubles as a BLENDER. It SHREDS laundry. The agitator does not go all the way down and thus, clothing, towels, rugs... get stuck under the agitator, wind around and RIP. Have had hundreds of dollars worth of laundry shredded such as: shirts, towels, new rugs and it even ripped the waist off a pair of my jeans! The other laundry gets tied up on the stuck laundry and you end up with a twisted, ripped, tied up Laundry Ball. It will not wash or rinse well when it does this, naturally. Lowes: The salesman knew about all this, and sold it anyway! He had one and got rid of it. Gee thanks Lowes and Maytag, for the worst washer I have ever had the misfortune of owning.

When I remolded my kitchen almost four years ago, I purchased four Maytag appliances. There was a recall on my dishwasher that was successfully fixed; the heating coil could have caused a fire. The next appliance to go was my refrigerator with a bottom freezer: the freezer section went. Thank goodness I purchased a policy which covered the repair that had to be done twice--twice I lost food. I was compensated by the insurance company for $200.00 for the cost of food lost. Just before Christmas my microwave stopped heating. The turntable works, the timer works, but it will not heat the food and makes a loud noise. The glass top on my stove is getting marred even though I clean it every time something spills. I keep my appliances in immaculate condition and they look like new. I thought when I purchased Maytag I was buying reliable appliances. Their ad that states that the Maytag repairman is lonesome because he has no work is a lot of bull. Each appliance has had problems. Where is consumer protection? Appliances should not breakdown after a couple of years. We should not have to buy insurance policies that are expensive to protect appliances that should last at least ten years without problems. Someone needs to step in and help the consumer. I didnt call Maytag regarding the microwave as I was told it was useless to call them and all I would get would be aggravation. Someone, please help the consumer!

Great stove for the price. The oven bakes good, the self-cleaning oven is awesome, the top is easy to clean up and regulating the temperature is so easy.

Wow! I wished I had reviewed this page before purchasing a Maytag. We bought a new Maytag Range (#MGR5751BDD) from Menards in March 2008. Within a couple of months, we were out of a stove. I was lighting the burner to make dinner for my family (it is a gas range) and all the burners started making a clicking noise and they caught on fire. Luckily, my husband was nearby and took the fire extinguisher to it.We thought for sure that the house was going to be gone. We contacted Maytag and they had a guy come out (wasnt the friendliest and cted like he could care less). He stated there was wiring that was bad but because we took the fire extinguisher to it we probably voided the warranty. What? He would submit a report to Maytag.Maytag reluctantly gave us some money but not near enough to cover the stove that was only a couple of months old. Now, I cant use the new range that is 2.5 years old. It pops and spurts because the regulator needs to be replaced. The bad thing is by the time we pay for a repairman and the new part, it will cost us a lot of money we cant afford. This stinks.

Almost one year to the date of purchase, my Maytag glass top range stopped working. The oven is still operational, but the range top does not work. The knobs turn and the surface lights go on but the elements no longer heat up. Trying to get a response from a real person at Maytag was impossible. I was put through a myriad of prompts that led me to scheduling a service appointment. I called AppliancesMart and got a wonderful sales person who said a service call would cost me 60 to 80 dollars and that he had not heard of repairs below $300 for this type of problem. Needless to say I am very angry and disappointed that I had not done more research before I purchased this item. If I can prevent one more person from making this same mistake, I will get some modicum of satisfaction out of this horrible experience.

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

I have written to Whirlpool about complaints with this range and was very dissatisfied with response. The following were complaints on above range: Range does not have a light on it as the past ranges had. It is very much needed. Grates on burner are to high, therefore it takes longer for items in pot to heat up. Type of steel used on range is very thin and tiny, in other words very poor quality. This is what has happened since Whirlpool bought out Maytag. Quality of Steel that Maytag used is no longer since Whirlpool took over their products. This is true of All their Appliances (Refrigerators, Washers, Dryers, and Ranges). All meaning appliances manufactured by Whirlpool.Manual knobs for turning on oven have been replaced by touch screens, these eventually wear out and are very costly to replace. If it works why change it. Drawers on bottom of range used to be larger, now they are narrow and smaller height wise. Residue on base of burner appears quite frequently and has to be cleaned even if no overspills occur. And why cant Whirlpool make quality merchandise as good as Maytag use to make. Regarding the physical appearance of Range it is very attractive in looks, however Looking good and functioning poorly with inadequate materials used in construction of Appliances outweighs benefits of looking good. My wife and I regret not returning this appliance within 90 days of purchase. In the future we will not purchase Whirlpool or any other appliances manufactured by them if that is possible. Kenmore, LG and perhaps other appliances parts are made by Whirlpool. I received a response from Jake **, Whirlpool Corporation, Executive Office. The Comment from Jake that did not impress me was this: While we regret you are dissatisfied with the current design of your Maytag Range, this is the model that you selected. His comment says too bad better luck next time. Letter was dated March 5, 2014 received on March 13th or 14th.I sent a handwritten letter to Mr. Jeff Fettig on March 12th which was written on March 11, 2014. No response to handwritten letter to Mr. Jeff M. Fettig. Verification that the Executive Office that my email to you Mr. Jeff Fettig Chairman and Chief Executive Officer Whirlpool Corporation was received on February 20, 2014 by Delores **, Corporate Office Staff. Supposedly Mr. Jeff Fettig.

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.

I bought a Maytag electric stove steam lift oven 2 years ago, I regret it. I baked a pie, and used the steam cleaning, it didn’t clean, my oven is still dirty. The top of the stove is not easy to clean and scratches very easily. It’s not my first stove, different brand, and I never had problem like I have now. I should have stayed with the brand I had before. My other regret, I should have read the reviews.

We updated our kitchen appliances in 2013 and purchased all from Home Depot. Purchased Maytag Refrigerator, free standing range and microwave. What a big mistake!!! Not one of them are worth what we paid for them. I just noticed that I was getting a (chemical) smell from inside our 6 year old 3 door model MFI2670XEM5 refrigerator. Well being I know what refrigerant smells like I have a leak in the interior of unit. This is my final issue with Maytag and their so called great built appliances, I have had nothing but troubles since about 2 years after we purchased it.I guess what really surprises me is that unit is built by Whirlpool and has their name all over unit and I always had good luck in the past with the brand. This is one of several issues including rust on freezer door, broken plastic drawer frames to French door hinges broken, ice maker door issues. What a waste of my money that I spent on these and now after 6 years need to buy all new. IT WILL NOT BE Maytag or Whirlpool!!!

Purchased my microwave in 2005 and seldom used it. However in the last few months, the halogen light which lights up the range surface has been flickering. When I asked an electrician doing other work around my house to repair it, he discovered that the halogen light is attached with a dual pin socket which is plastic. When the halogen light gets overheated (and halogen produces alight of heat) it melts the plastic. It has already melted some of the plastic socket. When it fails to operate, I will have to repair the light socket which will be very expensive or buy a new microwave. This microwave cost $800 or more because it offered convection cooking which I have seldom used.This is what is presumed quality appliance? Plus I added the cost of an extended warranty.

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

I was in my bed and lights and TV flickered. Then, I heard a small explosion and my dogs went crazy. I went into the kitchen and my Maytag Gemini stove was smoking and smells really bad. I unplugged it. The sockets and the one close to it no longer work. My house stinks now. What happened? I have had this stove for a few years but it is not used often except during the holidays.

Havent even used the range yet and the paint is peeling off of the top. I have had the repair guy out. The new top piece of the range arrived with peeling paint also. I put in a claim to have the range replaced and was told they would contact me in 24 to 48 hours. That never happened and so I called again. They said that they would call and, of course, it didnt happen. I paid $1,300 for a stove that looks horrible with the paint is peeling off of it. What kind of ** is Sears selling? Maytag is owned by Whirlpool and nobody wants to make this right.

Ive been a Maytag consumer since 1980. I bought washer, dryer, refrigerator and a smooth top oven. I replaced the washer and dryer with the Bravos series on November 22, 2011. Everything was fine until 6 weeks ago. The bearing went bad under the drum. 2 techs and 2 weeks later, at the cost of $527 and change spent on repair for a $650.00 machine, I started to look into reviews. Not! Can you say class action lawsuit! The fine gentlemen informed me 5 years ago about the Canada buyout, a local retailer that only sold Maytags. He shut his doors due to the fact that he will not work on junk! Oh well, he was right. 13 months worth of use and Im going to spend that kind of money. Now I understand why the repairman in the commercials retired! Shame on you. Love, crazy Mike.

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

We had a Whirlpool stove/oven for many years, and it was finally time to trade it in. Everything about that unit was good. While shopping for another Whirlpool, the sales rep told us that Maytag and Whirlpool are one and the same. That we found, is false. An important feature for us in an appliance is the self cleaning oven. The Maytag oven had to be leveled four times after it was installed, in order for the self clean feature to function. The self clean part is only a small indented portion of the bottom of the oven, not the entire oven. And even that does not clean. After going through the dealership service about this problem, I contacted Maytag. My final frustrated summary to the rep was that I understand that we bought a lemon, and you are not going to help us in any way. I just want to say to anyone considering a Maytag stove and oven, raise your standard. If you choose Maytag, you will only be disappointed. I am.

We built a new home in 2008 and purchased a Maytag appliance package from Home Depot, including a dishwasher, stove and refrigerator. From the beginning, we had problems with our French door refrigerator (MFC2061HEW; it has been discontinued). Within the first year we had 3 ice makers replaced because it was not making any ice. Now, mind you, we went through Maytag to have their repairman to service our appliance and they set up all the service calls. We limped by for awhile and called a different repairman to come and check the fridge because it was not staying cold or making ice again and, of course, it was out of warranty. The first thing he did was check the freon and we were told that it didnt have enough freon to keep it going, so he recharged it and it worked great. We have had to have the repairman come back again this month because it stopped making ice and the temperature for upper and lower was all over the place. He checked the freon again and said the unit has a slow leak in it and he was unable to fix that. I contacted Maytag because I felt if the first repairman had checked the freon from the beginning, we wouldnt be having this problem. The only suggestion I got from them was call a company with a dye kit test and that they are sorry, but its not under warranty. I dont know about anyone else, but $2000.00 for a fridge that has been a pain since day one is a lot of money to replace. I feel they dont care about their customers and they should be responsible for paying for the repair that should have been caught from the get-go.

Our Bravos model mvwx0600xw0 is 5 years old. I have been dealing with the clothes getting tangled, dark colors full of lint and streaked since I had the machine. Recently the lid lock light has been blinking with 11 minutes left in the cycle. I thought maybe it was off balance, so I stopped the cycle and rearranged everything. Same thing happened again with the lid on the drain and spin cycle. After reading all the other reviews, I realize it is not worth fixing. So long Maytag. It was good knowing you when you sold quality!

My Maytag model MMV4205BAB microwave turns on and heats when the door is closed. We paid a lot of $$ for this overhead microwave and it has not been a satisfactory product. The turntable broke within a couple of months and now this. Im afraid it will burn my house down. This is a defective product and in my opinion it should be recalled. I have read several other posts about this exact model and problem. We purchased all Maytag appliances for our new home and we have had problems with all of them. The auger on the ice maker on the freezer broke within a couple of months. The handle on the oven door broke off while the builder was installing the appliances, and the top of the line dishwasher doesnt clean the dishes. It leave deposits on everything, no matter the detergent used. Ill never purchase Maytag again!

All in all I have liked my electric range, but I have 2 issues that I am having trouble resolving. I bought the range in 2003 and to find the model number I have to pull the range out from the cupboards on each side which would be extremely difficult under the circumstances. The reason I want to get the model number is so that I might find replacement parts for the doors edging that has flaked and rusted and is quite unattractive.

I purchased a Maytag gas stove. Right away I noticed the oven racks would sag in the middle pulling the back corners to pull away from sides dropping the rack down on top of rack below. I got a hold of Maytag and they sent me out a set of 3 new oven racks that were exactly the same as the ones I had. I have been fighting with them for years. I called Whirlpool today who make Maytag and was told its off warranty and that I can order another set of oven racks at a cost to me. They would be the same as I have. The racks are so cheaply made and cannot stand even a few pounds. The finish on the stove also chips very easily. You rub a pan up against it and it scratches the white porcelain off. I spent a lot of money buying the dream gas stove I had thought, but only to be unsatisfied with my purchase. Buyer beware of Maytag products.

My complaint is not against Home Depot but Maytag Products. They are inferior products. Stay away from Maytag! Note: We are in our mid-to late 60s, no kids using these products and they do not get a lot of wear and tear. Maytag Microwave: MMV 4205DS-0, May 29, 2014 we purchased Maytag appliances for our kitchen (stove and microwave from Home Depot). I liked the 10 year metal warranty plate attached to the front limited warranty of the microwave. This means nothing! They cover the stainless cavity of the microwave (a part that will never go bad). June 3, 2014 this microwave was delivered. Thanksgiving, the microwave went out November 30, 2015 this was replaced with GE Profile Model JVM3160RFSS for $178. November 30, 2015, Diamond Factory Service was here for the Microwave. We paid $90 for the service call. They wanted $228.09 to repair (1-8206419 Switch $15.22; 1 W10269460 Switch $27.03; 1 W10727360 Microswitch $27.03 and Labor $155.00). Maytag Dishwasher MDB7749AWM. Purchased from Al race Appliance for $599.95 total with tag etc was $920.27 on 5/16/12. So thankful was purchased the additional warranty for five years. We have had 2 service calls so far for the same issue, which is W10356494 Console CMFF0312434. This is a known problem (it will not start). I wish I would have googled the model before purchase was made. When the warranty expires, this will go to the curb too.Also, purchased Maytag Neptune Washer and Dryer from Best Maytag, Rockford. The dryer had problems with the circuit board after a short time. Too expensive to replace. Our family and friends ALWAYS purchased Maytag only. No more! Stay away! We are waiting for the oven to go next. Oh and check out the bottom drawer. There use to be room for pots and pans. No more. Lucky to get your pot holders in there.

I have the model with a smaller oven on top. I use it about 98% of the time so Im not wasting energy having to heat a larger oven space. I also like the fact that I can clean one oven. The larger oven is used when I cook turkeys. I can cook many dishes at a time, by using the smaller oven for dressing or cakes.

Purchased a Maytag Electric range Model MER8800FZ2 in 2019. The surface Scratched the first week of purchase and the stains will not come off. When I called customer service they claim they are not responsible for cosmetics. In my opinion, This model was put together with the cheapest material they could find. Maytag is not what it used to be. The Elements take a long time to heat up. Inside the oven, the Glazed Paint is cheap product also where once it stains with food it never comes off.

Paint bubbling & peeling off appliance: I purchased new double convection oven from Lows (Maytag). One month after delivery, paint began to bubble and peel off. Maytag takes the position that as long as the oven functions properly, the paint is simply cosmetic and the warranty does not cover cosmetic problems. Maytags position is that even if all the paint peels off but the appliance still functions properly, too bad for you!

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

The oven works. However, there are two safety issues. First, the flat metal panel above the air vent and below the instrument panel gets extremely HOT. This is the location we can easily touch, especially when we operate the instrument panel. We almost burned our hands. Second, the edges of the unit are very SHARP. We almost cut our legs. These are serious safety issues. In addition, we/I tried to post a review at Maytag site pointing out these safety issues. The review was twice moderate (i.e., rejected). Even though I used to like Maytag, this experience changed my mind.

I thought I was safe in buying Maytag for all of my appliances in my new kitchen. I bought a double wall oven Maytag MEW6630DDS. I bought it in late 2010 and have had no issues until August of 2018. I rarely use the bottom but used it in August of this year to cook cupcakes. After baking them and leaving the kitchen for a short while I heard a loud explosive, shattering sound. I walked to the kitchen to see that the bottom oven door had shattered into a million pieces. Thank the good Lord that I was not near it. I contacted Maytag to see if there was a reason it would have done this. They said that there had not been a recall. They sent a repairman at no cost to look at it. He came, took it apart and had no reason for why it would have done this. He left it in pieces and said that he was ordering the replacement door. Maytag advised us to turn off the breaker to the oven. After a month without ovens, the repairman called and said that the part had been discontinued. HA! You think?!? It has the potential to explode. It should have been recalled, not just discontinued. Maytag offered us 20% off a new set of $3000 wall ovens or $150 to pick ours up for disposal. Talk about saving the company money and screwing over the unlucky recipient of a defective product. They ought to be ashamed. I am going to have to replace the broken glass with aftermarket glass. What is going to happen when I use the self cleaning option? What happens when the top door explodes. I am scared to use my very expensive wall ovens that I thought would last at least 10 years. Shaneka at Whirlpool said that people have appliances fail all the time and just have to buy replacements. Do all of them have to replace ovens because doors explode for no reason? I am not the only one this has happened to. I have found several other complaints of this on the internet. Why did they discontinue these door? I wonder.

A month ago I purchased a 25 cu ft side by side. First the recirculating fan quit. It was repaired. But the water and ice hose in the door froze and cracked the entire freezer door. Must be replaced, unfortunately they dont have any, so I was quoted 6 weeks for a new door, that has turned into 12 weeks and they cant guarantee me a date. I requested a replacement fridge and was told, They cant do that. I purchased the full Maytag package - stove, dishwasher, microwave. I expect better customer service than that, Take a door off the assembly line and ship it to me.

I read some of the reviews on the Maytag ovens. I too have the same problems! Have had control panel replaced and still have to set at 400 if I need to bake at 350. It also takes forever to preheat. Trust this review because I am one very unhappy consumer!! DO NOT buy Maytag!!

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

I can see by the comments on this page that the letter I sent to Whirlpool was in vain. I purchased a Maytag double oven gas range (MGT8775XW00) from our local Lowes. We were remodeling a home we had purchased. Unfortunately (as anyone whos been involved in home remodeling/renovation knows well), it took much longer than I thought it would before range could be installed. It was several months later before it was installed. First time I tried to use the top oven, it would heat to set temp (I assume) and then shut down. The larger bottom oven had erratic heating. I tried adjusting oven temps but it was a guessing game. We had Fix-Rite Corp out twice and they were puzzled by the problem. Two times, they replaced the control panel. After the second repair, it was decided the only thing to fix the kitchen was a complete gutting, new cabinets and floor. The oven was pulled out before I had a chance to use it again. By the time we got the kitchen finished and range reinstalled, I discovered the oven still had the same problems and the broiler would ignite sometimes and when it did, the flame would go out after 30 to 60 seconds and would not come back on. By this time, we were past the one-year warranty. After the first repair did not work, I tried to get Lowes to take it back and assured them I would purchase another range from them. They said they could not do that. Now I can see Im going to end up buying another range. Be assured it wont be Maytag and it wont be Lowes. I also own and use Maytag washer and dryer.

Purchased 4 Maytag kitchen appliances - stove, double oven, fridge, dishwasher - was told that they were all made in the USA. WRONG. The microwave comes from China - not sure why Maytag is not being honest. Not happy with my purchases - even though we spent $4000 to buy American. Warranty service is awful - even extended warranty is a joke. Would never purchase Maytag again.

If I could give less than one star I would. I purchased a Maytag range in September 2021, 33 days later the oven went out!! I have been fighting trying to get it repaired for months!!! The parts are not in, the parts have been shipped, oops we forgot to ship the parts, the technician is on vacation. You name it, I have heard it. After the phone call today, it looks like I will still be without a range at Christmas!! This is totally unacceptable. I purchased a Maytag because I assumed it was a good brand! Do yourself a favor... Never buy a Maytag or Whirlpool Appliance. Its not worth it. For the range to only work for 32 days is just plain Wrong....

I bought a Maytag MGR5605WW range on July 3, 2011 and it took till mid August before I received it. Right away I noticed when I put a pan on the grates, I had to be careful so they did not slip off. Dangerous! Then I made a pizza, and when I pulled the rack out of the oven, the rack tipped down and the pizza slid down on the oven. Danger again! I went over to Menards and they gave me the number of A&E (1-800-771-3029). I called them when I got home and an A&E person said they would call me back. After a few more calls, no one ever called me back. I went back to Menards. They said I need to deal with Maytag. I am very concerned with the racks, and so is everyone else. They are cheaply made. Tonight I had a family member place the frozen turkey on the rack and it bowed down! Danger again. The grates have a few chips. This is a nightmare. What a piece of trash. I’m trying to get someone to respond. This stove is dangerous to my well-being, and I have no other choice but to use it.

The first problem happened a month after we bought the horrible product. I had biscuits baking in the oven and the oven door locked itself like when in self-clean mode. Maytag sent out a repairman that had the part in his truck because they knew there was a problem with that models door. I pointed out that the door does not shut properly, causing inaccurate heating and scorching on the outside of the oven door. The repairman insisted that it was shut properly, and that it was designed at the angle the door sits. He replaced the scorched part of the door, but it immediately scorched again. I have had the part replaced 3 times, and will not do so again until we sell the house. I have spent over money over and over again to make the repair, because it makes the stove look like it is filthy with grease. Now, all the dots painted on the glass top are coming off, and the remaining black glass behind it also looks like burnt grease. It is so embarrassing when entertaining; but the stove is clean. I spent a lot of money for this, and it has been junk from day one. Avoid purchasing.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

I bought a complete kitchen: stove, fridge, dishwasher microwave. Suppose to be stainless steel. All have rusted out within 6 months. Maytag does not stand behind their products. They sent me cleaners and all my appliances rusted more using their cleaners.

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

If there was a zero star rating available, that is what I would select! We purchased this range along with a complete kitchen ensemble for a remodel of our kitchen in December of 2011. Within a few months of purchase the enamel finish started blistering, flaking and peeling. Upon contacting Whirlpool Corp about the problem through their online chatline, email, regular mail and phone, we were informed (quite rudely I might add) that Whirlpool does not warranty cosmetic deficiencies over 30 days after product purchase. This is American Quality?? Since this has occurred the retirement home we are building will have no Whirlpool Corp products in it which includes: Maytag, Whirlpool, KitchenAid, Amana, Jenn-Air, Brastemp, Consul, Bauknecht, Gladiator, or any of the product lineup from the Chinese company Hefei Sanyo which they are buying. The attached photos were taken in May of 2012 and since that time the product finish has only exponentially deteriorated.

Purchased a Maytag Dryer, Washer and Oven Range in December 2011. Both washer and oven were serviced within 1 year under warranty. The dryer stopped working in August 2013, not under warranty. Total cost to repair is $450. Called Maytag to see if they could reduce the repair cost, answer... NO. Maytag spends millions of dollars in advertising... Built Strong to Last Long but they cant spend several hundreds to keep customers. Will never buy a Maytag, Whirlpool, KitchenAid or any other related company product ever. Their motto should be Built Weak to Last Weeks.

I purchased a complete Maytag set for my kitchen (fridge, double oven, microwave, dishwasher) from Home Depot on November 22nd 2012. About two months ago I noticed the dishwasher started to glitch here and there, but was still functional. I removed the panel and found that the wiring was completely corroded and would need to be replaced. I put everything back together and have managed to make it almost a month on the same cable. In the mean time, I searched for my receipts, my manuals, and anything else to show my purchase given the 10 YEAR WARRANTY Maytag wants to mention as a sale point. Aside from Home Depot not being able to find my order information to duplicate the receipt, I managed to find where I had ordered my set online and was emailed a copy. Home depot is not involved with the warranty process, unless you purchase the additional warranty. They deferred me to Maytag. I contacted Maytag and was informed that the warranty only covers the stainless internal tub, the racks, and the chopper. Seriously?? So, absolutely NOTHING mechanical about the product past one year.After paying the $699 for the washer, and another 57.99 for installation and kit, I was told by Maytag that I could buy another 1 year warranty that would cover the part, but it would cost me $289, or roughly half the price I paid to get a whole two years out of the dishwasher in the first place. This means I might as well be paying almost $300 a year just to have this product... ridiculous!! Just to buy the part and do the work myself, the part is $172 plus tax/shipping. Since it is only 4 screws and a couple clips holding this thing on, I am likely going to go that route.I have read many people saying similar things about the electronic wire corroding and this appears to be a well known issue with their products. They recommend sealing the entire area using a tube of silicone to help reduce the amount of time it takes to ruin another cable. Very very very poor craftsmanship. Nice racket they have through charging people so much every couple of years for their products!! As my $4000 kitchen appliance set falls apart, I doubt I will ever replace it with another Maytag item.

I purchased a new MVBW725BWO washer. The cycle use and guide chart is generic. It does not remotely match my model. I called customer service. No help. She told me to tell her what I am washing and she will tell me which cycle. Really? Every time I wash a load I need to call her/him? I am not a laundry rookie but this machine has many buttons and choices. I want to do the right thing. Too bad. I washed two blankets and continually get an UL (uneven load) indicator. I have rearranged these two blankets every way possibly and there is no clearing the message. I called Maytag. No help. She told me that I should either 1) unplug the appliance, or 2) trip the breaker. Are you kidding me? If I didnt like those ideas or find them useful, call back and she will dispatch a service technician. Laughable. I guess I can pull them out of the washer, drip water everywhere, hand wring them, and move on. What happen to the good old days?

Model MMV4205FZ3 microwave hood combination. No problems with open door signal yet. However, light over the stove burnt out. When removing, it exploded.No didnt unplug first. Previous microwave didnt have a problem with this. Instructions are useless. Didnt say to unplug and doesnt provide a model number for the bulb. Consequently, we have now purchased 5 different bulbs and they dont work. Tested socket and power is going to it. Rep at Ace Hardware said he had heard about this happening several times and provided what was to be the correct bulb -- didnt work.

Once again I purchased a maytag appliance. I was hesitant because of poor past experience. I bought a refrigerator, lasted 3 years, and a stove, a little better 4 years. When I went to buy a dishwasher at home depot, they assured me that maytag had improved their standards and now were more conscious of maintaining the quality of their products. Long story short, I bought the dishwasher in april of 2015 and now in october of 2015 the control panel is shut. I have requested a repair, but find this unacceptable as the life of appliances seems short at best. I am fearful this could be on going as I now am reading the customer reviews, and 90% of them have had this trouble more than once.

In the process of self cleaning mode, oven died with door locked. Thermostat and thermal fuse went out, couldnt get oven door open or control the situation in any way except pray for no fire and wait for hours till oven cooled down. Door could not be opened, it died in lock mode. Called repairman, already in to 2 repair bills, still not operating. Called Whirlpool and Maytag, no help!! But amazingly they have created a new kit for the blower unit in this oven, model # Mew7527AW00. I paid a bunch of money for this oven, which replaced a 40 yr. old oven that had been in its place, operating fine, but it was Aqua Blue!! Its so sad that a huge Company as this will not help with an almost new Oven??

Purchased Maytag Double Range MGT8720DH00 in March 2015. Within 2 months had to call gas company due to leak and service came out to fix it. Now anytime my house is closed up during a vacation or extended period away I come home to a locked range with a warning message to check to make sure that the knobs are off. Had gas company (who also called fire department) to come out tonight after returning from vacation with same issue again. They tested and said CO2 was ok, but to check reviews for similar ranges and I have seen repeated issues in reviews for Maytag products. The firemen all commented when they saw that it was a Maytag so it seemed like they have seen these issues before. Very scary to think we could be exposed to a constant low level gas leak in our home. Keeping windows open at all times is not a realistic option.