Purchased the Maytag Aqualift self-cleaning oven and this feature doesnt work at all. I would have never have made this purchase if I knew the oven would not self clean. This technology with the water in the bottom to self clean is pathetic! I thought maybe it wasnt working and called for a repair since it was under warranty. The service man told me not to expect it to clean like a regular self-cleaning oven. But I complained that it did nothing at all! So now I have a self-cleaning oven that I have to clean myself!

I have a self cleaning Maytag electric stove. I discovered the self cleaning starts after so many times of using the oven. But the stove didnt give me warning of this when I put my Thanksgiving turkey in the oven. Halfway through cooking, the oven door locked and went into cleaning mode which scorched my turkey and could have possibly caused a house fire. Also, my top burners have a mind of their own, while cooking they turn up on their own. This stove is very dangerous.

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

I purchased the Maytag double-oven gas range, Model MGT8775XS, in 2013. The quality of this double-oven stove cannot be understated. Performance? Terrible. Reliability? Awful. My experience was shocking because when I was a kid, Maytag was the ideal for quality and reliability. Those days are over. When delivered in 2013, the ovens did not work. Heating went to 200 degrees and stopped. During the next three years, we had this Maytag stove repaired four times. The most recent repair was in October 2016. A new regulator and igniter cost us $360. Four weeks later you guessed it the ovens stopped working yet again. We sent the Maytag stove to the recycle dump. Its far more valuable as scrap metal.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

I can honestly say that my Maytag refrigerator is indeed the worse appliance that I have ever purchased. This is how it rolled... I bought a new Maytag stove, frig, microwave, and dishwasher in June of 2006. Here is what I am now dealing with... the frig went on the fritz 2 years ago (warranty expired). The problem being the freezer would not automatically defrost. Because of this the coils would ice up and this prevented the cold air from moving from the freezer into the frig part. Things remained frozen in the freezer, but everything became warm on the other side, the frig side. I had it repaired about a year and a half ago to the tune of $165. Then about 6 months ago the problem reoccurred, but instead of paying for another repair I figured out that if I used my blow dryer I could defrost the ice from the coils on my own.Unfortunately, the problem reoccurs more frequently now and I have to manually defrost the coils almost every week. This past weekend things finally came to an end as no matter how many times I manually defrosted the coils, it would be fully iced up again with an hour or so. Also, all the time it is acting up it just sucks up electricity, and I have notice a spike upwards on my energy bill. It must be related to the frig. So, I bit the bullet and bought a used frig on craigslist just to hold me over until I have time to do research on what appliance brand is indeed reliable. I should of done this before I bought my Maytag appliances from Home Depot. As far as my other Maytag appliances, here is their current condition. Microwave about the stove: the handle broke off a little less than 2 years after purchase. Stove: now has rust on the front of stove, at the bottom of the stove which is a pull out drawer.Dishwasher: not working at all. The start button doesnt work. Normally, you just push the button and a green light comes on and it begins the first cycle. This is no longer happening and no green light comes on. Refrigerator: Took it to the dumps this morning to be recycled. Cant believe it, all of these appliances are nothing but crap and I will never purchase another Maytag. I have shared my experiences with all my family and friends and have encouraged them to avoid Maytag, as it is not even close to being the product it used to be. Another piece of junk coming from somewhere other than here in the USA. We lose jobs here in the US, and then end up buying the goods from another country that makes inferior products. How stupid can we get!

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

Maytag washer, dryer, oven, microwave over-the-range - all crapped out in four years. I will never buy or recommend Maytag. I believed them to be one of the best brands but apparently theyve learned a few too many shortcuts.

I purchased a Maytag Gemini April 22 2017 and I am very unhappy with it. The ovens are not working properly. I have thrown away so much food because the ovens won’t hold temperature. The display says it’s the temp. I set it but the temp keeps dropping and rising causing the bottom and top to burn and inside not to cook. Both ovens are doing it. Had a repairman come day before Christmas. He said there is nothing wrong. He said set temp, when preheat beep goes off wait 15 minutes for it to cycle then insert food. I tried this Christmas Day. Oven is still not working and again I threw away more food. I am so disappointed in Maytag. Serviceman is set up again to come out next week. I think I got a lemon. Please. I think they should replace the whole range. It’s not fair. I paid so much for this range and can’t use it.

We bought a new Maytag electric range from a local dealer three years ago. The oven element quit working, which shorted out the motherboard that controls the entire range. The cost of repair was $500 for the element, motherboard and installation. We have owned other brands that lasted 20 years and worked fine with no repairs. My folks have used Maytag for over 50 years with no problems. Who and where is this junk manufactured now? China? I will never buy another Maytag product!

We purchased a Maytag convection oven less than a year ago! Today is the 3rd time the heat sensor has gone on it! I want a new stove! I am beyond disappointed with the business and the product! Have always bought Maytag! Rethinking it now!!!

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

I purchased my Maytag gas range (model number mGR7665WB) on Thanksgiving 2011! It worked fine until May 2012. Then the bake function just stopped working. If I select bake, the temperature fails to rise above 100F and a sickening gas smell fills the kitchen! PC Richards, where I purchased the product from, sent a repairman who took two weeks and two visits to fix the part! Everything was working fine until six months later during cooking for a full house on the day of my daughters birthday party. Same problem, bake function failed again along with gas smell! I was pregnant at the time and very worried about the gas smell! We had to leave the house a few days after that due to the hurricane and when I returned, everything worked great for a few weeks only to fail on Christmas Eve leaving me to cook the meat for our Christmas Day dinner in a neighbors house, highly embarrassing and inconvenient! Now Maytag and PC Richards are only able to repair at a high cost to me which I cant afford and feel I shouldnt be responsible for as this product has been consistently unreliable and possibly dangerous. I am especially concerned about the gas smell as I have a newborn and a 3-year old in our small apartment!

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

I bought a full kitchen of Maytag appliances when I bought a new house in 2009. I thought it was a reliable company. Id always gone with GE before. I couldnt get the packing sticker off the oven after trying everything to remove it, so the oven bottom is virtually ruined. The timer on the oven dings once and stops; dinner burns if Im not right there to hear it. I was told by customer service thats the way it works, so I had to buy a separate timer. I am now replacing my 2 ½-year-old dishwasher because the control panel has once again stopped working. It cost me $275 to fix the first time and it lasted less than 3 months. I will never buy Maytag again! I got over 20 years of service from my GE appliances.

My refrigerator was delivered on April 3, 2016. I began calling for service July 2 when the bottom freezer door started depositing ice chunks on my kitchen floor every time we opened it. An appointment for service was made for July 18, service never showed up. Another appointment for August 3 was made and again service never came. I called the 800 number on Aug 19 again arranged service for Aug 24 after hours so that we did not have to take anymore time off work. When repair finally looked at the fridge they said the door was not aligned and did not close so the frost builds up and breaks off onto the floor. This can be fixed with a new door that can take from 6 weeks to 8 months as they are not stocked and have to be made at a factory. The fridge constantly runs and is starting to leak water through to my kitchen floor and basement ceiling tiles.I called Maytag/Whirlpool on Aug 25 and the service agent told me the best they could do for me was extend my original warrant by 6 months while I wait for replacement part and they advised I purchase the extended warranty. The second agent named Gabby I spoke to advised me to call Home Depot where I purchased the fridge to see if they would do something for me. She would write down my concerns but had nothing more to say or do for me since the repair person deemed the unit repairable and a part has been ordered. I called Home Depot on Aug 25 and I spoke to Appliance Dept who told me the manager who could help me was off that day. He advised me to stick weather stripping around the door to seal the leaks. I said I was hesitant to do anything that may void a warranty and he agreed. He suggested I may get a loaner fridge but I have heard nothing yet. I want a replacement fridge.When you pay $2000 for a fridge it should be worry free for at least a year? I have been reading reviews and I am wondering why this is not a recalled appliance as this seems to be a very common problem. I am sad that Whirlpool is not standing behind this product. Home Depot has been in touch with me regarding this fridge issue and the lack of customer service provided by Maytag. They are replacing the fridge on Sept 9th 2016 and taking the old unit away. Home Depot has tried to get in touch with Maytag and they have not gotten a response at all about my faulty unit.The staff at Home Depot in Peterborough have been excellent to speak to and have apologized for the issues with getting service to my appliance. I am very grateful to them for their assistance and for following up with me in this matter. The downside is that I am getting another exact Maytag unit as a replacement so hopefully this does not start all over again. Home Depot has been a great retailer to deal with. I am very saddened to hear that even Home Depot cannot get responses from this manufacturer. I have also lodged a complaint with the Better Business Bureau.

I am very frustrated and disappointed with all of the appliances I purchased from Maytag, 3 1/2 years ago. The stove has never cooked evenly, and they replaced both heating elements, and it still does not bake properly. I just called customer service, because my pies for the holidays burned once again. They told me there was nothing they could do. I cannot believe a customer that spent this much money with Maytag (purchased a washer, dryer, microwave and oven), gets no help from the company. The transmission has been replaced in the washer, and is still noisy. The dryer is also very noisy. The stove does not bake properly, and the microwave quit within a few months of purchasing. The quality of Maytag is very poor, and the customer service is obviously poor too, when they said there is nothing they can do for me. I guess they do not care about customer loyalty.

I purchased a Whirlpool oven. It is still under warranty at present. I used the self-clean oven feature just before Christmas, it wasnt that dirty but I wanted to have it clean for Christmas. The glass panels on the door had no stain or grease on it, until I used the self-clean feature, and now there is black staining inside the glass. This oven is not even 9 months old, and you cannot clean in between the glass. My second complaint which I believe is a very poor design on Whirlpool’s end is that the steam vents are very sharp. When I went to wipe off the black splash panel just under the vent tube, I cut my baby finger twice!!! And it is impossible not to slice your pinky. I have been working with Whirlpool since this happened, and they finally issued me a new stove. I was to go back to where I purchased this product and pick another stove. So I did this yesterday and checked out all the Whirlpool stoves because the store says I have to purchases a Whirlpool. But every Whirlpool model has the same sharp steam tube vent, and I am presently waiting for the store manager to speak with his higher ups to see if they will let me pick a stove made by a different supplier. I’m actually really shocked to learn that this could end up being a battle especially after I took the manager to every stove in his store made by Whirlpool and showed him each of the vents and just how sharp those vent tubes really are. You would think he would want to be aware of this and deal accordingly. So I post this to warn any potential customers of Whirlpool to check that steam vent on the left side of the stove, and stay away from it as it is very sharp and you can’t help but cut your pinky finger when you wipe across the stove.

I purchased this relatively expensive range and could not have imagined how dissatisfied I would be. The Aqualift cleaning technology does not work. There is no way to clean the oven door. They stress not to use oven cleaner, but as the Aqualift system does nothing to clean the oven door, there is no choice but to use oven cleaner, which they say will ruin the oven coating. Also, the grates are very heavy and it is impractical to clean the range top. I wish I had researched further; this product is a MAJOR disappointment.

Updated on 02/13/2021: Maytag stove purchased 15 years ago for about $500. Replaced mother board about 5 years ago which wasnt cheap, but otherwise, stove has performed with no problems and still looks and behaves like a new stove.Original review: Our 6-7 year old well cared for Maytag range oven recently stopped working. After a service call for diagnostics, it was determined the electronic module controlling the clock and all oven functions was dead. We were told by the Maytag service tech the module cost was 300$. That cost plus labor for less than an hour, plus the 60$ diagnostic visit came to almost 500$ which is close to cost of a new stove. The technician answered yes to my question, Do you replace a lot of these? He also said the cause may be power fluctuations making me think that surely there is a way to prevent this kind of failure. So, since the price seemed exorbitant, I wrote Maytag to inquire about causation/prevention, etc. I received a fairly prompt and polite reply with totally no explanation. I wrote another email with relatively the same results. I dont recommend buying an electronically controlled Maytag stove.

We bought a Maytag gas range in Feb of 2011. Shortly after that, we started having an intermittent problem with the oven not maintaining the temperature. It sometimes would not heat up to the proper temp or sometimes would get there but not maintain it. We have had several service calls all for this same problem. Each time they would replace things... nothing worked! We called Maytag and they said they wouldnt replace the unit until the same part had failed 3 times. Well, the service company came out 5-6 different times in the first year and replacing the main panel twice and the sensor and some other thingies I dont even remember. Pretty soon the warranty was running out, so I bought an extended warranty due to the fact that the unit had never been fixed. They sent out two different service companies who also were unable to fix the unit. It is now 18 months since we bought it, and Maytag refuses to do anything since it is out of warranty and the extended warranty company will only replace the unit up to 75% of its cost. So yes, we are very angry with Maytag and the way they wont stand behind their product and their total disregard for their customers.

The stovetop is very hard to clean and gets stained easily. The heat works wonderfully and the burners are great sizes. The left side with the adjoining burners is great. The double oven is fantastic. Heats relatively fast. Another negative is the button controls. You have to push so hard for it to register. Its painful. Not the best way to do it. Just setting oven temperature is difficult. Wish that was different.

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

I purchased this oven about 6 months ago. This is my second Maytag oven which I had for 18 years. I am extremely disappointed in the quality of this oven. I did my homework and shopped around and chose another Maytag. First, the ignitor clicks and clicks but doesnt ignite. After 4-5 times I have to shut the oven off and restart it. But worse than that is the enamel on top. The quality is HORRIBLE. You cannot use anything but a soapy sponge to clean the top. With my last oven I was able to use anything (softscrub, ajax, the scrubber side of a sponge) and the top was shiny clean. My stove top is covered with scratches and is not even thoroughly clean. There are grease spots around the burners that if I scrub any harder Ill take the enamel off completely. Very, very poor quality. Will never buy another Maytag.

My husband and I are retired. In 2006, we purchased a Maytag stove, refrigerator and dishwasher thinking we bought the best. Since purchase, we have had repairs on all 3 appliances costing us over $1000. We are installing our 4th electronic control touchpad replacement today at a cost of $250.00 each. We had a new oven electronic ignitor replaced on the same stove. The compressor on the refrigerator had to be replaced! The drawer mechanism on the dishwasher had to be replaced. We will never recommend or purchase your products ever again!

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

First let me say I have used Maytag products for 46 years. A little over a year ago bought a new Maytag Centennial Washer (Model MVWC555DW) for a cousin which was responsible to looking after as he had been brain damaged since birth. Needless to say when I started having trouble with clothes not washing and having to bring to my home and wash was not satisfactory. This machine never worked right but until after the 1 year warranty could get by. Needless to say I will never buy another Maytag appliance but now have a Maytag washer/dryer, stove and dishwasher in my home. Maytag is Not the quality that is use to be. WOULD NOT RECOMMEND THIS MACHINE AND ALSO UNDERSTAND FROM LOWES THEY HAVE HAD A LOT OF TROUBLE WITH THIS MODEL.

Every appliance in my kitchen is Maytag. I went with Maytag because its made in America and now Im annoyed. The microwave died after about 5 years and since I had a spare, I have yet to repair it. I am just now removing the panel to see whats going on in the inside so I can replace whatever broken part is broken. The double oven I have Ive had to repair twice. Once I had to replace a capacitor on the board because it blew. It cost me zero to replace it as I have an old home theater system I part out. The next item was the control pad itself which I tried to repair but had to replace for $200. The dishwasher died after 6 years of use and after replacing the control pad (couldnt be repaired), it still didnt work. And I got a replacement from my wifes dad who was moving and had to get rid of his. Ultimate timing. I purchased a Maytag refrigerator instead of a Samsung like an idiot (which I suppose I am at this point). The fridge leaks water because the drain plug is jammed and it will take a lot of work to get back there to unjam it. I think Maytag wants to sell you expensive parts that are doomed to break after a couple years of normal use. They want to send repair guys out to your house to charge you to fix their junk. I cant wait to move and buy all Samsung products and do away with this Maytag relationship once and for all.

The middle piece of glass on my four-year-old gas oven shattered. It was not being used, but when I called Maytag, they told me that that was not covered because I did not have an extended warranty, and that I can purchase a new oven door and would have to pay the service person. I hope they go out of business. Maytag stinks, and everyone should know this.

Approx four months ago we got new stainless steel Maytag fridge, stove and dishwasher. Terrible, terrible, terrible. The dishwasher rack was broken, and the parts are plastic and hardly any room on the racks. The fridge had the wrong hinges and doors on them. We have been waiting for four months to have them replaced. Today we checked with Maytag and still not coming. The fridge makes a very loud humming noise it almost shakes the floor. This was some sort of compressor problem. Now the fridge is having problems with the freezer. It is freezing up with frost everywhere. The stove is terrible. I waited an extra month to get a convection oven which I have had before and this one is terrible. The double oven is a great feature if they work. They take forever to heat and if you do anything with the food you have reset the temperature? The top is the worst for cooking as the only one that works fast is the boost but then it slows down and you have a hard time cooking the food. The black top is very very hard to clean. I have owned a Maytag washer and dryer for the last 34 years. They have been excellent. Since Whirlpool took over Maytag they seem to have run the name into the ground and all the good service and products they had built up are now ruined. I told my neighbor a few years ago to buy a Maytag washer and dryer and they did. They have had nothing but trouble and are now having to buy new ones but not Maytag. It is a shame that with all the technology that Maytag has built up over the years is now gone. If you look at all the terrible reviews I dont think Whirlpool will be in business much longer with products and service like this. I still have a fifties fridge for pop and beer and it is the best fridge ever with no problems and my last fridge in my garage, that I replaced with this Maytag is still better than this new fridge. The service man that came to fix the fridge said we had to build in the fridge to keep the noise down. How come they never had problems with Maytag products years ago. I feel its all about the almighty dollar. They only last a few years and you have to buy expensive warranty. If you made them properly you would not need warranty and they would last for years like before. If anyone knows if there is a class action suit against these companies let me know since all of us should not be ripped off and costing us time and money.

We had remodeled our kitchen in 2009. Bought new fridge and stove (Maytag). The oven door came off and cant get it back on. No matter how many times we tried, no way can we get it back on. I had to have my son to come and help us. No sooner did we use the handle to open the door off again. This has been going on for 3 years. **, well fed up. I called Maytag about this issue and they told me they would get a repair at my cost. The fridge freezes all the produce, cant regulate the temperature. Never ever will we buy any Maytag product again. Who knows what’s going to happen next? Oh, and the paint is chipping off of the grates of the gas stove.

CONSUMER BEWARE: Maytag is the WORST corporation to deal with. We have purchased a Maytag range from them recently. Unfortunately we have had 4 appliances delivered to us damaged from Maytag. The fourth time around we finally got a supervisor on the line. In order to expedite the situation. And the supervisor (Frank) refused to expedite or even call to try and move up the 5th delivery date. All he talked about was Maytag company policies to us. To make a long story short and I do mean long. Buyers beware. Maytag DOES NOT HOLD THEMSELVES ACCOUNTABLE FOR ANYTHING. Once the appliance leaves their facility they are not responsible for it. I CANT SAY THIS ENOUGH. DONT PURCHASE MAYTAG PRODUCTS.

The Aqua lift cleaning system is a complete joke. Have had to replace oven light bulb 6 times in 11 months. Control panel is completely discolored. Expected far more from a Maytag product.

We purchased a Maytag dishwasher MBD7749AWM on 03/15/12 from Home Depot. The control panel went out on 01/24/12 under warranty. The unit was down approximately 2 weeks waiting for parts and a second service call. Just six months later (approximately 08/05/12), the control panel failed again. Thinking that a trusted American, iconic industry leader such as Maytag would stand behind their product, I called for what I thought would be a covered repair. I explained to a supervisor that their panels have not made it 1 year in service. She assured me there were no out of the ordinary problems with the panels for my model dishwasher in one breath, then stated they were out of parts and on backorder for three weeks. Now the truth comes out, further telling me that the unit is out of warranty and nothing can be done short of sending out a repairman, that I would be responsible for parts and service. After further discussion, she reluctantly agreed to send me the part for free if I arrange the installation and told me that it was very simple to install. When the part finally showed up on my doorstep with no paperwork, it was wrong. When I called and complained for waiting 3 weeks for the wrong part because there was no quality control in their parts and shipping department, all they could do was say sorry. They told me just to keep the part they sent and they would send the correct part. I begged that they ship the correct part overnight and they adamantly stated that was not an option. Maytag stipulates their process only allows ground shipping from FedEx per their contract. Knowing I had no other option, I agreed and waited for 5-day ground. The part showed up 13 days later and delivered by USPS. Apparently, I was lied to again and the left hand has no idea what the right hand is doing. Apparently, Maytag/Whirlpool have an inadequate and poorly trained quality control system in place and their manufacturing and electronic divisions are surly lacking a strong management team needed to go in and clean house. Instead, the whole mess they have contributed to continues to haunt Maytag has continued to be made to believe its okay to produce subpar products while continuing the complete demises of a once trusted American, iconic industry leader all while living on the Lorals of twenty years past.Whirlpool would do itself and this country a huge service by just letting this brand die and thrown on the heaps of scrap steel headed for China where maybe they can copy and fix what they were not capable of.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

The microwave is 5 years 6 months since purchase model MMV4203DS. Fire started at rack clip left front rack, was cooking bacon. Called Maytag and according to them and manual on page 3 is only for 2-level cooking to avoid damage to microwave oven. DOES NOT SAY WILL CATCH FIRE OR THE RACK CAUSES SPARKS AND BACON SHOULD NOT BE COOKED IN A MAYTAG MICROWAVE. But according to Representatives of MAYTAG ** its my fault for not reading my manual. YES AND NOT HAVING THE SERIAL NUMBER THAT IS ON A PAPER TAG IN THE WHIP ZONE. The was gone from keeping it clean faded out. So I cannot be helped without the model and serial number.

I bought a Maytag MGR5605WW range on July 3, 2011 and it took till mid August before I received it. Right away I noticed when I put a pan on the grates, I had to be careful so they did not slip off. Dangerous! Then I made a pizza, and when I pulled the rack out of the oven, the rack tipped down and the pizza slid down on the oven. Danger again! I went over to Menards and they gave me the number of A&E (1-800-771-3029). I called them when I got home and an A&E person said they would call me back. After a few more calls, no one ever called me back. I went back to Menards. They said I need to deal with Maytag. I am very concerned with the racks, and so is everyone else. They are cheaply made. Tonight I had a family member place the frozen turkey on the rack and it bowed down! Danger again. The grates have a few chips. This is a nightmare. What a piece of trash. I’m trying to get someone to respond. This stove is dangerous to my well-being, and I have no other choice but to use it.

I purchased a Maytag built-in microwave and oven combo in 2005 for my newly built home, but I did not move into the house until 2008. So the appliance has only been used for 3 years. The microwave stopped heating after only 3 years of use, which was for microwave popcorn mostly. I also purchased, at the same time, a Maytag cooktop. The knobs had to be replaced, a dishwasher, a rack and utensil holder had to be replaced and a washer dryer that doesnt work properly. I also purchased a side-by-side refrigerator which is okay so far. Im very disappointed in their appliances and they were expensive.

Bought new in 2006. From the beginning it shook a little. I could not use high speed without leaning against it and pulling upward on the unit. Maytag service workers came out and at first said they needed to balance it. That was not it. Then they said it was the drawers that I purchased as an option. Finally, one guy just straight up said they had no answer for it. Then came the day, last month, it was spinning and suddenly it started to rock and I ducked out because I thought the tub was coming through. I seen smoke. Yelled for the kids to get outside. With the phone in one hand calling the fire dept, I ran for the electric box & started throwing switches. Fire dept said that is what saved my house. Now it sits in my dining area because of a lawsuit I was never contacted about. No parts are available. Thats what happened when Maytag chose to send the business to China. Now they are back to making them in the USA but why would I buy again from a company that does not make good? Well I love blogging and Facebooking. I know 40% of Central FL because Ive lived here 60 years, plus my husband serve all of Orange County 35 years. This review will go out all over. Anyone need a tall table?

I purchased the Neptune HE pair because they are front loading and can be set on pedestals to raise them to a comfortable working height, plus the brand and reputation are both excellent. I like that the chimes can be adjusted from low to high, or turned off. The front loading washers clean so much better and with a lot less damage to items than washers with center agitators. Looks are secondary, thats for sure. Functions like warm/warm cycles and being able to adjust to whatever load needs to be washed is really most important to me. Any appliances with a good, proven track record of reliability with few repairs is high on my list. Expensive appliances should be made to last and be of durable quality! No cheap plastic or weak-looking welds or components, thank you! Quiet operation and dependable cleaning and drying are top in my book, and this pair has exceeded even my picky expectations in total overall performance. They are 11 years old now and look & function like new! I had one minor repair on the washer at 5 years, and not a single problem since. With front loading washers, its important to keep the door open a little when not in use so that they dont get a musky smell. Ive gotten into the habit of using laundry boosters to help clothes, sheets, and towels smelling fresh longer, and putting a small amount in the washer drum has kept my whole laundry room smelling nice. Purchasing the pedestal drawers to set the washer and dryer on added extra storage to my laundry and its much easier for me to load/unload them at this comfortable height. Im totally spoiled by it now, so when I use someone elses laundry room (when I visit) I am reminded how nice my own setup is.

Shortly after having this appliance custom wired and installed into the kitchen cabinets above our gas range, we found that the microwave no longer worked. The window where the digital clock shows the time instead Showed SE. I hit the clear button and the microwave once again worked. This happened again on many occasions and the clear button corrected this malfunction. Now this has happened once again but nothing Ive attempted clears the System Error or reboots the microwaves brain. Ive contacted many appliance repairmen but as soon as I mention Maytag they inform me not to repair the microwave as it costs more to repair than to replace. Ive attempted to purchase a new circuit board and repair it myself but no one has the part available. This appliance was purchased in April, 2009. Can anyone recommend a Microwave Brand as a replacement for this disappointment?

Paint bubbling & peeling off appliance: I purchased new double convection oven from Lows (Maytag). One month after delivery, paint began to bubble and peel off. Maytag takes the position that as long as the oven functions properly, the paint is simply cosmetic and the warranty does not cover cosmetic problems. Maytags position is that even if all the paint peels off but the appliance still functions properly, too bad for you!

We (family of 2) purchased our Maytag Bravo XL Washing Machine Model#MVWB880BW in Nov. 2013 for over $700.00. Last week, Dec. 2019, the washer would not finish the rinse/spin cycle. The clothes were still wet. I researched troubleshooting in the Maytag booklet included with the machine and tried everything. It still showed an OL on the readout. It was not overloaded as I only had 3 towels, 3 washcloths, and 3 hand towels in the washer. I tried just the rinse/spin cycle alone to get the water out of the clothes, but they remained wet, and the OH still appeared on the machine. When I called the place where we bought it, they suggested unplugging it, waiting and plugging it back into the outlet to possibly reset the machine. That seemed to work for 1 very small washload. The next day, I tried washing again and the OH appeared with the clothes still being wet. We had a repair person come out. The service call/diagnostic of $116.98 plus repairs of $304.41 plus $95.00 to install of the new Motor Control Board. I feel that cost is excessive for only 6 years of service. Before we bought this machine in 2013, I had a Maytag which lasted over 20 years with NO problems. I always thought Maytag was the best washer, but this experience has proven to change my mind. We went out and bought another washer rather than replacing the board not knowing how long the new one would last. Needless to say, we did not buy another Maytag. I do not feel I can trust the Maytag products anymore. After this experience, I did more research on the Direct Drive used in this particular model washing machine and found that it had been problematic. I would have thought Maytag would have offered a recall to avoid these costs/problems and avoid dissatisfied customers. Along with the original purchase of the Maytag washer in 2013, we did buy the matching dryer and are hoping the dryer will last longer than the washer. We shall see.... This has been an unexpected and expensive lesson.

We bought this range (model MER8700DS 1) March 25, 2015. Manual states when you use the oven first few times odor or smoke may happen and is normal. It also tells you this is not harmful but remove birds to another room because the fumes can kill them. Noxious fumes? Forget about the birds! Had to open up the whole house and go outside. Burned my eyes, throat and lungs. Day after day, repeatedly turned temp up to 400 trying to burn off what we thought might be a coating. No luck.Maytag got very concerned when I explained about the noxious fumes and had someone come out right away. Tech took it apart. He removed bottom (screwed in) plate that covers the bottom heating element. That plate gives the added ability to have 3 racks and make full use of the 6.3 cubic ft. capacity. Under the plate we found bits of insulation. We think that is what we smelt as it burnt up. He couldnt smell anything when he had it up to 400. So off he went thinking problem solved. Well, it still stinks. We will have Home Depot take it back. Oven takes forever to come to temp which we read in many complaints but thought thats minor. Dont know what oven to get instead since Whirlpool makes so many brand names. And other brands all seem to have their own problems.

Purchased French Door MF12269VM 22 inch from The Brick furniture April 1, 2012. Turned out to be a real April fools joke. Purchased extended warranty with TransGlobal for 5 years. First, fridge delivered after about a couple of weeks because it actually wasnt in stock. Naughty Brick lied about availability. Fridge arrives and after a service call from Maytag repair, they ascertain compressor doesnt work.Order fridge number 2. Two weeks later, get second fridge but lever for dispensing water is broken off. Order fridge number 3. Usual two-week wait and fridge finally arrives but the whole side panel is damaged. Send it back and order Fridge number 4. Service from Brick, Maytag and Whirlpool, terrible customer relations. Misrepresented delivery dates, supply issues, and operational damages.Fridge finally installed. Ice maker operates intermittently for the next year. Service techs from TransGlobal offer a variety of suggestions including changing filter, water pressure issues. Finally ice maker stops entirely in Summer of 2013. Is replaced after a month of waiting for parts of which the wrong part was sent. Ice maker continued to operate intermittently. Sometimes just a small of ice or no ice for a day. Finally in May after another service call, ice maker stopped working for about 4 days. Tech comes out and miraculously, it starts working again. A month later stops again and hasnt worked since.Contacted TransGlobal off shore call centre? And arranged to have an assessment to see if we needed a new fridge. Request declined and Maytag (Whirlpool) sent a tech out after another week. Service tech recommended new freezer. Waited a week for parts and arranged for Service tech to replace ice maker. Wrong ice maker part (for the second time) in less than a year.The latest trick from our possessed fridge is recent alarms from the temperature control. To say we are disappointed in this product, the retail experience, the quality of the manufacturing, the shipping procedures, the poor engineering and design, doesnt come close to describing the shoddiness surrounding this appliance and the service weve received.In conclusion, we are still awaiting an ice maker and are contemplating buying another fridge. What it is fair to say, we will never ever buy another appliance with their the Whirlpool or Maytag attached to it. Nor will we ever again buy anything from the Brick, or depend upon TransGlobal for repair services. Are there other Manufacturers and retailers out there who understand the meaning of service and quality. I certainly hope so. Otherwise Im going to invest in a good icebox.

I wish I had researched high efficiency washers before buying because of a name we trusted implicitly. Our washer does not get our clothes clean & cleaning it with Affresh is not enough. I have never had to work so hard at getting clothes clean! Towels smell musty, stinky. My husbands sweaty workout & gardening clothes smell worse, even with subsequent washes & his shirts have white spots from the detergent not even being washed out. The rinse cycle water just washes out the bottom of the machine while the clothes are plastered against the side of the machine. I do not wash my husbands clothes with anyone elses or it all smells and if he washes them twice, they still have that odor that comes from being dank. Even if I stop the washer to arrange the clothes on the bottom so they will get rinsed properly (gotta wait two hours for a load to finish) I have bought every HE laundry detergent on the market, every odor remover, vinegar, baking soda, bleach. For a year Ive been chasing my tail to do the dance that I never had to do with a top loader agitator Maytag that we had for 7 years and never had to clean once, but used unscented detergent that got the worst smells and stains out without much thought. Even reviews that I read about their amended top loader with an agitator are not very good.

I purchased my oven in May of 2012. Ive tried numerous times to use the clean cycle. There is absolutely no way it works. I contacted Maytag on 1/13/14 and their response was to explain the concept of AquaLift Technology as if I didnt already know that. They said I should use the plastic spatula (as if I had not already done that). They urged me to email whenever the need arises (as if that will do any good, they obviously acted like there was nothing wrong with their AquaLift technology). Someone should hold them accountable for their faulty product. Maytag is now a dirty word in this consumers vocabulary, and no amount of scraping ...with a plastic spatula will clean up the mess they sold me. I hope it breaks so I can go buy a product from a company where self-clean does not mean I am scrubbing (with no success) and running a clean cycle numerous times in an afternoon to try and get a spillover cleaned up.

I bought my Maytag Bravos washer and dryer set about 3.5 years ago when I moved into my home. There was a 20-year old set here that did work, but I wanted something newer and more efficient, so I donated the old set and bought these. Performance of the washer has always seemed mediocre, clothes dont get as clean as I think they should, whites are dingy, despite using hard-water additives and the correct HE products.A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel then start again, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. Its now up to ten F1 errors both at the beginning and end of the cycle. I dont have that kind of time to babysit my washer. I already have a full-time job.I have called Maytag/Whirlpool twice now, both times getting unsatisfactory answers. Even after escalating to the customer service supervisor, I was basically told that it is most likely the control board that is the problem and since Im no longer under warranty (that washer ‘is’ almost 4 years old, maam), Id either have to order the part myself from their supplier (total cost $250 + the risk of DIY), or buy their service package for about $350 which included fixing that problem plus one additional years warranty.I pointed out that for a major household appliance that I (over) paid for, I expect a life of more than 4 years, especially since I had a working 20-year old washer when I moved in here. Since when is this acceptable? I could understand if it were a wear-and-tear part, like a rubber seal or something that moved constantly and would eventually need replaced. But this is the electronics module, something that cant (or at least, shouldnt) be worn down or broken by use or even user error. This is an integral part of the machine, and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer.What angered me even further is that the customer service manager even admitted that models similar to mine had had similar problems, and a free control board was sent to those customers. But my model was not in that range of production, so clearly they have no fault, in their eyes. Apparently, its not even remotely possible that maybe when they determined the range of models they believed to be faulty, mine hadnt been in use long enough to display the same behavior? Maybe the range they selected is too restrictive and they missed some. From the volume of complaints Ive seen online, Id bet that to be the case.I asked to be transferred to their legal department, and was refused because we just dont transfer customers to the legal department. Well, I just dont buy Maytag or Whirlpool anymore, and Im going to do my best to make sure nobody else does either. Im replacing this ** with a different brand, one Ill be sure has tremendous reviews and a manufacturer that will stand behind it.

My Maytag refrigerator, model number mff2557heb, serial number 10375839gv, was purchased in 5/2005. Two weeks ago, this refrigerator stopped working. I called the Maytag technician and then right away came to my house and find out it is the compressor that needs to be replaced. He told me to search if it is under warranty. I searched in the internet Maytag compressor warranty and I found it and then called the Maytag representative. I told them I have found in their website that compressor of this Maytag is covered for 10 years but labor is not included. Then they asked me to fax it. I faxed the copy on 6/20 and they responded on 6/22. He said they received the copy and he said, Yes, it is covered for 10 years but you will shoulder the labor. So to make the story short, this Maytag representative scheduled Friday, 6/29 for the Maytag technician to fix my refrigerator. My husband did not go to work yesterday, 6/29, Friday, so he will be home for this Maytag tech. Maytag tech came at about 2pm yesterday and when he confirmed that it is the compressor that is the problem, he asked for the warranty paper. And when my husband present the proof, the copy of their warranty coverage that came from the Maytag website, he refused to work with my refrigerator because he said the one in the internet is not valid. It is really upsetting because I faxed the copy of it to them on 6/20/12 and they honored it. Thats why they arranged the technician to come to my house and then my husband did not work for them to work with our refrigerator and then asking me $79 for just saying that it is not covered by the warranty. I even gave them the model number and the serial number of the refrigerator so they can verify if it is covered. He said yes 10 years warranty on the compressor. In fact, two employees that I have spoken to both agreed that it is 10 years coverage except for the supervisor named Rachel. Her employees agreed to 10 years based on the paper that I have faxed them and it came from their website and they dont want to honor it after they sent the technician to my house. Thank you so much for your time and for reading about my grievances against Maytag employees.

My 2.5 year old hood range microwave stopped heating. I called repair guy, he charged $115.00 for barely a half hour and said he tightened a part and it should be fine OR the part would need to be replaced. Guess what!... That night microwave is still not heating anything. Dinos Appliance Repair is responsible to repair but Maytag doesnt stand behind its product. How do I get my money back when a repair doesnt repair anything? I wont buy Maytag again or GE.

We bought the Maytag Bravos Washer and Dryer set in 2013 after extensive reviews as well as the brand recognition to replace my at least 20 year old Kenmore washer/dryer. At first we were very pleased. The ability to do bulky loads was great and the high spin cycle left the clothes almost dry. In 2018 (keep in mind, just 5 years!) we started to hear a grinding sound in the washer when on rinse cycle and the dryer would randomly turn itself on! Strange but true. I called Maytag Canada and they sent someone right away. They had to replace the motherboard on both the washer and dryer as well as the drum and gears on the washer. Fortunately this was covered under warranty.Fast forward 1.5 years. Same issues with washer...technician came and could not identify the problem, although I did tell him it was the same as 1.5 years ago. I ended up recording the sound and asked them to resend technician to the house. After further diagnostics, yup...same problem. Two days went by and I received a call back advising me that the cost to repair would be over 700.00, not covered by warranty! I escalated to management, to no avail although they did offer me 15% off my next Maytag purchase! Needless to say I have ordered a brand new GE from Costco, arriving tomorrow for basically the same price to repair the Maytag. I will NEVER purchase another Maytag product and will advise anyone who cares to listen to me to do the same. Huge disappointment in the Maytag product, brand name and customer service. 10 year warranty? Not likely...stay away.

I bought a Maytag 4452BDW stove, the more button is not working. I did my research and was not happy to see this is a common and reoccurring issue with Maytag Stoves. The expensive of the part that too often fails again along with the cost of the service man to repair it places the Maytag as low quality at a high price. I am hoping to see a company that stands behind its product by addressing this correctly and promptly. It would be a pleasure to have my faith restored as it should be by Maytag.

Like many people here, I have a Maytag Dishwasher Model # MDB7749SBW3 Serial # F40107007. We have had this dishwasher for about 12 months to 18 months. The first indication that there was a problem was some of the lights were acting strange. Then the dishwasher starting going nuts. I removed power from the unit thinking that maybe the controller became confused. The problem persisted. I would hit buttons and either nothing would happen or something completely different would happen.I take the dishwasher door apart and remove the touch pad. I notice some discoloration on the ribbon cable. I remove the glued on front panel to look at the electronics behind it (see pictures) and I see some discoloration there as well. So using my multimeter, I find that there is a direct short between pins 4 and 5. I vigorously flex the cable at the point of discoloration and the short goes away. So at this point, I doubt that I can get just the flexible circuit strip so Im going to have to pop for a new touch pad assembly. I didnt go further in the measurements as there was no point since I already detected one failure. Furthermore, I inspected the computer control unit and I did not see any obvious signs of corrosion or discoloration anywhere on the processor board. So it appears that there is no problem with it.Conclusion: Many people are at a disadvantage when it comes to electronic devices. In my professional opinion, this is clearly a failure of the insulating material of the ribbon cable due to environmental contamination. Visual inspection shows that corrosion of the conductors is clearly evident. About Me: I have been an electronics technician on and off for over 20 years now. I have a 2-year college degree in electronics technology and I am currently in school to become an electrical engineer. In my house, when something breaks, I fix it.

Freezer leaks water all over the kitchen floor in front of this $1900 piece of garbage. My husband disconnected the water line (for in-door water and ice cube dispenser) and it STILL leaks water. I can vaguely remember a time when the purchase of a refrigerator (manufactured in the USA) wasnt necessary more than once or twice in the average persons lifetime. This Maytag refrigerator is our second french door fridge in 5 years. The last one was an LG that had a shoddily designed and manufactured compressor that sounded like a diesel engine idling in our kitchen. Of the two, this one is equally defective but doesnt wake the dead when the compressor starts.It has become glaringly apparent the Chinese practice something I refer to as Cargo Cult manufacturing. Google Cargo Cult and youll understand what I mean. Briefly, they manufacture products that APPEAR to be refrigerators, washing machines, ranges, etc. However, lack of quality control and zero competition from companies that provide a well-made, quality product that lasts more than a year or two allows and encourages these slobs to continue pumping out what appear to be appliances until the consumer plugs them in. Thats when the fun begins.

I bought a Maytag laundry set (washer and dryer, models MVWC565FW and MEDC555DW, respectively), and I concur with the fact that this is the WORST laundry set I have ever owned. The clothes came out of the washer extremely dry and did not come out as clean as expected. In addition, clothes came out with strange spots, especially the dark ones. Now, we wash our dark clothes with fear of damage them. The dryer is also pathetic. I put in a normal load on high for 60 minutes, and theyre still very damp. Sometimes I have to repeat the cycle 2 or 3 times. When I compare it with my old laundry set, this is extremely disappointing. And to make things worse, the customer service department doesnt answer you. I sent them a mail, on February 2018, and a month and a half later, I havent heard back from them.

The stove functions are excellent and the temperature of the burners and oven causes the food to cook even. However after about 6 months the heat from the burners causes the coating on the stovetop to burn like its baking and it cant be cleaned. Now the coating around the burners is horrible and burnt.

Do not buy this refrigerator!! It’s small on the inside but to top it off the vent is on the left side, not in the back, so everything freezes on the left side of the refrigerator. Plus they positioned the light right in the front at the top so you cannot put a gallon of milk or anything tall. Not orange juice, apple juice, nothing!! Horrible design. I’ve had the repairman out, he said he couldn’t do anything about the freezing on the left side unless he turned the temperature up on the fridge and on the freezer. We tried that & The ice cream was so soft, almost melted. The problem then was the temperature was too warm for milk and other items. Not a recommended temperature to keep cold items. He said I would have to keep everything away from the back & the left side to use it without freezing my items. I’ve lost a lot of food because of this. Very unhappy with this refrigerator!!

We purchased our Maytag gas range in 2015. Within 6 months we noticed the clear coat and paint was defective, we called Sears, they allowed us another range top and replaced it but told us our warranty was up in a month and they would not replace another. The stove always looks dirty because the clear coat and paint have bubbled up and it is clearly a 100% manufacturing defect that should be recalled.

I purchased an over the range microwave (OTR), boxing day 2018. It failed January 2021. It worked great before failing. The issue with Maytag/Whirlpool is their service. I told them before they came out that I was only interested in having it fixed if it could be done that day. They checked that they had the parts and said they could do it, so I moved forward with the appointment. Well they didnt fix it, and said that they need to order a part, which they said would take several weeks. They are trying to bill me the service fee $167, and expect me to wait a month or possibly more to get the part and fix the microwave. Now Im faced with having to pay a service fee for something not fixed and buying a new microwave. Lesson: Never try to repair, cheaper to buy a new product. Other lesson, never buy Maytag or Whirlpool product again. Despite what is on their website and advertising, they have terrible customer service.

We had a $1700 French Door refrigerator delivered in January, the ice maker worked for 4 days. 4 service calls by 2 different companies and still not making ice. After fighting tooth and nail, we finally got a new fridge.. upon installation the water in the door spewed everywhere and would not shut off, so yet another new fridge was ordered and delivered last Friday. So, after countless hours, missed worked wages and having strangers in and out of our home 7 times, they offered us a lousy $50 prepaid gift card for our trouble. After a little long drawn out fight, they increased it to $130 and said that was their maximum compensation: Shame on you Maytag, that values our time and hourly wage at about $1.00 an hour. NEVER AGAIN!!

I purchased this range from a Maytag outlet in Nov. 2006. No problems with it until Nov 2015. The oven igniter failed. This was serviced locally and replaced in an efficient manner by the local service tech. All is good until 2 days later when I decided it is time for an oven cleaning cycle. I set the cycle for Medium Soil (3hrs). After the conclusion of the clean cycle, the oven (bake) would not work. Called Maytag service, the service tech replaced burned up oven wiring as well as the igniter again. However, the cleaning cycle had taken out the gas safety valve control as well. I am now told there is no replacement oven gas safety valve unit available anywhere. I even called Maytags 1-800 number and searched online only to find the part on backorder and not available.I find this particularly frustrating in light that I spent over $1200 on a Maytag product I thought would bring way more than 9 years of service before it is deemed unrepairable. The average gas range lifetime is 18 years. In my opinion, not a good return for the investment. Its a shame because the rest of the range works and looks fine, which is now destined for the dump. I am replacing the Maytag with a $550. Frigidaire with manual cleaning. Will never buy another Maytag appliance or a self cleaning oven again. If the self cleaning feature has the potential to fry the controls, why would they offer such a feature, or why couldnt they warn one of the potential failure.

Im furious beyond belief with Maytag. Im furious at myself for being stupid enough to purchase all new Maytag appliances when I purchased this home as I had horrible experiences with them in my former home. This concerns the Maytag over the range microwave oven model MMV4205AA. First of all, within 6 or 7 months after purchasing it while cooking a frozen dinner, the turntable just cracked in half. Maytag wanted $89 to replace it. I knew when the turntable cracked that there were more issues to come. That is not normal in any way for that to occur in a microwave.Problems continued, of course, and with each call to Maytag, they would say the same thing the microwave is out of warranty and refused to assist me. Its not some little table top thing that one can just toss out and buy a new one. I paid about $400 for it from Home Depot. Last week, without it even being turned on, it just stopped working. I checked the electrical supply and conduit to make sure that was okay. I called numerous service organizations who told me this sudden breakdown when the microwave isnt even turned on is a known issue with this model and several other Maytag over the range models. Ive called them (Maytag) three times in the last week and they refuse to provide any allowance and hear the same old thing, the microwave is out of warranty. I was willing to have them even just provide some assistance rather than replace the microwave. Ive been told by numerous service organizations that this is a known issue and that even if they repair it, it will occur again and again and Im best off purchasing a different brand, which I cannot afford. They gave me phone numbers for service organizations authorized to service Maytag products and this just goes to show how out of touch they are. They gave me one that isnt even in business anymore. How professional, not!Warning: Purchase Maytag at your own risk. I give you fair warning. Every single Maytag product Ive ever owned has been a problem. I will never, ever, ever purchase another Maytag product again. I would think just out of decent customer relations, that theyd repair this issue. To be honest, I dont really trust a repair as Ive been told it will happen again and again. There was no notice that the microwave was breaking down either. It wasnt turned on. One day, I went to use it and it just wouldnt work. Actually, I went to use the timer on it and thats how I found out it was dust. My advice is stay away from Maytag. If you read reports, there are more complaints on Maytag than any other appliance manufacturer in existence. Not only on their products, but their customer service too.

I purchased a Maytag stove model mer7765wb in December 2011. Now its November 2014. My display board caught on fire and its burn out. How can a Maytag product go out within 3yrs. I purchased it from Sears outlet. As Sears customer I am very disappointed in this product. Thank God I was in the kitchen to put out the fire.

We inherited this Maytag (Model MGR7662WW) when we bought our house this year. I love this unit. It cooks accurately, its easy to clean and its just rock solid in its performance. I never worry that the cook times are going to be off either. The oven racks are solid and the overall look is nice. Our friends and family love the center grill as much as we do. If I need to pull something off the burner I dont worry that Ill scratch the stove top with this feature. The oven heat is also pretty contained. Our old oven radiated lots of heat through the top. This one doesnt and thats a huge plus. The only reason Im not giving it 5 stars is that the grills are cracking (not the center one). However, I have no way of knowing if the original buyer damaged them or if its a defect in materials. They still work fine but I will need to replace them at some point. Given the cost of replacing them Ill wait as long as I can.

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

I purchased a Maytag Neptune 24” front load washer (MAH2400a) and 24” electric dryer (MDE2400AYW) on October 26, 2005 from Sears in Chesterfield, MO. In April 2011, the drum in the washer began to slush and grind. Water also began pooling around the machine. I called Sears and arranged for service repairman. Before he even looked inside the washer, the repairman wanted to give me a coupon for $50.00 off a new washing machine from Sears. After my insistence, he finally opened the washer and told me I needed a new drum. Because of the Sears repairman’s reluctance to look at the machine, I had another appliance repairman review it and was told that the water pumps for this model were defective. Any loose items the size of coins collected inside the pump and damaged it. I paid $340.00 to get the pump replaced. Ten months later, the dryer started smoking. After scheduling a service call, I was told the heating element burnt out and it would cost $360.00 to replace. It was then I noticed that the washer was leaking again. I took the front base cover off and saw mold growing under the machine. A little research uncovered that this set of machines has had many dangerous problems, from mold to catching on fire. There was a class action lawsuit filed and won by consumers in April 2005, yet I was sold this model in October 2005. I feel both Maytag and Sears knowingly sold me a defective and dangerous product. I would like to be refunded for this set.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

Our Maytag oven (not sure model) in the first year started doing crazy things with the oven computer. The oven would shut off and come back on and the display would be garbled. Also when my girlfriend tried to pull the turkey out, the rack fell off the left side and dumped all the juices into the oven. She almost got burned and there was a lot of smoke. The freakin rack should never fall off! Also our dishwasher is on its second control board. I lived by Mr. Maytag and his airplanes/helicopters at Crest airpark in Covington, WA. I wish I still did. Id like to ask him what he thinks of his crappy products. You get nothing for your money anymore. Im not sure but Ill bet both of my problems with these products have something to do with saving a buck by making this crap in Mexico or some other *** hole. Im just glad Maytag doesnt make airplanes or medical equipment.

I bought my Maytag Bravos washer and dryer set about 4 years ago when I moved into my home. The performance of the washer has always seemed mediocre. Despite using the correct HE products, clothes dont get as clean as with other washers I owned. Many times the washer becomes unbalanced, gets the UL code and I need to move my clothes around to get it running again. A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel and then start again several times, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. I read about other complaints and suggestions on the internet and tried pulling the plug for a few minutes to reset the control panel as well as turning off the breaker to reset the machine.After troubleshooting the problem for 15 minutes or longer, the machine eventually runs. Then I can run subsequent loads with no problem. After a week or longer of doing no laundry, when I try to start the machine, I need to go through the entire process of canceling the wash load and terminating electric power to reset the machine. I have called Maytag/Whirlpool and got unsatisfactory answers. I only wash two to three loads of wash about every ten days and sometimes even less. The 800 number for Maytag was automated and would only schedule a repair without asking about the specific problem or being able to talk with a person. There was no way to cancel the service call scheduled and I had to call another 800 number to finally speak with a Whirlpool representative who tried to help me. She connected me with A&E Factory Service to cancel the service call.Both representatives stated that most likely the control board is the problem and the cost for diagnosis would be $130 plus the cost of parts, which could run from $200 to $400 since Im no longer under warranty. I canceled the service call as the cost of repair would be easily be almost half or more of the cost of purchasing a new (and different) machine. This is the electronics module, something that shouldnt be worn down or broken by use or even user error. This is an integral part of the machine and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer. The customer service manager even admitted that models with other model numbers had had similar problems and a free control board was sent to those customers. But my model was not in that range.”I had purchased a Maytag Bravos dryer at the same time as I purchased the washing machine and the dryer had a problem within a week of the warranty expiring. A service repair person came to my home to repair the dryer as it was barely a year old and I did not use it for several months that year (due to other reasons). From the volume of complaints Ive seen online, the Maytag Bravos washing machines should have been recalled and repaired or replaced free of charge.

Never had a Maytag before I bought my house. So far the only complaint is there’s a broken piece that prevents the drawer from functioning. Otherwise, pretty good stove/range for the price. Do wish it was easier to clean without scraping anything up.

I would bought a Maytag Aqualift self clean oven. I just ran the clean cycle and it is just as dirty as it was before I ran the cycle. Absolutely nothing happened. Now I have the 2 cups of water at the bottom of my oven they said to put in prior to clean cycle, that I have to get in and clean out. This is absolutely unacceptable. I would like Maytag to get back to me asap and offer a solution. **.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

I love my gas stove. Mine is a five burner in white. Easy to clean and an accurate baking oven. Keeping the burner area clean IS a constant chore with a white surface. It would be lovely if the company made liners to catch the mess, but alas, I make my own with aluminum foil. This is an excellent stove and I’d buy it again! No buyers remorse.

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

Bought a new maytag gas range march 2013 model #mgr8674ab. The oven would not light at all. Would just click. Still under warranty. Called the service. They came and had to replace the controls in back. 2 months later the same thing, only this time it comes on and goes right back off. Then a week ago got it to light, used the oven and tried to turn it off and it would go off but immediately light up again. Scary to say the least. Another call to service. They are coming tomorrow. This is November 12 2013. I would not buy another maytag gas stove. There is something terribly wrong with this model.

I purchased a Maytag gas range about five years ago. After about two months, I noticed that the paint on the burner grates was flaking off. I called the company and they told me it was cosmetic. I have since bought two sets of replacement grates. I call the newest ones my dress grates, which I put on the stove when I am having company. I use the damaged ones for everyday cooking. Last year, the panel flashed. It locks constantly. And often, the door would not open, unless we pulled the stove away from the wall, unplugged it, and that cleared the computer. So, after months of unsuccessful door openings, the handle finally fell off completely. And the door locks whenever the oven is turned on. You have to finish your cooking, press cancel, and wait until the oven cools off, and then it will unlock. I have tried pushing aluminum foil into the latch hole on the door but have not been successful. Sometimes I just put a spoon in the door to keep it ajar while cooking. This cant be energy efficient. Of course, it is out of warranty. I saw a similar complaint about the burner grates. Also, the paint has chipped in several places on the cook top and the disks are all chipped. I am never ever going to buy a Maytag product. Oh, by the way, I called a repairman. I paid $65 for him to tell me that to replace the lock mechanism and the door handle, it would be $400. I can buy a new stove for that, but not a Maytag.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

Purchased a Maytag microwave/range hood in 2005. So yes, it is almost 10 years old but should the handle break off in ones hand? I would say poor material is the culprit. No use contacting the company by the looks of it... they dont stand by their product. Warranty says 10 years but broken handle would likely be cosmetic...

When my husband surprised me with a double oven stove I was leery. First Thanksgiving my thoughts were concurred as the 20lb turkey fell from the chinsey rack.....even a cookie tray with almonds fell down.... Unfortunately the lower oven is off by 1/2, no racks work in there. My biggest gripe is that the seller did not exchange it, just tried more racks. Now Maytag will not do anything but allow me to order more racks. This item is a huge piece of junk.

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.

My Daughter got me a Maytag oven with the AquaLift technology and is a piece of Junk. Half the time the Water is still there when the cycle is over. The water has made it between the front glass pieces and the finish on the top of the stove looks horrible, it just looks dirty. The knobs are cheap and the fake chrome finish is flaking off. Unfortunately Im stuck with it because I cant afford a new one... this was a gift to me because Im disabled and it was to make my life easier.

I purchased a Maytag range (YMER8875WS) on June 20, 2011. When I put my Christmas turkey in the oven, the rack fell! It seems the oven wall has gotten wider in the middle, so the rack doesnt stay in place. I have read several comments online about this, particularly relating to Kenmore ranges. This is a very common problem apparently caused by the oven liner bowing outwards.

I remodeled my kitchen last year. I purchased a stove, a dishwasher and a built-in microwave. Two days ago, I was trying to cook rice in the microwave. I changed the heat to 50% to cook the rice, started to cook and I heard this awful noise like a shot gun went off in the kitchen but the microwave was still going, I opened the microwave door and then I turned on the microwave again. At that time, it started to rattle on top of the microwave and shorted out. Black smoke was come out and I saw fire coming from the same area on the right upper corner. I got up on a step that I have and blew away the flames which were not big but if I were not in the kitchen, it may have caused a fire. I got the microwave from Lowes. Since it is almost to the year that I bought this microwave, they offered to replace it at no cost to me. Im getting the same model but Im purchasing the 2-year warranty just in case. I was told by the Lowes salesperson that this was unusual and should not happen again. We will see; its very dangerous. I had microwaves that lasted more than 10 years and had no problems. Maytag, where are you building your appliances and what about your product reliability? If I knew this site before I bought my appliances, I would not have purchased Maytag.

I purchased a new gas range in Nov 2013, but didnt use it until April because I was remodeling a house I had just bought. When I used it to cook Easter dinner, my meal was cold; the oven heats, then shuts off. Maytag has sent service techs 3 times. They have replaced the control board and the DSI module and ordered another part, for which we have been waiting over 3 weeks. Now they tell me it will be here next week. Maytag obviously cannot fix the NEW range, but they refuse to replace it. They deem it to be repairable though they cannot repair it. Customer service claims to be sympathetic, but will do nothing except schedule another service call and offer to extend my service warranty. What good is a service warranty if they cant repair the appliance? If youre smart, youll steer clear of Maytag and Whirlpool appliances. They are total CRAP.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

Purchased this double oven back in 2012 and have had to have the control valves replaced twice because of them jamming and snapping. The burners are undersized for cooking and it takes forever to get water to a rolling boil. The broiler in the upper oven needs constant attention when using it because food cooks unevenly and burns quickly. The lower oven is great, convection is awesome. I have seen the Maytag repairman more from my stove than I have for any of the other appliances I owe combined. Maytag should stick to appliances that only use water.

The ceramic coating on the interior of the oven cavity in the top oven, which I use the most (may actually happen to the lower oven in time) has cracked in the exact pattern of the hidden element. When I spoke to the salesperson at the store, he wasnt surprised and said that it will eventually bubble and rust!!! Called customer service and was informed they consider this an aesthetic issue with no fix!!! They will not offer any remedy or compensation. Are you kidding me!!!

Bought new glass top Maytag electric range. Only used oven 7 or 8 times when I was unable to close the door. Had to wait 12 days for Maytag repairman. Has to order new parts. Still without use of oven. Says its a known problem the hinges holding the door arent strong enough. Last stove 24 years old. Never had a problem.

Refrigerator failed in less than 7 years. In August 2005, I purchased a new Maytag side-by-side refrigerator to match the Maytag appliances (stove, microwave and dishwasher) in the new house provided by builder. In October 2011, I called a repairman because of noise. The relay switch was replaced for $179. Now, I am told the compressor and defrost circuit board need to be replaced for over $700. I will never buy another Maytag appliance or Whirlpool. They make and sell crap and dont stand behind their crappy products.

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

The AquaLift Self-Cleaning is a very poor substitute for a normal high temperature Oven-Range. It gives as much work as an oven without any self-cleaning, as it does nothing to the sidewalls or the door. The minimum temperature is 170 Fahrenheit, too high to rise a dough.

I purchased a Maytag refrigerator (MBF2258XEB), stove (MER8674AB) and dishwasher (MDB7749SBB) on May 26, 2013. So far all three have been worked on. First, the dishwasher would not fill up with water after the trial run. Called the repairman out. A tag was placed in a position that was preventing the dishwasher from loading up with water. Granted, we should have taken the tag off, however, it stated not to. Lucky for me, I am still under warranty. Second, the refrigerator, which is a freezer at the bottom, started to leak. I thought that maybe we were dropping ice. However, I finally called and had the repairman back out. He knew exactly what the problem was because Maytag knew about it. There was a faulty plug. So in a matter of mins the problem was fixed. Lucky me still under warranty. Those two things happen within six months of purchasing these items. Now, the oven does not work. It heats up to the desire temperature but then cuts off. Called the repairman and he thought it might be the lower baking element. Unlucky for me, warranty has expired. So, $90.00 for service call. Received a called from the repairman, $120.00 for labor and $70.00 for the baking element. I purchased the baking element myself, $58.08 and installed it. Still does the same thing. Now I have another appointment for him to come back out and see what is wrong. Another $90.00! So far I have spent $238.08 on a $699.99 stove. I will never buy Maytag again. Depending on the amount to repair will depend on whether or not I go back to Sears and buy Kenmore. I had Kenmore for 10 years with no problems. I should have gone back to Sears for my upgrade. I did contact Maytag via email. I am still waiting for a reply. Live and learn!

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

I purchased this machine and after 2 loads it started making a very loud and awful noise. Maytag sent a local service person and he found a screw that had come undone and was in the motor. Since then there are a few strange noises that the machine makes during different cycles, usually involving spinning. Called Maytag and then sent repair person. This young man was non-verbal, was probably 20 and it was impossible to communicate and try to figure this out. Person sat through a full cycle and he said the noises are because the machine is out of balance. Well, why did the sync system not balance at the beginning of the cycle. No answer to that. He reported to Maytag that nothing was wrong with the machine.Machine is still making noises and I cannot wash a small load or it will still be wet at the end of the cycle. I am a widow and live alone. I dont wash large loads. So I called Maytag again. They dont care. Finally they agreed to send another 2nd opinion. I have a lot of videos of the machine making strange noises and the repair kid does not care...lots of blank stares from him. I highly suggest not going with Maytag. They dont back up their products and they leave you with a bad machine. My LG FL was perfect. Never an out of balance load. I could wash a single item with no problem. MAYTAG IS A TERRIBLE COMPANY.