I have a major complaint with the Maytag double oven design. With the smaller oven above, if you spill any liquid while taking something out of the top oven, the liquid drips down between the two panes of glass on the lower oven door. This makes it impossible to clean. Maytags reply - call a service rep and have him make a house call and take the door apart for you and clean it. Not warranty work so I would have to do this every few months. Also, when baking in the upper oven, cakes and cookies tend to overcook on the bottom as the dishes are so close to the element.

Does not wash. Only very small loads get washed even though it claims to wash bedding. Some clothes NEVER get wet. Many times the clothes have to be rearranged and re-washed AND extra rinse. Cycles are over an hour each (then multiply x2!!). Maytag service has been called MULTIPLE times. They replaced the touch pad then the computer board. Both times saying the machine works “according to design/specs”. This is a Very poor design. Maytag should recall this inferior machine as it does not perform the job it is being sold for.

I had a stackable Maytag dryer that was bought in 2016 but only used during the summer of 2017. Last May the dryer stopped heating. I contacted Maytag and they sent a repairman a week or so later. He identified the problem in the electronic control and ordered a replacement part. The part came and he installed it a week later. The part was faulty and he ordered a replacement for the replacement. It arrived a week later and also did not work. He said he had problems with replacement parts but contacted the technical service department at Maytag as he did the first time. The technical service person said there were problems associated with new software being not compatible with dryers in the last year and we needed a new control panel. I contacted Maytag again waiting the usual hour to get through on the phone. They agreed to replace the parts for free and ordered a control panel that arrived a week later. The technician installed both parts but they did not work. I contacted Maytag again and after waiting the required hour talked to a person who said she would contact the department who could arrange a replacement. They contacted me a few days later and said they would supply a replacement for $250. This was delivered a week or so later but they did not have a stacking kit and returned to the delivery company with the dryer. A week later they returned with the stacking kit but forgot the dryer. A week later they returned with both the dryer and stacking kit but the installer (always a different person) said he was too big to get in the space behind the dryer and that the venting supplied was wrong.I bought new venting from Home Depot and a new installer arrived a week later. He said the new venting was not necessary and in fact wrong and installed the dryer. It ran but foolishly I did not check to see if it heated and neither did the installers or if they did took off without letting me know that the dryer, like the one that was replaced did not heat. I discovered this a couple of days later when I tried to use it. I contacted Maytag and they setup an appointment for a new service technician to visit. I contacted Maytag again today hoping to get some explanation of what might happen next or some explanation. They had no idea but did inform me that they would not replace the new dryer but would start repairs again.

MER8700DH - Within 6 months, left rear burner stopped working and Maytag repaired it under warranty. Within next 6 months, and just before end of warranty, right front burner stopped working and again Maytag covered it under warranty. Within the second year of ownership, the oven was not working correctly and Maytag refused to cover it because it was off warranty. So I called a local appliance repair company who gave me an estimate of over $300 to repair it and basically advised against repair stating that this stove was a piece of junk. So I replaced it with a GE and junked the old one before it was even two years old. I filed a complaint with Maytag. At first they said they would go half on the labor, but then they said I should have bought the extended warranty and refused all further help.

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

I have had my stove since 2004. A problem I have had was when I asked it to clean the ovens, it quit working all together. A service person was called. Also sometimes when I turn on one burner, another one will turn on instead. Yesterday I turned on a burner to low, and it did not turn on at all.

I had a stove my mom bought for me 26 years ago. Still worked perfect. Used constantly. In 2018 my husband had to have this stove. Said no my stove my mom bought and still works perfect sentimental plus three children using it. Not one problem. So he buys this Maytag stove I didn’t like but don’t cook much warming things up or frozen pizza. Go to our sons for holidays. Always next day cook a turkey for sandwiches. Open the door which is too heavy. Wouldn’t close and called my husband. Got it semi closed. Said we’re not eating it. He proceeds to cook. Door opened. More turkey is in garbage. My husband started reading. I also did. Looks like these Maytag stoves are garbage. Make a lot of money for repairs. Now this goes to dump. No one stands behind their products. Is it worth paying to repair no.

We purchased all new Maytag appliances when we built our house. So far, the stove/oven has quit working and been repaired 3 times; its always the ignitor. The dishwasher has been fixed twice. The washer no longer spins out as it should. The refrigerator and dryer so far have run okay. I am definitely going to change brands with my new appliances. I will not purchase Maytag again. Its not what it used to be. I will do without oven this time, until I can buy a new one. Also, the dishwasher door has had problems from day 1, and now, it will not close at all. It seems like its off the hinge. Definitely, its not the Maytag of years ago.

CHRISTMAS morning Set oven to 325 for ham. Control board caught fire and burnt wires and burnt inside of rear cover. It got hot enough to char the wood wall behind stove. This could have killed my family on CHRISTMAS.

We purchased this double-oven range (model: MGT8775XW01) about 5-6 years ago. It came with some slight bubbling on the plate that the control knobs go through/are mounted onto. A few years later, the bubbling paint began to chip/peel off - revealing rust (its a white range). I bought some touch-up paint, but that didnt look very good. Now that entire plate is bubbling and peeling and makes the whole range look like crap. My wife swears well never buy another Maytag product...EVER! Shes ripped! I cant seem to find the replacement part to purchase. Lousy products!

I purchased a white Maytag gas stove over 12 years ago. It has been great and never caused any problems. I live alone and rarely use the oven. However, I use the stovetop daily for cooking. With continual use, it has a lot of nicks and scratches. It also has stains inside the glass oven panel that I cant clean. The glass would have to be removed in order to clean inside. This is why I give a rating of 4 stars. If I used the oven more frequently, I would notice if it had any problems with the temperature, proper cooking, etc. and could give a more accurate rating. I have small toaster oven and therefore, I cook practically all of my meals in the toaster oven.

Bought the Maytag high efficiency washing machine with the auto-sensing and deep water wash feature. It took some getting use to because of all the washing choices and different noises it makes. Auto-sensing seems to use very little water which is strange but clothes seem to come out clean. Best bet for me is like the old school way and use deep water wash and light load which is shorter and thats most efficient power wise but will use more water which is fine by me. Also bought the matching dryer and thats a 5 star review. Excellent product.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

We have owned this range for a little over a year. Oven will not hold correct heat. Have temperature sensor replaced under warranty. Did not make any difference. You can adjust temperature up or down according to actual temperature readings, but the temperature swings so much that it is worthless to try. Very hard to get food baked right.

Maytag Range Precision Touch Control 800 Electric Smoothtop - The racks in the oven fall down. I have replaced them with new ones but am having the same problem. I emailed my concerns to Maytag a few months ago but didnt get any response (so perhaps I didnt go to the right site). The oven was purchased in early 2008 and this is the only problem I have had with it. If I am extremely careful, I can bake cookies but if I try baking or roasting anything heavy, the racks fall. It is very frustrating but I was pleased, for lack of a better word, to see that someone else was having the same problem - at least I know it isnt just me. I will try contacting Maytag again.

Back a couple years ago, Dec. 29, 1983, I purchased a Maytag washer, model A209, and a Maytag Dryer, model DG110. Im still using them daily. The washer has given NO problems, other than the brake has taken to squealing. This causes nothing more than a notice that the load is done, so no repair is necessary. The dryer has proven more problematic, as I have had to replace the ignitor three times, the blower fan twice, and the motor (and belt) once. I still think I have gotten my moneys worth.

Bought new glass top Maytag electric range. Only used oven 7 or 8 times when I was unable to close the door. Had to wait 12 days for Maytag repairman. Has to order new parts. Still without use of oven. Says its a known problem the hinges holding the door arent strong enough. Last stove 24 years old. Never had a problem.

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

Our Bravos model mvwx0600xw0 is 5 years old. I have been dealing with the clothes getting tangled, dark colors full of lint and streaked since I had the machine. Recently the lid lock light has been blinking with 11 minutes left in the cycle. I thought maybe it was off balance, so I stopped the cycle and rearranged everything. Same thing happened again with the lid on the drain and spin cycle. After reading all the other reviews, I realize it is not worth fixing. So long Maytag. It was good knowing you when you sold quality!

I wanted a small stove that did what a large/standard stove could do. I was worried that the heat would be weak but it cooks my food amazingly well. This stove has all the bling of a simple stove for a smaller price and size for my tiny house.

I have had this range (Maytag MER8775AS electric range) for 36 days. The hot surface indicator light doesnt come on (bulb is fine) and the heat elements turn on and off on their own when I am cooking. 36 days! This thing is junk! I am going to see if I can return it, even though it is outside the 30-day window.

We purchased this oven (MGR5775QDS ) along with a Refrigerator/Freezer, Dishwasher and Microwave on 2007 when we remodeled our kitchen. Since then the Refrigerator had to be serviced twice, the Dishwasher had a recall for fire safety - repaired, but I still have a scorched bottom tray, and the oven after self cleaning once has warped and the racks will not hold anything with any weight without collapsing. Maytag sent me new racks about a year ago, but that didnt help. I grill most of my meals or cook on the stovetop but on the rare occasion we try and use the oven it’s a nightmare. We lost a Thanksgiving Turkey and Easter Ham and recently a lasagna and a glass pan. Every time we have one of these events I search the internet in hopes that there has been some kind of recall on this model. It’s not safe. When the 20 lb turkey came crashing down, my wife was nearly burned by the juices that splattered and the house filled up with smoke. Happy Thanksgiving from Maytag - everyone go stand outside in the cold for 1/2 an hour while we clear out the smoke in the house. Recently when the rack collapsed and hot lasagna came crashing down, the glass/pyrex tray broke and left a huge bubbly mess in the bottom of the oven. Yay Maytag, thanks again - ruined a dinner, broke a dish and since we can’t use the self clean option, spent the rest of the evening scrubbing out the oven... and eating takeout food on Valentine’s Day. Sounds like the perfect Romantic evening right? I am so sickened with this company. We purchased all Maytag appliances because of their reputation. But now they dont even stand behind their products. What a shame.

I built my home and bought all Maytag appliances. The freezer and fridge knock on wood have been repair free. Replaced control panel on stove for 400.00$. Washer after 2nd repair had to replace 600.00$. Dryer repaired once 95.00$. Replaced dishwasher with a new Maytag. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. This is the 4th repair. I have paid for 2 repairs out of warranty. 380.00$ the last repair. I did request some help from Maytag. They said no... My dealer did only charge me for the parts.

Please Do NOT purchase the Maytag Aqua Lift Gas Range. It does not clean anything, you will pay more money for a cleaning oven that does not clean any grease or droppings if you cook. This is not an Oven for any one, or family that cooks large meals or has gatherings. I had the technicians at my house over 4 times and they confirmed that this oven is not a self cleaning oven. It doesnt get hot enough as your self cleaning ovens. And MAYTAG did not want to hear anything, basically not clean much, but advertised as a self cleaning oven. Having been a Maytag customer for years I will never buy a Maytag product again. And we need to support American made, but not when the consumer is misled.

In a way, l feel fortunate and you will read why in a minute. l have been reading Maytag complaints specifically looking to see if what happened to me has happened to others. Apparently, it has. We purchased our Maytag range, model MER57750AB, in 2005. We too have had some repairs done under warranty. Unfortunately, we live in a day and age where technology isnt always our friend. The old appliances that were not electronically driven lasted forever; todays appliances do not. However, when something with potentially serious consequences happens that is not technology related, it rates in the who is the idiot who designed that? category. I am talking about the exploding exterior glass oven doors.Two weeks ago, the oven door handle on our range came unscrewed on one side. I continued using the appliance, planning on repairing it myself when l found the time. (I used to tinker around the garage with my dad when I was little and therefore, I have great repair skills in several areas.) Last week, I was standing in front of the stove when all of a sudden, the glass panel dropped from the door! It landed straight up on the floor and fell forward so the top edge of the glass landed on my toes (the toes that I had surgery on for six hammertoes last November and are still sore!). Needless to say, l was shocked that this happened, and even more so, I was grateful that it did not break or either of my two grandbabies were around at the time. Then, I looked at the glass and saw that it was attached to the door using only eight small pieces of double sided sticky mounting foam. I mean small! As I said before, idiot! Did they not think that the heat from the oven would eventually wear out the ability of the tape to do its job? I gave up reading after I found enough complaints about the mishaps with the glass on the oven doors to realize that there is a definite problem here. I did not see where the glass fell intact, as mine did. Therefore, I am suggesting that the exploding glass panels more than likely gave way, as mine did, and shattered when they hit the floor. Should there be a product recall for this? Absolutely! The question is how does a recall get put in motion? As others have stated, this could have been a horrible disaster had little ones been around. I pray that doesnt happen to anyone.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

#Mgt8885x500 Maytag Gemini. After oven heats up, racks fall. What should I do. This is a safety issue. Help, afraid to use oven.

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

I purchased a Maytag refrigerator (MBF2258XEB), stove (MER8674AB) and dishwasher (MDB7749SBB) on May 26, 2013. So far all three have been worked on. First, the dishwasher would not fill up with water after the trial run. Called the repairman out. A tag was placed in a position that was preventing the dishwasher from loading up with water. Granted, we should have taken the tag off, however, it stated not to. Lucky for me, I am still under warranty. Second, the refrigerator, which is a freezer at the bottom, started to leak. I thought that maybe we were dropping ice. However, I finally called and had the repairman back out. He knew exactly what the problem was because Maytag knew about it. There was a faulty plug. So in a matter of mins the problem was fixed. Lucky me still under warranty. Those two things happen within six months of purchasing these items. Now, the oven does not work. It heats up to the desire temperature but then cuts off. Called the repairman and he thought it might be the lower baking element. Unlucky for me, warranty has expired. So, $90.00 for service call. Received a called from the repairman, $120.00 for labor and $70.00 for the baking element. I purchased the baking element myself, $58.08 and installed it. Still does the same thing. Now I have another appointment for him to come back out and see what is wrong. Another $90.00! So far I have spent $238.08 on a $699.99 stove. I will never buy Maytag again. Depending on the amount to repair will depend on whether or not I go back to Sears and buy Kenmore. I had Kenmore for 10 years with no problems. I should have gone back to Sears for my upgrade. I did contact Maytag via email. I am still waiting for a reply. Live and learn!

Purchased a Maytag range with Aqualift technology in 2013 thinking it was a good brand and *happy* to find a new way to self-clean my oven. This turns out to be nothing but a joke and I am not *happy* with it. After following directions to the letter, there is some loosening of anything on the floor of the oven, but the sides and top are slowly being coated with more and more grease. Ive spent way too much time with my head in the oven trying to scrub stuff without using a heavy duty cleaner but feel I now need to resort to Easy Off as there is no other way to get it clean. I also dont understand why they tell you to remove the racks since there obviously isnt enough going on to even clean the oven... How would the racks be damaged? And now I believe there is a problem with the Dual Choice element where Im not able to turn the temperature down. Even turned back to the low setting, the pan cooks away like its on high. I have to keep turning it off and then back on in an attempt to find something similar to medium or low heat. Im so very disappointed in Maytag and feel this method of oven cleaning should never have been put on the market. Its a scam!

This Maytag oven has lasted my mom for over twenty years. Now after her passing the oven is now serving me and my family. Have had it soon to be three years. Just now having to replace one of the eyes.

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

We bought this stove because of the self cleaning oven feature. What a ripoff! The Aqualift technology simply does not do the job that it is supposed to do. As the lady of the house says, Self cleaning means clean it yourself. Whoever engineered this thing needs to go back to school. Adding insult to injury, we have adjusted the oven temperature to its highest and it still cooks so low that a cake has to be cooked for half as long again than the recipe calls for or the middle of it is still raw. We would like to sell the stove but would hate to burden someone else with this piece of junk.

Purchased an expensive brand new home which had Maytag appliances in it. After about 1 1/2 years the freezer bottom began to constantly freeze and drip onto my floor. I researched the issue and found it was common, simply thaw the area where it freezes. Did it multiple times, we do not overfill our freezer etc. We must take the ice out of the bottom every 4-5 days. My hardwood floors are destroyed now. We purchased a Samsung fridge freezer bottom when they first came out years ago, had it for 7 years, 0 issues, but it went with the house. Now my Maytag oven door is locked shut, also it takes a very long time to boil water. Maytag junk. I am going to buy another Samsung fridge tomorrow.

I bought my Maytag Bravos washer and dryer set about 4 years ago when I moved into my home. The performance of the washer has always seemed mediocre. Despite using the correct HE products, clothes dont get as clean as with other washers I owned. Many times the washer becomes unbalanced, gets the UL code and I need to move my clothes around to get it running again. A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel and then start again several times, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. I read about other complaints and suggestions on the internet and tried pulling the plug for a few minutes to reset the control panel as well as turning off the breaker to reset the machine.After troubleshooting the problem for 15 minutes or longer, the machine eventually runs. Then I can run subsequent loads with no problem. After a week or longer of doing no laundry, when I try to start the machine, I need to go through the entire process of canceling the wash load and terminating electric power to reset the machine. I have called Maytag/Whirlpool and got unsatisfactory answers. I only wash two to three loads of wash about every ten days and sometimes even less. The 800 number for Maytag was automated and would only schedule a repair without asking about the specific problem or being able to talk with a person. There was no way to cancel the service call scheduled and I had to call another 800 number to finally speak with a Whirlpool representative who tried to help me. She connected me with A&E Factory Service to cancel the service call.Both representatives stated that most likely the control board is the problem and the cost for diagnosis would be $130 plus the cost of parts, which could run from $200 to $400 since Im no longer under warranty. I canceled the service call as the cost of repair would be easily be almost half or more of the cost of purchasing a new (and different) machine. This is the electronics module, something that shouldnt be worn down or broken by use or even user error. This is an integral part of the machine and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer. The customer service manager even admitted that models with other model numbers had had similar problems and a free control board was sent to those customers. But my model was not in that range.”I had purchased a Maytag Bravos dryer at the same time as I purchased the washing machine and the dryer had a problem within a week of the warranty expiring. A service repair person came to my home to repair the dryer as it was barely a year old and I did not use it for several months that year (due to other reasons). From the volume of complaints Ive seen online, the Maytag Bravos washing machines should have been recalled and repaired or replaced free of charge.

Our home has seven Maytag appliances: an upstairs kitchen, downstairs suite and laundry room. All were brand new six years ago and what we thought to be good quality by the price we paid for them. We have lived to regret ever dropping a cent into Maytags business account, as we have had nothing but trouble with them. We dont have small kids or teenagers abusing them. Its just us and a very responsible single adult downstairs. And every time we turn around, one of them is costing us nothing but money and grief. Our first problems began with our upstairs fridge when it was only two years old. At that time, it cost us $400 and since then, it just goes on and on. Last week, our downstairs fridge quit, and today, our upstairs one quit. We have had work done on our range, as well as our washing machine and dishwasher. If you are thinking of buying a Maytag appliance, dont, unless you like to throw away your money. I couldnt believe when I looked up Consumer Reviews on Maytag appliances tonight that I would find only 1 out of 5 stars, and read all the terrible reviews written by angry consumers. Well, add me to the list because I will never buy another appliance from Maytag again, and am beginning to think its time to sell this house to get rid of these stupid, useless, pieces of ** Maytag appliances! Sorry, people, but I cant afford to keep replacing them!

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

Hello, I purchased a Maytag Bravos washer model MVWX655DW from the Home Depot in June of 2017. I can provide the receipt. Within 6 months I had a broken lid switch and the unit would not move through the cycles. Luckily, I had the ability to replace the lid switch at the cost of about $100 just for the part. The repair was fairly involved. This summer, the unit failed to agitate, upon much research, I learned the washer drive hub (which makes the washer agitate and spin) was worn out. It was made of plastic and it is quite a job to get the cover plate off and to replace this part which ranges in price from $20-$45. This is a fairly difficult job and I would not recommend it to most people. It should not be needed in a 3 year old machine. Upon inspection of the drive shaft teeth when I took the washer apart, I found the steel teeth to have significant wear. Why? Now, in mid-November, same issue, the plastic drive hub is worn out again! I was told maybe my shock absorbers for the drum needed to be replaced as the drum may be shaking too much. My previous washer was good for 18 years and I replaced it with this highly recommended model Maytag with the chrome basket. This is absolutely the worst appliance I have had and with every repair, I viewed many, many people with the same complaints and feeling that Maytag should issue a recall on these machines. I will be contacting Maytag and Home depot with my review. The HD installer also stripped the plastic valve one of the water hoses goes on that I had also to replace. A $40 dollar part. This took some disassembly but not as bad as replacing the drive hub every three months. Needless to say, I have to buy a new machine after 3 years of unreliability with his machine. A waste of $500 + of my hard earned money. Very, very disappointed. If I wasnt mechanical and able to fix this washer, it would have cost me hundreds in repair bills. I have receipts of the parts I have purchased for this unit. I hope your experience is better if you have owned one of these machines. Maybe I just got a bad one but many people have complained about this model so I dont believe I am alone. I hate to see good people spend their money on poorly constructed machines. I certainly expected more than 3 years out of a brand new appliance. Maytag and Home Depot have lost a good, long time customer unless they want to make it right. Please feel free to contact me.

I seem to be just another unhappy Maytag microwave oven customer. The SE code indicates a bad/faulty/short in the keypad. It seems this is a very common issue so buyers beware! If I dont get this resolved, I will no longer buy Maytag/Whirlpool products.

I would bought a Maytag Aqualift self clean oven. I just ran the clean cycle and it is just as dirty as it was before I ran the cycle. Absolutely nothing happened. Now I have the 2 cups of water at the bottom of my oven they said to put in prior to clean cycle, that I have to get in and clean out. This is absolutely unacceptable. I would like Maytag to get back to me asap and offer a solution. **.

Maytag AquaLift Oven #YMER8880BW - The aqualift technology does not clean the oven. It is sorely inadequate. I bought Maytag because of its reputation. This range should be recalled as should all their ranges with this useless technology. Buyers BEWARE! Do not purchase any range from Maytag which advertises Aqua Lift technology. This purchase has soured your reputation Maytag. I also purchased a fridge with the stove. I will NEVER buy a Maytag product again. I also would like to ask frustrated and disenchanted readers how they are getting their ovens cleaned. What product(s) can be used. Maytag - complete FAIL!!

Dual oven - one is a convection oven. Never used the bottom drawer so that was wasted on previous range. I purchased a white appliance to match my others. The white stove top is a pain. Too bad it wasnt black. I checked this model online and found a good price in the city. I contacted the local Home Depot and they did a price match less 10% - all a bonus. The ovens work great although I have not tried the self clean. I have read that similar models have problems related to the self clean feature - high heat and circuit boards. My plan is to have a fan directed at the top of the stove when I use it and the range hood fan going. The convection oven is great - hard to mess up a recipe with that. The dual ovens are truly a great feature - strongly recommend. The keep warm is great also - nice to have two things cooking at the same time. That being said - the bottom oven is low, but that is worth the extra cooking space.

I bought a Maytag range (MET-8775) last year, because my wife loves to bake and wanted the double oven. The oven never did brown properly, despite trying different temperatures and cookware. So, I called the 1-800 number in the manual. I was told they would have a technician come out and check it, and they assured me it was under warranty. The technician arrived, and since it was close to the end of the warranty period, I showed him the receipt for purchase. I got another assurance that this visit was covered by the warranty, before anything was actually done. Well, he checked it out and eventually calibrated the temperature. That helped a little, but still, it doesnt brown very well. About a month later, I got an invoice from the service company that dispatched the tech telling me Maytag will not cover the visit under warranty. After a long call with Maytag (now Whirlpool, I believe), I was told that since the calibration instructions were in the manual, it wasnt covered! Well, why wasnt the thing calibrated to begin with? And your average customer is expected to have an accurate thermometer/gauge to set it and know whether the temp is off or not? Why was I told twice that it would be covered? If either the lady on the 1-800 line or the tech who came had told me this wasnt covered, I would have argued a case right then. As it turned out, I had no choice but to get billed for something I was assured was covered. And as I said, it still doesnt brown right; and we had tried different temperatures before. We are preparing a major kitchen remodel, and its hard to believe that Maytag/Whirlpool would so thoroughly piss off a customer and potential future customer over an $80.00 service call.

I had my kitchen remodeled less than 4 years ago with a Maytag refrigerator, Bosch dishwasher, and GE stove. I had a 1 year warranty, and purchased additional 2 years. The warranty ran out last year, and the refrigerator is not working. Maytag customer service said all they could offer was 1 year extended warranty for $300. I told them a refrigerator should last longer than 4 years. They agreed, but that is all they did. Ive read other online reviews, and it appears a lot of people are in the same situation (however my fridge is not on a recall list). I will never buy another Maytag product ever! My GE and Bosch appliances are working just fine.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

I just bought my Maytag Range model #MGR8700DS2 in August 2016. Bought Maytag because I always thought it was one of the best with the best warranty around. Now I am not so sure. After using it the first time, found that when you are baking anything in the oven the burner control knobs get very hot. That is because they designed the knob area to be right above where the heat vents out from the oven door. The knobs get so hot that you almost burn yourself if you touch them. This is a bad design in my opinion especially if you have any kids around. Even the sides of the oven get way too hot. This is also bad because of the tight spacing to your cabinets. I contacted Maytag about this and got a OH WELL kind of reply to my problem. You bought it and you are stuck with it. I would not recommend buying this model to anyone.

We finished a kitchen tear out and full remodeling. From top to bottom adding the Maytag double oven insert into our cabinets. We checked out reviews and MANY stated that the oven's fans were LOUD! But we've had them now for 4 months and the reviews do NOT give an accurate account in my opinion. My wife loves using the ovens for all sorts of cooking and baking projects and the units are NOT LOUD at all. You'd have thought from what we read about the ovens that we were making a bad purchase but that's not the case. Quiet, even cooking and a GREAT PURCHASE. If your ovens are loud when cooling something must be wrong! Or maybe we got LUCKY!? I don't think that's the case at all but then I haven't used other's ovens only ours and we are pleased!!! 5 STAR for sure.

I purchased the gas stove in June of 2012 from Home Depot, along with a Maytag microwave (Model MGR7662WB4). Home Depot installed both items. After trying to reach into the microwave about the stove, the knob would turn itself on with me brushing up against it. This happened several times, and one time the flame shot up and I almost got burned. The last time it happened, I did not realize that the knob was turned very slightly and gas was coming out of the burner for several hours. If it were not for a friend stopping over, I would not have considered the odor being from the stove. I assumed that the drains were probably backed up and started to add cleaners to the toilet bowls. I had to open the windows for several hours to get the smell out. So I called customer service 2 times. The first person said I would have to pay for the call if the problem was not Maytag and I said, “Forget it.” Then I went into Home Depot and the salesperson in there gave me another number to call for service. They came last Friday and said that he had seen at least 10-15 calls about this and since the unit was working as designed and no recalls, there was nothing they could do. “Just wait and see if a recall would be put into place and I would be on the list to fix it. In the meantime just keep the knobs off (which I was doing already out of fear).” My sister just bought a Whirlpool gas range this summer as well and asked if I could try her knob and it worked perfectly. Again I called CS and was told they could not send me those at no charge and that it would cancel out the warranty. So I asked her what I have to do before I or someone else gets injured and she said that until there was a recall, there was nothing they could do. I told her I was going to contact Consumer Report as well as Pam Zekman on Channel 2 news in Chicago. End of story; I still have the problem and no knobs on the new stove. Anything you can do to help please contact me, and thank you in advance.

I bought my maytag stove model MGR7662WS on January 30, 2011 and have had it serviced 3 times... same problem. I set oven to 350 degrees, put food in oven and later check on food only to find the temperature reads 350 but the oven is cold. Food is not cooked and it smells like gas. I turn it off and turn it back on and it does not turn on most of the time. Service guy keeps replacing parts and says he will replace the same part he just replaced last week. He says sometimes the part comes out defective. I think the stove is defective and I have thrown away so much food because it does not finish cooking and smells like gas. Its so frustrating because my Thanksgiving was ruined two years in a row due to turkey not cooking.

This review is for a Maytag Gemini MGT8775XW 30 Freestanding Double-Oven Gas Range w/ 5 Burners. I cannot believe the amount of problems I have had from this $2000+ range. Within just a few weeks of getting it, the paint started scratching off the surfaces nearest the heat. Then, the plastic cover over the digital display and controls bubbled up due to the heat of the broiler being in use. They designed it so that the heat escapes from the oven right in front of the control panel, so when you want to adjust temperatures on the control panel, you chance getting burnt from the hot air every time.The very worst design are the manual knobs for the burners on the front. They are at an angle, and if you look at the oven straight on, you see they are higher than the burner surface. A hot pan that overhangs the burner cooks the knobs. The plastic interior of the knob lacks any kind of heat resistance and actually starts to turn soft, keeping you from being able to turn off the burner at all!Most dangerous of all, the knobs are frighteningly easy to bump, pouring gas into your house. We have had this problem multiple times. Today, my dog must have wanted to investigate the top of the stove, because when I came home, the burner was on, had burnt through a pot on the stove, and was just at the ignition point for an item sitting next to the stove. If I had come home 15 minutes later, my house would be in flames right now. I am having to air out my home as I type this. I am DONE with this dangerous oven and will be shopping for a new one, and it certainly wont be Maytag.

I bought this range Nov 2019, beautiful range that’s it. Stove top scratches very easily and hard to clean. Oven racks rust, got them replaced on the guaranty they still rust. Oven dirty never gets clean, If I could afford it I would on the curbside. I wouldn’t even give it away. 3 oven in 48 years of marriage, worst oven ever.... Sure would like a full refund, I mean 1500. What a ripoff.

Range is at least 20 years old and everything still works w/o issues. Our model has an upper level and a larger lower level that is a convection oven also. The top one heats up real fast which is great for quickly cooking and reheating. The lower one is large enough for everything else.

I purchased a Maytag gas stove. Right away I noticed the oven racks would sag in the middle pulling the back corners to pull away from sides dropping the rack down on top of rack below. I got a hold of Maytag and they sent me out a set of 3 new oven racks that were exactly the same as the ones I had. I have been fighting with them for years. I called Whirlpool today who make Maytag and was told its off warranty and that I can order another set of oven racks at a cost to me. They would be the same as I have. The racks are so cheaply made and cannot stand even a few pounds. The finish on the stove also chips very easily. You rub a pan up against it and it scratches the white porcelain off. I spent a lot of money buying the dream gas stove I had thought, but only to be unsatisfied with my purchase. Buyer beware of Maytag products.

Three years ago, we purchased a gas Maytag double oven, it worked fine for three years, then it blew the breaker. When we turned the power back on, we could not turn the oven off. The control panel had to be replaced, dinner too. We had bought the extended warranty, so that was covered. Last week, after four months, it happened again. We placed an oven thermometer inside the oven and it is was higher than the maximum temperature of 600 which the thermometer could measure. We are currently awaiting a new control panel. Maytag used to be a good name, but recommend you to buy something else.

Purchased a Maytag Centennial Washer from Lowes. This is the NOISIEST WASHER I HAVE EVER HAD. Self Balancing, pretty much the way it is, YOU lift that heavy wet laundry and re-arrange to balance. It just slams around even moving the washer, until you do. This washer also doubles as a BLENDER. It SHREDS laundry. The agitator does not go all the way down and thus, clothing, towels, rugs... get stuck under the agitator, wind around and RIP. Have had hundreds of dollars worth of laundry shredded such as: shirts, towels, new rugs and it even ripped the waist off a pair of my jeans! The other laundry gets tied up on the stuck laundry and you end up with a twisted, ripped, tied up Laundry Ball. It will not wash or rinse well when it does this, naturally. Lowes: The salesman knew about all this, and sold it anyway! He had one and got rid of it. Gee thanks Lowes and Maytag, for the worst washer I have ever had the misfortune of owning.

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.

We have had our oven for seven years this past October 2015 and has now been down for three weeks. Last February 2015 (8 months ago) we had to replace the bake igniter because the oven would not get up to temperature. The most recent incident happened a few days after Thanksgiving (2015), I was cooking dinner and noticed that the oven was not reaching desired temperature. I then opened the door to see if it was hot inside the oven and when I did it must have ignited making a huge poof and flames came out at me! Thank God my 12-year-old daughter had walked away from cooking with me to answer the telephone because the flames came out exactly where she had been standing!!!I contacted Maytag and explained what had happened and how we could have had an explosion or someone couldve burned. The first questions they did ask me was if anyone was injured or any damage to our house?!?! I was happy for that however, it also told me that this has happened before! They called the Maytag repairman in my area and supposedly made it a priority call in which he could not come until 12/10 which was two weeks after this happened. Therefore, my husband and I contacted a different appliance man who came out and told us it was the temperature sensor. Since fixing it, the oven works ok and cooks properly however, when initially lighting/igniting it is extremely loud and makes a very large/huge poof! Its as if the oven is filling up with gas and eventually lighting! The other night when I lit it to show my husband it was so loud that it rattled the door and he immediately turned off the gas to it. I googled this and it said that its basically a mini explosion where the oven is filling with gas and then igniting! Its to the point that we could lose everything we have worked for just to make a meal! We spend over a thousand dollars on our beautiful stainless steel convect oven. Its gorgeous and when working works great however, Im petrified to use it now because Im scared to being burned or exploding! Now we start over and yesterday on Sunday I contacted the original Maytag repairman who said to call back Maytag again and hell come immediately. Maytag originally told me on the phone that they would cover labor and the service call however, ironically enough they did not write that in the dispatch order! Im outraged! What will it take before its safe for our family and home! My husband is ready to junk it and buy a GE however, we do not have the money especially before Christmas to do so. Oh and let me add that the first week we had the oven we had to call them for the window seal to be replaced because it was hanging. So now seven years after owning it and 10 months apart we are having major issues. What happens if its fixed and a year later it happens again? It could explode in our home!!! SCARED & IRATE WITH MAYTAG & WHIRLPOOL.

In 2013, $1850.00 I purchased a Maytag double oven, $700.00 Maytag dishwasher, and a Maytag refrigerator for $2200.00. I have had nothing but problems with all of them.... The oven locked up on me had to call a repairman to fix it. Ive had to replace the control panel on the dishwasher... And the refrigerator!! (WHAT A NIGHTMARE) In 2013 just received the appliance they had to install a heater in the ice maker because there was condensation. 2014, Refrigerator dead.. Repairman had to replace interface and control board.. 2017, Icemaker crashes and had to be replaced... 2020, Now here we are again Ice maker crashed again! (JUNK). My wife told me that she has had nothing but good luck with Maytag appliances... Never again.

I purchased my Maytag gas range (model number mGR7665WB) on Thanksgiving 2011! It worked fine until May 2012. Then the bake function just stopped working. If I select bake, the temperature fails to rise above 100F and a sickening gas smell fills the kitchen! PC Richards, where I purchased the product from, sent a repairman who took two weeks and two visits to fix the part! Everything was working fine until six months later during cooking for a full house on the day of my daughters birthday party. Same problem, bake function failed again along with gas smell! I was pregnant at the time and very worried about the gas smell! We had to leave the house a few days after that due to the hurricane and when I returned, everything worked great for a few weeks only to fail on Christmas Eve leaving me to cook the meat for our Christmas Day dinner in a neighbors house, highly embarrassing and inconvenient! Now Maytag and PC Richards are only able to repair at a high cost to me which I cant afford and feel I shouldnt be responsible for as this product has been consistently unreliable and possibly dangerous. I am especially concerned about the gas smell as I have a newborn and a 3-year old in our small apartment!

Oven door glass shatters after 6 years of having this oven and the company refuses to cover it. According to them it is not a safety concern. It is actually designed to shatter this way. Wow, thats comforting. Should be 0 stars not 1 star.

Bought new in 2006. From the beginning it shook a little. I could not use high speed without leaning against it and pulling upward on the unit. Maytag service workers came out and at first said they needed to balance it. That was not it. Then they said it was the drawers that I purchased as an option. Finally, one guy just straight up said they had no answer for it. Then came the day, last month, it was spinning and suddenly it started to rock and I ducked out because I thought the tub was coming through. I seen smoke. Yelled for the kids to get outside. With the phone in one hand calling the fire dept, I ran for the electric box & started throwing switches. Fire dept said that is what saved my house. Now it sits in my dining area because of a lawsuit I was never contacted about. No parts are available. Thats what happened when Maytag chose to send the business to China. Now they are back to making them in the USA but why would I buy again from a company that does not make good? Well I love blogging and Facebooking. I know 40% of Central FL because Ive lived here 60 years, plus my husband serve all of Orange County 35 years. This review will go out all over. Anyone need a tall table?

Refrigerator failed in less than 7 years. In August 2005, I purchased a new Maytag side-by-side refrigerator to match the Maytag appliances (stove, microwave and dishwasher) in the new house provided by builder. In October 2011, I called a repairman because of noise. The relay switch was replaced for $179. Now, I am told the compressor and defrost circuit board need to be replaced for over $700. I will never buy another Maytag appliance or Whirlpool. They make and sell crap and dont stand behind their crappy products.

I bought this MMV4205BAB microwave thinking Maytag was a good brand and I wanted an over the range type. Problems began when it would stop in the middle of a cooking cycle. I called the repairman as it was under warranty. It was decided by the repairman that the weight of thing was too great for its thin frame, not letting the door close correctly. I got a new one and it, from day one, would make a shorting sound every time anything was cooked, on the stove top, under it, while it was on. It finally just shorted out. I have a Maytag washer and dryer that are also junk. So, needless to say, Maytag, 3 strikes and youre out. I will never have another Maytag product and I let others know what a great product it is.

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

I can see by the comments on this page that the letter I sent to Whirlpool was in vain. I purchased a Maytag double oven gas range (MGT8775XW00) from our local Lowes. We were remodeling a home we had purchased. Unfortunately (as anyone whos been involved in home remodeling/renovation knows well), it took much longer than I thought it would before range could be installed. It was several months later before it was installed. First time I tried to use the top oven, it would heat to set temp (I assume) and then shut down. The larger bottom oven had erratic heating. I tried adjusting oven temps but it was a guessing game. We had Fix-Rite Corp out twice and they were puzzled by the problem. Two times, they replaced the control panel. After the second repair, it was decided the only thing to fix the kitchen was a complete gutting, new cabinets and floor. The oven was pulled out before I had a chance to use it again. By the time we got the kitchen finished and range reinstalled, I discovered the oven still had the same problems and the broiler would ignite sometimes and when it did, the flame would go out after 30 to 60 seconds and would not come back on. By this time, we were past the one-year warranty. After the first repair did not work, I tried to get Lowes to take it back and assured them I would purchase another range from them. They said they could not do that. Now I can see Im going to end up buying another range. Be assured it wont be Maytag and it wont be Lowes. I also own and use Maytag washer and dryer.

I purchased the Maytag double-oven gas range, Model MGT8775XS, in 2013. The quality of this double-oven stove cannot be understated. Performance? Terrible. Reliability? Awful. My experience was shocking because when I was a kid, Maytag was the ideal for quality and reliability. Those days are over. When delivered in 2013, the ovens did not work. Heating went to 200 degrees and stopped. During the next three years, we had this Maytag stove repaired four times. The most recent repair was in October 2016. A new regulator and igniter cost us $360. Four weeks later you guessed it the ovens stopped working yet again. We sent the Maytag stove to the recycle dump. Its far more valuable as scrap metal.

I bought a Maytag 4452BDW stove, the more button is not working. I did my research and was not happy to see this is a common and reoccurring issue with Maytag Stoves. The expensive of the part that too often fails again along with the cost of the service man to repair it places the Maytag as low quality at a high price. I am hoping to see a company that stands behind its product by addressing this correctly and promptly. It would be a pleasure to have my faith restored as it should be by Maytag.

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

If I could rate it lower than 1 star, I would. We bought ours new in 2005. Within 6 months, the main pulley for spinning the drum fell off not once but thrice. The repair tech said that the shaft was machined incorrectly at the factory and the bolt that would normally hold it on was backing out. The 3rd time it happened was close to the end of the warranty and the tech could not make it out before the warranty date. When he did show up, they wanted to charge us. I wound up putting the part in myself. Two months later, the suds alarm came on, which caused the water valve to open. The pump kicked out and the water valve stayed on flooding my basement and the electronics in the washer. This happened twice. The second time was a week ago and I tossed the ** out to the curb. We also have a Maytag Gemini double stove which does not work either. This is the second and last Maytag appliance that I will ever own. They are junk!

I renovated my kitchen 3 years ago. I decided on purchasing new appliances which included refrigerator, dishwasher, microwave, range, washer and dryer, all of which I got from Maytag. Of course they were always known for dependability but apparently they were not! What happened to this American product? In the last 3 years, I have had my refrigerator (**) serviced 4 times for the same problem. Each time servicing has been a nightmare at the hands of AE service, Preway service and of course at the helm of my nightmare Maytag Customer service. The first mistake I made was purchasing Maytag products followed by the second mistake of purchasing Maytag service contracts. I now have a refrigerator that is not working, waiting on parts since end of august. When I called Maytag customer service, they confirmed the parts were not available and recommended I go online and try to find the part! This added insult to injury. Today, Preway service finally came to install my parts and upon technician’s arrival he opens the part box and realizes he ordered an ice tray cover, when he should have ordered an Interface Control Board. Maytag continues to have their products serviced by incompetent companies and appears to have no interest in keeping you as a customer after you purchase, whatever happen to the dependable people?Maytag had built their reputation on reliable products and dependable service, what happened to this American Made appliance? Here is a prime example of what happened, and why companies like LG and Samsung are gaining more and more customers every day. The best advice I can give someone is avoid Maytag. By the way, I forgot to mention I have 2 small children ages 3 and 4 and Maytag is not concerned about how I would provide food for them with a refrigerator that does not work. Shame! This is not what I expected from what I thought was a reliable company.

Fire Danger. We had a power outage and my Maytag gas range/double oven (Model: MGR6875ADS) was dead after the power came back on. We figured it was the control board and braced for the expense to replace it. A few days later, I plugged the oven back in just to see if it would work and it did! The control panel came back on and we were up and running. The good news end there. On Christmas Eve, we came home to a house full of smoke with fire alarms buzzing. A butcher block style cutting board that was on top of the range with Santas cookies on it was on fire. Twenty more minutes and the house would have been gone.

18 month old range did not shut off although it showed off on the cancel page. $800 down the toilet. Maytag had the guts to charge $100 to troubleshoot plus parts and labor. I will donate it to scrap metal. Company does not give a rats behind. DO NOT BUY MAYTAG.

We bought ALL new Maytag appliances for our home when we rebuilt after it was destroyed by Hurricane Katrina in 2005. We got the top of the line of every appliance. Our Maytag dryer model MDE2706AYW has broke for the 2nd time and cost to repair this time forces me to replace it. The dryer felts, idler pulley and belt went out several weeks ago. Used it about a week and the drum quit turning. The repair tech said the aluminum pulley for the belt on the motor is broke. The pulley is not serviced/available and you have to buy a new motor assembly. This puts repair price on up there where replacing the dryer is the only option. We are going shopping for a new dryer today. It wont be a Maytag.2 years ago, our Maytag washer broke. The repair tech said the transmission went out and it would cost less to replace the washer than to try and repair the Maytag washer. We bought a new washer, different brand. About 3 years ago, we had to have our Maytag dishwasher control panel replaced and 2 months later the pump housing broke. Repair tech said cost more to repair than new. Replaced with different brand.Shortly out of warranty, our Maytag Microwave broke. Everything worked except it would not heat anything. The repair tech said cost more to fix than new. Replaced with different brand. All we have left is the refrigerator which has had 2 expensive repairs done on it and the stove which has had the control board and several heating elements changed. I will never buy another Maytag product.

We have reported the first time use of New Gas Range using the oven and range top at the same time is impossible because of BURN HAZARD AND the response was soft with no explanations. The range arrived March 26, 2015. We were impressed with first baking only. Family arrived at our vacation home for Easter celebration. Our first meal on Good Friday using both oven and range top was a disaster and the cook was burned on the stainless steel knobs. The oven vents below the knobs were about the temperature of the 380 degree setting of the oven!We rendered the unit unusable and called Maytag customer care department during the late table dinner. I explained on the 45 min call we were having this event and would be all leaving Thursday and their solution was 8 to 10 day shipping of Fake composite stainless looking knobs. These knobs will have to be sent to our Ohio home 500 miles west of the Range location?? If they could ship that day why not overnight??THE SOLUTION OF WEARING OVEN MITTS FOR STOVETOP COOKING IS NOTHING SHORT of silly to conduct meals for our guest. And other members of our family that we permit occasional use of the home open to burns using this Range until we drive 1000 miles round trip to drive the knobs back to NJ from Ohio??? Customer Care fails to listen. We will not be returning until May. To illustrate my concerns about the logistical issues I asked if Maytag would pay for the mileage and tolls for me to replace BURN proof knobs. Oh and will it work or melt? Furthermore who will pay for the takeout needed to feed our family? He did not get it and consulted with supervisors for most of the call therefore 45 min of wasted call. No solution, self installation on an $800 Range. Dissatisfied CUSTOMER with an unusable Gas Range Burn HAZARD!! Poor Design oven vents less than 2 inches below stove knobs! See Photos.

I purchased this machine and after 2 loads it started making a very loud and awful noise. Maytag sent a local service person and he found a screw that had come undone and was in the motor. Since then there are a few strange noises that the machine makes during different cycles, usually involving spinning. Called Maytag and then sent repair person. This young man was non-verbal, was probably 20 and it was impossible to communicate and try to figure this out. Person sat through a full cycle and he said the noises are because the machine is out of balance. Well, why did the sync system not balance at the beginning of the cycle. No answer to that. He reported to Maytag that nothing was wrong with the machine.Machine is still making noises and I cannot wash a small load or it will still be wet at the end of the cycle. I am a widow and live alone. I dont wash large loads. So I called Maytag again. They dont care. Finally they agreed to send another 2nd opinion. I have a lot of videos of the machine making strange noises and the repair kid does not care...lots of blank stares from him. I highly suggest not going with Maytag. They dont back up their products and they leave you with a bad machine. My LG FL was perfect. Never an out of balance load. I could wash a single item with no problem. MAYTAG IS A TERRIBLE COMPANY.

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

Great stove for the price. The oven bakes good, the self-cleaning oven is awesome, the top is easy to clean up and regulating the temperature is so easy.

Do not buy this refrigerator!! It’s small on the inside but to top it off the vent is on the left side, not in the back, so everything freezes on the left side of the refrigerator. Plus they positioned the light right in the front at the top so you cannot put a gallon of milk or anything tall. Not orange juice, apple juice, nothing!! Horrible design. I’ve had the repairman out, he said he couldn’t do anything about the freezing on the left side unless he turned the temperature up on the fridge and on the freezer. We tried that & The ice cream was so soft, almost melted. The problem then was the temperature was too warm for milk and other items. Not a recommended temperature to keep cold items. He said I would have to keep everything away from the back & the left side to use it without freezing my items. I’ve lost a lot of food because of this. Very unhappy with this refrigerator!!

Gas double oven - range that has performed well over 12 years old with only one service call for thermostat. Very inexpensive to repair and parts are readily available. Easily cleaned inside and out.

Our product was purchased with our Condo. We have had it for 6 months & the first time I called someone was for the oven door being so terribly hot. I was told that was normal. Then I tried the cleaning of it & you would never know anything had been done. It would take a heck of a lot of elbow grease to get the marks off & I dont have the strength or time to be doing that. I had someone come again & he said to do it again, which I did & it still was not clean. I have done it a 3rd time now & still no better. I think this product is a total piece of junk & would not recommend it to anyone. I am a very unhappy customer & will never purchase another MAYTAG product.

I purchased a new gas range in Nov 2013, but didnt use it until April because I was remodeling a house I had just bought. When I used it to cook Easter dinner, my meal was cold; the oven heats, then shuts off. Maytag has sent service techs 3 times. They have replaced the control board and the DSI module and ordered another part, for which we have been waiting over 3 weeks. Now they tell me it will be here next week. Maytag obviously cannot fix the NEW range, but they refuse to replace it. They deem it to be repairable though they cannot repair it. Customer service claims to be sympathetic, but will do nothing except schedule another service call and offer to extend my service warranty. What good is a service warranty if they cant repair the appliance? If youre smart, youll steer clear of Maytag and Whirlpool appliances. They are total CRAP.

Washer goes off-balance even when clothes are evenly distributed in tub. When it is turned off to rearrange clothes (which may have to be performed a couple of times), washer goes back to starting cycle which means more water. Afraid to do laundry unattended.

I own my oven for 10 years. It still looks brand new. The bottom oven went out and they do not sell the replacement parts anymore. I think its terrible that I had to go and buy a new oven when mine still looks brand new.

I purchased a Maytag electric range model # MER8775AS in Feb 2012. While boiling syrup, the pan overflowed onto the oven door. As I began to clean up the spill I noticed that some of the spill had gotten inside the door on the inside of the oven glass. To remove the stain would require disassembly of the door. I called Maytag and complained of what I called a design flaw and they said, No, its your fault for spills entering the door. They even sent a condescending email to me informing me that if I needed to purchase parts, where I could get them. I designed appliances for years and this is another example of poor quality and lack of consumer service. I AM DONE WITH MAYTAG.

Purchased this maytag oven from home depot November 2011. Oven has been working properly since install. The top burner controls do operate too easy and you can just brush up against the stove and turn the gas on which I seen here was mentioned. My major issue is the stainless steel finish that was applied. It appears that this metal was not properly prepared prior to applying the finish. The oven door is with rust blisters. The metal under the coating is causing this problem. The finish in the other areas is with no problems... No chemicals have been used to clean this oven.Customer service of maytag stated that this stove only has a one year warranty... so if you buy any maytag just remember one year and when it breaks down the cost to fix will be more than a new defective maytag stove. I will not purchase another maytag product and I do not recommend that this manufacturer be considered when purchasing any appliance.

I have always been an advocate for Maytag Appliances. Never bought anything beside Maytag. Our old Maytag refrigerator broke. Would cost too much to fix. So, we decided to buy new. We had the old white, which I was perfectly fine in buying again, however, white was super expensive. So, the salesperson persuaded us to purchase stainless steel. We got a pkg for close to $4000 all in June of 2016. Needless to say, these items have been called for repair within the 1 year warranty over half a dozen times, and have had to replace pieces that have just broken. My worst experience is the stove. I really do not like it at all. I feel the product is misleading. We wanted a self cleaning oven. It is the newest brand out there for what I consider a joke. It is the AquaLift Technology that does not clean anything. My old Maytag self cleaning oven cleaned far better than this. The same spots are in the oven. It just is worthless. I have addressed my frustration with Maytag where I was told that the oven is for the light user. Well, then you need to educate the people who sell your stuff, because I have a family I cook a lot. If this product was made for an apartment single person who does not cook then we should have been informed. Your product states Self Cleaning. Its not self cleaning!!! My frustration went up to the main office of Maytag where their resolution was to give me a discount on a new stove.What do I do with the one I have, and I was told I could sell it!!!! Really Maytag wow from a consumer that has always been a valued customer this is the level of service I get. I ended up purchasing an extended warranty on all Maytag products, because of my fear of something just breaking again. My advice to all is either buy a no named brand or buy something cheaper. Please folks if you have a family do not purchase these products. Its for people that just need a pretty display of appliances!!!

We had a $1700 French Door refrigerator delivered in January, the ice maker worked for 4 days. 4 service calls by 2 different companies and still not making ice. After fighting tooth and nail, we finally got a new fridge.. upon installation the water in the door spewed everywhere and would not shut off, so yet another new fridge was ordered and delivered last Friday. So, after countless hours, missed worked wages and having strangers in and out of our home 7 times, they offered us a lousy $50 prepaid gift card for our trouble. After a little long drawn out fight, they increased it to $130 and said that was their maximum compensation: Shame on you Maytag, that values our time and hourly wage at about $1.00 an hour. NEVER AGAIN!!

I purchased a Whirlpool oven. It is still under warranty at present. I used the self-clean oven feature just before Christmas, it wasnt that dirty but I wanted to have it clean for Christmas. The glass panels on the door had no stain or grease on it, until I used the self-clean feature, and now there is black staining inside the glass. This oven is not even 9 months old, and you cannot clean in between the glass. My second complaint which I believe is a very poor design on Whirlpool’s end is that the steam vents are very sharp. When I went to wipe off the black splash panel just under the vent tube, I cut my baby finger twice!!! And it is impossible not to slice your pinky. I have been working with Whirlpool since this happened, and they finally issued me a new stove. I was to go back to where I purchased this product and pick another stove. So I did this yesterday and checked out all the Whirlpool stoves because the store says I have to purchases a Whirlpool. But every Whirlpool model has the same sharp steam tube vent, and I am presently waiting for the store manager to speak with his higher ups to see if they will let me pick a stove made by a different supplier. I’m actually really shocked to learn that this could end up being a battle especially after I took the manager to every stove in his store made by Whirlpool and showed him each of the vents and just how sharp those vent tubes really are. You would think he would want to be aware of this and deal accordingly. So I post this to warn any potential customers of Whirlpool to check that steam vent on the left side of the stove, and stay away from it as it is very sharp and you can’t help but cut your pinky finger when you wipe across the stove.

If I could give less than one star I would. I purchased a Maytag range in September 2021, 33 days later the oven went out!! I have been fighting trying to get it repaired for months!!! The parts are not in, the parts have been shipped, oops we forgot to ship the parts, the technician is on vacation. You name it, I have heard it. After the phone call today, it looks like I will still be without a range at Christmas!! This is totally unacceptable. I purchased a Maytag because I assumed it was a good brand! Do yourself a favor... Never buy a Maytag or Whirlpool Appliance. Its not worth it. For the range to only work for 32 days is just plain Wrong....

I have a Maytag microwave and stove in my condo kitchen. Both are about 4 years old. Ill never buy another Maytag appliance again. This stove had problems from day 1 and the support was dismal. I had [bought] an extended warranty, which covered nothing (I let it expire and didnt renew). The microwave handle came off in my hand a few months ago. I stuck it back on with gorilla glue. Now it is starting to shut itself off, as if it lost power then mysteriously turn itself back on. Im sure there will be a new microwave in my future and it wont be a Maytag.

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

In July 2001 my husband and I purchased a 6-year old home. We are still here. We have replaced the refrigerator, oven and microwave - all in stainless steel. I am still waiting for the Maytag dishwasher to wear out. It has never been repaired because it has never broken down. Cleans dishes and silverware great.

Almost one year to the date of purchase, my Maytag glass top range stopped working. The oven is still operational, but the range top does not work. The knobs turn and the surface lights go on but the elements no longer heat up. Trying to get a response from a real person at Maytag was impossible. I was put through a myriad of prompts that led me to scheduling a service appointment. I called AppliancesMart and got a wonderful sales person who said a service call would cost me 60 to 80 dollars and that he had not heard of repairs below $300 for this type of problem. Needless to say I am very angry and disappointed that I had not done more research before I purchased this item. If I can prevent one more person from making this same mistake, I will get some modicum of satisfaction out of this horrible experience.

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.

Maytag 6.2 Induction Freestanding Range Model MIR8890AS0 F47 - I am a very careful shopper. I spent many, many hours researching and searching for the best value. It took me over 2 weeks of research to find an induction oven we could afford. We are a family of 3. Normally, we use just one burner for dinner. We bought the range in Feb 2013. On August 5. 2014, we had company over for dinner. I used more than 2 burners and the oven at the same time and the right 2 burners quit working; I now have the dreaded F47 code. I have had numerous Maytag Authorized repairmen out. They ordered every part except for the one that was necessary to fix my stove. I purchased in Feb 2013, burners went out 8/5/14. This is only 18 months old and is JUNK. Arent our landfills full enough?Maytag customer service is awful. I spent hours on the phone, mainly on hold, in efforts to get help. Maytag claims to have such a great 10 year limited warranty but they wont warranty this F47 issue. Thank God I bought insurance with an outside company. The wrong parts that were ordered were at least covered by my own insurance policy; no thanks to Maytag. I am angry that I have to search all over again to try and find the right stove. I am now fearful of induction. I invested in a lot of induction cookware which was an added expense and burden! They need to stand behind their appliances!People cannot afford to waste thousands of dollars every 1.5 years to cook their meals! This has been an extremely unpleasant issue. It has cost me many hours of waiting for repairmen, waiting on hold, getting and storing many wrong parts ordered by repairmen. I calculate this cost me over 50 hours of my life on the F47 problem. Not to mention the time it took me to shop for this junk to begin with!I think they need to recall this issue as it is clearly a design flaw. I researched this and found many other owners had similar problems. The F47 means that the user interface isnt communicating with the range (the circuit board). They placed the circuit board under the burner surface area, sandwiched between the burners and the oven. It was just a matter of too much heat before this board shorted out. The cost to replace this board is over $600. I am afraid of investing another dime into this machine. I wasted time, energy and A LOT of money on this inferior product.

We have a Maytag Gemini Double Oven Range Model MGR6775ADW. This is a gas range and it was purchased in 2006. This past Saturday afternoon after cleaning the dishes, the igniters on the range starting ticking on their own. I checked to make sure the knobs were not on and they werent. The ticking finally stopped after about 2 minutes. After the ticking stopped, we planned on going out for a walk. Fortunately we didnt. In about 10 minutes after the igniters quit ticking, the range burst into flames. Flames were in the top oven and shooting out the vent holes and the holes where the knobs are located. Coal black smoke was also pouring out of the vents. I quickly pulled the stove away from the wall to prevent the cabinets from starting on fire and I pulled the plug to shut off electricity from the stove. The flames subsided shortly after pulling the plug. The kitchen and house smelled of burning wire insulation and plastic. After doing some research on the internet, I found out that many other people have had the same problem. I reported this to Maytag Customer Service and they wanted to send a repair technician to fix it. I told them I didnt want it fixed but wanted it out of my house. I told them I didnt trust the range since some people reported they had it fixed and the fire occurred again. I wouldnt be able to sleep or go out anywhere knowing that the kitchen range could erupt into flames at any time. The factory authorized repair technician, from A&E, did come to inspect the damage and to report back to Maytag on his findings. He admitted that he wouldnt even trust the range in his house. After paying $1300 for this range and only getting 6 yrs. of use, I feel that we deserve some restitution from Maytag on this badly designed and dangerous piece of equipment they have been selling. Do not buy the Maytag Gemini range. This is a bad and dangerous product.

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

Eight years ago we bought all new top-of-the-line, stainless steel refrigerator, double oven range, dishwasher and microwave. All began malfunctioning within the first year: *The refrigerator began to make a loud rattle and the digital control pad needed to be replaced -twice within the first year. Within the next year the compressor had to be replace. *Dishwasher electronic control board was replaced twice, broke again and is still broken. *Microwave door handle broke off, and turntable motor broke.*Range burner ignition system only works on two burners and the shelf for the top oven does not fit -*Maytag refused to replace. Also, after using self-cleaning feature the lower oven still fills the room with smoke so it has been used very little. So, how much worse could it be? I had faith in Maytag-thats why we bought the brand.

We bought a new home with all new Maytag appliances. Our Maytag dishwasher has had 3 new handles, 1 inside tub and now needs a new touch panel. Our Maytag oven/stove has needed three ignitors and the oven door has never been right! The microwave is the only appliance that we have not had a service call. Appliances are expensive along with parts and labor for service calls. I will not be purchasing any more Maytag appliances. The standard comment by repairman: They dont make them like they used to. How sad is that!!