I purchased this oven in April 2015. I have had nothing but problems with the unit. The temperature is off. I have had the probe replaced in July and will be done again next week (January 26, 2016). The AquaLift self-cleaning feature does not work. I ran the self-cleaning feature about 8 times and back to back on several occasions. The service providers stated that it really doesnt work and there is nothing they can do about it. The front of my oven, above the vent, is stained from the oven exhaust. They said there is nothing they can do about that either. The last service company that came out for a service call to check the oven temperature came without the proper tool to check the temperature and ended up snapping the propane line. I was given 6 month of a free extended warranty for my inconvenience and told that the company does not replace models. They will continue to come out and repair them. I will never buy another Maytag appliance again.

We have a Maytag Gemini Double Oven Range Model MGR6775ADW. This is a gas range and it was purchased in 2006. This past Saturday afternoon after cleaning the dishes, the igniters on the range starting ticking on their own. I checked to make sure the knobs were not on and they werent. The ticking finally stopped after about 2 minutes. After the ticking stopped, we planned on going out for a walk. Fortunately we didnt. In about 10 minutes after the igniters quit ticking, the range burst into flames. Flames were in the top oven and shooting out the vent holes and the holes where the knobs are located. Coal black smoke was also pouring out of the vents. I quickly pulled the stove away from the wall to prevent the cabinets from starting on fire and I pulled the plug to shut off electricity from the stove. The flames subsided shortly after pulling the plug. The kitchen and house smelled of burning wire insulation and plastic. After doing some research on the internet, I found out that many other people have had the same problem. I reported this to Maytag Customer Service and they wanted to send a repair technician to fix it. I told them I didnt want it fixed but wanted it out of my house. I told them I didnt trust the range since some people reported they had it fixed and the fire occurred again. I wouldnt be able to sleep or go out anywhere knowing that the kitchen range could erupt into flames at any time. The factory authorized repair technician, from A&E, did come to inspect the damage and to report back to Maytag on his findings. He admitted that he wouldnt even trust the range in his house. After paying $1300 for this range and only getting 6 yrs. of use, I feel that we deserve some restitution from Maytag on this badly designed and dangerous piece of equipment they have been selling. Do not buy the Maytag Gemini range. This is a bad and dangerous product.

I bought a Maytag Gemini double oven gas range 5 burners (model MGT8885XS000), even air true convection cooking. Within 4 months, 1 of the gas valves (knobs to turn gas on with) froze. I could not turn one of the top burners off. Maytag came out and fixed it. Three months later, another one froze. Again Maytag came out and fixed it. Our warranty ended. Over the next year, all five burner valves have frozen. I called Maytag, told them what happened. The most they could do for me was to give me the part half off. So I can pay $200.00 for parts and pay for a repairman to come out and fix it. The oven cost $2,000.00. I am still paying for it. Chances are if I repaired it would break again.

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

I have been on the chatline with Maytag customer service for two days, trying to enforce my warranty, which expires next week. My washer flooded my kitchen over the weekend, and I contacted Maytag to schedule the repair under the warranty. First, the woman, Aisha, looked up my registration, and confirmed that I was who I said I was, that my address and phone number had not changed, and told me that according to the records, the washer was purchased on 2/7/2011. Whats the problem? First, they wanted the model and serial numbers. I realized that this is important information in determining what machine needs what repairs, except there was not one sticker anywhere on my washer! Aisha said that the technician would not perform the repair, if the manufacturer did not install the model information properly on the machine. As if I had any control over the placement, or lack thereof, of proper ID for the washer. This was followed by a request for proof of purchase. I explained that I moved, and misplaced it, but I would have it emailed to me from the original purchaser. I was told that unless she could verify the proof of purchase, and the date of purchase, she could not schedule the repair under the warranty. This is despite the fact that not 5 minutes ago, she had just read this information from her computer! I asked her why would I register someone elses washer under my name and address? She didnt care. I told her I would have the receipt emailed the next day, and she stated that regardless of the date I requested, and scheduled the repair, if the actual repair took place after the expiration date of the warranty, it still would not be covered! I told her that makes no sense. I have no control over your scheduling issues. If you cant honor the warranty if the repair is made after the expiration date, then I need a date prior to that. I am entitled to the terms of the warranty, and intend to use them. Aisha said again that, without proper proof of purchase and purchase date, without proper tags on the washer, and if the repair takes after the expiration date, it would not be covered. I disconnected from her, and reconnected with another rep, who told me that some of the information Aisha gave was incorrect. I can schedule the repair, get the receipt and email it, or submit it through the chat, and regardless of when the repair was actually done, the warranty would still be honored. This person couldnt be sure what effect the lack of proper tags would have on that. My third re-entry into the chat was no better. I located a copy of the receipt in my email, and contacted the chat again. An almost amazing thing happened! This woman again confirmed all of the information Aisha recited last night, and was prepared to schedule the repair, without even asking about proof of purchase. This woman, Jennifer, was willing to schedule the repair, verify that it would be covered under the warranty, even if it was after the expiration date, because I had called and arranged the appointment before the expiration date, and she was willing to have the missing manufacture tags replaced. I had to ask her three times to review the email, and confirm that I had the correct receipt for the technician. I asked if the technician in the course of repairing the washer, had to remove the drainage hose, could he either replace it with a longer one, or add an extension, because according to Lowes at the time of installation, the hose they installed was supplied by the manufacturer, not them. Jennifer stated that since he was only there to repair the leak, and installation is not covered under the warranty, I would have to pay for him to replace the wrong hose, with the correct hose myself, even if he removes it! I told her that she needed to ensure that the technician absolutely did not remove the drainage hose from the back of the washer during his repair, because if he removes a part that is obviously the wrong part, and then replaces the wrong part after his repair, I would file a complaint every single place I possibly could. Why would a repair technician remove a part, determine that it is the wrong part, and then put it back! That is like a mechanic repairing the axle of a car, and discovering the brakes are bad, but since he is only there to repair the axle, he replaces the bad brakes after fixing the axle! He was going to be able to replace the missing manufacturer tags, though! This entire process took at least 3 hours and two days. To date, Maytag/Whirlpool is absolutely the worst company I have had to deal with, right after Sears, and ahead of AT&T. The consequences are that so far, Maytag refuses to have the technician replace the wrong hose with the correct hose, if he removes it in the course of repairing my washer.

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

Our home has seven Maytag appliances: an upstairs kitchen, downstairs suite and laundry room. All were brand new six years ago and what we thought to be good quality by the price we paid for them. We have lived to regret ever dropping a cent into Maytags business account, as we have had nothing but trouble with them. We dont have small kids or teenagers abusing them. Its just us and a very responsible single adult downstairs. And every time we turn around, one of them is costing us nothing but money and grief. Our first problems began with our upstairs fridge when it was only two years old. At that time, it cost us $400 and since then, it just goes on and on. Last week, our downstairs fridge quit, and today, our upstairs one quit. We have had work done on our range, as well as our washing machine and dishwasher. If you are thinking of buying a Maytag appliance, dont, unless you like to throw away your money. I couldnt believe when I looked up Consumer Reviews on Maytag appliances tonight that I would find only 1 out of 5 stars, and read all the terrible reviews written by angry consumers. Well, add me to the list because I will never buy another appliance from Maytag again, and am beginning to think its time to sell this house to get rid of these stupid, useless, pieces of ** Maytag appliances! Sorry, people, but I cant afford to keep replacing them!

Discovered that thousands of others are having problems with the control panel on their dishwasher. Mine is Model # MDB7749SBM2. Looks as if I should just junk this horrible product and buy a new one (another brand, of course). My biggest concern is that I purchased other Maytag products along with this dishwasher, ie, a refrigerator-freezer, a built-in stove top/oven and a microwave. I have had a service call on the fridge (water line), the oven (gas) will indicate a set temperature (400 degrees for example) sometimes it will only be abt 200 degrees via a portable thermometer... Sometimes it doesnt ignite at all (have to reset it 3 or 4 times, the microwave has issues with the digital readouts, and on and on and on.I have only had these appliances about two years (after warranty expired) when each unit started exhibiting problems. I paid $175 for the fridge repair and am now considering biting the bullet & replacing everything as MAYTAG/WHIRLPOOL apparently isnt going to take responsibility for any defect on ANY OF THEIR PRODUCTS! Im 75 years of age, retired and cannot afford the replacement route but it looks like I dont have a choice unless someone has a better suggestion. I dont have the skills or energy to attempt the repairs myself.

Thinking that the Neptune fiasco was over, I happily bought into the sick company and got burnt 3 times for all 3 purchases. The Gemini range with dual ovens: the controller clock with all relays and electronic package is dying, leaving me with no ovens, or slow heating and an alarm in the middle of the night. Now, even the burners are not working properly. Junk at any price, and I paid $2,400. Not 5 years old and repaired several times under warranty; all were electrical failures.The fridge is another failure. Apparently the Freon is leaking out. It is unrepairable and it was typical of these from what the service guy said, not 5 years old. It was repaired once, leaking on floor. Apparently, it was a kinked drain hose. The dishwasher was one year old and it caught fire when the dial was turned while the machine was running. The 4th machine, an over the range microwave, is still running… although from day one it sucks so much power on the dedicated line that it dims the lights in the microwave as it starts up and each time, the magnetron energizes. I am just waiting for it to fail too. Can you say never and mean it? There was no goodwill offered. “So sad” and “too bad” is the common line. Nothing will last more than 5 years if you listen to sales people at Maytag - junk. There was no help from the corporate office. Nothing I can do for you. Junk, junk, junk.

Our Maytag Bravos Top loader with no agitator is headed to the junk pile after 1.5 years of BAD service. I honestly believe that whoever writes a good review on this machine is NOT an actual owner. Lets start with how it NEVER cleaned our clothes... The washer uses barely enough water to get the clothes wet. Soap remains in the clothes so the family is constantly itchy! If you add 3 additional rinse cycles, its still not nearly enough to get out the detergent and youre left asking yourself, What about the HIGH EFFICIENCY???? Next theres the issue of the water never being hot ENOUGH to kill bacteria (were back to the itchy thing). Its suppose to be an energy saver, but at what expense? Its not QUIET like promised (well maybe for the first few months). But upon opening the lid, you realize it was quiet because not a lot was happening to get the clothes clean. Now lets talk about the horrible smell... I dont know where its coming from... It occurs during the wash cycle and smells almost like a natural gas type odor. This is NOT because the washer wasnt cleaned once per month! Maybe its the bright orange RUST near the bleach dispenser or all along the inside rim of the lid... Remember its ONLY 1 and 1/2 years old. Before I get to the ISSUE that finally did this machine in... I have to mention the machines UNEVEN load response.. Brace yourself, it sounds like 1000 tribal drums... and if you dont readjust the 200 lb water logged load, it will just keep on filling up with water and draining indefinitely (so dont leave the house if youre washing jeans, blankets or sheets!). The FINALE of our machine is what I kind of always suspected it would be... the lid lock!!!! One day it stopped in the middle of a cycle and the door remained locked... After unplugging and retrying, the door unlocked, the buttons all worked, but the machine will not fill up with water or start a cycle. To be honest... I am so GRATEFUL! I get to buy a new machine and although Im pretty pissed that the machine died after just 1.5 years, we can finally have CLEAN clothes again, peaceful laundry days and get rid of the ITCHIES!!!! Bye bye FOREVER Maytag!!!!!!

We purchased the Maytag over the range microwave December 2014. Three months after installing it the door cracked. Maytag did replace the door and the repairman thought it might be due to the heat from the stove (huh, it was designed to go over the stove, where there will be heat). Now, six months after that, the layers of plastic on the door are separating and the piece around the control panel is cracked. Maytag agreed to replace the control panel but refuse to replace the door as it is only cosmetic (their words). So much for paying a little extra for what we thought would be a quality product. It seems to me that if something was made to go over the stove, it should be made to withstand the heat.

Almost one year to the date of purchase, my Maytag glass top range stopped working. The oven is still operational, but the range top does not work. The knobs turn and the surface lights go on but the elements no longer heat up. Trying to get a response from a real person at Maytag was impossible. I was put through a myriad of prompts that led me to scheduling a service appointment. I called AppliancesMart and got a wonderful sales person who said a service call would cost me 60 to 80 dollars and that he had not heard of repairs below $300 for this type of problem. Needless to say I am very angry and disappointed that I had not done more research before I purchased this item. If I can prevent one more person from making this same mistake, I will get some modicum of satisfaction out of this horrible experience.

Our Maytag oven (not sure model) in the first year started doing crazy things with the oven computer. The oven would shut off and come back on and the display would be garbled. Also when my girlfriend tried to pull the turkey out, the rack fell off the left side and dumped all the juices into the oven. She almost got burned and there was a lot of smoke. The freakin rack should never fall off! Also our dishwasher is on its second control board. I lived by Mr. Maytag and his airplanes/helicopters at Crest airpark in Covington, WA. I wish I still did. Id like to ask him what he thinks of his crappy products. You get nothing for your money anymore. Im not sure but Ill bet both of my problems with these products have something to do with saving a buck by making this crap in Mexico or some other *** hole. Im just glad Maytag doesnt make airplanes or medical equipment.

We purchased a Maytag electric convection oven with a warming drawer 3 months ago. We have been happy with the cooking features, but not the Aqualift self-cleaning. It does not work and Maytag does not acknowledge this. Instead they have offered cleaning products to us which their own instructions tell you not to use! Does this sound like a self-cleaning oven? They have offered to send out a service person to check the temperature. However, from reading multiple reviews by others, there will likely be no satisfaction from this company.

I own a MAYTAG BRAVOS XL* TOP-LOADING HIGH EFFICIENCY LOW-WATER WASHER. On 9/1/15, after reporting a problem, a service person arrived to assess the problem. His diagnosis led to a second visit on 9/8. On the second visit he replaced multiple parts, assuring us that the problem was fixed. When this proved to be false, we called for a third visit; this time a different person arrived. After disassembling the washer he found a large hole and another cracked area in the inner plastic portion of the tub. We made a fourth appointment for repairs, receiving assurances that it would be repaired at that time. I received an e-mail today (9/16/15) informing me that an additional 7 days would be required to arrange for delivery the required part. In the interim, my wife and I are forced to use a local coin operated laundry about every three days, totaling 7 visits at approximately $25 and 3 hours per visit before the next scheduled appointment. The compensation offered, 9 months extension of the existing warranty is woefully inadequate. I want the appliance replaced, as history has taught me that you are obviously unwilling or incapable of repairing it correctly in a timely manner. Additionally, I want the initial warranty that accompanies a new product extended to a full 3 years. We have paid out over $150 and wasted 18 to 21 hours of our time unnecessarily. I expect compensation for the funds spent as a direct result of the bungling, incompetence of your service staff. My questions are these: 1. Was the part defective prior to installation? 2. If so, why did the representative not notice it and refrain from installing a broken part? 3. Why was there no mention of the damage on the first visit? 4. If not, how did the damage occur? Did the service man damage it and fail to report it? 5. What caused the delay in obtaining the part? I have other questions, but will no longer spend any more time on this debacle. I cannot honestly say which is worse, their quality or their pathetic version of customer service.

I purchased the Maytag oven in January and have had the service technician out 5 times to try to repair the oven because it doesnt heat properly. Theyve told me that because I live in a condominium that it is normal for the oven to take an hour to preheat, then another hour for the second oven to preheat. When I am baking the oven does not hold the temperature and anything I bake takes much longer than it should. They refuse to get me a new oven.

The $1,100 Maytag Bravo XL does not have a dedicated spin cycle. Its rinse and spin. When out of balance, you rearrange and it rinses AGAIN - 15 minutes - before you know whether its balanced. By rinsing again, it can redistribute to be out of balance. Repairmen (w/ extra warranty) said you cant wash bath mats, bedspreads or pillows though it had giant capacity! They would charge me if I called again about it (3 strikes). So bought a used Kenmore with no computer panel... Its great! My dealer had the Maytag hauled to a dump, he would not sell it to anybody as he had integrity.

We bought this stove because of the self cleaning oven feature. What a ripoff! The Aqualift technology simply does not do the job that it is supposed to do. As the lady of the house says, Self cleaning means clean it yourself. Whoever engineered this thing needs to go back to school. Adding insult to injury, we have adjusted the oven temperature to its highest and it still cooks so low that a cake has to be cooked for half as long again than the recipe calls for or the middle of it is still raw. We would like to sell the stove but would hate to burden someone else with this piece of junk.

We bought ALL new Maytag appliances for our home when we rebuilt after it was destroyed by Hurricane Katrina in 2005. We got the top of the line of every appliance. Our Maytag dryer model MDE2706AYW has broke for the 2nd time and cost to repair this time forces me to replace it. The dryer felts, idler pulley and belt went out several weeks ago. Used it about a week and the drum quit turning. The repair tech said the aluminum pulley for the belt on the motor is broke. The pulley is not serviced/available and you have to buy a new motor assembly. This puts repair price on up there where replacing the dryer is the only option. We are going shopping for a new dryer today. It wont be a Maytag.2 years ago, our Maytag washer broke. The repair tech said the transmission went out and it would cost less to replace the washer than to try and repair the Maytag washer. We bought a new washer, different brand. About 3 years ago, we had to have our Maytag dishwasher control panel replaced and 2 months later the pump housing broke. Repair tech said cost more to repair than new. Replaced with different brand.Shortly out of warranty, our Maytag Microwave broke. Everything worked except it would not heat anything. The repair tech said cost more to fix than new. Replaced with different brand. All we have left is the refrigerator which has had 2 expensive repairs done on it and the stove which has had the control board and several heating elements changed. I will never buy another Maytag product.

We have had our Maytag dishwasher for more than two years. Heres how it stacks up: Energy Star rated-Yes; Noise-Almost inaudible except when water runs; Length of Cycles-long except for quick wash 59 minutes; Interior design and loading - 10 out of 10. This is the easiest dishwasher to load and it holds an enormous amount of dishes of all sizes and shapes. Adjustable and removable racks-Yes both. Everything fits including my barbecue and oven racks! Amazing. Stainless interior-Yes including silverware rack. Cleaning- 10 out of 10. Even on a quick wash (59 min) cycle this dishwasher cleans everything! I run a longer cycle just to sanitize if we have sickness in the house. Otherwise it is 59 minutes to finish. Drying-Like most dishwashers this one is only so-so in the drying department, especially on the short cycle. Without plastic containers or utensils the machine dries more completely. However, the amount of moisture remaining after a quick or regular cycle is minimal. The water tends to pool on bottoms of glasses and plastics mostly. Easy to dry by laying a cloth across top rack. Dries in just a few minutes.My only suggestion to Maytag is to work on drying technology to make the machines more efficient and effective. However, that being said, I wouldnt trade this machine for any other. It has every feature I love and a 10-year warranty on parts as well! My machine cost around $600.00. It was neither the top nor the bottom of the line.

Was assured the washer could do comforters, etc. Well, I took a video of the washer doing 5 t-shirt, 1 pair of pants, and 3 pairs of socks on the power wash cycle. Nothing tumbled. All the plate did was swish some water around on the bottom. Clothes werent clean at all. Check my Youtube video, and you can watch the leg of the pair of pants sticking up out of the water and never getting back down in to get wet. Horrible horrible machine. With that said, called the company I bought it from, and they arranged for a front loader since Id only had the machine for a couple hours. Stuck me for a second delivery fee though, which I wasnt happy about. Well see when the new one gets here Tuesday.

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

Replaced an old Glenwood gas stove with this Consumer reports top rated Maytag. The boiler doesn’t work as well as we’d like, but after more than 20 years, no major issues. My wife & I both cook, & as with most things, I’m happier with it than she is.

We bought a Maytag gas range in Feb of 2011. Shortly after that, we started having an intermittent problem with the oven not maintaining the temperature. It sometimes would not heat up to the proper temp or sometimes would get there but not maintain it. We have had several service calls all for this same problem. Each time they would replace things... nothing worked! We called Maytag and they said they wouldnt replace the unit until the same part had failed 3 times. Well, the service company came out 5-6 different times in the first year and replacing the main panel twice and the sensor and some other thingies I dont even remember. Pretty soon the warranty was running out, so I bought an extended warranty due to the fact that the unit had never been fixed. They sent out two different service companies who also were unable to fix the unit. It is now 18 months since we bought it, and Maytag refuses to do anything since it is out of warranty and the extended warranty company will only replace the unit up to 75% of its cost. So yes, we are very angry with Maytag and the way they wont stand behind their product and their total disregard for their customers.

I bought this washer (Maytag HE) almost a year ago, and if I could redo my choice, I would not choose this machine. There is no separate spin cycle. Often items are left with quite a bit of water in at the end of the wash cycle (often literally dripping as you transfer to the dryer), and you cant just rearrange them in the washer and then spin again. The only option on the washer is to both rinse and spin, which almost never helps get out more water. So you then have a heavy load in the dryer, much longer dryer time, and higher utility bills to get some loads dry, especially bath towels, sheets, jeans, etc. The washer is large capacity, but if you fill it more than 1/2 to 2/3 full (depending on the heaviness of your items) the spin cycle definitely will not get nearly enough water out of the clothes. The lid on the washer is SLOPED!The most ridiculous design I have ever seen for a washer, everything you set on top, even for a moment - laundry detergent, folded clothes, wet clothes - ends up on the floor. And the lack of agitator means at the end of the cycle, some loads that contain a sheet or any large flat item (tablecloth, etc.) the rest of the items are captured below the larger flat item that is over them like a mushroom cap. You cant tell how long the items have been like that in the washer, but its hard to imagine they are getting properly cleaned and rinsed. You absolutely cannot use powder stain removers, especially OxiClean, unless you are using the oxi cycle (much longer than regular cycle) because with any other cycle you will have white cloudy patches on all your clothes and items where the powder dissolved in the water but did not rinse out. You have to manually scrub them out, as putting these items through another wash cycle does not remove all the spots.

We bought a new home with all new Maytag appliances. Our Maytag dishwasher has had 3 new handles, 1 inside tub and now needs a new touch panel. Our Maytag oven/stove has needed three ignitors and the oven door has never been right! The microwave is the only appliance that we have not had a service call. Appliances are expensive along with parts and labor for service calls. I will not be purchasing any more Maytag appliances. The standard comment by repairman: They dont make them like they used to. How sad is that!!

I bought a Maytag 4452BDW stove, the more button is not working. I did my research and was not happy to see this is a common and reoccurring issue with Maytag Stoves. The expensive of the part that too often fails again along with the cost of the service man to repair it places the Maytag as low quality at a high price. I am hoping to see a company that stands behind its product by addressing this correctly and promptly. It would be a pleasure to have my faith restored as it should be by Maytag.

I write this as the repairman is fixing my Neptune washer. As with many other complaints, I was experiencing the awful mold smell with the only fix being leaving the washer door open when not in use. This works but for the past few years a switch on the front broke which means we have had to leave the top off the washer and rig it every time we used it. Sometimes it would work and sometimes an error code would show and I would have to just turn to spin and finish that way. At the same time in 2005, I purchased all Maytag appliances. First the microwave went out then the ice maker broke and is still broken, then the dishwasher went out and had to be replaced. Washer broke so basically the only thing that has had no issues is the oven and all happened just outside the five-year warranty. Never again will I buy Maytag.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

I have never had washing machine that caused this many headaches. The point of a machine is to save you time and energy washing by hand. When the cycle is over, the clothes are tightly spun together that we spend half an hour attempting to untie all the clothes that are woven together. The clothes come back to us in knots, or torn because of the rough nature this machine has created. I have never seen anything like this before and would gladly throw this piece of junk out. We are moving and it would create more headaches to deal with this at the moment. I read that the company had severe money problems and it was due to this very issue. I cant believe a company this well known would allow this to ever hit the market! To openly LIE to people and make money off a product that is faulty deserves the karma they get. Please stay away from this company and their rubbish machines they make and then sell. BUYER BEWARE!

Oven worked ok for a year and went under right day after warranty expired. I called factory-approved repair people in Brooklyn but was told repair would cost more than buy new oven. I contacted factory but got no help either.

Major issues with the Aqua Lift Range. Takes forever to preheat the oven, 15-20 minutes to reach 375 f- 400 f. Aqua clean cycle not efficient and does not clean at all. The stove top is impossible to select and keep the heat consistent. When adjusting the heat up or down when you slightly move the dial it overreacts. When moved the heat sways may more than selected. The fridge works well but the bottom drawer is way too flimsy and it wont last a long time as it will crack. This is our first purchase of Maytag appliances and it will be our last. Our old 10-year-old stove worked much better than this one. Sincerely, Russell ** & Linda **, e-mail= **

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

We bought Maytag Gas Double Oven MGT8800FZ only just two years ago and the top part of the range oven has already stopped working. It has not been overused as there are only two of us in the family and we use Crockpot regularly which do not require the range. It was fine for about 23months, but now it will not heat up at all We have been unable to get much help from Maytag so are not at all happy with this product. We chose Maytag as it is a replacement for an older Maytag oven and we have a Maytag fridge which will shortly have to be replaced. Not sure at all if we will replace it with Maytag going on our experience with our double oven.

My husband and I purchased both a Maytag washer MVWX655DW1 and dryer MEDX655DW1 less than 3 years ago from Sears. We had both the washer and dryer professionally installed. Yesterday, we had an authorized service man come in and look at the problems we were having. He told us our Maytag washer would need a new gear case and gears costing $750.Our Dryer, same age, needed a new cycling thermostat. He said it was due to not cleaning out the lint trap. My husband and clean the lint trap after every load religiously. He said there was a pile of lint built up in the dryer. I could only think this would be a design flaw. To repair the dryer it would cost $350. The grand total to repair our Maytag Washer and Dryers would be $1100. We paid $1082.38 at Sears for both. The only thing Maytag offered to cover was a part for the washer which would cost $640 and we would need to pay the extra $110 for service in addition the $150 diagnostic charge, due to use being out of our one year warranty.We decided to not fix this machine to avoid similar problems in the future. I talked to customer service and asked them to cover the diagnostic charge instead of sending the part, which is far more costly. I got the runaround and 3 rejections before they finally agreed to pay for the diagnostic charge. My husband and I are extremely disappointed in this experience. We currently own a Maytag Microwave and Electric Glass Top Range. We will never buy Maytag again. Our Stove is also lacking. We have the AquaLift cleaning stove. The AquaLift technology does not work.

I am writing to tell you the dishwasher sold to my family malfunctioned as a result of an apparent design flaw. I also ended up wasting an entire day for a service person who never arrived. On October 14, 2009, my family bought a Maytag Dishwasher (model #MDBH979AWW) from Home Depot. It had run beautifully until last week, when the left-hand side of the control panel went dead. I then called the Maytag service number (800-688-9900) listed in the instruction manual and scheduled an appointment with the A&E Factory Service vendor for the following Friday (July 6th, 2012) between 8:00AM and 12:00PM. Around 12:30PM, no one had arrived, so I called again. I was told by the agent that the technician was en route and would arrive at my home in forty five minutes. At 2PM, still nobody arrived. I rang again when I was then informed that my name had been strangely kicked out of the system and made available for a reschedule. Wanting to stick with a Maytag-approved business, I went ahead and scheduled the next earliest appointment available, Monday, July 9, 2012. The technician from A&E Factory Service that actually did show up reported that the entire control panel had to be replaced at a cost of $281.48. Interestingly, he added that he had seen other Maytag dishwashers with this exact same problem and recommended that I wait until the water settled before adding extra dishes during a cycle since water apparently leaks into the electronics via a small gap on the top of the inside of the door. Of course, there is nothing in the instructions warning against such.I chose to fix the machine since I didnt have the money to purchase a new one. Are your dishwashers designed to last only a few years? I truly believe that I have been duped by Maytag since this problem resulted from a design flaw. I am asking you to please look into these matters and correct any wrongdoing that you see fit. Copies of receipts for the dishwasher purchase and service repair are enclosed.

I purchased a Maytag Bravos XL Commercial Technology top loading washer, model # MVWB850YWO, in May 2012 and it was delivered in August 2012 due to a home purchase not being consummated. Anyway, I bought this washer and the matching dryer at Lowes and purchased a 4 year extended warranty with Lowes. This would cover me with a warranty through August 2017. I had some problems with the washer while under warranty and had it repaired at least twice. I have had, and still do, have a water leakage in the washer. The water when dispensing into the detergent compartment splashes over and you would think it would just go into the tub. Someway the water leaks down the inside of the washer and runs out onto the floor also causing rust to the inside of the front panel. The resolution was to turn the water pressure down on the supply lines. When this was done, the washer would quit running due to not enough water being dispersed into the drum. A replacement seal was installed and I still have the same problem. The repairmans final resolution was to put tape over half of the detergent dispenser to hold the water in the detergent dispenser and still allow me to put detergent in the dispenser. So, a towel is in front of the washer to soak up any leakage. Now, just 5 months after the extended warranty expired, the bearings under the wash tub are starting to roar during the spin cycle. I contacted Lowes service again and basically I am out of luck. The repair cost is expensive, the part and requires 2-3 hours of labor. I decided to chuck this washer and buy a new one. My wife found one that has an agitator, unfortunately another Maytag, and wants it as she has said the Bravos washer never seemed to get the clothes clean (due to not having an agitator). When checking online for references on a new washer and any recalls on my current washer, I discovered other Bravos XL owners having the same problem with the bearings in the tub. I contacted a local business to try and sell it to him for cheap and when I told him what was wrong with my washer his reply was, I have one just like it out back with the same problem. Dont need two problems. Cant even get rid of a Maytag washer due to it being junk. Many other reviews have listed problems with Maytag products especially since Whirlpool bought them. The Maytags of today are not your parents Maytag. Used to be the Maytag repairman sat around his office waiting for repair calls. This has changed considerably since Maytag sold out to Whirlpool. After doing some research, it seems Whirlpool has bought just about every company selling washers and dryers and are making them as a disposable item. I would advise not purchasing any product that is under the Whirlpool corporate umbrella as I feel whatever they buy, even a superior product like Maytag, they cheapen the product and try to benefit from the name, as in the case with Maytag. So, no more Maytag or Whirlpool products for me until they have proven they can build a quality product once again. Hello GE!!!!

If there was a zero star rating available, that is what I would select! We purchased this range along with a complete kitchen ensemble for a remodel of our kitchen in December of 2011. Within a few months of purchase the enamel finish started blistering, flaking and peeling. Upon contacting Whirlpool Corp about the problem through their online chatline, email, regular mail and phone, we were informed (quite rudely I might add) that Whirlpool does not warranty cosmetic deficiencies over 30 days after product purchase. This is American Quality?? Since this has occurred the retirement home we are building will have no Whirlpool Corp products in it which includes: Maytag, Whirlpool, KitchenAid, Amana, Jenn-Air, Brastemp, Consul, Bauknecht, Gladiator, or any of the product lineup from the Chinese company Hefei Sanyo which they are buying. The attached photos were taken in May of 2012 and since that time the product finish has only exponentially deteriorated.

wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

I have had a Maytag smoothtop stove for over 20 years. The only drawback has been when someone left an empty pan on a hot burner. Some of the pan melted to the top which could not be removed. I have to get special pans to conduct the heat, too. Overall, I love it. It has a self-cleaning oven, too, which is a bonus.

I bought a full kitchen of Maytag appliances when I bought a new house in 2009. I thought it was a reliable company. Id always gone with GE before. I couldnt get the packing sticker off the oven after trying everything to remove it, so the oven bottom is virtually ruined. The timer on the oven dings once and stops; dinner burns if Im not right there to hear it. I was told by customer service thats the way it works, so I had to buy a separate timer. I am now replacing my 2 ½-year-old dishwasher because the control panel has once again stopped working. It cost me $275 to fix the first time and it lasted less than 3 months. I will never buy Maytag again! I got over 20 years of service from my GE appliances.

We had a Whirlpool stove/oven for many years, and it was finally time to trade it in. Everything about that unit was good. While shopping for another Whirlpool, the sales rep told us that Maytag and Whirlpool are one and the same. That we found, is false. An important feature for us in an appliance is the self cleaning oven. The Maytag oven had to be leveled four times after it was installed, in order for the self clean feature to function. The self clean part is only a small indented portion of the bottom of the oven, not the entire oven. And even that does not clean. After going through the dealership service about this problem, I contacted Maytag. My final frustrated summary to the rep was that I understand that we bought a lemon, and you are not going to help us in any way. I just want to say to anyone considering a Maytag stove and oven, raise your standard. If you choose Maytag, you will only be disappointed. I am.

I’ve had this new stove just over a week. Used 3 times (I just moved). I have cooked on staying already on the ceramic top. I’ve had a ceramic top stove for over 20 years with barely a mark in it. Terrible. I’ve left a message with the store with no reply.

From the beginning, the blower motor (for the control panel? never needed one before) was too noisy. I just bought the oven from Lowe’s. They sent out a repairman. He replaced the motor, but has exactly the same level of noise. It is bad design/engineering. Im going to try some other brand. One problem is that you cant listen to the fan noise before you buy the oven and install it. And there are no decibel requirements or ratings. Industry regulations need improvement. Model MEW7527A, bought new in Dec. 2012.

I can see by the comments on this page that the letter I sent to Whirlpool was in vain. I purchased a Maytag double oven gas range (MGT8775XW00) from our local Lowes. We were remodeling a home we had purchased. Unfortunately (as anyone whos been involved in home remodeling/renovation knows well), it took much longer than I thought it would before range could be installed. It was several months later before it was installed. First time I tried to use the top oven, it would heat to set temp (I assume) and then shut down. The larger bottom oven had erratic heating. I tried adjusting oven temps but it was a guessing game. We had Fix-Rite Corp out twice and they were puzzled by the problem. Two times, they replaced the control panel. After the second repair, it was decided the only thing to fix the kitchen was a complete gutting, new cabinets and floor. The oven was pulled out before I had a chance to use it again. By the time we got the kitchen finished and range reinstalled, I discovered the oven still had the same problems and the broiler would ignite sometimes and when it did, the flame would go out after 30 to 60 seconds and would not come back on. By this time, we were past the one-year warranty. After the first repair did not work, I tried to get Lowes to take it back and assured them I would purchase another range from them. They said they could not do that. Now I can see Im going to end up buying another range. Be assured it wont be Maytag and it wont be Lowes. I also own and use Maytag washer and dryer.

Back a couple years ago, Dec. 29, 1983, I purchased a Maytag washer, model A209, and a Maytag Dryer, model DG110. Im still using them daily. The washer has given NO problems, other than the brake has taken to squealing. This causes nothing more than a notice that the load is done, so no repair is necessary. The dryer has proven more problematic, as I have had to replace the ignitor three times, the blower fan twice, and the motor (and belt) once. I still think I have gotten my moneys worth.

I purchased a Maytag Dishwasher (MDB7749AWW1) just over a year ago from Sears. I did not get an extended warranty since the appliance wasnt over $1,000 and I thought I would take my chances. Sure enough, about one month after the warranty expired, it all falls apart. There is something wrong with the control panel and I cant get anything to work. Ive been looking online and see that this is a common problem. So rather than throw more dough into the money pit, Im purchasing a new, simple, uncomplicated GE Americana washer from Home Depot for $279. I figure this will cost me less than going through the repair dance with Sears and Maytag. I will never purchase an appliance from Sears again. Ive been through the mill already with a $2,000 Jenn-Air range that has broken down five times in the past three years (2 times it was the control panel). I was lucky that I purchased the 5 year extended warranty on that one, but never, ever again will I deal with Sears.

I read some of the reviews on the Maytag ovens. I too have the same problems! Have had control panel replaced and still have to set at 400 if I need to bake at 350. It also takes forever to preheat. Trust this review because I am one very unhappy consumer!! DO NOT buy Maytag!!

Fire Hazard - poorly designed with vent at bottom of oven, Warped Drawer and Melted cabinet surface. Nowhere in the install instructions does it say not to mount above drawers. Whirlpool tried to blame dealer. Buyer beware.

We purchased our home five years ago. We bought a new Maytag oven and fridge/freezer. Within one year, the oven control went out. Then a few months later, the heating element went out. Within two years, our fridge/freezer went out. I purchased Maytag products because of the commercial where the Maytag repairman is doing nothing. I will never purchase a Maytag product again.

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

We bought this range (model MER8700DS 1) March 25, 2015. Manual states when you use the oven first few times odor or smoke may happen and is normal. It also tells you this is not harmful but remove birds to another room because the fumes can kill them. Noxious fumes? Forget about the birds! Had to open up the whole house and go outside. Burned my eyes, throat and lungs. Day after day, repeatedly turned temp up to 400 trying to burn off what we thought might be a coating. No luck.Maytag got very concerned when I explained about the noxious fumes and had someone come out right away. Tech took it apart. He removed bottom (screwed in) plate that covers the bottom heating element. That plate gives the added ability to have 3 racks and make full use of the 6.3 cubic ft. capacity. Under the plate we found bits of insulation. We think that is what we smelt as it burnt up. He couldnt smell anything when he had it up to 400. So off he went thinking problem solved. Well, it still stinks. We will have Home Depot take it back. Oven takes forever to come to temp which we read in many complaints but thought thats minor. Dont know what oven to get instead since Whirlpool makes so many brand names. And other brands all seem to have their own problems.

I take pride in my cooking and love my kitchen. As you know this is where everyone gathers when you are entertaining. The Aqualift system does not work. I have run the process 3 to 4 times consecutively in row and the inside oven the oven is never clean. I wipe out the sides over and over. So disappointed. The only saving feature is that you can not see into the horrible look of the inside the oven when it is closed. Was this feature really tested before it went to market????

I purchased a Maytag electric range model # MER8775AS in Feb 2012. While boiling syrup, the pan overflowed onto the oven door. As I began to clean up the spill I noticed that some of the spill had gotten inside the door on the inside of the oven glass. To remove the stain would require disassembly of the door. I called Maytag and complained of what I called a design flaw and they said, No, its your fault for spills entering the door. They even sent a condescending email to me informing me that if I needed to purchase parts, where I could get them. I designed appliances for years and this is another example of poor quality and lack of consumer service. I AM DONE WITH MAYTAG.

Bought a new Maytag Over the stove model Microwave from Lowes. It worked fine for a while. Then it started saying open close door. We opened the door and closed it, and sometimes it would work. This went on for a while till it finally would not work at all. Called for repair, the service guy came and took it apart and one of the door switches needed adjusting. He left and it was working, good deal. 2 days later open close door started all over again. We found if we lifted the door when closing it, then it would work sometimes, until one day it would no longer work. We called for another appointment, and got a new company to fix it called ABCO. The service guy showed up and tightened a screw and it worked again, said the other service guy might have forgot to tighten it down. I tried it and it worked. We did not touch it again till next morning and back to open close door again. Called ABCO back and got a new service time for Wednesday next week. Wednesday came and went, called to see why no show. They said we were not on the service list and were very sorry. So we set up a new time for them to show the following week Tuesday between 12 and 3 pm. At 3:49 they called and said sorry, but they were not going to be able to make it today. I told her then get us tomorrow and was told they were very busy and maybe Thursday would be better. I told her we were in line and and should get service before others that came on later. Her reply was maybe Monday of next week was better. After the runaround she said they would try for Wednesday tomorrow, but no promise made. After that I called Maytag direct and they said nothing they could do except make another service appointment. She told me I could get a service appointment tomorrow Wednesday between 8 and 12am or 12 and 3pm. I asked with who this time and was told ABCO who just told me they were too busy to show up tomorrow and had put me on standby. In the meantime I paid over $300 for the Maytag microwave that is never going to need service because the Maytag service man is so lonely. And bought a $ 200 Panasonic counter model so we could have a working microwave. So now we are in over $500 and still no Maytag working microwave. They did send me a letter offering me a discount on extended service plan if I want one. I told them it would be cheaper after the one year runs out under warranty, to just junk the microwave because it has cost me way more in wasted time, waiting for the lonely Maytag repairman to show up. Bottom line do not buy a Maytag Microwave model MMV4205DS-1 unless you just want a good looking decoration over your stove with a nice light, and have plenty of time waiting for the lonely Maytag repairman.

I purchased a Maytag Neptune 24” front load washer (MAH2400a) and 24” electric dryer (MDE2400AYW) on October 26, 2005 from Sears in Chesterfield, MO. In April 2011, the drum in the washer began to slush and grind. Water also began pooling around the machine. I called Sears and arranged for service repairman. Before he even looked inside the washer, the repairman wanted to give me a coupon for $50.00 off a new washing machine from Sears. After my insistence, he finally opened the washer and told me I needed a new drum. Because of the Sears repairman’s reluctance to look at the machine, I had another appliance repairman review it and was told that the water pumps for this model were defective. Any loose items the size of coins collected inside the pump and damaged it. I paid $340.00 to get the pump replaced. Ten months later, the dryer started smoking. After scheduling a service call, I was told the heating element burnt out and it would cost $360.00 to replace. It was then I noticed that the washer was leaking again. I took the front base cover off and saw mold growing under the machine. A little research uncovered that this set of machines has had many dangerous problems, from mold to catching on fire. There was a class action lawsuit filed and won by consumers in April 2005, yet I was sold this model in October 2005. I feel both Maytag and Sears knowingly sold me a defective and dangerous product. I would like to be refunded for this set.

I bought a Maytag range (MET-8775) last year, because my wife loves to bake and wanted the double oven. The oven never did brown properly, despite trying different temperatures and cookware. So, I called the 1-800 number in the manual. I was told they would have a technician come out and check it, and they assured me it was under warranty. The technician arrived, and since it was close to the end of the warranty period, I showed him the receipt for purchase. I got another assurance that this visit was covered by the warranty, before anything was actually done. Well, he checked it out and eventually calibrated the temperature. That helped a little, but still, it doesnt brown very well. About a month later, I got an invoice from the service company that dispatched the tech telling me Maytag will not cover the visit under warranty. After a long call with Maytag (now Whirlpool, I believe), I was told that since the calibration instructions were in the manual, it wasnt covered! Well, why wasnt the thing calibrated to begin with? And your average customer is expected to have an accurate thermometer/gauge to set it and know whether the temp is off or not? Why was I told twice that it would be covered? If either the lady on the 1-800 line or the tech who came had told me this wasnt covered, I would have argued a case right then. As it turned out, I had no choice but to get billed for something I was assured was covered. And as I said, it still doesnt brown right; and we had tried different temperatures before. We are preparing a major kitchen remodel, and its hard to believe that Maytag/Whirlpool would so thoroughly piss off a customer and potential future customer over an $80.00 service call.

I purchased a range 5 months ago. It is STAINLESS STEEL. It began to rust. I called customer service and they told me it was cosmetic, so they wont help. I think a stainless steel range should not rust after 5 months. Very disappointed, WILL NEVER BUY MAYTAG Again.

I bought this MMV4205BAB microwave thinking Maytag was a good brand and I wanted an over the range type. Problems began when it would stop in the middle of a cooking cycle. I called the repairman as it was under warranty. It was decided by the repairman that the weight of thing was too great for its thin frame, not letting the door close correctly. I got a new one and it, from day one, would make a shorting sound every time anything was cooked, on the stove top, under it, while it was on. It finally just shorted out. I have a Maytag washer and dryer that are also junk. So, needless to say, Maytag, 3 strikes and youre out. I will never have another Maytag product and I let others know what a great product it is.

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

Purchased top of the line Gemini oven a few years ago. Lower oven stopped working. Maytag repair said igniter not installed properly at factory. I contact Maytag customer service to see if they would help with repair cost. Rude response from them... basically saying anything fails after 12 months not our fault. Rejected my request without even asking details about product which model etc. Unilateral rejection. Horrible customer service. I will never purchase Maytag appliance again. Horrible, horrible, horrible. Avoid this company and their products. They do not a good product and they provide terrible customer service.

Purchased my Maytag range/oven 14 years ago and it still works to this day. I had to replace both oven heating elements. I am a do it yourselfer, took me less than 5min to replace both. The cook top is easy to clean. As long as you take care of it, it should last you a long time.

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

I am very pleased with the product, a perfect stove for cooking! It’s very easy to operate, easy to clean, multiple burners, excellent in cooking large meals, like soup, beef, Chicken and vegetable soup. It’s also very energy efficient, very safe to operate,

I purchased a Maytag Gemini gas range in July 2006. Rust has appeared on the bottom of both oven doors. I called Maytag customer service, realizing that my range was no longer covered by warranty. However, I feel the paint on a range, costing over $1,000, should last longer than 5 years. Customer service told me to call a repair technician. When I asked who would pay for this service call, they didnt even bother to respond to me. As I have read other reviews of dissatisfied Maytag Range owners, Im glad I didnt waste money calling a repair tech who would do nothing to help, but charge a $100 plus fee. The paint on a car, which is subjected to all kinds of weather, lasts much longer than 5 years. You would think the paint on an appliance inside a home should last much longer. This rust is becoming very unsightly. I will certainly not purchase a Maytag product again, as the company has proved they do not stand behind their product line.

This is my first convection oven. It is a double oven and I am hooked for life. I love the smooth top and use the convection daily. The only small issue I have is that the touch buttons on the range are on the harder side to push. But other than that, I have owned this for 5 years or more and would only get the same type again if I had too.

Peeling of paint off the oven finish, inconsistent heating, fan goes on and cant shut off until the oven cools, have to leave door open in order to shut fan off. The paint peeling is really bad. It is right where the heat escapes from the oven, have to touch up paint every so often so it doesnt look so bad and the discoloration is covered besides the peeling.

My Maytag Bravos washer is 3 years and 7 months old. While not in use the lid lock motor shorted and caused the control board to fail. No lights on the control panel. Without an extended warranty I called a repairman and the above diagnoses was the result. The estimated cost of repair was $600.00 plus, this includes the lid lock switch and the control board. Might as well buy a new washer instead of paying that much. I called Maytag and complained. The first person I talked to offered me a one year warranty plus the repair of my machine for $345.55 which was less than the repair estimate, sounded good. They set me up with an appliance repair in the area and I said ok. Next I checked the appliance repair on the BBB site and didnt like what I saw, so I called Maytag and told them to cancel the appointment and they suggested I try another appliance repair. I was told I had to talk the warranty company to arrange for a new repair facility. I talked to the warranty company and they agreed to change repairers and I choose the one that gave me the diagnoses. While we talked I told them that the repairman I choose was here and gave me the diagnoses that I was complaining about. The warranty company said they could not warrant a washer that had been looked at and diagnosed. They canceled my warranty and said they would refund my money.The only thing left to do is buy a new washer. Not a Maytag this time. For those of you who are in the market for a new washer and dryer (had trouble here also) I would advise you to read the complaints and I believe the majority of them. Not too long ago there were full page ad in our Sunday paper touting the merits of owning a Maytag product. One thing you cant do is advertise quality when it is not in the product.

I purchased high end Maytag washer, dryer, dishwasher and microwave in May 2010. On Saturday 4/25/14, the Maytag Microwave stopped heating. The fan runs, the panel, display, lights, clock, and tray all work. It just doesnt cook. The Microwave was installed in June of 2010. Not even 4 years old. I have tried to troubleshoot via the instructions that came with the microwave, i.e. Check the demo mode is not on. Dont know why after 3 yrs it would be, but checked it. No help. Pulled the plug out and replaced; turned breaker on and off; checked to see if its was locked. Nothing. I then checked the door and I found that the plastic inside panel on the latching side of the door is pulling away from the door itself, which is part of the locking system. The magnetron shouldnt work if the door system isnt closing properly. The latch system is what is causing the door to pull apart. I am wondering now how much microwave exposure my family has been getting from a malfunctioning door? I have had a Microwave, dishwasher and refrigerator made by Maytag in the past. The refrigerator is 14 yrs old and still works fine. The microwave and dishwasher were at least 10 yrs old when I replaced them with the new Maytags I have now. Here is the problem. Maytag is not Maytag Corp. anymore. Whirlpool Corp now owns the Maytag brand. Prior to the old Maytags I had, I had GE fridge which was junk, and Whirlpool, dishwasher, stove and microwave. They were also junk. I swore I would never buy Whirlpool products again. Surprise.

Should have read reviews. Ill never buy another Maytag. This stove has been bad almost from start. Stove has burned marks from using broil. Repairman told me not to use broil anymore. One of eyes has been worked on 2 times; the knob does not work correctly; when you turn off, it goes past the off and keeps on going to the left. It is very hard to clean surface. I have had a few years. Company paid for one repair. They should have replaced stove from beginning. Not safe.

We had remodeled our kitchen in 2009. Bought new fridge and stove (Maytag). The oven door came off and cant get it back on. No matter how many times we tried, no way can we get it back on. I had to have my son to come and help us. No sooner did we use the handle to open the door off again. This has been going on for 3 years. **, well fed up. I called Maytag about this issue and they told me they would get a repair at my cost. The fridge freezes all the produce, cant regulate the temperature. Never ever will we buy any Maytag product again. Who knows what’s going to happen next? Oh, and the paint is chipping off of the grates of the gas stove.

Paint bubbling & peeling off appliance: I purchased new double convection oven from Lows (Maytag). One month after delivery, paint began to bubble and peel off. Maytag takes the position that as long as the oven functions properly, the paint is simply cosmetic and the warranty does not cover cosmetic problems. Maytags position is that even if all the paint peels off but the appliance still functions properly, too bad for you!

We bought a new Maytag electric range from a local dealer three years ago. The oven element quit working, which shorted out the motherboard that controls the entire range. The cost of repair was $500 for the element, motherboard and installation. We have owned other brands that lasted 20 years and worked fine with no repairs. My folks have used Maytag for over 50 years with no problems. Who and where is this junk manufactured now? China? I will never buy another Maytag product!

We purchased our Maytag gas range in 2015. Within 6 months we noticed the clear coat and paint was defective, we called Sears, they allowed us another range top and replaced it but told us our warranty was up in a month and they would not replace another. The stove always looks dirty because the clear coat and paint have bubbled up and it is clearly a 100% manufacturing defect that should be recalled.

We inherited this Maytag (Model MGR7662WW) when we bought our house this year. I love this unit. It cooks accurately, its easy to clean and its just rock solid in its performance. I never worry that the cook times are going to be off either. The oven racks are solid and the overall look is nice. Our friends and family love the center grill as much as we do. If I need to pull something off the burner I dont worry that Ill scratch the stove top with this feature. The oven heat is also pretty contained. Our old oven radiated lots of heat through the top. This one doesnt and thats a huge plus. The only reason Im not giving it 5 stars is that the grills are cracking (not the center one). However, I have no way of knowing if the original buyer damaged them or if its a defect in materials. They still work fine but I will need to replace them at some point. Given the cost of replacing them Ill wait as long as I can.

I purchased a Maytag over the range microwave a couple of years ago when I had my kitchen remodeled. I have had it repaired twice already. Each time, it cost over $150. I bought this product with confidence that it was a quality product. To say the least, I am very disappointed and I will never buy this brand again. My previous microwave lasted over 15 years without a single problem. The only reason that I got rid of it was to have matching appliances. It was not a Maytag. I am looking to buy a new microwave and I will be sure to look at the reviews to prevent being suckered again!

The AquaLift Self-Cleaning is a very poor substitute for a normal high temperature Oven-Range. It gives as much work as an oven without any self-cleaning, as it does nothing to the sidewalls or the door. The minimum temperature is 170 Fahrenheit, too high to rise a dough.

I have always been an advocate for Maytag Appliances. Never bought anything beside Maytag. Our old Maytag refrigerator broke. Would cost too much to fix. So, we decided to buy new. We had the old white, which I was perfectly fine in buying again, however, white was super expensive. So, the salesperson persuaded us to purchase stainless steel. We got a pkg for close to $4000 all in June of 2016. Needless to say, these items have been called for repair within the 1 year warranty over half a dozen times, and have had to replace pieces that have just broken. My worst experience is the stove. I really do not like it at all. I feel the product is misleading. We wanted a self cleaning oven. It is the newest brand out there for what I consider a joke. It is the AquaLift Technology that does not clean anything. My old Maytag self cleaning oven cleaned far better than this. The same spots are in the oven. It just is worthless. I have addressed my frustration with Maytag where I was told that the oven is for the light user. Well, then you need to educate the people who sell your stuff, because I have a family I cook a lot. If this product was made for an apartment single person who does not cook then we should have been informed. Your product states Self Cleaning. Its not self cleaning!!! My frustration went up to the main office of Maytag where their resolution was to give me a discount on a new stove.What do I do with the one I have, and I was told I could sell it!!!! Really Maytag wow from a consumer that has always been a valued customer this is the level of service I get. I ended up purchasing an extended warranty on all Maytag products, because of my fear of something just breaking again. My advice to all is either buy a no named brand or buy something cheaper. Please folks if you have a family do not purchase these products. Its for people that just need a pretty display of appliances!!!

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

Received this Maytag dishwasher model MDW7749SBW1 as a gift from my son in June 2013 when my old dishwasher finally quit. January 2014, the soap/rinse aid dispenser did not work. Called Maytag and they sent repairman who replaced the part. Still did not work so repairman said another part was not communicating with the dispenser so he replaced that part. Worked fine. No charge since it was under warranty. Now its July 2014 and the touch panel doesnt work. Called for repair and was told since it is out of warranty, it will cost about $350 to repair. I called Maytag about this and said that I had a defective appliance. I was told that since I didnt buy the extended warranty, there was nothing they could do. I mentioned my last Maytag lasted 25 years and had only two minor repairs so I didnt see any reason to buy an extended warranty. I thought I was buying a good product. I was told shed register my complaint. Waiting for my repairman to come out tomorrow and see what he can do. I also have a Maytag stove. Wonder how long that will last?

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

I had a stove my mom bought for me 26 years ago. Still worked perfect. Used constantly. In 2018 my husband had to have this stove. Said no my stove my mom bought and still works perfect sentimental plus three children using it. Not one problem. So he buys this Maytag stove I didn’t like but don’t cook much warming things up or frozen pizza. Go to our sons for holidays. Always next day cook a turkey for sandwiches. Open the door which is too heavy. Wouldn’t close and called my husband. Got it semi closed. Said we’re not eating it. He proceeds to cook. Door opened. More turkey is in garbage. My husband started reading. I also did. Looks like these Maytag stoves are garbage. Make a lot of money for repairs. Now this goes to dump. No one stands behind their products. Is it worth paying to repair no.

I have never liked the stove because it is too small (it came with the triplex) and it has porcelain like top. One burner burns to hot, the other three mediocre, there isnt enough space between the burners and the back of the stove. It doesnt cook evenly and it really does not have a low or simmering setting. You cant set a timer for simmering because it cooks too fast. The knobs are stuck and sometimes wont light when you turn them down. The oven is okay, but could be better. Wish it had self cleaning. The broiler in no existence. Food way too close to the flames. We have had this oven since we bought the triplex back in 2011.

Maytag washer, dryer, oven, microwave over-the-range - all crapped out in four years. I will never buy or recommend Maytag. I believed them to be one of the best brands but apparently theyve learned a few too many shortcuts.

Model MMV4205FZ3 microwave hood combination. No problems with open door signal yet. However, light over the stove burnt out. When removing, it exploded.No didnt unplug first. Previous microwave didnt have a problem with this. Instructions are useless. Didnt say to unplug and doesnt provide a model number for the bulb. Consequently, we have now purchased 5 different bulbs and they dont work. Tested socket and power is going to it. Rep at Ace Hardware said he had heard about this happening several times and provided what was to be the correct bulb -- didnt work.

Maytag Bravo XL - We bought the set about a year ago, after high recommendations from the salesman at Best Buy. This washer does not clean clothes - they come out with soap & spots & white stuff, even after I use the deep water or the extra rinse cycles. These cycles take well over an hour. When they are finally finished, my clothes are twisted into ropes that have to be unwound & taken apart before putting in the dryer. I hate to think what its doing to more delicate clothing, getting stretched & tied up like that. This washer is awful - cant wait to get a new one. The dryer isnt much better - cant believe a $900 dryer doesnt have a steam refresh cycle! And the controls are so touchy - if you actually push them, they dont work. If you lightly hover over the button & barely breathe on it, it does - very strange.

We bought a Maytag oven in Late October 2018. On January 22, 2019 the oven quit heating. Since it was still under warranty we called Maytag and they sent out a contracted service technician. The service tech said the circuit board had gone bad, and said it would be 5 to 10 days for part to come in. After a month the part still had not come and service tech was not returning calls. We called Maytag after another week and they provided very little help other than, We will contact service tech. Service tech never called us nor did Maytag call back. Called Maytag back on 3.10.2019 and asked how we could get this part and oven fixed. Customer service representative was not very helpful as they asked for part number which she was told was a circuit board and the tech they sent did not give that to us. After the customer service rep continued to provide any help other than say call service tech they sent out. I asked what if they replaced it for us since we have been without now for almost as long as we have owned. She stated Maytag does not do this except in extreme cases. I asked what is considered extreme cases. She stated she did not know. At this point I asked if she could transfer me to her supervisor and sat on hold for an hour, then had to leave for work. Very disappointed with Maytag and their lack of support to back their product.

Purchased a Maytag Electric range Model MER8800FZ2 in 2019. The surface Scratched the first week of purchase and the stains will not come off. When I called customer service they claim they are not responsible for cosmetics. In my opinion, This model was put together with the cheapest material they could find. Maytag is not what it used to be. The Elements take a long time to heat up. Inside the oven, the Glazed Paint is cheap product also where once it stains with food it never comes off.

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.

Maytag gas range 5 burners. Maytag is quality. Period. I doubt that other brands are made as well. From the handle of the oven door to the ease of cleaning the burners, you wont find better for the price. I look for quality and reliability. I read reviews. A deal breaker on any major purchased would be too many bad reviews and shoddy materials or construction. This range has 3 regular burners, one large burner and one small burner. The oven shelves easily adjust from one level to another. The controls are easy to reach and the timer and bake controls are easy to operate.

Like many people here, I have a Maytag Dishwasher Model # MDB7749SBW3 Serial # F40107007. We have had this dishwasher for about 12 months to 18 months. The first indication that there was a problem was some of the lights were acting strange. Then the dishwasher starting going nuts. I removed power from the unit thinking that maybe the controller became confused. The problem persisted. I would hit buttons and either nothing would happen or something completely different would happen.I take the dishwasher door apart and remove the touch pad. I notice some discoloration on the ribbon cable. I remove the glued on front panel to look at the electronics behind it (see pictures) and I see some discoloration there as well. So using my multimeter, I find that there is a direct short between pins 4 and 5. I vigorously flex the cable at the point of discoloration and the short goes away. So at this point, I doubt that I can get just the flexible circuit strip so Im going to have to pop for a new touch pad assembly. I didnt go further in the measurements as there was no point since I already detected one failure. Furthermore, I inspected the computer control unit and I did not see any obvious signs of corrosion or discoloration anywhere on the processor board. So it appears that there is no problem with it.Conclusion: Many people are at a disadvantage when it comes to electronic devices. In my professional opinion, this is clearly a failure of the insulating material of the ribbon cable due to environmental contamination. Visual inspection shows that corrosion of the conductors is clearly evident. About Me: I have been an electronics technician on and off for over 20 years now. I have a 2-year college degree in electronics technology and I am currently in school to become an electrical engineer. In my house, when something breaks, I fix it.

Absolutely the worst experience ever. The repair people that were sent to address the problem were great but the Maytag people did not care. I bought a new electric convection oven, the convection never worked. The repair people came out several times and checked and adjusted to try to fix the issues but the oven is totally inconsistent. Even the repair people thought I should have gotten a better response from Maytag! Maytag just said that I had a repair but not replace warranty - of course the warranty period is over now. I had trouble from the beginning, I would never buy another Maytag product. I thought that a company that supposedly has a great reputation would care more about their customer.

Maytag wall oven Model# MEW7530AB01 - We ordered this oven from Home Depot on Aug. 28/13. It was delivered on Sept.7/13. After a self clean cycle, the oven failed on Sept. 24/13. It was repaired on Oct. 23/13. Parts come from U.S. Im in Canada. Part # W10545255. It hadnt cleaned completely so I used the self clean mode again on Oct. 24/13. Oven failed. Fixed again on Nov. 15/13. Same part. Tested self clean again. Oven failed. Repairman fixed a different part. Thermostat #4449751. Oven still not working, had to order the front fuse again. Part # W10545255. Fixed Nov.19/13. Failed again Nov. 19/13. After not having a working oven for so long, Maytag finally agreed to send a new one. It arrived Dec.5/13. Tried cleaning cycle just to make sure. Oven failed. Same part. Called Maytag, told them I just wanted my money back. They refused. They would only repair. I agreed to have a repairman from another company come out. I told Maytag what part it was. They sent the repairman out on Dec. 19/13 with the wrong part. I called Home Depot a second time. I had called them after I talked to Maytag. This time Home Depot said they would take back the oven once it was repaired and I could have a store credit towards another brand. The repairman fixed the oven on Jan.9/14. Home Depot picked up the oven and replaced it with a GE and I love it.The part failing is a fuse in the top of the oven right at the front. Both repairman noted that a lot of heat is in this area during a self clean. When two ovens are having the same problem, I come to the conclusion that it is a design flaw and should be recalled. I only talked to one person at Maytag who was polite on the phone. That was the woman that got me the new oven. Everyone else was rude and hostile. I was even asked why I would clean a new oven. My experience was not a pleasant one at all. I wont be buying any products made buy the Whirlpool Corp. again.

Ive had my Maytag (above range model) for about 4 months. The same as everyone else with open/close door error. Faulty door switch. When the interior light doesnt come on, I know I will get the error. You would think Maytag would have already repaired or replaced this door switch part.

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

Maytag Gemini - This is a double oven which I purchased in 2010. 2 days ago Apr 13, 2015, the outside glass in the bottom oven simply exploded. The oven was in use at the time. It blew the side brackets off and glass was spread into my dining room as well as a mess in the kitchen. Maytag was supposed to send repairman today. Have waited all day and finally called repair company. They knew nothing of the repair and supposedly will contact Maytag and call me tomorrow. We will see. In the meantime has anyone else had this problem?

Purchased this oven at Lowes on 2/8/2018 for $1925. Worked good until my wife cleaned the lower oven on 11/22/2019. The next morning the oven was locked and nothing would work. We called for service and the repair bill was $194.55. I told the repairman that the oven had a 10 year warranty on it, one year on everything and the rest on the parts only. He said no, and showed me in the warranty book that it only covered two parts. Which was not the two parts he had to replace. If you purchase a oven with self-clean feature, I would recommend that you do not use it.

Our oven is 3 years old and the last time I used the self clean option caused the control panel to malfunction. Now we have to buy a new panel. The repair guy online advises people not to use the self clean as this is a common problem!!! What? I cant use that feature? That is so ridiculous!!! Now we have to pay $300. Whatever happened to the Maytag claim to quality and you would never see a Maytag repair man? Something needs to be done about the problem of appliances and electronics being so poorly made and basically disposable.

I purchased a Maytag Gemini April 22 2017 and I am very unhappy with it. The ovens are not working properly. I have thrown away so much food because the ovens won’t hold temperature. The display says it’s the temp. I set it but the temp keeps dropping and rising causing the bottom and top to burn and inside not to cook. Both ovens are doing it. Had a repairman come day before Christmas. He said there is nothing wrong. He said set temp, when preheat beep goes off wait 15 minutes for it to cycle then insert food. I tried this Christmas Day. Oven is still not working and again I threw away more food. I am so disappointed in Maytag. Serviceman is set up again to come out next week. I think I got a lemon. Please. I think they should replace the whole range. It’s not fair. I paid so much for this range and can’t use it.

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.