Purchased my microwave in 2005 and seldom used it. However in the last few months, the halogen light which lights up the range surface has been flickering. When I asked an electrician doing other work around my house to repair it, he discovered that the halogen light is attached with a dual pin socket which is plastic. When the halogen light gets overheated (and halogen produces alight of heat) it melts the plastic. It has already melted some of the plastic socket. When it fails to operate, I will have to repair the light socket which will be very expensive or buy a new microwave. This microwave cost $800 or more because it offered convection cooking which I have seldom used.This is what is presumed quality appliance? Plus I added the cost of an extended warranty.

We had a wonderful Bisque Maytag double oven in 2002. We bought new stainless appliances this year, and have been very disappointed with the range. Why do you have to hold the temp and timer settings one increment at a time to set it, and why do you have to push Start after that? Frequently we set the temp or timer and walk away, only to find that the oven or timer did not begin because we forgot the new step. When the timer goes off, you have to push it twice to get it to reset. The burners themselves have too many confusing pictures for the settings. What happened to low heat, medium and high and hash marks in between? The stove top itself is a nightmare to keep clean. Give me back my coil stove any day!!!

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

Does not wash. Only very small loads get washed even though it claims to wash bedding. Some clothes NEVER get wet. Many times the clothes have to be rearranged and re-washed AND extra rinse. Cycles are over an hour each (then multiply x2!!). Maytag service has been called MULTIPLE times. They replaced the touch pad then the computer board. Both times saying the machine works “according to design/specs”. This is a Very poor design. Maytag should recall this inferior machine as it does not perform the job it is being sold for.

Such a horrible and expensive kitchen purchase. The stainless looking pieces are either fake or very poor quality - they scratch so easily. After the first year of use the top of the stove looked like it was 30 years old. The oven glass is extremely hard to get at to clean - you have to remove very finicky screws that dont go back into place easily. Oven temp is questionable and it takes a very long time to heat up. I would never recommend the Maytag Gemini oven to anyone.

I dont even bother repairing those things. Customer calls and I say, Sorry, those are worthless. I did try but gave up. Buy Speed Queen. Traditional, heavy duty, with three-year warranty. Whirlpool who owns Maytag doesnt give a crap. They want their warranty repairmen to pass drug tests but no longer give appliance training. Speed Queen is built in Wisconsin. Who knows who is building the Maytag crap. Another customer had a similar problem with Maytag stove, 1 year old. Whirlpool and Menards said, Sorry, you didnt buy the extended warranty. I have conversations with just about every customer about junk appliances these days. Try to find used 20-year old Maytag for quality. Good luck.

We bought Maytag dishwasher and Fridge and Whirlpool stove, the dishwasher, front panel came apart, the seal leak, the motor make a serious grinding noise, wheel on the interior racks were broken off easily. All of these parts will not be changed under the extended warranty by King & State, Whirlpool do not want to respond to our request for follow up. Neither is Leons Store where we bought these appliances. Only after 4 years of normal use.... Think about it! Kitchen Aid, Amana, Maytag, Whirlpool, latest Kenmore same products. BBB is not helping resolving these issues, their method is wait and see. Stay away from those companies. As Info: if you need to rinse by hand the dishes before setting them in the dishwasher...wash them much faster and better done.

I purchased this oven in April 2015. I have had nothing but problems with the unit. The temperature is off. I have had the probe replaced in July and will be done again next week (January 26, 2016). The AquaLift self-cleaning feature does not work. I ran the self-cleaning feature about 8 times and back to back on several occasions. The service providers stated that it really doesnt work and there is nothing they can do about it. The front of my oven, above the vent, is stained from the oven exhaust. They said there is nothing they can do about that either. The last service company that came out for a service call to check the oven temperature came without the proper tool to check the temperature and ended up snapping the propane line. I was given 6 month of a free extended warranty for my inconvenience and told that the company does not replace models. They will continue to come out and repair them. I will never buy another Maytag appliance again.

Refrigerator failed in less than 7 years. In August 2005, I purchased a new Maytag side-by-side refrigerator to match the Maytag appliances (stove, microwave and dishwasher) in the new house provided by builder. In October 2011, I called a repairman because of noise. The relay switch was replaced for $179. Now, I am told the compressor and defrost circuit board need to be replaced for over $700. I will never buy another Maytag appliance or Whirlpool. They make and sell crap and dont stand behind their crappy products.

I also have a Maytag Quiet Series 300 dishwasher. The front panel has stopped working. It was a horrible dishwasher from the beginning. The dishes were streaky on the top rack. And I had to replace the rollers after just over a year. The upper rack has rust on it. The Maytag double ovens I bought at the same time had to be replaced within a year, as the racks damaged the porcelain interior. I also wish I had found your site before my purchases. My husband is not working now. So, I guess we will be washing dishes the old fashioned way.

Ive had my Maytag (above range model) for about 4 months. The same as everyone else with open/close door error. Faulty door switch. When the interior light doesnt come on, I know I will get the error. You would think Maytag would have already repaired or replaced this door switch part.

I purchased a Maytag refrigerator (MBF2258XEB), stove (MER8674AB) and dishwasher (MDB7749SBB) on May 26, 2013. So far all three have been worked on. First, the dishwasher would not fill up with water after the trial run. Called the repairman out. A tag was placed in a position that was preventing the dishwasher from loading up with water. Granted, we should have taken the tag off, however, it stated not to. Lucky for me, I am still under warranty. Second, the refrigerator, which is a freezer at the bottom, started to leak. I thought that maybe we were dropping ice. However, I finally called and had the repairman back out. He knew exactly what the problem was because Maytag knew about it. There was a faulty plug. So in a matter of mins the problem was fixed. Lucky me still under warranty. Those two things happen within six months of purchasing these items. Now, the oven does not work. It heats up to the desire temperature but then cuts off. Called the repairman and he thought it might be the lower baking element. Unlucky for me, warranty has expired. So, $90.00 for service call. Received a called from the repairman, $120.00 for labor and $70.00 for the baking element. I purchased the baking element myself, $58.08 and installed it. Still does the same thing. Now I have another appointment for him to come back out and see what is wrong. Another $90.00! So far I have spent $238.08 on a $699.99 stove. I will never buy Maytag again. Depending on the amount to repair will depend on whether or not I go back to Sears and buy Kenmore. I had Kenmore for 10 years with no problems. I should have gone back to Sears for my upgrade. I did contact Maytag via email. I am still waiting for a reply. Live and learn!

I had a problem with my 1 year old oven. I scheduled an appointment and no one showed up. So I fixed it myself. A week later they called to schedule an appointment and I told them that they were scheduled for last week. So their response was OK, I dont need them anymore - goodbye. The parts are under warranty so I send them the part I replaced myself and the invoice for the cost. I didnt get a response. So 3 months later I send a second letter. Three more months and still no response. I can remember when Maytag had commercials showing their repair sleeping because they had no work to do. Now, their products are failing and their entire service depart is asleep.

I have to say I am terribly disappointed in the quality of my Maytag Side by Side Fridge/freezer and my Maytag stove. Having sold Maytag commercial washers and dryers to coin laundries for over 20 years I expected better. Needless to say..... these are Whirlpool machines with Maytag name plates. Not the Maytag quality that was produced in Newton, Iowa. You can tell these are plastic machines made in Mexico. Of course you still pay for the Maytag name just not the quality. I have always tried to buy from US companies, but my next appliances will not be as Whirlpool is the only US company left with exception to very high end products.

I cannot use my Maytag gas range and oven appliance until I can purchase part #W10213446, which your factory website shows as back-ordered until 2020. This means that I cant cook a meal or have the family and friends Ive invited come to my home for Christmas dinner. I need your help to provide better customer service than Ive received to date through working with the Maytag customer service call center, and the service Maytag parts distributors Reliable Parts and WC May company have received from working through your factory website.Ive owned Whirlpool appliances since I built my home in 1989. When I remodeled my kitchen in August 2010 I chose a Maytag range, fridge, dishwasher and microwave as Id had a good experience with your products for 21 years. Youve built a great reputation for quality products and service, and I hope that you will continue to deliver on the commitment promised in your brand by resolving my problem quickly. A burner control on my three-year-old gas range and oven (model #MGR6775; serial #D00934496) recently stopped working (a Maytag design defect - several screws were too weak to hold the cooktop at the correct level) and your customer service call center referred me to A&E Factory Service for the repair. A&E service staff have been to my home twice and are unable to fix my stove leaving me without a stove for the past two weeks and foreseeable future - as the necessary part, #W10213446, is shown as back-ordered with no estimated time of arrival. The WC May company let me know that your website shows an ETA of 2020 for this part on your factory parts website.When the service repairman informed me that the part was indefinitely back-ordered today, I called the Maytag customer service center asking them to locate and expedite delivery of the part. The line staff and her supervisor let me know that they would not provide that service, as I do not have a pre-existing extended warranty contract for the range. I am willing to pay for expediting the part, but they wont give me that option. So I called the parts retailers covering the western U.S. myself to learn that Whirlpools supply chain is so flawed that it cannot provide a part for a three-year-old range.Whirlpools core principles espoused on your website say that founders Lou, Emory and Fred Upton continually improved their washer; they cared about their community, their employees and their customers. They believed that there is no right way to do a wrong thing. It also states that what truly distinguishes Whirlpool Corporation is our commitment to building strong brands and a loyal consumer base. Were focused on maximizing the benefits of our worldwide network of resources, which is unmatched in the industry.I believe that leaving me for up to two months without a range, so that I cant cook meals for myself every day, and for my family during the Christmas holidays is not living up to your brand promise. Please let me know as soon as possible how you will solve this problem.

Received this Maytag dishwasher model MDW7749SBW1 as a gift from my son in June 2013 when my old dishwasher finally quit. January 2014, the soap/rinse aid dispenser did not work. Called Maytag and they sent repairman who replaced the part. Still did not work so repairman said another part was not communicating with the dispenser so he replaced that part. Worked fine. No charge since it was under warranty. Now its July 2014 and the touch panel doesnt work. Called for repair and was told since it is out of warranty, it will cost about $350 to repair. I called Maytag about this and said that I had a defective appliance. I was told that since I didnt buy the extended warranty, there was nothing they could do. I mentioned my last Maytag lasted 25 years and had only two minor repairs so I didnt see any reason to buy an extended warranty. I thought I was buying a good product. I was told shed register my complaint. Waiting for my repairman to come out tomorrow and see what he can do. I also have a Maytag stove. Wonder how long that will last?

We purchased the Maytag double oven 30 inch 5 burner, stainless steel, model MGT8885XS. Oven worked good for six weeks. The igniter broke in the bottom oven and when the third party non-Maytag repairman came out to fix it, he was unable to remove the bottom oven door. It is not flush and heat escapes when the bottom oven is on and it causes the top oven to get condensation. The repair man was directed from a technician from Whirlpool that he had to order a new seal and hinges. I dont want it fixed. I want a new one. I have called Customer Service for Whirlpool and the third party and the store in which I bought it from and everyone is pushing it off onto someone else. Customer service is poor and stated they will only fix the oven and will not send us a new oven. We sent our rebate in the mail which was to arrive within 8 weeks and we have yet to receive it. Very poor customer service. Glad I purchased the 4 year warranty. I will never buy Maytag again.

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

I purchased a Maytag slide in range from Costco online in April 2020. Within three months a discolouration on the stainless top part of the range has happened. Costco has a ninety day period for repairs, or return on appliances. Pictures were provided to Costco at the request of Maytag. Upon review, Maytag’s response was, This is a cosmetic issue and nothing we will repair. I am an extremely disappointed consumer who will NEVER purchase a Maytag product again.

Had a Maytag Dishwasher that was recalled in 2007 model # DWU9962AAE. I was sent a notice of recall and when I contacted the Maytag staff in the Recall department said that they were sending out a replacement as the unit. Mine was being recalled due to defects in the heater element, which could cause electrical failure and fire. I was pleased they were offering to replace the unit, and within a week or so, a new unit was delivered. This is where the troubles began... the delivery/install person from a local retailer, complained the entire time about having to do this job, was ill-equipped to perform the install, twice he thought he would have to stop as he did not have the correct tools he shared with me. I felt this was odd, if this is the job he did all the time? I asked for a bill of sale or something that would show that this unit had a warranty, and date of install. I was told that in these cases, the local retailer that is contracted to install takes care of all that. I did get the Dishwasher use and care guide, and it seemed like new unit. I had never had a recalled unit of a major appliance. Also since Maytag had my address, phone and email information as they set the install up. I believed the installer. Fast forward to about 2009 and the control panel on the door starts to lose cycles. I decided that since it was just me using the unit and the cycles I used most worked I would not bother with the repair.Fast forward to late October of this year 2015. The dishwasher Maytag model # MDB9601AWW finally does not turn on any longer... I call Sears to have an estimate for repair of the circuit board in the door. I give Sears the model and serial number... and schedule an appointment. The repairman gives me a cost of roughly $600 to replace the circuit board in the door! I tell him no thanks pay $ 59.00 and decide I will buy a new unit... I review many sources such as consumer reports, where it becomes evident that Maytag as a brand is not very reliable. At that point I decide to call Maytag and speak to them about my issues. Two dishwashers in very short order have issues. Also my new unit only had a one year warranty.So much to my surprise when I called Maytag I was informed they did not have any records of my contact information at my current address..? And worse there was a recall on my current dishwasher back in 2010! I was never informed of this, and had used a potentially hazardous appliance for 5 years with no knowledge of this! How could that be though since I was given my current unit by them in 2007. I was very unhappy at this point.... but my disappointment with Maytag was about to deepen.I was also not happy with Sears Home Repair.... They are informed about all product recalls, and had my model and serial number. When those were entered into their computers when I made the appointment and again when the repairman came out and captured that information on my dishwasher himself that should have alerted him to the recall. Not an opportunity to sell me a $ 600 repair that did not even address the defect for the which the recall was issued.So I am now routed to the Maytag recall department.... where all they offer me is a $ 150 coupon for an expensive Maytag dishwasher? So after explaining my situation... and asking the woman I was on the phone with If she would invest $400 or 500 more dollars in Maytag dishwashers, given my experience with 3 failures of their products in two separate units that were not that old? She said she understood. She arranged for her manager Carol to call me the next day at 9:00 am PST. The call never came, and two hours later when I called in they tried to tell me it would be another 24-48 hours before she could return my call? I was now very unhappy. I asked to speak with her supervisor Tim. He too was unavailable, finally after a very long time waiting on hold. I was connected with Amber. I explained again my issues and told Amber that I would like another Maytag Dishwasher to be offered to me..... as this was a very unique set of circumstances... She was willing to let me write letters like this and contact the Consumer Products Safety Commission and lodge a complaint. I am waiting to be contacted by the manager that handles recalls from Maytag. She alleged that they CPSC does not allow the Mfg to assign specific compensation to individuals. That is true....when they are only subject to one failure as part of the recall.... according to the woman I spoke with at the CPSC. However I had not only that complaint; but the circuit board issue and as goodwill gesture to any consumer they (CPSC) have no jurisdiction.... and Maytag could do as they wish. However I doubt anyone but Amber a low level manager, who took it upon herself to make this decision on her own, without even punting to her boss Tim when I shared my story. I just this last weekend bought a new Bosch dishwasher.... and would caution anyone who was considering the purchase of any Maytag appliance of any kind to use my experience as a cautionary tale.

I have a Maytag microwave and stove in my condo kitchen. Both are about 4 years old. Ill never buy another Maytag appliance again. This stove had problems from day 1 and the support was dismal. I had [bought] an extended warranty, which covered nothing (I let it expire and didnt renew). The microwave handle came off in my hand a few months ago. I stuck it back on with gorilla glue. Now it is starting to shut itself off, as if it lost power then mysteriously turn itself back on. Im sure there will be a new microwave in my future and it wont be a Maytag.

I purchased an over the range microwave (OTR), boxing day 2018. It failed January 2021. It worked great before failing. The issue with Maytag/Whirlpool is their service. I told them before they came out that I was only interested in having it fixed if it could be done that day. They checked that they had the parts and said they could do it, so I moved forward with the appointment. Well they didnt fix it, and said that they need to order a part, which they said would take several weeks. They are trying to bill me the service fee $167, and expect me to wait a month or possibly more to get the part and fix the microwave. Now Im faced with having to pay a service fee for something not fixed and buying a new microwave. Lesson: Never try to repair, cheaper to buy a new product. Other lesson, never buy Maytag or Whirlpool product again. Despite what is on their website and advertising, they have terrible customer service.

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

Purchased Maytag front load washer model MHW6630HW from Home Depot. Machine was installed 9/15/19. From inception we had issues that have escalated. Machine leaks and makes strange hissing sounds. Home Depot has no record of the purchase in their website now. We tried to return it within days. We contacted Home Depot executive offices and they keep sending Paradise Appliance repair. The repair people do nothing and keep saying we have to come back again for you to be considered for replacement. Home Depot is dragging their feet and we are concerned about the six month deadline. The Maytag does not do an effective job washing and clothes comes out wrinkled. Concerned about the sporadic leak getting worst and doing damage to floors.

This appears to be a common, known, well publicized problem - freezer drain clogs and needs to be either changed or repaired with a fix, a free replacement part for the drain seal. Easy to install, takes 15 minutes. HOWEVER Maytag will not give you the part!! In order to take advantage of Maytags correction for a well known, chronic, manufacturer defect, you must engage an authorized service person for hundreds of dollars and wasted vacation time waiting at home for them to show up. Unlike any other product, recall this one is not free. My kitchen is full of Maytag products; dishwasher (not so good), range and a refrigerator that had to be replace when the compressor went out after six years. However this is the last straw, Ive learned my lesson, seen the light, THIS IS THE LAST MAYTAG PRODUCT I WILL EVER BUY.

The ceramic coating on the interior of the oven cavity in the top oven, which I use the most (may actually happen to the lower oven in time) has cracked in the exact pattern of the hidden element. When I spoke to the salesperson at the store, he wasnt surprised and said that it will eventually bubble and rust!!! Called customer service and was informed they consider this an aesthetic issue with no fix!!! They will not offer any remedy or compensation. Are you kidding me!!!

I PURCHASED A WALL OVEN ABOUT 4 months ago. Used the self cleaning, oven blew fuse and some other part, had to wait for almost 2 weeks for repair because of self cleaning liner is now peeling and leaving fine particles. Maytag said it was ok, they would not replace, the liner doesnt have a replacement part so Im going to have to buy a new oven to feel safe for my family meal.

When my husband surprised me with a double oven stove I was leery. First Thanksgiving my thoughts were concurred as the 20lb turkey fell from the chinsey rack.....even a cookie tray with almonds fell down.... Unfortunately the lower oven is off by 1/2, no racks work in there. My biggest gripe is that the seller did not exchange it, just tried more racks. Now Maytag will not do anything but allow me to order more racks. This item is a huge piece of junk.

I have an MFD2560HEB refrigerator that I purchased 6 years ago. I paid a premium price for what I thought was a quality product. It has had issues with the ice maker from the beginning, yet I was always able to get it fixed with unplugging the unit for a while. The fan inside the unit stopped working last year. I took apart the entire inside to replace it, and now, 4 months later, the water is completely frozen. Unfortunately, I purchased a Maytag induction stove in May and less than a month later, it is not working either. Maytag quality is not! I asked if I could return the stove, but was told I had to let them fix it. Im still waiting to use my $2,000 stove!

The right front heating element works at the high position only. The over doors viewing glass is too fragile. It shattered while positioning the range. Otherwise, there are no other issues with electric range.

Purchased 4 Maytag kitchen appliances - stove, double oven, fridge, dishwasher - was told that they were all made in the USA. WRONG. The microwave comes from China - not sure why Maytag is not being honest. Not happy with my purchases - even though we spent $4000 to buy American. Warranty service is awful - even extended warranty is a joke. Would never purchase Maytag again.

I purchased all Maytag products for my new home three years age. The dishwasher stopped working 13 months after we purchased it. Since the home was under renovations for the first month, we only actually used it for 12 months. When I called Maytag, they told me that it was either the control panel or mother board and that they could not do anything because the warranty was only for 1 year... and didnt offer me anything to make good on this...NOW three years later, my microwave is displaying error code SE.. control panel is bad. Now I have not had a working dishwasher for two years and this just added salt to my wound. I called Maytag furious that this keeps happening with new products. The only thing they would offer to do is for me to purchase an extended warranty at $350.00 and they would have a repair guy fix the microwave. A brand new microwave would cost the same thing???? They flat out told me that there was nothing that they would do for me, and that they were not going to fix it for free.I filed a complaint with them and never heard back from anyone at Maytag. It seems strange that the control panels craps out within one to three years on two of the four Maytag products I purchased. I WILL NEVER BUY MAYTAG AGAIN... I went back to Home Depot and told them that MAYTAG has LOST me as a customer and that I purchased 4 major appliances from them and two stopped working with in 1 to 3 years. Home Depot was shocked and gave me $100.00 towards a new dishwasher. And I did not buy a Maytag.... I still do not have a working microwave... But when I do have the money to replace it, it will not be MAYTAG. Looking online, I notice a lot of the same complaints about Maytags control panels...... Could it be a scam on Maytags part???

I bought this over the range Maytag microwave model MMV4205DH-1 5 months ago and today a hairline crack appeared alongside the door handle. I called Maytag to find out how I can get this repaired since, as time progresses, it will become worse due to using the handle to open and close the microwave. I was told this was a cosmetic warranty which expired after 30 days. They would fix it only if the microwave couldnt be opened. Apparently, the handle can become loose but as long as the door opens, they wont do anything.I bought Maytag because of their supposed reputation. Im so glad this happened with my $300 microwave as we were getting ready to replace our washer and dryer and were looking at Maytags. Good to know they dont back their products before I spend several thousand dollars on a washer and dryer. I will NEVER purchase another Maytag. My $120 generic microwave lasted 10 years and I gave it to my son and it is still going strong.

wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

We just purchased a house with new appliances. They are Maytag. When I use my stove the oven heats. I have no idea why. I wondered if anyone else has had this problem. When I turn it off it turned off but it turns back on when the oven is on.

I too am a victim of the faulty Control Panel that Maytag put on these dishwashers - Model # MDB7749SBM2. $149 for the part and another $149 for service call and labor - almost half the price of what I paid 2 years ago! Should have stuck with the 10 year old builder grade GE I had with the latch door and turn knob! I am in the market for a new stove and microwave - I will never buy another Maytag or Whirlpool product! When is Maytag going to make good to all the customers out there that have experienced the same issue? If yours breaks it is a very easy fix now that I know. You can order the part and it simply unplugs and plugs in the new one. All you have to do is take the door off and it is right there!

I own a MAYTAG BRAVOS XL* TOP-LOADING HIGH EFFICIENCY LOW-WATER WASHER. On 9/1/15, after reporting a problem, a service person arrived to assess the problem. His diagnosis led to a second visit on 9/8. On the second visit he replaced multiple parts, assuring us that the problem was fixed. When this proved to be false, we called for a third visit; this time a different person arrived. After disassembling the washer he found a large hole and another cracked area in the inner plastic portion of the tub. We made a fourth appointment for repairs, receiving assurances that it would be repaired at that time. I received an e-mail today (9/16/15) informing me that an additional 7 days would be required to arrange for delivery the required part. In the interim, my wife and I are forced to use a local coin operated laundry about every three days, totaling 7 visits at approximately $25 and 3 hours per visit before the next scheduled appointment. The compensation offered, 9 months extension of the existing warranty is woefully inadequate. I want the appliance replaced, as history has taught me that you are obviously unwilling or incapable of repairing it correctly in a timely manner. Additionally, I want the initial warranty that accompanies a new product extended to a full 3 years. We have paid out over $150 and wasted 18 to 21 hours of our time unnecessarily. I expect compensation for the funds spent as a direct result of the bungling, incompetence of your service staff. My questions are these: 1. Was the part defective prior to installation? 2. If so, why did the representative not notice it and refrain from installing a broken part? 3. Why was there no mention of the damage on the first visit? 4. If not, how did the damage occur? Did the service man damage it and fail to report it? 5. What caused the delay in obtaining the part? I have other questions, but will no longer spend any more time on this debacle. I cannot honestly say which is worse, their quality or their pathetic version of customer service.

Omg I am so shocked at all the complaints about these refrigerators.. I too bought refrigerator, stove, microwave, dishwasher from Lowes after a storm just about destroyed our home. I was so excited to have such a beautiful refrigerator and new kitchen...but shortly after it started freezing on the bottom of freezer and leaking all over. My new floors and kitchen cabinet are ruined. Every other day we have to break up ice and clean it out from freezer.. it still then leaks.. several family members have slipped and hurt themselves. Please if anyone knows how to get it fixed without it costing us a fortune let us know. Maytag (Whirlpool) knows it is a defect... Why will they not fix it? I cant afford a new refrigerator and shouldnt have to after only two years.. If a class action comes up.. please contact me. Shame on them...

My stove is approximately nine years old. During the past year both my husband and I enjoy cooking from recipes 3-4 times a week thus the stove has become essential. Functionality and size is important when trying to cook meals with two or three components. One of the oven racks was missing from the oven when we moved into the house. Even though it is self cleaning, spills pile up between cleanings so it is great that it has a really cool steam cleaning option. Just wish it were 5-6 years newer.

I have had 2 Geminis. The first one was fine, this second one is a mess. I have had at least half a dozen parts replaced. I have insurance to have this oven repaired but have paid to have the window seal replaced on at least 3 occasions. The top of the oven is so hot that when I have used the burners to cook on top I have received 2nd degree burns. I have received burns on several occasions. I asked dealer if I could trade this in but said I would have to sell it on my own. I would not subject this oven to another person as I feel it is very dangerous.

We have owned a number of dishwashers, some cost a great deal and some were inexpensive. Our current dishwasher is a Maytag and it has proven itself to be the best dishwasher we have ever owned, not only is it quiet, it cost less to operate and cleans all dishes and utensils excellently.

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

Like so many other consumers, I was drawn to the Maytag name because of what I thought was the high quality of their products and their stellar reputation. So when our old wall-mount oven failed, I sought out a replacement from the Maytag line. I purchased a model MEW5530WDDB17 in 2011 and had it professionally installed. It worked well for a couple of years. Then, suddenly, three of the numbers on the digital control panel stopped working, making it impossible to set the oven to any temperature that included a 4, a 2 or a 5. When I contacted Maytag, I was informed that the unit was out of warranty, but that I could schedule a service call. I had already researched this issue online and knew that the service person would inform me that I needed a new control board and that one could be installed for around $300, and that the new board would come with a 90 day warranty. When I asked the person to whom I was speaking, she said that she had no further information for me. I know that a lot of others have had this same issue with their Maytag range/ovens, and many of them agree with me that we will never purchase another Maytag product.

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

Stove does not heat evenly in oven. Electric burner cannot be turned down to low or simmer, then it will not cook at all. Other burner turned down to low does not stop bubbling and stays at a high temp. There is no consistency. I am extremely disappointed and curse at this stove every day. Model #MER7664XB. Serial #R13316302.

Im furious beyond belief with Maytag. Im furious at myself for being stupid enough to purchase all new Maytag appliances when I purchased this home as I had horrible experiences with them in my former home. This concerns the Maytag over the range microwave oven model MMV4205AA. First of all, within 6 or 7 months after purchasing it while cooking a frozen dinner, the turntable just cracked in half. Maytag wanted $89 to replace it. I knew when the turntable cracked that there were more issues to come. That is not normal in any way for that to occur in a microwave.Problems continued, of course, and with each call to Maytag, they would say the same thing the microwave is out of warranty and refused to assist me. Its not some little table top thing that one can just toss out and buy a new one. I paid about $400 for it from Home Depot. Last week, without it even being turned on, it just stopped working. I checked the electrical supply and conduit to make sure that was okay. I called numerous service organizations who told me this sudden breakdown when the microwave isnt even turned on is a known issue with this model and several other Maytag over the range models. Ive called them (Maytag) three times in the last week and they refuse to provide any allowance and hear the same old thing, the microwave is out of warranty. I was willing to have them even just provide some assistance rather than replace the microwave. Ive been told by numerous service organizations that this is a known issue and that even if they repair it, it will occur again and again and Im best off purchasing a different brand, which I cannot afford. They gave me phone numbers for service organizations authorized to service Maytag products and this just goes to show how out of touch they are. They gave me one that isnt even in business anymore. How professional, not!Warning: Purchase Maytag at your own risk. I give you fair warning. Every single Maytag product Ive ever owned has been a problem. I will never, ever, ever purchase another Maytag product again. I would think just out of decent customer relations, that theyd repair this issue. To be honest, I dont really trust a repair as Ive been told it will happen again and again. There was no notice that the microwave was breaking down either. It wasnt turned on. One day, I went to use it and it just wouldnt work. Actually, I went to use the timer on it and thats how I found out it was dust. My advice is stay away from Maytag. If you read reports, there are more complaints on Maytag than any other appliance manufacturer in existence. Not only on their products, but their customer service too.

I purchased a Maytag built-in microwave and oven combo in 2005 for my newly built home, but I did not move into the house until 2008. So the appliance has only been used for 3 years. The microwave stopped heating after only 3 years of use, which was for microwave popcorn mostly. I also purchased, at the same time, a Maytag cooktop. The knobs had to be replaced, a dishwasher, a rack and utensil holder had to be replaced and a washer dryer that doesnt work properly. I also purchased a side-by-side refrigerator which is okay so far. Im very disappointed in their appliances and they were expensive.

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

I thought I was safe in buying Maytag for all of my appliances in my new kitchen. I bought a double wall oven Maytag MEW6630DDS. I bought it in late 2010 and have had no issues until August of 2018. I rarely use the bottom but used it in August of this year to cook cupcakes. After baking them and leaving the kitchen for a short while I heard a loud explosive, shattering sound. I walked to the kitchen to see that the bottom oven door had shattered into a million pieces. Thank the good Lord that I was not near it. I contacted Maytag to see if there was a reason it would have done this. They said that there had not been a recall. They sent a repairman at no cost to look at it. He came, took it apart and had no reason for why it would have done this. He left it in pieces and said that he was ordering the replacement door. Maytag advised us to turn off the breaker to the oven. After a month without ovens, the repairman called and said that the part had been discontinued. HA! You think?!? It has the potential to explode. It should have been recalled, not just discontinued. Maytag offered us 20% off a new set of $3000 wall ovens or $150 to pick ours up for disposal. Talk about saving the company money and screwing over the unlucky recipient of a defective product. They ought to be ashamed. I am going to have to replace the broken glass with aftermarket glass. What is going to happen when I use the self cleaning option? What happens when the top door explodes. I am scared to use my very expensive wall ovens that I thought would last at least 10 years. Shaneka at Whirlpool said that people have appliances fail all the time and just have to buy replacements. Do all of them have to replace ovens because doors explode for no reason? I am not the only one this has happened to. I have found several other complaints of this on the internet. Why did they discontinue these door? I wonder.

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

My Maytag refrigerator, model number mff2557heb, serial number 10375839gv, was purchased in 5/2005. Two weeks ago, this refrigerator stopped working. I called the Maytag technician and then right away came to my house and find out it is the compressor that needs to be replaced. He told me to search if it is under warranty. I searched in the internet Maytag compressor warranty and I found it and then called the Maytag representative. I told them I have found in their website that compressor of this Maytag is covered for 10 years but labor is not included. Then they asked me to fax it. I faxed the copy on 6/20 and they responded on 6/22. He said they received the copy and he said, Yes, it is covered for 10 years but you will shoulder the labor. So to make the story short, this Maytag representative scheduled Friday, 6/29 for the Maytag technician to fix my refrigerator. My husband did not go to work yesterday, 6/29, Friday, so he will be home for this Maytag tech. Maytag tech came at about 2pm yesterday and when he confirmed that it is the compressor that is the problem, he asked for the warranty paper. And when my husband present the proof, the copy of their warranty coverage that came from the Maytag website, he refused to work with my refrigerator because he said the one in the internet is not valid. It is really upsetting because I faxed the copy of it to them on 6/20/12 and they honored it. Thats why they arranged the technician to come to my house and then my husband did not work for them to work with our refrigerator and then asking me $79 for just saying that it is not covered by the warranty. I even gave them the model number and the serial number of the refrigerator so they can verify if it is covered. He said yes 10 years warranty on the compressor. In fact, two employees that I have spoken to both agreed that it is 10 years coverage except for the supervisor named Rachel. Her employees agreed to 10 years based on the paper that I have faxed them and it came from their website and they dont want to honor it after they sent the technician to my house. Thank you so much for your time and for reading about my grievances against Maytag employees.

Our product was purchased with our Condo. We have had it for 6 months & the first time I called someone was for the oven door being so terribly hot. I was told that was normal. Then I tried the cleaning of it & you would never know anything had been done. It would take a heck of a lot of elbow grease to get the marks off & I dont have the strength or time to be doing that. I had someone come again & he said to do it again, which I did & it still was not clean. I have done it a 3rd time now & still no better. I think this product is a total piece of junk & would not recommend it to anyone. I am a very unhappy customer & will never purchase another MAYTAG product.

Maytag in general has gone from being reputable in the early 70s to being the epitome of a rip-off company that sells junk, then refuses to stand behind it. I have a Maytag Washer and dryer. The washer continually goes out of balance and spins across the floor. Repair people tell us that our floor is not strong enough - funny, our new Samsung washer has no apparent issues with the floor or anything else. Our Maytag Gemini is a piece of crap. The ovens do not work or heat up most days. Maytag pushes replacing an EOC board at $800.00, but then the part is not available. Stove is not even six years old. Maytag is a synonym for junk.

The range I have works awesome, which is surprising for an electric stove. For being 11 years old I am happy with how it is still holding up. The only thing I would improve is if it was a double oven instead of a single!

Ive had my Maytag microwave (MMV4203DS00) for a little over two years. I started getting SE error code. The control touch pad membrane is shorted out. I suspect because the design doesnt allow it to be an over-the-range even though thats the kind of microwave it is! I think the humidity from the burners shorted out the membrane. I called the company and the part would cost approximately $180 for me to fix myself. I have a really hard time believing that one part of a $200 microwave costs $180. Ridiculous. It appears this microwave is designed to fail. Customer service was rude and snarky. The company doesnt appear to stand behind their product. Maytag used to mean something. I had started to replace all my kitchen appliances - microwave, then stove. I thought Id be consistent and buy Maytag based on their reputation. I will never buy Maytag again.

The stove functions are excellent and the temperature of the burners and oven causes the food to cook even. However after about 6 months the heat from the burners causes the coating on the stovetop to burn like its baking and it cant be cleaned. Now the coating around the burners is horrible and burnt.

When we turn up the temp in the oven above 400 degrees, noxious fumes come out giving us headaches and nausea. We have to open all the doors and windows and bring extra fans...very toxic. PLUS the vent for the oven is at the top of the oven door, so the knobs for the burners get so hot you cant touch them!

We have had our Maytag dishwasher for more than two years. Heres how it stacks up: Energy Star rated-Yes; Noise-Almost inaudible except when water runs; Length of Cycles-long except for quick wash 59 minutes; Interior design and loading - 10 out of 10. This is the easiest dishwasher to load and it holds an enormous amount of dishes of all sizes and shapes. Adjustable and removable racks-Yes both. Everything fits including my barbecue and oven racks! Amazing. Stainless interior-Yes including silverware rack. Cleaning- 10 out of 10. Even on a quick wash (59 min) cycle this dishwasher cleans everything! I run a longer cycle just to sanitize if we have sickness in the house. Otherwise it is 59 minutes to finish. Drying-Like most dishwashers this one is only so-so in the drying department, especially on the short cycle. Without plastic containers or utensils the machine dries more completely. However, the amount of moisture remaining after a quick or regular cycle is minimal. The water tends to pool on bottoms of glasses and plastics mostly. Easy to dry by laying a cloth across top rack. Dries in just a few minutes.My only suggestion to Maytag is to work on drying technology to make the machines more efficient and effective. However, that being said, I wouldnt trade this machine for any other. It has every feature I love and a 10-year warranty on parts as well! My machine cost around $600.00. It was neither the top nor the bottom of the line.

Was assured the washer could do comforters, etc. Well, I took a video of the washer doing 5 t-shirt, 1 pair of pants, and 3 pairs of socks on the power wash cycle. Nothing tumbled. All the plate did was swish some water around on the bottom. Clothes werent clean at all. Check my Youtube video, and you can watch the leg of the pair of pants sticking up out of the water and never getting back down in to get wet. Horrible horrible machine. With that said, called the company I bought it from, and they arranged for a front loader since Id only had the machine for a couple hours. Stuck me for a second delivery fee though, which I wasnt happy about. Well see when the new one gets here Tuesday.

Every appliance in my kitchen is Maytag. I went with Maytag because its made in America and now Im annoyed. The microwave died after about 5 years and since I had a spare, I have yet to repair it. I am just now removing the panel to see whats going on in the inside so I can replace whatever broken part is broken. The double oven I have Ive had to repair twice. Once I had to replace a capacitor on the board because it blew. It cost me zero to replace it as I have an old home theater system I part out. The next item was the control pad itself which I tried to repair but had to replace for $200. The dishwasher died after 6 years of use and after replacing the control pad (couldnt be repaired), it still didnt work. And I got a replacement from my wifes dad who was moving and had to get rid of his. Ultimate timing. I purchased a Maytag refrigerator instead of a Samsung like an idiot (which I suppose I am at this point). The fridge leaks water because the drain plug is jammed and it will take a lot of work to get back there to unjam it. I think Maytag wants to sell you expensive parts that are doomed to break after a couple years of normal use. They want to send repair guys out to your house to charge you to fix their junk. I cant wait to move and buy all Samsung products and do away with this Maytag relationship once and for all.

My complaint is not against Home Depot but Maytag Products. They are inferior products. Stay away from Maytag! Note: We are in our mid-to late 60s, no kids using these products and they do not get a lot of wear and tear. Maytag Microwave: MMV 4205DS-0, May 29, 2014 we purchased Maytag appliances for our kitchen (stove and microwave from Home Depot). I liked the 10 year metal warranty plate attached to the front limited warranty of the microwave. This means nothing! They cover the stainless cavity of the microwave (a part that will never go bad). June 3, 2014 this microwave was delivered. Thanksgiving, the microwave went out November 30, 2015 this was replaced with GE Profile Model JVM3160RFSS for $178. November 30, 2015, Diamond Factory Service was here for the Microwave. We paid $90 for the service call. They wanted $228.09 to repair (1-8206419 Switch $15.22; 1 W10269460 Switch $27.03; 1 W10727360 Microswitch $27.03 and Labor $155.00). Maytag Dishwasher MDB7749AWM. Purchased from Al race Appliance for $599.95 total with tag etc was $920.27 on 5/16/12. So thankful was purchased the additional warranty for five years. We have had 2 service calls so far for the same issue, which is W10356494 Console CMFF0312434. This is a known problem (it will not start). I wish I would have googled the model before purchase was made. When the warranty expires, this will go to the curb too.Also, purchased Maytag Neptune Washer and Dryer from Best Maytag, Rockford. The dryer had problems with the circuit board after a short time. Too expensive to replace. Our family and friends ALWAYS purchased Maytag only. No more! Stay away! We are waiting for the oven to go next. Oh and check out the bottom drawer. There use to be room for pots and pans. No more. Lucky to get your pot holders in there.

Purchased the Maytag Aqualift self-cleaning oven and this feature doesnt work at all. I would have never have made this purchase if I knew the oven would not self clean. This technology with the water in the bottom to self clean is pathetic! I thought maybe it wasnt working and called for a repair since it was under warranty. The service man told me not to expect it to clean like a regular self-cleaning oven. But I complained that it did nothing at all! So now I have a self-cleaning oven that I have to clean myself!

I am at my wits end, as I try to get some satisfaction for the fact that this stoves cleaning system does not work! We purchased this stove at Home Depot in Hadley Massachusetts on February 2, 2014, and it was installed in a seasonal cottage that we were having renovated. When we arrived at our cottage in May, I was delighted with the stove. The cook top performed well and the oven size was great. During the summer, we tend to grill outside so the oven didn’t get much use, but it perform perfectly every time I used it. I always remove any debris that may have spilled immediately, and didn’t see any need to user the AQUA Clean feature until we were getting ready to leave in October. When I ran the cleaning system as recommended in the manual, there was a stain on the bottom of the oven. I then ran it eight (8) more times with the same result.I called the service number and they scheduled a service technician to come for a visit. He said that the stove was working the way it was designed to and unfortunately since it really didn’t get hot enough to do the job, the stain (and with more use, more stains) would remain. He also noted that should I try oven cleaning products, my warranty would be voided. This was not the answer I was hoping for, but since his visit was on the day before we were heading South for the winter there was not much I could do.Have called the service number several time since then, asking what could be done to rectify this problem with no positive responses. One did say that they could send the service tech again and went so far as to schedule an appointment for January, which she suggested I postpone with the technician until we return in May. The reasoning being is that since the warranty is only for a year, and the cottage won’t be opened until May, the fact that the original appointment was within the warranty period would cover the cost of the visit. When the technician called a few days later, the scheduler said that it made no since to go again, unless Maytag came out with a fix for the cleaning system. Since it’s not broken, but just does not work. I again spoke with a service rep and asked if anything could be done or if I could speak to a supervisor, she said that one would call.. That was weeks ago and still no call.We purchased this stove with the hope that it would last for many years, especially since it is only used for five months of the year. Ease of cleaning the oven is important. Home Depot no longer sells this model, and after some searching the internet I have found that I am not alone with this issue. Apparently it is quite common. We will not be able to access the cabin until May 2015, but would appreciate anything you can do to expedite a replacement of this stove, with one that actually self-cleans or a refund.

My four year old Maytag stove blew out the lower heating element in the oven. The model number is MER8880AW. I removed seven small screws to confirm what the problem was and remove the element. That is a short life span for a stove element. My wife checked our paperwork and thought it indicate the part was covered on the 10 year warranty. Called Maytag at 9 AM and went through the press numbers thing, being put on hold, call dropped, told they were not open twice, etc. Finally got a person to talk to at 2:45 pm. Yes the part is covered under warranty, but no they will not give me the part.A repairman must plug it in and put the seven screws back in. This will cost me a lot more than the $50 the part cost me at the local appliance store. 10 year warranty. Wow, WORTHLESS! There WILL NEVER BE another Maytag or Whirlpool in my house. Making a big deal out of their warranty when they are going to soak you bad for a simple install is just plain dishonest.

First we design the cheapest, flimsiest drawer possible on the bottom of the stove. Then we mount it on cheap plastic guides on a flimsy metal track. What a joke! Listen, drawers have been around over 700 years. If you cant do better than that, you need to look for another line of work.

My model has 2 ovens which I love. A smaller one & a regular sized one. It also has a cooktop. The cooktop always has “marks” on it from the pots & pans. No matter how careful we are, the pots leave marks. We even bought new pots & they leave marks. Something that we do like is that 2 of the burners have “select a size” so these burners can be used for small or larger pots.

In 2013, $1850.00 I purchased a Maytag double oven, $700.00 Maytag dishwasher, and a Maytag refrigerator for $2200.00. I have had nothing but problems with all of them.... The oven locked up on me had to call a repairman to fix it. Ive had to replace the control panel on the dishwasher... And the refrigerator!! (WHAT A NIGHTMARE) In 2013 just received the appliance they had to install a heater in the ice maker because there was condensation. 2014, Refrigerator dead.. Repairman had to replace interface and control board.. 2017, Icemaker crashes and had to be replaced... 2020, Now here we are again Ice maker crashed again! (JUNK). My wife told me that she has had nothing but good luck with Maytag appliances... Never again.

If I can rate the AquaLift Technology oven cleaning system that my Maytag oven has as a “Zero”, I would. This technology only removes some of the spills on the bottom of the oven. It does not clean the sides or top of the oven. I’m back to the olden days of using a lot of elbow grease to remove splatters and spills. They say you cannot use any cleaners in the oven either. At least with the old ovens you can spray an oven cleaner and wipe it clean. This product has taken us back before there were spray oven cleaners!

148013 Stan & Pauls Dartmouth MA - 3 yrs ago we remodeled the kitchen... I went with Maytag appliances because I was always told they were good. I should have stayed with GE. Dishwasher touch pad is gone again... 2nd time in 3 yrs. Last one cost us 265.00. We are senior and thought these appliances would outlast us. We only use it about twice a week. Our freezer door tracks and door needed to be replace 6 mo after purchase. WE lost all the food that had defrosted. Our oven coil burned out already also... that was expensive to replace. Only thing that we have not had to repair (knocking on wood) is the microwave. STAY AWAY FROM MAYTAG, FOLKS!!

I purchased a Maytag Dishwasher (MDB7749AWW1) just over a year ago from Sears. I did not get an extended warranty since the appliance wasnt over $1,000 and I thought I would take my chances. Sure enough, about one month after the warranty expired, it all falls apart. There is something wrong with the control panel and I cant get anything to work. Ive been looking online and see that this is a common problem. So rather than throw more dough into the money pit, Im purchasing a new, simple, uncomplicated GE Americana washer from Home Depot for $279. I figure this will cost me less than going through the repair dance with Sears and Maytag. I will never purchase an appliance from Sears again. Ive been through the mill already with a $2,000 Jenn-Air range that has broken down five times in the past three years (2 times it was the control panel). I was lucky that I purchased the 5 year extended warranty on that one, but never, ever again will I deal with Sears.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

I bought 4 appliances - stove, refrigerator, dishwasher and microwave. Just after 1 year, our dishwasher stopped working. Serviceman said it was the motherboard. I had to talk with a supervisor in customer service to get it covered and found that it was only a switch that was bad. Next, our ice maker overflowed with water, causing damage to our new hardwood floor. Again, I had to talk with a supervisor to get this covered and I did not file a claim for the floor. Then, our stove shut down. Repairman found that a wire was shoved into the top box, causing them to be exposed and shorting out the system. Now 2 years and 4 months, our microwave is not heating and I have to call for service. This was a brand-new kitchen that was remodeled and all appliances were new.I am very disgusted with Maytag products and their attitude of We are sorry, but there is nothing we can do as the warranty has expired. It used to be 3-year warranties for Maytag products until they were bought out. Never will I buy their products again. Have been married 40 years, and our other appliances for 38 years never failed and to find that these products are made in the USA.

The steam/heat produced by the oven has made the electronic (digital) control panel buckle. Yes! This is a thousand-dollar (plus) stove, and it has warped, through no fault of mine. When I want to cook something, I press the keypad to enter the number of cooking degrees that I want. The problem is, the control board is not working correctly. Regardless of my typing in 350, it will default to 100 degrees and stay at 100.As a teacher, I do not have a huge income. I was disgusted with my recent repair estimate of $80 for a service call, and a quote of over $600 for the replacement part, plus some not-yet-determined labor installation costs. Calling the 800 phone number for Maytag connected me to some local people working as independent and overpriced contractors in Los Angeles, California. They are not MAYTAG employees, so they are not well-informed about the product.I miss the time when manufacturers stood by their products, and had factory-trained and authorized employees available to make repairs. I bought this monster Maytag stove from Lowes. I am disgusted with both companies. I have gone online to research buying my own part and hiring a local yokel to put it in. Most everyone I have encountered has been a rip-off artist. I am teaching your kids and grand kids to read and write, and you dont want to help me repair my stove without price-gouging. I can use the burners to some stove-top cooking. Life has become a hassle without being able to cook.

I purchased this at Home Depot October 2013. The oven heats well. I like the upper and lower oven feature. The broiler works fine. I rarely cook using convection. The self-cleaning feature, to this date works fine. Dislikes - the stainless is cheesy and scratches easily. The knobs on the front are of poor quality and the cook top stains easily and does not come clean. Disturbing - the gas cook top has come on twice with simple bumps and gone unnoticed for a period of time. Usually, you hear the clicking with the gas turning on, but not always. MOST DISTURBING - last night, 1:30 in the morning, I wake up to the heavy smell of gas. Neither my husband, nor I cooked that day, at all. I walked out to the kitchen (opening windows along the way) and the right front burner knob was turned just enough to expel gas, no clicking noise, no flame. This being the third incident (that I can recall), I think this appliance should be recalled. The knobs are not secure/safe enough to be on a gas appliance. Aside from the hazard described above, I too am dismayed at the fact that drips go between the glass and there is no way to clean it. Another poor design flaw.

Purchased this double oven back in 2012 and have had to have the control valves replaced twice because of them jamming and snapping. The burners are undersized for cooking and it takes forever to get water to a rolling boil. The broiler in the upper oven needs constant attention when using it because food cooks unevenly and burns quickly. The lower oven is great, convection is awesome. I have seen the Maytag repairman more from my stove than I have for any of the other appliances I owe combined. Maytag should stick to appliances that only use water.

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

I purchased my Maytag gas range (model number mGR7665WB) on Thanksgiving 2011! It worked fine until May 2012. Then the bake function just stopped working. If I select bake, the temperature fails to rise above 100F and a sickening gas smell fills the kitchen! PC Richards, where I purchased the product from, sent a repairman who took two weeks and two visits to fix the part! Everything was working fine until six months later during cooking for a full house on the day of my daughters birthday party. Same problem, bake function failed again along with gas smell! I was pregnant at the time and very worried about the gas smell! We had to leave the house a few days after that due to the hurricane and when I returned, everything worked great for a few weeks only to fail on Christmas Eve leaving me to cook the meat for our Christmas Day dinner in a neighbors house, highly embarrassing and inconvenient! Now Maytag and PC Richards are only able to repair at a high cost to me which I cant afford and feel I shouldnt be responsible for as this product has been consistently unreliable and possibly dangerous. I am especially concerned about the gas smell as I have a newborn and a 3-year old in our small apartment!

Whirlpool owns Maytag and it appears that selling poorly made products is now their focus. When I purchased this Maytag 30 Gemini double oven range, I thought I was buying a superior product. Now, I am on my 3rd repair. When would it fail, on Christmas Eve morning when I am trying to prepare dinner for 20 people who are coming for dinner party. I paid too much for this piece of junk. From now on, I am buying from the scratch and dent sale because there are no quality appliances manufactured today. Buy cheap and it wont irritate you so much because no one especially Whirlpool owned companies focus on quality.

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

2 years ago I purchased a Maytag Washer & Gas Dryer. Unfortunately, I did not invest or believe in extended warranties. I believe in trying to buy quality products. The door on the washer would not open and 2 error codes were displayed. I was trying to add another piece of laundry and the washer had just started. I canceled the load, waited for the door lock light to go out, but the door would not open. The error codes began displaying E3 and F5. I immediately went to the Maytag website for a resolution. The suggestions did not work and was instructed to obtain service if they did not. I called for a service call for $35, but was told that the repair would be over $300 for parts and that was not including labor. The parts I needed were a control panel and a part for the door lock. This was not a Maytag Company service tech and he told me that this happens because the parts are plastic. Currently, besides a Maytag Washer & Dryer I have a microwave, stove, and dishwasher that are also Maytag. When I replace these appliances, I WILL NEVER BUY ANOTHER MAYTAG PRODUCT. I expect the quality and life of an appliance to be more than 2 years, without buying an extended warranty. When I told a friend what had happened with my Maytag Washer, she told me that she had a Maytag Washer broke down with a control panel problem, and she couldnt remember the other part. She informed me that her repair was over $500.

I purchased a Maytag over the range microwave a couple of years ago when I had my kitchen remodeled. I have had it repaired twice already. Each time, it cost over $150. I bought this product with confidence that it was a quality product. To say the least, I am very disappointed and I will never buy this brand again. My previous microwave lasted over 15 years without a single problem. The only reason that I got rid of it was to have matching appliances. It was not a Maytag. I am looking to buy a new microwave and I will be sure to look at the reviews to prevent being suckered again!

I have never liked the stove because it is too small (it came with the triplex) and it has porcelain like top. One burner burns to hot, the other three mediocre, there isnt enough space between the burners and the back of the stove. It doesnt cook evenly and it really does not have a low or simmering setting. You cant set a timer for simmering because it cooks too fast. The knobs are stuck and sometimes wont light when you turn them down. The oven is okay, but could be better. Wish it had self cleaning. The broiler in no existence. Food way too close to the flames. We have had this oven since we bought the triplex back in 2011.

Maytag Quiet Series 400. Only good thing is the 3 spray arms. The racks are arranged in the worst configuration so you cannot fit many dishes in. The controls are extremely confusing. They do not seem to work in a logical way. The manual is of little help in figuring out how to operate the machine. I dont use the drying feature, so the only options on the panel that work together are Normal and Hi Temp Wash. Ive never had a dishwasher that took 2 hours to wash, but the settings dont allow for a smaller load or shorter time. The rinse agent receptacle is confusing and difficult to understand and use. Way too complicated compared to earlier dishwashers that Ive used. Would not buy this one again.

My refrigerator was delivered on April 3, 2016. I began calling for service July 2 when the bottom freezer door started depositing ice chunks on my kitchen floor every time we opened it. An appointment for service was made for July 18, service never showed up. Another appointment for August 3 was made and again service never came. I called the 800 number on Aug 19 again arranged service for Aug 24 after hours so that we did not have to take anymore time off work. When repair finally looked at the fridge they said the door was not aligned and did not close so the frost builds up and breaks off onto the floor. This can be fixed with a new door that can take from 6 weeks to 8 months as they are not stocked and have to be made at a factory. The fridge constantly runs and is starting to leak water through to my kitchen floor and basement ceiling tiles.I called Maytag/Whirlpool on Aug 25 and the service agent told me the best they could do for me was extend my original warrant by 6 months while I wait for replacement part and they advised I purchase the extended warranty. The second agent named Gabby I spoke to advised me to call Home Depot where I purchased the fridge to see if they would do something for me. She would write down my concerns but had nothing more to say or do for me since the repair person deemed the unit repairable and a part has been ordered. I called Home Depot on Aug 25 and I spoke to Appliance Dept who told me the manager who could help me was off that day. He advised me to stick weather stripping around the door to seal the leaks. I said I was hesitant to do anything that may void a warranty and he agreed. He suggested I may get a loaner fridge but I have heard nothing yet. I want a replacement fridge.When you pay $2000 for a fridge it should be worry free for at least a year? I have been reading reviews and I am wondering why this is not a recalled appliance as this seems to be a very common problem. I am sad that Whirlpool is not standing behind this product. Home Depot has been in touch with me regarding this fridge issue and the lack of customer service provided by Maytag. They are replacing the fridge on Sept 9th 2016 and taking the old unit away. Home Depot has tried to get in touch with Maytag and they have not gotten a response at all about my faulty unit.The staff at Home Depot in Peterborough have been excellent to speak to and have apologized for the issues with getting service to my appliance. I am very grateful to them for their assistance and for following up with me in this matter. The downside is that I am getting another exact Maytag unit as a replacement so hopefully this does not start all over again. Home Depot has been a great retailer to deal with. I am very saddened to hear that even Home Depot cannot get responses from this manufacturer. I have also lodged a complaint with the Better Business Bureau.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

I bought all new Maytag appliances for a new house built 2 years ago. The oven fan, while in warranty, began coming on in the middle of the night. It would turn on, cancel, began not working, and then the ticking noise began. Maytag sent 5 different service people out, sometimes without the part. We are afraid to use it now and have turned off the breaker for it. Now, it is turning itself back on again. Maytag says we must now pay for any repairs/service calls as it is out of warranty. It was not out of warranty when all these troubles began.I called Maytag customer service today and could not have talked to a less customer friendly person. She didnt care that it was in warranty when the trouble began. It is out now and is our problem. There is no one else but her we can talk to about it. She is the decision maker. What experiences has anyone had with trying to call the president of Whirlpool, or filing a small claims court action? Any help is appreciated. Who is going to cook our Thanksgiving turkey?

This is my first convection oven. It is a double oven and I am hooked for life. I love the smooth top and use the convection daily. The only small issue I have is that the touch buttons on the range are on the harder side to push. But other than that, I have owned this for 5 years or more and would only get the same type again if I had too.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in Nov 2013. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within first 13 month. Then another valve got stuck about a year ago and the third one got stuck today Nov 19. So far I spent $400.00, just for 2 of them and the last one has not being replaced yet. This is a safety issue, because it always happen when the stove is on and will not turn off. I need Maytag to replace my stove because I am afraid this will burn my house down. I bought Maytag because they always advertise as quality product, and now I have to live with the nightmare of burning my house down.

I purchased a dishwasher and stove from Home Depot. Stove has already been replaced twice because of faulty manufacturing and now the dishwasher, after 1 1/2 years no longer works due to the control panel. I called a repair representative of Whirlpool/Maytag and explained the circumstances. Their own customer service people indicate that it is cheaper to replace a product then it is to repair it. Shame on Maytag and Whirlpool that they move their companies to countries outside of the United States and they no longer stand behind their product. Shame on them that what use to be the best product around is no longer worth paper you print on. I will no longer purchase any product from Maytag, Whirlpool or Home Depot since they all seem to line their pockets from products they know wont last. One mouth is worth a thousand complaints and I plan on screaming from the rooftops!

Maytag washer, dryer, oven, microwave over-the-range - all crapped out in four years. I will never buy or recommend Maytag. I believed them to be one of the best brands but apparently theyve learned a few too many shortcuts.

Back a couple years ago, Dec. 29, 1983, I purchased a Maytag washer, model A209, and a Maytag Dryer, model DG110. Im still using them daily. The washer has given NO problems, other than the brake has taken to squealing. This causes nothing more than a notice that the load is done, so no repair is necessary. The dryer has proven more problematic, as I have had to replace the ignitor three times, the blower fan twice, and the motor (and belt) once. I still think I have gotten my moneys worth.

Purchased this oven at Lowes on 2/8/2018 for $1925. Worked good until my wife cleaned the lower oven on 11/22/2019. The next morning the oven was locked and nothing would work. We called for service and the repair bill was $194.55. I told the repairman that the oven had a 10 year warranty on it, one year on everything and the rest on the parts only. He said no, and showed me in the warranty book that it only covered two parts. Which was not the two parts he had to replace. If you purchase a oven with self-clean feature, I would recommend that you do not use it.

My new dishwasher had a defective board and worked erratically. Shortly after the warranty was up it stopped working completely. I contact both Maytag service and Home Depot on several occasions with no satisfaction. This a well known defect. Apparently the board replacement and service would cost in the range of $250-300. Too much for me as a senior on fixed income to justify. No dishwasher for almost a year. I then read an article indicating there was a class action settlement in California on the same make and model. I called Maytag again and after spending 2.5 hours on the phone I finally reach a person who sent out a service repair person. This person showed me a memo confirming the problem with the board. No recall but... if a customer is persistent they will give you the board. Finally new board installed at no charge.

The Aqua lift cleaning system is a complete joke. Have had to replace oven light bulb 6 times in 11 months. Control panel is completely discolored. Expected far more from a Maytag product.

I live in Southern Indiana and bought my appliance from Charlie Wilsons for 25 years. 3 years ago my Whirlpool washer quit filling up to full level. I decided to move it over and use for my car and pet towels. When I bought my hose in March 1999 every appliance was Whirlpool washer, dryer, refrigerator, stove, dishwasher. GE is made in Louisville, KY but I dislike the union.Anyway I bought a Maytag model MVWC415EW1 June 2017. Recently it started making a grinding noise when going in spin cycle, wadding cloths up and leaking black water on basement floor. Called repair shop out. I just do not have the time to repair stuff anymore. They came out $80.00 service call and tell me at least $300.00 to repair. Wait a minute. $500.00 to buy a new one over $300.00 to repair. Guess what I did? I called Maytag and complained. CASE NUMBER **. They reviewed and denied. Not a problem. I said, I guess you do not need me as a customer anymore.I have twenty year old Whirlpool washer and dryer still running, I have replaced my refrigerator (Old one in garage still running a colder than new fridge and day of the week). Bought Amana=Whirlpool and it has quit and replaced with a Whirlpool July 2019. Nothing is built like it used to be BUT we still pay as much if not more. Off I go to Charlie Wilsons to buy a $1000.00 Speed Queen washer with 7 years parts and labor warranty. Had to order it but old washer still running just not going to full mark.

The bottom oven of my Maytag double oven range (serial #MER6765BAS18) caught fire while I was baking there. The coil burnt out and separated. This did not occur due to food spill or other means. The coil was charred. The stove top does not perform adequately and the coils do not heat uniformly.

Purchased this Whirlpool made Maytag Stainless Steel dishwasher Feb 2013. By Jan 2017 the washer was no longer operational. Due to poor factory design the touch pad wiring harness was crushed during the initial assembly. The harness is routed behind the touch pad/pull handle faceplate in the door. The factory design provided no clearance for the harness. Obviously after little use (opening and closing of the door) the pinched portion of the harness behind the pull handle becomes compromised causing the ELECTRICAL SHORT.I phoned Whirlpool the maker of the Maytag Stainless Steel Dishwasher for assistance, all they offered was a repair plan in excess of $300.00. I purchased this supposedly quality American Made Whirlpool product as well as a range, microwave, washer and dryer in the spirit of supporting US labor. Now Im stuck with a dishwasher that has an ELECTRICAL SHORT, possibly a FIRE HAZARD and Whirlpool trying to milk me for more money. Please think twice before purchasing anything from this Michigan based company.