Brand new Maytag dishwasher, model #MDB6709AWBO, installed after one year warranty because of extended time needed to complete kitchen. It just never worked. Repairman says control panel faulty. Sears wont help or replace. Sears’ service is extremely poor, over one hour on phone transferred over and over and then told too bad by a Supervisor. After checking this site, I realized Maytag suck. And what to do now that I paid $700++ for fancy dishwasher that doesnt work. By looking at other peoples complaint, it will break down over and over.

Same as all the others, bought this dishwasher about a year and a half ago for a new home. Didnt get the CO until 3 mo. ago and already having same problem with the keyboard flashing and not working properly. Very pathetic to believe less than 100 washes and were going to need a new washer, that works out to be about $ 5.00 a load. Wish someone could help. Model mdb7749sbb0. Thanks.

Bought new and only had one service call in 20 years. The control panel was replaced. Since then, the dishwasher has performed well and, factually, was far less expensive than many other models! That figured in our decision when remodeling our kitchen back then.

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

The dishwasher is only one and a half years old and like many others are having trouble with the control panel. The model is MDB89495AWO which cost nearly $800. The dishwasher does not shutdown after an operating cycle. On contacting Maytag with the symptoms they advised that they have never heard of a similar problem. On reading the comments/experience of other Maytag owners I am undecided whether to scrap this unit and buy another make!

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

I bought a Maytag dishwasher on June 2008. This new Maytag dishwasher replaced an older Maytag dishwasher that caught fire and was recalled (I found this out after calling Maytag). The new dishwasher (Model: MDB 5601 AWB) also had a recalled part (heater coil) in February 2011. Two months ago, (the unit is now 3 years old), the control board started malfunctioning (certain cycles no longer work). I called Maytag today (Aug 24, 2011) but I was told by a Maytag representative that there was nothing that they could do. After reading so many complaints, I am ready to file a class action suit. It seems that this company continues to perpetrate fraud against an unsuspecting consumer for they knowingly continue to manufacture defective products.

Maytag dishwasher does not clean dishes. It has hot water and we have had a repairman look at it and he said water jets working. We have to wash all our dishes by hand before loading them into the dishwasher to sanitize.

Same issue as everyone else. After about 15 months the control panel on my Maytag dishwasher model#MDBH979SAM1 has malfunctioned. First it would only let me choose the rinse option but now all the lights are turning on and the dishwasher will not stop washing but yet the dishes are still dirty. I called Maytag and they quoted me 249.00 to fix the issue. But if its a common problem with this make and model why do I have to pay to replace the panel. They should recall this model or replace the panel with an updated one that wont have the same issues! I cant imagine paying 249.99 every year to replace this panel that seems to malfunction no matter what you do!!! I paid around 550.00 at the home Depot for this dishwasher! It did not even last me two years!!! I want a lawsuit filed against this company and I want my money back or my dishwasher replaced with one that works and wont have the same issues!!!

The dishes need to be washed off to be sure they will be clean. It holds a lot of dishes. You can put it on a short wash or long one. Leaves water on base of glasses sometimes. Holds moisture. Heavy wash, normal wash, light wash, rinse only, auto clean, delay 1-9, heated dry, sanitize, tough scrub, extra rinse. Regular size 24. Beige color. Electronic buttons. Maytag Quiet Series 200: I do not like the racks for putting dishes in. Otherwise it holds a lot. It does not clean dishes if you do not rinse them off first. If you run the dishwasher immediately after putting dishes in it will clean them off. Sometimes it leaves water standing. Even with what I have said I really like this dishwasher. We have had the dishwasher a long time. We use it at least 2 times a week.

My wife was in the kitchen and started yelling for me to get in there fast. I could smell smoke and then could see the smoke in the kitchen and sparks coming out of the front top right side of the dishwasher. I shut off the power to the dishwasher at the breaker panel. I then removed the contents and then the dishwasher itself. I threw it outside and then the next day I took apart the door and found that the control board was melted and fried. The model # is MDBH949PAM1. We are trying to locate the receipt for date of purchase. Pictures are attached. This is not safe and my wife is very upset as our 4 year old daughter had been leaning on the door not just 15 or so seconds before this happened.

I purchased the top model Maytag dishwasher, and within four uses, I noticed major water damage to the side of my cabinetry. I pulled out the dishwasher and realized it was coming from the side unit where water enters the tub. These things happen, and I phoned their customer service department expecting this unit to simply be replaced, being that it was less than a week old, and that I would have been left a satisfied customer. They were willing to send a technician over to try to fix the problem, but not replace it. I now have to replace my cabinets, and maybe even my granite as it may be damaged in the removal process. I am not asking them to fix that even though the damage was caused by their dishwasher, but a new dishwasher, I did expect them to cover. Their customer service stinks, and I suggest to anyone that if you have any problems with a new unit, the best thing to do is return it to where you bought it. Im sure they will gladly give you a new unit and send the bad one back to Maytag. Dealing with Maytags customer service is the worst thing you can do. They do everything in their power to not replace it. Instead, theyd rather lose a customer for life. Whats sad for them is that Im a builder, and I usually build approximately three houses per year. Thats a lot of units theyve lost sales on over a simple replacement of a dishwasher. Its not a good way to do business. The bottom line is, stay away from Maytag.

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

My Maytag dishwasher is a nightmare. I purchased it in February 2013, started having problems with it turning off a week ago. I called Maytag customer service on Wednesday and was told I had a service call scheduled for Friday. I took the day off of work to be available for the repair service. I was given a phone number for the repair service. By noon I was wondering when I would receive a phone call to let me know when the technician would arrive? Then I was told that my appointment was scheduled for next Tuesday... ARE YOU KIDDING???? THAT WOMEN FROM MAYTAG CUSTOMER SERVICE LIED TO ME ABOUT THE DATE OF SERVICE!!!! I spoke with Scott, customer service representative (manager) and he told me that I was sent an email with confirmation. ANOTHER LIE!!!! I HAVE NOT RECEIVED ANY EMAIL FROM MAYTAG. I would never buy another Maytag appliance.... They DO NOT STAND BEHIND THEIR PRODUCTS. LOUSY CUSTOMER SERVICE... SUB PAR TO SAY THE LEAST!!! Very dissatisfied customer - wasted my time and are not willing to make it right.

Our current dishwasher was already installed when we purchased this house. It is adequate, however, it does not do a great job with caked-on food. This means that the worst dishes need to be pre-cleaned.

I have on the Maytag dishwasher for about a year. Is very quiet, the dishes are not clean. I called three repair guys from Maytag. The first time they replace the pump. Second time the guy said he just had a designed machine is no good.

About 4 years we purchased a dishwasher model # MDB7749AWM2 made by Maytag.The first part of Aug. 2015 it quit working. I had a repairman look at it and he said it was the control panel and he would order one. He ordered it and we waited a couple of weeks, no part. He called about it and they told him Sept. 9th it would be sent. Sept. 9 came went and no part. He called them again and they told him they had no record of the order. So he ordered it again in few weeks, was told it was back-ordered. This happened a couple more times and I told him to cancel the order. I would go buy a new one but not a Maytag.

I had bought Maytag Dishwasher MDBH979AWW3 in Sep. 2009. Oct 2011, the dishwasher stopped working and the control panel had to be replaced, few days later, it stopped working again and the Thermal fuse had to be replaced. Now two months later, it stopped working again. Till this point, Ive spent a lot of money on the repairs and I wish I had used that money to buy a new dishwasher. Looks like not just the Maytag dishwashers are faulty, but even the parts they have are faulty. I will not recommend any Maytag products to anyone.

Maytag dishwasher model MDB7759SAB, 1 year old and control panel will not work at all. Maytag site does not recognize model #, got part numbers off parts and cant find the parts. Looking for control panel, cant find black one and others are back ordered for weeks. After reading other peoples problems, it seems Maytag would correct the issue.

Model MDB7749SBM1, Complete FALSE ADVERTISEMENT and GARBAGE. Let me explain. Maytag clearly claims this dishwasher is stainless steel on the inside and out... FALSE, BOGUS CLAIM. Please check for yourself, tried a magnet to it everywhere and the magnet stuck everywhere. I have had this dishwasher for 15 months. The keypad frequently stuck. When I called Maytag, they told me if its usable, there is no defect. 15 months after purchase and 3 months after WARRANTY ran OUT on Thanksgiving Day with 25 guest. The keypad finally quit for good. I called the Friday afterward and was told no service for a week. I called and received local service but they told me it would need a keypad, which I waited to call on Monday since Maytag is closed on weekends how ironic. I was told they wont cover anything since a certified person didnt come out even though nothing was ever fixed and they blatantly lied to the consumer. Tried to sell me an extended service plan. I will NEVER BUY ANOTHER MAYTAG PRODUCT AS LONG AS I LIVE AND WHEN IM IN LOWES OR HOME DEPOT, I WILL TELL EVERYONE IN THERE SHOPPING THE SAME THING, DONT BUY MAYTAG IF YOU KNOW WHATS GOOD FOR YOU.

My experience is very similar to Richards below. I have an MDBH979AWS3 that was purchased new in April of 2010. Just over one month after my warranty expired, the touch panel ceased to work. Since it was no longer in warranty, I had to replace it out of pocket. The wiring harness to the old panel looked heat damaged. Last winter, the central computer died. The machine was useless. I called Maytag customer service and actually seemed to find a sympathetic ear. They agreed to a new part if I paid $129 for one of the two companies doing certified repair to install it. During the summer, it blew several fuses. Then in late November of this year, the touch panel went again. I hesitated on how to respond and waited until after the holidays to call them. I got the most rude customer service rep that Ive dealt with in a long time. Somehow, I was blamed for a misdiagnosis on the computer panel (duh, no, that was a different issue and it was indeed broken), accused of misuse of the dishwasher, and flatly told that they werent going to do anything more on a machine. So far, out of warranty. Im sorry, but I cant accept that a machine under 3 years old should have 3 major failures. Maytag has to step up and at least look at this problem. From what Ive read, this is a common problem that has resulted in several fires. Maytag has to know about this and continues to do nothing, not even issue a recall on the current touch panel used. I am now faced with putting another $100 in (which puts me at about $350 total on a machine I paid almost $500 for) or just buy a new product. Rest assured I will never buy another Maytag-Whirlpool appliance.

We bought a new dishwasher 2 years ago. Top of the line Maytag Model #MDB8959SBW3 $749 plus tax. We bought this one because they told us what a great 10 year warranty it had. Found out that is a lie. The only thing the 10 year warranty covers is the stainless steel tub, the racks and chopper blade. The stop button on the control panel (circuit board) quit working and the dishwasher wouldnt start. When I called Maytag they said So sorry. It broke so soon, but that is not covered.We were told by a repair shop that Maytag has had nothing but problems with their control panel and the control panel part alone is $150 plus tax plus installation. Our old Maytag lasted 13 years and was still running great, but needed to be replaced because the racks were rusting out. I wish I would have kept the old one. I will never buy Maytag again since it is now made by Whirlpool. If Maytag is having so many problems with their control panel, they should be recalling them.

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

Purchased what was supposed to be a good dishwasher. In less than 3 years the control panel went out. It would cost more to replace the panel than to buy a new dishwasher. I will never buy another Maytag product.

Two in a row make it just over a year then the control panel goes out. You call a Maytag repairman and they say the control panel is bad! #1 it should last more than a year and a half. #2 a part shouldnt cost you as much as the darn dishwasher! Do not recommend nor would I ever buy another Maytag.

Dishwasher is around two-three years old and it will not start or drain. From what I can tell on the internet, this touch-pad control panel has been an ongoing problem for Maytag. Will try to fix myself, and if I cant fix it, I will buy a new dishwasher but not a Maytag. By the way, my washer and dryer both went out this year - five years old and both are Maytags. Stay away from this brand.

I purchased Maytag dishwasher (model # MDBH979AWW3) in June of 2010. Trouble started on washer after 18 months. Touch pad buttons dont all seem to be working. Occasionally gets to run after slamming door multiple times, but dispenser doesnt function properly. After trying to diagnose myself with door switches, connectors, etc., I caved in and called service. Service quoted $470 parts and labor to fix the problems, including control touch panel, dispenser, and control board (seems common from what I read here). Wish I had seen this string of posts before I called Maytag/Whirlpool customer service to see if they would help before I did any repairs. The responses I got from the service rep were rigid and scripted. Only time she varied from the script was to explain that modern high-efficiency appliances dont tend to last as long as ones 20 years ago. 18 months? Really? I might buy that if it was a mechanical durability design issue. Supervisors responses were also scripted, pointing back to the 12-month warranty. She said she did a warranty search on my model and that there was no warranty concern for this problem (really?). If there was, she might be able to help me. I guess there is no warranty history because most failures are between 12-24 months and the consumer has to pay for replacement outside of warranty. No semblance of customer service or customer care, just repeating what is on their website. Response was: I am sorry you are dissatisfied with the product and my response, but there is nothing I am authorized do. Sent an email to Maytag customer service regarding the problem and customer service interaction. They called back saying they stand by the original customer reps response, but offered to have someone else come out to give a second opinion on the problem. From what I read here, that doesnt seem necessary. Wish Maytag/Whirlpool would at least acknowledge that there is a problem, even the auto industry seems to have figured out a way to equip the service industry with known recurring problem history (TSB) and offer token help to keep customer loyalty. Apparently another quality organization fallen victim to short-sighted methods of maintaining shareholder value.

Just purchased a maytag dishwasher from home depot. I did the install myself. The dishwasher will not work at all the panel lights up, but no water goes into the washer. I now must wait two days for repair. After reading all the other reviews, I am thinking about returning it for another brand. And yes the water supply is on. I have hooked up several dishwashers. This is the first time a brand new one did not work right from the store.

I purchased a Maytag Centennial - HE Energy Star Washer from the local Home Depot on Guam.... Probably the worst clothes washer I ever purchased. I typically buy a Whirlpool brand for many of my appliances of which I have always been satisfied with the products. I understand that Whirlpool is now the new principal owners of Maytag. I bought the Maytag for my new second home which I have moved into as my primary residence. Great ads on TV that promote the Maytag product line but the product fails miserably in performance. From the day I purchased the washer, my wife, kids, and I visibly noticed the laundry doesnt get as clean as my previous washers, it takes longer to wash a load of laundry no matter what is the preferred setting, the irritating hum is deafening in my laundry room, now the washer has malfunctioned and doesnt cycle through properly, leaving the clothes either unwashed or wet... I do not know who is your servicing agent or center on Guam and I am debating to repair it or just dispose of it. I can tell you now... MAYTAG... NEVER AGAIN. Now I know why the Maytag Repairman is so lonely.... I wouldnt bother to repair it. I hope these issues do not filter down to your Whirlpool products. That Samsung is looking pretty attractive right now. I bought one of their dishwashers that is doing a pretty good job right now.... Guess what? There was a Maytag next to it that I didnt even look at.

This dishwasher was here when we bought our home. It has been heating up way too much on the drying cycle. I turn it off and air dry the dishes but today I noticed it melted my plastic measuring cup. I had the heat turned off and opened it as soon as it started the drying cycle.

I purchased a Maytag quiet series dishwasher (Model Number: MDB6759AWW) for $500.00 in May 2009. Three months later, I started experiencing difficulty with the control panel. One light would continue to blink and it would not do anything else. I called to have it repaired but by the time he was to come out, it started working again only to stop working again the next week. On 7 Oct 09, the repairman came out and replaced the panel. Then, about six months later, it stopped working again. I called again but canceled the appointment because it started working again. Then, after having it for one year, it stopped working again and I called only to be told that it was no longer under warranty. Now, we cant get the control panel to do anything. From all the other similar complaints I have read, it seems like there is a defect with the control panel. A dishwasher should last for more than one to two years. This is very frustrating.

After 1 year and a month, the dishwasher would not work. When the Maytag repairman came, he told me that this was the 3rd one this month that had the same problem (the control panel). The cost to replace, it would be about $275. However, since I know of 3 that have broken, why would I replace it? I live alone and maybe have used the dishwasher once a week. There should be a recall on this machine. I called to see if there was a recall and was told Im sorry. I would advise anyone purchasing a dishwasher to avoid Maytag or any dishwasher made by them.

Purchased Maytag dishwasher two years ago from Home Depot. It worked for about six months before it would stop working. When adding a dish after initial start would cause the unit to just die. After unplugging unit for a day the start/cancel drain buttons will flash. After reading online about a demo mode have tried and gotten it to work periodically. I continue to read online and have found there is a diagnostic mode. The settings are in a schematic packed with the unit. I found mine written in French (part #W10321879A). I called Maytag/Whirlpool and asked for the English version. They could not and would not provide me with part #W10321878A the English version, a single sheet of paper. They will only provide to a licensed repair technician. I am only asking for what should have been included in the original purchase. I paid $850 for a dishwasher that is not chump change. I know the control panel is bad but I would like to use it until the new part arrives. I think I may return the control panel and take my losses and go buy a brand that is not owned by Cesspool (Whirlpool).

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

Like many of the other complaints, control panel lights up but dishwasher will not start. It has had minimal use and is less than two years old. For a product purchased for around $800, it should have lasted far longer. Repairs will cost close to the cost of replacing entire unit. Do not buy Maytag. Their reputation is ruined in my eyes.

In December 2010, we purchased our Maytag Quiet Series dishwasher model #MDBM601AWB3, serial #NY2916421. At first the sanitize light quit working about 6 months ago. Today, September 30, 2012, this piece of crap will not turn on at all. There are no lights on at all. We paid almost $600.00. As far as being quiet, oh yes it is quiet alright! We the consumers are demanding a recall. Look at the complaints! Its a manufacturer defect in these control panels. I will not be forced into buying another dishwasher or a control panel. I want this company to stand up and say theyre sorry and fix this problem for all of us Americans!

Maytag MBD7749SB - We purchased this dishwasher for close to $800 at Home Depot. After close to 1 year we had to replace control panel. After another 5 months we have to replace control panel again, but product warranty is only 1 year. Now we have to either buy new warranty for ~$250 or replace control panel for same amount. Customer service: terrible. We will not buy product from Maytag again.

My husband and I purchased a new Maytag dishwasher in March of 2012 at a cost of around $650. There is only the two of us at home and I only run the dishwasher 2-3 times per week. On June 16th, I went to run the dishwasher and it would not turn on after hitting the start button. The cycle buttons lit up but the dishwasher would not start. I called the service number in the user instruction manual and talked to a service representative. I was told that the electronic panel that runs the dishwasher is not covered under the 2nd-10th year limited warranty. It would cost around $291 to fix including parts and labor. When I asked for a qualified Maytag repair service company in my area, she only had one company to give me. This company does not have a very good local reputation so I preferred not to use it. My question is - How can a part that runs the dishwasher not be covered under the warranty? If the start button on the control panel is defective then the machine will not work. I also have a model MDB7749AWW2. After reading some of the 356 complaints about this very dishwasher, I think the Maytag Company must be well aware that there is a problem with this machines control panel and they are choosing to disregard the customer. My old dishwasher was a Kenmore and it ran for 27 years and I only had to replace the motor once. I will not be buying anything Maytag in the future.

I bought my Maytag dishwasher in February 2011. It seemed like a good model - basic functions, upper spray arm, stainless interior. Well this dishwasher has been all downhill since I got it. First it is cheaply made. The racks and plastic stoppers on the racks immediately started falling apart. The one year after we installed it the front control panel went out, rendering the dishwasher completely useless! The warranty had just run out! To my pleasant surprise, I received an extended warranty offer from Sears. Had the front panel replaced and it started working again.... but apparently it is a bad design and it is likely to happen again. After reading online I am not the only one with this problem.Now another year later we are having a the sprayer on the top and the back hose replaced..... (still waiting for sears to install). It makes grinding sounds, leaves white marks, doesnt clean.... it is a non-stop battle with this product. Upon calling Maytag, they said they could give me advice but cant pay for any parts or even give me a coupon towards a new product! I have tried everything with this dishwasher - fancy soap, cleaning solutions, jet dry... its not me, its Maytag! I will likely be in the market to buy another dishwasher next year because of all the issues, and it for sure will not be a Maytag.

We purchased this brand new Maytag dishwasher (Model MDB7749) from Home Depot July 30, 2013. Now a little more than 18 months after purchase the control panel is out. Some lights blink, several go on at the same time. Tried resetting by removing then reinserting power plug (that worked once before, a couple of months ago,) but nothing works. Pretty much the same defect and problem I am seeing with other folks with these Maytag dishwashers. I saw online that a Sears outlet was selling these same model Maytag units for 48% off...Well, now I know why. My older Maytag appliances lasted many years. My Maytag washing machine was replaced two years ago, and it had lasted 14 years. I guess they simply do not build them like they used to. I should of just bought a cheaper model for 3-400 bucks, would of got the same use out of it. Does anybody know of a brand and model dishwasher today that is reasonably priced, dependable and has some longevity to it? I will call for service on this, but Im not spending hundreds of dollars on a defective engineering flaw, throwing good money after bad. Besides, the repair would probably only give me a 30-90 day warranty anyway. Learned my lesson. I will never buy another Maytag product again...Ever. Also I see now that they are part of Whirlpool, so they are out too. Anybody have any suggestions on a good replacement unit? Thanks...

Started having problems summer 2017. My dishwasher leaked and tank replaced, followed by drain pump, followed by circuit board in 2017. Didn’t have use of it for months. It has started leaking again as of Sept. 17.

Had this model MDB7749SBM1 for almost 3 years and paid over $700 for it. Thought I was purchasing a good machines. The last few months the control panel pops out and away from the front door panel. Do get it back. You have to unscrew the panel from the door. Inside is all plastic and broken. How can it be broken when it is an area never touched. Every time you open the door after a wash it pops out again. To get it repaired will cost too much. It is a badly designed unit which should have a latch instead of just pulling out.I am so disappointed and will think twice before buying Maytag. I have never had luck with any Maytag dishwasher lasting. At this point I dont know whether to just buy another brand or glue it. We are not keeping our home so I dont want to invest money. Awful machine and I see it is discontinued so there are a lot of complaints. Thanks for sticking us Maytag.

I bought a Maytag dishwasher in Sept. 2013. This dishwasher looks great, but it leaves glasses stained with a cloudy haze. It also does NOT dry, even on jet steam dry mode. Bottom line, after a little research, I was the one who bought it, so I took accountability and just rolled with it. Well, the control panel stopped working this week (wont light up). I called maytag and the lady told me they would cover a service call and parts even though its not under warranty. When the service company called me, they said maytag will NOT cover cost, totally contradicting what the Maytag lady told me. After reading these other posts, I wish I would have visited this site before I bought this headache of a machine. I will never buy Maytag again!

We purchased a Maytag dishwasher, Model #MDB7749, in the belief that it was a quality product. Many initial reviews were positive. Unfortunately, that decision was a mistake. The washer is only three years old and the control panel has failed. We are unable to select wash cycles. It defaults to Auto Clean/Heated Dry only. The washer has been lightly used.An online search found numerous complaints for control panel problems with this Maytag dishwasher. Please check ConsumerAffairs, Amazon, or Maytags own Facebook (Maytag was forced to create the Facebook page in 2010 under a mandate from the Consumer Product Safety Commission after a recall of dishwashers for fire hazards) before making any decision to buy a Maytag/Whirlpool appliance. It would also be wise to purchase an extended warranty.Our Whirlpool clothes washer failed after 5 years (bearings + controls). We cant afford to replace a major appliance every three to five years. The estimated cost to repair the dishwasher is $300 - $400. Maytag/Whirlpool customer service is indifferent to helping its customers. Its disappointing to see a made in America company produce such poor quality products and not support them.

The 2013 Maytag dishwasher panel broke 13 months after the purchase. After several phone calls and complaints they agreed to replace the panel at no charge. Since yesterday I have the same problem and need them to replace this washer. I am on a limited SS income and I am not in a position to purchase another washer after 3 yrs. My previous one lasted almost 15 yrs. This is totally unfair and I hope that Maytag replaces this entire machine, not just another repair. It will cost them a lot less to do that by either sending or having LOWES to replace this one. Thank you so much.Updated on 09/16/2016: Maytag is asking $300 to fix it and they will not replace it. So, by coincidence a friend of mine had the same problem and she did the following and I repeated these steps and now dishwasher is working. Turn off the switch or unplug, or turn off from the circuit box, your dishwasher. This cuts off electricity to the washer totally. Wait 30 seconds. Push the cancel button and hold on pressing it for 30 seconds (precisely, not less). Push then, the start button and hold on for 30 seconds again. Turn on the power and the cancel light will come on and let the cycle finish do not touch anything, until it is turned off and the light goes off by itself. Then, choose your selection for washing push start and see if it works. It did with mine and hers. Good luck and LADIES- YOU CAN DO IT, if this little old woman did it by herself.

I bought a Maytag dishwasher (model #MDBH979AWS3) from Home Depot on July 2010 and had it installed. After 2 weeks, I found water leaking into the basement. The installer said rubber gasket in water line de-laminated and caused leak under the dishwasher and flooded the floor to basement. Product defect and water damage covered by Maytag insurance. Now Feb 2012, about 1 1/2 years after buying, the touch panel controls dont work. I called Maytag regarding any control panel recall and they said no and its out of warranty. The advice given was that they can send out a serviceman for $269 to fix with parts, labor and one year warranty. It seems like planned obsolescence. Dont buy a Maytag.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

I purchased a Maytag dishwasher in 2010 model MDB6709AWW1. I only had it a year and the control panel went. They came out and replaced it and the guy told me that they were having a lot of the same problems. Now in 2015 it has gone again. It will run, but you cant change the settings. I took out the extended warranty on it and called 3 weeks ago and they sent out a local appliance repair company. This guy told me he had just come from another house with the same dishwasher with the same problem. He ordered the parts and I have been waiting 2 weeks. I called and the lady told me that they changed the part # and that they dont have any made yet and dont know when they will. WHAT!!! How can a company not have any parts made for their own dishwasher. I didnt buy the dishwasher when I bought all my other appliances, because there was a dishwasher here. It was gross and didnt work well. All my other appliances are Kenmore and I will stick with them. Have owned them for years and never had any problems.

Purchased a Maytag MDB4949SHZ dishwasher new from Home Depot in January 2018 as part of an extensive home remodel and addition. Did not move back in permanently until late June 2019, so the unit was not used at all until then. It quit working in January 2021 and our local (Sandpoint, ID) appliance repairman diagnosed a bad motor and pump assembly (the main functional component of the dishwasher). The unit was marketed as having a 10 year warranty and based on past experience with older Maytag appliances we purchased it. The fine print reveals that the 10 year warranty applies only to components that are unlikely to ever wear out or fail; all the rest are covered by a one year warranty. Part cost is over $200 and does not include installation. Maytag customer service (45+ minute hold to speak to a live human) of no help. No way are we throwing good money after bad to fix it. Lesson learned; just purchased a Bosch.

Works great, quiet, cleans better than the others in my opinion, have had many others and they never impressed me like this brand does! I think this one gives you your money's worth and you don't have to look no further for a dishwasher again, and is top quality and hardly breaks down as well.

I have a stainless steel dishwasher, model MDBH985AWS10. Its about 5 years old. The control panel works intermittently -- Ive replaced and ruled out the door latch -- now Ive got the problem narrowed down to either the control panel or the circuit board. Ive read about this diagnostic cycle I could run to try to help diagnose the problem. I emailed Maytag for the code and waited a week and didnt get a response.I called them today and they said they cant give me the code--they only give that to their technicians. My dishwasher is not brand new, but I paid good money for it, and Id prefer to not have to guess what to buy when Im trying to repair it. Each of these parts costs about $150. Im not sure what the policy is for other dishwasher manufacturers, but for the next washer I buy, Ill find a company that either 1) has more reliable products or 2) at least tries to help the customer repair his own equipment.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

I purchased Maytag Quiet Series 300 Dishwasher in 2006. About 3 years ago, I got a letter that a recall had been issued due to an electrical problem. A service repair person came out and replaced the electrical element in question. Next the dishwasher did not work and a repair had to return again. Today I have the same electrical problem and after waiting on line 12 minutes to talk to Maytags customer service, I was told it could cost me a couple of hundred dollars to repair my 7-year old dishwasher. In my last home, my Kitchenaid dishwasher lasted 20 years before needing to be replaced. My daughters Maytag dishwasher lasted on 12 years. What ever happened to Maytags lonely repairman? I now have to get a new dishwasher and worry about my $3000.00 kitchen floor getting damaged with the removal of old and install of new. Believe me, my new one will not be Maytag.

I purchased a Maytag dishwasher (Model No. MDB8949SBWO) in September of 2013. Within the first year (and under warranty) the control module failed. The dishwasher is now almost two years old and the second control module has failed. From other postings it is obvious that Maytag has a known defect in their control units. To replace control modules on an annual basis makes this an extremely expensive dishwasher to own.

Purchased a new Maytag dishwasher three years ago. After having it for one year the panel box no longer worked. Had to pay $300.00 to repair. Now half way through washing the dishes again no water will go into the machine. Only the first part of the cycle. I am sure it is going to be the panel box after reading other peoples problems with this machine. I will not pay to have it fixed this time. I will have to buy a new dishwasher. I will never purchase a Maytag product ever again. I have lived in my home for 40 years and never had a problem with any appliances. This would have been my third dishwasher in 40 years and as you can see it has not even lasted 4 years. I will inform my friends to stay away from Maytag.

I have had to replace the control panel on my Maytag Dishwasher 2 times in the last 4 years I have owned it. I diagnosed the problem using the serviceman repair manual which is located on the kick plate or lower plate for panel of your dishwasher. This is not one of the dishwashers that is listed on the recall list, but it is on the dishwashers list that Maytag suggested that you buy to replace your dishwasher that is on the recall list. Model number mdbh9898awb3.

We bought a Model MDB7749AWB2 dishwasher 3 years ago. The first year the panel went out one week after the warranty wore off. They replaced it then and now two years, here we go again. Dont replace the part. I am not ever buying another Maytag again.

I put a lot of thought into my new dishwasher and decided to go with what I thought was one of the best. At just over the 1 year mark the rinse aid stopped dispensing product. Now after another 6 months the controls are not working. Being a widow living alone on a limited budget, I am not putting hundreds of dollars into getting this piece of junk repaired. No more Maytag for me.

I own a Maytag MDB9150AWB dishwasher which isnt covered under current recalls. Yesterday, I heard a loud pop sound, and it stopped working (also popped the circuit breaker). After taking the door apart, we found burnt wires at the bottom of the door close to where they bend to go under the dishwasher.I called Maytag to find out if they would do anything, since this seemed like a defect in the materials used. They wont offer anything!

I bought a Maytag dishwasher MDB7749AWM1 in May of 2011. Yesterday, the on button would not work, so I called a serviceman out from Maytag. He said the whole panel needs to be replaced, parts and service will cost me $240.00. What a shame. 2 months out of warranty. I had two previous Maytag dishwashers, lasted for years with no problem. The newer models are junk, do not buy them! I can see by the other complaints that they had the same problem. They do not stand behind their product. I wonder how long the new panel will last? Im done with Maytag products!

About 9 yrs ago, we remodeled our house. And when it came to appliances, I was vehement we were going to go with Maytag because of their great name and reliability (We have 7 sons and needed reliable appliances). Boy, was I ever wrong?! We have gone through 2 Maytag dishwashers and countless repairs to the Maytag dryer. And our top of the line refrigerator has been a piece of junk!Of course, shortly after the year warranty was up, the flimsy pieces of plastic holding up the shelves started breaking off. The repairman, who came to replace the cooling coil on the refrigerator, said those shelf plugs couldnt be fixed. The whole front of all drawers have come off as well. He mentioned that Maytag was going bankrupt and started compromising on fit and finish. And he said that we just happened to purchase in that time frame. Now, we have a compressor that needs to be replaced for over $500! I have, in my garage, a Gibson freezer from my grandma that is 40 yrs old, and literally the most reliable appliance we have. Never have we made any repairs to it!I called Whirlpool (since they bought Maytag) to tell about my horrible experience with Maytag, and let them know we have to replace these appliances. I asked if there was anything they could/would do (discounts whatever) to redeem their name. I was told that they would not be able to help at all. So, I told them that I would not give Whirlpool anymore of my business and warn anyone I could, not to buy Maytag, Whirlpool or Amana. Isnt there any appliance company out there who cares about customer service, a good name and a reliable product?!

My Maytag dishwasher model MDB7749SBM2 was two months out of one year warranty and the Whirlpool control panel went out. We replaced it for 80.00. 3 months later same issue. We had that replaced for free. 4 months later same issue. We had to fight but got that replaced for free. Now 2 months later same problem. It cleaned wonderful when it worked. I will never buy another Maytag or Whirlpool. I used to buy nothing but Maytag. We threw it out tonight. Tired of a dishwasher that is only part time.

I purchased a Maytag dishwasher 15 months ago and was told the control panel is bad. It would cost me $120 to have someone look at it. I might as well buy a new one by the time the parts are added. I called Maytag and they said that there was nothing they could do for me since I was three months past my warranty. Meanwhile, I see all of these complaints about the same problem and Im wondering why there has not been a recall on this. What does it take for that to happen? I will never purchase a Maytag again! Their customer service leaves a lot to be desired. All they do is apologize like its programmed in their heads. This feels like a fraud!

Purchased our dishwasher 11 months ago from Lowes. Dishwasher has a 10 year warranty on racks and 2 other items. We are 2 adults in the household. Dishwasher is maybe used 4 times a week. Very light use! Circulation pump is bad which also took out the dishwasher solenoid. Im not going to fix because it if only lasts a year again that is a very expensive repair. Very disappointed in this made in the USA product. That was the reason I purchased it. Made in the USA. Come on Maytag. You can do better than this!

I moved into this house and the dishwasher came with it. For an appliance that is over 8 years old it works beautifully. It cleans my dishes well and doesnt leave residue on them. I ran it through a cleaning cycle recently and that has only improved its performance. I recommend dishwashers by Maytag because they last and perform well.

I bought a Maytag dishwasher in 9/2006. I was happy with it until 12/10 when it smoked and almost caught fire in the middle of the night! Luckily, I have a GFI circuit breaker and it shut the dishwasher off before it burned my house down. After researching on Google, I found out that my dishwasher had been recalled as a fire hazard, and I was never notified by Maytag. I called Maytag from my house phone and the automated system knew my name and address immediately just by me calling -- so they could have easily notified me but they chose not to.I ended up getting a voucher to purchase a new dishwasher (model: MDB7709AWB2). The one year warranty has literally just expired, and the Start/Resume, and the Cancel/Drain buttons no longer work. The replacement parts from Maytag cost $212.37, and that price does not include the price to get it installed from a service technician -- add on another $100-$200 depending on where you live. This is a known problem, and seems to repeat yearly! Another annoying thing about this dishwasher is the wheels on the racks. They dont glide easily and they constantly get off the track. I hate this dishwasher and I will never purchase another product from Maytag/Whirlpool/Jenn-Air again!

Maytag Dishwasher control panel is not working again! We have owned dishwasher for less than two years but needed repair twice. This time the warranty has expired. We will not have it repaired again. Its too expensive! We will never go with Maytag again.

If you are considering this product...RUN AS FAST AS YOU CAN!! This is the biggest piece of junk Ive ever owned!! I would be more than happy to take back my 20+ year old washer over this JUNK!! It is 2-2 1/2 years old tops. I cannot count how many times my husband has already had to repair this garbage!!! I will NEVER purchase another Maytag appliance! My stainless steel dishwasher isnt any better!!

We purchased a full house of Maytag appliances to support American Made (ourselves). It is very disappointing that our Maytag dishwasher Model # MBD 89595BW3 has completely quit functioning properly. All the lights came on and nothing worked after that. We contacted Maytag and was told to turn off the power and restart after 2 minutes which did absolutely nothing. No problem - try again. Again, nothing. The disappointment is compounded by the fact that this dishwasher is only 2 years 7 months old. It is too bad that an American Made product didnt last long enough to show any wear and tear. Investigation to repair resulted in cost prohibitive investment. So sorry Maytag, we gave it a shot. Moving on to a more reliable rated brand.

My Maytag MDB7609AWW2 dishwasher was purchased on 1/2010. Last month, the control board only worked on the right side of the panel and the dishwasher would not run. I called Maytag to see if this was a typical issue with the washer, which they denied. I ordered and replaced the control panel but this did not help. After reading all these posts, I do not think Maytag is being honest with their customers. Also, it looks like even if I am able to fix this issue, it is likely to repeat. I think I will cut my losses now and buy a different brand of dishwasher. I will never buy a Maytag again.

I do not know how long we have had the Maytag but, it has been a long time and has run without any problems. Still looks good and does the job! The features of the Maytag are: pots & pans, temperature sense, sani heat, light wash, regular wash, pots & pans prewash, quick wash, rinse & hold, delay start and heat, fan dry, heat or air. This dishwasher has always been plenty big enough for our family of four including guests. This Maytag had a choice of black or white front so, it fits in. My next dishwasher will probably be a Maytag!

Most every post about Maytag/Whirlpool dishwashers reads the same. Mine is no different. The control panel on my model MDB7749SBM1 has failed after about 16 months of use. Its a lose-lose situation for the consumer, as the cost of parts and labor for the repair equals or eclipses the replacement cost of a new unit.Another fine example of the degradation of an American brand, once known for quality and reliability. Dont be fooled by the branding. Buyer beware!

This dishwashers start button stopped working after 1 1/2 years. We did not buy the Extended service warranty. So we are responsible for the service call and the replacement of the control panel. Ridiculous. I called Maytag to file a complaint and they never returned my call. I will NEVER buy Maytag again. There are enough problems posted to know better. This company should be ashamed!!!

I always purchased Maytag products but no more. After 16 months of ownership of the MDB7749SAM1. For the last three weeks I have been washing my dishes by hand. This unit has so many defects that it should be recalled. Sick of buying parts!!!

We bought a maytag dishwasher three years ago. Approximately nine moths later the control panel went bad. They came and replaced it. Approximately six months later they came again and replaced it. Approximately a few months later it went bad again. I complained to Home Depot and they replaced the dishwasher. Too bad they would not change the brand. Guess what? Here we sit, not quite two years later and again the control panel went bad just past the warranty. The cost to repair almost $470.00. Paid $525.00 for the dishwasher in the first place. I regret ever leaving whirlpool. Our first very heavily used dishwasher (whirlpool) lasted 11 years no problems.

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

Like so many others, I now discover, we are having a ridiculously frustrating problem with our Maytag dishwasher, bought one and a half years ago. Last week, the control panel stopped working -- we press normal and a whole bunch of other lights come on; try to press other cleaning options and entirely different ones light up again. Sometimes we can get it, with luck, to quick wash or super clean and thus have our dishes cleaned (which the machine never did that effectively anyway); sometimes we cant. I havent called the company yet, but given what Ive read, Im unsure if it would do any good. Judging from all the similar comments, Maytag is clearly selling a radically inferior product and care nothing much about this. We will surely never, ever buy another one of their products.

On April 8, 2017 I was sitting in my Dining room with Dishwasher in the kitchen in cycle cleaning. All of a sudden I heard electrical sizzling and turned to see my Dishwasher was on fire. I got up and opened the door and my Husband shut off the circuit breaker for the Dishwasher. He raced to turn off water under sink and went to disconnect the dishwasher when all of a sudden hot water was shooting all over the place. I tried to catch in a bucket but it was so hot and shooting out hose fast. Kitchen and Dining room were then filled with water. He realized the turnoff under sink was installed at time of house built and cant be fixed without a lot of chopping up under cement.Well finally we cleaned up the mess with mop and towels and relieved neither one of us fell at our age. He unconnected the Dishwasher and secured outside. About 2010 there was a recall on this model Maytag. I reported it and a repair man came to change the cycle panel and said it would be fine, not. Yes almost 7 years later a fire occurred. Just glad we caught it in time without losing our lives or my house. Never, never again will I purchase a Maytag.

Weve got a 3 year old dishwasher thats stopped working. First some of the lights on the control panel wouldnt light up, now only one light will light up and it wont start at all. Maytag would be better served to stick with the older mechanical switches and settings if it cant manufacture reliable electronic control panels.

Dishwasher Control Panel MDB7749AWM2 - Purchased unit on 11/22/2011. June of 2014 my start button stopped working, and after searching online I guess I consider myself lucky. Spent 38 minutes on Maytag consumer service site speaking to a rep who walked me thru a reset that did not help and then explained that my machine was no longer under warranty and $149 for the service call and the cost of the part assuming it was a control panel would total over $250 on a machine I spent $500 on. I spoke to a supervisor who was only willing to sell me a control panel at 50% off and do it yourself, and while they claim there are no consumer issues with this part, they stated that the warranty on the part is only 90 days. I told them this was the last Maytag/Whirlpool/KitchenAid appliance I would purchase and they did not seem to care so I will be moving on to another dishwasher since I will not invest $250 in a fix of an item that they will only stand by for 90 days!

I bought my Maytag dishwasher MDB7749SBM0 three years ago. After it was in one month it already needed a service call. It needed a control panel. Out of the dishwasher 4 weeks because this happened over Thanksgiving. Two months later it stopped working and needed another service call. Technician was inexperienced and another one had to be called. Out of the dishwasher 3 weeks. At this time, and because of the expense of the machine, I purchased an extended warranty. This was control panel number two. Not long after, the heating element had to be replaced. Two weeks without the dishwasher. Now, my dishwasher stopped working again and it needs a new control panel. The technician is rude but did offer the information that the moisture ruins the control panels. IT IS A DISHWASHER!!! IT USES WATER!!! I only run the dishwasher twice per week so I cant imagine how poorly it would hold up if it was run more often. I am on my third week without the dishwasher because the part is on back-order! No one can tell us when it will be in. I bought a Maytag because I thought they had the appliance market under control. MY MISTAKE! I am very angry.

I purchased a dishwasher for $741 in December 2012. I called customer service department who told me that I should expect to pay since I did not buy the extended warranty. I thought by buying a high end appliance it would last 5 years without the control panel giving out ($300 cost with installation). Please DO NOT buy this brand!!!

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

Similar to dozens of others, we purchased a Maytag dishwasher from Home Depot in March 2011. Recently, it stopped working, dead - no lights, no action. Called Maytag and they referred me to a Maytag Repairman: Coastline Appliance Service of Huntington Beach, CA. The serviceman came out and spent 20 minutes, checked the door switch for continuity, and declared the control panel bad. How do you know its the control panel, I asked. Its my gut feel, based on experience, he said! He charged me $129 for the visit and said a new control panel would cost $380! After reading other posts online, I can only conclude that a new control panel (if that is, indeed, the problem) will also go bad in the next year or two. So, like so many others, were off to buy a new dishwasher - and we will never buy a Maytag or Whirlpool appliance again.

Purchased Maytag Dishwasher Model MDB7749SBW3 in April 2014 along with other Maytag appliances to go into our home in the Georgia Mountains. Purchased Maytag for 2 reasons: 1. American made 2. Reputation. Bottom line, after just 2 years the dishwasher has failed. I prewash by hand everything that goes in. First the normal cycle stopped working. Then lights on front panel would randomly turn on and dishwasher would turn on by itself, and run for hours. I suspect this could be a fire hazard. I have tried front panel resets, cycling power, etc. Nothing works... It is really sad that American products are third world. I will replace the board myself in hopes of getting another couple of years out of it. No more Maytag for me. Rest assured every time I see someone in Home Depot or Lowes, looking at Maytag appliances, I will go out of my way to warn them.

I purchased a Maytag dishwasher with a control panel in September of 2013. In August of 2014, the control panel died and did not allow me to run the washer. In March of 2015, the piece which was replaced died. When contacting Maytag, even when they did the repair the first time, said they were unable to cover the cost because it was now out of warranty. Ive seen several class action lawsuits around the product with Maytag. Do not buy a Maytag. It used to be a quality brand, but is now terrible.

Excellent dishwasher but door kinda flimsy. Front panel scratches too easy. Top rack needs to be stronger and a bigger bottom rack. Other than that running wise dishwasher is excellent. Its hard to beat Maytag. I think they just build cheap stuff around good motors.

Bought a Maytag dishwasher early July. Worked great for 3 months. Drain pump went out. Called customer service, 30 minutes to get a person. 1 week to get a service tech here. Even though we told them pump was out. Sent with no repair parts. So has to come back at our inconvenience, company policy, not service tech fault. Tried to complain on live chat. 30 minutes for them to get with me. Still no satisfaction. Would not recommend the product for the company itself. Sadly thought we upgraded.

I purchased a Maytag dishwasher (Model MDB7809AWWI) in Sept. of 2009. In 2010 and 2011, it had dead control panels. The first time, it was under warranty. The second time, it was not, and I purchased a costly service plan to have it repaired. Now, 2012, its dead a third time. Maytag tried to tell me that I could purchase another plan for $289. I informed them that for that cost, I can replace it with a dishwasher that doesnt require costly service plans and yearly repairs. They informed me that their parts only have a 30-day warranty. If theyre not willing to stand behind their products enough to admit that one is faulty, then Im not willing to stand behind them as a company.

2 weeks after my warranty is up, the control panel is shot. They used to make quality products and that is why I purchased a Maytag. I had before this a very cheap dishwasher from G.E. and it lasted 9 yrs. I cant believe it is already broken. Do not buy Maytag!!

I also am the unfortunate owner of a Maytag dishwasher Quiet Series 300. I bought it in April 2006. The control panel has been a problem since the first year of operation. Typically, one of the indicator lights would randomly go on and off during the machines off mode. At other times, the control panel would not operate. However, if I waited a few hours, it would dry out, enough and then would operate. Apparently, steam leaks into the control panel and causes it to be erratic. This has been a problem with this design for many years and the Maytag Corporation has not cared enough about its customers to correct the design flaw. I remember when the name Maytag indicated a top of the line product. Sadly, this is no longer the case. As a result, my loyalty to them has ceased.I probably will not buy another Maytag product again. Their standards have eroded.

Model MDB7749AWM2. Paid over $700.00. Figure I would get a good dishwasher so it would last and clean dishes. I was wrong. I replaced all new appliances for kitchen in house we had purchase 3 years ago. I replaced door switch 4 times, front door panel where screws go in broke off. Salesman at Lowe’s said Maytag was a good dishwasher. It is a stainless front and stainless inside. I have had cheaper models and never had problems with.

We purchased a high-end stainless steel interior/exterior unit in January 15. It is now July 15 and we have not been able to get any use out of it. Day 1 washer leaked. Full day off for service. Guy told us we were using the wrong soap. It leaked on the very next wash. Called again. They forgot to check the soap dispenser. Another service/day off. Leaked again! Another service call/day off. They replace the dispenser & seal. Now washer no longer leaks but the dishes are dirty and wet even days later. Another service call. Another new part. And now we are waiting for our 5th service call. We paid for a new unit and have a refurbished cobbled together piece of junk. Maytag stubbornly refuse to replace this unit.

3 months after we purchased our Maytag dishwasher in Jan 2014 (Sears) it broke. The service person told us that the ELECTRONIC CONTROL PANEL (START, CANCEL, WASH CYCLE SELECTIONS) was a common breakage issue and fixed it. It broke again around one year from our purchase date. Same issue, but kept working and not working. Finally we contacted Maytags customer service. Although courteous the only thing we were offered for this common Maytag issue was a $249.95 one year warranty for them to come and fix this recurring problem. I explained that we had already spent about $870 (including tax, delivery and installation) for our middle of the line dishwasher one and a half years ago and asked if they would consider either charging us for a smaller service call/repair or just do it because it seems to be a design and manufacturing issue. After one hour and no sympathy I had to pay the $249.95 to get a repair person out and be covered for one year from today. I dont trust the cheap quality and the lack of support for the product. THEY ARE OUT THERE TO SELL MORE INSURANCE AND CUSTOMER SERVICE DOESNT MATTER!

Maytag french door fridge model MFF2558VEW7. I bought this fridge about 3 years ago. Have had nothing but problems. First I had problems with the freezer frosting up, then I had the same problem of ice buildup in bottom of freezer. Now the freezer only gets cold enough to cool drinks and the fridge only gets to about 60 degrees. This is not the only Maytag appliance I have had problems with. I bought a dishwasher a few years ago that quit working just after the warranty ran out. Both bought from Home Depot. After reading other reviews, it seems that appliances bought from Home Depot have had problems too.

On May 23rd 2009, I bought a Maytag Dishwasher and paid $360 for it. Within the first year, the circuit board had to be replaced, then one year later, the same thing. On October 8th 2011, it appears that the same thing needs to be done. I spoke with the customer service and they will not pay for it. Clearly, this dishwasher has a history of being unreliable and should be covered or replaced. The internet is full of complaints against Maytag for this very same model. How is it that they have not reacted or invoked a recall? I had a similar incident two years earlier with a Whirlpool dishwasher; it turns out that they are the same company. I will never buy their product again!

We purchased a Maytag dishwasher in January of 2011. Two years later the entire machine stopped working. We had purchased the extended warranty and the control board and panel were replaced. Now two years later it happens again. Maytag/Whirlpool is of no help nor do they care. DO NOT purchase their product!! Multiple complaints and issues with faulty control panels and the cost to replace one is the same as buying a new dishwasher so they cant lose. I will never again own a Maytag or Whirlpool product.