Rather than go through all the things I dont like about this washer, just read all the complaints because that is my complaints also: bearings, not enough water in tub, clothes not getting cleaned. Just check out the lint filter and see the gray and dirty lint after a load and you will see it doesnt clean the clothes. Now, the motherboard is kaput! Cycles are all screwed up. Cost is $386 for motherboard plus labor and I will not put one more cent in this piece of crap.Listening to the salesman and consumer reports on the best washer to buy. All they are concerned with is energy savings and believe me when I say that all energy savings products are a joke because you give up operating ability for the sake of energy savings-- true of refrigerators and washers, dryers, furnaces and the like. I will be buying an agitator washing machine. The saving on water are not enough to give up clean clothes.

This range cooks evenly, producing satisfying results every time. It’s easy to use, simple to clean and serves me well daily. It has a double oven feature with a smaller oven on top which is not only convenient but energy-saving. The top features a cooktop which is easy to use and maintain. Never had a better cooking appliance!

I bought this dryer 3 years ago and the fuse has blown three times. The dryer gets really hot and blows a fuse. The entire back of the dryer is clean and free of lint, the hose on the back, and the ventilation pipe running out of the house are completely clear, but the dryer continues breaking down. The Whirlpool NC folks have been out here three times yet it has broken down once again. I should not have to purchase another dryer after only three years!

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

The machine had automatic fill which did not allow enough water to rinse the clothes properly. I had to run another cycle to rinse the clothes. The machine was also extremely loud. When I had a warranty repairman come out concerning these two item as it was brand new, I was told I should have researched better. I gave it away after 3 months.

It’s a front loader, very quiet, and uses less water. The clothes come out clean and less wrinkled if you take advantage of the settings. l like the extra rinse and the drawer underneath. The capacity is able to accommodate enough clothes so I only need to do a load of darks and a load of whites each week.

I purchased a 2011 Bravos top loader washer machine. Doing a minimal amount of laundry for 2 persons, the Bravos is in disrepair needing bearings and an inner and outer tub. I was told to purchase a prepaid service call for $350 that will cover repairs plus a mere 1 year additional warranty. The washer sounds like a jet plane, gives off fouls odors, has black tar like residue after each wash and clothes never smell clean. Maytag has no complaint process, except an online chat that tells you to buy the prepay. Maytag has dumped a lemon on consumers and arrogantly expects us to pay for their garbage. They are disrespectful, dishonest and greedy and dont deserve anyones hard earned money for their ill made products.

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

I bought my microwave in Nov of 2015. We began having problems in April 2017. When you cook or warm something up it gets hot. The light wont come on and the display continues to say open/close door. After about 4 hours of cool down time it may or may not restart. After contacting Maytag I was told I should have purchased the warranty. They also informed me that they do not have repairman in my area. We have just replaced all appliances with Maytag so now I am concerned they are all junk. We did buy warranties on the major appliances, but how will they repair with no repairman in my area. Maytag used to be the best appliances but after this experience and now I have a broken microwave after only a year and a half that they dont stand behind, I will never purchase any Maytag again. It also seems that this is not the only issue they are having with their microwaves. I have contacted my Lowes where we purchased and they even made a Maytag call with no results. Maybe the suppliers should stop promoting and selling their items. We replaced a 22 yr old Kenmore microwave that was still working thats why this is so heart breaking. Stand behind your products. No wonder you dont have repairman. They would never get a day off from repairing your junk.

I have a Maytag Neptune washing machine which had a mold problem on the rubber grommet. I have been trying to call Maytag to no avail. I researched and saw there was a class action suit for this very problem and I was never informed. The washer may pose a health hazard and I would like Maytag to do something about it.

We purchased this washer 8 months ago, and still do not have a working unit. From the very beginning of installing the new washer we had repeated F4 and E1 error codes. A technician was sent out three separate times and they replaced the ACU each time only to have the same error codes recur. This unfortunately took 5 months as each time the ACU part was on backorder. After 3 failed attempts they agreed to replace the washer with a new one. We were dumbfounded when the new unit arrived and we had the same F4 and E1 error codes! They have again replaced the ACU and still we have the same error codes! They are sending yet another ACU but we have little confidence this will work and we are at a painful 8 months with no washer.

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

I purchased a french door Maytag refrigerator in Dec. 2009. We have never had decent ice. Icemaker is in the door and the seal does not keep the ice cavity cold enough. After many, many service calls and a replacement refrigerator, I was told to dump the ice twice a week and get ice out of the dispenser all day long. Really? All day long? It is model #bmft2771web1. They will not take care of this problem. It is a defect but they will not take responsibility for it. I now have a problem with my Maytag double oven! The temp on the bottom oven is 25 to 50 degrees off. I am waiting for my dishwasher and microwave to be next. I will never buy another Maytag. Buyer beware. I have to buy my ice from 7-Eleven. Thats why I bought a $ 2,100 refrigerator, so I can get my ice elsewhere!

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

Our current dishwasher was already installed when we purchased this house. It is adequate, however, it does not do a great job with caked-on food. This means that the worst dishes need to be pre-cleaned.

I purchased a Maytag gas range about five years ago. After about two months, I noticed that the paint on the burner grates was flaking off. I called the company and they told me it was cosmetic. I have since bought two sets of replacement grates. I call the newest ones my dress grates, which I put on the stove when I am having company. I use the damaged ones for everyday cooking. Last year, the panel flashed. It locks constantly. And often, the door would not open, unless we pulled the stove away from the wall, unplugged it, and that cleared the computer. So, after months of unsuccessful door openings, the handle finally fell off completely. And the door locks whenever the oven is turned on. You have to finish your cooking, press cancel, and wait until the oven cools off, and then it will unlock. I have tried pushing aluminum foil into the latch hole on the door but have not been successful. Sometimes I just put a spoon in the door to keep it ajar while cooking. This cant be energy efficient. Of course, it is out of warranty. I saw a similar complaint about the burner grates. Also, the paint has chipped in several places on the cook top and the disks are all chipped. I am never ever going to buy a Maytag product. Oh, by the way, I called a repairman. I paid $65 for him to tell me that to replace the lock mechanism and the door handle, it would be $400. I can buy a new stove for that, but not a Maytag.

The Maytag Centennial (Model MVWC6ESWW1) washer was purchased in September 2009 and within 18 months no longer provided water at the temperature selected on the control panel. The problem started after we used a spin setting to remove water from a cycle that did not complete itself. Somehow selecting a spin cycle disturbed the water temperature control mechanism. We were advised by Sears to unplug and then reattach the electrical connection (similar to rebooting a computer), but this was not successful in water being delivered to the washer at the temperature indicated on the control panel. While there was minor damage to clothing and a waste of hot water before we realized what was happening, the real inconvenience is not being able to rely on the water temperature setting. Based upon reading comments on the internet (including Consumer Reports) concerning this washer, the public should be warned not to purchase this machine. Better still the machine needs to be recalled in order to protect the consumer.

Purchased 4-2010, used maybe once a week, it stopped working 11-2013. They sent someone out to replace the faulty recall, which the recall says there is an electrical wiring failure that can cause a fire, so they replaced part. It did nothing, the dishwasher still would not wash, just fill up with water and drain, but would never go into wash, so we call and argue. First girl said that recall has been known to burn out the control panel so we have to pay for a service person to come out and diagnose it, if that is it, they will pay to repair it. Then when he does diagnose it, we call back, the next person says no, the recall has nothing to do with the control panel, that it is just a bracket that holds up the heating element... REALLY. Well then the Consumer Protection Agency has the wrong info because I just looked on there and the recall says, Electrical failure with the heating element that is not related to a bracket, I can read and I am not stupid, so we were out the $50 service call, so we finally got them to agree and pay for the part, but we would have to pay to put it on...HHHHHH NO, I am not spending another dime on service calls, I could spend the same amount and go and get a scratch and dent dishwasher for the same or just a little more. We are calling back tomorrow to argue more with them, then I am emailing the local TV station that handles these kind of issues. MAYTAG is a piece of nothing, I will never buy this or anything with their name on it again....

I wrote earlier about my dishwasher needing to have an electronic board replaced again. So I called the helpful (I say that with sarcasm in my voice) 800 number. My dealer asked me to call for help with paying for the new part. After an hour and a half of being cut off and put on hold, I finally got through to a person that could take my request. The gentleman explained to me about why they would not stand behind their product which was only 3 1/2 years old, and a replacement part that lasted only 11 months. He expanded on his thought about how it was too old to fix and the part was more than 90 days old. I am out of my $1,100.00 with no help in sight. Totally upset with this company and how they will not stand behind a poorly made product!!!!

So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

Love my washing machine. It is so big I need a step stool to reach down to the bottom. It cleans my wash well and I have dirty clothes. I hang my clothes on the line outdoors. My clothes have never looked and smell so good.

This dishwasher works great with regular plates and glasses but not so well with my plastic bowls or cups. Im trying different detergents to see if it makes a difference on how clean the dishes are when done.

Maytag calls peeling paint a cosmetic issue. With a convection oven it could be a toxicity issue. Waiting for an answer to my question as the fan blows the peeling paint onto anything that is not covered. Dont put foil on the bottom as this compromises the paint due to design. Truly sorry to have purchased Maytag as this line is not the Maytag we grew up with! Old school ovens and products had the quality or workmanship to last.

March 31, 2013 a Maytag front loader washer series 2000 was purchased. In January an error code E4 and F3 kept stopping the washer. Service replaced some minor part, worked for a week. Then service replaced a circuit board - worked fine for a few months. About June of 2014 the codes came up again. This time Service wants 430.00 for a 700.00 dollar washer to fix a continuing issue. So I decided not to spend the money. I could buy another washer, different brand of course, and try and fix it myself. I removed the top and the bottom front covers. The 3 wires going into the circuit board that was replaced were loose, barely plugged in. The catch all at the very bottom right had derbies and coin in it, cleaned that out. Looked at the motherboard with a magnifying glass. It had no bad solders, cracks or burn marks, so I proceeded to run my hands around the entire drum inside... and in the back side where you can’t really see were some more loose wires.... tightened them. Now with the spin rpms you can understand how things shake loose, I always look for the common sense issues.... I am currently on my third wash load. It runs smoother and quieter than it did when it was first installed. Point is the Maytag service sucks and with only a year warranty from the manufacturer. What did I have to lose to try and fix it myself. I am sure this is happening with a lot of other people. The odds of a motherboard or a circuit board going bad in such a short time made no sense. So check all the wiring FIRST. Make sure everything is securely plugged in. I would not recommend anyone buy a Maytag or Whirlpool (owns Maytag) for their reliability or service.

I purchased a Maytag Dishwasher at $600. 6 months after installation, the control panel quit. Maytag sent a repairman and replaced the panel. 4 months later, the control panel quit again. The repair man told me that if it failed a third time, that Maytag would replace the dishwasher all together. The control panel quit again just a few days before the warranty expired. When the Maytag repairman came for the repair, he tried to convince me that it was not the control panel this time. He then replaced the control panel, but did not use the embedded electrical connectors. He literally cut the wires and wired it together by hand, wrapping everything in electrical tape. He said this was a different repair than the others and the three strikes and a full replacement rule didnt apply. I wasnt convinced and called Maytag to complain. I was promised a six month warranty extension, if I would accept the repairs. Two months later and the control panel has quit again. When I complained to Maytag, I was told that I had no six-month warranty extension and it had never been promised to me. They offered to send a repairman to diagnose the problem for $130. Needless to say, there will NEVER, and I repeat NEVER, be another Maytag appliance bought for my home.

I built my home and bought all Maytag appliances. The freezer and fridge knock on wood have been repair free. Replaced control panel on stove for 400.00$. Washer after 2nd repair had to replace 600.00$. Dryer repaired once 95.00$. Replaced dishwasher with a new Maytag. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. This is the 4th repair. I have paid for 2 repairs out of warranty. 380.00$ the last repair. I did request some help from Maytag. They said no... My dealer did only charge me for the parts.

We purchased a Maytag Bravos set in 2011. The dryer works great, but the washer not so much. Every load of darks comes out with soap scum all over. I use the HE detergent and most time use less than what the load should have. We have soft water and I also use softener. Ive also tried up to 3 extra rinse cycles and a smaller load size and still have soap scum all over. Im sure the light colored loads come out same, just cant see it. Needless to say, very, very upset with this washer. I, too, will never buy another Maytag product, nor will I recommend one. Had our yearly maintenance check the other day and the service man couldnt give me the reason its doing this. So, so disappointed in this product!!

We bought a Maytag dishwasher 4 years ago, we had to have it serviced a few months after purchase for the soap & rinse agent dispenser not working, then a few months after warranty was up the buttons on machine wouldnt work, the control panel failed so we had to pay for a new one and install it... Well last night exactly one year from the install of the new control panel I walked into my kitchen to find it full of smoke and the dishwasher pour out smoke, when my husband came home he took the door off and sure enough the control panel was burnt and melted! Very scary. It is a very good thing I was home and this is why I never leave appliances running if I am not home.

Here recently I got a bravos washer x series because it suppose to cut down water usage. Well that it did. Now going on 7 months of having it now its starting to act up like when the cycle is done it will lock again and repeat the cycle all over. I use the normal or powerwash cycle and here recently how its suppose to sense the load and then start spraying the clothes with water and detergent. Well not here. Lately it still senses and spins and then starts filling up like its on the bulky/sheet cycle but its on normal cycle and it doesnt fill all the way up - just 4 or 5 inches of water. So I dont know what is up with this piece of crap and why its acting this way. Other times it will work fine on the normal and the other cycles but now its just acting all crazy.

The control panel of my dishwasher is malfunctioning. I looked this up online and ran into a recall for the heating element. Sure enough, my dishwasher is effected. I asked why I was not contacted. First they made up a story as to not having my contact information. This is simply not true, as I purchased the dishwasher directly from Maytag. Three years ago there was another recall and the heating element caused another problem so Maytag replaced my dishwasher.If a heating element overheats, it seems to me that a short-term affect could be overheating the control panel, causing it to malfunction. I read through a few recent complains and would also like to inquire about having this issue looked into by the Consumer Affairs.

I have called numerous times and the satisfaction is out the window. The MOLD is so bad on the gasket that I can not get it off and it just keeps getting worse. My clothes smell musty even after they are washed. Really fed up... I have had different Maytags for at least 40 years and I will not purchase another one at this point. Apparently your customer service is as bad as some of your machines. My word of mouth is not good advertising for you.

This washer is awful. We had repair guy out within year one 3 times. Changed the door gasket because it was a known problem. That did not fix problems. We have to drain and clean out hard to reach filter monthly, socks get caught in drain filter constantly. Horrible, horrible, horrible. Hate it.

We purchased a Maytag Bravo in 2011. With only three adults in the house using it for regular clothes washing, we were surprised when we had to call a repairman and the charge was going to be over $500 to fix the transmission and clutch. We had the same problem as described in many of the other comments, i.e., door sensor would not work properly and machine would not spin. Not even worth it to fix. Word is that Maytag is made by Whirlpool and if this is true, it would explain the disappointment. We have replaced more Whirlpool appliances than I can count. Never again Maytag!

We purchased a Maytag Jet Clean Plus in August of 2013. Within 8 months the control panel stopped working. Though it was replaced by one of their technicians it now after 9 months is broke again. How can this be such a crappy product??? Over 800 dollars for a dishwasher to have to go out twice in less than 2 yrs is just wrong. The company needs to stand behind their products!!! I will never buy Maytag again and will advise anyone looking to not waste their money!!! VERY DISAPPOINTED!!!

I am not dissatisfied with hhgregg, but with Maytag products. I purchased the Maytag Centennial Top Load Washer and Maytag Centennial Dryer to match. I was a bit leery of the new energy star models that use he only type detergent, but decided that was the newest and greatest thing out, so how could it be wrong? For the past two months, I have been sooooo very disappointed in Maytag. Neither of these brand new machines are worthy of being considered brand new. The washer takes extremely too long to wash a normal load, too noisy, and has ruined several items of clothing, due to malfunctioning distribution of bleach, fabric softener released after clothes are through washing. There has also been several times that the load wash is complete and the clothes are not even wet (like they were never involved in a wash cycle). As for the dryer, you have to run it through two 40 minutes cycles to get the load of clothes completely dry, so much for energy-saving. This is my first complaint to anyone, but after reading several reviews on Maytags website, I am reassured I am not alone. There are hundreds of other dissatisfied consumers of this Maytag product. I will be writing a letter to Maytag, requesting a refund.

We have had this refrigerator (Maytag Side By Side Refrigerator with Ice Dispenser 27 CU) for 5 years this month and have already had to have it serviced once and now the ice dispenser just went out. I wish there was a brand out there that did not have problems and when problems occur, you do not get the runaround to get them fixed!

Bought a washer and dryer from Lowes in June of 2016. Have had service on the dryer 3X and washer 1X since. Two person household that uses product a couple times a week. Dryer drum stops rotating / temp control fails / buzzer doesnt work / motor freezes up / washer makes loud banging sound at the end of the cycle every time....sounds like someone is hitting it with a hammer....Today I want a local serviceman to replace the motor but Maytag insists that I have one of their reps come out next Tuesday to examine the product and then go from there. I have been on the phone for 45 minutes trying to get them to pay me $128 for the failed motor that I will send them for inspection. They will not cooperate. They are hiding behind some BS policy. I want to inform you all in case you are contemplating a Maytag purchase. I will not purchase nor will I recommend Maytag to anyone.

Why is it when you wash dark clothes they come out with white spots which looks like soap. I have put very little soap and it still appears. I usually wash in cold water so I tried warm water - same result. I have had a Maytag for a least 40 years never had this problem - what is it I am doing wrong? I have to wash and rinse at least 2 more times. I would appreciate a answer so I can fix this.

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

Purchased 4 Maytag kitchen appliances - stove, double oven, fridge, dishwasher - was told that they were all made in the USA. WRONG. The microwave comes from China - not sure why Maytag is not being honest. Not happy with my purchases - even though we spent $4000 to buy American. Warranty service is awful - even extended warranty is a joke. Would never purchase Maytag again.

The fridge has a grinding noise that is getting worse, by the day. I cannot seem to define the exact location of problem, whether the freezer or the fridge. Maytag you stink, and your web site stinks, too.

Do not buy a Maytag Washer. I had a Maytag for 25 yrs with only 1 repair in its 23rd yr. When it finally retired at age 25, we replaced it with another Maytag assuming it would also last long. No chance. We had only 2 good yrs. Now, at 2 yrs old, it is so so loud during the spin cycle that it sounds like an airplane (757) is flying overhead at 50 ft above the roof... No way can we possibly use the washer if anyone in the house is sleeping. Repairs cost more than the initial price of the washer. Please do yourself a huge favor and buy another brand. There are too many complaints about Maytag to even consider purchasing one. Not worth the aggravation!!

I love using my microwave because everytime I am in a hurry, like going to work and my kids to school and dont have time to cook or we dont like to eat outside fast food I cook healthy the night before and microwave it the next day and it just feels like the food is just made. It taste so good my kids and husband love it.

I have a Maytag refrigerator - the kind with the French doors with the freezer in the bottom and then the middle drawer is now leaking water all over my hardwood floors. This is ridiculous. Maytag better get off their butt. They need to send people out or send letters to people that have these freezers to fix them. When you pay a lot for something they should get a good product. If there a recall they should of send out letters or something.

Our first (and last) experience buying anything made by Whirlpool. I bought a matching Maytag Series 2000 washer and dryer in February 2011. By July, the washer was at 747 take-off noise level when hitting the spin cycle. I called Whirlpool, who directed me to their local repair firm. I called them on August 2nd and had a service rep visit on August 9th. He looked a 30-second look and advised that the bearing assembly was shot and that the spin basket required replacing.

I purchased a Maytag dishwasher in March 2005. About every 8 to 12 months since Ive owned it, the control panel malfunctions and needs to be replaced. I was told by the repairmen (similar to the many other postings below) that the malfunction is due to a faulty design where warm moisture shorts out the electronic control panel. For a few years, I paid for a service contract. But this seemed quite unfair, given the regularity of the same malfunction. Given that this is such a common problem, isnt there some responsibility by Maytag? This is clearly a faulty design. What about the legal responsibility for a recall? Is it possible that, together with other aggrieved owners, a lawsuit against Maytag would be the appropriate action?

Bought Bravos XL washer and dryer about 4 years ago at Home Depot. The dryer is fine. The washer not only doesnt clean the clothes unless you have it on rapid wash - but every person that is here when I wash clothes is shocked at the noise coming from it. I always say my laundry plane is landing or taking off. Its out of control.

Purchased refrigerator model # MFT2976AEMOO September 2013. First repair was 1 month after purchase. From compressor to moisture build up inside fridge. 7 repairs in the first year. Customer service disgusting. They simply dont care, and do not back their products. Work time lost waiting at home for repairs. Service men come and always have to order parts, which means 2 service calls for each problem. Our service man broke one of the drawers when removing it to do a repair which meant another visit for that replacement part. Continued to have more problems when warranty was done. Just replaced my 3 year old fridge. Could not afford to keep it any longer. Have never been more disappointed with any appliance that I have bought. Will never buy MAYTAG again. Product is inferior.

Purchased washer less than 2 years ago. Loud noise like a jet engine or helicopter in spin cycle. Did not purchase the extended warranty. Called Whirlpool/ Maytag customer service. Was told I could have one of their repair people come out. I would have to pay $300 which would give me the repair and extended 1 yr warranty, or I could get $300 off toward a purchase of a new washer. Are you kidding me? This washer wasnt even 2 yr old and making this horrid noise in the spin cycle. I had to have a independent repairman for Maytag washers come out to tell me it wash the bearing and would cost 3 to 4 hundred dollars to fix it. I said no thanks and after his $90 service call am stuck listening to this piece of junk make noise till it completely breaks. I will never buy a Whirlpool product again or recommend one. Whirlpool you sell nothing but junk.

Purchased the Maytag Bravos washer approx. 2.5 years ago. I cannot even begin to describe how disgusted I am with this washer. My clothes i.e. towels come out ripped on the edges, clothes do not get clean, shirts etc come out wrinkled no matter what setting used. It is not energy efficient because loads of laundry need to be washed twice if they are soiled (like our everyday jeans). Went back to the independent store where I purchased washer and was told to use only the bulky or gentle/delicates cycles to reduce rips in clothing. Such a complete waste of money, and it was not cheap!

Purchased a Maytag Dryer, Washer and Oven Range in December 2011. Both washer and oven were serviced within 1 year under warranty. The dryer stopped working in August 2013, not under warranty. Total cost to repair is $450. Called Maytag to see if they could reduce the repair cost, answer... NO. Maytag spends millions of dollars in advertising... Built Strong to Last Long but they cant spend several hundreds to keep customers. Will never buy a Maytag, Whirlpool, KitchenAid or any other related company product ever. Their motto should be Built Weak to Last Weeks.

We bought a Maytag Bravos XL assuming that because of the brand name it would be a great machine. WRONG. This washer is truly awful. Every single load of darks comes out covered in soap scum. I always have to rewash every dark load with no soap for a full normal cycle in order to get the scum off. My whites are probably also scummy but often I just throw them in the dryer as I cant see the scum. Its just a very, very poorly designed machine that obviously wasnt tested before they started manufacturing and selling it. Its criminal how Maytag continued to sell this piece of junk, and Ill never trust their brand again.

First off I dont usually spend my time writing complaints; however, I feel Maytag is deserving of my complaint. Purchased dishwasher Model #mdbh979sab1 in 2013 and days before the 1-year warranty was up the front control panel quit responding, rendering the appliance useless. Got that fixed under warranty. Now about 1 year later guess what... Its got the same problem. Began to read others post on this site and found that this is a common issue. One person posted that her dishwasher began to smoke and nearly caught her home on fire. Maytag was kind enough to offer a paid service call and enrollment into their extended warranty program. I think Ill cut the umbilical cord on this one and go get something more reliable and doesnt pose a potential fire hazard.

I purchased a Maytag MDB7749AWM model dishwasher in March of 2012 for approximately $600. Fifteen months later, the control panel has gone out on it. From what I understand, this problem happens so often that its not even worth repairing this dishwasher.

I have a two year old version of this dishwasher (MDB894995BB3) and now the start and cancel light on the control panel stopped working. I now see that this is a common theme with this model and I feel it is their obligation to repair these units with permanent fix and not the same thing that will fail again. I have 3 different Maytag appliances all bought 2 years ago from Home Depot and they are all broken. I will never buy a Maytag product again. I might replace this dishwasher as I know it will fail again. 2 years on a dishwasher is a complete failure. Unreliable Junk. Do not buy Maytag.

We bought this from our local big box retailer paying $433.87 after installation, the oven, haul away and home delivery. Two years and 3 months later its a boat anchor. Display is cold and dark after stating we needed to open and close the door before it would heat. We did but it kept displaying the same message. Unplugged it, turned circuit off per Maytag customer service line, still nothing. It is no longer made and you cant get parts. It is useless. The 10 year warranty just covers the magnet and the cavity.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

I purchased a Maytag Neptune Washer and Dryer at Home Depot for over $900. Within months, the board went out. The repairman said that they didnt even know how to fix it yet - no training. The board was out again. This time, it was not under warranty. The repair costs $779 including part and labor. There were numerous other little problems along the way that we did repair, but now, forget it.

Model MMV4205FZ3 microwave hood combination. No problems with open door signal yet. However, light over the stove burnt out. When removing, it exploded.No didnt unplug first. Previous microwave didnt have a problem with this. Instructions are useless. Didnt say to unplug and doesnt provide a model number for the bulb. Consequently, we have now purchased 5 different bulbs and they dont work. Tested socket and power is going to it. Rep at Ace Hardware said he had heard about this happening several times and provided what was to be the correct bulb -- didnt work.

I purchased the Bravos washer and dryer suite. Since I was a small child I had heard my parents and others alike say that Maytag always had superior products as this is the reason when I was fortunate enough to purchase a new set I chose a Maytag brand. We that was the past and the present products et washers /dryers as the worst ever. I have had my set less than 2 years and today had to go out and buy a used one again. I have had nothing but trouble with these 2 and will never buy their brand of anything again. From the amount of poor reviews it appears I am not alone. I tried several times to no avail to have someone from the company contact me as I was put on hold too many times!

Got the dryer free when we moved into our townhouse. We had been doing 2-3 loads a day for almost 8 years. The dryer was old when we got it. No complaints. Just wish there was some way to fix it. But mechanic said, No way. Almost a valued member of the family. Say 2 loads a day, 7 days a week, 52 days a year. This is a lot of loads. Remarkable. New machines cant do that today says our mechanic, they are not built to be fixed. Now, when broke, replace, don t fix.

Side by side refrigerator model #msd255oveu01. I bought this refrigerator Apr. 2011... The 1st year, the ice kept sticking in machine or freezing up. Now they have had to replace the modules 3 times. Once fall of 2012 and and again yesterday, 3/19/14 and they had to come back today to replace that one. I have called Maytag and they wont stand behind it since the warranty is over. I have told them that this is an ongoing thing with the ice maker and I have had to have it serviced ever since I have bought it. I told them from the git go that the ice maker needed replace. The ice dispenser also drops an ice cube on the floor on occasion and if I use crushed ice it jams up. This product is defective and is not a good product.

A little over two years and my Maytag dishwasher needs 300 to $450 in repair for circuit board or boards. The repairman said that they got cheap and left out a seal which allows moisture to get into the electronics, duh. They have a known problem but will not stand behind their screw-ups. Never again will I purchase Maytag, Whirlpool or any other product made by the bumbs.

The refrigerator works well. No problems. Easy to move to clean behind it. Good value. I havent had any problems since I bought it. Keeps a steady temp; Its exactly the size I needed; has plenty of space. Its a plain fridge with a reasonable price!

Refrigerator (Model Mff2558vems) purchased end of November 2011. Early in 2013 notice refrigerator first forming ice all over freezer, including an ice sheet on bottom of freezer. Then noticed water around refrigerator. Called maytag and they sent repairman even though a little over year and out of warranty. Their service people seemed to know exactly what was causing the leak as they came in with the correct replacement part. Worked fine however, there was damage to my newly refinished hardwood floors which Maytag did pay to repair. A couple of days ago I opened the freezer and again noticed ice all over freezer. The next day, water all around freezer. I cleaned everything up, so I thought. The day after, we noticed the hardwood in kitchen buckling up far from refrigerator and the laminate in dining room bubbling, even though there was no visible sign of water. Called Maytag repair company but they couldnt come out for a couple of days. Called another local repair service familiar with Maytag refrigerators and he couldnt find anything wrong with refrigerator even though he knows leaking caused by refrigerator. Called insurance co. and they sent over service master. Leak is definitely coming from refrigerator. They had to pull up hardwood floor, part of walls, the dining room. They now have five large fans going and a defroster to dry things up. This is upsetting, as my daughters wedding is next month, my husband is currently laid off and I dont need this kind of aggravation again. I love the french door idea, so roomy for my large family, but I am now afraid of this refrigerator. I dont want it but think it is ridiculous I have to shell out more money when the refrigerator is less than 3 years old. I talked with a higher level supervisor at Maytag and they are only willing to give a 100.00 rebate towards a new refrigerator since the refrigerator is out of warranty. This is ridiculous. I thought by buying American I was helping our economy but what I got in return is heartache and crappy merchandise. If there is a lawsuit in California against Maytag about these refrigerators I want to join. My friend in N. CA who bought her Maytag refrigerator the same time I did is also experiencing leaking. So frustrating.

Washer would stop right after it started. I googled the problem and found out it was a bad lock. These Bravo XL units were purchased in 2015. Called an appliance repair and they charged me $250 to replace the lock (service call was $98.00 and labor was $90). The repairman left and I started the washer. There was a loud sound coming from it. I called the repairman back and he said it was the gear case and basket. He said the basket was covered under the warranty but the gear case wasnt. Would be about $750 to fix....no way was I paying the cost of a new washer to fix this less than 4 yr old one. I called Maytag. They couldnt help me. I should have purchased an extended warranty they said. The cost to purchase the extended warranty is now $394.00 per year....please do not purchase a Maytag/Whirlpool appliance unless you like buying extended warranties.

In May of 2009, my husband and I bought a new Maytag refrigerator side-by-side, model MSD-2572VEW. The day we bought it, pieces started breaking. The shelves started cracking, and now they are completely falling apart. There are also cracks in the inside walls of the refrigerator. Every single door shelf, inside shelf and wall is falling apart. I have fixed the ice-maker myself several times. I am now going to design and build some new shelves so that we can get as much use out if it as possible before it is unusable. I am angry that a company can make such a horrible product and not have to take responsibility. If my employer ever provided a client anything but the best, we would all be out a job.

Purchase a Maytag washer in 2012 and less than 4 years later have to go shopping for a new washer. Purchased a Maytag because was under the impression that it was a good product and would last. Not true. The washer almost caught fire, just happen to be nearby when smoke started coming out from behind the washer, so I was able to turn off the machine and then unplug it and my husband smelt wires burning. If I hadnt been nearby we could have had a fire instead of smoke. I dont want to rain on anyone parade but I wont be recommending this product to anyone.

The Maytag Dishwasher Model MDBTT50AWW started having problems cleaning dishes after about 3 years. I usually had to clean them first before placing in the washer. About 6 months ago (5 years of owning), some of the control panel buttons stopped working. Finally, the Start button stopped. Replacement part and service is about $400 per local appliance repair shop. They recommended buying a new dishwasher. They stated that the touch control panels have reduced the life of dishwashers to about 5 to 7 years. However, I had seen testimonials on the web of dishwashers lasting on average 9 years - not Maytags. I will be avoiding Maytag for next purchase. I have seen too many complaints online about the control panels dying. I consider myself lucky as my panel died after 5 years while many reviews say theirs died right after the 1-year warranty.

Purchased a Maytag top load HE washer in November of 2011 & by Feb. of 2012, Maytag had to bring me a new one after a service call to fix lasted only one week. So at the end of Feb. 2012 they brought me a new Maytag Centennial HE Model# MVWC400XW3 & this one lasted till January of 2014, less than 2 years old & quit working. Had a service man come out to look at it & was told not only it would need a $400 repair but it was made by Samsung, but Maytag had their nameplate on it!! Called Maytag customer service line which took about 30 minutes of hold time to get through & was told, SORRY, LADY, we cant help you. Youre just out of $613 after less than 2 years of service & we WONT help you!! This company should be shut down, they are liars, frauds, cheaters, producers of poor quality products, uncaring, & sellers of the worst products on the US market & I hope the Consumer Affairs will see enough of these complaints about Maytag products & shut them down!!!

I would like to say that I purchased the Neptune washer & dryer for my parents back in 1998. Up to now, 23 May 2015, not once has either of the machines required service and have been functioning well for the past 17 years. This is a testament to the quality and workmanship that is Maytag. This week I have purchased the Maytag Maxima front loading washer & dryer for my home because of Maytags reputation.

I attempted over and over just to swap out washing machines. I originally purchased a washer and dryer because of a defect in the top load they delivered. They talked me in to the frontload Neptune instead. Within months I started having daily reactions to mold and to my disgust found out it was from my washing machine. I begged to switch back to the top load I originally ordered and the store would not let me and referred me to Maytag who sent me some tablets and would help me no further. Apparently, the Maytag repairman wasnt lonely anymore if a product had to be manufactured and ready for complaint calls. Well I used the product. I used vinegar and baking soda. I have used hot water and bleach. I have left the door open to dry...It is the most cared for item in our family and the one that makes me ill literally. I cannot afford to buy a different one and would be interested to know if my husband’s declining health issues have anything to do with our mold issue or if it is just depression...Anyway, I was very discouraged to find out that other people in other states had washing machines replaced, but why didnt I? I would be happy if they could buy back my old Maytag that I had prior to this Neptune, I am sure it is making someone very happy somewhere. Why couldnt they have respected my very true complaint? I was not trying to get something for nothing. I paid for something to keep us cleaner and free from allergens and instead wash my clothes in mold and have mold spores leaching into the air in my home. Please help.

Both work good. Washer could be a little lower and it has quit rinsing and I cannot use it. But it is 9 years old, I think for their age they were a good buy. I plan to get the washer repaired because have been satisfied with how clean it gets my clothes and it washes pretty quick. I got the large capacity and with a very large load the washer gets them clean. The dryer is very good. It is just as good on a large load as small, dries quick. I would buy this type washer and dryer again and would definitely recommend it to folks. I have been very happy with this washer and dryer. The paint is coming off the washer where you put detergent and fabric softener in and it has rusted out some but it is getting a little age on it so this is expected. I like it, I can throw my comforter in and it gets it clean and the large loads always come out great. I think anyone who bought the set would be very happy with it. It is also quiet which I like.

Just got a Bravos Maytag commercial washer. Washed two throw blankets and the washer has a see-through window on top, and I could see that the blankets didnt move on top. How are clothes supposed to get clean if they dont move? It also took an hour and a half for one load. What you are saving on water you are wasting on electricity. I personally dont like them for those reasons. I appreciate the company in my town (little known), they let me return and get the old agitator type with NO sensors. Just love the agitator, might wear on clothes a little more but at least I know theyre clean!

I purchased a Maytag range (YMER8875WS) on June 20, 2011. When I put my Christmas turkey in the oven, the rack fell! It seems the oven wall has gotten wider in the middle, so the rack doesnt stay in place. I have read several comments online about this, particularly relating to Kenmore ranges. This is a very common problem apparently caused by the oven liner bowing outwards.

Last August I bought the Maytag Bravos XL. I have had 3 repairmen try to fix my problems with it and they cannot. The problem is, they cant fix an appliance that isnt designed correctly! Without water, one cannot wash. Dont be mislead that the huge area inside can be used for large objects like sheets and comforters. This machine is MUCH harder on my sheets and comforters than my old machine with a center agitator. I have shredded rugs, holes in sheets, black lines on clothes and a chlorine dispenser that puts spots on everything. The detergent dispenser hardware is rusted as well. Folks if this machine was an automobile, IT WOULD BE RECALLED!

We purchased a front loading Maytag washer in January of 2011. We purchased an extended service plan in January of this year. I noticed a very loud noise and inappropriate operation during the spin cycle. I called the service plan, who contacted a repair service to come out and check my machine. I was told that there was a major problem that would be very expensive to fix and that the Assurant company would contact me in a few days. The company called and said that they would give me 75% of the value of the machine ($650) because fixing it was not economically feasible. I said that I did not want the money; I wanted the repair that I was guaranteed by my service contract. They referred me to the small print on the back of the sales letter. When I asked about any manufacturers warranty from Maytag (the washer was less than 2 years old), I was told that they had nothing to do with the manufacturer and I had to take that up with them. When I tried to call Maytag, they were decidedly unhelpful and referred me back to Assurant.There are several issues related to this event that I wish to complain about: 1) How dare a major company sell a thousand-dollar appliance that becomes unrepairable in less than 2 years and take no responsibility for the breakdown? There was obviously a defect in the machine that took over a year to show up (we are a household of 2 adults and did not overuse the machine). 2) How could a service contract issued under the Maytag name not be aware of parts covered by the manufacturer? 3) Should not the buyer of a service contract bearing the Maytag name be informed that it is not Maytag (the manufacturer) that is guaranteeing the product, but a third party?4) Should not the seller of a service contract be required to display the terms of the contract in a prominent place? The sales letter specifically states Repair or replace - If we cant repair your appliance due to a mechanical or or electrical breakdown, well replace it. The limits of coverage are in fact given in small print at the back of the letter and are on the contract, but this contradicts what is displayed prominently on the promotion letter. This is false advertising and should not be tolerated.

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

Oven failed after 2.5 years of normal use (1-2x / week). Apparently a relay failed (and burned out bake element). Contacted service & parts dept and learned that repair would cost $100 for service visit and $413 to replace the control board. Only the $80 bake element is covered by the limited warranty. Wonderful oven if your hobby is appliance repair. After 2.5 years, it now functions better as a toilet than an oven.

My fairly new Maytag dishwasher took a break and stopped working. No lights on the control panel although there was power to the appliance. First repair call, I needed a new computer board. Then when the part arrived and was replaced, no lights on the control panel! Fuse checked out ok and now waiting for a control panel replacement. Really??? Dependable Maytag? No way and never again to purchase from this company (Whirlpool).

Purchased a Maytag four door refrigerator and it leaks water all over the floor. Every few days I remove ice from the bottom of the freezer.

Model MDB7749SBM1, Complete FALSE ADVERTISEMENT and GARBAGE. Let me explain. Maytag clearly claims this dishwasher is stainless steel on the inside and out... FALSE, BOGUS CLAIM. Please check for yourself, tried a magnet to it everywhere and the magnet stuck everywhere. I have had this dishwasher for 15 months. The keypad frequently stuck. When I called Maytag, they told me if its usable, there is no defect. 15 months after purchase and 3 months after WARRANTY ran OUT on Thanksgiving Day with 25 guest. The keypad finally quit for good. I called the Friday afterward and was told no service for a week. I called and received local service but they told me it would need a keypad, which I waited to call on Monday since Maytag is closed on weekends how ironic. I was told they wont cover anything since a certified person didnt come out even though nothing was ever fixed and they blatantly lied to the consumer. Tried to sell me an extended service plan. I will NEVER BUY ANOTHER MAYTAG PRODUCT AS LONG AS I LIVE AND WHEN IM IN LOWES OR HOME DEPOT, I WILL TELL EVERYONE IN THERE SHOPPING THE SAME THING, DONT BUY MAYTAG IF YOU KNOW WHATS GOOD FOR YOU.

I was pleasantly surprised that this basic model would work so great! It really gets the dishes clean. It came with the house so I did not choose it and probably would not have bought it if I had to shop for it.

I purchased a Maytag Legacy Series Quiet Series 300 in early July 2010. It had a recall for a heater part that could potentially burn down my house, so we couldnt use it while we waited for that part to be replaced. They offered me a small sum of money towards the purchase of a much more expensive dishwasher which I declined since Id only had the dishwasher a few months at the most. It is now the end of August 2011, a month past their factory warranty. The dishwasher did not get my dishes clean, made awful grinding noises and three days ago, it refused to drain and then spewed 50 or more gallons of water all over my kitchen which then leaked into the basement. The repairman charged $85 to tell me that the computer in the control panel had burned out and was not fixable. I think I paid somewhere in the region of $500 for this machine. My last dishwasher lasted about ten years. This is completely unacceptable. In searching the internet, I found hundreds, if not thousands of identical complaints. Clearly, this machine is a lemon and Maytag should be forced to replace it or better yet, refund the money spent to purchase the machine. Plus, pay for my valuable time spent mopping up water, washing dishes by hand, searching the internet for probable cause and potential solutions, waiting for Maytag/Home Depot to respond to my inquiries and a large sum for general annoyance. Maytag had a reputation of reliability (emphasis on had). Theyve got some slick ads but they do not stand behind their products at all. I will never by another Maytag product and I urge you to do the same.

My 6 year old Maytag 3000 series front load w/d set started leaking after 2 years. Minor leak on certain wash settings such as Rapid Wash setting that worsened (and I could live with), so that setting wasnt used. Last month the washer door was flapping open DURING a spin cycle. I stopped machine only to find the entire barrel had dropped and metal wire wrapped around clothing. Worst washer ever!

A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

The dishwasher turns on of its own accord. Sometimes when you get too close to it, once in a while in the middle of the night, and most of the time when you latch the door. It does a great job cleaning the dishes, but to no avail because its always in the middle of a cycle when you need them.

Magtag Bravos Washer top load Model MVWX700XW1 - I purchased my washer in June 2011 with the understanding that this was the best washer for my money and needs. I have family of 4, and laundry is a continual cycle at our home. I had the washer delivered and installed by the store where it was purchased. I was pleased with the machine even though the clothes were extremely wrinkled after each cycle, but the salesman was kind enough to tell me this would be so. 21 months into use, I had a water leak from the internal cold water valve. It’s not covered by warranty; I had the valve replaced. Within 2 weeks, the machine would not spin out the clothes; if it did, they were still wet, or would stop mid-spin cycle and start rinsing again. It took 2 hours to wash a 37 minute hand washables load this past Saturday, 4/6/2013, not to mention the other 4 hours washing to regular loads just to get the machine to rinse and spin. The service technician has spent the past 2 days at my home trying to repair my machine to tell me today that it is not the lid lock, but the master control panel which is still not covered under the manufacturer’s warranty. To say the least, I now have to purchase a new washer as I have invested $250.00 for a valve and the control panel is $275.55 plus labor.This machine is the biggest waste of money that I have ever spent. I have been a loyal Whirlpool customer having owned two other Whirlpool machines, each lasting 17-18 years each. I do not abuse my appliances, overload or in any other manner try to destroy a machine for personal gain. I do, however, feel that Whirlpool/Maytag needs to recall these washers or cover the parts beyond what is written. I have read numerous accounts of these and similar issues by others, yet the company will not stand behind their appliances. Really!

Maytag Washer over 3 years old. Often problematic not functioning smoothly! Maytag invented this defective machine to intentionally rob the customer with all the probs that comes with it - poor design & quality, & not logistically programmed! Even aftercare/customer service SUCKS!!! Now, sensor spinning option is no longer working, drum not operational. No more Maytag!!!

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

The control panel of our Maytag dishwasher stopped working when it was approximately 14 months old. We repaired it ourselves by following a reset directions we found online (push rinse button 5 times and then the cancel button twice). Also we cut the power to reset. Im not sure which of those two tasks reset it, but it worked until last week - now 28 months old. We are not able to reset the panel using any information that we can find. In trying to find repair options, we discover that there are a lot of complaints about the Maytag dishwashers control panels not working within just a couple of years. In speaking with Maytag, they tell me theres a class action law suit for this problem - meaning they do realize there is an obvious problem with their control panels, but are not acknowledging they have any responsibility to repair it. The law suit only covers the cost of the part but not the labor. The labor can cost between $100 - at the lowest - and up. Our Maytag dishwasher model # is MDB8949SAM1. Also noteworthy, our Maytag clothes washer gave out at less than 5 years. Maytag is no longer the company we all thought they were. Additionally, their faulty machines are costing their customers a lot of extra money. Not exactly what I would call a company with good customer service or even any ethics. We will never buy Maytag again.

I purchased my Maytag double oven (MEW6627DDB) in November 2008. In January 2013, with a setting on 375, it heated to 440 in 15 minutes. The repairman said $650 because it needs a new control panel and 2 new sensors, one for each oven. I contacted Maytag as I felt this oven should not have gone out in 4 years. I spoke with Ebony and then a supervisor, Vana. Basically, I was told that since I didnt purchase an extended warranty, there was nothing they could do. While I have a freezer 40 years old and still going strong, I realize that appliances manufactured many years ago were much more reliable. I feel that Maytag should stand behind their products and should have offered to send me replacement parts. I know I would have had to pay labor for installation. Their answer was I should have purchased the extended warranty. However, one should not have to purchase extended warranties for products. I had every confidence in Maytag. Why else would I have purchased my first Maytag product? I should have stuck with Whirlpool, which I was recently told, now owns Maytag. Maytag customer service personnel were extremely unhelpful. I wonder how many Maytag employees purchase extended warranties for their appliances or if theyre smart enough not to buy Maytag.

Maytag Bravos 300 Quiet series - Ive owned this washer for about three years. On average, I do 2-3 loads of laundry per week. I follow the loading directions, but still have to babysit the machine because of uneven load issues better than 50% of the time. Many times, clothes come out full of lint, even after running the clean washer cycle. This is the worst washer I have ever owned. Ive had better results from second-hand machines.I havent bothered to contact Maytag because Ive had it so long. Im almost to the point of getting rid of it and buying one that gets my clothes clean and isnt inclined to push the clothes all to one side and put the machine off-balance. To say Im disappointed in the product would be an understatement, especially since I paid $800 for it.

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

The Bravos XL MCT Maytag commercial Technology is not a good machine. I noticed it within the first few weeks. I called Conns to request technical support but the technician they sent didnt solve the problem. I also called Maytag, they also sent a technician. He told me the same thing as the other guy. To use good quality detergent and to make sure the clothes are neatly arrange around the drums walls. Nothing works. My clothes dont get clean because they dont get wet. Theres lots of residuals and wrinkles all over them. Also, the machine takes way too long to finish a load of clothes. I did tried to return it, but Conns wouldnt take it back. I dont recommend this washing machine at all!

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

I have a top load commercial tech washer with an agitator that is brand new as of September 2019. I have done all of the troubleshooting suggestions and nothing works. I use 1 tsp of liquid cold water detergent, deep fill, extra rinse, and clear liquid oxi and my darks still come out with white stains. I have had a Maytag tech check out the machine and it checks out without issues. I would never recommend this product to anyone!

This was purchased 3/25/2010 with the Home Depot Service Contract thru 3/2015 . We have already had a service call in 2013. We were OK until January 2015. Now we join many other customers with the leaking defroster. We have taken all the steps of the other customers. We went and called for a service appointment. Weve spoken to Maytag Customer Service 800-253-1301. Ive asked if there was recall? NO! I asked if there was log made of my call, NO! Any work done had to with Maytag Authorized Repair Person. The Home Depot Contract use a Non-Authorized Service Person. Weve gone to Home Depot. We are in a catch 22! We have spent good money on this refrigerator. Out of sight, out of mind. We will go back to Home Depot Again!