I love this washer. You can fill all the way or energy setting but either way it does the job. I paid 1200 for a Whirlpool. it was broken within 6 moand couldnt get service repair. With the Maytag it was on sale for 550 cash. It stop spinning. I called for service. They were there in 2 days on time and 20 minutes it was working. It was a needle stopped it. Just reprogrammed and wa-lah!

We purchased our Maytag dishwasher less than a year ago and are very disappointed with the poorly designed quality of this product. We had a Maytag repairman look at our dishwasher and he told us that; the dishwasher cleans with enzymes in the dishwasher not water pressure, and we need to make sure the water in the kitchen faucet need to be hot before starting the dishwasher, we also need detergent, rinse aid, and citric acid added to each load. Adding all these products to the dishwasher does not fix a poorly designed product. This product does not clean the dishes, even with rinse aid the glasses come out cloudy. The dishwasher has a power blast button, it does not clean the dishes any better than the regular setting and it runs for four hours. We will never buy another Maytag product.

I purchased both a Maytag Neptune washer and dryer in 2007. This is without a doubt one of the biggest mistake I have made. I have had the dryer drum and rollers replaced and the washer will no longer run. It is going to cost me hundreds of dollars to repair. To think I bought these units for 2 reasons: 1. that Maytag are the dependability people, but its not! and 2. Energy efficiency. It is not too efficient when they are broken more than they work. The worst was when the repairman told me that I had purchased the worst product on the market. These units are in short, garbage! I will never buy another Maytag Product!

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

I am having the same problem with the sheet of ice forming on the bottom of the freezer and leaking water out every week or so. It is getting very frustrating. After reading all these reviews I am realizing it is a manufacturing flaw and think there should be a recall. We have model MF12269VEQ3.

I bought a Neptune washer and a dryer. I have had nothing but problems with these items since I got them. My washer keeps giving me a 3e code and will not clean the laundry right. I have used the H E detergent it requires and yet my clothes stink. My laundry smells like mold and mildew. I now dont have my units to wash and dry clothes. I paid almost $4,000.00 for the pair. I dont have the money now to replace them.

I purchased my oven in May of 2012. Ive tried numerous times to use the clean cycle. There is absolutely no way it works. I contacted Maytag on 1/13/14 and their response was to explain the concept of AquaLift Technology as if I didnt already know that. They said I should use the plastic spatula (as if I had not already done that). They urged me to email whenever the need arises (as if that will do any good, they obviously acted like there was nothing wrong with their AquaLift technology). Someone should hold them accountable for their faulty product. Maytag is now a dirty word in this consumers vocabulary, and no amount of scraping ...with a plastic spatula will clean up the mess they sold me. I hope it breaks so I can go buy a product from a company where self-clean does not mean I am scrubbing (with no success) and running a clean cycle numerous times in an afternoon to try and get a spillover cleaned up.

After having had Maytag Highlander washer and dryer for 28 years in our early married life, and continuing to think that Maytag was a quality product, we purchased the Neptune front load washer MAH6700AWW. Let me tell you this IS NOT your mothers washer, nor is this Maytag a quality product. First it was necessary to install water pipe shock arrestors because of the water valve on washer causing shock in the waterline when it closed. The automatic Softener/detergent dispenser didnt work from day one.Coins and etc. constantly kept getting under flippers and couldnt be easily removed. I found that it was impossible to remove the plastic flipper without breaking a plastic mounting tab. On my first call to customer the Maytag Customer Loyalty Team, aka Customer Service (CS), I was told that the plastic flippers were not available as a separate part, and that the entire tub assembly with plastic flippers would need to be replaced. WHAT???????? THATS LUDICROUS. After temporarily securing the broken flipper to the tub, I thought Id call again about a week later to see if the previous answer was correct. On this call, the customer service lady (whose name I have), said the flippers are available and that she would send two at no charge. A few days later two flippers arrived, but were not the correct ones. I then decided to drill two holes in the tub and remounted the broken flipper with two stainless screws as a permanent solution.Two pumps needed to be replaced. One was replaced under warranty and one by myself. The one replaced by me was damaged by a coin that made its way from the tub to the pump. Other washer manufacturers provide a means of trapping such objects before they get to the pump. The wash cycle stopped unexpectedly numerous times without reason, after which the code 5d was displayed. I called Maytag Customer service. The representative didnt know what 5d code meant. Her suggestion was to call a service man. Again, I called later to ask and was told 5d meant excessive suds which wasnt the cause. Might this have been a control problem?There were three incidents of water discharging onto the floor from under the washer over the last two months, which caused water to cover an area of approximately 5 by 12 resulting in extensive cleanup in addition to damage to stored items. Since these occurrences were weeks apart and unpredictable, I knew the problem would be difficult, if not impossible, to diagnose, even by a serviceman. I concluded that it was probably a problem with the control; either filling too long or not emptying the tub before refilling for the next cycle. Thats when I decided to send this troublesome Maytag piece of junk to the landfill.

We have already replaced the motherboard and now it is throwing a code of and it takes a whole day to keep pressing start to get one load down. I hate these machines and tell everyone NOT to buy one. They are expensive to buy and too much trouble to fix or repair and too much money to fix. BUYER BEWARE!!!!

I have had this refrigerator for three years and have ALREADY had two major repairs! I have paid ONE THIRD of the original cost in repairs. The latest was a control board at a cost of $225 and the repair man only charged me a service call and not labor because I was so upset. I called Maytag hoping they would at least pay for the part, but they only want to sell you a service contract (Of course it wont cover the control board, that already happened but would be happy to sell you a new extend warranty). I WILL NEVER BUY A MAYTAG APPLIANCE AGAIN! Run as fast as you can away from this brand. Be warned. They will not stand behind their appliances!

Purchased a Maytag range with Aqualift technology in 2013 thinking it was a good brand and *happy* to find a new way to self-clean my oven. This turns out to be nothing but a joke and I am not *happy* with it. After following directions to the letter, there is some loosening of anything on the floor of the oven, but the sides and top are slowly being coated with more and more grease. Ive spent way too much time with my head in the oven trying to scrub stuff without using a heavy duty cleaner but feel I now need to resort to Easy Off as there is no other way to get it clean. I also dont understand why they tell you to remove the racks since there obviously isnt enough going on to even clean the oven... How would the racks be damaged? And now I believe there is a problem with the Dual Choice element where Im not able to turn the temperature down. Even turned back to the low setting, the pan cooks away like its on high. I have to keep turning it off and then back on in an attempt to find something similar to medium or low heat. Im so very disappointed in Maytag and feel this method of oven cleaning should never have been put on the market. Its a scam!

I purchased this relatively expensive range and could not have imagined how dissatisfied I would be. The Aqualift cleaning technology does not work. There is no way to clean the oven door. They stress not to use oven cleaner, but as the Aqualift system does nothing to clean the oven door, there is no choice but to use oven cleaner, which they say will ruin the oven coating. Also, the grates are very heavy and it is impractical to clean the range top. I wish I had researched further; this product is a MAJOR disappointment.

We purchased a home one year ago. It has all Maytag appliances that were anywhere from one year old to two years old. The Neptune LE washer is not working as of today. This washer is supposed to be the top of the line, and because it is almost three years old, it is no longer under warranty. This washer will fill with water but does not spin or rinse the clothes. We paid a lot for this home and were so happy to get appliances that were all practically new. Now, we refused to have a repairman come and charge us lots of money to fix a washer that should not be broken. I have had washers run for 15 years and that was when I was washing clothes for 6 people, including cloth diapers for triplets! I will not buy any Maytag appliances. I will be getting an Amana or a Sears brand. Please, no one go buy a Maytag appliance.

I love my gas stove. Mine is a five burner in white. Easy to clean and an accurate baking oven. Keeping the burner area clean IS a constant chore with a white surface. It would be lovely if the company made liners to catch the mess, but alas, I make my own with aluminum foil. This is an excellent stove and I’d buy it again! No buyers remorse.

I bought a Maytag washer 3 years ago. Maytag gave me a number for one of their warranty service repair shops in my area. The first repair service doesnt even respond to my calls. The second repair service is a total ripoff. So in summary, Im stuck with a 3 year old washer that has a broken drive assembly that the warranty wont cover.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

Unbeknownst to us, our Maytag Refrigerators (MFD2561KES) ice maker developed a problem with the fill hose which connects to the back of the refrigerator, causing it to pop off. The hose had been leaking water onto our wood floor causing all of the boards under the refrigerator and 6 feet in front to buckle. I cannot see why Maytag did not use a compression fitting instead of using a squeeze type hose clamp. Plus the ice maker has left a large sheet inside the freezer on the bottom. I use the ice maker daily to fill my cooler for work.We also have a Maytag Dishwasher which has a push button panel in front which has decided to give out as well. Not to mention our Maytag Double Oven which has never been able to close properly since we have had it. (The service man said that there is nothing wrong with it). We bought our house 7 years ago and my wife wanted nothing but Maytag because of our experience in the past. I gave up buying american automobiles years ago and I guess the same will happen when I replace these appliances (after I finish paying for my new floor).

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

Purchased a Maytag MSD2553WEW00 refrigerator on 2/27/2011 from Home Depot. Began using it in July 2012 upon completion of home construction. In February 2014, after less than two years of service, the refrigerator was running but no longer cooling. After the expense of several part replacements and a service call, it was determined that the compressor had failed. Unlike most manufacturers, Maytag did not warrant the compressor and closed system beyond 12 months. The refrigerator looks like new but the cost of repair is prohibitive relative to purchasing another new refrigerator. Maytag was contacted but was not helpful.

This is a review of a washer that is no longer sold. I bought a top of the line Maytag washer 45 years ago. After around 25 years the control (all mechanical) started sticking during the cycle. I opened it up, sprayed it with TV Tuner cleaner, worked it a few times, and it has worked perfectly ever since. That is the only problem or repair on that machine since it was purchased!

I have been washing clothes in different washers for almost 4 decades and never had a terrible washer until now. It has total control of the water level and it NEVER has enough water added. I have to add at least 2 full dish pans of water to every load. My washer does not allow you to pick your level because it does it automatically and no theres way to bypass this problem. It moans and groans for almost an hour in slow motion at its best. It should be illegal to sell such crap!If the intent was to save energy it fails when it runs twice as long as other washers. The instructions that are in the lid say that when you set it on deep water wash that it does not sense automatically-LIES! This lid must be generically made for other washers that they have because again, you cannot choose a water level. When a washer runs for almost an hour (this is not soak or extra rinse either) it is not saving energy over those that run for half that length of time. I wish I had returned it, but I listen to others who say that this is how washers are now. I still owe 150.00 on it and hate writing that check.

Bought a Maytag 4000 series washer and dryer combo for about 2100 dollars in October 2011. Had a professional look at it today since the clothes stayed wet after the spin cycle. Told us it would cost 1000 dollars to repair the washing machine. So a total write-off in barely four years. I am very disappointed.

Worst washing machine!!! I purchased the top loader Maytag Bravos washer HE in 2011 and they are the worst!!! It has been repaired three times already and now is making such a loud noise and I have been told it is the bearings. I did purchase the extended warranty and it expired. The reason I did not get a renewal is Maytag & Home Depot do not allow the the extended warranty company to let you know the warranty is ending. So now I have a 3 1/2 year old washer that needs bearings and will cost $500 + for repairs. Will not be spending anymore money on this absolute piece of junk. I had a Maytag that was 22 years old that I replaced and thought I was buying the same quality but never again another Maytag. This company may want to employ only repairmen because you will need only them because no one should buy a new one going forward.

I purchased a Maytag commercial residential washer in late 2018, supposed to have a warranty for at least 5 years. We are in California and I was told that there was only one facility that could come two weeks later. I removed the front panel to have it ready for service tech, who on the first visit kept saying he did not know what the problem was, and left telling me he would order parts. After Christmas, I could not get in touch with service so again called Maytag. Service was supposed to come out on the 30th.After waiting almost 3 hours, he called to tell me he did not have the parts. Also, this repair tech treated me very bad since I removed the front panel which I thought I was being nice. He called me back on the 30th, said someone gave him a part, and came. All he did was remove control panel, lost the start button and told me it worked without checking it at all. He was rushing to another appointment so I tried to start it and it still had the original issue, which was slow agitator and a rubbing/grinding sound. Now, after he did something with control panel it had a clicking sound. I immediately called corporate and was told when he came back, which has now been over a month with no washer, that he would be with a senior technician.January 5th I waited all afternoon and he called and said he was not coming and that my whole washer would have to be rebuilt. He never replaced the parts on previous invoices I received, and I filed a complaint with the BBB. Now they are completely lying. Technician trying to say I had the control panel apart which is not true, and does not match up with the invoices I received. They are telling me my warranty is voided! Its been a month and a half. I was treated rudely from the beginning and now I am obviously being retaliated against. I have 3 kids, two with severe medical problems and have put so many hours into calling with all these issues.I had another service place come out and he removed the agitator and the transmission shaft/drive motor is rusted out, as well as the parts he said he replaced are worn and definitely not new. For this company to come back after all this time and say I did this, when I have the original invoice that clearly states otherwise is absolutely the worst service ever.I bought this machine thinking it would last, and now have to deal with all this. I have nerve damage and it is very difficult to take all the laundry for a family of 5 to do at laundromat. They refused to send someone else out, where they could easily have seen this repair tech never did what he said, and was unable to diagnose and fix the issue. Its appalling to me that this is how they treat customers. Laura ** at corporate is the one saying warranty is voided. The machine looks brand new as it has always been taken care of. They should be ashamed of themselves. Apparently, this is the standard a lot of times with people trying to get things serviced under a Manufacturer warranty!

Maytag MVWB835DW was less than 2 years old (purchased 1-14-16) when it began to fail. Maytag sent repairman out, he declared it beyond repair. Machine locks, washes and adds more and more minutes and cant turn it off without unplugging 5-10+ times... sometime takes a week to get clothes out of machine because of locking itself. I have extended warranty and yet when I try to contact Maytag, to have them honor this, there is eternal wait on phone, online, no help whatsoever. I read via Consumer Affairs that there are almost 3,000 reviews on this specific machine being a problem yet amazingly the Maytag man never responds! I have spent many many hours with no resolution. Amazon says so many reviews have been written about this, that they are unable to take my review because of excessive reviewing.

Purchased side-by-side with bottom freezer 2009 after Hurricane Ike. Fridge has stopped cooling. Called Maytag Customer Center and was told nothing can be done only to find theres a 10 year warranty on the compressor. This malfunction should not be an issue after 8 years. My GE fridge still works after 25+ years. Horrible!

Like the other poor reviews here- this Bravos top load washer is the worst. So wish we had returned it!!! There is never enough water in the machine on normal cycle to get all the clothes wet so how in the world would anyone expect the clothes to get clean? Just ridiculous - and whoever invented this machine, plus those who tested it, need to have their head examined! Hate it so much.

MODEL # MDB4949SDMO. Purchased Maytag Dishwasher. 07/2014 stop working. I have purchased a Maytag Washer also. It also did not last two years. I am very unhappy consumer. I will not purchase another Maytag appliance. Stop selling these lemon appliances. Need to repair free.

The only time one can get enough water into the washer to actually get ALL the items wet (or even damp) is to put it on BULKY sheets or HAND wash settings. That is true for any size load whether it be 1 item or 10 items. I prefer being able to get ALL the water I need first, then put in the clothes, then soap, but thats not allowed. First soap, then items, then a bit of water only after you close the lid. They like to say that the spinout dries them which is why they arent damp - but that is a lie when you can smell and see the dirt. I want my OLD STYLE back!

I purchased a Maytag washer 5 months ago. I noticed the washer was not putting enough water in the machine to cover my clothes, and at the end of cycle my clothes would be all tangled up. A repairman looked at it and said there was nothing he could do. Do not buy this washer. It is a lemon. I even spoke to the main customer service representative, he was the most arrogant man I have ever felt with. He basically said deal with it. I want. I want my money back so I can purchase a washer that actually works.

I didnt want something from Sears due to horrible experiences with them. Maytag is very reliable and the cost was reasonable. They fit in the small space available for washer and dryer. They have all the features I need. The only complaint I have about the dryer is that for some reason if the load is small, it takes longer to dry than with a full load. I have had them for about 5 years now. I expect a washer and dryer to work correctly every time. If its poor construction I would not buy it. I also expect an appliance to last many years with proper maintenance.

Purchased our side-by-side stainless steel refrigerator. After about three months, we too have a constant puddle of water outside the bottom freezer door. Maytag came out for the first year it was under warranty, each time saying it was fixed. Its still not fixed and its been three years. We have to keep a towel next to the fridge constantly and have experienced floor damage. Class action suit? Sign me up!! My Maytag double oven has stopped working, and my Maytag dishwasher does not clean my dishes at all. I will NEVER buy Maytag again.

Dishwasher could do better with washing the dishes better and less recycling time. Also, it would be better if it had a self cleaning unit on it.

The washer is very aggressive - it will tangle the clothes and actually tear them if they are thin. There is little control with the speed or water temperature or with the amount of water for a load of clothes.

I purchased this machine (Maytag washing machine model MVWB700VQ0) from Home Depot in December of 2008. When purchasing it I decided to spend a bit more money on the machine, thinking I would get a quality product. For the last two years and 5 months it has only been me and my wife in the house as the kids are in college. Hence, the washer has not been used as much as some would use it. Within the last two and one half weeks the machine started making a horrible growling noise (probably the tub bearing going bad) and then started to leak yesterday. I noticed this morning that there was a large puddle of bleach water coming from under the machine. I called Maytag, which is just a fancy name for Whirlpool, and they basically told me too bad. It is inconceivable that a machine that used to last 20-plus years barely lasted three with only two adults using it. When I owned my previous home in another town the house came with Whirlpool appliances which literally fell apart within 5 years. I wanted to stay away from Whirlpool; however, I did not know that Maytag was owned by Whirlpool. I have received no assistance from Maytag. I am absolutely disgusted with the fact that an American iconic company such as Maytag is producing such garbage. I am going to be forced to figure out and fix what is wrong with the machine myself. However, I do believe this subject should be looked into further and possibly a class action law suit against Maytag for bad customer service since there seems to be quite a few people with issues surrounding this machine.

The washer does not get clothes clean at all even with the help of odor blaster, does not spin right, does not even out the clothes, walks while it is spinning. My towels do not smell good at all. The dryer gets too hot and the lint trap is always a mess even though I clean it after every use.

Havent even used the range yet and the paint is peeling off of the top. I have had the repair guy out. The new top piece of the range arrived with peeling paint also. I put in a claim to have the range replaced and was told they would contact me in 24 to 48 hours. That never happened and so I called again. They said that they would call and, of course, it didnt happen. I paid $1,300 for a stove that looks horrible with the paint is peeling off of it. What kind of ** is Sears selling? Maytag is owned by Whirlpool and nobody wants to make this right.

Faulty control board. Have owned a Maytag dishwasher model MDB6769PASI for 2.5 years. The unit started beeping at random times for about a week - then went dead! Sounds like other reported failures and it is unlikely repairs will be permanent! Never again Maytag.

We too were having a water leak from the French door freezer and a sheet of ice under the freezer drawer. The repairman came and told us that it was a common problem with the French Door fridge and an easy fix. Maytag has a new P type defrost hose that doesnt freeze up. He changed the part, $149.75 bill, and no more problem. Should Maytag have let consumers know this was a part that was failing? Yes, definitely. But at least the fix was reasonably cheap.

This will be the third repair of this refrigerator in one year, the same issue of the refrigerator warming up. Water all over the floor due to ice thaw. Also food spoilage. I want another refrigerator at this point. The Maytag repairman is definitely not lonely. He has more business than he can handle with this defective refrigerator. Terrible. Do Not Buy!!

Maytag washer, top loader, Bravo series: We purchased Maytag washer and dryer 4 years ago. Last week, the washer started sounding like a 747 was landing in our laundry room. Maytag sent a service representative and informed us that the bearings were faulty and it would cost at least $800 to fix. It is appalling that a 4 year old appliance should fail like this. We will buy a different make and we will never buy any Maytag appliance again. This is such poor quality and worse service. Maytag would only offer a 30-40% off a washer, but only if we bought it directly from them. We can get a better offer from any local store. They also said we could get a discount on the part we need, but not the service. Do not, I repeat, do not buy Maytag anything. You will regret the purchase.

I had my dishwasher for several years. Never had an issue with it. Cleans well and is very quiet which is exactly what I needed. A quiet and effective dishwasher is hard to find. The price was about six hundred dollars. I pursuit at Lowe’s. It was on sale along with a military discount.

Maytag #mbl2258es1 - started leaking in the freezer two years after I bought it. Two service men who did not know how to fix it. Now the refrigerator is not cooling. No more Maytags. Horrible refrigerator.

For families where people work in gardens, work on vehicles and get just plain dirty doing things anywhere outdoors these agitator-less machines are not for you or me. Ive had mine for two years and I truly dislike it (Model MVWC425BW1). With different products I scrub dirt and grease stains on pants before they are put into the washer, scrub again when they come out of the wash and then scrub and wash again a few more times but I cannot get all the dirt out. I now work more on laundry and harder since I got this machine.This agitator-less machine is designed for people who dont get really dirty - just remove everyday perspiration and household grime. I think this machine was designed by engineers who have never done daily laundry for any length of time and theoretically thought it would clean really dirty clothes. They were really wrong! Having done laundry for 50 years, I now know that an agitator cleans better. It would be nice if other women and I, who have done laundry for years, could be on focus groups about developing new washing machines.

We were delighted with our new Maytag refrigerator, model #MBF2258XEB, until the compressor died less than a year after we bought it. Home Depot, where we purchased it, directed us to the A&E Company for service. Two weeks later, we are still without refrigeration; Maytag refuses to replace it and even refused to overnight the new compressor. We thought Maytag set an industry standard for excellence. Don’t buy this product if you want a reliable refrigerator from a company that stands behind its products.

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

Replacing a working but noisy 14 year old Sears dishwasher for the newer Maytag was my bone head move for 2011. It died the first year control panel shot, no warranty. Paid for repair. This month dead again; same problem. Recall this stainless steel garbage. Maytag model MDBH949. Maytag, never again. Bought twice and last time.

I purchased a Maytag Dishwasher (MDB7749) in 2012 and one day before my 1 year warranty was up, my start button on the control panel wouldnt work. I called P.C. Richard and they sent a repairman who fixed it. This was in June of 2013. Here I am now hand washing again 1 year and 4 months after the repair. I called P.C. Richard again and was told that all brands have their weak points and because I got it on sale in the first place, I should not feel angry.Now that I am reading the reviews from 5 years ago, I realize that P.C. Richard knew this was an issue and chose not to disclose it or stop selling it. I had my G.E. for 10+ years and will go back to one. As I have no money for another new one, I will try to learn to fix this one on You Tube.

My washer is about one-year-old. Several months ago I noticed a brand new shirt was damaged after laundering. I thought it was inferior material. A couple of months later I saw a similar situation with another garment and started being more careful with the laundry settings using delicate, short, light washes, etc. The problem has happened a THIRD time to another garment. It appears this washer has a hunger for delicate jersey type fabrics. I started reading online and found out at it is indeed the action of the agitator and I need help rectifying the situation.

Nice refrigerator, but cheaply made. I paid 1800 with tax for my french door Maytag and expected higher durability. It operates well but one worries about breaking drawers made of such thin plastic.

Our Maytag microwave, which we bought based on Maytags supposed quality, is nothing but a piece of junk. In two years it has had or needs repairs that nearly double the original cost! Thats ridiculous. We are done with Maytag and are not going to get suckered into their Whirlpool/KitchenAid or other brands. So long.

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

Perfect for me. It would be better if I had a space to put it without adjacent walls. Mine sits with the refrigerator door against a wall and I have to pull it out to the door space to open it wide enough to pull out the drawers to take them out for cleaning. Otherwise, it has worked very well for me by myself, for me and my husband when he was alive and for my son and his family and myself, and he has 5 children.

We purchased a Maytag dishwasher MDB7609AWS2 in October of 2010. It first stopped working about 2 years ago. Since it was only 2 years old, we were disgusted and decided to let it sit and do dishes by hand. About 2 months after it had stopped, we tried it on a fluke and it worked. It stayed working for about 2 years. It finally stopped again, so we did the same thing, just let it sit. Every once in a while we try it to see if it works. It just recently started working again. We are wondering, what is up with this. We are not sure why or how the sitting works, and it is ridiculous that you have to have an appliance that you cant use periodically. We were too stubborn to have it fixed or buy a new one at this level of newness. We will get by in this manner for at least another few years, so as not to have lost all of our investment in a dishwasher, but we have sworn off Maytag appliances forever.

I was given a confirmation number to service my dryer. When I called the service contractor, Maytag provided. They said the appointment was cancelled and Maytag cancelled it. When I called Maytag, they said the contractor cancelled the appointment. I was never informed my service appointment was cancelled. I took time off from work and no one came. How can a third party cancel a service appointment without letting the customer know?? Is this any way to run a company and provide service? I have now taken two days off of work and do not have a dryer that works. I have never been treated so badly as a customer. My mistake was trusting that I had an appointment when I received a confirmation number. Why give a confirmation number when it is absolutely meaningless?

Horrific, useless, inconsiderate, rude, discourteous, arrogant and banal! I bought a brand new washer and dryer. The dryer is steam type and defective and they will not exchange, despite never being used. Nowhere am I committed to an agreement saying that the machine will not be replaced if it is defective. I am getting the run-around from the store, the manufacturer and the service technicians that didnt even arrive with tools when they came to evaluate the problem. If I had my way, I would return the washer and dryer and change manufacturers. But it is a stacking unit and I used the washer which commits me to it! Maytag, Whirlpool, JennAir and KitchenAid are all the same company. I am running out of options except going to the European manufacturers! Miele will at least install the appliances. They will be my next machines and I will not have to pay a plumber twice to install them the next time!

I read some of the reviews on the Maytag ovens. I too have the same problems! Have had control panel replaced and still have to set at 400 if I need to bake at 350. It also takes forever to preheat. Trust this review because I am one very unhappy consumer!! DO NOT buy Maytag!!

This machine that I bought 2 1/2 years ago is very loud. Sounds like a helicopter that is going to hit the house. Last week the machine did not empty and would not spin. What a mess. We had to take the clothes out and try to wring them out by hand. Then we had to scoop all the water out. Had to call a repairman to fix it. $187 which included two trips to the house and a new pump. The pump was $56. Just the last year my grandson came to live with us, but before that there were just two of us in the house to do laundry for.

Got woken up to the sound of my refrigerator ice lid flapping. Boy is it loud! Called Maytag and found out it was a recall so they will fix. They set up for someone to come out to fix the following week. That was a flop because they did not have the part. I waited 4 hours for someone to show to find out that Maytag scheduled the appointment for nothing - not only did they NOT have the part but they did not have a clue as to when it will come in. Time is valuable! Here we are 5 weeks later and my refrigerator is still flapping and loud. Has been calling Maytag for them to say that the part has been expedited. Well it has been expedited for more than 3 weeks now! Today they say that it will be another month before the part comes in! Not Good! This is such an inconvenience and Ive lost a lot of sleep over this flapping noise. Its an embarrassment when guests come over to our home! Tired of it!

Both Sears and Maytag have lost my business FOR GOOD! We purchased a Maytag Bravo XL # MGDB980W0 2 years ago. We called within the 1 year warranty period via Sears, they sent a tech out then charged us. The dryer kept shutting off before clothes were dry. We thought the problem resolved, then reoccurred after the 1 yr period. Neither Sears or Maytag would stand behind the product citing it has been discontinued due to problems. Well... yeah, no kidding. We paid BGE energy efficiency company to come out and evaluate it. They tweaked the exhaust vent and cleaned out the duct, however, they said we needed a new sensor. My wife bought a new sensor, installed it, and the dryer still wont work right! (Shutting off prior to clothes being dry). BOTTOM LINE UP FRONT: I researched and bought a new gas LG dryer on sale at Home Depot and shelled out $849 unnecessarily thanks to shoddy product and lack of company integrity. DO NOT BUY SEARS OR MAYTAG!!!

My stove is approximately nine years old. During the past year both my husband and I enjoy cooking from recipes 3-4 times a week thus the stove has become essential. Functionality and size is important when trying to cook meals with two or three components. One of the oven racks was missing from the oven when we moved into the house. Even though it is self cleaning, spills pile up between cleanings so it is great that it has a really cool steam cleaning option. Just wish it were 5-6 years newer.

I have owned this Maytag washer model # MVWC360AW0 since Dec/2013. I do not have a single complaint about this machine. It has worked flawlessly for 5 years and am very happy with it. I just follow common sense maintenance like cleaning it once every month (do a full cycle with just borax & baking soda 1/2 cup each) no clothes of course. Another thing I do is to leave it open after I am done washing so it dries completely before I close the lid. The washer looks and works like new, cant be happier...

So the reviews for the Bravos MCT online were pretty decent. We purchased our set from Lowes. However, the clothes dont turn over. I watched as long as I could (getting frustrated the longer I watched) to see how the clothes were going to get turned over and washed. All they did was get rubbed on the bottom of the pile where those agitator fins are. But they never got a good flipping so that the top of the pile was washed. I only had 4 normal size towels in there. So it isnt like I had too many clothes.So I called Maytag to tell them what I was observing and the gentlemen explained that it was counter-intuitive technology and that it seems like they wont come clean but he promised me by the time the load was done they would be clean. Yet - they did not come clean! The dirt on the towel was still there on the top of the load with dog hair. NOT TO MENTION SUDS!! Im so disappointed because the burden is on me to either take this set back or deal with it. Buyer beware - if you look at this machine and ask yourself how in the world will the clothes get clean - you are asking a great question! They dont!!

The Maytag Neptune TL washing machine has always been extremely loud! It smells awful and now our clothes too! I have found mold in the washer and cannot get it all out even with bleach. My children are extremely allergic to mold and they have had problems because of this. I am very disappointed in this washer and find it sad that no kind of action has taken place to help people who have bought them.

Fridge leaked all over our floor and ruined it! Very unhappy! When we open the freezer we find a sheet of ice on the bottom. We have to keep a towel on the floor so we dont slip and get hurt. I finally get a new kitchen and the fridge is ruining it! Yuck.

Purchased this Maytag dishwasher (Model DB7749SBM2) from a Sears 2014, no problems until now in late June 2014. The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond. Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, cannot be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only. Control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem. We need help as we are unable to afford repair or another dishwasher. This time, it will not run at all. I called customer service today (August 11, 2015) and they expect me to pay for the repair. Repairman already said electronic board bad at a cost of around $300 just for the parts. It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 1 1/2 years it is becoming very expensive. There should be a recall on this control panel.

I, too, am having major problems with my Maytag Neptune washer, much like many of the writers are. I am extremely disappointed in the Maytag corporation for putting out such an inferior product that it wont stand by. I wonder if a new class action suit could be filed.

I purchased a Maytag Centennial - HE Energy Star Washer from the local Home Depot on Guam.... Probably the worst clothes washer I ever purchased. I typically buy a Whirlpool brand for many of my appliances of which I have always been satisfied with the products. I understand that Whirlpool is now the new principal owners of Maytag. I bought the Maytag for my new second home which I have moved into as my primary residence. Great ads on TV that promote the Maytag product line but the product fails miserably in performance. From the day I purchased the washer, my wife, kids, and I visibly noticed the laundry doesnt get as clean as my previous washers, it takes longer to wash a load of laundry no matter what is the preferred setting, the irritating hum is deafening in my laundry room, now the washer has malfunctioned and doesnt cycle through properly, leaving the clothes either unwashed or wet... I do not know who is your servicing agent or center on Guam and I am debating to repair it or just dispose of it. I can tell you now... MAYTAG... NEVER AGAIN. Now I know why the Maytag Repairman is so lonely.... I wouldnt bother to repair it. I hope these issues do not filter down to your Whirlpool products. That Samsung is looking pretty attractive right now. I bought one of their dishwashers that is doing a pretty good job right now.... Guess what? There was a Maytag next to it that I didnt even look at.

Can not wash 4 pairs of pants or 2 sheets because they get out of balance when the spin cycle begins. I had to take the clothes out and move them around to keep the balance. Very unhappy. Would not recommend this washer.

I had a Maytag washer and dryer for over 25 years. I loved them so I replaced them with the Maytag name. They are not the same company as far as pride and product workmanship.From the get go it always had a dirty odor to the tub, as though the clothes had been left in it for days. I was told to just run through a cycle with bleach, but nothing. There is no lint collector and after about 8 years of using this washer, the old lint is in the bottom of my washer after every wash. Now, I have to deal with the thing coming to a screeching stop, not spinning out the water after the wash cycle. Sometimes it’s full of water and other times some water drained, but the clothes are full of water and not spun out.Now tonight, I went downstairs and found water on the floor, it’s leaking. My question is to call and get it repaired or not waste my money and go buy another brand. I may go with the latter.I purchased a fridge and dryer at Home Depot a few years ago. I wanted to stay away from Maytag name. I purchased another name only to find out it is part of Maytag. No wonder I’m having trouble with my fridge, making ghost-like howling sounds so loud it consumes the entire house. So annoying. Stay away from Maytag. They are not the same reliable, take-pride-in-work company.

The pulley on the dryer vent keeps falling off due to poor design. We had a repairman fix the problem under warranty, but the dryer was purchased in 2010 and this is the third time it has fallen off. I have taken the dryer apart and repaired it myself, as I am quite capable, but I called Maytag Customer Service to see if there is something else I should do or replace. They told me they never heard of the problem and they would recommend a service man repair it, which would cost me money and It wasnt needed. No updated part was recommended, or any other help at all, for that matter. I am very unhappy with the Maytag products and will never buy anything again.

This washer is only two years old and does the wash for 2 people. The control board has broken down and the lid lock did too. Of course the warranty had just expired, so there is no help from the maker, Whirlpool. Save yourself a big loss and dont buy these brands. Mine is going to the dump where it belongs. Thats $500 down the drain. Do yourself a favor and get a Speed Queen.

After reading several of the reviews, it looks like Maytag doesnt get it - or maybe they do and its a plot to make more money. Our dishwasher model MDB8959FSZ4 was installed in Dec. 2016. Within the year, it started leaking. After many service calls it was determined that the arms holding the upper rack were not installed properly and were pushing against the door and water was coming out. After that was replaced, weve had 2 years of relative good use. Now, it wont empty and that started after smelling something burning. The burning smell has gone away but it wont complete a cycle. Service tells us its the drainage pump and that will cost nearly $500 to replace. We wont be spending another dime on this piece of crap. Well replace it with NOT A MAYTAG. Im wondering if it has to do with the control panel as many others have mentioned. We dont care to find out at this point. We are buying something else.

First bought a nice looking Samsung. Didn’t last 6 months. Upgraded to a nice Maytag with steam and have never regretted it. It’s been years of worry free and trouble free use. My Samsung dryer is on the way out the door and to be replaced with a Maytag too.

Recently purchased a washer from Home Depot. Machine is now on its 3rd repair. The wiring harness is fired. Could have caused a fire. Now they still will not replace and part is on order which will take 4 weeks to be in stock. I called Maytag and expressed my concerns to which they could not help me as every washer is theirs can be repaired. I really don’t understand what happened to making things right. Very frustrated that they will not repair or reimburse for that matter. Please refund my mom and pick it up.

I bought a Maytag washer and dryer with Commercial Technology, front loader in April 2012. Since then, the repair guy has been at my house three times in six months. This last repair is going to be just $800 in parts, not including any labor yet. So, I called Customer Service, and told them I was not satisfied with the repair job again, because I obviously have a lemon of a machine. Needless to say, I lost, and was told the warranty is only for repair, and not replacement. Well what happened to customer service? Its more like customer bend over, shut up and take it. So, I will get my repair at a cost of at least 1,200 bucks paid for by Maytag. Im not a business person, but if I were the company, I would think replacement of the unit would be a lot cheaper in the long run for this company and a happy customer for the future of me buying brands. Needless to say, I will never buy a Maytag or Whirlpool product again, and you can thank your useless Customer Service department in Canada for that. P.S. I work for a company with over 10,000 employees. I might accidentally send out a little free publicity how this company treats loyal customers. I actually bought this brand because in the past, I was led to believe they were great . Wow, was I wrong!

I have had two Maytag washing machines in the past. Both lasted 20 years. Three years ago I purchased my first Maytag front loader washer and dryer. The washer is terrible. Although I clean it regularly plus spend money buying Affresh tablets and leave both the door and the soap dispenser open, the washer smells and builds up tons of mold. Cleaning out the heavy mold in the soap dispenser area is almost impossible. I spray bleach in there and then try to stick my arm into the back where most of the mold accumulates. Cant really get it all. Also, there is a problem with the softener dispenser. It gunks up and gets clogged. Had to keep pouring hot water and vinegar into it. Contacted customer service who was no help - they simply wrote to clean the machine. Huh? The dryer turns sheets into a tight roll with the inside not drying.

We bought a Maytag dishwasher in August, 2014, and already the touchpad is malfunctioning and we cant start the dishwasher! I am very disgruntled and frustrated by this! I should have kept the old Kitchen Aid dishwasher that we bought in 1995! At least it never malfunctioned!

We bought all new appliances for our remodel. I wish I could return this dishwasher. It has a problem with the door staying closed. I added images of how we are able to make it work. A service person is coming by tomorrow to put a new latch on it (I read several reviews saying the latch is messed up). So I made sure the service person is coming with the part. I called Home Depot when the problem started (used for up to 5 washes or so). And Home Depot wont return it! I called Maytag and they tried selling me an extended warranty and I asked what about the 10 year warranty the machine is supposed to come with? I guess thats a joke as the lady told me I should of read the fine print. So buyers beware! I wish I would of know about Maytag. I would have about a Samsung instead!!!

I purchased a Maytag MDB7749AWM model dishwasher in March of 2012 for approximately $600. Fifteen months later, the control panel has gone out on it. From what I understand, this problem happens so often that its not even worth repairing this dishwasher.

This Maytag Bravos is the worst washing machine I have ever had. Who ever heard of washing with almost no water? Takes way too long. Clothes not clean. Any water savings way offset by ridiculous length of washing time. I can wash and dry a load of clothes in an old stacking washer/dryer before one finishes washing in this thing. I was excited to get it and now cant wait for it to go. Wont make this mistake again.

We purchase a matching Maytag washer and dryer set and within the first three months our washer began to give us error codes and would not wash our clothes completely on any cycle. It was repaired and we began to have the same issues within the next couple of months. This all happened within the first year. We called customer service about extending our service warranty due to the multiple malfunctions of this washer. We were given the run around and, quite frankly, the attitude that this was not their problem. I WILL NOT BUY ANOTHER MAYTAG PRODUCT! Thank you customer service for ensuring that I will not be a repeat customer!

My dishwasher was bought December 2013. The control panel just started going crazy and cant control anything. Unless you have bought extended warranty Maytag isnt doing anything. This is obviously a manufacture defect and no one is doing anything about it. Will no longer buy Maytag products if they cant stand behind their product.

We bought the washer less than a year ago. The washer became off balance with an average load of jeans. The washer shook so violently that it cut our floor, busted our wall, and broke itself. Water covered our floor! We have now been over a month with no washing machine (still paying on it, by the way). We have had to pay to get our clothes washed in the last month = EXPENSIVE! The repair company has been out to our home twice, broken high-quality tools trying to repair the machine, and told by their higher-ups that the washer can still be repaired. Customer service only tells us that we have a repair warranty and the first repair has no time limit.

Failed after only 13 months with light use. I have a Whirlpool extended warranty which I had to fight to get them to honor. Then someone came to fix my washer and needed part was ordered, but part isnt available and company wont tell me when it will be. I have received 6 part availability dates so far. Whirlpool wont help. Over two months now without a washer. Ive asked them to replace machine or give me my money back, but they refused. The Whirlpool Extended Warranty group doesnt answer their phones, was put on hold for a long period.

Our refrigerator is just 2 years old and it have been leaking for over a year. It started leaking right when the warranty expired. I am so mad. I called them and they said... You can purchase a warranty for $400. I am like.... what!!! I called my home warranty and they fixed it for $100. A few months later it is leaking again! I am so mad... It is a $1200 refrigerator. What can we do as a group to fight for this? There have to be something that we can do?? It is so frustrating. If there is an attorney that can take care of this group that would be great.

Well, my washer is 2 years old, yes thats right - 2 years old. And it only goes to the wash cycle, washes once and stops, wont complete a full cycle. Yes, the brand with the commercial with the repairman just sitting around because their products are so great you never have to work on them. Yeah right. And Ive seen videos on YouTube on the problem with the Maytags. So Maytag may want to look into it!

Purchased a Maytag top load HE washer in November of 2011 & by Feb. of 2012, Maytag had to bring me a new one after a service call to fix lasted only one week. So at the end of Feb. 2012 they brought me a new Maytag Centennial HE Model# MVWC400XW3 & this one lasted till January of 2014, less than 2 years old & quit working. Had a service man come out to look at it & was told not only it would need a $400 repair but it was made by Samsung, but Maytag had their nameplate on it!! Called Maytag customer service line which took about 30 minutes of hold time to get through & was told, SORRY, LADY, we cant help you. Youre just out of $613 after less than 2 years of service & we WONT help you!! This company should be shut down, they are liars, frauds, cheaters, producers of poor quality products, uncaring, & sellers of the worst products on the US market & I hope the Consumer Affairs will see enough of these complaints about Maytag products & shut them down!!!

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

The engineers at Maytag saved a few pennies by only using one thermistor for temperature control. It is in the box. There is nothing monitoring the temperature in the freezer. If you put your fridge in the garage where the temp is 40 degrees, the motor will never come on, and your frozen foods will melt! In my new MRT118FFFZ01 unit, the temperature in the box varies by plus or minus 3 degrees F, but the freezer varies from minus1 1 to plus 25 degrees F. 36 degrees difference! Lousy design. Have had two service calls, and they both said that this was the way it was designed and there is no fix for it.

I have Maytag dishwasher model # MDB7609AWB2. I purchased it from Sears on 5.30.10. It was installed 3 weeks later. From June 2010 through November 2011, the dishwasher has stopped working 3 times, every 6 months, requiring a service call to fix the electrical /circuit board problems. The aggravation of owning a poorly built machine and inconvenience of waiting for Sears to send a repair person has sealed our decision to stop doing business with Sears and Maytag.

I had to rate at least a one star because there isn’t a negative to rate. We bought the Maytag mvwb955fc1. First off it doesn’t clean our clothes. I can not get stains out or whites bright. I don’t feel it uses enough water. I put a full load in and it only fills up less than half with water. I try half loads and still not clean. It’s always shutting off when I wash sheets. Indicating it’s off balance. Today I started it before work and the lid exploded. I don’t think I want to even replace it at all. This could have seriously hurt someone. Do not buy this washing machine. The dryer is great so far. I wish I could post a photo to show you all.

It does not completely drain all water out of until. So unless your running the washer every day, you will end up with the most horrible smell coming from standing water. It is very irritating and so fowl smelling.

Worst washing machine I have ever owned. Read all the other reviews and concur with them. We get pin sized holes all the time. Brand new shirts yesterday and they have black stains all over them - not the first time either. Inside of stainless steel tub looks clean. Where do the black marks come from? Last Maytag I will ever buy!!

I just found this website & do not have my model info with me. But we have bought 2 Maytag refrigerators since 2001. We still have the 2nd refrigerator but I want to replace it as soon as we can. They were different models but had/have the exact same problem. They freeze up into sheets of ice and then leak puddles of water on to the floor. Makes me mad when I see their ad about how great their product is - what a load of crap! My first refrigerator was a General Electric; it was still running after 19 years when I left the farm. I still have my 2nd General Electric refrigerator (18 years old) down in my family room - running like a top! NOT EVER GOING TO BUY MAYTAG AGAIN!

I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

I purchased my 2nd Maytag Neptune washer in 2005 to replace an early Neptune that was complete junk. This one worked OK until this year when it began to make awful noises. After research, I decided it was the bearings that failed. I took the unit apart to get to the bearings and found out the entire outer tub must be replaced not just the bearings, at a cost of $515. What lousy engineering, the bearings dont come out of the housing. No wonder Maytag repairmen are so bored. There is nothing to fix, you just buy a new washer. I wont buy Maytag this time.

I purchased this set 7 years ago and the washer started stopping mid-cycle and the dryer sensor doesnt work. I called the Maytag service number and after several phone calls (they had my name spelled incorrectly and the wrong address), was able to schedule an authorized servicer. He said the motor and motor controller needed to be replaced and it would cost over $900. When I said I expected my $1,200 washer to last more than 7 years, the service person informed me that the machines were made by Samsung (not Maytag) and just carried the Maytag label. He said the Maytag Neptune washers and dryers were the reason Maytag went into bankruptcy and was bought out by Whirlpool. I am disappointed Whirlpool/Maytag does not stand behind this product and will not buy this brand again.