I purchased a Maytag top load HE Bravo 700 3 yrs ago. I only wash 3 loads of laundry a week and the bearings went bad in the washer! Maytag/Whirlpool will do nothing to help me because they say I should have purchased the extended warranty. Well there is NO WAY that I could have worn out those bearings; it was a manufacturing defect that caused them to fail and hundreds of people online all say they have the same issue. The repair cost is $400 and would only have a 90-day warranty so I might as well purchase a new washer. Home Depot (where I purchased the washer) has been very helpful and is offering me help on the purchase of a new washer, but even they could not get Maytag to do the right thing and repair my Bravo. I am going back to a none HE machine with an agitator. This has been a horrible experience and Maytag has no business putting commercials on TV that say they are dependable.

Overall I am satisfied with my Maytag Model MDB8859AWW2. I purchased the dishwasher 06/05/201. However, the door spring squeaks. It is a grating sound.

Purchased an expensive brand new home which had Maytag appliances in it. After about 1 1/2 years the freezer bottom began to constantly freeze and drip onto my floor. I researched the issue and found it was common, simply thaw the area where it freezes. Did it multiple times, we do not overfill our freezer etc. We must take the ice out of the bottom every 4-5 days. My hardwood floors are destroyed now. We purchased a Samsung fridge freezer bottom when they first came out years ago, had it for 7 years, 0 issues, but it went with the house. Now my Maytag oven door is locked shut, also it takes a very long time to boil water. Maytag junk. I am going to buy another Samsung fridge tomorrow.

Neptune washer maxima XL steam - Our machine is only 2 years old and we feel the soap dispenser is defective. That little door inside to choose either liquid or powder is not flush with the basic cup and to make matter worse, there is a V shape hole at the bottom of that little door. Meaning, fill it up, and while you are looking for the softener in your closet, all the expensive liquid HE soap is on your floor! And when you close the door, if you wait for starting the load, all the soap goes into that rubber gulley instead of being sent over the clothes. I just got off the phone with them, they wanted to send a technician AT MY EXPENSE - when I do feel it is a deign mistake, not a use/abuse on my part. I proposed instead to send them a picture. They refused. I proposed to send them the soap drawer, they refused as well. I will never buy Maytag ever again and dont recommend to anyone to go to this Brand name!

We purchased an entire suite of Maytag kitchen appliances in September 2014 at a cost of $4300. Have had problems with every single item. The MMV5219DH microwave was the first issue. After a year it began to give us erroneous display messages when we tried to use it. We would input the number of minutes we wanted the food to cook, and wed get a message saying CHK TIME/OPEN DOOR. Repeated door closings, resets of the time, etc. did nothing. Sometimes if we hit cancel it would work - other times not. Wed push every button on the keyboard and eventually wed get it to work - perhaps 10 minutes later. When I called the appliance store (Vics Appliances in Saco Maine) I was told to unplug it for an hour. Okay, that corrected the issue - for a few days. When the problem continued, sometimes unplugging it had no effect - other times it did. Eventually we figured out if we didnt reset the clock time it would work most of the time (not 100%). The Maytag refrigerator began to malfunction at the same time (not keeping temp, and the ice in the icemaker melting and refreezing in a big lump that blocked the door water/ice dispenser) so we called Vics again and set up a service call. Serviceman reset the microwave to factory specs and we will see what happens. He also reset the fridge to different temps, and 2 days after his visit it has again melted the ice in the icemaker and formed a blob at the bottom. DO NOT BUY MAYTAG!!!

I purchased a Maytag dishwasher in 2010 model MDB6709AWW1. I only had it a year and the control panel went. They came out and replaced it and the guy told me that they were having a lot of the same problems. Now in 2015 it has gone again. It will run, but you cant change the settings. I took out the extended warranty on it and called 3 weeks ago and they sent out a local appliance repair company. This guy told me he had just come from another house with the same dishwasher with the same problem. He ordered the parts and I have been waiting 2 weeks. I called and the lady told me that they changed the part # and that they dont have any made yet and dont know when they will. WHAT!!! How can a company not have any parts made for their own dishwasher. I didnt buy the dishwasher when I bought all my other appliances, because there was a dishwasher here. It was gross and didnt work well. All my other appliances are Kenmore and I will stick with them. Have owned them for years and never had any problems.

Buyer beware. This machine has received several complaints. Not long after purchase, the washer started to stop during the fill cycle and give an error code no. This is supposed to be sure to overloading the machine. The other reason they give is something stuck item the baskets. Again not the case. Supposedly it must be a motor issue. Maytag was my trusted band. Our last Maytag lasted us almost twenty five years.I was excited to get this machine but disappointed with the lack of clean clothes, error codes, and noisy operation. My first clue should have been the one year only warranty. Thats how much they believe in their products. Ill never trust Maytag again. So sad that whirlpool should sabotage the Maytag brand and turn an otherwise great washer manufacturer into a piece of junk manufacturer. Dont buy whirlpool either as thats how much they care for customers.

This washing machine worked great for just under 3 years. I noticed it wasnt draining completely. Per my appliance repair guy, the bearings were shot & it was going to cost over $300 to fix it. Called Maytag because my owners manual stated I had a 10 yr warranty. Wrong. The warranty only covers the wash basket & the drive motor. Look on Maytags Facebook page & you will see pages & pages of complaints on all of their appliances. Refrigerators, washers, dryers, if its got a Maytag name on it, its broken. Many of these appliances worked for only a year out two before they bit the dust. I went to Maytags fb page & ranted about their poor quality products & Maytags refusal to stand behind their products. Know what happened? They sent me an email stating that theyd reviewed my case yet again & there was nothing they would do. Then they blocked me on fb. Yep. Please please before you buy any Maytag/Whirlpool/KitchenAid product, please dont! Save your money & buy another brand. All Maytag will do is send you a form letter telling you they understand your frustration & you can email them your info, theyll investigate & get back with you. When (if) they respond theyll tell you theres nothing they can do. Basically you are sold, too bad, so sad. I now have a $600 piece of junk sitting in my garage. Im hoping I can get $20 out of it from the scrap yard.

I purchased My Maytag Washer and Dryer set from Lowe's, which was a very good experience all the way, back in June 2017. After two years I can finally give an honest review. We love this set even though it is not as quiet as the old Maytag washers. Still is but not as. We have not had one bit of trouble from either the washer or dryer. The next size larger would have been the better choice for us since we now have king size bedspreads to wash. It still does the job though, just one piece at a time. A lot of people complain about the smaller amount of water used but it still cleans clothes quite well. If you need more water just use deep water wash or for even more water use the setting for bulky sheets which really fills up the water level.

Maytag model mfd2561hes French door stainless steel purchased in June 2005 has been the worst appliance purchase ever. After 1 year warranty expired, icemaker and water dispenser stopped working. Was told by repairman to thaw the tube for water dispensing with a hair dryer. Are you kidding me? Why should I have to pull a huge refrigerator out from wall and put the hair dryer to it to thaw out the water line when I need water? What is the convenience to that? Cant buy fresh vegetables as it will freeze before I can use it. This is the worst appliance ever. Dont buy Maytag products. Maytag doesnt back products like the old days when they would last 20 + years. Cant last even a year anymore. Sad!

I bought this washer less than 4 years ago and its already broken (leaking from the basket). Maytag refuses to honor their warranty and is charging $400 to send someone out to fix it even though it specifically says in the warranty that the basket is covered. When I mentioned this to the rep, I was told that does not apply to all washers. I expected better service from Maytag and thought it was a reputable company. I will now have to purchase another washer, rather than spend $400 to fix this one. It definitely will not be a Maytag!

Maytag will not fix 2 major issues with new $700 Maytag dryer bought from Home Depot who takes no responsibility. They wont return it. Maytag wont replace defective dryer unless technician from totem appliances cannot fix problem. The tech ordered a control board and timer. Only installed the timer. He did not fix 2 issues. Dryer never stops at OFF. Dryer leaves damp spots on any clothing whether small or medium large load. Was told by Maytag if damp spots then its OUR problem... our ventilation. No it is your sensor. Our model is ymedc465hwo serial m820. 07331. Bought in late Oct. 2018. Two supervisors later we are being sent to tech or tech company and played games with. All I know is Maytag sells defective dryers then wont replace them or fix main issue.

This Maytag dishwasher works great if you are using as a sanitizer for your dishes so long as the dishes were soaked already. It stinks if you do not use it often and requires a lot of bleaching.

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

After a year or so my Maytag fridge is leaking, I followed instructions on how to remove ice clogging the drain pipe and fixed the problem. I see that this problem is going to repeat over and over again for the life of this unit, because of a poor design.The design fix will be to add a small heater (at the location where the ice creates the clog) actuated periodically by the control board, or at least with a manual push button for the user can easily remove press the button to melt the ice clogging the pipe. This is a cheap design which did not go through design validation and qualification.

I purchased the top model Maytag dishwasher, and within four uses, I noticed major water damage to the side of my cabinetry. I pulled out the dishwasher and realized it was coming from the side unit where water enters the tub. These things happen, and I phoned their customer service department expecting this unit to simply be replaced, being that it was less than a week old, and that I would have been left a satisfied customer. They were willing to send a technician over to try to fix the problem, but not replace it. I now have to replace my cabinets, and maybe even my granite as it may be damaged in the removal process. I am not asking them to fix that even though the damage was caused by their dishwasher, but a new dishwasher, I did expect them to cover. Their customer service stinks, and I suggest to anyone that if you have any problems with a new unit, the best thing to do is return it to where you bought it. Im sure they will gladly give you a new unit and send the bad one back to Maytag. Dealing with Maytags customer service is the worst thing you can do. They do everything in their power to not replace it. Instead, theyd rather lose a customer for life. Whats sad for them is that Im a builder, and I usually build approximately three houses per year. Thats a lot of units theyve lost sales on over a simple replacement of a dishwasher. Its not a good way to do business. The bottom line is, stay away from Maytag.

I purchased a Maytag Dryer Model MEDC200XW1 Electric Dryer in November of 2011. Along with a Maytag Washer from Home Depot. This week the dryer stopped heating for no apparent reason. I use it about three times a week. I tried to speak to Maytag customer service, they were very rude and did not care I spent thousands of dollars in kitchen appliances as well. They would not even cover the service call or diagnostic or half the repair cost. Supervisor Brian @ Maytag Customer Service was rude and unprofessional. I will never buy their product again.

I purchased a washer & dryer from Lowes on December 3rd. On February 20th, my washer stopped filling up. I called customer service and had someone come out a few days later. The repairman said the sensor broke & it would take 10 days for part to come in. After 2 weeks, I tried calling repair company and they would not answer phone for Maytag, or me. Maytag called another service provider, and it will be another week before part comes in. Never could get in touch with anyone who was helpful! Now it’s been a month, and still not fixed!

This has been the worst washing machine I have ever owned!!! Purchased 3 years ago and this is the 3rd time the bearings dont work again. It make loud clanking noises. Then fails to spin at all. The first time it broke was the 1st year we owned it. It is sitting in our hallway and I can hardly wait for it to leave my house. Talked to the local appliance dealer and they never recommends these washers. I told dealer I must have gotten a lemon. He replied that it wasnt a lemon, that the machine tubs have gotten so much bigger and they have needed to upgrade the bearing system and are unwilling to do it. Dealer has highly recommended the Speed Queen. Based on the stellar reviews that is what will be coming to our house today. I can hardly wait. I know, its just a washing machine but frustration has overcome me. The Speed Queen has no plastic parts. We went with the knob style as opposed to the electronic push buttons. Less to go wrong. The warranty on the Speed Queen is top of the line, 5-year parts and labor. The salesperson didnt even try to sell me a warranty. No need to. Speed Queen stands by their product. I only recommend the Maytag Bravo XL if you dont have enough stress in your life.

We moved into our first house just over two years ago and decided we needed to get a new refrigerator. We did a ton of research online, reading reviews, etc. We found a few not so great complaints regarding Maytag; however, we took our chances. (Note that we live in a house built in the 40s, so the fridge space is small and we needed a fridge size that is smaller than normal. We didnt have many options.) Well, a little less than 12 months later (yes, luckily right before the warranty expired) our ice dispenser stopped working properly. The mini-ice door would not close properly, resulting in a lot of frost in where the ice door was located. (There was so much we couldnt open the freezer door. It would get stuck.) So, we called out the repair guy and he said he had never seen this issue before and basically had to replace the whole flap and parts. Sweet. It was fixed and cost was covered! Well, about 5 months later, it happened again! Ah, they got it fixed yet again. Well, another six months later and after the warranty expired (lucky us), the fridge completely stopped cooling. (And it just happened to be Halloween, not a great day for a house issue.) So, we had to remove all our perishable food and place it in a cooler (which works hundred times better than Maytag products), and move all frozen food to a family members house 15 minutes away (luckily!). We were also super lucky we found a repair company that could come out at 5pm the next day, which happened to be a Friday! Awesome company (Conners Repair in Metro-Detroit). He concluded the defrost board was broken, meaning it was freezing and creating frost and then not defrosting, clogs the vents and not allowing circulation to occur. He was shocked when he found out we only had this fridge for 2 years and said this is something that normally happens in 20-year old fridges. I then decided to call Maytag and nicely requested a refund for the issue. I was told no due to the warranty expiring and also because we didnt use a Maytag repair company. I didnt want to wait a week as I thought this was something that needed immediate attention. I also am not sure why it matters who you get to fix your fridge. I have an invoice for proof of the issue and the repairman even said hed call to verify the issue. I don’t understand why I have to pay for something that was not properly produced, and not to mention the time out of my schedule to deal with Maytags issues. I now know not to buy any Maytag products due to the lack quality. I guess I learned the hard way.

I purchased a Maytag commercial residential washer in late 2018, supposed to have a warranty for at least 5 years. We are in California and I was told that there was only one facility that could come two weeks later. I removed the front panel to have it ready for service tech, who on the first visit kept saying he did not know what the problem was, and left telling me he would order parts. After Christmas, I could not get in touch with service so again called Maytag. Service was supposed to come out on the 30th.After waiting almost 3 hours, he called to tell me he did not have the parts. Also, this repair tech treated me very bad since I removed the front panel which I thought I was being nice. He called me back on the 30th, said someone gave him a part, and came. All he did was remove control panel, lost the start button and told me it worked without checking it at all. He was rushing to another appointment so I tried to start it and it still had the original issue, which was slow agitator and a rubbing/grinding sound. Now, after he did something with control panel it had a clicking sound. I immediately called corporate and was told when he came back, which has now been over a month with no washer, that he would be with a senior technician.January 5th I waited all afternoon and he called and said he was not coming and that my whole washer would have to be rebuilt. He never replaced the parts on previous invoices I received, and I filed a complaint with the BBB. Now they are completely lying. Technician trying to say I had the control panel apart which is not true, and does not match up with the invoices I received. They are telling me my warranty is voided! Its been a month and a half. I was treated rudely from the beginning and now I am obviously being retaliated against. I have 3 kids, two with severe medical problems and have put so many hours into calling with all these issues.I had another service place come out and he removed the agitator and the transmission shaft/drive motor is rusted out, as well as the parts he said he replaced are worn and definitely not new. For this company to come back after all this time and say I did this, when I have the original invoice that clearly states otherwise is absolutely the worst service ever.I bought this machine thinking it would last, and now have to deal with all this. I have nerve damage and it is very difficult to take all the laundry for a family of 5 to do at laundromat. They refused to send someone else out, where they could easily have seen this repair tech never did what he said, and was unable to diagnose and fix the issue. Its appalling to me that this is how they treat customers. Laura ** at corporate is the one saying warranty is voided. The machine looks brand new as it has always been taken care of. They should be ashamed of themselves. Apparently, this is the standard a lot of times with people trying to get things serviced under a Manufacturer warranty!

I purchased the Maytag dishwasher a little over two years ago (MDB6759AWQ0). This was the first Maytag product I bought and it is definitely the last one! It was more expensive, but because of Maytags commercials on what good products they had, I thought it would last longer and work better. Boy, was I wrong. When it was installed, it was loud. I brought this to the attention of Maytag. I was told there was nothing that they could do. Repair people were sent to my home several times to see if the noise could be fixed and unfortunately, it could not. This is the loudest dishwasher that I have ever had. I should have stayed with the same brand that was over 10 years old that died! Now the control panel blew out and will cost over $300 to have it fixed. After reviewing the numerous complaints that you have on your dishwasher with the control panels not working, I would think Maytag would be more financially responsible in helping the people that have your products that no longer work after being less than three years old. Just a heads up, Maytag, I will be replacing instead of fixing and not with another Maytag product!

MF12665XEM7 Maytag Fridge water runs on the floor: After reading the review and watching the video to fix, I called Maytag. They refused to help. We bought our fridge at Nebraska Furniture Mart. We have spent a lot of money with them too. My husband called to see if they would split the cost of the service call. They refused. My floor is ruined from the water leakage onto it when we are not home. We try to catch the ice buildup and remove it before it is an issue. Why is there no class action suit? There is definitely a problem with this fridge and Im seeing it online everywhere I look.

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

Bought Bravos XL washer/dryer from Home Depot in November 2014; installed 12/8/14. First repair was in March 2015! Clean machine cycle quit working properly on 3rd attempt. Bearings were replaced, tub was replaced and main board was replaced all before May 2015. Wash load constantly becomes unbalanced if more than 3 bath towels are in the load or more than 2 pairs of jeans. Can not start a load of wash and leave home because the machine will start bouncing and rocking when unbalanced and will shut down after it tries to self-balance 3 times. You end up with a load of twisted up, totally wet mangled clothes. Maytag refused to replace the machine and Home Depot continues to sell this junk to unsuspecting buyers. Wish I had looked at reviews before I bought this model. Worst $1,200 Ive ever spent. I have always bought Maytag appliances--refrig, stove, dishwasher, microwave, other washers--but Maytag has lost me as a customer after this experience with them. Terrible design and poor customer service for not standing behind their products.

A week after warranty expired, our 1 year old Maytag gas range (model# MGR7662WS 4) required new Direct Spark Ignitor (DSI) board. Knowing it was just beyond warranty, I inspected wiring first and found that the Bake connector on the DSI was loose, flopping around from a bad solder point on the board. Called Maytag and informed them of this manufacturers defect and all they offered was a $20 discount on a replacement part ($220 instead of $240). It worked with new part for 4 days, then something else went bad causing oven to spark, light, heat to less than 100 degrees, then shut down, then restart, then shut down, then restart, then stop doing anything. It has never worked correctly since then. How can a manufacturer of almost all domestic brands get away with such shoddy workmanship.. Taking advantage of defective or poor quality parts to sell more of the same when they fail and for an enormous markup? Where are the regulators who oversee monopolies and blatant scamming of American consumers?

I purchased a Maytag Washer & Dryer Bravos XL in 2013, the washer is already in the junk yard, the drive system failed, the bearings failed and it began to leak. The dryer had a main control board failed, I was able to purchase a new one and replace it myself. The board was made in China, the machines were assembled in Mexico. I replaced the washer with a heavy duty Speed Queen washer made in the USA!

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

Just like all the other reviews, 14 months after purchase and 2 months out of warranty the control panel on our Maytag Dishwasher stopped functioning. The “10 year warranty” is a joke a covers 3 things. We had model MDB4949SHX, $550 new.

I bought my Maytag Centennial washer & dryer about 2 yrs ago. It wasnt long after I bought the set, that the washer started having problems. I noticed the button to turn it on wouldnt go off. Then it was a pain in the ** to not be able to open the lid while the water was filling up. Something I havent noticed until today, its suppose to fill up to the amount of clothes that is in the washing machine. Well when I opened the lid there wasnt enough water in there to even cover all the clothes. Now I know why my clothes are not coming out clean!!! I am so frustrated with this machine and the company!!! DO NOT BUY THIS PRODUCT!!!!!

I purchased a Maytag made by Whirlpool in China about two years ago. The timer went out about nine months later. It went out again about 3 months after that and I paid to replace two sensors in addition. The washer still stops during a cycle at various times; it might be pausing or spinning or filling. When it finishes washing, sometimes it refills and leaves everything wet. I purchased from Deweys in San Clemente and they have tried to service but this is a real lemon. I will never buy anything again made by Whirlpool. I will research and find out what companies have been bought by them so as to avoid this. I note online that there are several hundred complaint problems about Whirlpool so they had to buy a company with a good reputation and ruin their product.

My over-stove microwave is approximately 18 months old. Suddenly, the fan came on and will not turn off. I had to unplug the microwave. This appliance is out of warranty but certainly should last longer than 18 months. I feel that Maytag should certainly be called to task for selling and promoting such a shoddy, unreliable product.

Bought this machine summer of 2018 when my old washer went out. This machine is impressive looking but that’s about it. Clothes don’t get clean. Half the time they don’t even get wet! I’ve had to wash sheets two or three times to get them clean and wet. When washing jeans there is always lint and white debris on them when the wash cycle is done. I’ve tried all different settings, I’ve tried different detergents always the same problem. Wish I’d never laid eyes on this model at Lowe’s last summer. Gotta say, worst purchase of an appliance I have ever made. Don’t waste your hard earned money on this piece of junk!

Maytag Frenchdoor MFX2570AEM3 - Was initially really excited with this brand new fridge. We have not even fully paid it off, as we bought with credit at Home Depot, and it continuously leaks water from freezer! I have taken everything out, defrosted, spent about two hours pushing hot water through the freezer drain with a turkey baster and it was only about four days before I had a puddle on my floor again! We have bought quite a few maytag products before, but after this fridge, probably never again! If there is a recall or a lawsuit pending, please, someone advise me of either.

I should have returned this machine after my first load of wash; it ruined a couple articles of clothing. Later it ripped a throw rug and just recently ruined a drapery panel. Is there any way I can exchange this machine and rid myself of it? SN: C22534900 Model: MVWC400XW4

I bought a Maytag Top Loader. I soon discovered that it is not possible to do a cold water wash. After much communication with Maytag Customer Service it was determined that there is no way to bypass it. And it uses a lot of hot water, even on a cold wash. Their explanation was that the water needed to be a certain temperature to make the detergent work effectively. The same detergent that I’ve been using for 40 years with cold water in my Speed Queen. When I need to do a cold water wash, I go to my parents home and use their washer. Disappointing purchase, my last Maytag, for sure.

I called. I was told nobody else ever had that problem. She hung up. I called again. The french door is nice to look at but it does not seal properly and there is CONSTANT build up of BLACK MOLD no matter how much cleaning. It returns. There is no other design for a seal either. There are several creases in the gaskets and there is mold in all of them no matter how deeply cleaned or sprayed. The seal is poorly constructed. DO NOT BUY THEIR FRENCH DOOR... Also their ice maker shoots ice all over the floor.

The first washer my husband and I ever purchased was a somewhat cheap top loader but it worked very well for over 10 years. We decided to fall for a bargain sale at Home Depot and went with the HE Bravos model. We were told that it would save us money and work great! From day one weve had issues. It never really seemed to clean right. It gets thrown off balance if you have more than one bath towel in a load at a time. After an angry call to the company and a somewhat helpful customer service rep, I began washing every load at the deep clean heavily soiled cycle and then did an extra rinse to boot. So much for energy efficient. So, fast forward 4 years, I HATE this washer but cant justify a new one at this time. Now, it stops mid cycle and I have to unplug it then plug it back in and restart it. When this happens, there is an awful smell. Needless to say, well be buying a new washer within a week or 2 and you can bet your life, it will NOT be a Maytag.

We purchased our Maytag dishwasher from Nebraska Furniture Mart in February 2013. The touch panel on our Maytag dishwasher quit working in December 2014, several lights would come on or flash or not work at all. The first repairman that we had come out took the panel apart, cleaned it up and put it back together ($100). It started working again but a few days later it started doing the same thing again. So I called the repairman back and he said the touch panel would need to be replaced. He called all over Omaha and no one had the part in stock. He called the Chicago Maytag warehouse and was told by them that they were out of them because there were so many defective dishwashers that they used them all. Now they are trying to find a new manufacturer to make them. It could be months before they get them in. So I contacted Maytag and of course they said that is not true and put me through to a parts company that they said has all the parts available. When I told that company that it was the touch panel, I was told by them that you only replace the touch panel for cosmetic reasons! So we got a second opinion from another Maytag repair company and he spent about 10 minutes looking at the dishwasher and said its a defective touch panel. He said he has replaced a lot of them in Maytag dishwashers. He recommended that I contact Maytag customer service and try to get them to pay for the part. I did call them and of course they refused because it is out of warranty. The supervisor even told me that they have not had any complaints about the touchpad malfunctioning! They do not stand behind their products anymore. I will never buy a Maytag or Whirlpool product ever again. I told them exactly how I felt and their only reply was Im sorry you feel that way. I am surprised they continue to stay in business. I dont understand how major stores can continue to sell their products when they are garbage. Based on the other reviews Ive read, Im not even sure we should fix this for $250.

DO NOT BUY MAYTAG REFRIGERATOR. I purchased a Maytag refrigerator 3 years ago, now it started to leak water on the floor. Repairman said this happens after about 3 years to all Maytag refrigerators because the water hose is too small and gets plugged which causes water to flow into bottom of freezer; 2 inches of ice on bottom of freezer. Now we have to remove everything from freezer and refrigerator, unplug for 2 days to melt ice so we lose all of our food in freezer and refrigerator.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

Our Maytag refrigerator is leaking water all over my kitchen floor to the point that my floor tile has lifted. The ref. is a French door with water and ice in the door and freezer on the bottom. We have been cleaning up puddles of water at least several times a day. I see that this is not an isolated problem, as others have complained about this defect doing the same thing with their Maytag refs. Why hasnt ConsumerAffairs demanded a recall on these expensive defective refrigerators to date? I am truly disgusted.

Great stove for the price. The oven bakes good, the self-cleaning oven is awesome, the top is easy to clean up and regulating the temperature is so easy.

Since the day the Neptune washer and dryer were installed, the washer has given me nothing but problems. It vibrates so badly and dances all over the floor.I have had the repairman over at least seven times and, now, it is out of warranty so I am spending my own money. The last service man was from Hurst Appliances in Regina, SK. He removed the pedestal to see if this might be the problem. He also sold me some foot pads for $50 that he said might help the problem. However the machine is still vibrating and the terrible mold smell comes out of it as well. I am thoroughly disappointed in this product. I will never buy another Maytag product and tell my friends not to as well.

Failed after only 13 months with light use. I have a Whirlpool extended warranty which I had to fight to get them to honor. Then someone came to fix my washer and needed part was ordered, but part isnt available and company wont tell me when it will be. I have received 6 part availability dates so far. Whirlpool wont help. Over two months now without a washer. Ive asked them to replace machine or give me my money back, but they refused. The Whirlpool Extended Warranty group doesnt answer their phones, was put on hold for a long period.

I just purchased a washer in April and the door is locked with my son brand new clothes is stuck in the machine in water, I called to get service and was told a date 2 weeks away, worst experience ever. Sorry ma’am is what I was told in a non caring way. I’m so furious if I could return this washer and dryer I would.

Maytag HE Top Loader Washing Machine: I have regretted buying this piece of garbage since my first wash. This washing machine is complete waste of money and a piece of garbage. The Auto Sensing doesnt work and doesnt cover the clothes with enough water. When the deep water wash is chosen the clothes just float around but the agitator doesnt get them clean. Dont waste your money hoping it will work, because it wont. Maytag used to signify quality that is no longer the case. I am going to also give a bad review to the place I purchased this piece of garbage because all stores need to discontinue selling this junk.

The machine had automatic fill which did not allow enough water to rinse the clothes properly. I had to run another cycle to rinse the clothes. The machine was also extremely loud. When I had a warranty repairman come out concerning these two item as it was brand new, I was told I should have researched better. I gave it away after 3 months.

We bought a top-loading Maytag washing machine in January 2020, and are very disappointed. Clothes do not come out clean. We called the Maytag call-center and were told that “high efficiency machines are different”. They use much less water to be green, but now I have to wash items several times, negating any energy conservation. This also takes more of my time. If we use the “deep water” option and power cycle, clothes are almost clean; however, it takes 1 hour and 45 minutes per cycle. My 18-year-old Whirlpool washed clothes beautifully in under 45 minutes. This brand-new Maytag is NOT an improvement. We use the correct HE detergent and have tried with warmer water, and all of the different cycles, but still do not get acceptable results. The Maytag washing machine is not effective at the one thing it is designed to do, clean clothes. Our specific model is MVWC565FW1, however the saleperson told us that all models are similar.

Shame on Maytag! Customer Service is appalling! Paid 2500 for one of their top of the line refrigerator/freezer and had the repair people 5 times in one year. It was determined that it is a bad model number that Maytag wont recall but knows it is faulty. Started with ice build up in freezer making it sound like a plane taking off. It kept running trying to defrost (energy efficient-right). The repairman put in a request to have the product replaced based on symptoms and freezer being at 26 degrees. We had to wait five business days for Maytag to review it. I have a family and was having guests. They told me to buy a dorm refrigerator and they would send me a small credit towards it in 4 to 6 weeks. They finally agreed to replace the known faulty model, but I have to wait for the exchange team to contact me (2 weeks later). I keep calling and leaving messages but cant get the exchange team to even return my calls. I have my sons graduation this weekend and I dont have a freezer and my refrigerator is faulty with all my vegetables rotting within two days. It also took two days to originally get someone in management to call me back (even though it did no good - she cant help me). You cannot talk to management if you call customer service. They downright refuse! What a company!

We purchased a Maytag refrigerator in 2009. The freezer is on the bottom. In the last 3 months weve had to defrost this frost-free refrigerator. The freezer frosts and the refrigerator went into the danger level for foods. A technician said there is a tube from the freezer to the refrigerator that gets blocked with ice and your food is spoiled in no time. I wish I would have read this website before I purchased a Maytag. Hopefully, this will help someone else. I thought that Maytag was a quality name. That was the good ole days and now Im living in the good ole days defrosting a frost-free refrigerator. Beware!

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

When we moved to a new home, we upgraded all the appliances, including the microwave. This was four years ago. When the first microwave stopped heating the food after two years, we thought it was a fluke and bought a brand new one, since fixing it would have cost more. Well, I should have gone with another brand. This is two Maytag microwave ovens in four years! We cannot believe that a company who enjoys such a good reputation can get away with such shoddy products!

Maytag Bravos washer MVWB750WQO frame assembly and cabinet rust - I sent letter of internal and external rust issues to Jeff Fettig (Whirlpool CEO) and received no response. Then, I sent letter a second time with an attached signed receipt. Then, I finally received a call from corporate staff member stating they would replace parts but not labor. Labor costs would cost between $350 - $500.00. This is without the initial service call and diagnosis cost between $100 - $125.00. The determined parts list cost would be $700 - 50% for Whirlpool internal cost + shipping be approximately $425.00. This is more than the cost of a new unit or the value of three-year depreciation value of the existing unit. This does not make any financial sense. Whirlpool should provide a new replacement unit at their costs. It has been three months and with no successful outcome. Also, via web research, there are many complaints about Maytag/Whirlpool and I am not the first in regards to rust issue. Therefore, Whirlpool is attempting to limit their financial exposure by only offering parts that they have to agree upon because the labor costs will not support this additional investment in a three-year unit. It makes more financial sense to purchase new or be offered a replacement unit.

Our Maytag dishwasher is a work horse. Never a problem just runs and runs. Could be a little quiet quieter. But does a t great job cleaning. I would definitely buy another one and would recommend it to any one.

We loved the YMMV4206 microwave - at first. After the warranty was over, we started having issues where we would put the food in the microwave and try to enter the time, wed get the message to open door and close door. Wed try that and for the next few months it would work. At the 18 month mark, thats all it would do, was tell us to open/close door. We ended up unplugging it and it has been unusable since before Christmas. When I call Maytag and related to the support staff our problem, they were of the attitude that it is out of warranty and we can send someone out to take a look at it - for $130 + HST without even repairing it, that would be to diagnose the problem that we already know, then we would have to wait for them to order the part and come back. Do Not Buy this product.

I purchased a brand new MHWE450WW01 Washer and MGDE500VW2 Dryer in February. The dryer takes forever to dry something; seriously, 3 hours for jeans! The washer sounded more like a jet engine taking off. I called Brothers Main, they sent a service person who identified right away that it was a known problem and he had over 6 repairs already, but be prepared to wait up to 3 months for the replacement parts. This is ridiculous. The service center, you can never get through to them and when you do, they dont seem to care. I had a 10-year old washer that made less noise than this brand new one that I spent $1800 for.

First front loader washer and love it. Saving on water, less tangling of clothes. So far they are quieter than others that I have had. The dryer is almost 10 years old and the washer less than a year. The machine I had previous to this was top loader that had to be replaced, would no longer spin.

The dishwasher (model number MDB7100AWW, serial number 158462977YH) that was replaced due to recall for fear of fire hazard has only lasted two years. Is there any recall on the recall? Our dishwasher was purchased in 2001. We live approximately 30 miles from the former location of Maytag manufacture, Newton, IA. In our 39 years of marriage, we have always had Maytag appliances: washer, dryer, fridge, and dishwasher with long lasting results. Our previous dishwasher lasted 23 years. It is very disappointing to feel the need to replace a Maytag appliance, which weve always felt was industry standard after such a relatively short life! It no longer fills correctly, and trouble has been diagnosed by service tech as bad control board. It seems theres a possibility of fire hazard once again. Can you offer any help short of replacing appliance as cost of repairs does not seem effective? Thank you in advance for your attention.

Maytag Bravos Washer 300 Quiet Series Model MVWB700VQ0 - Nothing about it is quiet. Worked pretty well the first year. Spin cycle works too well. It twists and rips. The second year it needed a new pump because a dime got into it and cracked the pump. When you wash anything bulky you better sit and watch it because it will almost certainly go off balance. Year three Sd (suds or slow) code started flashing and washer stopped half way through. Not sure why suds because I only use HE Tide, no perfumes or dyes due to my daughters sensitivity. I use Affresh as directed and on schedule. Was told it was a slow drain, found two dimes in the filter and a lot of lint. Still not working and flashing Sd... stops half way, agitator moves left to right doesnt spin. When the diagnostic was performed, the basket spun but when it stopped it made a grinding noise. Now it might be that it needs new bearings! So much for the Maytag reputation. Its junk and I will not be buying another Maytag, Whirlpool, Kenmore or any other product from their affiliates. Not purchasing anything from Sears again either. Also I will be canceling my subscription to Consumer Reports because they highly recommended this product. Shame on Maytag. How do we start a class action suit?

MDB4949SDM1 - After owning Maytag model MDB/C-2 for thirteen (13) plus years, I decided to purchase the subject Maytag Model when my 13 year old died. Big mistake. Previous model was very simplistic in rack design and it provided user-friendly options such as two detachable baskets for silverware and a special rack for delicate items.The new model has been designed so your dishes go in on angles on the top rack and as such bowls, small plates etc never stay in place once you move the rack and the lower rack configuration was redesigned and the rear area which was open to allow for bigger pots and pans to fit better has been removed, so now you have to lay your pans on top of the tines, very difficult to low the dishwasher.Additionally, I purchased the stainless steel model; apparently in the coating process a drip pattern was sealed that you can see when sunlight hits dishwasher. Further the stainless steel face that they bond to the door has popped, so when you grab the handle the face pops in and out. Lastly the new design has an adjustable upper rack; I tried numerous times to adjust the rack and couldnt so when I called Customer Service for these issues, it basically boils down to if the Service Man comes out and determines my issues are cosmetic and the rack which Ive never been able to adjust should happen to work then I have to pay the service call as there is not warranty coverage. So I declined the Service Call and advised that this would be my last Maytag purchase. I highly recommend anyone considering this unit fully investigate and test out before buying.

Neptune Washer: Tears clothes at random intervals and their help desk asks for money.

The whole Control Panel lights are turned off for several minutes. Then they return on. Frequency? Few times per day. Reason? We dont know. No water or ice are dispensed when this happens. No water pipe is kinked, water pressure is OK, no problem with cooling system and nothing happens with food inside refrigerator or freezer. There are no mention made in trouble-shooting section of customer manual. What should we do? In spite of this, we are satisfied with the product so far, after 3 years of use.

In 2011 I bought a brand new Maytag (HA!) washer & dryer thinking it was going to be as good as my old Maytag - which is STILL working since 1980 in a 4 person household! Boy what a HUGE mistake that was! In 2 yrs the bearings went out and something else - big! and would have cost more to fix than the NEW Speedqueen I got (which does a HELLUVA better job and by far all around is better than Maytag CRAP!) AND has a 3 yr warranty and not just 1 like JUNK Maytag! Maytag name went down the drain with the dirty laundry water! FOREVER! Seems the more I look around the more complaints I see! Whoever owns this brand now should be crawling under a rock somewhere and be ASHAMED of the POOR quality products youre putting out there!

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

MAYTAG REFRIGERATOR SAFETY ISSUE SHARP EDGE Maytag refrigerator model MRT118FFZ01 purchased Feb.2018. There is a safety issue, sharp edges. Maytag has been aware of this for over 1yr from customer reviews. I went to consumer affairs.com and there are numerous complaints on products/customer service. I have been asking for a replacement door since Feb. On Sept. 7th I cut the palm of my hand on sharp edge, drew blood, no stitches but I was very upset. Called Maytag, transferred to the safety dept. sent out service tech. He reported that it was a safety issue, very sharp edge, he had to put duct tape on corner to prevent any more injuries! He requested that new doors(freezer&refrigerator door) only be sent, I do not want/need the whole unit replaced. Freezer door has sharp edge also. I have numerous emails to/from corporate office begging since Feb. for a new doors so that this would not happen! Maytags solution is to buy back refrigerator or I should pick another model. Neither is a solution for me. I picked this model for a reason. I asked them to provide me with the simplest solution which is to contact factory where it is made, red flag it, talk to manager, quality control check to see that there are no sharp edges before it is shipped to me. They refuse to do that 1 simple common courtesy, customer service request! They cannot guarantee that door will come without a sharp edge! My model is not the only 1 with this problem. I talked to salesman & model in store has sharp edge & in the reviews the same model had sharp edge which was submitted over 1yr ago! So Maytag has been aware of this safety issue for some time now but chooses to do nothing about it! I chose Whirlpool because of the name, I thought it stood for quality & above all excellent customer service. Was I wrong, found that out thru numerous phone/email conversations. They just dont care! Is it too much to ask Maytag to give me a refrigerator with no safety issues?!!! I have talked to Aaron in the corporate office, he was no help at all. His # 866-817-5404 ext **. I have all the emails to/from him. Please help, I want this same refrigerator, only model that would work for me. Now that I have had personal injury & have spent so much time/effort, aggravation since Feb. trying to have them do the right thing I feel that I am due monetary compensation. Bottom line this complaint is concerning a safety issue & horrible customer service from the call center to corporate offices! The Maytag name isnt what it used to be known for, quality & service.

My Maytag 3000 series washer had to be worked on right after we purchased it. Now it stinks and is leaking. Repairs are going to be over 300 dollars. A part wore out. It should have lasted longer and why does the front loading washer stink. There is no door to open to clean the filter.

Bought this because it’s American made. It seems to be very glitchy. If you don’t use the detergent drawer it always flashes low detergent. The quick wash leaves soap on clothes. It acts up and leaves clothes too wet. No buzzer to tell you when it’s done. Have to hold button for 3 seconds to start. You can’t just hit button and walk away. Then wait for it to sense the load first to make sure it starts. Very expensive model.

I purchased a Maytag Dishwasher April 6th, 2011. Its only 3 years old and now the control panel isnt working properly. Specifically, the start button. Contacted Maytag Customer Care service and they could not help me other than charging $80.00 for the Maytag Man.. which by the way, we arent suppose to see because of their superb quality in appliances. So I have a repairman scheduled for next week. I am an highly dissatisfied customer because the dishwasher is used once a week for the 3 years Ive owned it. Just a poor quality product which I will never purchase again. Model #MDB7609AWB3 Serial # F10202246.

I purchased a Whirlpool oven. It is still under warranty at present. I used the self-clean oven feature just before Christmas, it wasnt that dirty but I wanted to have it clean for Christmas. The glass panels on the door had no stain or grease on it, until I used the self-clean feature, and now there is black staining inside the glass. This oven is not even 9 months old, and you cannot clean in between the glass. My second complaint which I believe is a very poor design on Whirlpool’s end is that the steam vents are very sharp. When I went to wipe off the black splash panel just under the vent tube, I cut my baby finger twice!!! And it is impossible not to slice your pinky. I have been working with Whirlpool since this happened, and they finally issued me a new stove. I was to go back to where I purchased this product and pick another stove. So I did this yesterday and checked out all the Whirlpool stoves because the store says I have to purchases a Whirlpool. But every Whirlpool model has the same sharp steam tube vent, and I am presently waiting for the store manager to speak with his higher ups to see if they will let me pick a stove made by a different supplier. I’m actually really shocked to learn that this could end up being a battle especially after I took the manager to every stove in his store made by Whirlpool and showed him each of the vents and just how sharp those vent tubes really are. You would think he would want to be aware of this and deal accordingly. So I post this to warn any potential customers of Whirlpool to check that steam vent on the left side of the stove, and stay away from it as it is very sharp and you can’t help but cut your pinky finger when you wipe across the stove.

Just so everyone knows, Maytag, Whirlpool, and Amana washers are all made by the same company and almost all of the internal parts are the same. The differences are mostly cosmetic, its just a way to sell more of the same thing to different classes of people. Just like Chrysler sells Chrysler, Plymouth and Dodge, they all had the same engines, transmissions and electrical systems, just different looks to appeal to different people. I found this out the hard way after purchasing an Amana front loader washer and dryer that broke down on me every other week for a year. I got tired of it and purchased the Maytag 2000 series. This set also breaks down on a regular basis! This is when I found out from the repair company that services these machines that all I did by getting rid of the Amana set and buying the Maytag set was buy a different looking set. Now I am really pissed. This company works for Whirlpool warranty servicing Whirlpool, Amana and Maytag as well as other major brands. All same machines inside the repair man said! Look into it, research it online and call whirlpool for yourselves as I did. You will find it to be true. So if you hate your Maytag, Whirlpool or Amana front loader washer or dryer, research and buy from a different company or you will buy the same old problems again and again.

In August of 2009, we had an opportunity to remodel our kitchen plus add new windows and doors. How exciting! SO we had put down new flooring in our kitchen that matched our oak cabinets and since we had a little money saved, we wanted to purchase new appliances to match. We purchased a Maytag side by side with ice and water in the door. It also had the fingerprint resistant stuff on the outside. It cost about $1300. You buy name brand so they will last a while but here we are November 12, 2014, 7 years later and the compressor goes out. If repaired, it will cost $8090 to fix. Why do I want another Maytag. I got a citation I bought in 1978 and it still runs. Hello Facebook, you will my next visitor.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

The only time one can get enough water into the washer to actually get ALL the items wet (or even damp) is to put it on BULKY sheets or HAND wash settings. That is true for any size load whether it be 1 item or 10 items. I prefer being able to get ALL the water I need first, then put in the clothes, then soap, but thats not allowed. First soap, then items, then a bit of water only after you close the lid. They like to say that the spinout dries them which is why they arent damp - but that is a lie when you can smell and see the dirt. I want my OLD STYLE back!

MTB2656DEB - Well my fridge is now about 12 years old and from the beginning it was horrible ice as always forming under freezer door. The cold cut draw broke 3 times with its cheap junkie plastic. I hated it from the beginning. I have owned a GE double door with ice maker for 26 years. Wish I had kept it.

Within 2 months of 1 year warranty running out, the control panel went wacky - does all kinds of weird things except work right. Called to see if there is any suggestions or work arounds and was told they would be glad to set up a service call for between $70 and $100, where they could tell me how much it would cost to fix. As with the other 100s of folks with the same problem, they basically said gee, you should have bought an extended warranty. If you have this many people with the same problem then it is Maytags problem, not the poor sucker consumer who got stuck with it. If you are considering this dishwasher, run, dont walk, as far from a Maytag or Westinghouse product as you can get. If anyone starts a class action suit against this product, please count us in!

Im really happy with my range. The only drawback is that the upper oven/broiler is a little on the small side. The five burners on top are convenient for when I am cooking a large family meal on weekends and holidays.

I purchased a Maytag dishwasher (Model MDB7809AWWI) in Sept. of 2009. In 2010 and 2011, it had dead control panels. The first time, it was under warranty. The second time, it was not, and I purchased a costly service plan to have it repaired. Now, 2012, its dead a third time. Maytag tried to tell me that I could purchase another plan for $289. I informed them that for that cost, I can replace it with a dishwasher that doesnt require costly service plans and yearly repairs. They informed me that their parts only have a 30-day warranty. If theyre not willing to stand behind their products enough to admit that one is faulty, then Im not willing to stand behind them as a company.

I purchased a new Maytag refrigerator on September 21, 2007. The refrigerator compressor went out on July 19, 2011, three years and ten months. The repairman said that the compressor developed a pin hole leak and all the freon leaked out. The repair cost appear to be around $300 when completed, hopefully. What a crappy refrigerator. It seems that this is a regular problem with all types of Maytag appliances. Maytag is no longer a premium appliance. Stay clear from purchasing one!

I purchased this washer because of Maytags reputation of the repairman who was supposed to be needed less. Ha! Was that a joke? Ive only had this washer 5 years, repaired once and now it sounds like its gonna blow up. Please dont buy one… Maytag has a one year warranty, but unfortunately I didnt take one out due to their reputation. Plus its hard on the working class to come up with the extra for the extended warranty! I dont normally write reviews but thought maybe I could save someone else a little cash!

I purchased a floor model Maytag Dishwasher from Abt electronics about a year and a half ago. 2 months ago, various light started flashing. Somehow I managed to get it going. Some blogs reported it might be a drainage problem. Others suggested pressing a certain sequence of buttons. After Each time I got it to work, it became harder the next. I bought Maytag because my old dishwasher lasted 13 years. What is interesting is that a company whose name Ive forgotten sent me bimonthly requests to purchase a warranty from them. Now they have stopped. I am a single mom of 3 with an unemployed ex. I work and support my family without any assistance. I count every penny. I cannot afford repairs nor a replacement now or any time soon. This is a travesty.My door says 10-year limited warranty and the delineates stainless steel tub and racks and chopper blade, but not the panel. I do not understand how Maytags denial of the problem and their unwillingness to correct the problem can improve their image. I will never purchase from Maytag or its associated companies ever again. What a scam! To be honest though, I have not contacted the company since it is not under warranty and all the blogs have relayed the same message: Maytag denies there is a problem.

MY MAYTAG WASHER and DRYER ARE 17 YEARS OLD. THEY are FRONT LOADERS WHICH I THINK MAKE A DIFFERENCE. I BOUGHT MAYTAG because I had trouble with Whirlpool products that didnt go the test of time. The only problem I have with my washer is the mildew.

I have had a Maytag Bravo Model MVWX500XW0. Bought less than 3 yrs ago for over $550. Four days ago, the drum would not turn during wash or spin. It would act like it was going to turn but then the door lock lid kept flashing. Today Maytag repairman came by and put in a new lock circuit. Instead of fixing the problem, it made it worse. The washer started making rapid clicking sounds and finally the lid lock stopped working altogether. The repairman could not get his computer to even do a diagnostic. Instead he calls his boss who says it must be the motherboard, a $300 part. My research indicates that Maytag almost always says replace motherboard and customers find that doesnt work either. Ive never had a washer last less than 10 years. Three years for a high-priced washer is mind boggling. Ive also never had a repairman make things worse by installing new part but that happened. I will never buy a Maytag product again, even if its owned by Whirlpool, which used to be a name you could count on.

We purchased this Maytag about ten years ago. We had an old brown one that had to be 25 yrs old and still going. This piece of junk has had two compressors; the ice machine hasnt worked in a year, and now it just went out again (third time weve lost hundreds in food)!!!! About the same time we bought a Woods freezer on the cheap, this freezer sits in the laundry room crap piled on it and around it and never have had a problem. Maytag = $2500.00 boat anchor.

I, too, have had major problems with this Maytag refrigerator! We have experienced everything from a malfunctioning ice maker, flashing control panel, overloaded compressor, erratic freezer (freezes much of the fridge contents), and doors not staying closed/inadvertently popping open. We have owned this fridge since 2007 and have repaired the ice maker and the freezing problems on our own dime. When the clicking sound woke the entire house up at 5 am, I finally decided to post! I realize that appliances are not perfect, and that Maytag had the best of intentions when designing and producing this product, but what really infuriates me is that Maytag has known about this widespread inherent problem since late 2006! Why no recall? Why no notice? Why no assistance? When I called the customer service line this morning, the representative acted like shed never even heard of this fridge having problems - yeah, right. All you have to do is Google the model number or just Maytag fridge panel flashing and clicking problem to discover thousands of similar complaints. I do not fault Maytag for manufacturing a less than perfect appliance, but I do hold them accountable for adequately repairing/replacing such a rampant and unsafe (compressor overload) product! Maybe it is time for a class action. Something needs to be done to protect the consumer from a company that is so slow to correct a long-standing and potentially dangerous problem!

Within the first month of purchasing my front loading Maytag Neptune washer (MAH6700AWW) at Home Depot, the soap dispenser fell off. The machine not only leaked, requiring stack of towels to be placed on the floor to keep the room from flooding, but often produced foul-smelling clothes, despite cleaning the machine. On top of that, the delicate cycle stopped working and then last month, the entire control board went! It is past its warranty period, and I cannot afford a new washer for my family of 6. The machine has been discontinued and the parts unattainable. The control board of our dryer (MDE6700AYW) went too, causing buzzing in the electrical connection and burning, causing us to have to shut down the circuits for the machine. Maytag has lost all my respect as a quality appliance supplier. We spent $1700 on the set and the machines have been a nightmare. Please note: we were NOT notified that there were class action suits against Maytag regarding their machines.

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

I suppose I am the lucky one in that the Maytag Bravos was given to me free. I took out a perfectly good Maytag standard agitator washing machine and replaced it with this several years old unit. What a mistake! I read the other reviews and see that I share the same problems. I always get a the oL fault as soon as it goes to do the final spin. So I have to reset and try again. Also I have seen the same kind of dirt on the clothing as others report. I dont know that I will waste my time contacting anyone about the fault code. I may just put the old one back in and scrap this thing!

I saw something on your website about Maytag Neptune class action suit back in late 2005. I have owned one, never was notified of the settlement, and saw this since I have a mildew problem also in my washer. They are not willing to do anything about the repair on my machine, but send out someone and make me pay for it. Since I bought it in 2002, I would want to know why was I not included in the repairs and why wont they honor me in this since I am the machines original owner. Help, I worry that I am not having clean clothes and it is contributing to illness due to mold spores!

I purchased this oven in April 2015. I have had nothing but problems with the unit. The temperature is off. I have had the probe replaced in July and will be done again next week (January 26, 2016). The AquaLift self-cleaning feature does not work. I ran the self-cleaning feature about 8 times and back to back on several occasions. The service providers stated that it really doesnt work and there is nothing they can do about it. The front of my oven, above the vent, is stained from the oven exhaust. They said there is nothing they can do about that either. The last service company that came out for a service call to check the oven temperature came without the proper tool to check the temperature and ended up snapping the propane line. I was given 6 month of a free extended warranty for my inconvenience and told that the company does not replace models. They will continue to come out and repair them. I will never buy another Maytag appliance again.

I have an MSD2542VEB01 model refrigerator purchased slightly over two years ago. I have the same problem as many others, which is the plastic breaking on the shelves. The first time, it was within a year and the part was under warranty. It is now a year and a half later and one is broken beyond use and another is cracking again. Maytag refuses to help me as there is no “recall and the plastic is not available separately from the easily removable glass of the shelf. The least expensive price that I can find for the shelf is $107 and I need two of them. $214 (plus shipping) when all I need is two pieces of plastic? Be very careful when selecting your appliances.

We upgraded and purchased a new Maytag Dishwasher Quiet Series 300 MDBH955AWQ to benefit our new kitchen remodel. Initially, the dishwasher worked great. I routinely insist on keeping the filters and interior clean as I was raised up believing that if you take care of your equipment, it will take care of you. Very shortly after purchase, there was a fire recall which was taken care of by Maytag and a third party contractor. Then as time went on, it continuously rendered out dishes with debris and food on them. Then it stopped working. It turned out the latch or door handle broke on the pivot point on the interior of the door. I got that replaced and everything was good again. Then about three months later, of course after warranty, it would not start or anything. I verified power and connections and nothing. I spent about $60 on JustAnswer for further advice and the answer was to replace the control board. After about $250 for a service call and $130 additional, it turned out the control board went out. I observed how it appeared to be a poor design due to the control board being exposed to all of the humidity and other moisture from within the dishwasher door. Then after that being fixed, about six months later, the door latch broke again. Its minor enough that you may not realize its broken until you open the door panel back up again. The plastic is breaking Im sure due to the heat and moisture, but its just minor enough that it will not make contact to indicate the door is closed. I got that replaced again for another $140. Four months of that getting fixed and Im getting the same result, no functionality at all from the control panel. In other words, the control board is out again!Ive spent almost as much in repairs that I have for the dishwasher in the first place. As many have stated before, why are we not getting quality products anymore? I went to the Maytag website to see if there were any other additional recalls for this dishwasher, and the recall site was down, so I called. The lady on the phone, as pleasant as she was, indicated that the recall for the heater coil was already performed, which I already knew. I asked, due to the other problems Ive had and money Ive spent, if there were any additional recalls, and of course the reply was no. Im used to staying with a reputable company and providing loyalty to that company for quality products and service, even if I have to spend more initially in order to spend less overall. Obviously, Maytag is now out of the question for future business or referrals. This dishwasher is getting replaced before I put one more dime into it.

We bought this he Maytag washing machine about 3 years ago. I have hated it from the start and should have put a review right away because it is a piece of cr#&. It does not save any energy because I have had to rewash loads because clothes come out still dirty, lint still on them, sometimes even dry spots on clothes. I did a wash today and chunks of HE detergent still in the clothes. I am rewashing a load right now. I now have to do a presoak hoping that will help the load come out cleaner. So dont waste any money on Maytags HE machines as I will never buy another one.Being an environmentally conscious person, I thought HE was the way to go but it doesnt save any energy when you have constantly run a laundry twice to get clothes clean. It also does not do a good job spinning as clothes are still very wet. I hate this machine and I am thinking about junking it even though it still runs. Very bad purchase.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

I have had it since 2011 and still works as good as it did back then. I love it. Hope it helps people decide when they go shopping for a dryer. I have a dog so I have to keep her clean so I wash a lot of her bedding and she sheds a lot. She also sleeps on the with me so that other bedding that I put for her on my bed between her clothes and mine which I do separate. The dryer works a lot and it is still going strong.

I purchased this washer from Lowe’s on 8/9/2017. After 3 years and 2 months, this washer would no longer power up. I tried resetting it by unplugging it and lifting lid 6 times. It didn’t work. The extended warranty from Lowe’s expired on 8/9/20. I called a technician and he found it need a control panel and control board. He suggested that I call Maytag to see if they would give me the parts as a courtesy since the washer was only three years old. I contacted them and experienced long wait times (51 minutes was the longest). I spent a total of 3 hours on the phone with them. They said no there was nothing they could do for me since the manufacturers warranty ended 2 years ago and the “mother control panel” doesn’t fall under 10-year motor warranty. Well, there’s no need for a motor warranty if there’s no power to the unit! The cost of the parts would be almost $600. It is shameful to not stand behind your product. I would expect to have to replace an iron or a juicer after 3 years, but not a washer. This was a major blow to how I would view the way they do business. I purchased the extended warranty from Lowe’s. I will never do that again. It was a waste of money. They didn’t make any concessions for me either. They kept saying it was a manufacturers issue.

My parents always bought Maytag and so did I. Ive experienced minimal problems in the past and have done my own repairs. My new MDB4949 dishwasher is GARBAGE! Imagine coming home and seeing water flowing out of the house under your back door! The water was coming from the kitchen across the kitchen floor and cascading down the stairs like a waterfall. I pressed the cancel button, nothing? Opened the door, NOTHING! Shut off the circuit breaker, NOTHING!Water continued to flow until I closed the supply valve! The dishwasher damaged my home! Six service visits later and still not fixed! 9 days out of warranty and still having the same problem! Customer service told me to hire a plumber to fix my plumbing problem with the dishwasher water supply! Thats funny because 3 other dishwashers (in the same exact place) had no problem with the water supply in the past 23 years? Two of them were Maytag!I never give less than a positive review but, this is outright FRAUD! The dishwasher has damaged my home on 2 occasions! Unless I want to stay home the whole time its running I cant use it? The customer service is pathetic at best. The control board issue is a scam by every company. Its all designed to keep you on a service plan and is a scam! Long gone are the days of the reliable rotary timer/control that lasted forever! You can thank everyone you know for not paying attention and letting this happen! I guess we can wash our own dishes by hand or comply with this obvious scam?

We love our Maytag Dishwasher! It's very durable, doesn't use a lot of water and really gets our dishes exceptionally clean. The best part is that it sterilizes on the final cycle! We've long trusted any Maytag appliance in our families for generations.

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!