Purchased a new stainless Maytag dishwasher model # MDB4949SDMO ser # F54240259 on 10-20-2015. Installed about three weeks after purchase. This unit is terrible -- has not properly operated or cleaned our dishes since installed. First service came shortly after install. Complaint was unit leaves white film on all dishes. (Soap used is cascade which was recommended by Maytag in owners manual.) Technician installed a new water fill valve because unit wasnt getting enough water. After that unit still no good as unit became noisier and noisier and still leaving white film on all dishes. Second service call: the technician indicated entire noisy pump assembly would have to be replaced and would need to order it. Third service call: the technician arrived and replaced entire pump assembly, taking the old one away with him. The technician said it will be good now. It wasnt, but at least it was quiet. That was in January 2016. This unit still does not clean dishes properly -- continues to leave a white film on everything requiring hand scrubbing to remove. All dishes are hand rinsed with hot water before loading them in dishwasher, but actually dishes are more dirty three hours later after the cleaning cycle has finished than before they were put in. After having to buy new glasses and plastic ware because stubborn white film will not come off and looks disgusting. Tried various different soaps and rinsing products to no avail.Finally contacted service department for the fourth time and today technician arrived and found the unit to be mechanically functioning as it should and can do no more to help. Said to try a product called lemi-shine. Maybe my water is too hard also he said, even though we are on city water! This is our third dishwasher at this home and have never had hard water associated issues. All I want is my full refund for this defective product and I only get the run around from Maytag. Stay away from this machine.

I purchased a Maytag Bravos XL Commercial Washer on Jan.31, 2020. I have had problems with the control board twice in less than two years. To replace the control board it cost $560 plus dollars. I may as well get another washer. So, I have to buy two washers in less than two years, but the next one will not be a Maytag. I will not recommend their products.

I had a Maytag washing machine replaced under warranty back in 2011 via Maytags Extended Service Plan. This took me several months to get done because of back and forth issues with Maytag not wanting to honor the replacement. Executive Support had to get involved after I wrote a complaint on this site. When they replaced this, they sent me forms to extend my warranty, which I did. They never changed the model or serial number so Ive been paying for 2 years now for an extended warranty on a machine I do not own.The new washer broke and I called in for service on 11/18/13. Active Appliance was sent out, said it was an easy fix but they needed to order a part. On 11/20/13 they contacted me to tell me I needed to speak to Maytag because my Model/Serial didnt match with my warranty records. I double-checked these and called Maytag Extended Service and was told that I would need to speak to sales at 866-730-6094. I spoke to someone named Lindsey there who told me that I would need to send a letter in to cancel my policy and request a refund for the 2 years Id been paying for a non-existent unit and that they could start a new policy for me and get a service order in without issue. My call was disconnected during this and when I called back, I was told to call back in the morning to get back to Lindsey because the office was closing and they couldnt do callbacks.I called back on 11/21/13 and spoke to Sam who verified that the letter was needed to cancel and refund but that I would have to pay for the repair to the washer myself and theyd tack on the cost of the new warranty onto that bill so Id be covered AFTER THE FACT. Because the unit wasnt covered under warranty, Id have to cover the costs myself and it had been MY responsibility, not theirs, to make sure that the correct model/serial was on the coverage.Maytag sent me the forms and I would expect them to have added the new information on it...not send me forms with my original washing machine information. Especially as this had been escalated to Executive Support and the person I dealt with there had gone over everything to make sure it all got handled in a satisfactory matter. So for now, Im waiting for a callback from the original rep, Lindsey, but Maytag tends to Stonewall and not return calls so Im dreading how long this entire process is going to take and cost.

MF12665XEM7 Maytag Fridge water runs on the floor: After reading the review and watching the video to fix, I called Maytag. They refused to help. We bought our fridge at Nebraska Furniture Mart. We have spent a lot of money with them too. My husband called to see if they would split the cost of the service call. They refused. My floor is ruined from the water leakage onto it when we are not home. We try to catch the ice buildup and remove it before it is an issue. Why is there no class action suit? There is definitely a problem with this fridge and Im seeing it online everywhere I look.

We 19 years and gently used. The door latch broke. We purchased a used quiet series Maytag dishwasher and found that the door latch failed on this. I recently found over 600 complaints for the same problem. If you are receiving this many complaints and its one of your most frequent complaint, do you think its time for a redesign of the door latch mechanic is??? Or are you relying on your reputation and dont care about quality anymore?This is it for Maytag. Im glad we didnt buy a new Maytag because we would be stuck again with a crappy door latch. If you cant be bothered with fixing your door latch issues and you know that you have a long term problem here, you at least can send a new door handle kit to those of us who are complaining. Of course you wont do that. And the only recourse I have as a consumer is to tell others about the ongoing problem with your front door latch on my social media. Sadly, you are now only another crappy dishwasher with no real quality control. I bought several appliances from you because of your reputation for appliances that last. Seems that is now a myth.

Our Maytag dryer is only, maybe, 3 years old. I do not dry towels, jeans or heavy sweatshirts in it (I line dry and then soften up in dryer). I clean the lint filter each time. Our heating element has gone for the second time. The first time it cost $200-250 to repair. It is so sad that our appliances are not made to last as they did. Or is it just Maytag? You can be sure we will not buy another Maytag item. I am looking into recalls at this time.

I love my new fridge! It has all the bells and whistles and looks/works great! My ice maker is the bomb! Best design Ive ever seen!

I bought my black refrigerator in 2006. It has ice in the door and freezer on left side and refrigerator on right. I have not had any problem with my refrigerator and it continues to serve me well. When I need to buy another one, I will probably get a stainless that doesnt show handprints.

Under class action suit in 8/2005, Maytag repaired my Neptune washer by replacing motor conversion kit. 6 yrs later the washer is having same problems as had originally; we asked Maytag just to replace the motor drive again ($190.00 part). They refuse, although this motor drive had identical life span to the one they replaced. It seems the replacement part was not new and improved, it only lasted as long as the original. Only now, we are past the class action suit deadline by years.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

My Maytag over the range microwave has given me nothing but troubles since my purchase. The turntable off feature never worked, and now the side control panel is barely hanging on because of broken plastic connectors. The handle is now broken in half. I will never purchase another Maytag product. Buyer beware.

Maytag 7000 series front loaders bought in 2013 on basis of high ratings from Consumer Reports. Also durable and look good in the process. Had for 3 years. Machines highly rated by Consumer Reports and bought on sale. They were a very good value. Both W & D have steam feature but find Ive rarely used it. Durability is key, as is the ability to balance wide variety of loads, which our machines do well. Capacity of 5 cu ft or better sufficient for a household of 2. Maytag reputation for durability and reliability and made in US, though a clone of Whirlpool. These are big, heavy machines, best for side by side but they can be stacked. The units are quiet, have more features than weve ever used and so far have been reliable, gentle on clothes incl delicates and drum bearings really help with keeping loads balanced. Door hinges built like a tank but the chassis theyre attached to arent up to par. W & D have stainless drums. Washer is resistant to mold & odors but dryer lint system convoluted in design and hard to clean out.

I purchased my Maytag Centennial Commercial Technology MVWC200XW in May 2012. This is the second time in almost 3 years that it breaks down. The basket decided to drop today and by the time I realized that it did, my whole bathroom had flooded, the water spread down the hall into my spare bedroom and soaked through the floor, also flooding my basement. I called customer service. They are sending a repair man next week, but as for all my ceramic tiles that are now cracked in my bathroom and my hardwood in the hall and bedroom that is full of water and are lifting off the ground. Its my responsibility to call my insurances to fix it. Yet it was their washing machine that caused the damage in the first place. When I purchased the washer I didnt expect to have to repair it every year. Not impressed! I do not recommend this washer.

3 years ago, we purchased all new Maytag appliances for our home. Within one year, we had issues with the top load refrigerator getting warm and the bottom load freezer getting extremely cold. After calling Maytag and getting horrible customer service (long wait on the phone, no supportive/suggestive advice, rude representative), we were given a phone number for a local Maytag repair man who charged $300 just to walk into the house.He was literally in and then out of our house within 10 minutes. His advice was to unplug and defrost the refrigerator for 24 hours. Thankfully, his suggestion worked, but should have been given to us as a troubleshooter by the representative on the phone with Maytag.We have had to unplug and defrost the refrigerator about every 3 weeks since. It has become very annoying and stressful. There is obviously a defect in the refrigerator that should be replaced by Maytag! I will never buy a Maytag product again.

I bought a Maytag washer and dryer in Cookeville TN. In 2018. After a year it quit. The service man from the authorized dealer in Cookeville could not repair it. After numerous calls Maytag sent a service man to repair it, this took about three weeks. This washer is a Maytag industrial, it has a 5 year parts and labor warranty, and 10 years on the motors. Now it is out again, after calling Maytag, and holding on the line for an hour, finally I had to chat with someone, and they set up an appointment for about 3 days. So service company call now and says it will be another week before they can sent someone to look at it, and another week to get the parts. They also questioned my warranty. I gave high dollar for this washer, what’s happened to Maytag?

Unsafe Maytag - We have had lousy service from our last purchase of a Maytag Atlantis washer and dryer. The washer failed after 14 months, and since it was more expensive to repair it, we replaced it. I needed to do a simple repair to the dryer today, and I had to take the front of the machine off. I found the inside too so full of lint. I believe it was only days away from catching fire. The blanket of lint I removed from the top of the heating element appeared to be charred and black, a fire ready to start in my opinion. I will not have this machine repaired. I want this fire trap out of my house. Before you ask, I must add, my wife cleaned the lint trap often. The Maytag Company has not been helpful. I will add that our first set of Maytags gave us many years of good dependable service. What happened to this company?

When we moved to a new home, we upgraded all the appliances, including the microwave. This was four years ago. When the first microwave stopped heating the food after two years, we thought it was a fluke and bought a brand new one, since fixing it would have cost more. Well, I should have gone with another brand. This is two Maytag microwave ovens in four years! We cannot believe that a company who enjoys such a good reputation can get away with such shoddy products!

My fiance bought this dishwasher 5 years ago but has never been able to use it due to the fact he is disabled and unable to open the door. When I moved in 4 months ago, I began using it regularly 2-3 times a week. Yesterday, I loaded it and when I hit the start button, it did nothing. The lights come on but the start button doesnt seem to be working. I have torn it apart twice and after looking all over the internet have determined that the control panel is bad. We live on a very fixed income and fixing something like this will take a large part of our budget. I am shocked that something so expensive can only last a few months then stop with no warning. We will be calling and adding our names to the list for the class action lawsuit here in California.

I purchased a Neptune front-load washer in November 2005. Now that its out of warranty, theres nothing that Whirlpool can do for me. The front panel of the washer that surrounds the door has been rattling for a few weeks, so my husband took it off and found a crack on the top right section of the panel where its bolted to the frame. There is a rust bubble where the crack started. We couldnt see any of this until he took it apart. The cost of a new front panel is $185 and the response from Whirlpool? They are “very sorry” that this has happened, but there is nothing that they can do. Oh, really? Well, I come from a long line of Maytag owners and there is something I can do: spread the word about the disgusting piece of junk I paid $1,100 for! This washer wasnt even made here - it was made in Korea and its not worth $100! Note to Whirlpool: your customer service sucks!

I purchased this washer January 2020. Bravos XL model# MVWB830DW5 is the worst washing machine ever. Does not clean your clothes, leaves soap residue on your clothes. Clothes aren’t fully submerged in water for the wash or rinse cycles. Do not waste your money. You will be highly disappointed.

Its just me and my wife. We bought a brand new, top of the line Maytag top loader washing machine 7 1/2 years ago. It quit working last week. We called a reputable appliance repair company in Toledo. It cost $88 for the technician to tell us the Maytag computer system is not worth repairing. It looks great. According to the technician Maytsg is known for selling junk. My wife and I felt we were buying a top of the line washing machine. We were duped. We had a top of the line LG top load washer delivered today. Never will we ever, under any circumstances, buy anything from Maytag.

We got our Maytag fridge approx.18 months ago. There was no trouble the first year and there has been nothing but trouble for the last five months. The freezer started frosting one day which causes temp to get in danger zone - we defrost it with a hair dryer about every week and it has continued to frost up ever since. We have a friend that works for a certified Maytag repair business. He came to our rescue five times and called Maytag hot line for help.Together, they could only suggest that the gasket be replaced. He could not see anything wrong with it but we changed it just in case. Still, the problem continues. When we called Maytag customer service (877-556-57420), we were told that no one has had the problem before us. We just looked online; there are 521 complaints about Maytag. My question now is, how do we get a class action lawsuit going?

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

DB7749SAM1 Maytag Stainless Steel Dishwasher worked great for 14 months then lights went crazy. My last machine was 30 years old before its motor died. I should have fixed it. Maytag needs to step up and fix this. I will make sure everyone knows from here on out, social media is a wonderful thing. I have not even used it that much - still looks brand new and this is unbelievable. I have seen so many bad reviews now on how Maytag has built poorly designed appliances and then to add insult to injury they will not fix their mistakes.

Purchased a Maytag dishwasher from Best Buy. We did not buy the extended warranty from BB because there is a warranty with Maytag. After 4 months of use the washer stopped working. We were unable to return it to Best Buy because we exceeded the 2 week return policy and needed to rely on Maytags 1 year warranty. It took over 2 weeks to schedule a repair and he was unable to fix it, it needed an entirely new Control Board and UI panel. 3 weeks later he returned with the new parts. It worked for 10 days with the NEW Board and panel, it has now stopped working again. We are not able to replace it due to the California Lemon Law which allows a company 3 opportunities to fix it before replacing. Next time I will purchase the Best Buy warranty so I can replace this Maytag LEMON.

Ive only had my Maytag Bravos XL Washer for two years and I HATE it. It constantly gets off balance during the rinse and spin cycle. What should take 30 minutes takes triple the amount of time. My washer is in the basement and I constantly have to run up and down the steps to readjust the clothes in the washer. Ive started to just stand by the washer now during the rinse and spin cycle. What a waste of time. I would not recommend this washer to anyone. Also, it does an awful job of rinsing out the detergent and softener. All of my dark colored pants have detergent and softener residue on them after they come out of the washer. Ridiculous!

We bought our Maytag Bravos in December 2010. Four months out of warranty, like many other complaints Ive read, we started getting the loud jet taking off noise from the laundry room. Now we are having issues with the lid lock not allowing you to get to the clothes. This machine tries to spin three times and then locks up. It literally locks the lid and will not allow you to get to your clothes! For a machine to fail just four months out of warranty is a joke! After investigating the problems with the machine, it will cost us more to repair than what we originally paid for the washer in the first place. Give me a break! There should be a recall and Maytag should have their feet held to the fire to replace these less than adequate high-dollar machines!

Within a year of purchasing this washing machine, I needed to schedule a repair service because the washer started making an unfamiliar noise. Repair Service shows up and refuses to touch my washer. The ink on the Serial and Model number (stick on label) inside the washing machine door has washed off. Sticker label in excellent shape, except all the ink has come off. If the Repair Serviceman cannot read the label, NO SERVICE FOR YOU. MY SAGA... Did you know that if your washer or dryer does not have a readable serial number on the machine, NO repair service will work on it. It does not matter if you have all the paperwork showing this information. If the original label is unreadable, no repair service will touch it because they will be fired. Maytag changes parts on a model all the time. The serial number is the ONLY way a serviceman can tell exactly what parts your washer was made with. Apparently the serial and model number label sticker was not printed with permanent ink. The Repair Service said the Serial and Model number ink washed off the label because the sticker was incorrectly put on the inside of the washer door at the bottom. But they were WRONG! Maytag shows online that is exactly where the serial and model number sticker is supposed to be located. So, I called Maytag to order a new serial number (stick on) label for our washer. I gave Maytag the information and I was told I would have the label in two weeks. Then I called back a week or so later to make sure the serial number was ordered and on the way. Maytag said there was a misunderstanding, and that they received my request on 6/17/15 and it was sent to the ONE AND ONLY GUY that makes replacement serial number tags and he was sent my request on 6/22/15. Maytag said it would take the one and only man quite some time to make the label (SINCE THERE IS ONLY ONE!!!) and I could expect to receive the replacement label in 4 to 6 weeks and they were sorry, but there was absolutely NOTHING they could do about it. So as my year old washer sits for over a month, Im going to the Laundromat each week. We should have received the new serial number on August 6, 2015. So it’s taken almost 2 months and my label is close to two weeks late. To date I have not received my serial number. I tried to use MAYTAG chat, dont bother, they said they couldnt help me. I needed to call in. So I emailed Maytag today for their support services to tell me WHEN I can expect to receive my new serial number label. I bought this through hhGregg. Check your Maytag washer. IF THE SERIAL NUMBER AND MODEL NUMBER LABEL ARE INSIDE THE DOOR, CHECK TO SEE IF THE INK IS COMING OFF THE MACHINE LABEL, and order a new one NOW if it is, or you will not be able to get your washer serviced. Do not put new label back on the inside of the washer door. This is just unbelievable.

We purchased a Maytag MVWX655DW1 Bravos MCT washer in 2017 and I recall a sloshing sound during agitation. Its a high efficiency model and was okay for several months, I think. It began to make something of a clunking sound during agitation that was similar to the deceleration sounds when the spin cycle completes. It seems that is an indication that something is wrong. Clothes arent clean after washing - another reason to suspect a problem. I observed the wash cycles and noticed that some items dont even get wet during the wash cycle. The clunking is probably an indication of the type of failure but I couldnt find anything other than someone else asking the same question when I did an internet search. Expected performance is shown in a company video with water sloshing during agitation. Thats the key take-away. My basket moves back and forth an inch or two during agitation and makes a clunking sound at each direction change. Water isnt sloshing through clothing and some of the garage rags that were once my clothes probably just needed a good washing. I suppose that even cleaning the washer isnt accomplishing much. The spin cycle is actually impressive. I load the washer evenly and find the completed loads with a towel or shirt evenly covering the clothes pulled to the basket below. Unfortunately, thats probably the only part of the process cleaning anything.The enclosure says its designed and assembled in U.S.A. and, unfortunately, speaks to our manufacturing ability. Some of the engineers Ive worked with over the years suggested areas to inspect. I was able to use my phone camera to look under the unit and noted that it is controlled by a main drive motor and a little synchronous motor with a linkage that Im guessing changes agitation direction. Both are made in China. Ive considered repairing it and just pulled the wash plate for inspection and found nothing beyond the difficulty of pulling the wash plate. Probably an issue with the drive assembly and a few hundred dollars in parts to fix. Ive also had input from someone about the cost of replacing the control board. I grew up with TV commercials of the Maytag repairman with nothing to repair in the world of reliable, American products. Its disappointing to find that is no longer the case. The low tech GE washers weve used all our lives were old and ugly when they left our house. Not defective, a few drops of oil below or worn finish but still working. It really is a disappointment to look at where we are today. It didnt have to collect samples on Mars or deliver orders in a self-driving vehicle. A reliable washer to clean dirty clothes is all we hoped for.

Maytag Centurian is a terrible product. I dont think the designers of this model have ever washed and dried a load of clothes. Washer problems: The lid (top loading) locks so user unable to determine if the correct amount of detergent is being used. There is an unlock button, but it takes quite a long time to unlock (maybe 15 seconds), then an even longer time (seems like a minute or 2 to restart). The machine is LOUD and at one point in the cycle BANGS. I actually returned the first as defective, but when the 2nd machine made the same noise, I was told, no, thats the way it is. It seems to take much longer to wash a load than my previous machine. The Power Wash tears my clothes. Even the regular wash puts holes in my thin tee shirts after a few washes. Really had to get spots out. I almost have to hand wash to get the spots out BEFORE putting in the machine. Dryer Problems: Takes 70 minutes or more to dry a normal load with a couple of towels. The cover to the lint catcher doesnt seem to be properly sealed. Lint particles get all over the top of my dryer. I bought this Washer/Dryer combo last year. Im annoyed every time I do laundry.

I love the functionality of this Maytag refrigerator. The inside is so nice and big, I can almost fit anything into it. When I need to make a lot of food for a lot of people, this refrigerator really foots the bill.

We had a Neptune Maytag for over 12 years, best machine ever but this one (Bravos XL) is complete junk. We have been very disappointed in its ability to clean clothes with the length of time to complete its cycles is ridiculous. Its always out of balance with just a few pieces and lack of water twisting everything in knots. Well 16 months after purchase here we are with a broken machine, we have a fried circuit board. Maytag has lost our business permanently.

First failed after 16 months. Second twice in 15 months. They are lucky to last 16-24 months. Stupid for a microwave that normally last 5 plus years for every other brand I ever bought.

Well I must say I concur with all previous posts. I just replaced my Bravos with a Samsung after my jet plane of a washer died. My repair guy said it was not worth it to fix it. I had already replaced the shocks two years ago but I did have mine for 8 years. I have had the same problems as previous posts - rust, smell, holes, broken, too expensive! Hello to Samsung!!

PURCHASED WASHER FROM LOWES. IT STOPPED WORKING IN 2 WEEKS. CALLED MAYTAG FOR SERVICE. First repair service wanted to charge me. Next repair company Rawlings made 2 visits, looked at washer 1st visit said they had to order top latch. 2nd visit need circuit board. 3 weeks passed no latch, no circuit board, nor repair service. DO NOT BUY A MAYTAG WASHER.

Bought new Maytag French Door with cooling drawer refrigerator in July, & have had nothing but problems with both product & customer service since. Have already had 2 service calls for the SAME problem. The in-door ice maker/dispenser is a horrendous mess. Place a container below the opening to get ice cubes & ice is sprayed in chunks all over the floor & around the kitchen. To get ice, you have to put the container in direct contact with the opening, & then place a towel over the entire in-door unit to keep ice chunks from spraying all over the floor. The unit has a small flap-door in the ice maker, which must open & close automatically when getting ice, but the flap failed to close, so the ice in the ice maker was melting & the water running into the refrigerator unit & onto the floor. Called warranty repair & they came out & said they fixed the door-flap, but they did not. Ice was still melting & the freezer unit would not even keep ice cream & pastry items frozen solid. Called repair a 2nd time during the first 4 months of ownership, & they came out & replaced the motor to the small door-flap in the in-door ice/water unit. When asked why the freezer would not keep ice cream & pastry items frozen solid, the repairman stated (quote): Freezers dont keep ice cream frozen solid because it has so much sugar in it, its like alcohol. Had no excuse about the pastry issue however. We replaced a 12-year-old Jenn-Air with this piece of junk, but at least the Jenn-Air kept ice & ice cream frozen solid, & the ice maker did not leak & spray ice around the kitchen. Jenn-Air must know something about freezing sugary ice cream, that Maytag/Whirlpool do not understand. Then today we got a notice that Whirlpool had denied payment for the 1st repair visit, even though the unit was only 2 months old then. As such, we expect them to deny payment for this 2nd visit, even though the unit is now only 4 months old. Bad product & sloppy customer service, from a company with ZERO consumer support.

The oven hasn’t caused any issues. It’s beautiful stainless steel and black finish creates a shiny but modest finish to my kitchen. It’s self cleaning power is also useful and saves time and where I come from time is money. It cooks food evenly just as an oven should.

It doesnt clean as well as the cheap GE model we have at our beach cottage. Also it is very noisy. Disappointing. Will never buy a Maytag dishwasher again.

MER8700DH - Within 6 months, left rear burner stopped working and Maytag repaired it under warranty. Within next 6 months, and just before end of warranty, right front burner stopped working and again Maytag covered it under warranty. Within the second year of ownership, the oven was not working correctly and Maytag refused to cover it because it was off warranty. So I called a local appliance repair company who gave me an estimate of over $300 to repair it and basically advised against repair stating that this stove was a piece of junk. So I replaced it with a GE and junked the old one before it was even two years old. I filed a complaint with Maytag. At first they said they would go half on the labor, but then they said I should have bought the extended warranty and refused all further help.

In December 2017 I bought a Maytag Bravos (w/o agitator) based solely on past experience (56 yrs.) of buying from Maytag without any complaints. A friend told me I wouldnt be happy with my purchase and she was RIGHT! It doesnt get my clothes clean to my satisfaction, my towels are all getting snags as well as silky sheets and pillowcases and dark clothes have a soap scum line on them. I have slightly better luck if I wash everything with the deep water level option but I still need to wash dark clothes a second time without any soap or fabric softener to lighten the scum line.I am very careful to use minimal amounts of high efficiency detergent but that doesnt help. I called Maytag and complained within the first month but then we were gone for the month of February and I just never followed up with them. Now Im sure its too late to do anything. I wish I had listened to my friend. Hopefully I can save another consumer from making the same mistake I made.

We bought the Maytag 2000 series washer and dryer stackable set in 2012 from Home Depot. My husband was smart enough to buy an extended warranty and year after year we renewed it. Guess what?? Year after year the dang washer broke. This machine was a nightmare! Now that the drum spider is broken they will not honor our warranty but want to give us $300 and guess what? I cant find a replacement for my good working dryer. We bought this set because we live in tiny space and needed them stacked. Maytag really put us in a corner and we have no money to replace both appliances. Horrible customer service. Horrible machines. Just a horrible situation. We dont know what to do.

Everything in my house is Maytag. I assumed they were the best. My dishwasher went out after three years, and I replaced it with a Maytag. Now, my over the range microwave is not working. I will not replace it with Maytag. I expect my washer and dryer to be next.

I purchased my Maytag Bravos washer and dryer in July 2007. As with any appliance, we always purchase the extended warranty as it usually runs about $100 on appliance. My first experience with problems was in February 2010 when the control panel went out. If I had not purchased the extended warranty, I would have been in trouble. It ran out in July 2008. It was downhill from there. In September 2010, it quit spinning; and the fabric dispenser would not work. I called again in September 2010. The tub was out of balance. In June 2011, the panel control went out again. In November 2011, it would not spin. In June 2012, the panel for control had to be changed out again. In July 2012, now the pump is leaking. And guess what, my extended warranty is up 8/1/2012. I contacted Customer Service, which said unless there was the same problem within 12 months, there was nothing they could do. Well, Im fired up. I intend on making a complaint with the Better Business Bureau and anyone else who will listen to me. I paid over $2000 for the washer and dryer, and it should last more than 5 years. This is ridiculous! When Whirlpool bought out Maytag, then the product went to crap! Dont tell me the Maytag repairman does not have anything to do now, because I know I keep him real busy. I am so tired of the companys just blowing you off when you work hard for your money and purchase a product for your family that should last at least 10 years. I am a principled person, and this is not going to go away easy. The repairman is coming next week to fix it again. I am going to give him an earful as well. The last one who came to change out the panel board (3rd time) said they had nothing but problems with this unit. Well maybe they made it that way, so when the warranty runs out, they can charge you an arm and a leg for the part and the labor to repair. I will never buy a Maytag product ever again. My next one will be the new LG washer and dryer. Talk about the lemon law. This product from what I am reading here should very well fall within that category.

My Maytag (MER7662XQ) oven has stopped working after barely 6 months of use. I filed a warranty-repair complaint and reported the error codes shown: F1 (faulty touchpad) and F3 (faulty temp sensor). Although Maytag promptly sent a repairman, he arrived without parts and left within 5 minutes without fixing anything. He said he would order parts. Whenever they were delivered to us, by mail, we should call again to schedule another repair. But he warned he was prohibited from coming out for another 7 days. So far, Ive been without an oven for almost 3 weeks and there has been no action or information. My calls to Maytag produced nothing, except confirmation they show the repair as open since they do not actually distribute parts, and the repairman is with an outside company. A terrible product and a worse service! I would not ever buy another Maytag product and recommend that no one else does either.

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

I bought a high capacity Maytag Bravos washing machine, thinking it would be better than the ones that shred your clothes around the center post. Wrong. You still have to wrap your clothes around the edges as if there were a post, and even then the machine will become unbalanced (after much thumping and crashing), causing it to stop, which forces you to redistribute the weight, sometimes several times in one load of wash! I called the company and got nowhere -- I wont say nowhere fast because it took forever to get nowhere. I do not recommend this machine.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

I paid over $600.00 for a new maytag washing machine two years ago. It quit working a few days ago and the man said itll cost over $400.00 to fix it. Why do you people build this type of junk? I would like to hear from someone on this and why I had to pay $300.00 a year for a washer that is totally worthless now??????? ** please contact me. This is crazy to buy this washer and it only last two years.

Bought brand new Maytag dishwasher. Worked great for 3 years. Then caught on fire. Couldnt contact maytag for a month because when you call your on hold for 30 minutes. Then when I do contact them they will only want to give 50%off another of their products that Ive already had catch on fire. I will never buy another one ever.

Maytag ser5000 washing machine from hell. When called the customer-service stated over the phone there is bearing problem. When the service-man show up, took one look (approx 50 seconds) at the washing machine (which only 4yrs old), stated he is not touching it and not worth to fix it - get this! Due to bearing! Charged me $200 as standard fee. To put salt on the wound, service-name stated: Ive should told the customer-service bearing problem which is very well known by Maytag! Therefore, save my $200. Note, I will NEVER buy Maytag appliances!!!

This Maytag refrigerator is a counter depth so a little smaller in the Inside than I would like but fits in my tiny kitchen great. It has an inside water dispenser which is so nice because it keeps the clean look on the outside. It’s a year old and so far I have not had any problems with it.

The whole Control Panel lights are turned off for several minutes. Then they return on. Frequency? Few times per day. Reason? We dont know. No water or ice are dispensed when this happens. No water pipe is kinked, water pressure is OK, no problem with cooling system and nothing happens with food inside refrigerator or freezer. There are no mention made in trouble-shooting section of customer manual. What should we do? In spite of this, we are satisfied with the product so far, after 3 years of use.

I dislike Sears and more so Maytag. I bought a Maytag Bravo XL MCT. It worked nice with very few hiccups until 1 1/2 years old. Then the washer went to the lock and done mode, thought it might be the lid switch down the washer up. Looks like I would need to change out the whole panel. Its not worth the trouble OR time to put one dollar to repair the piece of **.

I just purchased a washer in April and the door is locked with my son brand new clothes is stuck in the machine in water, I called to get service and was told a date 2 weeks away, worst experience ever. Sorry ma’am is what I was told in a non caring way. I’m so furious if I could return this washer and dryer I would.

I purchased the Maytag Bravos top load washer and the matching dryer at Home Depot back in 2009 after giving my son my very old Maytag washer and dryer that was running just fine. I liked the top load energy efficiency idea of the new Bravos and the large capacity of both the washer and dryer. Also, the Maytag name sold me, gave me confidence I was purchasing a quality product... WRONG. When it was delivered, there was damage to the dryer door, so a new one was ordered and mailed directly to me. Once it came in, I called to have someone come put it on. First issue, not a really big deal but disappointing.About one month into using the dryer, the top of it became so hot it could literally burn your hand. There was also an error message. I had purchased a one-year warranty, even though technically there is a manufacturers warranty on the product. A part had to be replaced in the panel. This happened twice. We then moved out of state for one year and the washer and dryer stayed in storage unused during that time.Fast forward to 2014 and the washer will not complete any cycle except the spin cycle. I keep getting an error message of OL which means overload. The machine is NOT overloaded. It literally takes me hours to get through one cycle of washing clothes. And they dont even come out clean. I called Maytag repair and they offered me a one-year warranty for $363.75 since the washer is having issues. They explained to me if its the control panel the cost alone for that is $383.00 not including labor. Also, the dryer take forever to dry. I have to run each load through a cycle twice to dry everything. So much for the energy efficiency of these machines. At this point, I am considering just buying another washer, something cheaper without all the fancy bells and whistles. I am terribly disappointed in Maytag.

Purchased washer less than 2 years ago. Loud noise like a jet engine or helicopter in spin cycle. Did not purchase the extended warranty. Called Whirlpool/ Maytag customer service. Was told I could have one of their repair people come out. I would have to pay $300 which would give me the repair and extended 1 yr warranty, or I could get $300 off toward a purchase of a new washer. Are you kidding me? This washer wasnt even 2 yr old and making this horrid noise in the spin cycle. I had to have a independent repairman for Maytag washers come out to tell me it wash the bearing and would cost 3 to 4 hundred dollars to fix it. I said no thanks and after his $90 service call am stuck listening to this piece of junk make noise till it completely breaks. I will never buy a Whirlpool product again or recommend one. Whirlpool you sell nothing but junk.

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

In reading the reviews of a Maytag Dishwasher, I am also frustrated in the dishwasher is only 3 years old and the start button does not work. It cost $75.00 for the repair person to come in to take a look at it which they deduct from the cost, total repair cost $300.00. Did not make sense at this time to have to pay the $75.00 repair person and then purchase another $500.00 dishwasher so paid the total $300.00 hoping to get a few more years out of Maytag dishwasher. By the other reviews, may not be possible. Just very frustrating.

I am angry at my Maytag! It sprays water on clothes that is not enough to soak them or let the detergent to be dissolved especially for towels. Hopelessly, I Hand Wash my towels, rinse in tub then just put them in the machine to spin. BAD BAD :( :( Is it possible to increase the water amount?

I bought a Maytag dishwasher in April 2012. The electronic control panel failed in October 2013. Repair quote was $250, and there is no guarantee that the new control panel will not suffer the same consequences. My research has revealed that this is a very common problem with the dishwasher experienced by a large amount of owners, all about at the 18-month mark. I contacted the company and was chastised for not purchasing the extended warranty and was basically told, Too bad so sad. Buyer beware, do your research before you purchase this appliance. I will never buy a Maytag appliance, or any brand associated with the Maytag name.

less than 2 yrs old and has completely failed to operate. We have been patient with this model. It does roll the clothes to point they are wrapped around and among each other and must be pulled apart before placing in dryer. The wash cycle now takes more than 45 minutes, It fails to spin the load often. Now, it has failed to the point it will not operate with or without any clothes in it.

I bought the Maytag Bravo XL washer and dryer several years ago after reading many reviews. I like the glass top of the washing machine and the front door glass on the dryer. The dryer is fine its the washing machine that does not perform like the old machines. Whoever came up with the bright idea of saving water by cutting down the volume in your machine to about 6 inches for a good size load probably have never used a washing machine in their life. It does not get your clothes clean and does not get the soap out of a clothing to my satisfaction. Who made this suggestion? Could it be the same branch of government that made everybody use those spiral light bulbs years ago? The fluorescence that give off loads of EMF?

The microwave does everything I need and want it to do perfectly. It has never needed to be repaired or replaced in five years. We bought it on sale from Best Buy and consider it one of the best bargains we have ever made. Easy to operate, easy to clean, sleek and, for an appliance, quite personable. I find it refreshing to say something nice about an inanimate object.

My only issue is that I am short and find it difficult to reach the wet clothes to put them in the dryer. Other than that I am quite happy with the machine. I have had no problems to date. Thank you.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

We have had Maytag washers in the past, and they always worked well and were reliable. Not so with the Bravos washing machine. It is by far the worst excuse for a washing machine weve ever used. It does NOT clean clothes. It merely ingrains the dirt more into fabric. In four years, we have complained repeatedly to Maytag to try and get some kind of remedy to no avail. Maytag is simply not interested in standing behind their product. So now, after two generations, they have lost us as customers forever and we are telling anyone who will listen; DO NOT BUY A MAYTAG WASHER. They are terrible and not what they once were.

I have a top loader Maytag washing machine, Model MVWB835DW4, bought in 11/2019. Five months of light use, the lid cracked. Received a replacement and four months later the lid once again cracked in the exact same spot. Requested replacement parts under warranty and I was told that a service tech must install the lid. Due to health and safety concerns related to Covid, we are not take any chances letting people into our home. My wife and I are 70 years old and are at high risk. Maytags response was they would not send parts under warranty to me and a service tech must install the parts. If I dont let them in by 11/2/2020 (the end of the warranty period) then I would have to pay for the parts. Maytag has the very worse customer service in the industry.

Four years ago we upgraded our 20+ year old Maytag washer and dryer to go with a more water efficient model. The old units were working like champs so we upgraded with Maytag assuming it to be equal quality. From the beginning we were not pleased with the washers cleaning ability and now we have electrical problems and a leaking transmission. Our serviceman estimated repairs to be the cost of a new washer. (Im not talking about a Maytag for replacement.) I e-mailed the Maytag company and they basically said Too Bad. Totally disappointed!! Wish we had our old units back.

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

Washer Leaks, dryer noisy, cant balance washer, dry settings make little economical savings. Washer repair list, balance adjustment, filter body, door latch, door casket. Dryer lint basket felt repair. Door sensor, overall un-dependable.

Maytag Model #MGR7662 range - We inherited this oven when we bought my mother-in-laws house 2 years ago. We had to get a thermometer to keep in the oven since the temperature is never consistent and is usually 50-100 degrees lower than the digital readout. We will be replacing this oven as soon as we can and it will NOT be a Maytag.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

We purchased a Maytag Bravos Quiet 300 about 8 months ago and it will not clean anything. Not one setting will make this machine clean. You have to wash everything 2 to 3 times. There is no savings of any kind with this machine and I dont know anyone who has the time to wash everything multiple times. Its all about the water; its about as much as you can spit. I ran a hose from the faucet and added 8 gallons about 10 minutes into the wash cycle and was able to clean (float) a set of sheets. I find this energy star machine to be worthless and I would have been better buying an old machine at a garage sale than this Bravos machine. Junk. If you cant float your cloths folks, you might as well be rubbing them on a rock.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in 2014. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within warranty. Then another valve got stuck about a year ago and the third one got stuck about a month ago. I am going to replace these two valves now. My friend, who is helping me replace, has similar gas range. He also needs to replace a valve. His range is about a year old.

Maytag Washer over 3 years old. Often problematic not functioning smoothly! Maytag invented this defective machine to intentionally rob the customer with all the probs that comes with it - poor design & quality, & not logistically programmed! Even aftercare/customer service SUCKS!!! Now, sensor spinning option is no longer working, drum not operational. No more Maytag!!!

My Maytag dishwasher is a nightmare. I purchased it in February 2013, started having problems with it turning off a week ago. I called Maytag customer service on Wednesday and was told I had a service call scheduled for Friday. I took the day off of work to be available for the repair service. I was given a phone number for the repair service. By noon I was wondering when I would receive a phone call to let me know when the technician would arrive? Then I was told that my appointment was scheduled for next Tuesday... ARE YOU KIDDING???? THAT WOMEN FROM MAYTAG CUSTOMER SERVICE LIED TO ME ABOUT THE DATE OF SERVICE!!!! I spoke with Scott, customer service representative (manager) and he told me that I was sent an email with confirmation. ANOTHER LIE!!!! I HAVE NOT RECEIVED ANY EMAIL FROM MAYTAG. I would never buy another Maytag appliance.... They DO NOT STAND BEHIND THEIR PRODUCTS. LOUSY CUSTOMER SERVICE... SUB PAR TO SAY THE LEAST!!! Very dissatisfied customer - wasted my time and are not willing to make it right.

I bought a Maytag Refrigerator (Model No. MFT2672AEM10; Serial No. K31503192) on 05/13/2013 at LOWES. On 07/27/2013 my son got hospitalized due to some kind of infection. He had fever and diarrhea that didnt go away. We didnt know what caused it. When my wife was cleaning the refrigerator, she noticed that the ice bin container had a rusty screw and metal plate. Why is the ice bin screw/metal plate rusting? We informed Maytag about this issue and they replaced the ice bin. Now, the replacement ice bin is rusty again. I sent an e-mail to the Maytag Customer Service Manager on 04/20/2015 and was told that its no longer covered by the warranty. I informed the manager that this is a defective/flawed design/rusting part from the beginning and Maytag should have REDESIGNED it when I informed them first hand and not just replaced it with the same defective/flawed/rusting part. I told the manager that this is a safety concern and Maytag needs to do something about it. The Customer Service Manager I talked to didnt want to do anything about it.

The control (computer) stopped working. The Maytag Centennial washer would not turn off. I had to unplug it from the electrical outlet to get it to stop. The repairman had to replace the computer panel. He said it had burned up. I bought this machine from Lowes on January 11, 2011. It lasted 15 months and cost me $265 to get it repaired. I called Lowes and because I did not buy the extended warranty, they would not even talk to me. When I pay about $500 for a washing machine, I expect it to last longer than 15 months! I will never buy another Maytag appliance! Customers beware: these products are a bunch of junk. Even the repairman told me so.

Maytag Maxima 9000 washer not working since day 1: I have placed a call on Friday, June 14, about my Maytag washer not working. The service man came in on Friday, June 15, 2012, and stated that a UI board needs to be replaced. I have called Whirlpool to ask for the part to be ordered so it is faster, could not do anything. Then, I have not heard from Whirlpool since. I called them again on Wednesday, June 20th, and I was told that the part was ordered and it will take up to 10 days for it to arrive. Once it arrives, the technician will call to set up an appointment. So, according to Maytag (Whirlpool), I can be without a washer for at least 2 weeks (as 10 days are 10 business days) and it is all good.

Purchased a Maytag Centennial Washer from Lowes. This is the NOISIEST WASHER I HAVE EVER HAD. Self Balancing, pretty much the way it is, YOU lift that heavy wet laundry and re-arrange to balance. It just slams around even moving the washer, until you do. This washer also doubles as a BLENDER. It SHREDS laundry. The agitator does not go all the way down and thus, clothing, towels, rugs... get stuck under the agitator, wind around and RIP. Have had hundreds of dollars worth of laundry shredded such as: shirts, towels, new rugs and it even ripped the waist off a pair of my jeans! The other laundry gets tied up on the stuck laundry and you end up with a twisted, ripped, tied up Laundry Ball. It will not wash or rinse well when it does this, naturally. Lowes: The salesman knew about all this, and sold it anyway! He had one and got rid of it. Gee thanks Lowes and Maytag, for the worst washer I have ever had the misfortune of owning.

Maytag Oven MGR8670WS1 - Purchased in the Fall of 2011 (along with a fridge... also faulty the freezer stopped working within a year). Ive had the oven stop working twice (in 2012). This week (spring 2014) would be the third time. It seems to be a faulty ignitor already replaced having to be replaced yet again. I have never used such faulty appliances EVER and never AGAIN. This is absolutely ridiculous.

Have had continual problems with Maytag Bravos. They will replace in under a 5 year warranty. If not for the warranty, I would be out over 700 dollars spent on this very bad machine. Based on my experience Maytag washers are of poor quality. I would stay away.

I would not purchase a Maytag in the future. The top oven does not work, and one of the burners is semi functional. Considering I have only have the oven about 5 years. I am not happy with the the product. In the future I would seek other options, Maytag is not on the list of products for consideration.

Top rack fell off with load of dishes. Clips that hold rack to slides broke. Week for repairman, two days for parts, week for repairman. No repairman, call parts be in on 7/28 2014, repairman on 7/31/2014. ONLY HAD DISHER FOR A WEEK, NOW IT IS BROKE. WHAT A RIPOFF.

I own a Maytag MDB9150AWB dishwasher which isnt covered under current recalls. Yesterday, I heard a loud pop sound, and it stopped working (also popped the circuit breaker). After taking the door apart, we found burnt wires at the bottom of the door close to where they bend to go under the dishwasher.I called Maytag to find out if they would do anything, since this seemed like a defect in the materials used. They wont offer anything!

High dollar front load washer, less than 2 years old, just a waste of time & energy to run it, clothes come cleaner, if you leave them out in the rain! DONT buy Maytag, I never will again!! The customer service SUCKS even more than the product, 3 hours of my life spent today e-mailing, calling, live help, NO response? They must have shut down customer support due to the overload of calls from UNHAPPY customers!! NEVER again!!

The control panel acts just like the other reviews on here. The cancel light stays on. If I close the door, the washer automatically starts up again. It is unusable and it costs too much to have it repaired. First and last Maytag product for me.

A refrigerator we have had for just two years has been leaking water from the freezer and damaged our hardwood floor. We thought it was someone dropping ice or leaving the freezer drawer open but no, there is an admitted problem with the mechanism. No coverage from Maytag for the cost of fixing THEIR MISTAKE. The company doesnt seem to care. Got the run around from their management.

I have had this refrigerator for less than 3 years. It recently started leaking water on the floor and all over the bottom of the freezer. Repairman said it is a flaw with the defrost drain design. He thinks Maytag MIGHT have changed it since I purchased mine, but I dont know. Originally they used this small rubber valve;repairman said they get clogged very easily (even though I vacuum around it regularly and dont have any pets). He replaced that part with something sturdy that looks like a p trap. I looked online and there are loads of complaints about this exact issue with the defrost drain clogging. It cost $250 to have it repaired. I called Maytag to ask to be reimbursed and of course they will not do anything since it is out of warranty. Its a shame Maytag wont stand behind their products. Since there are so many of us with this issue, cant something be done?

Bravos XL was costly. Mistake! I owned my first Maytag for 20 plus years. The sticker shock of buying a new Maytag 4 years ago was pushed aside knowing how long my previous model lasted. The salesperson at Lowes closed the deal with his explanation of an improved gear driven system vs the old belt and pulley version. Oh how wrong! I too have the jet plane from hell landing in my home for over 2 years now everytime the spin cycle engages. This is a two person family and it failed at 2 years?!?!?As for water conservation... if I dont include the additional rinse cycle, my clothes dont get clean. Watched the YouTube on how to repair this unit... but what guarantee do I have that it wont go back to the same problem in another year? Cant afford another big investment like this now that I am retired, so I will run this baby until it seizes up. Dont wash clothes if company is coming or if you want to enjoy evening TV programs. Not sure why this unit hasnt been recalled based on all the complaints I have read on this site?? Worst decision I ever made! I bet the Maytag Repairman is spinning in his grave!

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

I waited my entire life to age 47 to purchase a brand new matching Maytag washer and dryer. I was thrilled. That was August of 2012. 3 years and two months later, the $800 dryer (MEDE201YW) loses the entire control panel and Maytag refuses to offer any assistance. I deliberately purchase Maytag with its stellar reputation, an American based company only to be more disappointed in the product and the company than in any other appliance Ive ever purchased.

My microwave started acting up, after about 5 months. It would not cook a complete cycle, without an error saying that the door is open, and needs to be closed. The repairman has been out 5 times already, and the problem is still not corrected. Maytag/Whirlpool has said they will not replace item, then they decided they would possibly replace at a pro-rated amount. So, I have to purchase a microwave twice, to have one that works? Somehow, I feel Im being taken for a ride in this deal.

Bought machine 03/23/15 exactly 2 yrs ago & machine will not work. It looks like the electric panel and which there are a lot of complaints about the panel, and the lid. It seems as its about the extended warranty now. The quality that Maytag advertises is lies. You buy the product and you have no choice but to purchase a warranty on your machine. Simple is better when it last 20 yrs over 2 yrs on a fancy machine. First electric panel machine washer with a horrible experience. It will cost 98 just to look at, that is not including parts and labor. Its 339.15 for a year warranty which equals over 300 per year for 3 years. Overpriced in all ways. Worse choice ever.

Our prior fridge died on a hot long weekend in July 2020. Desperate for a fridge, I ordered any fridge that could be delivered the same day. Received a Maytag which totally died 3 months later! Now I am waiting for a part (which apparently the Manufacturer has 100 in their inventory but havent distributed them to the source that ordered them). This is just the worst service I have ever experienced with an appliance. As so many people have said, I should have waited and ordered a European appliance. They are built beyond perfection and have excellent service.

Our Maytag Bravo washer provided so little water, that our clothes were rarely clean. My husbands jeans gradually developed stains around the knees that never came out, and his white underwear & socks didnt come clean either. After about 3 years, the spin cycle developed a loud sound, like a jet taking off, which was so loud and forceful, it sounded like it was literally going to spin out of the machine. We got rid of the Maytag Bravo after 6-7 years, and Darryls jeans and underwear were clean after two washings. All heavy items, such as blankets, have to be watched over because they always get out of balance several times a wash. We kept the Maytag Bravo, although it wasnt great, and didnt dry clothes completely. These are not machines that you can put clothes in, and just walk away. You have to babysit your laundry.

Maytag dishwasher model MDB7759SAB, 1 year old and control panel will not work at all. Maytag site does not recognize model #, got part numbers off parts and cant find the parts. Looking for control panel, cant find black one and others are back ordered for weeks. After reading other peoples problems, it seems Maytag would correct the issue.