A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

Our washer sounds like an airplane taking off. Called a repair man and the repairs are $690.00. The washer cost $999.00; such a waste of money. I called Maytag and they say there is nothing they can do. I will NEVER buy a Maytag again.

My Maytag MDB7749SAW0 Dishwasher starting acting up after around the first year. The lights on the Control Panel began to flash uncontrollably and it will run all day while I am at work. I called Maytag and they were nice but did not repair it because the warranty just ran out. The person on the phone said that it is a common problem with knob-less dishwashers, the humidity causes problems with the control panel. The cost to repair was over $300 to replace the control panel.

I bought the washer/dryer a few years ago. I did not realize how they do not own up to their reputation. Rather expensive. My clothes are always twisted together when finished washing. Parts of them feel dry. My dryer seems to be ok. Comforters are a pain as the load always gets unbalanced. Lately it wont finish a load. I get LD all the time. Have to unplug the washer and wait for it to cut off before cutting it back on. Then I cannot just rinse or spin. It fills back up with water and I get the same LD again. If I had seen all these reviews before I bought this set I WOULD NOT have bought them in the first place.

Maytag Bravos washer and dryer both need replaced in 3.5 years! Control board had to be replaced on washer in under 2 years and now the replacement went bad in about 15 months. Maytag can’t help! Hundreds of dollars wasted. Dryer is not much better as the control board is now malfunctioning! DO NOT PURCHASE MAYTAG!

If the control panel light on your Ice2O refrigerator starts flashing you will learn about the Non-Customer Service of Maytag. The problem is the High Voltage Control Board. Maytag has been aware of this defective part since 2007. At one time Maytag was fixing these at no cost to the customer via a recall. Then conveniently in 2011 the Japanese tsunami wiped out the only plant in the universe that manufactures the part.Now out of the goodness of Maytag’s corporate heart they offer the customer $300 off of a $2300 replacement (Oh, I am so grateful). It is time for Maytag (Whirlpool) to accept responsibility for a defective product and recall this refrigerator with a replacement. In the meantime if you have this problem, my advice is to go out a buy a non-Maytag/Whirlpool product since Maytag/Whirlpool cannot be trusted to stand behind their products. Please share this post with family and friends to prevent others from experiencing Non-Customer Service.

We bought the Maytag set of dryer and washer just over 5 years ago with ex. war. The dryer now doesnt heat up but the drum does turn. To fix it would cost about $500 maybe more and the parts may only last a few months. I believe that dryer should last longer when only used about once a week. I am now looking at Speed Queen. Cost more but am told they last longer.

350.00 dollars for repair on a 3 1/2 year old washing machine. Machine wont finish spinning and lid lock keeps flashing on and off and sometimes stays off. Never finishes spinning. A lot of complaints on this! This should be recalled! Always was a Maytag customer but no more!

Our refrigerator is 2 years old and still under warranty. The ice maker had to be replaced. Now the water leaks on the floor. The deli drawer cover broke and when you get ice out of the ice dispenser it flies all over and goes on the floor. Our dealer has been fairly helpful.

Last year we replaced a Maytag dishwasher which had a faulty control panel after just a few years of light use (There are just the two of us). It was going to cost almost as much to repair it as to buy a new dishwasher, so we opted for an $800 model (MDB8959AWW6) with a control panel across the top of the door. There had been a recall on that first Maytag for the heating element or something, so we decided to put the credit towards a machine that would last us for years, we hoped!We have been in this house for 18 years and the original cheap builder-installed dishwasher lasted for 12 years. In fact, there was nothing wrong with it when we replaced it with the last one. Whatever happened to the lonely Maytag repair man? We did not buy an extended warranty, but I can see now that probably these things are only meant to last the lifetime of the warranty.We are semi-retired and cannot afford to have the dishwasher repaired, so it will be a decoration in the kitchen from on. Never ever will I recommend Maytag to anyone! One bad experience should have been enough, and we probably would not have bought a Maytag again had it not been for the credit we got for the product recall on the last one!

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

We bought a Maytag Dishwasher - Model #MDB4949SHW a year and a half ago at a Home Depot Location. We had previously had a Whirlpool dishwasher for 13 years of heavy use, with no issues or difficulties. At the time we purchased our dishwasher, there were various different brands on sale, including the one we purchased. The sales rep at Home Depot advised us that although we could get a similar dishwasher for the same price, that this particular model had a 10 year warranty. When I heard that, all I heard was 10 worry free years. MY MISTAKE. I could never have imagined that a company such as Whirlpool would advertise a warranty, that in the end is made up of nothing but false advertising.We ran a cycle during the Christmas holidays, and detected a funny smell of burnt rubber but didnt know what to make of it. I googled the issue and some people had had experiences with perhaps a plastic utensil or some other plastic, being burned by the heating element, so I figured that its what might have happened. I ran another cycle the next day, and the smell was much less prominent so I thought the problem had gone away. The next time we ran a cycle, the water didnt drain. We called in a repair person, and was shocked to learn that both the drain pump and main control board needed replacing.We got in touch with Whirlpool and low and behold, the only items they cover are nonsense items such as the racks, drum, tub...etc....in other words, the parts that are actually responsible for the running of the machine, are not covered, neither is LABOUR. Therefore, in my opinion, their warranty is trash and should not be relied upon under any circumstances. We purchased a new dishwasher just a year and a half ago, and are left with a heap of junk in our kitchen. Our options? Either spend $600.00 to $700.00 on repairs, possibly more, or buy a new dishwasher. When I asked if there was anything they could do to at least mitigate my damages, I was told....Sorry for your inconvenience...but do you have any other questions. I dont have any other questions...but I do have have a comment.... Make your products better....and dont print warranties that are utterly rubbish, false, and only serve to mislead the consumer. Needless to say, we will not be buying any more appliances from this company. Their one and only goal is profit for their shareholders with no regard whatsoever for the consumer. If I could give it ZERO stars, I most certainly would. :)

We purchased Maytag dishwasher model #MDBH989AW53 in January 2010. June of 2012 the control panel died. Luckily, we had the extended warranty. The service company came and replaced the panel. 3 weeks ago, the panel died again! The service company replaced the panel again. Today I got home and the dishwasher is completely dead! I am so furious!!! At this point, I may just have to bite the bullet and buy a brand new machine. This should NEVER happen to an appliance that is so new! What a laugh regarding the Maytag quality! It is the WORST I have ever seen in my life! Stay away from Maytag!!!! Buyer beware!!!!

This Maytag dishwasher has been really dependable, looks really nice, is really quiet, we have absolutely no complaints. I hope it lasts as long as I suspect it will. Would highly recommend this dishwasher.

Works quietly and efficiently and I love it! I dont even know its running and the dishes are sparkling clean when they come out. How could ask for anything more. I would always purchase this brand again. The reliability is another factor, I have had Maytag before.

After using my GE Profile to death we replaced it with a Maytag; mostly for the cost. Although I hate to admit this, remember the old saying you get what you paid for - Well its true at least in the case of this Maytag oven. I am a constant cook and own a bakery, I often bake many of my products at home. Since getting this oven I have had nothing but failures. The cakes are over done, underdone, cookies burnt, not cooked enough; my time frame for recipes is so off! I wrote a cook book and have baked for years so I know for a fact its not some miraculous mishap that all of a sudden I cant bake. Ive had them come calibrate the oven but still no success.Im going to call them again but I felt compelled to let people know this is the worst oven in history and avoid purchasing it at all cost. I plan on having the service team come out one last time but if this doesnt work I plan on replacing it. Its a Maytag Double Wall Oven-Top Convection-Self Cleaning model no: MEW9630DS-SS. BUYERS BEWARE!

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

I bought Washer and Dryer Pair new less than 2 years ago. Within 6 months of purchase, the bearing went - warranty. Then 1 week before one year old, bearing went again. I contacted Maytag. They told me it was my problem and I should have bought extended warranty. Lemon law should apply and I asked about appeal process and was told that there is no such thing. Now, the washer is needing a new pump and it is not even 2 years old!

We bought a heavy duty washer 1 year ago and paid a decent amount of money for it. Had it delivered and installed mid February of 2020. Worked fine until Dec when the lid cracked (which is common said the Maytag repair man), but since it wouldnt lock, we couldnt use the washer. 1 week we were told and it would be in - a month later and over a hundred dollars spent at the laundromat, the part came in. Used the washer for 1 round of laundry - 3 days later all these error codes started and our washer wouldnt work again. 2 weeks this time for the parts and another $100 at the laundromat- a month today and Im told they are on backorder.Called the place we bought it and they said to call Maytag. Call Maytag and they said that they will try to expedite the parts and could offer me a whole $75 for the inconvenience. They will not replace the washer or give me a loaner until the parts are in. 2 months w/o a washer on a 1 person income for a family of 4 and they cant do a single thing to help. If a 10 month old washer needs 3 new parts one of them being a new control panel - within the first year - this is a lemon and should be replaced. I was told they are big on customer service, but obviously Im just a little fish in the ocean and they dont care about me.

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

DB7749SAM1 Maytag Stainless Steel Dishwasher worked great for 14 months then lights went crazy. My last machine was 30 years old before its motor died. I should have fixed it. Maytag needs to step up and fix this. I will make sure everyone knows from here on out, social media is a wonderful thing. I have not even used it that much - still looks brand new and this is unbelievable. I have seen so many bad reviews now on how Maytag has built poorly designed appliances and then to add insult to injury they will not fix their mistakes.

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

To anyone out there who is considering purchasing a Maytag washer. My husband & I purchased a Maytag Bravo top loader washer from Sears Hardware here in Columbus, OH. We had always received great review regarding Maytag products. This washer is expensive & does not work. We started having problems from the day we purchased & had Sears come out three times for repairs. This washer has a built in scale which is extremely sensitive. We are very disappointed in this washer. It takes an entire day to do 3 loads of laundry. The washer goes off balance on every load. It doesnt do a god job cleaning the laundry. I do not suggest the Bravos series to anyone consider purchasing this product. It is a piece of JUNK! We purchased in Aug 2010 and the washer will need to be replaced within the next several months. Keep in mind that more expensive & lots of fancy extras doesnt mean a better quality washer or dryer. Stay away from Maytag or you will have the Old Maytag repair guy @ your door frequently.

I purchased a Maytag gas dryer in November 2011. This is January 2012. I have got to use mine maybe 2 weeks altogether since I had it. It is to be repaired for the 4th time tomorrow. In the meantime, I have to go to the laundry mat to dry clothes, Maytag refuses to do anything about this. They say they are helping me by getting it repaired each time it breaks down. I want a new dryer. The retailer I bought it from will not stand behind this product either. You see these commercials on TV where the Maytag guy is sitting back and waiting on a call. Thats a bunch of ***! I have never purchased a product from anyone that they would not stand behind it especially for the 4th time in two months. I will never buy another Maytag product as long as I live and I will tell everyone that I know not to buy one either.

I bought a Maytag dishwasher just 15 months ago. Worked fine for the first 12 months. Then literally, a few short weeks after the warranty expired, the buttons on the control panel started acting up. The normal button, when pushed, would light up the delay hours. The light cycle would make the rinse only come to life. It was beyond frustrating. My husband would unplug it to reset it and that worked for two weeks but now, nothing. It wont work at all. Im FURIOUS, considering we spent $450 on this thing and now its useless. I had a Kitchen-Aid that I loved but due to cost, decided to get this hunk of junk. I learned my lesson..Maytag, you should be ashamed you make such horrible products.

I hoped the Maytag Maxima would compare to my old Maytag Neptune and it didnt even come close. Very disappointed. Doesnt fill with enough water to even WET the towels and doesnt rinse any of the soap out of the clothes. Been using it since 12/2015. Hate the Maxima. I looked for the brand (Maytag Neptune) which I couldnt find. Settled on the Maytag Maxima which is a complete bust. The Maxima doesnt fill with enough water so Ive had to add water to both the wash and rinse cycles. It has also become very noisy. The repairman has already stated that there is nothing he can do about the lack of water since the amount of water is set in the factory and cannot be changed. The Maytag Maxima is a complete bust for me! Its a front-loader that has me adding water (at least 2 gallons) to every load no matter how small. Wish Id bought a GE top-loader that Ive seen advertised.

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

I have had a Maytag smoothtop stove for over 20 years. The only drawback has been when someone left an empty pan on a hot burner. Some of the pan melted to the top which could not be removed. I have to get special pans to conduct the heat, too. Overall, I love it. It has a self-cleaning oven, too, which is a bonus.

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

Maytag MDBH979SAM1 w/ Steam - I purchased this dishwasher Jan 2014 as a scratch or dent at the Sears Outlet. The dishwasher worked great until 4-5-2015. About 3 months after the warranty ran out I called Sears and asked if there was any extended warranty coverage since I used the Sears card. They said No, but recommended I call MasterCard since my card had the MC emblem. MC says that they do extend the warranty up to 12 months. I just filed a claim and hopefully will get a paid for repair. So, if you used a credit card, you may have a warranty extension like me. Check it out. 2 stars because the dishwater is a great unit except for the control board. What a shame Maytag.

We purchased a French door Maytag refrigerator model MFD2561HEB in November 2007. In August 2008, the unit stopped working suddenly. The high voltage control board was replaced under warranty, but the tech could not determine why the board failed. I called Maytag to demand a new refrigerator. The best they would do was to extend the warranty for 6 months, no charge. The unit quit twice more in September. A tech was summoned (paid service call), nothing found. It started working again. Since then, the thing has quit several times. We unplug, move all food to a second refrigerator, wait a day, plug it in, and move the food back. The useless box quit completely this week, not quite 5 years of service life. The tech said the board must be replaced again, no guarantee. We declined. I called Maytag again to demand a new replacement and escalated the complaint. They are to call back, ha! In the 5 years of poor service (and poor customer service) from Maytag, the 30-year old second refrigerator has been up to the task of preserving our food. This experience has made me vow never to do business with a Whirlpool-affiliated brand again.

No motor is available for the Bravos washer machine which is 5 years old! Now the machine is garbage and I need to buy a new one. I thought Maytag was a great brand so I purchased the Bravos but now I understand from the company that no motor replacements are available!! Wtf? Maytag/Whirlpool dont care for loyal supporters so, I am TELLING EVERYONE not to purchase Maytag/Whirlpool appliances whose name has gone for a dump with this latest situation.

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

We purchased our Maytag Refrigerator Model # MBF2258DEHM on 12/21/2015. Just a couple of issues I would like to bring to your attention before you purchase your Maytag. The single refrigerator door does not close automatically. You have to close the door. The metal handle is metal and has a metal smell and feel to it. The stainless steel door and the handles are not the same finish. Although this might not be a problem for some who like the industrial look I prefer my hands to be free of chemicals while I am preparing food. The ice maker takes up too much room. The ice maker should have been an option, not a standard item. I had a Kitchen Aid for 10 years and loved it. I thought I was going to have my Kitchen Aid for 15 years or more. I would have purchased another Kitchen Aid, but the reviews were not good.

I bought a Maytag laundry set (washer and dryer, models MVWC565FW and MEDC555DW, respectively), and I concur with the fact that this is the WORST laundry set I have ever owned. The clothes came out of the washer extremely dry and did not come out as clean as expected. In addition, clothes came out with strange spots, especially the dark ones. Now, we wash our dark clothes with fear of damage them. The dryer is also pathetic. I put in a normal load on high for 60 minutes, and theyre still very damp. Sometimes I have to repeat the cycle 2 or 3 times. When I compare it with my old laundry set, this is extremely disappointing. And to make things worse, the customer service department doesnt answer you. I sent them a mail, on February 2018, and a month and a half later, I havent heard back from them.

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

I bought a Maytag dishwasher (MDB7749SBM) and 1 yr and 4 months the control panel went out and all Maytag would do is tell me that they will pay for the parts, and I have to pay for the labor. I remember when Maytag had the best Warranty on their appliances. I am very disappointing with paying for labor. They also offer an extended plan of $269.00 for a year. What a joke!!!

3 year old Maytag Washer model MVWX600XW broke. Paid $345.55 for extended warranty. I had to wait 10 days for Appliances Unlimited to fix the washer in Sept. then the washer broke again in November needing 3 more parts including a motor. It took almost 2 weeks for Appliances Unlimited to come to the house, then I have to wait 5 weeks for a new motor to be in stock.

Problem with the front panel are the dishwasher has been replaced 2 times in 3 months. Was told by the tech repair person is not a well made product. He would replace it if he could had a warranty and added a new warranty for 1 year and is up again and of course have to do it. Was told if it happens again they most likely replace with a new unit. Hopefully. Not happy.

What was shown on tv and the way it looked in home depot were much different when I got it home. The refrig. Is big as a bo car on the outside but inside nothing.

I bought a top end Maytag refrigerator with the freezer in the bottom drawer. Spending the extra buck was something that I thought was worth it, being a Maytag. Fifteen yrs go by and it stops completely. It cost me 200 bucks for a service technician to tell me that the compressor or it has a leak. Its not worth repairing. With todays cience and technology, you would think that they can make a refrigerator last for 25 yrs or more, like the old ones. We went to the moon 44 yrs ago. Why cant they make them to last? I think that the corporations figured they can make more money making an inferior product that needs to be replaced every 10-15 yrs. I will never by a Maytag again.

I purchased a Maytag dishwasher on Oct. 12, 2013. The control panel failed in July 2013 and had to be replaced. I was unable to program a wash cycle and the lights would move all around the front. After the first failure, I was told that the control panel would only be covered for 3 months - the original purchase date for the washer, NOT the date of the NEW control panel. I was then talked into an extended service plan. Now, four months later, the control panel has failed again and I am unable to program a normal wash. A repair man is not scheduled to come for another 9 days. As a single homeowner, this product is not used even on a daily basis. I will never purchase another Maytag washer. They do not back their product with appropriate repairs.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

I bought a Maytag range (MET-8775) last year, because my wife loves to bake and wanted the double oven. The oven never did brown properly, despite trying different temperatures and cookware. So, I called the 1-800 number in the manual. I was told they would have a technician come out and check it, and they assured me it was under warranty. The technician arrived, and since it was close to the end of the warranty period, I showed him the receipt for purchase. I got another assurance that this visit was covered by the warranty, before anything was actually done. Well, he checked it out and eventually calibrated the temperature. That helped a little, but still, it doesnt brown very well. About a month later, I got an invoice from the service company that dispatched the tech telling me Maytag will not cover the visit under warranty. After a long call with Maytag (now Whirlpool, I believe), I was told that since the calibration instructions were in the manual, it wasnt covered! Well, why wasnt the thing calibrated to begin with? And your average customer is expected to have an accurate thermometer/gauge to set it and know whether the temp is off or not? Why was I told twice that it would be covered? If either the lady on the 1-800 line or the tech who came had told me this wasnt covered, I would have argued a case right then. As it turned out, I had no choice but to get billed for something I was assured was covered. And as I said, it still doesnt brown right; and we had tried different temperatures before. We are preparing a major kitchen remodel, and its hard to believe that Maytag/Whirlpool would so thoroughly piss off a customer and potential future customer over an $80.00 service call.

I bought the Maytag Bravo XL washer and dryer at Lowe’s on sale spending almost $2000. Loved both of them until the washer stopped with a load of laundry in it. No power to unit. Called for service. Could not provide serial number as locked in washer. Service company able to order parts without the serial number but part put on back order. Washer needs a master board. After 1 week of wet laundry stuck in the washer called store manager at Lowe’s. I contacted Maytag Service and had a rude customer service clerk who finally listened to me after I got angry with her. She contacted the appliance repair company and got the back ordered part sent to the appliance repair company. We are now 10 days out. Still do not have the part; just talked to appliance repair company supervisor. The appliance repair company supervisor said he would schedule installation as soon as he had the part. It will probably be 14 days when I get the washer fixed. I am dreading opening the washer to get the load out that I will have to throw away. When I called for service at Lowe’s the representative said, We have had a lot of issues with this. A 2 month old new washer should not have the control board go out. Shame on Maytag.

We purchased a new Maytag washer and dryer from Home Depot; a couple months later the dryer started to rattle so we contacted Maytag and they sent a service tech out who stated this was normal as the dryer was settling and parts are not as tight as they are when new. This was a garbage response and he was asked to leave. I contact Maytag again, told them of the problem and the tech response and they offered to send another tech out except I would have to pay for the service call since they already sent someone out. I sent them an audio file of the rattle, no reply. Eventually Home Depot ended up replacing the dryer as Maytag refused to help me despite it being in the warranty period.

My Maytag dishwasher MDB780AWW2 was recalled due to electrical problems. They gave me a voucher to purchase another one, plus I had to pay another installation fee. New unit was installed in February 2011, and here I am with a control panel issue. Seems like a similar problem, too. The lights light up, but the dishwasher wont start. Its another $345.00 plus tax repair by a repairman.

My name is Luis ** and I own a Laundromat in Yuma, AZ. I recently purchased 10 Maytag top loaders model MVW18PDAWW in August, so the machines are practically new. They are the new HE top loaders with locking lids. Since I purchased them I have had nothing but trouble. Customers have complained about them on a regular basis; there are days when we have had as many as five complaints.First of all, the locking lids proved to be a much bigger problem than we anticipated. People want to open top loaders to add fabric softeners and when we have opened them so that they can add the fabric softener they are often disappointed with the level of water in the washer. Those people consequently refused to use those particular washers. People have pressed the buttons on the control boards and sent the machines into a loop; different readings have appeared on the screen. Some of them say out of order, sync and several other error codes. Eventually the machines reset themselves or I have had to reset the programming. In the meantime the people pass the word and those machines are not used by those who hear. The controls are too sensitive and are not suited to a commercial coin laundry.Whenever any buttons on the control board are pressed the time of the wash appears on the board. Because of this some people who are busy and are using and loading several washers claim that they have already put their money into the machines; they argue with the attendant or with us. Many times they actually believe that they have placed money in the machine and many times they try to get a free wash from us. Either way they are unhappy and they, and those who hear them argue, will not use those washers again. In most cases we lose them as customers and once customers are lost they never return.I placed them in a location where the previous Maytags had been heavily used, expecting them to replace the old machine. I was wrong. They are used very little and the long and short of it is that we are losing money and since our busy season is coming up, will be losing even more customers and therefore more money. I spent close to $12,000 on the machines, including delivery and installation and right now they are quickly becoming heavy paper weights. I have contacted the salesman who sold them to us, but he has given us the runaround and done nothing about the situation.

I purchased a Maytag dishwasher at Home Depot in Roanoke, TX on 07-14-2011. Model Number: MDB7749AWB2Serial Number: F12604431Unfortunately, Ive just been obliged to open my third service call on this new dishwasher. The first service call was made in August 2012, just outside of the first year warranty period to repair a wire which had come loose in the control panel, making the dishwasher inoperable. The second service call (May 2013) was to replace the front panel housing and touch pad which had broken off at the screw-mounts holding it on to the door. As the handle to open the dishwasher is part of the front panel (which must be pulled out pretty hard to open as it does not have a latching mechanism) screws set into unreinforced, thin, plastic posts holding the panel to the door seems like a serious design flaw.The third service call which I placed last week (August 2013) is to address the fact that the dishwasher has become completely inoperable with no lights on the front panel and is completely unresponsive. To say the least my experience with this product (and by extension the Maytag brand) has been a serious disappointment. I guess the reason I no longer see those TV commercials with the lonely Maytag repairman is because these days hes actually really busy fixing broken down ** Maytags. I will never, ever buy any Maytag or Maytag-family brand appliance ever again.

We bought a Maytag refrigerator bottom freezer at Home Depot in 2012/10/15. A few months ago, a sheet of ice formed on the bottom of the freezer. Since the warranty expired, I decided to look at the problem. Now, I am a mechanical person who usually can fix just about anything mechanical. I used a hair dryer to defrost the freezer and saw that the drainage hole was frozen over. I took the entire freezer apart, cleaned the drainage channel, the drainage hole and reassembled the freezer. No more than 24 hours later, the drainage hole was covered with 1/4-1/3 thick ice, the drainage hose and the tray were dry, and the bottom of the freezer was coated with ice. This one problem that I could not solve. The design is so poor, the draining water freezes over the hole before it drains. I read some of the consumers complaints and I just want to add that do NOT waste your money on repairmen, or parts from Maytag, the refrigerator is NOT repairable. I will write off my loss of $900 and look for a new refrigerator, but Maytag will never see my money again.

Purchased a new Maytag washer top load/Dryer set on April 1, 2016. Having trouble uploading receipt but I paid 1,145.83 for set. It took 2 weeks to get it delivered on April 15. 1st use it shook and wobbled even though the load was balanced but Ive read that is a problem with these machines. 1st load of clothes, washer didnt fill with enough water to wash properly - 3-4 inches of water for a full load of jeans. Top 2/3 of clothes hardly got wet! Changed the setting, same problem. Changed the setting again, same problem. I had to stand at washing machine and keep lifting the lid to get more water in the machine. Clothes didnt rotate in machine so all the clothes on top half didnt get cleaned. The spin cycle is scary! You could hear clunking noises and it had nothing to do with load being balanced. Did a small load and same thing with water level and spin cycle. Called Home Depot to pick up both machines on next business day. The dryer lint trap is so long, it made a mess trying to remove the lint even after only 1 load. NEVER AGAIN MAYTAG! Ive never regretted an appliance purchase like I do now. Maytag and April Fools day are a perfect match. Only its for real and not a joke.

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

Maytag bottom freezer, 4 years old, ice forms on bottom of freezer. Water melts all over floor every few days. Please add my name to class action suit if/when one comes.

I bought this washer from Home Depot and was told I could load large comforters and even sleeping bags in it because there was no center agitator. There NEVER seems to be enough water to wash and rinse clothes completely. The water saver feature cannot be used as I have to use extra rinse cycle EVERY load to rinse soap out of clothes or I get white residue spots. I have MANY MANY shirts that have small tears in them I believe caused by this washer. I have monitored shirts I put in the washer and again today lost another high quality fabric T shirt. I have saved all of the shirts in hopes that one day there will be a definitive report that this washer design stresses clothes and damages them. I am going to purchase a new washer and it will not be a model like this.

So I get the matching set washer and dryer when I moved into my new house. I thought I was getting a nice set. I paid around $1600 for them with the sale they had going on. From day one the washer wouldnt get a full size comforter wet on the bulky cycle or heavy duty cycle. I even tried the extra rinse cycle on both as well. I would have stop it mid wash and rotate the comforter. Clothes wouldnt settle sometimes and would leave the top dry and bottom soaking wet. In the first year the lid latch started going bad. So sometimes you would go back to realize the load hadnt even started. Clothes dont get clean no matter what setting you use. It is the worst purchase Ive ever made. The dryer was ok until its almost second year. It just stopped drying it seemed. I cleaned EVERYTHING! No effect. It takes 3 full cycles at minimum to dry clothes. I cant understand why these machines arent pulled from the market or recalled because they are junk.

Two months after my warranty expired, the motor burned out on my dishwasher. I called Maytag to see what they would offer, but they would only offer a discount on the actual part. I was so angry I was ready to buy a new dishwasher and forget about them...but I dont have that kind of cash to throw away. After going 5 weeks without a dishwasher (first-world problem) I paid for the part and a repairman to come and fix the dishwasher. Now 3 months later, the touch panel wont work. I am so upset that I wasted the money to fix this piece of junk. I will never purchase another Maytag again.

Bought a Maytag Bravos x MVWX700XX1 about 2 years ago and now the agitator barely moves and makes a very loud grinding noise. Never had a major appliance wear out so fast..is a piece of junk. Will never buy another Maytag product ever again. Their old ads about the Maytag guy being bored because he never needed to fix anything should be considered false advertising.

At 14 months old Main computer box failed, caused the machine to shut down on unbalanced load ($400). At 28 months old Main computer box failed, caused the machine to shut down on unbalanced load. In addition when the service guy was underneath the machine to change the module he noticed the stator housing to the motor was falling off. He said he never saw anything like it. After reading about all the problems people have with these machines I have talked friends and relatives out of making the same mistake of buying an old and trusted brand like Maytag. .

I suppose I am the lucky one in that the Maytag Bravos was given to me free. I took out a perfectly good Maytag standard agitator washing machine and replaced it with this several years old unit. What a mistake! I read the other reviews and see that I share the same problems. I always get a the oL fault as soon as it goes to do the final spin. So I have to reset and try again. Also I have seen the same kind of dirt on the clothing as others report. I dont know that I will waste my time contacting anyone about the fault code. I may just put the old one back in and scrap this thing!

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

We purchased a Maytag Bravos Washer and companion dryer in March 2018. I like to wash our king size bedding often and liked that this model had no agitator and could accompany the large loads. I am using the extra rinse constantly since I dont trust the amount of water (not) used. The dryer however, is worthless! No matter the garment or setting, everything comes out in a ball. Tshirts are twisted and wrinkled and half wet. I end up rewashing almost everything then being a guardian for the dryer---checking and rechecking every load. Maytag says sorry, its out of warranty. I absolutely hate these appliances!

I have had this refrigerator for a few years and never have had a problem. It keeps food uniformly cold, and is frost free. While appearance is attractive, it doesnt look like a $3,000 refrigerator. However, black pebbled-surface exterior is easy to clean and scratch-resistant. Plastic and glass interior fittings also have held up very well. I originally thought it would be too small because I was buying it to fit a certain space in the kitchen. But it has turned out to be just the right size because there is no wasted space inside. I bought this at Home Depot on sale for about $400.00 and it has turned out to be an excellent buy. Delivery was on time, efficient, and people were polite and helpful. Refrigerator was ready to be used about 15 minutes after delivery arrived. I have found Maytag appliances to be extremely reliable and made to last. They have never disappointed me. I will continue to buy them. I highly recommend it.

Maytag top loader washing machine - Worst appliance purchase ever made. Does not clean laundry, takes all day to do 5 or 6 loads. Not enough water to properly wash or rinse load, even using the deep water setting (a joke). A load of 2 king size sheets and 4 pillow cases wadded up in a ball and rattled around so hard in the spin cycle, it pulled the plug out of the wall. Maytag sent out technician who conducted diagnostic testing, which did not include any actual laundry. Technician said machine was operating as intended and verified I was using the machine properly. I have tried to return this machine since the first load was done and realized it was a disaster. Maytag refused to help. In fact, their phone agent had the audacity to suggest I wash one sheet at a time to prevent the machine from moving across the floor so far the plug came out of the wall. Maytag surely is not what it used to be. Im sorry I did not know they, like so many other companies, dont care about their reputation or customer service, not to mention producing a quality product. I would say they are actually misleading their customers by calling this product a washing machine.

I bought a Maytag Bravo without an agitator. Regretted from the 1st load. Some of my clothes do not even get wet and I bought the commercial grade. My 20 year washer that was on its last leg washes better than my brand new Maytag. Please do not waste your money, your clothes will not come out clean.

I was sooo excited to get this very very very expensive washer and dryer only to have the worst disappointment and let down...the washer in particular is horrible!!! It doesn’t wash!!! I thought I was crazy until I started reading all of these other reviews and found that many more people have had the same experience as I have... The tub never fills with water and the clothing never gets clean. I would love to start a class action against Maytag and get my money back or get a replacement.

I purchased a Maytag over the range microwave a couple of years ago when I had my kitchen remodeled. I have had it repaired twice already. Each time, it cost over $150. I bought this product with confidence that it was a quality product. To say the least, I am very disappointed and I will never buy this brand again. My previous microwave lasted over 15 years without a single problem. The only reason that I got rid of it was to have matching appliances. It was not a Maytag. I am looking to buy a new microwave and I will be sure to look at the reviews to prevent being suckered again!

Bought a new Bravo washer and gas dryer; Dryer model mgdb980bg. Bought it September 2013. I have had nothing but problems. The dryer would run for 10 minutes then shut off saying check lint trap. Then once it started going again, it close were even damp. It wouldnt sense so it wouldnt start. Finally it got to the point where I couldnt get my dryer working so I phone repair place. The guy came out and set the temperature. Gauges or sensors were off by over 20 degrees as well our entire starter motor was shot. That was over a month ago and we are still waiting for a part that is apparently back ordered. I call today and they said its a faulty dryer and it could take anywhere from a week to two months to get the part. I am requesting a new dryer.

We purchased a 3K Maytag refrigerator/freezer and purchased an extended warranty as well. 5 months later the ice machine stopped working. We called Maytag to get it repaired since its under the 1 yr factory warranty and they sent an appliance service company they contract with to repair it. 6 service calls and two months later its still not repaired. I called Maytag back to say if you cant fix it please replace it. They say it needs to be deemed not repairable to even consider replacement and that they would send out a different repair company. As of yesterday (9/(9/14) another month and a half and 5 trips from the second repair company and it still does not work, so I call Maytag again to complain and they give me the same line ....needs to be deemed unrepairable... How long and how many service calls does it take to fix a ice maker? How much work and how many hours do I need to miss to get what I paid for? I went to their website and it talks about how their mission statement is customer service etc, etc, etc..... Thats just a bunch of lip service and judging by the HUNDREDS of complaints I have read this is their standard method of operation.... I for one will not let this go and will be filing a claim in small claims court to get what I paid for..... BE WARNED if you are looking to purchase a appliance.

We have a Maytag Gemini Double Oven Range Model MGR6775ADW. This is a gas range and it was purchased in 2006. This past Saturday afternoon after cleaning the dishes, the igniters on the range starting ticking on their own. I checked to make sure the knobs were not on and they werent. The ticking finally stopped after about 2 minutes. After the ticking stopped, we planned on going out for a walk. Fortunately we didnt. In about 10 minutes after the igniters quit ticking, the range burst into flames. Flames were in the top oven and shooting out the vent holes and the holes where the knobs are located. Coal black smoke was also pouring out of the vents. I quickly pulled the stove away from the wall to prevent the cabinets from starting on fire and I pulled the plug to shut off electricity from the stove. The flames subsided shortly after pulling the plug. The kitchen and house smelled of burning wire insulation and plastic. After doing some research on the internet, I found out that many other people have had the same problem. I reported this to Maytag Customer Service and they wanted to send a repair technician to fix it. I told them I didnt want it fixed but wanted it out of my house. I told them I didnt trust the range since some people reported they had it fixed and the fire occurred again. I wouldnt be able to sleep or go out anywhere knowing that the kitchen range could erupt into flames at any time. The factory authorized repair technician, from A&E, did come to inspect the damage and to report back to Maytag on his findings. He admitted that he wouldnt even trust the range in his house. After paying $1300 for this range and only getting 6 yrs. of use, I feel that we deserve some restitution from Maytag on this badly designed and dangerous piece of equipment they have been selling. Do not buy the Maytag Gemini range. This is a bad and dangerous product.

I bought a Maytag MDB7809AWW2 dishwasher two years ago. The control panel just started doing free-games. Lights would come on and off during the cleaning cycle. When selecting a cleaning cycle, some functions would be automatically selected without the capability to deselect them. It is our second and last Maytag dishwasher. Stay away from them!

Preheat the oven, put in the food. Oven does not maintain the temperature. Gives me a code of F2-3. Want to know what part needs replaced to solve this problem. If anyone can relate to this problem or help me with information please respond to this or email me.

I purchased a Maytag dryer (MDE2400AZW) 2 years ago, but have only been using it for the last year - and fairly infrequently, as this is a dryer that my guests use. I called Home Depot where I bought the dryer (along with the washer). I thought I had purchased an extra warranty, but turns out I only had it on the washer - what was I thinking. I wish I had read these reviews before I made my purchase. My local repair man charged me $192.00 for a new heater and his time. Theres a whole 90-day warranty on the new heater!! I sure hope this one lasts more than a year otherwise Ill be buying a new dryer and it wont be Maytag.

One month after warranty we had our first issue which cost us $380. Kinda my fault I was told by repair guy... My bra underwire came out during wash and destroyed the part we had to replace. Then a year later during spin cycle it sounds like an airplane taking off for about 10 minutes. Its so loud we cant even hear our TV! So guessing its bearings gone bad now? Which is a very difficult part to replace. And pricey. So guessing a new washer is in our future. We previously owned a Maytag washer and had it for 15 years and it still worked fine, we just wanted to upgrade. Big mistake! I wouldnt wish this washer on my enemies. I think the repair guys sets it to mess up when they do this reset thingy. Lol. Cause within a month of the renewed warranty we purchased was expired is when the 2nd issue began. I think the older washer are better because all this newer technology stuff is crap!! My advice do not buy Maytag Bravos series washer unless youve got lots of cash for repairs!!

Maytag is a product that I would buy any time. Even uses it well last for a long time. If you want to spend money this is a good investment for your kitchen and as for your laundry get the washer and dryer. You do get your moneys worth with Maytag.

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

I purchased Maytag Centennial Commercial washer and dryer eleven years ago. Both are still going strong. It has been a great purchase. Only issue is a couple of stains have appeared on outside of appliances.

I bought my first Maytag French Door fridge about 7 years ago. When it was two it started running water on the floor. I paid a service guy to tell me a tiny little drain in the back clogged up and stopped coil defrost water from draining out. He fixed it. A year later, the fridge stopped cooling but the freezer was cold. I hired another service man who charged me a mint to diagnose that a fan that blows cold air up into the refrigerator failed. Rather than pay him again, I ordered the part. Heres the joke--the part wasnt available. An older part was substituted. Why? The first fan motor was small to make the energy start requirements--but it was too weak to be reliable. The new motor was an earlier model--almost twice as large and powerful. So much for Energy Start. At exactly 5 years and six months, the compressor went out. Im on year two with the new one. I said to myself they cant all be that bad. Now it is leaking on the floor. I have to disassemble the freezer, remove the inner wall, defrost the coils and clean out the drain hole. Wouldnt smart engineers make an easy way to do that from the back? Seems simple.

I purchased a Maytag MDB7749AWM model dishwasher in March of 2012 for approximately $600. Fifteen months later, the control panel has gone out on it. From what I understand, this problem happens so often that its not even worth repairing this dishwasher.

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

Bought mdb7609aww2 dishwasher in 2010. Now I cant use it as it will not start even though the panel lights of my selected wash cycle work. I looked up on internet how to reset it, but I only get a half cycle. Called customer service and for $269, I can get it fixed and get a one-year warranty. Wow, what a deal. Might as well get a new dishwasher. Joining the lawsuit. It is about time corporations take responsibility for defective merchandise, not make money to correct their mistakes by charging customers for overpriced parts and stupid worthless warranties. A pox on them.

3 months after we purchased our Maytag dishwasher in Jan 2014 (Sears) it broke. The service person told us that the ELECTRONIC CONTROL PANEL (START, CANCEL, WASH CYCLE SELECTIONS) was a common breakage issue and fixed it. It broke again around one year from our purchase date. Same issue, but kept working and not working. Finally we contacted Maytags customer service. Although courteous the only thing we were offered for this common Maytag issue was a $249.95 one year warranty for them to come and fix this recurring problem. I explained that we had already spent about $870 (including tax, delivery and installation) for our middle of the line dishwasher one and a half years ago and asked if they would consider either charging us for a smaller service call/repair or just do it because it seems to be a design and manufacturing issue. After one hour and no sympathy I had to pay the $249.95 to get a repair person out and be covered for one year from today. I dont trust the cheap quality and the lack of support for the product. THEY ARE OUT THERE TO SELL MORE INSURANCE AND CUSTOMER SERVICE DOESNT MATTER!

I purchased the Maytag Bravos top load washer and the matching dryer at Home Depot back in 2009 after giving my son my very old Maytag washer and dryer that was running just fine. I liked the top load energy efficiency idea of the new Bravos and the large capacity of both the washer and dryer. Also, the Maytag name sold me, gave me confidence I was purchasing a quality product... WRONG. When it was delivered, there was damage to the dryer door, so a new one was ordered and mailed directly to me. Once it came in, I called to have someone come put it on. First issue, not a really big deal but disappointing.About one month into using the dryer, the top of it became so hot it could literally burn your hand. There was also an error message. I had purchased a one-year warranty, even though technically there is a manufacturers warranty on the product. A part had to be replaced in the panel. This happened twice. We then moved out of state for one year and the washer and dryer stayed in storage unused during that time.Fast forward to 2014 and the washer will not complete any cycle except the spin cycle. I keep getting an error message of OL which means overload. The machine is NOT overloaded. It literally takes me hours to get through one cycle of washing clothes. And they dont even come out clean. I called Maytag repair and they offered me a one-year warranty for $363.75 since the washer is having issues. They explained to me if its the control panel the cost alone for that is $383.00 not including labor. Also, the dryer take forever to dry. I have to run each load through a cycle twice to dry everything. So much for the energy efficiency of these machines. At this point, I am considering just buying another washer, something cheaper without all the fancy bells and whistles. I am terribly disappointed in Maytag.

Bravos XL - This machine purchased in 2014 at Home Depot service plan, needed major repairs just over a year old. Tech working on this machine replaced the whole tub assy after Maytag want to just do the cheap repair and just do a bearing kit. Reading online all the hundreds and hundreds of the same complains Maytag has done nothing in good faith to replace these junk washers!! My washer is now leaking under the washer less than a year after the last repair!! My good friend purchased the same machine and has had the same issues and his has been down for weeks because the poor service person from Maytag service broke some of the new parts! Now the washer is leaking again. WHAT can be done. This not right!!! Public needs to be warned about these flawed machines and Home Depot is still promoting these Junk machines!!!

I would never buy a Maytag dryer again. It has been serviced 3x since purchasing in 2010.

I purchased this machine less than 1 month ago. Have had tech here twice - he cant find anything wrong with machine. As for large capacity it will hold a lot of clothing, but will not clean them. I have had to put less than a 1/4 of tub full of clothing (about 15 small items). Use high water level, extra rinse, then rinse and spin again to get the 2 tablespoons of HE soap off my clothing. Takes over 2.5 hours to wash about 15 items. I have called Maytag and they will not back their product. I purchased at Home Depot and they said they have to do what Maytag says. Sending another tech out in 2 more weeks. Takes more water, more electricity, and more time to wash clothes than ever before.

Further down on this page is my complaint about the dishwasher. This complaint is about the company. This will demonstrate how cheap Maytag is. I filed a copy of my complaint below with the BBB, who in turn forwarded it to Maytag. They sent me a form with rules that they call Dishwasher Recall. Maytag will send me a $250 Prepaid MasterCard, providing that I: 1. Remove the old dishwasher myself. 2. Destroy the machine and/or render it inoperable. 3. Sign and date under PROOF OF DESTRUCTION AFFIRMATION that I have complied. Statement on the form (Your signature is your confirmation that you have complied). 4. Purchase a stainless steel machine (over $700). They list models you should buy. 5. Record on the form; Model Number, Serial Number, Purchase Price, Store where purchased, and Date purchased. 6. Send the signed Rebate Form back along with the sales slip. (Sales slip must show clearly Purchase Date, Purchase Price and Retailer Name). 7. Allow 6 to 8 weeks from the time the Rebate form is mailed. Are they kidding?! If I were to buy a machine at Home Depot, they will deliver, install and remove the old machine. I dont think I would take a Maytag dishwasher for free.

MDB7749SAW - 22 months @ an initial price of $599 and control panel lights become increasingly erratic and finally machine fails to respond to reboot (unplugging) after the third time. Repair man over the phone is familiar with the model and estimates parts at $160 + $115 (gave me a discount) + $125 service call for $400 to make the Maytag run again. Bought June 28, 2012. Installed September 2012. Becomes trash July 2014. Wish I could be more helpful... but if I had purchased the service insurance agreement, it would have run about $90/year... that would have been an extra $180 for a total of $712 including sales tax. So, I had a dishwasher for about 95 cents per day. Nobody rents them. I cant give it less than one star or I would. As a new buyer I was not informed.

I had two Maytag washers in my lifetime: one lasted 15 years and the other 20 years. Neither one had any service calls, just a sudden death. My newest Maytag is 1 year and 2 months old and Ive had two service calls so far due to the sensor unlocking the door. One time there were some socks caught “somewhere” and today the serviceman just reset the machine and it worked. He didnt know why it wouldnt work. It seems to me there needs to be some more detailed trials on these computer-operated machines. If I need another washer, it will most likely not be a Maytag.

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

Maytag Quiet Series 400. Only good thing is the 3 spray arms. The racks are arranged in the worst configuration so you cannot fit many dishes in. The controls are extremely confusing. They do not seem to work in a logical way. The manual is of little help in figuring out how to operate the machine. I dont use the drying feature, so the only options on the panel that work together are Normal and Hi Temp Wash. Ive never had a dishwasher that took 2 hours to wash, but the settings dont allow for a smaller load or shorter time. The rinse agent receptacle is confusing and difficult to understand and use. Way too complicated compared to earlier dishwashers that Ive used. Would not buy this one again.

We have a 2 year old Maytag washer and dryer. 10 year warranty may I add. Well, we get 2 frantic calls that say, “They heard an explosion and the bottom of the house is flooded.” An explosion so violent that it shook our 3 story house and sounded like a bomb went off. Our washer and dryer are on the main floor. When we get there we found the washer top was dented so bad that it dented the bottom of the dryer that sat on top of it - blew the dryer door open! Blew the front of the detergent compartment and blew the side apart! Scared my mother and father in law who lives downstairs and who is bound to a wheelchair! Not to mention the fact that it flooded the basement and ruined the ceiling and Maytag says they will replace the washer! Are you serious? Who wants another washer which may or may not explode! What about the damage to my house! This just happened a couple of hours ago! We are very ticked off and not happy with We will replace the washer! Bad, bad business. This is not where it ends! I want my house repaired and won’t settle for anything less! Shame on you Maytag for putting profit above quality! Consumers beware!

I purchased this set 7 years ago and the washer started stopping mid-cycle and the dryer sensor doesnt work. I called the Maytag service number and after several phone calls (they had my name spelled incorrectly and the wrong address), was able to schedule an authorized servicer. He said the motor and motor controller needed to be replaced and it would cost over $900. When I said I expected my $1,200 washer to last more than 7 years, the service person informed me that the machines were made by Samsung (not Maytag) and just carried the Maytag label. He said the Maytag Neptune washers and dryers were the reason Maytag went into bankruptcy and was bought out by Whirlpool. I am disappointed Whirlpool/Maytag does not stand behind this product and will not buy this brand again.

In 2013, $1850.00 I purchased a Maytag double oven, $700.00 Maytag dishwasher, and a Maytag refrigerator for $2200.00. I have had nothing but problems with all of them.... The oven locked up on me had to call a repairman to fix it. Ive had to replace the control panel on the dishwasher... And the refrigerator!! (WHAT A NIGHTMARE) In 2013 just received the appliance they had to install a heater in the ice maker because there was condensation. 2014, Refrigerator dead.. Repairman had to replace interface and control board.. 2017, Icemaker crashes and had to be replaced... 2020, Now here we are again Ice maker crashed again! (JUNK). My wife told me that she has had nothing but good luck with Maytag appliances... Never again.

I bought a full Maytag kitchen in 2010 because like many others, I trusted the brand. However, before I knew it, the dishwasher broke down. I live in Canada so I get Whirlpool (owns Maytag) 2 year limited warranty. Thank God for that because I have had the repair guy come 7 times. Each time for the same problem (control board) and they have replaced a listed of parts with no success. I have asked them to honor their no lemon policy but am given excuses as to why someone has to come see it first before they can give me a new one. Once the service guy arrived he obviously has no idea about anything and just goes for the repair. Its so frustrating.I am fed up. It is completely unacceptable because now Im losing money staying home waiting for the repair guy. Maytag is the biggest piece of junk I have ever bought. I only hope you see this before buying a Maytag product. Like many others here I use my dishwashers once a week. Now Im faced with a dilemma where I might have to purchase a new dishwasher as soon as my 2 year warranty runs out. My $700 went down the drain.

Maytag Bravos washer MVWB750WQO frame assembly and cabinet rust - I sent letter of internal and external rust issues to Jeff Fettig (Whirlpool CEO) and received no response. Then, I sent letter a second time with an attached signed receipt. Then, I finally received a call from corporate staff member stating they would replace parts but not labor. Labor costs would cost between $350 - $500.00. This is without the initial service call and diagnosis cost between $100 - $125.00. The determined parts list cost would be $700 - 50% for Whirlpool internal cost + shipping be approximately $425.00. This is more than the cost of a new unit or the value of three-year depreciation value of the existing unit. This does not make any financial sense. Whirlpool should provide a new replacement unit at their costs. It has been three months and with no successful outcome. Also, via web research, there are many complaints about Maytag/Whirlpool and I am not the first in regards to rust issue. Therefore, Whirlpool is attempting to limit their financial exposure by only offering parts that they have to agree upon because the labor costs will not support this additional investment in a three-year unit. It makes more financial sense to purchase new or be offered a replacement unit.

Had a problem with the control circuit board on my 6 year old refrigerator. Had it serviced and found that the problem was common, the main circuit board needed to be replaced. The service person advised me it wasnt currently available from his supplier. I call Maytag and they said it was back ordered from their parts source. When asked for an availability date, I was told the date was unknown? I started a search for the circuit board and found it was indeed a problem for many many other consumers who owned this model refrigerator. Lesson learned: Maytag is no longer a good brand to own.

We spent $600 on a Maytag Jet Steam Plus dishwasher and its junk. We bought it in May of 2013 and the top panel is burnt out and the ribbon or control wires is corroded. Maytag wont pay for replacement parts and I wouldnt recommend anyone buy Maytag again. I thought it was supposedly a good brand but its nothing but garbage.

No matter what we we do we still have soap residue left on clothes, even when we do the 2nd rinse cycle (what a waste of water). We use the correct amount of HE detergent and we use the detergent dispenser but it doesnt helps. The machine just doesnt use enough water. We have removed items that still have DRY SPOTS on them when the cycle is done. Areas that have never gotten wet after a 45 minute cycle. Never once had this happen with an agitator machine. Would not buy this machine again. Model: C80441070. Serial #: MVWX655DW1.