This Maytag dishwasher is beautiful inside and outside. I love that the controls are hidden. It cleans dishes very well. It has a large capacity for dishes, a rack for glasses/mugs, a small rack for cooking utensils, and a container for silverware. It is so quiet you hardly know it is working. I would highly recommend it.

I purchased this $857 dishwasher from Lowes in May, 2021. It broke in June, 2021. S&S Repair was sent by Maytag to repair. It took 3 weeks for them to come, then they discovered the motor and pump assembly had gone out. Parts were on backorder. It is now August, 13, 2021 and I still have no dishwasher. Lowes would not replace this dishwasher. Maytag will not authorize a return. This is disgusting.

I bought this new washer and dryer pair at Lowes August 2018. I chose this brand because of the very large wash tub (5.3 cu ft) since I have king size bedding. My previous washer was a front loader, and there were problems with the door seal molding and stinking, and loads had dry spots on them after washing. So within a very short time, I realized I hated this new washer. Very noisy, no agitator, very long cycles. You cannot adjust the time or water levels, and the biggest problem... I CANNOT REACH THE BOTTOM OF THE TUB! I had to steal the grabby toy out of our toy box to pull the wet load out! The laundry comes out all tangled up and horribly wrinkled, even when using the wrinkle-free setting. I line dry a lot of my clothes and now have to iron everything. Never had to do that before. I know Im stuck with this set, but will look forward to the day when it dies and I can buy new ones again.

I purchased a Maytag 2000 series washing machines. It broke and needed to be repaired within six months of purchase. It continued to break and need to be repaired numerous times and its only a little over 1 1/2 years old. It ripped and ruined clothing on numerous occasions. It would not drain and the door would lock with clothing inside thus ruining them. Both of these issues occurred on more than one occasion. Maytags solution for their defective washer was to keep referring me to my warranty. They were no help at all. My warranty finally came through for me and I was issued a full refund through the warranty I purchased at the time I purchased the washer. My new washer (which is not a Maytag) is being delivered Friday. So finally after being without a washer for over two weeks I will be able to wash clothes again. My experience with Maytag was frustrating and aggravating to say the least and I will definitely never purchase Maytag again. They are far from reliable.

Purchased a new Maytag washer from a local Hardware store chain. Waited 3 days for delivery. Old washer was hauled away. Started using new Maytag Centurion the same night it was received. There was a funny odor coming from the washer that was discounted as new equipment smell. Saturday the Maytag Centurion washer was leaking some odd lubricant that had the same odor as the mentioned new equipment smell. Since this lube had been leaking out in close proximity as the liquid detergent my wife used a towel to clean it up. This towel went into the laundry with other clothes.Now Im concerned that whatever this oily stuff is, it’s in all of the clothing that was washed with the towel. Since I live on the West Coast and Maytag only answers the phone during the week Eastern Daylight Time I will call (2 days) after the fact. You might do well by finding out what this lube stuff is before you take it home and how youll have to deal with it once it leaks.

Bought a French door Maytag with freezer on the bottom. Ice build up on the bottom of the freezer and it has ruined my floor. We are replacing the floor in the kitchen. It is only a few years old. They have horrible customer service and will not replace anything.

I bought a Maytag washer and dryer 3 months ago. The Bravo XL is simply a piece of crap. No agitation and clothes come out as dirty as they went in. It also leaves soap stains on all the clothes by since it doesnt agitate enough. Nothing is wrong with the unit, just a horrible engineering piece of crap. Ive been in manufacturing for 30 years and cant even imagine how a company like this can design, test and still sell such a piece of crap. You put a shirt on the top of the load when starting and its still there at the end of all the cycles. Just absolutely horrible. Do NOT purchase any washer without the old time center agitator post. Horrible....

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

I’ve had my dishwasher for over 10 yrs now and I probably need to upgrade but it suits us just fine and I’ve really never had any problem with it at all. My dishes and especially my glasses come out Sparkling.

MFF2558VEM0 - Had the same problem repaired less than years ago.. Now has the same problem. Looking for a new fridge. Hope better luck this time.

I take pride in my cooking and love my kitchen. As you know this is where everyone gathers when you are entertaining. The Aqualift system does not work. I have run the process 3 to 4 times consecutively in row and the inside oven the oven is never clean. I wipe out the sides over and over. So disappointed. The only saving feature is that you can not see into the horrible look of the inside the oven when it is closed. Was this feature really tested before it went to market????

I bought a Maytag range (MET-8775) last year, because my wife loves to bake and wanted the double oven. The oven never did brown properly, despite trying different temperatures and cookware. So, I called the 1-800 number in the manual. I was told they would have a technician come out and check it, and they assured me it was under warranty. The technician arrived, and since it was close to the end of the warranty period, I showed him the receipt for purchase. I got another assurance that this visit was covered by the warranty, before anything was actually done. Well, he checked it out and eventually calibrated the temperature. That helped a little, but still, it doesnt brown very well. About a month later, I got an invoice from the service company that dispatched the tech telling me Maytag will not cover the visit under warranty. After a long call with Maytag (now Whirlpool, I believe), I was told that since the calibration instructions were in the manual, it wasnt covered! Well, why wasnt the thing calibrated to begin with? And your average customer is expected to have an accurate thermometer/gauge to set it and know whether the temp is off or not? Why was I told twice that it would be covered? If either the lady on the 1-800 line or the tech who came had told me this wasnt covered, I would have argued a case right then. As it turned out, I had no choice but to get billed for something I was assured was covered. And as I said, it still doesnt brown right; and we had tried different temperatures before. We are preparing a major kitchen remodel, and its hard to believe that Maytag/Whirlpool would so thoroughly piss off a customer and potential future customer over an $80.00 service call.

We purchased the Bravos XL Washer (top loader) and dryer about a year ago and have had issues with it since it was installed. Please note, we live between two homes so the machines are not heavily used at all. Our $250 machine we have in our Florida home works a million times better and is several years old. We purchased at the ABC appliance store and they have sent out a technician 4 times in the first few months. Bottom line, these are just pieces of crap machines. They cannot be returned! It is really a shame for the money spent and your clothes does not get clean on any cycle. The technician told us we should use the Deep water wash for all cycles which still does not work. I bought this machine for the XL capacity but also for the delicate cycle and stains do not come out, undergarments are still dirty, white power residue from OXI is left on the clothes etc... DO NOT BUY. This would get zero stars if I could. So disappointing and frustrating. If class action suit does happen, I would want to be part if it.

We purchased our washer and dryer set in December of 2010 and had it for about 2 years with the extended warranty...needless to say around 1 1/2 - 2 years the metal around our bleach dispenser started rusting. Maytag considers this cosmetic! I am shocked to think that its cosmetic...on the outside of the washer yes, but on the inside no! It is faulty on Maytags part. I have spoken with Maytag and they tell me if it doesnt happen within the first 30 days there is nothing they can do. So I will tell anyone and everyone what was said to me via Maytags own repairman, Buy cheaper washers as NO ONE offers an extended warranty on the inside of the washer rusting. Whirlpool is the owner of Maytag now so beware of Whirlpool as well. Check out the warranties and make sure you will be covered longer than 30 days for rusting on any washer you intend on purchasing. We learned the hard way and well....we will be buying a cheap washer like the repairman suggested when this one goes out.

Bought this as W/D set brand new from Home Depot. Had been noticing incredible wear and tear on clothes, as things get so tangled up and need to be practically ripped apart before going into dryer. Cycle times are crazy long, up to over an hour in some cases. Doesn’t have a “Speed Wash” cycle. But WORST of all, after less than 3 years, it just stopped draining properly. Tried all the Codes test, etc. Finally called a repairman just to be told repair costs would probably cost more than the machine is worth. $125 to be told we ought to just buy a new washer. Not happy.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

Just read Ann of Colorados (posting April of 2014) message about her Maytag Bravo washing machine and its like I wrote it myself! Our Bravo started with making a loud noise during the spin cycle which turned into oil or a dark liquid spraying out from under the machine, along with saying UL, so I would adjust the load and get it going again only for it to start the spin and rinse cycle all over too! We have 5 people in our family and cannot afford to not have a working machine. We purchased this machine only a few years back to replace another product that was also a piece of junk. I guess as a last resort I will try a Spin Queen which is American made and hopefully will work! Very disappointed in Maytag. Whatever happened to Machines lasting like they did for our Grandparents?

Control panel on front of dishwasher quit. Unit is 15 months old. Bought extended warranty through Home Depot. Took two hours on the phone to finally get to the correct department, they set an appt. for the following Wednesday between 10-2. Had to take a vacation day. Get a call from the appliance repair co. the night before stating they cant live by Depots schedule, they wont be out til the following Monday between 9-1. Schedule a vacation day. They come out then have to order parts, they wont be in for 7-10 business days. After 12 business days, I call back and they set appt. between 10-2. Schedule vacation day. They come out and the control panel the warranty company sent is the wrong one. Now I have to start the whole process over again. DONT BUY MAYTAG AND DONT BUY WARRANTY OR APPLIANCE THROUGH HOME DEPOT.

Wish I had read the reviews! I have had Maytag before and they were awesome. New purchase is horrible! Doesnt clean the clothes, leaves a residue on clothing and dryer does not dry properly. Called Maytag and they said use Affresh. Spent $10 on a pack of 5, and it did no good. My dark clothing is getting ruined! The washer is also incredibly LOUD! Very disappointed in this company and would never recommend them to anyone! I had purchased at Lowes, but had a delayed delivery, so I cant take them back, or I would.

I purchased this dishwasher about eight years ago, and I love the performance and the stainless steel interior. I never have a problem getting my dishes clean. This product definitely lives up to its reputation. Going forward, I would definitely buy the same brand if it became necessary.

We purchased a new Maytag washer and dryer from Home Depot; a couple months later the dryer started to rattle so we contacted Maytag and they sent a service tech out who stated this was normal as the dryer was settling and parts are not as tight as they are when new. This was a garbage response and he was asked to leave. I contact Maytag again, told them of the problem and the tech response and they offered to send another tech out except I would have to pay for the service call since they already sent someone out. I sent them an audio file of the rattle, no reply. Eventually Home Depot ended up replacing the dryer as Maytag refused to help me despite it being in the warranty period.

MF12665XEM7 Maytag Fridge water runs on the floor: After reading the review and watching the video to fix, I called Maytag. They refused to help. We bought our fridge at Nebraska Furniture Mart. We have spent a lot of money with them too. My husband called to see if they would split the cost of the service call. They refused. My floor is ruined from the water leakage onto it when we are not home. We try to catch the ice buildup and remove it before it is an issue. Why is there no class action suit? There is definitely a problem with this fridge and Im seeing it online everywhere I look.

We had a three-year warranty which expired. We used a repair once for a rusting Clorox basin. Now, the tub swings wildly on every wash and will not complete because we get the UL warning. Weve tried making sure the washer was balanced but confirming that nothing helped. Most expensive washing machine ever and shortest life apparently.

Centennial HE top loading washer - When I put the HE Tide powder in the washer, it does not always rinse well. I have to rewash often. I use very little soap.

As with most other owners I am dissatisfied with the cleaning action of the machine. I suspect, that in an attempt to garner green bonus points, the engineers have tweaked the cleaning water amount to the absolute minimum that may do the job and lengthened the wash cycle to the point that laundry for two average adults is an all day affair. Only get a decent washing job if you make very small loads. If you put a set of king cotton sheet in the machine, you will find that the machine manipulates them into the shape of your compact spare tire, and when you take them out... you will find many sections where the water did not reach... bone dry! Reload, rewash, ground hog day with each load. Cant wait for it to throw a bearing so I can get something else.

Absolutely the worst washer I have ever had. I have read some of the other reviews, wish I was smarter and checked this out before spending my hard earned money to buy this washer. My washer also is rusting at the top where the bleach goes. I never close the lid when not in use my basement is dry AND I never use bleach??? My clothes come out they are a tangled up mess. When I go to hang them they are partly dry. It isnt as though I stuff the washer NEVER put more than 8 shirts in at a time yet they all come out with dry streaks like that part of the clothing never even got wet. We all know what happens when you leave a tissue in your pocket and it goes through the washer... Well not with this washer the tissue sometimes came out as dry as it went in. HORRIBLE product. I want the old agitator/I SET THE WATER LEVEL type back. It takes forever to get laundry done. They should take these OFF the market and give us poor consumers some cash back.

I agree with everyone one else and their experience with these washers. I took advantage of a credit for those replacing old washers with new HE washers. IF I COULD ONLY GET MY OLD WASHER BACK!!! Its only 2 years old and it sounds like - what others have said, like a B52 taking off (during the spin cycle). I dont have rust spots inside of the machine or out so Im not sure what the issue is but I really dont want to invest in a couple hundred of dollars to this thing. It stinks, doesnt clean well and now this! VERY disappointed...VERY. As a single mom, the thought of finding money to replace something that is new just disgusts me! Nothing like the old washers that last for 18+ years. Nice Maytag I will never purchase another product of yours and will spread the word!

Bravo XL washer and dryer - I had the washer approx 2 months before it leaked water all over the laundry room. The company replaced the washer after two weeks. Now the dryer has gone out after two years. If it cost me the amount stated by other consumers I wont be fixing it.

Spent $2,000 on Maytag washer and dryer in September of 2020 thinking we were buying quality and a company that backs their products. Forward to January 2021 and were not able to schedule service through their website. Not able to get anyone to answer their phones. Called what used to be our local Maytag service and they told me Whirlpool took over Maytag warranty service and cancelled all the contracts for local repair shops. So, not only do we have a 4 month old washer I wish we had never bought, we cant even the Maytag to service it under their warranty! Never again...

Three-year-old top load Bravos. Started doing the LD/SD tango about one year ago. Intermittent fault, but becoming more prevalent. Can spend an entire day attempting to finish one load; sometimes must be unplugged overnight to clear faults. Washer receives heavy use from extended family of five adults and two children but has never been overloaded. Machine is horribly flimsy and constructed of the cheapest possible materials. I wish I had removed the back prior to purchase.Just because it is possible to attach a processor to a piece of equipment doesnt mean its necessarily a great idea. Any geek can tell you that the three things most despised by a digital device are heat, humidity, and vibration. A washing machine by definition is an epicenter, a breeding ground, for those specific environmental factors. Well done, Maytag. You have demolished what was, perhaps, the most respected name in the business. Good luck getting that particular rep back. Purchasing a Speed Queen. The living embodiment of old-school. Electro-mechanical timer. Stainless. Porcelain-enamel. American-made. Not one complained on this site. Might just shoot an Office Space vid centered on the demise of the Bravos. This time, its personal.

In July 2006, we purchased a Neptune Washer. The only problem we had with it is it does NOT spin the water out of the clothes after the wash cycle. This has been going on for about 4 years. In February 2012, we had a service person to examine the washer. According to the service person, there is nothing wrong with the washer. He said to put in clothing of the same type: All towels, all jeans, all pillowcases, etc. This is not the real world. This cost me a service call with no solution. On June 10, I called Maytag on my issues. They have no recalls or issues with this washer. They recommended another service call which I refused. I even offered the washer free of charge to the person I was talking to, but did not get a response. Never again will I purchase a product from this company.

Purchased Maytag Model MVWB865GW0 Ser# **, had it ONE year, circuit board and switch have gone bad, will not turn to change the type of wash cycle and the lid will not lock, which makes the washing machine not start to wash. Contacted Maytag to request a service call, per the service team the circuit board will cost $300, plus a switch $75 and Labor $100 plus tax. We will be better off buying a new washing machine! We should not have this high cost within ONE year of purchasing! Will not purchase a Maytag again!

MDB7749SBW - Purchased a new dishwasher from Home Depot & had them install it. It worked for 6 1/2 months & the control panel blinked & went dead. I did some research & found there were a lot of problems with the control panels & even a class action lawsuit. I went to Home Depot & they said contact Maytag & brushed me off. I set up a repair per warranty & all was fine for 10 months & same problem has happened again. I told them at Home Depot to replace the unit since nearly every repair job on the control panels prematurely fail again every time. I am going back to the Home Depot again. I do have older Maytag appliances that perform as required & I do know Lowes would have replaced the defective dishwasher.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

I originally wrote a complaint on 5/20/09. This is a follow-up. From the time I wrote the complaint until February 2012, I had been dealing with this Maytag Atlantis washing machine (and dryer, which was equally as bad) and I am pleased to report the thing finally died for good! I got another (almost) 3 years out of it! Thats pretty impressive when you consider that I had to manually adjust each load to re-spin. To recap, I purchased it in the summer of 2002 and managed to hold on to it for almost 10 years. I wouldnt normally recommend doing what I did but I was determined to run it into the ground before I replaced it. I replaced it with a GE washer and dryer and couldnt be happier. Maytag will get no further business from me.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

Purchased a Maytag refrigerator in July 2011. The compressor failed May of 2013. After many phone calls to Maytag they replaced the parts (compressor) - my cost for labor (aprox $300.00). 30 days later, the service company had to repair a leak and recharge the system. March of 2015 the compressor failed again. Have spoken to Maytag (case # **) - they will provide no help what so ever. I was told I should have purchased an extended warranty.

Maytag Model MDB7749SBW: Lights on control started flashing even when not it use, cycle lights varied, dishwasher would start on its own. Stopped at dealer and he said he never heard of problem. Checked online and found problem identified all over the internet. Called Maytag and they knew of problem and said they would send serviceman out to check. First trip free and parts would be free but I have to pay labor for second trip to repair. Dishwasher is just under 4 years old. Serial F31703877. Problem is corrosion on small flexible circuit at top of door. Same problem as others. Maytag states never been a recall!!! THIS CERTAINLY HAS THE POTENTIAL TO CAUSE A FIRE. Will never purchase another Maytag or Whirlpool appliance again. Poor quality and lies on the part of company and dealers as well.

The washing machine is rusting and Maytag refuses to take care of their inferior product and obvious inferior materials used, and also inferior workmanship.

I purchased my 2nd Maytag Neptune washer in 2005 to replace an early Neptune that was complete junk. This one worked OK until this year when it began to make awful noises. After research, I decided it was the bearings that failed. I took the unit apart to get to the bearings and found out the entire outer tub must be replaced not just the bearings, at a cost of $515. What lousy engineering, the bearings dont come out of the housing. No wonder Maytag repairmen are so bored. There is nothing to fix, you just buy a new washer. I wont buy Maytag this time.

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

Maytag Washer Model#MVWC465HW2, just purchased it 1/30/2019, leaves white stains on dark colored clothes. I use liquid soap. I don’t use softener nor bleach. I use OxiClean on my whites and sheet softener in the dryer. Someone please out there help, I can’t return it, it’s past 30 days. I have extended warranty but they can’t help. It’s not broken. I hear a lot of bad reviews/complaints, but no answer if it’s been solved or how to solve it. Please someone help???

Our Maytag Elite Series dryer is not under warranty but we have had nothing but issues with this dryer since we have had it. However, now I have holes in the heat intake at the back of the drum. This is so very dangerous and could cause a fire. I am certain this is a manufacturing flaw. How on earth does the inside of a dryer have parts that will not hold up to heat? At any rate, I want it fixed. The only way to fix it is to replace the drum. This has to be a flaw in design or manufacturing and this particular model should be recalled.

I bought the power wash Bravos XL... Bad. It does not rinse the clothes, leaves residue on dark clothes.. probably all clothes - cant tell on lighter colors. I dont recommend!!! Waste of money.

I purchased a Maytag dishwasher with a control panel in September of 2013. In August of 2014, the control panel died and did not allow me to run the washer. In March of 2015, the piece which was replaced died. When contacting Maytag, even when they did the repair the first time, said they were unable to cover the cost because it was now out of warranty. Ive seen several class action lawsuits around the product with Maytag. Do not buy a Maytag. It used to be a quality brand, but is now terrible.

We bought the Maytag set of dryer and washer just over 5 years ago with ex. war. The dryer now doesnt heat up but the drum does turn. To fix it would cost about $500 maybe more and the parts may only last a few months. I believe that dryer should last longer when only used about once a week. I am now looking at Speed Queen. Cost more but am told they last longer.

I have been trying to solve the issue with my washer, that my parents bought me for my new home. Home Depot, where they were bought, came out twice, and all they say is there is nothing wrong with the washer. There are plenty of things wrong with the washer. It doesnt clean the clothes. I have to use the heavy wash cycle, to try and get the clothes clean. Maytag wont even deal with the situation. The fight has been going on for over 2 years (washer serial # is CY4744432 manufacturers number is MVWC6ESWWI).Not sure if I should just give up. Im really tired of fighting with Maytag and Home Depot. I hope you can help.

We have had a Maytag Bravos washer for a while, which has a see-through top load lid and a very small or low agitator. I have to say that I really miss the old fashioned agitator which makes all the clothes being dragged underwater and scrubbed well. We have watched the loads being washed in this washer many times and the clothes are not being swished around very effectively. You feel like you need to help it getting the clothes washed as it seem like it just sit in the same place throughout the cycle. The clothes ends up in big knots around the edges, and you can see the same towel sitting on the top during the 2-minute rinse cycle, never getting completely under water. During the wash cycle, the lid gets locked, so you are not able to open it up to untangle or move towels around if it has gotten unevenly distributed. The wash cycle is very quick, so all in all, Im not sure how clean the laundry really is when its done. We will never buy this kind of washer again.

I had noticed the lights, such as for sanitizing cycle, hot water cycle, etc, would go out intermittently, but since the washer still ran, I was down with that. Loaded it up last Sunday, pressed the button to start and El Zippo. Nothing works. So here we go again with another crap product from Maytag. Yes, I have had this dishwasher, which was a pricier model but closeout priced, at Lowes in 2008, BUT I live alone, so how many dishes do I wash. At the same time this is the third time had a repairman out (with no help from Maytag other than trying to sell me an extended warranty for nearly $400) and these machines ought to last a lot longer than this. The part online is bad enough, $150, cant wait for the repairman to call me back tomorrow and see how much they are going to hose me for.

We purchased a Maytag dishwasher model number mdb7749sbm in April 2013. March of 2015 the controls stopped working completely. We looked online and instantly found it was a problem among many others, and said it was a result of corroded ribbon cable. We opened the panel and, sure enough, inside the ribbon cable the electrical wires were completely rusted through! We called Maytag, and, of course, despite the numerous complaints of the same problem, they would only fix it if we paid $250, or send us a replacement part for $350 to fix ourselves. Not going to spend that much on a dishwasher that already cost $600 and only lasted 22 months! We are attaching a picture that shows after we tried cleaning the rust (when Maytag refused to fix it) how much of the electrical wires disintegrated! We tried soldering a small wire to connect it again, but the ribbon was so thin it just melted right through.

This has nothing to do with the vendor. This is clearly shoddy workmanship on the part of Maytag. I bought this refrigerator in 2005 and already the compressor is gone. So therefore, I have to replace the whole unit.What kind of ** is this? You mean to tell me that you people cant find someone to build a compressor that holds up more than a few years? Why dont you try American made and built.I am disillusioned by the whole industry. Im sure the people at the top could care less.

Washer would stop right after it started. I googled the problem and found out it was a bad lock. These Bravo XL units were purchased in 2015. Called an appliance repair and they charged me $250 to replace the lock (service call was $98.00 and labor was $90). The repairman left and I started the washer. There was a loud sound coming from it. I called the repairman back and he said it was the gear case and basket. He said the basket was covered under the warranty but the gear case wasnt. Would be about $750 to fix....no way was I paying the cost of a new washer to fix this less than 4 yr old one. I called Maytag. They couldnt help me. I should have purchased an extended warranty they said. The cost to purchase the extended warranty is now $394.00 per year....please do not purchase a Maytag/Whirlpool appliance unless you like buying extended warranties.

MFI2670XEMS - I bought a Maytag Fridge MFI2670XEMS in 2012. I dont remember how long it took to start leaking but it wasnt long. Same thing as what most people are complaining about - I also have hardwood floors that are ruined. I just had a kitchen remodel and now I wish the floors werent new. Warped badly under the fridge. It is a constant pain. I have to break up the ice with a blunt object to get it out. I was so excited to get a new fridge. Of course it was on sale, now I know why. I wish I had just kept the old one, at least my floors would look great. Lame.

I purchased my machine on June 2, 2021 and it was delivered and installed on June 4. I have successfully done two loads of laundry. On June 9, I attempted washing two small bath mats and 2 dish towels. When I returned to the laundry room to place the load in my dryer, I found the the items in soapy water. I tried many times to reset the load with no success. On June 10th I called Maytag’s customer service and spoke with an associate who walked me through a couple of common quick fixes. These also were unsuccessful. She referred me to warranty service. I will not be able to have my machine repaired until June 23rd! Obviously, if their repair department is so overwhelmed, the products they sell are a piece of junk. I am furious with both the product and the service I have received.

Purchased the Maytag Bravos XL washer and dryer in January, 2014. Today, 5/16/15 (less than 1 1/2 years later) the repairman tells me that the cause of the loud noise in the spin cycle is bad bearings. Only a 1-year warranty on the machine. I have never purchased extended warranties on appliances so this will cost me $400! Or a new washer since this is more than half the cost of the new washer. This is bad business, Maytag. Ive been a loyal Maytag customer for years but I think Im heading to Speed Queen with their 5-year warranty unless youre going to give me a helluva deal to keep me. Grrrrrrr.

Bought a Maytag Dishwasher (Model No. MDB7749SBM2) in Sept. 2013 and I am in need of repair for the control panel. The dishwasher is in a vacation house and isnt used on a daily basis. I always thought Maytag was a reliable product but Ive been reading the reviews and the control panel is a problem on relatively new units. How do they get away with this. The unit was around $600 and now Im stuck with a big repair bill... and it appears, from what Ive read on this site that it is a common problem. Maytag has replaced the control panel part and, as far as I am concerned, they should have provided them to all the consumers who were stuck with the defective ones they sold us in the last few years. Now we all know why we dont see the Maytag repairman sitting around with nothing to do on TV. Hes working his ass off trying to fix the dishwashers.

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

French Door Maytag MFI2569VEW10 faulty in many ways. We bought our refrigerator 7 years ago. After 2 years the freezer door handle fell off; after 4 years the right front door gasket began to tear (normal usage); after 7 years, it no longer dispenses ice or water. We now have mildew/mold growing around the edges of the door because there is no longer a good seal. Constant cleaning. Additionally, we are spending more $ to keep the refrigerator at the proper temperature because the seal is broken. To repair these items is almost $700 including shipping and tax. This does not include the cost of labor. So after 7 short years, we have a hunk of junk that does not work properly. I am shocked that Maytag sells such an inferior product and we are left holding the bag. Do not buy Maytag. Additionally, our Maytag microwave broke after 5 years. DO NOT BUY!!! Buyer beware!

We purchased all new appliances 3 years ago including a Maytag dishwasher. Same problem as a lot of others. We had the control board fail three times in just four months. Now today the repairman came and while he was here contacted other Sears technicians and Whirlpool technicians. They came up with the idea to replace the detergent dispenser which they said is causing the main control board to fail. However, while the tech was on the line with Sears and Whirlpool they done troubleshooting on the detergent dispenser and found that it was all within specifications. In fact, that was not a problem because it worked as it should. But in their wisdom they decided to replace the detergent dispenser. We now have to wait another ten days for the part to arrive and reschedule another appointment to have the detergent dispenser that works replaced. The serviceman that was at our house said that they are making him replace a part that is working and that this does not need to be done but he has to take instructions from Sears technicians. Our service person said that he doesnt anticipate that replacing the detergent dispenser will make the dishwasher work but he said if it does it will only last a few weeks as before and then fail once again. We have the dishwasher on extended warranty and there are about 22 months. I suspect that this one will be going to court to get resolved. Never Maytag again or Whirlpool.

PURCHASED WASHER FROM LOWES. IT STOPPED WORKING IN 2 WEEKS. CALLED MAYTAG FOR SERVICE. First repair service wanted to charge me. Next repair company Rawlings made 2 visits, looked at washer 1st visit said they had to order top latch. 2nd visit need circuit board. 3 weeks passed no latch, no circuit board, nor repair service. DO NOT BUY A MAYTAG WASHER.

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

7 years is all I got from these appliances. The Maytag Washer started making a horrible noise when washing then smoke and shut off. Dryer would not shut off. We have taken excellent care with these appliances servicing them as we had an extended warranty on both. They cost us over $600 for the washer and $589 for the dryer, a big rip off! I purchased them in hopes I would at least get 15-20 years of service as Maytag is to be one of the best. Do not purchase any products from this company, they also have sister companies. Make sure when you need an appliance, you ask who makes them.

Lid lock issue. 2 years old. I will never buy a Maytag, or any other Whirlpool brand for that matter. I am VERY disappointed. A service call will cost at least $200 dollars so why not just buy a new washer for that price. Also, I read that consumers should stay away from automatic water level washers. They never work right.

I bought the Maytag MVWX700XL1 (Bravos X) model in 2012 from Home Depot. I paid over $800 for this washer. I knew I was in trouble when I found dry spots on clothes after the washing completed. I started using the Bulky cycle. So much for saving water. It has not been overused, its only two of us. Today the spin cycle sounds like a train. The washing cycle has stopped working completely. Im very dissatisfied with this washer.

I am very frustrated and disappointed with all of the appliances I purchased from Maytag, 3 1/2 years ago. The stove has never cooked evenly, and they replaced both heating elements, and it still does not bake properly. I just called customer service, because my pies for the holidays burned once again. They told me there was nothing they could do. I cannot believe a customer that spent this much money with Maytag (purchased a washer, dryer, microwave and oven), gets no help from the company. The transmission has been replaced in the washer, and is still noisy. The dryer is also very noisy. The stove does not bake properly, and the microwave quit within a few months of purchasing. The quality of Maytag is very poor, and the customer service is obviously poor too, when they said there is nothing they can do for me. I guess they do not care about customer loyalty.

Second time I have purchased a Maytag washer. Both units failed within six months of extended warranty running out. Maytag repairman is sitting on his **, not because they have a quality product but because consumers are seeing that it is a subpar product. Don’t waste your money on them or any of their off brands.

Worst brand ever. They both broke at the same time. Spend too much money. Never buying these brand again. Maytag sucks. Dont buy Maytag washers or dryers.

My model has 2 ovens which I love. A smaller one & a regular sized one. It also has a cooktop. The cooktop always has “marks” on it from the pots & pans. No matter how careful we are, the pots leave marks. We even bought new pots & they leave marks. Something that we do like is that 2 of the burners have “select a size” so these burners can be used for small or larger pots.

My husband and I were Maytag fans, and we purchased the fourth set of Maytag w/d in May 2019, along with an extended warranty. Four sets may seem like a lot, but my husband and I have been married for almost 30 years now. Long story short, the washer went haywire, and kept flashing LF. After searching Google for answers, my husband flipped the main breaker, then unplugged the washer overnight. It seemed like that fixed the problem, but it didnt. I called Lowes for help and got hung up on numerous times. The hang-ups were not due to my attitude or choice of words. I kept getting transferred from person to person and put on hold, then the phone would go dead. Eventually, someone actually spoke to me and gave me an 800 Maytag number to call, which resulted in more hang-ups.As before, eventually I got to speak to a real human being who took my info and said that a service tech would contact me. Well, over two weeks later, no one has contacted me. However, due to my post/review on the Maytag website, a Lowes representative did call me and offered me a full refund on the washer, but not a word was mentioned about the dryer that seems to be possessed because it turns on and off at will. My husband and I have a limited income, and we purchased the top-of-the-line Maytag w/d thinking that it would last at least ten or more years.For the money that we spent, the w/d should have at least lasted for the warranty period. As noted before, Maytag was once the Toyota of w/d. You could not purchase a better product. Now, the exact opposite is true. Buyer beware, the most expensive with all of the bells and whistles is not always the best. My husband and I have gone retro with the purchase of a new Speed Queen w/d, which will be delivered this week. Hopefully, it will live up to the reviews that I have read.

Did not know of the lawsuit or recall. Now I have to buy a new washer after fixing it out of pocket and mad that cant get part of the settlement. Not ever going to buy Maytag again!!

The $1,100 Maytag Bravo XL does not have a dedicated spin cycle. Its rinse and spin. When out of balance, you rearrange and it rinses AGAIN - 15 minutes - before you know whether its balanced. By rinsing again, it can redistribute to be out of balance. Repairmen (w/ extra warranty) said you cant wash bath mats, bedspreads or pillows though it had giant capacity! They would charge me if I called again about it (3 strikes). So bought a used Kenmore with no computer panel... Its great! My dealer had the Maytag hauled to a dump, he would not sell it to anybody as he had integrity.

Deceptive company and won’t stand behind their product! Purchased brand new washer. Identified and reported noise that I can hear upstairs in my house while washing to technician. Changed a part, not related to the noise. Called back out. He admitted he could hear the noise. Whirlpool engineering department says normal. Sorry, I should never hear a clicking noise upstairs with two closed doors and 150 feet between me and the washer. Will be going back to Samsung next time.

Maytag dishwasher #MDB 9750AWQ - I am now on the fourth control panel and in less than one year, the present one is starting to fail. The third one failed in less than a year also! I have read the reports of others and apparently, this is not just my dishwasher. Maytag owes its customers a recall of this inferior machine.

We had a wonderful Bisque Maytag double oven in 2002. We bought new stainless appliances this year, and have been very disappointed with the range. Why do you have to hold the temp and timer settings one increment at a time to set it, and why do you have to push Start after that? Frequently we set the temp or timer and walk away, only to find that the oven or timer did not begin because we forgot the new step. When the timer goes off, you have to push it twice to get it to reset. The burners themselves have too many confusing pictures for the settings. What happened to low heat, medium and high and hash marks in between? The stove top itself is a nightmare to keep clean. Give me back my coil stove any day!!!

I purchased a Maytag dishwasher for $500. After several months of it working less days than not working, I contacted the repairman. I paid $350 to replace the control panel. I wish I had just replaced it with a reliable product. 1 year into ownership and the seals on the door are falling off. May I suggest never purchasing a Maytag product?

My husband and I purchased both a Maytag washer MVWX655DW1 and dryer MEDX655DW1 less than 3 years ago from Sears. We had both the washer and dryer professionally installed. Yesterday, we had an authorized service man come in and look at the problems we were having. He told us our Maytag washer would need a new gear case and gears costing $750.Our Dryer, same age, needed a new cycling thermostat. He said it was due to not cleaning out the lint trap. My husband and clean the lint trap after every load religiously. He said there was a pile of lint built up in the dryer. I could only think this would be a design flaw. To repair the dryer it would cost $350. The grand total to repair our Maytag Washer and Dryers would be $1100. We paid $1082.38 at Sears for both. The only thing Maytag offered to cover was a part for the washer which would cost $640 and we would need to pay the extra $110 for service in addition the $150 diagnostic charge, due to use being out of our one year warranty.We decided to not fix this machine to avoid similar problems in the future. I talked to customer service and asked them to cover the diagnostic charge instead of sending the part, which is far more costly. I got the runaround and 3 rejections before they finally agreed to pay for the diagnostic charge. My husband and I are extremely disappointed in this experience. We currently own a Maytag Microwave and Electric Glass Top Range. We will never buy Maytag again. Our Stove is also lacking. We have the AquaLift cleaning stove. The AquaLift technology does not work.

We bought a washer & dryer from Home Depot 2 1/2 years ago. The control board went out on my washer. I called Maytag and they wanted $109 for a diagnostic fee and wouldnt tell me how much the labor would be. A control board costs $350. So by the time all is said and done... the money would be better spent buying a new one. Maytags slogan of dependability lasts is a bunch of hooey. Washers should last more than 2 1/2 years and Maytag should back up their appliances. They just lost a customer.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

I bought a Maytag Top Loader. I soon discovered that it is not possible to do a cold water wash. After much communication with Maytag Customer Service it was determined that there is no way to bypass it. And it uses a lot of hot water, even on a cold wash. Their explanation was that the water needed to be a certain temperature to make the detergent work effectively. The same detergent that I’ve been using for 40 years with cold water in my Speed Queen. When I need to do a cold water wash, I go to my parents home and use their washer. Disappointing purchase, my last Maytag, for sure.

My son gave me a Maytag washer for Christmas 2013. I hate it. Sometimes it takes me 5 tries to get my clothes washed, and then it dont go all the way through the cycle. I have to constantly check on it. I hate it. Can you give me some tips on what may be causing this... Very disappointed.

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

I have a Model MBF 1958XES4 which I bought from Home Depot in June of 2012. It has leaked repeatedly onto my wood floor. The water also collects and freezes on the floor of the freezer. I already have warped floor boards as a result. I just got it fixed. The repair person said he has done over 200 of these repairs in the last year. He also said Maytag knows its a defect and has supplied them with replacement parts. The company apparently tells its repair companies not to discuss this with their customers. I have yet to contact Maytag, although apparently from others experiences that will be futile. Im willing to join others in pursuing this. I had a 40 year old Kelvinator which was still working well which I replaced with this refrigerator when I redid my kitchen.

I purchased a whole stainless steel kitchen from Lowes and purchased all Maytag products because of the so called quality of Maytag. First we had to return the microwave because it was dented badly. We then notified Lowes that the door on the refrigerator cold cut drawer falls off when opening the drawer. Service man said he would send a new door. Same problem. You can clearly see that the drawer and the refrigerator frame is deformed. Maytag says that the warranty does not cover cosmetics. The range has a aqua lift self-cleaning technology that simply sucks. The oven does not clean! I recommend that no one ever buy Maytag products. They are the worst! I should not have listened to the salesman and bought what I originally wanted - SAMSUNG!!!

I should have returned this machine after my first load of wash; it ruined a couple articles of clothing. Later it ripped a throw rug and just recently ruined a drapery panel. Is there any way I can exchange this machine and rid myself of it? SN: C22534900 Model: MVWC400XW4

I purchased a new Maytag dishwasher (model #MDB4651awb3) for $300, in December of 2009. Seven months later, the dishwasher refused to start. Some lights on the front panel would remain on, while others would not respond. The Maytag repairman made a house call and replaced the front control panel, and vent. After the repair, the dishwasher worked fine for nine months. Then, the same thing happened again. It refused to start with the same front panel light problem. I called Maytag, and since the machine was now past the one year warranty, they wanted $275 for an additional 1 year warranty, to repair the machine. Since I can buy a similar new machine for $25 more, and felt this was now an ongoing problem, (it would be the third panel in less than two years). I expected Maytag to offer more to take care of their lemon problem. Since they refused to reconcile the situation, they obviously no longer stand by their machines. I will no longer buy Maytag/ Whirlpool machines, and do not recommend them.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

Dishwasher Model #MDB7609AWW2 - I have replaced the touchpad once a year for 4 years. Went online and learned a DIY repair using a Permatex Rear Window Defogger Repair Kit to fill in the touchpad broken circuits. I have repaired it once a year for 2 years. My suggestion is to avoid purchasing this product. Apparently even after multiple consumers have contacted Maytag regarding this widespread defect, Maytag has not issued a recall or assisted anyone. They say if the part can be replaced there is no issue. When the dishwasher works, it is great, however it WILL NOT last. Touchpad will fail and you will be out $124 for the part plus labor unless you do the repair yourself.

Maytag MVWC300BW clothes washer makes holes in heavy duty T shirts & sheets. It stretches clothing. We are following directions in loading without success. We are washing everything on the gentle cycle twice to get the clothes clean without destroying them. Today we were stood up for our third service call.

I purchased Maytag microwave model MMV4205AAQ in 2005. I use it infrequently. It stopped heating in Nov. 2011. It must be replaced. But after this experience and reading other comments, I will not purchase any Maytag appliances in the future.

The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.

I bought a Maytag dishwasher from Home Depot August 2018 and it has leaked soapy water every 3 out of 5 times that I run it. Home Depot said they dont cover installs after 2 weeks and to directly contact the manufacturer for service. Maytag sent out a tech 3 times but they werent able to replicate the problem, so nothing has been done to fix the dishwasher even though Ive shown the tech different photos of the dishwasher leaking. The service tech said they will now charge me $90 to return, even though the dishwasher is still under warranty and not repaired! Ive owned many different dishwashers (rentals and houses) without any problems. This is the first Maytag brand and it is horrible. I will never buy another Maytag and have warned all of my friends and family.

Fire Danger. We had a power outage and my Maytag gas range/double oven (Model: MGR6875ADS) was dead after the power came back on. We figured it was the control board and braced for the expense to replace it. A few days later, I plugged the oven back in just to see if it would work and it did! The control panel came back on and we were up and running. The good news end there. On Christmas Eve, we came home to a house full of smoke with fire alarms buzzing. A butcher block style cutting board that was on top of the range with Santas cookies on it was on fire. Twenty more minutes and the house would have been gone.

I bought a high capacity Maytag Bravos washing machine, thinking it would be better than the ones that shred your clothes around the center post. Wrong. You still have to wrap your clothes around the edges as if there were a post, and even then the machine will become unbalanced (after much thumping and crashing), causing it to stop, which forces you to redistribute the weight, sometimes several times in one load of wash! I called the company and got nowhere -- I wont say nowhere fast because it took forever to get nowhere. I do not recommend this machine.

The only reason I am giving 2 stars is because I didnt actually spend my hard earned money buying these machines, they came with our house purchase. At first I was excited to have a good quality washer/dryer... Now I understand why the previous owners left them behind. My complaints are like most of the others on here - takes way too long to do a load because of the stupid water sensor, it doesnt wash loads evenly so everything on top hardly gets wet and washed properly, lint all over our clothes, powder residue left behind even though I set it to 2 rinses, a lot of settings but missing useful ones like quick wash... just all around disappointing. At least one good thing has come out of this and we will not be buying Maytag for our new laundry room. Saying that I have also read so many bad/worrying reviews about Samsung and LG - cant any company make good, reliable, lasting products and stand behind a warranty anymore?!

Maytag Front load washer mah8700aww - This washer has been the biggest boat anchor of a machine. Nothing but trouble and bad parts. New motor after 18 months, water level sensor at 2 years, main control board twice now at 2 years and 4 years, and now it is showing signs of needing yet another main board. E3 trouble code plagues our home and basement. This machine has been leveled and re-leveled numerous times and still shakes like crazy... I mix my paint cans by setting them on the top... the best use for this machine. Yes it sits on a concrete floor. So not satisfied and will not ever buy another Maytag anything. There should be a negative star rating. It does not deserve even 1 star after being taken advantage of like we and thousands of others have been.

I have had my washer and my dryer (model no. MGDB850WQ - serial no. MJ3311087), for 1 and 1/2 years. I have given both plenty of time and since the beginning, I have literally hated these products. This was a large purchase, so I feel locked into a terrible choice. I wish I had never bought these two items and will never use Maytag again. I will also never recommend these products to anyone. I do not like the new technology.

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

Maytag Bravos XL - I purchased my maytag washer & gas dryer on 5/12/12. In Dec 2012 the heating element went out. I had to wait a week for a repairman to come out on Dec. 20 to fix it. Now for the second time on Dec. 30th, 2014 the heating element has gone out. I called for a repairman to come out. I have to wait until Jan. 12th 2015 for service. I have 8 people in my home including 3 grandchildren. This length of waiting is ridiculous and very inconvenient.