I bought this large capacity top loading wash machine about 22 years ago and it has yet to fail me. It had never needed any repairs and cleans my clothes wonderfully. The brands reputation is well earned. Great washer!

The low water usage design is horrible. Clothes dont get clean as it doesnt use enough water to cover them. Takes twice as long to do a load as our old washer. Took about 1 1/4 hours yesterday for 1 load using heavy which is the only setting that uses more than a thimble of water. Should have looked for a commercial type with a real agitator and adequate water usage. Not saying Maytag is probably any worse than any other brand of new efficiency government mandated garbage washer, but its no good.

After first dishwasher was recalled, this one (installed less than 4 years ago - Oct. 2010) had the electrical panel burn out - two years ago. Now - for second time. LAST TIME BUYING A MAYTAG!

Model MBF 2258XEW3. I am very annoyed with this fridge. Never will buy a Maytag again. I went to this site to see what the problem with my fridge was and read that I am not the only one with this problem. From the beginning it never worked right. Often the food in the fridge got ice crystals in them so I had to up the temp. This made the freezer not cold enough so I had to lower the temp again. This is a constant affair. Now the bottom of the freezer is collecting an ice sheet or a water bath that has to be removed every other day so that it doesnt built up or leak out. Will have to buy a new fridge. But now I am worried that I might buy another lemon.

I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

WARNING FIRE/HEALTH HAZARD - BRAVOS MVWX500XW1. Purchased it new 2011. Never cleaned well. Some clothes came out with dry spots, darks had soap scum/lint spots over them. On several occasions, clothes were not wrung out properly. BUT when I went to do a load of laundry recently, I heard a loud POP and almost instantly my entire basement filled with an acrid, dense grey smoke coming from under the machine. I am concerned toxic chemicals were released. People still smell the odor in the house. Need to get in touch with company again after the weekend to see what they will suggest.

French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!

My built in electric double wall oven, Model MEW6630DDB, convection on the top, has been the most frustrating appliance I have ever owned. It has never kept an even temperature. It has been repaired several times and still does not keep an even temperature. It takes 14 hours to cook a 20 lb. turkey and baking cookies are not even an option. I have complained to Maytag and have paid for repair services. Their solution buy an extended warranty which is absolutely insane because they havent been able to repair it since it was new over four years ago.

I purchased this Maytag Bravos machine because I was told it can wash large loads and is one of the best washers out there... Both are so far from the truth, this is the worst machine I have ever owned. The water level is almost none. And my clothes come out dirty and I have to wash several times to even get them semi cleaned. I am not rich and trying to save enough. To buy this machine was not easy and I am now with no options. I called Lowes after a couple day after I got the machine and told them it is not working. They sent me another machine yet it still does not clean my clothes. I wanted to return it and get a better machine but they refuse to allow me to do so because now it is 2 months old and past the 30 day return. I purchased an extended warranty which is useless cause. The machine is junk even when working as it should... I will never buy from Maytag again because they refuse to back their crappy product and refund my money. I would tell anyone looking for a washer to not go with Maytag. They are terrible machines and a bad design... I even contacted Maytag and was pretty much told too bad and just rewash my clothes as many times I need but they will not do anything to resolve this issue. TOO bad is what I was told...

About 4 years we purchased a dishwasher model # MDB7749AWM2 made by Maytag.The first part of Aug. 2015 it quit working. I had a repairman look at it and he said it was the control panel and he would order one. He ordered it and we waited a couple of weeks, no part. He called about it and they told him Sept. 9th it would be sent. Sept. 9 came went and no part. He called them again and they told him they had no record of the order. So he ordered it again in few weeks, was told it was back-ordered. This happened a couple more times and I told him to cancel the order. I would go buy a new one but not a Maytag.

I bought all new Maytag appliances for a new house built 2 years ago. The oven fan, while in warranty, began coming on in the middle of the night. It would turn on, cancel, began not working, and then the ticking noise began. Maytag sent 5 different service people out, sometimes without the part. We are afraid to use it now and have turned off the breaker for it. Now, it is turning itself back on again. Maytag says we must now pay for any repairs/service calls as it is out of warranty. It was not out of warranty when all these troubles began.I called Maytag customer service today and could not have talked to a less customer friendly person. She didnt care that it was in warranty when the trouble began. It is out now and is our problem. There is no one else but her we can talk to about it. She is the decision maker. What experiences has anyone had with trying to call the president of Whirlpool, or filing a small claims court action? Any help is appreciated. Who is going to cook our Thanksgiving turkey?

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

We have a Maytag Dishwasher Model MDBTT60AWB purchased from Lowes about 8 or 9 years ago. This model was included in the huge 2010 recall of 1.7 million units due to the possibility of heater-unit fires. For the last couple of years, its had a problem staying on the selected cycle: After being started on normal wash, it reverted to rinse only after a few seconds, but eventually quit responded to the selection of other cycles altogether. Removing the back from the door to expose the innards revealed the ribbon cable that connects the circuit-board head to the control panel had worked loose. Reattaching it provides a temporary fix, but it eventually works loose again. We suppose the screw holding the back to the door will strip sooner or later, but by then well probably be so fed-up with fixing it that buying a new (non-Maytag) one wont seem like a bad option.

Bought new and only had one service call in 20 years. The control panel was replaced. Since then, the dishwasher has performed well and, factually, was far less expensive than many other models! That figured in our decision when remodeling our kitchen back then.

I purchased a Whirlpool oven. It is still under warranty at present. I used the self-clean oven feature just before Christmas, it wasnt that dirty but I wanted to have it clean for Christmas. The glass panels on the door had no stain or grease on it, until I used the self-clean feature, and now there is black staining inside the glass. This oven is not even 9 months old, and you cannot clean in between the glass. My second complaint which I believe is a very poor design on Whirlpool’s end is that the steam vents are very sharp. When I went to wipe off the black splash panel just under the vent tube, I cut my baby finger twice!!! And it is impossible not to slice your pinky. I have been working with Whirlpool since this happened, and they finally issued me a new stove. I was to go back to where I purchased this product and pick another stove. So I did this yesterday and checked out all the Whirlpool stoves because the store says I have to purchases a Whirlpool. But every Whirlpool model has the same sharp steam tube vent, and I am presently waiting for the store manager to speak with his higher ups to see if they will let me pick a stove made by a different supplier. I’m actually really shocked to learn that this could end up being a battle especially after I took the manager to every stove in his store made by Whirlpool and showed him each of the vents and just how sharp those vent tubes really are. You would think he would want to be aware of this and deal accordingly. So I post this to warn any potential customers of Whirlpool to check that steam vent on the left side of the stove, and stay away from it as it is very sharp and you can’t help but cut your pinky finger when you wipe across the stove.

We purchased our Maytag dishwasher from Nebraska Furniture Mart in February 2013. The touch panel on our Maytag dishwasher quit working in December 2014, several lights would come on or flash or not work at all. The first repairman that we had come out took the panel apart, cleaned it up and put it back together ($100). It started working again but a few days later it started doing the same thing again. So I called the repairman back and he said the touch panel would need to be replaced. He called all over Omaha and no one had the part in stock. He called the Chicago Maytag warehouse and was told by them that they were out of them because there were so many defective dishwashers that they used them all. Now they are trying to find a new manufacturer to make them. It could be months before they get them in. So I contacted Maytag and of course they said that is not true and put me through to a parts company that they said has all the parts available. When I told that company that it was the touch panel, I was told by them that you only replace the touch panel for cosmetic reasons! So we got a second opinion from another Maytag repair company and he spent about 10 minutes looking at the dishwasher and said its a defective touch panel. He said he has replaced a lot of them in Maytag dishwashers. He recommended that I contact Maytag customer service and try to get them to pay for the part. I did call them and of course they refused because it is out of warranty. The supervisor even told me that they have not had any complaints about the touchpad malfunctioning! They do not stand behind their products anymore. I will never buy a Maytag or Whirlpool product ever again. I told them exactly how I felt and their only reply was Im sorry you feel that way. I am surprised they continue to stay in business. I dont understand how major stores can continue to sell their products when they are garbage. Based on the other reviews Ive read, Im not even sure we should fix this for $250.

I just finished paying off my Maytag Bravos series washer and dryer, and now they are failing! The washer isnt getting dirt out and the dryer power button broke. And its not like I can use some pliers to get the switch to work, its like the part that controls the power just dropped out of existence, leaving me with a knob in my hand that connects to nothing! Of course, the limited warranty only covers the drums, not the little dinky parts that break more easily. I had inherited a set of Maytags and they were well over 20 years old (possibly 30) and they both were powerhouses. But this is terrible! I feel super disappointed that Im going to have to buy a new set after only owning these for 18 months. I know I WONT be buying Maytag ever again, though!

I have had my washer and dryer for 14 months and from day one, my washer eats holes in my clothes. It is always the bottom center front of my shirts. I complained about this and was told it was my clothes. They were either old, or the type of fabric, or too much bleach, etc. etc. Everything was wrong with myclothes except the washer. I purchased a new shirt and washed it without ever had worn it, and when I took it out of the washer, it has holes in the front. NOW YOU TELL ME that is the shirt and not the washer. I have used Maytag for the past 40 years and I never had any problems with the old Maytag washers. This new Bravos is a piece of junk and I am sorry I ever purchased it. I will never buy another Maytag product.

Purchased washer less than 2 years ago. Loud noise like a jet engine or helicopter in spin cycle. Did not purchase the extended warranty. Called Whirlpool/ Maytag customer service. Was told I could have one of their repair people come out. I would have to pay $300 which would give me the repair and extended 1 yr warranty, or I could get $300 off toward a purchase of a new washer. Are you kidding me? This washer wasnt even 2 yr old and making this horrid noise in the spin cycle. I had to have a independent repairman for Maytag washers come out to tell me it wash the bearing and would cost 3 to 4 hundred dollars to fix it. I said no thanks and after his $90 service call am stuck listening to this piece of junk make noise till it completely breaks. I will never buy a Whirlpool product again or recommend one. Whirlpool you sell nothing but junk.

We purchased a refrigerator in December 2013. It quit working less than 8 months later. The company contracted to repair it made us wait 4 days for service; they did not repair the unit. We are now expected to wait another 4 days for them to return. STAY AWAY from Maytag!!!

I am very dissatisfied with this Maytag Gemini oven Ive had it for 4yrs. It has been in the shop twice for the same problem. Temperature control. It is down again for the same thing temperature control. The repairman, who I had to look at it, says the bill will be over $500.00. I paid $1300.00 for this stove. I cant afford to put any more money in this stove. I had to pay $100.00 for repairman to tell me this. The model # met8665xw02 serial#D30522404. Is there a recall on this stove? There should be. I sold Maytag products for several years at Circuit City. I always pushed Maytag instead of another brand. I believed in Maytag. The repairman hasnt been lonely to me.

If the control panel light on your Ice2O refrigerator starts flashing you will learn about the Non-Customer Service of Maytag. The problem is the High Voltage Control Board. Maytag has been aware of this defective part since 2007. At one time Maytag was fixing these at no cost to the customer via a recall. Then conveniently in 2011 the Japanese tsunami wiped out the only plant in the universe that manufactures the part.Now out of the goodness of Maytag’s corporate heart they offer the customer $300 off of a $2300 replacement (Oh, I am so grateful). It is time for Maytag (Whirlpool) to accept responsibility for a defective product and recall this refrigerator with a replacement. In the meantime if you have this problem, my advice is to go out a buy a non-Maytag/Whirlpool product since Maytag/Whirlpool cannot be trusted to stand behind their products. Please share this post with family and friends to prevent others from experiencing Non-Customer Service.

I bought a Maytag dishwasher, when I bought my house (7/2010). I live alone and I use my dishwasher only once a week or once every two weeks. After 3 years of working perfect, it stopped working. I had someone come look at it. After troubleshooting with the basic steps, making sure the water was correctly hooked up, a fuse was not the problem. The dishwasher door was shut completely. He took the racks and all movable parts, & thought something, a piece of glass, etc, was stuck in the drain. Nope. After reading these reviews I realize it is got to be the control panel because the start button will not come on and all these people have the similar problem. It just stopped. Period. The panel lights come on, but not the stop button. I am a single person as stated and on disability and on a very tight budget. I bought a Maytag because of the name and reputation. How long would it have lasted under normal use, say a family of 4, using it nightly? Certainly less than a year. I have no idea what to do now. I cannot afford a repairman, & I am certain it is the control panel on the dishwasher. I do of course have all the model numbers, etc & papers, when I bought it. I can provide proper paperwork, when contacted.

A washer should last 10 years. Bought it in 2009 - after two years we spent $200+ on seal and bearings. Now, in 2014 we need more seal and bearings and the service tech recommended by Maytag says the cost will be $500+. Machine has a serious design flaw, and bad parts, and bad service.

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

Maytag 6.2 Induction Freestanding Range Model MIR8890AS0 F47 - I am a very careful shopper. I spent many, many hours researching and searching for the best value. It took me over 2 weeks of research to find an induction oven we could afford. We are a family of 3. Normally, we use just one burner for dinner. We bought the range in Feb 2013. On August 5. 2014, we had company over for dinner. I used more than 2 burners and the oven at the same time and the right 2 burners quit working; I now have the dreaded F47 code. I have had numerous Maytag Authorized repairmen out. They ordered every part except for the one that was necessary to fix my stove. I purchased in Feb 2013, burners went out 8/5/14. This is only 18 months old and is JUNK. Arent our landfills full enough?Maytag customer service is awful. I spent hours on the phone, mainly on hold, in efforts to get help. Maytag claims to have such a great 10 year limited warranty but they wont warranty this F47 issue. Thank God I bought insurance with an outside company. The wrong parts that were ordered were at least covered by my own insurance policy; no thanks to Maytag. I am angry that I have to search all over again to try and find the right stove. I am now fearful of induction. I invested in a lot of induction cookware which was an added expense and burden! They need to stand behind their appliances!People cannot afford to waste thousands of dollars every 1.5 years to cook their meals! This has been an extremely unpleasant issue. It has cost me many hours of waiting for repairmen, waiting on hold, getting and storing many wrong parts ordered by repairmen. I calculate this cost me over 50 hours of my life on the F47 problem. Not to mention the time it took me to shop for this junk to begin with!I think they need to recall this issue as it is clearly a design flaw. I researched this and found many other owners had similar problems. The F47 means that the user interface isnt communicating with the range (the circuit board). They placed the circuit board under the burner surface area, sandwiched between the burners and the oven. It was just a matter of too much heat before this board shorted out. The cost to replace this board is over $600. I am afraid of investing another dime into this machine. I wasted time, energy and A LOT of money on this inferior product.

Can not wash 4 pairs of pants or 2 sheets because they get out of balance when the spin cycle begins. I had to take the clothes out and move them around to keep the balance. Very unhappy. Would not recommend this washer.

Well, Im confused and nervous! Ive read the reviews and I LOVE my Bravos washer - cleans unbelievable, its quiet, no rattling of pipes. My daughter was highly impressed when she was visiting with her daughters. She told me my washer got stains out of her kids clothes that her washer could not! Im confused because of the number of bad reviews for this washer - maybe they changed the washer? Mine is about 3 years old and I am SO happy with it! No agitator, but cleans so well. Terrified if it dies on me, I wont be able to replace it.

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

Dual oven - one is a convection oven. Never used the bottom drawer so that was wasted on previous range. I purchased a white appliance to match my others. The white stove top is a pain. Too bad it wasnt black. I checked this model online and found a good price in the city. I contacted the local Home Depot and they did a price match less 10% - all a bonus. The ovens work great although I have not tried the self clean. I have read that similar models have problems related to the self clean feature - high heat and circuit boards. My plan is to have a fan directed at the top of the stove when I use it and the range hood fan going. The convection oven is great - hard to mess up a recipe with that. The dual ovens are truly a great feature - strongly recommend. The keep warm is great also - nice to have two things cooking at the same time. That being said - the bottom oven is low, but that is worth the extra cooking space.

I purchased an Atlantis washer in 2005 and assumed that Maytag was still one of the better manufacturers. How naive of me! What genius at Maytag thought it was a good idea to place the water filter inside the washer? Not only can you not keep the filter clean so that cold water will flow properly, even worse, if the filter completely clogs, the water will not stop filling into the tub which could, of course cause an overfill and flood. I narrowly escaped this scenario once. No one should have to stand and watch their machine fill with water to insure it stops. Now the machine is causing a grinding noise when agitating. I expect it to stop working any day. I will not buy another Maytag or Whirlpool, who of course now owns Maytag. And I will not pay another repair bill for the filter or any other part. The brand was once considered the best in America, now its just another brand thats a piece of junk produced in another country.

Maytag top load washer. I dont understand why Maytag would make such a piece of crap. It takes so long to wash, that I can only wash a couple of loads a day. It doesnt fill. It doesnt get the clothes clean. My electric bill is higher. Its so noisy too. Never thought Maytag would make such garbage.

I bought a Maytag range (MET-8775) last year, because my wife loves to bake and wanted the double oven. The oven never did brown properly, despite trying different temperatures and cookware. So, I called the 1-800 number in the manual. I was told they would have a technician come out and check it, and they assured me it was under warranty. The technician arrived, and since it was close to the end of the warranty period, I showed him the receipt for purchase. I got another assurance that this visit was covered by the warranty, before anything was actually done. Well, he checked it out and eventually calibrated the temperature. That helped a little, but still, it doesnt brown very well. About a month later, I got an invoice from the service company that dispatched the tech telling me Maytag will not cover the visit under warranty. After a long call with Maytag (now Whirlpool, I believe), I was told that since the calibration instructions were in the manual, it wasnt covered! Well, why wasnt the thing calibrated to begin with? And your average customer is expected to have an accurate thermometer/gauge to set it and know whether the temp is off or not? Why was I told twice that it would be covered? If either the lady on the 1-800 line or the tech who came had told me this wasnt covered, I would have argued a case right then. As it turned out, I had no choice but to get billed for something I was assured was covered. And as I said, it still doesnt brown right; and we had tried different temperatures before. We are preparing a major kitchen remodel, and its hard to believe that Maytag/Whirlpool would so thoroughly piss off a customer and potential future customer over an $80.00 service call.

Purchased this washer from Saginaw, Michigan location in 2007. Started sounding like it was going to come through the wall of the laundry room so I contacted repair service. Told bearing was bad and that cost of repair would be $1,000.00 - literally laughed at repairman. I find it difficult to believe that a washer is built to last 7 years after paying so much for it.... My years of purchasing solely from Maytag have thus ended.

I made the mistake of buying the stainless steel bottom freezer (model# MBL2258XES1) approximately 1 year before the freezer started to make a periodic clunking sound. The repairman responded because my year warranty was still active and found no cause for the noise. Fast forward a couple of months later and it started pouring water out onto my hardwood floors!!! Unfortunately it happened while we were away and my floors were destroyed. Maytag wants nothing to do with me. Im so disgusted. I now have to have a towel permanently on my kitchen floor. Nice. I made the unfortunate mistake of buying an Amana dishwasher recently not knowing that they were also owned by Maytag. The dishwasher is a water waster :( This is very disappointing - you try and buy American and you get screwed. If any lawsuits start up, sign me up!!!

I have a Maytag Washer and Dryer that I am very happy with. I have had both of them for about 6 years. I had a problem with the soap dispenser not working properly shortly after I purchased them, but a service technician came and fixed that within a few day. I will probably stick with the same brand when/if I do have to replace them.

Bought our washer dryer set from Sears in the fall of 2010. I had reservations from the start as the machines were new and the salesman was really pushing this set (on sale), with all the customers, even offering extra discounts on these models only, if customers bought that day. Apparently, they had overstock and were trying to sell them all ASAP. That was a warning to me but my husband convinced me that I was being overly suspicious. We had previously owned Maytag machines for 20 years and loved them. So I agreed. Well, I have been cursing that decision ever since. You have to hand wash/prescrub any stain on clothing, even a little make-up like blush or a little mud. Then you have to put up with an inflexible system that wont allow you manual options regarding spins and temperature or times, etc. Its all programmed. Then you put up with clanging spin cycle as it bangs against the wall. Then you pull out very wrinkled and not always cleaned clothes only to begin the most frustrating dryer experience ever. It has a mind of its own. It can actually keep spinning as it keeps adding dry time and the clothes never dry! God help you if you have a regular load. All your clothes will get stuck on the little ledge. They stay there in a heap as the machine spins and spins.The solution? You have to add a bunch of dry towels to create a lot of mass so that it keeps your laundry from getting stuck on the side. Then you have to repeat this several times cause it doesnt dry well. I will never ever shop at Sears and I will never buy Whirlpool or Maytag again. I am now saving to buy another set.

Overall- I think washers aren’t made to last like they once were. Growing up- we had the same washing machine while living at home. It seems now- they only last 10 years if you are lucky. They should make more longer lasting machines.

WORST MACHINE EVER! Besides the soap scum Maytag Bravos XL Washer leaves on all of our jeans and my husbands work pants, the machine decides when it wants to work and when it does not want to work. Weve had repairmen over, we have called the 800 numbers, just like all of the other reviews on here. Ive readjusted clothes in that thing more than Ive done laundry in my life!!! I HATE this machine. Ive memorized the manual from reading it so many times, have the correct detergents, tried washing large loads, small loads, lined up the clothes around the outside so the middle thingie is not covered, thrown clothes loosely in there. Every way possible. The machine senses, starts filling, then just stops. Today, no matter what I do with the load in there, it will NOT run, it keeps shutting itself down and I do not even know what else to do. NEVER EVER EVER buy this machine! We will never own another Maytag EVER.

My wife and I bought a Maytag Bravos at the suggestion of a store employee at Lowes. Since we have owned it, I have seen the reviews and the washer has been a total let down. We have experienced all the same complaints. Loud noise, door lock not working, not enough water in the drum to wash clothes, and the bearings going out and it doesnt work. NEVER will we buy a MAYTAG again. To the scrap yard I go today. Thanks MAYTAG for wasting my money. Thanks LOWES for recommending this garbage.

First we bought the washer and not even a month after it was ruined. In the span of the year that weve had it, it has broken down about three times. Then we bought the matching dryer in August and by the beginning of December it has broken down. Called customer service and they are not coming until January 18. Have me waiting over a month to fix it. Worst brand ever and even worse customer service. Never again will I buy anything from this brand.

Never had a better washing machine, highly recommend this product: MVWC425BW. Saved plenty on water usage, no rust and no service issues after 6 months.

I feel its kind of cheap. The interior is all plastic which doesnt look shiny and clean as it use to be when it was new. Not efficient in cleaning. Can see still dirt spots in some of the washed dishes.

I had a stroke last year in August and my children got together and bought me a washer. And after the third use this thing started messing up and I had to call in someone. Now the warranty is up and I am sitting here with a new broken down machine.

My wife told me yesterday she was getting a f51 code... went on you tube and took the top off and the clothes holder out, found 1 quarter and 3 dimes... put it all back together... same thing... took the back off... hoses off, unplugged it and the allen that holds the motor had backed out... no more maytags for me... Tightened the allen, all is fine for now... my opinion, this should never ever happen... No lock washer anything engineering to prevent this from occurring... My grade: replace the engineer...

Clothes are never submerged in water. Clothes come out worse than when they went in. Every review and complaint mentioned is dead on! This Bravos XL is a piece of crap. Stay away from lying salesmen from HH Gregg. And stay away from Maytag. Perhaps we should all get together and file a class action lawsuit! And donate all monies, washing machines and dingy clothes to charity!

This washer has no agitator post and doesnt seem to clean as well as ones with agitator posts. I have heard that they are easier on your clothes though. The dryer works well enough, but I believe the control panel/motherboard needs replacing. The signal sounds even with the dryer turned off, which is startling to my dog and me. I reset it by flipping off the 220 breaker in the garage and leaving it off until the next time I do laundry!

Maytag Neptune was purchased over 15 years ago to replace GE, which we purchased when children were little. I wanted a step up in quality. I remember paying around $499 for this unit. This is an analog unit. The intellidry feature has been a real asset, protecting our clothes from over drying. We have had this machine for nearly 20 years. It has been real reliable, sometimes drying 20 loads a week. Large capacity, but has to fit down a narrow and twisting stairway. Must be energy efficient, have good reviews and decent price. We always look for sales or buying incentives. Brand is secondary to quality. Knowledge of an appliances historical reputation is important. I would look at reviews, especially concerning cost of repair. I would attempt to get a hands-on view, before purchase from a reputable supplier at the best price. My dryer has only required one major repair in the time Ive had it. A few years ago we replaced the motor and blower, and I have personally replaced the drum support rollers twice. I hesitate to replace this machine, because the analog controls have proved very reliable.

I purchased this set 7 years ago and the washer started stopping mid-cycle and the dryer sensor doesnt work. I called the Maytag service number and after several phone calls (they had my name spelled incorrectly and the wrong address), was able to schedule an authorized servicer. He said the motor and motor controller needed to be replaced and it would cost over $900. When I said I expected my $1,200 washer to last more than 7 years, the service person informed me that the machines were made by Samsung (not Maytag) and just carried the Maytag label. He said the Maytag Neptune washers and dryers were the reason Maytag went into bankruptcy and was bought out by Whirlpool. I am disappointed Whirlpool/Maytag does not stand behind this product and will not buy this brand again.

Eighteen months after purchasing the Maytag Bravos, I had to have the motherboard replaced. Maytag offered nothing except a list of names for repairmen in my area. Now another 18 months later, the washer gets out of balance (this is a self-balancing machine, supposedly) at least three or four times for every load. Since it is all electronic, you cant select a spin cycle without the machine adding more water into the tub. Again, this does not self-correct the out of balance problem. Trying to balance the cloths several times during a wash cycle extends the length of time it takes to wash one load on average two hours. Maytag offers no customer service or customer support. Im sure their call center is not located in any part of the United States. I will never purchase another Maytag appliance.

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

My Maytag (MDBH955AWB) dishwasher (not even 6 years old) is losing its prongs that help the dishes to stand up. They are corroded at the bottom and snap right off, leaving the dishes without support and banging into each other. We are only a family of 3 so it gets moderate to minimal use. The bottom basket costs $200 to replace, a third of the cost of a brand new dishwasher. Everything else about it is fine but my dishes will be chipping away. I cant believe Maytag made the basket so poorly that it doesnt last the lifetime of the dishwasher.

I have a new HE (high efficiency) washer. It takes getting used to as its a definite change from the old agitating system but I think I like it. It doesnt make much in the way of suds but everything still comes out really clean. The wash cycle is much longer than my old washer but it uses a lot less water.

Maytag is the brand I had for 18 years and never had a problem with the washer or dryer in all that time. So when my dryer died I decided to get a new set of Maytag washer and dryer. I picked the set together and they dont have a lot of bells and whistles, simple to use and the washer is an HE. Cost was about $900 for the pair. I bought the washer and dryer in May of 2015. Models are simple to use. I have not had any problems and quite pleased with the work they do.I like to stick with a brand if it has served me well. Energy costs need to be low and I look for sales. Capacity is something I do not need a lot of, since it is just two I am washing for. Good quality is what I look for. I have not ever had paint chipping or rusting. Never had socks missing or a bad result with cleaning or drying. The washer has a cleaning cycle and the dryer is very easy to clean, the lint filter, and I get great results with no static when I take clothes out of the dryer.

I purchased a Maytag washer 5 months ago. I noticed the washer was not putting enough water in the machine to cover my clothes, and at the end of cycle my clothes would be all tangled up. A repairman looked at it and said there was nothing he could do. Do not buy this washer. It is a lemon. I even spoke to the main customer service representative, he was the most arrogant man I have ever felt with. He basically said deal with it. I want. I want my money back so I can purchase a washer that actually works.

I had a Maytag dishwasher for 17 years, and it has still worked fine when we moved to another state. At the end of 2010, I bought a new Maytag (1) because my old one performed so well and (2) we left it at our old house. Well, slightly over two years later, this piece of junk (Model MDB6709AWAQ1) needs almost $300 worth of repairs. The repairman said they are no longer made to last and have been that way since about the year 2000. All of the inner workings are run by electronics which only last about two years. I said, What happened; the Maytag repairman got tired of sitting around doing nothing? I would never ever purchase another Maytag dishwasher, or any other appliance made by them or Whirlpool which took over Maytag.

We purchased Maytag dishwasher model #MDBH989AW53 in January 2010. June of 2012 the control panel died. Luckily, we had the extended warranty. The service company came and replaced the panel. 3 weeks ago, the panel died again! The service company replaced the panel again. Today I got home and the dishwasher is completely dead! I am so furious!!! At this point, I may just have to bite the bullet and buy a brand new machine. This should NEVER happen to an appliance that is so new! What a laugh regarding the Maytag quality! It is the WORST I have ever seen in my life! Stay away from Maytag!!!! Buyer beware!!!!

I have a Maytag side by side. In the first year, the ice maker failed and I had to replace it (in warranty/no charge). In the fifth year, the compressor failed (no warranty) and it hasnt been replaced. Since then, I have been looking at reviews and warranties of new refrigerators. The warranties (unless you want to pay $3,000+) are all one year limited. The reviews are scathing and it doesnt matter what brand. My question is, why dont you/we all get together and file a class action suit and demand millions in damages? Complaining wont get you anywhere with these people; however, hitting them in the pocket book will make them pay attention, especially if the penalty is severe enough.

Bought a Maytag Bravos x MVWX700XX1 about 2 years ago and now the agitator barely moves and makes a very loud grinding noise. Never had a major appliance wear out so fast..is a piece of junk. Will never buy another Maytag product ever again. Their old ads about the Maytag guy being bored because he never needed to fix anything should be considered false advertising.

I purchased this oven in April 2015. I have had nothing but problems with the unit. The temperature is off. I have had the probe replaced in July and will be done again next week (January 26, 2016). The AquaLift self-cleaning feature does not work. I ran the self-cleaning feature about 8 times and back to back on several occasions. The service providers stated that it really doesnt work and there is nothing they can do about it. The front of my oven, above the vent, is stained from the oven exhaust. They said there is nothing they can do about that either. The last service company that came out for a service call to check the oven temperature came without the proper tool to check the temperature and ended up snapping the propane line. I was given 6 month of a free extended warranty for my inconvenience and told that the company does not replace models. They will continue to come out and repair them. I will never buy another Maytag appliance again.

My Maytag Dishwashers (MDB7749AWW1) control panel failed for the 2nd time. I replaced it several years ago, but this time the part cost was almost double. So instead of a recall they jack up the price to capitalize their mistake. The ribbon cable gets rusted at the bend from the steam over time. No Whirlpool or Maytag or any other products they market.

I chose Maytag because they received a good rating from Consumer Reports. I liked that they were for extra large loads however now that Ive had them for 12 years I know the large loads are no more than my old Kenmore washer and dryer. The real deal breaker for me is the size of load that you can actually wash. I was hoping I would be able to wash a blanket without worrying about the washer going off balance. My washer and dryer are Maytag although I dont know the model number. They are full size but the extra large load is not extra large. The knob on my washer broke and Maytag wanted $15 for a plastic knob! I found it on eBay for $3. The washer goes off balance too easily.

Maytag Dryer- Bravos XL - Waiting for my third service call since purchasing my dryer less than 2 months ago. After 2 service calls the repairman found a piece of the mold that should have been removed at the factory causing problems. Now, my dryer made a weird noise, sparks flew and it no longer works. After calling the seller and the manufacturer requesting a replacement, they feel it should be repaired (again).

Bought a Maytag dishwasher early July. Worked great for 3 months. Drain pump went out. Called customer service, 30 minutes to get a person. 1 week to get a service tech here. Even though we told them pump was out. Sent with no repair parts. So has to come back at our inconvenience, company policy, not service tech fault. Tried to complain on live chat. 30 minutes for them to get with me. Still no satisfaction. Would not recommend the product for the company itself. Sadly thought we upgraded.

I have owned two Maytag washers. Top load and front load. They have been the biggest piece of garbage I have ever purchased. My current front loader eats and destroys clothing. I have had to throw out numerous clothes as the machine simply destroys them. I have also had numerous problems with Maytag washers. The wiring is garbage. Couple yrs after purchase the washer shorted out. Im handy so I took it apart. Discovered a broken wire. I had to rewire a new connection with as. The wire used in manufacturing is so thin its line a strand of hair. Now it leaks under the drum. I had to place a container under the drum to collect the water. My other purchase was a top load. The lint was just a nightmare. Maytag sent me some contraption after numerous complaints that was suppose to assist in the collection of lint. Again, a piece of garbage. DONT BUY. Save your MONEY.

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

We bought a new Maytag dishwasher MDB7609 as part of the 2010 recall. Within the first twelve months the black skirt at the bottom of the door collapsed to the floor. It was in small pieces and brittle as though exposed to excess heat. The repairman fixed it free but made the point it was not covered under warranty. Next the heated dry cycle baked the water onto the dishes forming a white crusty layer. We have a water softener that works very well. We stopped using heated dry because it is too hot. Last night before bed, I was standing in the kitchen and I smelled something burning. My wife had mistakenly programmed heated dry into the cycle. Obviously this dishwasher is as much a fire hazard as the one it replaced but no recall has been issued yet.

Maytag Bravos electric steam dryer purchased 2009 - I have had to replace the door hinges within one year of usage at my expense. The blower belt and pulley had come off twice, the last time about a half hour after the repairman (again at my expense) left. I put it back on myself and if it comes off again, I will use Locktite to glue it on the blower shaft. I figure I will be lucky if this crap lasts a couple more years anyway. No more Maytag for us! What does it take for the consumer to get some representation with regard to lemon laws here? I will take my wrath out on Home Depot here since I have no recourse. If enough people complain, maybe they will stop selling that junk. I also will disregard Consumer Reports in the future.

When I went to use this machine (maytag bravos). I noticed there was like a 1/4 filled in tub, checked water flow, that was fine. Then read the manual that Maytag sees using Less Water is better for clothes, I always thought it was less detergent, ohh well. Wouldnt recommend this item to anyone.

My dishwashers warranty expired in March 2011 and it stopped running in April 2011. I have not had the use of my dishwasher since then. I was able to finally afford to have a technician take a look at it. I am told that it is the circuit board and it is going to cost as much as the price I bought the dishwasher for. I thought Maytag products were better than the other products so I paid a little more and got a Maytag only to find out that they are garbage. I might as well bought an unknown brand at a cheaper price for all your products were worth. I guess you cannot trust anyone these days, and I will never buy a Maytag product of any kind again. I think that you should fix this.

As all the other reviews day 1 Dryer had no heat, washer unbalanced and knotting all the clothes. Sent out new dryer after trying to fix to no avail. One month after new dryer, normal cycle continues to run and not turn off. Repairs again - new computer board. Now washer is winding high pitch noise level - repair new bearings. Thank goodness for warranty. But washer and dryer act up again. I purchased extended warranty. Washer tub needed replacing because transmission went out, dryer again control panel problems. Last night the dryer started on FIRE. I’m sure because the control panel normal was not working again after it was replaced less than 2 yrs ago. Total time owned 6 miserable years. Going back to basics, ugh....

We got our Maytag dishwasher in 2011. Weve experienced a lot of the same problems other people have mentioned. Control Panel was the first thing to go out. Now it has a foul odor coming from it and it doesnt get the dishes clean. The heating coil has stopped working and is rusting. This dishwasher is junk and Im very disappointed. I will never buy Maytag again nor any company related to them.

Maytag BRAVOS XL Washer - The worst washer I have ever used. Do not buy! It does not use enough water and leaves a white scummy residue on dark clothes. You have to wash them all off in warm water and then send it through one or two more rinses to get it washed off. I may as well do laundry by hand! Absolutely disgusting!

The washer 4 years ago we had the control panel replaced at our expense. Now, control panel is going out again. Also this summer I took the dryer apart to snug up some screws that had come lose, that were scraping the inside as the dry ran. I own a range and a dishwasher Maytag brand but will not buy another Maytag unit, even if they are built by my union brothers and sisters.

We purchased a Neptune washer/dryer combination with pedestals a few years ago. The washer vibrates so violently that I had to block it between the dryer and wall to keep it from walking across the floor during the spin cycle. We had a technician come out, and he stated that the unit just needed to be balanced. The level I used showed the washer balanced in all 4 directions. Then he said I had to balance it with the machine running to stop the vibration. That didnt work either. I had previously installed vibration dampers and the technician told me that makes the vibration worse. When is someone going to file another class action lawsuit against Maytag, as there appears to be thousands of complaints for this same washer?

Bravos XL Top loading High Efficiency Low Water Washer and Dryer - I gave this washing machine a 1 star but would give it a 0 star or less if the choice was available. I agree with everything others have voiced about this washer. I end up using the bulky cycle for everything because it is the only cycle I have found that will use enough water to get the clothes moving around. All the other cycles are a joke. First you must put everything around the wall of the tub away from the so called agitator. Then about 2 cups of water enters the machine. It then goes into this high speed spin. In my opinion it just pushes any soil deeper into the fibers. The drum will then spin slowly and water will spray on the clothes for several minutes but the washer never fills with enough water to cover the clothes. Watching it agitate through the glass top is almost hysterical. Laundry is barely moving. The high speed spin they push as a selling point puts deep wrinkles in everything and the wrinkle control setting on the dryer does nothing for them. It is absolutely the worst machine I have ever owned. My husband has repeatedly told me to sell these and buy another set. I will be ashamed to sell it to anyone. Im not sure how the makers of Maytag got away with selling these machines. I know there are different models but from what I have read they all work the same. I replaced a very low end GE Washer and Dryer with this pair and every time I do laundry I wish I had them back. The matching dryer is very costly to run as almost every load takes 2 cycles to get items dry. Nothing comes out completely dry even if you put it on the more dry setting.

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

Sometimes the control panel is difficult to work with especially if the wash is paused to add more clothes or detergent. The good things is that the tub is very large so a comforter can be washed and you can control the amount of water depending on the amount of what is being washed. I also like that it doesnt have the big agitator in the middle.

Maytag products are a waste of money! I purchased a Maytag Front Load Washer a couple of years ago during the Cash for Clunkers rebate where we were asked to give up our reliable machines for so called energy efficient new models. After spending over $1,000 on this fancy front load machine and having it installed, I go to use it the first time and it won’t work. It took me a month to get someone to come and repair the bad board on it. I then started to use it and after a year, the thing started making a horrible loud noise. I called the repair folks and they told me it is out of warranty. I called a local repair guy who told me that the drum is shot and that it will cost $700 to repair. So I got a total of 10 months of use out of this stupid thing. Thats $100 a month to do my laundry! I would be better of dry cleaning! I have searched the web and see that this is a common issue and that Maytag refuses to make this right. Well, I can choose to never buy a Maytag again. I hope that others will heed our advice and do the same.

Its an old story with Maytag. We purchased a refrigerator in Nov 2012. Three days ago we noticed the refrigerator was making a constant buzzing sound and that the freezer was not cold. A repairman confirmed our suspicions. Bad compressor! Cost to repair, $729. And, the warranty on the new compressor was only 90 days. Cost for a new one $1700. Contacted Maytag. We do offer extended warranties (up to 10 years on compressors) on some models, but not yours. So, we will get a new one but with the extended warranty. It wont be a Maytag.

I purchased our Maytag dishwasher last November. Last week, the control panel went out. I called customer service and they were actually polite and helpful, except for the fact that I had to wait an entire week to have a technician come to my house. Being that I live in the Balt/DC Metro area, I would have thought they would have enough people in the area to come over faster. Anyhow, we finally had the technician come today and tell us that the control panel needs replaced and that he highly recommends an extended warranty, which costs $200 for 5 years. He let my husband know that the repair itself would cost $500 if not covered by warranty!!! What a ripoff! I purchased this dishwasher because I grew up believing in the Maytag brand. Sounds like this is an extremely common issue and if Maytag wants to make things right, they should discontinue sale of their crap product and provide those of us who are stuck with it, a complimentary 5 year warranty. I shouldnt have to pay $200 in extended warranty to make up for the fact that my control panel is likely to go out again in another year, when Ill be forced to buy a new dishwasher.

I bought a Maytag dishwasher, stove and refrigerator and the dishwasher was a problem from the beginning. Repaired out twice and replaced the control panel. Seasonal residence, so the start of year 2 (this week) the control panel goes a third time. Its going to cost $387 to repair (told my elderly mother) and it turns out it was a warranty program that she purchased, not a repair estimate. She was misled as she called Maytag and they transferred her to a warranty company, and once again Maytag says theres nothing they will do. Now, Im hassled with cancelling that as well. I called Maytag and they dont stand behind their lemon of a product and said there is nothing they can do because its out of warranty (even though theyve been out twice to fix it). Do not buy a Maytag product. This is the first complaint Ive every written and I am just shocked that Maytag doesnt stand behind their product. Im informing 100s of people to not purchase Maytag and they will pass along my negative experience as well, for that, I am sure.

After my divorce, I bought a new house for my youngest son and me. It came without a fridge, so I used some of my settlement money to buy one I had been dying to get - stainless, French door, with bottom drawer freezer! It worked fine for the first 9 months or so. Then, water started pouring through the ceiling of my downstairs master bedroom. Turns out it was coming from the freezer water line. Ceiling tiles ruined, carpet stained. Then it started making this god awful noise. It starts, rumbles for a while (long enough to wake everyone up or give the dog a coronary), then is quiet for a while. Next, I open the freezer to find a sheet of ice across the bottom of the drawer. I assumed I had done something, so I got rid of it and thought nothing else of it. Last night, I get ready to make dinner and there is this blizzard of frost all over the freezer. It looks like a winter wonderland. I am afraid to see what is there when I go home and even more fearful to attempt to use my warranty.

Maytag Centennial eco conserve clothes washer - I purchased a Maytag (non-agitating) washer, (model MVWC400XW) just about a year ago and I cant tell you how dissatisfied I am with this product. It does not clean the simplest of soil from garments. I have actually had clothes come out of the washer after a complete wash cycle, with dry clothes. They recommend putting soap in first, at the bottom of the washer and then load clothes; I have had clothes come out stained as a result the clothes sitting on top of the soap. I am requesting that I be able to return (have this washer picked up) from my home and replaced with a washer with an agitator or a compatible washer that actually washes clothes. I believe that this may qualify as a lemon with regards to California lemon laws.

Well, my washer is 2 years old, yes thats right - 2 years old. And it only goes to the wash cycle, washes once and stops, wont complete a full cycle. Yes, the brand with the commercial with the repairman just sitting around because their products are so great you never have to work on them. Yeah right. And Ive seen videos on YouTube on the problem with the Maytags. So Maytag may want to look into it!

Washer was purchased at Lowes under direction from staff... Great washer, environmentally better, less water consumption... Well washer is piece of crap. Activator is out, door stays locked, have to unplug to release every time used, water does not drain and cycles do not function or start. Lowes no longer carries product and all other review on spot as to cost to repair... Piece of crap, loss of $600.00+. Could be used as target practice, best case scenario.

I dont even bother repairing those things. Customer calls and I say, Sorry, those are worthless. I did try but gave up. Buy Speed Queen. Traditional, heavy duty, with three-year warranty. Whirlpool who owns Maytag doesnt give a crap. They want their warranty repairmen to pass drug tests but no longer give appliance training. Speed Queen is built in Wisconsin. Who knows who is building the Maytag crap. Another customer had a similar problem with Maytag stove, 1 year old. Whirlpool and Menards said, Sorry, you didnt buy the extended warranty. I have conversations with just about every customer about junk appliances these days. Try to find used 20-year old Maytag for quality. Good luck.

Have 2 fridges (one regular and the other is a side-by-side, both were bought in 2006 at Future Shop. The small one is not freezing and the side-by-side ($2,200) is busted too (compressor wont start....). How can Maytag say that their product are reliable on TV??? A Fridges compressor should last at least 15 years !! Maytag, you should at least have the decency to pay for the compressor!

My original GE dishwasher that came with our house finally crapped out after about 8 years of use in 2007. Bought a Maytag from Home Depot for around $400. Dont remember the model number. It worked okay but then in the middle of 2010 we got a letter in the mail saying our machine was being recalled because the heating element might catch fire (!!!). The recall gave us the option of getting it fixed or getting a $150 rebate. We chose the rebate option so we trashed this dishwasher and went back to Home Depot to buy another one.We found a very nice Maytag with the stainless steel tub and the racks with the lifetime warranty against corrosion (which was good because our previous Maytag had started to leave rust on our dishes because the plastic on the tips of the rack tines was starting to come off), model #MDBA979AWB1, serial #FY2501885. The one we found was a no-box display model but it had all the accessories with it and still had the factory warranty. We got it for just over $300 and with our rebate applied we were out the door for under $200 including tax. I installed it myself and didnt have any issues for quite some time. My wife and I were both very happy with how clean the dishes got!Now, last night the dishwasher wouldnt start. I checked it out this morning, made sure it had power and was able to get some lights on the control panel to light up but still couldnt get it to start. Looks like Ive been victimized by the control board as most of these complaints have said. I guess I should consider us lucky since ours seems to have lasted longer than the average 18 months to 2 years. Will be contacting Maytag and Home Depot to see what they can do but after reading all these negative reviews Im not hopeful.

I bought Maytag frost-free refrigerator last August 2006. But now, I noticed that ice builds up in the freezer. The product is only five years old but I was told by Whirlpool that they had discontinued making defrost heater. The reason why I bought Maytag was the ad on TV showing the Maytag service technician seating and doing nothing, implying that Maytag brand is a good product. Think again before buying Maytag products.

I purchased Maytag washer, as it was rated the best of the best at the store. First of all, Delicates cycle washes exactly like Normal. All my sweaters got ruined as the agitation is VERY HARD. I dont think the manufacture even knows what that cycle means! Absolutely awful! Theres no difference between Delicates and any other cycle!Second, Deep fill cycle. If you select off on that cycle the clothes get hardly damp. HOW can you wash hardly damp clothes???? If you go with Deep fill, the washer is supposed to weigh your laundry 1st and ONLY pour the water according to the weight. Well.... you can put only 5 small items and the washer fills all the way to the top! What the hell is this???? How can few items fill such a ginormous washer???? It doesnt work! Im so pissed and want this washer out of my laundry room!

I purchased by Maytag Bravo from Lowes exactly 1 year ago when the gearbox failed. There was a loud grinding sound as the washer tried to shift from wash to spin. Reading through some on-line reviews and complaints it turns out that this is not a new problem and has been known to Maytag for some time. I specifically bought a Maytag because of their prior reputation for quality. Unfortunately, my information was out of date. It is so sad that a company would compromise such an outstanding reputation.

We bought MDB7759AWB Maytag dishwasher in 2011. It worked decently until now when it stopped delivering water to the upper rack. The cleaning quality on the lower rack also dropped significantly although it might be due to the lack of water delivery to the upper rack. Apparently there is something wrong with the internal pump. The Maytag service offered a repair for $300+ which I rejected because this is a ridiculous cost and I would rather buy a different dishwasher. My conclusion is that if you buy Maytag dishwasher you need to factor about $300+ for the repair(s) in 5 years as apparently they do when they sell you this product. Anyway, even though Maytag was a decent brand a long time ago (probably in the past century), it is not reliable anymore. It does not mean it has to be much worse than many others but if you are looking for something better than those others I would not recommend Maytag.

I bought this dryer 3 years ago and the fuse has blown three times. The dryer gets really hot and blows a fuse. The entire back of the dryer is clean and free of lint, the hose on the back, and the ventilation pipe running out of the house are completely clear, but the dryer continues breaking down. The Whirlpool NC folks have been out here three times yet it has broken down once again. I should not have to purchase another dryer after only three years!

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!

In 2016 I purchased a matching Maytag washer and dryer. The reason why I purchased it because I was in a house and I no longer had a washer and dryer and I refuse to go to a laundry mat at the city to go to Nebraska Furniture Mart and it was a number of different washer and dryer combinations available. I had previously own a Samsung matching washer and dryer and it worked fine, my Maytag has dame of the same features and works great.

I purchased this machine (Maytag washing machine model MVWB700VQ0) from Home Depot in December of 2008. When purchasing it I decided to spend a bit more money on the machine, thinking I would get a quality product. For the last two years and 5 months it has only been me and my wife in the house as the kids are in college. Hence, the washer has not been used as much as some would use it. Within the last two and one half weeks the machine started making a horrible growling noise (probably the tub bearing going bad) and then started to leak yesterday. I noticed this morning that there was a large puddle of bleach water coming from under the machine. I called Maytag, which is just a fancy name for Whirlpool, and they basically told me too bad. It is inconceivable that a machine that used to last 20-plus years barely lasted three with only two adults using it. When I owned my previous home in another town the house came with Whirlpool appliances which literally fell apart within 5 years. I wanted to stay away from Whirlpool; however, I did not know that Maytag was owned by Whirlpool. I have received no assistance from Maytag. I am absolutely disgusted with the fact that an American iconic company such as Maytag is producing such garbage. I am going to be forced to figure out and fix what is wrong with the machine myself. However, I do believe this subject should be looked into further and possibly a class action law suit against Maytag for bad customer service since there seems to be quite a few people with issues surrounding this machine.

If I could give this a 0-Star rating, I would! I cant believe Maytag would make such an awful washing machine! Within the first 2 weeks I called their service department because (in my opinion) the washer wasnt washing properly. It took over a month and several calls to get someone out to look at the washer & dryer. According to the technician, both machines were operating properly. Apparently the washer is designed to destroy clothing and bedding! The gentle cycle set on deep fill will add just enough water to get the clothing wet, then agitates for about 10 minutes, then it fills up, agitates for 3 more minutes and drains. During the 10 minute dry-run, I watch my clothes get destroyed! I have never seen anything like this! My sweaters are shredded, my tops are pilled up & in a garment bag this thing managed to destroy a sports bra! This machine has ripped my mattress cover in several places and pulled my sheets from excessive rubbing due to not enough water. And what is up with the slow fill? The technician informed me that the trickling water is also normal. If I could return this washer, I would! I will never buy another Maytag because my Bravos washer died after only 4 years, and this one is brutal!

Purchased Maytag front load washer model MHW6630HW from Home Depot. Machine was installed 9/15/19. From inception we had issues that have escalated. Machine leaks and makes strange hissing sounds. Home Depot has no record of the purchase in their website now. We tried to return it within days. We contacted Home Depot executive offices and they keep sending Paradise Appliance repair. The repair people do nothing and keep saying we have to come back again for you to be considered for replacement. Home Depot is dragging their feet and we are concerned about the six month deadline. The Maytag does not do an effective job washing and clothes comes out wrinkled. Concerned about the sporadic leak getting worst and doing damage to floors.